InstructIon Manual conVErtIBlE BoostEr sEat - Maxi-Cosi

Instruction Manual
CONVERTIBLE Booster seat
MODEL
GMA 2010 & GM 2010
For toddler use with built in
harness (6 months to 4 years
approximately)
As a booster seat with
lap-sash seat belt (4 years to
approximately 6 to 8 years)
Illustrations are representative only.
Design and style may vary.
IMPORTANT: KEEP THIS BOOKLET IN THE POCKET
PROVIDED AT THE REAR OF THE CHILD RESTRAINT
Before You Start
Thank you for purchasing this child seat. This product is suitable
for toddlers and older children. We welcome you as a valued
customer, and trust that your child will enjoy many years of comfort
and safety.
No child restraint can guarantee absolute protection from a crash.
However proper use of this restraint may reduce the risk of injury or
death!
Table of Contents
Page
Page Page
3 - 5 Warnings
6 Warnings To Parents And Other Users
7 - 10 Anchorage Fitting Installation
Page 11 Correct Vehicle Position
Page 12 Tether Strap / Headrest Adjustments
Page 13 Reclining Backrest
Page 14 - 15 Features For Toddler Mode
Page 16 - 20 Preparation For Use Toddler
Page
21 Correct Shoulder Height Marker
Page 22 - 23 Features For Booster Mode
Page
24 Remove Harness System
Page 25 - 26 Installation For Booster Mode
Page
27 The next seat for your child
Page 28 - 31 Care And Maintenance
2
WarnInG
IMPORTANT: RETAIN FOR FUTURE REFERENCE
THESE INSTRUCTIONS DETAIL THE SAFE USE, FITMENT AND
MAINTENANCE OF THE SEAT.
PLEASE READ THESE INSTRUCTIONS CAREFULLY AND
ENSURE THAT THEY ARE FOLLOWED AT ALL TIMES.
NO SAFETY SEAT CAN GUARANTEE PROTECTION FROM
INJURY HOWEVER, PROPER USE OF THIS SEAT REDUCES
THE RISK OF SERIOUS INJURY OR DEATH TO YOUR CHILD.
THIS RESTRAINT MUST BE ATTACHED TO A CHILD RESTRAINT
ANCHORAGE POINT IN THE CAR. REFER TO CAR OWNER’S
HANDBOOK FOR LOCATION OF ANCHORAGE POINTS.
REFER TO A CHILD RESTRAINT FITTING STATION IF NO
ANCHORAGE POINTS ARE IN THE MOTOR CAR.
Follow the manufacturer’s instructions at all times.
Use the restraint exactly as shown in the instructions.
To be used in forward-facing position by children whose shoulders
are above the lower shoulder height marker (approximately 6
months of age) until their shoulders reach the middle shoulder
height marker (approximately 4 years of age). Then to be used with
a lap-sash seatbelt until their shoulders reach the upper shoulder
height marker (approximately 6 to 8 years of age).
Continue to use this child restraint until the child reaches this limit.
Children are safest in a booster seat until their shoulders reach the
upper shoulder height marker of the booster seat.
Do not use this restraint until child’s shoulders are above the lower
shoulder height marker. Just using a seatbelt is not recommended
for children that have outgrown this seat. Use a larger booster seat.
3
WarnInG
General
• Supervision of children is needed because they may be able to undo buckles.
• Use the restraint exactly as shown in the instructions.
• Do not alter or modify this restraint.
• Repairs must only be done by the manufacturer or agent.
• Do not allow the restraint to come into contact with polishes, oils,
bleach and other chemicals.
• Destroy the restraint if it has been in a severe crash, even if no
damage is visible.
• Straps may be damaged by unsecured cargo in a collision.
Secure or remove hazardous cargo before using this restraint. Hatch-back or Wagon: Do not use the child restraint where this strap may fall into a split in the seat back.
Always attach hook and remove slack.
• FAILURE TO PROPERLY USE THIS SAFETY SEAT INCREASES THE RISK OF SERIOUS INJURY OR DEATH IN A SHARP TURN, SUDDEN STOP OR CRASH.
