Sicame Australia - Australian Powerline Industries

Transcription

AUSTRALIA
INSULATION PIERCING CONNECTORS
LOW VOLTAGE INSULATED SERVICE FITTINGS
LOW VOLTAGE WATERPROOF CONNECTION
SYSTEMS
SERVICE FUSE HOLDERS
LVABC HARDWARE
SHEAR BOLT CONNECTORS
PRODUCT CATALOGUE
PERSONAL SAFETY EQUIPMENT
INSULATING GLOVES
1000V INSULATED TOOLS
INSULATING MATS
EARTHING SYSTEMS
DETECTORS AND INSTRUMENTS
ELECTRICAL SAFETY EQUIPMENT
PRODUCT CATALOGUE
w
0705
WELCOME TO SICAME AUSTRALIA PTY LTD
THE NEW GENERATION OF OVERHEAD AND UNDERGROUND SEALED
INSULATION PIERCING CONNECTORS AND FITTINGS
Sicame Australia Pty Ltd has established a strong reputation as the leading manufacturer and supplier of Low
Voltage Aerial Bundled Cable (LVABC) Insulation Piercing Connectors and associated equipment in Australia.
In response to the growing trend toward the adoption of Overhead Aluminium XLPE Service Cable by numerous
supply authorities, Sicame Australia has developed a complete range of products specifically designed for the
purpose. This system allows a safe, economic and speedy installation of a customer to overhead mains with provision for cable connection, support and fusing at both the house end and pole end.
These products have been tested to the relevant Australian Standards for connectors and hardware as well as
European and American Standards. IPC products have been tested in compliance with AS4396 (Int.) 1996 for
IPC’s.
This catalogue will guide you through the range of overhead and underground connectors and other products that
are currently approved and utilised by your local electricity utility.
We commend these products to you and your customers.
Robert Battle
Managing Director
The team at Sicame Australia headquarters in Queensland
© Sicame Australia Pty Ltd. The information presented here is subject to change without notice.
QLD Sales Office: Ph 07 38077022, Fax 07 38077522
NSW Sales Offices: Sydney Ph 02 96213155, Fax 02 96227120
CATALOGUE INDEX
SECTION A - LVABC CONNECTORS & FITTINGS
A1
TTD series IPCs
A2
NTD series IPCs
A3
In Line Piercing Connectors
and Industrial Mains Box
A4
Multi-tap IPCs & Earthing
A5
LVABC Fuse Switch Disconnectors
A6
LVABC Fuse Switch Accessories
SECTION B - SERVICE FITTINGS
B1
House Service Connectors
B2
CAW & CCW series service connectors
B3
Mains Connection Boxes
B4
Service Fuse Holders
SECTION C - PRE-INSULATED FITTINGS
C1
MJPB & MJPT series links
C2
Pre-crimped links and tools
C3
MEPCN series
C4
CPTA & CPTAU series lugs
I
0107
SECTION F - STRAIN & TERMINATION FITTINGS
F1
Service termination clamps
F2
Mains termination & suspension clamps
SECTION G - HARDWARE
G1
Eye bolts, J & Q hooks, brackets
G2
Eye nuts, weak links
SECTION H - TIME AND LIGHT CONTROLS
H1
P.E. Cell - Enclosed light arrestors
SECTION J - CATU SAFETY EQUIPMENT
J1-J4
Personal Safety
J5-J17
1000V Insulated Tools
SECTION K - EARTH Systems Accessories
K1-K6
Earth Set Accessories
K7
Earth Clamps
K8
Earth and Stick Bags
K9
Lanyards
SECTION D - UNDERGROUND CONNECTORS
D1
MUCI Series submersible
D2
Resin Filled Service Tee Joint
D3
Bi-form & Tri-form connectors
D4
BST & LVM Mechanical Branch Connectors
D5
MF Series Mechanical In-Line Connectors
D6
UM Series Mechanical In-Line Connectors
D7
MF15 HV Mechanical Connectors
D8
MF17 HV Mechanical Connectors
D9
ML Series Mechanical Connectors (Lugs)
D10
WB1, 2 & 3 Series - Mains to Mains
Branch Connectors
D11
WB4 Mains to Mains Branch Connector
D12
WS2 - Mains to Service Branch Connector
D13
D14
D15
D16
Protective Covers
SECTION E - TOOLS & ACCESSORIES
E1
Spanners, testers and wedges
E2
Cutters and Strippers
E3
Stringing tools
E4
Stringing tools
E5
Jointing Tools
E6
Battery Operated Driver
LVABC CONNECTORS
TTD Series
A1
0107
For Connecting INSULATED MAINS to INSULATED MAINS or INSULATED SERVICES
The Sicame TTD range of insulation piercing connectors (IPCs) provide a fast, convenient and reliable method of connecting overhead low voltage mains to services or other mains. All common types of conductors can be interconnected, including insulated aluminium or copper. The connectors have been tested to AS4396 and are approved for
use by Australian power distribution utilities (Consult for further details).
TTD SERIES INSULATION PIERCING
CONNECTOR:
Product
Number
Mains Cable
(mm2)
Branch
Cable
(mm2)
Number
of Bolts
Bolt
Size
Pack
Size
Application:
Mains cable: Insulated copper or aluminium
Tap cable: Insulated copper or aluminium
TTD051XFA
16 to 95
1.5 to 10
1
M8
12
TTD101XFA
6 to 54
6 to 35
1
M8
12
TTD151XFA
25 to 95
6 to 35
1
M8
12
Features:
* Provides a fully sealed, waterproof connection
* No need to strip cable to make the connection
* Simultaneous piercing on main & tap
* Torque controlling shear heads on all bolts
* Tightening bolts do not come into contact with live
components
* Captive end cap for protection of tap cable, which
can be mounted on either side.
* Fully bimetallic
* Stainless steel fasteners
TTD201XFA
35 to 95
25 to 95
1
M8
12
TTD241XFA
50 to 150
6 to 35
1
M8
12
TTD251XFA
50 to 150
35 to 95
1
M8
8
TTD301XFA
25 to 95
25 to 95
2
M8
10
TTD341F *
50 to 150
6 to 35
2
M8
10
TTD351XFA
50 to 150
35 to 95
2
M8
4
TTD401XFA
50 to 185
50 to 150
2
M8
4
TTD431XFA
70 to 240
16 to 95
2
M10
4
TTD451XFA
95 to 240
95 to 240
2
M10
4
Testing Specification:
Tested to AS4396
TTD551FJA*
120-380
95-240
2
M10
4
*Galvanised fasteners
Installation Notes:
When using 2 bolt connectors from this range, each
bolt must be tightened a 1/4 to 1/2 turn
alternately, until the shear head operates.
For tightening the shear head bolts, use only a 13mm
AF, six sided hexagon socket (17mm AF for models
TTD431XFA, TTD451XFA & TTD551FJA models).
For double insulated cables, the outer sheath
should be removed before applying the connector.
TTD151XFA
TTD301XFA
Recommended tool for all products: RPS13/17-6H or RPS13/17-6SH
LVABC CONNECTORS
NTD Series
A2
0107
For connecting BARE MAINS to INSULATED MAINS or INSULATED SERVICES
The Sicame NTD range of insulation piercing connectors provide a fast, convenient and reliable method of connecting
overhead low voltage mains to services and other mains. All common types of conductors can be interconnected, including bare aluminium or copper mains. The connectors have been tested to relevant standards and are approved for
use by Australian power distribution utilities (Consult for further details).
NTD SERIES INSULATION PIERCING
CONNECTOR:
Application:
Mains: Bare copper or aluminium
Tap:
Insulated copper or aluminium
Features:
* Provides a fully sealed, waterproof connection on the tap.
* No need to strip cable to make the connection
* Simultaneous piercing on main & tap
* Torque controlling shear heads on all bolts
* Tightening bolts do not come into contact
with live components
* Captive end cap for protection of tap cable,
which can be mounted on either side.
* Fully bimetallic
* Stainless steel fasteners
Product
Number
Bare Conductor
Type
Size
(mm2)
Diameter
(mm)
Insulated
No. of Bolt Pack
Cable
Bolts Size Size
2
(mm )
Connectors for Bare Copper Mains
NTD101F *
Cu
7 to 54
3.0 to 10.0
6 to 35
1
M8
12
NTD301XFA
Cu
7 to 95
3.0 to 12.5
35 to 95
2
M8
10
NTD351XFA
Cu
50 to 150 9.0 to 15.7
35 to 95
2
M8
10
NTD401XFA
Cu
50 to 150 9.0 to 15.7 50 to 150
2
M8
4
Connectors for Bare Aluminium Mains
NTD101AF *
Alu
6 to 54
3.0 to 9.5
6 to 35
1
M8
12
NTD301AXFA
Alu
7 to 95
3.0 to 12.5
35 to 95
2
M8
10
NTD351AXFA
Alu
50 to 150 9.5 to 15.8
35 to 95
2
M8
10
NTD401AXFA
Alu
50 to 150 9.5 to 15.8 50 to 150
2
M8
4
NTD431AXFA
Alu
95 to 240
12.5 to
19.6
35 to 95
2
M10
4
NTD451AXFA
Alu
95 to 240
12.5 to
19.6
95 to 150
2
M10
4
*Galvanised fasteners
Installation Notes:
When using 2 bolt connectors from this
range, each bolt must be tightened a 1/4 to
1/2 turn alternately, until the shear head operates.
For tightening the shear head bolts, use only
a 13mm AF, six sided hexagon socket
(17mm AF for models NTD431XFA and
NTD451XFA).
NTD301XFA
For double insulated cables, the outer
sheath should be removed before applying the connector.
NTD351AXFA
NTD101F
LVABC CONNECTORS
ILC Series
IN-LINE PIERCING CONNECTOR
A general purpose in-line piercing connector
for aluminium or copper insulated cable in the
range 6 - 95 sq mm.
• Piercing connectors both sides
• Employs proven shear head technology
• Fully waterproof
• Complies with relevant sections of AS4396
• Fully insulated - no exposed live parts
• No crimp tools required
• Fits mains box below
A3
0107
Product
Number
Cable Range
(sq mm)
Bolt Head A/F
(mm)
Pack Size
(pcs)
ILC 695
6 to 95
13
10
Pack
Size
(pcs)
Installation Notes:
Use only a 13mm AF, six point hexagon
socket to tighten bolts.
All other connections made on the service and
consumers cable must also be waterproof to
prevent moisture ingress through the cable
into the connector.
3 PHASE INDUSTRIAL MAINS BOX FOR
IN-LINE PIERCING CONNECTORS
• Fully insulated connection system
• IP66D rated
• Designed to house the ILC 695 (see above)
• Fully UV Stabilised
• Protects connectors from accidental damage or
contact
• Ideal for connecting commercial and industrial
200Amp services
• Rear entry of consumer mains cable
• Protects consumer mains cables from UV
• Water shedding
• Attractive design
• Supplied complete with 4 x ILC 695 connectors
ILC 695
Product
Number
Description
Number of
ILC695
connectors
included
MCB1/2ILC
Single phase Industrial MCB
supplied with connectors
2
4
MCB3/4ILC
Three phase Industrial MCB
supplied with connectors
4
4
MCB3/4ILC
LVABC CONNECTORS
Multi-ports and Earthing
MSC SERIES - MULTIPLE SERVICE
Mains: Insulated copper or aluminium
Bare copper or aluminium
Branch: Insulated copper or aluminium
* Resealable test point
* Reduces pole top congestion
* Up to 4 independent taps available
MSCA/50150X
A4
0107
Description
Product
Number
Mains Cable
Type
Mains Cable
Range (mm2)
Branch Cable
Range (mm2)
Pack
Size
MSCI/3595X
LVABC
25 to 95
4 x 6 to 35
10
MSCI/50150X
LVABC
50 to 150
4 x 6 to 35
10
MSCC/795X
Bare Copper
7 to 95
4 x 6 to 35
10
MSCC/50150X
Bare Copper
50 to 150
4 x 6 to 35
10
MSCA/50150X
Bare Aluminium
50 to 150
4 x 6 to 35
10
EPC SERIES - Earth/Temporary Bond
Bond: To any suitable cable using
integral lug connecting bolt
Product
Number
*Fully heat cycle and
short circuit tested
Description
Mains Cable
Range (mm2)
Bonding
Bolt Size
Pack
Size
EPC1-301
25 to 95
M12
12
EPC1-401
50 to 185
M12
12
Both products supplied with suitable IPC
TT2D SERIES - Twin Tap IPC
Branch: Insulated copper or aluminium
Mains Cable
Range (mm2)
Branch Cable
Range (mm2)
Pack
Size
TT2D83XF3A
25 to 95
2 x 6 to 35
12
TT2D87XF3A TT2D87XF3A
50 to 150
2 x 6 to 35
12
DTA TWIN TAP ADAPTOR
Use with most IPCs to provide two independent taps.
DTA2/635
TTDx-CC SERIES - Test / Earth Tap
Branch: Bayonet style connecting port
for temporary earths or test
points
* includes phase/neutral identification tags
TTD2-CCXA
Description
Product
Number
Product
Number
Product
Number
Branch Cable
Range (mm2)
Pack Size
DTA2/635
2 x 6 to 35
12
Description
Mains Cable Range
Tap-off Fitting Type
(mm2)
Pack Size
TTD1-CCXA
16 to 35
4mm male bayonet
10
TTD2-CCXA
35 to 95
4mm male bayonet
10
TTD3-CCXA
50-150
4mm male bayonet
10
LVABC MAINS FUSE SWITCHES
