JDSU | Selection Guide | Tips and Adapters | 2013 Edition

Tips and Adapters | 2013 Edition
Fiber Inspection
SELECTION GUIDE
30175769
REV 0
Tips and Adapters for Fiber Inspection
Table of Contents
JDSU Tips and Adapters for Fiber Inspection.................................................................................................2–4
Standard Patch Cord Tips............................................................................................................................................................2
Standard Bulkhead Tips................................................................................................................................................................2
Long-Reach Bulkhead Tips.........................................................................................................................................................2
RibbonDrive™ Tips ...........................................................................................................................................................................3
Angled Tips (60 degrees).............................................................................................................................................................3
Universal Flare and FMA Adapters........................................................................................................................................3
FMAE Adapters....................................................................................................................................................................................3
Installing FBPT Tips on FBP-Series Probes.......................................................................................................................4
Barrel Assemblies......................................................................................................................................................................... 4
Universal Tips and Adapters............................................................................................................................................... 5
LC Tips and Adapters................................................................................................................................................................. 6
SC Tips and Adapters................................................................................................................................................................. 7
FC Tips and Adapters................................................................................................................................................................. 8
ST Tips and Adapters................................................................................................................................................................. 9
SMA Tips and Adapters............................................................................................................................................................ 9
E2000 Tips and Adapters.....................................................................................................................................................10
MU Tips and Adapters............................................................................................................................................................10
ODC Guides.....................................................................................................................................................................................11
Ribbon (MTP) Tips and Adapters..................................................................................................................................12
Ribbon (MTP APC) Tips and Adapters......................................................................................................................12
Ribbon (MPX) Tips and Adapters..................................................................................................................................13
Ribbon (Other) Tips and Guides....................................................................................................................................13
OptiTap Tips....................................................................................................................................................................................14
OptiTip Tips.....................................................................................................................................................................................14
1
JDSU Fiber Inspection
JDSU Tips and Adapters for Fiber Inspection
Standard Patch Cord Tips
These tips are for looking at patch cords
(e.g., pigtails, male connectors, etc.). Currently
available are two main “Universal Patch Cord”
tips. One tip is compatible with 2.5mm ferrules
(e.g., FC, SC, ST) while the other works well for
1.25mm ferrules (e.g., LC, MU). There are also
dedicated tips for looking at APC patch cords.
FBPT-U25M
(2.5mm)
FBPT-U12MA-SF
(1.25mm - APC)
FBPT-U12M
(1.25mm)
Standard Bulkhead Tips
These are specific tips for viewing common
connectors through a bulkhead adapter. These
tips allow you to inspect the fiber surface
located behind of the bulkhead (e.g., inside
hardware devices or on the back side of patch
panels).
FBPT-SC
FBPT-FC-P
FBPT-SC-APC
Align & insert the key on the tip into the
key channel of the bulkhead adapter.
To attach/secure to barrel
assembly, align & insert the key
on the tip into the key channel of
the barrel assembly and thread.
Long-Reach Bulkhead Tips
Small form-factor connectors can produce
some tight work spaces. In cases where you
may want to inspect a single channel while
the adjacent channels are still occupied with
connectors or dust plugs. You may need to
use a narrow tip with a little longer reach. For
this situation we recommend using our Long
Reach tips, usually denoted as “-L.” They have
about 1/2” longer reach than our standard tips
and do not have the forward retaining nut.
They can therefore “reach” between connectors
and inspect ports quickly and easily. This also
reduces the chances of contaminating adjacent
channels during inspection.
SELECTION GUIDE: JDSU Tips and Adapters – 2013 Edition
FBPT-LC-L
FBPT-SC-L
2
Tips and Adapters for Fiber Inspection
RibbonDrive™ Tips
JDSU has developed several configurations of patented
RibbonDrive™ probe tips for inspection of high-density,
multifiber array connectors end faces. These dedicated tips
are designed to inspect connectors that are mounted within a
bulkhead adapter (in-situ inspection). Each tip mates securely
with bulkhead mating adapters using a precision-keyed
interface. The “panning” and “scrolling” knobs allow the user to
view each fiber individually across both the X & Y axes of the
fiber arrays.