• THIS RESTRAINT MUST BE USED IN CAR WITH FORWARD FACING SEATS WITH A LAP-SASH SEATBELT.
• THIS RESTRAINT IS NOT SUITABLE FOR USE WHERE THE ANCHORAGE STRAP MAY FALL INTO A SPLIT IN THE SEAT BACK (E.G. HATCHBACK OR WAGON).
• DO NOT USE THIS RESTRAINT WITHOUT THE COVER.
Contact IGC Dorel (Australia) for genuine replacement part on 1300 809 526
• Seat belt extenders should not be used if the seatbelt is not
long enough to secure the child restraint.
• TO BE USED WITH A LAP-SASH/LAP-ONLY SEATBELT IN THE FRONT/BACK OF MOST CARS WITH FORWARD FACING SEATS
4
WarnInG
WHEN USED AS A CHILD RESTRAINT
(6 months to 4 years approximately)
• Fit the restraint firmly to the car seat.
• Fit the harness firmly to the child.
• A loose restraint or harness is dangerous.
• Ensure the belt webbing is not twisted.
WHEN USED AS A BOOSTER SEAT
(4 years TO approximately 6 TO 8 YEARS)
• DO NOT USE WITH JUST A LAP BELT. You must use with a lap-sash belt or with a seat belt.
• The lap part of the seatbelt must be firmly across the thighs and
the sash straps fitted diagonally across the chest and on the shoulder.
• THIS BOOSTER SEAT IS NOT SUITABLE FOR USE WITH A
CHILD HARNESS.
WarnInG
• DO NOT LEAVE CHILDREN UNATTENDED IN THE CAR.
5
WarnInG
to parents and other users
• DO NOT MODIFY YOUR CONVERTIBLE BOOSTER SEAT or use any accessories or parts supplied by other manufacturer’s.
• NEVER USE CONVERTIBLE BOOSTER SEAT IF IT HAS
DAMAGED OR MISSING PARTS.
• DO NOT use a cut, frayed or damaged vehicle seat belt.
• THE CONVERTIBLE BOOSTER SEAT CAN BECOME VERY
HOT IF LEFT IN THE SUN.
• Always lightly touch the surface of any metal or plastic parts to
check their temperature BEFORE putting your child in the Booster Seat. Contact with these parts can burn your child’s skin.
• The restraint should not be purchased or sold as a second hand item. It is recommended not to use child restraints older than 10 years as the protection in an accident may be reduced
• ALWAYS ENSURE THAT BOOSTER SEAT HAS TETHER STRAP ATTACHED, AND THE VEHICLE’S SEAT BELTS
ARE USED TO SECURE THE BOOSTER SEAT TO THE
VEHICLE EVEN WHEN NO CHILD IS IN THE SEAT.
6
WarnInG
ANCHORAGE FITTING INSTALLATION
Read and follow all of the installation instructions for maximum
protection. If you have any questions regarding the installation or
use of this restraint, please contact IGC Dorel or agent, or a child
restraint fitting station authorised by the relevant transport authority,
or in New Zealand, to consult the agent for the vehicle.
Do not modify or alter this restraint in any way. Use only IGC
Dorel recommended parts and accessories.
Protect all webbing from possible damage by sharp edges and
corners.
Check your vehicle owner’s handbook for the location of correct anchorage points and possible need for spacers. If a suitable anchorage point cannot be found, contact a child restraint fitting station for
recommendations about your vehicle.
Some vehicles may have anchor points which are recessed below
the vehicle trim, spacers are supplied to raise the anchor point if
required.
An extension strap may be needed for vehicles without a fixed
parcel shelf. Extension straps and extra fittings are available from
various stores.
Note : Extension straps 300mm ref no. 921, 600mm ref no. 922
and an anchor bolt kit, ref no.525
Seat belt extenders should not be used if the seat belt is not long
enough to secure the child.