A5
0107
160A, 250A & 400A Fuse Switches
The full range of ADC Krone LVABC
Fuse Switches
• Fully insulated
• On-load switching capability
• Corrosion resistant connections
• One or three pole units available
• Suits standard hook stick
• Full range of accessories available
• Utility Approved
Fuse Switches
Product
Number
Rating
Poles
Cable Range
Cable Connection
Method
FSD KGH160/1T
160 A
1
1 x 16-95 sq mm Al/Cu
Tunnel type
Integral mounting bracket
FSD KGH160/3T-L
160 A
3
Tunnel type
Includes mounting bracket
FSD KGH160/3P
160 A
3
IPC type
FSD KGH250/3P
250 A
3
IPC type
FSD KGH400/1L
400 A
1
12mm stud for lug
Max lug width 40mm
FSD KGH400/3L
400 A
3
12mm stud for lug
Max lug width 40mm, includes mounting
bracket
FSD KGH400/3TP
400 A
3
2 x 25-185 sq mm (in) Al/Cu
2 x 25-150 sq mm (out) Al/Cu
Tunnel type (in)
IPC type (out)
FSD KGH400/3PT
400 A
3
Pillar terminals
FSD KGH400/3P-LINK
400 A
3
IPC
Notes
Includes mounting bracket link storage kit
fitted to lower housing
Full technical specifications available on request.
FUSE SWITCHES ACCESSORIES
A6
0107
Mounting Brackets
Product Number
Description
FMB KGH160
Triple pole mounting bracket for three160A fuse switch units,
includes hardware
FMB KGH400
Triple pole mounting bracket for three400A fuse switch units,
includes hardware
FCA KGH400
Cross arm mounting bracket for one 400A switch fuse unit.
FMB APR630
Mounting bracket for three APR630/1 switches
P/N: FMB KGH160
Solid Links
Product Number
Description
FCL 400/630
Solid connecting link 400A/630A Size 2
FCL KGH-LINK BOX
Connecting-Link Storage Kit (for fitting to lower housing of switch)
FCL 250
Solid Connecting link 250A Size 1
FCL 250
Fuse Cartridges
Product Number
Size
Rating
Suitable for FSD
FC 160NH00G
00
160A
KGH160
FC 160NH1G
1
160A
KGH250, KGH400
FC 200NH1G
1
200A
KGH250, KGH400
FC 250NH1G
1
250A
KGH250, KGH400
FC 315NH2G
2
315A
KGH400
FC 400NH2G
2
400A
KGH400
SERVICE FITTINGS
HSC Series
B1
0107
The HSC series of connectors have been specially designed to connect consumers mains (house side) to insulated
overhead service mains (service side). Fully insulated and equipped with torque control shear-head bolts, the HSC is
safe and easy to use. No stripping of insulation is required on the service mains side. The consumers mains side requires 17mm of insulation to be stripped.
HSC SERIES
Application:
Service side: Insulated copper or
aluminium
Mains side: Consumers mains
(house)
cable
Features:
* Shear heads on both connections
* Complies with relevant sections of
AS4396
* Fully bimetallic
* Easily fits into Sicame Australia
mains boxes (MCB Series).
* Totally insulated and waterproof
* IP67 rated
Product
Number
Consumers
Mains Cable
House side)
(mm2)
Service
Side Tap
Range
(mm2)
Copper
Earth Tail
Length
(mm)
Lug
Hole
Size
(mm)
Bolt
Head
A/F
(mm)
Bonding Tail
Size
(mm2)
Pack
Size
(pcs)
HSC435
4 to 35
6 to 35
N/A
N/A
13
N/A
10
HSC435/1
4 to 35
6 to 35
800
10
13
16
10
HSC435/1O
4 to 35
6 to 35
500
12
13
16
10
HSC435/1P
4 to 35
6 to 35
300
6
13
16
20
HSC435/T
10 sq mm tail
6 to 35
240
N/A
13
N/A
10
HSCH
Gripping handle for HSC435 & HSC435/T
Relevant sections of AS4396
HSC435/1
HSC435/1O
HSC435/1P
Installation Notes:
Use only a 13mm AF, six point hexagon socket to tighten bolts.
HSC435
All other connections made on the
service and consumers cable must
also be waterproof to prevent moisture ingress through the cable into
the connector.
HSC435/T
HSCH
NEUTRAL BONDING ALTERNATIVES
Alternative products for providing for the
neutral bond.
TTD101NBKX/12
Description
Copper
Product Number Service Side Earth Tail
Tap Range
Length
(mm2)
(mm)
Lug
Hole
Size
(mm)
Bolt Head
Stainless
Steel A/F
(mm)
Pack
Size
(pcs)
TTD101NBKX
6 to 54
800
10
13
10
TTD101NBKX/12
6 to 54
500
12
13
10
SERVICE FITTINGS
CAW and CCW Series
B2
0107
The CCW and CAW series of connectors have been specially designed to provide a waterproof connection between
insulated overhead services to a variety of bare overhead mains. Both single and double tap models are available.
CAW SERIES
Mains: Bare aluminium
Service: Insulated copper or aluminium
* Piercing connector on service tap
* Complies with relevant sections of AS4396
* Disconnection of service by easy removal of
the connector from the mains
* Two tap (CAW235) model available
* Simple M8 socket operation
CCW SERIES
Mains: Bare copper
Service: Insulated copper or aluminium
* Piercing connector on service tap
* Complies with relevant sections of AS4396
* Disconnection of service by easy removal of
the connector from the mains
* Two tap (CCW235) model available
Mains Range
Product
Number
Stranding
Area
(mm2)
Service Taps
OD
(mm)
Range
(mm2)
Quantity
Pack
Size
(pcs)
Connectors for Bare Aluminium Mains
CAW35
7/1.75 to
19/3.75 Al
16 to 210
5 to 19
6 to 35
1
12
CAW235
7/1.75 to
19/3.75 Al
16 to 210
5 to 19
6 to 35
2
12
Connectors for Bare Copper Mains
CCW35
7/1.00 to
19/3.00 Cu
5.5 to 135
3 to 15
6 to 35
1
12
CCW235
7/1.00 to
19/3.00 Cu
5.5 to 135
3 to 15
6 to 35
2
10
CCW235
CCW35
Installation Notes:
Use only a 13mm AF, six point hexagon
socket to tighten bolts.
All other connections made on the service and
consumers cable must also be waterproof to
prevent moisture ingress through the cable into
the connector.
CAW35
CAW235
SERVICE FITTINGS
Mains Connection Boxes
B3
0107
Single and three phase environmental base and cover for the protection of consumer mains suitable for 6 to 35mm2
cable. Each unit contains the HSC series (House Services Connector) providing a fully sealed bimetallic connection of
copper consumer mains to Al or Cu services.
MCB SERIES - MAINS CONNECTION BOX
* Fully insulated connection system
* Plug in HSC’s providing bi-metal connection of
service cables and consumers mains
* Base suitable for rear entry of consumers mains
* Eliminates UV degradation of PVC consumers
mains
* Cover allows for easy exit of bonding tail
HSC435/1 series
* Heavy duty polyamide UV stabilised construction
* Mains box is IP66 rated
* Connectors are IP67 rated
Description
Number of
HSC435
connectors
included
Pack
Size
(pcs)
MCB1/2H
Single phase MCB supplied
with connectors
2
10
MCB3/4H
Three phase MCB supplied
with connectors
4
6
Product
Number
MCB1/2H
MCB3/4H
Use only a 13mm AF, six point hexagon socket to tighten the HSC bolts.
Recommended tool for MCB connectors: RPS13/17-6H or RPS13/17-6SH
A small flat blade screw driver is required to remove the MCB cover.
SERVICE FITTINGS
PFV Series
B4
0107
Pole or house mounted fuse holders and accessories. 100 amp single phase, “pig-tail stick” operated, service fuse for house or
pole mounting.
PFV SERIES SERVICE FUSE HOLDER
Application:
Insulated XLPE aluminium or copper cables,
Suitable for mounting on pole or house using appropriate
bracket.
Primary House Service Fuse
Features:
* Range of brackets to suit various applications including replacements
* Insulation piercing connections on line and load sides
* Insulated top mounting M8 shear head bolts
* Underside entry cable connection ports creating drip loops on
all installations
* Accepts up to 100 amp BS style cartridge (58 x 22mm)
* U.V. stabilised polymeric body with anti-flame retardant
* Can be ganged to three phases using PFBKT3 or HFBKT3
* U.V. stabilised bird guards over cable seals
* Completely waterproof bi-metallic connections.
* Stainless steel mounting bolt
* IP44 rated
Relevant sections of AS/NZS 60269
Salt fog tracking tests
Additional temperature rise tests on service cables not specified in the standard
Product
Number
Description
Cable
Range
(mm2)
Pack
Size
PFV100
Fuse Disconnector
100 amp BS style (58 x 22)
6 to 35
20
PFV100KIT
Fuse - 100 amp BS style includes
PFVAB1 adaptor bracket installed
6 to 35
12
PFV100 695
Fuse Disconnector
100 amp BS style (58 x 22)
6 to 95
ACCESSORIES
Product
Number
Description
Pack Size
PFBKT1
Pole bracket single phase
20
PFBKT3
Pole bracket three phase
15
HFBKT1
House bracket single phase
20
HFBKT3
House bracket three phase
15
PFVAB1
Adaptor bracket to fit PFV100 to
swan neck pin
40
FUSE BS100 100 amp BS Cartridge (58x22mm)
1
Installation Notes:
Use only a 13mm AF, six point hexagon socket to tighten bolts.
Do not install old copper cables when corrosion may exist.
All other connections made on the service or consumers cable
must also be waterproof to prevent moisture ingress through
the cable into the fuse holder.
PFV100
MOUNTING BRACKET OPTIONS
HFBKT3
3 phase wall
mount bracket
PFBKT1
1 phase pole
mount bracket
PFBKT3
3 phase pole
mount bracket
HFBKT1
1 phase wall
mount bracket
PFVAB1
PFV100KIT
Recommended tool for PFV100: RPS13/17-6H or RPS13/17-6SH
PRE-INSULATED FITTINGS
MJPB and MJPT Series
C1
0107
Pre-insulated compression sleeves for joining LVABC services and mains.
MJPT SERIES
* Limited and full tension 25 to 150mm2 range
* Suitable for copper or aluminium
MJPB SERIES
* Non-tension 4 to 35mm2 range
Product
Number
Service Cable
Size (mm2)
Hex Die A/F
(mm)
Pack
Size
Product
Number
Mains Cable
Size (mm2)
Hex Die A/F
(mm)
Pack
Size
MJPB4
4
4
14
10
MJPT25
25
25
17.3
10
MJPB6-4
6
4
14
10
MJPT35-25
35
25
17.3
10
MJPB6
6
6
14
10
MJPT35
35
35
17.3
10
MJPB10-6
10
6
14
10
MJPB10
10
10
14
10
MJPT50-25
50
25
17.3
10
MJPB16-6
16
6
14
10
MJPT50-35
50
35
17.3
10
MJPB16-10
16
10
14
10
MJPT50
50
50
17.3
10
MJPB16
16
16
14
10
MJPB25-6
25
6
14
10
MJPT70-35
70
35
17.3
10
MJPB25-10
25
10
14
10
MJPT70-50
70
50
17.3
10
MJPB25-16
25
16
14
10
MJPT70
70
70
17.3
10
MJPB25
25
25
14
10
**MJPT95
95
95
17.3
10
MJPB35-6
35
6
14
10
MJPB35-10
35
10
14
10
MJPT95-21
95
95
21.5
10
MJPB35-16
35
16
14
10
MJPT120
120
120
21.5
10
MJPB35-25
35
25
14
10
**MJPT150
150
150
21.5
10
MJPB35
35
35
14
10
Crimp width: 9 mm
Standard pack size: 10 pcs
** Limited tension fittings
When tested to AS3766, test load achieved is:- MJPT95SF:
7kN, MJPT95-21SF: 16.8kN
All crimps 9mm in width
Standard pack size: 10 pcs
MJPB
Recommended tool for MJPB connectors: MP-10 SIMPI
MJPT
Recommended tool for MJPT connectors:
Use any mechanical or hydraulic action crimp tool capable
of accepting 9mm wide hexagonal crimp dies, with an across
flats (AF) as specified in chart above. Minimum tonnage at
die face recommended at 5 tonne.
MP-10 SIMPI
Pre-crimped sleeve & tools
C2
0107
Pre-insulated compression sleeves with pre-crimped, PVC insulated copper tails
MJPB SERIES PRE-CRIMPED
* Non-tension 4 to 35mm2 range
Product Number
Service Cable Size
Copper or
Aluminium
(mm2 )
MJPB25-10+CABLE
25
10
None
MJPB25-10+(N)CABLE
25
10
MJPB25-16+CABLE
25
MJPB25-16+(N)CABLE
25
Pre-crimped PVC insulated copper tail
Hex Die
AF (mm)
Pack
Size
225
14
20
1 rib for neutral
identification
225
14
20
16
None
225
14
20
16
1 rib for neutral
identification
225
14
20
Size
(mm2)
Insulation Ribs Length (mm)
Crimp width: 9mm for all products
Recommended tool for all products: MP-10 SIMPI
APPLICATION TOOLING
Product Number: MP-10 SIMPI
* One-hand operation
* Specifically designed for MJPB series and other pre-insulated products
* Captive dies
* Non-hydraulic
* Hexagonal crimp AF: 14mm
* Hexagonal crimp width: 9mm
MP-10 SIMPI
Pre-crimped sleeve & tools
MEPCNA SERIES
* Pre-crimped with bare aluminium tail
* End cap on tail provided to prevent fraying
