F-80 SHOOtInG StaR

KIT 5311
11
decal placement
85531100200
f-80 shooting star™
The Lockheed F-80 Shooting Star
™was the first turbojet fighter accepted
to serve in operational strength with
the U.S. Air Force. The F-80 was not
only elegant, but extremely fast and
agile as well, with it's Allison J-33
gas turbine engine it was capable of
reaching speeds in excess of 550 mph.
Your Monogram model features
detailed landing gear, removable panel
for machine gun bay and complete
tail section can be removed to show
detailed turbojet engine. Canopy
can be in open or closed position to
show the detailed cockpit and pilot
plus optional pylon mounted wing
tanks or bombs and authentic decals
for two versions are also included.
* REPEAT SEVERAL TIMES * REPEAT PROCEDURE * OPTIONAL PARTS
* DECAL
* ASSEMBLY CAUTION * CEMENT TOGETHER * REMOVE AND THROW AWAY * DO NOT CEMENT
` ` LE PROCEDE
` ` * PIECES EN OPTION * DECAL COMANIE *ATTENTION`D ASSEMBLEE
* A REPETER PLUSIEURS FOIS * REPETEZ
* NE PAS COLLER
* A RETIRER ET JETER
* A COLLER
READ THIS BEFORE YOU BEGIN
* Study the assembly drawings.
* Each plastic part is identified by a number.
* In the assembly drawings, some parts will be
marked by a star (★) to indicate chrome
plated plastic.
* For better paint and decal adhesion, wash
the plastic parts in a mild detergent solution.
Rinse and let air dry.
* Check the fit of each piece before
cementing in place.
* Use only cement for polystyrene plastic.
* Scrape plating and paint from areas
to be cemented.
* Allow paint to dry thoroughly before
handling parts.
* Any unused parts may be discarded.
LIRE CE QUI SUIT AVANT DE COMMENCER
* Etudier les schémas de montage.
* Chaque pièce en plastique est identifiée par un numéro.
* Sur les schémas de montage, certaines pièces sont
marquées d'une étoile (★) pour indiquer qu'elles sont en
plastique chromé.
* Pour une meilleure prise de la peinture et des autocollants,
laver les pièces en plastique avec une solution détergente peu
concentrée. Les rincer et les laisser sécher à l'air.
* Vérifier que chaque pièce s'ajuste bien avant
de la coller en place.
* N'utiliser que de la colle pour polystyrène.
* Gratter les parties à coller pour enlever le chrome et la peinture.
* Laisser la peinture bien sécher avant de manipuler les pièces.
* Toute pièce inutilisée peut être jetée.
DECAL APPLICATION INSTRUCTIONS
DIRECTIVES D'APPLICATION DES AUTOCOLLANTS
1. Cut desired decal from sheet.
2. Dip decal in water for a few seconds.
3. Place wet decal on paper towel.
4. Wait until decal is movable on paper backing.
5. Place decal in position on model, face up and
slide backing away.
6. Press out air bubbles with a soft damp cloth.
7. Milkiness that may appear is for better decal
adhesion and will dry clear. Wipe away any
excess adhesive.
8. Do not touch decal until fully dry.
9. Allow the decals 48 hours to dry before
applying clear coat.
1. Découper l'autocollant désiré de la feuille.
2. Tremper l'autocollant dans de l'eau pendant quelques secondes.
3. Placer l'autocollant mouillé sur une serviette en papier.
4. Attendez que l'autocollant puisse être déplacé sur son
support en papier.
5. Mettre l'autocollant en position sur le modèle face sur
le dessus et faire glisser le support pour l'enlever.
6. Appuyer avec un chiffon doux humide pour éliminer les bulles d'air.
7. La substance laiteuse qui peut apparaître est destinée à
améliorer l'adhésion de l'autocollant et devient incolore au
séchage. Essuyer pour enlever tout excédent d'adhésif.