7
IMPORTANT
Child restraints must be used correctly to provide proper protection
for your child. The new type of clip anchorage system on child
restraint must be used in the correct way.
Be especially careful to use the clip in the following way.
RIGHT
Make sure there is no slack in the top strap and the attachment clip
is upright in the anchorage fitting.
WRONG
The clip must not lie flat on the anchorage fitting.
FLOOR MOUNTED ANCHORAGES
ANCHORAGES IN VERTICAL PANEL AT REAR OF VEHICLE
8
ANCHORAGE FITTING INSTALLATION (continue)
If the car is fitted with a child restraint anchorage point. Locate the
anchorage points behind the rear seating position (consult the car
owner’s handbook for the location of the anchorage point). Remove
the thread plug from the parcel shelf / floor/ roof and install the attachment bolt as shown in Fig 1.
Attachment Bolt
Lock Washer
Anchor Fitting
Spacers (if required)
Vehicle Trim
WarnInG
CAUTION: DO NOT OVERTIGHTEN
THE ATTACHMENT BOLT. MAXIMUM
TORQUE 20 Newton Metre.
Front of vehicle
Fig 1
Vehicle Metal Structure
If the car is not fitted with a child restraint anchorage point.
For sedans only – Drill a 9mm diameter hole in the parcel
shelf on the centre – line of the seating position as shown in Fig 2
(page 10). Install the anchor bolt as shown in Fig 3 (page 10).
For vehicles other than sedans – In Australia, consult your nearest
child restraint fitting station or traffic authority for vehicle inspection
to find the best, correct position for the placement of anchorage
point, and for the correct attachment bolt length and use of spacers.
In New Zealand, consult the agent for the vehicle.
WarnInG
CHILD RESTRAINTS MUST NOT BE ATTACHED TO UNSOUND
METAL OR TO WOOD OR SYNTHETIC
STRUCTURES. WHEN DRILLING THE 9MM HOLE DO NOT
DRILL THROUGH FUEL LINES, FUEL TANKS, ELECTRICAL
WIRING, OR RADIO SPEAKERS. WEBBING STRAPS MUST BE
PROTECTED FROM SHARP CORNERS AND EDGES.
THE ANCHOR FITTINGS MUST BE USED ONLY AS DESCRIBED
ABOVE. IT MUST NOT BE HOOKED ONTO ANY OTHER OBJECT.
9
Centre-line of seating position
Attachment bolt
Spacers (if required)
Vehicle Trim
Reinforcing Washer
Fig 3
Front of vehicle
Fig 2
Anchor Fitting
Vehicle Metal
Structure
Lock Washer
Securing Nut
Front of vehicle
WarnInG
VEHICLE SEAT LOCATION
IMPROPER PLACEMENT OF THE SAFETY SEAT
INCREASES THE RISK OF SERIOUS INJURY OR DEATH.
Some seating positions in your vehicle may NOT be safe for this
safety seat. Some vehicles do not have any seating positions that
can be used safely with the seat. If you are not sure where to place
the Booster Seat in your vehicle, consult your vehicle’s owner’s
handbook.
10
CORRECT VEHICLE POSITION
corrEct usE
corrEct usE
IncorrEct usE
11
TETHER STRAP AND HEADREST
ADJUSTMENT
GENERAL INSTRUCTIONS
Button
12
TOP ANCHORAGE STRAP
To attach the anchorage
strap, Place one knee in the
child seat and push down
firmly then attach hook to
anchor in vehicle.
Adjust anchorage strap and
remove slack. Pull loose end of
strap to tighten.
Press on the adjuster button
with thumb and pull strap back
through to loosen anchorage
strap using strap which is
attached to the seat.
anchor hook
Vehicle
anchor kit
ADJUSTING THE HEADREST
HEIGHT
The Seat is fitted with headrest
Height Adjustment Lock which
is RED in colour.
Pushing it in unlocks the
headrest to move it up or down
into the desired height position.
5 Height positions are available.
RECLINING BACKREST
TO RECLINE BACKREST
Push the backrest of the seat
to recline it backward for
greater comfort if needed.
