Document 6484960

Transcription

Document 6484960
Drywall Primer: A paint material specifically formulated to fill the pores
and equalize the suction difference between gypsum board surface
paper and the compound used on finished joints, angles, fastener heads,
and accessories and over skim coatings. See "comments" section of this
document.
Skim Coat: A thin coat of joint compound, or a material manufactured
especially for this purpose, applied over the entire surface to fill imperfections in the joint work, smooth the paper texture, and provide a uniform
surface for decorating. Excess compound is immediately sheared off,
leaving a film of skim coating compound completely covering the paper.
Matrix Edition:
Recommended Levels
of Gypsum Board Finish
GA–214–M–97
Introduction
In 1988, as a means of resolving a common problem, four major trade
associations concerned with the manufacture, erection, finish, and decoration of gypsum board wall and ceiling systems developed an industrywide, Recommended Levels of Gypsum Board Finish. The document
was intended to assist specification writers, architects, contractors, and
building owners to more precisely describe the finish of walls and ceilings prior to the application of paints and other finishes, to encourage
competitive bidding of suitably finished surfaces, and to enhance the appearance of the final decorative treatment and thereby enlist a satisfied
client. The original document was updated and revised in 1996.
This document takes the section of the 1996 document that discusses the
specific criteria required to achieve individual levels of finish and presents
them in a non-text format. The information contained in the document is
technically identical to the original; however, it is formatted, solely for appearance purposes, into a matrix or grid simply to improve its readability. The scope, terminology, comments and resources sections are reproduced in their entirety from the original document.
Scope. This document describes various levels of finish of gypsum board
surfaces prior to the application of specific types of final decoration. The
recommended level of finish of gypsum board wall and ceiling surfaces
varies with the final decoration to be applied and can also be dependent
on their location in a structure and the type of illumination striking the surface. Each recommended level of finish is described with typical applications.
Terminology. The following definitions are applicable to this document.
Accessories: Metal or plastic beads, trim, or moulding used to protect or
conceal corners, edges, or abutments of the gypsum board construction.
Critical Lighting: Strong sidelighting from windows or surface-mounted light
fixtures. syn severe lighting. See "comments" section of this document.
Joint Photographing: The shadowing of the finished joint areas through
the surface decoration. syn telegraphing.
Spotting: To cover fastener heads with joint compound.
Texture: A decorative treatment of gypsum board surfaces.
Texturing: Regular or irregular patterns typically produced by applying a
mixture of joint compound and water, or proprietary texture materials
including latex base texture paint, to a gypsum board surface previously
coated with drywall primer. See "comments" section of this document.
Comments. Critical (Severe) Lighting Areas. Wall and ceiling areas
abutting window mullions or skylights, long hallways, or atriums with
large surface areas flooded with artificial and/or natural lighting are a
few examples of critical lighting areas. Strong sidelighting from windows
or surface-mounted light fixtures may reveal even minor surface imperfections. Light striking the surface obliquely, at a very slight angle, greatly
exaggerates surface irregularities. If critical lighting cannot be avoided,
the effects can be minimized by skim coating the gypsum board surface,
by decorating the surface with medium to heavy textures, or by the use of
draperies and blinds which soften shadows. In general: gloss, semi-gloss,
and enamel finishes highlight surface defects; textures hide minor
imperfections.
Manufacturer Recommendations. The recommendations of individual
manufacturers of gypsum board, joint tapes and compounds, accessories, drywall primers, wallcoverings, adhesives, texture materials, and
paints may vary from what is recommended herein and as such are not a
part of this recommended specification.
Drywall Primer. Applied as a first coat to the entire prepared gypsum
board surface with brush, roller, or spray prior to decoration. Where
final appearance is critical, the application of high quality, high solids,
drywall primer will minimize most decorating problems.
For finish paints: A good quality, white, latex drywall primer formulated
with higher binder solids, applied undiluted, is typically specified for new
gypsum board surfaces prior to the application of texture materials and
gloss, semi-gloss, and flat latex wall paints.
An alkali and moisture-resistant primer and a tinted enamel undercoat
may be required under enamel paints. Consult with the finish paint manufacturer for specific recommendations.
For wallcoverings: White, self-sizing, water base, "universal" (all-purpose) wallcovering primers have recently been introduced into the marketplace for use on new gypsum board surfaces. These products are
claimed to minimize damage if wallcoverings are subsequently removed,
bind poor latex paint, allow hanging over glossy surfaces and existing
vinyls, hide wall colors, and to be water washable.
Texturing. Texture material is applied by brush, roller, spray, or trowel,
or a combination of these tools, depending on the desired result. Textured wall surfaces are normally overpainted with the desired finish;
overpainting of textured ceiling surfaces may not be deemed necessary
where an adequate amount of material is applied to provide sufficient
hiding properties. A drywall primer may not be required under certain
proprietary texture materials; consult with the manufacturer of the texture materials for specific recommendations.
Tool Marks and Ridges. A smooth surface may be achieved by lightly
sanding or wiping joint compound with a dampened sponge. Care shall
be exercised to ensure that the nap of the gypsum board facing paper is
not raised during sanding operations. For additional information on the
finishing of gypsum board surfaces consult ASTM Standard C 840.
Resources: Designers and specifiers are encouraged to consult the following reference documents:
ASTM C 840, Standard Specification for Application and Finishing of
Gypsum Board. American Society far Testing and Materials, West Conshohocken, PA.
GA-216, Specifications for the Application and Finishing of Gypsum
Board, 1996. Gypsum Association, Washington, D.C.
GA-505, Gypsum Board Terminology, 1991. Gypsum Association,
Washington, D.C.
Master Painters Glossary, Painting and Decorating Contractors of
America, Fairfax, VA.
Contact one of the following associations for additional assistance or
copies of this recommended specification:
The Association of the Wall and Ceiling Industries—International
803 West Broad Street, Suite 600
Falls Church, Virginia 22046
Telephone: (703) 534-8300
http://www.awci.org
Ceilings & Interior Systems Construction Association
1500 Lincoln Highway, Suite 202
St. Charles, Illinois 60174
Telephone: (630) 584-1919
http://www.cisca.org
Gypsum Association
810 First Street NE, #510
Washington, DC 20002
Telephone: (202) 289-5440
Painting and Decorating Contractors of America
3913 Old Lee Highway, Suite 33B
Fairfax, Virginia 22030
Telephone: (703) 359-0826
http://www.pdca.com
Notice
All of the statements, opinions, specifications, and recommendations on levels of
gypsum board finish contained in this publication are for general information purposes
only and are not intended to imply that these are the only materials, procedures, processes, or methods which are available or suitable.
By publishing this document, the co-sponsoring trade associations, and their member companies, individually or collectively, make no express or implied warranty or other representation as to the quality, characteristics, or suitability of the materials or techniques described herein, and specifically disclaim any implied warranties of merchantability or
fitness for a particular purpose which may arise by operation of law or otherwise.