R-55E Owner`s Manual

Transcription

R-55e Audio Console
TECHNICAL MANUAL
July 2004
R-55e Audio Console Technical Manual - 1st Edition
©2004 Audioarts® Engineering*
AUDIOARTS ENGINEERING
600 Industrial Drive
New Bern, North Carolina 28562
252-638-7000
*a division of Wheatstone Corporation
/ July 2004
R-16 / DecR-55e
1997
Attention!
ATTENTION
Federal Communications Commission (FCC) Compliance
Notice:
Radio F
requency Notice
Frequency
NOTE: This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own
expense.
!
This is a Class A product. In a domestic environment, this
product may cause radio interference, in which case, the
user may be required to take appropriate measures.
This equipment must be installed and wired properly in order to assure
compliance with FCC regulations.
Caution! Any modifications not expressly approved in writing by
Audioarts could void the user's authority to operate this equipment.
R-55e / March 2006
R E A D ME !
CONTENTS
R-55e Technical Manual
Table of Contents
Chapter 1 – Installation
Unpacking the Console ............................................................. 1-2
Countertop Mounting ................................................................. 1-2
System Ground .......................................................................... 1-3
Power Supply ............................................................................. 1-5
Failsafe Dual Redundant Supply ............................................................................ 1-6
Energizing ............................................................................................................... 1-6
Audio and Control Wiring .......................................................... 1-7
Connection Procedures .......................................................................................... 1-7
Unbalanced Connections (analog audio) ............................................................... 1-7
Modules Layout .......................................................................... 1-7
Hand Crimp Tool Wiring Instructions ...................................... 1-8
Wiring Procedure - Double Connection to One Pin .............. 1-10
R-55e 12-Position Frame - Modules Layout ........................... 1-11
Chapter 2 - Quad Mic Preamp (QMP-4)
Overview ..................................................................................... 2-2
Internal Programming Options ................................................. 2-3
Phantom Power ...................................................................................................... 2-3
Hook-ups ..................................................................................... 2-3
AUDIO INPUT CONNECTIONS ............................................................................. 2-3
AUDIO OUTPUT CONNECTIONS ......................................................................... 2-4
POWER CONNECTIONS ....................................................................................... 2-5
Plug Terminal Pinout Drawing .................................................. 2-6
Installing the Optional Second QMP-4 Mic Preamp ................ 2-7
R-55e / July
Nov 2004
2005
page Contents – 1
CONTENTS
Chapter 3 - Stereo Line Input (SL-55e)
Module Overview ........................................................................... 3-2
Internal Programming Options ....................................................3-3
Mutes ........................................................................................................................ 3-3
Timer Restart ............................................................................................................ 3-3
Local/Ready .............................................................................................................. 3-3
Talkback .................................................................................................................... 3-3
Hook-ups ........................................................................................3-4
ANALOG AUDIO CONNECTIONS ........................................................................... 3-4
CONTROL CONNECTIONS ..................................................................................... 3-4
Remote ON & OFF ................................................................................................... 3-5
Cough ....................................................................................................................... 3-5
External START & STOP ......................................................................................... 3-5
Ready ........................................................................................................................ 3-5
Talkback to Control Room ........................................................................................ 3-5
On Tally ..................................................................................................................... 3-6
Tally B ....................................................................................................................... 3-6
DB Connector Pinout Drawing ..................................................... 3-7
Chapter 4 - Output Module (OM-55e)
Module Overview ........................................................................... 4-2
Hook-ups ........................................................................................4-3
DB-25 Connector — AUDIO ..................................................................................... 4-3
DB-9 Connector — AUDIO ....................................................................................... 4-3
DB-9 Connector — CONTROL ................................................................................. 4-4
Chapter 5 - Control Room/Studio Module (CRS-55e)
Module Overview ........................................................................... 5-2
Cue Interrupt ............................................................................................................. 5-3
CR/Cue Mute ............................................................................................................ 5-3
Studio Mute ............................................................................................................... 5-3
Studio Dim ................................................................................................................ 5-3
Hook-ups ........................................................................................5-4
Left DB-25 “A” Connector — AUDIO ........................................................................ 5-4
Right DB-25 “B” Connector — AUDIO ..................................................................... 5-4
R-55e / July 2004
page Contents – 2
CONTENTS
Chapter 6 - Second Studio Module (SS-55e) - optional
Module Overview ........................................................................... 6-2
Cue Interrupt ............................................................................................................. 6-3
HDPN 3 Mute ............................................................................................................ 6-3
Studio 2 Mute ............................................................................................................ 6-3
Studio 2 Dim ............................................................................................................. 6-3
Hook-ups ........................................................................................6-4
Left DB-25 “A” Connector — AUDIO ........................................................................ 6-4
Right DB-25 “B” Connector — AUDIO ..................................................................... 6-4
Chapter 7 - Superphone Module (SPN-55e) - optional
Module Overview ........................................................................... 7-2
Caller Set-Ups .......................................................................................................... 7-2
Mutes ........................................................................................................................ 7-3
Timer Restart ............................................................................................................ 7-3
Gain Trimpot ............................................................................................................. 7-3
Hook-ups ........................................................................................7-3
AUDIO CONNECTIONS ........................................................................................... 7-3
CONTROL CONNECTIONS ..................................................................................... 7-3
Remote ON & OFF ................................................................................................... 7-4
External START & STOP ......................................................................................... 7-4
On Tally ..................................................................................................................... 7-4
Chapter 8 - Line Select (LS-55e) - optional
Module Overview ........................................................................... 8-2
Hook-ups ........................................................................................8-3
Left DB-25 “A” Connector — AUDIO INPUTS .......................................................... 8-3
Left DB-25 “A” Connector — AUDIO OUTPUTS ..................................................... 8-3
Right DB-25 “B” Connector — AUDIO INPUTS ....................................................... 8-3
Chapter 9 - Tape Remote Module (TR-55e) - optional
Module Overview ........................................................................... 9-2
DB Connector Pinout Drawings
START/STOP Function Control I/O .......................................................................... 9-3
Full-Function Control I/O .......................................................................................... 9-4
R-55e / July 2004
page Contents – 3
CONTENTS
Chapter 10 - Meterbridge
Overview ................................................................................... 10-2
Digital Timer ............................................................................. 10-2
Digital Clock ............................................................................. 10-3
Controls ................................................................................................................. 10-3
Setting the Time .................................................................................................... 10-3
Capacitor Backup ................................................................................................. 10-3
Operational Modes ............................................................................................... 10-3
Chapter 11 - Parts List
QMP-4 Quad Mic Preamp .................................................................................... 11-2
SL-55e Stereo Line Input ...................................................................................... 11-3
OM-55e Master Output ......................................................................................... 11-5
CRS-55e Control Room/Studio ............................................................................ 11-7
SS-55e Second Studio (optional) ....................................................................... 11-10
SPN-55e Superphone Input (optional) ............................................................... 11-13
LS-55e Line Select ............................................................................................. 11-15
TR-55e/FF Tape Remote (optional) ................................................................... 11-16
TR-55e/SS Tape Remote (optional) ................................................................... 11-17
MBE-5508 Mother Board .................................................................................... 11-18
MBR-2000 Mother Board .................................................................................... 11-19
MBR-5510 Mother Board .................................................................................... 11-20
CLK-55e (Clock/Timer for 26-pos. Frame) ......................................................... 11-22
TMR-55e (for 18-pos. Frame) ............................................................................. 11-24
SPS-100 Power Supply ...................................................................................... 11-26
LED-3 Meter LED Lamp ..................................................................................... 11-28
R-55e-18 (26-pos.) Frame .................................................................................. 11-39
R-55e-12 (18-pos.) Frame .................................................................................. 11-31
R-55e-8 (12-pos.) Frame .................................................................................... 11-33
R-55e-18 Connector Kit ...................................................................................... 11-34
R-55e-12 Connector Kit ...................................................................................... 11-35
R-55e-8 Connector Kit ........................................................................................ 11-36
R-55e Console .................................................................................................... 11-37
R-55e Spare Parts Kit ......................................................................................... 11-38
Chapter 12 - Schematics and Load Sheets
Console Flow Diagram ............................................................ 12-2
Quad Mic Preamp (QMP-4)
schematic .............................................................................................................. 12-3
load sheet drawing ................................................................................................ 12-4
Stereo Line Input (SL-55e)
schematic .............................................................................................................. 12-5
load sheet drawing ................................................................................................ 12-8
R-55e / July
Nov 2004
2007
page Contents – 4
CONTENTS
Output Master (OM-55e)
schematic .............................................................................................................. 12-9
load sheet drawing .............................................................................................. 12-12
Control Room/Studio (CRS-55e) & Second Studio (SS-55e)
schematic ............................................................................................................ 12-13
Superphone (SPN-55e)
schematic ............................................................................................................ 12-17
Line Select (LS-55e)
schematic ............................................................................................................ 12-21
Tape Remote (TR-55e)
schematic ............................................................................................................ 12-23
Clock/Timer (CLK-55)
schematic ............................................................................................................ 12-25
Mother Board—Extender (MBE-55)
schematic ............................................................................................................ 12-28
Mother Board—Right (MBR-2000)
schematic ............................................................................................................ 12-30
schematic ............................................................................................................ 12-32
Meter LED Lamp (LED-3)
schematic ............................................................................................................ 12-35
Power Supply (SPS-100)
schematic ............................................................................................................ 12-37
R-55e / July
Nov 2004
2007
page Contents – 5
INSTALLATION and POWER
Installation and Power
Chapter Contents
Unpacking the Console ............................................................. 1-2
Countertop Mounting ................................................................. 1-2
System Ground .......................................................................... 1-3
Power Supply ............................................................................. 1-5
Failsafe Dual Redundant Supply ............................................................................ 1-6
Energizing ............................................................................................................... 1-6
Audio and Control Wiring .......................................................... 1-7
Connection Procedures .......................................................................................... 1-7
Unbalanced Connections (analog audio) ............................................................... 1-7
Modules Layout .......................................................................... 1-7
Hand Crimp Tool Wiring Instructions ...................................... 1-8
Wiring Procedure - Double Connection to One Pin .............. 1-10
R-55e - 12-Position Frame - Modules Layout ........................ 1-11
R-55e / Nov
July 2004
2005
page 1 – 1
Installation and Power
Unpacking the Console
The R-55e console is shipped as two packages. One (larger) carton
contains the console and technical documentation; and the other (smaller)
contains the rackmount power supply, connecting cable, and connector
kit.
Countertop Mounting
The R-55e audio console is designed for countertop mounting. Console placement should avoid proximity to any electromagnetic fields,
such as large power transformers, motors, and fluorescent lighting
fixtures. If you will be securing the console to the counter top, you may
want to pre-drill the mounting holes (see sketch below).
Set the console in place on the counter, and remove the screws that
hold down the first and the last modules in place (two per module).
Carefully remove those modules from the frame. Attach the console
mainframe to the counter top, using the holes provided in the bottom of
the chassis and screws appropriate to the counter material, and reinstall
the removed modules.
The console extends approximately 7 5/8” above the countertop at the
meterbridge. The hinged meterbridge will require 14” above the countertop
surface and 4 3/4” behind the rear meterbridge to open freely.
Do not connect the R-55e console to its power supply (and do not
connect the power supply to the AC power line) until instructed to do
so.
NOTE: This console contains static-sensitive devices. Normal precautions against static discharge should be observed when handling
individual modules.
7.6341
7.369
(WITHOUT FEET)
2.356
.750
24.180
NOTE: Dimensions shown are for 26-position
frames; 18-position frames dimensions shown in [];
12-position frames dimensions shown in ().
17.750
20.044
D = .171"; USE #8 SCREWS
.760
37.750 [25.670] (16.610)
39.270 [27.190] (18.130)
40.770 [28.690] (19.630)
R-55e / July 2004
page 1 – 2
System Ground
The first step is to ground the console.
Note that as supplied from the factory, console rackmount power
supply common, audio ground, and the R-55e mainframe are connected together at the console, but are NOT connected to electrical
ground and the chassis of the power supply. Safety requirements
dictate that a positive connection from the console mainframe to
electrical ground be made in the completed installation. Use the
grounding lug on the rear of the mainframe to establish your system
ground. The grounding lug may be found at the rear of the console, on
the rear frame panel, to the left if you are looking at the rear of the
console.
The system ground serves two important purposes:
(1) It provides a zero signal reference point for the entire audio system;
(2) It assures safety from electrical shock.
There exist two terms that one encounters in a discussion of ground:
(A) EARTH GROUND, which is usually a heavy copper rod driven into the
soil adjacent to the building (around 6 feet down) or a connection to the copper
water pipes leading into the building. Either is acceptable (unless, of course,
the water pipe is made of plastic).
MIC PANEL
EFFECTS RACK
CONSOLE
GND
DEVICE 1
DEVICE 2
2-TRACK
etc.
DEVICE N
MULTI-TRACK
AC BREAKER
BOX
HEAVY
(#4 or #6)
COPPER
WIRE
POWER COMPANY
EARTH GROUND
HIGH POWER
EQUIPMENT RACK
Tie the console ground lug
terminal strip to the system
earth ground. Tie every piece
of equipment in the entire
audio system to the console
ground lug terminal strip.
CONSOLE POWER SUPPLY
CONTROL ROOM POWER AMP
COPPER ROD
STUDIO POWER AMP
OTHER
3–5 ft.
SOIL
3-wire ground or separate wire run from chassis
TYPICAL SYSTEM
GROUNDING SCHEME
R-55e / July 2004
page 1 – 3
(B) THE POWER COMPANY EARTH CONDUCTOR that enters the building at the power line breaker box; this conductor should be (and is often by code)
tied to the above-mentioned earth ground at one point. This point is the SYSTEM
EARTH GROUND.
TIE THE CONSOLE GROUND LUG TO THE SYSTEM EARTH
GROUND. TIE EVERY PIECE OF EQUIPMENT IN THE ENTIRE
AUDIO SYSTEM TO THE CONSOLE GROUND LUG. If the system
earth ground point is inaccessible, tie the console ground lug to the power
company earth conductor at the main breaker box (see drawing "Typical
Grounding Scheme" on previous page).
Each piece of equipment should be connected by its own ground wire
(usually the round third pin on the AC cord). This means that every AC
outlet must have a separate conductor run to the console ground lug; the
outlets cannot be daisy-chained as is normally encountered in commercial
and residential AC systems. Any equipment not supplied with 3-wire AC
cables must have individual ground wires (16 gauge or larger) connected
to their chassis grounds and then run to the console ground lug terminal
strip.
Further Grounding Details
Check all equipment to be absolutely certain that each unit is power
transformer isolated from the AC mains to prevent safety hazards.
It is assumed that in each piece of audio equipment the audio ground
and the chassis are tied together at some point. Any piece of equipment
lacking a grounded chassis is likely to be prone to interference problems.
Locate all unbalanced audio equipment in the same rack if possible, to
minimize chassis ground potential differences. It may also be helpful to
insulate each piece of unbalanced equipment from its mounting rails in the
rack by means of nylon 10-32 screws and insulating washers between rails
and faceplates.
Once the system is properly grounded, proceed with the console
power supply installation and connection (next section).
R-55e / July 2004
page 1 – 4
INSTALLATION AND POWER
Power Supply
Front view of the SPS-100
rackmount power supply
Rear view of the SPS-100
rackmount power supply
The R-55e console is powered by an Audioarts Model SPS-100 If failsafe redundant supplies have been ordered,
rackmount power supply. This unit occupies two 19” wide rack spaces you will be installing two
(total height 3-1/2”). Convection cooled, it requires ample ventilation units and an additional
rackmount panel.
space above and below it.
Note that the power supply should be mounted in an equipment rack
within fifteen feet of the console (but no closer than 3 feet). Avoid locating any high gain equipment (such as phono preamps, tape recorders,
etc.) too near the rackmount supplies, to avoid magnetic interference
into that equipment.
Once the supply is rackmounted, it should be connected to the console using the factory supplied cable.
The cable has two different types of
connectors on it: an 8-pin female connector that connects to the console’s
power supply connector, and an 8-pin
male connector that plugs into the
rear of the rackmount SPS-100 power
supply. The console’s power supply
connector is located at the rear of the
Console Power Supply
console, at the right end of the meterEnd
End
bridge bottom pan. If you are using
PS Cable Pinout
one supply, connect it to the console
P
I
N
PIN
connector. If you are using two supPhantom
VIO
1
1 VIO
plies (failsafe option), connect the long
Digital Common
power supply cable to the center conGRN 2
2 GRN
Digital Common
nector of the rackmount failsafe panel.
3
3 BRN
BRN
Power Supply End
+ Digital
Then connect one supply with a short Console End WHT 4
4 WHT
8-pin Connector
8-pin Connector
+ Digital
cable to either of the two remaining
Female
Male
ORG 5
5 ORG
Audio Common
connectors on the failsafe panel and
BLK
6 BLK
6
-V
connect the second supply with a short
7 BLU
BLU 7
cable to the last connector.
+V
RED 8
8 RED
R-55e / Dec
July 2012
2004
page 1 – 5
Note that each power supply is fitted with a 3-wire grounded AC
cord that should be plugged into a "clean" AC power source, that is, an
AC source that feeds only the control room audio gear. This source
should be a separate feed from those powering lighting, air-conditioning, or any other non-audio machinery. The third pin ground wire of the
AC source should be tied to the central system ground point.
The power feed recommended in the text is often installed and referred
to in studios as an “isolated AC ground” outlet.
It is usually orange in
color.
Failsafe Dual Redundant Supply
Wheatstone failsafe power supply systems use two separate rackmount power supplies for each piece of powered equipment. Though
either is capable of running a full load on its own, in failsafe operation
both units run in tandem: if one fails, the other takes over, assuring
uninterrupted operation.
In order for failsafe systems to perform as designed, always have
BOTH rackmount supplies powered up and connected to their associated equipment.
Energizing
Assuming the R-55e console mainframe is properly placed and
grounded, and its SPS-100 power supply correctly rackmounted and
connected to the console, you may now energize the power supply by
plugging it into the AC mains. The console's VU meters will illuminate
and individual module switches will assume factory default settings.
Note: To de-energize the console, unplug the rackmount power
supply’s AC cord from the AC mains. Never de-energize the console
by disconnecting the cable that connects the console and power
supply together.
Once you have verified proper power-up, unplug the rackmount power
supply to de-energize the console. You may now proceed to wire up
audio and control connections.
R-55e / July
Apr 2008
2004
page 1 – 6
Audio and Control Wiring
All audio and control I/O connections to the R-55e console are made
through multipin DB-25 connectors located on the top of each module. The
output module also has a DB-9 connector. The factory supplied hand
crimping tool is used for all I/O wiring connections to and from the console
(see instruction on page 1-8).
Connection Procedures
As supplied from the factory, the console requires no logic connections
to function. Therefore an orderly installation begins with the audio wiring.
Note this manual is organized by module type (inputs, outputs, monitor
modules, etc.); each chapter contains detailed wiring instructions for its
module type. Proceed through the manual, chapter by chapter, until all
modules have been wired to suit your particular installation requirements.
Once proper audio operation is verified, go back to each individual chapter
and proceed with control wiring.
Unbalanced Connections (analog audio)
ANALOG INPUTS — Wire to the console with typical shielded two
conductor cable (like Belden 9451), just as if you were connecting a balanced
source. At the unbalanced source machine’s output, connect the black wire
(LOW) to the shield. If the machine has a -10 dBu output, don’t hesitate to
turn module input gain as high as is needed.
ANALOG OUTPUTS — R-55e consoles use an electronically balanced
output circuit. Care must be exercised when connecting them to an unbalanced system. While temporarily shorting the low side of the output signal
to ground will not cause any problems, continued operation will result in
increased distortion, decreased reliability, and possible oscillation problems. If you must connect the output to an unbalanced system, be sure to
leave the low side unterminated, and connect the unbalanced system to the
high side output and shield connections.
Modules Layout
The R-55e console’s mainframe comes supplied with up to 20 (for 26 pos.
frame), 12 (for 18 pos. frame), or 8 (for 12 pos. frame) line level input
modules along with an output module, and a control room/studio module.
Each module type has its assigned slot (see drawings on pages 1-11, 11-12,
and 1-13). To handle mic level inputs, a quad mic preamp is included. Also
there can be optional modules: a superphone, a line select, a second studio,
and a tape remote module. Optional modules (except second studio) can be
placed in any input slot. The optional second studio module has a dedicated
slot (see layout drawings).
R-55e / Nov
July 2004
2005
page 1 – 7
HAND CRIMP TOOL WIRING INSTRUCTIONS
The supplied hand crimping tool (W/S#850067) is used for all I/O wiring connections to and from the console. It is to be used with the supplied pin (figure 1)
intended for 22"-28" gauge wire.
INSULATION
TABS
CONDUCTOR
TABS
INSULATION
STOPS HERE
(2) The terminal conductor tabs (pointing UP) are
placed in anvil 18-22; the terminal's insulation tabs
extend in front towards the camera.
(3) The stripped wire is placed into the terminal and
crimped. Note the wire's insulation must stop just
short of the conductor tabs (detail)
(1) Pin crimp terminal
1) Strip wire approximately 3/16" (insert in
proper wire stripper, rotate one half turn, and
pull insulation off wire).
2) Leaving wire aside for the moment, with
crimping tool fully open (engraved side toward
you) bring a terminal into position from the
unmarked side of the tool. Place the conductor
tabs (inner set as shown in figure 1) on the
"18-22" or "24-30" (depending on the wire) anvil (slightly curved surface) so that the circular
portion of the tabs rests in the curved surface
of the anvil and the two tabs face up into the
walls of the female jaw. The insulation tabs will
be flush with the top of the tool (figure 2).
3) Close tool very slightly, only to the point
of holding the terminal in position (figure 2).
4) Insert wire into terminal until wire insulation is stopped by conductor tabs (figure 3).
CRIMP by squeezing handles until jaws are fully
closed (figure 4).
5) If there is an insertion error or if a circuit
change is needed, you'll need to use an extractor tool to remove terminals (see next page).
Note that metallized plastic hoods for each
connector are also supplied with the console.
(4) Final step: jaws fully closed; the insulation tabs
have been crimped.
R-55e / July 2004
page 1 – 8
EXTRACTOR PIN INSTRUCTIONS
(5) Place extractor tip over pin terminal to be
removed.
R-55e / July 2004
If you accidentally insert a crimp terminal
pin into the wrong socket, you'll need to use
the supplied pin extractor tool (W/S#850069)
to remove terminal pin, and correct your mistake without having to sacrifice a connector.
Place extractor tip (red side) over terminal pin
to be removed (figure 5), and press it downwards motion until tip rests upon Housing.
Then pull out the terminal pin from Housing.
It should never be necessary to discard a connector due to a wiring error.
page 1 – 9
Wiring Procedure - Double Connection to One Pin
ref: DB-25 male multi-pin connector
Most audio equipment machine interfaces (as well as Wheatstone consoles) use
subminiature D-type connectors. Sometimes the interfaces require making two connections to a single DB pin. If the wiring has been set up using punchblocks, this is not a
problem; however, for situations where direct machine-to-console wiring is used, Wheatstone recommends the following procedure:
1) Connect the first wire to the desired pin as you normally would.
2) Note connector pins may easily be removed from the DB-25 shell with the wire still
attached: Hold the connector with the metal part down and observe its side. You
will see a row of "Vees"—simply press the top of the selected vee together with a
scribe or other sharp instrument; this will unlock the pin from the shell, allowing
it to be removed.
3) With the pin removed, strip out a short section of insulation from the connected
wire and wrap and solder the second wire to the first as shown above.
4) A short piece of heatshrink tubing (pictured here before being slid into place)
completes the connection.
5) Re-insert the pin into the DB-25 shell, spreading the vee apart to lock it in place.
R-55e / July 2004
page 1 – 10
NOTE: 1. CONSOLE CAN ACCOMMODATE UP TO 9 INPUT AND ACCESSORY MODULES (OPTIONAL MODULES—
SUPERPHONE, LINE SELECT, AND TAPE REMOTE—CAN BE PLACED IN ANY SLOT POS. 1-9).
2. MASTER OUTPUT, CONTROL ROOM, AND OPTIONAL SECOND STUDIO MODULES
HAVE THEIR DEDICATED SLOTS (AS SHOWN).
4. LAST SLOT AT THE RIGHT END OF THE FRAME COULD BE USED FOR OPTIONAL LINE SELECT AND
TAPE REMOTE MODULES.
R-55e / May 2005
R-55e-12-POSITION FRAME - MODULES LAYOUT
page 1 – 11
NOTE: 1. CONSOLE CAN ACCOMMODATE UP TO 13 INPUT MODULES AND ACCESSORY MODULES (OPTIONAL MODULES—SUPERPHONE, LINE SELECT, AND TAPE REMOTE—CAN BE
PLACED IN ANY SLOT POS. 1-13).
2. MASTER OUTPUT, CONTROL ROOM, AND OPTIONAL SECOND STUDIO MODULES HAVE THEIR DEDICATED SLOTS (AS SHOWN).
3. SECOND STUDIO SLOT COULD BE USED ALSO FOR OPTIONAL TAPE REMOTE OR LINE SELECT MODULE.
4. LAST TWO SLOTS AT THE RIGHT END OF THE FRAME SHOULD BE USED FOR OPTIONAL LINE SELECT AND TAPE REMOTE MODULES.
R-55e / May 2005
page 1 – 12
NOTE: 1. CONSOLE CAN ACCOMMODATE UP TO 21 INPUT AND ACCESSORY MODULES (OPTIONAL MODULES—SUPERPHONE, LINE SELECT, AND TAPE REMOTE—CAN BE PLACED IN ANY SLOT POS. 1-21).
2. MASTER OUTPUT, CONTROL ROOM, AND OPTIONAL SECOND STUDIO MODULES HAVE THEIR DEDICATED SLOTS (AS SHOWN).
3. SECOND STUDIO SLOT COULD BE USED ALSO FOR OPTIONAL TAPE REMOTE OR LINE SELECT MODULE.
4. LAST TWO SLOTS AT THE RIGHT END OF THE FRAME SHOULD BE USED FOR OPTIONAL LINE SELECT AND TAPE REMOTE MODULES.
R-55e / May 2005
page 1 – 13
QUAD MIC PREAMP
Quad Mic Preamp
(QMP-4)
Chapter Contents
Overview ..................................................................................... 2-2
Phantom Power ...................................................................................................... 2-3
Hook-ups ..................................................................................... 2-3
AUDIO INPUT CONNECTIONS ............................................................................. 2-3
AUDIO OUTPUT CONNECTIONS ......................................................................... 2-4
POWER CONNECTIONS ....................................................................................... 2-5
Plug Terminal Pinout Drawing .................................................. 2-6
Installing the Optional Second QMP-4 Mic Preamp ................ 2-7
R-55e / July 2004
page 2 – 1
QUAD MIC PREAMP
Quad Mic Preamp
(QMP-4)
Mic1
Mic2
Mic3
Mic4
Overview
The QMP-4 is a quad mono microphone preamplifier and is mounted
in the left side of the console meterbridge rear. Mic level sources are wired
to QMP-4 mic preamp inputs. QMP-4 output signals are then wired to
input pins of individual SL-55e input modules. Consoles are normally
supplied as though the outputs of the mic preamp will be wired to A inputs
of SL-55e modules 1-4.
Phantom power is available at each input port; it may be selectively
activated by a dipswitch SW1 (the factory default is OFF).
R-55e / July 2004
page 2 – 2
QUAD MIC PREAMP
Recessed meterbridge rear trimpots
(range 38dB) adjust the level of each input
independently.
Example: with a microphone input of
–60dBm @150Ω at the port, gain trim can set
levels from -22dBu to +16dBu (note maximum
preamp gain is +76dB).
Mic 1
Mic 2
Mic 3
Mic 4
All audio input and output signals are made via two 12-position plug
terminals mounted on the QMP-4 PCB.
Internal Programming Options
Internal programming for the quad mic preamp is made via printed
circuit board (PCB) mounted seven-position dipswitch SW1. Note that
when a dipswitch position is thrown to the right it is ON.
Phantom Power
Dipswitch SW1 turns phantom power on for the four microphone input
ports.
SW1 position 7 activates phantom power for microphone 1
As stated before, all user wiring to and from the QMP-4 takes place at
the 12-position plug terminals mounted on the QMP-4 PCB. A pinout
drawing on page 2-6 shows all wiring connections at a glance.
Audio Input Connections (CT3)
All signals are analog mono. The mic input level is normally -50dBu,
balanced.
Pin 1 – Mic
Pin 2 – Mic
Pin 3 – Mic
Pin 4 – Mic
Pin 5 – Mic
Pin 6 – Mic
R-55e
R-55e // July
Aug 2004
2006
1 In SH
1 In LO
1 In HI
2 In SH
2 In LO
2 In HI
1 2 3 4 5 6 7 8 9 10 11 12
Hook-Ups
Note the factory default
setting for phantom power
is OFF.
Typical 12-position
plug terminal
page 2 – 3
QUAD MIC PREAMP
Audio Output Connections (CT4)
All signals are analog mono. The mic output level is normally +4dBu,
balanced.
Pin 12 – Mic 1 Out SH
Pin 11 – Mic 1 Out LO
Pin 10 – Mic 1 Out HI
1 2 3 4 5 6 7 8 9 10 11 12
Pin 7 – Mic 3 In SH
Pin 8 – Mic 3 In LO
Pin 9 – Mic 3 In HI
Pin 10 – Mic 4 In SH
Pin 11 – Mic 4 In LO
Pin 12 – Mic 4 In HI
Typical 12-position
plug terminal
Note that each output wires in parallel to the left and right input
channels of an input stereo module (SL-55e).
