Ionic Energizer Foot Spa

INSTRUCTIONS:
Place the liner in the bowl. Fill the bowl up to the “fill line” about half way up with
warm water. Hot water is too conductive and also opens the pores of the feet to
the gunk floating around. Cold water will not dissolve the salt properly and
ionization is difficult to get started. The level of the water should be approximately level with the middle of the arrays. (See figure B). When placing feet
inside foot spa, water should rise between the third and fourth line of the arrays.
If water is too low adjust accordingly.(See figure B)
.
NOTE : IF THE BOWL IS OVERFILLED, THE UNIT WILL AUTOMATICALLY TURN OFF.
OVERFILLING THE BOWL COULD CAUSE DAMAGE TO THE ELECTRICAL
COMPONENTS.
Now add 0.3g or 0.5oz of low sodium salt. (One teaspoon) Make sure that the
salt is completely dissolved before treatment begins. Press the on button and
the whole process will start automatically and end automatically. If there is too
much salt the warning light will go on. If light is on, turn unit off, empty unit and
clean thoroughly, then refill with water and the proper amount of salt.
During the 30 minute treatment, the VIATEK IONIC ENERGIZER Foot SPA will
begin to help rebalance the positive and negative ions in your body. It is
important to drink at least 500ml of water during the treatment. You will notice
the water will change color throughout the treatment. This is perfectly normal.
Most of this color change is due to the reaction of the arrays with the salt
solution.
model IE100
WARNING:
Do Not use the VIATEK IONIC SPA
If you use a cardiac pacemaker.
If you suffer from any form of epilepsy.
If you are pregnant unless medically advised.
On children under 5 years old.
If you are suffering from an unknown illness.
Consult your physician before use.
DO NOT immerse the instrument in water or any
other liquid substance.
This unit should only be used for the purpose
which is described in these instructions.
Ionic Energizer Foot Spa
Directions for Use
DISCLAIMER:
VIATEK or its partners accepts no responsibility whatsoever for any
damage or injury caused by the misuse of the VIATEK IONIC SPA
product or failure to follow the instructions set out in this leaflet or any
other subsequent documents relating to this product.
Only use the supplied 12V power supply.
You may also see deposits floating on top of the water. Again, this is perfectly
normal as one of the benefits of a VIATEK treatment is lymphatic drainage.The
arrays will usually last for between 30 and 40 treatments. When the arrays stop
working there will be no color change to the water. It is time to change the
arrays. Additional Arrays are available from VIATEK or your local dealer.
Keep your VIATEK IONIC SPA clean by wiping over with soapy water and allow
to dry naturally.
US: viatekproducts.com
UK: viatekgroup.com
888-7VIATEK
407.248.0123
011 +44.207.350.2020
WARNING:
Disassembly of the electronic components within
this unit may result in exposure to lead in the form
or
of a solder , which is known to to state of California to
cause cancer, birth defects and other reproductive harm.
(3)
made in china
revinsIE100/0706
Assembling The Ionic Foot Spa:
Place the Massage Bubble Foot Plate into the
Foot Bowl.
Fully assembled unit
A.
Turn the control unit over, and attach the
arrays. The arrays will slide into the holes
located on the underside of the control unit.
NOTICE:
Attach each of the pieces marked A into the
holes marked A. Attached each of the piece
marked B to holes marked B.
After the Arrays have been slid into place.
Attach the control unit and arrays to the Foot
Bowl aligning the Arrays with the corresponding cutouts in the Massage Bubble Foot Plate.
Foot bowl
WARNING:
Never pick up Foot Spa by the Control Unit.
Handle is only to disassemble and
assemble the unit.
Bubble massage foot plate
Dual Arrays
US: viatekproducts.com
UK: viatekgroup.com
888-7VIATEK
in between 3rd
and 4th line
of array
(feet in)
For questions on how to assemble the Viatek
Ionic Energizer Foot Spa visit:
Control Unit
888-7 VIATEK
B.
407.248.0123
011 +44.207.350.2020
(1)
www.ionicenergizer.com
Click the link too see the energizer kit.
see figure A for assembly.
US: viatekproducts.com
UK: viatekgroup.com
888-7VIATEK
level with middle
of array
(feet out)
407.248.0123
011 +44.207.350.2020
(2)