lighting control engine

Lighting Control Engine
Setup Manual
www.ecue.com
Lighting Control Engine - Setup Manual
© e:cue lighting control
An OSRAM Company
Rev. 1_04/2010
Lighting Control Engine - Setup Manual
Table of Contents
1.Device Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.1 About the LCE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
1.2 Highlights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.Delivery Content & Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.1 Included in the package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.2 Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3.Brief Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
4.Important Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4.1 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4.2 Transport. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
4.3 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
5.Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5.1 Inspect the delivery scope. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5.2 Set up the device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
5.3 Installation location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5.4 Switching on/off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
6.System Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
6.1 Touch-screen calibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
6.2 Changing the computer's network address. . . . . . . . . . . . . . . . . . 12
6.3 Adjust the programmer's network settings . . . . . . . . . . . . . . . . . . 15
6.4 Performing maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
7.Technical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
7.1 General specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
7.2 Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
8. Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
8.1 Overview of LCE connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
8.2 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
9. Legal Notice / Warranty Disclaimer. . . . . . . . . . . . . . . . . . . . . . . . 25
Lighting Control Engine - Device Overview
1. Device Overview
1.1 About the LCE
Designed to control large and complex projects, the Lighting Control Engine
(LCE) is a high performance server with the e:cue software suite pre-installed. As
a central control unit this versatile lighting control server orchestrates all devices
and fixtures within a project. The LCE is able to output DMX/RDM, e:net, and
other protocols such as KiNet and ArtNet. This and the capability to integrate
various audio/video, external triggering as well as other devices and content, the
LCE is the ultimate solution for the most demanding projects. A built-in touchscreen monitor on the front panel of the attractive, durable aluminum casing
provides user interaction with custom graphic user interface designs. The LCE
can be mounted in a 19-inch rack.
1.2 Highlights
• Integrated touch-screen for control and monitoring
• Pre-installed e:cue Lighting Application Suite
• Reliable, uninterrupted operation
• Supports various Ethernet-based protocols
• Control of up to 65,536 DMX channels
• E-mail notification and status reports
• Easily mountable in a standard 19” rack
• Integration of media content
• 2 x RS232
• 16 digital inputs
• Ethernet (e:net)
• MIDI
4
Lighting Control Engine - Delivery Scope
2. Delivery Content & Accessories
2.1 Included in the package
• e:cue System Manual Basic
• e:cue System Manual Advanced
• DIN A6 Setup Manual
• HDMI to DVI adapter
• Screw driver
• 2m CAT5e SFTP cable
• AC power cord DE, UK, US
• Rack mount kit
2.2 Optional Accessories
Item-Number
• AC power cord DE
PS.AC.0000.100
• AC power cord US
PS.AC.0000.101
• AC power cord UK
PS.AC.0000.300
• AC power cord AU
PS.AC.0000.400
• AC power cord JP
PS.AC.0000.500
5
Lighting Control Engine - Brief Description
3. Brief Description
Front
1. Ventilation slots
2. Front USB
3. On/off switch
2
4. LED
5. Touch-screen
1
3
4
5
Back
1.
2.
3.
4.
5.
16 digital dry contact inputs
DMX out
Fan
Power connection 
1
2
DMX in
4
6
5
6. Connection for external devices
7. Network card
8. Monitor connection
3
6
7
8
Lighting Control Engine - Important Notes
4. Important Notes
4.1 Safety instructions
Only use the device in compliance with the environmental
conditions specified in the LCE data sheet.
Operate the server only in environments having a low dust
content in the ambient air.
To prevent the device from overheating, only operate it in wellventilated environment. The LCE ventilation slots may not be
obstructed.
Device components can reach high temperatures.
Actions described in this manual may only be performed with
special care by skilled personnel.
LCE repairs may only be carried out by authorized, specially
trained personnel. When in doubt, contact e:cue service.
7
Lighting Control Engine - Important Notes
4.2 Transport
Only transport the LCE in its original packaging. This protects the server from
damage.
Only unpack the LCE at its installation location.
To protect the device against condensation water, unpack it and wait until all
moisture remaining in the LCE has evaporated. Condensation can occur when
the device is moved from a cold to a warm location.
4.3 Cleaning
To clean the device, disconnect it from the line power supply. Disconnect all
devices connected to the server.