8. Ne pas toucher l'autocollant tant qu'il n'est pas bien sec.
9. Laisser l'autocollant sécher pendant 48 heures avant
d'appliquer une couche transparente.
NOTE: Decals are compatible with
setting solutions or solvents.
REMARQUE: Les autocollants sont compatibles avec
les solutions de fixage ou les solvants.
This paint guide is provided to complete this kit
as shown on the box.
Ce guide de peintures est fourni pour reproduire le modèle
réduit qui apparaît sur la boîte.
Light Brown
Brun clair
Semi Gloss Black
Noir satiné
Yellow
Jaune
Red
Rouge
Gull Gray
Gris cendré
Olive Drab
Gris vert
White
Blanc mat
Aluminum
Aluminum
Flesh
Chair
Steel
Acier
Green
Vert
Zinc Chromate
Vert de zinc
If you have any questions or comments, call our hotline at: (800) 833-3570
or, please write to:
Revell Inc Consumer Service Department, 1850 Howard Street Unit A, Elk Grove Village, Illinois 60007
Be sure to include the plan number (85531100200), part number, description, your return address and phone number.
Kit 5311 - Page 8
Visit our website: www.revell.com
Revell Inc Elk Grove Village, IL. Copyright © 2010. All rights reserved.
1
9
COCKPIT ASSEMBLY
cradle / final assembly
LIGHT BROWN
11
INSTRUMENT PANEL
BLACK PANEL WITH
SILVER DETAILS
36R
RIGHT TOP
BRACE
SEMI GLOSS
BLACK
DECAL
1
37R
RIGHT
CRADLE SIDE
35R
REAR
CRADLE ASSEMBLY
YELLOW
YELLOW
12
SEAT
YELLOW
SEMI
GLOSS
BLACK
SEMI
GLOSS
BLACK
36L
LEFT TOP
BRACE
YELLOW
ZINC CHROMATE
13
SEAT BACK
ZINC CHROMATE
14
CONTROL STICK
ZINC CHROMATE
FLAT
BLACK
26
FUSELAGE
BULKHEAD
SEMI GLOSS
BLACK
SEMI
GLOSS
BLACK
10
COCKPIT
ZINC CHROMATE
35F
FRONT
CRADLE ASSEMBLY
YELLOW
ZINC CHROMATE
10
16A
PILOT ARM
OLIVE DRAB
SEMI GLOSS
BLACK
(WHEELS)
SEMI GLOSS
BLACK
(WHEELS)
37L
LEFT
CRADLE SIDE
YELLOW
decal placement
WHITE
FLESH
SILVER
BUCKLES
YELLOW
FLESH
SEMI GLOSS
BLACK
SILVER
BUCKLES
16
PILOT
OLIVE DRAB
(SUIT)
SEMI
GLOSS
BLACK
FLESH
READ ALL DECAL PLACEMENT GUIDES CAREFULLY TO BECOME
FAMILIER WITH DECAL LOCATIONS BEFORE APPLYING ANY DECALS
Kit 5311 - Page 2
Kit 5311 - Page 7
7 REAR FUSELAGE / EXHAUST ASSEMBLY
2L
LEFT
REAR FUSELAGE
2R
RIGHT
REAR FUSELAGE
ZINC CHROMATE
INSIDE ONLY
27L
LEFT
HORIZONTAL
STABLIZER
2
FRONT FUSELAGE ASSEMBLY
42
MACHINE
GUN BARRELS
1R
RIGHT
FRONT FUSELAGE
STEEL
25R
RIGHT