For example:
Pin 25 - Line A Lt In SH
Pin 12 – Mic 1 Out SH wires to
Pin 11 - Line A Rt In SH
Pin 12 - Line A Lt In LO
Pin 11 – Mic 1 Out LO wires to
Pin 23 - Line A Rt In LO
Pin 24 - Line A Lt In HI
Pin 10 – Mic 1 Out HI wires to
Pin 10 - Line A Rt In HI
R-55e / July 2004
page 2 – 4
QUAD MIC PREAMP
Power Connections (CT7)
A ribbon cable connects the 10-pin connector on the QMP-4 (CT7) to the
10-pin connector mounted on the center of the MBR-2000 motherboard
(CT8) or MBR-55 motherboard (CT18) to provide power to the microphone
preamplifier.
Pin 1 – Analog Ground
Pin 3 - +Phantom V
Pin 4 – +Phantom V
Pin 5 – +V In
Pin 6 – +V In
Pin 7 – -V In
Pin 8 – -V In
R-55e / July 2004
page 2 – 5
QUAD MIC PREAMP
QMP-4 Quad Mic Preamp
Plug Terminal Pinouts
1
MIC 1 IN LO
2
MIC 1 IN HI
3
MIC 2 IN SH
4
MIC 2 IN LO
5
MIC 2 IN HI
6
MIC 3 IN SH
7
MIC 3 IN LO
8
MIC 3 IN HI
MIC 4 IN HI
9 10 11 12
MIC 4 OUT HI
1
MIC 4 OUT LO
2
MIC 4 OUT SH
3
MIC 3 OUT HI
4
MIC 3 OUT LO
5
MIC 3 OUT SH
6
MIC 2 OUT HI
7
MIC 2 OUT LO
8
MIC 2 OUT SH
9 10 11 12
INPUT
PORTS
ANALOG
MIC 1 IN SH
MIC 4 IN SH
MIC 4 IN LO
OUTPUT
PORTS
ANALOG
MIC 1 OUT HI
MIC 1 OUT LO
MIC 1 OUT SH
R-55e / July 2004
page 2 – 6
QUAD MIC PREAMP
Installing the Optional Second QMP-4 Mic Preamp
Optional
QMP-4 Area
Connector
The optional second QMP-4 comes complete with mounting hardware.
The ribbon cable, installed at the factory to provide power to the pre-installed
QMP-4 card, also includes a second plug (“Connector” on the picture above)
for connecting the optional QMP-4 card. Handle the 10-pin plug on the ribbon
cable assembly with care. Perform the following steps to install the QMP-4:
• turn off the power to the console;
• swing the meterbridge up and back until it rests in a fully opened position;
• plug in the ribbon cable connector to the 10-pin boxed header on the
QMP-4 board (CT7);
• attach the QMP-4 preamp assembly directly to the right of the factory
installed preamp (located at the lefthand end of the meterbridge), using four
type 4-40x1/4 pan head screws and four nylon standoffs through the four
predrilled holes on the meterbridge rear (“Optional QMP-4 Area” on the
picture above); orient it to match the factory installed QMP-4;
• connect the required audio wiring to the 12-pin plug terminals on the
QMP-4 card, referring to the “Hook-Ups” chart (see pages 2-3 - 2-5);
• close the meterbridge.
This completes the optional QMP-4 installation procedure.
NOTE: There is not enough room for an optional QMP-4 Mic Preamp in
the 8 input 12-position frame.
R-55e
R-55e // July
May2004
2008
page 2 – 7
STEREO LINE INPUT
Chapter Contents
Module Overview ........................................................................ 3-2
Mutes ...................................................................................................................... 3-3
Timer Restart .......................................................................................................... 3-3
Local/Ready ............................................................................................................ 3-3
Talkback .................................................................................................................. 3-3
Hook-ups ..................................................................................... 3-4
ANALOG AUDIO CONNECTIONS ......................................................................... 3-4
CONTROL CONNECTIONS ................................................................................... 3-4
Remote ON & OFF ................................................................................................. 3-5
Cough ..................................................................................................................... 3-5
External START & STOP ....................................................................................... 3-5
Ready ...................................................................................................................... 3-5
Talkback to Control Room ...................................................................................... 3-5
On Tally ................................................................................................................... 3-6
Tally B ..................................................................................................................... 3-6
DB Connector Pinout Drawing .................................................. 3-7
R-55e / July 2004
page 3 – 1
STEREO LINE INPUT
Module Overview
SL-55e modules are for stereo line input signals.
Each module accepts two stereo sources: A and B, switched at the top
of the module. Recessed front panel multi-turn trimpots adjust the left and
right levels. Output switches assign the selected source signal to any
combination of the console’s four outputs: two stereo outputs—PGM
(program) and AUD (audition); and two mono outputs—MONO and
PRE. NOTE: the module does not need to be ON to feed the PRE output.
A CUE switch places the module’s signal on the console’s cue bus,
where it may be heard on the meterbridge mounted cue speaker and/or as
an interrupt to the console operator’s headphones and/or control room
monitor speakers. The various cue interrupt modes are programmed at the
console’s CRS-55e (Control Room/Studio) module via PCB-mounted
dipswitch. See page 5-3.
Level is set by a long-throw fader.
Channel ON (START) and OFF (STOP) switches are at the bottom of
the module. In addition to being controlled remotely, these can also be
programmed (via internal PCB-mounted dipswitch) to perform a variety
of functions, including starting and stopping external source machines,
activating control room and studio mutes, external tallies, and timer
restart. The STOP switch’s LED can be controlled by an external source
machine to act as a “ready” indicator.
All audio and control input and output signals are made via the multipin DB-25 connector mounted on the top of the module and located
underneath the hinged meterbridge.
R-55e / July 2004
page 3 – 2
STEREO LINE INPUT
All internal programming is made via PCB mounted dipswitch SW1
located on the top of the module (beneath the DB-25 connector). Note that
when a dipswitch position is thrown to the right it is ON.
Mutes
An SL-55e module can be programmed to mute speakers when the
channel is ON. The R-55e console has two mute control lines: control
room and studio. Each of these is activated by an A input source. The
dipswitch SW1 programs these muting functions:
SW1 position 4 mutes the studio when source A is ON
SW1 position 5 mutes the control room when source A is ON
Timer Restart
The console’s digital timer can be programmed to automatically reset
to zero and begin counting up when the module’s ON button is pressed.
SW1 position 6 activates timer restart
Local/Ready
The module’s channel OFF switch normally has its LED indicator
controlled by the switch itself (Local). This is the factory default setting.
However, should you wish to have the LED function as a Ready light for
an external source machine, dipswitch SW1 position 7, when thrown to the
left, passes control to the Ready input on the module’s DB-25 connector.
A closure between the Ready input (DB-25 pin 2) and Digital Ground
(DB-25 pin 19) will activate the OFF switch LED. As long as the closure
is maintained, the LED will be lit.
Talkback
Typically, one of the R-55e console’s input modules will be used for
the control room (CRS) console operator’s microphone. The third position
of the dipswitch SW1 allows that microphone to also function as a talkback
mic. It places the signal (pre-fader, pre-on/off) onto the console’s talkback
bus. When the console operator presses a TB switch on the console’s
CRS-55e Control Room/Studio module, the talkback bus (which is carrying his microphone signal) will interrupt the regular monitor signal being
fed to the studio and talent will hear his voice through the studio monitor
speakers.
In order for the studio to reply to the console operator, the SL-55e
module controlling the studio’s microphone signal must be routed to the
console’s cue bus, where it can interrupt the regular control room monitor
feed and be heard by the operator. This is accomplished by a user-supplied
TB switch in the studio. The switch provides a momentary closure
R-55e / July 2004
?
page 3 – 3
STEREO LINE INPUT
sure between the module’s DB-25 connector “TB to CR” control pin
(DB-25 pin 17) and Digital Ground (DB-25 pin 19). As long as this closure
is maintained (i.e., as long as talent holds down the studio TB button) the
module’s (pre-fader, pre-on/off) signal will be placed on the console’s Cue
bus.
Hook-Ups
As stated before, all user wiring to and from SL-55e modules takes place
at the DB-25 multi-pin connector mounted on the top of each module. There
is one connector per module. Pinout drawings on page 3-7 show all wiring
connections at a glance.
Audio Connections
These include A and B source inputs; level is +4dBu balanced.
Pin 25 – Line A Lt In SH
Pin 24 – Line A Lt In HI
Pin 12 – Line A Lt In LO
Pin 11 – Line A Rt In SH
Pin 10 – Line A Rt In HI
Pin 23 – Line A Rt In LO
Pin 22 – Line B Lt In SH
Pin 21 – Line B Lt In HI
Pin 9 – Line B Lt In LO
Pin 8 – Line B Rt In SH
Pin 7 – Line B Rt In HI
Pin 20 – Line B Rt In LO
NOTE: If you are bringing a
mono signal into the SL‑55e
and want it to go to both left
and right sides of the stereo
busses, simply bridge the left
and right sides of the input
together when wiring.
Control Connections
Functions include remote on and off, tally, ready, and start/stop for remote source machines.
Typical DB-25
connector
Pin 1 – Cough
Pin 2 – Ready
Pin 3 – Start
Pin 4 – Stop
Pin 5 – Start/Stop Com
Pin 6 – B Tally
Pin 14 – Remote On
Pin 15 – On Tally
Pin 16 – Remote Off
Pin 17 – TB to CR
Pin 18 – +5V Digital
Pin 19 – Digital Ground
R-55e / Jan
July 2014
2004
page 3 – 4
STEREO LINE INPUT
To Turn the Module ON & OFF from a Remote Location
In the case of stereo line input modules, “remote location” can also
refer to a remote source machine that is feeding its audio to the module in
question. A contact closure (which may be sourced by the external
machine), will activate the module’s channel ON and OFF switches.
REMOTE ON — Activates the module’s channel ON switch. Momentarily connect Pin 14 (Remote On) and Digital Ground (Pin 19) to latch the
module ON. (User-supplied momentary contact switch required.)
REMOTE OFF — Activates the module’s channel OFF switch.
Momentarily connect Pin 16 (Remote Off) and Digital Ground (Pin 19) to
latch the module OFF. (User-supplied momentary contact switch required.)
COUGH — Temporarily Mutes the module. Provide a closure between Pin 1 (Cough) and Digital Ground (Pin 19). This will turn the
module OFF. Note this is a non-latching mode; the module will turn ON
again as soon as the closure stops. (User-supplied momentary contact
switch required.)
To START and STOP Remote Source Machines Using Module
ON/OFF Switches
EXTERNAL START — Hook up the remote machine’s “start” control
pins to the SL-55e module’s DB-25 connector control pins: for START
wire to Pins 3 and 5.
EXTERNAL STOP — Hook up the remote machine’s “stop” control
pins to the SL-55e module’s lower DB-25 connector control pins: for
STOP wire to Pins 4 and 5.
Typical DB-25
connector
To Control the Module’s OFF Switch LED with an External Source
Machine
READY — Hook up the remote machine’s Ready output to the
SL-55e module’s DB-25 connector pin 2 (Ready) and pin 19 (Ground).
The module’s Ready port is looking for a contact closure. As long as the
closure is maintained, the module’s OFF LED will be illuminated.
Talkback to Control Room
If an SL-55e module is being used for a studio microphone, this
connection allows talkback from that studio to the console operator.
Provide a closure between Pin 17 (TB to CR) and Digital Ground (Pin 19).
This will cause the module’s pre fader signal to be sent to the console’s Cue
bus, where it may be heard by the console operator. This non-latching
condition continues until the closure is released. (Requires user-supplied
momentary action TALKBACK switch at the studio microphone location.)
R-55e / July 2004
page 3 – 5
STEREO LINE INPUT
On Tally
Lets the module’s channel ON switch control an on-air light or other
“microphone on” indicator at a remote location. This control function
provides a continuous +5 volt signal at Pin 15 (On Tally) whenever the
module is ON.
This signal can be used to control an externally powered tally light
that requires a continuous signal to function. Or an external tally light
(i.e., LED) can be powered from the input module by connecting the
external LED to Digital Ground (Pin 19) and the On Tally port. In either
case, current should not exceed 30 milliamps.
Tally B
Provides a remote indication that the module’s B source has been
selected. This control function provides a continuous closure (open
collector) between Pin 6 (Tally B) and Digital Ground (Pins 19)
whenever the B source is selected.
This closure can be used to control an externally powered tally light
that requires a continuous closure to function. An external tally light
(i.e., LED) can be powered from the input module by connecting the
external LED to +5V Digital (Pin 18) and the B Tally port. Current
should not exceed 30 milliamps.
R-55e / July 2004
page 3 – 6
STEREO LINE INPUT
SL-55e Stereo Line Input
DB Connector Pinouts
LINE A LT IN SH
LINE A LT IN HI
LINE A RT IN LO
LINE B LT IN SH
I/O PORTS
ANALOG
AND
LOGIC
LINE B LT IN HI
LINE B RT IN LO
DIGITAL GROUND
+5V DIGITAL
TB TO CR
REMOTE OFF
ON TALLY
REMOTE ON
R-55e / July 2004
25
13
12
24
11
23
10
22
9
21
8
20
7
19
6
18
5
17
4
16
3
15
2
14
1
AUDIO GROUND
LINE A LT IN LO
LINE A RT IN SH
LINE A RT IN HI
LINE B LT IN LO
LINE B RT IN SH
LINE B RT IN HI
TALLY B
START/STOP COMMON
STOP
START
READY
COUGH
page 3 – 7
OUTPUT MODULE
Output Module (OM-55e)
Chapter Contents
Module Overview ........................................................................ 4-2
Hook-ups ..................................................................................... 4-3
DB-25 Connector — AUDIO ................................................................................... 4-3
DB-9 Connector — AUDIO ..................................................................................... 4-3
DB-9 Connector — CONTROL ............................................................................... 4-4
R-55e / July 2004
page 4 – 1
OUTPUT MODULE
Output Module (OM-55e)
Module Overview
The master output module handles the console’s Program, Audition, and Mono/Mix-Minus outputs. All outputs are calibrated with
recessed front panel multi-turn trimpots.
The R-55e console has two pairs of left-right VU meters, PGM and
SWT (switched), except for the R-55e-8 (12 position frame), which has
only the SWT meter pair. The meters are located on the console’s
meterbridge. The switched meter follows the SELECT switching,
allowing the console operator to meter PGM, AUD, MONO and PRE,
and an external stereo line signal (analog, +4dBu balanced), which may
be brought into the module on its DB-25 connector.
The OM-55e module houses the master Cue LED. Whenever Cue
is activated anywhere on the console this LED will illuminate and the
CUE signal will automatically appear on the switched VU meter pair.
When cue is de-activated, the switched meter pair goes back to its
previously selected signal.
The CUE master level control sets the level of the console’s cue
signal.
Whenever CUE is activated elsewhere on the console (stereo line inputs,
the superphone module, or for studio talkback) its signal will appear at the
console’s built-in cue speaker mounted in the meterbridge. Depending on how
the CRS-55e module has been programmed, cue can also interrupt the control
room monitor speakers. The way Cue interrupts the control room/studio
outputs is determined by PCB-mounted dipswitch. See “Cue Interrupt” on page
5-3.
The OM-55e module also generates the console’s monitor signals,
which feed the Control Room and Studio modules.
At the bottom of module are the timer control buttons (the timer
display is mounted in the righthand end of the console meterbridge):
AUTO START – enables timer restart functions from programmed input
modules’ ON buttons.
START/STOP - halts the timer, holds the last count, and then restarts and
accumulates the count when depressed again.
RESET - return to zero (if the timer is stopped it will hold at zero; if it is
running it will reset to zero and immediately begin counting up).
HOLD – when held down freezes the timer display (the counter keeps on
going); when released the display catches up to the current count.
All user wiring to and from the OM-55e module takes place at
DB-25 and DB-9 multi-pin connectors mounted on top of the module
and located underneath the hinged meterbridge. All analog audio is
+4dBu balanced. Pinout drawing on page 4-5 shows all wiring connections at a glance.
R-55e / July
Dec 2004
2004
page 4 – 2
OUTPUT MODULE
Hook-Ups
As stated before, all user wiring to and from the OM-55e modules takes
place at DB-25 and DB-9 multi-pin connectors on the top of module.
DB-25 Connector – Audio
Handles External input and Program, Audition, Mono, and Pre outputs.
All signals are +4dBu balanced.
Pin 25 – PGM Lt Out SH
Pin 24 – PGM Lt Out HI
Pin 12 – PGM Lt Out LO
Pin 11 – PGM Rt Out SH
Pin 10 – PGM Rt Out HI
Pin 23 – PGM Rt Out LO
Pin 22 – AUD Lt Out SH
Pin 21 – AUD Lt Out HI
Pin 9 – AUD Lt Out LO
Pin 8 – AUD Rt Out SH
Pin 7 – AUD Rt Out HI
Pin 20 – AUD Rt Out LO
Pin 19 – MONO Out SH
Pin 18 – MONO Out HI
Pin 6 – MONO Out LO
Pin 5 – PRE Out SH
Pin 4 – PRE Out HI
Pin 17 – PRE Out LO
Pin 16 – EXT Lt In SH
Pin 15 – EXT Lt In HI
Pin 3 – EXT Lt In LO
Pin 2 – EXT Rt In SH
Pin 1 – EXT Rt In HI
Pin 14 – EXT Rt In LO
Typical DB-25
connector
DB-9 Connector – Audio
Handles CUE output.
Pin 5 – CUE Out SH
Pin 4 – CUE Out HI
Pin 9 – CUE Out LO
Typical DB-9
connector
R-55e / July 2004
page 4 – 3
OUTPUT MODULE
DB-9 Connector — Control
Handles Tally 1 and Tally 2 control connections.
Pin 3 – Tally 1 N.O.
Pin 7 – Tally 1 Com
Pin 6 – Tally 2 Com
Pin 1 – Tally 2 N.O.
Pins 2 and 8 - Audio Common
These are simple relay closures that activate whenever programmed
input modules are turned ON (see page 3-3). The Tally 1 closure is
activated whenever the CR mute is activated, and the Tally 2 closure is
activated whenever the studio mute is activated. The ports can be used to
control externally powered tally lights that requires a continuous closure
to function.
R-55e / July 2004
Typical DB-9
connector
page 4 – 4
OUTPUT MODULE
OM-55e Output Module
PGM LT OUT SH
PGM LT OUT HI
PGM RT OUT LO
AUD LT OUT SH
I/O PORTS
ANALOG
(DB-25 "B")
AUD LT OUT HI
AUD RT OUT LO
MONO OUT SH
MONO OUT HI
PRE OUT LO
EXT LT IN SH
EXT LT IN HI
EXT RT IN LO
ANALOG
OUTPUT
PORTS
(DB-9 "A")
R-55e / July 2004
CUE OUT LO
AUDIO GROUND
TALLY 1 COM
TALLY 2 COM
25
13
12
24
11
23
10
22
9
21
8
20
7
19
6
18
5
17
4
16
3
15
2
14
1
AUDIO GROUND
PGM LT OUT LO
PGM RT OUT SH
PGM RT OUT HI
AUD LT OUT LO
AUD RT OUT SH
AUD RT OUT HI
MONO OUT LO
PRE OUT SH
PRE OUT HI
EXT LT IN LO
EXT RT IN SH
EXT RT IN HI
CUE OUT SH
CUE OUT HI
TALLY 1 N.O.
AUDIO GROUND
TALLY 2 N.O.
page 4 – 5
CONTROL ROOM MODULE
Control Room/Studio
Module
(CRS-55e)
Chapter Contents
Module Overview ........................................................................ 5-2
Cue Interrupt ........................................................................................................... 5-3
CR/Cue Mute .......................................................................................................... 5-3
Studio Mute ............................................................................................................. 5-3
Studio Dim .............................................................................................................. 5-3
Hook-ups ..................................................................................... 5-4
Left DB-25 “A” Connector — AUDIO ...................................................................... 5-4
Right DB-25 “B” Connector — AUDIO ................................................................... 5-4
R-55e / July 2004
page 5 – 1
CONTROL ROOM MODULE
Control Room/Studio
Module
(CRS-55e)
Module Overview
The CRS-55e module is the R-55e console operator’s monitor module.
It allows the operator to listen to the console’s two stereo (PGM & AUD)
outputs, two mono (MONO & PRE) outputs and two external stereo line
level inputs brought directly into the module.
A recessed front panel multi-turn trimpot adjusts talkback level.
The CRS-55e module also houses three console monitor circuits,
which follow the source selection switches. They are:
CONTROL ROOM (CR)—a dedicated output designed to drive a
separate, user provided power amp/speaker system in the main control
room;
STUDIO—a second stereo output intended for a remote (i.e., non CR)
studio power amp/speaker system;
HEADPHONE (HDPN)—an additional output (w/built-in power amp)
that drives the console operator’s headphones. There are two types of
headphone output: the +4dBu balanced output at the module’s right
DB-25 connector (B), and the headphone jack mounted in the right-hand
corner of the console, which is actually the output from a built-in
headphone amplifier.
MONITOR OUTPUT—a monitor source select (without CUE or
MUTE interrupt) independent output.
The CRS-55e module has a talkback switch. When the talkback switch
is pressed (it is momentary action), any microphone assigned to talkback
bus (see page 3-3) will interrupt the regular monitor signals being sent to
the studio.
All user wiring to and from the CRS-55e module takes place at the
DB-25 multi-pin connectors mounted at the top of the module and located
underneath the hinged meterbridge. There are two connectors: the left one
accepts the external 2 source input and handles audio outputs; the right
accepts the external 1 source input and handles audio outputs. All audio
connections are stereo line level analog signals. A pinout drawing on page
5-6 shows all wiring connections at a glance.
R-55e / July 2004
page 5 – 2
CONTROL ROOM MODULE
Internal programming for the control room/studio module is made via
printed circuit board (PCB) mounted dipswitch SW1 located on the top of
the module (beneath the DB-25 connectors). Note when a dipswitch
position is thrown to the right it is ON.
Cue Interrupt
Dipswitch SW1 pos. 5-7 determines how the console’s Cue function
will interrupt regular monitor signals:
SW1 position 7 sends cue to CR left
SW1 position 6 sends cue to CR right
SW1 position 5 sends cue to HDPN*
*factory default settings
CR/Cue Mute
The audio from both the control room speakers and the console’s builtin meterbridge speaker can easily be picked up by the console operator’s
microphone. This is a potential source of feedback. For this reason the
console provides muting to the control room output and the built-in cue
speaker whenever a mic programmed for control room/HDPN3 mute is
turned ON with A selected as the input source (see page 3-3).
SW1 position 4 will mute cue and the CR output whenever an input
channel set to activate the CR mute is ON
Studio Mute
When SW1 pos 3 is activated, it automatically mutes talkback out and
the console’s studio output whenever an input module programmed for
studio/studio 2 mute is turned ON with A selected as the input source. This
is used to prevent feedback from studio mics.
Studio Dim
Input modules controlling studio microphones can be programmed to
MUTE a studio whenever the module is turned on (i.e., it’s microphone is
live). If you wish, you can have a studio DIM (drop -20dB in level) instead
of MUTE:
SW1 positions 1 causes Studio right to DIM
SW1 positions 2 causes Studio left to DIM
Note the DIM functions also affect the talkback interrupt. Note also if the studio
is muted, talkback cannot be heard. However, if the studio is programmed to DIM
instead of MUTE, talkback audio could presumably make it from the studio
monitor speakers to the open studio mic.
R-55e / July 2004
page 5 – 3
CONTROL ROOM MODULE
Hook-Ups
As stated before, all user wiring to and from the CRS-55e module takes
place at the two DB-25 multi-pin connectors mounted at the top of the
module.
Left DB-25 “A” Connector — Audio
Handles module’s External 2 Stereo inputs and studio pre, headphone
pre, and monitor pre outputs. All audio signals are analog stereo, +4dBu
balanced.
Pin 25 – Ext 2 Lt In SH
Pin 24 – Ext 2 Lt In HI
Pin 12 – Ext 2 Lt In LO
Pin 11 – Ext 2 Rt In SH
Pin 10 – Ext 2 Rt In HI
Pin 23 – Ext 2 Rt In LO
Pin 22 – ST Pre Lt Out SH
Pin 21 – ST Pre Lt Out HI
Pin 9 – ST Pre Lt Out LO
Pin 8 – ST Pre Rt Out SH
Pin 7 – ST Pre Rt Out HI
Pin 20 – ST Pre Rt Out LO
Pin 19 – HDPN Pre Lt Out SH
Pin 18 – HDPN Pre Lt Out HI
Pin 6 – HDPN Pre Lt Out LO
Pin 5 – HDPN Pre Rt Out SH
Pin 4 – HDPN Pre Rt Out HI
Pin 17 – HDPN Pre Rt Out LO
Pin 16 – MON Pre Lt Out SH
Pin 15 – MON Pre Lt Out HI
Pin 3 – MON Pre Lt Out LO
Pin 2 – MON Pre Rt Out SH
Pin 1 – MON Pre Rt Out HI
Pin 14 – MON Pre Rt Out LO
Typical DB-25
connector
Right DB-25 “B” Connector — Audio
Handles module’s External 1 Stereo inputs and studio, headphone, and
control room outputs. All audio signals are balanced analog stereo.
R-55e / July 2004
page 5 – 4
CONTROL ROOM MODULE
Pin 22 – ST Lt Out SH
Pin 21 – ST Lt Out HI
Pin 9 – ST Lt Out LO
Pin 8 – ST Rt Out SH
Pin 7 – ST Rt Out HI
Pin 20 – ST Rt Out LO
Pin 19 – HDPN Lt Out SH
Pin 18 – HDPN Lt Out HI
Pin 6 – HDPN Lt Out LO
Pin 5 – HDPN Rt Out SH
Pin 4 – HDPN Rt Out HI
Pin 17 – HDPN Rt Out LO
Pin 16 – CR Lt Out SH
Pin 15 – CR Lt Out HI
Pin 3 – CR Lt Out LO
Pin 2 – CR Rt Out SH
Pin 1 – CR Rt Out HI
Pin 14 – CR Rt Out LO
R-55e / July 2004
Typical DB-25
connector
page 5 – 5
CONTROL ROOM MODULE
CRS-55e Control Room/Studio Module
EXT 2 LT IN SH
EXT 2 LT IN HI
EXT 2 RT IN LO
ST PRE LT OUT SH
ST PRE LT OUT HI
ST PRE RT OUT LO
HDPN PRE LT OUT SH
HDPN PRE LT OUT HI
HDPN PRE RT OUT LO
MON PRE LT OUT SH
MON PRE LT OUT HI
MON PRE RT OUT LO
25
13
12
24
11
23
10
22
9
21
8
20
7
19
6
18
5
17
4
16
3
15
2
14
1
AUDIO GROUND
EXT 2 LT IN LO
EXT 2 RT IN SH
EXT 2 RT IN HI
ST PRE LT OUT LO
ST PRE RT OUT SH
ST PRE RT OUT HI
HDPN PRE LT OUT LO
HDPN PRE RT OUTSH
HDPN PRE RT OUT HI
MON PRE LT OUT LO
MON PRE RT OUT SH
MON PRE RT OUT HI
EXT 1 LT IN SH
EXT 1 LT IN HI
EXT 1 RT IN LO
ST LT OUT SH
ST LT OUT HI
I/O PORTS
(Right DB-25 "B")
ST RT OUT LO
HDPN LT OUT SH
HDPN LT OUT HI
HDPN RT OUT LO
CR LT OUT SH
CR LT OUT HI
CR RT OUT LO
R-55e / July 2004
I/O PORTS
(Left DB-25 "A")
13
25
12
24
11
23
10
22
9
21
8
20
7
19
6
18
5
17
4
16
3
15
2
14
1
AUDIO GROUND
EXT 1 LT IN LO
EXT 1 RT IN SH
EXT 1 RT IN HI
ST LT OUT LO
ST RT OUT SH
ST RT OUT HI
HDPN LT OUT LO
HDPN RT OUTSH
HDPN RT OUT HI
CR LT OUT LO
CR RT OUT SH
CR RT OUT HI
page 5 – 6
SECOND STUDIO MODULE
Second Studio Module
(SS-55e; optional)
Chapter Contents
Module Overview ........................................................................ 6-2
Cue Interrupt ........................................................................................................... 6-3
HDPN 3 Mute .......................................................................................................... 6-3
Studio 2 Mute .......................................................................................................... 6-3
Studio 2 Dim ........................................................................................................... 6-3
Hook-ups ..................................................................................... 6-4
Left DB-25 “A” Connector — AUDIO ...................................................................... 6-4
Right DB-25 “B” Connector — AUDIO ................................................................... 6-4
R-55e / July 2004
page 6 – 1
Second Studio Module
(SS-55e; optional)
Module Overview
The optional SS-55e module is similar to the CRS-55e module. The
monitor signal being sent to this studio follows the source select switching.
This switching is indentical to the control room/monitor module’s and
includes the console’s two stereo (PGM & AUD) outputs, two mono
(MONO & PRE) outputs and two external stereo line level inputs brought
directly into the module.
A recessed front panel multi-turn trimpot adjusts talkback level.