FBPT-LC-A6
FBPT-MTPA-L
Angled Tips (60 Degrees)
Our angled tips, denoted as “-A6,” are angled at 60 degrees to
allow inspection of transceivers and other hard-to-reach fibers.
Regardless of where the transceiver is mounted on a PCB, the
probe and tip can be maneuvered to fit into the transceiver and
provide high-quality microscopic inspection.
FBPT-SC-A6
Universal Flare and FMA Adapters
If you are familiar with JDSU’s benchtop fiber inspection
products, you probably have seen our complete line of quality,
high-performance adapters (FMA’s). If you would like to use
your “FMA” adapters (ex: FMA-MTPA, FMA-E2A, etc.), with a
probe microscope, the universal flare adapter (FBPT-UFMA)
make this possible.
FMA-U12
(FMA Adapter)
FMA-MTPA
(FMA Adapter)
FMAE Adapters
FMAE adapters are used in conjunction with the integrated
Patch Cord Microscopes (PCM) that are on many of our
handheld devices (ex: OLP-82P). Having dedicated microscopes
for inspecting both ends (PCM for Patch Cord & Probe for
Bulkhead) of a connection improves workflow and efficiency by
eliminating the need to change tips to inspect both sides.
3
FMAE-U25
FMAE-MTP
FBPT-UFMA
(Universal Flare Adapter)
JDSU Fiber Inspection
Installing FBPT Tips on FBP-Series Probes
Some tips require an optical barrel assembly (which is included with the probe), while other tips already include their own optics and can
attach directly to the probe without the need of a barrel assembly.
with Barrel Assembly
BARREL ASSEMBLY
(FBPP-BAP1)
Notch-key and
Key Channel
without Barrel Assembly
INSPECTION TIP
(FBPT-U25M)
Objective Lens
Front and Back
Retaining Nut
INSPECTION TIP
(FBPT-LC-L)
Notch-key
and Key
Channel
Retaining Nut
Barrel Assemblies
Image
Description
Part Number
Standard Barrel Assembly for probe
NOTE: This is included with every probe.
FBPP-BAP1
Extended length Barrel Assembly for probe; compatible with all of the same
tips as the FBPP-BAP1, but provides an additional 3cm of reach
FBPP-BAP2
Narrow Barrel Assembly for probe; used in conjunction with specific tips (ex:
FBPT-U12M-N) that require a narrower diameter
FBPP-BAP3
NOTE: JDSU has over 300 tips and adapters available for inspecting different fiber optic connectors for a variety of different applications. This
Selection Guide is not an all-inclusive list, but provides solutions for the most common connectors and applications.
SELECTION GUIDE: JDSU Tips and Adapters – 2013 Edition
4
Tips and Adapters for Fiber Inspection
Universal Tips and Adapters
Image
5
Connector Type
Application
Description
Part Number
SC, FC, ST,
E2000
Patch Cord
TIP: Universal 2.5mm patch cord for FBP
FBPT-U25M
(APC) SC, FC,
ST, E2000
Patch Cord
TIP: Universal 2.5mm patch cord APC polish for FBP
FBPT-U25MA
SC, FC, ST,
E2000
Patch Cord
ADAPTER: Universal 2.5mm female threaded
(for Patch Cord Microscopes)
FMAE-U25
(APC) SC, FC,
ST, E2000
Patch Cord
ADAPTER: Universal 2.5mm APC female threaded
(for Patch Cord Microscopes)
FMAE-UAPC
LC, MU
Patch Cord
TIP: Universal 1.25mm patch cord for FBP
FBPT-U12M
(APC) LC,
MU
Patch Cord
TIP: Universal 1.25mm patch cord APC polish slip
fit for FBP
FBPT-U12MA-SF
LC, MU
Patch Cord
ADAPTER: Universal 1.25mm female threaded
(for Patch Cord Microscopes)
FMAE-U12
38999/
ARINC
Military &
Aerospace
TIP: Universal 1.25mm mil termini for FBP
(requires FBPP-BAP3 barrel assembly)
FBP-U12M-N
JDSU Fiber Inspection
LC Tips and Adapters
Image
Connector Type
Application
Description
Part Number
LC
Bulkhead
TIP: LC bulkhead for FBP
FBPT-LC
LC
Bulkhead
TIP: LC bulkhead long-reach for FBP
FBPT-LC-L
NOTE: Highly recommended for inspecting high density
LC bulkhead applications.