* Used for terminating LVABC into switchgear
* Used for connecting LVABC to open wire bare
conductor
C3
0107
Product
Number
Cable
Size
(mm2)
Aluminium
Tail Size
(mm2)
Die A/F
(mm)
Crimp
Width
(mm)
MEPCNA16
16
35
14.0
9
MEPCNA16-17
16
35
17.3
9
MEPCNA25
25
35
14.0
9
MEPCNA25-17
25
35
17.3
9
MEPCNA35
35
55
17.3
9
MEPCNA50
50
55
17.3
9
MEPCNA70
70
55
17.3
9
MEPCNA95*
95
75
17.3
9
100
MEPCNA150*
150
75
21.5
9
100
Pack
Size
* 75 deg C current rating: 250A
MEPCNA
MEPCNU SERIES
* Pre-crimped with bare copper tail
* End cap on tail provided to prevent fraying
* Used for terminating LVABC into switchgear
* Used for connecting LVABC to open wire bare
conductor
Product
Number
Cable
Copper Tail
Size (mm2) Size (mm2)
Die A/F
(mm)
Crimp
Width
(mm)
Pack
Size
MEPCNU16
16
35
14.0
9
MEPCNU16-17
16
35
17.3
9
MEPCNU25
25
35
14.0
9
MEPCNU25-17
25
35
17.3
9
MEPCNU35
35
55
17.3
9
MEPCNU50
50
55
17.3
9
MEPCNU70
70
55
17.3
9
MEPCNU95*
95
75
17.3
9
100
MEPCNU150**
150
75
21.5
9
50
100
*75 Deg C current rating: 250A
**75 Dec C current rating: 370A
MEPCNU
Recommended tool for MEPCNU16, MEPCNA16, MEPCNU25, MEPCNA25: MP-10 SIMPI.
All other MEPCN series products: Any compression tool with min 5t output fitted with hexagonal
compression dies as specified above.
MP-10 SIMPI
CPTAU and CPTA Series
C4
0107
A complete range of pre-insulated bi-metal and aluminium lugs for the termination of LVABC.
CPTAU SERIES BI-METALS
* Suits aluminium LVABC and other
insulated compacted aluminium
cables
* Round copper palm
* Suitable for connecting aluminium
cables to switchgear, bus bars etc.
L
Lug Dimensions (mm)
Cable
Outside
Overall
Size
Palm
Palm Hole
2
(mm ) Length (L)
Diameter
Size
(mm)
(mm)
Product
Number
Hex Die
A/F
(mm)
Die Pack
Width Size
(mm) (pcs)
CPTAU16
16
87
M10
20
14.0
9
10
CPTAU25
25
87
M10
20
14.0
9
10
CPTAU25-17
25
92
M10
25
17.0
9
10
CPTAU25-12.5DIA
25
87
M12
20
14.0
9
10
CPTAU35
35
92
M12
25
17.3
9
10
CPTAU50
50
92
M12
25
17.3
9
10
CPTAU70-21
50
115
M12
25
21.5
9
10
CPTAU95
95
92
M12
25
17.3
9
10
CPTAU95-21
95
115
M12
30
21.5
9
10
CPTAU150
150
115
M12
30
21.5
9
10
Recommended tool for up to 25 mm2: MP-10 SIMPI , larger sizes: any compression tool with min 5t output fitted with hexagonal
CPTA SERIES ALUMINIUM
*Suits aluminium LVABC and other insulated
compacted aluminium cables
* Square aluminium palm
* Suitable for connecting aluminium cables to
switchgear, bus bars etc.
W
D
Lug Dimensions (mm)
Overall
Length
(L)
(mm)
Palm
Hole
Size
Pack
Hex Die Die
Size
Palm
A/F
Width
(W x D) (mm) (mm)
(pcs)
(mm)
25
100
M12
32 x 33
14.0
9
10
CPTA35
35
110
M16
32 x 33
17.3
9
10
CPTA50
50
110
M16
32 x 33
17.3
9
10
CPTA95
95
110
M16
32 x 33
17.3
9
10
CPTA150
150
130
M16
37 x 37
21.5
9
10
Product
Number
Cable
Size
(mm2)
CPTA25
L
Recommended tool for up to 25 mm2: MP-10 SIMPI , larger sizes: any compression tool with min 5t output fitted with hexagonal
UNDERGROUND CONNECTIONS
MUCI Series
D1
0107
Multi-tap insulation piercing connectors for underground connection of two, three or four insulated cables.
MUCI SERIES SUBMERSIBLE CONNECTORS
Application:
For the waterproof, underground connection of 2, 3 or 4 cables. Suitable for copper or aluminium insulated cables, single or double insulated from 6 to 50 sq mm. Ideal for connecting cables in pillar boxes, buried connection pits and streetlight columns.
Features:
* Fully submersible and totally waterproof.
* Torque controlling shear head bolts for correct contact pressure.
* Insulation piercing on all cable taps.
* No need to strip cable.
* Flexible sealing cable ports that are not affected by the angle of cable entry.
* Fitted with push-on protective bolt caps.
* IP67 rated
Product
Number
Number
Conductor Bolt Head
of
Size
Size
Connection
(mm2)
(mm)
Ports
Pack
Size
(pcs)
MUCI4/650
4
6 to 50
13
12
MUCI3/650
3
6 to 50
13
6
MUCI2/650
2
6 to 50
13
20
MUCIBOLTYELLOW 13-17
(spare yellow
shear head bolt)
N/A
N/A
13
1
MUCI/H
Gripping handle for MUCI4/650 & MUCI2/650
Testing Specifications:
Tested to ANSI C119.1-1986
Tested to URD Pit Connector Technical Specification (Vic).
MUCI4/650
Application Notes:
Use only a 13mm AF, six point hexagon socket to tighten
bolts.
All other connections made on cables connected with this
product must also be waterproof to prevent moisture ingress
through the cable into the connector.
MUCI3/650
50 sq mm SDI may require the removal of the outer sheath,
depending on insulation thickness and conductor compaction.
The port sealing cap should be left in place when connecting
6 sq mm cables and removed for larger sizes
MUCI2/650
Cables less than 6 sq mm may be connected by doubling
over the last 2cm of cable prior to insertion. The port sealing
cap should also be left in place.
Each cable port should be only used twice. The
blue bolt must be replaced with a yellow bolt to
identify the second use of a cable port.
MUCIBOLTYELLOW 13-17
MUCI/H
Resin Filled Service Tee Joint
PRODUCT NUMBER: HSM 270/140
RESIN FILLED TEE JOINT
D2
0107
HSM 270/140
Application:
For the waterproof, underground connection of low
voltage services to low voltage mains distributor cables.
Features:
Easy to apply ‘ring’ style connector
Suitable for copper or aluminium cables
Compact, low volume joint
Suitable for direct burying
Safe, mix in the bag two part resin
No special tools required
Suitable for a wide range of popular cable types
Supplied complete with all necessary components for
one complete Tee Joint
•
•
•
•
•
•
•
•
Kit Components:
•
•
•
•
•
•
•
Multi-phase ring connector
Clear plastic encapsulating shell
Encapsulating shell sealing kit
Double chamber, mix in the bag resin system (1 bag)
Protective mixing gloves and cloth
Abrading paper
Installation instructions
To international standards
FULL SPECIFICATIONS, TEST REPORTS AND
INSTALLTION INSTRUCTIONS ARE AVAILABLE ON
REQUEST
Sealing kit
Ring Connector
Specifications - ring connector
Specification
Acceptable mains cables;
-Aluminium 4 core XLPE/PVC solid sector
-Aluminium 4 core XLPE/PVC stranded sector
(not suitable for 3 core sector cables)
Acceptable service (branch) cables;
Copper or aluminium 4 core circular
stranded:-Single service or branch
-Double service or branch
Value
6 (min) – 95 (max) mm2
6 (min) – 25 (max) mm2
Mains cable contact screw tightening torque
20 Nm
Service cable screw tightening torque
14 Nm
Tool required for tightening contact screws
5mm AF hexagonal allen
key or ‘T’ handled box
wrench. TBOX 5MM
95 (min) – 240 (max) mm2
95 (min) – 185 (max) mm2
Specifications - Completed Joint
Specification
Value
Overall dimensions of completed joint,
excluding cables
305mm (length)
140mm (width at widest point)
185mm (height)
Weight (with resin, excluding cables)
4.7 kg
Maximum overall diameter of main cable
54mm
Maximum overall diameter of service
cable
40mm
Maximum number of service cables
Two 4 core cables
Volume of resin required
3 litres (nominal)
Waste disposal
Waste packaging may be disposed of as normal landfill.
Recommended tools
Mix in the bag
resin system
TBOX 5MM
JTN/2 core separator
BF-1A and TF-2A Series
D3
0107
Mechanical connectors for use on sector shaped U/G cables.
BF & TF SERIES BI-FORM AND TRIFORM MECHANICAL CONNECTORS:
* Accepts 185 and 240mm² 4 core solid
or stranded aluminium sector cables to
AS1125.
* Accepts up to two 50mm² copper tap-off
connections. (3 for TF-2A connector)
* Available in “BI-FORM” or “TRI-FORM”
form which allows either two sector cable connections (normal loop type pillar)
or three connections (three way loop
pillar).
* Shear-head screw on main cable connections provide correct tightening of
bolts and ensure trouble free operation.
* No special tools needed for installation,
just a spanner!
* Compact dimensions allow standard
protective covers to be used.
* Fully tested to standard BS4579
“Specification for performance or mechanical and compression joints in electric cable and wire connectors” (2000
heat cycles).
Product
Number
BF-1A
BF-1A/SYD
TF-2A
TF-2A/SYD
Main Cable Range
Maximum
Tap Size
Service
Tap Stud
Size (mm)
Pack
Size
2
120 solid Al.
120 stranded Al.
240 solid Al.
240 stranded Al.
2 x 50mm²
Cu.
6
20
2
120 solid Al.
120 stranded Al.
240 solid Al.
240 stranded Al.
2 x 50mm²
Cu.
8
20
3
120 solid Al.
120 stranded Al.
240 solid Al.
240 stranded Al.
3 x 50mm²
Cu.
6
20
3
120 solid Al.
120 stranded Al.
240 solid Al.
240 stranded Al.
3 x 50mm²
Cu.
8
20
Connections
Mains
2
2
3
3
Tap
TF-2A/SYD
BF-1A/SYD
Mechanical Connectors
70
Application:
Branch connections to mains cables
Hexagonal head screw available as
an option. Add suffix ‘H’ to product
number. Eg BST/A3H
0107
Mains conductor size (mm2)
BST/A SERIES
Conductor Type:
3 or 4 core solid sector aluminium
D4
95
120
150
185
240
300
70
Branch
Conductor
Size
(mm2)
95
120
150
185
240
300
Product Numbers:
BSTA/1
All connectors
BST/A2, BSTA/3
The combinations in the table above are valid for conductors of the same
sector shape, i.e. 4 core to 4 core, or 3 core to 3 core. Should mixed
combinations be required, we suggest that verification of the products
suitability be obtained prior to use.
Packed individually in plastic bags
3/16 “ AF hex drive required
Conductor Size Range (mm2)
LVM SERIES
Product Number
Application:
General purpose branch or service
connections.
Conductor Types:
Most conductor types including solid or
stranded, circular or shaped, copper or
aluminium.
Stranded service conductors of 16
mm2 or below should be doubled and
re-doubled where necessary to
achieve a satisfactory cross sectional
area.
Overall
Width (B)
Length (A)
(mm)
(mm)
Mains / Service
Mains / Branch /
Service
LVM1
16—95
16—95
45
34
LVM2
16—185
16—185
45
44
LVM3
16—300
16—300
50
54
All connectors are electro-tinned. Brass gauze is not necessary for copper
conductors
LVM3
Shear head caps are available as an
option.
Packed individually in plastic bags
MF SERIES
Application:
Straight through joint for 3 or 4 core sector
shaped solid or stranded aluminium, and
stranded copper conductors.
Features:
All connectors feature a shear head bolt for
bolting torque control.
Pressure pads are included for stranded conductor connectors.
MF1 and MF3 types are supplied with brass
gauze for connection of copper conductors.
When connecting copper conductor, the
brass gauze supplied with connector should
be wrapped around the copper conductor
prior to bolting.
MF3 type connectors include pressure pad
for stranded side only.
Packed individually in sealed plastic bags
Product
Number
Conductor Size
Range (mm2)
D5
0107
Overall Width (B) x
Hex
Length (A) Height (C) Head AF
(mm)
(mm)
(mm)
Pack
Size
Connectors for joining STRANDED sector to STRANDED sector shaped conductors
MF1/1
50—95
80
25x25
13
1
MF1/2
95—185
100
34x33
17
1
MF1/3
185—300
120
40x41
17
1
MF1/4
300—500
120
48x51
19
1
MF1/3A
150—300
120
40x41
17
1
MF1/3G
240-240 only
120
40x41
17
1
MF1/3H
240-185 only
120
40x41
17
1
Connectors for joining SOLID sector to SOLID sector shaped conductors
MF2/1*
50—95
80
25x25
13
1
MF2/2*
95—185
100
34x33
17
1
MF2/3*
185—300
120
40x41
17
1
Connectors for joining STRANDED sector to SOLID sector shaped conductors, in
either orientation
MF3/1
50—95
80
25x25
13
1
MF3/2
95—185
100
34x33
17
1
MF3/3
185—300
120
40x41
17
1
MF3/3A
185—300
