Assembly COSHH - Carrs of Sheffield Health and Safety Information

ADHESIVES DIVISION
Product Data Sheet
National Starch & Chemical Ltd
Wexham Road
Slough
Berkshire SL2 5DS
Tel: (0)1753 533494, Fax: (0)1753 501241
134-217A
Supplied by Interlock Adhesives Ltd
0900/CD/02
Description
Appearance
Formulated hot melt adhesive
Yellow coloured solid.
Technical Characteristics
Typical Data
Viscosity (Brookfield
Thermosel Sp 27)
8,100 mPa.s. at 140°C, speed 10 rpm
4,600 mPa.s. at 160°C, speed 20 rpm
2,700 mPa.s. at 180°C, speed 50 rpm
Typical Properties
Molten Tack
:
Very high
Open Time
:
Long
Setting speed
:
Slow
F & DA Status
The ingredients of 134-217A comply with the requirements of FDA 176.170 subject to extractive limits
of the regulation.
134-217A /0900/CD/02
The information given and the recommendations made herein are based on our experience and are believed to be accurate. No guarantee as to, or responsibility for, their accuracy can be
given or accepted and no statement made herein is to be treated as a representation or warranty. In every case we urge and r ecommend that purchasers before using any product make their
own tests to determine, to their own satisfaction, its suitability for their particular purposes under their own operating conditions. Such as evaluation should be repeated if materials are changed
in any way or bought from a different source. No agent or representative of our has any authority to vary, omit or otherwise alter these terms.
Features
Benefits
*
Versatile adhesion.
*
Bonds a wide range of low energy surfaces,
polyethylene, “Metpol” etc..
*
Good heat and cold resistance.
*
Suitable for a wide range of ambient
conditions.
*
Used for chilled applications on difficult
surfaces.
*
Good cohesive strength.
*
Strong bonds to many surfaces.
Application Guide
Suitable for wheel and jet applicators.
Application temperature : 155 to 175°C.
Typically
155°C tank 160°C tank
160°C hose 165°C tank
165°C wheel 170°C gun
Packaging
Consult local sales office.
Storage & Handling
Rotate stock using oldest material first.
Keep containers upright and closed to prevent contamination.
Do not mix with other adhesives.
Store under ambient conditions preferably below 30°C and above 10°C to avoid water condensation.
Shelf life : Minimum 1 year under recommended conditions.
HEALTH & SAFETY
Users should familiarise themselves with the safety data sheet before using or
handling this product.
The information given and the recommendations made herein are based on our experience and are believed to be accurate. No guarantee as to, or responsibility for, their accuracy can be
given or accepted and no statement made herein is to be treated as a representation or warranty. In every case we urge and r ecommend that purchasers before using any product make their
own tests to determine, to their own satisfaction, its suitability for their particular purposes under their own operating conditions. Such as evaluation should be repeated if materials are changed
in any way or bought from a different source. No agent or representative of our has any authority to vary, omit or otherwise alter these terms.
*** SAFETY DATA SHEET ***
1. CHEMICAL PRODUCT AND COMPANY IDENTIFICATION
PRODUCT NAME
SUPPLIER Interlock Adhesives
2. COMPOSITION/INFORMATION ON INGREDIENTS
CHEMICAL FAMILY Hot Melt Adhesive
COMPONENT CAS NUMBER CONCENTRATION EEC SYMBOL
RISK PHRASES No components which pose a risk.
3. HAZARDS IDENTIFICATION
EMERGENCY OVERVIEW
Not classified as dangerous.
EYE As supplied: irritant as a foreign body. As used: severe thermal hazard.
SKIN CONTACT As supplied: no hazard. As used: severe thermal hazard.
INHALATION Vapors and/or aerosols which may be formed at elevated temperatures may
be irritating to eyes and respiratory tract.
INGESTION Low oral toxicity.
4. FIRST-AID MEASURES
EYE If hot: flush with cool water. Treat as a wax or resin burn. Do not attempt to
remove solidified adhesive. Get medical attention immediately.
As supplied: remove as foreign body.
SKIN CONTACT If hot: flush with cool water. Treat as wax or resin burn. Do not attempt to
remove solidified adhesive. Get medical attention immediately.
As supplied:Non-hazardous.
INHALATION Remove to fresh air. Get medical attention if irritation persists.
INGESTION None required.
5. FIRE-FIGHTING MEASURES
EXTINGUISHING MEDIA CO2; Dry Chemical
SPECIAL FIREFIGHTING PROCEDURES
No special procedures are required.
FIRE & EXPLOSION HAZARDS Non-combustible.
HAZARDOUS COMBUSTION PRODUCTS
Carbon monoxide, carbon dioxide, unknown hydrocarbons.
