Dalsan Gypsum Industry and Trade Inc.

ENVIRONMENTAL PRODUCT DECLARATION
as per ISO 14025 and EN 15804
Owner of the Declaration
Dalsan Gypsum Industry and Trade Inc.
Programme holder
Institut Bauen und Umwelt e.V. (IBU)
Publisher
Institut Bauen und Umwelt e.V. (IBU)
Declaration number
EPD-DGI-20130058-CBC1-EN
Issue date
18.07.2013
Valid to
17.07.2018
Gypsum based construction and industrial plasters
Dalsan Gypsum Industry and Trade Inc.
www.bau-umwelt.com / https://epd-online.com
Umwelt Produktdeklaration Name des Herstellers – Name des Produkts
General Information
Dalsan Gypsum Industry and Trade
Inc.
Gypsum based construction and
industrial plasters
Programme holder
IBU - Institut Bauen und Umwelt e.V.
Rheinufer 108
D-53639 Königswinter
Owner of the Declaration
Dalsan Gypsum Industry and Trade Inc.
1.cadde, Sincap sokak, Büyüksanayi No:12
06060 Ankara
Declaration number
EPD-DGI-20130058-CBC1-EN
Declared product / Declared unit
Gypsum based plasters / 1 kg
This Declaration is based on the Product
Category Rules:
Mineral factory-made mortar, 10-2012
(PCR tested and approved by the independent expert
committee)
Scope:
Issue date
18.07.2013
This declaration is relevant to gypsum based
construction and industrial plasters manufactured at
Dalsan Ankara Kaleboğazı facility in Turkey. The EPD
applies to all types of gypsum based plasters. It is
described as the declaration of an average product
from a manufacturer’s plant. The owner of the
declaration shall be liable for the underlying information
and evidence.
Valid to
17.07.2018
Verification
Prof. Dr.-Ing. Horst J. Bossenmayer
(President of Institut Bauen und Umwelt e.V.)
Prof. Dr.-Ing. Hans-Wolf Reinhardt
(Chairman of SVA)
The CEN Norm EN 15804 serves as the core PCR
Independent verification of the declaration and data
according to ISO 14025
internally
x externally
Dr. Olivier Muller
(Independent tester appointed by SVA)
Product
Product description
Gypsum based plasters are primarily made of stucco
(calcium sulphate hemihydrate). The other raw
materials used are calcite, expanded perlite, lime,
cellulose, retarders, starch, air-entrainers, polymer and
plasticizers.
Manufacturing starts with the stucco preparation
(grinding, calcination and separation), followed by
expanded perlite and calcite preparation for
production. After receive of the gypsum mineral
(CaSO4.2H2O) to the Dalsan’s plant, it is grinded and
heated to remove 75% of combined water, resulting in
the formation of stucco (calcium sulphate hemihydrate)
(CaSO4.½H2O). It is separated depending on the size
of powder and is then transferred to the silos for
storage. After that, dry powder is mixed with the other
raw materials. Finally, the final products are packaged
for delivery.
Dalsan manufactures various gypsum based
construction and industrial plasters to required
specifications for different applications. . Reference
standards applied are TS EN 13279-1 and TS EN
13279-2. ADERTEK, KARTEK, DERZTEK are
packaged in polypropylene laminated bags with an
average weight of 30 kg, ALEVTEK and SIVATEK with
35kg. SATENTEK is available in both Kraft bags of
15kg and polypropylene laminated bags of 30 Kg.The
main products that are part of this study are: ALÇITEK
(Projection Gypsum Plaster), SIVATEK (Manual
2
Plaster with Perlite), SATENTEK (Finishing Plaster),
KARTEK (Cornice Plaster), CERACAST (Industrial
Plaster), DERZTEK (Jointing Compound) and finally
ADERDEK (Bonding Plaster).
Application
Applications of gypsum based plasters covered under
this EPD are shown below:
ALÇITEK: It is gypsum-based, ready-to-use spray
plaster. It can be directly applied on brick, concrete,
aerated-concrete, etc.