LC
Bulkhead
TIP: LC bulkhead for FBP square angled 60 degrees
FBPT-LC-A6S
LC
Patch Cord
ADAPTER: LC female threaded
(for Patch Cord Microscopes)
FMAE-LC
LC
Patch Cord
ADAPTER: LC duplex female threaded
(for Patch Cord Microscopes)
FMAE-LC-2X
NOTE: Highly recommended for inspecting duplex LC
patch cords.
LC-APC
Bulkhead
TIP: LC-APC bulkhead for FBP
FBPT-LC-APC
LC-APC
Bulkhead
TIP: LC-APC bulkhead for FBP angled
60 degrees
FBPT-LCA-A6
LC-APC
Patch Cord
ADAPTER: LC-APC female threaded
(for Patch Cord Microscopes)
FMAE-LCA
GUIDEBOOK: JDSU Tips and Adapters – 2013 Edition
6
Tips and Adapters for Fiber Inspection
SC Tips and Adapters
Image
Connector Type
Application
Description
Part Number
SC
Bulkhead
TIP: SC bulkhead for FBP
FBPT-SC
SC
Bulkhead
TIP: SC bulkhead long-reach for FBP
FBPT-SC-L
SC
Bulkhead
TIP: SC bulkhead for FBP angled 60 degrees
FBPT-SC-A6
SC, FC
Bulkhead
TIP: Both SC and FC bulkhead for FBP angled 60
degrees
FBPT-SCFC-A6
SC
Patch Cord
ADAPTER: SC duplex female threaded
(for Patch Cord Microscopes)
FMAE-SC-DUX
NOTE: Highly recommended for inspecting duplex SC
patch cords.
7
SC-APC
Bulkhead
TIP: SC-APC bulkhead for FBP
FBPT-SC-APC
SC-APC
Bulkhead
TIP: SC-APC bulkhead for FBP angled 60 degrees
FBPT-SCA-A6
SC-APC
Patch Cord
ADAPTER: SC-APC female threaded
(for Patch Cord Microscopes)
FMAE-SCA
SC2
Bulkhead
TIP: SC2 bulkhead for FBP
FBPT-SC2
SC2
Bulkhead
TIP: SC2 bulkhead long reach for FBP
FBPT-SC2-L
SC2
Bulkhead
TIP: SC2 bulkhead extra long for FBP
FBPT-SC2-XL
JDSU Fiber Inspection
FC Tips and Adapters
Image
Connector Type
Application
Description
Part Number
FC
Bulkhead
TIP: FC bulkhead for FBP
FBPT-FC
NOTE: This tip provides a push fit engagement with the
FC bulkhead.
FC
Bulkhead
TIP: FC bulkhead pro version for FBP
FBPT-FC-P
NOTE: This tip threads directly onto the FC bulkhead to
provide a secure connection for inspecting.
