WF -109 CAT 4000 SERIES

ENGINEERING DATA
TM
High Torque,
Low Speed Motors
4000 Series
Interchangeable with:
• Charlynn
• White
• Ross
• Parker
• Danfoss
w w w. w f d y n e . c o m
TM
INDEX
1-800-842-5377
Cross Reference Guide ..........................................2
Introduction..............................................................3
6000-Series ..........................................................24
Shaft Data ................................................25
Model Code..............................................25
Installation Data ......................................26
Shaft Seal ................................................26
Case Drain ..............................................26
Shaft Rotation ..........................................26
Radial Forces ..........................................26
Technical Data ........................................27-29
MOTOR CROSS-REFERENCE GUIDE
Western FluiDyne
Eaton/Charlynn
White
Danfoss
Parker Ross/ TRW
H Series
A, H (130-,101-)
RS (200-)
DH, OMP
TC, TB, MK, MG
S Series
S, T (103-, 158- )
WR (255-)
OMR, DS (151-)
TB, TE, MG, MF
2000 Series
2000 (104-)
HB, RE (300-, 500-)
OMS, OME
TF, TG, MB, ME
6000 Series
4K, 6K (109-,112-)
RE, DR (500-, 600-)
OMT, TMK, TMT
TG, TH, TK, ME, MJ
10,000 Series
10K (119-)
DT
OMV, TMV
Western FluiDyne reserves the right to make alterations to it's product.
2
TM
HIGH TORQUE, LOW SPEED MOTORS
1-800-842-5377
Western FluiDyne LSHT Hydraulic Motors
Western FluiDyne’s extensive range of multiple displacement Low Speed – High Torque (LSHT) hydraulic motors are form
fit and function interchangeable with many of the common motor products from Parker, White, Charlynn and Danfoss.
Both Geroter and Geroler technologies are incorporated in the Western FluiDyne “H” Series, “S” series, “2000” series,
“6000” series and “10,000” series.
These Western FluiDyne motors are manufactured with ISO 9001:2000 documented quality standards which results in
product which consistently meets or exceeds the life and performance expectations of similar products.
The Western FluiDyne product is built to perform in even the harsh environments where rugged mobile equipment is expected to operate. For optimal life the following guidelines are recommended:
1) Motors should be operated at less than 30% of full rated performance for the first hour of operation
2) During normal sustained operations, oil temperature should be between 70 to 150 degrees F (20 to 60 degrees C)
3) Maximum operating temperature should not exceed 190 degrees F (90 degrees C)
4) ISO oil cleanliness level should be 18/13 or cleaner. Normally this is achieved with Beta 10=100 full flow return
line filtration.
5) High grade petroleum based hydraulic oil must be used
6) Minimum oil viscosity should be 100 SUS
7) Simultaneous maximum torque and maximum speed is not recommend for this design of motor
Technical Data Summary:
Model
Distributor
type
Displacement
in3/rev
cm3/rev
Maximum
Operating Pressure
PSI
BAR
Speed
RPM
H Series
Axial
3-23
50-400
2400
163
30-800
S Series
Axial
3-23
50-375
3000
200
30-970
2000 Series
Disc
5-23
80-375
3250
225
30-800
6000 Series
Disc
10-49
160-800
3400
240
30-705
10,000 Series
Disc
19-49
315- 800
4000
280
10-446
wfdyne.com
3
WF 4000 SERIES
WF4000 series are large volume, disc valve, high pressure motors.
Characteristic features:
* The advanced design in disc distribution flow provides improved performance at low speed.
The disc compensates for wear providing volumetric efficiencies.
* The double tapered roller bearings allow for high axial and radial loads providing for wide
application use with higher pressures and higher torques.
