Hose Index

Transcription

Hose Index

SPECIALTY &
TRUCK HOSE
Hose Index
Alphabetical Index
A/C and Refrigeration Hose
17
AQP Hose
13-14
Hose
20-57
Hydraulic
AQP
34-57
35, 36, 39, 40,
41, 45, 48, 49, 50, 51
AQP/HI-IMPULSE 39, 40, 48, 49
AQP/Hi-Pac
41
BRUISER™ 43, 44, 46, 53, 54, 56
Double wire braid
42-49
DESCRIPTION
PAGES
Four spiral wire
49-53
Four or six spiral wire 54-56
HI-IMPULSE
38-40, 47-49
Hi-Pac
41
MatchMate BLUE
39, 48
MatchMate ICE
45
MatchMate Plus 39, 47, 48, 51
Single wire braid
38-42
Textile braid
21, 22, 32-37
Wire inserted suction 34, 35
DESCRIPTION
PAGES
Special application
20-34
Airbrake
21-23
AQP
23-25, 27, 33
Convoluted PTFE
31, 32
Engine and airbrake
23
EPDM
40, 49
Fuel and oil
23-27
Jack Hose
57
LPG
27, 28
DESCRIPTION
PAGES
Power steering
41
Railroad airbrake
22
Silicone rubber (coolant) 20
Silicone rubber (heater)
20
SOCKETLESS
32-34
PTFE
28-32
Textile braid low pressure
32-34, 35-37
How to order
PTFE Hose
Thermoplastic Hose
LOW & MEDIUM
PRESSURE HOSE
PAGES
12
18-19
15-16
HIGH PRESSURE HOSE
DESCRIPTION
PART #
PG.
32
37
37
25
35
38
45
47
28
30
CR170
FC194
FC195
FC234
FC252
FC254
FC273
FC273B
FC300
FC310
28
40
49
25
20
53
54
54
27
41
Eaton’s Aeroquip Hose
and Fitting Assembly
Product Warning
Flexible hose lines offer
many advantages over rigid
tubing including routing
ease, vibration absorption,
sound deafening and the
ability to accommodate
movement of connected
components. However,
hose lines require caution
in use not only to provide
long service, but also to
guard against potentially
dangerous failure.
Important
The user should carefully
observe the precautions
listed in this catalog,
including the recommendations on the selection of
hose and fittings on the relevant pages, and the pages
on fluid compatibility. In
addition, care should be
taken not to exceed the
minimum bend radius listed
for each hose size and type
in the hose section.
PART #
FC321
FC323
FC324
FC325
FC332
FC350
FC352
FC355
FC363
FC364
PG.
PART #
PG.
27
50
50
51
33
23
20
23
31
31
FC465
FC466
FC469
FC498
FC510
FC563
FC579
FC598
FC606
FC606B
29
35
30
36
41
32
57
36
56
56
Maximum operating pressure should not exceed
pressures listed in the hose
data. Instructions for
assembling fittings to different hose should be followed carefully to ensure
the performance of the
completed assembly.
WARNING Eaton
fitting tolerances
are engineered to match
Eaton’s Aeroquip hose
tolerances. The use of
Eaton fittings on hose
supplied by other manufacturers and/or the use of
Eaton’s Aeroquip hose with
fittings supplied by other
manufactures may result in
the production of unreliable
and unsafe hose assemblies and is neither recommended nor authorized by
Eaton Corporation or any of
its affiliates or subsidiaries.
PART #
FC611
FC619
FC629
FC636
FC639
FC647
FC650
FC659
FC693
FC699
PG.
PART #
PG.
PART #
PG.
40
34
21
49
42
33
24
52
46
24
FC735
FC736
FC829
FC839B
FC849
FC849B
FC854
GH120
GH194
GH195
46
53
22
43
43
44
53
45
39
48
GH466
GH493
GH506
GH663
GH681
GH781
GH793
S-TW
55
51
55
39
42
47
48
29
WARNING
Application considerations must be observed in
selecting appropriate components for the application
of these products contained herein. The failure to
follow the recommendations set forth in this catalog may result in an unstable application which may
result in serious personal
injury or property damage.
EATON CORPORATION OR
ANY OF ITS AFFILIATES
OR SUBSIDIARIES SHALL
NOT BE SUBJECT TO AND
DISCLAIMS ANY OBLIGATIONS OR LIABILITIES
(INCLUDING BUT NOT
LIMITED TO ALL CONSEQUENTIAL, INCIDENTIAL
AND CONTINGENT DAMAGES) ARISING FROM
TORT CLAIMS (INCLUDING
WITHOUT LIMITATION
NEGLIGENCE AND STRICT
LIABILITY) OR OTHER THEORIES OF LAW WITH
RESPECT TO ANY HOSE
ASSEMBLIES NOT PRO-
DUCED FROM GENUINE
AEROQUIP HOSE FITTINGS, HOSE AND AEROQUIP APPROVED EQUIPMENT, AND IN CONFORMANCE WITH EATON’S
AEROQUIP PROCESS AND
PRODUCT INSTRUCTIONS
FOR EACH SPECIFIC HOSE
ASSEMBLY.
ADAPTERS &
TUBE FITTINGS
2575
2580
2583
2651
2661
2681
2766
2781
2807
2808
PG.
ACCESSORIES &
ASSEMBLY INSTRUCTIONS
26
26
26
22
22
21
21
34
34
21
PART #
Failure to follow these
processes and product
instructions and limitations
could lead to premature
hose assembly failures
resulting in property damage, serious injury or death.
HOSE ASSEMBLY
EQUIPMENT
302A
303
1503
1531
1531A
2550
2554
2556
2565
2570
PG.
Routing
If the user follows the recommendations on hose line
routing and installation as
provide herein, improved
safety and longer service
life of any hose installation
will result.
EATON Aeroquip Fluid Conveyance Products A-HOOV-MC001-E1 December 2007
APPENDICIES
PART #
HOSE FITTINGS
Part Number Index
11
How to Order
SPECIALTY &
TRUCK HOSE
LOW & MEDIUM
PRESSURE HOSE
HIGH PRESSURE HOSE
HOSE FITTINGS
ADAPTERS &
TUBE FITTINGS
Accurate processing and
prompt delivery of your
order depends on easy
identification of your
requirements. Please
order Aeroquip brand parts
using correct part numbers
as described in this catalog.
Inquiries and orders should
be directed to your
Aeroquip Distributor or:
ACCESSORIES &
Eaton Corporation
14615 Lone Oak Road
Eden Prairie, MN 55344
USA
952/937-9800;
Fax: 952/974-7722
www.hydraulics.eaton.com
Part numbers and
dash sizes
HOSE ASSEMBLY
EQUIPMENT
Dash size designates the
nominal size in 16ths of an
inch. This number immediately follows the part number and is separated from it
with a dash.
Dimensions
APPENDICIES
Dimensions given in this
catalog for Aeroquip products are approximate and
should be used for reference only. Exact dimensional information for a given
product is subject to change
and varying tolerances; contact Eaton directly for full
current information.
12
Cut length hose
WARNING
Hose assemblies
Cut lengths of hose should be ordered as shown below by
specifying lengths in inches.
Eaton manufactures the
terminal ends of our hose
fittings to the appropriate
requirements established
by the SAE. Therefore, the
performance ratings of
these hose fittings meet
the SAE requirements. It is
possible to order a hose
assembly with a fitting terminal end that has a performance rating lower than
the hose rating. When
ordering hose assemblies,
please keep the connecting
end performance rating in
mind since this may affect
overall hose assembly performance.
For numeric part numbers:
Hose assembly components (hose and fittings)
are easily assembled in the
field. However, factory
assembled reusable and
crimped hose assemblies
are available.
For complete information,
contact Eaton.
2651- 10- 00484
Hose type
Hose size (in 16ths of an inch)
Cut length (in inches)
last digit is in 1/8ths of an inch 00484 = 481/2 inches
For alpha-numeric part numbers:
FC300- 08- 00484
Hose type
Hose dash size
Cut length (in inches)
last digit is in 1/8ths of an inch 00484 = 481/2 inches
Bulk hose
Bulk hose should be ordered by specifying length in feet as
shown below.
Complete number
500 ft.- 2651- 10
Quantity (in feet)
Hose type
Hose size (in 16ths of an inch)
Note: Length tolerance for hose, assemblies and sleeves is:
Up to and including 12 inches: ±1/8"
Above 12 inches to and including 18 inches: ±3/16"
Above 18 inches to and including 36 inches: ±1/4"
Above 36 inches: ±1% of length
SPECIALTY &
TRUCK HOSE
AQP Hose
FC300 AQP Hose
The superior high-temperature, abrasion-resistant
hose. Features extensive
fluid compatibility.
See page 27.
Combines superior hightemperature resistance and
extensive fluid compatibility
plus operating pressures up
to 40% greater than
SAE100R1 hose.
Aeroquip brand
HI-IMPULSE hose
construction is a patented
process. Patent number
3,725,167.
Combines superior high
temperature resistance and
extensive fluid compatibility
plus operating pressures up
to 40% greater than
SAE100R2 hose.
Aeroquip brand
HI-IMPULSE hose
construction is a patented
process. Patent number
3,725,167.
Combines the flexibility
and economy of Hi-Pac
hose with the temperature
and fluid compatibility of
AQP hose.
Aeroquip brand Hi-Pac hose
construction is patented.
Patent number 3,463,197.
Uniform Pressure
Spiral Wire
Hose 210,0 BAR [3000 psi]
The features of AQP
construction and spiral
wire reinforcement are
combined in this quality
hose style.
LOW & MEDIUM
PRESSURE HOSE
Refer to AQP Catalog A-HOAQ-MC001-E1 for more information on AQP hose.
FC195 AQP/HI-IMPULSE Hose
Exceeds SAE100R2A, EN853 2ST, ISO1436-1 TYPE 2ST
FC510 AQP/Hi-Pac Hose
See page 40.
HOSE FITTINGS
Exceeds SAE100R1A, EN853 1ST, ISO1436-1 TYPE 1ST
See page 49.
ADAPTERS &
TUBE FITTINGS
FC194 AQP/HI-IMPULSE Hose
HIGH PRESSURE HOSE
Exceeds SAE100R5
See page 41.
FC323 AQP Hose
ACCESSORIES &
Exceeds SAE100R2 Performance Requirements
See page 50.
Uniform Pressure
Spiral Wire Hose
280,0 BAR [4000 psi]
Features the patented AQP
tube compound and 4-spiral
wire reinforcement. Uses
the same fittings as FC323.
HOSE ASSEMBLY
EQUIPMENT
FC324 AQP Hose
See page 50.
Uniform Pressure
Spiral Wire Hose
350,0 BAR [5000 psi]
Features the patented
AQP tube compound and
4-spiral wire reinforcement.
Pressures to 350,0 BAR
[5000 psi].
APPENDICIES
FC325 AQP Hose
See page 51.
13
FC350 AQP Hose
SPECIALTY &
TRUCK HOSE
Exceeds FMVSS-106 Type All
FC355 AQP Hose
LOW & MEDIUM
PRESSURE HOSE
The revolutionary truck
hose with superior abrasion
resistance. Features an
AQP tube for excellent fluid
compatibility and temperature requirements.
See page 23.
Ideal for truck maintenance
and piping conditions
where fluid compatibility
and chemical resistance are
required.
Has a blue AQP elastomer
cover for fluid resistance.
Fire resistant fuel hose
meets USCG AI
requirements. Offers
positive fire resistance in
critical applications without
using a firesleeve.
Offers extended fluid compatibility and operating temperature range for low pressure
applications.
Used with Aeroquip brand
SOCKETLESS fittings for
quick and easy assembly.
For low pressure
applications.
See page 36.
The dual-purpose hose
with extensive fluid compatibility is ideal for either
suction or chemical transfer
applications.
See page 35.
See page 23.
Exceeds FMVSS-106 Type All
FC234 AQP Hose
HIGH PRESSURE HOSE
FC332 AQP SOCKETLESS Hose
HOSE FITTINGS
FC498 AQP Hose
See page 25.
See page 33.
Exceeds SAE100R6
ADAPTERS &
TUBE FITTINGS
2661 AQP Hose
Exceeds SAE100R4
ACCESSORIES &
GH194 MatchMate BLUE AQP/HI-IMPULSE Hose A thin cover, 1-wire version
Exceeds SAE 100R1AT
of AQP/HI-IMPULSE hose
that allows the use of
Aeroquip MatchMate
Plus Thru-The-Cover (TTC)
fittings.
GH195 MatchMate BLUE AQP/HI-IMPULSE Hose A thin cover, 2-wire version
HOSE ASSEMBLY
EQUIPMENT
Exceeds SAE 100R2AT
FC650 AQP Hose
APPENDICIES
High Temperature Fuel and Oil
14
of AQP/HI-IMPULSE hose
that allows the use of
Aeroquip MatchMate Plus
Thru-The-Cover (TTC)
fittings.
The revolutionary truck
hose with superior abrasion
resistance. Features an
AQP tube for excellent fluid
compatibility and temperature requirements.
[3250 psi].
See page 39.
[5750 psi].
See page 48.
Pressure to 70,0 BAR
[1000 psi].
See page 24.
SPECIALTY &
TRUCK HOSE
Synflex Thermoplastic Hose
3R30 Low Pressure Hose
• Low volumetric expansion
• Rugged design
Operating temperature
range of -40°C to +100°C [40°F to 212°F].
• Long continuous lengths
• Low elongation
• Best value 100R7 hose
range of -40°C to +100°C
[-40°F to 212°F].
• SAE J517 non-conductive
hose construction
• Less than 50 microamperes leakage when
subjected to 75,000
volts/ft for 5 minutes
• Flexible in low temperatures
• Abrasion/UV resistant
cover
[-65°F to 212°F].
• Single permanent fitting
series fits all sizes
• SAE 100R7 dimensions
• Cut resistant – heavy
duty design
• Crush resistant
[-45°F to 225°F].
• Highly flexible, even in
cold temperatures
• Small O.D.
• Lightweight, yet rugged
construction
[-65°F to 200°F].
• Long life in impulse
cycling and flexing
• Designed for permanent
or reusable fittings
[-40°F to 212°F].
hose construction.
Less than 50 microamperes leakage when
subjected to 75,000 volts/ft
for 5 minutes
• Long life for impulse
cycling and flexing
• UV resistant cover
and reusable fittings
[-40°F to 212°F].
LOW & MEDIUM
PRESSURE HOSE
Refer to Synflex Catalog E-HOOV-MC001-E for more information on Thermoplastic hose.
3130 Medium Pressure Hose
HIGH PRESSURE HOSE
SAE100R3 Performance Specifications
3580 Medium Pressure Hose
SAE100R1 & R7 Performance Specifications
30CT Constant Pressure Hose
ADAPTERS &
TUBE FITTINGS
SAE100R7 Non-Conductive Requirements, ANSI A92.2 Specs
ACCESSORIES &
37AL Non-Conductive Medium Pressure Hose
HOSE FITTINGS
SAE100R7 Specifications
3R80 High Pressure Hose
HOSE ASSEMBLY
EQUIPMENT
SAE 100R18 Specifications
3E80 Non-Conductive High Pressure Hose
SAE100R8 Specifications
APPENDICIES
SAE 100R8 Specifications
15
SPECIALTY &
TRUCK HOSE
Refer to Synflex Catalog E-HOOV-MC001-E for more information on Thermoplastic hose.
3V10 Very High Pressure Hose
LOW & MEDIUM
PRESSURE HOSE
• Compact size
• Lightweight
• Low elongation
range of -40°C to +66°C [40°F to +150°F].
high pressure fittings
with hose guards
hose construction. Less
than 50 micro-amperes
leakage when subjected to
75,000 volts/ft for 5 minutes
• Compact size
• Low elongation
high pressure fittings
with hose guards
range of -40°C to +66°C [40°F to +150°F].
3630 General Purpose Air and Water Hose
• Standard bold colors:
gray, red, blue, yellow or
black
• Excellent abrasion and
impact resistance
• Lightweight
• 4:1 Burst to working
pressure safety factor
• Long life over rubber
hose
[-10°F to 150°F].
3440 Moisture-Lok Hose
• High moisture barrier
core tube
• No plasticizers in the
core tube
• Custom colors available
[-10°F to 150°F].
34CU High Pressure Transfer Hose
• Higher pressures than
3440 Moisture Lok series
• High moisture barrier
core tube
• High chemical compatibility core tube
• Custom colors available
[-40°F to 212°F].
HIGH PRESSURE HOSE
3VE0 Non-Conductive
Very High Pressure Hose
HOSE FITTINGS
ADAPTERS &
TUBE FITTINGS
ACCESSORIES &
Kynar® Core Tube
HOSE ASSEMBLY
EQUIPMENT
APPENDICIES
16
SPECIALTY &
TRUCK HOSE
FC558 R134a A/C and Refrigeration Hose
For more information,
refer to catalog
A-HOAC-MC001-E1.
Butyl tube and polyester
braid, abraision-resistant
cover. Designed to work
with 100R5 reusable fittings. Temperature range is
40˚C to +121˚C
[-40˚F to +250˚F].
refer to catalog
A-HOAC-MC001-E1.
Hose constructed of
polymide veneer tube,
with synthetic rubber cover.
Designed to work with
100R5 reusable fittings.
Temperature range is
-40˚C to +121˚C
[-40˚F to +250˚F].
refer to catalog
A-HOAC-MC001-E1.
Flexible hose is constructed
of a corrugated polymide
tube for exceptional flexibility in large bus applications.
This is a factory crimp product. Please contact Eaton for
additional information to
qualify for field crimp of the
FC555 hose. Temperature
range is -40˚C to +125˚C
[-40˚F to +257˚F].
Hose constructed of
polymide veneer tube with
polyester reinforcement
and synthetic rubber cover.
The FC505 fitting program
is factory crimp only.
-40˚C to +135˚C
[-40˚F to +275˚F].
HIGH PRESSURE HOSE
Exceeds SAE-J2064, Type E.
Hose constructed of
polymide veneer tube, with
polyester reinforcement and
chlorobutyl cover.
-40˚C to +135˚C
[-40˚F to +275˚F]. Fitting
selection includes factory
crimp and the E-Z Clip line
of A/C connections.
HOSE FITTINGS
GH134 Multi-Refrigerant A/C and
Refrigeration Hose
LOW & MEDIUM
PRESSURE HOSE
Refer to A/C and Refrigeration Catalog A-HOAC-MC001-E1 for more information on A/C and Refrigferation hose.
FC802 Multi-Refrigerant A/C and
Refrigeration Hose
ADAPTERS &
TUBE FITTINGS
Meets SAE J2064 with 100R5 reusable fittings, sizes 10 to 24.
refer to catalog
A-HOAC-MC001-E1.
HOSE ASSEMBLY
EQUIPMENT
FC555 Multi-Refrigerant A/C and
Refrigeration Hose
ACCESSORIES &
SAE-J2064, Type E construction.
Meets SAE-J2064.
refer to catalog
A-HOAC-MC001-E1.
APPENDICIES
FC505 Low Effusion, Multi-Refrigerant
17
PTFE Hose
SPECIALTY &
TRUCK HOSE
Refer to Everflex Catalog E-HOEV-MC001-E for more information on PTFE hose.
Smooth Bore “S” Series Hose
LOW & MEDIUM
PRESSURE HOSE
HIGH PRESSURE HOSE
Smooth Bore “B” Series Hose
HOSE FITTINGS
Smooth Bore “STW” Series Hose
ADAPTERS &
TUBE FITTINGS
Smooth Bore “S-3” Series Hose
ACCESSORIES &
HOSE ASSEMBLY
EQUIPMENT
Smooth Bore “SC” Series Hose
APPENDICIES
18
Everflex S Series tube is
reinforced with 304 stainless steel wire. All sizes
have a minimum of .040”
thick extruded virgin PTFE.
