RF Wall Mounted Touch Panel SR-2830B-AC/SR-2830B-DC

RF Wall Mounted Touch Panel
SR-2830B-AC/SR-2830B-DC
Wiring diagram
1)Sender Connection Diagram
110V-230VAC
N
SR-2830B-AC
Feature
SR-2830B-DC
PRI:
Uin=100-240VAC
Iin=15mA MAX
PRI:
Uin=12-24VDC
Iin=0.2A MAX
Out=RF Signal
Out=RF Signal
L
L
N
Power Supply
12-24VDC
GND Vin
L
110V-230VAC
N
Backlight
Glass interface(White & Black)
SR-2830B-AC
Touch sensitive
Adjust brightness & color temperature
SR-2830B-DC
2)Receiver Connection Diagram for Single Unit
N
N
Power Supply
12-36VDC
110V-230VAC
110V-230VAC
■ Sender
2
3
white
4
WW LED Strip
WW LED Strip
CW LED Strip
CW LED Strip
WW LED Strip
Item NO. :SR-2830B-AC/SR-2830B-DC
Input voltage:100V-240VAC/12-24VDC
Output:RF signal(434MHz/868MHz)
LED CONTROLLER
4
Learning Key
3
LED CONTROLLER
white
Parameter
SR-1009FA
2
SR-1009FA
Learning Key
1
1
L
L
Power Supply
12-36VDC
2x10A
CW LED Strip
4x5A
3)Receiver Connection Diagram for Multiple Units
■ Corresponding Receiver
N
1009FA: 12-36VDC input,4 channels x 5A, constant voltage, 4 channels x (60-180)W
Power Supply
12-36VDC
L
1009FA3:12-36VDC input,4 channels x 350mA, constant current, 4 channels x (4.2-12.6)W
110V-230VAC
1009FA7:12-36VDC input,4 channels x 700mA, constant current, 4 channels x (8.4-25.2)W
Note:
One receiver can work with 1-8pcs SR-2830B
One SR-2830B control multiple receivers
The power supply chosen must be 20% higher than
the actual load
86.0
1
LED CONTROLLER
white
Learning Key
WW LED Strip
2
SR-1009FA
CW LED Strip
WW LED Strip
4
Product Size
3
1009EA: 12-36VDC input,4 channels x 8A, constant voltage, 4 channels x (96-288)W
CW LED Strip
1
2
LED CONTROLLER
white
Learning Key
WW LED Strip
CW LED Strip
WW LED Strip
4
SR-1009FA
3
4x5A
CW LED Strip
4x5A
1
2
LED CONTROLLER
white
Learning Key
WW LED Strip
CW LED Strip
3
SR-1009FA
WW LED Strip
4
29.1
86.0
4x5A
CW LED Strip
Note:
Installation
This controller is RF signal to receivers, no need cable.
AC version no need driver, working directly at electric supply 100-240VAC.
The DC version need a driver 12/24V.
1
Po 2-2
w 4V
er D
Su C
pp
l
y
Attention
1) The product shall be installed with qualified person
2) IP20.Please avoid the sun and rain. When installed outdoors, please
ensure it is mounted in a water proof enclosure.
3) Always be sure to mount this unit in an area with proper ventilation to avoid overheating.
SR-2830B-AC
4) Please check if the output voltage of any LED power supplies used comply with the working
voltage of the product.
SR-2830B-DC
Description of buttons
5) Never connect any cables while power is on and always assure correct connections to avoid
short circuits before switching on.
Turn ON/OFF
6) Please ensure that the cable is secured tightly in the connector
7) For updated information please consult your supplier.
Brightness/Kelvin control exchange,
blue under brightness control mode,
Yellow under Kelvin control mode.
Save color into S1/S2.
Warranty Agreement
4 zones, control
seperately or
syhchronously,
each zone could
control multiple
receivers.
1) We provide lifelong technical assistance with this product:
3-year warranty. We print produce date on every products, for example :1125 means
year 2011,week 25.The warranty is for free repair or replacement and covers
manufacturing faults only.
For faults beyond the 3-year warranty we reserve the right to charge for time and parts.
2) Limited Warranty
Operation
1. Switch
Touch on/off button, all zones on/off，Blue when playing. Yellow when off.
Once turn on, the default setting is under brightness control mode
Touch zone button Z1/Z2/Z3/Z4 separately over 2 seconds, which will turn ON/OFF separately.
The backlight blue is ON for the zone, yellow is OFF for the zone.
2. Learning ID with SR-1009 series
Re: Click learning button on RF receiver (SR-1009)→
Short Touch a zone button Z1 or Z2 (sender SR-2830B)→Touch color slider
The light flicker means ID learnt successfully.
3. Save and recall
Save: Touch color slider to get a color→
Hold any button of S1 or S2 over 2 seconds under 4 zones work together
The light flick means successfully saved.
Recall: Short touch button S1 or S2 →Recall the color saved.
Any defects caused by wrong operation.
Any damages caused by unauthorized removal, maintenance, modifying, incorrect
connection and replacement of chips.
Any damages due to transportation, vibration etc. after purchase.
Any damages caused by earthquake, fire, lightning, pollution and abnormal voltage.
Any damages caused by negligence, inappropriate storing at high temperatures and
humidity or near harmful chemicals.
3) Repair or replacement as provided under this warranty is the exclusive remedy to the customer.