IMZ Implant System - Swiss NF Metals Inc

Transcription

The IMZ® Implant System
Compatible Components
T
he IMZ Implant System was developed in Germany by Dr. Axel Kirsch in the early 1970’s.
IMZ is the only major implant system using a shock absorbing intermobile element designed
to simulate the periodontal ligament. Two types of implants were made—the IMZ Original nonhex and the IMZ Hex Head external hex (Branemark RP compatible).
■ IMZ Original 3.3 & 4.0 non-hex
■ IMZ Hex Head 3.3 & 4.0 external hex
IMZ - Original
IMZ Original
The original IMZ implant was manufactured in two diameters – 3.3mm and 4.0mm. The internal thread of the 3.3mm implant is 2.3mm and the 4.0mm implant has a 3.0mm internal
thread. The external implant body is either titanium plasma sprayed or HA coated with
hydroxalappetite. The IMZ implant body is no longer sold, however, IMZ restorative components, such as the IME, IMC, and UMA are still available from Attachments International.
IMZ Hex Head - Branemark RP Compatible
The IMZ Hex Head implant also manufactured in two diameters – 3.3mm and 4.0mm was
added in 1991. Both are restoratively compatible with the Branemark Regular Platform implant.
For restorative compatible components refer to the Branemark section of this manual.
IMZ - Hex Head
Compatible components made by Attachments International are available for:
Implants
Restoratively Compatible To
■ IMZ Original 3.3 & 4.0 non-hex
none
■ IMZ Hex Head 3.3 & 4.0 external hex
Branemark®, Regular Platform 4.1
3i Minimplant® & Standard Osseotite®
Implamed® RP
Innova Entegra® 3.25 & 4.0
REmark-ST RP
Steri-Oss® Hex-Loc 3.8 & 4.5
Restore® RD & Sustain® RD
Taper-Lock®
Refer to Branemark RP Section for
compatible IMZ Hex Head
components
IMZ Original
Non-Hex
ø4.0mm
2.3mm
Thread
Diameter
3.0mm
Thread
Diameter
2.7mm
3.4mm
External
Hex
2.7mm
2.3mm
Thread
3.0mm
Thread
2.0mm
Thread
IMZ Original
Non-Hex
Implant Diameter 4.0
2.0mm
Thread
Diameter
IMZ Hex Head
Branemark RP
Compatible
Implant Diameters
3.3 & 4.0
All product names referenced herein are trademarks of their
respective companies, refer to inside back cover of this manual.
© Copyright 2007 Attachments International, Inc., San Mateo, CA
249
IMZ
Implant Diameter 3.3
ø4.1mm
Platform
ø3.3mm
Terminology of Components
Page Header Sample Guide
IMZ 3.3 & 4.0
Direct
Healing Caps
Implant Analog
To The Implant
Components listed on page
Restoration Connection
Compatible Implant Name
Restorative Components:
For ease in selecting components, the Branemark Section is divided by Restoration Connection:
• Direct To The Implant —or—
• Indirect To An Intermediate Component (Tissue Extensions/Abutments).
Overdenture Attachments, Bar Systems, Indirect Individual Parts and Tools are found
NEW: 7 IMZ REFERENCE CHARTS are found at end of
following in the Indirect Section.
this section to illustrate the complex relationship of the IMZ - IME - IMC components.
Direct
To The Implant
Indirect
Components
The Direct Restorative Components are the elements used to fabricate a restoration that
will be connected directly to the implant(s).
The Indirect / Intermediate Restorative Components fit to an intermediate tissue extension
(abutment) which in turn is connected to the implant(s).
Implant Body:
The implant body is surgically placed into the bone. One surgical method traditionally involved a two-stage surgery, leaving the implant unloaded in the bone to
allow for osseointegration, followed by tissue surgery to uncover the implant
before the restorative components are added. Another method, called Immediate
Loading, is a one-stage surgery where the abutment and restoration are attached
to the implant at the time of implant placement.
IMZ - Original