stranded
70—185 solid
120
40x41
17
1
MF3/3D
240 only
120
40x41
17
1
* MF2 types not supplied with brass gauze.
MF1 Type Connector
MF3 Type Connector
Recommended tool for all products:
RPS13/17-6H or RPS13/17-6SH
UM SERIES
Application:
Straight-through joint for 3 or 4 core sector
shaped solid or stranded aluminium, and
stranded copper conductors.
Features:
The UM series feature a removable bridge,
allowing the conductor to be easily positioned
into the connector.
All connectors feature a shear-head bolt for
bolting torque control.
Pressure pads are included for connecting
stranded conductors and should be discarded
when connecting solid core conductors.
All UM series connectors are supplied with
brass gauze for connection of copper conductors.
When connecting copper conductor, the brass
gauze supplied with connector should be
wrapped around the copper conductor prior to
bolting.
Product Number
Conductor Size
Range (mm2)
Overall
Width (A) x
Length (B) Height (C)
(mm)
(mm)
D6
0107
Hex
Head
AF
(mm)
Pack
Size
Application range for STRANDED 3 or 4 core sector shaped aluminium conductors
UM1
35—95
90
26x32
17
1
UM2
95—150
100
31x36
17
1
UM3
185—300
130
42x45
17
1
UM300
95—300
120
41x40
17
1
Application range for SOLID 3 or 4 core sector shaped aluminium conductors
UM1
70—95
90
26x32
17
1
UM2
95—150 (3 core)
95—185 (4 core)
100
31x36
17
1
UM3
185—300
130
42x45
17
1
UM300
95-300
120
41x40
17
1
Application range for STRANDED circular copper or aluminium conductors
UM1
35—95
90
26x32
17
1
UM2
95—120
100
31x36
17
1
UM3
120—300
130
42x45
17
1
UM300
95-300
120
41x40
17
1
All connectors in the series are supplied with brass gauze
MF15 SERIES CONNECTORS
WITH CENTRE BARRIER
Application:
Straight-through jointing of stranded or solid, circular or sector shaped copper or aluminium conductors. The circular profile of the connector
makes them especially suited to 11kV & 22kV
cable joints.
Features:
The MF15 series of bolted connectors feature an
integral centre moisture barrier and utilises the
patented “universal” range taking shear-head
bolts. The connector is shipped complete with
core stripping guides and brass gauze for the
jointing copper conductors.
When using these connectors in HV joints, it is
essential that the jointing system supplier’s instructions for stress relieving and re-insulation
techniques are strictly adhered to.
Product
Number
Conductor Size
Range (mm2)
Overall Diameter
Length (L)
(ΦB)
(mm)
(mm)
D7
0107
Bolt
Size
(ΦC)
Pack
Size
Application range for STRANDED SECTOR shaped conductors
MF15/1
16 to 120
95
28.5
M16
1
MF15/2
16 to 185
105
32.0
M16
1
MF15/3
70 to 300
115
37.5
M18
1
Application range for SOLID SECTOR shaped conductors
MF15/1
16 to 95
95
28.5
M16
1
MF15/2
16 to 150
105
32.0
M16
1
MF15/3
70 to 240
115
37.5
M18
1
Application range for STRANDED CIRCULAR conductors
MF15/1
16 to 120
95
28.5
M16
1
MF15/2
16 to 185
105
32.0
M16
1
MF15/3
70 to 300
115
37.5
M18
1
MF15/EDF
95 to 240
105
32.0
M16
1
Application range for SOLID CIRCULAR conductors
MF15/1
16 to 95
95
28.5
M16
1
MF15/2
16 to 150
105
32.0
M16
1
MF15/3
70 to 240
115
37.5
M18
1
Test Specifications:
ER C79
IEC 1238-1
AS/NZS 4325.1
Required tool for all products: JTS/16 Splined socket with
RPS13/17-6H or RPS13/17-6SH.
RPS13/17-6H
JTS/16
MF17 SERIES CONNECTORS
WITHOUT CENTRE BARRIER
Application:
Straight-through jointing of stranded or solid,
circular or sector shaped copper or aluminium
conductors. The circular profile of the connector
makes them especially suited to 11kV & 22kV
cable joints.
Features:
The MF17 series bolted connectors utilise the
patented “universal” range taking shear-head
bolts and comes complete with core stripping
guides.
Supplied with brass gauze for the jointing of copper conductor.
When using these connectors in HV joints, it is
essential that the jointing system supplier’s instructions for stress relieving and re-insulation
techniques are strictly adhered to.
Product
Number
Conductor Size
Range (mm2)
Overall
Diameter
Length (L)
(ΦB)
(mm)
(mm)
D8
0107
Bolt
Size
(ΦC)
Pack
Size
Application range for STRANDED SECTOR shaped conductors
MF17/1
10* to 95
90
28.5
M16
1
MF17/2
16 to 95
100
32.0
M16
1
MF17/3
70 to 300
110
35.0
M18
1
MF17/4
185 to 300
110
41.0
M18
1
Application range for SOLID SECTOR shaped conductors
MF17/1
10 to 70
90
28.5
M16
1
MF17/2
16 to 150
100
32.0
M16
1
MF17/3
70 to 240
110
35.0
M18
1
MF17/4
185 to 300
110
41.0
M18
1
Application range for STRANDED CIRCULAR conductors
MF17/1
10* to 95
90
28.5
M16
1
MF17/2
16 to 185
100
32.0
M16
1
MF17/3
70 to 300
110
35.0
M18
1
MF17/4
185 to 300
110
41.0
M18
1
Application range for SOLID CIRCULAR conductors
ER C79
IEC 1238-1
AS/NZS 4325.1
Required tool for all products: JTS/16 Splined socket with
RPS13/17-6H or RPS13/17-6SH.
MF17/1
10 to 70
90
28.5
M16
1
MF17/2
16 to 150
100
32.0
M16
1
MF17/3
70 to 240
110
35.0
M18
1
MF17/4
185 to 300
110
41.0
M18
1
*Conductor cores 10 sq mm and below should be doubled to achieve necessary cross sectional area.
JTS/16
RPS13/17-6H
ML SERIES BOLTED LUGS
Application:
Termination of stranded or solid, circular or
sector shaped, aluminium or copper cables.
Features:
* Shear-head bolts for torque control
* No specialised compression tools
required
* Supplied with brass gauze for copper conductors
D9
0107
Product
Number
Conductor
Size Range
(mm2)
Stud
Size (E)
Overall
Length
(A)
(mm)
Palm
Width
(B)
(mm)
Barrel
Height
(C)
(mm)
Pack
Size
ML1-12
50 to 95
M12
95
32.0
25.0
1
ML1-16
50 to 95
M16
95
32.0
25.0
1
ML2-12
120 to 185
M12
125
34.0
32.5
1
ML2-16
120 to 185
M16
125
34.0
32.5
1
ML3-12
240 to 300
M12
145
40.0
41.0
1
ML3-16
240 to 300
M16
145
40.0
41.0
1
ML4
400 to 500
M16
155
47.5
51.0
1
Hex head bolt AF is 17mm for all products.
BS4579, including short circuit test
ER C79
MAINS BRANCH CONNECTORS
D10
WB1, 2 & 3 SERIES - Mains to Mains Branch
Connectors
Principal Application
Conductor Range Size (mm2)
3 or 4 core stranded sector
Principal Applications
Designed to accommodate three or four core sector shaped
stranded conductors in the ranges specified in the table.
Ease of fitting and simplicity of use were fundamental objectives
adopted in the design of these connectors. The shear head screw
principle ensures that a reliable and consistent connection is
achieved without the need for specialised tooling.
Each connector is supplied in a sealed pack together with fitting
instructions, details of which are below.
0107
Product Number
Main
Weight (g)
Branch
Min.
Max.
Min.
Max.
WB1
150
300
150
300
425
WB2
300
500*
300
500*
505
WB3
300
500
150
300
490
* Sector core dimensions to BS 6791 only
Secondary Application
Stranded circular
Product Number
Main
Branch
Min.
Max.
Min.
Max.
Secondary Applications
WB1
95
240
120
300
These connectors can accept stranded circular conductors
(copper or aluminium) in the main and/or branch sides of
WB2
185
300
240
400
WB3
185
300
120
300
Physical Dimensions
For both principal and secondary applications.
Material: Aluminium Alloy
Product Number
Dimensions
A
B
C
D
WB1
82
60
67
19
WB2
93
60
72
19
WB3
91
60
68
19
Fitting Instructions - A 19mm AF hex socket is required
Separate the main cable cores sufficiently to allow yoke section to be fitted around the conductor and strip the insulation from the core equal to
the connector length plus 10mm. Thoroughly abrade the exposed conductor and loosely assemble the lower limb (mains side) of the connector
around the core by fitting the bridge piece, inserting the pressure pad and tightening the mains screws until the connector is positively located.
Set and locate the branch core, then cut to length, strip insulation to suit and thoroughly abrade the exposed conductor before assembling into
the connector as described above. Complete the operation by tightening down the mains screws consecutively, one turn at a time, until both
heads shear. Repeat the operation for the branch screws. If copper conductors are to be jointed, they should be wrapped in brass gauze in
order to improve the electrical stability of the interface connection.
MAINS BRANCH CONNECTORS
D11
WB4 Mains Branch connector
Principal application
Primarily for four core sector shaped stranded cables, in both copper
and aluminium. The branch channel designed to accept the branch
conductor in any orientation to suit any particular joint configuration.
Shear-head screws ensure that the correct clamping pressure is
applied to give reliable connection, eliminating the need for the use
of specialised tools on site.
The connector is supplied individually packed, complete with fitting
instructions, full details of which are below. Brass gauze can be
supplied upon request for use with copper conductors.
0107
Product Number
Primarily for 4 core stranded
sector
Main
WB4
Branch
Min.
Max.
Min.
Max.
150
300
185
300
410
Secondary Principal
Stranded circular
Suitable for stranded circular conductors.
Physical Dimensions
Weight
(gms)
Product Number
Material: Aluminium alloy
WB4
Main
Branch
Min.
Max.
Min.
Max.
95
240
150
300
Fitting Instructions
Separate the main cable cores to enable the main channel of the connector to be fitted around the conductor. Strip 70mm length of insulation
(connector length plus 10mm) from the core at the selected connection position.
Thoroughly abrade the exposed section of the conductor, pass the lower channel (mains side) of the connector yoke around the conductor
and loosely assemble by inserting the pressure pad and bridge piece. Tighten the screws until the connector is positively located on the main
but do not shear off the screw heads at this stage. Set the branch core and cut the required length. Strip the insulation to suit and thoroughly
abrade the exposed conductor. Assemble as for the main connection.
Complete the operation by tightening the mains screws consecutively, one quarter of a turn at a time, until both heads are sheared. Repeat the
operation for the branch side. If copper conductors are to be jointed, they should be wrapped in brass gauze before insertion into yoke.
SERVICE BRANCH CONNECTORS
D12
0107
Principal Applications
Designed to accommodate solid or stranded service conductors
Main
Branch
to a maximum of 95mm2, from four core stranded sector shaped
4 core stranded
Solid or
Product Number
mains conductors in the range 120-185mm2. The connector
sector
Stranded
employs the proven shear-head screw principal to ensure that a
consistent and reliable connection is achieved. Fitting is comMin.
Max.
Min.
Max.
pleted by the use of orthodox hand tools only. No specialised
equipment or techniques are required.
WS2
120
185
16*
95
*Note - for small section conductors see fitting instructions below
instructions, details of which are below.
160
Can accept stranded circular conductors (copper & aluminium) in the
main and/or branch sides of the connector.
Stranded circular sector conductor
Product Number
Physical Dimensions
Weight
(gms)
WS2
Main
Branch
Min.
Max.
Min.
Max.
70
120
16
70
Material: Aluminium alloy.
Separate the main cable cores sufficiently to allow the yoke section to be fitted around the conductor and strip the insulation from the core
