product catalogue

Transcription

product catalogue

PRODUCT CATALOGUE
INDEX
1 PUNCHES AND DIES
1 MODEL D
2 MODEL C
2b MODEL CD, CC, CK, CO, CR
3 MODEL CH
4 MODEL CHA
5 MODEL CHP
6 MODEL CHE
7 MODEL CHEP with ejector
8 MODEL CHD, CHC, CHK, CHO, CHR
9 MODEL CHED, CHEC, CHEK, CHEO, CHER with ejector
10 MODEL CHX
11 MODEL CHEX with ejector
12 PILOT PUNCH CHS
13 EJECTOR ACCESSORIES
14 DIE A
15 DIE AH
16 DIE AD, AC, AK, AO, AR
17 DIE AHD, AHC, AHK, AHO, AHR
18 DIE AX
19 DIE AHX
20 DIE CHROME STEEL
21 LOCATIONS FOR PUNCHES AND DIES
22 RECOMMENDED CLEARANCES FOR DIES
2 PRECISION PILLARS AND BUSHES
1
2
3
4
5
6
7
8
9
GUIDE PILLAR SFS
BUSHES SFS
GUIDE PILLAR EDM
DEMOUNTABLE BUSHES EDM
CLAMPING INFORMATION FOR EDM BUSHES, HOLE TOLERANCES
FOR EDM PILLARS, BUSHES
GUIDE PILLARS
DEMOUNTABLE GUIDE PILLARS
DEMOUNTABLE GUIDE BUSHES
CLAMPING INFORMATION & ASSEMBLY INSTRUCTION FOR
DEMOUNTABLE GUIDE BUSHES
3 DEMOUNTABLE BEARING BUSHES AND CAGES
1
2
3
4
5
6
GUIDE PILLARS STRAIGHT
PRECISION BALL BEARING BUSHES STRAIGHT SLEEVE
DEMOUNTABLE BALL BEARING BUSHES
BALL BEARING CAGE TYPE 1 AND TYPE 2
BALL BEARING BUSHES AND CAGES FOR STRIPPER PLATE
3 DEMOUNTABLE BEARING BUSHES AND CAGES CONTINUES
7
8
9
10
11
12
13
14
ASSEMBLY INSTRUCTIONS FOR BALL BEARING GUIDING
BALL BEARING CAGE TYPE 1 CHOICE OF PILLAR LENGTH
BALL BEARING CAGE TYPE 1 SELECTION OF BUSH AND BALL CAGE
LENGTH
SELECTION TABLE FOR BUSH AND BALL CAGE LENGTH, BALL
BEARING CAGE TYPE 1
BALL BEARING CAGE TYPE 2 CHOICE OF PILLAR LENGTH
BALL BEARING CAGE TYPE 2 SELECTION OF BUSH AND BALL CAGE
LENGTH
SELECTION TABLE FOR BUSH AND BALL CAGE LENGTH, BALL
BEARING CAGE TYPE 2
4 SPRINGS
1
2
3
4
5
6
7
8
LIGHT LOAD SPRINGS 10 - 16 MM, 20 MM
LIGHT LOAD SPRINGS 25 - 63 MM
INTERMEDIATE LOAD SPRINGS 10 - 16 MM, 20 MM
INTERMEDIATE LAOD SPRINGS 25 - 63 MM
HEAVY LOAD SPRINGS 10 - 16 MM, 20 MM
HEAVY LOAD SPRINGS 25 - 50 MM
EXTRA HEAVY LOAD SPRINGS 10 - 20 MM
EXTRA HEAVY LAOD SPRINGS 25 - 50 MM
7 DRILL BUSHES, SOCKET HEADS, SPRING SHOULDER SCREWS, DOWEL
PINS
1
2
3
4
5
6
DRILL BUSHES
SOCKET HEAD CAP SCREWS
SPRING SHOULDER SCREWS
DOWEL PINS
DOWEL PINS WITH INSIDE THREAD
EJECTOR PINS
9 SUPRA TOOLING
1 C7 / C12
2 PA 8, 14, 20, 35, 50, 65, 80, 100, 120
3 PAE 20, 35, 50, 65, 80, 100, 120
4 GUIDING VALUES FOR DIE CLEARANCE
TECHNICAL
INFORMATION
Raw material
PUNCH MODEL D
PRODUCT GROUP
(DIN 9861)
HWS
0120
HSS
0130
HWS=Tool steel, alloy
HSS=High speed steel
Hardness HRC
HWS
Head
HSS
Head
62  2
45  4
64  2
45  5
Lengths
Standard lengths
71 and 100 mm
Other lengths at request
Ordering example
Punch model D,HWS
5 x 71
 No. 0120 0500 071
D
0,5
0,6
0,7
0,8
0,9
1,0-1,1
1,2-1,3
1,4-1,5
1,6-1,7
1,8-1,9
2
2,1-2,2
2,3-2,5
2,6-2,9
3,0-3,4
3,5-3,9
4,0-4,4
4,5-4,9