The SS-55e module also houses three console monitor circuits, which
follow the source selection switches. They are:
STUDIO—a stereo output intended for a remote studio power amp/
speaker system;
HEADPHONES (HDPN2 & HDPN3)—two additional line level
balanced outputs to drive power amplifiers for guest or produce headphones. Both pre and post fader outputs are provided.
MONITOR OUTPUT—a monitor source select (without CUE or
MUTE interrupt) independent output.
The SS-55e module has a talkback switch. When the talkback switch
is pressed (it is momentary action), any microphone assigned to talkback
bus (see pages 3-3) will interrupt the regular monitor signals being sent to
the second studio output.
All user wiring to and from the SS-55e module takes place at the
DB-25 multi-pin connectors mounted at the top of the module and located
underneath the hinged meterbridge. There are two connectors: the left one
accepts the external 2 source input and handles audio outputs; the right
accepts the external 1 source input and handles audio outputs. All audio
connections are stereo line level analog signals. A pinout drawing on page
6-6 shows all wiring connections at a glance.
R-55e / Oct 2007
page 6 – 2
Internal programming for the control room/studio module is made via
printed circuit board (PCB) mounted dipswitch SW1 located on the top of
the module (beneath the DB-25 connectors). Note when a dipswitch
position is thrown to the right it is ON.
Cue Interrupt
Dipswitch SW1 pos 5-7 determines how the console’s Cue function
will interrupt regular monitor signals:
SW1 position 7 sends cue to HDPN 3 left
SW1 position 6 sends cue to HDPN 3 right
SW1 position 5 sends cue to HDPN 2*
HDPN 3 Mute
When SW1 pos 4 is activated, it automatically mutes the console’s
headphone 3 output whenever an input module programmed for control
room/HDPN 3 mute is turned ON with A selected as the input source.
Studio 2 Mute
When SW1 pos 3 is activated, it automatically mutes talkback out and
the console’s studio 2 output whenever an input module programmed for
studio/studio 2 mute is turned ON with A selected as the input source. This
is used to prevent feedback from the studio mics.
Studio 2 Dim
Input modules controlling studio microphones can be programmed to
MUTE a studio whenever the module is turned on (i.e., it’s microphone is
live). If you wish, you can have a studio DIM (drop -20dB in level) instead
of MUTE:
SW1 positions 1 causes Studio 2 right to DIM
SW1 positions 2 causes Studio 2 left to DIM
Note the DIM functions also affect the talkback interrupt. Note also if the studio
is muted, talkback cannot be heard. However, if the studio is programmed to DIM
instead of MUTE, talkback audio could presumably make it from the studio
monitor speakers to the open studio mic.
R-55e / July 2004
page 6 – 3
Hook-Ups
As stated before, all user wiring to and from the SS-55e module takes
place at the two DB-25 multi-pin connectors mounted at the top of the
module.
Left DB-25 “A” Connector — Audio
Handles module’s External 2 Stereo inputs and studio 2 pre, headphone
2 pre, and monitor 2 pre outputs. All audio signals are analog stereo, +4dBu
balanced.
Pin 22 – ST 2 Pre Lt Out SH
Pin 21 – ST 2 Pre Lt Out HI
Pin 9 – ST Pre 2 Lt Out LO
Pin 8 – ST Pre 2 Rt Out SH
Pin 7 – ST Pre 2 Rt Out HI
Pin 20 – ST Pre 2 Rt Out LO
Pin 19 – HDPN 2 Pre Lt Out SH
Pin 18 – HDPN 2 Pre Lt Out HI
Pin 6 – HDPN 2 Pre Lt Out LO
Pin 5 – HDPN 2 Pre Rt Out SH
Pin 4 – HDPN 2 Pre Rt Out HI
Pin 17 – HDPN 2 Pre Rt Out LO
Pin 16 – MON 2 Pre Lt Out SH
Pin 15 – MON 2 Pre Lt Out HI
Pin 3 – MON 2 Pre Lt Out LO
Pin 2 – MON 2 Pre Rt Out SH
Pin 1 – MON 2 Pre Rt Out HI
Pin 14 – MON 2 Pre Rt Out LO
Typical DB-25
connector
Right DB-25 “B” Connector — Audio
Handles module’s External 1 Stereo inputs and studio 2 and headphones 2 and 3 outputs. All audio signals are balanced analog stereo.
R-55e / July 2004
page 6 – 4
Pin 22 – ST 2 Lt Out SH
Pin 21 – ST 2 Lt Out HI
Pin 9 – ST 2 Lt Out LO
Pin 8 – ST 2 Rt Out SH
Pin 7 – ST 2 Rt Out HI
Pin 20 – ST 2 Rt Out LO
Pin 19 – HDPN 2 Lt Out SH
Pin 18 – HDPN 2 Lt Out HI
Pin 6 – HDPN 2 Lt Out LO
Pin 5 – HDPN 2 Rt Out SH
Pin 4 – HDPN 2 Rt Out HI
Pin 17 – HDPN 2 Rt Out LO
Pin 16 – HDPN 3 Lt Out SH
Pin 15 – HDPN 3 Lt Out HI
Pin 3 – HDPN 3 Lt Out LO
Pin 2 – HDPN 3 Rt Out SH
Pin 1 – HDPN 3 Rt Out HI
Pin 14 – HDPN 3 Rt Out LO
R-55e / July 2004
Typical DB-25
connector
page 6 – 5
SS-55e Second Studio Module
EXT 2 LT IN SH
25
EXT 2 LT IN HI
24
EXT 2 RT IN LO
ST 2 PRE LT OUT SH
ST 2 PRE LT OUT HI
ST 2 PRE RT OUT LO
HDPN 2 PRE LT OUT SH
HDPN 2 PRE LT OUT HI
HDPN 2 PRE RT OUT LO
MON 2 PRE LT OUT SH
MON 2 PRE LT OUT HI
MON 2 PRE RT OUT LO
13
AUDIO GROUND
12
11
EXT 2 LT IN LO
23
10
22
9
21
8
20
7
19
6
18
5
17
4
16
3
15
2
14
1
EXT 2 RT IN SH
EXT 2 RT IN HI
ST2 PRE LT OUT LO
ST 2 PRE RT OUT SH
ST 2 PRE RT OUT HI
HDPN 2 PRE LT OUT LO
HDPN 2 PRE RT OUTSH
HDPN 2 PRE RT OUT HI
MON 2 PRE LT OUT LO
MON 2 PRE RT OUT SH
MON 2 PRE RT OUT HI
EXT 1 LT IN SH
EXT 1 LT IN HI
EXT 1 RT IN LO
ST 2 LT OUT SH
I/O PORTS
(Right DB-25 "B")
ST 2 LT OUT HI
ST 2 RT OUT LO
HDPN 2 LT OUT SH
HDPN 2 LT OUT HI
HDPN 2 RT OUT LO
HDPN 3 LT OUT SH
HDPN 3 LT OUT HI
HDPN 3 RT OUT LO
R-55e / July 2004
I/O PORTS
(Left DB-25 "A")
13
25
12
24
11
23
10
22
9
21
8
20
7
19
6
18
5
17
4
16
3
15
2
14
1
AUDIO GROUND
EXT 1 LT IN LO
EXT 1 RT IN SH
EXT 1 RT IN HI
ST 2 LT OUT LO
ST 2 RT OUT SH
ST 2 RT OUT HI
HDPN 2 LT OUT LO
HDPN 2 RT OUTSH
HDPN 2 RT OUT HI
HDPN 3 LT OUT LO
HDPN 3 RT OUT SH
HDPN 3 RT OUT HI
page 6 – 6
SUPERPHONE INPUT
Superphone Input
(SPN-55e; optional)
Chapter Contents
Module Overview ........................................................................ 7-2
Caller Set-Ups ........................................................................................................ 7-2
Mutes ...................................................................................................................... 7-3
Timer Restart .......................................................................................................... 7-3
Gain Trimpot ........................................................................................................... 7-3
Hook-ups ..................................................................................... 7-3
AUDIO CONNECTIONS ......................................................................................... 7-3
CONTROL CONNECTIONS ................................................................................... 7-3
Remote ON & OFF ................................................................................................. 7-4
External START & STOP ....................................................................................... 7-4
On Tally ................................................................................................................... 7-4
R-55e / July 2004
page 7 – 1
SUPERPHONE INPUT
Superphone Input
(SPN-55e; optional)
Module Overview
The SPN-55e input module is used for telephone call-ins. Caller
signals enter the module from your station hybrid. The long-throw fader
controls the level of the caller’s voice.
Output switches assign callers to any combination of the console’s
four outputs: PGM (program), AUD (audition), MONO and PRE.
A front panel trimpot at the top of the module adjusts the console’s
CALLER level.
The channel ON (red) and OFF (amber) switches are at the bottom of
the module. These can be programmed (via PCB-mounted dipswitch) to
activate control room and studio mutes, and timer restart.
All audio and control signals hook-ups are made via a multi-pin
DB-25 connector mounted on the top of the module and located underneath the hinged meterbridge.
Caller Set-Ups
Pre-air segment communication between the console operator (DJ)
and callers is via CUE button which places the caller’s voice on the
console’s cue speaker (or control room speakers/operator’s headphone if
the CRS-55e module’s cue interrupt function has been so programmed).
A typical call-in segment might proceed as follows:
Caller phones in, DJ picks up off-air during a track play to set up the
call. He assigns his mic channel and the phone module to PRE, places the
caller in CUE, and talks to the caller. Neither the DJ mic nor the phone
module need to be ON for two-way communication.
When he is ready to take the call on-air, the DJ makes sure both
modules (his mic and phone) are assigned to PGM and turns them ON. He
then deactivates caller CUE to hear the normal feed.
R-55e / July 2004
page 7 – 2
SUPERPHONE INPUT
Internal programming is accomplished via printed circuit board (PCB)
mounted dipswitch SW1, located on the top of the module (beneath the
DB-25 connector). Note when a dipswitch position is thrown to the right
it is ON.
Mutes
When the SPN-55e phone channel ON switch is pressed, it can activate
console mute functions. Dipswitch SW1 determines which of the console’s
two mute lines will be activated:
SW1 pos 5 mutes the control room when the phone module is ON*
SW1 pos 4 mutes studio when the phone module is ON
Timer Restart
When the module is turned ON, the console’s digital timer can be
programmed to automatically reset to zero and begin counting up.
SW1 pos 6 activates timer restart when the phone module’s
ON/START switch is pressed
Gain Trimpot
There is a PCB-mounted trimpot that sets Caller In port input gain.
Hook-Ups
As stated before, all user wiring to and from the SPN-55e modules
takes place at a multi-pin DB-25 connector mounted on the top of the
module.
Audio Connections
These include caller inputs and outputs. All audio signals are +4dBu
balanced analog mono.
Pin 25 – Call In SH
Pin 24 – Call In HI
Pin 12 – Call In LO
Pin 22 – Call Out SH
Pin 21 – Call Out HI
Pin 9 – Call Out LO
Control Connections
These include remote on and off, and on tally functions.
Pin 3 – Start
Pin 4 - Stop
Pin 5 - Start/Stop Common
R-55e / July 2004
page 7 – 3
SUPERPHONE INPUT
Pin 14 – Remote On
Pin 15 – ON Tally
Pin 16 - Remote Off
Pin 18 - +5V Digital
Pin 19 - Digital Ground
To Turn the Module ON & OFF from a Remote Location
REMOTE ON — Activates the module’s channel ON switch. Provide a
momentary closure between Pin 14 (Remote On) and Digital Ground (Pin 19).
This will latch the module ON. (User-supplied momentary contact switch
required.)
REMOTE OFF — Activates the module’s channel OFF switch. Provide
a momentary closure between Pin 16 (Remote Off) and Digital Ground
(Pin 19). This will latch the module OFF. (User-supplied momentary contact
switch required.)
To START and STOP Remote Source Machines Using Module ON/
OFF Switches
EXTERNAL START — Hook up the remote machine’s Start control pins
to the SPN-55e module’s DB-25 connector control pins: for START wire to
pins 3 and 5.
EXTERNAL STOP — Hook up the remote machine’s Stop control pins
to the SPN-55e module’s DB-25 connector control pins: for STOP wire to
pins 4 and 5.
When the module’s ON/START switch is pressed, a closure takes place
between START/STOP COMMON and START; when the module’s OFF
switch is pressed, a closure takes place between START/STOP COMMON
and STOP. These may be used to control a remote tape machine for recording
phone segments.
On Tally
Lets the module’s channel ON switch control an on-air light or other
“microphone on” indicator at a remote location. This control function provides a continuous +5 volt signal at Pin 15 (On Tally) whenever the module
is ON.
This signal can be used to control an externally powered tally light that
requires a continuous signal to function. Or an external tally light (i.e., LED)
can be powered from the input module by connecting the external LED to
Digital Ground (Pin 19) and the On Tally port. In either case, current should
not exceed 30 milliamps.
R-55e / July 2004
page 7 – 4
SUPERPHONE INPUT
SPN-55e Superphone Module
CALL IN SH
CALL IN HI
N/C
CALL OUT SH
I/O PORTS
ANALOG
AND
LOGIC
CALL OUT HI
N/C
DIGITAL GROUND
+5V DIGITAL
N/C
REMOTE OFF
ON TALLY
REMOTE ON
R-55e / July 2004
25
13
12
24
11
23
10
22
9
21
8
20
7
19
6
18
5
17
4
16
3
15
2
14
1
AUDIO GROUND
CALL IN LO
N/C
N/C
CALL OUT LO
N/C
N/C
N/C
START/STOP COMMON
STOP
START
N/C
N/C
page 7 – 5
LINE SELECT MODULE
Line Select Module
(LS-55e; optional)
Chapter Contents
Module Overview ................................................................................. 8-2
Internal Programming Options .......................................................... 8-2
Hook-ups .............................................................................................. 8-3
Left DB-25 “A” Connector — AUDIO INPUTS .................................................................... 8-3
Left DB-25 “A” Connector — AUDIO OUTPUTS ............................................................... 8-3
Right DB-25 “B” Connector — AUDIO INPUTS ................................................................. 8-3
DB Connector Pinout Drawing ........................................................... 8-5
R-55e / July 2004
page 8 – 1
LINE SELECT MODULE
Line Select Module
(LS-55e; optional)
Module Overview
This optional module selects one of six stereo line sources and routes
it to one stereo output, allowing you to expand the source capability of an
input channel or monitor module.
All audio input and output signals are made via two DB-25 multi-pin
connectors mounted at the top of the module and located underneath the
hinged meterbridge.
There are no internal programming options on the LS-55e module.
R-55e / July 2004
page 8 – 2
LINE SELECT MODULE
Hook-Ups
Left DB-25 “A” Connector - Audio Inputs 5, 6
Pin 25 – Line 5 Lt In SH
Pin 24 – Line 5 Lt In HI
Pin 12 – Line 5 Lt In LO
Pin 11 – Line 5 Rt In SH
Pin 10 – Line 5 Rt In HI
Pin 23 – Line 5 Rt In LO
Left DB-25 “A” Connector - Audio Outputs
Pin 19 – Line Lt Out SH
Pin 18 – Line Lt Out HI
Pin 6 – Line Lt Out LO
Pin 5 – Line Rt Out SH
Pin 4 – Line Rt Out HI
Pin 17 – Line Rt Out LO
Right DB-25 “B” Connector - Audio Inputs 1-4
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
Typical DB-25
connector
R-55e / July 2004
page 8 – 3
LINE SELECT MODULE
1
2
3
4
5
6
14
15
16
17
18
7
8
9
10
11
12
13
19
20
21
22
23
24
25
Typical DB-25
connector
R-55e / July 2004
page 8 – 4
LINE SELECT MODULE
LS-55e Line Selector Module
LINE 5 LT IN SH
LINE 5 LT IN HI
LINE 5 RT IN LO
LINE 6 LT IN SH
LINE 6 LT IN HI
LINE 6 RT IN LO
LINE LT OUT SH
LINE LT OUT HI
LINE RT OUT LO
N/C
N/C
N/C
13
25
12
24
11
23
10
22
9
21
8
20
7
19
6
18
5
17
4
16
3
15
2
14
1
N/C
LINE 5 LT IN LO
LINE 5 RT IN SH
LINE 5 RT IN HI
LINE 6 LT IN LO
LINE 6 RT IN SH
LINE 6 RT IN HI
LINE LT OUT LO
LINE RT OUT SH
LINE RT OUT HI
N/C
N/C
N/C
LINE 1 LT IN SH
LINE 1 LT IN HI
LINE 1 RT IN LO
LINE 2 LT IN SH
INPUT
PORTS
(Right DB-25 "B")
LINE 2 LT IN HI
LINE 2 RT IN LO
LINE 3 LT IN SH
LINE 3 LT IN HI
LINE 3 RT IN LO
LINE 4 LT IN SH
LINE 4 LT IN HI
LINE 4 RT IN LO
R-55e / July 2004
INPUT/OUTPUT
PORTS
(Left DB-25 "A")
13
25
12
24
11
23
10
22
9
21
8
20
7
19
6
18
5
17
4
16
3
15
2
14
1
N/C
LINE 1 LT IN LO
LINE 1 RT IN SH
LINE 1 RT IN HI
LINE 2 LT IN LO
LINE 2 RT IN SH
LINE 2 RT IN HI
LINE 3 LT IN LO
LINE 3 RT IN SH
LINE 3 RT IN HI
LINE 4 LT IN LO
LINE 4 RT IN SH
LINE 4 RT IN HI
page 8 – 5
TAPE REMOTE MODULE
Tape Remote Module
(TR-55e; optional)
Chapter Contents
Module Overview ........................................................................... 9-2
DB Connector Pinout Drawings
START/STOP Function Control I/O .......................................................................... 9-3
Full-Function Control I/O .......................................................................................... 9-4
R-55e / July 2004
page 9 – 1
TAPE REMOTE MODULE
Tape Remote Module
(TR-55e; optional)
Module Overview
This optional module is available in two versions. The
START/STOP version offers three sets of START and STOP
buttons to provide start-stop control of three remote reel-to-reel
machines. The full function version provides RTZ, FF, REW,
STOP, REC, and PLAY buttons for a single machine. LED
indicators in each switch function as tallyback indicators and
are powered by the source machine. There are no internal
connections between the tape remote panel and the console’s
power rails.
R-55e / July 2004
page 9 – 2
TAPE REMOTE MODULE
TR-55e/SS Tape Remote
Module
SW1
SW6 (STOP) COMMON
SW2
SW6 (STOP) LEDSW5 (START) COMMON
SW3
SW4
SW5
SW5 (START) LED-
I/O CONTROL
PORTS
(DB-25)
SW4 (STOP) COMMON
SW6
SW3 (START) LEDSW2 (STOP) COMMON
SW1 (START) LED-
R-55e / July 2004
25
13
12
24
11
23
10
22
9
21
8
20
7
19
6
18
5
17
4
16
3
15
2
14
1
N/C
SW6 (STOP) N.O.
SW6 (STOP) LED+
SW5 (START) N.O.
SW5 (START) LED+
SW4 (STOP) N.O.
SW4 (STOP) LED+
SW3 (START) N.O.
SW3 (START) LED+
SW2 (STOP) N.O
SW2 (STOP) LED+
SW1 (START) N.O.
SW1 (START) LED+
page 9 – 3
TAPE REMOTE MODULE
TR-55e/FF Tape Remote
Module
SW6 (PLAY) COMMON
SW1
SW6 (PLAY) LED-
SW2
SW5 (REC) COMMON
SW3
SW4
SW5
SW6
SW5 (REC) LED-
I/O CONTROL
PORTS
(DB-25)
SW4 (STOP) COMMON
SW4 (STOP) LEDSW3 (REW) COMMON
SW3 (REW) LEDSW2 (FF) COMMON
SW2 (FF) LEDSW1 (RTZ) COMMON
SW1 (RTZ) LED-
R-55e / July 2004
25
13
12
24
11
23
10
22
9
21
8
20
7
19
6
18
5
17
4
16
3
15
2
14
1
N/C
SW6 (PLAY) N.O.
SW6 (PLAY) LED+
SW5 (REC) N.O.
SW5 (REC) LED+
SW4 (STOP) N.O.
SW4 (STOP) LED+
SW3 (REW) N.O.
SW3 (REW) LED+
SW2 (FF) N.O
SW2 (FF) LED+
SW1 (RTZ) N.O.
SW1 (RTZ) LED+
page 9 – 4
METERBRIDGE
Meterbridge
Chapter Contents
Overview ...................................................................................... 10-2
Digital Timer ................................................................................ 10-2
Digital Clock ................................................................................ 10-3
Controls .................................................................................................................... 10-3
Setting the Time ....................................................................................................... 10-3
Capacitor Backup .................................................................................................... 10-3
Operational Modes .................................................................................................. 10-4
R-55e / July 2004
page 10 – 1
METERBRIDGE
Meterbridge
Overview
All three versions of the console’s meterbridge house left-right VU meters
(see “Output Module” Chapter 4) and the cue speaker. The 18-position frame
meterbridge also includes the digital timer display, and the 26-position frame
meterbridge includes the digital timer display and the digital clock.
FRAME SIZE
VU METER (pair)
TIMER CLOCK
12-POSITION
1 (SWT)
16-POSITION
2 (PGM, SWT)
1
26-POSITION
2 (PGM, SWT)
1
1
The meterbridge assembly hinges open for easy access (VU meter illumination replacement, setting the clock). Simply swing the bridge up and back
until it rests in a fully opened position.
Digital Timer
The console timer control buttons are located on the OM-55e Output Module (see page 4-2).
The timer is provided with an AUTO-RESTART function so programmed
input modules can automatically reset the timer display to zero and start a new
count, allowing the announcer to easily track his own pace.
The START/STOP button halts the timer, holds the last count, and
then restarts and accumulates the count when depressed again—perfect for
compiling tapes of desired duration.
RESET has a dual-mode capability:
- if you depress it while the timer is counting, the display will instantly
reset to zero and start a fresh count;
- if the timer is already stopped, depressing this button will reset the timer
to zero, where it will hold until start is pressed.
HOLD button allows you to hold the display for a longer viewing duration,
while still allowing the counter to continue in the background. Releasing the
button will then display the current count.
R-55e/ /July
Dec2004
2011
R-55e
page 10 – 2
METERBRIDGE
Digital Clock
The Wheatstone digital clock is a six-digit time-of-day clock with LED
display. The clock is designed with CMOS circuits and an on-board crystalcontrolled time base oscillator. The clock PCB contains the clock circuits,
clock set controls and capacitor backup on one side and displays on the other
side. Clock set controls may be accessed by opening the meterbridge cover.
Controls
The clock is controlled by two switches mounted on the bottom part of the
clock PCB assembly.
In order to keep accurate time, the oscillator must run at 32.768 KHz. The
oscillator is set to this frequency at the factory.
Setting the Time
The setting controls consist of two switches: MODE and SET. To set the
clock, open the meterbridge cover:
1) The control switches (mounted on the bottom part of clock PCB assembly)
are labelled "MODE" and "SET". "MODE" is used to scroll from seconds to
minutes to hours; "SET" is used to set the time. The procedure is to set the
clock slightly ahead of the current time, hold the second count at "00" until
the current time catches up, and then release the count.
2) Press the MODE button until the hour digits blink. Depress the SET button
until the desired hour is displayed.
3) Press the MODE button until the minute digits blink. Depress the SET button
until the desired minute count is displayed.
4) Press the MODE button until the second digits blink. Depress and hold the
SET button; the seconds display will hold at "00". When the current time
catches up to the display, release the SET button. The clock will start
counting. Hit the MODE button once more to place the clock into working
mode.
Capacitor Backup
With the meterbridge open note the super capacitor at C20. This super
capacitor is self charging. Note that the super capacitor does NOT light up the
clock display; it powers the clock crystal to keep it from losing count (it will
do this for about one hour).
Operational Modes
The standard factory default clock configuration is crystal-controlled, 12
hour mode, stand-alone operation. However, the clock will operate either
from the internal crystal controlled time base or from an ESE master (TC-89,
autodetect) signal. Because crystal time bases are subject to drift over time,
Wheatstone recommends operating the clock in the ESE slave mode for those
applications where the exact time is critical. Connect an ESE master at
connector CT6 (Pin 1 - Signal, Pin 2 - Shield).
R-55e
R-55e//July
Feb2004
06
page 10 – 3
METERBRIDGE
The clock can also be synchronized to external 60Hz or 1Hz signals. To
synchronize to a 60Hz signal, connect the signal to CT3 pin 1, using CT3 pin
2 as the ground reference, and enable synchronization to 60Hz by turning
SW7 position 3 on (SW7 position 2 should be off). To synchronize to a 1Hz
signal, connect the signal to CT4 pin 1, using CT4 pin 2 as the ground
reference, and enable synchronization to 1Hz by turning SW7 position 2 on
(SW7 position 3 should be off).
Standard operation is 12 hour mode, but the clock can be switched to
24 hour mode by turning SW7 position 1 on.
For operation in areas with low ambient light, the display can be dimmed
by turning SW7 position 4 on.