equal to the connector length plus 10mm. Thoroughly abrade the exposed conductor and loosely assemble the connector around the core by
fitting the bridge piece, inserting the pressure pad and tightening the mains screw until the connector is positively located. Cut the branch conductor to length, strip the insulation to suit, then thoroughly abrade and assemble the core into the connector by fitting the bridge piece and
pressure pad, and tightening down the service screws to hold the conductor in position. Complete the operation by tightening down the mains
screws until the heads shears, then finally tightening the service screws consecutively, one turn at a time, until both heads are sheared.
It is suggested that conductors below the minimum range requirement of 16mm2 are doubled and, if needed, redoubled to achieve the required
cross sectional area and, if copper conductors are to be jointed, they should be wrapped in brass gauze in order to improve the electrical stability of the interface connection.
D13
Designed to accommodate solid or stranded service conductors to
a maximum of 95mm2, from four core stranded sector shaped
mains conductors in the range 120-185mm2.
The connector employs the proven shear-head screw principal to
ensure that a consistent and reliable connection is achieved. Fitting is completed by the use of orthodox hand tools only. No specialised equipment or techniques are required.
instructions, details of which are included in the technical data
below.
0107
Product Number
WS3
Main
4 core
stranded
Branch
Solid or
stranded
Min.
Max.
Min.
Max.
240
300
16*
95
Weight
(gms)
190
* Note - for small section conductors see fitting instructions below
Physical Dimensions
Product Number
WS3
Dimensions (mm)
A
B
C
D
E
66.5
40
49
13
17
equal to the connector length plus 10mm. Thoroughly abrade the exposed conductor and loosely assemble the connector around the core
screws until the heads shears, then finally tightening the service screws consecutively, one turn at a time, until both heads are sheared.
It is suggested that conductors below the minimum range requirement of 16mm2 are doubled and, if needed, redoubled to achieve the required
cross section area and, if copper conductors are to be jointed, they should be wrapped in brass gauze in order to improve the electrical stability
of the interface connection.
D14
Designed to accommodate a double service configuration to a maximum of two 95mm2 stranded conductors,
off four core stranded sector shaped mains conductors
in the range 240-300mm2.
The connector employs the proven shear-head screw
principal to ensure that a consistent and reliable connection is achieved. Fitting is completed by the use of
orthodox hand tools only. No specialised equipment of
techniques are required.
Each connector is supplied in a sealed pack together
with fitting instructions, details of which are included in
the technical data below.
0107
Product Number
Main
(4c sector stranded)
Weight (g)
Min.
Max.
Min.
Max.
240
300
2 x 50
(circ)
2 x 95
(circ)
300
95
(sector)
185
(sector)
WS4
240
(a) Single Branch Connections WS4 connector is also suitable
for single branch connections in the range 95-185mm2 (sector
shaped conductors).
(b) Circular Conductors WS4 can accept stranded circular
(aluminium or copper), in the mains and/ or branch sides.
Branch
260
Product Number
WS4
Main
(Circular)
Branch
(Circular)
Min.
Max.
Min.
Max.
120
185
1 x 50 or
2 x 50
1 x 150 or
2 x 70
Physical Dimensions
Product Number
WS4
Dimensions (mm)
A
B
C
D
E
70
50
49
17
17
equal to the connector length plus 10mm. Thoroughly abrade exposed conductor and loosely assemble the connection around the core by
screws until the head shears, then finally tightening the service screws consecutively, one turn at a time, until both heads are sheared. If copper conductors are to be jointed, they should be wrapped in brass gauze in order to improve electrical stability of the interface connection.
D15
WS5 - Mains to Service Branch
Connector
For solid or stranded sector
Designed to accommodate solid or stranded
service conductors to a maximum of 95mm2,
from four core stranded sector shaped mains
conductors in the range 400-500mm2.
The connector employs the proven shear-head
screw principal to ensure that a consistent and
reliable connection is achieved. Fitting is completed by the use of orthodox hand tools only.
No specialised equipment or techniques are
required.
Each connector is supplied in a sealed pack
together with fitting instructions, details of
which are included in the technical data below.
Product Number
Main
(4c stranded sector)
Max.
Min.
Max.
400
500
16*
95
WS5
Weight (g)
225
*Note - for small section conductors see fitting instructions below.
WS5 connector can accept stranded circular conductors (aluminium or copper) in the main and/ or
branch sides of the connector.
Material: Aluminium alloy
Product Number
WS5
Physical Dimensions
WS5
Branch
(solid or stranded)
Min.
Product Number
0107
Main
(circular)
Branch
(circular)
Min.
Max.
Min.
Max.
240
400
16
70
Dimensions (mm)
A
B
C
D
E
73
40
55
13
17
equal to the connection length plus 10mm. Thoroughly abrade expose conductor and loosely assemble the connector around the core by fitting
the bridge piece, inserting the pressure pad and tightening the mains screw until the connector is positively located. Cut the branch conductor
to length, strip the insulation to suit, then thoroughly abrade and assemble the core into the connector by fitting the bridge piece and pressure
pad, and tightening down the service screws to hold the conductors in positions. Complete the operation by tightening down the mains screws
until the head shears, then finally tightening the service screws consecutively, one turn at a time, until both heads are sheared. It is suggested
that conductors below the minimum range requirement of 16mm2 are doubled and, if needed, redoubled to achieve the required cross sectional
area and, if copper conductor are to be jointed, they should be wrapped in brass gauze in order to improve the electrical stability of the interface connection.
D16
PROTECTIVE COVERS
0107
UGT Series Underground Warning Tapes
Application:
Suitable for use in conjunction with underground
electrical services as a means of indicating its
proximity.
Features:
• Made from polyethylene
• Minimum 25mm print size on tape
• Colours comply with AS 2700
Description
Product
Number
Type / Marking
Colour
Width
(mm)
Length
(m)
Pack
Size
UGT-E
Electrical
ORANGE
150
350
1 Roll
UGT-C
Communications
WHITE
150
350
1 Roll
UGT-G
Gas
YELLOW
150
350
1 Roll
Manufactured and tested to the requirements of
AS/NZS 4275:1995.
UGT-E
Overhead Line Covers (Tigertails™)
Tested to comply with AS-4202, Class 1 insulating
covers
Product Number
TIGER TAIL DB35A
Dimensions (mm)
Length
Diameter
2600
35
Linesman Safety Covers
Tested to comply with AS-4202 Class 2 insulating material
Product Number
Underground Pit Connections Safety Cover
• Designed to fit into most commonly used distribution service pits.
• Provides an additional insulating barrier of safety for the pit connections if the main pit cover is removed or damaged.
• Provided with an eyelet for safe extraction by service personnel.
• Orange in colour, with “Danger Electricity” moulded into the unit.
Dimensions (mm)
Length
Width
LSC225
1200
225
LSC300
1200
300
LSC375
1200
375
(Illustrative Only)
TOOLS AND ACCESSORIES
E1
Spanners, testers, wedges and allen key
0107
These tools provide linesmen with a reliable means of installing all insulation piercing connectors.
Product No: RPS13/17-6H
The spanners have the following features:
* 13mm across flats and 17mm across flats in one spanner.
* Reversible ratchet.
* Suits all sizes of insulation piercing connectors (TTD and NTD) for cables
1.5mm² up to 240mm², most strain clamps and some suspension clamps.
* 6 point hex (double sided)
* Overall length 267mm
Product No: RPS13/17-6SH. Short handled version of above.
Overall length 197mm.
Product No: PPI514
Re-usable insulated cable test point. Suitable for cable ranges up to 150mm².
RPS13/17-6H
PPI514
Product No: CIE100
Core separation tool suitable for LVABC up to and including 4 x 95mm².
CIE100
Product No: PMR87
Core separation wedge suitable for LVABC up to and including 4 x 95mm².
PMR87
Product No: TBOX 5MM
T handled 5mm allen key driver, insulated handle.
Suitable for popular tee joint style ring connectors.
E2
Cutters, Strippers & Testers
0107
Product No: TOOL BAG
Linesman’s plastic tool bag
Product No: TBLVABC
Linesman’s LVABC tool kit. Includes tool bag,
RPS13/17-6H, PPI514, CIE100, PMR87 (4)
TBLVABC
TOOL BAG
Product No: RCC-42 ratchet cable cutter
Conductor range: up to 4 x 95mm2 LVABC
Ideal for cutting bundled LVABC service and mains cables.
Not suitable for high tensile steel.
Product No: CES1 & CES2
Cable end seals. Easy push on cap providing
complete waterproofing of cable ends.
Only two sizes required to cover entire range
of LVABC cables.
Cable strippers
Specially designed to strip LVABC
Product
Number
Cable
Size
(mm²)
Diameter of
Length L
cable
(mm)
(mm)
CES1
16 to 70
7.5 to 13.5
45
50
CES2
95 to 150
16.5 to 21.0
45
50
Product Number
Cable Size
(mm²)
CS095
95
CS150
150
Pack
Size
Product No: VS-MS47VH
Non contact audible, visual, vibrating voltage tester
70-600 Vac
Microwave leakage detection > 5mW/cm
Includes 4 LR44 batteries
Stringing Tools
E3
0107
Product No: 12870 Service Cable Come-along
Conductor range: 2 x 16mm2 to 4 x 35mm2
Conductor Type: LVABC
Max working load: 2kN
Failing Load: 12.5kN
Weight: 0.9kg
Product No: 12887 Service/Mains Cable Come-along
Conductor range: 2* x 25mm2 to 4 x 95mm2
Conductor Type: LVABC
Weight: 2.1kg
*additional sleeving may be required for some 2 core cables
Product No: SCBT38 Mains cable come-along
Conductor range: 4 x 95mm2
Conductor type: LVABC
Failing Load: 25kN
Weight: 3.8kg
Product No: BCCA-495150-3 Mains cable come-along
Conductor range: 4x95mm2 to 4 x 150mm2
Conductor type: Bundled LVABC
Max working load:
Failing Load:
Weight: 6.3kg
Product No: MR5341 Mains cable come-along
Conductor range: 4 x 95mm2
Failing Load: 32kN
Weight: 5.0kg
Product No: 5340 Mains cable come-along
Failing Load: 35kN
Weight: 5.0kg
Product No: 1685-31 Mains cable come-along
Failing Load: 46kN
Weight: 2.3kg
Stringing Tools
E4
0107
Product No: GRIP Service line tensioner
Failing Load: 5kN
Weight: 1.4kg
Ideal for hand stringing overhead service conductors and
other light pulling work. Use in conjunction with comealong product number 12870.
Product No: PST
Service tensioner
Product No: BR50-S Ratchet buckle and strap
Safe working load: 21.6kN
Product No: 6707BC Cable stringing block
Working load: 1134kg
Weight: 4.5kg
Sheave diameter: 178mm
Groove diameter: 53mm
Groove depth: 30mm
For complete specifications and accessories,
please call Sicame.
Product No: TOOL-LUG-ALL 30A-1300
• 1360kg max capacity
• Step reverse feature
• Complete with bag
• Light weight: 4.5kg
CABLE JOINTING TOOLS
JTN Tools
E5
0107
Insulated Core Wedge
Designed to aid the separation of cores during
jointing, these wedges are moulded in Nylon to
resist detrimental wear at the tip during normal
use. The thumb-and-finger grip assists insertion