That is 33% more PTFE
than most other manufacturers offer. The additional
PTFE results in improved
bend radius, kink resistance and slows permeation
of gases. Temperature
[-65˚F to +450˚F].
Everflex B Series is reinforced with bronze wire. All
sizes have a minimum of
0.040” thick extended virgin PTFE. Everflex B Series
hose has traditionally been
used in high vibration envi-
ronments. Temperature
[-65˚F to +400˚F].
Everflex STW Series tube is
reinforced with 304 stainless steel wire. STW hose
is available as an alternative
where competitors’ thin
wall products are specified
and S Series hose can not
be substituted. Radius in
inches to inside bend.
Multiply bend radius by 1.25
for dynamic applications.
-54˚C to +230˚C
[-65˚F to +450˚F].
S-3 with a PVC cover is a
PTFE hose which can be
used for DOT 571.106
hydraulic brake line applications. PVC cover is on the
exterior in 0.020” thickness.
The PVC cover is useful to
protect motorcycle paint
jobs or provide durability in
an abrasive environment.
Temperature range is -40˚C
to +93˚C [-40˚F to +200˚F].
SC Series hose is identical
to the S series with one
exception. SC hose has an
internal conductive static
dissipating liner that provides a path to the hose
end fittings for applications
where flow induced electrostatic charges can occur.
Radius in inches to inside
bend. Multiply bend radius by
1.25 for dynamic applications.
to +230˚C [-65˚F to +450˚F].
For more information, refer
to catalog E-HOEV-MC001-E.
to +204˚C [-65˚F to +400˚F].
Convoluted PTFE tube with
304 stainless steel wire
braid reinforcement.
water, tire manufacturing,
electronics, steel mills, food
processing, and tank truck
transfer. Temperature range
is -54˚C to +204˚C [-65˚F to
+400˚F].
LOW & MEDIUM
PRESSURE HOSE
HOSE FITTINGS
HIGH PRESSURE HOSE
ADAPTERS &
TUBE FITTINGS
Industrial applications
include: automotive, platten
presses, pharmaceutical,
truck and bus, reverse
osmosis, hydraulics, chemical processing, steam, air,
SPECIALTY &
TRUCK HOSE
Hi-PSI Series hose is a heavy
wall PTFE hose for very high
pressure applications. The
reinforcement is braided and
not spiraled allowing for better hose flexibility.
ACCESSORIES &
Conductive & Non-Conductive
Convoluted Hose Conv-O-Crimp
static charges can occur.
Radius in inches to inside
bend. Multiply bend radius by
1.25 for dynamic applications.
to +204˚C [-65˚F to +400˚F].
HOSE ASSEMBLY
EQUIPMENT
Smooth Bore “Hi-PSI” Series Hose
SCTW Series hose is identical to the STW Series with
one exception. SCTW hose
has an internal conductive
static dissipating liner that
provides a path to the hose
end fittings for applications
where flow induced electro-
APPENDICIES
Smooth Bore “SCTW” Series Hose
19
SPECIALTY &
TRUCK HOSE
FC252
Silicone rubber (heater)
r
Part Number
LOW & MEDIUM
PRESSURE HOSE
FC252-06
FC252-08
FC252-10
FC252-12
FC252-16
Hose I.D.
mm
in
9,7
12,7
16,0
19,1
25,4
0.38
0.50
0.63
0.75
1.00
HIGH PRESSURE HOSE
Construction
Silicone rubber tube, braided
fiber reinforcement and silicone
rubber cover.
Operating Temperature Range
–54°C to +177°C [–65°F to +350°F]
Hose O.D.
Maximum
Operating
Pressure
mm
in
bar
psi
bar
0.72
0.81
0.94
1.06
1.34
3,5
3,5
2,8
2,8
2,5
50
50
40
40
35
14,0
14,0
11,0
11,0
10,0
18,3
20,6
23,9
26,9
34,0
Application
Heater hose for passenger cars
and trucks; connecting lines from
hot water heaters to coolant-circulating systems. For more information on specific fluid applications and high temperature ratings, see pages 349-355.
Minimum
Burst
Pressure
Minimum
Bend
Radius
psi
mm
200
200
160
160
140
38,1
50,8
63,5
76,2
101,6
Weight
of Hose
in
Kg/m
lbs/ft
1.50
2.00
2.50
3.00
4.00
0,22
0,27
0,28
0,41
0,53
0.15
0.18
0.19
0.28
0.36
For Complete Agency Listings
See pages 346-348.
Fitting Reference
Reusable
Clamp
Page
Fitting Reference
Reusable
Clamp
Page
184
HOSE FITTINGS
FC352
Silicone rubber (coolant)
Part Number
Hose I.D.
ADAPTERS &
TUBE FITTINGS
mm
ACCESSORIES &
FC352-08
FC352-10
FC352-12
FC352-14
FC352-16
FC352-18
FC352-20
FC352-22
FC352-24
FC352-26
FC352-28
FC352-32
FC352-36
FC352-38
FC352-40
FC352-44
FC352-48
FC352-56
FC352-64
FC352-96
FC352-112
HOSE ASSEMBLY
EQUIPMENT
12,7
16,0
19,1
22,4
25,4
28,4
31,8
35,1
38,1
41,4
44,5
50,8
57,2
60,1
63,5
69,9
76,2
88,9
101,6
152,4
177,8
in
0.50
0.63
0.75
0.88
1.00
1.12
1.25
1.38
1.50
1.63
1.75
2.00
2.25
2.38
2.50
2.75
3.00
3.50
4.00
6.00
7.00
APPENDICIES
Construction
Silicone rubber tube, four spirals
of nylon and silicone rubber
cover.
–54°C to +177°C [–65°F to +350°F]
20
Hose O.D.
Maximum
Operating
Pressure
mm
in
bar
psi
bar
psi
Kg/m
0.94
1.06
1.19
1.32
1.44
1.56
1.69
1.82
1.94
2.06
2.19
2.44
2.69
2.82
2.94
3.19
3.44
3.94
4.44
6.47
7.47
7,0
7,0
7,0
7,0
6,0
6,0
5,9
5,9
5,9
5,6
5,6
5,2
5,2
4,2
4,2
3,5
3,5
2,8
2,5
2,0
1,0
100
100
100
100
90
90
85
85
85
80
80
75
75
60
60
50
50
40
35
25
19
30,0
30,0
30,0
30,0
26,0
26,0
24,0
24,0
24,0
22,0
22,0
21,0
21,0
17,0
17,0
14,0
14,0
12,0
10,5
7,0
6,0
425
425
425
425
375
375
350
350
350
325
325
300
300
250
250
200
200
175
150
100
75
0,25
0,32
0,40
0,46
0,50
0,61
0,66
0,74
0,81
0,86
0,93
1,06
1,20
1,24
1,31
1,45
1,56
1,85
2,13
3,45
4,03
23,9
26,9
30,2
33,5
36,6
39,6
42,9
46,2
49,3
52,3
55,6
62,0
68,3
71,6
74,7
81,0
87,4
100,1
112,8
164,3
189,7
Application
Coolant system service with liquid-cooled engines. For more
information on specific fluid
applications and high temperature ratings, see pages 349-355.
Minimum
Burst
Pressure
Weight
of Hose
lbs/ft
0.17
0.22
0.27
0.31
0.34
0.41
0.45
0.50
0.55
0.58
0.63
0.72
0.81
0.84
0.89
0.98
1.06
1.25
1.44
2.34
2.73
See pages 346-348.
184
SPECIALTY &
TRUCK HOSE
2550/2554
Airbrake
SAE J1402 FMVSS106
r
Hose O.D.
Minimum
Bend
Radius
Weight
of Hose
mm
in
mm
in
bar
psi
bar
psi
mm
in
Kg/m
lbs/ft
9,7
9,7
0.38
0.38
19,1
19,1
0.75
0.75
16,0
16,0
225
225
62,0
62,0
900
900
44,5
95,3
1.75
3.75
0,30
0,27
0.20
0.18
Construction
Synthetic rubber tube, double
textile braids and synthetic
rubber cover.
2550: –40°C to +93°C
[–40°F to +200°F],
Application
Tractor to trailer lines, axle chamber lines and tractor service
lines. For more information on
specific fluid applications and
high temperature ratings, see
pages 349-355.
2554: –54°C to +100°C
[–65°F to +212°F]
2554 Conforms to ordinance
spec. MIL-H-3992B,
Type 1, Class 1.
See pages 346-348.
LOW & MEDIUM
PRESSURE HOSE
2550-6
2554-6
Hose I.D.
Minimum
Burst
Pressure
Fitting Reference
Page
Reusable
Fitting
182
Socket Data
65
Factory crimp fittings also
available. Contact Eaton for
details.
HIGH PRESSURE HOSE
Part Number
Maximum
Operating
Pressure
2570
HOSE FITTINGS
SAE J1402 FMVSS106
r
Minimum
Bend
Radius
Weight
of Hose
Hose I.D.
Hose O.D.
mm
in.
mm
in.
bar
psi
bar
psi
mm
in.
Kg/m lbs/ft
9,7
12,7
15,7
0.38
0.50
0.62
19,1
22,4
26,9
0.75
0.88
1.06
16,0
16,0
16,0
225
225
225
62,0
62,0
62,0
900
900
900
44,5
50,8
57,2
1.75
2.00
2.25
0,27
0,34
0,44
Construction
textile braid and synthetic rubber
cover.
–40°C to +100°C [–40°F to +212°F]
Application
pages 349-355.
See pages 346-348.
‡ Crimp Fittings only,
contact Eaton Aeroquip.
0.18
0.23
0.30
ADAPTERS &
TUBE FITTINGS
2570-6
2570-8
2570-10‡
Minimum
Burst
Pressure
Fitting Reference
Page
Reusable
Fitting
182
Socket Data
65
Factory crimp fittings also
available. Contact Eaton for
details.
ACCESSORIES &
Part Number
Maximum
Operating
Pressure
FC629
HOSE ASSEMBLY
EQUIPMENT
SAE J1402 FMVSS106
r
FC629-06
FC629-08
Hose I.D.
Hose O.D.
Minimum
Burst
Pressure
mm
in.
mm
in.
bar
psi
bar
9,7
12,7
0.38
0.50
19,8
23,1
0.78
0.91
15,0
15,0
225
225
62,0
62,0
Construction
Synthetic rubber tube, single
polyester braid and synthetic
rubber cover.
–40°C to +100°C [–40°F to +212°F]
Application
Tractor to trailer lines, axle
chamber lines and tractor service
pages 349-355.
Minimum
Bend
Radius
Weight
of Hose
psi
mm
in.
Kg/m
lbs/ft
900
900
44,5
50,8
1.75
2.00
0,27
0,30
0.18
0.20
See pages 346-348.
Factory crimp fittings available.
Contact Eaton for details.
APPENDICIES
Part Number
Maximum
Operating
Pressure
21
SPECIALTY &
TRUCK HOSE
FC829
Airbrake
SAE J1402 FMVSS106
r
Part Number
LOW & MEDIUM
PRESSURE HOSE
FC829-08
Hose I.D.
Hose O.D.
mm
in.
mm
in.
12,7
0.50
23,1
0.91
Construction
EPDM rubber tube, double textile braids and EPDM rubber
cover.
HIGH PRESSURE HOSE
–40°C to +100°C [–40°F to +212°F]
Maximum
Operating
Pressure
Minimum
Burst
Pressure
Minimum
Bend
Radius
Weight
of Hose
bar
psi
bar
psi
mm
in.
Kg/m
lbs/ft
15
225
62
900
76,2
3.00
0,27
0.18
Application
pages 349-355.
See pages 346-348.
HOSE FITTINGS
1531/1531A
Railroad Airbrake
Exceeds AAR-M618
r
ADAPTERS &
TUBE FITTINGS
Part Number
ACCESSORIES &
1531-10‡
1531-12
1531-16‡
1531-20
1531A-24‡
Hose I.D.
Hose O.D.
Maximum
Operating
Pressure
Minimum
Burst
Pressure
mm
in.
mm
in.
bar
psi
bar
12,7
16,0
22,4
28,7
35,1
0.50
0.63
0.88
1.13
1.38
23,9
28,4
35,1
41,4
47,8
0.94
1.12
1.38
1.63
1.88
21,0
21,0
21,0
21,0
21,0
300
300
300
300
300
84,0
84,0
84,0
84,0
84,0
Construction
Synthetic rubber tube, partial textile braid, wire reinforcement
(1531-10 and 1531-12 have single
wire braid; 1531-16, 1531-20 and
1531A-24 have double wire
braid) and synthetic rubber cover.
Application
Locomotive airbrake lines.
For more information on specific
fluid applications and high
temperature ratings, see pages
349-355.
psi
mm
1200
1200
1200
1200
1200
139,7
165,1
187,5
241,3
266,7
HOSE ASSEMBLY
EQUIPMENT
APPENDICIES
Weight
of Hose
in.
Kg/m
lbs/ft
5.50
6.50
7.38
9.50
10.50
0,57
0,71
1,07
1,16
1,55
0.38
0.48
0.72
0.78
1.04
See pages 346-348.
–54°C to +100°C [–65°F to +212°F]
22
Minimum
Bend
Radius
Fitting Reference
Page
Reusable
Fitting
185
Socket Data
65
‡ Crimp fittings also available
for these sizes. Contact
Eaton for information.
SPECIALTY &
TRUCK HOSE
FC355 AQP
Engine & Airbrake
FMVSS106
mm
in
4,8
6,4
7,9
10,4
12,7
16,0
22,4
28,7
35,1
46,0
0.19
0.25
0.31
0.41
0.50
0.63
0.88
1.13
1.38
1.81
Construction
AQP elastomer tube, polyester
inner braid and a single wire
braid reinforcement, blue AQP
elastomer cover.
–40°C to +150°C [–40°F to +302°F]
Hose O.D.
mm
13,2
14,7
17,3
19,6
23,9
27,4
31,5
38,6
44,5
56,4
in
0.52
0.58
0.68
0.77
0.94
1.08
1.24
1.52
1.75
2.22
bar
psi
bar
105,0
105,0
105,0
87,0
87,0
52,0
28,0
21,0
17,0
14,0
1500
1500
1500
1250
1250
750
400
300
250
200
420,0
420,0
420,0
350,0
350,0
210,0
112,0
87,0
70,0
56,0
Application
Air, gasoline, fuel, lubricating oils
and coolants. For more information on specific fluid applications
and high temperature ratings,
see pages 349-355.
psi
6000
6000
6000
5000
5000
3000
1600
1250
1000
800
mm
19,1
25,4
31,8
44,5
57,2
69,9
88,9
114,3
139,7
215,9
Vacuum
Service
in
kPa
0.75
1.00
1.25
1.75
2.25
2.75
3.50
4.50
5.50
8.50
94,8
94,8
94,8
94,8
94,8
67,7
50,8
50,8
37,2
37,2
See pages 346-348.
Weight
of Hose
in/Hg
Kg/m
lbs/ft
28
28
28
28
28
20
15
15
11
11
0,22
0,34
0,35
0,43
0,59
0,68
0,74
0,87
1,02
1,37
0.17
0.20
0.24
0.29
0.40
0.46
0.50
0.59
0.69
0.93
Fitting Reference
Crimp
100R5
Reusable
Fitting
Socket Data
HIGH PRESSURE HOSE
FC355-04
FC355-05
FC355-06
FC355-08
FC355-10
FC355-12
FC355-16
FC355-20
FC355-24
FC355-32
Hose I.D.
Minimum
Bend
Radius
Page
134
HOSE FITTINGS
Part Number
Minimum
Burst
Pressure
LOW & MEDIUM
PRESSURE HOSE
r
Maximum
Operating
Pressure
136
65
ADAPTERS &
TUBE FITTINGS
Air not to exceed 250 psi or
+121°C [+250°F].
FC350 AQP
Engine & Airbrake
FMVSS106
mm
in
4,8
6,4
7,9
10,4
12,7
16,0
22,4
28,4
35,1
0.19
0.25
0.31
0.41
0.50
0.63
0.88
1.12
1.38
Construction
inner braid and a single wire
braid reinforcement; black polyester textile braided cover.
–49°C to +150°C [–55°F to +302°F]
Hose O.D.
mm
13,2
14,7
17,3
19,6
23,9
27,4
31,2
38,1
44,5
in
0.52
0.58
0.68
0.77
0.94
1.08
1.23
1.50
1.75
bar
psi
bar
140,0
105,0
105,0
87,0
87,0
52,0
28,0
21,0
17,0
2000
1500
1500
1250
1250
750
400
300
250
560,0
420,0
420,0
350,0
350,0
210,0
112,0
84,0
70,0
Application
Air, gasoline, fuel lubricating oils
and coolants. For more information on specific fluid applications
see pages 349-355.
psi
8000
6000
6000
5000
5000
3000
1600
1200
1000
mm
19,1
25,4
31,8
44,5
57,2
69,9
88,9
114,3
139,7
Vacuum
Service
in
kPa
0.75
1.00
1.25
1.75
2.25
2.75
3.50
4.50
5.50
94,8
94,8
94,8
94,8
94,8
67,7
50,8
50,8
37,2
See pages 346-348.
Weight
of Hose
in/Hg
Kg/m
lbs/ft
28
28
28
28
28
20
15
15
11
0,22
0,34
0,35
0,43
0,59
0,68
0,74
0,87
1,02
0.13
0.16
0.20
0.23
0.33
0.39
0.50
0.56
0.63
Fitting Reference
Crimp
100R5
Reusable
Fitting
Socket Data
HOSE ASSEMBLY
EQUIPMENT
FC350-04
FC350-05
FC350-06
FC350-08
FC350-10
FC350-12
FC350-16
FC350-20
FC350-24
Hose I.D.
Minimum
Bend
Radius
Page
134
APPENDICIES
Part Number
Minimum
Burst
Pressure
ACCESSORIES &
r
Maximum
Operating
Pressure
136
65
Air not to exceed +121°C
[+250°F].
23
SPECIALTY &
TRUCK HOSE
FC650 AQP
High temperature fuel & oil
r
Part Number
LOW & MEDIUM
PRESSURE HOSE
FC650-04
FC650-06
FC650-08
FC650-10
FC650-12
Hose I.D.
mm
in
4,8
7,9
10,4
12,7
16,0
0.19
0.31
0.41
0.50
0.63
HIGH PRESSURE HOSE
Construction
AQP elastomer tube, single wire
braid reinforcement, black polyester braided cover.
–49°C to +150°C [–55°F to +302°F]
[+250°F].
Hose O.D.
mm
12,2
16,0
18,8
21,1
25,1
Maximum
Operating
Pressure
Minimum
Burst
Pressure
in
bar
psi
bar
0.48
0.63
0.74
0.83
0.99
70,0
70,0
70,0
70,0
70,0
1000
1000
1000
1000
1000
280,0
280,0
280,0
280,0
280,0
Application
Diesel fuel, gasoline, lubricating
oils, water, coolant and air. Not
approved for airbrake applications. For more information on
pages 349-355.
Minimum
Bend
Radius
Vacuum
Service
psi
mm
in
kPa
4000
4000
4000
4000
4000
19,1
31,8
44,5
57,2
69,9
0.75
1.25
1.75
2.25
2.75
94,8
94,8
94,8
94,8
67,7
See pages 346-348.
Weight
of Hose
in/Hg
Kg/m
lbs/ft
28
28
28
28
20
0,15
0,22
0,28
0,34
0,41
0.10
0.15
0.19
0.23
0.28
HOSE FITTINGS
ADAPTERS &
TUBE FITTINGS
FC699 AQP
High temperature fuel
AQP lightweight engine hose
ACCESSORIES &
r
Part Number
HOSE ASSEMBLY
EQUIPMENT
FC699-04
FC699-06
FC699-08
FC699-10
FC699-12
FC699-16
Hose I.D.
mm
in
6,4
9,7
12,7
16,0
19,1
25,4
0.25
0.38
0.50
0.63
0.75
1.00
Construction
AQP elastomer tube, single
aramid reinforcement braid and
textile braided cover.
