Self-propelled hovercraft Materials:

Transcription

Self-propelled hovercraft Materials:
Self-propelled
hovercraft
Materials:
Styrofoam Meat Tray [20S]
1.5v DC Motor
Plastic Propeller (3-Blade, 3.25”dia) or similar
AAA Cell Battery Holder (For 2 Batteries)
[2] AAA Batteries
[2] 8” Lead Wires (Red/Black)
[1] 8.5 x 11 Cardstock Sheet
Adhesives: Double-Sided Tape, White Glue, Masking Tape
Utility/X-Acto Knife
Build time:
1 Hour
Model adapted from “Fifteen Minute, Self-Propelled Hovercraft,” posted by “Dr. No,” July 30, 2006, on www.instructables.com
Step 1: Make the Intake
The science:
• As the propeller displaces the air that it’s moving through, the intake
redirects that air below the tray, creating the air cushion that makes
the craft hover.
• The intake also supports the motor.
Build it:
We’ve attached a pattern for the intake — see following page.
1 Print the pattern onto 8.5 x 11 cardstock.
2 Using an X-Acto knife (or similar), cut out the intake:
Cut along all solid gray lines and the four magenta lines.
Fold along all blue dotted lines.
3 Place a strip of adhesive — double-stick tape — on the “Adhesive” tabs,
and attach the tabs to the underside of the intake’s back panel. Make
sure to line up the Adhesive tabs’ blue dotted lines with the edge of the
back panel. Once everything is lined up correctly, the back panel will
incline down at 45 degrees, and the side panels will be at 90-degree
angles to the top of the intake.
To fit standard 20S styrofoam meat tray
INTAKE CUT-OUT
Cut Along Solid Gray Lines
Cut Through Magenta Lines
Fold Along Blue Dotted Lines
ve
Ad
h
es
iv
e
si
he
Ad
Back Edge of Intake
DECK CUT-OUT
Adhesive
A
Front
Adhesive
Back Edge of Intake
CUT OUT AND
REMOVE THIS AREA
A
Adhesive
Step 2: Make the Deck
Build it:
We’ve attached a pattern for the deck — see preceding page.
1 Using an utility/X-Acto knife, cut out the deck.
2 Cut out and remove the light gray square in the center of the deck.
3 Using double-sided tape, attach the deck to the bottom of the
styrofoam tray.
4 Using a utility/X-Acto knife, cut out and remove the styrofoam square
below the opening in the deck.
Step 3: Attach the Intake
Build it:
1 Apply double-sided tape/white glue to the deck inside all areas labeled
either “Adhesive” or “A.”
2 Carefully align the 1/2-inch intake flaps with the corresponding
markings on the deck pattern and apply.
! The two triangle folds in front of the intake must be parallel to the
opening as shown below.
Step 4: Motor/Prop Assembly
Build it:
1 Attach the propeller to the motor shaft (wrap it in tape if it’s too narrow).
You may also fill the hole in the propeller with hot glue, allow the hot glue
to cure, and drill a new hole that matches the diameter of the shaft.
2 Center the motor and propeller on top of the intake. The propeller
should be as close to the intake’s opening (without touching the opening)
as possible.
3 Secure the motor across the intake with masking or other tape.
Step 5: Wire the Batteries
Build it:
1 Wire the battery holder to the motor. Attach the positive lead (+) to the
(+) side of the motor. Similarly, wire the negative lead (-) to the (-) side.
! DC Motors spin in either direction, depending on how the leads are
connected. If you plan to solder the connections, first make sure that,
when the propeller turns, air is flowing into the intake.
2 Attach the battery holder to the deck with masking or other tape. Do this
lightly. The performance of the hovercraft depends on having even weight
distribution. You may want to relocate your battery holder to balance the
craft after testing.
Step 6: Test
The science:
Hovercrafts are also known as Air Cushion Vehicles (ACVs). ACVs work
because of “lift.”
Attaining lift begins by forcing air into the intake and under the hovercraft
where it is trapped by a skirt. When enough air is trapped under the craft,
the pressure forces the vehicle off the ground. Once the hovercraft is off
the ground, a small amount of air escapes continuously from beneath the
skirt, and the vehicle “floats” on this cushion of air.
TestinG:
Turn on the batteries and...you’re off!
! If the hovercraft seems to drag along one edge, try repositioning your
battery pack to balance the weight of the vehicle.
! If the hovercraft turns dramatically, try repositioning the motor by
turning it slightly away from the turn.
Hovercraft Airflow Map
Air pulled through the propeller and INTO the intake a
escapes under the hovercraft, creating a cushion of air.
The hovercraft floats on this cushion of air.
Air pulled through the propeller and PAST the intake
moves the hovercraft forward.