service manual 14a1-ru 14a2-ru

Transcription

service manual 14a1-ru 14a2-ru
14A1-RU
14A2-RU
SERVICE MANUAL
SX0M114A1-RU/
COLOUR TELEVISION
Chassis No. UA-1
14A1-RU
14A2-RU
1-2
(14A1-RU)
(14A2-RU)
MODELS
In the interests of user-safety (Required by safety regulations in some countries) the set should be restored
to its original condition and only parts identical to those specified should be used.
FEATURE
Ë
Ë
Ë
Ë
Ë
Ë
Ë
Ë
Ë
Ë
Ë
Ë
Ë
Multi 18 Systems
Full Auto Channel Preset and Auto Channel Skip
100-CH Program Memory
High Contrast Picture
Black Stretch Circuit
CATV (Hyper Band) Ready < Used Frequency Synthesizer
Tuner>
AVL (Sound Keeper) Function
Hotel Mode
On Timer / Sleep Timer / Reminder Timer
Colour Comb Filter Function (NTSC only)
Blue Back Noise Mute
Rear AV-In/Out Terminals and Front AV-In
English and Russian OSD
Page
» SPECIFICATIONS .............................. 2
» IMPORTANT SERVICE NOTES ......... 2
» ADJUSTMENT PRECAUTIONS ......... 3
» TROUBLE SHOOTING TABLE ......... 19
» HOTEL MODE APPLICATION .......... 21
» SOLID STATE DEVICE BASE
DIAGRAM ......................................... 22
» WAVEFORMS ................................... 23
» CHASSIS LAYOUT ........................... 24
» DESCRIPTION OF SCHEMATIC DIAGRAM ............................................... 26
Page
» SCHEMATIC DIAGRAM
■ CRT Unit ....................................... 27
■ MAIN Unit ..................................... 28
» BLOCK DIAGRAM ............................ 32
» PRINTED WIRING BOARD ASSEMBLIES ................................................ 37
» REPLACEMENT PARTS LIST
■ ELECTRICAL PARTS ................... 42
■ MISCELLANEOUS PARTS ........... 46
■ SUPPLIED ACCESSORIES ......... 46
■ PACKING PARTS ......................... 46
■ CABINET PARTS .......................... 46
1-1
CONTENTS
WARNING
The chassis in this receiver is partially hot. Use an isolation transformer between the line cord plug and power
receptacle, when servicing this chassis. To prevent electric shock, do not remove cover. No user – serviceable
parts inside. Refer servicing to qualified service personnel.
SHARP CORPORATION
1
2
2-1
Specifications are subject to change without prior notice.
Cabinet Material .................................................................................... All Plastics
Dimensions
14A1-RU ................................................................................... Width: 357.0mm
Height: 361.0mm
Depth: 368.7mm
Weight (approx.): 9.2 kg
14A2-RU ................................................................................... Width: 446.0mm
Height: 333.0mm
Depth: 365.0mm
Weight (approx.): 9.4 kg
Aerial Input Impedance
VHF/UHF .......................................................................... 75 ohms Unbalanced
Receiving System ..................................................... PAL B/G, D/K, I / SECAM
NTSC 3.58/4.43 MHz (AV)
Tuner Ranges
• VHF-Channels ..................................... E1 (48.25MHz) thru E12 (224.25MHz)
C1 (49.75MHz) thru C12 (216.25MHz)
S1 (105.25MHz) thru S41 (463.25MHz)
• UHF-Channels ................................. E21 (471.25MHz) thru E69 (855.25MHz)
C13 (471.25MHz) thru C57 (863.25MHz)
Speaker
Size
14A1-RU ....................................................................... 5 x 9 cm Elliptic (1 pc)
14A2-RU .................................................................... 5 x 9 cm Elliptic (2 pcs.)
Voice Coil Impedance ........................................................... 16 ohms at 400 Hz
Audio Power Output Rating
14A1-RU ......................................................................................... 3.0W (at Max.)
14A2-RU ......................................................................................... 5.0W (at Max.)
Power Input ..................................................................... 110 ~ 240V AC 50/60 Hz
Power Consumption
14A1-RU .................................................................................................. 65W
14A2-RU .................................................................................................. 68W
Maintenance and repair of this receiver should be done by qualified
service personnel only.
Sweep Deflection ..................................................................................... Magnetic
Intermediate Frequencies
Picture IF Carrier .................................................................................. 38.9MHz
Sound IF Carrier Frequency
5.5MHz ............................................................................................. 33.4MHz
6.0MHz ............................................................................................ .32.9MHz
6.5MHz ............................................................................................. 32.4MHz
Colour Sub-Carrier Frequency ........................................................... 34.47MHz
Picture tube in this receiver employs integral implosion protection.
Replace with tube of the same type number for continued safety.
Do not lift picture tube by the neck.
Handle the picture tube only when wearing shatterproof goggles and after discharging
the high voltage completely.
2-2
1. Inspect all lead dress to make certain that leads are not pinched or that hardware is not
lodged between the chassis and other metal parts in the receiver.
2. Inspect all protective devices such as non-metallic control knobs, insulating fishpapers,
cabinet backs, adjustment and compartment covers or shields, isolation resistor- capacity networks, mechanical insulators etc.
Before returning the receiver to the user, perform the following safety Checks.
BEFORE RETURNING THE RECEIVER
1. When repairing the circuit, be sure not to increase the high voltage to more than 23.5kV(at
beam 0.1 µA) for the set.
2. To keep the set in a normal opeartion , be sure to make it function on 22.0kV ±1.5kV(at
beam 800 µA) in the case of the set. The set has been factory - Adjusted to the abovementioned high voltage.
* If there is a possibility that the high voltage fluctuates as a result of the repairs, never
forget to check for such high voltage after the work.
3. Do not substitute a picture tube with unauthorizerd types and/or brands which may
cause excess X-ray radiation.
This receiver is designed so that any X-Ray radiation is kept to an absolute
Minimum. Since certain malfunctions or servicing may produce potentially
hazardous radiation with prolonged exposure at close range, the followin
precautions should be observed:
X-RAY
1.
2.
3.
4.
When servicing the high voltage system, remove static charge from it by
connecting a 10K ohm Resistor in series with an insulated wire(such as a
test probe) between picture tube dag and 2nd anode lead. (AC line cord
should be disconnected from AC outlet.)
SERVICE OF HIGH VOLTAGE SYSTEM AND PICTURE TUBE
IMPORTANT SERVICE NOTES
Convergence ................................................................. Self Convergence System
Focus ............................................................ Electrostatic Focus High Bi-Potential
SPECIFICATIONS
14A1-RU
14A2-RU
3
3-1
3. For reference please check with memory map
(UA1 Series type RH-IX3368CE Attachment)
Precaution: If haven't done this initiation, it may possibly generate excessive Beam current.
Note: Once the chassis has been assembly together and ready to be POWER ON for the FIRST TIME,
make sure to short JA122 & JA124 to switch to the service mode position first and then turn on the
main power switch (See 2-(1) above).
3. Make sure the data need modify or not (Initial data).
2. The initial data are preset as listed in page 5 & 6.
1. Short JA 122 & JA 124 for 1 second and release to switch to the service mode position and turn on the
main power switch.Initial values are automatically preset, only when a new EEPROM is used (Judge
with the first 4 bytes ).
2. Factory Presetting.
5. Short JA 122 & JA 124 for 1 second and release to switch to the normal mode (OFF) position, and the
microprocessor is in out of the service mode.
4. Using the VOLUME UP/ DOWN key on the remote controller, the data can be modified.
3. Press the CH DOWN / UP key on the remote controller to select the modes reversibly one by one.
2. Press the CH DOWN / UP key on the remote controller to get ready to select the mode one by one.
1. Short JA 122 & JA 124 for 1 second and release to switch to the service mode position, and the
microprocessor is in input mode. (Adjustment through the I2C bus control). (Use JWS Key to set as
well).
1. Setting the service mode by the microprocessor.
This model's setting are adjusted in two different ways: through the I2C bus control and in the conventional
analog manner. The adjustments via the I2C bus control include preset-only items and variable data.
ADJUSTMENT PRECAUTIONS
3-2
↓
W,P RED STD. W.T. (DRI-RS)
↓
W.P. GREEN STD. W.T.(DRI-GS)
↓
W.P.BLUE STD. W.T. (DRI-BS)
↓
W.P. RED COOL W.T.(DRI-RC)
↓
W.P. GREEN COOL W.T.(DRI-GC)
↓
W.P. BLUE COOL W.T. (DRI-BC)
↓
W.P. RED WARM W.T.(DRI-RW)
↓
W.P. GREEN WARM W.T.(DRI-GW)
↓
W.P. BLUE WARM W.T.(DRI-BW)
↓
AGC TAKE OVER POINT (AGC)
↓
VERTICAL SLOPE (V-LIN)
↓
VERTICAL AMP (V-AMP)
↓
VERTICAL SHIFT (V-CENT)
↓
HORIZONTAL SHIFT (H-CENT)
↓
S-CORRECTION (S-COR)
FORWARD : CH DOWN KEY
REVERSE : CH UP
KEY
*(
) means OSD display.
WHITE POINT
ADJ.
MODE
IC
OPTION
MODE
WHITE POINT
ADJ.
MODE
AGC &
GEOMETRIC
MODE
MISC.
OPTION
MODE
AGC &
GEOMETRIC
MODE
(1) In the Service Mode, Key is used to select the mode in the following order.
SERVICE MODE
↓
MAX VOLUME (SUB-VOL)
↓
SUB CONTRAST (SUB-CON)
↓
SUB COLOUR (SUB-COL)
↓
SUB BRIGHTNESS (SUB-BRI)
↓
SUB TINT (SUB-TINT)
↓
SUB SHARPNESS (SUB-SHP)
↓
MAX HOTEL VOLUME (HTL-VOL)
↓
HOTEL PROGRAM NO(HTL-PRG)
↓
OSD GRB REFERENCE (RGB)
↓
BLACK LEVEL OFFSET R(CUT-R)
↓
BLACK LEVEL OFFSET G(CUT-G)
↓
CATHODE DRIVE LEVEL(CDL)
SUB
ADJ.
MODE
FORWARD : CH DOWN KEY
REVERSE : CH UP
KEY
OFFSET
ADJ.
MODE
Y-DELAY
ADJ.
MODE
SUB
ADJ.
MODE
14A1-RU
14A2-RU
4
A
↓
SOUND SYSTEM M (S-M)
↓
SOUND SYSTEM DK (S-DK)
↓
SOUND SYSTEM I (S-I)
↓
SOUND SYSTEM BG (S-BG)
↓
PLAYBACK SECAM (P-SECAM)
↓
FE (RF) NTSC 3.58 (F-N358)
↓
FE (RF) NTSC 4.43 (F-N443)
↓
FE (RF) SECAM (F-SECAM)
↓
VIDEO MUTE AT IDENT LOSS (VMI)
↓
VIDEO MUTE AT PROGRAM
/SOURCE CHANGE (VMC)
↓
HOTEL MODE (HTL)
↓
REDUCED FM DEMODULATION
GAIN FOR BTSC SIGNAL (BTSC)
↓
4-1
B
↓
↓
NUMBER OF EXT AV SOURCE (AV)
↓
FM WINDOW SEVECTION (FMWS)
↓
SOUND MUTE BIT 0 (SM0)
↓
SOUND MUTE BIT 1 (SM1)
↓
THAI LANGUAGE (THA)
↓
ARABIC LANGUAGE (ARA)
↓
MALAY LANGUAGE (MAL)
↓
CHINESE LANGUAGE (CHI)
↓
FRENCH LANGUAGE (FRE)
↓
RUSSIAN LANGUAGE (RUS)
↓
FORCED V-SYNC SLICING LEVEL(FSL)
↓
SYNC OF OSD (HP2)
↓
TUNER SELECTION (CPT)
A
↓
COLOUR OFFSET (PAL) (COL-OP)
↓
COLOUR OFFSET (SECAM) (COL-OS)
↓
COLOUR OFFSET (NTSC358) (COL-O3)
↓
COLOUR OFFSET (NTSC443) (COL-O4)
↓
SHARPNESS OFFSET (PAL) (SHP-OP)
↓
SHARPNESS OFFSET (SECAM) (SHP-OS)
↓
SHARPNESS OFFSET (NTSC358) (SHP-O3)
↓
SHARPNESS OFFSET (NTSC443) (SHP-O4)
↓
Y-D TIME FOR PAL (TV) (DL-PT)
↓
Y-D TIME FOR SECAM (TV) (DL-ST)
↓
Y-D TIME FOR N358 (TV) (DL-3T)
↓
Y-D TIME FOR N443 (TV) (DL-4T)
↓
Y-D TIME FOR B/W (TV) (DL-TV)
↓
Y-D TIME FOR PAL (AV) (DL-PA)
↓
Y-D TIME FOR SECAM (AV) (DL-SA)
↓
Y-D TIME FOR N358 (AV) (DL-3A)
↓
Y-D TIME FOR N443(AV) (DL-4A)
↓
Y-D TIME FOR B/W (AV) (DL-AV)
*(Y-D : Y-DELAY)
MISC.
OPTION
MODE
OFFSET
ADJ.
MODE
Y-DELAY
ADJ.
MODE
↓
BILINGUAL(BIL)
↓
IF AGC SPEED BIT 0 (AGC0)
↓
IF AGC SPEED BIT 1 (AGC1)
↓
FOA Time Constant-RF (FOA-FE)
↓
FOB Time Constant-RF (FOB-FE)
↓
FOA Time Constant-AV (FOA-AV)
↓
FOB Time Constant-AV (FOB-AV)
B
↓
VERTICAL SCAN DISABLE(VSD)
↓
BLACK STRETCH (BKS)
↓
AUTO VOLUME LEVELING(AVL)
↓
FAST FILTER IF-PLL(FFI)
↓
ENABLE VERTICAL GUARD (EVG)
↓
EHT TRACKING MODE (EHT)
↓
OVERSCAN SWITCH OFF(OSO)
↓
AUTO COLOUR LIMIT(ACL)
↓
FORCED COLOUR LIMIT(FCO)
IC
OPTION
MODE
USER DATA IN SERVICE MODE
(1/60)
*1
S SYSTEM
SUB-SHP
SHARPNESS UP
4-2
SUB-BRI
SUB TINT
TINT UP TINT
SUB-COL
BRIGHTNESS UP
COLOUR UP
SUB-VOL
SUB-CON
HB
S-COR
BLUEBACK
TIMER
EW / /
SYSTEM
CONTRAST UP
H-CENT
TINT DOWN
SHARPNESS DOWN
V-AMP
V-CENT
CONTRAST DOWN
COLOUR DOWN
AGC
V-LIN
FUNCTION
BRIGHTNESS DOWN
SERVICE-ITEM
RC COMMAND
* Direct Key-in Step1 Mode
The flow of Mode lists as following,
AUTO
C SYSTEM
(1/60)
OFF
(1/60)
BLUE BACK
MIN
SHARPNESS
(1/60)
STANDARD
MIN
TINT
MIN
MIN
BRIGHTNESS
(1/60)
(1/60)
S-VOLUME
MIN
COLOUR
USER DATA
WHITE TEMP
MIN
CONTRAST
MODE
*1 : For each CH, before changing
service mode setting.
* While SERVICE mode ON, EEPROM DATA will switch to the service data.
Also, once SERVICE mode OFF, EEPROM will switch back to previous USER DATA.