FC
Bulkhead
TIP: FC bulkhead for FBP angled 60 degrees
FBPT-FC-A6
FC
Bulkhead
TIP: FC bulkhead pro version for FBP angled 60
degrees
FBPT-FC-A6P
FC, SC
Bulkhead
TIP: Both FC and SC bulkhead for FBP angled
60 degrees
FBPT-SCFC-A6
FC-APC
Bulkhead
TIP: FC-APC bulkhead for FBP
FBPT-FC-APC
FC-APC
Bulkhead
TIP: FC-APC bulkhead long reach for FBP
FBPT-FCAPC-L
FC-APC
Bulkhead
TIP: FC-APC bulkhead for FBP no front mounting
collar
FBPT-FCA-1
SELECTION GUIDE: JDSU Tips and Adapters – 2013 Edition
8
Tips and Adapters for Fiber Inspection
ST Tips and Adapters
Image
Connector Type
Application
Description
Part Number
ST
Bulkhead
TIP: ST bulkhead for FBP
FBPT-ST
ST
Bulkhead
TIP: ST bulkhead long reach for FBP
FBPT-ST-L
ST
Bulkhead
TIP: ST bulkhead for FBP angled 60 degrees
FBPT-ST-A6
Connector Type
Application
Description
Part Number
SMA
Bulkhead
TIP: SMA bulkhead for FBP
FBPT-SMA
SMA
Bulkhead
TIP: SMA bulkhead angled 60 degrees for FBP
FBPT-SMA-A6
SMA
Buikhead
TIP: SMA bulkhead pro version for FBP
FBPT-SMA-P
SMA Tips
Image
9
JDSU Fiber Inspection
E2000 Tips and Adapters
Image
Connector Type
Application
Description
Part Number
E2000
Bulkhead
TIP: E2000 bulkhead for FBP APC or PC polish
FBPT-E2000
E2000,
E2000-APC
Bulkhead
TIP: E2000 bulkhead for FBP angled 60 degrees
(compatible with both PC and APC types)
FBPT-E2A-A6
E2000-APC
Patch Cord
ADAPTER: E2000 female threaded
FMAE-E2A
NOTE: This adapter works for both PC and APC E2000
connectors.
MU Tips
Image
Connector Type
Application
Description
Part Number
MU
Bulkhead
TIP: MU bulkhead for FBP
FBPT-MU
MU
Bulkhead
TIP: MU bulkhead long reach for FBP
FBPT-MU-L
MU
Bulkhead
TIP: MU bulkhead extra long reach for FBP
FBPT-MU-XL
SELECTION GUIDE: JDSU Tips and Adapters – 2013 Edition
10
Tips and Adapters for Fiber Inspection
ODC Guides
Image
Connector Type
Application
Description
Part Number
ODC
FTTA
TIP KIT: Inspection package for ODC 2-Contact
connector
FBPT-ODC-2
Contents include:
• Barrel Assembly, Narrow (FBPP-BAP3)
• Guide, ODC Plug, Sockets, with 2 contacts,
1.25mm (FBPT-ODC-G001)
• Guide, ODC Receptacle, Pins, with 2 contacts,
1.25mm (FBPT-ODC-G002)
ODC
FTTA
TIP KIT: Inspection package for ODC 4-Contact
connector
FBPT-ODC-4
Contents include:
• Barrel Assembly, Narrow (FBPP-BAP3)
• Guide, ODC Plug, Sockets, with 4 contacts,
1.25mm (FBPT-ODC-G003)
• Guide, ODC Receptacle, Pins, with 4 contacts,
1.25mm (FBPT-ODC-G004)
11
ODC
FTTA
TIP: Guide, ODC plug, sockets, w/ 2 contacts,
1.25mm
FBPT-ODC-G001
ODC
FTTA
TIP: Guide, ODC receptacle, pins, w/ 2 contacts,
1.25mm
FBPT-ODC-G002
ODC
FTTA
TIP: Guide, ODC plug, sockets, w/ 4 contacts,
1.25mm
FBPT-ODC-G003
ODC
FTTA