–40°C to +150°C [–40°F to +302°F].
Hose O.D.
mm
12,4
16,0
19,6
23,9
27,4
33,8
Maximum
Operating
Pressure
in
bar
0.49
0.63
0.77
0.94
1.08
1.33
28,0
28,0
28,0
24,0
24,0
17,0
psi
400
400
400
350
350
250
Application
Diesel fuel, gasoline, crude and
lubricating oils. For more information on specific fluid applications
see pages 349-355.
Minimum
Burst
Pressure
bar
112,0
112,0
112,0
98,0
98,0
70,0
psi
1600
1600
1600
1400
1400
1000
mm
31,8
38,1
50,8
63,5
76,2
114,3
APPENDICIES
Vacuum
Service
in
kPa
1.25
1.50
2.00
2.50
3.00
4.50
94,8
94,8
94,8
61,0
61,0
61,0
See pages 346-348.
Air not to exceed 250 psi or
+121°C [+250°F].
24
Minimum
Bend
Radius
Weight
of Hose
in/Hg
Kg/m
lbs/ft
28
28
28
18
18
18
0,09
0,15
0,19
0,27
0,30
0,41
0.06
0.10
0.13
0.18
0.20
0.28
Fitting Reference
Crimp
OTC
Page
66
SPECIALTY &
TRUCK HOSE
FC234 AQP
High temperature fuel and oil
Fire resistant USCG/MMT, NMMA/BIA
mm
in
6,4
7,9
10,4
12,7
16,0
22,4
0.25
0.31
0.41
0.50
0.63
0.88
Construction
AQP elastomer tube, brass plated steel wire reinforcement,
braided refractory insulation and
blue AQP elastomer cover.
–40°C to +150°C [–40°F to +302°F]
Hose O.D.
mm
14,7
17,3
19,3
23,9
27,4
31,5
in
0.58
0.68
0.76
0.94
1.08
1.24
bar
psi
bar
105,0
105,0
87,0
87,0
52,0
28,0
1500
1500
1250
1250
750
400
420,0
420,0
350,0
350,0
210,0
112,0
Application
Diesel fuel, gasoline, hot lube oil
and water. For more information
on specific fluid applications and
pages 349-355.
Vacuum
Service
psi
mm
in
kPa
6000
6000
5000
5000
3000
1600
25,4
31,8
44,5
57,2
69,9
88,9
1.00
1.25
1.75
2.25
2.75
3.50
94,8
94,8
94,8
94,8
67,7
54,2
See pages 346-348.
Weight
of Hose
in/Hg
Kg/m
lbs/ft
28
28
28
28
20
16
0,32
0,37
0,44
0,66
0,71
0,75
0.22
0.25
0.30
0.45
0.48
0.51
Fitting Reference
Crimp
100R5
Reusable
Fitting
Socket Data
HIGH PRESSURE HOSE
FC234-05
FC234-06
FC234-08
FC234-10
FC234-12
FC234-16
Hose I.D.
Minimum
Bend
Radius
Page
134
136
65
HOSE FITTINGS
Part Number
Minimum
Burst
Pressure
LOW & MEDIUM
PRESSURE HOSE
r
Maximum
Operating
Pressure
2651
Single wire braid
ADAPTERS &
TUBE FITTINGS
SAE 100R5 performance
r
in
4,8
6,4
7,9
10,4
12,7
16,0
22,4
28,4
35,1
46,0
60,1
0.19
0.25
0.31
0.41
0.50
0.63
0.88
1.12
1.38
1.81
2.38
Construction
Synthetic rubber tube, textile
inner braid, single wire braid reinforcement, outer textile braid and
synthetic rubber cover.
–40°C to +100°C [–40°F to +212°F]
mm
13,2
14,7
17,3
19,1
23,4
27,4
31,2
38,1
44,5
56,4
73,2
in
0.52
0.58
0.68
0.75
0.92
1.08
1.23
1.50
1.75
2.22
2.88
bar
psi
bar
psi
210,0
210,0
157,0
140,0
122,0
105,0
56,0
43,0
35,0
24,0
24,0
3000
3000
2250
2000
1750
1500
800
625
500
350
350
840,0
840,0
630,0
560,0
490,0
420,0
224,0
175,0
140,0
98,0
98,0
12000
12000
9000
8000
7000
6000
3200
2500
2000
1400
1400
Application
Hydraulics, gasoline, fuel and
lubricating oils, air and water. Air
not to exceed 250 psi or +71°C
[+160°F]. For more information
pages 349-355.
mm
in
76,2 3.00
85,9 3.38
101,6 4.00
117,3 4.62
139,7 5.50
165,1 6.50
187,5 7.38
228,6 9.00
266,7 10.50
336,6 13.25
609,6 24.00
See pages 346-348.
†Maximum negative pressures
shown for -16 and larger are suitable for hose which has suffered
no external damage or kinking. If
greater negative pressures are
required for -16 and larger hoses,
the use of an internal support coil
is recommended.
Vacuum
Service
kPa
94,8
94,8
94,8
94,8
94,8
94,8
67,7
67,7
50,8
37,3
37,3
Weight
of Hose
in/Hg
Kg/m
lbs/ft
28
28
28
28
28
28
20†
20†
15†
11†
11†
0,19
0,24
0,34
0,38
0,55
0,68
0,65
0,77
0,99
1,39
2,11
0.13
0.16
0.23
0.26
0.37
0.46
0.44
0.52
0.67
0.94
1.43
Fitting Reference
Reusable
Fitting
Socket Data
ACCESSORIES &
mm
Hose O.D.
Minimum
Bend
Radius
HOSE ASSEMBLY
EQUIPMENT
2651-4
2651-5
2651-6
2651-8
2651-10
2651-12
2651-16
2651-20
2651-24
2651-32
2651-40
Hose I.D.
Minimum
Burst
Pressure
Page
136
65
APPENDICIES
Part Number
Maximum
Operating
Pressure
25
SPECIALTY &
TRUCK HOSE
303/302A
Single wire braid
MIL-DTL-8794
r
LOW & MEDIUM
PRESSURE HOSE
Part Number
HIGH PRESSURE HOSE
303-4
303-5
303-6
303-8
303-10
303-12
302A-16
302A-20
302A-24
302A32
Hose I.D.
mm
in
4,8
6,4
7,9
10,4
12,7
16,0
22,4
28,4
35,1
46,0
0.19
0.25
0.31
0.41
0.50
0.63
0.88
1.12
1.38
1.81
Construction
Synthetic rubber tube, textile inner
braid, single wire braid reinforcement and black textile braid cover.
HOSE FITTINGS
303 hose: –54°C to +121°C
[65°F to +250°F]
Hose O.D.
mm
13,2
14,7
17,3
19,6
23,4
27,4
31,2
38,1
44,5
56,4
in
0.52
0.58
0.68
0.77
0.92
1.08
1.23
1.50
1.75
2.22
Maximum
Operating
Pressure
Minimum
Burst
Pressure
bar
psi
bar
psi
210,0
210,0
140,0
140,0
122,0
105,0
56,0
42,0
35,0
24,0
3000
3000
2000
2000
1750
1500
800
600
500
350
840,0
700,0
630,0
560,0
490,0
420,0
224,0
175,0
140,0
98,0
12000
10000
9000
8000
7000
6000
3200
2500
2000
1400
Application
Hydraulics, air, gasoline, fuel and
lubricating oils. Air not to exceed
+71°C [+160°F]. For more information on specific fluid applications and high temperature ratings, see pages 349-355.
Minimum
Bend
Radius
mm
in
76,2 3.00
85,9 3.38
101,6 4.00
117,3 4.62
139,7 5.50
165,1 6.50
187,5 7.38
228,6 9.00
279,4 11.00
336,6 13.25
See pages 346-348.
Vacuum
Service
kPa
94,8
94,8
94,8
94,8
94,8
94,8
94,8
94,8
94,8
94,8
Weight
of Hose
in/Hg
Kg/m
lbs/ft
28
28
28
28
28
28
28
28
28
28
0,22
0,28
0,32
0,38
0,53
0,62
0,55
0,68
0,81
1,15
0.15
0.19
0.22
0.26
0.36
0.46
0.44
0.52
0.67
0.94
Fitting Reference
Reusable
Fitting
Socket Data
Page
136
65
302A hose: –40°C to +121°C
[–40°F to +250°F]
ADAPTERS &
TUBE FITTINGS
1503
Single wire braid
SAE 100R5
r
ACCESSORIES &
Part Number
HOSE ASSEMBLY
EQUIPMENT
1503-4
1503-5
1503-6
1503-8
1503-10
1503-12
1503-16
1503-20
1503-24
1503-32
1503-40
Hose I.D.
mm
in
4,8
6,4
7,9
10,4
12,7
16,0
22,4
28,4
35,1
46,0
60,1
0.19
0.25
0.31
0.41
0.50
0.63
0.88
1.12
1.38
1.81
2.38
Construction
Synthetic rubber tube, textile inner
braid, single wire braid reinforcement and black textile braid cover.
APPENDICIES
–40°C to +121°C [–40°F to +250°F]
Air not to exceed
+71°C ([+160°F].
26
Hose O.D.
mm
13,2
14,7
17,3
19,6
23,4
27,4
31,2
38,1
44,5
56,6
73,2
in
0.52
0.58
0.68
0.77
0.92
1.08
1.23
1.50
1.75
2.23
2.88
Maximum
Operating
Pressure
Minimum
Burst
Pressure
bar
psi
bar
psi
210,0
210,0
157,0
140,0
122,0
105,0
56,0
43,0
35,0
24,0
24,0
3000
3000
2250
2000
1750
1500
800
625
500
350
350
840,0
840,0
630,0
560,0
490,0
420,0
224,0
175,0
140,0
98,0
98,0
12000
12000
9000
8000
7000
6000
3200
2500
2000
1400
1400
Application
Hydraulics, air, gasoline, fuel and
lubricating oils. For more information on specific fluid applications
and high temperature ratings, see
pages 349-355.
Minimum
Bend
Radius
mm
in
76,2 3.00
85,9 3.38
101,6 4.00
117,3 4.62
139,7 5.50
165,1 6.50
187,5 7.38
228,6 9.00
266,7 10.50
366,6 13.25
609,6 24.00
†Maximum negative pressures
shown for -16 and larger are suitable only for those which has suffered no external damage or kinking. If greater negative pressures
are required for -16 and larger
hoses, the use of an internal
support coil is recommended.
See pages 346-348.
Vacuum
Service
kPa
94,8
94,8
94,8
94,8
94,8
94,8
67,7
67,7
50,8
37,3
37,3
Weight
of Hose
in/Hg
Kg/m
lbs/ft
28
28
28
28
28
28
20†
20†
15†
11†
11†
0,19
0,24
0,27
0,32
0,49
0,58
0,55
0,68
0,92
1,28
2,11
0.13
0.16
0.23
0.26
0.37
0.46
0.44
0.52
0.67
0.94
1.43
Fitting Reference
Crimp
100R5
Reusable
Fitting
Socket Data
Page
134
136
65
SPECIALTY &
TRUCK HOSE
FC300 AQP
Single wire braid
Exceeds SAE 100R5
r
in
4,8
6,4
7,9
10,4
12,7
16,0
22,4
28,4
35,1
46,0
60,1
0.19
0.25
0.31
0.41
0.50
0.63
0.88
1.12
1.38
1.81
2.38
Construction
inner braid, single wire braid reinforcement and blue polyester
braid cover.
–49°C to +150°C [–55°F to +302°F]
Air not to exceed
+121°C [+250°F].
mm
13,2
14,7
17,3
19,6
23,4
27,4
31,2
38,1
44,5
56,4
73,2
in
0.52
0.58
0.67
0.76
0.93
1.08
1.27
1.50
1.75
2.22
2.88
bar
psi
bar
psi
210,0
210,0
157,0
140,0
122,0
105,0
56,0
43,0
35,0
21,0
21,0
3000
3000
2250
2000
1750
1500
800
625
500
300
300
840,0
840,0
630,0
560,0
490,0
420,0
224,0
175,0
140,0
84,0
84,0
12000
12000
9000
8000
7000
6000
3200
2500
2000
1200
1200
Application
Hydraulics handling petroleum
base fluids and air, gasoline, fuel
and lubricating oils, fire resistant
hydraulic fluids and other industrial fluids. For more information
high temperature ratings,
see pages 349-355.
mm
in
Vacuum
Service
kPa
76,2 3.00
85,9 3.38
101,6 4.00
117,3 4.62
139,7 5.50
165,1 6.50
187,5 7.38
228,6 9.00
266,7 10.50
336,6 13.25
609,6 24.00
†Maximum negative pressure
shown for -16 and larger are suitable for those which has suffered
no external damage or kinking. If
is recommended.
‡ Does not meet SAE 100R5
pressure with reusable fittings.
-32 size rated to 350 psi with
crimp fittings.
Weight
of Hose
in/Hg
Kg/m
lbs/ft
28
28
28
28
28
28
20†
20†
15†
11†
8†
0,19
0,24
0,27
0,32
0,49
0,58
0,55
0,68
0,92
1,28
2,11
0.13
0.16
0.23
0.26
0.37
0.46
0.44
0.52
0.67
0.94
1.50
94,8
94,8
94,8
94,8
94,8
94,8
67,7
67,7
50,8
37,3
27,1
Fitting Reference
Crimp
100R5
Reusable
Fitting
Socket Data
LOW & MEDIUM
PRESSURE HOSE
mm
Hose O.D.
Minimum
Bend
Radius
HIGH PRESSURE HOSE
FC300-04
FC300-05
FC300-06
FC300-08
FC300-10
FC300-12
FC300-16
FC300-20
FC300-24
FC300-32‡
FC300-40‡
Hose I.D.
Minimum
Burst
Pressure
Page
134
HOSE FITTINGS
Part Number
Maximum
Operating
Pressure
136
65
ADAPTERS &
TUBE FITTINGS
See pages 346-348.
ACCESSORIES &
FC321
LPG
UL listing MH6044
r
mm
in
4,8
6,4
7,9
10,4
12,7
16,0
22,4
0.19
0.25
0.31
0.41
0.50
0.63
0.88
Construction
Synthetic rubber tube, a textile
inner braid, a stainless steel wire
braid reinforcement and a synthetic rubber impregnated textile
braid cover.
–40°C to +121°C [–40°F to +250°F]
Hose O.D.
mm
13,2
14,7
17,0
19,6
23,4
27,4
31,5
in
bar
psi
bar
0.52
0.58
0.67
0.77
0.92
1.08
1.24
24,0
24,0
24,0
24,0
24,0
24,0
24,0
350
350
350
350
350
350
350
122,0
122,0
122,0
122,0
122,0
122,0
122,0
Application
Designed for butane-propane
applications on either mobile or
stationary equipment. For more
Minimum
Bend
Radius
Weight
of Hose
psi
mm
in
Kg/m
lbs/ft
1750
1750
1750
1750
1750
1750
1750
38,1
44,5
50,8
58,7
69,9
82,6
93,7
1.50
1.75
2.00
2.31
2.75
3.25
3.69
0,16
0,19
0,27
0,31
0,43
0,55
0,56
0.11
0.13
0.18
0.21
0.29
0.37
0.38
WARNING: LPG is a very hazardous liquid or gas and should be
handled with maximum care to
prevent leakage. Since the gas is
heavier than air, it may flow along
the ground if it escapes and cause
an explosion or a fire. No leakage
should ever be tolerated.
Fitting Reference
Reusable
Fitting
Socket Data
HOSE ASSEMBLY
EQUIPMENT
FC321-04
FC321-05
FC321-06
FC321-08
FC321-10
FC321-12
FC321-16
Hose I.D.
Minimum
Burst
Pressure
Page
136
65
APPENDICIES
Part Number
Maximum
Operating
Pressure
See pages 346-348.
27
SPECIALTY &
TRUCK HOSE
CR170
LPG
Single stainless steel braid
CGA (Canadian Gas Association) Type III
r
LOW & MEDIUM
PRESSURE HOSE
Part Number
CR170-04
CR170-06
CR170-08
CR170-12
Hose I.D.
mm
in
4,8
7,9
10,4
15,9
0.19
0.31
0.41
0.63
HIGH PRESSURE HOSE
Construction
Nylon tube, single stainless steel
braid reinforcement, perforated
–40°C to +121°C [–40°F to +250°F]
Hose O.D.
mm
13,2
17,0
19,6
28,0
Maximum
Operating
Pressure
Minimum
Burst
Pressure
Minimum
Bend
Radius
in
bar
psi
bar
psi
mm
0.52
0.67
0.77
1.10
24,0
24,0
24,0
24,0
350
350
350
350
840,0 12000
630,0 9000
560,0 8000
414,0 6000
76,2
101,6
117,3
165,1
Application
LPG (propane) vehicle, alternative fuel conversion systems. For
more information on specific
fluid applications and high temperature ratings, see pages
349-355.
Weight
of Hose
in
Kg/m
lbs/ft
3.00
4.00
4.62
6.50
0,24
0,32
0,38
0,71
0.16
0.22
0.26
0.48
WARNING: LPG is a very hazardous liquid or gas and should be
handled with maximum care to
prevent leakage. Since the gas is
heavier than air, it may flow along
the ground if it escapes and cause
an explosion or a fire. No leakage
should ever be tolerated.
See pages 346-348.
HOSE FITTINGS
NOTE: Must be CGA certified to
crimp assemblies.
2807
PTFE
SAE 100R14A
ADAPTERS &
TUBE FITTINGS
r
Part Number
ACCESSORIES &
HOSE ASSEMBLY
EQUIPMENT
2807-3
2807-4
2807-5
2807-6
2807-8
2807-10
2807-12
2807-16
2807-20
Hose I.D.
mm
in
3,6
4,8
6,6
8,1
10,7
13,0
16,3
22,4
28,4
0.14
0.19
0.26
0.32
0.42
0.51
0.64
0.88
1.12
Construction
Extruded PTFE tube with stainless steel single wire braid.
–73°C to +260°C [–100°F to +500°F]
Hose O.D.
mm
6,4
7,6
9,4
10,9
13,7
16,0
19,3
26,2
32,8
in
0.25
0.30
0.37
0.43
0.54
0.63
0.76
1.03
1.29
Maximum
Operating
Pressure
bar
psi
bar
psi
210,0
210,0
210,0
175,0
140,0
105,0
84,0
70,0
43,0
3000
3000
3000
2500
2000
1500
1200
1000
625
840,0
840,0
840,0
700,0
560,0
420,0
335,0
280,0
175,0
12000
12000
12000
10000
8000
6000
4800
4000
2500
Application
Hot air, steam, compressor discharge and most chemical applications. Not recommended for
steam-cold water cycling. For
more information on specific fluid
APPENDICIES
† Steam 200 psi at +388°F max.
Engineering information is available for specific critical temperature requirements. Contact Eaton.
28
Minimum
Burst
Pressure
Minimum
Bend
Radius
mm
in
38,1 1.50
50,8 2.00
76,2 3.00
101,6 4.00
133,4 5.25
165,1 6.50
196,9 7.75
228,6 9.00
406,4 16.00
‡Maximum negative pressure for 06 and larger are suitable for hose
which has suffered no external
damage or kinking. If greater negative pressures are required for 06 and larger hoses, the use of an
internal support coil is recommended. Use of an internal support coil in -06 and larger PTFE
hose is recommended for tube
support where extended or continuous service at high temperature together with low or negative
pressure is expected.
See pages 346-348.