* In the service mode, the user data establish as below,
14A1-RU
14A2-RU
: Data
: 55H
: 4FH
EEPROM ITEMS
AGC TAKE OVER POINT
VERTICAL SLOPE
VERTICAL AMPLITUDE
VERTICAL SHIFT
HORIZONTAL SHIFT
S-CORRECTION
WHITE POINT RED STD WHITE TEMP
WHITE POINT GREEN STD WHITE TEMP
WHITE POINT BLUE STD WHITE TEMP
WHITE POINT RED COOL WHITE TEMP
WHITE POINT GREEN COOL WHITE TEMP
WHITE POINT BLUE COOL WHITE TEMP
WHITE POINT RED WARM WHITE TEMP
WHITE POINT GREEN WARM WHITE TEMP
WHITE POINT BLUE WARM WHITE TEMP
MAX VOLUME
SUB CONTRAST
SUB COLOUR
SUB BRIGHTNESS
SUB TINT
SUB SHARPNESS
MAX HOTEL VOLUME
HOTEL PROGRAM NUMBER
OSD GRB REFERENCE
BLACK LEVEL OFF-SET R
BLACK LEVEL OFF-SET G
CATHODE DRIVE LEVEL
Y-DELAY TIME FOR PAL(TV) [YD]
Y-DELAY TIME FOR SECAM(TV) [YD]
Y-DELAY TIME FOR N358 (TV) [YD]
Y-DELAY TIME FOR N443 (TV) [YD]
Y-DELAY TIME FOR B/W (TV) [YD]
Y-DELAY TIME FOR PAL (AV) [YD]
Y-DELAY TIME FOR SECAM (AV) [YD]
Y-DELAY TIME FOR N358 (AV) [YD]
Y-DELAY TIME FOR N443 (AV) [YD]
Y-DELAY TIME FOR B/W (AV) [YD]
COLOUR OFFSET (PAL)
COLOUR OFFSET (SECAM)
COLOUR OFFSET (NTSC358)
COLOUR OFFSET (NTSC443)
SHARPNESS OFFSET (PAL)
SHARPNESS OFFSET (SECAM)
SHARPNESS OFFSET (NTSC358)
SHARPNESS OFFSET (NTSC443)
Address
00H
01H
: Data
: 43H
: A1H
5
5-1
OSD
DATA LENGTH INITIAL DATA
AGC
0~63
14
V-LIN
0~63
32
V-AMP
0~63
32
V-CENT
0~63
32
H-CENT
0~63
32
S-COR
0~63
0
DRI-RS
0~63
32
DRI-GS
0~63
32
DRI-BS
0~63
32
DRI-RC
0~63
32
DRI-GC
0~63
32
DRI-BC
0~63
32
DRI-RW
0~63
25
DRI-GW
0~63
32
DRI-BW
0~63
32
SUB-VOL
0~63
63
SUB-CON
0~63
63 (50 *3)
SUB-COL
0~63
32
SUB-BRI
0~63
32
SUB-TINT
0~63
32
SUB-SHP
0~63
32
HTL-VOL
0~63
32
HTL-PRG 0~99 OR>99FOR NONE
255
RGB
0~15
15
CUT-R
0~15
8
CUT-G
0~15
8
CDL
0~15
0
DL-PT
0~15
12
DL-ST
0~15
15
DL-3T
0~15
12
DL-4T
0~15
12
DL-TV
0~15
12
DL-PA
0~15
12
DL-SA
0~15
15
DL-3A
0~15
12
DL-4A
0~15
12
DL-AV
0~15
12
COL-OP
0~15
8
COL-OS
0~15
8
COL-03
0~15
4
COL-O4
0~15
4
SHP-OP
0~15
8
SHP-OS
0~15
4
SHP-O3
0~15
12
SHP-O4
0~15
8
Address
02H
03H
FIX/ADJ
ADJ
ADJ
ADJ
ADJ
ADJ
FIX
FIX
ADJ
ADJ
FIX
FIX
FIX
FIX
FIX
ADJ
FIX
FIX
ADJ
ADJ
ADJ
ADJ
ADJ
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
(DRI-GS)-7 DATA
(DRI-BS)-7 DATA
(DRI-GS)-7 DATA
(DRI-BS)DATA
REMARK
AFTER SHORT JA 122 & JA 124 ,AND TURN ON THE MAIN POWER SWITCH,READ DATA FROM EEPROM
ADDRESS 00H ~ 03H,AND COMPARE TO THE LIST BELOW, IF DIFFERENT, INITIALIZE THE EEPROM.
OSD
VSD
BKS
AVL
FFI
EVG
EHT
OSO
ACL
FCO
S-M
S-DK
S-I
S-BG
P-SECAM
F-N358
F-N443
F-SECAM
VMI
VMC
HTL
BTSC
AV
FMWS
SM0
SM1
THA
ARA
MAL
CHI
FRE
RUS
FSL
HP2
CPT
BIL
AGC0
AGC1
FOA-FE
FOB-FE
FOA-AV
FOB-AV
DATA LENGTH INITIAL DATA
0(DISABLE)/1(ENABLE)
0
0(DISABLE)/1(ENABLE)
1
0(DISABLE)/1(ENABLE)
1
0(DISABLE)/1(ENABLE)
0
0(DISABLE)/1(ENABLE)
1
0(DISABLE)/1(ENABLE)
1
0(DISABLE)/1(ENABLE)
0
0(DISABLE)/1(ENABLE)
0
0(DISABLE)/1(ENABLE)
0
0(DISABLE)/1(ENABLE)
0
0(DISABLE)/1(ENABLE)
0
0(DISABLE)/1(ENABLE)
0
0(DISABLE)/1(ENABLE)
1
0(DISABLE)/1(ENABLE)
1
0(DISABLE)/1(ENABLE)
0
0(DISABLE)/1(ENABLE)
1
0(DISABLE)/1(ENABLE)
1
0(DISABLE)/1(ENABLE)
1
0(DISABLE)/1(ENABLE)
1
0(DISABLE)/1(ENABLE)
0
0(DISABLE)/1(ENABLE)
0
0 FOR1 AV/1 FOR 2AV
1
0(DISABLE)/1(ENABLE)
0
0(DISABLE)/1(ENABLE)
1
0(DISABLE)/1(ENABLE)
0
0(DISABLE)/1(ENABLE)
1
0(DISABLE)/1(ENABLE)
1
0(DISABLE)/1(ENABLE)
1
0(DISABLE)/1(ENABLE)
1
0(DISABLE)/1(ENABLE)
1
0(DISABLE)/1(ENABLE)
1
0(DISABLE)/1(ENABLE)
0
0(DISABLE)/1(ENABLE)
0
0(BRAZIL)/1(ARGENTINA)
0
0(DISABLE)/1(ENABLE)
0
0(DISABLE)/1(ENABLE)
1
0(DISABLE)/1(ENABLE)
0
0(DISABLE)/1(ENABLE)
0
0(DISABLE)/1(ENABLE)
0
0(DISABLE)/1(ENABLE)
1
0(DISABLE)/1(ENABLE)
1
FIX/ADJ
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
FIX
5-2
NOTE :
FIXED DATA,PLEASE DO NOT CHANGE WITHOUT SPECIFIC INSTRUCTION."
*1: MANUALLY CHANGE 1 TO 0.
EEPROM ITEMS
VERTICAL SCAN DISABLE
BLACK STRETCH
AUTOMATIC VOLUME LEVELING
FAST FILTER IF-PLL
ENABLE VERTICAL GUARD (RGB BLANKING)
EHT TRACKING MODE (HCO)
OVERSCAN SWITCH OFF
AUTO COLOUR LIMIT
FORCED COLOUR LIMIT
SOUND SYSTEM M
SOUND SYSTEM DK
SOUND SYSTEM I
SOUND SYSTEM BG
PLAYBACK SECAM
FE (RF) NTSC 3.58
FE (RF) NTSC 4.43
FE (RF) SECAM
VIDEO MUTE AT IDENT LOSS
VIDEO MUTE AT PROGRAM/SOURCE CHANGE
HOTEL MODE
REDUCED FM DEMODULATOR GAIN FOR BTSC SIGNAL
NUMBER OF EXTERNAL AV SOURCE
FM WINDOW SELECTION
SOUND MUTE BIT 0
SOUND MUTE BIT 1
THAI LANGUAGE
ARABIC LANGUAGE
MALAY LANGUAGE
CHINESE LANGUAGE
FRENCH LANGUAGE
RUSSIAN LANGUAGE
FORCED V-SYNC SLICING LEVEL
SYNC OF OSD
TUNER SELECTION (0:SHARP/ALPS; 1:MURATA)
BILINGUAL
IF AGC SPEED BIT 0
IF AGC SPEED BIT 1
PHI-1 TIME CONSTANT (RF)
PHI-1 TIME CONSTANT (RF)
PHI-1 TIME CONSTANT (OFF AIR)
PHI-1 TIME CONSTANT (OFF AIR)
*1
*1
*1
*1
*1
ONLY BLK
REMARK
14A1-RU
14A2-RU
INITIAL SETTING
CH-NO
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
B/G
B/G
D/K
B/G
B/G
D/K
D/K
B/G
M
B/G
B/G
B/G
I
B/G
B/G
B/G
B/G
M
D/K
B/G
I
B/G
B/G
I
B/G
M
M
M
M
M
M
M
M
M
B/G
B/G
B/G
B/G
B/G
B/G
B/G
294.25
463.25
647.25
663.25
679.25
SOUND SYS
48.25
62.25
77.25
175.25
182.25
183.25
191.25
196.25
199.25
210.25
224.25
471.25
487.25
503.25
575.25
583.25
599.25
621.25
639.25
703.25
735.25
767.25
815.25
855.25
855.25
55.25
83.25
183.25
193.25
217.25
471.25
477.25
693.25
885.25
112.25
168.25
MCL1
Fv (MHz)
6-1
44
45
CH-NO
174.95
175.55
MCL1
Fv (MHz)
(1). In service mode, After execute select POS 1, store the following tuning data in EEPROM.
B/G
B/G
SOUND SYS
SHIPPING SETTING & CHECKING
DATA SETTING
1
1
1
AUTO
D/K
OFF
ON
1
60 (MAX)
0 (CENTER)
0 (CENTER)
0 (CENTER)
0 (CENTER)
STANDARD
In-active, "--:--"
In-active, "--:--"
In-active, "--:--"
POWER-ON
RUSSIAN
OFF
OFF
ON
6
LANGAUGE
RUSSIAN
SOUND SYSTEM
D/K
Geomagnetism (H,V) nT
"45,000" "20,000"
Background
7500K
Lang.
RUSSIAN
S-SYS
D/K
6-2
*OSD LANG MUST BE SET IN SERVICE MODE,BUT IT'S BETTER TO WRITE IN EEPROM.
LANGUAGE QUANTITIES:ENGLISH/RUSSIAN
MODEL
J (RU)
FACTORY SETTINGS BY MODELS (Reference: Geomagnetism Adjustment)
MODEL
RU
*1: Please refer defaults for LANGUAGE and SOUND SYSTEM per MODEL as follows,
ITEMS
LAST PROGRAM/CHANNEL
FLASHBACK PROGARM/CH
DIGIT
C-SYSTEM
S-SYSTEM
SKIP
AFC
VOLUME
CONTRAST
COLOUR
BRIGHTNESS
TINT
SHARPNESS
WHITE TEMP
REMINDER TIMER
ON TIMER
OFF TIMER
LAST POWER
LANGUAGE
BLUE BACK MUTE
HOTEL MODE
0 CHANNEL SKIP
(1) The following default data has been factory-set for the E2PROM.
14A1-RU
14A2-RU
Tuner IFT
( PRESET )
RF-AGC
TAKE OVER
POINT ADJUSTMENT
(I2C BUS
CONTROL)
1
2
No. Adjusting point
IF OUT
7
–
+
Fig. 3
» Bias box: About 4.5 V
TV Set
TP201
7-1
3. Call "AG" mode in service mode. Adjust the "AG"
bus data to obtain the Tuner output pin drop 0.1V
below maximum voltage.
4. Change the antenna input signal to 63~67dBµV,
and make sure there is no noise.
5. Turn up the input signal to 90~95 dBµV to be sure
that there is no cross modulation beat.
Bias box
Oscilloscope
+
0.1V
–
2. Connect the oscilloscope to TP201 (Tuner’s AGC
Terminal) as shown in Fig. 3.
Note: For the 50 ohm signal
strength gauge, when not
using 50/75 impedance
adapter, signal strength is
52±1dBµV(75 ohm open), instead of 57±1dBµV (75 ohm
open).
Precaution: The loss of using
impedance adapter
-1.5+/-0.8dB
C
75ohm
1000p
1. Receive "PAL COLOUR BAR" signal.
» Signal Strength: 57 ± 1 dBµV (75 ohm open)
P
E-9 CH
Fig.1
100k
1n60
Fig.2
Oscilloscope
10k
Waveform and others
Note: Be sure to keep the tuner cover in position
during this adjustment.
1. Get the tuner ready to receive the CH. E - 9
signal,but with no signal input.
Adjust the PLL data.
2. Connect the sweep generator's output cable to
the tuner antenna. ( RF SWEEP )
3. Adjust the sweep generator's to 80dBuV.
4. Connect the response lead ( use LOW IMPEDANCE probe with wave detector ; see Fig.1 ) to
the tuner's IF output terminal. ( This terminal
must have the probe alone connected ).
5. Set the RF AGC to 0 - 6 V with no saturation with
the waveform.
6. Adjust the tuner IF coil to obtain the waveform as
shown in Fig. 2.
Adjusting procedure/conditions
PIF ADJUSTMENT
1
PURITY ADJ.
No. Adjusting point
Green-only
7-2
Signal-colour
screen cleared
Blue-only
Red-only
* For the following colours press R/C RGB key to
change.
1. Receive the GREEN-ONLY signal. Adjust the
beam current to about 500 µA.
2. Degauss the CRT enough with the degausing coil.
Note: Follow the Job Instruction Sheet to adjust the magnetic field.
Vertical Bv : +0.040 mT (0.40 gauss)
Horizontal Bh: +0.020 mT (0.20 gauss)
(See page 6.)
3. Maintain the purity magnet at the zero magnetic
field and keep the static convergence roughly
adjusted.
4. Observe the points a, b as shown in Fig. 4-1
through the microscope. Adjust the landing to the
rank A requirements.
5. Orient the raster rotation to 0 eastward.
6. Tighten up the deflection coil screws.
» Tightening torque: 108 ± 20 N (11 ± 2 kgf)
7. Make sure the CRT corners landing meet the A
rank requirements. If not, stick the magnet sheet
to correct it.
Note: This adjustment must be done after
warming up the unit for 30 minutes or
longer with a beam current over 500 µA.
Note: Set the service mode by TP1001 &
TP1002 (short) then press factory process R/C RGB key to change to RGB
mono colour mode.
Adjusting procedure/conditions
PURITY ADJUSTMENT
B
A
Fig. 4-1
A=B
b
A=B
The TEXT Key "R. G. Cy" Key
can be directly use to change
to other colours screen.
* Press R/C RGB key for 1 second in NORMAL MODE, the
colour will change to RGB mono
colour mode.
Rank "A"
(on the left of the CRT)
Fig. 4-3
B
A
Fig. 4-2
Rank "A"
(on the right of the CRT)
a
Waveform and others
14A1-RU
14A2-RU
1
CONVERGENC
ADJ.
( To be done
after the purity
adjustment.
No. Adjusting point
8
8-1
Finally received the Red-only and Blue-only signals to make sure there is no other colours on the
screen.
DYNAMIC CONVERGENCE
1. Adjust the convergence on the fringes of the
screen in the following steps.
a) Fig. 5-1: Drive the wedge at point "a" and swing
the deflection coil upward.
b) Fig. 5-2: Drive the wedge at points "b" and "c"
and swing the deflection coil downward.
c) Fig. 5-3: Drive the "c" wedge deeper and swing
the deflection coil rightward.
d) Fig. 5-4: Drive the "b" wedge deeper and swing
the deflection coil leftward.
2. Fix all the wedges on the CRT and apply glass
tape over them.
3. Apply lacquer to the deflection yoke lock screw,
magnet unit (purity, 4-pole, 6-pole magnets) and
magnet unit lock screw.
STATIC CONVERGENCE
1. Turn the 4-pole magnet to a proper opening angle in order to superpose the blue and red colours.
2. Turn the 6-pole magnet to a proper opening angle in order to superpose the green colour over
the blue and red colours.