SIVATEK: It is gypsum based specially formulated
ready-to-use bagged plaster that can be applied on
directly brick, concrete, aerated-concrete, etc.
SATENTEK: With its high adherence, this finishing
plaster is used as an undercoat for all types of
paintings. SATENTEK can be applied on SIVATEK
and ALLEV plasterboard surface.
KARTEK: It is used for the production of decorative
elements like cornices.
CERACAST: It is used in the moulds of sanitary ware
and bricks moulds in those industries.
DERZTEK: It is used at ALLEV plasterboard joints over
joint tapes.
ADERTEK: It is used for bonding ALLEV plasterboard,
EPS (expanded polystyrene), XPS (extruded
polystyrene), mineral wools (glass wool, rock wool)
and composite insulation panels over surfaces like
brick, concrete, aerated-concrete etc.
Environmental Product Declaration Dalsan Gypsum Industry and Trade Inc. – Gypsum based construction and industrial
plasters
Technical Data
Technical data for Dalsan Plasters are shown below:
Constructional data
Name
Value
Compressive strength
Adhesive shear strength
Thermal conductivity
Tensile bond strength
Flexural strength
Bulk density
Dry density
Resistance to fire
Water absorption
Unit
2 - 10
N/mm2
>0.06
N/mm2
0.39 - 0.43 W/(mK)
0.1 - 0.25 N/mm2
1 - 4.5
N/mm2
700-850
kg/m3
950-1250 kg/m3
Non
A1
combustibl
e
< 36
%
Base materials / Ancillary materials
Gypsum based mineral plasters are made of raw
materials such as stucco (calcium sulphate
hemihydrate), calcite, expanded perlite, lime, cellulose,
retarders, starch, air entraining agents, polymer and
plasticizer.
There are no products that can be included in
“Candidate List of Substances of Very High Concern
for Authorisation”. However, there are some chemicals
that are part of the EU REACH regulation and
registered: calcium sulphate (01-2119444318-260199), citric acid (05-2118519120-59-0000), calcium
di-hydroxide (05-2118519278-36-0000).
Gypsum based plasters have a long life and can be
recycled or disposed of designated landfill sites at the
end of their useful life.
Reference service life
This EPD is relevant to cradle to factory gate as well
as disposal of product after use. Therefore no
reference to useful life is required.
LCA: Calculation rules
Declared Unit
The declared unit is 1 kg gypsum based plasters in line
with the PCR document for mineral factory-made
mortar.
The process flow diagram is depicted below:
Declared unit
Name
Declared unit
Gross density
Conversion factor to 1 kg
Value
Unit
1
1063
0.00094
kg
kg/m3
-
System boundary
This is a cradle to gate EPD including disposal of
product after use. System boundary for the Life Cycle
Assessment involves raw materials (A1), transport (A2)
manufacturing (A3) and disposal (C4).
‘Raw materials stage’ includes extraction and
processing raw materials. ‘Manufacturing stage’ starts
with further processing some raw materials needed for
the production, mixing all raw materials and packaging
the final product. ‘Transport stage’ is only relevant for
delivery of all raw materials to the plant and forklift
usage within the factory.
Concerning the end of life, all gypsum based plasters
end up at landfill as their final fate. The benefit from
recycling and reuse is not relevant for this LCA work.
In addition, all waste coming from the production
processes and service areas is managed in
accordance with valid legal requirements. There is no
wastewater from the process.However, there is
wastewater arising from general use within the factory,
which is very small and treated in two biological
wastewater treatment plants. The treated water is used
in irrigation of gardens.
3
Cut-off criteria
Where there are no data available, raw materials that
are a minor constituent of the product amounting less
than 1% of total raw materials are excluded in this
study.
Comparability
Basically, a comparison or an evaluation of EPD data
is only possible if all the data sets to be compared
were created according to EN 15804 and the building
context, respectively the product-specific
characteristics of performance, are taken into account.
This EPD is comparable with gypsum based plasters
that comply with the PCR document Part B: Mineral
factory-made mortar and are evaluated according to
EN 15804 norms.