INTAKE DUCT
27R
RIGHT
HORIZONTAL
STABLIZER
ALUMINUM
19R
RIGHT
ENGINE EXHAUST
STEEL
TAB & NOTCH
42
MACHINE
GUN BARREL
STEEL
8
NOSE GEAR
WELL
ZINC CHROMATE
INSIDE ONLY
19L
LEFT
ENGINE EXHAUST
completed
COCKPIT
SEMI GLOSS BLACK
INSIDE ONLY
STEEL
25L
LEFT
INTAKE DUCT
ALUMINUM
8
gun door / canopy assembly
3
GUN COMPARTMENT DOOR
42
MACHINE
GUN BARREL
STEEL
12
CANOPY
ZINC CHROMATE
INSIDE ONLY
CLEAR WITH
ALUMINUM TRIM
15
CANOPY
FRAME
ALUMINUM
1L
LEFT
FRONT FUSELAGE
11
WINDSHIELD
CLEAR WITH
ALUMINUM
TRIM
ZINC CHROMATE
FRONT VIEW
17
JET ENGINE
STEEL
4
AMMUNITION / GUN
STEEL
Kit 5311 - Page 6
ZINC CHROMATE
Kit 5311 - Page 3
3
5
WING ASSEMBLY
SEMI GLOSS
BLACK
21L
LEFT
WING TOP
21R
RIGHT
WING TOP
NOSE wheel assembly
9
NOSE DOOR ACTUATOR
7
NOSE WHEEL
ZINC CHROMATE
INSIDE ONLY
SEMI GLOSS BLACK
(STEEL CENTER)
5L
LEFT NOSE GEAR DOOR
ZINC CHROMATE
INSIDE ONLY
5R
RIGHT NOSE GEAR
DOOR
ZINC CHROMATE
INSIDE ONLY
22R
RIGHT FLAP
6
NOSE GEAR
ZINC CHROMATE
ALUMINUM
22L
LEFT FLAP
ZINC CHROMATE
18
LANDING
LIGHTS
ALUMINUM
WHITE
20
WING BOTTOM
4
MAIN WHEEL / dive brake
28L
LEFT MAIN
GEAR STRUT
29
MAIN WHEEL
ALUMINUM
SEMI GLOSS BLACK
(STEEL CENTER)
31L
LEFT
MAIN GEAR DOOR
ZINC CHROMATE
INSIDE ONLY
28R
RIGHT MAIN
GEAR STRUT
ALUMINUM
ASSEMBLY
41R (41L)
WING TANK
40R (40L)
1000 POUND BOMB
OLIVE DRAB
OLIVE DRAB
SEMI GLOSS BLACK
(STEEL CENTER)
ZINC CHROMATE
INSIDE ONLY
ZINC CHROMATE
INSIDE ONLY
BOMB / TANK assembly
29
MAIN WHEEL
32R
RIGHT INNER DOOR
32L
LEFT INNER DOOR
6
WHITE
39B
NAPALM TANK
10
SUPPORT
POST
FOR PYLONS
CLEAR
OLIVE DRAB
34R (34L)
TIP TANK
OLIVE DRAB
40R (40L)
1000 POUND BOMB
31R
RIGHT MAIN GEAR
DOOR
41R (41L)
WING TANK
ALUMINUM
FOR WINGS
OLIVE DRAB
ZINC CHROMATE
INSIDE ONLY
39T
NAPALM TANK
33R (33L)
TIP TANK
OLIVE DRAB
ALUMINUM
30L
LEFT OUTER DOOR
ZINC CHROMATE
INSIDE ONLY
30R
RIGHT OUTER DOOR
right
ZINC CHROMATE
INSIDE ONLY
ZINC CHROMATE
INSIDE ONLY
wheels and
doors not
shown for
clarity
23R
RIGHT DIVE BRAKE
ZINC CHROMATE
INSIDE ONLY
1000 POUND BOMB
NAPALM TANK
NAPALM TANK
1000 POUND BOMB
left
ZINC CHROMATE
INSIDE ONLY
23L
LEFT DIVE BRAKE
ZINC CHROMATE
INSIDE ONLY
24
BRAKE SUPPORT
ZINC CHROMATE
38
PYLON
ALUMINUM
24
BRAKE SUPPORT
TIP TANK
TIP TANK
38
PYLON
ALUMINUM
ZINC CHROMATE
ZINC CHROMATE
Kit 5311 - Page 4
WING TANK