GENERAL INSTRUCTIONS
FOR UPRIGHT POSITION
Pull the backrest of the
seat forward in the upright
position .
13
FEATURES - tODDLER RESTRAINT WITH
6 POINT HARNESS
Toddler restraint with built in harness
fRONT VIEW
1
7
*opening slit in trim
8
2
3
9
4
10
5
6
1. Headrest/Trim
6. Harness Adjuster Strap
2. Forward Facing Belt 7. Air Protect (If fitted)
Path Indicators (yellow)
3. Belt Mates (If fitted)
9. Armrest/Cover (If fitted)
4. Quick Release Buckle
10. Insert (If fitted)
5. Centre Front Adjuster
Lever
14
8. Harness Slot
To be used from 6 months to approximately 1 year)
FEATURES - tODDLER RESTRAINT WITH
6 POINT HARNESS
BACK VIEW
12
16
17
13
18
14
Trim style and design may vary.
11. Adjustable Headrest Button (5 positions)
12. Tether Strap
16. Adjuster (Tether Strap)
Toddler restraint with built in harness
11
15
17. Pocket (Instruction manual)
18. Adjuster (Tether Strap)
13. Hook
14. Splitter Plate
15. Booster SeatBelt Path Indicators (red)
15
Toddler restraint with built in harness
tODDLEr shoulder height marker
LABEL 3
LABEL 2
LABEL 1
sHoulDErs Must BE
LABEL 1
aBoVE tHIs lInE
cHanGE to BoostEr MoDE WHEn
LABEL 2
sHoulDErs rEacH tHIs lInE
To be used in forward-facing position by children whose
shoulders are above the lower shoulder height marker
LABEL 1 (approximately 6 months of age) until their
shoulders reach the middle shoulder height marker LABEL 2
(approximately 4 years of age). Then convert the child
restraint to booster mode and use a lap sash belt only.
See page 22 to 26.
16
tODDLER RESTRAINT INSTALLATION
USING LAP-SASH ONLY
The shoulder straps must be
in the slots which are nearest
to the child’s shoulders, but
not more than 25 mm below
the child’s shoulders.
NOTE:
If the baby’s neck muscles are unable to support their head,
then the child should remain in a rear facing seat.
Toddler restraint with built in harness
To be used with a lap sash
belt only.
17
PREPARING SEAT TO FIT YOUR CHILD
Toddler restraint with built in harness
You MUST make these adjustments with your child
before you install the child restraint in the vehicle. Please
adjust harness according to the infants shoulder height
prior to installation.
18
TO ADJUST SHOULDER
STRAP HEIGHT:
1. Press the harness release lever at the front of seat.
2. Pull both shoulder straps simultaneously to lossen.
2
•
4
1
5
SPLITTER PLATE
3
3. Undo the straps from the
splitter plate on the back of the
child restraint. Re-thread the
shoulder straps through the
desired slots. Reconnect the
straps to the splitter plate.
4. Press red button to release buckle assembly for ease of child fitment. Place child in seat.
To tighten:
5. Fasten buckle assembly
(See Page 19). Pull the adjuster
belt at the front of the seat until
the harness belt lies firmly
against the child.
PREPARING SEAT TO FIT YOUR CHILD
stEP 2
stEP 3
Step 1 : Insert one buckle tongue as shown above.
Step 2 : Insert the second buckle tongue as illustrated
above. Listen for a ‘CLICK’.
Step 3 : Remember to always pull up on the harness straps
to make sure buckle is locked properly.
WarnInG
DO NOT USE SHOULDER STRAPS OF UNEQUAL HEIGHTS.
CORRECT USE
Toddler restraint with built in harness
stEP 1
INCORRECT USE
Ensure the harness is attached to the splitter plate. Ensure
the harness is pulled through the plastic mould & trim all the
way and correctly tensioned. Ensure harness straps and
adjuster strap is not twisted.