Main Specifications
Fluidyne disp. type
160
200
250
315
400
500
630
Geometric displacement cm3/rev
(cu.in./rev)
161.1
(9.8)
201.4
(12.3)
251.8
(15.4)
326.3
(19.9)
410.9
(25.0)
523.6
(32.0)
629.1
(38.0)
625
780
4,160
4,956
5,921
21.1
26.4
33
3050
3630
4351
43
625
750
5,222
6,284
7,417
26.4
33
39.6
3050
3630
4351
44
500
600
6,461
7,789
9,169
26.4
33
39.6
3050
3630
4351
45
380
305
240
196
460
365
285
233
8,408 9,559 10,798 11,665
10,090 11,152 12,126 13,258
11,916 12,836 14,549 14,328
26.4
26.4
26.4
26.4
33
33
33
33
39.6
39.6
39.6
39.6
3050
3050
3050
3050
3630
3630
3630
3630
4351
4351
4351
4351
46.3
48.5
50.7
53
cont.
int.
cont.
Max Torque (in/lbs)
int.
peak
rated
Max flow (GPM)
cont.
int.
cont.
Max inlet Pressure (PSI) int.
peak
Weight (lbs)
Max speed (RPM)
* Continuous pressure: Max. value of operating motor continuously
* Internittent pressure: Max. value of operating motor for 6 seconds per minute
* Peak pressure: Max. value of operating motor in 0.6 second per minute.
FluiDyne 109- 4000 SERIES
WF Geroler Dimension mm (inch) :
17 (0.67)
21 (0.83)
14 (0.56)
20 (0.79)
27 (1.07)
35 (1.38)
47 (1.85)
DISPLACEMENT cm3/r (in3/r)
MOUNTING
Shafts
1 1/4" STRAIGHT
4 BOLT STD
SAE B FLANGE
(4.0" PILOT)
1 5/8" TAPERED
1 1/4" 14 TOOTH
SPLINE
1 1/4" STRAIGHT
4 BOLT STD
SAE C MOUNT
(5.0" PILOT)
1 1/4" 14 TOOTH
SPLINE
40 mm STRAIGHT
1 1/2" 17 TOOTH
SPLINE
1 1/4" STRAIGHT
FluiDyne
160 cm3
(9.8)
200 cm3
(12.3)
250 cm3
(15.4)
315 cm3
(19.9)
400 cm3
(25)
500 cm3
(32)
630 cm3
(38)
Char-Lynn reference
160 cm3
(9.9)
205 cm3
(12.5)
245 cm3
(15)
310 cm3
(19)
395 cm3
(24)
495 cm3
(30)
625 cm3
(38)
PORTS
1 1/16" -12 O-RING
STAGGERED
3/4" SPLIT FLANGE
WF1091102
WF1091103
WF1091104
WF1091105
WF1091106
WF1091212
WF1091215
WF1091002
WF1091003
WF1091055
WF1091056
WF1091057
-
-
1 1/16" -12 O-RING
STAGGERED
WF1091109
WF1091110
WF10911111
WF091112
WF1091113
WF1091479
WF1091455
3/4" SPLIT FLANGE
WF1091007
WF1091008
WF1091059
WF1091402
WF1091061
-
-
1 1/16" -12 O-RING
STAGGERED
WF1091116
WF1091117
WF1091118
WF1091119
WF1091120
WF1091363
WF1091219
3/4" SPLIT FLANGE
WF1091012
WF1091013
WF1091063
WF1091064
WF1091065
-
-
-
WF1091296
WF1091427
WF1091311
WF1091366
WF1091206
WF1091207
WF1091287
WF1091203
WF1091304
WF1091220
WF1091280
WF1091316
WF1091337
3/4" SPLIT FLANGE
WF1091370
WF1091333
WF1091263
WF1091450
WF1091278
WF1091181
-
-
G 3/4 (BSP) O-RING
WF1091227
WF1091224
WF1091225
WF1091189
WF1091190
WF1091267
WF1091355
1 1/16" -12 O-RING
STAGGERED
WF1091275
-
WF1091330
WF1091283
W1091453
WF1091290
WF1091400
1 1/16" -12 O-RING
STAGGERED
1 1/16" -12 O-RING
STAGGERED