TIP: Guide, ODC receptacle, pins, w/ 4 contacts,
1.25mm
FBPT-ODC-G004
JDSU Fiber Inspection
Ribbon Tips and Adapters
Image
Connector Type
Application
Description
Part Number
Ribbon
(MTP®)
Bulkhead
TIP: MTP bulkhead long reach, x and y-axis pan
knob for FBP
(includes both X and Y axis panning)
FBPT-MTP-L
Ribbon
(MTP®)
Bulkhead
TIP: MTP bulkhead x-axis pan knob for FBP
FBPT-MTP
Ribbon
(MTP®)
Bulkhead
TIP: MTP bulkhead x-axis pan knob for FBP angled
60 degrees
FBPT-MTP-A6
Ribbon
(MTP®)
Patch Cord
ADAPTER: MTP
(for Patch Cord Microscopes)
(includes both X and Y axis panning)
FMAE-MTP
Ribbon
(MTP® APC)
Bulkhead
TIP: MTP-APC bulkhead long reach for FBP
(includes both X and Y axis panning)
FBPT-MTPA-L
Ribbon
(MTP® APC)
Bulkhead
TIP: MTP-APC bulkhead x-axis pan knob for FBP
FBPT-MTPA
Ribbon
(MTP® APC)
Patch Cord
ADAPTER: MTP angled
(for Patch Cord Microscopes)
(includes both X and Y axis panning)
FMAE-MTPA
SELECTION GUIDE: JDSU Tips and Adapters – 2013 Edition
12
Tips and Adapters for Fiber Inspection
Ribbon Tips and Adapters
Image
13
Connector Type
Application
Description
Part Number
Ribbon
(MPX)
Bulkhead
TIP: MPX bulkhead x-axis pan knob for FBP
FBPT-MPX
Ribbon
(Other)
Bulkhead
TIP: Molex AR8 for FBP
(includes both X and Y axis panning)
FBPT-AR8-24
Ribbon
(Other)
Bulkhead
GUIDE: Inspection guide Molex AR8
FBPT-AR8G
JDSU Fiber Inspection
OptiTap Tips
Image
Connector Type
Application
Description
Part Number
OptiTap
FTTH
TIP: OptiTap single fiber, optimized
FBPT-COD-L
OptiTap
FTTH
TIP: OptiTap, 60 degrees angle
FBPT-COD-A6
Connector Type
Application
Description
Part Number
OptiTip
FTTH
TIP KIT: OptiTip ribbon plug and receptacle;
includes FBPT-COD-MTOA, FBPT-MTRG, FBPT-MTPG
FBPT-COD-MT
OptiTip
(APC)
FTTH
TIP KIT: OptiTip ribbon APC plug and receptacle;
includes FBPT-COD-MTOA, FBPT-MTARG, FBPTMTAPG
FBPT-COD-MTA
OptiTip
FTTH
TIP: CON2R OptiTip ribbon optical
FBPT-COD-MTOA
OptiTap
FTTH
GUIDE: OptiTip ribbon plug
FBPT-COD-MTPG
OptiTip
FTTH
GUIDE: OptiTip ribbon receptacle
FBPT-COD-MTRG
OptiTip
(APC)
FTTH
GUIDE: OptiTip ribbon APC plug
FBPT-COD-MTAPG
OptiTip
(APC)
FTTH
GUIDE: OptiTip ribbon APC receptacle
FBPT-COD-MTARG
OptiTip Tips
Image
SELECTION GUIDE: JDSU Tips and Adapters – 2013 Edition
14
Test and Measurement Regional Sales
NORTH AMERICA
TOLL FREE: 1 866 228 3762
FAX: +1 301 353 9216
LATIN AMERICA
TEL: +1 954 688 5660
FAX: + 1 954 345 4668
ASIA PACIFIC
TEL: +852 2892 0990
FAX: +852 2892 0770
EMEA
TEL: +49 7121 86 2222
FAX: +49 7121 86 1222
www.jdsu.com/inspect
Product specifications and descriptions in this document subject to change without notice. © 2013 JDS Uniphase Corporation.
30175769
REV 0