R-55e / July 2004
page 10 – 4
PARTS LIST
Parts List
Chapter Contents
QMP-4 Quad Mic Preamp ....................................................................................... 11-2
SL-55e Stereo Line Input ......................................................................................... 11-3
OM-55e Master Output ............................................................................................ 11-5
CRS-55e Control Room/Studio ............................................................................... 11-7
SS-55e Second Studio (optional) ........................................................................... 11-10
SPN-55e Superphone Input (optional) ................................................................... 11-13
LS-55e Line Select ................................................................................................. 11-15
TR-55e/FF Tape Remote (optional) ....................................................................... 11-16
TR-55e/SS Tape Remote (optional) ....................................................................... 11-17
MBE-5508 Mother Board ........................................................................................ 11-18
MBR-2000 Mother Board ........................................................................................ 11-19
MBR-5510 Mother Board ........................................................................................ 11-20
CLK-55e Clock/Timer (for 26-pos. frame) .............................................................. 11-21
TMR-55e (for 18-pos. frame) .................................................................................. 11-23
SPS-100 Power Supply .......................................................................................... 11-25
LED-3 Meter LED Lamp ......................................................................................... 11-27
R-55e-18 (26-pos.) Frame ...................................................................................... 11-28
R-55e-12 (18-pos.) Frame ...................................................................................... 11-30
R-55e-8 (12-pos.) Frame ........................................................................................ 11-32
R-55e-18 Connector Kit .......................................................................................... 11-34
R-55e-12 Connector Kit .......................................................................................... 11-35
R-55e-8 Connector Kit ............................................................................................ 11-36
R-55e Console ........................................................................................................ 11-37
R-55e Spare Parts Kit ............................................................................................. 11-38
R-55e / Nov 2007
page 11 – 1
QMP-4 QUAD MIC PREAMP PARTS LIST
ITEM#
DESCRIPTION
QTY
W#
U2, U4, U6, U8
8 PIN .3" DIP SMT SOCKET
4
245001
CT7
10PIN BOXED HEADER, STRAIGHT
1
250077
CT3, CT4
12 POSITION PLUG ON BARRIER STRIP
2
260045
CT3, CT4
12 POSITION BOXED HEADER RIGHT ANGLE
2
260057
U2, U4, U6, U8
2017 MIC PREAMP IC
4
320003
U1, U3, U5, U7
NE5532 DUAL LINEAR OP-AMP SMT
4
325001
Z1-Z16
5.1V SMT ZENER DIODE C5V1
16
355002
C1, C10, C11, C13, C19, C23, C27, C29, C34, C36, CAPACITOR, 10µF 50V ELECTROLYTIC SMT
C40, C46
12
405001
C6, C18, C30, C42
CAPACITOR, 22µF 25V ELECTROLYTIC SMT
4
405002
C12, C35
2
405003
L1-L8
FERRITE BEAD SMT 1206 PACKAGE
8
405010
C2, C7, C14, C20, C24, C31, C37, C43
CAPACITOR, 33pF 100V CERAMIC SMT
8
415002
C5, C17, C28, C41
4
415004
C4, C9, C16, C22, C26, C33, C39, C45
CAPACITOR, .001µF 50V CERAMIC SMT
8
415005
C3, C8, C15, C21, C25, C32, C38, C44
8
415007
R2, R9, R12, R16, R23, R26, R32, R38, R41, R47,
R52, R55
10 OHM 5% .25W MC1206 RESISTOR
12
435002
R10, R11, R24, R25, R39, R40, R53, R54
8
435005
R6, R20, R29, R43
1.30 KOHM 1% .25W MC1206 RESISTOR
4
435016
R1, R3, R4, R7, R14, R15, R17, R18, R21, R28,
R30, R31, R33, R34, R36, R44, R45, R46, R48
19
435023
R49
1
435023
R5, R13, R19, R27, R35, R42, R50, R56
8
435028
R8, R22, R37, R51
4
435030
CR1-CR4
1K TRIM POT SMT
4
505001
SW1
7 POSITION DIP SWITCH
1
510048
PCB_QMP4
PRINTED CIRCUIT BOARD SMT
1
700768
F1, F2
FUSE/ POLYSWITCH .3AMP SMT RESETABLE
2
835001
R-55e / July 2004
page 11 - 2
SL-55e STEREO LINE INPUT MODULE PARTS LIST
ITEM#
DESCRIPTION
QTY
W#
SL-55e
FACEPLATE
1
005521
CT1
RIGHT ANGLE 25 PIN PC MOUNT CONNECTOR .318
1
220120
6 PIN .098" PLUG FOR #26 AWG
2
230031
1
230032
CT5, CT6
6 PIN .098" HEADER
2
250065
CT3
9 PIN .098" HEADER
1
250066
U5
74ACT00 TTL SMT Quad 2-Input NAND
1
305004
U1-U4
TL072 DUAL LINEAR OP-AMP SMT
4
325003
Q1, Q2
MMBTA55 PNP SMT TRANSISTOR
2
345002
Z3
6.2V 1W ZENER DIODE
1
350013
D6, D7
1N4002W RECTIFYING 1AMP SMT DIODE
2
355001
Z1, Z2
2
355002
D1-D5, D8
1N4148 FAST SWITCHING SMT DIODE
6
355003
U6-U10
4053 SMT
5
385000
C1, C12, C24-C28, C33, C37, C39, C42
11
405002
C2, C3, C11, C32, C40, C41
6
405003
C5-C7, C9, C10, C14-C16, C18, C19, C21, C29
12
415001
C44
1
415006
C4, C8, C13, C17, C20, C23, C30, C34-C36, C38,
C43, C46, C47
14
415007
C45
1
415009
R34, R36, R46
3
435002
R27, R80, R81
3
435007
R26, R37, R50, R78
4
435009
R41
332 OHM 1% .25W 1206 RESISTOR SMT
1
435010
R29, R39, R43, R45, R48
5
435013
R30, R79
2
435015
R32, R33, R70, R71, R76, R77
6
435020
R56, R73, R75, R84
4
435021
R1, R3, R4, R7, R8, R14, R16, R17, R20, R21,
R57-R60
R2, R5, R6, R9, R15, R18, R19, R22, R28, R31,
R38, R40, R42, R44, R47, R53, R61-R69, R72
14
435023
26
435028
R74, R82, R83
3
435028
R23, R35, R52
3
435036
R54, R55
2
435039
R24, R49
2
435043
CR1, CR2
POT TRIM 100KBECKMAN 72XLR100K
2
500078A
START/STOP SWITCH
DPDT PUSHBUTTON SWITCH, MOMENTARY ACTION,
GRAY HOUSING
2
510063
R-55e / July 2004
page 11 - 3
SL-55e STEREO LINE INPUT MODULE PARTS LIST
ITEM#
QTY
W#
START/STOP SWITCH
GRAY HOUSING
2
510063
SW2-SW7
2 POLE PUSHBUTTON SWITCH, ALTERNATE ACTION
6
510097
SW1
7 POSITION RIGHT ANGLE DIP SWITCH
1
510282
FADER KNOB
WHITE FADER KNOB WITH BLACK LINE
1
520051
START SWITCH BUTTON
LB STYLE RED BUTTON
1
530057
STOP SWITCH BUTTON
LB STYLE YELLOW BUTTON
1
530060
A/B/PGM/AUD/MONO/PRE/CUE SWITCH
BUTTON
CUSTOM WHITE LIGHT PIPE BUTTON
6
530083
FADER
100MM DUAL STEREO AUDIO FADER TYPE “K”
1
540064
STOP SWITCH LED
YELLOW LED FOR R5 ON/OFF SWITCH
1
600031
START SWITCH LED
3MM RED LED FOR ON/OFF SWITCH
1
600077
DS1
HIGH INTENSITY AMBER SMT LED RIGHT ANGLE
1
605010
DS2, DS6
ULTRABRIGHT RIGHT ANGLE RED SMT LED
2
605017
DS3
ULTRABRIGHT RIGHT ANGLE GREEN SMT LED
1
605018
DS4, DS5
ULTRABRIGHT RIGHT ANGLE YELLOW SMT LED
2
605019
PCB_SL2000
1
700656
D SUB STANDOFFJACK HARDWARE 3/16" LONG
2
820047
PEM FASTENERS
4
821009
3
835001
F1-F3
R-55e / Sep 2011
DESCRIPTION
page 11 - 4
OM-55e OUTPUT MODULE PARTS LIST
ITEM#
DESCRIPTION
QTY
W#
OM-55e
FACEPLATE
1
005536
CT2
THREADED 9 PIN DB CONNECTOR-IDD9
1
200031
CT1
1
220120
10 PIN RIBBON PLUG
1
230020
3 PIN .O98” PLUG FOR #26 AWG
1
230028
CT4
3 PIN .098" HEADER
1
250062
CT2
10 PIN PC MOUNT STRAIGHT UP SMT HEADER
1
255005
U7
1
305004
U6, U21
74ACT74 TTL SMT Dual D-Type Pos-Edge-Triggered
Flip-Flop
2
305021
U1-U5, U8-U16
OP-275 DUAL LINEAR OP-AMP SMT
14
325002
Q1, Q2
2
345002
Z3
6.2V 1W ZENER DIODE
1
350013
D3-D6
4
355001
Z1, Z2
2
355002
D2
1
355003
D1
SS14 SCHOTTKY SMT DIODE
1
355004
U17-U20
74VHC4053 SMT Triple 2-Channel Analog Mux
4
385001
C22, C25-C27, C60-C62
7
405002
C20, C63, C64
3
405003
C5, C6, C12, C13
4
415001
C1-C3, C7, C14-C16, C18, C29, C30, C32, C33,
C35, C36, C38-C40, C42, C43, C48
20
415002
C50-C53, C56, C58
6
415002
C4, C8, C9-C11, C17, C19, C21, C23, C24, C28,
C31, C34, C37, C41, C44-C47, C49, C54
21
415007
C55, C57, C59
3
415007
R1, R2, R4, R5, R7, R8, R36, R37, R71, R73, R75,
R76, R79, R83, R95, R99, R103, R107
18
435002
R109, R111, R113, R114
4
435002
R14-R25, R126, R127
14
435007
R68
1
435009
R46
1
435010
R53
1
435011
R41, R44, R48, R65-R67, R69
7
435013
R3, R6, R9, R29-R31, R93, R121
8
435016
R88, R91, R118, R120
4
435020
R122-R125
4
435021
R90, R92, R116, R119
4
435022
27
435023
R11, R12, R26-R28, R33, R34, R38, R52, R54-R64, 4.99 KOHM 1% .25W MC1206 RESISTOR
R70, R72, R74, R77, R80-R82
R-55e /July 2005
page 11 - 5
OM-55e OUTPUT MODULE PARTS LIST
ITEM#
DESCRIPTION
QTY
W#
R84-R87, R89, R94, R96-R98, R100-R102,
R104-R106, R110, R112, R115, R117
19
435023
R10, R13, R32, R35, R78
5
435028
R39, R40, R42, R43, R45, R47, R49, R50, R108
9
435039
R51
1
435043
CR1-CR6
10K 15 TURN TRIM POT
6
500014
CUE POT
10KΩ SINGLE AUDIO CONDUCTIVE PLASTIC, BOURNS
1
500058
CR7-CR10
10K TRIM POT SMT
4
505002
SW1
1
510097
SW2-SW8
2 POLE PUSHBUTTON SWITCH, MOMENTARY
7
510113
CUE KNOB
1/8" COLLET KNOB, NO POINTER, NO LINE
1
520053
CUE CAP
PASTEL GREEN CAP W.BLACK LINE FOR 15MM KNOB
1
530079
EXT/ PGM/AUD/MONO/AUTO/START-STOP
SWITCH BUTTON
6
530083
RESET SWITCH BUTTON
CUSTOM RED LIGHT PIPE BUTTON
1
530084
HOLD SWITCH BUTTON
CUSTOM YELLOW LIGHT PIPE BUTTON
1
530085
K1, K2
DPDT RELAY,5V
2
550006
DS1, DS6
2
605010
DS4, DS8
ULTRABRIGHT RIGHT ANGLE RED SMT
3
605017
DS3, DS7
ULTRABRIGHT RIGHT ANGLE GREEN SMT
2
605018
DS5, DS9
ULTRABRIGHT RIGHT ANGLE YELLOW SMT
2
605019
PCB_BPSA1000
PRINTED CIRCUIT BOARD
1
700299
PCB_OM2000A
1
700655
4
820047
PEM FASTENERS
5
821009
3
835001
F1-F3
R-55e /July 2005
page 11 - 6
CRS-55e CONTROL ROOM/STUDIO MODULE PARTS LIST
ITEM#
DESCRIPTION
QTY
W#
CRS-55e
FACEPLATE
1
005537
CT2
25 PIN DB CONNECTOR
1
200018
CT1
1
220120
1
230028
3
230031
26 PIN RIBBON PLUG
1
250043
CT3
3 PIN .098" HEADER
1
250062
CT5-CT7
6 PIN .098" HEADER
3
250065
CT2
1
255003
U8, U25, U26
Flip-Flop
3
305021
U20-U22
LM675 POWER OP AMP
3
320007
U1-U7, U9-U12, U23, U24
13
325002
Q1
1
345002
Z3
6.2V 1W ZENER DIODE
1
350013
D1, D2
2
355001
Z1, Z2
2
355002
D4
1
355003
D3
1
355004
U13-U19
7
385001
C1-C3, C19-C28, C31-C33, C47, C48, C50,
C65-C68, C97-C99, C102, C105, C109-C112
32
405002
C29, C30, C95, C96, C101
5
405003
C49, C53
2
405004
C69, C71, C73, C83, C86, C89
CAPACITOR, 1µF 35V ELECTROLYTIC SMT TANTALUM
6
405005
C4, C6, C7, C9, C11, C13, C14, C16, C34, C36,
C39, C41, C43-C45, C51, C56, C58, C59, C61
C63, C75, C77, C78, C80, C82, C93, C94, C106,
C108
20
415001
10
415001
C70, C72, C74
3
415002
C85, C88, C91
3
415004
C5, C8, C10, C12, C15, C17, C18, C35, C37, C38,
C40, C42, C46, C52, C54, C55, C57, C60
C62, C64, C76, C79, C81, C92, C100, C103, C104,
C107
18
415007
10
415007
C84, C87, C90
3
415009
R147-R152
3.3 OHM 5% .25W MC1206 RESISTOR
6
435001
R6, R9, R10, R15, R20, R27, R42, R44, R55, R60,
R68, R70, R106, R115, R118, R119, R131
17
435002
R140, R156, R157, R160, R161
5
435002
F1, F5, F6
3
435005
R3, R4, R7, R12, R13, R16-R18, R21, R46, R48,
R49, R52, R53, R57, R62, R103, R104, R107
19
435007
R112, R113, R116, R133, R142
5
435007
R-55e / July 2004
page 11 - 7
ITEM#
DESCRIPTION
QTY
W#
R37
1
435010
R28, R30, R36, R38, R39
5
435013
R123, R126, R128
3
435015
R32, R87, R98, R174, R194
5
435017
R40, R72, R188, R189
4
435018
R74, R120
2
435020
R90, R92, R94, R162, R164, R166, R168, R170
8
435021
R23, R24, R31, R33, R65, R66, R88, R89, R99,
R102, R109, R110, R136, R137, R175
15
435023
R96, R100
2
435025
R5, R8, R11, R14, R19, R22, R25, R26, R43, R45, 10.0 KOHM 1% .25W MC1206 RESISTOR
R47, R50, R51, R54, R56, R58, R59, R61
R63, R64, R67, R69, R75-R86, R91, R93, R95,
R105, R108, R111, R114, R122, R125, R130
R132, R134, R135, R138, R139, R141, R143-R145, 10.0 KOHM 1% .25W MC1206 RESISTOR
R153, R154, R163, R165, R167
18
435028
26
435028
14
435028
R169, R171, R185, R186, R191, R192
6
435028
R158, R173, R187
3
435032
R97, R101
2
435034
R124, R127, R129, R146, R155, R159
16
435039
R172, R177-R184, R190, R193
11
435039
R176
1
435043
CR1
10K TRIM POT
1
500021
STUDIO/HDPN/CR POT
10K POT, DUAL AUDIO
3
500029
TB SWITCH
GRAY HOUSING
1
510063
SW2-SW7
6
510113
SW1
1
510282
STUDIO/HDPN/CR KNOB
15mm GREY COLLET KNOB FOR 1/4" SHAFT
3
520038
CR POT CAP
11mm BURGANDY CAP W/WHITE LINE FOR 15mm KNOB
1
530039
STUDIO POT CAP
11mm BLUE CAP W/WHITE LINE FOR 15mm KNOB
1
530045
TB SWITCH CAP
1
530060
HDPN POT CAP
CREAM CAP W. BLACK LINE FOR 15MM KNOB
1
530080
EXT1/EXT2/PGM/AUD/MONO/PRE SWITCH
BUTTON
6
530083
DS1, DS2
2
605010
DS3
1
605017
DS4
1
605018
DS5, DS6
2
605019
PCB_CR2000A
1
700649
4
820047
PEM FASTENERS
4
821009
R-55e / July 2004
page 11 - 8
ITEM#
DESCRIPTION
QTY
W#
U20-U22
HEATSINK FOR T-220 WITH MOUNTING PIN
3
825010
F1, F5, F6
FUSE/ POLYSWITCH .17 AMP RESETABLE
3
830043
F4
1
835001
F2, F3
FUSE/ POLYSWITCH 1.0AMP SMT RESETABLE
2
835002
R-55e / July 2004
page 11 - 9
SS-55e SECOND STUDIO MODULE PARTS LIST
ITEM#
DESCRIPTION
QTY
W#
SS-55e
FACEPLATE
1
005538
CT2
25 PIN DB CONNECTOR
1
200018
CT1
1
220120
1
230028
3
230031
26 PIN RIBBON PLUG
1
250043
CT3
3 PIN .098" HEADER
1
250062
CT5-CT7
6 PIN .098" HEADER
3
250065
CT2
1
255003
U8, U25, U26
Flip-Flop
3
305021
U20, U21
LM675 POWER OP AMP
2
320007
U1-U7, U9-U12, U23, U24
13
325002
Q1
1
345002
Z3
6.2V 1W ZENER DIODE
1
350013
D1, D2
2
355001
Z1, Z2
2
355002
D4
1
355003
D3
1
355004
U13-U19
7
385001
C1-C3, C19-C28, C31-C33, C47, C48, C50,
C65-C68, C97-C99, C102, C105, C109-C112
32
405002
C29, C30, C95, C96, C101
5
405003
C49, C53
2
405004
C69, C71, C73, C83, C86, C89
CAPACITOR, 1µF 35V ELECTROLYTIC SMT TANTALUM
6
405005
C4, C6, C7, C9, C11, C13, C14, C16, C34, C36,
C39, C41, C43-C45, C51, C56, C58, C59, C61
C63, C75, C77, C78, C80, C82, C93, C94, C106,
C108
20
415001
10
415001
C70, C72, C74
3
415002
C85, C88, C91
3
415004
C5, C8, C10, C12, C15, C17, C18, C35, C37, C38,
C40, C42, C46, C52, C54, C55, C57, C60
C62, C64, C76, C79, C81, C92, C100, C103, C104,
C107
18
415007
10
415007
C84, C87, C90
3
415009
R147-R152
6
435001
R6, R9, R10, R15, R20, R27, R42, R44, R55, R60,
R68, R70, R106, R115, R118, R119, R131
17
435002
R140, R156, R157, R160, R161
5
435002
F1, F5, F6
3
435005
R3, R4, R7, R12, R13, R16-R18, R21, R46, R48,
R49, R52, R53, R57, R62, R103, R104, R107
19
435007
R112, R113, R116, R133, R142
5
435007
R-55e / July 2004
page 11 - 10
ITEM#
DESCRIPTION
QTY
W#
R37
1
435010
R28, R30, R36, R38, R39
5
435013
R123, R126, R128
3
435015
R32, R87, R98, R174, R194
5
435017
R188, R189
2
435018
R74, R120
2
435020
R90, R92, R94, R162, R164, R166, R168, R170
8
435021
R23, R24, R31, R33, R65, R66, R88, R89, R99,
R102, R109, R110, R136, R137, R175
15
435023
R96, R100
2
435025
R47, R50, R51, R54, R56, R58, R59, R61
R63, R64, R67, R69, R75-R86, R91, R93, R95,
R105, R108, R111, R114, R122, R125, R130
R132, R134, R135, R138, R139, R141, R143-R145, 10.0 KOHM 1% .25W MC1206 RESISTOR
R153, R154, R163, R165, R167
18
435028
26
435028
14
435028
R169, R171, R185, R186, R191, R192
6
435028
R158, R173, R187
3
435032
R40, R72, R97, R101
4
435034
R124, R127, R129, R146, R155, R159
16
435039
R172, R177-R184, R190, R193
11
435039
R176
1
435043
CR1
10K TRIM POT
1
500021
STUDIO/HDPN/CR POT
10K POT, DUAL AUDIO
3
500029
TB2 SWITCH
GRAY HOUSING
1
510063
SW2-SW7
6
510113
SW1
1
510282
STUDIO2/HDPN2/HDPN3 KNOB
15mm GREY COLLET KNOB FOR 1/4" SHAFT
3
520038
STUDIO2 POT CAP
11mm BLUE CAP W/WHITE LINE FOR 15mm KNOB
1
530045
TB2 SWITCH CAP
1
530060
HDPN2/HDPN3 POT CAP
CREAM CAP W. BLACK LINE FOR 15MM KNOB
2
530080
EXT1/EXT2/PGM/AUD/MONO/PRE SWITCH
BUTTON
6
530083
TB SWITCH LAMP
T 1 3/4 MIDGET GROOVED BASE SINGLE CHIP YELLOW
LED LAMP REPLACEMENT
1
600030
DS1, DS2
2
605010
DS3
1
605017
DS4
1
605018
DS5, DS6
2
605019
PCB_CR2000A
1
700649
4
820047
PEM FASTENERS
4
821009
R-55e / July 2004
page 11 - 11
ITEM#
DESCRIPTION
QTY
W#
U20, U21
HEATSINK FOR T-220 WITH MOUNTING PIN
2
825010
F1, F5, F6
FUSE/ POLYSWITCH .17 AMP RESETABLE
3
830043
F4
1
835001
F2, F3
2
835002
R-55e / July 2004
page 11 - 12
SPN-55e SUPERPHONE MODULE PARTS LIST
ITEM#
DESCRIPTION
QTY
W#
SPN-55e
FACEPLATE
1
005523
CT1
1
220120
2
230031
1
230032
CT6, CT7
6 PIN .098" HEADER
2
250065
CT4
9 PIN .098" HEADER
1
250066
U6
1
305004
U1-U5
NE5532 DUAL LINEAR OP-AMP SMT
5
325001
Q1, Q2
2
345002
Z3
6.2V 1W ZENER DIODE
1
350013
D5, D6
2
355001
Z1, Z2
2
355002
D1-D4
4
355003
U7-U11
5
385001
C2, C3, C23, C27, C29-C31, C35, C37-C39, C44
12
405002
C10, C22, C28
3
405003
C5, C6, C8, C11, C13-C15, C17, C19, C20, C24,
C26
12
415001
C41
1
415006
C4, C7, C12, C16, C18, C21, C25, C32-C34, C36,
C40, C43, C45
14
415007
C42
1
415009
R2, R5, R6, R20, R39, R41
6
435002
R7, R8, R10, R13, R81, R82
6
435007
R42, R79
2
435009
R46
1
435010
R44, R48, R50, R52
4
435013
R80
1
435015
R12, R26, R29, R30
4
435017
R37, R38, R75-R78
6
435020
R55, R62-R68, R73, R74
10
435023
R11, R14, R28, R31
4
435026
R51, R57, R59, R69-R72, R83
18
435028
R40, R54
2
435036
R35
1
435039
R15, R32
2
435041
R34, R53
2
435043
CR1
10K TRIM POT
1
500021
R-55e / June 2004
page 11 - 13
SPN-55e SUPERPHONE MODULE PARTS LIST
ITEM#
QTY
W#
ON/OFF SWITCH
GRAY HOUSING
2
510063
SW2-SW6
5
510097
SW1
1
510282
FADER KNOB
BLUE FADER KNOB WITH WHITE LINE
1
520052
ON SWITCH CAP
LB STYLE RED BUTTON
1
530057
OFF SWITCH CAP
1
530060
CUE SWITCH BUTTON
1
530083
PGM/AUD/MONO/PRE SWITCH BUTTON
SOLID WHITE LUMA-230 BUTTON
4
530272
FADER
100MM STEREO AUDIO ALPS FADER TYPE "K"
1
540064
OFF SWITCH LED
1
600031
ON SWITCH LED
RED LED FOR R5 ON/OFF SWITCH
1
600077
DS1, DS5
2
605017
DS2
1
605018
DS3, DS4
2
605019
PCB_SPN2000
1
700657
2
820047
PEM FASTENERS
3
821009
3
835001
F1-F3
R-55e / Sep 2010
DESCRIPTION
page 11 - 14
LS-55e LINE SELECT MODULE PARTS LIST
ITEM#
DESCRIPTION
QTY
W#
LS-55e
FACEPLATE
1
005526
CT2
25 PIN DB CONNECTOR
1
200018
CT1
1
220120
26 PIN PLUG
1
250043
CT2
1
255003
R1-R12
12
435028
SW1-SW6
6 STATION 4 POLE INTERLOCKED SWITCH, 12.5MM
SPACING
1
510040
1-6 SWITCH BUTTON
SOLID GREY LUMA-230 BUTTON
6
530273
PCB_LS2600
1
700679
4
820047
PEM FASTENERS
3
821009
R-55e / Dec 2004
page 11 - 15
TR-55e/FF TAPE REMOTE MODULE PARTS LIST
ITEM#
DESCRIPTION
QTY
W#
TR-55e/FF
FACEPLATE
1
005530
CT1
1
220120
R1-R6
6
435015
SW1-SW6
6
510113
RTZ/FF/REW/STOP/REC/PLAY BUTTON
6
530083
DS1, DS3, DS5
3
605017
DS2, DS4, DS6
3
605018
PCB_TR2000
1
700658
PEM FASTENERS
4
821009
R-55e /Dec 2004
page 11 - 16
TR-55e/SS TAPE REMOTE MODULE PARTS LIST
ITEM#
DESCRIPTION
QTY
W#
TR-55e/SS
FACEPLATE
1
005531
CT1
1
220120
R1-R6
6
435015
SW1-SW6
6
510113
START/STOP BUTTON
6
530083
DS1, DS3, DS5
3
605017
DS2, DS4, DS6
3
605018
PCB_TR2000
1
700658
PEM FASTENERS
4
821009
R-55e / Dec 2004
page 11 - 17
MBE-5508 MOTHER BOARD (EXTENDER) PARTS LIST
ITEM#
DESCRIPTION
QTY
W#
CT2-CT9
62 PIN PC MOUNT CARDEDGE CONNECTOR
8
220027
CT10
60 PIN BOARD-TO-BOARD MALE CONNECTOR
1
220074
CT1
60 PIN BOARD-TO-BOARD FEMALE CONNECTOR
1
220075
C2
CAPACITOR, 10µF 63V ELECTROLYTIC
1
400012
C10, C11
CAPACITOR, 1µF 35V TANTALUM ORANGE
2
400014
C5, C8, C12, C14, C16
330UF 35V ELECTROLYTIC CAPACITOR
5
400075
C1, C3, C4, C6, C7, C9, C13, C15
CAPACITOR, .1µF 50V MONOLITHIC CERAMIC
8
410005
PCB_MBE55
1
700812
R-55e / July 2004
page 11 - 18
MBR-2000 MOTHER BOARD (RIGHT) PARTS LIST
ITEM#
DESCRIPTION
QTY
W#
CT2-CT5
4
220027
CT1
1
220075
CT6, CT7, CT9, CT10
3 PIN .098" HEADER
4
250062
CT11
1
250075
CT8
2
250077
PCB_MBR2000
1
700653
R-55e / July 2004
page 11 - 19
MBR-5510 MOTHER BOARD (RIGHT) PARTS LIST
ITEM#
DESCRIPTION
QTY
W#
CT6-CT14, CT17
10
220027
CT5
1
220075
CT15, CT19
3 PIN .098" HEADER
2
250062
CT21
1
250075
CT2, CT22
2
250077
C7
CAPACITOR, 10µF 63V ELECTROLYTIC
1
400012
C14, C15
CAPACITOR, 1µF 35V TANTALUM ORANGE
2
400014
C9, C12, C16, C18, C19
330UF 35V ELECTROLYTIC CAPACITOR
5
400075
C1-C6, C8, C10, C11, C13, C17, C20
CAPACITOR, .1µF 50V MONOLITHIC CERAMIC
12
410005
PCB_MRR55
1
700813
F1, F2
FUSE/ POLYSWITCH .4AMP RESETABLE
2
830018
R-55e / Sep 2004
page 11 - 20
CLK-55e CLOCK/TIMER PARTS LIST (for 26-pos. frame)
ITEM#
DESCRIPTION
QTY
W#
CT3-CT6
HEADER MTA 02 POS .1CC CHAIR
4
230064A
Y1
1
245002
DS1-DS11
20 POSITION SNAP APART SOCKET, .1" SIL
5
250014
CT7
40 PIN BREAKAWAY HEADER STRIPS, STRAIGHT .1" SIL
0.15
250016
CT2
1
250077
U5
DS1706RESA TTL SMT 3.3V MicroMonitor
1
305054
U4
DS1306E 32KHZ RTC SMT
1
305057
U3
XCF01SV020CE PROM
1
315077
U1
XC2S30_100 SPARTAN II GATE ARRAY smt
1
315080
Q11
LT1117 3.3V 800mA REGULATOR SMT
1
335004
Q12
1
335005
Q9
PQ05DZ11 5V 1A REGULATOR WITH ENABLE SMT T/R
1
335011
Q10
MMBTA05 NPN SMT TRANSISTOR
1
345001
Q1-Q8
FDN340P 2A P-CHANNEL FET SMT TRANSISTOR
8
345005
D1
1
355001
Z1
1
355002
D2
1
355003
D3, D4
BAT54S SCHOTTKY SMT 2 SERIES DIODES 200mA
2
355006
Y1
32.768 KHZ TEMPERATURE-COMPENSATED CRYSTAL
OSCILLATOR
1
370036
C20
CAP 2.2F SUPERCAP 5.5V
1
400069A
C1, C41, C42
150UF 10V TANTALUM CAPACITOR, SMT
3
405008
C6
