Document 6480153

Transcription

Document 6480153
SUMMARY OF BASIS FOR APPROVAL
1.0 GENERAL INFORMATION
Licensed Product Name:
Albumin (Human) 5% and 25%
Name and Address of Sponsor:
Octapharma Pharmazeutika
Produktionsges. m. b. H.
Oberlaaer Strasse 235
A - 1100 Vienna, Austria
Biologics License Application
(BLA) Tracking Number:
STN: 12515410
2.0 INDICATIONS FOR USE
Restoration and maintenance of circulating blood volume where volume deficiency has
been demonstrated, and use of a colloid is appropriate.
The choice of albumin rather than artificial colloid will depend on the clinical situation of
the individual patient.
3.0 DOSAGE AND ROUTE OF ADMINISTRATION
~ l b u m i n(Human) 5% is a soIution for intravenous infusion, supplied in the dosage
strength of 50 g human albumidL. The following pack sizes are supplied: 100 mL. (5 g),
250 mL (12.5 g) and 500 mL. (25 g).
Albumin (Human) 25% is a solution for intravenous inhsion, supplied in the dosage
strength of 250 g human albumidL. The followingpack sizes are supplied: 50 mL
(12.5 g) and 100 d (25 g).
Albumin (Human) contains protein, of which 2 96% is albumin. The preparation is
N - a c e t y l - D L - t r y p t o p h a n and caprylic acid
L and the
a
r
e present in a range of 0.064-0.096 mmollg protein in the final container.
The so1ution.contains 130-160mmol sodium per liter and the potassium content does not
exceed 2 mmol per liter. The concentration of the albumin preparation, dosage and the
ifision-rate should be adjusted to the patient's individual requirements.
The dose required depends on the size of the patient, the severity of trauma or illness and
on continuing fluid and protein losses. Measures of adequacy of circulating volume and
not plasma albumin levels should be used to determine the dose required.
If human albumin is to be administered,hemodynamic monitoring should be preformed
regularly; this may include:
arterial blood pressure and pulse rate
central venous pressure
pulmonary artery occlusion pressure
Octapharma Albumin (Human) S%and 25%
BLA STN BL 12515410
Summary Basis of Approval
urine output
electrolytes
hematocrithemoglobin
4.0 MANUFACTURING, CHEMISTRY, AND CONTROLS:
Overview of Manufacturing Process
Albumin (Human) is a sterile, liquid preparation of albumin derived from large pools of
human plasma. All units of plasma used in the manufacture of Albumin (Human) are
provided by FDA-approved blood establishmentsonly.
The product is manufactured by the Cohn-Oncley cold ethanol fractionation process
followed by ultra- and dia-filtration. The manufacturing process includes heat treatment
of bulk as well as in final containers at +60 3t 0.5OC for 10-11 hours. The sterile bulk
solution is aseptically filled into sterile, pyrogen-free glass bottles. The bottles are closed
with rubber stoppers and sealed with crimp-caps. Each vial is subject to visual inspection
prior to labelling and packaging.
The viral safety of the finished product is achieved through a combination of process
steps including Cohn fractionation (Precipitation of ~ractionI+II+III, Precipitation of
Fraction IV, Precipitation of Fraction V) and final container pasteurization.
Validationof Assays Usedfor Albumin (Human) - Final ContainerProduct
The quantitative assays to characterizethe final product were performed according to the
requirements of the USP and CFR respectively, or if not described there methods from
other Pharmacopoeias were applied, e.g. the European Pharmacopoeia (EP). The scope
for validations is given in the ICH guidelines. International standards (WHO) were used
for calibration whenever available.
The followina test methods on final containerproduct were validated for the
determination of specified quality attributes:
Summary Basis of Approval
Octapharma Albumin (Human) 5% and 25%
BLA STN BL 125154/0
Validation of Manufacturing
The
on of the Albumin (Human) manufacturing process was camed out in
and
ritical process parameters and acceptance criteria were defined based
results from previous validation studies and extensive experience with the production
process.
Based on the results, reproducibility of the manufacturing process through to the fmal
product could be demonstrated with consistent quality. In-process controls and final
container test results obtained from these validation batches have been evaluated. All
results are consistent and within the established limits.
Validation of Viral Safety
The Albumin (Human) manufacturing process includes a number of different steps which
can clear viruses that may be present in the starting plasma and thereby ensure the viral
safety of the finished product. The capacity of these steps to clear viruses has been
validated with a panel of both relevant and model viruses. With respect to enveloped
viruses, viral clearance is achieved by fmal container pasteurization with additional
clearance by Cohn fractionation. Non-enveloped viruses are primarily removed by Cohn
fractionation, but the final container pasteurization also contributes to the overall
clearance.
Table 1.Viral reduction factors during Albumin (Human) 5% manufacturing
Production steps
Viral reduction factor [loglo]
Enveloped viruses
Non-enveloped viruses
PRV
SBV
HIV-1
RE0 3
PPV
HAV
Cohn
Precipitation of
fractionation* Fraction IV
> 5.50
> 6.02
> 7.08
> 7.84
6.29
> 7.45
Pasteurization final container
> 8.07
> 8.67
> 7.89
6.53
3.69
4.67
Global reduction factor
> 13.57
> 14.69
> 14.97
> 14.37
9.98
> 12.12
* Due to the similar mode of action of the individual process steps only precipitation of
Fraction IV was used to calculate the global reduction factor.