Vacuum
Service
kPa
94,8
94,8
94,8
94,8‡
94,8‡
94,8‡
94,8‡
40,6‡
40,6‡
Weight
of Hose
in/Hg
Kg/m
lbs/ft
28
28
28
28‡
28‡
28‡
28‡
12‡
12‡
0,06
0,09
0,12
0,15
0,18
0,24
0,27
0,39
0,51
0.04
0.06
0.08
0.10
0.12
0.16
0.18
0.26
0.34
Fitting Reference
Crimp
Fitting
Socket Data
Reusable
Fitting
Socket Data
Page
129
64
186
65
SPECIALTY &
TRUCK HOSE
S-TW Series
Smooth Bore
Meets SAE 100R14A
r
in
4,8
6,6
8,1
10,7
13,0
16,3
22,4
0.19
0.26
0.32
0.42
0.51
0.64
0.88
Construction
Extruded PTFE tube with stainless steel single wire braid.
–54°C to +230°C [–65°F to +450°F]
mm
7,6
9,4
10,9
13,7
16,0
19,3
26,2
in
0.30
0.37
0.43
0.54
0.63
0.76
1.03
bar
psi
bar
psi
mm
210,0
210,0
175,0
140,0
105,0
84,0
70,0
3000
3000
2500
2000
1500
1200
1000
840,0
840,0
700,0
560,0
420,0
335,0
280,0
12000
12000
10000
8000
6000
4800
4000
50,8
76,2
101,6
127,0
165,1
190,5
228,6
Application
Hot air, steam, compressor discharge and most chemical applications. Not recommended for
applications and high temperature
ratings, see pages 349-355.
Vacuum
Service
in
kPa
2.00
3.00
4.00
5.00
6.50
7.50
9.00
94,8
94,8
94,8‡
94,8‡
94,8‡
94,8‡
40,6‡
‡ Maximum negative pressure for
-16 and larger are suitable for
hose which has sufferend no
external damage or kinking. If
is recommended. Use of an internal support coil in -06 and larger
PTFE hose is recommended for
tube support where extended or
continuous service at high temperature together with low or negative pressure is expected.
See pages 346-348.
Weight
of Hose
in/Hg
Kg/m
lbs/ft
28
28
28‡
28‡
28‡
28‡
12‡
0,09
0,12
0,15
0,18
0,24
0,27
0,35
0.06
0.08
0.10
0.12
0.16
0.18
0.26
Fitting Reference
Crimp
Fitting
Socket Data
Reusable
Fitting
Socket Data
LOW & MEDIUM
PRESSURE HOSE
mm
Hose O.D.
Minimum
Bend
Radius
HIGH PRESSURE HOSE
S-4TW
S-5TW
S-6TW
S-8TW
S-10TW
S-12TW
S-16TW
Hose I.D.
Minimum
Burst
Pressure
Page
129
64
186
65
* See Everflex catalog
E-HOEV-MC001-E for additional
hose sizes and fitting options.
HOSE FITTINGS
Part Number
Maximum
Operating
Pressure
ADAPTERS &
TUBE FITTINGS
FC465
PTFE
Conductive SAE 100R14B
FDA Compliant per 21CFR178.3297
r
in
3,6
4,8
6,6
8,1
10,7
13,0
16,3
22,4
28,4
0.14
0.19
0.26
0.32
0.42
0.51
0.64
0.88
1.12
Construction
Conductive extruded black PTFE
tube with stainless steel single
wire braid.
–73°C to +260°C [–100°F to +500°F]
mm
6,4
7,6
9,4
10,9
13,7
16,0
19,3
26,2
32,8
in
0.25
0.30
0.37
0.43
0.54
0.63
0.76
1.03
1.29
bar
psi
bar
psi
210,0
210,0
210,0
175,0
140,0
105,0
84,0
70,0
43,0
3000
3000
3000
2500
2000
1500
1200
1000
625
840,0
840,0
840,0
700,0
560,0
420,0
335,0
280,0
175,0
12000
12000
12000
10000
8000
6000
4800
4000
2500
Application
Steam, compressor discharge and
most chemical applications. Not
recommended for steam-cold
water cycling. For more information on specific fluid applications
and high temperature ratings, see
pages 349-355.
†Steam 200 psi at +388°F max.
Engineering information is available
for specific critical temperature
requirements. Contact Eaton.
mm
in
38,1 1.50
50,8 2.00
76,2 3.00
101,6 4.00
133,4 5.25
165,1 6.50
196,9 7.75
228,6 9.00
406,4 16.00
damage or kinking. If greater negative pressures are required for -06
and larger hoses, the use of an
internal support coil is recommended. Use of an internal support coil
in -06 and larger PTFE hose is recommended for tube support where
extended or continuous service at
high temperature together with low
or negative pressure is expected.
Vacuum
Service
kPa
94,8
94,8
94,8
94,8‡
94,8‡
94,8‡
94,8‡
40,6‡
40,6‡
Weight
of Hose
in/Hg
Kg/m
lbs/ft
28
28
28
28‡
28‡
28‡
28‡
12‡
12‡
0,06
0,09
0,12
0,15
0,18
0,24
0,27
0,39
0,51
0.04
0.06
0.08
0.10
0.12
0.16
0.18
0.26
0.34
Fitting Reference
Crimp
Fitting
Socket Data
Reusable
Fitting
Socket Data
ACCESSORIES &
mm
Hose O.D.
Minimum
Bend
Radius
HOSE ASSEMBLY
EQUIPMENT
FC465-03
FC465-04
FC465-05
FC465-06
FC465-08
FC465-10
FC465-12
FC465-16
FC465-20
Hose I.D.
Minimum
Burst
Pressure
Page
129
64
186
65
APPENDICIES
Part Number
Maximum
Operating
Pressure
See pages 346-348.
29
SPECIALTY &
TRUCK HOSE
2808
PTFE
r
Part Number
LOW & MEDIUM
PRESSURE HOSE
2808-08
2808-10
2808-12
2808-16
2808-20
2808-24
Hose I.D.
mm
in
10,7
12,9
16,5
22,3
28,4
35,0
0.42
0.51
0.65
0.88
1.12
1.38
HIGH PRESSURE HOSE
Construction
Extruded PTFE tube with double
stainless steel braids.
–73°C to +260°C [–100°F to +500°F]
Hose O.D.
mm
14,7
17,3
20,6
27,7
34,3
41,1
in
0.58
0.68
0.81
1.09
1.35
1.62
Maximum
Operating
Pressure
Minimum
Burst
Pressure
bar
psi
bar
psi
190,0
172,0
121,0
103,0
78,0
55,0
2750
2500
1750
1500
1125
800
758,0
689,0
483,0
414,0
310,0
221,0
11000
10000
7000
6000
4500
3200
HOSE FITTINGS
Application
Hot air, steam and most chemical applications. Not recommended for steam-cold water
cycling. For more information on
high temperatre ratings, see
pages 400-404.
Engineering information is available for specific critical temperature requirements.
Contact Eaton.
Minimum
Bend
Radius
mm
in
117,3 4.62
139,7 5.50
165,1 6.50
187,4 7.38
279,4 11.00
355,6 14.00
damage or kinking. If greater negative pressures are required for 08 and larger hoses, the use of an
internal support coil is recommended. Use of an internal support coil in -08 and larger PTFE
hose is recommended for tube
support where extended or continuous service at high temperature together with low or negative
See pages 397-398.
Vacuum
Service
kPa
94,8‡
94,8‡
67,7‡
50,8‡
50,8‡
50,8‡
Weight
of Hose
in/Hg
Kg/m
lbs/ft
28‡
28‡
20‡
15‡
15‡
15‡
0,30
0,39
0,45
0,65
0,85
1,04
0.20
0.26
0.30
0.44
0.57
0.70
Fitting Reference
Reusable
Fitting
Socket Data
Page
189
65
ADAPTERS &
TUBE FITTINGS
FC469
PTFE
Conductive
r
Part Number
ACCESSORIES &
FC469-06
FC469-08
FC469-10
Hose I.D.
Hose O.D.
mm
in.
mm
7,6
9,9
12,4
0.30
0.39
0.49
12,2
15,5
18,3
Construction
Conductive extruded PTFE tube
with stainless steel single wire
braid.
HOSE ASSEMBLY
EQUIPMENT
–54°C to +204°C [–65°F to +400°F]
in.
0.48
0.61
0.72
Maximum
Operating
Pressure
bar
psi
280,0 4000
280,0 4000
245,0 3500
Application
High pressure chemical and fluid
transfer. For information on specific fluid applications and high
400-404.
Engineering information is available for specific critical temperature requirements.
Contact Eaton.
Minimum
Burst
Pressure
bar
psi
mm
1120,0 16000
1120,0 16000
980,0 14000
63,5
73,2
82,6
in.
2.50
2.88
3.25
‡Use of an internal support coil in
-06 and larger PTFE hose is recommended for tube support
where extended or continuous
service at high temperature
together with low or negative
See pages 397-398.
APPENDICIES
30
Minimum
Bend
Radius
Vacuum
Service
Weight
of Hose
kPa
in/Hg
Kg/m
94,8‡
94,8‡
94,8‡
28‡
28‡
28‡
0,25
0,36
0,43
lbs/ft
0.17
0.24
0.29
Contact Eaton for fitting information.
SPECIALTY &
TRUCK HOSE
FC363
Convoluted PTFE
Nonconductive tube
r
in
mm
in
bar
psi
0.54
0.63
0.81
1.00
1.24
1.52
2.00
18,8
22,4
26,9
32,5
38,9
46,0
58,7
0.74
0.88
1.06
1.28
1.53
1.81
2.31
87,0
69,0
76,0
70,0
70,0
52,0
35,0
1250†
1000†
1100†
1000†
1000†
750†
500†
Construction
Convoluted PTFE tube with
stainless steel single wire braid
cover.
–54°C to +204°C [–65°F to +400°F]
Application
Chemical, food, water and waste
handling, and various transfer
applications. Not recommended
for steam-cold water cycling or
air. For more information on
pages 349-355.
bar
350,0
248,0
303,0
280,0
280,0
210,0
140,0
psi
5000
3600
4400
4000
4000
3000
2000
mm
in
73,2 2.88
76,2 3.00
95,3 3.75
127,0 5.00
158,8 6.25
190,5 7.50
254,0 10.00
Engineering information is
available for specific critical
temperature requirements.
Contact Eaton.
See pages 346-348.
Minimum
Kink
Radius
mm
25,4
38,1
50,8
63,5
88,9
114,3
152,4
Vacuum
Service
in
kPa
in/Hg
1.00
1.50
2.00
2.50
3.50
4.50
6.00
94,8
94,8
94,8
81,3
67,7
40,6
16,9
28
28
28
24
20
12
5
Fitting Reference
Crimp
Fitting
Socket Data
OTC*
LOW & MEDIUM
PRESSURE HOSE
13,7
16,0
20,6
25,4
31,5
38,6
50,8
Minimum
Bend
Radius
HIGH PRESSURE HOSE
mm
FC363-08
FC363-10
FC363-12
FC363-16
FC363-20
FC363-24
FC363-32
Hose O.D.
Hose I.D.
Minimum
Burst
Pressure
Page
131
64
66
* Applications under 250 psi (sizes -10
thru -24) not recommended for air applications.
HOSE FITTINGS
Part Number
Maximum
Operating
Pressure
FC364
Convoluted PTFE
ADAPTERS &
TUBE FITTINGS
Conductive tube
r
13,7
16,0
20,6
25,4
31,5
38,6
50,8
in
mm
in
bar
psi
bar
psi
0.54
0.63
0.81
1.00
1.24
1.52
2.00
18,8
22,4
26,9
32,3
38,9
46,0
58,7
0.74
0.88
1.06
1.27
1.53
1.81
2.31
87,0
69,0
76,0
70,0
70,0
52,0
35,0
1250†
1000†
1100†
1000†
1000†
750†
500†
350,0
248,0
303,0
280,0
280,0
210,0
140,0
5000
3600
4400
4000
4000
3000
2000
Construction
Convoluted conductive PTFE
tube with stainless steel wire
braid cover.
–54°C to +204°C [–65°F to +400°F]
Application
Steam lines and fuel transfer
applications where static
dissipation is required. Not
recommended for steam-cold
water cycling or air. For more
mm
in
73,2 2.88
76,2 3.00
95,3 3.75
127,0 5.00
158,8 6.25
190,5 7.50
254,0 10.00
Engineering information is
available for specific critical
temperature requirements.
Contact Eaton.
See pages 346-348.
Minimum
Kink
Radius
mm
25,4
38,1
50,8
63,5
88,9
114,3
152,4
Vacuum
Service
in
kPa
in/Hg
1.00
1.50
2.00
2.50
3.50
4.50
6.00
94,8
94,8
94,8
81,3
67,7
40,6
16,9
28
28
28
24
20
12
5
Fitting Reference
Crimp
Fitting
Socket Data
OTC*
ACCESSORIES &
mm
FC364-08
FC364-10
FC364-12
FC364-16
FC364-20
FC364-24
FC364-32
Hose O.D.
Minimum
Bend
Radius
Page
HOSE ASSEMBLY
EQUIPMENT
Hose I.D.
Minimum
Burst
Pressure
131
64
66
* Applications under 250 psi (sizes -10
thru -24) not recommended for air applications.
APPENDICIES
Part Number
Maximum
Operating
Pressure
31
SPECIALTY &
TRUCK HOSE
FC563
Convoluted PTFE
Nonconductive tube
LOW & MEDIUM
PRESSURE HOSE
r
Part Number
HIGH PRESSURE HOSE
FC563-08
FC563-12
FC563-16
FC563-20
FC563-24
FC563-32
Hose I.D.
Hose O.D.
Maximum
Operating
Pressure
Minimum
Burst
Pressure
Minimum
Bend
Radius
Vacuum
Service
mm
in
mm
in
bar
psi
bar
psi
mm
in
kPa
in/Hg
13,7
20,6
25,4
31,5
38,6
50,8
0.54
0.81
1.00
1.24
1.52
2.00
18,8
29,9
32,5
38,9
46,0
58,7
0.74
1.06
1.28
1.53
1.81
2.31
87,0
76,0
70,0
70,0
52,0
35,0
1250
1100
1000
1000
750
500
350,0
303,0
280,0
280,0
210,0
140,0
5000
4400
4000
4000
3000
2000
73,2
95,3
127,0
158,8
190,5
254,0
2.88
3.75
5.00
6.25
7.50
10.00
94,8
94,8
81,2
67,7
33,9
23,7
28
28
24
20
10
7
Construction
Convoluted PTFE tube with stainless steel single wire braid reinforcement and integral black polyester overbraid cover.
HOSE FITTINGS
–54°C to +150°C [–65°F to +300°F]
Application
Chemical transfer and various
chemical processing applications.
Not recommended for steam or
Fitting Reference
Crimp
Fitting
Socket Data
Page
131
64
Factory crimp only.
See pages 346-348.
ADAPTERS &
TUBE FITTINGS
2575
Low pressure SOCKETLESS™
Textile Braid
ACCESSORIES &
r
Part Number
HOSE ASSEMBLY
EQUIPMENT
2575-4
2575-6
2575-8
2575-10
2575-12
Hose I.D.
mm
in
6,4
9,7
12,7
16,0
19,1
0.25
0.38
0.50
0.63
0.75
Construction
Synthetic rubber tube, textile braid
reinforcement, black synthetic
rubber cover (only).
–40°C to +100°C [–40°F to +212°F]
APPENDICIES
Water not to exceed +66°C
[+150°F] and air not to exceed
+71°C [+160°F].
32
Hose O.D.
mm
11,9
15,8
19,1
23,1
26,2
Maximum
Operating
Pressure
Minimum
Burst
Pressure
Minimum
Bend
Radius
in
bar
psi
bar
psi
mm
0.47
0.62
0.75
0.91
1.03
17,0
17,0
17,0
14,0
14,0
250
250
250
200
200
70,0 1000
70,0 1000
70,0 1000
56,0 800
56,0 800
76,2
101,6
127,0
152,4
177,8
Application
For gasoline, fuel and lubricating
oils, air and water. Not recommended for hydraulic impulse
applications and not approved for
airbrake applications. For more
information on specific fluid applications and high temperature ratings, see pages 349-355.
in
Kg/m
lbs/ft
3.00
4.00
5.00
6.00
7.00
0,13
0,19
0,25
0,30
0,33
0.09
0.13
0.17
0.20
0.22
See pages 346-348.
Weight
of Hose
Fitting Reference
Reusable
Fitting
Page
176
SPECIALTY &
TRUCK HOSE
FC332 AQP
Textile Braid
r
mm
in
6,4
9,7
12,7
16,0
19,1
0.25
0.38
0.50
0.63
0.75
Construction
AQP elastomer tube, textile braid
reinforcement, AQP elastomer
cover.
–40°C to +150°C [–40°F to +302°F]
mm
12,4
16,0
19,1
23,1
26,4
in
bar
0.49
0.63
0.75
0.91
1.04
17,0
17,0
17,0
17,0
17,0
psi
250
250
250
250
250
Application
applications and high
349-355.
bar
psi
70,0
70,0
70,0
70,0
70,0
1000
1000
1000
1000
1000
mm
76,2
76,2
127,0
152,4
177,8
Vacuum
Service
in
kPa
3.00
3.00
5.00
6.00
7.00
94,8
94,8
94,8
60,9
60,9
See pages 346-348.
Weight
of Hose
in/Hg
Kg/m
lbs/ft
28
28
28
18
18
0,12
0,18
0,22
0,30
0,42
0.08
0.12
0.15
0.20
0.28
Fitting Reference
Reusable
Fitting
Page
176
HOSE FITTINGS
[+250°F] and water not to
exceed +82°C [+180°F].
Hose O.D.
Minimum
Bend
Radius
LOW & MEDIUM
PRESSURE HOSE
FC332-04
FC332-06
FC332-08
FC332-10
FC332-12
Hose I.D.
Minimum
Burst
Pressure
HIGH PRESSURE HOSE
Part Number
Maximum
Operating
Pressure
ADAPTERS &
TUBE FITTINGS
FC647
Textile braid
ACCESSORIES &
Fire resistant meets RMA/CGA flame test requirements
r
mm
in
6,4
9,7
12,7
16,0
19,1
0.25
0.38
0.50
0.63
0.75
Construction
braid reinforcement, polyester
braided cover.
–40°C to +100°C [–40°F to +212°F]
Water not to exceed +66°C
(+150°F),
air not to exceed +74°C (+165°F).
Hose O.D.
mm
13,2
16,8
20,1
23,4
26,7
in
bar
0.52
0.66
0.79
0.92
1.05
25,0
21,0
21,0
17,0
17,0
psi
360
300
300
250
250
Application
bar
psi
99,0
84,0
84,0
70, 0
70,0
1440
1200
1200
1000
1000
Minimum
Bend
Radius
mm
76,2
76,2
127,0
152,4
177,8
Vacuum
Service
in
kPa
3.00
3.00
5.00
6.00
7.00
94,8
94,8
94,8
60,9
60,9
*NOTE: You must insert the correct color code in the complete
part number. Color codes are
BLK = black, BLU = blue,
BRN = brown, GRN = green,
WHT = white.
Example: FC647-04GRN
is a green cover in dash size 4.
Not all sizes are available in
all colors.
Weight
of Hose
in/Hg
Kg/m
lbs/ft
28
28
28
18
18
0,09
0,15
0,18
0,24
0,27
0.06
0.09
0.12
0.16
0.18
Fitting Reference
Reusable
Fitting
HOSE ASSEMBLY
EQUIPMENT
FC647-04*
FC647-06*
FC647-08*
FC647-10*
FC647-12*
Hose I.D.
Minimum
Burst
Pressure
Page
176
APPENDICIES
Part Number
Maximum
Operating
Pressure
See pages 346-348.