5,0-5,4
5,5-5,9
6,0-6,4
6,5-7,4
7,5-8,4
8,5-9,4
9,5-10,4
10,5-11,4
11,5-12,4
12,5-13,4
13,5-14,4
14,5-15,0
15,1-16,0
16,1-17,0
17,1-18,0
18,1-19,0
19,1-20,0
20,1-21,0
21,1-22,0
22,1-23,0
23,1-24,0
24,1-25,0
25,1-26,0
26,1-27,0
27,1-28,0
28,1-29,0
29,1-30,0
30,1-31,0
31,1-32,0
D1
0,9
1,1
1,3
1,4
1,6
1,8
2
2,2
2,5
2,8
3
3,2
3,5
4
4,5
5
5,5
6
6,5
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
H
0,2
0,2
0,2
0,4
0,4
0,5
0,5
0,5
0,5
0,5
0,5
0,5
0,5
0,5
0,5
0,5
0,5
0,5
0,5
0,5
0,5
1
1
1
1
1
1
1
1
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
1,5
L
71
71
71
71
71
71
71
71
71
71
71
71
71
71
71
71
71
71
71
71
71
71
71
71
71
71
71
71
71
71
71
71
71
71
71
71
71
71
71
71
71
71
71
71
71
71
71
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
Oy Suomen EDM Ab
Yrittäjänkatu 20
FI-06150 PORVOO, FINLAND
www.suomenedm.fi
Tel. +358 19 5211400
Fax +358 19 669765
[email protected]
1-1
TECHNICAL
INFORMATION
Raw material
PUNCH MODEL C
PRODUCT GROUP
(DIN 9861)
HWS
0121
HSS
0131
HWS=Tool steel, alloy
Hardness HRC
HWS
Head
62  2
45  4
HSS
Head
64  2
45  5
Lengths
Standard lengths
71 and 100 mm
Ordering example
Punch C,HWS
5 x 71, L1=7, P=3,5
 No. 0121 0500 071 07 0350
STANDARD L1-LENGTH ON THE CHART.
OTHER LENGTHS AVAILABLE.
P
0,5-1,99
1,6-2,99
2,0-3,99
2,5-4,99
3,0-5,99
3,5-6,99
4,5-7,99
5,0-8,99
6,0-9,99
7,0-11,99
8,0-12,99
10,0-15,99
15,0-19,99
16,0-21,99
18,0-24,99
24,0-31,99
D
2
3
4
5
6
7
8
9
10
12
13
16
20
22
25
32
D1
3
4,5
5,5
6,5
8
9
10
11
12
14
15
18
22
24
27
34
L1
6
6
7
7
10
10
13
13
16
16
16
20
20
20
20
20
H
0,5
0,5
0,5
0,5
0,5
1
1
1
1
1
1
1,5
1,5
1,5
1,5
1,5
L
71
71
71
71
71
71
71
71
71
71
71
71
71
71
71
71
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
Model for calculating the B-length (R is normally 13 mm)
B  R2  ( R 
D P 2
)  L1
2
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358 19 5211400
Fax +358 19 669765
[email protected]
1-2
TECHNICAL
INFORMATION
Raw material
PUNCH MODEL CD, CC, CK, CO, CR
PRODUCT GROUP
HWS=12% Cr-alloyed
Tool steel
HWS
0142
0143
0144
0146
0145
CD
CC
CK
CO
CR
HSS
0132
0133
0134
0136
0135
Hardness HRC
HWS
Head
62  2
45  4
HSS
Head
64  2
45  5
Lengths
Standard lengths
71 and 100 mm
Ordering example
Punch
C0,HWS 8 x 71,
L1=13, P=7.0, W=3.0
 Product number
0146 0800 071 13 0700 0300
CD
Min
w
0,8
1
1,3
1,3
1,6
2
3,5
4,5
6
8
10
10
16
CC
Max
PG
2
3
4
5
6
8
10
13
16
20
22
25
32
CK
D
2
3
4
5
6
8
10
13
16
20
22
25
32
D1
L1
standard
3
6
4,5
6
5,5
7
6,5
7
8
10
10
13
12
16
15
16
18
20
22
20
24
20
27
20
34
20
CO
L1
long
9
9
10
10
13
16
20
20
25
25
25
25
25
CR
L
71
71
71
71
71
71
71
71
71
71
71
71
71
100
100
100
100
100
100
100
100
100
100
100
100
100
B  R2  ( R 
DW 2
)  L1
2
Oy Suomen EDM Ab
Yrittäjänkatu 20