Intermediate Connector / Tissue Extension / IME / TIE:
The TE (Tissue Extension) is the intermediate connector between the implant and
the restoration, it may extend above the tissue. In some instances, a TE extension
is subgingival, to provide a more esthetic restoration.
The original IMZ tissue extension was the plastic IME (Inter Mobile Element) with
the metal TIE.
IME & TIE
Implant Standardization:
The UMA tissue extension was developed to standardize the components and
instruments for many different implant allowing for an economical inventory and
for simplicity of restorative procedures. Its tapered/hexagon fitting surface is identical, regardless of the size or type of implant employed, while its screw-in base is
implant specific.
UMA
Compatibility:
Implants
Restoratively Compatible To
n IMZ Original 3.3 & 4.0 non-hex
none
n IMZ Hex Head 3.3 & 4.0 external hex
Refer to NOBELBranemark RP Section
for compatible IMZ Hex Head
components
All product names referenced herein are trademarks of their respective companies.
248
Branemark, Regular Platform 4.1
3i Minimplant & Standard Osseotite
Implamed RP
Innova Entegra 3.25 & 4.0
REmark-ST RP
Steri-Oss Hex-Loc 3.8 & 4.5
Taper-Lock
*06ARM 06 3i-IMZ-ITI_H
9/7/07
10:04 AM
Page 251
IMZ® Non-Hex 3.3 & 4.0
Direct
To The Implant
Healing Caps
Impression Copings
Analogs
HEALING CAPS
Healing caps are used to maintain access through tissue
during healing phase. They are available in various heights
to accommodate tissue depth and require the .050" hex driver.
SD Small Implant Diameter IMZ 3.3
MD Medium Implant Diameter IMZ 4.0
3.3
SD
MD
3.3
4.0
Dimensions
Order #
Order #
H=2.0mm
H=4.0mm
H=6.0mm
56-302120
56-302140
56-302160
56-402120
56-402140
56-402160
11-000007
11-000007
4.0
Description
Healing Caps—To Fit Implant
Implant Healing Cap
Implant Healing Cap
Implant Healing Cap
TOOLS
DDS Hex Driver .050"
IMPRESSION COPINGS
Impression copings are used to take an impression of the
implant body. The Impression Copings which fit the implant
bodies are made of titanium and transfer the thread timing.
For the IMZ-Hex Head implant, refer to the Branemark RP
compatible section.
3.3
4.0
Description
SD
MD
3.3
4.0
Order #
Order #
56-300080
56-400080
SD
MD
3.3
4.0
Order #
Order #
56-300015
56-400015
Impression Copings—To Fit Implant
Impression Coping for IMZ
ANALOGS
Analogs are used for the fabrication of a master model.
They are replicas of the implant body.
3.3
4.0
Analogs—To Fit Implant
Implant Body Analog to fit IMZ, Brass
251
To Order: 800-999-3003 • 650-340-0393
Additional Information: www.attachments.com
IMZ
Description
To The Implant
Direct
Titanium Posts
Ti-Blocs
TITANIUM POSTS
The direct titanium abutment posts screw into the implant
body and are indicated for Bridge Restorations only. They
may be secured with Teflon tape or thread adhesive. The
3.3
A
4.0
titanium tapered posts can be altered like a preparation.
Fabricate a soft tissue model whenever preparations are
made in the laboratory.
A
SD
MD
3.3
4.0
Order #
Order #
Direct Titanium Posts (A)
56-301200
56-401200
USE WITH:
Impression Coping
Implant Body Analog
56-300080
56-300015
56-400080
56-400015
Description
REQUIRES .050" HEX DRIVER:
DDS .050" Hex Driver
Lab .050" Driver
BIO-TORQ Tip Hex .050", Short (Use with Bio-Torq Wrench)
BIO-TORQ Tip Hex .050", Long (Use with Bio-Torq Wrench)
11-000007
11-000006
59-100120
59-100125
TI-BLOC
The titanium bloc screws into the non-hexed IMZ implant
body and may be secured with Teflon tape or thread adhesive. The Ti-Bloc requires more preparation as it is a true
cylindrical bloc. However, the Ti-Bloc can be prepared like a
.050"
hex
A
posterior prep, thereby increasing the esthetics and comfort. It can also be prepared to correct for divergency.