33
SPECIALTY &
TRUCK HOSE
2556/2565
Textile braid
Meets performance requirements SAE 30R2 Type 1
r
LOW & MEDIUM
PRESSURE HOSE
Part Number
Hose I.D.
Hose O.D.
Minimum
Bend
Radius
Weight
of Hose
HIGH PRESSURE HOSE
in
in
bar
bar
psi
in
kPa
in/Hg
Kg/m
lbs/ft
6,4
9,7
12,7
16,0
19,1
0.25
0.38
0.50
0.63
0.75
12,4
15,7
19,1
23,1
26,2
0.49
0.62
0.75
0.91
1.03
25,0
21,0
21,0
17,0
17,0
360
300
300
250
250
99,0
84,0
84,0
70,0
70,0
1440
1200
1200
1000
1000
76,2
76,2
127,0
152,4
177,8
3.00
3.00
5.00
6.00
7.00
94,8
94,8
94,8
61,0
61,0
28
28
28
18
18
0,12
0,18
0,24
0,31
0,37
0.08
0.12
0.16
0.21
0.25
2565-4
2565-6
2565-8
2565-10
2565-12
6,4
9,7
12,7
16,0
19,1
0.25
0.38
0.50
0.63
0.75
12,7
16,0
19,8
24,6
27,7
0.50
0.63
0.78
0.97
1.09
21,0
17,0
14,0
12,0
8,5
300
250
200
175
125
87,0
70,0
52,0
49,0
35,0
1250
1000
750
700
500
57,2
76,2
95,3
120,7
139,7
2.25
3.00
3.75
4.75
5.50
67,7
67,7
33,9
33,9
33,9
20
20
10
10
10
0,13
0,16
0,25
0,42
0,45
0.09
0.11
0.17
0.28
0.30
HOSE FITTINGS
2556: -40°C to +100°C [-40°F to
+212°F]. Water not to exceed
+66°C [+150°F], air not to exceed
+160°C [+71°F].
2565: -54°C to +121°C [-65°F to
+250°F]. Water not to exceed
+66°C [+150°F], air not to exceed
+74°C [+165°F].
Application
mm
Vacuum
Service
mm
psi
Minimum
Burst
Pressure
2556-4
2556-6
2556-8
2556-10
2556-12
Construction
Synthetic rubber tube, textile braid
reinforcement, synthetic rubber
cover.
mm
Maximum
Operating
Pressure
See pages 346-348.
Fitting Reference
Reusable
Fitting
Page
176
2565 is a low-temperature synthetic rubber covered MIL-DTL13444 Type 1, Class A hose.
ADAPTERS &
TUBE FITTINGS
FC619
Flexible 1/2 SAE bend
Wire inserted suction
ACCESSORIES &
Exceeds SAE 100R4
r
Part Number
HOSE ASSEMBLY
EQUIPMENT
FC619-12
FC619-16
FC619-20
FC619-24
FC619-32
FC619-40
FC619-48
Hose I.D.
mm
in
19,1
25,4
31,8
38,1
50,8
63,5
76,2
0.75
1.00
1.25
1.50
2.00
2.50
3.00
APPENDICIES
Construction
Synthetic rubber tube, reinforcement consisting of a helical wire
between two textile reinforcement layers and synthetic rubber
cover.
–40°C to +135°C [–40°F to +275°F]
34
Hose O.D.
mm
30,7
37,6
44,5
51,8
64,8
79,2
95,3
Maximum
Operating
Pressure
in
bar
1.21
1.48
1.75
2.04
2.55
3.12
3.75
21,0
17,0
14,0
10,5
7,0
4,0
4,0
psi
300†
250†
200†
150†
100†
62
62
Application
Suction and transfer applications
for petroleum hydraulic fluids,
fuel, lubricating oils, gasoline,
water and many other industrial
fluids. For more information on
pages 349-355.
Minimum
Burst
Pressure
bar
psi
84,0
70,0
56,0
42,0
28,0
17,0
16,0
1200
1000
800
600
400
250
225
Minimum
Bend
Radius
mm
in
63,5 2.50
76,2 3.00
102,0 4.00
127,0 5.00
152,4 6.00
355,6 14.00
457,2 18.00
† Maximum working pressure for
band clamp type fittings is 3,4 bar
[50 psi].
NOTE: -40 and -48 sizes require
special tooling for crimp fittings.
Contact Eaton for information.
See pages 346-348.
Vacuum
Service
kPa
94,8
94,8
94,8
94,8
94,8
94,8
94,8
Weight
of Hose
in/Hg
Kg/m
lbs/ft
28
28
28
28
28
28
28
0,68
0,83
1,16
1,49
1,83
2,35
3,36
0.46
0.56
0.78
1.00
1.23
1.58
2.26
Fitting Reference
Crimp
OTC
TTC
-40, -48
Socket Data
Reusable
Nipple
Clamps
Page
66
66
133
64
66
184
SPECIALTY &
TRUCK HOSE
2661 AQP
Wire inserted suction
Exceeds SAE 100R4
r
19,1
25,4
31,8
38,1
50,8
63,5
76,2
101,6
in
0.75
1.00
1.25
1.50
2.00
2.50
3.00
4.00
Construction
AQP elastomer tube, reinforcement consisting of a helical wire
between two textile braids and
–40°C to +150°C [–40°F to +302°F]
mm
31,8
38,1
45,7
52,3
64,8
78,2
90,9
119,1
in
bar
1.25
1.50
1.80
2.06
2.55
3.08
3.58
4.69
21,0
17,0
14,0
10,5
7,0
4,0
4,0
3,5
psi
300†
250†
200†
150†
100†
62
62
50
Application
Suction and transfer applications
for petroleum and fire resistant
hydraulic fluids, fuel, lubricating
oils, gasoline, water and many
other industrial fluids. For more
bar
psi
84,0
70,0
56,0
42,0
28,0
16,0
16,0
14,0
1200
1000
800
600
400
225
225
200
mm
in
125,0
150,0
200,0
255,0
300,0
355,0
460,0
610,0
5.00
6.00
8.00
10.00
12.00
14.00
18.00
24.00
† Maximum working pressure for
band clamp type fittings is 3,4 bar
[50 psi].
‡Sold as bulk hose only.
See pages 346-348.
Vacuum
Service
kPa
94,8
94,8
94,8
94,8
94,8
94,8
94,8
94,8
Weight
of Hose
in/Hg
Kg/m
28
28
28
28
28
28
28
28
0,62
0,74
1,34
1,68
1,93
2,56
2,92
4,58
Fitting Reference
Crimp
OTC
TTC
-40, -48
Socket Data
Reusable
Nipple
Clamps
LOW & MEDIUM
PRESSURE HOSE
mm
2661-12
2661-16
2661-20
2661-24
2661-32
2661-40
2661-48‡
2661-64‡
Hose O.D.
Minimum
Bend
Radius
lbs/ft
0,42
0,50
0,90
1,13
1,30
1,72
1,96
3,08
HIGH PRESSURE HOSE
Hose I.D.
Minimum
Burst
Pressure
Page
66
66
133
64
HOSE FITTINGS
Part Number
Maximum
Operating
Pressure
66
184
ADAPTERS &
TUBE FITTINGS
FC466
Textile braid
Exceeds SAE 100R6 performance*
mm
in
6,4
9,7
12,7
16,0
19,1
0.25
0.38
0.50
0.63
0.75
Construction
braid reinforcement and polyester braid cover.
–40°C to +100°C [–40°F to +212°F],
Air not to exceed +71°C [+160°F].
Hose O.D.
mm
12,2
15,7
19,1
23,1
26,2
in
bar
0.48
0.62
0.75
0.91
1.03
28,0
28,0
28,0
24,0
24,0
psi
400
400
400
350
350
Application
For gasoline, fuel, lubricating oils,
air and water. Not approved for
bar
112,0
112,0
112,0
98,0
98,0
psi
1600
1600
1600
1400
1400
mm
63,5
75,0
100,0
125,0
150,0
Vacuum
Service
in
kPa
2.50
3.00
4.00
5.00
7.00
94,8
94,8
94,8
60,9
60,9
* All sizes except –12
See pages 346-348.
Weight
of Hose
in/Hg
Kg/m
lbs/ft
28
28
28
18
18
0,09
0,15
0,19
0,27
0,28
0.06
0.10
0.13
0.18
0.19
Fitting Reference
Crimp
OTC
Skive Nipple**
Socket Data
HOSE ASSEMBLY
EQUIPMENT
FC466-04
FC466-06
FC466-08
FC466-10
FC466-12
Hose I.D.
Minimum
Bend
Radius
Page
66
66
64
**No skiving required.
APPENDICIES
Part Number
Minimum
Burst
Pressure
ACCESSORIES &
r
Maximum
Operating
Pressure
35
SPECIALTY &
TRUCK HOSE
FC498 AQP
Textile braid
Exceeds SAE 100R6
r
LOW & MEDIUM
PRESSURE HOSE
Part Number
FC498-04
FC498-06
FC498-08
FC498-10
FC498-12
Hose I.D.
mm
in
6,4
9,7
12,7
16,0
19,1
0.25
0.38
0.50
0.63
0.75
HIGH PRESSURE HOSE
Construction
reinforcement, blue AQP elastomer cover.
–40°C to +150°C [–40°F to +302°F]
Hose O.D.
mm
12,7
15,7
19,1
23,1
26,2
Maximum
Operating
Pressure
in
bar
0.50
0.62
0.75
0.91
1.03
28,0
28,0
28,0
24,0
24,0
psi
400
400
400
350
350
Application
Low pressure return lines in
hydraulic systems. For more
Minimum
Burst
Pressure
bar
112,0
112,0
112,0
98,0
98,0
psi
1600
1600
1600
1400
1400
Minimum
Bend
Radius
mm
63,5
75,0
100,0
125,0
150,0
Vacuum
Service
in
kPa
2.50
3.00
4.00
5.00
6.00
94,8
94,8
94,8
60,9
60,9
See pages 346-348.
Weight
of Hose
in/Hg
Kg/m
lbs/ft
28
28
28
18
18
0,12
0,19
0,22
0,30
0,42
0.08
0.13
0.15
0.20
0.28
Fitting Reference
Crimp
OTC
Skive Nipple**
Socket Data
Page
66
66
64
HOSE FITTINGS
FC598 AQP
Textile braid
ADAPTERS &
TUBE FITTINGS
Exceeds SAE 100R6
r
Part Number
ACCESSORIES &
FC598-04
FC598-06
FC598-08
FC598-10
FC598-12
Hose I.D.
mm
in
6,4
9,7
12,7
16,0
19,1
0.25
0.38
0.50
0.63
0.75
HOSE ASSEMBLY
EQUIPMENT
Construction
reinforcement, black AQP elastomer cover.
–40°C to +150°C [–40°F to +302°F]
Hose O.D.
mm
12,2
15,7
19,1
23,1
26,2
Maximum
Operating
Pressure
in
bar
0.50
0.62
0.78
0.91
1.03
28,0
28,0
28,0
24,0
24,0
psi
400
400
400
350
350
Application
Low pressure return lines in
hydraulic systems. For more
Minimum
Burst
Pressure
bar
112,0
112,0
112,0
98,0
98,0
psi
1600
1600
1600
1400
1400
Minimum
Bend
Radius
mm
63,5
75,0
100,0
125,0
150,0
Vacuum
Service
in
kPa
2.50
3.00
4.00
5.00
6.00
94,8
94,8
94,8
60,9
60,9
See pages 346-348.
Weight
of Hose
in/Hg
Kg/m
lbs/ft
28
28
28
18
18
0,12
0,19
0,22
0,30
0,42
0.08
0.13
0.15
0.20
0.28
Fitting Reference
Crimp
OTC
Skive Nipple**
Socket Data
Page
APPENDICIES
36
66
66
64
SPECIALTY &
TRUCK HOSE
2580
Double textile braid
MIL-H-24136/3
r
in
4,8
6,4
7,9
10,4
12,7
16,0
22,4
28,5
45,7
46,0
0.19
0.25
0.31
0.41
0.50
0.63
0.88
1.12
1.38
1.81
Construction
textile braid reinforcement
and synthetic rubber cover.
For larger dash sizes, see
Catalog A-MM-MC-0001-E.
mm
13,2
14,7
17,3
19,6
23,4
27,4
31,5
38,1
44,5
56,4
in
bar
psi
0.52
0.58
0.68
0.77
0.92
1.08
1.24
1.50
1.75
2.22
70,0
56,0
45,0
43,0
42,0
38,0
35,0
31,0
28,0
24,0
1000
800
650
625
600
550
500
450
400
350
Application
For water, gasoline, and fuel oil.
temperature ratings, see
pages 349-355.
bar
psi
280,0
224,0
180,0
175,0
168,0
152,0
140,0
124,0
112,0
98,0
4000
3200
2600
2500
2400
2200
2000
1800
1600
1400
mm
76,2
85,9
101,6
117,3
139,7
165,1
187,5
228,6
266,7
336,6
Weight
of Hose
in
Kg/m
lbs/ft
3.00
3.38
4.00
4.62
5.50
6.50
7.38
9.00
10.50
13.25
0,18
0,22
0,25
0,28
0,42
0,51
0,54
0,64
0,76
1,12
0.12
0.15
0.17
0.19
0.28
0.34
0.36
0.43
0.51
0.75
See pages 346-348.
Fitting Reference
Reusable
Fitting
Socket Data
LOW & MEDIUM
PRESSURE HOSE
mm
Hose O.D.
Minimum
Bend
Radius
HIGH PRESSURE HOSE
2580-4
2580-5
2580-6
2580-8
2580-10
2580-12
2580-16
2580-20
2580-24
2580-32
Hose I.D.
Minimum
Burst
Pressure
Page
136
65
HOSE FITTINGS
Part Number
Maximum
Operating
Pressure
–40°C to +100°C [–40°F to +212°F].
ADAPTERS &
TUBE FITTINGS
2583
Double textile braid
SAE 100R3
mm
in
6,4
9,7
12,7
19,1
25,4
31,8
0.25
0.38
0.50
0.75
1.00
1.25
Construction
textile braid reinforcement and
–40°C to +100°C [–40°F to +212°F].
Air not to exceed +71°C [+161°F].
Hose O.D.
mm
14,5
19,1
23,9
31,8
38,1
44,5
in
bar
psi
bar
psi
mm
0.57
0.75
0.94
1.25
1.50
1.75
87,0
78,0
70,0
52,0
39,0
26,0
1250
1125
1000
750
565
375
350,0
315,0
280,0
210,0
157,0
105,0
5000
4500
4000
3000
2250
1500
76,2
101,6
127,0
152,4
203,2
254,0
Application
For hydraulics, fuel, lubricating
oils, gasoline, air and water. Not
approved for airbrake applications. For more information on
pages 349-355.
Weight
of Hose
in
Kg/m
lbs/ft
3.00
4.00
5.00
6.00
8.00
10.00
0,18
0,33
0,39
0,71
0,76
1,09
0.12
0.22
0.26
0.48
0.51
0.73
See pages 346-348.
Fitting Reference
Crimp
OTC
HOSE ASSEMBLY
EQUIPMENT
2583-4
2583-6
2583-8
2583-12
2583-16
2583-20
Hose I.D.
Minimum
Bend
Radius
Page
66
APPENDICIES
Part Number
Minimum
Burst
Pressure
ACCESSORIES &
r
Maximum
Operating
Pressure
37
SPECIALTY &
TRUCK HOSE
2681
HI-IMPULSE®
Single wire braid
Meets or exceeds:
SAE 100R1A, EN853 1ST, ISO 1436-1 Type 1ST
r
LOW & MEDIUM
PRESSURE HOSE
Part Number
HIGH PRESSURE HOSE
2681-3
2681-4
2681-5
2681-6
2681-8
2681-10
2681-12
2681-16
2681-20
2681-24
2681-32
Hose I.D.
mm
in
4,8
6,4
7,9
9,7
12,7
16,0
19,1
25,4
31,8
38,1
50,8
0.19
0.25
0.31
0.38
0.50
0.63
0.75
1.00
1.25
1.50
2.00
HOSE FITTINGS
Construction
wire braid reinforcement and
–40°C to +100°C [–40°F to +212°F]
Hose O.D.
mm
12,7
15,8
17,5
19,8
23,1
26,2
30,2
38,1
46,0
52,3
65,5
in
0.50
0.62
0.69
0.78
0.91
1.03
1.19
1.50
1.81
2.06
2.58
Maximum
Operating
Pressure
bar
psi
280,0
227,0
227,0
210,0
175,0
140,0
124,0
90,0
60,0
49,0
42,0
4000
3250
3250
3000
2500
2000
1800
1300
900
700
600
Application
Hydraulic system service with
petroleum and water-base fluids,
for general industrial service. For
Minimum
Burst
Pressure
bar
psi
1120,0
897,0
897,0
840,0
700,0
560,0
497,0
359,0
248,0
193,0
168,0
16000
13000
13000
12000
10000
8000
7200
5200
3600
2800
2400
mm
88,9
100,0
115,0
125,0
180,0
200,0
240,0
300,0
420,0
500,0
630,0
ACCESSORIES &
HOSE ASSEMBLY
EQUIPMENT
APPENDICIES
Weight
of Hose
in
Kg/m
lbs/ft
3.50
4.00
4.50
5.00
7.00
8.00
9.50
12.00
16.50
20.00
25.00
0,19
0,28
0,40
0,45
0,58
0,68
0,79
1,19
1,46
1,67
2,43
0.13
0.19
0.27
0.30
0.39
0.46
0.53
0.80
0.98
1.12
1.63
See pages 346-348.
ADAPTERS &
TUBE FITTINGS
38
Minimum
Bend
Radius
Fitting Reference
Crimp
Skive Nipple
Socket Data
Page
66
64
SPECIALTY &
TRUCK HOSE
GH663
MATCHMATE Plus
HI-IMPULSE
Single wire braid
LOW & MEDIUM
PRESSURE HOSE
Meets or exceeds:
SAE 100R1AT Type S, EN853 1SN, ISO 1436-1 Type 1SN
r
Hose O.D.
mm
mm
in
in
GH663-4
6,4
0.25
13,5
0.53
GH663-6
9,7
0.38
17,5
0.69
GH663-8
12,7
0.50
20,6
0.81
GH663-12
19,1
0.75
27,7
1.09
GH663-16
GH663-20
GH663-24
GH663-32
25,4
31,8
38,1
50,8
1.00
1.25
1.50
2.00
35,8
43,4
50,6
64,0
1.41
1.71
1.99
2.52
–40°C to +100°C [–40°F to +212°F]
psi
bar
psi
3250†
2750
3000†
2250
2500†
2000
1800†
1250
1300†
1000
950
725
580
897,0
770,0
840,0
630,0
700,0
560,0
497,0
350,0
359,0
280,0
260,0
200,0
160,0
13000†
11000
12000†
9000
10000†
8000
7200†
5000
5200†
4000
3770
2900
2320
Application
mm
Weight
of Hose
in
Kg/m
lbs/ft
100,0
4.00
0,24
0.16
125,0
5.00
0,37
0.25
180,0
7.00
0,45
0.30
241,3
9.50
0,67
0.45
304,8
419,1
508,0
635,0
12.00
16.50
20.00
25.00
1,01
1,31
1,56
1,95
0.68
0.88
1.05
1.31
† Improved performance when used
with Global Crimp fittings.
See pages 346-348.
Fitting Reference
Crimp
TTC
Skive Nipple
Socket Data
Reusable
Fitting
Socket Data
Page
66
66
64
148
65
ADAPTERS &
TUBE FITTINGS
Construction
bar
227,0
192,0
210,0
157,0
175,0
140,0
124,0
87,0
90,0
70,0
66,0
50,0
40,0
Minimum
Bend
Radius
HIGH PRESSURE HOSE
Hose I.D.