FI-06150 PORVOO
www.suomenedm.fi
Tel. 019-5211400
Fax 019 – 669765
[email protected]
1-2 b
TECHNICAL
INFORMATION
Raw material
PUNCH MODEL CH
PRODUCT GROUP
HWS
0240
(ISO 8020 A)
HSS
0230
HWS=SIS 2260=SFS 908
HSS=SIS 2722=SFS 916
Hardness HRC
HWS
Head
62  2
45  4
HSS
Head
64  2
52  3
Lengths
Standard lengths
71 and 100 mm
Ordering example
Punch model CH,HWS
13 x 71
D
2
3
4
5
6
8
10
13
16
20
22
25
32
D1
3,5
5
6,5
8
9
11
13
16
19
23
25
28
35
L
71
71
71
71
71
71
71
71
71
71
71
71
71
100
100
100
100
100
100
100
100
100
100
100
100
100
 No. 0240 1300 071
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358 19 5211400
Fax +358 19 669765
[email protected]
1-3
TECHNICAL
INFORMATION
Raw material
PUNCH MODEL CHA
(ISO 8020 A)
AS CH BUT WITH DIFFERENT DLENGTH
PRODUCT GROUP
HWS
0240
HSS
0230
Hardness HRC
HWS
Head
62  2
45  4
HSS
Head
64  2
52  3
Lengths
Standard lengths
71 and 100 mm
Ordering example
Punch model CHA,HWS
11,5 x 71
 No. 0240 1150 071
D
D1
L
2,1-2,2
3,7
71
100
2,3-2,5
4
71
100
2,6-2,9
4,5
71
100
3-3,4
5
71
100
3,5-3,9
5,5
71
100
4-4,4
6,5
71
100
4,5-4,9
7
71
100
5-5,4
8
71
100
5,5-5,9
8,5
71
100
6-6,4
9
71
100
6,5-6,9
9,5
71
100
7-7,4
10
71
100
7,5-7,9
10,5
71
100
8-8,4
11
71
100
8,5-8,9
11,5
71
100
9-9,4
12
71
100
9,5-9,9
12,5
71
100
10-10,4
13
71
100
10,5-10,9
13,5
71
100
11-11,4
14
71
100
11,5-11,9
14,5
71
100
12-12,4
15
71
100
12,5-12,9
15,5
71
100
13-13,4
16
71
100
13,5-13,9
16,5
71
100
14-14,4
17
71
100
14,5-14,9
17,5
71
100
15-15,4
18
71
100
15,5-15,9
18,5
71
100
ALSO OTHER DIAMETERS AVAILABLE.
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358 19 5211400
Fax +358 19 669765
[email protected]
1-4
TECHNICAL
INFORMATION
Raw material
PUNCH MODEL CHP
PRODUCT GROUP
HWS
0241
(ISO 8020 B)
HSS
0231
Hardness HRC
HWS
Head
62  2
45  4
HSS
Head
64  2
53  3
Lengths
Standard lengths
71 and 100 mm
Ordering example
Punch
CHP,HWS 5 x 71,
L1=7, P=3,5
P
D
D1
0,5-1,9
1,3-2,9
1,3-3,9
1,3-4,9
1,6-5,9
2,5-7,9
4,0-9,9
5,0-12,9
8,0-15,9
12,0-19,9
15,0-21,9
16,5-24,9
24,5-31,9
2
3
4
5
6
8
10
13
16
20
22
25
32
3,5
5
6,5
8
9
11
13
16
19
23
25
28
35
L1
standard
6
6
7
7
10
13
16
16
20
20
20
20
20
L1
long
9
9
10
10
13
16
20
20
25
25
25
25
25
L
71
71
71
71
71
71
71
71
71
71
71
71
71
100
100
100
100
100
100
100
100
100
100
100
100
100
 No. 0241 0500 071 07 0350
B  R2  ( R 
D P 2
)  L1
2
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358 19 5211400
Fax +358 19 669765
[email protected]
1-5
TECHNICAL
INFORMATION
Raw material
PUNCH MODEL CHE
WITH EJECTOR
PRODUCT GROUP
(ISO 8020 E)
HWS
0340
HSS
0330
Hardness HRC
HWS
Head
62  2
45  4
HSS
Head
64  2
52  3
Lengths
Standard lengths
71 and 100 mm
Ordering example
D
5
6
8
10
13
16
20
22
25
32
D1
8
9
11
13
16
19
23
25
28
35
L
71