WING TANK
Kit 5311 - Page 5
3
WING ASSEMBLY
SEMI GLOSS
BLACK
5
21L
LEFT
WING TOP
21R
RIGHT
WING TOP
NOSE wheel assembly
9
NOSE DOOR ACTUATOR
7
NOSE WHEEL
ZINC CHROMATE
INSIDE ONLY
SEMI GLOSS BLACK
(STEEL CENTER)
5L
LEFT NOSE GEAR DOOR
ZINC CHROMATE
INSIDE ONLY
5R
RIGHT NOSE GEAR
DOOR
ZINC CHROMATE
INSIDE ONLY
22R
RIGHT FLAP
6
NOSE GEAR
ZINC CHROMATE
ALUMINUM
22L
LEFT FLAP
ZINC CHROMATE
18
LANDING
LIGHTS
ALUMINUM
WHITE
20
WING BOTTOM
4
MAIN WHEEL / dive brake
28L
LEFT MAIN
GEAR STRUT
29
MAIN WHEEL
ALUMINUM
SEMI GLOSS BLACK
(STEEL CENTER)
31L
LEFT
MAIN GEAR DOOR
ZINC CHROMATE
INSIDE ONLY
28R
RIGHT MAIN
GEAR STRUT
ALUMINUM
ASSEMBLY
41R (41L)
WING TANK
OLIVE DRAB
40R (40L)
1000 POUND BOMB
OLIVE DRAB
SEMI GLOSS BLACK
(STEEL CENTER)
ZINC CHROMATE
INSIDE ONLY
ZINC CHROMATE
INSIDE ONLY
BOMB / TANK assembly
29
MAIN WHEEL
32R
RIGHT INNER DOOR
32L
LEFT INNER DOOR
6
WHITE
39B
NAPALM TANK
10
SUPPORT
POST
FOR PYLONS
CLEAR
OLIVE DRAB
34R (34L)
TIP TANK
OLIVE DRAB
40R (40L)
1000 POUND BOMB
31R
RIGHT MAIN GEAR
DOOR
41R (41L)
WING TANK
ALUMINUM
FOR WINGS
OLIVE DRAB
ZINC CHROMATE
INSIDE ONLY
39T
NAPALM TANK
33R (33L)
TIP TANK
OLIVE DRAB
ALUMINUM
30L
LEFT OUTER DOOR
ZINC CHROMATE
INSIDE ONLY
30R
RIGHT OUTER DOOR
right
ZINC CHROMATE
INSIDE ONLY
ZINC CHROMATE
INSIDE ONLY
wheels and
doors not
shown for
clarity
1000 POUND BOMB
NAPALM TANK
NAPALM TANK
1000 POUND BOMB
left
ZINC CHROMATE
INSIDE ONLY
23R
RIGHT DIVE BRAKE
ZINC CHROMATE
INSIDE ONLY
23L
LEFT DIVE BRAKE
ZINC CHROMATE
INSIDE ONLY
38
PYLON
24
BRAKE SUPPORT
ZINC CHROMATE
ALUMINUM
TIP TANK
TIP TANK
38
PYLON
ALUMINUM
24
BRAKE SUPPORT
ZINC CHROMATE
ZINC CHROMATE
Kit 5311 - Page 4
WING TANK
WING TANK
Kit 5311 - Page 5
7 REAR FUSELAGE / EXHAUST ASSEMBLY
2L
LEFT
REAR FUSELAGE
2R
RIGHT
REAR FUSELAGE
ZINC CHROMATE
INSIDE ONLY
27L
LEFT
HORIZONTAL
STABLIZER
2
FRONT FUSELAGE ASSEMBLY
42
MACHINE
GUN BARRELS
1R
RIGHT
FRONT FUSELAGE
25R
RIGHT
INTAKE DUCT
STEEL
27R
RIGHT
HORIZONTAL
STABLIZER
ALUMINUM
19R
RIGHT
ENGINE EXHAUST
STEEL
TAB & NOTCH
42
MACHINE
GUN BARREL
STEEL
8
NOSE GEAR
WELL
ZINC CHROMATE
INSIDE ONLY
19L
LEFT
ENGINE EXHAUST
completed
COCKPIT
SEMI GLOSS BLACK
INSIDE ONLY
STEEL
25L
LEFT
INTAKE DUCT
ALUMINUM
8
gun door / canopy assembly
3
GUN COMPARTMENT DOOR
42
MACHINE