1. Receive the "Crosshatch Pattern" signal.
2. Using the remote controller, call NORMAL mode.
Adjusting procedure/conditions
Wedge "a"
Fig. 5-4
Fig. 5-3
BGR
RGB
Wedge
"c"
About
100°
R
G
B
B
G
R
Lacquer
Purity magnet
40cm
4-pole magnet
6-pole magnet
CRT neck
Wedge
"b"
Lacquer
About
100°
R
G
B
B
G
R
Fig. 5-2
RGB
Fig. 5-1
BGR
Waveform and others
CONVERGENCE ADJUSTMENT
Maximum
beam check
WHITE BALANCE SERVICE MODE
ADJ. (I2C BUS
CONTROL)
3
4
SUB-BRIGHTNESS
ADJUSMENT
(I2C BUS
CONTROL)
CRT CUTOFF
ADJUSTMENT
(I2C BUS
CONTROL)
2
1
No. Adjusting point
: 1 V/Div (DC)
: 5 msec/Div
8-2
1. Receive the "Monoscope Pattern" signal.
2. Press R/C to set Picture NORMAL condition.
3. Connect the DC miliammeter between TP603 (+)
and TP602 (–).
(Full Scale: 3 mA Range)
4. Beam current must be within 800 ± 100 µA.
* ADJUST DRI-GC/GW, DRI-BC/BW as following
DATA, after finishing DRI-BS and DRI-GS DATA
ADJUSTMENT.
DRI-RW=32 (FIXED), DRI-GW="DRI-GS"-7*,
DRI-BW="DRI-BS"-7*DRI-RC=25*,
DRIBC="DRI-BS", DRI-GC="DRI-GS"-7*
Note: This adjustment must be done after
warming up the unit for 30 minutes or
longer with a beam current over 500µA.
1. Receive the "Monoscope Pattern" signal.
2. Press R/C to set Picture NORMAL condition.
3. Connect the DC miliammeter between the TP 602
( - ) TP 603 ( + ).
4. Check Beam current should be around 800µA)
5. Set it to service mode and adjust the DRI-GS, &
DRI-BS data to have a colour temperature of
7500°K ( white ).
6. Receive "WHITE" pattern, WITH BURST signal,
and set BRIGHTNESS Y by generator, to ** 10
cd/m2 (MINOLTA CA-100) by reducing
LUMINATE Y signal.
7. Adjust "CUT-R" & "CUT-G" to get 7,500. Then go
back NORMAL mode (HIGH BRIGHT**) to check
colour temperature. If out of range, back to (1).
1. Call " SUB-BRI" in service mode. (Receive Crosshatch pattern with 5 black level windows)
2. Adjust the " SUB BRIGHT " bus data in order that
the line 1, 2 and 3 have the same darkness
wherelse line 4 is slightly brighter than line 1, 2
and 3 and finally line 5 will be the brighter than
line 4.
4. Adjust SCREEN VR ,so that the tip of signal reach
3.0 Vdc + 0.1 Vdc.
Range
Sweep
1. Switch TV to VIDEO mode,BLUE BACK OFF, with
NO VIDEO signal.
2. Press R/C to set Picture Normal condition.
3. Connect the oscilloscope to Red OUT from
IC801.(TP851)
Adjusting procedure/conditions
1 2 3 4 5
1V
LOW
HIGH
10cd/m2 200cd/m2
10cd/m2 120cd/m2
* 7500° K
DRI-GW="DRI-GS"DATA-5
DRI-BW="DRI-BS" DATA-5
14"
20"/21"
( MINOLTA COLOUR ANALYZER
CA-100)
*NOTE: Above DATA can be UP/
DOWN by volume key.
Refer to Page 6.
# 7500° K X : 0.300
Y : 0.310
1, 2, 3 are in same black level.
0
3.0Vdc
Waveform and others
CRT CUT-OFF, BACKGROUND AND SUB-CONTRAST ADJUSTMENT
14A1-RU
14A2-RU
FIXED DATA, NO NEED TO ADJUST.
1. Call the "H-CENT" mode.
2. Increase or decrease "H-CENT" by Volume key
to center the picture horizontal.
V - AMP (I2C
BUS CONTROL)
S-CORRECTION (I2C BUS
CONTROL)
H - CENTER
Focus
adjustment
3
4
5
6
9
1
SUB COLOUR
(I2C BUS
CONTROL)
No. Adjusting point
V-CENTER (I2C 1. Call the "V-CENT" mode.
2. Increase or decrease "V-CENT" by Volume key
BUS CONtill the picture is centered.
TROL)
2
Waveform and others
9-1
4. Using the R/C call "SUB COL" in SERVICE mode.
Adjust SUB COLOUR bus data, so that the 75%
White & Red portions of PAL Colour Bar be at the
same level shown as Fig. 8.
5. Clear the SERVICE mode.
1. Receive the "PAL Colour Bar" signal.
2. Press R/C to set Picture Normal condition.
3. Connect the oscilloscope to Red cathode(TP854).
» Range
: 20 V/div. (AC) (Using 10:1 probe)
» Sweep time : 10 µsec/div.
Adjusting procedure/conditions
W Y 100%W Mg R
75%
Fig. 8
Cy G
B
Waveform and others
PAL CHROMA ADJUSTMENT
1. Receive the "Monoscope Pattern" signal.
2. Press R/C to set Picture NORMAL condition.
3. Adjust the focus control to get the best focus.
1. Call the "V-AMP" mode.
2. Increase or decrease "V - AMP" by Volume key
to set overscan of 9.5% typical.
Adjustment Spec 9.5% range +1% -0%.
V-SLOPE(I C
BUS CONTROL)
1. Receive Monoscope Pattern Signal.
2. Call the "V-LIN" mode.
3. Increase or decrease "V-LIN" by Volume key till
the horizontal line in the center of monoscope is
just at the position where the blanking starts.
Adjusting procedure/conditions
1
2
No. Adjusting point
HORIZONTAL AND VERTICAL DEFLECTION LOOP ADJUSTMENT
Other
protectors
Fig. 9
W Y Cy G Mg R B
SAME LEVEL
Waveform and others
1. Once finish rectified Electrolytic Capacitor short
testing in +B line, check all possible damaged
components on +B line.
(Use random selected set for inspection)
1. Receive "Monoscope Pattern" signal.
2. Connect output of Bias Box to D607 cathode
(R606 side).
3. Set voltage of Bias Box to 18V and make sure
the protector is not work.
4. Set voltage of Bias Box to 27V, and make sure
the protector is work.
1. Receive "Monoscope Pattern" signal.
2. Set CONTRAST MAX.
3. Set BRIGHT MAX.
4. During the Collector & Emitter of Q883/5/7 short,
make sure the protector ON and switch to standby
mode.
Adjusting procedure/conditions
* Select one of Q883/5/7 to do
each short test.
Waveform and others
VIDEO AND
AUDIO
OUTPUT
CHECK
VIDEO AND
AUDIO INPUT
CHECK
1
2
9-2
1. Using the TV/AV key on the remote controller,
make sure that the modes change in order of TV,
AV1, AV2 & TV again and the video & audio output are according to the input terminal for each
mode.
1. Receive the "PAL Color Bar" signal (100% White
Color Bar, Sound 400 Hz 100% Mod.)
2. Terminate the Video output with a 75 ohm impedance. Make sure the output is as specified (1.0
Vp-p ±3 dB).
3. Terminate the Audio output with a 10k ohm impedance. Make sure the output is as specified
(1.76 Vp-p ±3 dB).
Adjusting procedure/conditions
Waveform and others
A/V INPUT AND OUTPUT CHECKING
H, V PROTECTOR
BEAM PROTECTOR
No. Adjusting point
3
2
1
3. Call the "SUB-TINT" mode in service mode. Adjust the "SUB-TINT" bus data to obtain the waveform shown as Fig. 9.
4. Clear the SERVICE mode.
1. Receive the "NTSC3.58 Colour Bar" signal
through AV in.
2. Connect the oscilloscope to TP853 (Pin (5) of
P882) BLUE-OUT.
» Range
: 100mV/div. (AC)(Use Probe 10:1)
» Sweep time : 10 µsec/div.
Adjusting procedure/conditions
NTSC CHROMA ADJUSTMENT
PROTECTOR OPERATION CHECKING
SUB-TINT (I2C
BUS CONTROL)
No. Adjusting point
1
No. Adjusting point
14A1-RU
14A2-RU
10
WHITE TEMP
8
SHARPNESS
Key
5
NORMAL Key
TINT key
4
7
BRIGHTNESS
key
3
CH DISPLAY
COLOUR
COLOUR key
2
6
CONTRAST
key
1
No. Adjusting point
CONTRAST
COLOUR
BRIGHTNESS
TINT
SHARPNESS
: MAX
: CENTER
: CENTER
: CENTER
: CENTER
10-1
1. Receive "Monoscope Pattern" signal.
2. Set FUNCTION to select WHITE TEMP.
3. Press Volume Up/Down key to check WHITE
TEMP Option, STANDARD:
NORMAL SETTING, WARM for more REDDISH
direction changing, COOL for more BLUISH direction changing.
»
»
»
»
»
1. Once in PICTURE Mode, and theNORMAL key
is pressed, all the settings will be present to normal setting.
(Normal setting value for every mode).
1. All Ch (1~99) will have an OSD display of the
channel number in green colour under AFT ON
condition.
1. Receive "Monoscope Pattern" signal.
2. Set P-mode to select SHARPNESS.
3. Press Volume Up/Down key to check whether
the SHARPNESS effect is OK or not.
1. Receive the "NTSC Colour Bar" signal thru AV in.
2. Set P-Mode to select TINT.
3. Press Volume Up/Down key to check TINT, UP
for GREEN direction and DOWN for PURPLE direction whether is OK or not.
1. Receive "Monoscope Pattern" signal.
2. Set P-Mode to select BRIGHTNESS.
3. Press Volume Up/Down key to check whether
the BRIGHTNESS effect is OK or not.
1. Receive "Color Bar" signal.
2. Set P-Mode to select COLOUR.
3. Press Volume Up/Down key to check whether
the COLOUR effect is OK or not.
1. Receive "Monoscope Pattern" signal.
2. Set P-Mode to select CONTRAST.
3. Press Volume Up/Down key to check whether the
CONTRAST effect is OK or not.
Adjusting procedure/conditions
Notes:If nothing is display
mean contrast, colour, bright,
tint, sharpness are all in normal setting.
Waveform and others
FUNCTION OPERATION CHECKING (VIDEO AND AUDIO)
12
11
10
9
OSD LANGUAGE
QUANTITY
CHECK
NOISE MUTE
CHECKING
SOUND
SYSTEM
COLOUR
SYSTEM
No. Adjusting point
10-2
Check OSD LANGUAGE quantity and type as English and Russian.
1. Receive "PAL COLOUR BAR" signal.
2. Turn up the volume control to maximum, make
sure the sound is heard from the speakers. Then
put the unit in no signal state.
3. Check the sound mute is effective.
4. Finally turn sound level of CTV to minimum.
1. Receive "PAL-D/K" signal, press the "SOUND
SYSTEM" to select B/G, I. Check the sound output is not working properly. Select D/K and check
the sound output to make sure it is working properly.
2. Receive "PAL-I" signal, press the "SOUND SYSTEM" to select B/G, D/K. Check the sound output
is not working properly. Select I and check the
sound output to make sure it is working properly.
3. Receive "PAL-B/G" signal, press the "SOUND
SYSTEM"to select I, D/K. Check the sound output is not working properly. Select B/G and check
the sound output to make sure it is working properly.
1. Receive the "PAL COLOUR BAR" signal, press
the COLOUR SYSTEM key to select modes except PAL, check the COLOUR is not working properly. Then, select the "PAL" mode. Check again
its colour so that it is working properly.
2. Receive "NTSC 4.43/3.58 COLOUR BAR" signal
thru AV, press COLOUR SYSTEM key to select
modes except N4.43/3.58, check the COLOUR
is not working properly. Then, select the "NTSC
4.43/3.58" mode. Check again its colour so that it
is working properly.
Adjusting procedure/conditions
(Continued)
Waveform and others
FUNCTION OPERATION CHECKING (VIDEO AND AUDIO)
14A1-RU
14A2-RU
14A1-RU
14A2-RU
MEMORY MAP
(HEX)
D7
00
01
02
03
04
05
06
D6
D5
D4
D3
D2
D1
D0
PASS WORD
PASS WORD
PASS WORD
PASS WORD
MICON
EEPROM
EEPROM
DEFAULT
RANGE
WRITE(CPU)
55
4F
43
A1
00-FF
00-FF
00-FF
00-FF
07
08
V-SLOPE
0E
20
00-3F
00-3F
V-AMPLITUDE
20
00-3F
09
V-CENTER
0A
0B
0C
0D
0E
0F
10
11
12
H-CENTER
20
20
20
20
00-3F
00-3F
00-3F
00-3F
HORIZONTAL-BOW
20
20
20
20
20
00-3F
00-3F
00-3F
00-3F
00-3F
S-CORRECTION
00
00-3F
DRIVE-R (STANDARD)
20
20
20
00-3F
00-3F
00-3F
DRIVE-B (WARM)
20
20
20
20
20
20
00-3F
00-3F
00-3F
00-3F
00-3F
00-3F
SUB-VOLUME
3F
00-3F
SUB-CONTRAST
3F
20
00-3F
00-3F
20
20
20
20
FF
00-3F
00-3F
00-3F
00-3F
00-FF
AGC TAKE-OVER
H-SIZE
EW-PARALLELOGRAM
EW-PARABOLA/WIDTH
EW-UPPER CORNER
EW-LOWER CORNER
EW-TRAPEZIUM
CHASSIS
CHECK DATA
CHECK TYPE
CTV FINAL
CHECK DATA
CHECK TYPE
LAST INITIAL
SETTING DATA
REMARK
11-2
DATA
ADDRESS
14
15
16
17
18
19
DRIVE-G (STANDARD)
DRIVE-B (STANDARD)
DRIVE-R (COOL)
1A
1B
1C
1D
1E
1F
20
21
22
DRIVE-G (COOL)
DRIVE-B (COOL)
DRIVE-R (WARM)
DRIVE-G (WARM)
23
24
25
SUB-COLOUR
SUB-BRIGHTNESS
26
27
SUB-TINT
SUB-SHARPNESS
28
29
2A
2B
2C
2D
HTL-VOLUME
HTL-PROGRAM-NUM
2E
2F
30
OSD-RGB-REFERENCE
0F
00-0F
CUTOFF LEVEL -OFFSET R
08
08
00
00-0F
00-0F
00-0F
0C
0F
0C
00-0F
00-0F
00-0F
0C
0C
00-0F
00-0F
0C
0F
0C
00-0F
00-0F
00-0F
0C
0C
00-0F
00-0F
08
08
04
04
08
00-0F
00-0F
00-0F
00-0F
00-0F
CUTOFF LEVEL -OFFSET G
CATHODE DRIVE LEVEL
31
32
Y-DELAY (TV PAL)
Y-DELAY (TV SECAM)
33
34
Y-DELAY (TV N358)
35
Y-DELAY (TV BW)
36
37
38
Y-DELAY (AV SECAM)
39
Y-DELAY (AV N358)
3A
3B
Y-DELAY (AV BW)
Y-DELAY (TV N443)
Y-DELAY (AV PAL)
Y-DELAY (AV N443)
COLOUR-OFFSET (PAL)
3C
3D
3E
3F
COLOUR-OFFSET (SECAM)
COLOUR-OFFSET (N358)
COLOUR-OFFSET (N433)
SHARPNESS-OFFSET (PAL)
MODEL
MODEL
LETTER NO.
LETTER NO.