19
Toddler restraint with built in harness
tODDLEr USE INSTALLATION
1
2
4
3
FORWARD FACING SEAT INSTALLATION:
1. Thread the vehicle lap-sash belt through the yellow belt
path indicators.
2. Position the lap part around the armrest as illustrated.
3. Thread the lap-sash belt between the seat back and trim.
Thread the lap sash belt through the opening. Refer to
illustration.
4. Position the lap sash belt around the armrest and lock
the car buckle. Listen for ‘CLICK’ and gently pull to ensure
buckle is locked.
NOTE: Ensure that the tether strap is attached at all times.
Refer to page 12 for fitment.
Place one knee on the child restraint and push down firmly while
pulling up on belt to tighten. Ensure all slack is taken out.
With weakest hand, tilt and push the child restraint forward
and back, and from side to side. If the seat belt does not
loosen, your child seat should be secure. If not : Change
seat position.
20
CHILD shoulder height marker
LABEL
LABEL
LABEL
LABEL 2
sHoulDErs rEacH tHIs lInE
sHoulDErs Must BE
LABEL 3
CHILD USE AS A BOOSTER SEAT
cHanGE to BoostEr MoDE WHEn
BEloW tHIs lInE
To be used as a booster mode when the child shoulders
are above the middle height marker LABEL 2 until their
shoulders reach the upper height marker LABEL 3
(approximately 6 to 8 years). Then the child needs to be
moved into the next form of restraint when they reach the top
shoulder height marker. See page 27
21
FEATURES - CHILD BOOSTER SEAT
fRONT VIEW
1
CHILD USE AS A BOOSTER SEAT
5
*opening slit in trim
2
6
3
4
7
1. Headrest/Trim
6. Seat Trim
2. Car Lap-Sash Belt
7. Booster SeatBelt Path 3. Storage for buckle
4. Storage for Harness
Adjuster Strap
5. Air Protect (if fitted)
22
Indicators (red)
FEATURES - CHILD BOOSTER SEAT
BACK VIEW
9
13
14
10
11
15
*Thread the
straps for
storage
CHILD USE AS A BOOSTER SEAT
8
12
Trim style and design may vary.
8. Adjustable Headrest Button (5 position)
9. Tether Strap
10. Hook
13. Adjuster (Tether Strap)
14. Pocket (Storage for
Instruction manual)
15. Anchorage Fitting
11. Shoulder Straps Storage
12. Booster SeatBelt Path
Indicators (red)
23
REMOVE HARNESS SYSTEM
CHILD USE AS A BOOSTER SEAT
SPLITTER PLATE
Undo the straps from the splitter
plate on the back of the child
restraint. Pull harness adjuster
strap forward to the maximum.
See feature (6) on page 14.
Roll the harness adjuster strap
and store in the opening area
under trim. See feature (4) on
page 22.
Press red button to release
buckle assembly. Insert buckle
in the opening area on the seat
covered under the flap.
See feature (3) on page 22.
Remove both shoulder straps from the harness slots ,
See feature (8) on page 14. Thread the shoulder straps
through the opening between the armrest and side of the
seat, refer to illustration on page 23. Store the straps and
(belt mates if fitted) in the opening area at the back on the
seat, refer to feature (11) on page 23.
24
BOOSTER SEAT INSTALLATION USING
LAP-SASH ONLY
Securing Your Child In Vehicle
Position the sash belt through the shoulder belt guide in the
headrest. The lap belt portion MUST be positioned low on the
hips, Fasten buckle and pull up on shoulder belt to tighten.
The vehicle’s seat belts MUST NOT be twisted.
CORRECT
INCORRECT
CHILD USE AS A BOOSTER SEAT
Place the Booster Seat firmly against the back of a forward
facing vehicle seat equipped with lap-sash belt.
DO NOT place the Booster Seat in a vehicle without the
tether strap attached to the vehicle’s anchor fitting. Refer
to page 12.
Have your child sit in the safety seat with their back flat
against its back.