G 3/4 (BSP) O-RING
WF1091193
WF1091194
WF1091195
WF1091196
WF1091197
WF1091383
-
1 1/16" -12 O-RING
STAGGERED
WF1101076
WF1101077
WF1101078
WF1101079
WF1101080
-
WF1101122
3/4" SPLIT FLANGE
WF1101002
WF1101003
WF1101041
WF1101042
WF1101043
-
-
1 1/16" -12 O-RING
STAGGERED
WF1101083
WF1101084
WF1101085
WF1101086
WF1101087
WF1101116
WF1101117
3/4" SPLIT FLANGE
WF1101007
WF1101008
WF1101045
WF1101046
WF1101047
-
-
G 3/4 (BSP) O-RING
WF1101110
WF1101111
WF1101112
WF1101113
WF1101125
-
-
1 1/16" -12 O-RING
STAGGERED
WF1101100
WF1101101
WF1101102
WF1101103
WF1101104
-
-
3/4" SPLIT FLANGE
WF1101012
WF1101013
WF1101049
WF1101050
WF1101051
-
-
1 1/16" O-RING
WF1111035
WF1111036
WF1111037
WF1111038
WF1111039
WF1111062
WF1111063
3/4" SPLIT FLANGE
WF1111045
WF1111046
WF1111016
WF1111017
WF1111018
-
-
G 3/4 (BSP) O-RING
WF1111054
WF1111055
WF1111056
WF1111057
WF1111058
-
-
Max Torque (Ft*lbs)
Continuous
4,166
5,209
6,430
8,500
9,680
11,000
11,656
Max ∆Pressure (PSI)
Max Flow (GPM)
Continuous
Continuous
2,900
2,900
2,900
2,610
2,320
2,030
1,813
26
33
33
33
33
33
33
Max RPM
Continuous
Weight (LBS)
Weight
614
20
615
20
495
45
380
46
302
48
237
52
196
53
1 5/8" TAPERED
WHEEL MOTOR
40 mm STRAIGHT
1 1/4" 14 TOOTH
SPLINE
BEARINGLESS
WF-Charlynn 109- 4K-Series V11.21.2012.xls
HIGH TORQUE, LOW SPEED MOTORS
1-1/4” Straight Keyed
42,0 [1.65]
31,75
[1.250]
7,94 [0.3125]
03
53,1 [2.09]
Max. Coupling
◄ End of Shaft to
Mounting Surface (Std)
Ø 38,1
[1.50]
3/8-16 UNC
18,7 [.74] Deep
1-1/4” 14 -Tooth Spline
70,9 [2.79]
38,1
[1.50]
8,0
[.315]
◄
51,8
[2.04] Max. Coupling
8 X 12 X 63 Key
93,9 [3.70]
12,0 [0.47]
5 [0.19]
63[2.48]
43
[1.69]
53,1 [2.09]
3/8-16 UNC
18,7 [.74] Deep
◄
40mm Straight Keyed
14
ANSI B92.1 1976 Spline
FRSF Fit 14 Tooth 12/24
65,0 [2.56]
31,2 [1.23]
Min. Full
Spline
31,75
[1.25]
76,6 [3.00]
Thru
ANSI B92.1 1976 Spline
FRSF 17 Tooth 12/24 DP
◄(Wheel)
1:8
Ø 4,1 [.16]
Ø 31,7
[1.25]
3/8-16 UNC
18,7[.74] Deep
◄
11,12 [0.44] Ø 41,28
[1.625]
5,54 [.22]
3/8” Sq. Key
71[2.79]
35,33
[1.39]
164,8 [6.49]
1-1/4-18 UNEF-2A
1-1/2” 17 -Tooth Spline
13
7/16” Sq. Key
Ø 33
[1.3]
01
1-5/8” Tapered
02
◄
Ø 40
[1.575]
4000 SERIES SHAFT DATA
1-800-842-5377
81,3 [3.20]
Max. Coupling
M12 x 1,75 -6H
24,9 [.98] Deep
Max. Coupling
4000 SERIES MODEL CODE
M04
- 315
-
F
-
01
4000 Series
( 109- )
-
B
-
00
-
Ports ²
Mounting Type
Displacement
cm³/r (in³/r)
(Packaging as Req’d)
0 - No Paint, Individual Box
A - Painted Black
C - Corrosion Protected
N - Nickel Plated Body
2 All units have plugged 7/16-20
* Available on selected models
or G1/4 drain, for use as needed.