Depending on the operating environment, the server interior must be cleaned.
This cleaning may only be carried out by skilled personnel.
Do not use any cleaning agents containing solvents (e.g. acetone, alcohol or
thinner) or abrasives.
The housing surface and touch-screen can be cleaned with a moist, lint-free cloth.
Ensure that no water penetrates into the housing. Otherwise, this could damage
the electronics.
8
Lighting Control Engine - Commissioning
5. Commissioning
5.1 Inspect the delivery scope
Unpack the LCE and inspect all parts for completeness (see also Chapter 2). Keep
the packaging for use in case of further transport. If there is apparent damage
to the device or parts are missing from the delivery scope, please contact e:cue
service.
5.2 Set up the device
You can use the LCE as a desktop or rack-mounted device. As delivered, the
server is configured as a desktop device. The hardware for mounting in a 19"
rack is included in the delivery scope.
To mount in a rack, fasten the rack brackets and 19" installation brackets to the
server. Then, fasten the brackets to the front and rear of the server rack.
Ensure that the server rack is sufficiently ventilated.
9
Lighting Control Engine - Commissioning
5.3 Installation location
- In case of desktop operation, place a non-slip pad beneath the server. This
prevents damage to the server and the installation location.
- Do not obstruct the ventilation slots.
- There must be at least 10 cm distance to other devices or objects.
- Do not stack several devices on top of each other, otherwise this could lead to
overheating.
- Install the server in a location where the device is protected against dust, heat,
moisture and vibration.
- Only install the device in a vertical position. All other operating modes are
prohibited.
5.4 Switching on/off
Initial start up
Connect your devices to the server and connect with the line power supply. Once
the line power supply is connected, the LCE switches on automatically. The front
LED indicators light up in green. Red blinking of the LEDs indicates hard drive
activity. You can now see on the touch-screen that the server has started.
Switching on again
For normal switching on of power, press the On switch on the left side of the
LCE.
Normal switching off
Only switch off power to the LCE by shutting down the operating system.
Disconnecting the operating voltage can lead a loss of data.
Switching off in case of error
If the operating system does not respond, press the Off switch on the LCE and
keep pressed until the LCE switches itself off.
10
Lighting Control Engine - System Configuration
6. System Configuration
All steps shown here relate to the English version of Microsoft®
Windows 7™. If you have a different language version, it is
possible that expressions change. The default language of the
operating system is English.
6.1 Touch-screen calibration
Open the menu in task bar and right-click on the "Touchmon" icon.
11
Lighting Control Engine - System Configuration
Click on "4 points calibration"; a window opens for calibrating the touch-screen.
Follow the instructions on the screen.
6.2 Changing the computer's network address
To change the network address of one of the installed network cards, click on the
"Start" icon and enter "Connections" in the search box.
12
Lighting Control Engine - System Configuration
Select "View network connections" in the hit list.
You now see all available connections. Right-click on the
desired connection and select "Properties".
13
Lighting Control Engine - System Configuration
In this open window click on "Internet Protocol Version 4 (TCP/IPv4)", then press
the "Properties" button.
Enter the appropriate address for the network. Confirm your input by clicking on
the "OK" button. You can close all windows now. The network connection is now
configured.
14
Lighting Control Engine - System Configuration
6.3 Adjust the programmer's network settings
Start "Programmer Enterprise 5".
Click on "Extras" and select "Application Options".
15
Lighting Control Engine - System Configuration
In the menu, under the "Advanced" tab, you can specify which network card the
programmer software e:net should output to. You can also specify this setting for
the "ArtNet" and "KiNet" protocols.
e:cue recommends only outputting one protocol per network card.
16
Lighting Control Engine - System Configuration
6.4 Performing maintenance
This section contains instructions for maintaining the server hardware. Consult
with e:cue before performing any of this work. Work on the server may only
be performed by trained personnel and in compliance with the ESD guidelines.
Non-compliance can cause damage to the system.
Open the server housing
To open the housing, remove the LCE from the 19" rack if necessary. Unfasten
the six screws. The red cover can now be taken off as shown.
17
Lighting Control Engine - System Configuration
Replacing the hard drives
Each hard drive can be removed by unfastening three screws. Only use hard
drives for replacement that have been approved by e:cue.