11
11-1
13
14A1-RU
14A2-RU
DATA
ADDRESS
(HEX)
D7
D6
D5
D4
D3
D2
D1
D0
MICON
EEPROM
EEPROM
DEFAULT
RANGE
WRITE(CPU)
00-0F
40
SHARPNESS-OFFSET (SECAM)
04
41
SHARPNESS-OFFSET (N358)
0C
00-0F
42
SHARPNESS-OFFSET (N433)
08
00-0F
CHASSIS
CHECK DATA
CHECK TYPE
CTV FINAL
CHECK DATA
LAST INITIAL
SETTING DATA
REMARK
43
44
FCO
ACL
OSO
EHT
EVG
FFI
AVL
BKS
00-FF
45
SCM
N443
N358
PB-SEC
BG
I
DK
M
00-FF
FMWS
AV
BTSC
HTL
VMC
VMI
00-FF
RUS
FRA
CHN
MLY
ARB
THA
00-FF
BIL
CPT
00-FF
46
47
SM
HP2
FSL
48
AGC
49
4A
4B
VOLUME
01
4D
CONTRAST
3C
00-3C
00-3C
4E
COLOUR
1E
00-3C
4F
BRIGHTNESS
1E
00-3C
50
TINT
1E
00-3C
51
SHARPNESS
1E
00-3C
00-FF
12-2
4C
52
53
54
55
POSITION/AV1/AV2
01
56
FAV-POS A
0A
00-FF
57
FAV-POS B
14
00-FF
58
FAV-POS C
1E
00-FF
59
FAV-POS D
28
00-FF
5C
POWER
00
00-01
5D
WHITE-TEMP
00
00-02
5E
BLUE BACK
00
00-01
5F
LANGUAGE
00
00-07
60
DIGIT
00
00-01
5A
5B
61
62
SKIP 0
SKIP 1
SKIP 2
SKIP 3
SKIP 4
SKIP 5
SKIP 6
SKIP 7
80
00-FF
63
SKIP 8
SKIP 9
SKIP 10
SKIP 11
SKIP 12
SKIP 13
SKIP 14
SKIP 15
00
00-FF
64
SKIP 16
SKIP 17
SKIP 18
SKIP 19
SKIP 20
SKIP 21
SKIP 22
SKIP 23
00
00-FF
65
SKIP 24
SKIP 25
SKIP 26
SKIP 27
SKIP 28
SKIP 29
SKIP 30
SKIP 31
00
00-FF
66
SKIP 32
SKIP 33
SKIP 34
SKIP 35
SKIP 36
SKIP 37
SKIP 38
SKIP 39
00
00-FF
67
SKIP 40
SKIP 41
SKIP 42
SKIP 43
SKIP 44
SKIP 45
SKIP 46
SKIP 47
00
00-FF
68
SKIP 48
SKIP 49
SKIP 50
SKIP 51
SKIP 52
SKIP 53
SKIP 54
SKIP 55
00
00-FF
69
SKIP 56
SKIP 57
SKIP 58
SKIP 59
SKIP 60
SKIP 61
SKIP 62
SKIP 63
00
00-FF
6A
SKIP 64
SKIP 65
SKIP 66
SKIP 67
SKIP 68
SKIP 69
SKIP 70
SKIP 71
00
00-FF
6B
SKIP 72
SKIP 73
SKIP 74
SKIP 75
SKIP 76
SKIP 77
SKIP 78
SKIP 79
00
00-FF
6C
SKIP 80
SKIP 81
SKIP 82
SKIP 83
SKIP 84
SKIP 85
SKIP 86
SKIP 87
00
00-FF
6D
SKIP 88
SKIP 89
SKIP 90
SKIP 91
SKIP 92
SKIP 93
SKIP 94
SKIP 95
00
00-FF
6E
SKIP 96
SKIP 97
SKIP 98
SKIP 99
00
00-FF
6F
70
71
72
73
74
TUNING FREQUANCY (HIGHER PART)
S-SYS
75
TUNING FREQUANCY (LOWER PART)
000:BG
S-SYS
AFT
(auto)
001:I
C-SYS
77
TUNING FREQUANCY (HIGHER PART)
O1O:DK
78
TUNING FREQUANCY (LOWER PART)
011:M
79
S-SYS
AFT
(auto)
C-SYS
7A
TUNING FREQUANCY (HIGHER PART)
AFT
7B
TUNING FREQUANCY (LOWER PART)
0:OFF
7C
S-SYS
AFT
(auto)
7D
TUNING FREQUANCY (HIGHER PART)
7E
TUNING FREQUANCY (LOWER PART)
7F
S-SYS
AFT
(auto)
POS 1
POS 2
1:ON
C-SYS
POS 3
C-SYS
MODEL
MODEL
LETTER NO.
LETTER NO.
12
12-1
76
POS 0
14A1-RU
14A2-RU
DATA
ADDRESS
D7
D6
80
D5
D4
D3
D2
D1
D0
MICON
EEPROM
EEPROM
DEFAULT
RANGE
WRITE(CPU)
TUNING FREQUANCY (HIGHER PART)
81
CHASSIS
CHECK DATA
CHECK TYPE
CTV FINAL
CHECK DATA
CHECK TYPE
LAST INITIAL
SETTING DATA
REMARK
POS 4
TUNING FREQUANCY (LOWER PART)
S-SYS
AFT
(auto)
83
TUNING FREQUANCY (HIGHER PART)
84
TUNING FREQUANCY (LOWER PART)
85
S-SYS
AFT
(auto)
86
TUNING FREQUANCY (HIGHER PART)
87
TUNING FREQUANCY (LOWER PART)
88
S-SYS
AFT
(auto)
89
TUNING FREQUANCY (HIGHER PART)
8A
TUNING FREQUANCY (LOWER PART)
8B
S-SYS
AFT
(auto)
8C
TUNING FREQUANCY (HIGHER PART)
8D
TUNING FREQUANCY (LOWER PART)
8E
S-SYS
AFT
(auto)
8F
TUNING FREQUANCY (HIGHER PART)
90
TUNING FREQUANCY (LOWER PART)
91
S-SYS
AFT
(auto)
92
TUNING FREQUANCY (HIGHER PART)
93
TUNING FREQUANCY (LOWER PART)
94
S-SYS
AFT
(auto)
95
TUNING FREQUANCY (HIGHER PART)
96
TUNING FREQUANCY (LOWER PART)
97
S-SYS
AFT
(auto)
98
TUNING FREQUANCY (HIGHER PART)
99
TUNING FREQUANCY (LOWER PART)
9A
S-SYS
AFT
(auto)
9B
TUNING FREQUANCY (HIGHER PART)
9C
TUNING FREQUANCY (LOWER PART)
9D
S-SYS
AFT
(auto)
9E
TUNING FREQUANCY (HIGHER PART)
9F
TUNING FREQUANCY (LOWER PART)
A0
S-SYS
AFT
(auto)
A1
TUNING FREQUANCY (HIGHER PART)
A2
TUNING FREQUANCY (LOWER PART)
A3
S-SYS
AFT
(auto)
A4
TUNING FREQUANCY (HIGHER PART)
A5
TUNING FREQUANCY (LOWER PART)
A6
S-SYS
AFT
(auto)
A7
TUNING FREQUANCY (HIGHER PART)
A8
TUNING FREQUANCY (LOWER PART)
A9
S-SYS
AFT
(auto)
AA
TUNING FREQUANCY (HIGHER PART)
AB
TUNING FREQUANCY (LOWER PART)
AC
S-SYS
AFT
(auto)
AD
TUNING FREQUANCY (HIGHER PART)
AE
TUNING FREQUANCY (LOWER PART)
AF
S-SYS
AFT
(auto)
B0
TUNING FREQUANCY (HIGHER PART)
B1
TUNING FREQUANCY (LOWER PART)
B2
S-SYS
AFT
(auto)
B3
TUNING FREQUANCY (HIGHER PART)
B4
TUNING FREQUANCY (LOWER PART)
B5
S-SYS
AFT
(auto)
B6
TUNING FREQUANCY (HIGHER PART)
B7
TUNING FREQUANCY (LOWER PART)
B8
S-SYS
AFT
(auto)
B9
TUNING FREQUANCY (HIGHER PART)
BA
TUNING FREQUANCY (LOWER PART)
BB
S-SYS
AFT
(auto)
BC
TUNING FREQUANCY (HIGHER PART)
BD
TUNING FREQUANCY (LOWER PART)
BE
S-SYS
BF
AFT
(auto)
C-SYS
POS 5
C-SYS
POS 6
C-SYS
POS 7
C-SYS
POS 8
C-SYS
POS 9
C-SYS
POS 10
13-2
82
C-SYS
POS 11
C-SYS
POS 12
C-SYS
POS 13
C-SYS
POS 14
C-SYS
POS 15
C-SYS
POS 16
C-SYS
POS 17
C-SYS
POS 18
C-SYS
POS 19
C-SYS
POS 20
C-SYS
POS 21
C-SYS
POS 22
C-SYS
POS 23
13-1
(HEX)
C-SYS
POS 24
C-SYS
TUNING FREQUANCY (HIGHER PART)
POS 25
MODEL
MODEL
LETTER NO.
LETTER NO.
13
14A1-RU
14A2-RU
DATA
D7
D6
C0
D5
D4
D3
D2
D1
D0
MICON
EEPROM
EEPROM
DEFAULT
RANGE
WRITE(CPU)
TUNING FREQUANCY (LOWER PART)
C1
S-SYS
AFT
(auto)
C2
TUNING FREQUANCY (HIGHER PART)
C3
TUNING FREQUANCY (LOWER PART)
C4
S-SYS
AFT
(auto)
C5
TUNING FREQUANCY (HIGHER PART)
C6
TUNING FREQUANCY (LOWER PART)
C7
S-SYS
AFT
(auto)
C8
TUNING FREQUANCY (HIGHER PART)
C9
TUNING FREQUANCY (LOWER PART)
CA
S-SYS
AFT
(auto)
CB
TUNING FREQUANCY (HIGHER PART)
CC
TUNING FREQUANCY (LOWER PART)
CD
S-SYS
AFT
(auto)
CE
TUNING FREQUANCY (HIGHER PART)
CF
TUNING FREQUANCY (LOWER PART)
D0
S-SYS
AFT
(auto)
D1
TUNING FREQUANCY (HIGHER PART)
D2
TUNING FREQUANCY (LOWER PART)
D3
S-SYS
AFT
(auto)
D4
TUNING FREQUANCY (HIGHER PART)
D5
TUNING FREQUANCY (LOWER PART)
D6
S-SYS
AFT
(auto)
D7
TUNING FREQUANCY (HIGHER PART)
D8
TUNING FREQUANCY (LOWER PART)
D9
S-SYS
AFT
(auto)
DA
TUNING FREQUANCY (HIGHER PART)
DB
TUNING FREQUANCY (LOWER PART)
DC
S-SYS
AFT
(auto)
DD
TUNING FREQUANCY (HIGHER PART)
DE
TUNING FREQUANCY (LOWER PART)
DF
S-SYS
AFT
(auto)
E0
TUNING FREQUANCY (HIGHER PART)
E1
TUNING FREQUANCY (LOWER PART)
E2
S-SYS
AFT
(auto)
E3
TUNING FREQUANCY (HIGHER PART)
E4
TUNING FREQUANCY (LOWER PART)
E5
S-SYS
AFT
(auto)
E6
TUNING FREQUANCY (HIGHER PART)
E7
TUNING FREQUANCY (LOWER PART)
E8
S-SYS
AFT
(auto)
E9
TUNING FREQUANCY (HIGHER PART)
EA
TUNING FREQUANCY (LOWER PART)
EB
S-SYS
AFT
(auto)
EC
TUNING FREQUANCY (HIGHER PART)
ED
TUNING FREQUANCY (LOWER PART)
EE
S-SYS
AFT
(auto)
EF
TUNING FREQUANCY (HIGHER PART)
F0
TUNING FREQUANCY (LOWER PART)
F1
S-SYS
AFT
(auto)
F2
TUNING FREQUANCY (HIGHER PART)
F3
TUNING FREQUANCY (LOWER PART)
F4
S-SYS
AFT
(auto)
F5
TUNING FREQUANCY (HIGHER PART)
F6
TUNING FREQUANCY (LOWER PART)
F7
S-SYS
AFT
(auto)
F8
TUNING FREQUANCY (HIGHER PART)
F9
TUNING FREQUANCY (LOWER PART)
FA
S-SYS
AFT
(auto)
FB
TUNING FREQUANCY (HIGHER PART)
FC
TUNING FREQUANCY (LOWER PART)
FD
S-SYS
AFT
(auto)
CHASSIS
CHECK DATA
CHECK TYPE
CTV FINAL
CHECK DATA
CHECK TYPE
LAST INITIAL
SETTING DATA
REMARK
POS 25
C-SYS
POS 26
C-SYS
POS 27
C-SYS
POS 28
C-SYS
POS 29
C-SYS
POS 30
C-SYS
POS 31
14-2
(HEX)
C-SYS
POS 32
C-SYS
POS 33
C-SYS
POS 34
C-SYS
POS 35
C-SYS
POS 36
C-SYS
POS 37
C-SYS
POS 38
C-SYS
POS 39
C-SYS
POS 40
C-SYS
POS 41
C-SYS
POS 42
C-SYS
POS 43
C-SYS
POS 44
C-SYS
POS 45
C-SYS
FE
POS 46
FF
MODEL
MODEL
LETTER NO.
LETTER NO.
14
14-1
ADDRESS
14A1-RU
14A2-RU
DATA
ADDRESS
D7
D6
D5
D4
D3
D2
D1
D0
MICON
EEPROM
EEPROM
DEFAULT
RANGE
WRITE(CPU)
100
CHASSIS
CHECK DATA
CHECK TYPE
CTV FINAL
CHECK DATA
CHECK TYPE
LAST INITIAL
SETTING DATA
REMARK
POS 46
TUNING FREQUANCY (HIGHER PART)
102
TUNING FREQUANCY (LOWER PART)
103
S-SYS
AFT
(auto)
104
TUNING FREQUANCY (HIGHER PART)
105
TUNING FREQUANCY (LOWER PART)
106
S-SYS
AFT
(auto)
107
TUNING FREQUANCY (HIGHER PART)
108
TUNING FREQUANCY (LOWER PART)
109
S-SYS
AFT
(auto)
10A
TUNING FREQUANCY (HIGHER PART)
10B
TUNING FREQUANCY (LOWER PART)
10C
S-SYS
AFT
(auto)
10D
TUNING FREQUANCY (HIGHER PART)
10E
TUNING FREQUANCY (LOWER PART)
10F
S-SYS
AFT
(auto)
110
TUNING FREQUANCY (HIGHER PART)
111
TUNING FREQUANCY (LOWER PART)
112
S-SYS
AFT
(auto)
113
TUNING FREQUANCY (HIGHER PART)
114
TUNING FREQUANCY (LOWER PART)
115
S-SYS
AFT
(auto)
116
TUNING FREQUANCY (HIGHER PART)
117
TUNING FREQUANCY (LOWER PART)
118
S-SYS
AFT
(auto)
119
TUNING FREQUANCY (HIGHER PART)
11A
TUNING FREQUANCY (LOWER PART)
11B
S-SYS
AFT
(auto)
11C
TUNING FREQUANCY (HIGHER PART)
11D
TUNING FREQUANCY (LOWER PART)
11E
S-SYS
AFT
(auto)
11F
TUNING FREQUANCY (HIGHER PART)
120
TUNING FREQUANCY (LOWER PART)
121
S-SYS
AFT
(auto)
122
TUNING FREQUANCY (HIGHER PART)
123
TUNING FREQUANCY (LOWER PART)
124
S-SYS
AFT
(auto)
125
TUNING FREQUANCY (HIGHER PART)
126
TUNING FREQUANCY (LOWER PART)
127
S-SYS
AFT
(auto)
128
TUNING FREQUANCY (HIGHER PART)
129
TUNING FREQUANCY (LOWER PART)
12A
S-SYS
AFT
(auto)
12B
TUNING FREQUANCY (HIGHER PART)
12C
TUNING FREQUANCY (LOWER PART)
12D
S-SYS
AFT
(auto)
12E
TUNING FREQUANCY (HIGHER PART)
12F
TUNING FREQUANCY (LOWER PART)
130
S-SYS
AFT
(auto)
131
TUNING FREQUANCY (HIGHER PART)
132
TUNING FREQUANCY (LOWER PART)
133
S-SYS
AFT
(auto)
134
TUNING FREQUANCY (HIGHER PART)
135
TUNING FREQUANCY (LOWER PART)
136
S-SYS
AFT
(auto)
137
TUNING FREQUANCY (HIGHER PART)
138
TUNING FREQUANCY (LOWER PART)
139
S-SYS
AFT
(auto)
13A
TUNING FREQUANCY (HIGHER PART)
13B
TUNING FREQUANCY (LOWER PART)
13C
S-SYS
AFT
(auto)
13D
TUNING FREQUANCY (HIGHER PART)
13E
TUNING FREQUANCY (LOWER PART)
13F
S-SYS
AFT
(auto)
POS 47
C-SYS
POS 48
C-SYS
POS 49
C-SYS
POS 50
C-SYS
POS 51
C-SYS
POS 52
15-2
101
C-SYS
POS 53
C-SYS
POS 54
C-SYS
POS 55
C-SYS
POS 56
C-SYS
POS 57
C-SYS
POS 58
C-SYS
POS 59
C-SYS
POS 60
C-SYS
POS 61
C-SYS
POS 62
C-SYS
POS 63
C-SYS
POS 64
C-SYS
POS 65
C-SYS
POS 66
C-SYS
POS 67
C-SYS
MODEL
MODEL
LETTER NO.