Minimum
Burst
Pressure
HOSE FITTINGS
Part Number
Maximum
Operating
Pressure
ACCESSORIES &
GH194 AQP
MATCHMATE BLUE
HI-IMPULSE
Single wire braid
Meets or exceeds:
r
mm
in
6,4
9,7
12,7
16,0
19,1
25,4
31,8
0.25
0.38
0.50
0.63
0.75
1.00
1.25
Construction
braid reinforcement and blue
AQP elastomer cover.
–40°C to +150°C [–40°F to +300°F].
Hose O.D.
mm
13,5
17,5
20,6
23,9
27,7
35,8
43,9
in
0.53
0.69
0.81
0.94
1.09
1.41
1.73
bar
psi
227,0
210,0
175,0
140,0
124,0
90,0
62,0
3250
3000
2500
2000
1800
1300
900
Application
Petroleum and fire-resistant
hydraulic fluids, fuel and lubricating oils, gasoline, water and
other industrial fluids. For more
bar
Minimum
Bend
Radius
psi
mm
897,0 13000
840,0 12000
700,0 10000
560,0 8000
497,0 7200
359,0 5200
248,0 3600
100,0
125,0
180,0
205,0
240,0
300,0
420,0
Weight
of Hose
in
Kg/m
lbs/ft
4.00
5.00
7.00
8.00
9.50
12.00
16.50
0,25
0,37
0,45
0,54
0,68
0,98
1,26
0.17
0.25
0.30
0.36
0.46
0.66
0.85
See pages 346-348.
Fitting Reference
Crimp
TTC
Skive Nipple
Socket Data
HOSE ASSEMBLY
EQUIPMENT
GH194-4
GH194-6
GH194-8
GH194-10
GH194-12
GH194-16
GH194-20
Hose I.D.
Minimum
Burst
Pressure
Page
APPENDICIES
Part Number
Maximum
Operating
Pressure
66
66
64
39
SPECIALTY &
TRUCK HOSE
FC194 AQP
HI-IMPULSE
Single wire braid
Meets or exceeds:
r
LOW & MEDIUM
PRESSURE HOSE
Part Number
HIGH PRESSURE HOSE
FC194-04
FC194-06
FC194-08
FC194-10
FC194-12
FC194-16
FC194-20
Hose I.D.
mm
in
6,4
9,7
12,7
16,0
19,1
25,4
31,8
0.25
0.38
0.50
0.63
0.75
1.00
1.25
Construction
braid reinforcement and blue
–40°C to +150°C [–40°F to +302°F]
Hose O.D.
mm
16,0
19,8
22,9
26,2
30,2
38,1
46,0
Maximum
Operating
Pressure
in
bar
psi
0.63
0.78
0.90
1.03
1.19
1.50
1.81
227,0
210,0
175,0
140,0
124,0
90,0
62,0
3250
3000
2500
2000
1800
1300
900
HOSE FITTINGS
Application
hydraulic fluids, fuel, lubricating
oils, gasoline, water, and other
industrial fluids. For more information on specific fluid applications and high temperature ratings, see pages 349-355.
Minimum
Burst
Pressure
bar
Minimum
Bend
Radius
psi
mm
897,0 13000
840,0 12000
700,0 10000
560,0 8000
497,0 7200
359,0 5200
248,0 3600
100,0
125,0
180,0
200,0
240,0
300,0
420,0
Weight
of Hose
in
Kg/m
lbs/ft
4.00
5.00
7.00
8.00
9.50
12.00
16.50
0,28
0,45
0,58
0,68
0,79
1,19
1,46
0.19
0.30
0.39
0.46
0.53
0.80
0.98
See pages 346-348.
Fitting Reference
Crimp
Skive Nipple
Socket Data
Page
66
64
ADAPTERS &
TUBE FITTINGS
FC611
EPDM hose
Single wire braid
ACCESSORIES &
r
Part Number
HOSE ASSEMBLY
EQUIPMENT
FC611-04
FC611-06
FC611-08
FC611-12
FC611-16
FC611-20
FC611-24
FC611-32
Hose I.D.
mm
in
6,4
9,7
12,7
19,1
25,4
31,8
38,1
50,8
0.25
0.38
0.50
0.75
1.00
1.25
1.50
2.00
Construction
Synthetic EPDM tube, single
green EPDM synthetic cover.
–40°C to +75°C [–40°F to +175°F]
APPENDICIES
40
Hose O.D.
mm
13,5
17,3
20,3
27,9
35,8
43,4
50,5
64,0
in
0.53
0.68
0.80
1.10
1.41
1.71
1.99
2.52
Maximum
Operating
Pressure
bar
psi
210,0
157,0
140,0
87,0
70,0
43,0
35,0
26,0
3000
2250
2000
1250
1000
625
500
375
Application
Ground support equipment
(GSE), industrial phosphate esterbased fluids, water glycol systems. For more information on
pages 349-355.
Minimum
Burst
Pressure
bar
Minimum
Bend
Radius
psi
mm
840,0 12000
630,0 9000
560,0 8000
350,0 5000
280,0 4000
175,0 2500
140,0 2000
105,0 1500
101,6
127,0
177,8
241,3
304,8
419,1
508,0
635,0
in
Kg/m
lbs/ft
4.00
5.00
7.00
9.50
12.00
16.50
20.00
25.00
0,24
0,33
0,42
0,64
0,89
1,19
1,52
1,90
0.16
0.22
0.28
0.43
0.60
0.80
1.02
1.28
See pages 346-348.
Weight
of Hose
Fitting Reference
Crimp
TTC
Page
66
SPECIALTY &
TRUCK HOSE
FC310
Hi-Pac wire braid
Hose O.D.
mm
mm
bar
in
in
psi
bar
psi
FC310-04
6,4
0.25
14,0
0.55
350,0
5000.00
1400,0
20000
FC310-06
9,7
0.38
17,3
0.68
280,0
4000.00
1120,0
16000
FC310-08
12,7
0.50
20,1
0.79
245,0
3500.00
980,0
14000
FC310-10
16,0
0.63
23,6
0.93
192,0
2750.00
770,0
11000
FC310-12
19,1
0.75
27,4
1.08
157,0
2250.00
630,0
9000
FC310-16
25,4
1.00
34,6
1.36
140,0
2000.00
560,0
8000
FC310-20
31,8
1.25
42,9
1.69
113,0
1625.00
455,0
6500
–40°C to +100°C [–40°F to +212°F]
Application
more specific information on fluid
applications, see pages 349-355.
in
2.00†
3.00
2.50†
3.50
3.50†
5.00
4.00†
6.00
4.75†
7.00
6.00†
9.00
8.25†
11.00
† Improved minimum bend radius
when used with global fittings.
See pages 346-348.
Kg/m
lbs/ft
0,31
0.21
0,40
0.27
0,51
0.34
0,65
0.44
0,74
0.50
1,06
0.71
1,58
1.06
Fitting Reference
Crimp
TTC
Skive Nipple
Socket Data
Reusable
Fitting
Socket Data
Page
66
66
64
151
65
ADAPTERS &
TUBE FITTINGS
Construction
Synthetic rubber tube, HI-PAC
braided wire reinforcement, synthetic rubber cover.
mm
50,8
76,2
63,5
88,9
88,9
127,0
101,6
152,4
120,7
177,8
152,4
228,6
209,6
279,4
Weight
of Hose
HIGH PRESSURE HOSE
Hose I.D.
Minimum
Bend
Radius
HOSE FITTINGS
Part Number
Minimum
Burst
Pressure
LOW & MEDIUM
PRESSURE HOSE
r
Maximum
Operating
Pressure
ACCESSORIES &
FC510 AQP
Hi-Pac wire braid
r
mm
in
6,4
9,7
12,7
16,0
19,1
25,4
31,8
0.25
0.38
0.50
0.63
0.75
1.00
1.25
Construction
AQP elastomer tube, Hi-Pac
braided wire reinforcement and
–40°C to +150°C [–40°F to +302°F]
Hose O.D.
mm
14,5
17,5
20,3
23,6
27,7
34,8
43,2
in
bar
psi
bar
0.57
0.69
0.80
0.93
1.09
1.37
1.70
350,0
280,0
245,0
192,0
157,0
140,0
113,0
5000
4000
3500
2750
2250
2000
1625
1400,0
1120,0
980,0
770,0
630,0
560,0
455,0
Application
hydraulic fluids, fuel, and lubricating systems. For more information on specific fluid applications
see pages 346-348.
psi
20000
16000
14000
11000
9000
8000
6500
Minimum
Bend
Radius
mm
76,2
88,9
127,0
152,4
177,8
228,6
279,4
Weight
of Hose
in
Kg/m
lbs/ft
3.00
3.50
5.00
6.00
7.00
9.00
11.00
0,34
0,43
0,51
0,65
0,77
1,06
1,61
0.23
0.29
0.34
0.44
0.52
0.71
1.08
See pages 346-348.
Fitting Reference
Crimp
TTC
Skive Nipple
Socket Data
Reusable
Fitting
Socket Data
HOSE ASSEMBLY
EQUIPMENT
FC510-04
FC510-06
FC510-08
FC510-10
FC510-12
FC510-16
FC510-20
Hose I.D.
Minimum
Burst
Pressure
Page
66
66
64
APPENDICIES
Part Number
Maximum
Operating
Pressure
151
65
41
SPECIALTY &
TRUCK HOSE
FC639
Flexible cover
3000 PSI Constant pressure
SAE 100R17
LOW & MEDIUM
PRESSURE HOSE
r
Part Number
HIGH PRESSURE HOSE
FC639-04
FC639-06
FC639-08
FC639-10**
FC639-12**
FC639-16**
Hose I.D.
mm
in
6,4
9,7
12,7
16,0
19,1
25,4
0.25
0.38
0.50
0.63
0.75
1.00
Construction
Synthetic rubber tube with one
or two wire braid reinforcements, ozone flexible neoprene
rubber cover.
–40°C to +100°C [–40°F to +212°F]
Hose O.D.
mm
13,2
17,0
20,6
25,4
29,0
36,3
in
0.52
0.67
0.81
1.00
1.14
1.43
Maximum
Operating
Pressure
bar
psi
210,0
210,0
210,0
210,0
210,0
210,0
3000
3000
3000
3000
3000
3000
HOSE FITTINGS
Application
General industrial and hydraulic
system service with petroleum
and water-base fluids.
Recommended for high-pressure
oil lines used on construction
equipment and other off-highway
applications. For more information on specific fluid applications
see pages 349-355.
Minimum
Burst
Pressure
bar
psi
840,0
840,0
840,0
840,0
840,0
840,0
12000
12000
12000
12000
12000
12000
Minimum
Bend
Radius
mm
50,8
63,5
88,9
101,6
120,7
152,4
Weight
of Hose
in
Kg/m
lbs/ft
2.00
2.50
3.50
4.00
4.75
6.00
0,22
0,34
0,48
0,76
0,94
1,24
0.15
0.23
0.32
0.51
0.63
0.83
See pages 346-348.
**Two braids of high tensile wire.
Fitting Reference
Crimp
TTC
Skive Nipple
Socket Data
Page
66
66
64
ADAPTERS &
TUBE FITTINGS
GH681
Single wire braid
ACCESSORIES &
Exceeds EN 853 Type 1
r
Part Number
HOSE ASSEMBLY
EQUIPMENT
GH681-4
GH681-6
GH681-8
Hose I.D.
mm
in
6,4
9,7
12,7
0.25
0.38
0.50
Construction
synthetic rubber cover. Meets or
exceeds EN requirements at 1/2
SAE Bend Radius.
–40°C to +100°C [–40°F to +212°F]
Hose O.D.
mm
11,9
16,0
19,8
Maximum
Operating
Pressure
in
bar
psi
0.47
0.63
0.78
225,0
210,0
210,0
3250
3000
3000
Application
Minimum
Burst
Pressure
bar
psi
900,0 13050
840,0 12000
840,0 12000
Weight
of Hose
mm
in
Kg/m
lbs/ft
50,8
63,5
88,9
2.00
2.50
3.50
0,16
0,28
0,39
0.11
0.18
0.26
See pages 346-348.
APPENDICIES
42
Minimum
Bend
Radius
Fitting Reference
Crimp
TTC (-6 only)
Skive Nipple
Socket Data
Page
66
66
64
SPECIALTY &
TRUCK HOSE
FC839B BRUISER
Ultra-abrasion resistant cover
SAE 100R17
in
6,4
9,7
12,7
16,0
19,1
25,4
0.25
0.38
0.50
0.63
0.75
1.00
Construction
Synthetic rubber tube with one
or two layers of braided wire
reinforcement, synthetic rubber
intermediate cover and BRUISER
outer cover.
–40°C to +100°C [–40°F to +212°F]
mm
13,2
17,0
20,6
25,4
29,0
36,3
in
bar
psi
0.52
0.67
0.81
1.00
1.14
1.43
210,0
210,0
210,0
210,0
210,0
210,0
3000
3000
3000
3000
3000
3000
Application
High abrasion industrial and
hydraulic system applications
with petroleum and water-based
fluids. Recommended for use on
critcal applications in construction, forestry, and other off-highway vehicles. BRUISER outer
cover offers unmatched abrasion,
chemical, and environmental protection. For more information on
349-355.
bar
psi
840,0
840,0
840,0
840,0
840,0
840,0
12000
12000
12000
12000
12000
12000
mm
50,8
63,5
88,9
101,6
120,7
152,4
Weight
of Hose
in
Kg/m
lbs/ft
2.00
2.50
3.50
4.00
4.75
6.00
0,22
0,34
0,48
0,76
0,94
1,24
0.15
0.23
0.32
0.51
0.63
0.83
See pages 346-348.
**Two braids of high tensile wire.
Fitting Reference
Crimp
TTC
Skive Nipple
Socket Data
HIGH PRESSURE HOSE
mm
Hose O.D.
Page
66
66
64
HOSE FITTINGS
FC839B-04
FC839B-06
FC839B-08
FC839B-10**
FC839B-12**
FC839B-16**
Hose I.D.
Minimum
Bend
Radius
ADAPTERS &
TUBE FITTINGS
Part Number
Minimum
Burst
Pressure
LOW & MEDIUM
PRESSURE HOSE
r
Maximum
Operating
Pressure
ACCESSORIES &
FC849
r
mm
in
6,4
9,7
12,7
16,0
19,1
0.25
0.38
0.50
0.63
0.75
Construction
Synthetic rubber tube with two
layers of wire braid reinforcement and abrasion resistance
–40°C to +100°C [–40°F to +212°F]
Hose O.D.
mm
15,2
19,3
22,6
25,7
30,0
in
bar
psi
0.60
0.76
0.89
1.01
1.18
280,0
280,0
280,0
280,0
280,0
4000
4000
4000
4000
4000
Application
Industrial and hydraulic system
applications with petroleum and
water-based fluids. Recommended
for use on construction, forestry,
and other off-highway vehicles.
fluid applications and temperature ratings, see pages 349-355.
bar
psi
1120,0
1120,0
1120,0
1120,0
1120,0
16000
16000
16000
16000
16000
Minimum
Bend
Radius
mm
50,8
63,5
88,9
101,6
120,7
Weight
of Hose
in
Kg/m
lbs/ft
2.00
2.50
3.50
4.00
4.75
0,36
0,54
0,64
0,90
1,07
0.24
0.36
0.43
0.60
0.72
See pages 346-348.
Fitting Reference
Crimp
TTC
Skive Nipple *
Socket Data
HOSE ASSEMBLY
EQUIPMENT
FC849-04
FC849-06
FC849-08
FC849-10
FC849-12
Hose I.D.
Minimum
Burst
Pressure
Page
66
66
64
*-06 thru -12 only
APPENDICIES
Part Number
Maximum
Operating
Pressure
43
SPECIALTY &
TRUCK HOSE
FC849B BRUISER
4000 PSI Constant Pressure
r
LOW & MEDIUM
PRESSURE HOSE
Part Number
FC849B-04
FC849B-06
FC849B-08
FC849B-10
FC849B-12
Hose I.D.
mm
in
6,4
9,7
12,7
16,0
19,1
0.25
0.38
0.50
0.63
0.75
HIGH PRESSURE HOSE
Construction
Synthetic rubber tube with two
layers of wire braid reinforcement, synthetic rubber intermediate cover and BRUISER outer
cover.
–40°C to +100°C [–40°F to +212°F]
Hose O.D.
mm
15,2
19,3
22,6
25,7
30,0
Maximum
Operating
Pressure
in
bar
psi
0.60
0.76
0.89
1.01
1.18
280,0
280,0
280,0
280,0
280,0
4000
4000
4000
4000
4000
HOSE FITTINGS
Application
critcal applications in construction, forestry, and other off-highway vehicles. BRUISER outer
349-355.
Minimum
Burst
Pressure
bar
psi
mm
1120,0
1120,0
1120,0
1120,0
1120,0
16000
16000
16000
16000
16000
50,8
63,5
88,9
101,6
120,7
ACCESSORIES &
HOSE ASSEMBLY
EQUIPMENT
APPENDICIES
Weight
of Hose
in
Kg/m
lbs/ft
2.00
2.50
3.50
4.00
4.75
0,36
0,54
0,64
0,90
1,07
0.24
0.36
0.43
0.60
0.72
See pages 346-348.
ADAPTERS &
TUBE FITTINGS
44
Minimum
Bend
Radius
Fitting Reference
Crimp
TTC
Skive Nipple*
Socket Data
*-06 thru -12 only
Page
66
66
64
SPECIALTY &
TRUCK HOSE
GH120
MATCHMATE ICE
Cold temperature applications
in
6,4
9,7
12,7
16,0
19,1
25,4
31,8
38,1
50,8
0.25
0.38
0.50
0.63
0.75
1.00
1.25
1.50
2.00
Construction
Aeroquip brand exclusive low
temperature compound tube and
cover, double wire braid reinforcement.
–57°C to +100°C [–70°F to +212°F]
mm
14,2
17,3
20,8
24,9
28,4
35,8
43,4
51,6
63,8
Weight
of Hose
in
bar
psi
bar
psi
mm
in
Kg/m
lbs/ft
0.56
0.68
0.82
0.98
1.12
1.41
1.71
2.03
2.51
350,0
280,0
245,0
192,0
157,0
140,0
113,0
87,0
78,0
5000
4000
3500
2750
2250
2000
1625
1250
1125
1400,0
1120,0
980,0
770,0
630,0
560,0
455,0
350,0
315,0
20000
16000
14000
11000
9000
8000
6500
5000
4500
50,8
63,5
88,9
101,6
120,7
152,4
209,6
254,0
317,5
2.00
2.50
3.50
4.00
4.75
6.00
8.25
10.00
12.50
0,30
0,40
0,58
0,74
0,92
1,22
1,60
2,11
2,80
0.20
0.27
0.39
0.50
0.62
0.82
1.07
1.42
1.88
Application
Low temperature flexing and
hydraulic system service with
petroleum and water-base fluids.
For use in frigid environments on
construction equipment and other
mobile applications. For more
See pages 346-348.
Fitting Reference
Crimp
TTC
Skive Nipple *
Socket Data
HIGH PRESSURE HOSE
mm
Hose O.D.
Page
66
66
64
HOSE FITTINGS
GH120-4
GH120-6
GH120-8
GH120-10
GH120-12
GH120-16
GH120-20
GH120-24
GH120-32
Hose I.D.