L1
L2
119,9
[4.72]
Max,
Square
101,6
[Ø 4.0]
Case Drain Port
10,7/9,1
[.42/.36]
15,2/14,5
[.60/.57] (4)
B - 4 Bolt SAE-B Mount
Standard Mount Motor Dimensions
L1
Displacement
mm [inch]
cm3/r [in3/r]
* L2
mm [inch]
*L
mm [inch]
160 [ 9.8]
200 [12.3]
250 [15.4]
315 [19.9]
400 [25.0]
500 [32.0]
630 [38.0]
142,5 [5.61]
146,5 [5.77]
166,5 [6.56]
172,5 [6.80]
179,5 [7.07]
187,5 [7.39]
199,5 [7.86]
193,0 [7.60]
197,0 [7.76]
240,5 [9.47]
246,5 [9.71]
253,5 [9.98]
261,5 [10.11]
273,5 [10.77]
17 [0.67]
21 [0.83]
14 [0.56]
20 [0.79]
27 [1.07]
35 [1.38]
47 [1.85]
127,0 [5.00]
Dia. Bolt Circle
*Standard Rotation
Viewed from Shaft End
103 [4.06]
22,4/21,8
[.88/.86]
Port A
13.2
[0.52]
L Max.
Port A
89,80
[3.536]
Square
77 [3.03]
29.2
[1.15]
75.5
[2.97]
Port B
0F - Six
00 - None
01 - Viton Shaft Seal
07 - Viton Seals
13 - Seal Guard *
16 - Reverse Rotation
27 - Loctite Retainer Bolts
29 - Rotate Flange 90º
4000 SERIES INSTALLATION DATA
Flange
SAE- B
Design Code
(Hardware)
00 - None (Bearingless)
01 - 1 1/4 inch Dia. Straight Key
02 - 1 5/8 inch Dia. Tapered Key & Nut
03 - 1 1/4 inch Dia. Splined 14T
13 - 1 1/2 inch Dia. Splined 17T
14 - 40 mm Dia. Straight Key
Additional flange mounts and drive shafts available, consult factory
0F
Special Features
Output Shaft
160 (9.8)
200 (12.3)
250 (15.4)
315 (19.9)
400 (25.0)
500 (32.0)
630 (38.0)
-
Paint
A - 7/8 - 14 O-ring
B - 1 1/16 O-ring
C - G 3/4 (BSP) O-ring
D - 3/4 inch 4 Bolt Split Flange
H - M22 x 1, 5-6H (ISO) O-ring
A - 4 Bolt (Bearingless)
B - 4 Bolt (SAE B)
C - 4 Bolt (Wheel)
F - 4 Bolt (SAE C)
A
Port A Pressurized – CW
Shaft Rotation
Port B Pressurized – CCW
Shaft Rotation
Port B
Drain Port T
7/16-20 or G1/4
8
[0.31]
14,53
[.57] Dia.
Thru Max.
12,7 [0.50]
4,3 [.17] to
* Add
L and L2 Dim.
For SAE-C Mount
(see Chart)
Flange
SAE- C
148,3
127,0
[5.84]
[Ø 5.0] Max.
Pilot Dia. Square
161,92
[6.375]
Dia. B.C.
