Marley PVC Foam Fascia and Barge Board

Marley PVC Foam Fascia and Barge Board Complete system
Made from superior formulated uPVC foam utilising the latest technology.
The molecular structure of the board’s core makes it extremely lightweight
yet surprisingly tough, whilst the outer skin of the board provides rigidity,
durability and a high quality maintenance-free finish. Superior in many
ways to traditional materials such as wood and fibre cement, Marley’s Fascia and Barge Boards offer many advantages
•
•
•
•
•
•
•
•
•
•
Solid Brass Screws and Cover Caps allow for corrosion free installation with professional finish
No special tools required
The Fascia and Barge Boards are packaged in a protective film to
prevent scratches before installation
A simple instruction sheet can be peeled off post installation
These products are denser to ensure durability
UV inhibitors offering Ultra Violet Protection
Scratch-free finish
Extruded in long lengths to assist with easy installation
Easy to transport
No water absorption
Advantages Over Traditional Materials
•
•
•
•
•
•
•
•
•
•
•
Lightweight cellular construction makes for easier, quicker, safer installation
Rigid PVC outer skin results in high impact resistance
Titanium treated surface means UV stability offering Ultra Violet Protection
Colourfast appearance
Flat surface with a thick top layer and high gloss need never be painted
Maintenance free design means easy cleaning with warm soapy water
Material is resistant to insects and vermin and cannot rot
Fascia and barge boards are non-flammable so will therefore not
Fittings
support combustion
Attractive profiles add style to your home
•
End caps available to finish off the product
Cellular structure absorbs expansion in extreme heat, minimising •
Screw packs included
expansion allowances
Solid Fascia Board structure will support gutter brackets
Fascia and Barge Board Step by Step Installation Guide
1
Fascia Board Dimentions :
Barge Board Dimentions :
Width: 225m
Length: 4m & 6m
Thickness: 9mm
Mass/m: 1.36kg
Average Density: 0.55g/cm3
Width: 225m
Length: 4m & 6m
Thickness: 9mm
Mass/m: 1.70 kg
Average Density: 0.55g/cm3
2
Remove existing Fascia and Carefully measure the reBarge Boards, or any other
quired length of fascia.
material interfering with the
installation. Take care not to
damage the rafter ends, and
repair if already damaged or
rotten.
5
Attach the fascia board
with the solid brass screws
supplied. There is no need
to pre-drill a hole. If using a
power driver set the torque
on the lower level to avoid
snapping the screw head.
9
6
Repeat the process for the
next board.
10
Exactly the same installation The joining connectors for the
Barge Boards work the same
procedure is used for the
as the Fascia Connectors.
Barge Boards. Ensure you
cut the ends of your Barge
Board vertically.
Visit www.marleypipesystems.co.za for more information or to
locate your nearest stockist or call us on +27 (0)11 739 8600
3
Transfer measurements onto
the fascia to be cut. Always
mark the fascia on the inside
(dull side).
7
If the length of the required
fascia means you have to
join boards, make sure you
measure from the inside of
the connectors on either side
of the gap you intend filling.
Cut to size, then snap into
place.
11
At the apex of the roof join
the boards with a vertical cut.
Use a plumb line if you need
assistance. You can choose
to fill any gaps in this join with
white Silicon, but no seal is
required.
4
Cut the fascia to the required
length using a hacksaw or
any saw with a fine blade.
Do not use a cutting disc or
grinder for this job.
8
When deciding where to position the joining connectors,
try to centre an odd number
of joints, and if possible make
each fascia board length the
same.
12
Your Fascia and Barge
Boards are guaranteed for 10
years, require no painting and
no maintenance.