LETTER NO.
15
15-1
(HEX)
14A1-RU
14A2-RU
DATA
ADDRESS
D7
D6
140
D5
D4
D3
D2
D1
D0
MICON
EEPROM
EEPROM
DEFAULT
RANGE
WRITE(CPU)
TUNING FREQUANCY (HIGHER PART)
141
CHASSIS
CHECK DATA
CHECK TYPE
CTV FINAL
CHECK DATA
CHECK TYPE
LAST INITIAL
SETTING DATA
REMARK
POS 68
TUNING FREQUANCY (LOWER PART)
S-SYS
AFT
(auto)
143
TUNING FREQUANCY (HIGHER PART)
144
TUNING FREQUANCY (LOWER PART)
145
S-SYS
AFT
(auto)
146
TUNING FREQUANCY (HIGHER PART)
147
TUNING FREQUANCY (LOWER PART)
148
S-SYS
AFT
(auto)
149
TUNING FREQUANCY (HIGHER PART)
14A
TUNING FREQUANCY (LOWER PART)
14B
S-SYS
AFT
(auto)
14C
TUNING FREQUANCY (HIGHER PART)
14D
TUNING FREQUANCY (LOWER PART)
14E
S-SYS
AFT
(auto)
14F
TUNING FREQUANCY (HIGHER PART)
150
TUNING FREQUANCY (LOWER PART)
151
S-SYS
AFT
(auto)
152
TUNING FREQUANCY (HIGHER PART)
153
TUNING FREQUANCY (LOWER PART)
154
S-SYS
AFT
(auto)
155
TUNING FREQUANCY (HIGHER PART)
156
TUNING FREQUANCY (LOWER PART)
157
S-SYS
AFT
(auto)
158
TUNING FREQUANCY (HIGHER PART)
159
TUNING FREQUANCY (LOWER PART)
15A
S-SYS
AFT
(auto)
15B
TUNING FREQUANCY (HIGHER PART)
15C
TUNING FREQUANCY (LOWER PART)
15D
S-SYS
AFT
(auto)
15E
TUNING FREQUANCY (HIGHER PART)
15F
TUNING FREQUANCY (LOWER PART)
160
S-SYS
AFT
(auto)
161
TUNING FREQUANCY (HIGHER PART)
162
TUNING FREQUANCY (LOWER PART)
163
S-SYS
AFT
(auto)
164
TUNING FREQUANCY (HIGHER PART)
165
TUNING FREQUANCY (LOWER PART)
166
S-SYS
AFT
(auto)
167
TUNING FREQUANCY (HIGHER PART)
168
TUNING FREQUANCY (LOWER PART)
169
S-SYS
AFT
(auto)
16A
TUNING FREQUANCY (HIGHER PART)
16B
TUNING FREQUANCY (LOWER PART)
16C
S-SYS
AFT
(auto)
16D
TUNING FREQUANCY (HIGHER PART)
16E
TUNING FREQUANCY (LOWER PART)
16F
S-SYS
AFT
(auto)
170
TUNING FREQUANCY (HIGHER PART)
171
TUNING FREQUANCY (LOWER PART)
172
S-SYS
AFT
(auto)
173
TUNING FREQUANCY (HIGHER PART)
174
TUNING FREQUANCY (LOWER PART)
175
S-SYS
AFT
(auto)
176
TUNING FREQUANCY (HIGHER PART)
177
TUNING FREQUANCY (LOWER PART)
178
S-SYS
AFT
(auto)
179
TUNING FREQUANCY (HIGHER PART)
17A
TUNING FREQUANCY (LOWER PART)
17B
S-SYS
AFT
(auto)
17C
TUNING FREQUANCY (HIGHER PART)
17D
TUNING FREQUANCY (LOWER PART)
17E
S-SYS
AFT
(auto)
C-SYS
POS 69
C-SYS
POS 70
C-SYS
POS 71
C-SYS
POS 72
C-SYS
POS 73
C-SYS
POS 74
16-2
142
C-SYS
POS 75
C-SYS
POS 76
C-SYS
POS 77
C-SYS
POS 78
C-SYS
POS 79
C-SYS
POS 80
C-SYS
POS 81
C-SYS
POS 82
C-SYS
POS 83
C-SYS
POS 84
C-SYS
POS 85
C-SYS
POS 86
C-SYS
POS 87
16-1
(HEX)
C-SYS
POS 88
C-SYS
17F
POS 89
MODEL
MODEL
LETTER NO.
LETTER NO.
16
14A1-RU
14A2-RU
DATA
ADDRESS
(HEX)
D7
D6
D5
D4
D3
D2
D1
D0
MICON
EEPROM
EEPROM
DEFAULT
RANGE
WRITE(CPU)
180
CHASSIS
CHECK DATA
CHECK TYPE
CTV FINAL
CHECK DATA
CHECK TYPE
LAST INITIAL
SETTING DATA
REMARK
POS 89
181
TUNING FREQUANCY (HIGHER PART)
183
TUNING FREQUANCY (LOWER PART)
184
S-SYS
AFT
(auto)
185
TUNING FREQUANCY (HIGHER PART)
186
TUNING FREQUANCY (LOWER PART)
187
S-SYS
AFT
(auto)
188
TUNING FREQUANCY (HIGHER PART)
189
TUNING FREQUANCY (LOWER PART)
18A
S-SYS
AFT
(auto)
18B
TUNING FREQUANCY (HIGHER PART)
18C
TUNING FREQUANCY (LOWER PART)
18D
S-SYS
AFT
(auto)
18E
TUNING FREQUANCY (HIGHER PART)
18F
TUNING FREQUANCY (LOWER PART)
190
S-SYS
AFT
(auto)
191
TUNING FREQUANCY (HIGHER PART)
192
TUNING FREQUANCY (LOWER PART)
193
S-SYS
AFT
(auto)
194
TUNING FREQUANCY (HIGHER PART)
195
TUNING FREQUANCY (LOWER PART)
196
S-SYS
AFT
(auto)
197
TUNING FREQUANCY (HIGHER PART)
198
TUNING FREQUANCY (LOWER PART)
199
S-SYS
AFT
(auto)
19A
TUNING FREQUANCY (HIGHER PART)
19B
TUNING FREQUANCY (LOWER PART)
19C
S-SYS
AFT
(auto)
19D
TUNING FREQUANCY (HIGHER PART)
19E
TUNING FREQUANCY (LOWER PART)
19F
S-SYS
AFT
(auto)
POS 90
C-SYS
POS 91
C-SYS
POS 92
C-SYS
POS 93
C-SYS
POS 94
C-SYS
POS 95
17-2
182
C-SYS
POS 96
C-SYS
POS 97
C-SYS
POS 98
C-SYS
POS 99
C-SYS
1A0
AV1
1A1
1A2
(auto)
C-SYS
1A3
AV2
1A4
1A5
(auto)
C-SYS
1A6
1A7
1A8
1A9
1AA
1AB
1AC
1AD
1AE
1AF
1B0
1B1
1B2
1B3
1B4
1B5
1B6
1B7
1B8
17-1
1B9
1BA
1BB
1BC
1BD
1BE
1BF
MODEL
MODEL
LETTER NO.
LETTER NO.
17
14A1-RU
14A2-RU
DATA
ADDRESS
(HEX)
D7
D6
D5
D4
D3
D2
D1
D0
MICON
EEPROM
EEPROM
DEFAULT
RANGE
WRITE(CPU)
CHASSIS
CHECK DATA
CHECK TYPE
CTV FINAL
CHECK DATA
CHECK TYPE
LAST INITIAL
SETTING DATA
REMARK
1C0
1C1
1C2
1C3
1C4
1C5
1C6
1C7
1C8
1C9
1CA
1CB
1CC
1CD
1CE
1CF
18-2
1D0
1D1
1D2
1D3
1D4
1D5
1D6
1D7
1D8
1D9
1DA
1DB
1DC
1DD
1DE
1DF
1E0
1E1
1E2
1E3
1E4
1E5
1E6
1E7
1E8
1E9
1EA
1EB
1EC
1ED
1EE
1EF
1F0
1F1
1F2
1F3
1F4
1F5
1F6
1F7
1F8
18-1
1F9
1FA
1FB
1FC
1FD
1FE
1FF
MODEL
MODEL
LETTER NO.
LETTER NO.
18
Check R618 and R615.
Check D758, IC702, IC753
and D762.
Check R701, R707 and
D709.
19
Check
IC801.
19-1
Check IC651, IC751 and
IC801.
Does horizontal circuit
oscillate ?
Check
C787.
Check CRT connector K1K5 bias.
Check Secondary Main+B
(Approx. 115V)
Check T701 pin (7) voltage
(Approx. 310V at 220V AC)
Check F701.
NO RASTER
Replace the fuse.
Blown out.
Checking the
protector circuit.
D1001 (Power LED Red)
turns on or turns ON/OFF.
D1001 (Power LED Green)
turns on.
Check IC701, D701 and
C707.
The fuse is again blown out.
TROUBLE SHOOTING TABLE
19-2
Check P301 connector of
IC301 and peripheral circuit.
Does signal appear at pins
(6) and (8) of IC301 ?
Check Q205 and
related circuit.
Check IC801 and
its related circuit.
CheckIC801.
Check Q301, pins(4) and (6)
of IC801 and peripheral
circuit.
Check C356 and
its peripheral
circuit.
Does signal appear at pins(28)
and (29) of IC801?
Check pin (1) of
SF201 and Tuner
related circuit.
Check pin (37)of
IC801 and related
circuit.
Does noise or
signal appear at
pin (38) of IC801 ?
NO SOUND
Does noise signal appear at
pin (44) of IC801 ?
Check pin (27) of
IC801, Tuner and
related circuit.
CIRCUITS TO BE CHECKED:
» Sound system pins (28)
and (44) of IC801.
» Sound Detector Circuit.
» Sound Switch and Att.
Control.
» Audio Output Circuit.
Check pin(38) of
IC801.
Check the tuner AGC
(TP201).
Check the tuner supply voltage LB must
be approx. 5V. BT must be approx, 32V.
And CH preset data check.
No snow noise.
Does noise or signal appear at pin (40)
of IC801 ?
Does the noise level increase at max.
Contrast, Brightness and Sound controls ?
NO PICTURE, NO SOUND
Noise increases but no signal is
received.
CIRCUITS TO BE CHECKED:
» Tuner.
» PIF.
» Automatic Gain Control.
» (5V), (32V) Power Source.
TROUBLE SHOOTING TABLE (Continued)
14A1-RU
14A2-RU
20
Check C503 and C507.
20-1
Check IC501.
Check IC501.
NO VERTICAL SCAN
Check R504, R503, R506,
R513, C517 and D501.
Vertical linearity and size is
abnormal.
Readjust vertical size.
(Bas Data)
DEFECTIVE VERTICAL AMP.
AND VERTICAL LINEARITY
Check pins(16), (17) and
(34) of IC801.
NO SPECIFIC COLOUR
Check Q870, Q885 and their
adjacent circuits.
The picture colour is magenta.
Check Q872, Q887 and their
adjacent circuits.
The picture colour is yellow.
Readjust the white balance.
Is the white balance properly
adjusted ?
20-2
Check X1001.(12MHz)
Check IC801 and bias
control circuit.
“PAL”/“SECAM”
(NO COLOUR SYNCHRONIZATION)
Check Q871, Q883 and their
adjacent circuits.
The picture colour is cyan.
Check IC801, R801, R802,
R803, D804, D805, D806
and Q801.
Is some colour produced in
B/W broadcast reception ?
NO SPECIFIC COLOUR
NEITHER VERTICAL NOR
HORIZONTAL SYNCHRONIZATION
CIRCUIT TO BE CHECKED:
» Sync. Separator Circuit.
TROUBLE SHOOTING TABLE (Continued)
TROUBLE SHOOTING TABLE (Continued)
14A1-RU
14A2-RU
Input 1,3,7,9 by R/C key.
Set vol up/down by R/C key.
#1 Ch 1 is your selected channel
for hotel mode.
21
21-1
When using hotel mode, user can control "contrast", "brightness", "sharpness" and "tint" function.
But after power off, it will return to the initial setting.
You can't use:-Preset mode
Fine tuning
Skip mode
System selection
The others function is allowed to be used.
CONDITION:
* We recommend
Before set the hotel mode, it is better to choose ch 1 & set s-vol level Up to 75% full scale.
After set hotel mode, starting channel will be always ch 1 & maximum sound level out will be set the half of
full scale.
* If you set hotel mode in AV, starting channel will be the last ch which you received before power off (same as
normal operation)
HOTEL ON
PASSWORD ****
b) Key in the four digits password starting with number "1", "3", "7", "9", then the hotel mode will be enable,
you can switch on/off the hotel mode by using R/C (volume up/down) {3} key.
Ans: a) Press the R/C (FUNCTION) {1} key until language selection appear, within five second press the (one/two
digit) {2} key and keep pressing it for five second, then you can see the hotel mode with four digits password.
How to enable/disable the "Hotel Mode" ?
UA1 HOTEL MODE APPLICATION
21-2
14A1-RU
14A2-RU
14A1-RU
14A2-RU
SOLID STATE DEVICE BASE DIAGRAM
TOP VIEW
8
5
4
COLLECTOR
COLLECTOR
3
:BG:
2R
1
4
1
M24C04W
BASE
2
BASE
EMITTER
2R
EMITTER
BASE
B709A
D601A
EMITTER
2SC2735
22-2
FX0008GE
COLLECTOR
iX3368CE
SIDE VIEW
+
BASE
COLLECTOR
EMITTER
1 2 3
BASE
COLLECTOR
EMITTER
2SC1815
1
~
-
3
SE115N
PST573J
~
DX0386CE
2SC2482
ANODE
(RED)
CATHODE
(COMMON)
ANODE
(GREEN)
1
12
1 2 3
TDA7056A
C
E
KA7808
KA7805
PX0423CE
22-1
B
2SD1877
2SD2586
8
1
1
2
3
5
1
TA48M033
STRF6653
STRF6654
LA7016
22
1
3
4 6 8
5 7
TDA8357
9
14A1-RU
14A2-RU
23-1
23-2
WAVEFORMS
23
14A1-RU
14A2-RU
MODEL 14A1-RU CHASSIS LAYOUT
J
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
24
7
8
9
10
14A1-RU
14A2-RU
MODEL 14A2-RU CHASSIS LAYOUT
J
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
25
7
8
9
10
14A1-RU
14A2-RU
DESCRIPTION OF SCHEMATIC DIAGRAM
SAFETY NOTES:
NOTES:
1. DISCONNECT THE AC PLUG FROM THE AC OUTLET BEFORE
REPLACING PARTS.
2. SEMICONDUCTOR HEAT SINKS SHOULD BE REGARDED AS
POTENTIAL SHOCK HAZARDS WHEN THE CHASSIS IS OPERATING.
1. The unit of resistance "ohm" is omitted.
(K = 1000 ohms, M = Mega ohm).
2. All resistors are 1/8 watt, unless otherwise noted.
3. All capacitors are µF, unless otherwise noted. (P = µµF).
IMPORTANT SAFETY NOTICE:
VOLTAGE MEASUREMENT CONDITIONS:
PARTS MARKED WITH " å " (
) ARE IMPOTANT FOR
MAINTAINING THE SAFETY OF THE SET. BE SURE TO REPLACE
THESE PARTS WITH SPECIFIED ONES FOR MAINTAINING THE
SAFETY AND PERFORMANCE OF THE SET.