INCORRECT
WarnInG
A sash belt under the arm or
behind the back is dangerous
25
BOOSTER SEAT INSTALLATION USING
LAP-SASH ONLY
CHILD USE AS A BOOSTER SEAT
Correct Shoulder Position
26
To ensure the correct head
support is obtained, the
bottom of the headrest MUST
be even or slightly higher with
the top of child’s shoulders as
illustrated.
NOTE : If the vehicle seat belt lays across child’s neck or
face, then readjust the headrest height.
CAUTION!
In the event of a crash, a seat belt across the child’s throat
could cause a strangulation hazard.
THE NEXT SEAT FOR YOUR CHILD
LABEL 3
HEADREST AT HIGHEST POSITION
sHoulDErs Must BE
BEloW tHIs lInE
GENERAL INSTRUCTIONS
The booster seat is unsuitable for the occupant when the
shoulders are above the upper marker (LABEL 3). The child
needs to be moved into the next form of child restraint
(a bigger booster seat or a child harness) when they reach
the top shoulder height marker.
NOTE: This illustration is
representative only.
Design and style may vary.
CHILD HARNESS
From 7 to 10 years of age
BOOSTER SEAT
Approx 4 to 10 years
of age
27
CARE AND MAINTENANCE
NOTE: Remove harness as described on page 24.
GENERAL INSTRUCTIONS
Headrest cover: Adjust the booster seat headrest to its
highest position. Separate velcro at the back of the headrest
and remove cover.
Main body cover: Separate velcro at the back of the seat.
Pull off the elastics around the armrest and remove cover off
the seat.
• The seat covers can be machine washed in lukewarm
water on the ‘Delicate’ cycle.
• Tumble dry for 10 - 15 minutes on low heat.
• DO NOT BLEACH
• DO NOT DRY CLEAN
• DO NOT IRON
Style and design may vary
for the trim.
Elastic Strap
28
CARE AND MAINTENANCE
VELCRO
The insert is to be used from 6
months to approximately 1 year)
To replace insert (If fitted)
Feed the crotch part of the
buckle through the opening
slot in the insert. Place the
shoulder straps as illustrated
and attach velcro 2 places.
Fasten buckle assembly.
GENERAL INSTRUCTIONS
To Remove insert (If fitted)
To remove the insert,
separate the velcro 2 places.
Refer to illustration above.
Undo the buckle and pull the
insert out.
Fitting the headrest cover
Extend the booster seat headrest to its highest position then
fit the headrest cover (pull on cover) by stretching it over the
headrest.
Fitting the main body cover
Starting at the shoulders, place the trim on and fasten the
velcro at the back . Next, on each side of the trim you will
see elastics, these elastics need to be threaded around the
armrest and attached. Last step, pull cover over base.
29
GENERAL INSTRUCTIONS
VERY IMPORTANT:
Only use this child restraint
with the cover supplied or a
manufacturer-authorized
replacement cover with identical
shoulder height markers.
CARE AND MAINTENANCE
• CLEANING METAL AND PLASTIC PARTS - Sponge
clean with mild soap and cool water. NEVER clean
with ammonia or bleach based, or spirit-type cleaners.
• DO NOT USE THIS SAFETY SEAT WITHOUT ITS
COVER
• FROM TIME TO TIME CHECK THE SEAT for worn
parts, torn material and stitching. If damage is found,
DO NOT try to modify the safety seat. Replace the
safety seat.
• IMPORTANT - Only genuine replacement parts
supplied by IGC Dorel Pty Ltd can be used on the
Convertible Booster Seat.
30
Follow the manufacturer’s instructions at all times. Before
removal, ensure you have carefully noted the way which the
various parts are attached to the seat so as to facilitate
reassembly.
Your child car seat is equipped with a buckle designed to
give your child maximum protection during proper use.
When working properly, your buckle should always fasten with
an audible “click”.
If sticky liquids such as baby food, fruit juice, etc, get into the
buckle it may become sluggish and you will not hear a “click”.
The buckle should be cleaned by following the steps below.