FLASH POINT > 250 °C
6. ACCIDENTAL RELEASE MEASURES
SPILL AND LEAK PROCEDURES
Allow to cool and solidify. Scrape up and collect in suitable containers for disposal.
For safety and environmental precautions, please review entire Safety Data Sheet for necessary information.
7. HANDLING AND STORAGE
HANDLING/STORAGE Store in a cool, dry area. Precaution: this product should only be heated to
recommended temperatures. The hazards of pyrolysis products are unknown.
SENSITIVE TO STATIC ELECTRICITY No
SPECIAL SENSITIVITY No special sensitivity.
8. EXPOSURE CONTROLS/PERSONAL PROTECTION
VENTILATION REQUIREMENTS
Local exhaust over glue chamber.
EYE PROTECTION REQUIREMENTS
Safety glasses, goggles or face shield to protect against splashing.
GLOVE REQUIREMENTS Thermally resistant gloves should be worn.
CLOTHING REQUIREMENTS Uniforms, coveralls, or a lab coat should be worn.
RESPIRATORY REQUIREMENTS
None required if good ventilation is maintained.
9. PHYSICAL AND CHEMICAL PROPERTIES
PURE SUBSTANCE OR PREPARATION Preparation.
PHYSICAL FORM Solid
COLOUR amber
ODOUR No odour.
BOILING POINT > 250 °C
MELTING/FREEZING POINT 90 - 100 °C
SOLUBILITY IN WATER Insoluble; Water.
RELATIVE DENSITY 1.000
FLASH POINT > 250 °C
10. STABILITY AND REACTIVITY
STABILITY Stable Not applicable.
The information given and the recommendations made herein are based on our experience and are believed to be accurate. No guarantee as to, or responsibility for, their accuracy can be
given or accepted and no statement made herein is to be treated as a representation or warranty. In every case we urge and r ecommend that purchasers before using any product make their
own tests to determine, to their own satisfaction, its suitability for their particular purposes under their own operating conditions. Such as evaluation should be repeated if materials are changed
in any way or bought from a different source. No agent or representative of our has any authority to vary, omit or otherwise alter these terms.
11. TOXICOLOGICAL INFORMATION
EYE As supplied: irritant as a foreign body. As used: severe thermal hazard.
SKIN As supplied: no hazard. As used: severe thermal hazard.
INHALATION Vapors and/or aerosols which may be formed at elevated temperatures may
be irritating to eyes and respiratory tract.
INGESTION Low oral toxicity.
CHRONIC (LONG TERM) EFFECTS OF EXPOSURE
EFFECTS OF CHRONIC EXPOSURE
Although this product has not been tested for chronic effects it is judged as
having a low order of toxicity based on component information. Use of good
industrial hygiene practices is recommended.
TARGET ORGANS None known.
SKIN SENSITIZATION No.
POSSIBLE BIRTH DEFECT HAZARD No.
CARCINOGEN No.
PRODUCT INFORMATION Not established.
12. ECOLOGICAL INFORMATION
POTENTIAL EFFECT ON ENVIRONMENT Unknown.
MOBILITY Unknown.
PERSISTENCE AND DEGRADABILITY Unknown.
POTENTIAL TO BIOACCUMULATE No
ECOTOXICITY Unknown.
13. DISPOSAL CONSIDERATIONS
WASTE DISPOSAL METHODS Waste disposal should be in accordance with existing Community,National and local
regulations.
EMPTY CONTAINER WARNINGS Not needed.
14. TRANSPORT INFORMATION (See also section 9)
IATA CLASSIFICATION Not classified as dangerous.
IMDG CLASSIFICATION Not classified as dangerous.
ADR/RID Not classified as dangerous.
15. REGULATORY INFORMATION
Not classified as dangerous.
EINECS All components of this product are listed in EINECS or ELINCS.
Directives 88/379/EEC and 91/155/EEC have been considered when compiling this SDS; the information is provided for
health and safety assessment by an industrial user. Reference should be made to any relevant local or national health, safety,
and environmental legislation. This information does not constitute indication of suitability for specific uses.
16. OTHER INFORMATION
MSDS DATE 02-March-2013
FOR REGULATORY INFORMATION, CONTACT:
A.G. Bingham
Divisional Product Assurance Manager
Interlock Adhesives Limited
The information given and the recommendations made herein are based on our experience and are believed to be accurate. No guarantee as to, or responsibility for, their accuracy can be
given or accepted and no statement made herein is to be treated as a representation or warranty. In every case we urge and r ecommend that purchasers before using any product make their
own tests to determine, to their own satisfaction, its suitability for their particular purposes under their own operating conditions. Such as evaluation should be repeated if materials are changed
in any way or bought from a different source. No agent or representative of our has any authority to vary, omit or otherwise alter these terms.