Flex Face Assembly Instructions Part 1

Transcription

Flex Face Assembly Instructions Part 1
I
Stand aril / Hinged & Retro-Fit
Frame Systems
For All Vdtir Fi&miMm FiM;a
c
PCS
'/S
EC-Flex System
EC-Flex Face System - Components:
Standard Frame
Bleed
!
13/16'
- Standard Trim
Cover
23/4'
EC-Flex Retro Fit Sstem
Hinged Frame
35/16'
2"
- Standard Trim
Cover
2' - Standard Trim
Cover
23/4'
Standard Trim Cover
EC-Flex Clip
Bleed Trim Covers
Flex Frame Brace
Retro-Fit Frame Brace
EG-Flex Face Manual Information
EC-Flex System - Fabric Size Requirements
On the Standard and Hinged frame system:
• Add 3" of face material to each dimension or
6" total to the length and width of the cabinet.
• Subtract 1/8" per 3' of face material not to exceed 1"
from either dimension for tension factor.
EC-Retro Fit Frame:
•
•
Add 2 1/2" of face material to each dimension or
5" total to the length and width of the cabinet.
Subtract 1 /8" per 3' of face material not to exceed 1"
from either dimension.
EC-F!ex Clip Placement
First notch a 3" square from each corner of trimmed flex face material. With the face material
facing up, fold approximately 2 1/2" of material over the 4" aluminum bar. Slide and center clip
over face material and bar, bolt side up. Clip spacing should not exceed 10" on center around the
perimeter of the tensioning system. At the start of each corner, place a clip 3-4" from the end for
best results.
EC-Flex System - Bracing Requirements:
Vertical bracing should be used once the face size is larger than 4" tall and 8' long. The ECFrame or Retro-Fit Brace should be used at a maximum of 3' on center. Horizontal bracing may
be required on 4' centers for larger hinged faces. Vertical and horizontal struts should be welded
or double bolted to the frame braces. Size and wall thickness of the vertical struts should be
determined based on cabinet size and structural needs.
Strut's on 4'
Centers
Strut's on 3'
Centers
EC-Flex Face Manual Information
EC-Flex System - Bracing Requirements
EC-Flex Frame Brace is
used when hinging our flex
face hinged system or on
the Retro-Fit frame when
the angle iron frame is
larger than 1 1/2". Vertical
and horizontal bracing may
be required based on the
size of the cabinet.
Note:
The EC-Retro Flex Brace
is used with the EC-Retro
Frame system when
vertical and horizontal
bracing is required.
The vertical struts used with our frame braces should
be sized based on the length of the strut.
Length
To 36"
To 48"
To 68"
To 72"
To 96"
To 1 20"
Square Tube / Wall
3/4" x .125 Wall
1"x.125Wal!
1 1/4"x. 125 Wall
1 1/2"x. 125 Wall
2" x . 125 Wall
2" x . 188 Wall
EC-Flex Face Clip Placements
First notch a 3" square from each corner of trimmed flex face material. With the face material
facing up, fold approximately 2 1/2" of material over the 4" aluminum bar. Slide and center the
clip over face material and bar, side up. Clip spacing should not exceed 10" on center around the
perimeter of the tensioning system. At the start of each corner, place a clip 3-4" from the end for
best results.
Trim Line
31
_
'
|
i
-Face Size
4^
i
i
A
_-
.......
- Clips on 10" Maximum Centers
g1
^
&
w ..— -<
_. .;;,.
-n
r
3"
3"
I
i
I
I
'
l
!
i
_
1
i
4
i
1
!
i
3"