Summary Basis of Approval
Octaphaxma Albumin (Human) 5% and 25%
BLA STN BL 12515410
Table 2. Viral reduction factors during Albumin (Human) 25% manufacturing
In vitro reduction factor [loglJ
Production steps
Non-enveloped viruses
Enveloped viruses
PRV
SBV
HIV-1
RE0 3
PPV
HAV
Cohn
Precipitation of
fractionation* Fraction IV
> 5.50
> 6.02
> 7.08
> 7.84
6.29
> 7.45
Pasteurization final container
> 8.67
> 8.'79
> 7.23
5.36
3.22
2.45
Global reduction factor
> 14.17
> 14.81
> 14.31
> 13.20
9.51
> 9.90
* Due to the similar mode of action of the individual process steps only precipitation of
Fraction IV was used to calculate the global reduction factor.
PRV: Pseudorabies Virus
SBV: Sindbis Virus
HIV- 1: Human Immunodeficiency Virus - 1
Reo 3: Reovirus Type 3
PPV: Porcine Parvovirus
HAV: Hepatitis A Virus
Stability Studies of Final Container Product
Stability data for the final container of Albumin (Human) 5% comprising 24 months'
data were submitted. A design for a full stability study was complied according
filling sizes of 100 mL and 250 mL.&$qbatches have been put on
f each filling size. All vials fiom thep batches are stored in inverted
orientation. and for com~arison.vials of one batch of each filling size are stored uurieht
.. .
:
,~
$ 1band accelerakd &:
at
C. iong-term
study conditions were applied as well.
Mm:,
'&,&&:
.:&.
Real-time data fiom the long-term studies show that all parameters remain constant up to
24 months. Furthermore, the orientation of the vials, inverted or upright, has no impact on
the stability of the product.
Statistical evaluation by linear regression of
indicates that a shelf-life of 36 months can be expected when stored at + 2°C to + 25"C,
as the confidence limit does not intersect the specification limit within this time.
Stability data for final containers of Albumin (Human) 25% comprising 36 months data
of long term studies at jmc and
months data of accelerated studies
the product for both filling sizes of 50 mL and 100 mL was proven for each storage
condition mentioned above.
Octaphama Albumin (Human) 5% and 25%
BLA STN BL 125 15410
Summary Basis of Approval
In addition, conformance lots have been put on stability. For Albumin (Human) 5%
months and for Albumin (Human) 2 5 % m months of data were presented to the FDA.
This study is still ongoing and results will be submitted to the FDA on a regular basis.
A shelf life of 36 months can be guaranteed if the product is stored at + 2OC to +25"C. It
is recommended to store the product protected from light.
ShelfLife and Storage Conditions of Final Container Produci
On the basis of stability data provided for the final product, the approved shelf life is 36
months if stored at +2OC to +25OC (36°F to 77OF) and protected from light. Protection
from light is ensured by the outer carton.
The date of manufacture is defined as the date of final sterile filtration of the formulated
drug product.
Labeling
Labeling of Albumin (Human) 5% and Albumin (Human) 25% consists of a package
insert, vial labels and carton labels.
The outer carton label and the vial label state the name of drug, NDC code, strength,
route of administration, prescription status, composition, storage conditions, expiry date,
lot number, manufacturer ,,mddistributor.
Pre-Licensing Inspection of Octapharma Pharmazeutika Produktionsges. m.b.h
The pre-licensing inspection at the manufacturing site of Octapharma Phannazeutika
Produktionsgesellschaft m.b.H. in Vienna, Austria was carried out by the Agency from
March 22 to 3 1,2006. The observations presented in the Form 483 were resolved. 'The
response information package was submitted to CBER on April 19,2006. No further
comments or questions have been raised by the Agency; thus the manufacture of
Albumin (Human) complies with information given in the Biologics License Application.
5.
NON-CLINICAL PHARMACOLOGY AND TOXICOLOGY:
Since Albumin (Human) is a native albumin, which is a normal constituent of human
plasma to be used at physiological levels, the standard pharmacodynarnic and toxicity
studies generally carried out for new substances are not applicable to this product.
Octapharma Albumin (Human) 5% and 25%
BLA STN BL 12515410
6.
Summary Basis of Approval
HUMAN PHARMACOKINETICS
Albumin makes up half the normal intravascular protein mass and is responsible for 75%80% of the plasma colloid osmotic pressure.
In a healthy person, 9- 12 grams of albumin are synthesized in the liver per day. The rate
of synthesis is controlled primarily by changes in the colloid osmotic pressure and the
osmolality of the extravascular space. Insulin, thyroxin, and corticosteroids also stimulate
the production of albumin. However, growth hormone has no significant effect on
albumin synthesis. Importantly, in severe protein malnutrition, production of albumin
may be decreased.