1. Voltages in parenthesis measured with no signal.
2. Voltages without parenthesis measured with 3mV B & W or Colour signal.
3. All the voltages in each point are measured with VTVM.
SERVICE PRECAUTION:
THE AREA ENCLOSED BY THIS LINE ( —– - —– ) IS DIRECTLY
CONNECTED WITH AC MAINS VOLTAGE.
WHEN SERVICING THE AREA, CONNECT AN ISOLATING TRANSFORMER BETWEEN TV RECEIVER AND AC LINE TO ELIMINATE
HAZARD OF ELECTRIC SHOCK.
WAVEFORM MEASUREMENT CONDITIONS:
1. The colour bar generator signal of 1.0V peak applied at pin (24)
of IC201.
2. Approximately 4V AGC bias .
26
14A1-RU
14A2-RU
SCHEMATIC DIAGRAM: CRT Unit
J
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
27
7
8
9
10
14A1-RU
14A2-RU
14A1-RU
14A2-RU
SCHEMATIC DIAGRAM: MODEL 14A1-RU MAIN Unit
J
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
28
7
8
9
10
11
12
13
14
15
29
16
17
18
19
14A1-RU
14A2-RU
14A1-RU
14A2-RU
SCHEMATIC DIAGRAM: MODEL 14A2-RU MAIN Unit
J
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
30
7
8
9
10
11
12
13
14
15
31
16
17
18
19
14A1-RU
14A2-RU
14A1-RU
14A2-RU
BLOCK DIAGRAM - 1/3:MODEL 14A1-RU MAIN Unit
J
PWB-A: MAIN Unit
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
32
7
8
9
10
11
12
13
14
15
33
16
17
18
19
14A1-RU
14A2-RU
14A1-RU
14A2-RU
BLOCK DIAGRAM - 2/3:MODEL 14A2-RU MAIN Unit
J
PWB-A: MAIN Unit
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
34
7
8
9
10
11
12
13
14
15
35
16
17
18
19
14A1-RU
14A2-RU
BLOCK DIAGRAM - 3/3:CRT Unit
J
PWB-B: CRT Unit
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
36
7
8
9
10
14A1-RU
14A2-RU
PRINTED WIRING BOARD ASSEMBLIES
PWB-B: CRT Unit (Wiring Side)
J
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
37
7
8
9
10
14A1-RU
14A2-RU
14A1-RU
14A2-RU
PWB-A: MAIN Unit (Wiring Side)
J
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
38
7
8
9
10
11
12
13
14
15
39
16
17
18
19
14A1-RU
14A2-RU
14A1-RU
14A2-RU
PWB-A: MAIN Unit (Component Side)
J
I
H
G
F
E
D
C
B
A
1
2
3
4
5
6
40
7
8
9
10
11
12
13
14
15
41
16
17
18
19
14A1-RU
14A2-RU
Ref. No.
Part No.
Description
Code
Ref. No.
PARTS REPLACEMENT
Replacement parts which have these special safety characteristics
are identified in this manual; electrical components having such
features are identified by "å" in the Replacement Parts Lists.
The use of a substitute replacement part which does not have the
same safety characteristics as the factory recommended replacement parts shown in this service manual may create shock, fire or
other hazards.
"HOW TO ORDER REPLACEMENT PARTS"
Q201
Q203
Q205
Q301
Q302
Q305
Q601
Q602
Q603
Q723
Q752
Q753
Q801
Q802
Q1003
Q1010
VS2SC2735//1E
VS2SD601A//-1
VS2SC3198-G-1
VS2SD601A//-1
VS2SD601A//-1
VS2SD601A//-1
VS2SC2482//-1
VS2SD1877//1E
VS2SD601A//-1
VS2SD601A//-1
VS2SC3198-G-1
VS2SC3198-G-1
VS2SB709A//-1
VS2SB709A//-1
VS2SD601A//-1
VS2SD601A//-1
D201
D301
D305
D308
D310
D311
D401
D402
D501
D502
D503
D504
D505
D507
D508
D509
D510
D511
D512
D513
D514
D515
D602
D603
D604
D605
D606
D607
D608
D609
D610
D611
D612
D613
D614
D701
D702
D705
D706
D707
D708
D709
D710
D711
D713
D750
D752
D753
D758
D760
D763
D801
D802
D803
D804
D805
RH-EX0676GEZZ
RH-DX0475CEZZ
RH-EX0631GEZZ
RH-EX0631GEZZ
RH-DX0302CEZZ
VHDRL3Z////-1
RH-EX0631GEZZ
RH-EX0631GEZZ
RH-EX0640GEZZ
RH-DX0475CEZZ
RH-DX0475CEZZ
RH-DX0475CEZZ
RH-DX0127CEZZ
RH-DX0475CEZZ
RH-EX0647GEZZ
RH-EX0647GEZZ
RH-EX0867CEZZ
RH-EX0867CEZZ
RH-DX0475CEZZ
RH-DX0475CEZZ
RH-EX0903CEZZ
RH-EX0903CEZZ
RH-DX0475CEZZ
RH-DX0131CEZZ
RH-DX0475CEZZ
RH-EX0840CEZZ
RH-DX0475CEZZ
RH-EX0662GEZZ
RH-EX0604GEZZ
RH-DX0475CEZZ
RH-EX0662GEZZ
RH-DX0302CEZZ
RH-EX0627GEZZ
RH-DX0475CEZZ
RH-DX0475CEZZ
RH-DX0386CEZZ
VHD1SS82///1A
RH-DX0492CEZZ
VHD1SS82///1A
VHD1SS82///1A
RH-DX0400CEZZ
RH-DX0164CEZZ
RH-EX0601GEZZ
VHD1SS82///1A
RH-EX0621GEZZ
RH-DX0475CEZZ
RH-DX0475CEZZ
RH-DX0471CEZZ
RH-DX0461CEZZ
RH-DX0475CEZZ
RH-DX0475CEZZ
RH-DX0475CEZZ
RH-DX0475CEZZ
RH-DX0475CEZZ
RH-DX0475CEZZ
RH-DX0475CEZZ
To have your order filled promptly and correctly, please furnish the
following informations.
MARK
Ref. No.
: SPARE PARTS-DELIVERY SECTION.
Description
Code
PICTURE TUBE
å V1
å
VB37GDA86X/1E
QEARC1422PEZZ
RCiLG0068PEZZ
RCiLH0149PEZZ
PMAGF3045CEZZ
LHLDP1066PE00
R
R
R
R
R
R
Picture Tube
Grounding Strap
Degaussing Coil
Deflection Yoke
Magnet
Holder
CB
AD
AH
BA
AG
AC
PRINTED WIRING BOARD ASSEMBLY
(NOT REPLACEMENT ITEM)
PWB-A DUNTK9988WEV4 - Main Unit (14A1-RU)
PWB-A DUNTK9988WEV8 - Main Unit (14A2-RU)
PWB-B DUNTK9990WEV4 - CRT Unit
PWB-A
—
—
—
DUNTK9988WEV4/V8
MAIN UNIT
TUNER AND ASSEMBLY
NOTE: THE PARTS HERE SHOWN ARE SUPPLIED AS AN
ASSEMBLY BUT INDEPENDENTLY.
å TU201 VTUVTST5HD84/ R VHF Tuner
BB
INTEGRATED CIRCUITS
IC301
IC304
IC402
IC501
IC605
IC701
IC751
IC753
IC801
IC1002
IC1003
IC1005
VHiTDA7056A-1
VHiLA7016//-1
VHiLA7016//-1
VHiTDA8357/-1
VHiKA7808AP-1
VHiSTRF6653-1
VHiTA48M033-1
VHiSE115N//-1
RH-iX3368CEN3
VHiPST573J/-1
VHiM24C04W/-1
VHiKA7805AP-1
R
R
R
R
R
R
R
R
R
R
R
R
TDA7056A
LA7016
LA7016
TDA8357J/N1/S1
KIA7808API
I.C.
TA48M033F
SE115N
I.C.
I.C.
I.C.
KIA7805API
Code
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
2SC2735
2SD601A
2SC3198-G
2SD601A
2SD601A
2SD601A
2SC2482
2SD1877
2SD601A
2SD601A
2SC3198-G
2SC3198-G
2SB709A
2SB709A
2SD601A
2SD601A
AC
AC
AA
AC
AC
AC
AD
AL
AC
AC
AA
AA
AA
AA
AC
AC
DIODES
2. REF. NO.
4. DESCRIPTION
Part No.
Description
TRANSISTORS
PARTS LIST
1. MODEL NUMBER
3. PART NO.
Part No.
AP
AH
AH
AN
AE
AS
AH
AF
BC
AE
AG
AE
42
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Zener Diode
Diode
Zener Diode
Zener Diode
Diode (14A1-RU)
Diode (14A2-RU)
Zener Diode
Zener Diode
Zener Diode
Diode
Diode
Diode
Diode
Diode
Zener Diode
Zener Diode
Zener Diode
Zener Diode
Diode
Diode
Zener Diode
Zener Diode
Diode
Diode
Diode
Zener Diode
Diode
Zener Diode
Zener Diode
Diode
Zener Diode
Diode
Zener Diode
Diode
Diode
Diode
1SS82
Diode
1SS82
1SS82
Diode
Diode
Zener Diode
1SS82
Zener Diode
Diode
Diode
Diode
Diode
Diode
Diode
Diode
Diode
Diode
Diode
Diode
AA
AB
AA
AA
AC
AE
AA
AA
AA
AB
AB
AB
AC
AB
AA
AA
AC
AC
AB
AB
AC
AC
AB
AC
AB
AC
AB
AB
AB
AB
AB
AC
AA
AB
AB
AG
AC
AE
AC
AC
AC
AC
AA
AC
AB
AB
AB
AE
AG
AB
AB
AB
AB
AB
AB
AB
14A1-RU
14A2-RU
Ref. No.
D806
D1001
D1004
D1007
D1008
D1009
D1010
D1011
å IC702
Part No.
Description
RH-DX0475CEZZ
RH-PX0423CEZZ
RH-DX0475CEZZ
RH-EX0867CEZZ
RH-EX0867CEZZ
RH-EX0867CEZZ
RH-EX0867CEZZ
RH-EX0627GEZZ
RH-FX0008GEZZ
R
R
R
R
R
R
R
R
R
Diode
PhotoDiode
Diode
Zener Diode
Zener Diode
Zener Diode
Zener Diode
Zener Diode(14A2-RU)
PC123FY8
Code
Ref. No.
AB
AD
AB
AC
AC
AC
AC
AA
AE
C356
C359
C360
C364
C371
C373
C374
C375
C379
C390
C405
C406
C407
C408
C409
C410
C411
C469
C501
C502
C503
C504
C506
C507
C508
C512
C513
C514
C515
C516
C517
C601
C602
C603
C604
C605
C606
C607
C608
C609
C610
C611
C612
C613
C614
C615
C616
C617
C620
C623
C624
C625
C626
C627
C628
C650
C654
C700
å C701
C702
C703
C704
C705
C707
C708
C709
C711
C712
C713
C714
C715
C716
C717
C718
å C721
C752
PACKAGED CIRCUITS
å VA700 RH-VX0047CEZZ R Varistor
PR702 RMPTP0028CEZZ R Packaged Circuit
X1001 RCRSB0281CEZZ R Crystal
AF
AG
AG
COILS
L202
L203
L204
L205
L207
L208
L209
L301
L401
L601
L603
å L701
å L702
L802
L803
L1030
L1050
L1051
VP-DF270K0000
VP-DF270K0000
VP-XF1R2K0000
VP-DF1R0K0000
VP-DF1R0K0000
VP-XF100K0000
VP-XF6R8K0000
VP-DF1R0K0000
VP-DF1R0K0000
VP-CF1R0M0000
RCiLP0225CEZZ
RCiLF0021PEZZ
RCiLF0036PEZZ
VP-DF100K0000
VP-DF100K0000
VP-DF100K0000
VP-DF100K0000
VP-DF100K0000
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Peaking
Peaking
Peaking
Peaking
Peaking
Peaking
Peaking
Peaking
Peaking
Peaking
Coil
Coil
Coil
Peaking
Peaking
Peaking
Peaking
Peaking
27µH
27µH
1.2µH
1µH
1µH
10µH
6.8µH
1µH
1µH
1µH
10µH
10µH
10µH
10µH
10µH
AB
AB
AB
AB
AB
AB
AB
AB
AB
AB
AF
AK
AN
AB
AB
AB
AB
AB
FILTER
CF201 RFiLC0024CEZZ
CF202 RFiLC0318CEZZ
SF201 RFiLC0442CEZZ
R Filter
R Filter
R Filter
AE
AG
AL
TRANSFORMERS
å T602
å T603
å T701
RTRNF0187PEZZ R H-VOLT Transformer
RTRNZ0179CEZZ R Transformer
RTRNZ0180PEZZ R Transformer
AY
AE
AN
CAPACITORS
C200
C203
C204
C205
C206
C207
C208
C209
C210
C211
C212
C213
C215
C216
C217
C302
C303
C304
C305
C312
C314
C315
C317
C318
C331
C332
C333
VCEA0A1CW476M
VCKYCY1HF103Z
VCEA0A1CW107M
VCKYCY1HF103Z
VCEA0A1HW106M
VCKYCY1HF103Z
VCKYCY1HF103Z
VCKYCY1HF103Z
VCKYCY1HF103Z
VCKYCY1EF104Z
VCEA0A1CW106M
VCKYCY1HF223Z
VCEA0A1CW476M
VCKYCY1HB821K
VCKYCY1HB472K
VCEA0A1HW225M
VCEA0A1CW106M
VCQYTA1HM473J
VCQYTA1HM473J
VCQYTA1HM123J
VCEA0A1EW477M
VCKYPA1HF103Z
VCEA0A1HW224M
VCKYCY1HB102K
VCEA0A1HW105M
VCEA0A1EW477M
VCKYPA2HB102K
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
47
0.01
100
0.01
10
0.01
0.01
0.01
0.01
0.1
10
0.022
47
820p
4700p
2.2
10
0.047
0.047
0.012
470
0.01
0.22
1000p
1
470
1000p
16V
50V
16V
50V
50V
50V
50V
50V
50V
25V
16V
50V
16V
50V
50V
50V
16V
50V
50V
50V
25V
50V
50V
50V
50V
25V
500V
Electrolytic
Ceramic
Electrolytic
Ceramic
Electrolytic
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Electrolytic
Ceramic
Electrolytic
Ceramic
Ceramic
Electrolytic
Electrolytic
Mylar
Mylar
Mylar
Electrolytic
Ceramic
Electrolytic
Ceramic
Electrolytic
Electrolytic
Ceramic
AB
AA
AC
AA
AB
AA
AA
AA
AA
AA
AB
AB
AB
AA
AA
AB
AB
AA
AA
AA
AD
AA
AB
AA
AB
AD
AA
43
Part No.
