LEADERMAC Model LMC 518S Smartmac

John G. Weber Co.
1133 South 7th St.
Sheboygan, WI 53081
Toll Free: 800-793-4494
E-mail:[email protected]
Website: www.johngweber.com
We are pleased to offer the following for your consideration.
1 Only
Used very good condition
LEADERMAC Model LMC 518S Smartmac
8” 5 Head Moulder
SPECIFICATIONS
Thickness Material
.4”(5/16” optional) to 5”
Width Material
.59” to 8”
Min length of material
7.87” (Butt fed)
Feed Speeds to
20-80 FPM (6-24 MPM)
Vert. adjust. side heads
.787” (20mm)
Hor. adjust. top/btm heads .787” (20mm)
Net weight approx.
8,200 lbs.
MAIN FRAME, MACHINE BED & ENCLOSURE
1 Piece – Cast Iron Main Frame. Specially heat treated for maximum stability and
minimum vibration
78 inch (2 meter) long Adjustable Straightening Infeed Table and Fence (each
adjustable .4 inch)
Lift up sound and safety Enclosure including safety interlocks and good lighting inside the
enclosure
Lubrication to all main slides
DRIVE INCLUDES
Maintenance free Full Cardan Shaft Drive to feedworks for balanced drive performance,
with individual worm reduction gear box to each feed roller station
Powered rise and fall to extra heavy feed support beam by 1 hp/.75 kw motor.
Upper support Beam is supported on large center column for best, most rigid upper
beam support.
All feed rolls and pressures move with top beam rise and fall, including safety switches
at extreme points.
6 Top Driven Feed Rolls
Top & Bottom – Full Width driven infeed rolls before first bottom head
Top Roll with pneumatic rise and fall by switch
Pneumatic pressure(tension) to all top feed rolls with pressure regulator controls
Infeed driven serrated Steel feed rolls up to top head are hardened and chromed to resist
wear and prevent chips and shavings from sticking to them
Intermediate short stock top driven feed roll station with pneumatic pressure for feeding
minimum 8”(200mm) length work pieces. It is easily flipped up for rear side head removal.
Polyurethane top feed rolls after top head
Top/Bottom Powered Outfeed Rolls
Full width driven plain outfeed bed roll
Inch forward and reverse to feed with duplicate control at top head position for fast and
easy setting
Feed roll diameter 5.5” / 140mm
4 HP Variable Speed Drive to 20-85 FPM
SPINDLE ASSEMBLIES, CUTTERHEADS & POSITIONING
All Heads are Standard 6000RPM (6800 rpm optional)and belt driven
40 mm diameter spindles (1 ½”, 1 13/16” or 50 mm – Optional)
Spindles are manufactured from SCM-440 tool steel (Imported from Mitsubishi-Japan) with
special heat treating to HR 55C Harness fitted with 2 pairs of Duplex SKF Super precision
high speed Bearings to provide the best in cutting stability with permanent accuracy.
Spindle Tolerance is guaranteed to +/-0.002mm / 0.00007” accuracy. They are permanent
grease lubed and are sealed and are impervious to dust and water.
Edge reference straightening system
Adjustment of all spindles from front – Easy to operate stations
All spindles have horizontal and vertical adjustment, with mechanical digital readouts
for fast and accurate setting, except 1st bottom head which has vertical only.
Vertical Spindle – Vertical Adjustment – .787”
Horizontal Spindle – Horizontal Adjustment - .787”
Independent manual vertical adjustment to top head.
Single Std Digital Counters included all Heads (Siko Dual Optional)
Digital Readouts in Inch
HEAD HP
1) Bottom Head
7.5 HP
2 & 3) Right Side/Left Side Heads 15 HP
4) Top Head
15 HP
5) 2nd Bottom Head
10 HP
John G. Weber Co.
SWING
5” to 6.3”
4” to 7”
4” to 8”
4” to 8”
(125 – 160 mm)
(100 – 180 mm)
(100 – 200 mm)
(100 – 200 mm)
HOOD SIZE
4.92” (125 mm)
4.92” (125 mm)
4.92” (125 mm)
4.92” (125 mm)
Page 2 of 10
CHIPBREAKERS, FENCES & HOLDOWNS/HOLDOVERS, ETC.
Tables, Bedplates, Chipbreakers and Fences are Hard Chromed
1.25” (32mm) high fences
Sectional Chip breakers before top heads with vertical screw adjustment and mechanical
digital position readout
Double side pressure unit opposite fence side head moving with near side head
Left Side Head equipped with telescopic bed plate
Side guide after near side head moving with near side head
Pad pressure(Pressure Plates) after top head with vertical screw adjustment and
mechanical digital position readout
Outfeed bed plate is easily shimmed
MISCELLANEOUS features and inclusions
Hand pump bed lubrication system
Greasing of all critical points from central location
Safety interlock at infeed to prevent feeding oversized or double feeding material
Dust hoods
Toolkit
Instruction and maintenance manual, electrical diagram and parts list
ELECTRICAL
TECO-Westinghouse or Siemens – Electric Motors – excellent quality & heavy duty
Limit switch at infeed to prevent feeding oversized material and double ups
I.E.C. – Telemecanique-Square D Electrics meet or exceed UL/CSA Standards
Machine and electrical components meet CE Safety Standards
Machines are equipped with Wye-Delta Soft Starters, main disconnect, multiple
E Stops and 230/460/3/60 electrics. Wired to 230 volts
Age: 2 0 0 7
Condition: Very Good
Price as above/below
$ 24,395.00
Machine was installed in January 2008
Machine comes complete with 1 set of Carbide Spiral Cutterheads, extra heads
available at special pricing.
John G. Weber Co.
Page 3 of 10
Options Included with Basic Moulder
Increased Cutterhead Hp’s from Standard
Side Heads – from 10 HP to 15 HP (Value $ 720.) ................................................. $ Included
Top Head – from 10 HP to 15 HP (Value $ 720.) .................................................... $ Included
Full Width Driven Bottom Infeed Roll – Spiral Fluted (Value $ 935) ..................... $ Included
Note – We consider this to be a very desirable option under most conditions
It improves feeding by eliminating friction and much less wear to the Infeed Bed.
Pneumatic Roller Side Pressure Unit between the 1st bottom head and the Fence
side head in lieu of spring tensioned holdover – suggested for best controlled operation &
variable pressure to material going through the side heads (Value $ 365.) ………..$ Included
Air Tensioned and operated Top Head Chip Breaker with separate pressure control
(maybe consider for 1st Top if a fair amount of thickness variation of incoming stock)
(Value $ 275.)........................................................................................................... $ Included
SIKO Dual Mechanical Digital Readouts with tool compensation device in lieu of
standard single counters, Included on Near Side and 1 Top
(Value $540. ea x 2 = $1,080.) .............................................................................. ... $ Included
Axial Adjustment of the Last Bottom Head from the front of the moulder with
Digital Position readout (Value $ 395.) ................................................................... $ Included
1 Complete set of carbide spiral Cutterheads ………………………………….….$ Included
1 only dust manifold for 5 head moulder……………………………………………….$ Included
John G. Weber Co.
Page 4 of 10
Actual Machine Photos
John G. Weber Co.
Page 5 of 10
John G. Weber Co.
Page 6 of 10
John G. Weber Co.
Page 7 of 10
John G. Weber Co.
Page 8 of 10