and removal, but it’s small enough not to obstruct
work on and around the joint.
Product Number
Overall Length (mm)
Weight (g)
JTN/2
160
52
Insulated Core Separator & Wedge
Ideal for 3 core sector cables when a standard
wedge cannot be employed.
Product Number
Overall Length (mm)
Weight (g)
JTN/3
262
87
“Hepnyf” Plastic Hack-Knife
Developed for stripping the lead sheath and removal
of the bedding compound from cable. A clean cut can
be made without damage to the underlying insulation,
allowing the sheath of live cables to be safely
removed. The blade can be re-sharpened with a file.
Product Number
Overall length
(mm)
Depth of blade
(mm)
Weight (g)
JTN/4
245
39
90
Product Number: RIPPER - cable sheath remover
The all metal, multi-grip handle can be gripped outside or
inside, right & left hand. Cuts most plastic insulation cold.
Apply heat and the toughest hardest plastic cuts like butter.
Cuts any shape any direction, no limit to diameter or length.
Blade can be sharpened or replaced.
Replacement blades available.
Product Number: ORB-1 - Oxide removal brush
Painted black (for identification) for use on copper conductors to remove
copper oxide film prior to crimping of cable lugs.
Product Number: ORB-2 - Oxide removal brush
Painted white (for identification) for use on aluminium conductors to remove
aluminium oxide film prior to crimping of cable lugs.
This is a safe and efficient method for removing oxide film from conductors
Battery Powered Driver
E6
0107
Product No: SB-3UK battery powered impact socket driver
Battery powered tool especially designed for use with shear head
type bolts. Suitable for use on all Sicame products fitted with shear
head bolts.
The SB-3UK package contains:
Battery powered impact driver (1)
Nickel-metal hydride re-chargeable battery (1)
Mains (240V) powered battery charger (1)
13mm AF, six sided 1/2 inch drive socket (1)
17mm AF, six sided 1/2 inch drive socket (1)
Sturdy plastic carrying case and operating instructions
Impact Driver Specifications:
Torque:
196 Nm
Speed:
0-2,200 rpm
Motor:
14.4 Vdc
Socket drive:
1/2” square
Dimensions:
350 (L) x 180 (H) x 75 (W) mm
Weight:
2.5 kg (including battery)
Impact driver
Re-chargeable battery
Battery Specifications:
Output:
14.4 Vdc
Capacity:
3 Amp Hour
Life:
3000 charges (approx)
Charge time:
40 mins with supplied charger
Charger Specifications:
Input voltage:
240V
Capacity:
230VA
Equipped with various status indicating LED’s
240 V battery charger
Features:
∗
∗
∗
∗
∗
Fully insulated tool rated to 1000V ac, 1500 Vdc
Unique shape to reduce its length for easy access in tight spaces.
Variable speed
Well balanced and lightweight
Accepts any E-Robo series 14.4V battery
Also available as an optional extra:
12Vdc powered battery charger for
use in motor vehicles. Contact
Sicame for details.
Any other battery or powered driver must be referred to Sicame Australia for evaluation and
approval prior to use on Sicame products.
MECHANICAL FITTINGS
PA, PC AND BCST Series
PA & PC SERIES
Wedge type strain clamps
∗ PA series for higher tensions.
∗ PC series for service tensions.
∗ PC series suitable for 2, 3 and 4 core
twisted cables.
∗ Stainless steel bails on PA and PC
models.
∗ Fibreglass reinforced UV stabilised nylon.
∗ Stainless steel bails
∗ Fibreglass reinforced UV stabilised nylon.
PC63F27
Product
Number
Cable Type
Cable
Diameter
(mm)
PC63R22
Neutral
Screened
14 to 22
PC63F27
Twisted or
Flat
PC63F27A
F1
0107
No. and Size
of Cores
(mm²)
Min. Failing
Load
(kN)
Pack
Size
2.5
10
2 x 6 to 4 x 35
2.5
100
Twisted or
Flat
2 x 6 to 4 x 35
2.5
100
PC63F27B
Twisted or
Flat
2 x 6 to 4 x 35
2.5
100
PA4
Twisted or
Flat
2 x 16 to 2 x 25
6
10
PA5
Twisted or
Flat
2 x 25 to 2 x 50
14
10
PA5D
Twisted or
Flat
2 x 16 to 4 x 25
12
10
PC63F27A
PC63R22
PC63F27B
BCST Series
Bolted Type Service Strain Clamps
∗ Nylon glass reinforced clamping blocks
∗ Blocks spring loaded for ease of cable
PA4
PA5
PA5D
Product Number
Cable Size
(mm²)
Strap
Hook Style
Pack
Size
BCST-2025-3G
2 x 10 to 35
Galvanised
Open
50
BCST-4035-3G
4 x 10 to 35
Galvanised
Open
30
BCST-2025-3P
2 x 10 to 35
Nylon
Open
50
BCST-2025-3PA
2 x 10 to 35
Nylon
Closed
50
BCST-4035-3P
4 x 10 to 35
Nylon
Open
30
BCST-4035-3PA
4 x 10 to 35
Nylon
Closed
30
mounting
∗ Galvanised steel or plastic strap
∗ M10 stainless steel fastening hardware
∗ Can also be used as a suspension fitting by
rotating the clamping blocks 90 degrees
BCST-2025-3G
BCST-4035-3G
BCST-2025-3P
BCST-2025-3PA
BCST-4035-3P
BCST-4035-3PA
MECHANICAL FITTINGS
SC and PA Series
F2
0107
Suspension clamps and termination clamps for ABC mains and sub-mains.
SC SERIES SUSPENSION CLAMPS
Application:
Suspension of LVABC from 25mm2 to 150mm2
Features:
* Suitable for angles up to 30º
* 30º to 60º use PSY/H bracket
* Hinged aluminium alloy with body with stainless
steel fasteners
* Reinforced hanging eye to stop wear through
vibration
* Large angle yokes available
Product
Number
Dia. of circumscribing circle
over laid-up
cable cores
(mm)
SC435
22 to 27
SC450
27 to 30
SC470
31 to 33
SC495
SC4150
Cable Size (mm²)
2 Core
3 Core
4 Core
Pack
Size
50
35, 50
25, 35
20
50
20
70
20
37 to 40
95
20
43 to 47
150
20
95
SC495
PSY/H
158mm
PA SERIES TERMINATION CLAMPS
Application:
Termination of LVABC 2 x 25mm2 to 4
x 150mm2
Features:
* Bolted full tension clamp
* Stainless steel fasteners available as
an option
* Meets requirements of AS3560
* Removable clevis pin
Application Note:
Use fillers if only 2 cores are utilised.
Cable Size (mm²)
PA2535
2 x 25 and
4 x 25 to 35
PA10/1
2 x 25 to 50 and
4 x 25 to 50
37
6
6
PA10/1S*
2 x 25 to 50 and
4 x 25 to 50
37
6
6
PA11/1
2 x 50 to 95 and
4 x 50 to 95
43
6
6
PA11/1S*
2 x 50 to 95 and
4 x 50 to 95
43
6
6
PA122A
4 x 95 to 4 x 150
72
PA122A
Maximum Failing Load (kN)
Rated
Everyday
Tension
(kN)
Product
Number
Pack
Size
25
15
*Stainless steel fasteners
PA2535
HARDWARE
OEB, JH and QH Series
G1
0107
OPEN EYE BOLTS TO AS3766
Thread Length
Length
(L) mm
200
250
300
Product Number
16mm Dia. (D)
OEB16X250 *
-
325
OEB16X325
350
OEB16X350 *
450
OEB16X450 *
20mm Dia. (D)
150mm
Pack Size
OEB20X200
15
OEB20X250 *
15
OEB20X300
15
L
15
OEB20X350 *
-
15
15
* Preferred item in AS3766
Product No: J HOOK
J HOOK
Size: M12 to AS3766
Packed in bags of 50
Product No: J HOOK-T
J HOOK-T
J Hook with earth tag
Size: M12 to AS3766
Product No: Q HOOK
Q HOOK
Size: M12 to AS 3766
Product No: HB1
200 mm
Galvanised steel hook bracket.
Hook diameter: 16mm
To AS3766
Product No: ANG BKT
To Energy Australia
specifications
HARDWARE
Weak links and eye nuts
G2
0107
Product No: OEN M12
OEN M12
M12 eye nut to Energy Australia specifications
Product No: OEN M12 E
M12 extended eye nut to Energy Australia specifications
OEN M12 E
Product No: LFG150
1.5kN weak link to Energy Australia specifications
ABC Mechanical Weak Link
Can be installed between suspension clamp and
pole support fitting. Can also be installed between
service cable strain clamps or mains cable strain
clamps.
Mild steel galvanized to AS1650.
LFG150
Dimensions
Product Number Nominal Failing
Colour coded
Load (kN)
D (mm) L (mm) M (mm)
LFG400T
4
10
65
20
LFG600T
6
10
65
20
LFG800T
8
10
65
20
LFG800T
H1
TIME AND LIGHT CONTROLS
0107
Locking -Type Photocontrols and Delayed Response
Thermal Series
Built-in time delay prevents false cycling caused by lightning flashes
or stray headlights.
Specifications
Housing: UV stabilized high-impact polypropylene.
Photocell: 1 inch cadmium sulphide light sensitive element.
Turn-on: 1 to 3 foot-candles (10 to 30 Lux)
Turn-on/Turn-off Ratio: 1:3.
Time Delay: Minimum 15 seconds.
Switch Type: Single-pole, single-throw. Contact position at night
normally closed.
Temperature Range: -40° to 170° F.
Power Consumption: 1.1 watts average at 120 VAC.
Rated Life: 5,000 operations minimum at rated load.
All products CSA Certified.
Optional Surge Protection:
• Open Type (modified expulsion) 2.5 KV spark over minimum with
5,000 amps follow through. Add suffix “LA”.
• Enclosed Type (expulsion) 2.0 KV spark over minimum with
10,000 amps follow through. Add suffix “ELA”.
• MOV (Metal Oxide Varistor). 90 joule rating. Add suffix “MOV”
M2AF
Dimensions: 3.07” diameter, 2.15” high.
Specifications
Product Number
Voltage
Rating
Surge
Protection
Lux rating
P68275LA/20
208-277
1800VA
Open type
20
P68275LA/30
208-277
1800VA
Open Type
30
P68275MOV/20
208-277
1800VA
Metal oxide
varistor
20
P2275-2
120
1800VA
None
JP275
Accessories
M2AF
Receptacle for the above photocontrol units
JP275
Low profile cover for receptacle. Shorts line to load, keeps lights
ON at all times unless turned off from remote location.
Other models and accessories are available. Contact Sicame for details.
J1
Personal Safety
Safety Glasses
MO-11000
Stylish safety glasses made from tough polycarbonate, offering 98% UV protection. Adjustable
sides. Delivered with pouch. Clear and tinted
models available.
0107
Product Number
Description
MO-11000
Clear lenses, delivered in pouch
MO-11001
Tinted lenses, delivered in pouch
MO-11001
Safety Over-glasses
MO-11010
MO-11011
Safety glasses made from tough polycarbonate, offering 98% UV protection. Adjustable sides. Delivered with pouch.
Clear and tinted models available.
Face Shield
MO-184
Helmet not included
MO-186
Protect yourself from short circuit arcs when
working on switchboards;
• No metallic parts
• Adjustable
• Colourless 1.5mm anti-condensation, polycarbonate face shield
• Two models available, with Brow shield &
Clip-on to hardhat.
LED Headlamp
Can be worn either on the head or any
kind of helmet.
• Lighting by 3 high performance LED’s.
• 3 lighting levels.
• Adjustable lamp height angle.
• Very light, waterproof IP65.
• Range: 10 to 15 metres.
• Powered by 3 batteries LR03 (AAA).
• Battery life: 80 hours approx.
Product Number
Description
MO-11010
Clear lenses
MO-11011
Tinted lenses
Product Number
Description
MO-184
Clip onto helmet
MO-186
Brow Shield
Product Number
Description
MS-121
Delivered with batteries & carry
bag Weight: 0.09 Kg
M-95-864
Hooks set for helmet
J2
Personal Safety
1000V Insulating Gloves—Single Colour
• Tested to IEC-60903 Category M, Class 0
• Made from 1mm thick specially treated latex
• Weight: 200g
• Available in 4 sizes
• Individually tested and shipped in a sealed plastic
bag marked with test date
Product Number
Description
CG-10-A
Size 8
CG-10-B
Size 9
CG-10-C
Size 10
CG-10-D
Size 11
Leather Overgloves
• Used as outer glove.
• Silicon grain leather, very supple.
• Large protective cuff in chrome tanned hide.
• Velcro strap.
Leather Overgloves
• Used as outer glove.
• Silicon grain leather, very supple.
• Large protective cuff in chrome tanned hide.
• Velcro strap.
• Designed for use with >1000V insulating gloves
Cotton under-gloves
• To be used under insulating rubber gloves
0107
Product Number
Description
CG-98-A
8
CG-98-B
9
CG-98-C
10
CG-98-D
11
Product Number
Description
CG-99-A
8
CG-99-B
9
CG-99-C
10
CG-99-D
11
Product Number
Description
CG-80-H
Men
CG-80-F
Women
J3
Personal Safety
Rubber gloves storage box with window
• To be placed in high voltage sub-stations.
• Insulating material, shock resistant, yellow colour.
• Transparent window (ability to check gloves presence).