Insertion requires .050" hex driver.
.050"
hex
B
SD
MD
3.3
4.0
Description
Dimensions
Order #
Order #
Ti-Bloc 3.3 small (A)
Ti-Bloc 4.0 small (B)
ø=4.7mm
ø=5.0mm
56-301210
—
—
56-401210
56-300080
56-300015
56-400080
56-400015
USE WITH:
Impression Coping
Implant Body Analog
REQUIRES .050" HEX DRIVER:
DDS .050" Hex Driver
Lab .050" Driver
BIO-TORQ Tip Hex .050", Short (Use with Bio-Torq Wrench)
BIO-TORQ Tip Hex .050", Long (Use with Bio-Torq Wrench)
© Copyright 2010 Attachments International, Inc., Burlingame, CA
11-000007
11-000006
59-100120
59-100125
256
To Order: 800-999-3003 • 650-340-0393
Modified IME
IME ABUTMENT
IME Abutments (tissue extensions) are intermediate components made to fit
between the implant and the restoration. The IME, in plastic or Titanium,
requires the Titanium TIE. The Modified IME, in plastic or Titanium, fits
directly to the implant. Restorations can be made on the abutment using
abutment cylinders. The UMA Healing Cap protects the IME until restoration
is delivered. The Impression Coping takes an impression of the abutment
and transfers abutment position and thread timing. The Analog is a replica
of the abutment and is used for fabrication of a master model. The CSP
(Cylinder, Screw & Plug) is used for crown & bridge and bar restorations.
SEE IMZ REFERENCE CHARTS #1 & #2 (at end of IMZ section)
Reference UMA Indirect IMZ page for Healing Caps to fit IME.
Titanium
Titanium
Plastic
Plastic
IME with TIE
3.3
3.3
4.0
4.0
B
A
IME Abutments
Indirect
IME COMPONENTS
4.0
3.3
3.3
Tapered
C
Impression Coping
2 Pc
C
Imp Coping 2pc 3.3
2 Pc
Description
A
IME (Intramobile Element)
IME, Plastic (requires TIE)
IME, Plastic (requires TIE)
IME, Titanium (requires TIE)
IME, Titanium (requires TIE)
A
B
C
Imp Coping 2pc 4.0
D
Analog
Dimensions
Tissue Extension Height
2.0mm
4.0mm
2.0mm
4.0mm
TIE (Transmucosal Implant Extension)
TIE, Titanium (not for Mod. IME)
4.0
E
CSP 3.3mm
E
CSP 4.0mm
Intended Use
SD
MD
3.3
4.0
Order #
Order #
Tissue Extension / Abutment
57-8270U
N/A
57-8273TU
N/A
57-8280U
57-8285U
57-8283TU
57-8288TU
Collar Extension
1.0mm
2.0mm
4.0mm
Modified IME (Modified Intramobile Element)
57-8258A
57-8260A
57-8250A
57-8255A
IME, Plastic (direct to implant)
IME, Titanium (direct to implant)
57-8270MU
57-8273MBU
57-8280MU
57-8283MBU
Impression Coping
Impression Taking / Transfer Timing
Tapered Impression coping, transfer thread timing (closed tray)
Impression coping, 2 piece, transfer thread timing (open tray)
56-000080
56-300095
56-000080
56-400095
Analog
Model Fabrication
IME 3.3 /4.0 Analog, Brass (Replicates both IME & Modified IME)
56-000015
56-000015
56-300252
56-400252
56-000250
56-000270
56-300052
56-000250
56-000270
56-400052
11-000150
40-000150
11-000155
11-000004
59-100150
59-100030
11-000150
40-000150
11-000155
11-000004
59-100150
59-100030
Components—To Fit IME and Modified IME/ Tissue Extension
C
D
E
CSP (Cylinder, Screw & Plug)
IME CSP, Non-Engaging Cylinder, .050" Hex Screw and Plug
Crown & Bridge / Bar Restorations
PARTS
Plastic Cylinder Only, Long for 3.3 or 4.0 (also fits the IMC 3.3 & 4.0)
Plastic Cylinder Only, Short for 3.3 or 4.0 (also fits the IMC 3.3 & 4.0)
IMZ Ti Hex .050" Screw Only (To fit IME and Complete Abutment)
Reamer, UMA Abutment Carbide .0880" (requires Pin Vise 40-000150)
Pin Vise for Carbide Reamers .002 - .130"
UMA, Lapping Tool and Guide Pin
Pin Vise
Friction Grip Driver (for plastic IME)
BIO-TORQ Tip, UMA, Short (for Titanium IME only)
BIO-TORQ Wrench 30 N/cm
253
Reamer
To Order: 800-999-3003
•
650-340-0393
IMZ
TOOLS
IMC ABUTMENTS (Intramobile Connector)
Titanium IMC Connector
3.3
4.0
A
The original IMC (Intramobile Connector) consists of a titanium insert and a plastic element (donut). The Ti IMC is a onepiece titanium abutment that replaces the original titanium