CAPACITOR, 33pF 100V CERAMIC 0603 SMT
1
405011
C5
CAPACITOR, 330µF 35V MID/LOW ESR ELECTROLYTIC
SMT
1
405014
C13, C14
2
415011
C27, C29, C31, C40
CAPACITOR, .01µF 50V CERAMIC 0603 SMT
4
415012
C2-C4, C7-C12, C15-C18, C21-C26, C28, C32-C39 CAPACITOR, .1µF 25V CERAMIC 0603 SMT
28
415013
C19, C30
2
415015
J3, J4
0 OHM 5% .25W JUMPER-RESISTOR
2
430100
R45
1.0 MOHM 5% .25W MC1206 RESISTOR
1
435049
R57
5.1 OHM 5% 1/16W 0603 RESISTOR SMT
1
435057
R39, R40, R44, R48, R51, R53, R60, R64, R69, R80 10.0 KOHM 1% 1/16W 0603 RESISTOR SMT
10
435060
R4, R7, R9, R11, R13, R15, R18, R21, R36, R37,
R58, R66, R71, R85
R1-R3, R6, R17, R20, R41-R43, R46, R47, R49,
R50, R52
1.00 KOHM 1% 1/16W 0603 RESISTOR SMT
14
435061
51 OHM 1% 1/16W 0603 RESISTOR SMT
14
435062
R62, R65, R70, R77
4
435065
R23, R25, R27, R29, R33, R34, R38, R61, R63, R68, 4.99 KOHM 1% 1/16W 0603 RESISTOR SMT
R75, R76, R78, R83, R84
15
435067
R54, R73
2
435068
R-55e / Sep 2004
page 11 - 21
CLK-55e CLOCK/TIMER PARTS LIST (for 26-pos. frame)
ITEM#
QTY
W#
9
435070
R24, R26, R28, R30-R32, R35, R67, R74, R79, R81, 220Ω 5% 0603 SMT RESISTOR
R86, R88
13
435073
R72, R82
2
435078
R59
3.83KΩ 1% 0603 SMT RESISTOR
1
435081
SW5
PUSHBUTTON SWITCH GREEN LED/ NO CAP
1
510094
SW6
PUSHBUTTON SWITCH RED LED/ NO CAP
1
510095
SW7
4 POSITION SMT DIP SWITCH, TAPE SEALED
1
515001
SW5
GREEN SWITCH CAP
1
530001
SW6
CLEAR BUTTON WITH WHITE FRAME AND RED
DIFFUSER
1
530266
DS12
HIGH INTENSITY RED SMT 0603 LED VERTICAL
1
605020
DS13
HIGH INTENSITY GREEN SMT 0603 LED VERTICAL
1
605023
DS1-DS6
SINGLE DIGIT LED DISPLAY
6
610004
DS8-DS11
SINGLE SEGMENT GREEN LED DISPLAY
4
610018
PCB_CLK55
1
700815
ID=.125_OD=.187_H=.12 NYLON SPACER
2
823049
1
835002
R5, R8, R10, R12, R14, R16, R19, R22, R87
F1
R-55e / Sep 2004
DESCRIPTION
page 11 - 22
TMR-55e TIMER PARTS LIST (for 18-pos. frame)
ITEM#
DESCRIPTION
QTY
W#
Y1
1
245002
DS8-DS11
20 POSITION SNAP APART SOCKET, .1" SIL
2
250014
CT7
40 PIN BREAKAWAY HEADER STRIPS, STRAIGHT .1" SIL
0.15
250016
CT2
1
250077
U5
DS1706RESA TTL SMT 3.3V MicroMonitor
1
305054
U4
DS1306E 32KHZ RTC SMT
1
305057
U3
XCF01SV020CE PROM
1
315077
U1
XC2S30_100 SPARTAN II GATE ARRAY smt
1
315080
Q11
1
335004
Q12
1
335005
Q9
PQ05DZ11 5V 1A REGULATOR WITH ENABLE SMT T/R
1
335011
Q10
1
345001
Q1-Q8
FDN340P 2A P-CHANNEL FET SMT TRANSISTOR
8
345005
D1
1
355001
Z1
1
355002
D2
1
355003
D3, D4
BAT54S SCHOTTKY SMT 2 SERIES DIODES 200mA
2
355006
Y1
32.768 KHZ TEMPERATURE-COMPENSATED CRYSTAL
OSCILLATOR
1
370036
C1, C41, C42
150UF 10V TANTALUM CAPACITOR, SMT
3
405008
C6
1
405011
C5
SMT
1
405014
C13, C14
2
415011
C27, C29, C31, C40
CAPACITOR, .01µF 50V CERAMIC 0603 SMT
4
415012
C2-C4, C7-C12, C15-C18, C21-C26, C28, C32-C39 CAPACITOR, .1µF 25V CERAMIC 0603 SMT
28
415013
C19, C30
2
415015
J3, J4
0 OHM 5% .25W JUMPER-RESISTOR
2
430100
R45
1.0 MOHM 5% .25W MC1206 RESISTOR
1
435049
R57
5.1 OHM 5% 1/16W 0603 RESISTOR SMT
1
435057
R39, R40, R44, R48, R51, R53, R60, R64, R69, R80 10.0 KOHM 1% 1/16W 0603 RESISTOR SMT
10
435060
R4, R7, R9, R11, R13, R15, R18, R21, R36, R37,
R58, R66, R71, R85
R1-R3, R6, R17, R20, R41-R43, R46, R47, R49,
R50, R52
14
435061
14
435062
R62, R65, R70, R77
4
435065
R23, R25, R27, R29, R33, R34, R38, R61, R63, R68, 4.99 KOHM 1% 1/16W 0603 RESISTOR SMT
R75, R76, R78, R83, R84
15
435067
R54, R73
2
435068
R5, R8, R10, R12, R14, R16, R19, R22, R87
9
435070
13
435073
R24, R26, R28, R30-R32, R35, R67, R74, R79, R81, 220Ω 5% 0603 SMT RESISTOR
R86, R88
R-55e / Sep 2004
page 11 - 23
TMR-55e TIMER PARTS LIST (for 18-pos. frame)
ITEM#
DESCRIPTION
QTY
W#
R72, R82
2
435078
R59
3.83KΩ 1% 0603 SMT RESISTOR
1
435081
SW7
4 POSITION SMT DIP SWITCH, TAPE SEALED
1
515001
DS12
HIGH INTENSITY RED SMT 0603 LED VERTICAL
1
605020
DS13
HIGH INTENSITY GREEN SMT 0603 LED VERTICAL
1
605023
DS8-DS11
SINGLE SEGMENT GREEN LED DISPLAY
4
610018
PCB_CLK55
1
700815
F1
1
835002
R-55e / Sep 2004
page 11 - 24
SPS-100 POWER SUPPLY PARTS LIST
ITEM#
QTY
W#
SPS POWER SUPPLY CABLE
1
007222
PSU-1 FACE BRACKET
1
007328
SPS-100 COVER
2
007355
SPS-100 CHASSIS
1
007356
SPS-100 RACK FACE
1
007357
7 1/2' BLACK POWER CORD
1
150017
40 AMP RIGHT ANGLE PCB MOUNT SOCKET ROHS
COMPLIANT
8
200116
8 POSITION RECEPTACLE HOUSING
1
200121
GROUND LUG
1
230002
CT1
POWER CORD CONNECTOR WITH PRINTED CIRCUIT
TERMINALS ROHS COMPLIANT
1
230071
CT4, CT5
3 PIN .098" HEADER
2
250062
U1
IC PROGRAMMABLE SHUNT REGULATOR ROHS
COMPLIANT
1
320034
U3
FLYBACK QUASY SMPS CONTROLLER
1
320035
U2
OPTO ROHS COMPLIANT
1
340050
D12
MB3510 BRIDGE RECTIFIER 35 AMP 1000 VOLT
1
350000
D5, D6
MBR4045 SCHOTTKY DIODE
2
350014
D3, D4
DIODE ROHS COMPLIANT
2
350038
Z1
33V 5 WATT ZENER DIODE
1
350039
D7
800V 4A BRIDGE RECTIFIER ROHS COMPLIANT
1
350042
D1, D2, D11, D13, D14
DIODE ULTRA FAST SWITCHING ROHS COMPLIANT
5
350043
D8, D10
2
355003
D9
1
355004
Z2-Z6
5.6V SMT 3WATT ZENER DIODE ROHS COMPLIANT
5
355007
RT1
10 OHMS 3 AMPS THERMISTOR ROHS COMPLIANT
1
360007
V1
250V METAL OXIDE VARISTOR ROHS COMPLIANT
1
360008
C62, C65
270UF 420V ELECTROLYTIC CAPACITOR ROHS
COMPLIANT
2
400073
C54
1
405002
C15-C18, C20-C23, C27-C30, C33-C36, C53, C64
18
405014
4
405015
L1-L4
SMT ROHS COMPLIANT
SMT
4.7µH FERRITE CHOKE FOR BUCK REGULATOR SMT
ROHS COMPLIANT
4
405017
C24, C25, C37, C43
CAPACITOR, .0047µUF 1KV CERAMIC, UL RATED
4
410015
C59, C60
2.2NF 1KV CERAMIC CAPACITOR ROHS COMPLIANT
2
410041
C1-C8, C51, C52
10
415005
C50
1
415006
C48, C58
2
415007
C57
1
415009
C14, C19, C26, C32
R-55e / Nov 2007
DESCRIPTION
page 11 - 25
ITEM#
DESCRIPTION
QTY
W#
C45, C46
CAPACITOR, 1uF 50V CERAMIC 1210 SMT ROHS
COMPLIANT
2
415016
C10-C13, C39-C42, C55
22UF 25V CERAMIC SMT CAPACITOR ROHS COMPLIANT
9
415018
C9, C38
10UF 50V CERAMIC SMT CAPACITOR ROHS COMPLIANT
2
415019
C31, C44, C56, C61
CAPACITOR, .47µF 250V METAL FILM ROHS COMPLIANT
4
420032
C63
CAPACITOR, .1µF 400V SNUBER FILM ROHS COMPLIANT
1
420068
C47, C49
2
420069
R39, R40, R64
2.2NF 250V FILM CAPACITOR WITH 16MM LEADS ROHS
COMPLIANT
1 MEG 5% 3 WATT MINIATURE FLAMEPROOF RESISTOR
ROHS COMPLIANT
3
430389
R65
11K OHM 5% 5 WATT RESISTOR
1
430402
R58, R59
2
435002
R47, R49
2
435009
R13, R14, R19, R20, R24, R25, R29-R31, R34, R37, 619 OHM 1% .25W MC1206 RESISTOR
R38
12
435013
R46, R63
2
435015
R45
1
435016
R1, R2, R4, R5, R7, R8, R10-R12, R16-R18,R22,
R23, R27, R28, R32, R33, R35, R36, R54, R55
22
435018
R51-R53
3
435020
R50
1
435021
R41, R42
2
435023
R3, R6, R9, R15, R21, R26, R56, R57
8
435028
R44
1
435037
R43
1
435039
R48
1
435041
R60-R62
3
435043
CR1
1K TRIM POT SMT
1
505001
DS1
HIGH INTENSITY GREEN LED ROHS COMPLIANT
1
600072
PCB_SPS100
1
700915
L5
1
800057
T1
COMMOM MODE LINE FILTER CHOKE ROHS
COMPLIANT
TRANSFORMER +3.3V,+5V,+8V,±16V,+36V 40W OUTPUT
ROHS COMPLIANT
1
800067
T2
TRANSFORMER +8V,±16V,+36/48V 100W OUTPUT
1
800069
PHILLIPS PANHEAD S/S SCREW
18
820019
PHILLIPS PAN HEAD MACHINE SCREW SS
3
820021
PHILLIP PANHEAD STAINLESS STEEL SCREW
4
820035
2
820047
SOCKET HEAD CAP SCREW BLACK
4
820117
1/4" HEX KEPNUTS S/Z
3
821005
WASHER #4 FLAT BLACK FW-4-032
8
822024A
RESISTOR STANDOFF
27
823011
R-55e / Nov 2007
page 11 - 26
ITEM#
QTY
W#
3/16 HEX 4-40 X 3/8" LONG BRASS/ZINC PLATE
STANDOFF
6
823085
D3-D6
HEATSINK TO-220/T-3P DIODE ROHS COMPLIANT
4
825030
U3
HEATSINK TO-220F5 CONTROLLER ROHS COMPLIANT
1
825032
F1, F2
PC MOUNT FUSE HOLDER
4
830014
F1, F2
SMALL 2 AMP FUSE
2
830015
F4
1
835002
F3
FUSE/ POLYSWITCH .160AMP SMT 1206 RESETABLE
ROHS COMPLIANT
1
835003
CT2
POWER LINE FILTER MODULE R/A
1
960015
R-55e / Nov 2007
DESCRIPTION
page 11 - 26a
LED-3 METER LED LAMP PARTS LIST
ITEM#
DESCRIPTION
QTY
W#
Q1-Q5
5
345001
C1, C2
2
415007
R2-R4, R7
4
435001
R5, R6,R8, R9
4
435004
R1
1
435015
DS1-DS8
HIGH INTENSITY YELLOW SMT LED VERTICAL
8
605013
PCB_LED3
1
700292
R-55e / July 2004
page 11 - 27
R-55e-18 26-pos. FRAME PARTS LIST
ITEM#
DESCRIPTION
QTY
W#
CLK-55e CLOCK/TIMER ASSEMBLY
1
005558
MB REAR
1
003565
PAN BRACE
1
003567
MB POWER CONNECTOR BRACKET
1
003579
BLANK FACEPLATE FOR R-55e
6
005539
QMP-4 LOADED CARD ASSEMBLY
1
005549
MBE-5508 LOADED CARD ASSEMBLY
1
005551
MBR-5510 LOADED CARD ASSEMBLY
1
005555
R55e-18 METAL ARMREST
1
005577
R55e-18 METERBRIDGE COVER
1
005578
R55e-18 FRAME PAN
1
005579
R55e-18 CONNECTOR KIT
1
005596
LED-3 LOADED CARD
4
007104
CLK-220 LENSE
1
026057A
PAINTED MDF LEFT SIDEPLATE
1
100090
PAINTED MDF RIGHT SIDEPLATE
1
100091
0.55
110024
SET RIGHT/LEFT END CAP
1
130231
SET FRONT/BACK FOAM INSERT
1
130232
3/8" WIDE X 1/16" THICK X 100' LONG BLACK FELT STRIP
0.02
130248
26 COND FLAT RIBBON CABLE
2.5
150083
29 7/8" X 17 3/4" X 31 7/8" 275D BOX TOP
1
160046
29 1/8" X 17 5/16" X 31 3/4" BOX BOTTOM
1
160047
10 PIN PLUG
5
230020
2
230028
PLASTIC SHELL CHASSIS CONNECTOR
1
230070
16 PIN RIBBON PLUG
1
250039
RTS JACK
1
260005
8
270050A
PATCH CLIPS
9
280000
PATCH CLIPS
3
280007
VU METER
4
630004
LIGHT BOX FOR AL29 METER WITHOUT LAMP OR
LAMPHOLDER
4
630008
FLAT WASHER
1
822007
SHOULDER WASHER
1
822008
4-40 X .250 HEX ZINC
27
823016
ALUMINUM CONTINUOUS HINGE, 72"X1.06" X .040"
PIN M MOLEX
R-55e / Dec 2004
14-20GA REEL
page 11 - 28
ITEM#
R-55e / July 2004
DESCRIPTION
QTY
W#
#6 THUMB SCREW
1
823029
4-40 X .50 ROUND NYLON SPACER
4
823038
4-40 X .375 THREADED HEX NYLON STANDOFF
4
823045
RECESSED BUMPER FOR #8 SCREW
4
824032
METER TERMINAL
8
826001
SPEAKER
1
960000
page 11 - 29
ITEM#
DESCRIPTION
QTY
W#
MB REAR
1
003564
PAN BRACE
1
003566
1
003579
BLANK FACEPLATE FOR R-55e
4
005539
1
005549
1
005551
TIMER ASSEMBLY FOR R55e-12
1
005552
MBR-5510 LOADED CARD ASSEMBLY
1
005555
R55e-12 FRAME PAN
1
005580
R55e-12 METERBRIDGE COVER
1
005583
1
005584
1
005595
LED-3 LOADED CARD
4
007104
CLK-220 LENSE
1
026057A
1
100090
1
100091
0.33
110024
1
130231
1
130232
0.02
130248
2.5
150083
29 7/8" X 17 3/4" X 31 7/8" 275D BOX TOP
1
160046
29 1/8" X 17 5/16" X 31 3/4" BOX BOTTOM
1
160047
10 PIN PLUG
2
230020
2
230028
1
230070
16 PIN RIBBON PLUG
1
250039
RTS JACK
1
260005
8
270050A
PATCH CLIPS
8
280000
PATCH CLIPS
3
280007
VU METER
4
630004
LAMPHOLDER
4
630008
FLAT WASHER
1
822007
SHOULDER WASHER
1
822008
27
823016
PIN M MOLEX
R-55e / July 2004
14-20GA REEL
page 11 - 30
ITEM#
R-55e / July 2004
DESCRIPTION
QTY
W#
#6 THUMB SCREW
1
823029
4-40 X .50 ROUND NYLON SPACER
4
823038
4
823045
4
824032
METER TERMINAL
8
826001
SPEAKER
1
960000
page 11 - 31
ITEM#
DESCRIPTION
QTY
W#
MBR-2000 LOADED CARD
1
003549
1
003579
BLANK FACEPLATE FOR R55e
2
005539
1
005549
1
005551
R55e-8 FRAME PAN
1
005570
R55e-8 PAN BRACE
1
005571
R55e-8 MB REAR
1
005572
R55e-8 MB COVER
1
005573
1
005574
1
005594
LED-3 LOADED CARD
2
007104
1
100090
1
100091
0.3
110024
1
130231
1
130232
0.015
130248
2
150083
29 7/8" X 17 3/4" X 31 7/8" 275D BOX TOP
1
160046
29 1/8" X 17 5/16" X 31 3/4" BOX BOTTOM
1
160047
10 PIN RIBBON PLUG
2
230020
2
230028
1
230070
16 PIN RIBBON PLUG
1
250039
RTS JACK
1
260005
8
270050A
PATCH CLIPS
2
280007
VU METER
2
630004
LAMPHOLDER
2
630008
FLAT WASHER
1
822007
SHOULDER WASHER
1
822008
19
823016
632 THUMB SCREW
1
823029
4
823045
4
824032
PIN M MOLEX
R-55e / July 2004
14-20GA REEL
page 11 - 32
ITEM#
R-55e / July 2004
DESCRIPTION
QTY
W#
METER TERMINAL
4
826001
SPEAKER
1
960000
page 11 - 33
R-55e-18 CONNECTOR KIT PARTS LIST
ITEM#
R-55e / Dec 2004
DESCRIPTION
QTY
W#
R-55e MANUAL
1
005598
DB25 INDIVIDUAL CRIMP PIN PLUG FOR 220
CONNECTOR KIT
30
200100
MALE PIN FOR DB25 PLUG, W/S 200100
759
200101
METALIZED PLASTIC STRAIGHT HOOD FOR DB25 PLUG,
W/S 200100
9 POSITION PLASTIC HOOD, 4-40 JACK SCREWS AND
STRAIGHT CABLE EXIT
STRAIGHT CABLE EXIT
DB9 INDIVIDUAL CRIMP PIN PLUG FOR R-55e
CONNECTOR KIT
21
200102
1
200107
9
200108
1
200109
CRIMP TOOL
1
850067
PIN EXTRACTOR TOOL FOR 220 DB PINS
1
850069
page 11 - 34
ITEM#
R-55e / Dec 2004
DESCRIPTION
QTY
W#
R-55e MANUAL
1
005598
CONNECTOR KIT
22
200100
559
200101
W/S 200100
STRAIGHT CABLE EXIT
STRAIGHT CABLE EXIT
CONNECTOR KIT
13
200102
1
200107
9
200108
1
200109
CRIMP TOOL
1
850067
1
850069
page 11 - 35
ITEM#
R-55e / Dec 2004
DESCRIPTION
QTY
W#
R-55e MANUAL
1
005598
CONNECTOR KIT
14
200100
359
200101
W/S 200100
STRAIGHT CABLE EXIT
STRAIGHT CABLE EXIT
CONNECTOR KIT
9
200102
1
200107
5
200108
1
200109
CRIMP TOOL
1
850067
1
850069
page 11 - 36
R-55e CONSOLE PARTS LIST
ITEM#
DESCRIPTION
W#
SL-55e MODULE
005501
SPN-55e MODULE
005503
LS-55e MODULE
005506
TR-55e/FF MODULE
005510
TR-55e/SS MODULE
005511
OM-55e MODULE
005516
CRS-55e MODULE
005517
SS-55e MODULE
005518
BK-55e FACEPLATE
002919
R55e-8 12-pos. WIRED FRAME
005561
005562
005563
R60 POWER SUPPLY
007010
POWER CABLE FROM CONSOLE TO PS-6040 POWER
SUPPLY
OPTIONAL SPARE PARTS KIT FOR R-55e
R-55e / July 2004
QTY
027096A
055575
page 11 - 37
SPARE PARTS KIT PARTS LIST
ITEM#
R-55e / July 2004
DESCRIPTION
QTY
W#
WIRED SELMARK CARBON STEREO FADER FOR R-55e
1
053578
CONNECTOR KIT
1
200100
10
200101
W/S 200100
1
200102
2017 MIC PREAMP IC
1
320003
LM675 POWER OP AMP
2
320007
10K POT, DUAL AUDIO
1
500029
GRAY HOUSING
2
510063
2
510097
1
510113
LB STYLE RED BUTTON
1
530057
1
530060
DPDT RELAY,5V
1
550006
1
600031
RED LED FOR R5 ON/OFF SWITCH
1
600077
PHILLIPS SERRATED PANHEAD S/S SCREW
10
820106
page 11 - 38
SCHEMATIC DRAWINGS
Schematics and Load Sheets
Chapter Contents
Console Flow Diagram ................................................................ 12-2
Quad Mic Preamp (QMP-4)
schematic ................................................................................................................. 12-3
load sheet drawing ................................................................................................... 12-4
schematic ................................................................................................................. 12-5
load sheet drawing ................................................................................................... 12-8
Output Master (OM-55e)
schematic ................................................................................................................. 12-9
load sheet drawing .................................................................................................. 12-12
Control Room/Studio (CRS-55e) & Second Studio (SS-55e)
schematic ................................................................................................................ 12-13
Superphone (SPN-55e)
schematic ................................................................................................................ 12-17
Line Select (LS-55e)
schematic ................................................................................................................ 12-21
Tape Remote (TR-55e)
schematic ................................................................................................................ 12-23
Clock/Timer (CLK-55)
schematic ................................................................................................................ 12-25
Mother Board—Extender (MBE-55)
schematic ................................................................................................................ 12-28
schematic ................................................................................................................ 12-30
schematic ................................................................................................................ 12-32
Meter LED Lamp (LED-3)
schematic ................................................................................................................ 12-35
Power Supply
SPS-100 schematic ................................................................................................ 12-37
SPS-100 load sheet drawing .................................................................................. 12-38
R-55e / July
Nov 2004
2007
page 12 – 1
LOGIC
A/B LOGIC FOLLOW
TB
COUGH
READY
START
STOP
MACHINE COMMON
ON TALLY
REMOTE OFF
REMOTE ON
ACNS
AUTO
HOLD
RESET
START
TIMER
DIP
SW
TALLY 2
RELAY
CLOCK
TIMER RESTART
LOGIC
MONITOR
STUDIO MUTE
MUTE 2
TALLY 1
RELAY
MUTE 1
TB BUS
CR MUTE
LOCAL OFF
Pwr Amp
Mute
Cue To
HDPN
SPKR
CUE LOGIC
CUE LOGIC
L
ON
OFF
LINE INPUT
L
CUE
SL-55e
H
TRIM
L
R
LINE IN
L
B
R
CUE OUT
L
L
A/B
SEL
FET
SW
L
F
A
D
E
R
TRIM
R
TRIM
MONO
L
L
L
PGM
H
L
VU
HDPN PRE
R
CUE
TRIM
L
PRE
PGM OUT
TRIM
R
PGM
AUD
H
R
R
H
L
H
L
H
VU
TRIM
AUD
R
R
L
R
PGM
ON
FET
SW
MONITOR PRE
TRIM
TB
A
H
L
CUE
MONO
PRE
L
EXT
L
TRIM
R
L
E
V
E
L
VU
FET
SWT
L
L
HDPN
R
R
VU
VU
TO PHONE
FROM PHONE
AA
BB
MODULE AA
MODULE
HDPN
JACK
Cue To
CR
MIC 1
TRIM
MIC 2
PREAMP
TO LINE INPUT
CHANNEL
(MONO)
MIC 3
L
L
AUD
L
AUD OUT
MIC PREAMP
MIC 4
PGM
H
L
QMP-4
TRIM
PRE
H
R
R
R
L
H
L
TRIM
FROM
CALLER
F
R
A
D
E
R
H
L
PGM
AUD
AUD
MONO
MONO
PRE
PRE
CUE
CUE
OFF
R
L
E
V
E
L
L
H
L
FET
CR
R
H
L
EXT1
MUTE
EXT2
TRIM
PGM
L
MONO
L
TB
TRIM
MONO
OUT
H
L
STUDIO PRE
R
H
L
TO
BB
TRIM
H
DIP
SW
L
TIMER RESTART
MUTE 2
MUTE 1
PRE OUT
TB
FET
SW
OUTPUTS
L
E
V
E
L
CONTROL ROOM/
STUDIO
OM-55e
ON
L
H
L
MUTE
FET
SW
STUDIO
R
H
L
DIM
DIPSW
CRS-55e
STOP
FROM
AA
LOGIC
STUDIO 2 MUTE
START
CUE LOGIC
PGM
PGM
AUD
AUD
MONO
MONO
PRE
PRE
H
L
L
H TO
L CALLER
R
SUM
SUPERPHONE
SPN-55e
H
L
R
H
L
L
Cue To
HDPN2
L
H
L
R
H
L
L
MONITOR 2 PRE
S
O
U
R
C
E
R
H
L
L
RTZ
FF
REW
H
L
STOP
REC
PLAY
HDPN 2 PRE
R
L
L
H
L
R
H
L
L
LINE 5
H
L
R
H
L
L
L
L
HDPN 2
R
R
Cue To
HDPN3
L
H
L
R
H
L
PGM
OUT
R
AUD
L
MONO
PRE
LINE SELECT
LS-55e
L
E
V
E
L
FET
S
E
L
E
C
T
LINE 6
Model R-55e
System Flow Diagram
H
R
LINE 4
H
L
H
L
Optional
TR/FF-55e
H
L
LINE 3
TAPE REMOTE
H
L
LINE 2
Optional
HDPN 3 MUTE
L
LINE 1
R
L
E
V
E
L
L
H
L
FET
HDPN 3
R
H
L
EXT1
EXT2
MUTE
L
TB
TRIM
H
L
STUDIO 2 PRE
R
H
L
TB
FET
SW
L
E
V
E
L
L
H
L
MUTE
FET
SW
STUDIO 2
R
H
L
STUDIO TWO
SS-55e
R-55e / July 2004
Optional
DIM
DIPSW
page 12 - 2
8
7
6
5
4
3
R8 13.3K
C1 10uF
5
330pF
3
V-
-2dBu
8
22uF C6
6
R1 4.99K
8
0.001uF
5.1V
C5V1
Z1
5.1V
C5V1
Z3
10.0K
R13
7
1.30K
SW1
R6
14
10uF
AGND
AGND
MIC 1
GAIN
TRIM
R12
10.0K
10
AGND AGND
AGND
AGND
4
AGND
-2dBu
1
R2 10
R3 4.99K
6
5
AGND
PH1
C11
+PhV
0.001uF
R5
1K 3
4.99K
C9
-
AGND
D
SH OUT 1
+4dBu BAL
C2 33pF
V+
5532
U1
+
HI
7
5532
U1
+
R9 10
R11 47
MIC1OUTLO
LO
R24 47
MIC2OUTHI
HI
VAGND
3
4.99K
AGND
C4
R14
3
1
2
R7
Z4
C5V1
5.1V
1
SH
Z2
C5V1
5.1V
2
MIC1OUTHI
1
R4 4.99K
-10dBu
4
V+
-
SSM2017
U2
+
V-
MIC1INLO
2
C5
C7 33pF
V+
V+
L2
L1
CT1
MIC 1 LO
C10 10uF
MIC1INHI
-50dBu BAL
V-
7
HI
CR1 1 2
D
R10 47
2
NOT INSTALLED
R22 13.3K
V-
4.99K
4.99K
0.001uF
Z8
C5V1 R19
5.1V
10.0K
R27
5
1.30K
SW1
R20
12
5.1V
C5V1
Z5
10uF
5.1V
C5V1
Z7
3
V-
1
AGND
MIC 2
GAIN
TRIM
R26
10.0K
AGND
4
AGND
-2dBu
1
5532
U3
+
R16 10
R17 4.99K
6
AGND
SH OUT 2
+4dBu BAL
C14 33pF
-
5
10
AGND AGND
8
2
V-
Z6
C5V1
5.1V
PH2
C19
+PhV
0.001uF
C22
R15 4.99K
V+
7
5532
U3
+
R23 10
R25 47
MIC2OUTLO
LO
V-
CT7
AGND
1
AGND
+PhV
3
+PhV
4
AGND
AGND
AGND
+Vin
5
+Vin
6
NOT INSTALLED
R37 13.3K
V-
4.99K
AGND
C26
R36
4.99K
0.001uF
Z10
C5V1
5.1V
Z12
C5V1 R35
5.1V
10.0K
5.1V
C5V1
Z9
5.1V
C5V1
Z11
R42
10uF
V-
8
2
3
-
MIC 3
GAIN
TRIM
R41
10.0K
AGND
4
AGND
-2dBu
1
5532
U5
+
R32 10
R33 4.99K
6
5
AGND
AGND
B
7
5532
U5
+
R38 10
R40 47
MIC3OUTLO
LO
AGND
CT3
2
3
R51 13.3K
R53 47
MIC4OUTHI
HI
4
5
AGND
C39
4.99K
C45
0.001uF
R56
10.0K
1
1.30K
SW1
R43
8
10uF
AGND
AGND AGND
5.1V
C5V1
Z13
AGND
5.1V
C5V1
Z15
V-
R46 4.99K
2
3
V+
V-
8
1
C37 33pF
V+
R47 10
R48 4.99K
6
AGND
4
MIC 4
GAIN
TRIM
R55
AGND
7
5532
U7
+
R52 10
R54 47
MIC4OUTLO
7
8
AGND
-2dBu
1
5532
U7
+
5
AGND
AGND
6
SSM2017
U8
+
10
PH4
C36
+PhV
0.001uF
8
22uF C42
V-
R45
3
4
1K 3
R44
4.99K
Z16
C5V1 R50
5.1V
10.0K
5
CR4 1 2
SH
Z14
C5V1
5.1V
C41
330pF
6
SH OUT 4
+4dBu BAL
9
LO
V-
10
11
AGND
12
SH
AGND
LO
MIC1INLO
HI
MIC1INHI
SH
AGND
LO
MIC2INLO
HI
MIC2INHI
SH
AGND
LO
MIC3INLO
HI
MIC3INHI
SH
AGND
LO
MIC4INLO
HI
MIC4INHI
12
11
10
9
8
7
6
5
4
3
2
1
SH
AGND
LO
MIC1OUTLO
HI
MIC1OUTHI
SH
AGND
LO
MIC2OUTLO
HI
MIC2OUTHI
SH
AGND
LO
MIC3OUTLO
HI
MIC3OUTHI
SH
AGND
LO
MIC4OUTLO
HI
MIC4OUTHI
B
CT4
3
C40 10uF
-
R49 4.99K
-2dBu
-10dBu
2
L8
L7
MIC4INLO
C43 33pF
V+
V+
-50dBu BAL
2
1
MIC4 LO
C46 10uF
MIC4INHI
CT6
HI
AGND
10
PWR
V-
NOT INSTALLED
7
-Vin
AGND
-
3
AGND
-Vin
8
1
AGND
2
3
1.30K
SW1
R29
10
R31 4.99K
SH OUT 3
+4dBu BAL
C24 33pF
V+
1
10
AGND AGND
22uF C30
6
SSM2017
U6
+
AGND
PH3
C29
+PhV
0.001uF
C33
3
V-
R30
5
CR3 1 2
SH
C28
330pF
1K 3
C27 10uF
HI
9
-2dBu
8
MIC3OUTHI
7
R34 4.99K
-10dBu
4
V+
V+
L6
L5
MIC3INLO
-
1
-50dBu BAL
2
CT5
MIC 3 LO
C34 10uF
MIC3INHI
C31 33pF
V+
7
HI
R39 47
C
AGND
2
3
C
AGND
C16
R28
3
22uF C18
6
SSM2017
U4
+
2
SH
R21
330pF
-2dBu
8
1K 3
C13 10uF
5
CR2 1 2
MIC2INLO
C17
R18 4.99K
-10dBu
4
V+
V+
L4
L3
-
1
-50dBu BAL
2
CT2
MIC 2 LO
C23 10uF
MIC2INHI
V+
7
HI
C20 33pF
NOT INSTALLED
F2
V+
C3
C15
C25
C38
C12
0.1uF
0.1uF
0.1uF
0.1uF
100uF
+Vin
POLYSW
.3A
A
QMP-4
CONTRACT NO.