• Bottle of talc included.
• Attachment: 4 holes 3.5mm dia., centre distances
155x345mm.
• U.V. protective window.
Carry bag
Product Number
Overall length (mm)
Weight (g)
CG-35/1
60 x 210 x 460
0.730
Product Number
Overall length (mm)
Weight (g)
CG-36
60 x 180 x 400
0.120
• Made from reinforced waterproof fabric for
transport of rubber gloves in vehicles and
tool boxes.
• Rear loop for belt and snaps.
Insulating mats
• The matting is manufactured of elastomer compounds
with slip-resistant surface.
• High quality dielectrical rubber.
• Tested to IEC-61111.
Bags for insulating mats
• Especially designed for carrying and protecting
insulating mats.
• Equipped with a shoulder strap and a plastic window for instructions and storage identification.
Product Number
0107
Thickness (mm) Class
Voltage
(kV)
Dimensions
MP-42/11
3
3
≤ 26.5
1x1
MP-42/16
3
3
≤ 26.5
0.6 x 1
Product Number
Description
Length (cm)
MP-01
For MP-42/16 and MP-42/66
70
MP-02
For MP-42/11
110
IEC 60900 TESTED 1000V
INSULATED TOOLS
J4
0107
IEC 60900 requires that all tools comply with various dimensional standards, to ensure that the tools meet important ergonomic design principles
and are safe and easy to use. (Clause 5.3)
IMPACT
DIMENSIONS
Each type of tool is subjected to an impact test to ensure the insulation can withstand normal daily wear and tear without serious damage. Impact tests are carried out at ambient, low and extremely low temperatures. (Clause 5.4)
The dielectric test proves the integrity and performance of the
tool’s insulation. After conditioning in a water bath or wet chamDIELECTRIC STRENGTH
ber for 24 hrs, 10kV is applied for 3 minutes to the tool whilst it
is immersed. The leakage current is measured and checked for
compliance, the value of which depends on the type and size of tool.
(Clause 5.5)
INDENTATION
An indentation test is carried out to ensure the tool’s insulating properties
are retained after being subjected to a point impact. After the impact, the
insulation must withstand 5kV for 3 minutes without puncture, sparkover
or flashover. (Clause 5.6)
The adhesion test ensures that the tool’s insulating coat will not slip, move
or separate from the metal parts of the tool. After conditioning at 70 deg
C for 168 hours, the tool is allowed to cool to an ambient temperature,
then various forces are applied to test the adhesion properties and performance. (Clause 5.7)
ADHESION
Each type of tool is subjected to mechanical tests to ensure compliance with various ISO or national standards and to ensure
MECHANICAL
the tool has the necessary mechanical strength for its intended
application.
Orange, flame retardant PVC insulating outer layer with anti-slip treatment.
Tough, impact resistant, white inner insulating layer, bonded to metal
Primary adhesive layer
Finger guard bonded to tool as part of the inner insulation layer
J5
Insulated phase tester screwdriver
• Phase detection from 127V.
• Maximum voltage 1000V.
• Signalling by intermittent lighting through ultra
high intensity diode.
• Works with an un-removable lithium battery.
• 3 year battery life
Flat blade screwdrivers
• Chrome - molybdenum vanadium steel blade
Pozidriv screwdrivers
Phillips screwdrivers
0107
Product Number
Description
Weight (g)
MO-65222
Flat blade 4 x 85mm
65
Product Number
Description
Weight (g)
MO-65203
3mm blade x 100mm
33
MO-65204
3.5mm blade x 100mm
37
MO-65205
4mm blade x 100mm
46
MO-65206
5.5mm blade x 125mm
75
MO-65207
6.5mm blade x 150mm
94
MO-65209
8mm blade x 175mm
165
MO-65211
10mm blade x 200mm
195
Product Number
Description
Weight (g)
MO-65240
3mm No 0 head x 60mm
25
MO-65242
4.5mm No 1 head x 80mm
50
MO-65244
75
MO-65246
150
MO-65248
230
Product Number
Description
Weight (g)
MO-65230
25
MO-65232
4.5mm No 1 head x 80mm
50
MO-65234
75
MO-65236
150
MO-65238
230
J6
Universal pliers
• Special tool steel, oil hardened.
• Burnished head
0107
Product Number
Overall length (mm)
Weight (g)
MO-66001
160
210
MO-66002
180
260
MO-66003
200
300
MO-66005*
250
510
Product Number
Overall length (mm)
Weight (g)
MO-66300
145
115
MO-66302
160
160
Product Number
Overall length (mm)
Weight (g)
MO-66202
160
150
* For steel armoured cable
Flat nose pliers
• Burnished head
Round nose pliers
• Burnished head
Bent snipe nose pliers
• Chrome-vanadium steel.
• Burnished head
Product Number
Overall length (mm)
Weight (g)
MO-66402
160
160
MO-66404
200
185
J7
Long nose pliers with side cutter
• Burnished head
Plug pliers for pre-insulated pin terminals
• Chrome-vanadium steel for 2.8, 5 , 6.35mm pin
terminals.
0107
Product Number
Overall length (mm)
Weight (g)
MO-66102
160
145
Product Number
Overall length (mm)
Weight (g)
MO-66105
200
200
Waterpump pliers
• Burnished head
Product Number Overall length (mm)
MO-66502
250
Weight (g)
410
Standard type
MO-66505
250
Weight (g)
405
Box joint pliers
Side cutters
• Special carbon steel.
• Oil hardened.
• Burnished head.
Cutting capacity (mm)
Weight (g)
Soft 80Kg/mm2
Hard 140Kg/ mm2
Ø1
150
MO-67101
140
Ø2
MO-67102
160
Ø 2.5
Ø 1.5
180
MO-67103
180
Ø3
Ø 2.5
210
J8
End cutting pliers
• Special carbon steel.
• Oil hardened.
• Burnished head.
MO-67401, MO-67402
Cable cutter
• Chrome-vanadium.
• Forged steel.
Cable cutters
• Chrome-vanadium.
• Forged steel.
• Oil-hardened.
MO-67501
Ratchet cable cutters
• For copper and aluminium cables only.
• Treated forged steel blade.
MO-67599
0107
Weight (g)
Soft
80Kg/mm2
Hard
140Kg/mm2
MO-67401
140
Ø1
Ø2
165
MO-67402
160
Ø2
Ø3
210
MO-67404
200
Ø3
Ø4
450
MO-67404
Product Number
Overall length (mm)
Weight (g)
MO-67500
170
Maximum Ø 4
420
Weight (g)
MO-67501
170
Maximum Ø 15
285
MO-67502
230
Maximum Ø 20
520
MO-67502
Product Number
Cutting capacity (max)
Weight (g)
MO-67599
Ø 32mm/ 180mm2 Cu 250mm2 Al
900
MO-67600
950
MO-67601
975
MO-67601
J9
Parrot beak style cable cutter
Product Number
Cutting capacity
Weight (g)
MO-67611
790
• For copper and aluminium only.
• Treated forged steel blade.
Hacksaw
• Protected hard forged steel.
• Two blade positions.
• Flushed and 90º cutting angle.
• Delivered with 2 blades.
Stripping pliers for L.V. cables
• Aluminium casting plier.
• To strip L.V. twisted cables.
• Blade depth adjustable.
• For use on LVABC cable.
Stripping pliers for L.V. cables
• Aluminium casting plier.
• To strip L.V. cables.
• Blade depth adjustable.
• For use on LVABC cable.
0107
Product Number Blade length (mm)
Overall length (mm)
Weight (g)
300
450
780
Product Number
Overall length (mm)
Stripping capacity
Weight (g)
MO-67304
220
from 16 to 150mm2
470
MO-64502
Product Number
Overall length (mm)
Stripping capacity (mm2)
Weight (g)
MO-67305
265
From 16 to 150
650
MO-67306
270
From 50 to 240
670
J10
Wire stripping pliers
• Chrome vanadium.
• Burnished head.
Stripping knifes
• Delivered with pouch.
Adjustable spanner
• Special tool steel.
• Oil hardened.
0107
MO-67302
160
Capacity (mm2)
Weight (g)
0.6 to 10
170
Product Number
Blade length (mm)
Overall length (mm)
Weight (g)
MO-61001
62 (Straight)
190
110
MO-61002
50 (Curve)
190
110
Maximum capacity (mm)
Weight (g)
MO-69002
210
24
295
MO-69003
250
28
450
MO-69004
310
34
550
MO-69005
385
43
1350
J11
Reversible hexagonal ratchet handle
• Special tool steel.
• Oil hardened.
Combination wrench
Product Number
• Special steel sockets.
Product Number
AF (mm)
Weight (g)
MO-69210
10
160
MO-69213
13
190
MO-69216
16
350
MO-69217
17
370
MO-69218
18
380
MO-69219
19
390
4 hexagonal sockets
Length (mm)
MO-68702
8-10-12-14
150x150mm
260
MO-68703
7-9-11-13
150x150mm
250
MO-68704
8-10-13-17
150x150mm
260
Product Number
B
A
Weight (g)
AF Sizes (mm)
Right angle hexagonal key wrench
0107
Hexagonal head (mm)
Weight (g)
AF
A
B
MO-69903
3
83
123
30
MO-69904
4
84
124
40
MO-69905
5
84
126
50
MO-69906
6
86
126
70
MO-69908
8
87
128
110
MO-69910
10
87
130
150
MO-69912
12
90
132
240
J12
Open end spanners.
Product Number
AF (mm)
Weight (g)
Product Number
AF (mm)
Weight (g)
MO-68008
8
40
MO-68020
20
185
MO-68009
9
40
MO-68021
21
200
MO-68010
10
45
MO-68022
22
220
MO-68011
11
50
MO-68023
23
250
MO-68012
12
60
MO-68024
24
260
MO-68013
13
80
MO-68025
25
280
MO-68014
14
100
MO-68026
26
300
MO-68015
15
110
MO-68027
27
340
MO-68016
16
120
MO-68028
28
360
MO-68017
17
140
MO-68029
29
400
MO-68018
18
160
MO-68030
30
500
MO-68019
19
170
MO-68032
32
570
Spanner Sets
Cranked ring wrench
0107
Product Number
Description
Weight (g)
MO-68008/19
Open end spanner set including
8, 10, 11, 12, 13, 14, 17, 19mm AF spanners
685
Product Number
AF (mm)
Weight (g)
Product Number
AF (mm)
Weight (g)
MO-68107
7
35
MO-68120
20
240
MO-68108
8
40
MO-68121
21
260
MO-68109
9
45
MO-68122
22
260
MO-68110
10
50
MO-68123
23
270
MO-68111
11
65
MO-68124
24
280
MO-68112
12
80
MO-68125
25
300
MO-68113
13
100
MO-68126
26
360
MO-68114
14
120
MO-68127
27
400
MO-68115
15
150
MO-68128
28
440
MO-68116
16
180
MO-68129
29
480
MO-68117
17
190
MO-68130
30
500
MO-68118
18
195
MO-68132
32
540
MO-68119
19
200
J13
Hexagonal spanner with T handle
Product Number
AF (mm)
Weight (g)
MO-68610
10
145
MO-68613
13
185
MO-68614
14
220
• Chrome steel.
• Length 130mm
1/4” sockets wrench sets
• Chrome steel.
MO-69840/17
Insulated Tool Kits
0107
Product Number
Description
Weight (g)
MO-69813
Socket 13mm AF - 1/4” drive
45
MO-69317
Socket 17mm AF - 3/8” drive
60
MO-69840
Extension 1/4” AF x 3/8” drive
60
MO-69512
Reversible ratchet - 1/4” drive
200
MO-69813/ 17
Complete socket set in plastic
box 230 x 170 x 45
365
Product Number
Description
Weight (g)
MO-69810
Socket 10mm - 1/4”
35
MO-69813
45
MO-69317
60
MO-69840
Extension 1/4” - 3/8”
60
MO-69512
Reversible ratchet - 1/4”
200
MO-69810/17
Complete socket set in plastic
box 230 x 170 x 45
500
Product Number
• For most common operations
Description
MO-65242 - Pozidriv screwdriver* No 1 4.5 x 80mm
MO-65244 - Pozidriv screwdriver* No 2 6 x 100mm
KIT 03
MO-65204 - Flat blade screwdriver 3.5 x 100mm
MO-65206 - Flat blade screwdriver 5.5 x 125mm
MO-65209 - Flat blade screwdriver 8 x 175mm
J14
0107
3/8” & 1/2” drive sockets, sets and accessories
• Chrome steel.
Sockets 1/2” drive - 12 sided
Sockets 3/8” drive - 6 sided
Product Number
Description
Weight (g)
Product Number
Description
Weight (g)
MO-69306
6mm AF socket
25
MO-69408*
8mm AF socket
60
MO-69307
7mm AF socket
30
MO-69410*
10mm AF socket
60
MO-69308*
8mm AF socket
30
MO-69411
11mm AF socket
60
MO-69309
9mm AF socket
30
MO-69412*
12mm AF socket
70
MO-69310*
10mm AF socket
35
MO-69413*
13mm AF socket
70
MO-69311
11mm AF socket
35
MO-69414*
14mm AF socket
70
MO-69312*
12mm AF socket
35
MO-69415
15mm AF socket
75
MO-69313*
13mm AF socket
45
MO-69416
16mm AF socket
75
MO-69314*
14mm AF socket
45
MO-69417
17mm AF socket
80
MO-69315
15mm AF socket
50
MO-69418
18mm AF socket
80
MO-69316
16mm AF socket
55
MO-69419*
19mm AF socket
85
MO-69317*
17mm AF socket
60
MO-69420
20mm AF socket
90
MO-69318
18mm AF socket
65
MO-69421*
21mm AF socket
100
MO-69319*
19mm AF socket
70
MO-69422*
22mm AF socket
100
MO-69321*
21mm AF socket
85
MO-69423*
23mm AF socket
115
MO-69322*
22mm AF socket
90
MO-69424
24mm AF socket
130
MO-69323
23mm AF socket
100
MO-69430
30mm AF socket
160
MO-69513*
Reversible ratchet
600
MO-69514*
Reversible ratchet