GUN BARREL
STEEL
12
CANOPY
ZINC CHROMATE
INSIDE ONLY
CLEAR WITH
ALUMINUM TRIM
15
CANOPY
FRAME
ALUMINUM
1L
LEFT
FRONT FUSELAGE
11
WINDSHIELD
CLEAR WITH
ALUMINUM
TRIM
ZINC CHROMATE
FRONT VIEW
17
JET ENGINE
STEEL
4
AMMUNITION / GUN
STEEL
Kit 5311 - Page 6
ZINC CHROMATE
Kit 5311 - Page 3
1
COCKPIT ASSEMBLY
9
cradle / final assembly
LIGHT BROWN
11
INSTRUMENT PANEL
BLACK PANEL WITH
SILVER DETAILS
36R
RIGHT TOP
BRACE
SEMI GLOSS
BLACK
DECAL
1
37R
RIGHT
CRADLE SIDE
35R
REAR
CRADLE ASSEMBLY
YELLOW
YELLOW
12
SEAT
YELLOW
SEMI
GLOSS
BLACK
SEMI
GLOSS
BLACK
36L
LEFT TOP
BRACE
YELLOW
ZINC CHROMATE
13
SEAT BACK
ZINC CHROMATE
14
CONTROL STICK
ZINC CHROMATE
FLAT
BLACK
26
FUSELAGE
BULKHEAD
SEMI GLOSS
BLACK
SEMI
GLOSS
BLACK
10
COCKPIT
ZINC CHROMATE
35F
FRONT
CRADLE ASSEMBLY
YELLOW
ZINC CHROMATE
10
16A
PILOT ARM
OLIVE DRAB
SEMI GLOSS
BLACK
(WHEELS)
SEMI GLOSS
BLACK
(WHEELS)
37L
LEFT
CRADLE SIDE
YELLOW
decal placement
WHITE
FLESH
SILVER
BUCKLES
YELLOW
FLESH
SEMI GLOSS
BLACK
SILVER
BUCKLES
16
PILOT
OLIVE DRAB
(SUIT)
SEMI
GLOSS
BLACK
FLESH
READ ALL DECAL PLACEMENT GUIDES CAREFULLY TO BECOME
FAMILIER WITH DECAL LOCATIONS BEFORE APPLYING ANY DECALS
Kit 5311 - Page 2
Kit 5311 - Page 7
11
KIT 5311
decal placement
85531100200
f-80 shooting star™
The Lockheed F-80 Shooting Star
™was the first turbojet fighter accepted
to serve in operational strength with
the U.S. Air Force. The F-80 was not
only elegant, but extremely fast and
agile as well, with it's Allison J-33
gas turbine engine it was capable of
reaching speeds in excess of 550 mph.
Your Monogram model features
detailed landing gear, removable panel
for machine gun bay and complete
tail section can be removed to show
detailed turbojet engine. Canopy
can be in open or closed position to
show the detailed cockpit and pilot
plus optional pylon mounted wing
tanks or bombs and authentic decals
for two versions are also included.
* REPEAT SEVERAL TIMES * REPEAT PROCEDURE * OPTIONAL PARTS
* DECAL
* ASSEMBLY CAUTION * CEMENT TOGETHER * REMOVE AND THROW AWAY * DO NOT CEMENT
` ` LE PROCEDE
` ` * PIECES EN OPTION * DECAL COMANIE *ATTENTION`D ASSEMBLEE
* A REPETER PLUSIEURS FOIS * REPETEZ
* NE PAS COLLER
* A RETIRER ET JETER
* A COLLER
READ THIS BEFORE YOU BEGIN
* Study the assembly drawings.