26.2 [1.03]
F - 4 Bolt SAE-C Mount
FluiDyneFP.com
76,2/63,5
[3.00/2.50]
WF-109 Cat 4K Model Code_pgV10.13V2
4000 SERIES BEARINGLESS MOTOR
DIMENSION AND MOUNTING DATA
L
62 max 71 max
[2.44] [2.80]
L 2
L 1
Port A
Port B
Drain Port T
A
L2
[6.22] [1.06] [4.23]
158
27
107.5
0
315
163
20
115
400
6.69]
[1.06] [4.80]
170
27
122
500
[7.01] [1.38] [5.12]
178
35
130
ø6 [0.24]
630
[7.48] [1.85] [5.59]
190
47
142
ø162 [6.38]
stator and rotor for displacethe dimension of L1 + 3mm
stator and rotor for displacethe dimension of L1 + 7mm.
28 [1.10]
[6.42] [0.79] [4.53]
Note: 1)The thickness of the
ments from 160-250 is
2)The thickness of the
ments from 315-630 is
ø6
[0.24]
ø 127 -0,63
[5.00]
250
1]
100.5
.8
96.5
21
1]
17
152
.8
148
[5.98] [0.83] [3.96]
[5
[5.83] [0.67] [3.80]
200
10 [0.39]
6
160
[5
L1
6
L
7,
L2
14
L1
7,
L
16 [0.63]
ø22 [0.87]
14
MODEL
BEARINGLESS
MILLIMETERS
28 [1.10]
[INCHES]
4-ø14
4-[0.55]
50
42
[1.97] [1.65]
31
[1.22]
max L
L 2
L 1
71 [2.80] 62 [2.44]
124 [4.88]
MOUNTING DATA
Port A
Port B
[INCHES]
MODEL
MILLIMETERS
L2
160W
[0.67]
[3.03]
17
77
160
200W
[0.83]
[3.19]
21
81
250W
[1.07]
[3.42]
27
87
315W
[0.79]
[3.58]
20
400W
[1.07]
[3.86]
27
500W
[1.38]
[4.17]
630W
[1.85]
[4.64]
Note:
L1
[INCHES]
L1
L2
MODEL
L
MILLIMETERS
L1
L2
L
[7.60]
[0.67]
[5.61]
193
200
[7.76]
[0.83]
[5.77]
197
21
146.5
250
[8.00]
[0.56]
[6.01]
203
27
152.5
91
315
[8.19]
[0.79]
[6.17]
208
20
156.5
98
400
[8.47]
[1.07]
[6.44]
215
27
163.5
35
106
500
[8.78]
[1.38]
[6.76]
223
35
171.5
47
118
630
[9.26]
[1.85]
[7.23]
235
47
183.5
1) The thickness of the stator and rotor for displacements from 160-250 is the dimension of L1 + 3mm
2) The thickness of the stator and rotor for displacements from 315-800 is the dimension of L1 + 7mm.
L1
17
L2
142.5
WF 4000 Series Hydraulic Motor
Permissible shaft seal pressure
In applications without drain line, output shaft seal exceeds a bit of the
pressure in the return line. When applications use the drain line, the pressure
of output shaft seal equals the pressure in drain line.
Standard direction of shaft rotation: Standard
Axial and Radial forces
When facing shaft end of motor,shaft to rotate:
Clockwise when port "A" is pressurized.
Counter-clockwise port "B" is pressurized.
The output shaft runs in tapered bearings that permit high
axial and radial forces, Curve "A" shows max radial shaft load,
Any shaft loads exceeding the values quoted in the curve will
involve a risk of breakage, The two other curves apply to a B10
bearing life of 3000 hours at 200 RPM.
WF4000
Performance Data
10.5
15.9
21.1
Max. cont.
26.4
Max. Int.