insert and plastic element. The IMC two-piece impression
coping connects to the original plastic IMC or the Ti IMC. The
IMC analog is used to fabricate a working model. Castablemachined plastic cylinders are used in the fabrication of the
screw-retained framework.
SEE IMZ REFERENCE CHARTS #1 - #4 (end of IMZ section)
Ti IMC Connector
IMC COMPONENTS
Note: Thread is only in lower portion of
both the IMC Connector and the IMC
Analog, requiring the longer IMC screw.
Fits:
IME &
IMC
3.3 &
4.0
D
Impression Coping
E
Thread in lower
portion
B
C
F
IMC Titanium Connector
Dimensions
F
Short
Intended Use
IMC Ht
1.0mm
2.0mm
Conversion
3.0mm
4.0mm
Overall Ht
1.8mm
2.8mm
3.5mm
3.8mm
4.8mm
IMC Titanium Insert
IMC Ti Insert (requires IMC Element)
1.0mm
2.0mm
Conversion
3.0mm
4.0mm
1.8mm
2.8mm
3.5mm
3.8mm
4.8mm
3.3
B
C
4.0
IMC Titanium Insert
Fits:
IME & IMC
3.3 & 4.0
Long
Ti IMC, Titanium
Ti IMC, Titanium
Ti IMC, Titanium
Ti IMC, Titanium
Ti IMC, Titanium
Plastic IMC Element
Original
IMC Ti Insert &
IMC Plastic Element
Analog
Description
A
IMC Abutment
Indirect
SD
MD
3.3
4.0
Order #
Order #
57-8317CU
57-8318CU
57-8319CU
57-8320CU
57-8310CU
57-8311CU
57-8312CU
57-8313CU
Insert & Element
57-8162C
57-8163C
57-8170C
57-8175C
57-8171C
IMC Plastic Element
57-8164C
57-8165C
Insert with Abutment
IMC, Intramobile Element, Plastic Bushing ("donut")
57-8104C
57-8104C
57-300090
57-400090
57-300016
57-400016
56-000250
56-000270
56-000250
56-000270
11-000150
40-000150
11-000155
59-100171
59-100030
11-000150
40-000150
11-000155
59-100172
59-100030
Components—To Fit IMC Connector and IMC Insert
D
Impression Coping, 2 Piece
IMC 2 Piece Impression coping, transfers thread timing
E Analog
IMC Analog, Brass
Model Fabrication
PARTS
F
Plastic Cylinder Only, Non-Engaging, Long for 3.3 or 4.0 (also fits the IME 3.3 & 4.0)
Plastic Cylinder Only, Non-Engaging, Short for 3.3 or 4.0 (also fits the IME 3.3 & 4.0)
NOTE: Screws indicated depend on initial IMZ restoration. See Flow Charts #5 & #6 for complete
list of available screws. Contact Technical Support for further information, 650-340-1426.
TOOLS
Reamer, UMA Abutment Carbide .0880" (requires Pin Vise 40-000150)
BIO-TORQ Tip IMZ / IMC, Short
254
To Order: 800-999-3003
•
650-340-0393
IMZ Non-Hex 3.3 & 4.0 Compatible
UMA Abutment
UMA ABUTMENT
4.0
3.3
Indirect
The UMA Abutment (tissue extension) is an
intermediate component made to fit between
the implant and the restoration. The UMA has a
standardized fitting surface, which allows the
UMA restorative components to be interchangeable regardless of the implant type. The UMA
Healing Cap protects the UMA until the restoration is delivered. The Bridge Tapered UMA
Impression Coping transfers the UMA position
A
while the Hex UMA Impression Coping transfers
the hex orientation of the UMA Abutment. The
UMA Analog replicates the UMA for the model.
The UMA Hex or Non-Hex Plastic Cylinders are
used to make frameworks for bridges or bars. The
UMA CAL System is used for a passive fit technique. For restorations the fit directly to the
implant refer to the UCLA System for the specific
implant type.
UMA COMPONENTS
C
B
Healing Cap
Impression Coping
Tapered 1 piece
Description
A
UMA Abutment
UMA, Abutment
UMA, Abutment
UMA, Abutment
UMA, Abutment
UMA, Abutment
UMA, Abutment
UMA, Abutment
UMA, Abutment
C
Impression Coping
Hex 2 piece
E
D
Analog
Brass
CSP
Hex Cyl, Hex screw
Dimensions
Intended Use
Tissue Extension Height
H=0.5mm
H=1.0mm
H=2.0mm
H=3.0mm
H=4.0mm
H=5.0mm
H=6.0mm
H=7.0mm
E
CSP
CAL Cylinder
Non-Hex Cyl, Hex Screw
SD
MD
3.3
4.0
Order #
Order #
N/A
N/A
11-001320
11-001330
11-001340
11-001350
11-001360
11-001370
11-001405
11-001410
11-001420
11-001430
11-001440
11-001450