AGND
C8
C21
C32
C44
C35
0.1uF
0.1uF
0.1uF
0.1uF
100uF
- Sergey Averin F1
V-
APPROVALS
-Vin
DRAWN
POLYSW
.3A
SA
DATE
4-3-03
CHECKED
SA
ISSUED
SA
W# 700768
8
R-55e/July 2004
7
6
5
4
QMP-4 Quad Mic Preamp Schematic - Sheet 1 of 1
3
A
New Bern, NC 28562
SIZE FSCM NO.
SCALE
2
DWG. NO.
D
QMP-4 PCB
16S0026
SHEET
REV
_
1 OF 1
1
page 12 - 3
SCHEMATIC DRAWINGS
QMP-4 Quad Mic Preamp - Load Sheet
R-55e / July 2004
page
page 12
12 –– 24
5
4
AGND
AGND
C12 22uF
AGND
*
TL072
U4
3
*
-2dBu
C7
R4
4
11
13
12
14
X
Y
X_Y
6
INH
U6 S 11
4053
3.32K
V-
AGND
10
AGND GND
R65
4.99K
10pF
9
-2dBu
B
11
R67
22uF C25
10.0K
1
TL072
U2
3
R53
DB8
10K
R15
SH
14
6
2
+4dBu BAL
R2
DB7
10K
DB20
HI
4
6
R66
R16
C15
AGND AGND
LO
15
6
AGND
AGND
10.0K
22uF C26
10.0K
7
R74
V+
6
4.99K
LINE
B IN
14
V+
R75
10pF
4.99K
R57
9
AGND
R64
DB22
4
220
R56
C6
10pF
R3
AGND
AGND
X_Y
X
INH
Y
U7
S
4053
X_Y
X
INH
Y
S U7
4053
R68
AGND AGND
2
5
X_Y
X
INH
Y
S U8
4053
9
AUD LT
ACN
11
AUD RT
ACN
15
MONO
ACN
X_Y
X
INH
Y
S U8
4053
1
2
3
C
5
13
X_Y
X
12
INH
Y
U9
S
4053
X_Y
X
INH
Y
S U9
4053
X_Y
X
INH
Y
U9
S
4053
19
PRE
ACN
23
CUE
ACN
25
TB
ACN
1
2
3
5
13
X_Y
X
12
INH
Y
S U10
4053
1
2
9
PGM RT
ACN
13
6
6
5
3
15
4
3
PGM LT
ACN
1
X_Y
X
12
INH
Y
U8
S
4053
X_Y
X
INH
Y
10
S U10
4053
3.32K
4.99K
10.0K
SH
5
4.99K
R59
10
6
TL072
U2
V-
DB21
10K
R18
HI
4.99K
R60
100uF C32
R50
NOT INSTALLED
6
+4dBu BAL
R5
DB9
10K
LO
8
4.99K
R58
V+
V-
88.7K
6
1
10.0K
4.99K
-14dBu
15
2
R63
R17
AGND
10pF
88.7K
R24
CT3 9 6
AGND AGND
C16
11
100uF C2
1
10K 7
AGND
6
10.0K
TL072
U1
40.2K
14
-2dBu
R61
3
NOT
INSTALLED
R49
FADER
R12
9
AGND
-2dBu
4.99K
C
R52
-2dBu
RT
GAIN
TRIM
2
221K 22.1K
6
10.0K
3.32K
R55
4
10.0K
10pF
R7
X_Y
6
INH
U6 S 9
4053
V-
10.0K
C9
4
X
Y
10
R62
5
4
220
10pF
10.0K
3
R73
C24 22uF
R26
100uF C11
10.0K
DB11
1
TL072
U3
3
R72
+4dBu BAL
22uF C27
*
R23
SH
10K
R19
DB10
R6
HI
10K
DB23
2
15
6
C29
3 100K
2 1 CRa2
1 CR2
2 3 100K
10pF
C14
4.99K
4.99K
-2dBu
-2dBu
7
13
X_Y
X
12
INH
Y
11
S U7
4053
V+
TL072
U4
5
NOT INSTALLED
44.2K
LO
*
-14dBu
INSTALL ONE TRIM ONLY
R1
R20
10pF
AGND
C18
AGND AGND
8
D
14
6
221K 22.1K
AGND
10K 3
V-
R51
AGND
4
C33 22uF
R25
CT3 1 4
40.2K
AGND
AGND
7
TL072
U1
5
-2dBu
33pF
V-
R54
4.99K
LINE
A IN
1
6
100uF C3
C22
2
3.32K
V+
6
33pF
4
X_Y
6
INH
U6 S 10
4053
C31
10pF
R8
C1 22uF
15
X
Y
V+
8
1
V-
10.0K
R83
V+
10K
R22
DB25
22uF C28
R84
C10
V-
SH
5
DB24
7
TL072
U3
NOT
INSTALLED
10pF
R11
LT
GAIN
TRIM
V+
6
+4dBu BAL
R9
HI
DB12
10K
LO
2
-2dBu
C21
3 100K
2 1 CRa1
1 CR1
2 3 100K
4.99K
10pF
-2dBu
44.2K
8
3
C5
4.99K
6
R14
R21
D
10pF
7
C19
8
X_Y
X
INH
Y
U10
S
4053
B
3
5
AGND
GND
V+
POLYSW
.3A
C40
100uF
D6
1N4002
2.43K
+Vin
R70
NOTE: PHASE SYMBOLS DENOTE SIGNAL POLARITY
F1
Vdd
C8
C20
C4
C42
C47
0.1uF
0.1uF
0.1uF
22uF
0.1uF
VIEWED FROM
ABOVE
(COMPONENT
SIDE)
Z1
C5V1
5.1V
C17
C30
C13
0.1uF
0.1uF
0.1uF
V-
2.43K
100uF
D7
1N4002
R71
-Vin
F2
C41
C39
C34
22uF
0.1uF
Z2
C5V1
5.1V
1
Xb
2
Yb
X_Yb
15
NE5532 IC PINOUT
3
Xa
X_Yc
14
4
X_Ya
Xc
13
VIEWED FROM ABOVE
(COMPONENT SIDE)
5
Ya
Yc
12
1
OUT
6
INH
A
11
2
IN-
7
VEE
B
10
3
8
VSS
C
9
4
VDD 16
3
4
Vee
5
POLYSW
.3A
SL-55e
CONTRACT NO.
2
AGND
6
V+
8
OUT
7
IN+
IN-
6
V-
IN+
5
7
- Sergey Averin -
APPROVALS
DRAWN
8
9
SA
R-55e/July 2004
7
6
5
4
3
SL-55e Stereo Line Input Module Schematic - Sheet 1 of 3
A
DATE
8-20-03
CHECKED
SA
ISSUED
SA
W# 700656
8
OUT OF PHASE
74VHC4053
IC PINOUT
VIEWED FROM ABOVE
(COMPONENT SIDE)
1
A
IN PHASE
9 PIN JST
CONNECTOR
PINOUT
New Bern, NC 28562
SIZE FSCM NO.
SCALE
2
DWG. NO.
D
SL-2000 PCB
16S0018
SHEET
REV
_
1 OF 3
1
page 12 - 5
8
7
SW2
3
4
SW3
4
SW4
4
4
4
VCC
GND
7400ACT
IC PINOUT
VIEWED FROM ABOVE
(COMPONENT SIDE)
NC
1
2
1
2
ON
ON
14
13
NO
2
VCC
3
3
ON
12
4
4
ON
11
5
5
ON
10
6
6
ON
9
7
7
ON
8
1
A
NC
5
NO
B
6
1
VCC 14
I2a
I2d 13
3
Oa
I1d 12
4
I1b
Od 11
5
I2b
I2c 10
6
Ob
I1c
9
7
VSS
Oc
8
10.0K
2
VCC
R44
1
10.0K
VCC
2
R35
VCC
22.1K
R47
1
10
10.0K
5
SW7
4
U5
C
8
74ACT00
VCC
2
6
5.49K
R13
5.49K
R69
R10
10.0K
4148 D2
CT4
1
3
5
32
MUTE2~
31
MUTE1~
30
TIMER RESTART~
4148 D4
6
CT5
CUE LOGIC~
4148 D3
4
GND
29
4148 D5
2
3
"CUE" SW
SW1
1
2
FDR
CUE SW
I1a
2
2
4
3
1
R42
NOT INSTALLED
619
R48
3
DS6
VIEWED FROM ABOVE
(COMPONENT SIDE)
10.0K
6
SW7
CUE
SW
TYPICAL 2 POLE
SWITCH PINOUT
VIEWED FROM ABOVE
(COMPONENT SIDE)
R40
1
9
C
7 POSITION
DIPSWITCH
PINOUT
2
5
SW6
619
R45
3
PRE
SW
10.0K
6
SW6
DS5
D
R38
1
5
SW5
619
R43
3
DS4
10.0K
VCC
6
SW5
MONO
SW
R28
5
SW4
332
R41
DS3
1
2
6
3
AUD
SW
2
5
SW3
619
DS2
R39
PGM
SW
3
VCC
6
3
4
NOT INSTALLED
D
5
1
5
SW2
619
A/B
SW
DS1
R29
VCC
6
7
1
2
R80
100
GND
3
1
4
5
R79
0.01uF
1.00K
6
GND
100
4
10.0K
U5
5
1
0.22uF
GND
4
5
220
R37
Q1
MMBTA55
GND
R31
10
R32
2.43K
6
VCC
VCC
VCC
2.43K
3
10.0K
R34
11
12
U5
VCC
13
F3
74ACT00
VCC
VCC
Z3
1N4735
6.2V
A
14
15
MACHINE COMMON
5
STOP
4
START
3
READY
2
COUGH
1
TB SWITCH
17
A/B LOGIC FOLLOW
6
+5V
18
DIGITAL COMMON
19
2.43K
C23
C37
0.1uF
0.1uF
22uF
- Sergey Averin -
R46 10
R27 100
VCC
VCC
VCC
VCC
APPROVALS
DRAWN
VCC
C46
C35
C38
C36
0.1uF
0.1uF
0.1uF
0.1uF
GND
55
DIG.COM.
GND
GND
SA
7
6
5
4
3
SL-55e Stereo Line Input Module Schematic - Sheet 2 of 3
A
DATE
8-20-03
CHECKED
SA
ISSUED
SA
GND
W# 700656
R-55e/July 2004
+DIG
SL-55e
CONTRACT NO.
R30 1.00K
GND
8
58
POLYSW
.3A
4148
D8
10
16
ON TALLY
C43
GND
R36
REMOTE OFF
220
R78
2.43K
Q2
MMBTA55
R77
R76
REMOTE ON
B
62 PIN
EDGE
CONNECTOR
6
74ACT00
C45
2
"OFF"SW
74ACT00
R82
CT6
OFF
SW
4148 D1
3
VCC
GND
R81
"ON"SW
B
U5
2
R33
ON
SW
C44
New Bern, NC 28562
SIZE FSCM NO.
SCALE
2
DWG. NO.
D
SL-2000 PCB
16S0018
SHEET
REV
_
2 OF 3
1
page 12 - 6
2
1
2
1
EDGE CONNECTOR BUSS CHART
CT2
B
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
N/C
47
48
N/C
49
50
51
52
53
54
55
56
57
58
59
60
61
62
N/C
N/C
SL-55 INPUTS
B
B
B
I/O PORTS
N/C
N/C
N/C
LINE "A" LT IN SH
LINE "A" LT IN HI
LINE "A" RT IN LO
LINE "B" LT IN SH
LINE "B" LT IN HI
LINE "B" RT IN LO
DIGITAL GND
+5V DIGITAL
TB TO CR
REMOTE OFF
"ON" TALLY
REMOTE ON
DB-25 CONNECTOR
A
DB1
1
DB2
2
DB3
3
DB4
4
DB5
5
DB6
6
DB7
7
DB8
8
DB9
9
DB10
10
DB11
11
DB12
12
DB13
13
14
DB14
15
DB15
16
DB16
17
DB17
18
DB18
19
DB19
20
DB20
21
DB21
22
DB22
23
DB23
24
DB24
25
DB25
A
25
24
23
22
AUDIO COMMON
LINE "A" LT IN LO
LINE "A" RT IN SH
LINE "A" RT IN HI
LINE "B" LT IN LO
LINE "B" RT IN SH
LINE "B" RT IN HI
"B" TALLY
START/STOP COM.
STOP
START
READY
COUGH
13
12
11
10
21
20
19
18
17
16
15
14
9
8
7
6
5
4
3
2
1
A
A
CT1
SL-55e
CONTRACT NO.
- Sergey Averin -
APPROVALS
DRAWN
SA
CHECKED
SA
ISSUED
SA
W# 700656
2
- Sergey Averin -
DATE
8-20-03
SIZE FSCM NO.
SCALE
APPROVALS
DRAWN
SA
New Bern, NC 28562
DWG. NO.
16S0019
B
SL-2000 PCB
SHEET
REV
_
1
2
page 12 - 7
DATE
8-20-03
CHECKED
SA
ISSUED
SA
W# 700656
3 OF 3
SL-55e Stereo Input Module Schematic - Sheet 3 of 3
R-55e/July 2004
SL-55
CONTRACT NO.
SIZE FSCM NO.
New Bern, NC 28562
DWG. NO.
16S0019
B
SCALE
SL-2000 PCB
SHEET
REV
_
3 OF 3
1
SL-55 Stereo Input Module Schematic - Sheet 3 of 3
2600/Apr 2002
Page
R-55e / July 2004
SL-55e Stereo Line Input Module - Load Sheet
page 12 – 8
8
7
6
5
+
LT
GAIN
TRIM
-
3
AGND
D
V+
-
+
+
AGND AGND
10K
RDB2
+
AGND
AGND
X_Y
X
INH
Y
S
4053
RT
GAIN
TRIM
V+
-
5
V+
PGM RT
ACN
+
-
X_Y
X
INH
Y
S
4053
V+
-
+
V-
AGND
AGND AGND
V-
V-
-
10K
HI
AGND
V+
-
+
6
35
V+
LO
V-
PGM RT
ACN~
PGM RT
TO PHONE
EXT
IN
AGND
V+
V-
V+
PGM LT
ACN
V-
AGND
SH
1
V+
+
RDB16
2
-
10K
HI
SH
4
33
3
V-
10K
LO
D
V+
PGM LT
ACN~
PGM LT
TO PHONE
4
AGND
X_Y
X
INH
Y
S
4053
+
V-
+
V-
AGND
AGND
V-
X_Y
X
INH
Y
S
4053
V+
C
AUD LT
ACN~
AUD LT
TO PHONE
V+
V+
+
X_Y
X
INH
Y
S
4053
LT
GAIN
TRIM
V-
V-
+
AGND
AUD LT
ACN
V-
-
9
X_Y
X
INH
Y
S
4053
V+
-
+
X_Y
X
INH
Y
S
4053
+
"CUE"
3
-
2
1
AGND
V-
AUD RT
ACN~
AUD RT
TO PHONE
AGND
+
V-
12
39
AGND
X_Y
X
INH
Y
S
4053
X_Y
X
INH
Y
S
4053
+
AUD RT
ACN
V+
AGND
RT
GAIN
TRIM
V+
-
11
V+
AGND
-
V-
TB
ACN
-
X_Y
X
INH
Y
S
4053
V+
-
+
AGND
+
V-
X_Y
X
INH
Y
S
4053
+
AGND
V-
B
+
C
X_Y
X
INH
Y
S
4053
V-
AGND
V+
10
37
V+
CUE
ACN
AGND
VAGND
GND
B
AGND
AGND
IN PHASE
MONO
ACN~
MONO
TO PHONE
OUT OF PHASE
+Vin
16
41
-
V+
V+
MONO
ACN
LT
GAIN
TRIM
-
15
+
AGND
V+
-
AGND
-
+
A
AGND
V-
MXM
ACN~
MXM
TO PHONE
AGND
+
V-
18
43
+
AGND
V+
V+
APPROVALS
V+
-
17
-
AGND
V-
+
V-
AGND
5
DRAWN
+
AGND
6
V+
V-
VEE
R-55e/July 2004
OM-55e
CONTRACT NO.
RT
GAIN
TRIM
+
7
V-
AGND
AGND
8
V+
-
VDD
MXM
ACN
V+
V-
V-
+
-Vin
V-
4
OM-55e Output Module Schematic - Sheet 1 of 3
SA
DATE
8-9-02
CHECKED
SA
ISSUED
SA
W# 700655
3
A
New Bern, NC 28562
SIZE FSCM NO.
SCALE
2
DWG. NO.
D
OM-2000A PCB
16S0016
SHEET
REV
A
1 OF 3
1
page 12 - 9
8
7
6
5
4
3
2
1
VCC
CUE LOGIC~
29
VCC
VCC
VCC
D
VCC
CUE LED
___
SET
CLK
D
___
CLR
EXT SW
_
Q
58
+DIG
55
DIG.COM.
74ACT00
74ACT74
GND
D
VCC
Q
62 PIN
EDGE
CONNECTOR
GND
GND
VCC
VCC
___
SET
CLK
D
___
CLR
PGM SW
Q
_
Q
74ACT00
74ACT74
VCC
62 PIN
EDGE
CONNECTOR
VCC
___
SET
CLK
C
D
___
CLR
AUD SW
Q
_
Q
C
74ACT00
74ACT74
VCC
VCC
___
SET
CLK
D
___
CLR
MONO/ PRE SW
GND
Q
_
Q
74ACT00
74ACT74
VCC
VCC
AUTO SW
VCC
MUTE1~
B
TIMER RESTART~
31
MMBTA55
3
TALLY 1 N.O.
7
TALLY 1 C.
30
B
GND
START/ STOP SW
VCC
MUTE2~
DB-9
CONNECTOR
VCC
32
MMBTA55
1
TALLY 2 N.O.
6
TALLY 2 C.
RESET SW
GND
HOLD SW
VCC
A
GND
OM-55e
CONTRACT NO.
GND
VCC
VCC
VCC
VCC
APPROVALS
DRAWN
GND
GND
GND
GND
SA
DATE
8-9-02
CHECKED
SA
ISSUED
SA
W# 700655
8
R-55e/July 2005
7
6
5
4
3
A
New Bern, NC 28562
SIZE FSCM NO.
SCALE
2
DWG. NO.
D
OM-2000A PCB
16S0017
SHEET
REV
A
2 OF 3
1
page 12 - 10
2
1
2
1
OM-90 INPUTS/OUTPUTS
Right DB-25 Connector Pinouts
B
B
B
"PGM" LT OUT SH
25
"PGM" LT OUT HI
24
"PGM" RT OUT LO
23
"AUD" LT OUT SH
22
"AUD" LT OUT HI
21
"AUD" RT OUT LO
20
"MONO" OUT SH
19
"MONO" OUT HI
18
"MXM" OUT LO
17
"EXT" LT IN SH
16
"EXT" LT IN HI
15
"EXT" RT IN LO
14
RIGHT DB-25 CONNECTOR
13
AUDIO COMMON
12
"PGM" LT OUT LO
11
"PGM" RT OUT SH
10
"PGM" RT OUT HI
9
"AUD" LT OUT LO
8
"AUD" RT OUT SH
7
"AUD" RT OUT HI
6
"MONO" OUT LO
5
"MXM" OUT SH
4
"MXM" OUT HI
3
"EXT" LT IN LO
2
"EXT" RT IN SH
1
"EXT" RT IN HI
B
Left DB-9 Connector Pinouts
A
A
TO LEFT DB-9 CONNECTOR
A
"CUE" OUT LO
9
AGND
8
TALLY 1 C.
7
TALLY 2 C.
6
5
"CUE" OUT SH
4
"CUE" OUT HI
3
TALLY 1 N.O.
2
AGND
1
TALLY 2 N.O.
A
I/O PORTS
OM-55e
CONTRACT NO.
APPROVALS
DRAWN
SA
CHECKED
SA
ISSUED
SA
W# 700655
2
DATE
8-9-02
SIZE FSCM NO.
SCALE
APPROVALS
DRAWN
SA
New Bern, NC 28562
DWG. NO.
16S0008
B
OM-2000A PCB
SHEET
REV
A
1
2
DATE
4-26-02
CHECKED
SA
ISSUED
SA
W# 700655
3 OF 3
SIZE FSCM NO.
New Bern, NC 28562
DWG. NO.
SCALE
REV
16S0009
B
OM-2000A PCB
SHEET
A
3 OF 3
1
OM-90 Output Module Schematic - Sheet 3 of 3
R-55e/July 2004
OM-90
CONTRACT NO.
page 12 - 11
R-90/Aug 2002
Page 10-13
R-55e / July 2004
OM-55e Output Module - Load Sheet
page 12 – 12
4
3
VDD
LDB24
SH
LDB25
HI
RDB10
SH
RDB11
+
0.1uF
22uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
C55
C27
C38
C52
C107
C76
C46
C81
C42
C40
C79
C37
0.1uF
22uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
LDB23
HI
LDB10
SH
LDB11
X_Y
X
INH
Y
S
4053
STUDIO
MUTE
-
+4dBu BAL
R89 4.99K
AGND
AGND AGND
STUDIO
1(2) PRE
OUT
R164 3.32K
R171 10.0K
HI
R76
-
V-
HDPN
1(2) PRE
OUT
22uF C22
22uF C24
+
V+
AGND
LO
-
LO
+
R79
V-
10.0K
10.0K
R81
A
11
7
VEE
B
10
8
VSS
C
9
1
OUT
V+
8
2
IN-
OUT
7
3
IN+
IN-
6
4
V-
IN+
5
V+
V-
AGND
V+
10.0K
10.0K
R83
INH
V+
-
AGND
AGND
V-
B
+
X_Y
X
INH
Y
S
4053
X_Y
X
INH
Y
S
4053
AGND
AGND
CRS-55e (SS-55e)
CONTRACT NO.
APPROVALS
AGND
GND
4
12
6
C
V-
DRAWN
SA
3
CRS-55e (SS-55e) Control Room (Second Studio) Module Schematic - Sheet 1 of 3
A
DATE
8-8-02
CHECKED
SA
ISSUED
SA
W# 700649
5
13
Yc
V+
+
6
Xc
Ya
+
AGND
AGND
7
X_Ya
5
-
HI
AGND
14
4
VDD 16
VIEWED FROM ABOVE
(COMPONENT SIDE)
AGND
AGND
10.0K
R85
R86
-10dBu BAL
-
22uF C26
+4dBu BAL
HI
A
R84
V-
15
X_Yc
+
X_Y
X
INH
Y
S
4053
MONITOR
PRE
OUT
X_Yb
Xa
+
10.0K
CR (HDPN3)
OUT
V-
V-
V-
AGND
HI
+
Yb
3
-
X_Y
X
INH
Y
S
4053
-
LO
+
22uF C25
+4dBu BAL
V+
V+
-10dBu BAL
V+
LO
Xb
2
AGND
X_Y
X
INH
Y
S
4053
AGND
HI
1
+
X_Y
X
INH
Y
S
4053
10.0K
LO
+
R82
+4dBu BAL
+4dBu BAL
-
74VHC4053
IC PINOUT
-
X_Y
X
INH
Y
S
4053
22uF C23
V-
OP-275
IC PINOUT
AGND
AGND
X_Y
X
INH
Y
S
4053
HI
HI
-
D
V+
+
10.0K
R77
V-
AGND
AGND
-Vin
X_Y
X
INH
Y
S
4053
10.0K
LO
+
R80
22uF C32
LO
-
F3
-
AGND
10.0K
R78
+4dBu BAL
V+
+4dBu BAL
V+
V-
V-
X_Y
INH
S
4053
X_Y
X
INH
Y
S
4053
-
HDPN
1(2) OUT
V-in
AGND
AGND
X_Y
X
INH
Y
S
4053
HI
HI
X
Y
X_Y
X
INH
Y
S
4053
LO
V+
X_Y
INH
S
4053
10.0K
R170 3.32K
AGND
X
Y
HDPN
R165 10.0K
AGND
AGND
100uF
+
V+
R166 3.32K
+4dBu BAL
-10dBu BAL
HI
-
R-55e/July 2004
R167 10.0K
V-
LO
8
R169 10.0K
R75
V-
AGND
AGND
+
C96
330uF
-
X_Y
INH
S
4053
AGND
+
V+
C49
VIEWED FROM ABOVE
(COMPONENT SIDE)
R168 3.32K
LO
+
B
R92 3.32K
+
LO
X
Y
10.0K
V+
STUDIO
INTRRPT
R93 10.0K
-
STUDIO
1(2) OUT
-
R95 10.0K
+4dBu BAL
V+
-10dBu BAL
V+
V-
AGND
R94 3.32K
HI
HI
V-
D2
1N4002
X_Y
X
INH
Y
S
4053
R91 10.0K
R90 3.32K
+
100uF
+
AGND
AGND
R163 10.0K
LO
C
330uF
-
X_Y
X
INH
Y
S
4053
+
AGND AGND
+Vin
R87 1.69K
V-
AGND
-
C95
R194 1.69K
R162 3.32K
V+
D1
1N4002
V+in
POLYSW
1.0A
C53
POLYSW
1.0A
R88 4.99K
LO
-
C5
V-
AGND AGND
EXT
2 IN
+4dBu BAL
C60
RDB23
C10
V+
LO
Z1
C5V1
5.1V
+
AGND
AGND AGND
C12
VEE
AGND
EXT
1 IN
C62
V-
V-
C15
OUT OF PHASE
HI
C57
IN PHASE
+
C92
V+
-
+4dBu BAL
C35
V+
RDB25
LDB12
C8
V-
SH
LO
F2
C28
V-
RDB24
-
1
C64
2.43K
HI
+4dBu BAL
V-
RDB12
V-
D
LO
V+
V+
V+
Z2
C5V1
5.1V
2
V+
5
R120
6
2.43K
7
R74
8
New Bern, NC 28562
SIZE FSCM NO.
SCALE
2
DWG. NO.
D
CR-2000A PCB
16S0001
SHEET
REV
A
1 OF 3
1
page 12 - 13
8
7
6
5
4
3
2
1
VCC
20.0K for HDPN3
VCC
V+
VCC
LT
CLK
GND
VCC
EXT 1
SW
VCC
X
Y
_
Q
D
___
CLR
GND
Q
AGND
CR (HP3)
LEVEL
VCC
LT
-
X_Y
INH
S
4053
AGND
AGND
CR (HDPN3)
AGND
AGND
AGND
RT
EXT 2
SW
X
Y
Q
_
Q
AGND
X_Y
INH
S
4053
AGND
VCC
VCC
AGND
AGND
V+
CLK
D
___
CLR
HDPN 1(2)
LEVEL
20.0K for HDPN3
V+
___
SET
D
+
V-
D
___
SET
-
AGND
RT
+
V-
___
SET
CLK
Q
AGND
AGND
_
Q
AGND
V-
D
___
CLR
PGM
SW
AGND
VCC
VCC
AGND
C
AGND
C
LT
CLK
_
Q
D
___
CLR
AUD
SW
VCC
Q
AGND
STUDIO 1(2)
LEVEL
VCC
RT
___
SET
CLK
AGND
X_Y
X
INH
Y
S
4053
Q
_
Q
D
___
CLR
V+
___
SET
AGND
GND
MONO
SW
AGND
VCC
V-
VCC
___
SET
CLK
D
___
CLR
B
AGND
TB 1(2)
LEVEL
Q
AGND
AGND
AGND
_
Q
PRE
SW
AGND
VCC
GND
GND
VCC
VCC
B
VCC
CUE TO CR LT
CUE TO CR RT
CUE TO HDPN
MUTE1 TO CR
MUTE2 TO STUDIO
STUDIO LT DIM
STUDIO RT DIM
1
2
3
TB
SW
VCC
GND
GND
VCC
VCC
TYPICAL 2 POLE
SWITCH PINOUT
VIEWED FROM ABOVE
(COMPONENT SIDE)
NC
A
NO
A
NC
2
___
CLRa VCC 14
____
Da CLRb 13
3
CKa
Db
12
4
PRa~ CKb
___
PRb
Qa
__
Qa
Qb
__
VSS Qb
11
1
5
2
4
3
NO
6
B
OUT OF PHASE
VIEWED FROM ABOVE
(COMPONENT SIDE)
5
1
IN PHASE
74LS74
IC PINOUT
6
7
GND
VCC
F4
58
Z3
1N4735
6.2V
10
9
C103
C17
C102
0.1uF
0.1uF
22uF
+DIG
POLYSW
.3A
8
55
DIG.COM.
6 PIN JST
CONNECTOR
PINOUT
62 PIN
EDGE
CONNECTOR
1
2
VCC
VCC
VCC
VCC
APPROVALS
DRAWN
3
GND
CRS-55e (SS-55e)
CONTRACT NO.