GENERAL INSTRUCTIONS
Place the buckle unit under running water (40 degrees Celsius)
Let the water flow through the mouth of the buckle for one
minute. Simultaneously latch and unlatch the tongues into the
buckle several times until a strong audible “click” is heard.
If you still cannot hear a strong audible “click” after latching
the buckle several times, then repeat the process again.
DO NOT oil any part of the buckle and allow buckle to dry.
IMPORTANT - Only genuine replacement parts supplied by
IGC Dorel Pty Ltd can be used on the Convertible Booster
Seat.
31
WARRANTY
IGC DOREL PTY LTD WARRANTS YOUR NEW PRODUCT TO BE FREE
FROM DEFECTS IN MATERIALS AND WORKMANSHIP FOR 6 YEARS ON
THE SEAT & 2 YEARS ON THE TRIM, FROM THE DATE OF PURCHASE,
PROVIDED THAT THE PRODUCT IS USED IN ACCORDANCE WITH
ACCOMPANYING RECOMMENDATIONS OR INSTRUCTIONS WHERE
PROVIDED. THE BENEFIT OF THIS WARRANTY IS IN ADDITION TO
YOUR RIGHTS UNDER THE AUSTRALIAN CONSUMER LAW AND TO
OTHER RIGHTS AND RE MEDIES OF THE CONSUMER UNDER A LAW IN
RELATION TO THE GOODS OR SERVICES TO WHICH THE WARRANTY
RELATES.
IGC DOREL PTY LTD WILL PROVIDE YOU WITH YOUR CHOICE OF A
REFUND, REPAIR OR EXCHANGE (WHERE POSSIBLE) FOR THIS PRODUCT
IF IT BECOMES DEFECTIVE WITHIN THE WARRANTY PERIOD. IGC
DOREL PTY LTD WILL BEAR THE REASONABLE EXPENSE OF CLAIMING
THE WARRANTY. THIS WARRANTY WILL NO LONGER APPLY WHERE THE
DEFECT IS A RESULT OF ALTERATION, ACCIDENT, MISUSE, ABUSE OR NEGLECT.
PLEASE RETAIN YOUR RECEIPT AS PROOF OF PURCHASE AND
CONTACT OUR CUSTOMER SERVICE CENTRE ON PH: 1300 809 526 OR
ALTERNATIVELY, VIA OUR WEBSITE AT WWW.IGCDOREL.COM.AU FOR
ANY DIFFICULTIES WITH YOUR PRODUCT. WARRANTY CLAIMS AND
CLAIMS FOR EXPENSE INCURRED IN RETURNING THIS PRODUCT CAN
BE ADDRESSED TO OUR CUSTOMER SERVICE CENTRE AT 655-685
SOMERVILLE ROAD, WEST SUNSHINE VIC 3020.
FOR NEW ZEALAND PLEASE CONTACT CUSTOMER SERVICE CENTRE,
14 SIR WILLIAM AVENUE, EAST TAMAKI, AUCKLAND, 2013. AUCKLAND:
(09) 274 1040 NZ WIDE: 0800 628 000 (TOLL FREE). HOURS: 8:00 AM 4:00 PM, MONDAY TO FRIDAY.
OUR GOODS COME WITH GUARANTEES THAT CANNOT BE
EXCLUDED UNDER THE AUSTRALIAN CONSUMER LAW.
YOU ARE ENTITLED TO A REPLACEMENT OR REFUND FOR A
MAJOR FAILURE AND COMPENSATION FOR ANY OTHER
REASONABLY FORESEEABLE LOSS OR DAMAGE. YOU ARE
ALSO ENTITLED TO HAVE THE GOODS REPAIRED OR
REPLACED IF THE GOODS FAIL TO BE OF ACCEPTABLE
Australian
QUALITY AND THE FAILURE DOES NOT AMOUNT TO A
Standard
MAJOR FAILURE.
AS/NZS 1754 Lic 1491
SAI Global
IMPORTANT: KEEP THIS BOOKLET IN THE POCKET
PROVIDED AT THE REAR OF THE CHILD RESTRAINT
ref # 012210 a
11/12