11-001460
11-001470
Components—To Fit UMA Abutment / Tissue Extension
B
C
D
E
F
Healing Cap
UMA Healing Cap
UMA Healing Cap
UMA Healing Cap
Tissue Healing / Management
H=2.0mm ø=4.5mm
H=4.0mm ø=4.5mm
H=6.0mm ø=4.5mm
One Thread Size Fits All UMAs
11-002120
11-002140
11-002160
Impression Coping
UMA Impression Coping Tapered, one piece
UMA Impression Coping Hex with .050" Hex Guide Pin, two piece
11-000080
11-000090
Analog
UMA Analog, Brass
11-000015
Model Fabrication
11-000202
11-000201
11-000252
11-000251
CAL Cylinder (Passive Fit)
Bars / Fixed Detachable
UMA CAL Cylinder, Ti .050" Hex Screw, Waxing Sleeve & Spacer
11-000452
NOTE: Slot Screws (#11-000051) may be ordered separately.
PARTS
UMA .050" Hex Titanium Screw, only
UMA, Short Bar Cylinder only, Red
11-000052
11-000270
FOR INDIVIDUAL UMA PARTS & TOOLS—Refer to the UMA Section of this Manual.
253
To Order: 800-999-3003 • 650-340-0393
IMZ
CSP (Cylinder, Screw & Plug)
Crown & Bridge / Bar Restorations
UMA Hex Cylinder (blue), Ti .050" Hex Screw & Occlusal Plug
UMA Hex Cylinder (blue), Ti Slot Screw & Occlusal Plug
UMA Non-Hex Cylinder (yellow), Ti .050" Hex Screw & Occlusal Plug
UMA Non-Hex Cylinder (yellow), Ti Slot Screw & Occlusal Plug
Overdenture
Attachments
OVERDENTURE STUD TYPE ATTACHMENTS
Three types of overdenture attachments are most commonly
used to directly screw into the implant—the Dalla Bona, the
ORS, (O-Ring system) and the Locator. Connectors are made
of titanium. Dalla Bona male, ORS male and Locator female
are sold separately by tissue height. The DB Female Kit
DB 3.3
DB 4.0
A
includes 1 adjustable female, 1 spacer and 1 brass analog.
The ORS Female Kit includes 1 gold plated retainer ring, 3
white final & 3 red processing O-Rings and 1 brass analog.
The Locator Male Complete includes 3 plastic color coded
males, a metal housing with black processing male and spacer.
ORS
3.3
A
ORS
4.0
B
C
C
Allegro Implant Female Kit
Optional for DB
Locator
3.3
Locator
4.0
D
D
SD
MD
3.3
4.0
Dimensions
Order #
Order #
Dalla Bona, male only
H=1mm
H=2mm
H=3mm
H=4mm
H=5mm
H=6mm
H=7mm
Dalla Bona, Implant Ti Female: Fe, Spacer & Analog
Fø=3.4mm
Allegro, Implant Female Kit (option for Dalla Bona female) (B)
includes Metal Housing, 4 Females, Implant Spacer & Brass Analog
56-343013
56-343023
56-343033
56-343043
56-343053
56-343063
56-343073
40-430002
40-730002
56-443013
56-443023
56-443033
56-443043
56-443053
56-443063
56-443073
40-430002
40-730002
56-344013
56-344023
56-344033
56-344043
56-344053
56-344063
56-344073
40-440002
56-444013
56-444023
56-444033
56-444043
56-444053
56-444063
56-444073
40-440002
63-008820
63-008820-1
63-008820-2
63-008820-3
63-008820-4
63-008820-5
63-008519
63-008540
63-008547
63-008915
63-008548
63-008830
63-008830-1
63-008830-2
63-008830-3
63-008830-4
63-008830-5
63-008519
63-008540
63-008547
63-008915
63-008548
Description
Dalla Bona System (A)
or
H
ORS, O-Ring System (C)
ORS, male only
H=1mm
ORS, male only
H=2mm
ORS, male only
H=3mm
ORS, male only
H=4mm
ORS, male only
H=5mm
ORS, male only
H=6mm
ORS, male only
H=7mm
ORS, Implant Female Kit, includes Retainer Ring, Analog & O-Rings (6)
H
Locator System (D)
Locator Implant Female only
H=0mm
H=1mm
H=2mm
H=3mm
H=4mm
H=5mm
Locator Male Complete
Locator Extended Range Male Complete
Locator Extended Range Replacement Male, 3 lbs retention, green (4)
Locator Extended Range Replacement Male, 2 lbs retention, orange (4)
Locator Extended Range Replacement Male, 1.5 lbs retention, red (4)
H
PARTS & TOOLS
For Dalla Bona, Allegro, ORS & Locator Parts and Tools, refer to next page.
For IMZ Hex Head 3.3 & 4.0 External Hex compatible components, refer to the Branemark RP / Direct section of this manual.
256
To Order: 800-999-3003
•
650-340-0393
IMZ ® Non-Hex