VIEWED FROM ABOVE
(COMPONENT SIDE)
4
C54
C100
C18
C104
5
0.1uF
0.1uF
0.1uF
0.1uF
SA
A
DATE
8-8-02
CHECKED
SA
ISSUED
SA
New Bern, NC 28562
6
GND
GND
GND
GND
W# 700649
8
R-55e/July 2004
7
6
5
4
3
CRS-55e (SS-55e) Control Room (Second Studio) Module Schematic - Sheet 2 of 3
SIZE FSCM NO.
SCALE
2
DWG. NO.
D
CR-2000A PCB
16S0002
SHEET
REV
A
2 OF 3
1
page 12 - 14
2
2
1
CR-90 (SS-90)
Control Room (Second Studio)
CT4
B
N/C
N/C
N/C
1
2
3
4
5
6
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
N/C
51
52
53
54
55
56
57
58
59
60
61
62
"EXT 2" LT IN SH
25
"EXT 2" LT IN HI
24
"EXT 2" RT IN LO
23
ST PRE LT OUT SH
22
ST PRE LT OUT HI
21
ST PRE RT OUT LO
20
HDPN PRE LT OUT SH
19
HDPN PRE LT OUT HI
18
HDPN PRE RT OUT LO
17
N/C
MON PRE LT OUT SH
16
N/C
MON PRE LT OUT HI
15
MON PRE RT OUT LO
14
B
B
Right DB-25 CONNECTOR
CT2
A
7
To Left DB-25 CONNECTOR
DB1
1
2
DB14
DB1
1
DB2
3
4
DB15
DB2
2
DB3
5
6
DB16
DB3
3
DB4
7
8
DB17
DB4
4
DB5
9
10
DB18
DB5
5
DB6
11
12
DB19
DB6
6
DB7
13
14
DB20
DB7
7
DB8
15
16
DB21
DB8
8
DB9
17
18
DB22
DB9
9
DB10
19
20
DB23
DB10
10
DB11
21
22
DB24
DB11
11
DB12
23
24
DB25
DB12
12
DB13
25
26
DB13
13
CHECKED
SA
ISSUED
SA
W# 700649
2
SIZE FSCM NO.
11
"EXT 2" RT IN SH
10
"EXT 2" RT IN HI
9
ST PRE LT OUT LO
8
ST PRE RT OUT SH
7
ST PRE RT OUT HI
6
HDPN PRE LT OUT LO
5
HDPN PRE RT OUT SH
4
HDPN PRE RT OUT HI
3
MON PRE LT OUT LO
2
MON PRE RT OUT SH
1
MON PRE RT OUT HI
"EXT 1" LT IN SH
25
"EXT 1" LT IN HI
24
"EXT 1" RT IN LO
23
16
DB16
ST LT OUT SH
22
17
DB17
ST LT OUT HI
21
18
DB18
19
DB19
ST RT OUT LO
20
20
DB20
HDPN LT OUT SH
19
21
DB21
HDPN LT OUT HI
18
22
DB22
23
DB23
HDPN RT OUT LO
17
24
DB24
CR LT OUT SH
16
25
DB25
CR LT OUT HI
15
CR RT OUT LO
14
I/O PORTS
(Right DB-25)
A
A
APPROVALS
DRAWN
SA
New Bern, NC 28562
DWG. NO.
16S0013
CR-2000A PCB
SHEET
REV
-
2
1
page 12 - 15
I/O PORTS
(Left DB-25)
13
N/C
12
"EXT 1" LT IN LO
11
"EXT 1" RT IN SH
10
"EXT 1" RT IN HI
9
ST LT OUT LO
8
ST RT OUT SH
7
ST RT OUT HI
6
HDPN LT OUT LO
5
HDPN RT OUT SH
4
HDPN RT OUT HI
3
CR LT OUT LO
2
CR RT OUT SH
1
CR RT OUT HI
A
DATE
4-25-02
CHECKED
SA
ISSUED
SA
W# 700649
3 OF 3
B
CR-90 (SS-90)
CONTRACT NO.
CRS-55e (SS-55e) Control Room (Second Studio) - Sheet 3 of 3
R-55e/July 2004
"EXT 2" LT IN LO
DB15
B
SCALE
12
DB14
DATE
8-8-02
N/C
15
CRS-55e (SS-55e)
CONTRACT NO.
13
14
CT1
APPROVALS
DRAWN
SA
1
SIZE FSCM NO.
New Bern, NC 28562
DWG. NO.
SCALE
REV
16S0013
B
CR-2000 PCB
SHEET
-
3 OF 3
1
CR-90 (SS-90) Control Room (Second Studio) - Sheet 3 of 3
R-90/Aug 2002
Page 12-17
R-55e / July 2004
CRS-55e Control Room/Studio & SS-55e Second Studio Modules - Load Sheet
page 12 – 16
8
7
6
5
4
3
R21 10.0K
R22 10.0K
C5 10pF
C13 10pF
4
AGND
R34
88.7K
C19
10pF
3 10K
2 1 CRa1
1.69K
1 CR1
2 3 10K
R30
C17 10pF
7
5532
U1
5
D
2
6
R31 8.45K
1
V+
8
D
2
R2 10
3
V-
R5 10
1
5532
U2
AGND
SH
DB25
53.6K
5
40.2K
7
5532
U3
CT4 9 6
4
+4dBu BAL
22uF C2
R13
V-
C27 22uF
22.1K
DB12
*
R17
R54
LO
6
+4dBu BAL
R15
CALL
IN
DB24
53.6K
HI
R32
NOT INSTALLED
CALL
GAIN
TRIM
V+
8
8
100
R57 10.0K
7
5532
U4
5
R14 8.45K
AGND
R36 10.0K
FADER
CALL
R12
10pF
1.69K
AGND
HI
DB22
SH
CALL
OUT
AGND
C20 10pF
AGND
C8
LO
V+
6
10K 7
DB9
DB21
4
AGND
VV+
8
6
AGND
7
5532
U5
5
100uF C22
R62 4.99K
15
6
10
4
AGND
VR63 4.99K
4
6
C
R1 10.0K
R8 100
R24 10.0K
9
R7 100
8
2
5532
U1
3
C26 10pF
1
R20 10
R25 10.0K
C29 22uF
R69 10.0K
14
6
11
C30 22uF
R70 10.0K
15
6
10
C23 22uF
R71 10.0K
4
6
9
C31 22uF
C37 22uF
R72 10.0K
X_Y
X
INH
Y
U10
S
4053
X_Y
X
INH
Y
S U10
4053
14
14
R35
2
3
AGND
5532
U5
7
5532
U2
AGND
C3 22uF
4
R6 10
6
2
AGND
R73 4.99K
R64 4.99K
V-
X_Y
X
6
INH
Y
10
U11
S
4053
4
6
9
15
6
1
10
R65 4.99K
4
6
AGND
9
3
5
R67 4.99K
15
6
10
13
15
R74 4.99K
11
AGND
40.2K
1
X_Y
X
INH
Y
S U11
4053
PGM LT
ACN
5
PGM RT
ACN
9
AUD LT
ACN
11
AUD RT
ACN
10
MONO
ACN
17
PRE
ACN
23
CUE
ACN
3
5
C
13
V+
X_Y
X
6
12
INH
Y
11
S U11
4053
B
C39 22uF
13
X_Y
X
12
INH
Y
S U10
4053
3
2
X_Y
X
12
INH
Y
11
U7
S
4053
6
5
1
6
C14 10pF
R59 10.0K
X_Y
X
INH
Y
S U7
4053
14
C11 10pF
R55 4.99K
X_Y
X
INH
Y
S U7
4053
R68 4.99K
4
6
9
1
2
R66 4.99K
14
6
11
3
5
13
X_Y
X
12
INH
Y
S U8
4053
X_Y
X
INH
Y
U8
S
4053
X_Y
X
INH
Y
S U8
4053
X_Y
X
INH
Y
U9
S
4053
X_Y
X
INH
Y
U9
S
4053
1
2
3
5
1
2
3
5
B
13
X_Y
X
12
INH
Y
S U9
4053
GND
AGND
AGND
GND
V+
POLYSW
.3A
C10
100uF
D5
1N4002
2.43K
+Vin
R75
F1
Vdd
C7
C18
C4
C44
C45
0.1uF
0.1uF
0.1uF
22uF
0.1uF
VIEWED FROM
ABOVE
(COMPONENT
SIDE)
Z1
C5V1
5.1V
C16
C25
C12
0.1uF
0.1uF
0.1uF
-Vin
V-
2.43K
100uF
D6
1N4002
R76
F2
C28
C38
C32
22uF
0.1uF
Z2
C5V1
5.1V
VDD 16
1
Xb
2
Yb
X_Yb
15
3
Xa
X_Yc
14
4
X_Ya
Xc
13
5
Ya
Yc
12
1
OUT
6
INH
A
11
2
IN-
7
VEE
B
10
3
8
VSS
C
9
4
3
NE5532 IC PINOUT
4
Vee
5
POLYSW
.3A
SPN-55e
CONTRACT NO.
2
AGND
VIEWED FROM ABOVE
(COMPONENT SIDE)
6
V+
8
OUT
7
IN+
IN-
6
V-
IN+
5
7
- Sergey Averin -
APPROVALS
DRAWN
8
9
SA
R-55e/July 2004
7
6
5
4
3
SPN-55e Superphone Module Schematic - Sheet 1 of 3
A
DATE
9-18-01
CHECKED
SA
ISSUED
SA
W# 700657
8
OUT OF PHASE
74VHC4053
IC PINOUT
VIEWED FROM ABOVE
(COMPONENT SIDE)
1
A
IN PHASE
9 PIN JST
CONNECTOR
PINOUT
New Bern, NC 28562
SIZE FSCM NO.
SCALE
2
DWG. NO.
D
SPN-2000 PCB
16S0020
SHEET
REV
_
1 OF 3
1
page 12 - 17
8
7
6
5
4
3
2
1
VCC
SW2
3
SW2
4
4
SW4
4
4
NC
1
1
ON
14
10.0K
2
2
ON
13
3
3
ON
12
4
4
ON
11
5
5
ON
10
2
VCC
ON
9
7
ON
8
3
NO
D
3
Oa
I1d 12
4
I1b
Od 11
5
I2b
B
6
I2c 10
6
Ob
I1c
9
7
VSS
Oc
8
VCC
R49
1
10.0K
VCC
2
R40
VCC
22.1K
R51
1
10
10.0K
8
U6
74ACT00
NOT INSTALLED
4
2
6
GND
4.99K
R19
C
4.99K
R16
4148 D1
CT5
1
3
5
32
MUTE2~
31
MUTE1~
30
TIMER RESTART~
4148 D3
6
CT6
CUE LOGIC~
4148 D2
4
GND
29
4148 D4
2
3
"CUE" SW
SW1
1
2
FDR
CUE SW
I2d 13
2
4
5
VCC 14
I2a
2
5
SW6
619
R52
CUE
SW
6
7
A
NC
I1a
2
10.0K
9
3
C
6
1
1
R47
1
6
SW6
DS5
VIEWED FROM ABOVE
(COMPONENT SIDE)
R45
5
SW5
619
R50
3
PRE
SW
VIEWED FROM ABOVE
(COMPONENT SIDE)
7400ACT
IC PINOUT
VIEWED FROM ABOVE
(COMPONENT SIDE)
NO
6
SW5
DS4
TYPICAL 2 POLE
SWITCH PINOUT
5
SW4
619
R48
DS3
1
6
3
MONO
SW
VCC
5
SW3
332
DS2
R46
3
7 POSITION
DIPSWITCH
PINOUT
2
6
SW3
AUD
SW
10.0K
NOT INSTALLED
619
DS1
R44
D
PGM
SW
R43
1
5
VCC
7
1
2
R81
100
AGND
3
1
4
5
C41
R80
0.01uF
1.00K
6
R83
100
CT7
1
74ACT00
0.22uF
GND
VCC
5
220
R42
GND
5
STOP
4
START
3
VCC
13
F3
74ACT00
Z3
1N4735
6.2V
C40
C21
POLYSW
C35
.3A
0.1uF
0.1uF
22uF
58
+DIG
55
DIG.COM.
10
15
MACHINE COMMON
Q2
MMBTA55
12
U6
GND
R41
16
220
R79
14
ON TALLY
11
R77
2.43K
REMOTE OFF
R39
VCC
VCC
REMOTE ON
10
R37
2.43K
Q1
MMBTA55
2.43K
4
6
B
VCC
R38
3
"OFF"SW
62 PIN
EDGE
CONNECTOR
6
U6
5
C42
2
OFF
SW
4
10.0K
2.43K
B
74ACT00
VCC
GND
GND
R82
"ON"SW
U6
2
R78
ON
SW
AGND
3
2
1
17
A
18
DIGITAL COMMON
19
SPN-55e
CONTRACT NO.
6
+5V
VCC
- Sergey Averin VCC
VCC
VCC
VCC
GND
APPROVALS
DRAWN
C43
C33
C36
C34
0.1uF
0.1uF
0.1uF
0.1uF
GND
GND
GND
GND
SA
DATE
9-18-01
CHECKED
SA
ISSUED
SA
W# 700657
8
R-55e/July 2004
7
6
5
4
3
A
New Bern, NC 28562
SIZE FSCM NO.
SCALE
2
DWG. NO.
D
SPN-2000 PCB
16S0021
SHEET
REV
_
2 OF 3
1
page 12 - 18
2
1
2
1
CT3
B
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
SPN-55e INPUTS
B
45
46
47
48
N/C
N/C
49
50
N/C
51
52
N/C
53
54
55
56
57
58
59
60
61
62
N/C
B
I/O PORTS
N/C
N/C
B
N/C
DB-25 CONNECTOR
1
2
DB3
3
DB4
4
DB5
5
7
15
DB15
16
DB16
18
DB18
19
DB19
20
8
9
A
DB14
17
6
DB9
14
10
11
DB12
12
DB13
13
21
DB21
22
DB22
A
23
24
DB24
25
DB25
CALL IN SH
25
CALL IN HI
24
N/C
23
CALL OUT SH
22
CALL OUT HI
21
N/C
20
DIGITAL GND
19
+5V DIGITAL
18
N/C
17
REMOTE OFF
16
"ON" TALLY
15
REMOTE ON
14
13
AUDIO COMMON
12
CALL IN LO
11
N/C
10
N/C
9
CALL OUT LO
8
N/C
7
N/C
6
N/C
5
START/STOP COM.
4
STOP
3
START
2
N/C
1
N/C
A
A
CT1
SPN-55e
CONTRACT NO.
- Sergey Averin -
APPROVALS
DRAWN
SA
CHECKED
SA
ISSUED
SA
W# 700657
2
- Sergey Averin -
DATE
9-18-01
SIZE FSCM NO.
SCALE
APPROVALS
DRAWN
SA
New Bern, NC 28562
DWG. NO.
16S0021x
B
SPN-2000 PCB
SHEET
REV
_
1
2
page 12 - 19
DATE
9-18-01
CHECKED
SA
ISSUED
SA
W# 700657
3 OF 3
R-55e/July 2004
SPN-55e
CONTRACT NO.
SIZE FSCM NO.
New Bern, NC 28562
DWG. NO.
16S0021x
B
SCALE
SPN-2000 PCB
SHEET
REV
_
3 OF 3
1
R-55e/July 2004
page
R-55e / July 2004
SPN-55e Superphone Module - Load Sheet
page 12 – 20
8
7
Right
DB-25
D
6
LINE 1
5
Right
DB-25
HI
HI
SH
SH
LO
LO
4
3
D
N/C
"LINE 5" LT IN SH
HI
HI
"LINE 5" LT IN HI
SH
SH
"LINE 5" RT IN LO
LO
LO
"LINE 5" LT IN LO
"LINE 5" RT IN SH
"LINE 5" RT IN HI
"LINE 6" LT IN SH
"LINE 6" LT IN LO
"LINE 6" LT IN HI
LINE 2
C
Left
DB-25
LINE 5
"LINE" LT OUT HI
SH
SH
"LINE" RT OUT LO
LO
LO
N/C
LINE
5 IN
HI
SH
SH
LO
LO
"LINE" RT OUT SH
"LINE" RT OUT HI
N/C
N/C
N/C
N/C
LINE 6
HI
HI
SH
SH
LO
LO
LINE
6 IN
HI
"LINE" LT OUT LO
N/C
HI
SH
LO
LO
C
N/C
"LINE 1" LT IN SH
"LINE 1" LT IN LO
"LINE 1" LT IN HI
"LINE 1" RT IN SH
"LINE 1" RT IN LO
"LINE 1" RT IN HI
"LINE 2" LT IN SH
"LINE 2" LT IN LO
"LINE 2" LT IN HI
"LINE 2" RT IN HI
"LINE 3" LT IN SH
"LINE 3" LT IN LO
"LINE 3" LT IN HI
"LINE 3" RT IN SH
"LINE 3" RT IN LO
Left
DB-25
"LINE 4" LT IN LO
"LINE 4" LT IN HI
SH
B
"LINE 4" RT IN SH
"LINE 4" RT IN LO
LO
HI
"LINE 3" RT IN HI
"LINE 4" LT IN SH
HI
B
"LINE 2" RT IN SH
"LINE 2" RT IN LO
I/O PORTS
(Right DB-25)
HI
SH
I/O PORTS
(Left DB-25)
"LINE 6" RT IN HI
"LINE" LT OUT SH
HI
LINE 3
LINE
3 IN
"LINE 6" RT IN SH
"LINE 6" RT IN LO
HI
LINE
2 IN
1
LS-55e Line Selector
LINE 4
LINE
4 IN
LINE
1 IN
2
"LINE 4" RT IN HI
LINE
OUT
SH
LO
To Left DB-25 CONNECTOR
Right DB-25 CONNECTOR
IN PHASE
OUT OF PHASE
TYPICAL 4 POLE
SWITCH PINOUT
VIEWED FROM ABOVE
(COMPONENT SIDE)
A
LS-55e
CONTRACT NO.
APPROVALS
DRAWN
SA
DATE
6-6-01
CHECKED
SA
ISSUED
SA
W# 700679
8
R-55e/July 2004
7
6
5
4
LS-55e Line Select Module Schematic - Sheet 1 of 1
3
A
New Bern, NC 28562
SIZE FSCM NO.
SCALE
2
DWG. NO.
D
LS-2600 PCB
16S0025
SHEET
REV
-
1 OF 1
1
page 12 - 21
R-55e / July 2004
LS-55e Line Select Module - Load Sheet
page 12 – 22
8
7
6
5
4
3
2
1
TR-55e I/O
D
D
SW "1"
I/O PORTS
SW "2"
AUDIO COMMON
SW 6 C.
SW 6 N.O.
SW 6 LED -
SW 6 LED +
SW 5 C.
SW 5 N.O.
SW 5 LED -
SW "3"
SW 5 LED +
SW 4 C.
SW 4 N.O.
SW 4 LED -
C
SW 4 LED +
SW 3 C.
SW 3 LED -
SW 3 LED +
SW 2 C.
SW "4"
C
SW 3 N.O.
SW 2 N.O.
SW 2 LED -
SW 2 LED +
SW 1 C.
SW 1 N.O.
SW 1 LED -
SW 1 LED +
SW "5"
SW "6"
B
B
TYPICAL 2 POLE
SWITCH PINOUT
A
TR-55e
CONTRACT NO.
VIEWED FROM ABOVE
(COMPONENT SIDE)
APPROVALS
DRAWN
SA
DATE
1-3-01
CHECKED
SA
ISSUED
SA
W# 700658
8
R-55e/July 2004
7
6
5
4
TR-55e Tape Remote Module Schematic - Sheet 1 of 1
3
A
New Bern, NC 28562
SIZE FSCM NO.
SCALE
2
DWG. NO.
D
TR-2000 PCB
16S0022
SHEET
REV
-
1 OF 1
1
page 12 - 23
R-55e / July 2004
TR-55e Tape Remote Module - Load Sheet
page 12 – 24
8
7
6
5
4
3
2
1
CLOCK
CLOCK: HOURS
D
8
3
CLK_DSPL_DP
CLK_DSPL_G
CLK_DSPL_C
CLK_DSPL_B
CLK_DSPL_A
CLK_DSPL_F
CLK_DSPL_E
CLK_DSPL_D
5
10
9
1
2
4
6
7
COM2
COM1
dp
d
dp
c
e
g
f
e
g
f
b
d
c
a
b
a
DS1
CLOCK: MINUTES
CLK_DSPL_A
CLK_DSPL_B
CLK_DSPL_C
CLK_DSPL_D
CLK_DSPL_E
CLK_DSPL_F
CLK_DSPL_G
CLK_DSPL_DP
7
a
f
g
e
d
a
6
b
4
c
2
d
b
1
e
9
f
10
c
g
5
dp
dp
3
COM1
8
COM2
8
3
CLK_DSPL_DP
CLK_DSPL_G
CLK_DSPL_C
CLK_DSPL_B
CLK_DSPL_A
CLK_DSPL_F
CLK_DSPL_E
CLK_DSPL_D
5
10
9
1
2
4
6
7
COM2
COM1
dp
d
dp
c
e
g
f
e
g
f
b
d
c
a
b
a
DS2
DS3
CLOCK: SECONDS
CLK_DSPL_A
CLK_DSPL_B
CLK_DSPL_C
CLK_DSPL_D
CLK_DSPL_E
CLK_DSPL_F
CLK_DSPL_G
CLK_DSPL_DP
7
a
f
g
e
d
a
6
b
4
c
2
d
b
1
e
9
f
10
c
g
5
dp
dp
3
COM1
8
COM2
8
CLK_DSPL_DP
CLK_DSPL_G
CLK_DSPL_C
CLK_DSPL_B
CLK_DSPL_A
CLK_DSPL_F
CLK_DSPL_E
CLK_DSPL_D
3
5
10
9
1
2
4
6
7
DS4
COM2
COM1
dp
d
dp
c
e
g
f
e
g
f
b
d
c
a
b
a
f
g
e
d
DS5
D
CLK_DSPL_A
CLK_DSPL_B
CLK_DSPL_C
CLK_DSPL_D
CLK_DSPL_E
CLK_DSPL_F
CLK_DSPL_G
CLK_DSPL_DP
7
a
a
6
b
4
c
2
d
b
1
e
9
f
10
c
g
5
dp
dp
3
COM1
8
COM2
DS6
TIMER
TIMER: MINUTES
8
C
3
CLK_DSPL_DP
CLK_DSPL_G
CLK_DSPL_C
CLK_DSPL_B
CLK_DSPL_A
CLK_DSPL_F
CLK_DSPL_E
CLK_DSPL_D
5
10
9
1
2
4
6
7
TIMER: SECONDS
CLK_DSPL_A
CLK_DSPL_B
CLK_DSPL_C
CLK_DSPL_D
CLK_DSPL_E
CLK_DSPL_F
CLK_DSPL_G
CLK_DSPL_DP
7
COM2
COM1
dp
d
dp
c
e
g
f
e
g
f
b
d
c
a
b
a
a
f
g
e
d
DS8
a
6
b
4
c
2
d
b
1
e
9
f
10
g
c
5
dp
dp
3
COM1
8
COM2
8
3
CLK_DSPL_DP
CLK_DSPL_G
CLK_DSPL_C
CLK_DSPL_B
CLK_DSPL_A
CLK_DSPL_F
CLK_DSPL_E
CLK_DSPL_D
5
10
9
1
2
4
6
7
7
COM2
COM1
dp
d
dp
c
e
g
f
e
g
f
b
d
c
a
b
a
DS9
a
f
g
e
d
DS10
VCC
VCC
a
6
b
4
c
2
d
b
1
e
9
f
10
g
c
5
dp
dp
3
COM1
8
COM2
CLK_DSPL_A
CLK_DSPL_B
CLK_DSPL_C
CLK_DSPL_D
CLK_DSPL_E
CLK_DSPL_F
CLK_DSPL_G
CLK_DSPL_DP
C
DS11
VCC
VCC
TO CONSOLE
SW1
VCC
VCC
R81 220
1
3
4
B
R34
SW6
2
AUTO
AUTO_SW
GND
R32 220
VCC
R75
R82
4.99K
88.7K
GND
1
3
4
GND
VCC
3
4
R68
GND
R31 220
VCC
2
3
4
5
6
7
8
9
10
R26 220
R25
R29
4.99K
4.99K
TMR_HOLD
R28 220
R30 220
1
3
4
CT1
4.99K
GND
GND
VCC
GND
SET
VCC
+3.3V
SW3
GND
VCC
R67 220
2
1
3
4
R61
4.99K
1
SW7
+3.3V
+3.3V
R51
R48
R44
10.0K
10.0K
10.0K
10.0K
R42 51
XDATA_CLK
R46 51
XCLK_SYNC
R49 51
XTMR_SYNC
R52 51
GND
332 R87
+3.3V
R53
XDATA
VCC
VCC
DS13
VCC
GND
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
VCC
DS7
B
TO CLD-220 PCB (CLOCK/TIMER DISPLAY)
R27
4.99K
2
START/STOP
1
FROM CONSOLE
R33
SW5
4.99K
R74 220
CT2
R24 220
+DIGin
VCC
GND
VCC
1
4.99K
MODE
SW2
2
R23
4.99K
2
GND
VCC
R41 51
R43 51
R47 51
R50 51
VCC
GND
VCC
GND
20
220 R88
2
RESET
3
4
GND
+REG
VCC
SW4
A
VCC
GND
R79 220
1
3
4
R78
4
HOLD
3
Q9
HOLD_SW
2
RVBAT
4.99K
VCC
VCC
VCC
VCC
VCC
VCC
VCC
SBD D4
R86 220
GND
C32
C3
C28
C35
C2
C18
C20
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
2.2F
C6
C7
1500uF
0.1uF
OUT IN
P4 VC
GND
PQ05D 5
F1
+REG
1
2
C5
C4
330uF
0.1uF
+DIGin
D1
1N4002W
- Sergey Averin -
APPROVALS
DRAWN
GND
GND
GND
GND
GND
GND
GND
CLK-55
CONTRACT NO.
POLYSW
1.0A
GND
SA
DATE
9-20-04
CHECKED
SA
ISSUED
SA
W# 700815
8
R-55e/Sep 2004
7
6
5
4
CLK-55 Clock/Timer Schematic Sheet 1 of 2
3
A
New Bern, NC 28562
SIZE FSCM NO.
SCALE
2
DWG. NO.
