DRP-710-Suzuki gsxr 600-750 11-15

Comments

Transcription

DRP-710-Suzuki gsxr 600-750 11-15
Driven TT Rearsets for 11-15 Suzuki GSXR 600/750
Part#: DRP-710
INSTALLATION INSTRUCTIONS
Removal
Shifter Side
1. Remove shift rod from shifter.
2. Remove C clip from shift pedal and remove pedal.
3. Remove 2 M8 bolts from frame bracket and remove plate from bike.
Brake Side
1. Remove 2 M6 bolts holding the master cylinder.
2. Remove master cylinder plunger pin and retain split pin.
3. Remove 2 M8 bolts and remove frame bracket.
4. Remove rear brake switch and disconnect it from bike.
TOOLS REQUIRED
•
•
•
•
•
•
•
•
8mm Open End Wrench
5mm Hex Key
6mm Hex Key
8mm Hex Key
Needle Nose Pliers
Screw Driver
Blue Loctite
Impact Gun
THE USE OF BLUE LOCTITE IS REQUIRED ON ALL MOUNTING HARDWARE!
Installation
NOTE: ALL PIVOT POINTS MUST BE TIGHTENED USING BLUE LOCTITE AND AN IMPACT GUN.
Shifter Side
1. Install new shift pedal and reinstall C clip.
2. Install shift rod.
3. Install foot peg into left bracket.
4. Install frame bracket using stock M8 bolts.
5. Adjust shift pedal with shift rod and tighten both safety nuts.
Brake Side
1. Install foot peg in frame bracket.
2. Connect master cylinder plunger to brake lever using oem cotter pin and pin.
3. Install frame bracket to bike.
4. Install master cylinder using 2 M6 bolts supplied.
5. Use blue Loctite on all bolts and torque all to required setting.
6. Make sure nothing interferes with proper operation of motorcycle.
TORQUE VALUES
•
•
•
•
M5 = 6FT/LBS
M6 = 10FT/LBS
M8 = 25FT/LBS
M10 = 45FT/LBS
Make final adjustments as necessary and re-check all hardware after the first 500 miles of use.
(Fig 1.)
(Fig 2.)
Driven TT Rearsets for 11-15 Suzuki GSXR 600/750
Part#: DRP-710
100036
LEFT SIDE / SHIFTER
A00018
M6 x 1.0 x 12 SFHCS
M10 x 1.5 x 25 SBHCS
100191
100113
100115
M6 NUT L/H
M6 x 1.0 x 12 SBHCS
A00005
M6 x 1.0 x 16 SBHCS
A00001
M6 x 1.0 x 12 SHCS
100196
100078
100195
RIGHT SIDE / BRAKE
A00019
M6 x 1.0 x 20 SBHCS
M6 x 1.0 x 16 SHCS
100035
M6 x 1.0 x 12 SFHCS
100193
M10 x 1.5 x 25 SBHCS
100192
M8 x 1.25 x 20 SHCS
100115
100102
100078
M6 x 1.0 x 25 SHCS
100194
100065
M6 x 1.0 x 12 SBHCS
A00002

Similar documents

DRP-710-Suzuki gsxr 600-750 11-15

DRP-710-Suzuki gsxr 600-750 11-15 1. Install foot peg in frame bracket. 2. Connect master cylinder plunger to brake lever using oem cotter pin and pin. 3. Install frame bracket to bike. 4. Install master cylinder using 2 M6 bolts s...

More information

Driven TT Rearsets for 14-15 Yamaha FZ-09 Part#: DRP

Driven TT Rearsets for 14-15 Yamaha FZ-09 Part#: DRP 5. Pull swing arm pivot out. (support swing arm as it will fall down if not supported) 6. Remove m8 bolt from lower plate. 7. Remove left side plate. Brake Side 1. Remove rear brake master cylinder...

More information

Driven TT Rearsets for BMW S1000RR 09-14 Part

Driven TT Rearsets for BMW S1000RR 09-14 Part 8mm Open End Wrench 5mm Hex Key 6mm Hex Key 8mm Hex Key Needle Nose Pliers Screw Driver Blue Loctite Impact Gun

More information