* Each plastic part is identified by a number.
* In the assembly drawings, some parts will be
marked by a star (★) to indicate chrome
plated plastic.
* For better paint and decal adhesion, wash
the plastic parts in a mild detergent solution.
Rinse and let air dry.
* Check the fit of each piece before
cementing in place.
* Use only cement for polystyrene plastic.
* Scrape plating and paint from areas
to be cemented.
* Allow paint to dry thoroughly before
handling parts.
* Any unused parts may be discarded.
LIRE CE QUI SUIT AVANT DE COMMENCER
This paint guide is provided to complete this kit
as shown on the box.
* Etudier les schémas de montage.
* Chaque pièce en plastique est identifiée par un numéro.
* Sur les schémas de montage, certaines pièces sont
marquées d'une étoile (★) pour indiquer qu'elles sont en
plastique chromé.
* Pour une meilleure prise de la peinture et des autocollants,
laver les pièces en plastique avec une solution détergente peu
concentrée. Les rincer et les laisser sécher à l'air.
* Vérifier que chaque pièce s'ajuste bien avant
de la coller en place.
* N'utiliser que de la colle pour polystyrène.
* Gratter les parties à coller pour enlever le chrome et la peinture.
* Laisser la peinture bien sécher avant de manipuler les pièces.
* Toute pièce inutilisée peut être jetée.
Ce guide de peintures est fourni pour reproduire le modèle
réduit qui apparaît sur la boîte.
DECAL APPLICATION INSTRUCTIONS
DIRECTIVES D'APPLICATION DES AUTOCOLLANTS
1. Cut desired decal from sheet.
2. Dip decal in water for a few seconds.
3. Place wet decal on paper towel.
4. Wait until decal is movable on paper backing.
5. Place decal in position on model, face up and
slide backing away.
6. Press out air bubbles with a soft damp cloth.
7. Milkiness that may appear is for better decal
adhesion and will dry clear. Wipe away any
excess adhesive.
8. Do not touch decal until fully dry.
9. Allow the decals 48 hours to dry before
applying clear coat.
1. Découper l'autocollant désiré de la feuille.
2. Tremper l'autocollant dans de l'eau pendant quelques secondes.
3. Placer l'autocollant mouillé sur une serviette en papier.
4. Attendez que l'autocollant puisse être déplacé sur son
support en papier.
5. Mettre l'autocollant en position sur le modèle face sur
le dessus et faire glisser le support pour l'enlever.
6. Appuyer avec un chiffon doux humide pour éliminer les bulles d'air.
7. La substance laiteuse qui peut apparaître est destinée à
améliorer l'adhésion de l'autocollant et devient incolore au
séchage. Essuyer pour enlever tout excédent d'adhésif.
8. Ne pas toucher l'autocollant tant qu'il n'est pas bien sec.
9. Laisser l'autocollant sécher pendant 48 heures avant
d'appliquer une couche transparente.
NOTE: Decals are compatible with
setting solutions or solvents.
REMARQUE: Les autocollants sont compatibles avec
les solutions de fixage ou les solvants.
Light Brown
Brun clair
Semi Gloss Black
Noir satiné
Yellow
Jaune
Red
Rouge
Gull Gray
Gris cendré
Olive Drab
Gris vert
White
Blanc mat
Aluminum
Aluminum
Flesh
Chair
Steel
Acier
Green
Vert
Zinc Chromate
Vert de zinc
If you have any questions or comments, call our hotline at: (800) 833-3570
or, please write to:
Revell Inc Consumer Service Department, 1850 Howard Street Unit A, Elk Grove Village, Illinois 60007
Be sure to include the plan number (85531100200), part number, description, your return address and phone number.
Kit 5311 - Page 8
Visit our website: www.revell.com
Revell Inc Elk Grove Village, IL. Copyright © 2010. All rights reserved.