VCKYCY1HB682K
VCEA9M1CW106M
VCEA9M1HW225M
VCEA0A1CW106M
VCEA0A1CW476M
VCEA0A1CW107M
VCEA0A1HW225M
VCEAEA1HW225M
VCEA0A1HW335M
VCEA0A1HW105M
VCEA0A1CW107M
VCEA0A1CW477M
VCEA0A1CW106M
VCEA0A1CW106M
VCKYCY1EF104Z
VCKYCY1EF104Z
VCKYCY1HB102K
VCEA0A1HW105M
VCKYCY1HF103Z
VCKYCY1HF103Z
VCEA0A1EW108M
VCKYCY1HF223Z
VCQYTA1HM104J
VCEA0A1JW107M
VCQYTA1HM103J
VCKYCY1HB102K
VCKYCY1HB102K
VCKYPA1HF103Z
VCKYPA2HB102K
VCEA0A1JW477M
VCQYTA1HM104J
VCEAGA2EW106M
VCQYTA1HM104J
VCEA0A1HW105M
VCEA0A1HW105M
VCKYPA1HF103Z
VCKYCY1HF103Z
VCEA0A1CW477M
VCEA0A1EW476M
VCEA0A1EW108M
VCFYSB2EB823J
VCKYPA2HB102K
RC-EZ0724CEZZ
VCFPVC2DB394J
RC-KZ0035CEZZ
VCFPVC2DB224J
VCFPPD3CA622H
VCKYPA2HB102K
VCKYCY1EF104Z
VCQYTA1HM222J
VCQYTA1HM472J
VCEA0A1HW105M
VCKYCY1HF223Z
VCEA0A1HW106M
VCEA0A1HW224M
VCKYCY1EF104Z
VCEA0A1CW476M
VCQYTA1HM103J
RC-FZ033SCEZZ
RC-KZ0160GEZZ
RC-KZ0160GEZZ
VCKYPA2HB102K
VCKYPA2HB102K
RC-EZ1044CEZZ
RC-KZ0160GEZZ
RC-QZA471TAYJ
RC-KZ0339CEZZ
VCQYTA1HM102J
RC-KZ007JCEZZ
RC-KZ0338CEZZ
VCKYPA2HB102K
VCEA0A1EW107M
VCQYTA1HM182J
VCEAGA2AW475M
RC-KZ0106GEZZ
VCEA0A0JW107M
Description
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
6800p 50V Ceramic
10
16V Electrolytic
2.2
50V Electrolytic
10
16V Electrolytic
47
16V Electrolytic
100
16V Electrolytic
2.2
50V Electrolytic
2.2
50V Electrolytic
3.3
50V Electrolytic
1
50V Electrolytic
100
16V Electrolytic
470
16V Electrolytic
10
16V Electrolytic
10
16V Electrolytic
0.1
25V Ceramic
0.1
25V Ceramic
1000p 50V Ceramic
1
50V Electrolytic
0.01 50V Ceramic
0.01 50V Ceramic
1000 25V Electrolytic
0.022 50V Ceramic
0.1
50V Mylar
100
63V Electrolytic
0.01 50V Mylar
1000p 50V Ceramic
1000p 50V Ceramic
0.01 50V Ceramic
1000p 500V Ceramic
470
63V Electrolytic
0.1
50V Mylar
10
250V Electrolytic
0.1
50V Mylar
1
50V Electrolytic
1
50V Electrolytic
0.01 50V Ceramic
0.01 50V Ceramic
470
16V Electrolytic
47
25V Electrolytic
1000 25V Electrolytic
0.082 250V M.Polypro
1000p 500V Ceramic
100
160V Electrolytic
0.39 200V M.Polypro
Capacitor
0.22 200V M.Polypro
6200p 1600V M.Polypro
1000p 500V Ceramic
0.1
25V Ceramic
2200p 50V Mylar
4700p 50V Mylar
1
50V Electrolytic
0.022 50V Ceramic
10
50V Electrolytic
0.22 50V Electrolytic
0.1
25V Ceramic
47
16V Electrolytic
0.01 50V Mylar
0.047 AC250V M.Polypro
0.01 250V Ceramic
0.01 250V Ceramic
1000p 500V Ceramic
1000p 500V Ceramic
150
400V Electrolytic
0.01 250V Ceramic
470p 50V Mylar
680p 2kV Ceramic
1000p 50V Mylar
0.01 250V Ceramic
560p 2kV Ceramic
1000p 500V Ceramic
100
25V Electrolytic
1800p 50V Mylar
4.7
100V Electrolytic
3300p 2kV Ceramic
100
6.3V Electrolytic
Code
AA
AB
AB
AB
AB
AC
AB
AB
AB
AB
AC
AC
AB
AB
AA
AA
AA
AB
AA
AA
AD
AB
AA
AC
AA
AA
AA
AA
AA
AE
AA
AC
AA
AB
AB
AA
AA
AC
AB
AD
AD
AA
AG
AE
AB
AE
AE
AA
AA
AA
AB
AB
AB
AB
AB
AA
AB
AA
AF
AC
AC
AA
AA
AM
AC
AB
AD
AA
AC
AD
AA
AC
AA
AB
AG
AB
14A1-RU
14A2-RU
Ref. No.
C753
C754
C755
å C759
C760
C761
C762
C801
C802
C803
C804
C805
C806
C807
C808
C809
C810
C811
C812
C813
C814
C1001
C1003
C1004
C1005
C1006
C1007
C1008
C1009
C1010
C1011
C1012
C1013
C1014
C1015
C1016
C1018
C1019
Part No.
VCKYPA2HB102K
VCEA0A1CW476M
VCEA0A1CW108M
VCKYPA1HB102K
RC-KZ0339CEZZ
RC-EZ0724CEZZ
VCQYTA1HM473J
VCEA0A1HW105M
VCEA0A1CW337M
VCEA9M1CW107M
VCKYCY1HB222K
VCKYCY1HB102K
VCKYCY1HB102K
VCKYCY1HB102K
VCEA0A1CW107M
VCKYCY1HF223Z
VCKYCY1EF104Z
VCEA0A1CW107M
VCFYFA1HA224J
VCFYFA1HA224J
VCKYCY1HB471K
VCEA0A0JW107M
VCEA0A1CW106M
VCKYCY1CF474Z
VCKYCY1HF223Z
VCEA0A1CW106M
VCEA0A1CW106M
VCCCCY1HH330J
VCCCCY1HH330J
VCEA0A0JW107M
VCKYCY1HF223Z
VCKYCY1HF223Z
VCEA0A0JW107M
VCEA0A1CW106M
VCFYFA1HA474J
VCQYTA1HM104J
VCKYCY1HB221K
VCEA9M1HW225M
Description
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
1000p 500V
47
16V
1000 16V
1000p 50V
680p 2kV
Capacitor
0.047 50V
1
50V
330
16V
100
16V
2200p 50V
1000p 50V
1000p 50V
1000p 50V
100
16V
0.022 50V
0.1
25V
100
16V
0.22 50V
0.22 50V
470p 50V
100
6.3V
10
16V
0.47 16V
0.022 50V
10
16V
10
16V
33p
50V
33p
50V
100
6.3V
0.022 50V
0.022 50V
100
6.3V
10
16V
0.47 50V
0.1
50V
220p 50V
2.2
50V
Code
Ref. No.
Mylar
Electrolytic
Electrolytic
Electrolytic
Ceramic
Ceramic
Ceramic
Ceramic
Electrolytic
Ceramic
Ceramic
Electrolytic
M.Polypro
M.Polypro
Ceramic
Electrolytic
Electrolytic
Ceramic
Ceramic
Electrolytic
Electrolytic
Ceramic
Ceramic
Electrolytic
Ceramic
Ceramic
Electrolytic
Electrolytic
M.Polypro
Mylar
Ceramic
Electrolytic
AA
AB
AD
AA
AD
AG
AA
AB
AC
AB
AA
AA
AA
AA
AC
AB
AA
AC
AB
AB
AA
AB
AB
AB
AB
AB
AB
AA
AA
AB
AB
AB
AB
AB
AC
AA
AA
AB
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
RJ85
RJ87
RJ88
RJ89
RJ92
RJ94
RJ96
RJ97
RJ100
RJ103
RJ105
RJ201
RJ202
RJ204
RJ205
RJ206
R201
R202
R203
R204
R205
R206
R207
R208
R209
R217
R218
R219
R220
R221
R222
R226
R227
R228
R230
R231
R232
R233
R237
R238
R239
R302
R303
R304
R305
R307
R308
R320
R321
R328
R329
R330
R331
R332
R333
R334
R341
R342
R343
R344
R357
R378
R403
R404
R406
R407
R411
R412
R501
R502
R503
R504
R505
R506
R508
R509
Ceramic
Electrolytic
Electrolytic
Ceramic
Ceramic
RESISTORS
RJ2
RJ5
RJ9
RJ10
RJ11
RJ12
RJ13
RJ15
RJ16
RJ21
RJ25
RJ26
RJ27
RJ29
RJ30
RJ31
RJ32
RJ33
RJ34
RJ41
RJ43
RJ51
RJ53
RJ61
RJ64
RJ66
RJ68
RJ69
RJ71
RJ74
RJ75
RJ76
RJ78
RJ79
RJ80
RJ84
VRN-MD2AL000J
VRN-MD2AL000J
VRN-MD2AL000J
VRN-MD2AL000J
VRN-MD2AL000J
VRN-MD2AL000J
VRN-MD2AL000J
VRN-MD2AL000J
VRN-MD2AL000J
VRN-MD2AL000J
VRN-MD2AL000J
VRN-MD2AL000J
VRN-MD2AL000J
VRN-MD2AL000J
VRN-MD2AL000J
VRN-MD2AL000J
VRN-MD2AL000J
VRN-MD2AL000J
VRN-MD2AL000J
VRN-MD2AL000J
VRN-MD2AL000J
VRN-MD2AL000J
VRN-MD2AL000J
VRN-MD2AL000J
VRN-MD2AL000J
VRN-MD2AL000J
VRN-MD2AL000J
VRN-MD2AL000J
VRN-MD2AL000J
VRN-MD2AL000J
VRN-MD2AL000J
VRN-MD2AL000J
VRN-MD2AL000J
VRN-MD2AL000J
VRN-MD2AL000J
VRN-MD2AL000J
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
44
Part No.
VRN-MD2AL000J
VRN-MD2AL000J
VRN-MD2AL000J
VRN-MD2AL000J
VRN-MD2AL000J
VRN-MD2AL000J
VRN-MD2AL000J
VRN-MD2AL000J
VRN-MD2AL000J
VRN-MD2AL000J
VRN-MD2AL000J
VRN-MD2AL000J
VRN-MD2AL000J
VRN-MD2AL000J
VRN-MD2AL000J
VRN-MD2AL000J
VRN-MD2AL101J
VRN-MD2AL101J
VRD-RM2HD102J
VRD-RM2HD102J
VRD-RA2BE680J
VRN-MD2AL122J
VRN-MD2AL221J
VRN-MD2AL122J
VRN-MD2AL392J
VRD-RA2BE392J
VRN-MD2AL102J
VRN-MD2AL391J
VRN-MD2AL101J
VRN-MD2AL102J
VRN-MD2AL681J
VRN-MD2AL750J
VRD-RM2HD330J
VRD-RM2HD330J
VRN-MD2AL101J
VRN-MD2AL153J
VRD-RA2BE680J
VRN-MD2AL181J
VRN-MD2AL272J
VRN-MD2AL821J
VRN-MD2AL221J
VRN-MD2AL473J
VRN-MD2AL473J
VRN-MD2AL392J
VRN-MD2AL100J
VRD-RA2BE182J
VRD-RA2BE472J
VRN-MD2AL101J
VRN-MD2AL561J
VRN-MD2AL564J
VRN-MD2AL332J
VRN-MD2AL101J
VRN-MD2AL102J
VRN-MD2AL561J
VRN-MD2AL103J
VRN-MD2AL102J
VRN-MD2AL332J
VRN-MD2AL564J
VRN-MD2AL104J
VRN-MD2AL101J
VRN-MD2AL100J
VRN-VV3DBR68J
VRN-MD2AL101J
VRD-RA2BE820J
VRN-MD2AL103J
VRN-MD2AL101J
VRD-RA2BE820J
VRN-MD2AL101J
VRN-MD2AL182J
VRN-MD2AL182J
VRD-RM2HD2R2J
VRD-RM2HD150J
VRG-PD2HD330J
VRD-RA2BE124J
VRD-RM2HD221J
VRD-RM2HD1R0J
Description
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
100
100
1k
1k
68
1.2k
220
1.2k
3.9k
3.9k
1k
390
100
1k
680
75
33
33
100
15k
68
180
2.7k
820
220
47k
47k
3.9k
10
1.8k
4.7k
100
560
560k
3.3k
100
1k
560
10k
1k
3.3k
560k
100k
100
10
0.68
100
82
10k
100
82
100
1.8k
1.8k
2.2
15
33
120k
220
1
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/2W
1/2W
1/8W
1/10W
1/10W
1/10W
1/10W
1/8W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/2W
1/2W
1/10W
1/10W
1/8W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/8W
1/8W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
1/10W
2W
1/10W
1/8W
1/10W
1/10W
1/8W
1/10W
1/10W
1/10W
1/2W
1/2W
1/2W
1/8W
1/2W
1/2W
Code
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Carbon
Carbon
Carbon
Metal Film
Metal Film
Metal Film
Metal Film
Carbon
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Carbon
Carbon
Metal Film
Metal Film
Carbon
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Carbon
Carbon
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Carbon
Metal Film
Metal Film
Carbon
Metal Film
Metal Film
Metal Film
Carbon
Carbon
Fuse Resistor
Carbon
Carbon
Carbon
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AC
AA
AA
AA
14A1-RU
14A2-RU
Ref. No.
Part No.
Description
R510
R511
R513
R514
R515
R516
R602
R603
R604
R605
R607
R608
R609
R610
R611
R612
R613
R614
R615
R616
R617
R618
R619
R624
R625
R626
R627
R628
R630
R631
R632
R633
R635
R636
R637
R638
R701
VRN-MD2AL101J
VRN-MD2AL101J
VRD-RA2BE393J
VRN-MD2AL101J
VRN-MD2AL272J
VRD-RM2HD223J
VRN-VV3AB1R5J
VRD-RM2HD102J
VRD-RA2BE393J
VRD-RM2HD101J
VRN-MD2AL102J
VRN-MD2AL123J
VRD-RA2BE273G
VRD-RA2BE153J
VRD-RA2EE823G
VRD-RA2BE103J
VRD-RA2BE103J
VRN-MD2AL103J
VRS-KT3LB332J
VRN-MD2AL102J
VRD-RM2HD472J
VRS-KA3HG4R7K
VRD-RM2HD682J
VRD-RA2BE101J
VRN-MD2AL184J
VRN-MD2AL472J
VRD-RM2HD4R7J
VRD-RM2HD470J
VRN-MD2AL100J
VRN-MD2AL391J
VRN-MD2AL273J
VRN-MD2AL102J
VRN-MD2AL822J
VRN-MD2AL223J
VRD-RM2HD391J
VRN-MD2AL333J
VRW-KQ3NC3R9K
R701
VRW-KQ3NC3R3K R
R703
R705
R706
R707
R708
R709
R710
R711
å R712
R717
R718
å R719
R721
R722
R723
å R726
R728
R750
R755
R756
R758
R759
R760
R761
R764
R766
R801
R802
R803
R804
R805
R806
R807
R808
R809
R812
VRS-KT3LB473J
VRD-RA2BE122J
VRD-RM2HD152J
VRS-KT3LB473J
VRD-RM2HD272J
VRD-RA2BE681J
VRN-VV3ABR39J
VRN-VV3ABR33J
VRG-PD2HD4R7J
VRD-RM2HD124J
VRD-RM2HD124J
VRC-UA2HG825K
VRD-RA2BE393J
VRD-RM2HD124J
VRD-RA2BE684J
VRC-UA2HG825K
VRN-MD2AL272J
VRD-RM2HD4R7J
VRD-RA2BE222J
VRN-MD2AL152J
VRD-RA2BE102J
VRN-MD2AL102J
VRD-RA2BE471J
VRD-RA2BE221J
VRN-MD2AL272J
VRD-RM2HD680J
VRN-MD2AL101J
VRN-MD2AL101J
VRN-MD2AL101J
VRN-MD2AL101J
VRN-MD2AL822J
VRD-RA2BE123J
VRN-MD2AL103J
VRN-MD2AL221J
VRD-RA2BE224J
VRN-MD2AL101J
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
100 1/10W
100 1/10W
39k 1/8W
100 1/10W
2.7k 1/10W
22k 1/2W
1.5 1W
1k
1/2W
39k 1/8W
100 1/2W
1k
1/10W
12k 1/10W
27k 1/8W
15k 1/8W
82k 1/4W
10k 1/8W
10k 1/8W
10k 1/10W
3.3k 3W
1k
1/10W
4.7k 1/2W
4.7 5W
6.8k 1/2W
100 1/8W
180k 1/10W
4.7k 1/10W
4.7 1/2W
47
1/2W
10
1/10W
390 1/10W
27k 1/10W
1k
1/10W
8.2k 1/10W
22k 1/10W
390 1/2W
33k 1/10W
3.9 7W
(14A1-RU)
3.3 7W
(14A2-RU)
47k 3W
1.2k 1/8W
1.5k 1/2W
47k 3W
2.7k 1/2W
680 1/8W
0.39 1W
0.33 1W
4.7 1/2W
120k 1/2W
120k 1/2W
8.2M 1/2W
39k 1/8W
120k 1/2W
680k 1/8W
8.2M 1/2W
2.7k 1/10W
4.7 1/2W
2.2k 1/8W
1.5k 1/10W
1k
1/8W
1k
1/10W
470 1/8W
220 1/8W
2.7k 1/10W
68
1/2W
100 1/10W
100 1/10W
100 1/10W
100 1/10W
8.2k 1/10W
12k 1/8W
10k 1/10W
220 1/10W
220k 1/8W
100 1/10W
Code
Ref. No.