Environmental Product Declaration Dalsan Gypsum Industry and Trade Inc. – Gypsum based construction and industrial
plasters
LCA: Scenarios and additional technical information
The impact indicators were performed according to
LCA standard (ISO 14040/44) using SimaPro software
with ecoinvent (v: 2.2) database.
Reuse- Recovery-and Recycling potential (D)
All gypsum based plasters end up at construction and
demolition waste landfills. However, no possible
benefits of recycling and reuse were taken into account
in the LCA work here.
GREENGUARD Certification
Some of the products covered by this EPD have also
been awarded GREENGUARD certification. It is
awarded to products that protect human health and
quality of life by improving indoor air quality and
reducing chemical exposure when they are in use. The
GREENGUARD Environmental Institute (GEI) has
awarded GREENGUARD Indoor Air Quality
Certification® and GREENGUARD Children &
SchoolsSM Certification to the following gypsum based
mineral plasters: ALÇITEK, SIVATEK and SATENTEK.
4
Environmental Product Declaration Dalsan Gypsum Industry and Trade Inc. – Gypsum based construction and industrial
plasters
LCA: Results
The results of the LCA with the indicators as per EPD requirement are given in the following tables for product
manufacture (A1, A2, A3) and the loads beyond the system boundaries (C4).
DESCRIPTION OF THE SYSTEM BOUNDARY (X = INCLUDED IN LCA; MND = MODULE NOT DECLARED)
Replacement1)
Refurbishment1)
Operational energy
use
Operational water
use
De-construction
demolition
Transport
Waste processing
Disposal
A4
A5
B1
B2
B3
B4
B5
B6
B7
C1
C2
C3
C4
MND MND MND MND MND MND MND MND MND MND MND MND
ReuseRecoveryRecyclingpotential
Repair
X
Maintenance
A3
X
Use
Manufacturing
A2
X
END OF LIFE STAGE
Constructioninstallation process
Transport
A1
USE STAGE
BENEFITS AND
LOADS
BEYOND THE
SYSTEM
BOUNDARYS
Transport
Raw material
supply
PRODUCT STAGE
CONSTRUCTI
ON PROCESS
STAGE
D
X
MND
RESULTS OF THE LCA - ENVIRONMENTAL IMPACT: 1 kg of gypsum based mineral plasters
Parameter
Unit
Global warming potential
[kg CO2-Äq.]
Depletion potential of the stratospheric ozone layer
[kg CFC11-Äq.]
Acidification potential of land and water
[kg SO2-Äq.]
Eutrophication potential
[kg PO43-- Äq.]
Formation potential of tropospheric ozone photochemical oxidants [kg Ethen Äq.]
Abiotic depletion potential for non fossil resources
[kg Sb Äq.]
Abiotic depletion potential for fossil resources
[MJ]
A1 - A3
C4
9.772E-2
1.102E-8
2.543E-4
1.163E-4
7.249E-5
8.35E-4
1.757E+0
7.12E-3
1.876E-9
4.039E-5
1.034E-5
1.61E-5
8.577E-5
1.975E-1
RESULTS OF THE LCA - RESOURCE USE: 1 kg of gypsum based mineral plasters
Parameter
Unit
A1 - A3
C4
Renewable primary energy as energy carrier
Renewable primary energy resources as material utilization
Total use of renewable primary energy resources
Non renewable primary energy as energy carrier
Non renewable primary energy as material utilization
Total use of non renewable primary energy resources
Use of secondary material
Use of renewable secondary fuels
Use of non renewable secondary fuels
Use of net fresh water
[MJ]
[MJ]
[MJ]
[MJ]
[MJ]
[MJ]
[kg]
[MJ]
[MJ]
[m³]
1.046E-1
0
1.046E-1
1.757E+0
0
1.757E+0
1.369E-3
1.467E-3
0
1.467E-3
1.975E-1
0
1.975E-1
2.075E-4
RESULTS OF THE LCA – OUTPUT FLOWS AND WASTE CATEGORIES:
1 kg of gypsum based mineral plasters
5
Parameter
Unit
A1 - A3
C4
Hazardous waste disposed
Non hazardous waste disposed
Radioactive waste disposed
Components for re-use
Materials for recycling
Materials for energy recovery
Exported electrical energy
Exported thermal energy
[kg]
[kg]
[kg]
[kg]
[kg]
[kg]
[MJ]
[MJ]
2.161E-5
1.034E-3
-
1.0E+0
-
Environmental Product Declaration Dalsan Gypsum Industry and Trade Inc. – Gypsum based construction and industrial
plasters
References
Institut Bauen und Umwelt 2011
Institut Bauen und Umwelt e.V., Königswinter (pub.):
Generation of Environmental Product Declarations
(EPDs);
General principles
for the EPD range of Institut Bauen und Umwelt e.V.