D
CLK-55 PCB
16S00xx
SHEET
REV
_
1 OF 2
1
page 12 - 25
7
6
5
4
3
2
+3.3V
VCC
U1
75
CCLK
_________
PROGRAM
51
GND
GND
+3.3V
D
M0
M1
M2
23
SDO
32KHZ_OUT
GND
Z1
FPGA_TDI
TMS
TCK
60_HZ_in
FSIN
1_HZ_in
ESE_IN
27
80
81
79
2
99
3.83K R59 R58 1.00K 39
36
88
91
PROMDATA
HOLD_SW
73
70
69
FSOUT
66
51 R3
60
57
56
FSOSC
53
1HZ_OUT
82
83
84
C
86
33 R62
87
93
33 R65
95
96
1_HZ_out
33 R70
97
1.00K R71
98
3
4
AUTO_SW
5
6
R16
R19
R22
332
332
332
332
VCC
NOT INSTALLED
8
XTMR_SYNC
XCLK_SYNC
XDATA_CLK
17
18
XDATA
19
45
VCC
VCC
GND
GND
GND
VCC
R17 51
R5
R8
R10
R12
332
332
332
332
4
6
CCLK
3
INIT
DONE
8
Q4
FDN340P
54
55
58
62
R2 51
65
R1 51
Q3
FDN340P
R77 33
Q2
FDN340P
CE
SDI
71
72
+3.3V
5
CCLK
43
3
7
INIT
DONE
FSOSC
R39 10.0K
+2.5V
C24
C8
C25
0.1uF
0.1uF
0.1uF
GND
GND
1 HZ IN
+2.5V
R9
R11
1.00K
1.00K
1.00K
1.00K
GND
GND
FSOUT
D3
BAT54
+2.5V
FSIN
R80
0.01uF
10.0K
1
GND
2
1 Hz in
0.01uF
SDO
16
RVBAT
1
DIG.COM
R69
10.0K
GND
GND
+2.5V
+2.5V
+2.5V
+2.5V
C22
C11
C16
C21
C42
0.1uF
0.1uF
0.1uF
0.1uF
150uF
GND
GND
GND
GND
60_HZ_in
1
GND
2
C27
19
DS12
VCC2 VBAT
1HZ_OUT
X1
9
8
32.768kHz
XTAL
3
Y2
32KHZ_OUT
2
VBAT
E2
R83 4.99K
+3.3V
GND
+3.3V
+3.3V
+3.3V
+3.3V
C10
C34
C26
C33
C41
0.1uF
0.1uF
0.1uF
0.1uF
150uF
GND
GND
GND
GND
GND
+3.3V
+3.3V
+3.3V
+3.3V
+3.3V
GND
3V
B
VCC
GND
GND
60 Hz in
DIG.COM
Y1
10.0K
GND
X2
5
18
10 DS1306 11
3V
1
1
2
3
4
5
6
7
2
GND
DONE
VCC
SDO 32KHZ
R60
0.01uF
1 HZ OUT
GND
14
GND SERMODE
E1
GND
GND
3
GND
VBAT
RVBAT
CT5
GND
9
17
U4
VCC VCCIF
____
7
1HZ
INT0
INT1
12
CE
14
X1
SCLK
15
X2
SDI
CE
SCLK
SDI
C29
60 HZ IN
GND
C31
27
25
GND
D3 BAT54
C40 0.01uF
C
42
20
R84
GND
CT3
GND
29
R35 220
VCC
GND
1_HZ_in
GND
PROMDATA
40
CLK_DSPL_DP
R7
CT4
+2.5V
TDO
R57 5.1
XC18V01
TDO
TDI
CLK
CF ____
13
OE/RST
___
15
CE
____
21
CEO
TCK
TMS
31
D0
D1
D2
D3
D4
D5
D6
D7
+3.3V
R4
GND
FPGA_TDI
R56 5.1
TDO
TMS
TDI
TCK
10
1.00K
4.99K
GND
6
7
NOT INSTALLED
CLK_DSPL_G
VCC
Q1
FDN340P
PROMDATA
1
D0
___
CF
CLK
+3.3V
17
U2
TMS
TDI
TCK
CLK_DSPL_F
VCC
67
68
19
TDO
TMS
TDI
TCK
R37
CLK_DSPL_E
VCC
R6 51
59
D
J1
____
OE/RST ____
___
10
13
CE
CEO
VCC
47
5
33pF
1.00K
+3.3V
VCC
4
C13
R21
1.00K
R20 51
3
33pF
R18
1.00K
5
XCF01
43
46
7
VCCJ VCCO
TMR_HOLD
2
C14
R15
1.00K
TMS
TDI
TCK
41
44
5
DS1706
34
1
R40 10.0K
CLK_DSPL_D
32
40
8
U3
20
+3.3V
31
CT7
FSOUT
4
R63
4.99K
30
XC2S30
B
6
GND
R13
GND
22
1.00K
U5
_____ ____
PBRST WDS
___
NMI
__
ST
____
IN
RST
1
PROMDATA
+2.5V
20
21
R36
CLK_DSPL_C
VCC
Q5
FDN340P
16
10.0K
CLK_DSPL_B
VCC
13
15
1.00K
4148 D2
Q6
FDN340P
9
10
R64
GND
CLK_DSPL_A
VCC
Q7
FDN340P
TDO
R55 5.1
+3.3V
R85
J2
Q8
FDN340P
7
PAD134
PAD149,Vref7
PAD152
TDI
PAD161,IRDY
TMS
TCK
PAD164,TRDY
PAD173
GCK0,I
PAD176,Vref6
GCK1,I
PAD191
GCK2,I
PAD194
GCK3,I
PAD197
PAD203,Vref6
D0,DIN,I/O
PAD212
D1,I/O
PAD215
D2,I/O
PAD233,Vref5
D3,I/O
PAD239
D4,I/O
PAD242
D5,I/O
PAD260,Vref5
D6,I/O
PAD280
D7,I/O
PAD289,Vref4
PAD307
PAD12,Vref1
PAD310
PAD18
PAD316,Vref4
PAD21
PAD325
PAD39,Vref1
PAD328
PAD48
PAD347,Vref3
PAD68,Vref0
PAD353
PAD86
PAD362
PAD89
PAD374,Vref3
PAD95,Vref0 PAD386,TRDY
PAD104
PAD389,IRDY
PAD113
PAD401,Vref2
PAD122,Vref7
PAD413
PAD422
PAD128
PAD428,Vref2
PAD131
5.1V
1.00K R66
77
TDO
R14
DONE
49
VCC
VCC
SCLK
74
DONE
___
CS,I/O
______
WRITE,I/O
INIT
52
BUSY,DOUT,I/O
25
R38 4.99K
____
INIT,I/O
VCC
J6
CCLK
VCC
1
J3
8
1_HZ_out
1
GND
2
4
J5
J4
5
6
7
1 Hz out
DIG.COM
14
13
12
11
10
9
8
14
VCC
X1
13
12
1.0M R45
11
C19 220pF
R54
10
40.2K
9
X2
8
14 PIN DIP
SOCKET FOR
32.768 KHZ
OSCILATOR.
VCC
R76
A
+REG
4.99K
ESE_IN
220pF
C30
CT6
Q10
MMBTA05
R72 88.7K
R73
2
40.2K
GND
GND
GND
1
+REG
3
ESE INPUT
C9
C17
C15
C12
C23
C1
C36
SHIELD
GND
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
150uF
0.1uF
IN OUT
GND
1
LT1117
3.3V
+2.5V
Q12
2
3
C37
C38
0.1uF
0.1uF
IN OUT
GND
1
LT1117
2.5V
GND
GND
GND
GND
GND
GND
CLK-55
CONTRACT NO.
2
C39
0.1uF
- Sergey Averin -
APPROVALS
GND
GND
+3.3V
Q11
VCC
GND
DRAWN
SA
DATE
9-20-04
CHECKED
SA
ISSUED
SA
W# 700815
8
R-55e/Sep 2004
7
6
5
4
CLK-55 Clock/Timer Schematic Sheet 2 of 2
3
A
New Bern, NC 28562
SIZE FSCM NO.
SCALE
2
DWG. NO.
D
CLK-55 PCB
16S00xx
SHEET
REV
_
2 OF 2
1
page 12 - 26
SCHEMATIC DRAWINGS
Top
Bottom
Clock/Timer (CLK-55) - Load Sheet
R-55e
R-55e // Sep
July 2004
page
page 12
12––27
3
8
7
6
5
PGMLTACN
PGMRTACN
AGND
D
AUDLTACN
AUDRTACN
AGND
MONOACN
AGND
MXMACN
AGND
AGND
AGND
C
BUSPIN47
+PHin
V+in
V-in
GND
+DIGin
BUSPIN59
BUSPIN61
CT2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
AGND
AGND
AGND
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
PGMRTACN
AGND
AUDLTACN
AUDRTACN
AGND
MONOACN
B
AGND
MXMACN
AGND
AGND
1
4
5
6
7
8
9
10
11
13
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
AGND
BUSPIN47
+PHin
V+in
A
V-in
GND
+DIGin
BUSPIN59
BUSPIN61
46
47
48
49
50
51
52
53
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
BUSPIN59
BUSPIN61
59
60
61
62
+DIGin
BUSPIN60
BUSPIN62
AGND
PGMLTACN
PGMRTACN
AGND
AUDLTACN
AUDRTACN
AGND
MONOACN
AGND
MXMACN
AGND
1
2
AGND
3
4
5
6
7
8
V+in
GND
AGND
BUSPIN48
+PHin
V+in
V-in
GND
+DIGin
BUSPIN60
56
57
58
59
60
61
62
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
BUSPIN48
+PHin
CT4
1
2
3
4
5
6
AGND
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
BUSPIN59
BUSPIN61
59
60
61
62
+DIGin
BUSPIN60
BUSPIN62
AGND
PGMLTACN
PGMRTACN
AGND
AUDLTACN
AUDRTACN
AGND
MONOACN
AGND
MXMACN
AGND
1
2
AGND
3
4
5
6
7
8
AGND
AGND
BUSPIN47
V+in
V-in
GND
AGND
PGMLTACN
PGMRTACN
AGND
AUDLTACN
AUDRTACN
AGND
MONOACN
AGND
MXMACN
AGND
AGND
7
CT5
AGND
AGND
AGND
AGND
AGND
AGND
4
5
6
AGND
AGND
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
BUSPIN59
BUSPIN61
59
60
61
62
+DIGin
BUSPIN60
BUSPIN62
AGND
PGMLTACN
PGMRTACN
AGND
AUDLTACN
AUDRTACN
AGND
MONOACN
AGND
MXMACN
AGND
1
2
AGND
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
AGND
BUSPIN47
V+in
V-in
GND
D
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
BUSPIN48
+PHin
V-in
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
BUSPIN59
BUSPIN61
59
60
61
62
+DIGin
BUSPIN60
BUSPIN62
AGND
PGMLTACN
PGMRTACN
AGND
AUDLTACN
AUDRTACN
AGND
MONOACN
AGND
MXMACN
AGND
1
2
AGND
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
AGND
AGND
AGND
BUSPIN47
AGND
V+in
GND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
BUSPIN48
+PHin
CT7
AGND
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
27
28
29
30
29
30
31
32
31
32
33
34
33
34
35
36
35
36
37
38
37
38
39
40
39
40
41
42
41
42
43
44
43
44
45
46
45
46
47
48
47
48
49
50
49
50
51
52
51
52
53
54
53
54
55
56
55
56
57
58
57
58
BUSPIN59
BUSPIN61
59
60
59
60
61
62
+DIGin
BUSPIN60
BUSPIN62
61
62
AGND
PGMLTACN
PGMRTACN
AGND
AUDLTACN
AUDRTACN
AGND
MONOACN
AGND
MXMACN
AGND
1
2
AGND
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
AGND
AGND
BUSPIN47
V+in
V-in
GND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
BUSPIN48
+PHin
AGND
BUSPIN47
V+in
V-in
GND
BUSPIN59
BUSPIN61
C
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
BUSPIN48
+PHin
V-in
B
+DIGin
BUSPIN60
BUSPIN62
AGND
AGND
AGND
AGND
AGND
AGND
AGND
CT8
AGND
AGND
AGND
AGND
AGND
BUSPIN48
+PHin
V+in
V-in
GND
+DIGin
BUSPIN60
AGND
BUSPIN47
V+in
GND
BUSPIN62
BUSPIN59
BUSPIN61
CT9
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
BUSPIN48
+PHin
AGND
AGND
BUSPIN47
V+in
V-in
GND
+DIGin
BUSPIN60
BUSPIN62
BUSPIN59
BUSPIN61
+DIGin
AGND
+DIGin
+DIGin
7
6
5
4
+DIGin
+DIGin
+DIGin
+DIGin
C14
C13
C11
C12
C16
C15
C10
330uF
0.1uF
1uF
330uF
330uF
0.1uF
1uF
GND
GND
GND
V+in
V+in
V+in
GND
GND
GND
GND
V-in
V-in
V-in
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
BUSPIN48
+PHin
C5
C4
C6
330uF
C9
C7
330uF
0.1uF
0.1uF
C8
0.1uF
0.1uF
AGND
AGND
AGND
+DIGin
BUSPIN60
BUSPIN62
3
AGND
AGND
AGND
+PHin
+PHin
+PHin
C2
C1
10uF
0.1uF
AGND
- Sergey Averin -
DRAWN
SA
C3
AGND
0.1uF
AGND
MBE-55
CONTRACT NO.
APPROVALS
V-in
MBE-55 8 Position Mother Board (Extender) Schematic - Sheet 1 of 1
R55e/Aug 2004
2
3
7
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
BUSPIN48
+PHin
1
CT6
9
BUSPIN62
54
55
AGND
AGND
PGMLTACN
PGMRTACN
AGND
AUDLTACN
AUDRTACN
AGND
MONOACN
AGND
MXMACN
AGND
A
DATE
8-21-04
CHECKED
SA
ISSUED
SA
W# 700812
8
1
AGND
44
45
AGND
16
AGND
14
16
8
14
AGND
BUSPIN47
12
15
7
17
AGND
2
3
6
15
AGND
AGND
5
13
AGND
AGND
4
10
AGND
AGND
3
AGND
12
AGND
AGND
2
11
CT10
PGMLTACN
2
CT3
1
9
AGND
38
39
AGND
PGMLTACN
PGMRTACN
AGND
AUDLTACN
AUDRTACN
AGND
MONOACN
AGND
MXMACN
AGND
AGND
AGND
3
EDGE CONNECTORS BUSS CHART
CT1
AGND
4
New Bern, NC 28562
SIZE FSCM NO.
SCALE
2
DWG. NO.
D
MBE-55 PCB
16S00xx
SHEET
REV
1 OF 1
1
page 12 - 28
SAMPLE
R-55e / Aug 2004
MBE-55 8 Position Mother Board (Extender) - Load Sheet
page 12 – 29
8
7
6
5
4
3
2
1
INPUT/SPN MODULE
CT1
D
C
B
V+in
WP4
V-in
WP5
OUTPUT MODULE
CT2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
2
1
2
3
4
3
4
5
6
5
6
7
8
7
8
9
10
9
10
11
12
11
12
13
14
13
14
15
16
15
16
17
18
17
18
19
20
19
20
21
22
21
22
23
24
23
24
25
26
25
26
27
28
27
28
29
30
29
30
31
32
31
32
33
34
33
34
35
36
35
36
37
38
37
38
39
40
39
40
41
42
41
42
43
44
43
44
45
46
45
46
47
48
47
48
49
50
49
50
51
52
51
52
53
54
53
54
55
56
55
56
57
58
57
58
59
60
59
60
61
62
61
62
CR MODULE
PHANTin
AGND
WP2
WP7
+DIGin
AGND
WP1
WP6
GND
AGND
WP8
AGND
WP9
1
2
3
4
5
6
7
8
9
10
D
TO TIMER/CLOCK
CT11
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
TO VU METERS
C
SC2 MODULE
CT3
WP3
CT12
CT7
1
CT4
1
2
1
2
3
4
3
4
5
6
5
7
8
7
8
9
10
9
10
11
12
11
12
13
14
13
14
15
16
15
16
17
18
17
18
19
20
19
20
21
22
21
22
23
24
23
24
25
26
25
26
27
28
27
28
29
30
29
30
31
32
31
32
33
34
33
34
35
36
35
36
37
38
37
38
39
40
39
40
41
42
41
42
43
44
43
44
45
46
45
46
47
48
47
48
49
50
49
50
51
52
51
52
53
54
53
54
55
56
55
56
57
58
57
58
59
60
59
60
61
62
61
62
6
B
CT8
AGND
1
AGND
2
PHANTin
3
PHANTin
4
5
HDPN1
V+in
6
RT
V-in
7
A
LT
V+in
CT9
LT
1
HDPN2
2
3
RT
CT10
1
2
3
V-in
8
MBR-2000
CONTRACT NO.
AGND
9
- Sergey Averin -
AGND
10
LT
PWR
TO
QMP
CT5
LT
1
SPKR1
2
RT
3
CT6
APPROVALS
1
SPKR2
2
RT
3
DRAWN
SA
DATE
6-23-03
CHECKED
SA
ISSUED
SA
W# 700653
8
7
6
5
4
3
MBR-2000 4 Position Mother Board (Right) Schematic - Sheet 1 of 1
R-55e/July 2004
A
New Bern, NC 28562
SIZE FSCM NO.
SCALE
2
DWG. NO.
D
MBR-2000B PCB
16S0010
SHEET
REV
B
1 OF 1
1
page 12 - 30
SCHEMATIC DRAWINGS
MBR-2000 4 Position Mother Board (Right) - Load Sheet
R-55e / July 2004
page 12
12––31
4
page
8
7
6
5
4
3
2
1
INPUT/SPN MODULE
CT5
AGND
D
PGMLTACN
PGMRTACN
AGND
AUDLTACN
AUDRTACN
AGND
MONOACN
AGND
MXMACN
AGND
AGND
C
AGND
BUSPIN47
+PHin
V+in
V-in
GND
+DIGin
BUSPIN59
BUSPIN61
B
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
V+in
WP4
V-in
WP5
AGND
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
AGND
PGMLTACN
PGMRTACN
AGND
AUDLTACN
AUDRTACN
AGND
MONOACN
AGND
MXMACN
AGND
AGND
AGND
AGND
AGND
AGND
22
23
61
AGND
AGND
AGND
AGND
BUSPIN47
AGND
V+in
AGND
AGND
GND
AGND
BUSPIN59
BUSPIN61
AGND
BUSPIN60
BUSPIN62
62
WP3
+PHin
GND
AGND
WP8
AGND
WP9
PGMLTMONITOR
PGMRTMONITOR
AUDLTMONITOR
AUDRTMONITOR
MONOMONITOR
MXMMONITOR
AGND
CUESPKR1
V+in
GND
HDPNGND1
HDPNLT1
V+in
A
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
BUSPIN48
+PHin
AGND
PGMVULT
SWTVULT
V+in
V-in
GND
+DIGin
BUSPIN60
BUSPIN62
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
AGND
GND
AGND
GND
+DIGin
AGND
+DIGin
AGND
CT1
CT18
1
1
2
2
4
5
6
7
8
9
10
D
HOLD
START_STOP
+Dreturn
GND
TO TIMER/CLOCK
AGND
CT21
AGND
PGMLTMONITOR
PGMRTMONITOR
AUDLTMONITOR
AUDRTMONITOR
MONOMONITOR
MXMMONITOR
PGMVURT
SWTVURT
+DIGin
AGND
+DIGin
AGND
+DIGin
AGND
+DIGin
V-in
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
SWTVURT
GND
SWTVULT
GND
PGMVURT
GND
PGMVULT
GND
TO VU METERS
+DIGin
START_STOP
HOLD
C
3
3
4
4
5
5
6
6
7
7
8
8
PWR IN
9
+DIGin
+DIGin
+DIGin
+DIGin
+DIGin
+DIGin
C16
C17
C14
C18
C19
C20
330uF
0.1uF
1uF
330uF
330uF
0.1uF
GND
GND
GND
V+in
V+in
V+in
GND
C15
1uF
GND
GND
GND
V-in
V-in
V-in
CT12
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
AGND
CRS_4
CRS_6
AGND
CRS_10
CRS_12
AGND
CRS_16
AGND
CRS_20
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
SPKRGND1
AGND
CRS_3
CRS_5
AGND
CRS_9
CRS_11
AGND
CRS_15
AGND
CRS_19
AGND
CUEMONITOR
TBMONITOR
AGND
PGMLTMONITOR
PGMRTMONITOR
AUDLTMONITOR
AUDRTMONITOR
MONOMONITOR
MXMMONITOR
AGND
CUESPKR2
V+in
V-in
GND
+DIGin
HDPNGND1
HDPNRT1
HDPNGND2
HDPNLT2
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
AGND
CRS_4
CRS_6
AGND
CRS_10
CRS_12
AGND
CRS_16
AGND
CRS_20
AGND
AGND
AGND
AGND
C9
C8
C10
330uF
C11
C13
330uF
0.1uF
0.1uF
C12
0.1uF
0.1uF
AGND
AGND
AGND
AGND
AGND
AGND
+PHin
+PHin
+PHin
C7
C6
10uF
0.1uF
AGND
C5
0.1uF
AGND
AGND
B
AGND
AGND
AGND
AGND
AGND
AGND
AGND
SPKRGND2
V-in
+DIGin
HDPNGND2
HDPNRT2
AGND
+PHin
CT19
+PHin
V+in
V+in
V-in
V-in
V+in
LT
V-in
C2
C3
0.1uF
0.1uF
AGND
AGND
+DIGin
+PHin
HDPN1
RT
1
2
3
CT20
HDPNLT1
LT
HDPNGND1
HDPN2
RT
HDPNRT1
1
2
3
HDPNLT2
HDPNGND2
HDPNRT2
MBR-55
CONTRACT NO.
AGND
- Sergey Averin -
AGND
PWR
TO
QMP
CT15
C1
C4
0.1uF
0.1uF
GND
AGND
LT
SPKR1
RT
1
2
3
CT16
CUESPKR1
LT
CUESPKR1
SPKR2
RT
SPKRGND1
1
2
3
CUESPKR2
CUESPKR2
SPKRGND2
APPROVALS
DRAWN
SA
7
6
5
4
3
A
DATE
9-23-04
CHECKED
SA
ISSUED
SA
W# 700813
R-55e/Sep 2004
2
3
AGND
10
8
1
AGND
SC2 MODULE
CT11
AGND
CRS_3
CRS_5
AGND
CRS_9
CRS_11
AGND
CRS_15
AGND
CRS_19
AGND
CUEMONITOR
TBMONITOR
AGND
+DIGin
WP6
V-in
7
V-in
GND
WP1
AGND
6
AGND
PGMLTACN
PGMRTACN
AGND
AUDLTACN
AUDRTACN
AGND
MONOACN
AGND
MXMACN
AGND
CR/SC MODULE
V+in
AGND
+DIGin
5
AGND
+DIGin
+PHin
+DIGin
GND
4
AGND
AGND
+DIGin
2
3
BUSPIN48
WP7
GND
CT22
CT17
1
AGND
WP2
+PHin
OUTPUT MODULE
CT10
New Bern, NC 28562
SIZE FSCM NO.
SCALE
2
DWG. NO.
D
MBR-55 PCB
16S0010
SHEET
REV
_
1 OF 2
1
page 12 - 32
8
7
6
5
4
3
2
1
AGND
PGMLTACN
PGMRTACN
AGND
AUDLTACN
AUDRTACN
AGND
MONOACN
AGND
MXMACN
AGND
D
AGND
AGND
BUSPIN47
V+in
GND
C
BUSPIN59
BUSPIN61
AGND
PGMLTACN
PGMRTACN
AGND
AUDLTACN
AUDRTACN
AGND
MONOACN
AGND
MXMACN
AGND
AGND
B
AGND
BUSPIN47
V+in
GND
BUSPIN59
BUSPIN61
+DIGin
+DIGin
GND
AGND
A
GND
V-in
AGND
+PHin
V+in
INPUT MODULE
INPUT MODULE
CT6
CT7
1
2
3
4
5
AGND
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
BUSPIN48
+PHin
AGND
PGMLTACN
PGMRTACN
AGND
AUDLTACN
AUDRTACN
AGND
MONOACN
AGND
MXMACN
AGND
AGND
AGND
BUSPIN47
V+in
V-in
GND
+DIGin
BUSPIN60
BUSPIN62
BUSPIN59
BUSPIN61
CT13
1
2
3
4
5
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
INPUT MODULE
CT8
CT9
2
3
4
5
AGND
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
CT3
CT4
1
1
2
2
3
3
4
4
5
5
6
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
BUSPIN48
+PHin
7
8
8
9
9
AUX PWR
AUX PWR
AGND
AGND
BUSPIN47
V+in
V-in
GND
+DIGin
BUSPIN60
BUSPIN62
BUSPIN59
BUSPIN61
AGND
R-55e/Sep 2004
7
6
2
3
4
5
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
BUSPIN48
+PHin
AGND
V+in
V-in
GND
+DIGin
BUSPIN60
BUSPIN62
AGND
D
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
+PHin
V-in
+DIGin
C
LINE SELECT/ TAPE REMOTE
CT14
1
2
3
4
5
AGND
AGND
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
1
2
3
4
5
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
AGND
BUSPIN48
+PHin
AGND
V+in
V-in
GND
+DIGin
BUSPIN60
BUSPIN62
AGND
+DIGin
+PHin
GND
AGND
GND
V+QMP
V-QMP
AGND
V-in
2
AGND
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
AGND
AGND
AGND
AGND
AGND
AGND
AGND
B
AGND
AGND
AGND
AGND
AGND
AGND
AGND
+PHin
V-in
+DIGin
3
4
5
6
7
8
9
10
AGND
+PHin
V+QMP
V-QMP
AGND
PWR TO QMP
AGND
+PHin
1
F2
V+in
POLYSW
.4A
F1
V+in
V-in
MBR-55
CONTRACT NO.
- Sergey Averin -
V+QMP
APPROVALS
DRAWN
V-QMP
POLYSW
.4A
SA
5
4
3
A
DATE
9-23-04
CHECKED
SA
ISSUED
SA
W# 700813
8
1
CT2
+DIGin
6
7
AGND
PGMLTACN
PGMRTACN
AGND
AUDLTACN
AUDRTACN
AGND
MONOACN
AGND
MXMACN
AGND
AGND
6
7
INPUT MODULE
1
LINE SELECT/ TAPE REMOTE
New Bern, NC 28562
SIZE FSCM NO.
SCALE
2
DWG. NO.
D
MBR-55 PCB
16S0010
SHEET
REV
_
2 OF 2
1
page 12 - 33
SAMPLE
R-55e / Sep 2004
MBR-55 10 Position Mother Board (Right) - Load Sheet
page 12 – 34
R-55e/July 2004
page 12 - 35
SCHEMATIC DRAWINGS
LED-3 Meter LED Lamp - Load Sheet
R-55e / July 2004
page 12
12––36
5
page
8
7
6
5
4
3
D1 UF4007
2
1
INSTALL TWO
R70 24
R72 24
A2
3
C61
2.43K R53
R52 2.43K
SNB
GNDP
INSTALL ONE
R61 88.7K
R62 88.7K
GNDP
DRN
A1
1
2
18
5
17
~V16P
2.2nF
R50 3.32K
220uF
C14
220uF
A2
3
R59 10
K
2
A1
1
3
C39
C33
C27
22uF
330uF
330uF
C41
C35
C29
22uF
330uF
330uF
L1
4.7uH
L3
4.7uH
MBR-4060P
270uF
D10 4148
R54 2.00K
R55 2.00K
TP4
U3 1
SYNC VCC
D
C51
R63
0.001uF
1.00K
FB
4
S
FSCQ1265
2
14
10
13
9
12
R57 10.0K
C55
C54
C59
C53
R56 10.0K
22uF
22uF
2.2nF
330uF
NOT
INSTALLED
K
2
A1
1
~V28A
~V14A
8
11
~V16N
C42
C36
C30
22uF
330uF
330uF
L4
4.7uH
MUR3020
A2
3
K
2
A1
1
10uF
C20
C10
R66
330uF
22uF
220
C22
C12
R68
330uF
22uF
56
C23
C13
R69
330uF
22uF
56
DV8P1
D6
~V8N
220uF
DV16N
C40
C34
C28
22uF
330uF
330uF
4.7uH
L2
C21
C11
220
330uF
22uF
R67
+36V
+36V
+16V
+16V
+8V
+8V
+8V
+8V
GND
GND
-16V
-16V
D
D4
C47
V1
GNDP
Z6
1SMB5919
5.6V
2.2nF
C
UF4007 D13
PWM
RT1 SG55
Z250LA40
250V
3
5
0.001uF C52
SS14 D9
28VD
NOT
INSTALLED
C65
270uF
A2
3
NOT
INSTALLED
C62
1.0M
28VR
R64
C56
28VC
BR2
D7
KBL08
0.47uF
6
C9
DV8P2
D5
16
R58 10
C19
DV16P
D3
~V8P
UF4007 D11
220uF
POLYSW
0.16A
MBR-4060P
C60
R51 2.43K
TP1
R60 88.7K
FER
16VCC
GNDP
K
2
~V36P
D8 4148
TP2
R65 11K
UF4007 D14
19
4
100nF
10uF
C26
NOT
INSTALLED
D12
MB3510
C63
C32
NOT
INSTALLED
MUR3020
20
C38
NOT
INSTALLED
~V48P
T2
1
0.47uF
F3
DV36P
R71 24
Z1
1N5364
51V
TP3
+BR
R73 24
NOT
INSTALLED
D
NOT
INSTALLED
INSTALL ONE
D2 UF4007
C
1.0M
GND
Z4
1SMB5919
5.6V
PR2
0.47uF
0.1uF
4.7nF
CGND
5 U2
Z5
1SMB5919
5.6V
CGND
Z2
1SMB5919
5.6V
C57
0.22uF
L5
10mH
Y
L5
Y
10mH
Z3
1SMB5919
5.6V
C58
R46 1.00K
C37
C44
4.7nF
C43
PR1
GNDP
CT5
CNY17
4
+8V
1
6
C50
R45
R44
0.01uF
1.30K
26.7K
2
R43 40.2K
R48 53.6K
PRch12
0.47uF
C31
R41
0.0047uF
R39
-
3
+
NOT
INSTALLED
Pwr ON
LED
KA431
1.0M
C25
0.0047uF
2
GREEN
2.5V
1
4.99K
C24
DS1
+16V
3
U1
2
R42
4.99K
C46
C45
1uF
1uF
NOT
INSTALLED
CT4
F4
CR1 1 2
+8V
POLYSW
1.0A
1K 3
GND
Y
R47 220
+8V
GNDP
PRch11
1
R49 220
GND
C48 0.1uF
NOT
INSTALLED
R40
C49 4.7nF
CGND
GND
Y
C64
330uF
1
+
2
-
3
Fan
B
FUSE
2.0A
PRf2
F2
FUSE
2.0A
F1
PRf1
B
NOT
INSTALLED
WP3
CT3
WP2
1
GND
2
GND
3
+8V
4
+8V
5
GND
6
-16V
7
T1
1
16
15
85-265 VAC
50-60Hz
INPUT
~V36P
2
DRN
~V28A
~V14A
A
GNDP
3
14
~V16P
13
~V8P
12
GND
8
11
7
10
6
9
T1
~V48P
14b
FOR ETD-34 TRANSFORMER
+BR
FOR ETD-39
TRANSFORMER
3
CT2
2
1
3
WP1
2
1
CT1
CGND
+36V
13b
12b
~V36P
~V16P
8
+16V
11b
10b
9b
8b
~V8N
~V48P
~V8P
GND
C8
C7
C6
C5
C4
C3
C2
C1
0.01uF
0.01uF
0.01uF
0.01uF
0.01uF
0.01uF
0.01uF
0.01uF
CGND
~V8N
CGND
CGND
CGND
CGND
CGND
CGND
~V16N
SPS-100
CONTRACT NO.
~V16N
- SA UR US - Sergey Averin -
APPROVALS
1-5-09
CHECKED
SA/MM
SA
W# 700915
8
7
6
5
4
3
A
DATE
DRAWN SA/WWP
ISSUED
R-55e / Jan 2009
CGND
Output
New Bern, NC 28562
SIZE FSCM NO.
SCALE
2
DWG. NO.
D
SPS-100B PCB
00S0041
SHEET
REV
B
1 OF 1
1
page 12 - 37
R-55e / Jan 2009
SPS-100 Power Supply Load Sheet
page 12 – 38

R-55E Owner`s Manual

Transcription

Similar documents

DON`T TO THAT D - American Snowmobiler Magazine

Permalife Full Catalog