18
Lighting Control Engine - System Configuration
Battery replacement
The server's CMOS battery can be replaced if it is exhausted. Only use the same
type of batteries that e:cue has approved for use.
19
Lighting Control Engine - Technical Specifications
7. Technical Specifications
7.1 General specifications
Item Number
Lighting Control Engine
EN.LC.9000000
General Specifications
Dimensions mm / inch
504.5 x 487 x 132.4 mm/ 19.86 x 19.7 x 5.21 inch
Weight kg / lbs
12 kg / 26.45 lbs
Power
100-240V AC, 600W
Operating / storage
temperature
0° - 35°C / 32-95°F
Operating / storage
humidity
0-80%, non-condensing
Environment
IP20
Housing
Steel, aluminum
Mounting
Desktop, 19" mounting
Certifications
CE
20
Lighting Control Engine - Technical Specifications
Engine specifications
User interface
Keyboard / mouse / touch-screen
Operating system
Microsoft® Windows 7™ Ultimate
System connection
ports
2x e:net (RJ45 Ethernet)
Outputs
2x DMX (XLR5-Pin)
2x RS232 (D-Sub9)
MIDI
1x DVI
Audio
Inputs
Video
DMX (XLR5-Pin)
RS232 (D-Sub9)
MIDI
Digital dry contact inputs
Display
XGA (1024x768)
Data storage
2x 250 GB hard disks (RAID 1)
21
Lighting Control Engine - Technical Specifications
7.2 Dimensions
mm// 17.64
17.64 inch
448448
mm
inch
441mm
mm //17.36
inch
441
17.36
inch
57.5
57,5mm
mm / /
2.26 inch
2.26
inch
132,4
mm // 5.21
132.4
mm
5.21inch
inch
22,5 mm
22.5
mm/ /
0.89 inch
0.89 inch
466mm
mm / /18.35
inch
466
18.35
inch
22
DMX In
Power In
S/PDIF
DMX Out
Mouse/
Keyboard
MIDI
16 Digital
dry contact
inputs
RS232
Audio in/out
SMPTE,
Timecode in
e:net
Art-Net
USB KiNET
Fire Wire
e:net
Art-Net
KiNET
DVI
Video In
HDMI
Lighting Control Engine - Appendix
8. Appendix
8.1 Overview of LCE connections
23
Lighting Control Engine - Appendix
8.2 Safety instructions
The electronic components are very sensitive to electrostatic
discharge (ESD).
Be careful not to touch the components. Please do all preparation
work on a static-free surface. Please always ensure to wear an
antistatic wrist strap.
Any usage other than described in this manual is not permitted,
can damage the device and lead to associated risks such as shortcircuit, fire or electric shock. If not otherwise noted, no part of the
product may be modified or rebuilt.
24
Lighting Control Engine - Legal Notice / Warranty Disclaimer
9. Legal Notice / Warranty Disclaimer
Author: Gregor Bauer
Layout & typesetting: Nadine Topp
Illustrations: Gregor Bauer, Nadine Topp
Print: Bonifatius GmbH, Paderborn
© 2010 e:cue control GmbH | An OSRAM Company
Im Dörener Feld 11 | 33100 Paderborn | Germany
web: www.ecue.com
e-mail: [email protected]
All rights reserved.
is a registered trademark of e:cue GmbH & Co. KG. All other company
and/or product names are trademarks and/or registered trademarks of the
respective manufacturer.
The products might possibly differ slightly from their depiction. Characteristics,
performance and technical data can vary, depending on the operating system
and hardware used. We reserve the right to make changes at any time without
previous notice.
provides no guarantee of functional suitability for a specific purpose,
the marketability or other product characteristics. No other guarantee claims can
be asserted against e:cue through legal or other means. e:cue Lighting Control
assumes no responsibility or liability for damages under any circumstances and
of any nature, not only loss of sales and profit, but also including damages:
• arising from use of the product
• resulting from the loss of usability of the product
arising from misuse or occurrences, circumstances or actions over which e:cue
has no influence, regardless of whether the damages are incurred directly or
indirectly, or whether the damages are of a special or other nature, and whether
these damages are incurred by the holder of this guarantee or a third party.
25
© 2010 - e:cue control GmbH - An OSRAM Company - Germany - www.ecue.com