33.0
2,018
58
2,071
117
2,080
243
2,080
362
2,027
485
1,929
606
1,868
758
1,740
2,320
2,900
3,480
2,434
56
2,452
114
2,452
236
2,452
356
2,443
478
2,381
598
2,310
750
3,195
54
3,292
109
3,372
230
3,372
349
3,354
470
3,275
590
3,177
741
3,956
50
4,062
103
4,169
223
4,160
340
4,124
462
4,027
582
3,965
731
4,735
44
4,930
95
5,071
212
5,063
330
5,018
447
4,939
570
4,886
715
Torque (in-lbs) 2,310
Speed (RPM)
750
250 (251.8 cm3/rev)
Pressure PSI
580
1,160 1,450
Flow (GPM)
2.64
5.28
10.5
15.9
21.1
26.4
Max. cont.
33.0
Max. Int.
39.6
1,221
38
1,266
76
1,230
156
1,168
237
1,133
317
1,115
396
1,027
495
779
592
2,531
38
2,620
75
2,664
154
2,602
236
2,505
316
2,496
394
2,301
492
2,142
589
3,142
37
3,221
74
3,292
152
3,292
233
3,221
314
3,142
391
3,009
488
2,832
585
400 (410.9 cm3/rev)
Pressure PSI
435
870
1,305
Flow (GPM)
2.64
5.28
10.5
15.9
21.1
26.4
Max. cont.
33.0
Max. Int.
39.6
Flow (GPM)
2.64
5.28
10.5
15.9
21.1
26.4
Max. cont.
33.0
Max. Int.
39.6
Max. cont.
1,740
2,320
2,900
3,480
3,708
36
3,823
72
3,894
149
3,903
229
3,832
308
3,779
387
3,664
483
3,513
580
4,947
34
5,133
70
5,248
146
5,239
224
5,195
303
5,151
381
5,027
476
4,885
572
6,098
32
6,266
67
6,399
142
6,434
219
6,381
299
6,337
373
6,222
469
6,071
565
7,292
31
7,549
62
7,823
134
7,859
207
7,850
284
7,779
359
7,646
454
7,496
545
Max. cont.
2,611
3,046
4,956
22
5,000
47
5,018
93
4,983
139
4,894
188
4,761
238
4,637
298
4,496
358
6,328
21
6,425
44
6,487
90
6,452
135
6,363
184
6,266
234
6,089
294
5,894
354
7,832
20
7,956
42
8,133
87
8,142
131
8,071
180
7,930
228
7,726
289
7,540
350
9,293
19
9,478
40
9,655
83
9,691
127
9,593
176
9,443
224
9,248
285
9,027
346
10,700
18
10,939
38
11,178
79
11,231
121
11,178
170
11,080
218
10,806
278
10,593
339
630 (629.1 cm3/rev)
Pressure PSI
435
870
1,305
1,523
1,740
2,031
2,321
7,983
13
8,434
26
8,735
60
8,655
91
8,540
119
8,363
152
8,239
192
8,151
230
9,505
13
9,885
26
10,363
59
10,372
90
10,372
118
10,231
150
10,062
191
9,921
227
10,567
11
10,965
24
11,576
56
11,664
86
1,162
114
11,532
147
11,434
187
11,301
223
12,063
11
12,452
22
13,125
54
13,257
82
13,248
110
13,169
142
13,027
183
12,868
217
2,062
14
2,097
28
2,115
62
1,974
94
1,947
123
1,841
156
1,779
196
1,540
233
4,602
14
4,903
27
4,894
62
4,814
94
4,752
122
4,620
155
4,416
196
4,354
232
7,036
13
7,407
27
7,611
61
7,638
92
7,558
121
7,636
153
7,169
194
6,947
231
10.5
15.9
21.1
26.4
Max. cont.
33.0
Max. Int.
39.6
2.64
5.28
10.5
15.9
21.1
26.4
Max. cont.
33.0
Max. Int.
39.6
Max. Int.
2,176
3,248
23
3,275
48
3,275
95
3,195
143
3,124
191
3,000
240
2,735
300
2,584
362
5.28
Max. Int.