600
MO-69523*
130mm extension
124
MO-69524*
125mm extension
250
MO-69533
250mm extension
270
MO-69534
250mm T wrench
435
MO-69542
130mm T wrench
220
MO-69544
300mm T wrench
520
MO-69543
200mm T wrench
380
MO-69408/ 23
Socket set comprising
items marked * in plastic
box 410 x 120 x 75
1500
MO-69308/ 23
Socket set comprising
items marked * in plastic box 410 x 120 x 75
1250
* Sockets composing the sets
* Sockets composing the sets
MO-69524
MO-69543
MO-69308/23
J15
Long series sockets, 3/8” drive
• Chrome steel.
• 65mm length
U.S Standard sockets, 3/8” drive
• Chrome steel.
6 sided male hex key socket, 3/8” drive
• Tool steel.
Insulated torque wrench, 3/8” drive
• Capacity: 8 to 54 Nm (ibF Ft: 5-40).
• Length: 325mm
• Tolerance: 4%
0107
Product Number
AF (mm)
Weight (g)
MO-69610
10
75
MO-69613
13
80
MO-69614
14
100
MO-69616
16
115
MO-69617
17
125
MO-69618
18
140
MO-69619
19
160
MO-69621
21
190
Product Number
AF (mm)
Weight (g)
MO-69735
3/8”
25
MO-69736
7/16”
30
MO-69737
1/2”
35
MO-69738
9/16”
35
MO-69739
5/8”
42
MO-69740
11/16”
50
MO-69741
3/4”
55
MO-69742
13/16”
60
Product Number
AF (mm)
Weight (g)
MO-69393
3
45
MO-69394
4
55
MO-69395
5
60
MO-69396
6
65
MO-69397
7
70
MO-69398
8
70
Product Number
Description
Weight (g)
MO-69050
8 to 54 Nm
790
J16
0107
Contractors Tool bag
Product No: M-87370
y For intervention works
y Strong waterproof, canvas reinforced bottom
y Large capacity of storage with shoulder strap
Contractors 1000V Insulated Tool Kit
Product No: TKC - 1000V -1
y Complete equipment requirements for level 2 service providers
y Tool bag included
y Tool kit comprises of the following items
Tools Continue
Product Number
Description
Product Number
Description
Personnel Equipment
MO-68019
1 open ended spanner 19mm
MO-11001
1 pair safety glasses
MO-68113
1 ring spanner 13mm
CG-98-*
1 pair working gloves
MO-68117
1 ring spanner 17mm
CG-80-H
1 pair cotton under-gloves
MO-68119
1 ring spanner 19mm
Insulating Gloves & Accessories
MO-69003
Adjustable wrench
MO-69413
1 1/2” drive-12 sided socket 13mm
MO-69417
MO-69419
MO-69514
1 1/2” reverse ratchet
MO-69524
1 1/2” 125mm Ext bar
CG-10-*
1 pair 1000v insulated gloves
CG-36
1 carry bag for insulated gloves
Insulated tools
MO-61001
1 stripping knife (curved blade)
MO-65203
1 flat blade screwdriver 3x100mm
MO-65206
1 flat blade screwdriver 5.5x125mm
MO-65209
1 flat blade screwdriver 8x175mm
MO-65222
1 phase tester screwdriver 4x85mm
MO-65230
1 Phillips screwdriver N0 0
MO-65234
MO-65238
MO-66003
1 universal pliers 200mm
MO-66102
1 long nose pliers 160mm
MO-67103
1 side cutter 180mm
MO-68013
MO-68017
* Gloves available in 4 sizes A=8, B=9, C=10 & D=11
EARTH SYSTEMS
K1
Accessories
Clamp Removal Arm (Pigtail)
Used for removing MT-613/3 snap-on clamps from overhead lines
Available in 3 different fittings
Normally sold with MT-630 clamp application platform (refer below)
CRA/K
CRA/S
CRA/C
Clamp Application Platform
Used for attaching MT-613/3 snap-on clamps onto overhead lines.
Normally sold with CRA clamp removal arm (Pigtail). (see above)
0107
Product Number
Description
CRA-C
“C” - Hexagon fitting
CRA-K
“K” - Universal fitting
CRA-S
“S” - Shotgun fitting
Product Number
Description
MT-630-C
MT-630-K
MT-630-S
Product Number
Description
FRA-C
FRA-K
MT-630-K
MT-630-C
Fuse Remover Adaptor
Used to remove drop-out fuses
FRA-C
FRA-K
Drop-Out Fuse Earthing Adaptor
Product Number
Used for providing an earthing point on the bottom of
drop out fuse carriers where conductors from drop out
fuses to transformers are fully insulated.
DOFEA
Product No: DOFEA
Link adaptor
Used for attaching and removing drop-out
fuses prior to applying a DOFEA.
LKA/C
LKA/S
Product Number
Description
LKA/C
LKA/K
LKA/S
LKA/K
EARTH SYSTEMS
K2
Accessories
Mines Discharge Sticks
Product Number
Description
MDS/2
Mines Discharge Stick with Standard with 2 m lead
Handle length: 1 m
MDS/2 EXT
Mines Discharge Stick with Standard with 2 m lead &
extended nipple Handle length: 1 m
MDS/3
Mines Discharge Stick with Standard 3 m lead
Handle length: 1 m
Used to discharge underground
cables prior to being earthed.
MDS/2
MDS/2 Ext
0107
MOD/E
Modiwark Adaptor
Used for holding Modiwark type voltage detectors on
the end of a high voltage stick.
MOD/C
MOD/K
MOD/S
Live Line Clamp Remover
Fits onto a high voltage stick and is used
for removing live line clamps.
Product Number
Description
MOD-C
MOD-K
MOD-S
MOD-E
“E” - Bayonet fitting
Product Number
Description
LLCR-C
LLCR-K
LLCR-S
LLCR/K
LLCR/C
LLCR/S
Service Fuse Puller
Used for pulling services fuses on poles/houses.
Product Number
Description
SFP-C
SFP-K
SFP/K
SFP/C
EARTH SYSTEMS
K3
Accessories
Fixed Earth Connection Point
An earthing point used in substations & switchrooms.
Includes Bolts & Washers.
Two diameters are available - 22mm and
25mm
0107
Product Number
Rating
(kA)
Diameter
(mm)
Stub Diameter
(mm)
M12/22 BRS STUB
25kA/0.5 secs
12mm
22mm
M12/25 BRS STUB
25kA/0.5 secs
12mm
25mm
M16/22 BRS STUB
45kA/0.5 secs
16mm
22mm
M16/25 BRS STUB
45kA/0.5 secs
16mm
25mm
M12/22 BRS STUB
Voltage Detector Extension Probe
Extension probe which fits voltage detector
type CC-875 for testing insulated switchgear.
Product No: PROBE KSA/875
Manoeuvering Hook
Product Number
Description
PROBE KSA/875
Length - 440mm
Diameter - 20mm
Product Number
Description
CM-02-C
CM-02-K
Bronze-Copper nickel aluminium
Weight : 0.120Kg
Available in two different fittings
CM-02-C
Product Number
Description
POLE SAFETY STEPS
Safety pole steps with washer
Product Number
Description
CASE EX LGE
Inside Dim 485x355x186mm
CASE LGE
CASE MED
Product No: POLE SAFETY STEPS
Equipment Boxes
Ideal for storage & transport of high
voltage detectors, accessories & other
instruments.
Watertight, shock & vibration proof and
also dust proof
Complete with foam inserts
EARTH SYSTEMS
K4
Accessories
0107
Connection adaptors for insulating sticks
K
C
E
Universal
Hexagonal
Bayonet
C
A or B
Clamp - Stick
“MAJOR” Serie
CM-4/ CM-6/ CM-7
K
E
Connection
Adaptors
Accessories
S
CI-6-C
CI-5-C
CI-3-K
S
AB
CI-4-K
CI-6-K
CI-7-K
K
E
CI-5-K
CI-3-E
CI-7-E
CI-4-E
AB
K
C
Sticks
CI-7-C CI-3-C
E
AB
K
C
S
With this range, any accessory can be attached to any stick by using
connection adaptors. For other models, please consult us.
CI-6-C
CI-4-E
CI-7-E
CI-5-C
CI-4-K
CI-7-K
CI-5-C
CI-3-C
CI-7-C
CI-5-K
End Cap for CI-3-C
CI-6-K
EARTH SYSTEMS
K5
Accessories
Clamp Application Handle
0107
Product Number
Description
HEC-250-E
Length - 340mm
Small PVC handle to apply Bayonet type
earth clamps.
Product No: HEC-250-E
Stick Adaptor
To connect Ergon sticks with
hexagonal “C” fittings.
Product Number
Description
CAPALEC ADAPTOR
Length - 210mm
Product No: CAPALEC ADAPTOR
Stick Adaptor
To connect Integral sticks to universal
head tools or hexagonal “C” fittings.
Available in 2 different fittings.
Product Number
Description
IATH-C
Length - 150mm
IATH-K
Length - 200mm
P/N: IATH-K
P/N: IATH-C
Stick Adaptor
To connect SECV/C sticks with hexagonal
“C” fittings.
Product Number
Description
SECV/C
SECV to C adaptor
Length - 230mm
EARTH SYSTEMS
K6
Accessories
Conductor Brushes
0107
Product Number
Description
MG-206-AK
Moulded red colour body with card.
Reserved for aluminium conductors
MG-206-CK
Moulded red colour body with card.
Reserved for copper conductors.
Pivoting - 95 x 90 x 64mm
Weight : 0.090Kg
Universal head
Conductor Brushes
Product Number
Description
MG-352-K
Moulded orange colour body with card.
Reserved for aluminium conductors
MG-352-VK
Moulded green colour body with card.
Reserved for copper conductors.
MG-353-R
Orange spare brush for MG-353-K.
For hand brushing use.
MG-353-V
Green spare brush for MG-353-K.
For hand brushing use.
MG-354-K
Round brush - Ø 58 x 100mm
Weight: 0.250 Kg
MG-355
Spare brush for MG-354-K
Pivoting - 110 x 110 x 70mm
Weight : 0.250Kg
MG-354-K
Diameter Measuring Gauge
Product Number
Conductor range 3 to 16mm Ø.
Entirely insulated material 270 x 35 x 12mm
Weight: 0.090 Kg
Rising Sun’ fitting
Delivered in bag
Cleaning Brushes
MD-535-K
Product Number
Description
MD-10-C
Concave brush with two rows of perpendicular bristles
100 x 125 x 170mm - Weight: 0.500Kg
MD-12-C
Round head brush
Ø 175 x 228mm - Weight: 0.500Kg
MD-14-C
Adjustable hinged round head brush
Ø 175 x 328mm - Weight: 0.500Kg
Hex fitting
MD-14-C
MD-12-C
MD-10-C
EARTH SYSTEMS
K7
Clamps
Application Handle
0107
Product Number
Description
815S/H
Handle
Length - 320mm
Used to tighten MT-815-S clamps
onto earth connections.
Hand Applied Earth Clamps
For connection of MT-192-E clamps
to fixed earthing points.
Product Number
Description
MT-1921E H
Earth Clamp with PVC Handle
Length - 350mm
P/N: MT-1921E H
Fixed Points
Used for providing earthing points in
substations/ switchrooms and flat
conductors
Commonly used with MT-1921-E
earth clamps (refer to above)
Product
Number
Rating
(kA)
Sphere
Dimension
Weight
(g)
Fixing
MT-3951
25kA/0.5 sec
Ø 25mm
240
Thread: M12
MT-3952
45kA/0.5 sec
Ø 25mm
240
Thread: M16
MT-3951/1
Ø 25mm
300
Bolt: M12 - L = 45mm
MT-3952/1
Ø 25mm
350
MT-3950/35*
Ø 25mm
300
* = Not IEC
P/N: MT-3951
MT-3952
P/N:
MT-3950/35
P/N: MT-3951/1
MT-3952/1
CARRY BAGS
K8
Earths Set & Stick Bags
Earth Set Carry Bags
ARB/500
Stick Carry Bags
ARB/S115
ARB/S415
Product Number
0107
Description
BAG PVC ARB/454
Carry Bag 400 x 500 x 400 + Zipper
BAG PVC ARB/500
Carry Bag 500 x 500 x 150
BAG PVC ARB/501
Carry Bag 500 x 500 x 150 + 1 Divider
BAG PVC ARB/502
BAG PVC ARB/600
BAG PVC ARB/601
BAG PVC ARB/602
BAG PVC ARB/700
BAG PVC ARB/762
Carry Bag 700 x 600 x 200 + Zipper
Product Number
Description
BAG PVC ARB/MDS
AES-MDS Stick Carry Bag
BAG PVC ARB/S110
1 x 1.0 Mt Stick Carry Bag
BAG PVC ARB/S115
BAG PVC ARB/S120
BAG PVC ARB/S125
BAG PVC ARB/S130
BAG PVC ARB/S210
BAG PVC ARB/S215
BAG PVC ARB/S220
BAG PVC ARB/S310
BAG PVC ARB/S315
BAG PVC ARB/S320
BAG PVC ARB/S410
BAG PVC ARB/S415
BAG PVC ARB/S420
BAG PVC ARB/S510
BAG PVC ARB/S515
BAG PVC ARB/520
BAG Extra Pockets
Extra Pockets /P or /A for Adaptors etc..
LANYARDS & SANDBAGS
Lanyard for MT-701/1 Clamps
8mm Megalon insulated
Used for applying CATU clamp MT-701/1 onto overhead wires.
Sandbags
Used with Megalon lanyards (see above) to
hoist MT-701/1 clamps onto conductors.
Link
K9
0107
Product Number
Length
(Mt)
LANYARD 08M
8
LANYARD 09M
9
LANYARD 10M
10
LANYARD 11M
11
LANYARD 12M
12
LANYARD 13M
13
LANYARD 14M
14
LANYARD 15M
15
LANYARD 16M
16
LANYARD 17M
17
LANYARD 18M
18
LANYARD 19M
19
LANYARD 20M
20
LANYARD 21M
21
LANYARD 22M
22
LANYARD 23M
23
LANYARD 24M
24
LANYARD 25M
25
LANYARD 30M
30
LANYARD 35M
35
LANYARD 40M
40
LANYARD 45M
45
LANYARD 50M
50
Product Number
Description
SANDBAG ASSEMBLY
Sandbag with link & sister clip
SANDBAG W/LOOP
Bag with sand & carry loop
Sister clip
P/N: SAND W/LOOP
P/N: SANDBAG ASSEMBLY

Sicame Australia - Australian Powerline Industries

Transcription

Similar documents

Cellofoam`s PERMACOOL® Shippers

Hajoca Corporation

FIRST CORP INTERNATIONAL, INC CREDIT APPLICATION

Checkliste Freifläche_en

- Included with Park Millennium Cable TV Package

Scanned Document

www.alubond.com Aluminium composite panels for facade cladding

realdeals - Realcold

SPECIALTY GLASS - OBSCURE glaztech.com - Glaz

SNAP-TITE spec sheet