Dalla Bona, ORS, Locator
3.3 & 4.0 Compatible
Parts & Tools
for Overdenture
Stud Type Attachments
OVERDENTURE STUD TYPE ATTACHMENTS – PARTS & TOOLS
PARTS: Description
Dimensions
Order #
DALLA BONA FOR IMPLANTS
Dalla Bona, Implant Female Kit: includes Female, Spacer & Brass Analog
Dalla Bona, Resilient Female, Gold
FH=3.1mm
Dalla Bona, Resilient Female, Titanium
FH=3.4mm
Dalla Bona, Resilient Female, Plastic (4)
FH=3.5mm
Dalla Bona Hex Analog, Brass (2)
Dalla Bona Hex Spacer, Brass (2)
PVC Ring (6), replacement ring for Dalla Bona female
40-430002
97-430282
99-451012
99-430282
40-430017
40-430016
97-430200
ORS FOR IMPLANTS
ORS, Retainer Rings (6)
H=2.0mm ø=5.1mm
ORS, Combo O-Rings: 6 blue, 6 red (processing), 6 wt, 6 blk
Outside ø=4.5mm Inside ø=1.4mm
ORS, Implant Female Kit: includes Retainer Ring, Brass Analog and 3 red processing & 3 white final O-Rings
O-Ring Hex Analog, Brass (2)
99-440044
99-443037
40-440002
40-440017
63-008519
Male Retention
Sequence
Least to Most:
Blue - Pink - Clear
Includes 1 metal housing with a black nylon processing male, spacer,
3 final nylon males: 1 clear 5lbs, 1 pink 3lbs & 1 blue 1.5lbs retention
63-008540
Locator Male Extended Range Complete
Locator Replacement Males Inserts, retention 5 lbs, clear (4)
Locator Replacement Males Inserts, retention 3 lbs, pink (4)
Locator Replacement Males Inserts, retention 1.5 lbs, blue (4)
Locator Extended Range Replacement Male, 3 lbs retention, green (4)
Locator Extended Range Replacement Male, 2 lbs retention, orange (4)
Locator Extended Range Replacement Male, 1.5 lbs retention, red (4)
Locator Impression Male
Locator Female Analog Standard 4mm
Locator Female Analog Wide Platform 5-6mm
63-008524
63-008527
63-008529
63-008547
63-008915
63-008548
63-008505
63-008530
63-008516
Replacement Males
Includes 1 metal housing with a black nylon processing male, spacer,
green nylon ex range male 3 lbs retention, orange nylon
ex range male 2 lbs retention and red ex range male 1.5 lbs retention
5 lbs.
3 lbs.
1.5 lbs.
Extended Male
Retention Sequence
Least to Most:
Red - Orange - Green
Extended Range Males
LOCATOR FOR IMPLANTS
Locator Male Complete
3 lbs.
2 lbs.
1.5 lbs.
TOOLS
BIO-TORQ Wrenches, Socket & Driver
59-100010
59-100020
59-100030
59-100035
BIO-TORQ Socket
BIO-TORQ Extension
BIO-TORQ ORS / Dalla Bona Tip/Driver
BIO-TORQ Locator Tip/Driver
59-100146 short
59-100190
59-100195
59-100140
59-100147 long
LT/RA DRIVER
LT/RA RA Hand Driver
LT/RA RA Handle / Socket
LT / RA ORS / Dalla Bona Tip
LT/RA Locator Tip/Driver
Dalla Bona Activating Tool, Blue
Dalla Bona Deactivating Tool, Yellow
Locator Core Insertion / Removal Tool
Locator Male Removal Tool only
Locator Parallel Posts (4)
58-100146 short
58-100000
58-100190
58-100140
58-100147 long
99-451017
99-451018
63-008393
63-008397
63-008517
Allegro OD/DE Micro/Regular Insertion Tool
73-410162
Locator Core Insertion / Removal Tool
Dalla Bona Activating Tool
Out Position
Female
Triangular
Seating Tool
Male
Removal Tool
Dalla Bona Deactivating Tool
In Position
Male Seating Tool
Interior .050" hex for insertion
257
To Order: 800-999-3003 • 650-340-0393
IMZ
ALLEGRO (for replacement parts see Allegro OD section page 99)
IMZ Non-Hex 3.3 & 4.0
Overdenture Bar
Restorations
Compatible
IDEAL BAR RESTORATIONS
There are numerous options for implant bar restorations available today. To
simplify your search, we have selected the most proven and popular systems on this page. For a complete listing of all bar system components,
refer to the Bar and Clip Quick Reference Charts.
Most implant bar restorations involve from 2 to 5 implants. The ideal implant
bar system incorporates a bar and retentive clips in the anterior section and
locking pin attachments distally for support and stability.