Albumin is a predominantly extravascular protein with a total mass of approximately 160
grams, despite a lower interstitial concentration compared with serum concentration. The
serum concentration of albumin is about 4 gramsldl in normal.individuals and the total
intravascular mass is about 120 grams. Under normal circumstances, the albumin
concentration in the interstitial space is half that in the intravascular space. The half-life
of albumin is 17-19 days.
The catabolism of albumin takes place mainly in the vascular endothelium at a rate of 912 grams per day, or 4% of total body albumin. The rate of albumin degradation is reIated
to its concentration. Calorie and protein deprivation also accelerate albumin catabolism.
Serum levels of albumin may fall during periods of stress, trauma, or sepsis despite its
long half-life. The drop may result from accelerated redistribution from the intravascular
space, decreased synthesis, and increased catabolism. Injury and infection result in a
decrease of serum albumin level of approximately 1- 1.5 grams/& within 3-7 days.
Clearance of proteins from the interstitium is dependent upon the lymphatic flow, which
in heaIthy individuals is around 120 rnL/h, with a protein content of about 80% of
plasma. The flow of lymph itself is dependent upon interstitial fluid pressure, intrinsic
pumping by the lymphatic vessels and external compression of vesseIs by muscle
contraction, arterial pulsation, and body movement.
The distribution of exogenous albumin between body compartments has been examined
by the injection of radio-labeled albumin. Over the first 2 days, there is a rapid phase of
disappearance from the plasma that correlates with the transcapillary exchange rate of
4.5% per hour. The distribution half-time is about 15 hours. Then there is a slower decay
of about 3.7% per day with an elimination half time ofabout 19 days.
7.
CLINICAL MICROBIOLOGY
There is no clinical microbiology evaluation for Albumin (Human) 5% and Albumin
(Human) 25% as it is not an anti-infective product.
Octapharma Albumin (Human) 5% and 25%
BLA STN BL 12515410
8.
Summary Basis of Approval
CLINICAL SUMMARY
In order to obtain a marketing authorisation for Albumin (Human) 25% in the US,
Octapharma conducted a clinical trial under an IND. The purpose of this study was to
demonstrate that the efficacy of Albumin (Human) 25% is non-inferior to another human
albumin brand (25%) licensed in the US in preventing central volume depletion after
paracentesis due to cirrhotic ascites and has a comparable safety profile.
Cohort A received treatment with albumin after consecutive paracenteses (multiple dose
treatment), whereas cohort B received treatment with albumin after single paracentesis
(single dose treatment). Efficacy evaluation was performed only in cohort A. Planned
enrolment was 50 subjects in Cohort A and 20 subjects in cohort B.
Due to the fact that the SAFE Study had resolved prior safety concerns with human
albumin raised by the Cochrane Group in 1998, and the extensive post-marketing safety
experience with Octapharma's albumin preparations, the study was terminated
prematurely after enrollment of 17 subjects in agreement with the FDA.
Efficacy
The efficacy evaluation of efficacy was based on changes from baseline of Blood Urea
Nitrogen (BUN) and serum creatinine at Day I in cohort A.
The changes from baseline for BUN and serum creatinine at Day 1, following the first
paracentesis, were analysed with the baseline observation and the volume of ascites
.removed as covariates, and with treatment, centre and cohort as factors. These efficacy
variables were assessed for the first paracentesis only. Non-inferiority was not formally
tested. No clinically relevant differences were noted between the two treatment groups
with respect to changes in BUN and creatinine levels from baseline to post-treatment. No
clinically relevant changes in body weight were noted between the two treatment groups.
Due to the reduced power, no efficacy conclusions can be made. However, even though only 17 patients were available for analysis, no difference from a descriptive point of view was observed between the two treatment groups. Safety
A total of 8 subjects in the Albumin (Human) treatment group experienced at least one adverse event (AE). The most frequently reported individual AEs were urinary tract infection, abdominal discomfort, and nausea. The majority of adverse events were mild or moderate in severity and were not considered related to study treatment. A total of 7 subjects (4 subjects in the Albumin (Human) treatment group and 3 subjects in the control group) experienced at least one serious AE. Octapharma Albumin (Human)5% and 25%
BLA STN BL 12515410
Summary Basis of Approval
Many subjects had abnormal laboratory measurements at various points throughout the
course of the study. However, the overwhelming majority of these abnormal
measurements were considered by the Investigator to be not clinically significant.
No clinically significant mean changes were noted for any vital signs parameter
following study treatment. Minor fluctuations were noted in mean systolic and diastolic
blood pressures. There was no indication that Albumin (Human) treatment had an
orthostatic effect on blood pressure following study treatment after any paracentesis.
No clinically relevant differences were observed between the two treatment groups with
respect to safety and tolerability.
9.
ORPHAN DRUG CONSIDERATION
There is no orphan drug designation for Albumin (Human) 5% and Albumin (Human)
25%.
10. MARKETING HISTORY
Marketing Authorization in European Union was granted in 1990. Presently Albumin
(Human) is licensed in 55 countries. Since 1992, the total amount sold world-wide of
human albumin manufactured by Octapharma (any concentration) is approximately
(status May 2006).
.