Minimum
Bend
Radius
*-04 thru -20 only
ADAPTERS &
TUBE FITTINGS
Part Number
Minimum
Burst
Pressure
LOW & MEDIUM
PRESSURE HOSE
r
Maximum
Operating
Pressure
2766
Double wire braid
ACCESSORIES &
MIL-DTL-13531, Type II, Class A
r
Hose O.D.
mm
in.
mm
in.
bar
psi
6,4
9,7
12,7
19,1
25,4
31,8
38,1
50,8
0.25
0.38
0.50
0.75
1.00
1.25
1.50
2.00
17,5
21,3
24,6
31,8
39,6
50,8
57,2
69,9
0.69
0.84
0.97
1.25
1.56
2.00
2.25
2.75
350,0
280,0
245,0
157,0
140,0
113,0
87,0
78,0
5000
4000
3500
2250
2000
1625
1250
1000
Construction
–54°C to +93°C [–65°F to +200°F]
Application
High pressure hydraulics, fuel
and lubricating oil and gasoline.
For more information specific
temperature ratings, see
pages 349-355.
bar
psi
1400,0 20000
1120,0 16000
980,0 14000
630,0 9000
560,0 8000
455,0 6500
350,0 5000
315,0 4500
Minimum
Bend
Radius
mm
101,6
127,0
177,8
241,3
279,4
406,4
508,0
558,8
Weight
of Hose
in.
Kg/m
lbs/ft
4.00
5.00
7.00
9.50
11.00
16.00
20.00
22.00
0,47
0,68
0,80
1,11
1,51
2,41
2,42
3,97
0.32
0.46
0.54
0.75
1.02
1.63
1.64
2.69
See pages 346-348.
Fitting Reference
Crimp
Skive Nipple
Socket Data
Reusable
Fitting
Socket Data
HOSE ASSEMBLY
EQUIPMENT
2766-4
2766-6
2766-8
2766-12
2766-16
2766-20
2766-24
2766-32
Hose I.D.
Minimum
Burst
Pressure
Page
66
64
APPENDICIES
Part Number
Maximum
Operating
Pressure
156
65
45
SPECIALTY &
TRUCK HOSE
FC693
EPDM hose
Double wire braided high pressure
r
LOW & MEDIUM
PRESSURE HOSE
Part Number
FC693-04
FC693-06
FC693-08
Hose I.D.
mm
in
6,4
9,7
12,7
0.25
0.38
0.50
HIGH PRESSURE HOSE
Construction
Synthetic EPDM tube, double
green EPDM synthetic cover.
–40°C to +75°C [–40°F to +175°F]
Maximum
Operating
Pressure
Hose O.D.
mm
15,2
19,1
22,1
in
bar
psi
0.60
0.75
0.87
350,0
280,0
245,0
5000
4000
3500
Application
(GSE), industrial phosphate esterbased fluids, water glycol systems. For more information on
pages 349-355.
Minimum
Burst
Pressure
bar
psi
1400,0
1120,0
980,0
20000
16000
14000
Minimum
Bend
Radius
mm
101,6
127,0
177,8
Weight
of Hose
in
Kg/m
lbs/ft
4.00
5.00
7.00
0,37
0,54
0,60
0.25
0.36
0.40
See pages 346-348.
Fitting Reference
Crimp
TTC
Page
66
HOSE FITTINGS
FC735 BRUISER
Hi-Impulse Double wire braid
ADAPTERS &
TUBE FITTINGS
Meets or exceeds:
SAE 100R16 Type S, EN 857 2SC, ISO 11237-1 Type 2SC
r
Part Number
ACCESSORIES &
FC735-04*
FC735-06
FC735-08
FC735-10
FC735-12
FC735-16
FC735-20
Hose I.D.
mm
in
6,4
9,7
12,7
16,0
19,1
25,4
31,8
0.25
0.38
0.50
0.63
0.75
1.00
1.25
HOSE ASSEMBLY
EQUIPMENT
Construction
wire braid reinforcement, synthetic rubber intermediate cover,
and BRUISER outer cover. Meets
or exceeds EN requirements at
1/2 SAE bend radius.
–40°C to +100°C [–40°F to +212°F]
Hose O.D.
mm
13,5
17,5
20,6
23,6
27,9
36,1
43,2
Maximum
Operating
Pressure
Minimum
Burst
Pressure
in
bar
psi
bar
psi
0.53
0.69
0.81
0.93
1.10
1.42
1.70
350,0
350,0
297,0
250,0
216,0
175,0
157,0
5000*
5000
4250
3625
3125
2500
2250
1400,0
1400,0
1190,0
1000,0
870,0
700,0
630,0
20000*
20000
17000
14500
12500
10000
9000
Application
High abrasion applications.
mm
50,8
63,5
88,9
101,6
120,7
152,4
209,6
in
Kg/m
lbs/ft
0,33
0,43
0,58
0,65
0,79
1,07
1,62
0.22
0.29
0.39
0.44
0.53
0.72
1.09
See pages 346-348.
Weight
of Hose
2.00
2.50
3.50
4.00
4.75
6.00
8.25
*Meets SAE100R2 pressures.
APPENDICIES
46
Minimum
Bend
Radius
Fitting Reference
Crimp
TTC
Skive Nipple
Socket Data
Page
66
66
64
SPECIALTY &
TRUCK HOSE
2781
HI-IMPULSE
Double wire braid
Meets or exceeds:
r
mm
in
in
2781-4
6,4
0.25
17,5
0.69
2781-6
9,7
0.38
21,3
0.84
2781-8
12,7
0.50
24,6
0.97
2781-10
16,0
0.63
27,7
1.09
2781-12
19,1
0.75
31,8
1.25
2781-16
25,4
1.00
39,6
1.56
2781-20
31,8
1.25
50,8
2.00
2781-24
38,1
1.50
57,2
2.25
2781-32
50,8
2.00
69,9
2.75
Construction
–40°C to +100°C [–40°F to +212°F]
bar
400,0
350,0
350,0
280,0
297,0
245,0
250,0
227,0
216,0
210,0
175,0
140,0
157,0
113,0
124,0
122,0
105,0
87,0
psi
5800†
5000
5000†
4000
4250†
3500
3625†
3250
3125†
3000
2500†
2000
2250†
1625
1800†
1750
1500†
1250
Application
bar
1600,0
1400
1400,0
1120,0
1190,0
980,0
1000,0
770,0
870,0
630,0
700,0
560,0
630,0
455,0
497,0
350,0
420,0
315,0
psi
23200†
20000
20000†
16000
17000†
14000
14500†
11000
12500†
9000
10000†
8000
9000†
6500
7200†
5000
6000†
4500
mm
in
Kg/m
lbs/ft
101,6
4.00
0,50
0.33
127,0
5.00
0,67
0.45
177,8
7.00
0,83
0.56
203,2
8.00
0,97
0.62
241,3
9.50
1,19
0.80
304,8
12.00
1,58
1.06
419,1
16.50
2,57
1.73
508,0
20.00
3,05
2.05
635,0
25.00
4,02
2.70
See pages 346-348.
†Improved pressure performance
Fitting Reference
Crimp
Skive Nipple
Socket Data
Reusable
Fitting
Socket Data
LOW & MEDIUM
PRESSURE HOSE
mm
Weight
of Hose
HIGH PRESSURE HOSE
Hose O.D.
Minimum
Bend
Radius
HOSE FITTINGS
Hose I.D.
Minimum
Burst
Pressure
Page
66
64
156
65
ADAPTERS &
TUBE FITTINGS
Part Number
Maximum
Operating
Pressure
ACCESSORIES &
GH781
MATCHMATE Plus
HI-IMPULSE
Double wire braid
Meets or exceeds:
SAE 100R16 Type S, EN857 2SC, ISO 11237-1 Type 2SC
r
mm
in
6,4
9,7
12,7
16,0
19,1
25,4
31,8
38,1
50,8
0.25
0.38
0.50
0.63
0.75
1.00
1.25
1.50
2.00
Construction
synthetic rubber cover. Meets or
exceeds EN requirements at 1/2
SAE Bend Radius.
–40°C to +100°C [–40°F to +212°F]
Hose O.D.
mm
13,5
17,5
20,6
23,6
27,9
36,1
41,9
51,6
64,3
in
bar
0.53
0.69
0.81
0.93
1.10
1.42
1.65
2.03
2.53
400,0
350,0
297,0
250,0
216,0
175,0
157,0
124,0
90,0
psi
5800
5000
4250
3625
3125
2500
2250
1800
1300
Application
bar
1600,0
1400,0
1190,0
1000,0
870,0
700,0
630,0
497,0
359,0
psi
23200
20000
17000
14500
12500
10000
9000
7200
5200
Minimum
Bend
Radius
mm
50,8
63,5
88,9
101,6
120,7
152,4
209,6
254,0
317,5
in
2.00
2.50
3.50
4.00
4.75
6.00
8.25
10.00
12.50
See pages 346-348.
Weight
of Hose
Kg/m
lbs/ft
0,33
0,43
0,58
0,65
0,79
1,07
1,62
2,08
2,83
0.22
0.29
0.39
0.44
0.53
0.72
1.09
1.40
1.90
Fitting Reference
Crimp
TTC
Skive Nipple *
Socket Data
HOSE ASSEMBLY
EQUIPMENT
GH781-4
GH781-6
GH781-8
GH781-10
GH781-12
GH781-16
GH781-20
GH781-24
GH781-32
Hose I.D.
Minimum
Burst
Pressure
APPENDICIES
Part Number
Maximum
Operating
Pressure
Page
66
66
64
*-04 thru -20 only
47
SPECIALTY &
TRUCK HOSE
GH793
MATCHMATE Plus
HI-IMPULSE
Double wire braid
Meets or exceeds:
LOW & MEDIUM
PRESSURE HOSE
r
Part Number
Hose I.D.
Hose O.D.
mm
mm
in
in
HIGH PRESSURE HOSE
HOSE FITTINGS
GH793-4
6,4
0.25
15,2
0.60
GH793-6
9,7
0.38
19,1
0.75
GH793-8
12,7
0.50
22,1
0.87
GH793-10
16,0
0.63
24,9
0.98
GH793-12
19,1
0.75
29,5
1.16
GH793-16
GH793-20
GH793-24
GH793-32
25,4
31,8
38,1
50,8
1.00
1.25
1.50
2.00
38,1
48,8
54,6
63,8
1.50
1.92
2.15
2.51
Construction
–40°C to +100°C [–40°F to +212°F]
Maximum
Operating
Pressure
bar
psi
400,0
350,0
350,0
280,0
297,0
245,0
250,0
192,0
216,0
157,0
175,0
140,0
157,0
124,0
90,0
5800†
5000
5000†
4000
4250†
3500
3625†
2750
3125†
2250
2500†
2000
2250
1800
1300
Application
Minimum
Burst
Pressure
bar
1600,0
1400,0
1400,0
1120,0
1190,0
980,0
1000,0
770,0
870,0
630,0
700,0
560,0
630,0
497,0
359,0
psi
23200†
20000
20000†
16000
17000†
14000
14500†
11000
12500†
9000
10000†
8000
9000
7200
5200
Minimum
Bend
Radius
mm
Weight
of Hose
in
Kg/m
lbs/ft
101,6
4.00
0,39
0.26
127,0
5.00
0,57
0.38
177,8
7.00
0,68
0.46
203,2
8.00
0,80
0.54
241,3
9.50
0,98
0.66
304,8
419,1
508,0
635,0
12.00
16.50
20.00
25.00
1,50
2,29
2,50
3,30
1.01
1.54
1.68
2.22
See pages 346-348.
†Improved pressure performance
ADAPTERS &
TUBE FITTINGS
Fitting Reference
Crimp
TTC
Skive Nipple
Socket Data
Reusable
Fitting
Socket Data
Page
66
66
64
165
65
ACCESSORIES &
GH195 AQP
MATCHMATE BLUE
HI-IMPULSE
Double wire braid
Meets or exceeds:
SAE 100R2AT Type S, EN853 2SN ISO 1436-1 Type 2SN
r
Part Number
HOSE ASSEMBLY
EQUIPMENT
GH195-4
GH195-6
GH195-8
GH195-10
GH195-12
GH195-16
GH195-20
GH195-24
GH195-32
Hose I.D.
mm
in
6,4
9,7
12,7
16,0
19,1
25,4
31,8
38,1
50,8
0.25
0.38
0.50
0.63
0.75
1.00
1.25
1.50
2.00
APPENDICIES
Construction
AQP elastomer tube, double
–40°C to +150°C [–40°F to +302°F]
48
Hose O.D.
mm
15,2
19,1
22,1
25,2
29,5
37,9
48,8
54,6
67,8
Maximum
Operating
Pressure
in
bar
psi
0.60
0.75
0.87
0.99
1.16
1.49
1.92
2.15
2.67
400,0
350,0
297,0
227,0
210,0
175,0
157,0
122,0
105,0
5800
5000
4250
3250
3000
2500
2250
1750
1500
Application
Petroleum and fire resistant
hydraulic fluids, fuel and lubricating systems. For more information on specific fluid applications
see pages 349-355.
Minimum
Burst
Pressure
bar
psi
1600,0
1400,0
1190,0
897,0
840,0
700,0
630,0
490,0
420,0
23200
20000
17000
13000
12000
10000
9000
7000
6000
Minimum
Bend
Radius
mm
101,6
127,0
177,8
203,2
241,3
304,8
419,1
508,0
635,0
in
Kg/m
lbs/ft
4.00
5.00
7.00
8.00
9.50
12.00
16.50
20.00
25.00
0,40
0,60
0,68
0,80
1,00
1,44
2,39
2,60
3,38
0.27
0.39
0.46
0.54
0.67
0.97
1.60
1.74
2.27
See pages 346-348.
Weight
of Hose
Fitting Reference
Crimp
TTC
Skive Nipple
Socket Data
Page
66
66
64
SPECIALTY &
TRUCK HOSE
FC195 AQP
HI-IMPULSE
Double wire braid
LOW & MEDIUM
PRESSURE HOSE
Meets or exceeds:
r
mm
mm
in
in
FC195-04
6,4
0.25
17,5
0.69
FC195-06
9,7
0.38
21,3
0.84
FC195-08
12,7
0.50
24,6
0.97
FC195-10
16,0
0.63
27,7
1.09
FC195-12
19,1
0.75
31,8
1.25
FC195-16
25,4
1.00
39,6
1.56
FC195-20
31,8
1.25
50,8
2.00
FC195-24
38,1
1.50
57,2
2.25
FC195-32
50,8
2.00
69,9
2.75
Construction
AQP elastomer tube, double
–40°C to +150°C [–40°F to +302°F]
bar
psi
bar
psi
400,0
350,0
350,0
280,0
297,0
245,0
227,0
192,0
216,0
210,0
175,0
140,0
157,0
113,0
124,0
122,0
105,0
87,0
5800†
5000
5000†
4000
4250†
3500
3250†
2750
3125†
3000
2500†
2000
2250†
1625
1800†
1750
1500†
1250
1600,0
1400,0
1400,0
1120,0
1190,0
980,0
1000,0
770,0
870,0
630,0
700,0
560,0
630,0
455,0
497,0
350,0
420,0
315,0
23200†
20000
20000†
16000
17000†
14000
14500†
11000
12500†
9000
10000†
8000
9000†
6500
7200†
5000
6000†
4500
Application
Petroleum and fire resistant
hydraulic fluids, fuel, and lubricating systems. For more information on specific fluid applications
see pages 349-355.
mm
Weight
of Hose
in
Kg/m
lbs/ft
101,6
4.00
0,46
0.31
127,0
5.00
0,62
0.42
177,8
7.00
0,76
0.51
203,2
8.00
0,88
0.59
241,3
9.50
1,12
0.75
304,8
12.00
1,55
1.04
419,1
16.50
2,50
1.68
508,0
20.00
2,84
1.91
635,0
25.00
3,56
2.39
See pages 346-348.
† Improved pressure performance
when used with global crimp
fittings.
Fitting Reference
Crimp
Skive Nipple
Socket Data
Reusable
Fitting
Socket Data
HIGH PRESSURE HOSE
Hose O.D.
Minimum
Bend
Radius
HOSE FITTINGS
Hose I.D.
Minimum
Burst
Pressure
Page
66
64
ADAPTERS &
TUBE FITTINGS
Part Number
Maximum
Operating
Pressure
156
65
ACCESSORIES &
FC636
EPDM hose
Four spiral wire
r
mm
in
19,1
25,4
31,8
38,1
0.75
1.00
1.25
1.50
Construction
Synthetic EPDM tube, 4-spiral
wire reinforcement, and green
EPDM synthetic cover.
–40°C to +75°C (–40°F to +175°F).
Hose O.D.
mm
30,5
37,6
46,5
53,6
in
bar
psi
bar
psi
1.20
1.48
1.83
2.12
280,0
280,0
210,0
175,0
4000
4000
3000
2500
1120,0
1120,0
840,0
700,0
16000
16000
12000
10000
Application
(GSE), industrial phosphate ester
based fluids, water glycol systems. For more information on
pages 349-355.
Minimum
Bend
Radius
mm
241,3
304,8
419,1
508,0
Weight
of Hose
in
Kg/m
lbs/ft
9.50
12.00
16.50
20.00
1,31
1,74
2,31
2,90
0.88
1.17
1.55
1.96
See pages 346-348.
Fitting Reference
Crimp
TTC12
HOSE ASSEMBLY
EQUIPMENT
FC636-12
FC636-16
FC636-20
FC636-24
Hose I.D.
Minimum
Burst
Pressure
Page
66
APPENDICIES
Part Number
Maximum
Operating
Pressure
49
SPECIALTY &
TRUCK HOSE
FC323 AQP
High temperature
Four spiral wire
r
LOW & MEDIUM
PRESSURE HOSE
Part Number
HIGH PRESSURE HOSE
FC323-12
FC323-16
FC323-20
FC323-24
FC323-32
Hose I.D.
mm
in
19,1
25,4
31,8
38,1
50,8
0.75
1.00
1.25
1.50
2.00
Construction
AQP elastomer tube, 4-spiral
wire reinforcement and a blue
–40°C to +150°C [–40°F to +302°F]
Hose O.D.
mm
30,5
37,6
47,2
53,6
66,8
Maximum
Operating
Pressure
Minimum
Burst
Pressure
in
bar
psi
bar
psi
1.20
1.48
1.86
2.11
2.63
210,0
210,0
210,0
210,0
210,0
3000
3000
3000
3000
3000
840,0
840,0
840,0
840,0
840,0
12000
12000
12000
12000
12000
Application
petroleum, fire-resistant, and
water-base fluids, fuel, and lubricating systems. For more information on specific fluid applications and high temperature ratings, see pages 349-355.
Minimum
Bend
Radius
mm
241,3
304,8
419,1
508,0
635,0
Weight
of Hose
in
Kg/m
lbs/ft
9.50
12.00
16.50
20.00
25.00
1,40
1,82
2,53
3,27
4,78
0.94
1.22
1.70
2.20
3.21
See pages 346-348.
Fitting Reference
Crimp
Single Skive*
Internal Skive
Socket Data
* -12 thru -24 only
Page
106
118
64
HOSE FITTINGS
ADAPTERS &
TUBE FITTINGS
FC324 AQP
High temperature
Four spiral wire
r
Part Number
ACCESSORIES &
FC324-08
FC324-12
FC324-16
Hose I.D.
mm
in
12,7
19,1
25,4
0.50
0.75
1.00
Construction
–40°C to +150°C [–40°F to +302°F]
Hose O.D.
mm
23,1
30,5
37,6
Maximum
Operating
Pressure
in
bar
0.91
1.20
1.48
280,0
280,0
280,0
psi
4000
4000
4000
HOSE ASSEMBLY
EQUIPMENT
Application
Minimum
Burst
Pressure
bar
psi
1120,0
1120,0
1120,0
16000
16000
16000
mm
177,8
241,3
304,8
Weight
of Hose
in
Kg/m
lbs/ft
7.00
9.50
12.00
0,91
1,47
1,92
0.61
0.99
1.29
See pages 346-348.