The Hader-EDS Bar Master kit is the preferred choice. The CM Gold Clips
may be used as an alternative. The locking SwissLoc NG Attachment is the
preferred distal attachment to prevent lift-off and still provide resiliency. The
Lew Attachment is a viable alternative.
For Laser Welding Technique, use only titanium bars and posts.
Recommended parts needed for a successful bar restoration:
PPM Bar
0 degree
Hader-EDS
Housing
Hader-EDS
Clips
SwissLoc
Attachments
Hader-EDS
Bar
Description
Order #
HADER-EDS BAR MASTER KIT
Master Kit includes 6 yellow plastic clips, 6 metal housings, 2 seating tools and 2 short plastic bars (50mm)
TOOLS:
Hader-EDS Bar Analog 50mm, aluminum (1)
Hader-EDS Fabricating Rider / Clip (6) Green
Hader-EDS Impression Clip (6) Blue
99-531005
CM HADER-EDS BAR KIT
CM Kit includes 6 CM gold riders (clips) with spacers and 2 short plastic Hader-EDS bars (50mm)
TOOLS:
CM Adjusting Tool (can be used with all metal riders / sleeves)
CM Bar Analog 50mm (aka Hader-EDS Bar Analog), aluminum
PARTS
Hader-EDS Combo Clips (18) 6 white, 6 yellow, 6 red and 1 seating instrument
Hader-EDS Bar, short plastic (6) Green
Hader-EDS Metal Housings (6) Gold
99-531015
99-531020
99-531080
99-532000
97-510125
99-531015
99-531009
99-531030
99-531060
SWISSLOC NG ATTACHMENT
SwissLoc NG 4.0 mm
*L=4.5mm Housingø=3.4mm Plungerø=1.5mm
X
89-600040
SwissLoc NG 6.0 mm
X
89-600060
SwissLoc NG 7.5 mm
X
89-600075
*Note: SwissLoc NG 7.5 can be reduced to 4mm. Length is measured in closed position from head of plunger to end of housing.
TOOLS:
SwissLoc NG Screwdriver
89-600010
SwissLoc NG Processing Jigs (2)
89-600015
SwissLoc NG 1.5mm Drill (1)
74-600615
PPM PLASTIC BAR PATTERNS (50mm)
PPM Bar 0 degree (3 short 3.7mm, 3 tall 8.0mm), blue
PPM Bar 2 degree (3 short 3.7mm, 3 tall 8.0mm), red
PPM Bar 4 degree (3 short 3.7mm, 3 tall 8.0mm), yellow
TOOLS:
PPM Bar Mandrel 0 degree (for plastic or titanium bar)
PPM Bar Mandrel 2 degree (for plastic or titanium bar)
PPM Bar Mandrel 4 degree
99-560000
99-562000
99-564000
99-560001
99-562001
99-564001
IMZ REPLACEMENT BAR CLIP WITH SCREWS & BACKPLATE
IMZ White Bar Clip & Screw (2) Assembly and Backplate
57-8510
Fits original 2mm diameter IMZ bar. Used for overdenture bar restorations. Includes: 1 white clip, 2 screws
and 1 backplate.
PARTS
IMZ White Bar Clip only
IMZ Screw only
IMZ Backplate only
57-8511
57-8512
57-8513
256
To Order: 800-999-3003 • 650-340-0393
Insertion Drivers
Tools
INSERTION DRIVERS
hand held socket or the BIO-TORQ wrenches. The LT / RA
(latch type) tips are used with right angle handpiece type
drivers.
LT / RA
BIO-TORQ
The BIO-TORQ (B-T) and LT / RA Systems were designed to
facilitate the insertion of implant components. The BIOTORQ insertion tips may be utilized with the BIO-TORQ
A
Socket
B
Extension
C
Slot
D
Hex
F
G
H
J
IMC 3.3 IMC 4.0 UMA sht UMA long
Description
Hand Held Socket / Handle (A)
BIO-TORQ Extension (B)
Slot Tip Short
Slot Tip Long (C)
.050" Hex Tip Short
.050" Hex Tip Long (D)
.048" Hex Tip Short
.048" Hex Tip Long
Dalla Bona / ORS Hex Tip
Locator Tip, short
Locator Tip, long
Complete Abutment LT / RA Tip (E)
BIO-TORQ Tip IMZ / IMC 3.3, Short (F)
BIO-TORQ Tip IMZ / IMC 4.0, Short (G)
UMA Tip Short (H)
UMA Tip Long (J)
.9mm CS Hex Tip Short
A
Handle
C
Slot
D
Hex
E
Complete
H
UMA
Order #
Order #
Bio-Torq
LT/ RA Driver
59-100190
59-100195
59-100110
59-100115
59-100120
59-100125
59-100130
59-100135
59-100140
59-100146
59-100147
N/A
59-100171
59-100172
59-100150
59-100155
59-100200
58-100190
N/A
58-100110
58-100115
58-100120
58-100125
58-100130
58-100135
58-100140
58-100146
58-100147
58-100170
N/A
N/A
58-100150
N/A
N/A
STANDARD DRIVERS, B-T WRENCHES & LT / RA DRIVER
Note: For Slot Screws do not exceed