1,740
1,558
24
1,584
49
1,558
96
1,540
145
1,469
193
1,328
242
1,195
302
1,115
364
2.64
Flow (GPM)
5.28
1,558
59
1,602
120
1,593
246
1,575
367
1,531
489
1,416
611
1,309
764
200 (201.4 cm3/rev)
Pressure PSI
580
1,160 1,450
Max. Int.
Flow (GPM)
Flow (GPM)
2.64
779
60
787
121
805
249
726
371
690
492
620
614
513
770
Max. cont.
Max. cont.
Max. Int.
2.64
Flow (GPM)
160 (161.1 cm3/rev)
Pressure PSI
580
1,160 1,450
Performance Data
5.28
10.5
15.9
21.1
26.4
Max. cont.
33.0
Max. Int.
39.6
Max. cont.
Max. Int.
1,740
2,320
2,900
3,480
2,558
45
2,637
92
2,620
191
2,611
292
2,558
389
2,531
486
2,443
607
2,301
735
3,009
42
3,071
90
3,115
187
3,115
287
3,098
384
3,044
482
2,947
602
2,867
727
4,018
39
4,142
87
4,204
183
4,230
282
4,195
377
4,168
475
4,062
595
3,956
717
4,956
37
5,098
84
5,213
178
5,213
276
5,186
370
5,133
467
5,009
588
4,903
706
5,921
33
6,160
75
6,337
167
6,354
263
6,337
359
6,301
460
6,168
572
6,036
682
315 (326.3 cm3/rev)
Pressure PSI
580
1,160 1,450
1,740
2,320
2,900
3,480
4,009
28
4,177
58
4,283
118
4,363
179
4,239
239
4,133
301
3,956
375
3,823
453
4,823
27
4,974
56
5,045
115
5,071
175
5,000
236
4,974
298
4,814
371
4,655
449
6,496
26
6,699
54
6,850
112
6,832
172
6,797
231
6,708
294
6,593
367
6,310
444
7,885
25
8,115
52
8,443
109
8,514
168
8,443
227
8,337
289
8,142
362
7,912
431
9,399
23
9,815
50
10,169
104
10,213
158
10,204
217
10,116
276
9,974
349
9,708
425
500 (523.6 cm3/rev)
Pressure PSI
435
870
1,305
1,740
2,031
2,321
2,611
7,894
17
8,124
34
8,328
72
8,328
109
8,204
147
7,974
185
7,761
233
7,549
280
9,293
16
9,470
33
9,682
70
9,629
107
9,523
145
9,408
183
9,062
231
8,885
278
10,558
15
10,797
32
11,009
68
11,018
105
11,009
143
10,832
181
10,611
229
10,328
276
11,859
13
12,186
30
12,585
64
12,470
101
12,399
138
12,240
177
11,965
225
11,726
272
1,097
47
1,106
95
1,062
195
1,027
297
956
395
876
493
743
615
620
743
1,628
30
1,673
60
1,690
121
1,673
183
1,584
244
1,496
305
1,301
380
1,053
458
1,965
18
2,044
37
2,036
75
1,991
113
1,885
151
1,717
189
1,611
237
1,301
284
2,062
46
2,115
95
2,133
193
2,097
295
2,044
393
2,009
490
1,841
611
1,717
740
3,213
29
3,363
59
3,372
120
3,328
181
3,266
242
3,159
304
2,974
378
2,814
456
3,991
18
4,106
36
4,124
74
4,044
112
3,814
150
3,717
188
3,522
236
3,266
283
6,124
18
6,319
35
6,434
73
6,319
111
6,160
149
6,018
187
5,673
235
5,469
282
Max. cont.
Max. Int.
Max. cont.
Max. Int.
TM
31915 Groesbeck Highway • Fraser, Michigan 48026
PH: 1-800-842-5377 • FAX: 1-888-842-5377 • Email: [email protected]
www.wfdyne.com