APPENDICIES
50
Minimum
Bend
Radius
Fitting Reference
Page
Crimp
Single Skive (-12, -16) 106
Internal Skive (-12, -16) 118
Socket Data
64
Reusable
Fitting (-8 only)
169
Socket Data
65
SPECIALTY &
TRUCK HOSE
FC325 AQP
Four spiral wire
FC325-12
FC325-16
Hose I.D.
mm
in
19,1
25,4
0.75
1.00
Construction
–40°C to +150°C [–40°F to +302°F]
Hose O.D.
mm
32,0
38,6
in
bar
psi
bar
psi
1.26
1.52
350,0
350,0
5000
5000
1400,0
1400,0
20000
20000
Application
Minimum
Bend
Radius
mm
241,3
304,8
Weight
of Hose
in
Kg/m
lbs/ft
9.50
12.00
1,62
2,11
1.09
1.42
See pages 346-348.
Fitting Reference
Crimp
Internal Skive
Socket Data
Page
HIGH PRESSURE HOSE
Part Number
Minimum
Burst
Pressure
LOW & MEDIUM
PRESSURE HOSE
r
Maximum
Operating
Pressure
123
64
HOSE FITTINGS
GH493
MATCHMATE Plus
1/2 SAE bend radius
Four spiral wire
ADAPTERS &
TUBE FITTINGS
SAE 100R12, EN 856 Type R12
r
mm
mm
in
in
bar
psi
bar
psi
GH493-6
9,7
0.38
20,1
0.79
GH493-8
12,7
0.50
23,4
0.92
GH493-10
16,0
0.63
28,2
1.11
385,0
280,0
350,0
280,0
350,0
280,0
GH493-12
19,1
0.75
30,5
1.20
280,0
4000
1120,0
16000
GH493-16
25,4
1.00
37,6
1.48
280,0
4000
1120,0
16000
GH493-20
31,8
1.25
46,5
1.83
210,0
3000
840,0
12000
GH493-24
38,1
1.50
53,8
2.12
GH493-32
50,8
2.00
67,1
2.64
175,0
175,0
210,0‡
2500
2500
3000‡
700,0 10000
700,0 10000
840,0‡ 12000‡
Construction
Synthetic rubber tube, 4-spiral
wire reinforcement, black synthetic rubber cover.
–40°C to +121°C [–40°F to +250°F]
5500
4000*
5000
4000*
5000
4000*
1517,0
1120,0
1400,0
1120,0
1400,0
1120,0
22000
16000*
20000
16000*
20000
16000*
Application
for general industrial use. For
mm
in
62,5** 2.50**
125,0 5.00
90,0** 3.50**
180,0 7.00
100,0** 4.00**
200,0 8.00
120,0** 4.75**
240,0 9.50
150,0** 6.00**
300,0 12.00
210,0** 8.25**
420,0 16.50
250,0** 10.00**
500,0 20.00
320,0** 12.50**
640,0 25.00
*Pressure rating with TTC12
fittings and reusables
**1/2 SAE Bend Radius with
TTC12 fittings.
‡ Pressure rating with TTC12
fitting only.
See pages 346-348.
Weight
of Hose
Kg/m
lbs/ft
0,70
0.47
0,88
0.59
1,03
0.69
1,37
0.92
1,82
1.22
2,44
1.64
3,12
2.10
4,18
2.81
Fitting Reference
Crimp
TTC12
Single Skive
Internal Skive§
Socket Data
Reusable
Fitting
Socket Data
§ -16 thru -32 only
ACCESSORIES &
Hose O.D.
Minimum
Bend
Radius
HOSE ASSEMBLY
EQUIPMENT
Hose I.D.
Minimum
Burst
Pressure
Page
66
106
118
64
APPENDICIES
Part Number
Maximum
Operating
Pressure
169
65
51
SPECIALTY &
TRUCK HOSE
FC659
Flexible, 1/2 SAE bend radius
Four spiral wire
Exceeds SAE 100R12, EN856 Type R12
r
LOW & MEDIUM
PRESSURE HOSE
Part Number
HIGH PRESSURE HOSE
FC659-06
FC659-08
FC659-10
FC659-12
FC659-16
FC659-20
FC659-24
FC659-32
Hose I.D.
mm
in
9,7
12,7
16,0
19,1
25,4
31,8
38,1
50,8
0.38
0.50
0.63
0.75
1.00
1.25
1.50
2.00
Construction
wire reinforcement and synthetic
rubber cover.
HOSE FITTINGS
–40°C to +121°C [–40°F to +250°F]
Hose O.D.
mm
20,1
23,4
28,2
30,5
37,6
46,5
55,0
68,3
Maximum
Operating
Pressure
Minimum
Burst
Pressure
in
bar
psi
bar
0.79
0.92
1.11
1.20
1.48
1.83
2.17
2.69
280,0
280,0
280,0
280,0
280,0
210,0
175,0
175,0
4000
4000
4000
4000
4000
3000
2500
2500
1120,0
1120,0
1120,0
1120,0
1120,0
840,0
700,0
700,0
Application
petroleum and water-base fluids
requiring premium performance
and flexibility. For more specific
information on fluid applications,
see pages 349-355.
psi
16000
16000
16000
16000
16000
12000
10000
10000
mm
* 1/2 SAE Bend Radius
ACCESSORIES &
HOSE ASSEMBLY
EQUIPMENT
APPENDICIES
in
62,5* 2.50*
90,0* 3.50*
100,0* 4.00*
120,0* 4.75*
150,0* 6.00*
210,0* 8.25*
250,0* 10.00*
320,0* 12.50*
For Complete Agency Listing
See pages 346-348.
ADAPTERS &
TUBE FITTINGS
52
Minimum
Bend
Radius
Weight
of Hose
Kg/m
lbs/ft
0,70
0,85
1,04
1,34
1,80
2,43
3,06
4,44
0.47
0.57
0.70
0.90
1.21
2.40
2.06
2.99
Fitting Reference
Crimp
TTC12
Page
66
SPECIALTY &
TRUCK HOSE
FC736 BRUISER
Four spiral wire
Exceeds SAE 100R12, EN 856 Type R12
mm
mm
in
in
FC736-06
9,7
.38
20,1
.79
FC736-08
12,7
.50
23,4
.92
FC736-10
FC736-12
FC736-16
FC736-20
FC736-24
FC736-32
16,0
19,1
25,4
31,8
38,1
50,8
.63
.75
1.00
1.25
1.50
2.00
28,2
30,5
37,6
46,5
55,1
68,3
1.11
1.20
1.48
1.83
2.17
2.69
Construction
Synthetic rubber tube, 4-heavy
spiral wire reinforcement, synthetic rubber intermediate cover,
and BRUISER outer cover.
–40°C to +121°C (–40°F to +250°F)
bar
psi
bar
psi
385,0
280,0
350,0
280,0
350,0
280,0
280,0
280,0
210,0
175,0
175,0
5500
4000*
5000
4000*
5000
4000*
4000
4000
3000
2500
2500
1517,0
1120,0
1400,0
1120,0
1400,0
1120,0
1120,0
1120,0
840,0
700,0
700,0
22000
16000*
20000
16000*
20000
16000*
16000
16000
12000
10000
10000
Application
crical applications in construction,
forestry, and other off-highway
vehicles. BRUISER outer cover
offers unmatched abrasion,
chemical and environmental protection. For more information on
349-355.
mm
Weight
of Hose
in
Kg/m
lbs/ft
127,0
5.00
0,70
0.47
177,8
7.00
0,88
0.59
241,3
241,3
304,8
419,1
508,0
635,0
9.50
9.50
12.00
16.50
20.00
25.00
1,19
1,37
1,82
2,44
2,99
4,37
0.80
0.92
1.22
1.64
2.01
2.94
See pages 346-348.
*Pressure rating with TTC12
fittings and reusables.
HIGH PRESSURE HOSE
Hose O.D.
Fitting Reference
Page
Crimp
TTC12
66
Single Skive
106
Internal Skive (-16, -20) 118
Socket Data
64
Reusable
Fitting
169
Socket Data
65
HOSE FITTINGS
Hose I.D.
Minimum
Bend
Radius
ADAPTERS &
TUBE FITTINGS
Part Number
Minimum
Burst
Pressure
LOW & MEDIUM
PRESSURE HOSE
r
Maximum
Operating
Pressure
ACCESSORIES &
FC254
Four heavy spiral wire
Exceeds SAE 100R11, EN 856 4SP
r
mm
in
12,7
19,1
25,4
31,8
38,1
50,8
0.50
0.75
1.00
1.25
1.50
2.00
Construction
Synthetic rubber tube, 4-heavy
spiral wire reinforcement and
–40°C to +121°C [–40°F to +250°F]
Hose O.D.
mm
24,9
32,0
38,6
45,7
54,1
68,1
in
bar
psi
bar
psi
0.98
1.26
1.52
1.80
2.13
2.68
525,0
435,0
350,0
280,0
210,0
210,0
7500†
6250
5000
4000
3000
3000
2100,0
1750,0
1400,0
1120,0
840,0
840,0
30000
25000
20000
16000
12000
12000
Application
for general industrial use. For
more specific information on fluid
applications, see pages 349-355.
See pages 346-348.
Minimum
Bend
Radius
mm
203,2
279,4
304,8
419,1
508,0
635,0
Weight
of Hose
in
Kg/m
lbs/ft
8.00
11.00
12.00
16.50
20.00
25.00
0,70
0,88
1,03
1,37
1,82
2,44
0.47
0.59
0.69
0.92
1.22
1.64
† Rated at 10,000 psi for water
blast applications using internal
skive fittings.
* Available with BRUISER cover
as FC854-08.
HOSE ASSEMBLY
EQUIPMENT
FC254-08*
FC254-12
FC254-16
FC254-20
FC254-24
FC254-32
Hose I.D.
Minimum
Burst
Pressure
Fitting Reference
Page
Crimp
Spiral TTC
97
Internal Skive
118
Socket Data
64
APPENDICIES
Part Number
Maximum
Operating
Pressure
53
SPECIALTY &
TRUCK HOSE
FC273
Four or six spiral wire
SAE 100R13, EN 856 Type R13, ISO 3862 Type R13
r
LOW & MEDIUM
PRESSURE HOSE
Part Number
HIGH PRESSURE HOSE
FC273-12
FC273-16
FC273-20
FC273-24
FC273-32
Hose I.D.
mm
in
19,1
25,4
31,8
38,1
50,8
0.75
1.00
1.25
1.50
2.00
Construction
Synthetic rubber tube, multiple
heavy spiral wire (4 wire for -12,
-16; 6 wire for -20, -24 and -32);
black synthetic rubber cover.
–40°C to +121°C [–40°F to +250°F]
Maximum
Operating
Pressure
Hose O.D.
mm
32,0
38,6
49,8
57,4
71,1
in
bar
1.26
1.52
1.96
2.26
2.80
350,0
350,0
350,0
350,0
350,0
psi
5000
5000
5000
5000
5000
Application
Minimum
Burst
Pressure
bar
psi
1400,0
1400,0
1400,0
1400,0
1400,0
20000
20000
20000
20000
20000
Minimum
Bend
Radius
mm
240,0
300,0
420,0
500,0
640,0
Weight
of Hose
in
Kg/m
lbs/ft
9.50
12.00
16.50
20.00
25.00
1,56
1,96
3,66
4,70
7,11
1.05
1.32
2.46
3.16
4.78
See pages 346-348.
Fitting Reference
Crimp
Spiral TTC
Single Skive
Internal Skive
Socket Data
Page
97
113
123
64
HOSE FITTINGS
ADAPTERS &
TUBE FITTINGS
FC273B BRUISER
Four or six spiral wire
SAE 100R13, EN 856 Type R13, ISO 3862 Type R13
r
Part Number
ACCESSORIES &
FC273B-12
FC273B-16
FC273B-20
FC273B-24
FC273B-32
Hose I.D.
mm
in
19,1
25,4
31,8
38,1
50,8
0.75
1.00
1.25
1.50
2.00
HOSE ASSEMBLY
EQUIPMENT
Construction
Synthetic rubber tube, multiple
heavy spiral wire (4 wire for -12,
-16; 6 wire for -20, -24 and -32);
synthetic rubber intermediate
cover and BRUISER outer cover.
–40°C to +121°C [–40°F to +250°F]
Hose O.D.
mm
33,3
39,9
51,3
58,9
72,6
Maximum
Operating
Pressure
Minimum
Burst
Pressure
in
bar
psi
bar
1.31
1.57
2.02
2.32
2.86
350,0
350,0
350,0
350,0
350,0
5000
5000
5000
5000
5000
1400,0
1400,0
1400,0
1400,0
1400,0
Application
hydraulic system applications with
petroleum and water-based fluids.
Recommended for use on crical
applications in construction,
forestry, and other off-highway
vehicles. BRUISER outer cover
offers unmatched abrasion, chem-
psi
20000
20000
20000
20000
20000
mm
240,0
300,0
420,0
500,0
640,0
in
Kg/m
lbs/ft
1,55
1,95
3,63
4,78
7,05
1.04
1.31
2.44
3.21
4.74
See pages 346-348.
Weight
of Hose
9.50
12.00
16.50
20.00
25.00
ical and environmental protection.
fluid applications and temperature
APPENDICIES
54
Minimum
Bend
Radius
Fitting Reference
Crimp
Spiral TTC
Page
97
SPECIALTY &
TRUCK HOSE
GH506
Four spiral wire
EN 856 4SH
GH506-12*
GH506-16*
GH506-20*
GH506-24*
GH506-32*
Hose I.D.
mm
in
19,1
25,4
31,8
38,1
50,8
0.75
1.00
1.25
1.50
2.00
Construction
wire reinforcement, synthetic
rubber cover.
mm
32,3
38,4
45,5
53,6
68,1
in
bar
psi
bar
psi
1.27
1.51
1.79
2.11
2.68
420,0
380,0
350,0
300,0
250,0
6090
5510
5075
4350
3625
1680,0
1520,0
1400,0
1200,0
1000,0
24360
22040
20300
17400
14500
Application
Four wire hose for high pressure
hydraulic systems with petroleum and water-base fluids. For
mm
280,0
340,0
460,0
560,0
700,0
Weight
of Hose
in
Kg/m
lbs/ft
11.00
13.38
18.11
22.05
27.56
1,49
2,05
2,54
3,27
4,58
1.00
1.38
1.71
2.20
3.08
See pages 346-348.
* Also available as an M100 length
(GH506-12M100). This P/N is a minimum 100 feet in length.
Fitting Reference
Crimp
Spiral TTC
Page
97
ADAPTERS &
TUBE FITTINGS
HOSE FITTINGS
–40°C to +100°C [–40°F to +212°F]
Hose O.D.
Minimum
Bend
Radius
HIGH PRESSURE HOSE
Part Number
Minimum
Burst
Pressure
LOW & MEDIUM
PRESSURE HOSE
r
Maximum
Operating
Pressure
GH466
Six spiral wire
ACCESSORIES &
* -32 size is also available.
See bulletin A-HOSP-MS003-E for more information.
r
mm
in
31,8
38,1
1.25
1.50
Construction
rubber cover.
–40°C to +100°C [–40°F to +212°F]
Hose O.D.
mm
49,3
57,4
in
bar
psi
bar
1.94
2.26
420,0
420,0
6090
6090
1680,0
1680,0
Application
Six wire spiral hose for pressure
systems with extreme pressure
peaks. For use with petroleum
and water-base fluids. For more
psi
24000
24000
Minimum
Bend
Radius
mm
420,0
510,0
Weight
of Hose
in
Kg/m
lbs/ft
16.50
20.80
3,48
4,63
2.34
3.11
See pages 346-348.
Fitting Reference
Crimp
Spiral TTC
HOSE ASSEMBLY
EQUIPMENT
GH466-20
GH466-24
Hose I.D.
Minimum
Burst
Pressure
Page
97
APPENDICIES
Part Number
Maximum
Operating
Pressure
55
SPECIALTY &
TRUCK HOSE
FC606
Six spiral wire
SAE 100R15
r
LOW & MEDIUM
PRESSURE HOSE
Part Number
FC606-16
FC606-20
FC606-24
Hose I.D.
mm
in
25,4
31,8
38,1
1.00
1.25
1.50
HIGH PRESSURE HOSE
Construction
rubber cover.
–40°C to +121°C [–40°F to +250°F]
Maximum
Operating
Pressure
Hose O.D.
mm
41,9
49,5
58,4
in
bar
psi
1.65
1.95
2.30
420,0
420,0
420,0
6000
6000
6000
Application
High-pressure hydraulics, hydrostatic transmissions. For more
Minimum
Burst
Pressure
bar
psi
1680,0
1680,0
1680,0
24000
24000
24000
Minimum
Bend
Radius
mm
304,8
419,1
508,0
Weight
of Hose
in
Kg/m
lbs/ft
12.00
16.50
20.00
2,66
3,62
4,72
1.79
2.43
3.17
See pages 346-348.
Fitting Reference
Crimp
Spiral TTC
Internal Skive
Socket Data
Page
97
128
64
HOSE FITTINGS
ADAPTERS &
TUBE FITTINGS
FC606B BRUISER
Six spiral wire
SAE 100R15, ISO 3862 Type R15
r
ACCESSORIES &
Part Number
FC606B-16
FC606B-20
FC606B-24
Hose I.D.
mm
in
25,4
31,8
38,1
1.00
1.25
1.50
Construction
rubber intermediate cover and
BRUISER outer cover.
HOSE ASSEMBLY
EQUIPMENT
–40°C to +121°C [–40°F to +250°F]
Hose O.D.
mm
42,9
51,6
58,9
Maximum
Operating
Pressure
Minimum
Burst
Pressure
in
bar
psi
bar
psi
1.69
2.03
2.32
420,0
420,0
420,0
6000
6000
6000
1680,0
1680,0
1680,0
24000
24000
24000
Application
High-abrasion industrial and
critical applications in construction, forestry, and other off-highway vehicles. BRUISER outer
mm
304,8
419,1
508,0
in
Kg/m
lbs/ft
2,60
3,57
4,57
1.79
2.43
3.07
See pages 346-348.
Weight
of Hose
12.00
16.50
20.00
349-355
APPENDICIES
56
Minimum
Bend
Radius
Fitting Reference
Crimp
Spiral TTC
Page
97
SPECIALTY &
TRUCK HOSE
FC579
10,000 PSI Jack Hose
Double wire braid
Meets IJ100 requirements
bar
psi
700,0
700,0
10000
10000
Application
Hydraulic jacking system service
with petroleum and water-base
fluids. Meets the performance
requirements of the Material
Handling Institute Specification
IJ100. For more information on
pages 349-355.
bar
psi
1400,0 20000
1400,0 20000
mm
50,8
63,5
in
Kg/m
lbs/ft
2.00
2.50
0,33
0,43
0.22
0.29
See pages 346-348.
Fitting Reference
Crimp
TTC
Skive Nipple
Socket Data
Page
HIGH PRESSURE HOSE
–40°C to +100°C [–40°F to +212°F]
in
0.53
0.69
66
66
64
HOSE FITTINGS
Construction
mm
13,5
17,5
ADAPTERS &
TUBE FITTINGS
in
0.25
0.38
Weight
of Hose
ACCESSORIES &
mm
6,4
9,7
Hose O.D.
HOSE ASSEMBLY
EQUIPMENT
FC579-04
FC579-06
Hose I.D.
Minimum
Bend
Radius
APPENDICIES
Part Number
Minimum
Burst
Pressure
LOW & MEDIUM
PRESSURE HOSE
r
Maximum
Operating
Pressure
57

Hose Index

Transcription

Similar documents

Fluid Conveying - Hydraulic Supply Company

BASE YEAR PERIOD

Table of Contents

HyQuipLLC - Hyquip.net

hose fittings hose fittings