10 N/cm of torque.
A
B
C
D
Description
Order #
Standard Drivers and FG Drivers
11-000007
11-000005
11-000006
11-000004
BIO-TORQ Wrenches & LT / RA Driver
LT / RA Driver
59-100010
59-100020
59-100030
59-100035
58-100000
259
To Order: 800-999-3003
•
650-340-0393
IMZ
DDS .050" Hex Driver (A)
DDS Slot Screwdriver (B)
Lab .050" Driver (C)
Friction Grip Driver (D)
IMZ Non-Hex 3.3 & 4.0
Compatible
Reamers
Lapping Tools
REAMERS
The carbide reamers are used to refine the internal access hole of a castable cylinder. They also
refine the seat for the head of the screw. Each
carbide reamer and Pin Vise are sold separately.
The Pin Vise will fit all carbide reamers. The
Reamer fits all UMA and IMZ IME European new
style cylinders.
Reamer
Pin Vise
Description
A
Order #
Reamer, UMA Abutment Carbide .0880" (also fits IMZ & Paragon UCLA Cylinders) (requires Pin Vise 40-000150)
11-000150
40-000150
LAPPING TOOLS
The Lapping tools are used with diamond polishing paste to refine the fitting surface of the cast
cylinder. We recommend that you use it not more
than 5-6 times. For superior restorations, you
may want to use the 1 micron white diamond
lapping paste. The lapping tool fits the cylinders
for the Complete Abutment, IME and UMA.
B
Description
Order #
11-000155
258
To Order: 800-999-3003 • 650-340-0393
Screws for
Original IMZ Parts
SCREWS FOR ORIGINAL IMZ COMPONENTS
3.3
4.0
3.3
4.0
3.3
4.0
3.3
4.0
3.3
Hex
Hex
A
IMC Conversion
Screw
B
IMC Coping Screw
C
IME Coping Screw
4.0
D
IMC Fastening
for Plastic Cylinder
3.3
4.0
3.3 & 4.0
3.3 & 4.0
Hex
E
IMC Fastening
for Gold Cylinder
F
G
H
IME Fastening Screw Securing Screw Hex Head
for Gold Cylinders
Bar Clip to
3.3 & 4.0
Back Plate Implant Screw
ALL SCREWS HAVE .050" HEX except Back Plate Screw (slot)
Description
Order #
Order #
3.3mm
4.0mm
IMC Conversion Screw, .050" Hex (A)
57-8198CA
Used when converting from IME to IMC Abutment. Threads must be shortened to appropriate length.
3.3mm—ONLY fits 3.3 IMC Abutment 4.0mm—Fits both 4.0 IMC & 4.0 IME Abutments. 2.2mm ø head.
57-8197C
IMC Coping Screw, .050" Hex (B)
Used for overdenture bars. Screw has 2.8mm diameter head.
57-8158C
57-8157C
IME Coping Screw, .050" Hex (C)
Used for overdenture bars. Screw has 2.8mm diameter head.
57-8534
57-8535
IMC Fastening Screw for Plastic Cylinder, .050" Hex (D)
Screw has 2.4mm diameter head.
57-8146C
57-8144C
IMC Fastening Screw for Gold Cylinder, .050" Hex (E)
Screw has 2.2mm diameter head.
57-8196C
57-8199C
IME Fastening Screw for Gold Cylinder, .050" Hex (F)
57-8905A
Hex is in base of screw head allowing screw head to be shortened if necessary. 2.2mm ø head.
57-8906A
IMZ Screw to Secure Bar Clip to Back Plate 3.3 & 4.0, slot (G)
For securing plastic clip to the Back Plate ONLY.
57-8510
57-8510
IMZ Screw for 3.3 & 4.0 Hex Head Implant, .050" Hex (H)
For IMZ Hex Head 3.3 & 4.0 Implant ONLY.
57-440052
57-440052
Note: For detailed dimensions of IMZ screws see IMZ Reference Charts immediately following this page.
All screws have .050" hex.
IME
Abutment
Note the difference in placement of
screw threads in the abutments.
IME threads are located at the top,
IMC threads are located at the
bottom.
IMC
Abutment
Inner thread
is located in
TOP portion of
abutment
IMZ
Inner thread
is located in
BOTTOM
portion of
abutment
261
To Order: 800-999-3003 • 650-340-0393

IMZ Implant System - Swiss NF Metals Inc

Transcription

Similar documents

Penny-Power-7-IMPLANT-SEM

Silimed cover 6page

drill sequence

Instruction Manual

Splash and Discover Ad Placements

Hand Tools Guide - TETRIX Robotics

① Entry Record Data Locator

IMC Online Directions - Carbon Lehigh Intermediate Unit 21

Valtronic Technologies (Suisse) AG - Sohaila Setayesh

MAX - Southern Implants