Part No.
Description
Metal Film
Metal Film
Carbon
Metal Film
Metal Film
Carbon
Metal Film
Carbon
Carbon
Carbon
Metal Film
Metal Film
Carbon
Carbon
Carbon
Carbon
Carbon
Metal Film
Metal Oxide
Metal Film
Carbon
Metal Oxide
Carbon
Carbon
Metal Film
Metal Film
Carbon
Carbon
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Carbon
Metal Film
Cement
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AC
AA
AA
AD
AA
AB
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AE
Cement
AE
Metal Oxide
Carbon
Carbon
Metal Oxide
Carbon
Carbon
Metal Film
Metal Film
Fuse Resistor
Carbon
Carbon
Solid
Carbon
Carbon
Carbon
Solid
Metal Film
Carbon
Carbon
Metal Film
Carbon
Metal Film
Carbon
Carbon
Metal Film
Carbon
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Carbon
Metal Film
Metal Film
Carbon
Metal Film
AE
AA
AA
AE
AA
AA
AA
AA
AC
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
R813
R1067
R1001
R1002
R1003
R1004
R1005
R1011
R1012
R1013
R1014
R1015
R1016
R1017
R1019
R1020
R1021
R1022
R1023
R1024
R1025
R1026
R1027
R1028
R1030
R1031
R1032
R1033
R1034
R1035
R1036
R1037
R1038
R1039
R1040
R1041
R1043
R1044
R1045
R1046
R1065
VRN-MD2AL221J
VRN-MD2AL000J
VRD-RA2BE221J
VRN-MD2AL331J
VRN-MD2AL471J
VRN-MD2AL821J
VRD-RA2BE181J
VRN-MD2AL820J
VRN-MD2AL391J
VRN-MD2AL101J
VRD-RA2BE101J
VRN-MD2AL332J
VRD-RA2BE101J
VRN-MD2AL332J
VRN-MD2AL472J
VRD-RA2BE101J
VRN-MD2AL153J
VRD-RA2BE101J
VRN-MD2AL101J
VRN-MD2AL122J
VRN-MD2AL101J
VRN-MD2AL224J
VRD-RA2BE101J
VRD-RA2BE101J
VRN-MD2AL102J
VRD-RA2BE562J
VRN-MD2AL332J
VRD-RA2BE102J
VRD-RA2BE101J
VRN-MD2AL332J
VRN-MD2AL332J
VRD-RA2BE101J
VRD-RA2BE101J
VRN-MD2AL223J
VRN-MD2AL101J
VRN-MD2AL101J
VRN-MD2AL153J
VRN-MD2AL153J
VRD-RA2BE271J
VRD-RA2BE101J
VRN-MD2AL101J
å S701
S1001
S1002
S1003
S1004
S1005
QSW-P0591CEZZ
QSW-K0077GEZZ
QSW-K0077GEZZ
QSW-K0077GEZZ
QSW-K0077GEZZ
QSW-K0077GEZZ
å F701
FB306
FB501
FB502
FB602
FB701
FB702
FB751
FB752
å FH701
å FH702
J402
J403
J405
P301
P302
P502
P602
P602
P701
P712
P1001
P1001
QFS-C3229CEZZ
RBLN-0037CEZZ
RBLN-0037CEZZ
RBLN-0037CEZZ
RBLN-0037CEZZ
RBLN-0037CEZZ
RBLN-0037CEZZ
RBLN-0037CEZZ
RBLN-0037CEZZ
QFSHD1014CEZZ
QFSHD1013CEZZ
QJAKE0205CE04
QJAKE0205CE09
QJAKH0102PEZZ
QPLGN0441CEZZ
QPLGN0261CEZZ
QPLGN0660CEZZ
QPLGN0661CEZZ
QPLGN0641CEZZ
QPLGN0260CEZZ
QPLGN0269GEZZ
QPLGN0561CEZZ
QPLGN0541CEZZ
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
220
0
220
330
470
820
180
82
390
100
100
3.3k
100
3.3k
4.7k
100
15k
100
100
1.2k
100
220k
100
100
1k
5.6k
3.3k
1k
100
3.3k
3.3k
100
100
22k
100
100
15k
15k
270
100
100
1/10W
1/10W
1/8W
1/10W
1/10W
1/10W
1/8W
1/10W
1/10W
1/10W
1/8W
1/10W
1/8W
1/10W
1/10W
1/8W
1/10W
1/8W
1/10W
1/10W
1/10W
1/10W
1/8W
1/8W
1/10W
1/8W
1/10W
1/8W
1/8W
1/10W
1/10W
1/8W
1/8W
1/10W
1/10W
1/10W
1/10W
1/10W
1/8W
1/8W
1/10W
Metal Film
Metal Film
Carbon
Metal Film
Metal Film
Metal Film
Carbon
Metal Film
Metal Film
Metal Film
Carbon
Metal Film
Carbon
Metal Film
Metal Film
Carbon
Metal Film
Carbon
Metal Film
Metal Film
Metal Film
Metal Film
Carbon
Carbon
Metal Film
Carbon
Metal Film
Carbon
Carbon
Metal Film
Metal Film
Carbon
Carbon
Metal Film
Metal Film
Metal Film
Metal Film
Metal Film
Carbon
Carbon
Metal Film
Code
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AB
AA
AB
AA
AA
AB
AA
AB
AA
AA
AA
AA
AB
AB
AA
AA
AA
AA
AB
AA
AA
AB
AB
AA
AA
AA
AA
AA
AA
AB
AA
SWITCH
R
R
R
R
R
R
Switch
Switch, CH UP
Switch, CH DOWN
Switch, VOL. UP
Switch, VOL. DOWN
Switch, PICTURE/PRESET
AQ
AB
AB
AB
AB
AB
MISCELLANEOUS PARTS
45
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
Fuse,T3.5A/250V
Ferrite Bead
Ferrite Bead
Ferrite Bead
Ferrite Bead
Ferrite Bead
Ferrite Bead
Ferrite Bead
Ferrite Bead
Fuse Holder
Fuse Holder
Jack
Jack
Jack
Plug, 4pin (14A2-RU)
Plug, 2pin (14A1-RU)
Plug, 6pin(F)
Plug, 6pin(H) (14A1-RU)
Plug, 6pin(H) (14A2-RU)
Plug, 2pin
Plug, 2pin
Plug, 5pin(K) (14A1-RU)
Plug, 5pin(K) (14A2-RU)
AD
AB
AB
AB
AB
AB
AB
AB
AB
AC
AC
AD
AD
AE
AB
AB
AC
AD
AB
AC
AB
AB
AB
14A1-RU
14A2-RU
Ref. No.
Part No.
Description
P1002 QPLGN0561CEZZ
P1002 QPLGN0541CEZZ
RMC1001 RRMCU0235CEZZ
TP201 QLUGP0102PEZZ
RDA300 PRDAR0142PEFW
RDA300 PRDAR0248PEFW
RDA501 PRDAR0283PEFW
RDA701 PRDAR0260PEFW
RDA754 PRDAR0224PEFW
PWB-B
R
R
R
R
R
R
R
R
R
Code
Ref. No.
Plug, 5pin(BC) (14A1-RU)
AB
Plug, 5pin(BC) (14A2-RU)
AB
Remote Receiver
AK
Lug
AA
Heat Sink for IC301(14A1-RU)AD
Heat Sink for IC301(14A2-RU)AF
Heat Sink for IC501
AF
Heat Sink for IC701
AH
Heat Sink for Q602
AF
Part No.
Description
Code
MISCELLANEOUS PARTS
SP301 VSP9050PB25WA R
SP301 VSP9050PB25WA R
QACCZ2008PEZZ R
QANTR0018PEZZ R
QCNW-2377PEZZ R
QCNW-2378PEZZ R
Speaker
Speaker (14A2-RU)
AC Cord
Rod Antenna
Connecting Cord
Connecting Cord
(14A1-RU)
QCNW-2380PEZZ R Connecting Cord
(14A2-RU)
QCNW-2423PEN1 R Connecting Cord
DUNTK9990WEV4
CRT SOCKET UNIT
AM
AM
AM
AQ
AE
AE
AG
AF
TRANSISTORS
Q870
Q871
Q872
Q883
Q885
Q887
VSBF422////-1
VSBF422////-1
VSBF422////-1
VSBF421////-1
VSBF421////-1
VSBF421////-1
R
R
R
R
R
R
D811
D812
D880
D881
D882
D883
D884
D885
D886
D887
D888
RH-DX0475CEZZ
RH-DX0475CEZZ
RH-DX0475CEZZ
RH-DX0475CEZZ
RH-DX0475CEZZ
VHD1SS82///1A
VHD1SS82///1A
VHD1SS82///1A
VHD1SS82///1A
VHD1SS82///1A
VHD1SS82///1A
C871
C872
C873
C875
C876
C878
C880
C881
C882
VCKYPA1HB471K
VCKYPA1HB471K
VCKYPA1HB471K
VCKYPA2HB102K
RC-KZ0150CEZZ
VCEAGA2EW106M
VCKYPA1HB471K
VCKYPA1HB471K
VCKYPA1HB471K
BF422
BF422
BF422
BF421
BF421
BF421
AC
AC
AC
AC
AC
AC
SUPPLIED ACCESSORIES
ACCESSORIES
QPLGJ0113CEZZ
RRMCG1342PESA
TCAUA0002PEZZ
TiNS-6822PEZZ
DIODES
R
R
R
R
R
R
R
R
R
R
R
Diode
Diode
Diode
Diode
Diode
1SS82
1SS82
1SS82
1SS82
1SS82
1SS82
AB
AB
AB
AB
AB
AC
AC
AC
AC
AC
AC
TiNS-6827PEZZ
470p
470p
470p
1000p
1000p
10
470p
470p
470p
50V
50V
50V
500V
3kV
250V
50V
50V
50V
Ceramic
Ceramic
Ceramic
Ceramic
Ceramic
Electrolytic
Ceramic
Ceramic
Ceramic
VRD-RA2BE471J
VRD-RA2BE471J
VRD-RA2BE471J
VRS-VU3DE153J
VRD-RM2HD272J
VRS-VU3DE153J
VRD-RM2HD272J
VRS-VU3DE153J
VRD-RM2HD272J
VRD-RA2BE471J
VRD-RA2BE102J
VRD-RA2BE102J
VRD-RA2BE102J
VRD-RA2BE471J
VRD-RA2BE471J
R
R
R
R
R
R
R
R
R
R
R
R
R
R
R
470
470
470
15k
2.7k
15k
2.7k
15k
2.7k
470
1k
1k
1k
470
470
1/8W
1/8W
1/8W
2W
1/2W
2W
1/2W
2W
1/2W
1/8W
1/8W
1/8W
1/8W
1/8W
1/8W
SPAKC6579PEZZ
SPAKC6587PEZZ
SPAKP0056PEZZ
SPAKX2713PEZZ
SPAKX2724PEZZ
SSAKA0031PEZZ
AA
AA
AA
AA
AB
AC
AA
AA
AA
AA
AA
AA
AB
AA
AB
AA
AB
AA
AA
AA
AA
AA
AA
AA
1
1-1
1-1
1-2
1-2
1-3
1-3
1-4
1-4
1-5
1-5
1-6
1-6
2
MISCELLANEOUS PARTS
P851
QPLGN0661CEZZ R Plug, 6pin(K)
P882
QPLGN0561CEZZ R Plug, 5pin(K)
å SC881 QSOCV0839CEZZ R CRT Socket
AF
-
Packing Case (14A1RU)
Packing Case (14A2-RU)
Wrapping Paper
Buffer Material (14A1RU)
Buffer Material (14A2-RU)
Polyethylene Bag
—
—
—
—
—
—
CABINET PARTS
1
Carbon
Carbon
Carbon
Metal Oxide
Carbon
Metal Oxide
Carbon
Metal Oxide
Carbon
Carbon
Carbon
Carbon
Carbon
Carbon
Carbon
AG
AU
AB
AF
< NOT REPLACEMENT ITEM >
RESISTORS
R879
R880
R881
R882
R883
R884
R885
R886
R887
R888
R892
R893
R894
R898
R899
AC Plug Adaptor
Infrared Remote Control Unit
Caution Card
Operation Manual
(14A1RU)
R Operation Manual
(14A2-RU)
PACKING PARTS
CAPACITORS
R
R
R
R
R
R
R
R
R
R
R
R
R
AD
AB
AK
2-1
2-1
46
CCABA2506WEV0 R Front Cabinet Ass’y
(14A1-RU)
CCABA2528WEV0 R Front Cabinet Ass’y
(14A2-RU)
Not Available
- Front Cabinet (14A1-RU)
Not Available
- Front Cabinet (14A2-RU)
HBDGB0018PESB R SHARP Badge (14A1-RU)
HBDGB0019PESB R SHARP Badge (14A2-RU)
JBTN-0314PESA R Control Button (14A1-RU)
JBTN-0319PESA R Control Button (14A2-RU)
GCOVA0105PESA R LED/RC Cover (14A1-RU)
GCOVA0120PESA R LED/RC Cover (14A2-RU)
JBTN-0313PESA R Power Button (14A1-RU)
JBTN-0318PESA R Power Button (14A2-RU)
MSPRC0068CEFW R Power Button Spring
(14A1-RU)
MSPRC0008PEFW R Power Button Spring
(14A2-RU)
GCABB2387PEKA R Rear Cabinet Ass’y
(14A1-RU)
CCABB2395WEV1 R Rear Cabinet Ass’y
(14A2-RU)
Not Available
- Rear Cabinet (14A2-RU)
BC
BD
—
—
AD
AD
AD
AE
AC
AC
AC
AD
AA
AB
AU
AW
—
14A1-RU
14A2-RU
Ref. No.
Part No.
Description
Code
Ref. No.
2
1 1-1
1-2
1-5
1-4
1-3
1-6
(14A1-RU)
1
2
1-1
1-2
1-5
1-4
1-3
1-6
(14A2-RU)
47
Part No.
Description
Code
14A1-RU
14A2-RU
Ref. No.
Part No.
Description
Code
Ref. No.
Part No.
Description
Code
COPYRIGHT © 2000 BY SHARP CORPORATION
ALL RIGHTS RESERVED.
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted in
any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without
prior written permission of the publisher.
SHARP CORPORATION
AV Systems Group
Quality & Reliability Control Center
Yaita, Tochigi 329-2193, Japan
DSEMPSREC. TQ1027-S
Nov. 2000 Printed in Japan
NA. KY
48

Similar documents

service manual service-anleitung

service manual service-anleitung thoroughly familiar with all safety checks and servicing guidelines as follows: » Use an AC voltmeter with sensitivity of 5000 ohm per volt., or higher, sensitivity to measure the AC voltage drop a...

More information

25R-M100 - ePanorama.net

25R-M100 - ePanorama.net » IMPORTANT SERVICE SAFETY PRECAUTION ................................................................................. 2 » LOCATION OF USER'S CONTROL .................................................

More information

service manual - Philips Parts and Accessories

service manual - Philips Parts and Accessories CONTENTS Page » ELECTRICAL SPECIFICATIONS........................................................................................................ 1 » IMPORTANT SERVICE SAFETY PRECAUTION ..............

More information