(IBU), 2011-09
www.bau-umwelt.de
PCR 2011, Part A
Institut Bauen und Umwelt e.V., Königswinter (pub.):
Product Category Rules for Construction Products
from the range of Environmental Product Declarations
of Institut Bauen und Umwelt (IBU), Part A: Calculation
Rules for the Life Cycle Assessment and
Requirements on the Background Report. September
2012
www.bau-umwelt.de
ISO 14025
DIN EN ISO 14025:2011-10: Environmental labels and
declarations — Type III environmental declarations —
Principles and procedures
framework (ISO 14040:2006) and Requirements and
guidelines (ISO 14044:2006)
PCR 2011, Part B
PCR Guidance-Texts for Building-Related Products
and Services, from the range of Environmental Product
Declarations of Institut Bauen und Umwelt (IBU), Part
B: Requirements on the EPD for mineral factory-made
mortar, June 2012, www.bau-umwelt.de
Ecoinvent
Ecoinvent Centre, www.ecoinvent.org
SimaPro
SimaPro LCA Package, Pré Consultants, the
Netherlands, www.pre-sustainability.com
TS EN 13279-1
Gypsum binders and gypsum plasters - Part 1:
Definitions and requirements
TS EN 13279-2
Gypsum binders and gypsum plasters - Part 2: Test
methods
EN 15804
EN 15804:2012-04: Sustainability of construction
works — Environmental Product Declarations — Core
rules for the product category of construction products
TS EN 13963
Jointing materials for gypsum plasterboards Definitions, requirements and test methods
ISO 9001
DIN EN ISO 9001, Quality Management SystemRequirements
TS EN 14496
Gypsum based adhesives for thermal/acoustic
insulation composite panels and plasterboards Definitions, requirements and test methods
ISO 14040-44
DIN EN ISO 14040:2006-10, Environmental
management - Life cycle assessment - Principles and
GREENGUARD Certification
www.GREENGUARD.org
6
Environmental Product Declaration Dalsan Gypsum Industry and Trade Inc. – Gypsum based construction and industrial
plasters
Publisher
Institut Bauen und Umwelt e.V.
Rheinufer 108
53639 Königswinter
Germany
Tel
Fax
Mail
Web
+49 (0)2223 29 66 79- 0
+49 (0)2223 29 66 79- 0
[email protected]
www.bau-umwelt.com
Programme holder
Institut Bauen und Umwelt e.V.
Rheinufer 108
53639 Königswinter
Germany
Tel
Fax
Mail
Web
+49 (0)2223 29 66 79- 0
+49 (0)2223 29 66 79- 0
[email protected]
www.bau-umwelt.com
Owner of the Declaration
Dalsan Gypsum Industry and Trade
Inc.
1.cadde, Sincap sokak, Büyüksanayi
No:12
06060 Ankara
Turkey
Tel
Fax
Mail
Web
+90 312 303 49 49
+90 312 341 25 69
[email protected]
www.dalsan.com.tr
Author of the Life Cycle Assessment
Metsims Sustainability Consulting
Clear Water Place 4
OX27NL Oxford
UnitedKingdom
Tel
Fax
Mail
Web
+44 755 735 14 76
+44 186 551 04 78
[email protected]
www.metsims.com