71
71
71
71
71
71
71
71
71
100
100
100
100
100
100
100
100
100
100
Punch model CHE,HWS
8 x 71
 No. 0340 0800 071
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358 19 5211400
Fax +358 19 669765
[email protected]
1-6
TECHNICAL
INFORMATION
Raw material
PUNCH MODEL CHEP (ISO 8020 F)
WITH EJECTOR
PRODUCT GROUP
HWS
0341
HSS
0331
Hardness HRC
HWS
Head
62  2
45  4
HSS
Head
64  2
53  3
Lengths
Standard lengths
71 and 100 mm
Ordering example
Punch CHEP,HWS 10 x
71, L1=16, P=5,0
 No. 0341 1000 071 16 0500
P
D
D1
3,0-4,9
3,0-5,9
3,0-7,9
4,5-9,9
6,0-12,9
8,0-15,9
12,0-19,9
15,0-21,9
16,5-24,9
24,0-31,9
5
6
8
10
13
16
20
22
25
32
8
9
11
13
16
19
23
25
28
35
L1
standard
7
10
13
16
16
20
20
20
20
20
L1
long
10
13
16
20
20
25
25
25
25
25
L
71
71
71
71
71
71
71
71
71
71
100
100
100
100
100
100
100
100
100
100
B  R2  ( R 
D P 2
)  L1
2
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358 19 5211400
Fax +358 19 669765
[email protected]
1-7
TECHNICAL
INFORMATION
Raw material
PUNCH MODEL CHD, CHC, CHK, CHO,
CHR (ISO 8020)
PRODUCT GROUP
CHD
CHC
CHK
CHO
CHR
HWS
0242
0243
0244
0246
0245
HSS
0232
0233
0234
0236
0235
Hardness HRC
HWS
Head
62  2
45  4
HSS
Head
64  2
52  3
Lengths
Standard lengths
71 and 100 mm
Ordering example
Punch
CH0,HWS 8 x 71,
L1=13, P=7.0, W=3.0
 Product number
0246 0800 071 13 0700 0300
CHD
Min
w
0,8
1
1,3
1,3
1,6
2
3,5
4,5
6
8
10
10
16
CHC
Max
PG
2
3
4
5
6
8
10
13
16
20
22
25
32
CHK
D
2
3
4
5
6
8
10
13
16
20
22
25
32
CHO
L1
L1
stand. long
3,5
6
9
5
6
9
6,5
7
10
8
7
10
9
10
13
11
13
16
13
16
20
16
16
20
19
20
25
23
20
25
25
20
25
28
20
25
35
20
25
CHR
D1
L
71
71
71
71
71
71
71
71
71
71
71
71
71
100
100
100
100
100
100
100
100
100
100
100
100
100
B  R2  ( R 
DW 2
)  L1
2
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358 19 5211400
Fax +358 19 669765
[email protected]
1-8
TECHNICAL
INFORMATION
Raw material
PUNCH MODEL
CHED, CHEC, CHEK, CHEO, CHER
WITH EJECTOR (ISO 8020)
PRODUCT GROUP
HWS
0342
0343
0344
0346
0345
CHED
CHEC
CHEK
CHEO
CHER
HSS
0332
0333
0334
0336
0335
Hardness HRC
HWS
Head
62  2
45  4
HSS
Head
64  2
52  3
Lengths
Standard lengths
71 and 100 mm
Ordering example
Punch
CHE0,HWS 10 x 71,
L1=16, P=10.0, W=5.0
 Product number
0346 1000 071 16 1000 0500
CHED
CHEC
Min
Max
W
2
2,5
3
4,5
6
6,3
8
10
10
16
PG
5
6
8
10
13
16
20
22
25
32
D
5
6
8
10
13
16
20
22
25
32
CHEK
CHEO
D1
L1
L1
8
9
11
13
16
19
23
25
28
35
stand.
7
10
13
16
16
20
20
20
20
20
long
10
13
16
20
20
25
25
25
25
25
CHER
L
71
71
71
71
71
71
71
71
71
71
100
100
100
100
100
100
100
100
100
100
B  R2  ( R 
DW 2
)  L1
2
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358 19 5211400
Fax +358 19 669765
[email protected]
1-9
TECHNICAL
INFORMATION
SPECIAL SHAPED PUNCH CHX
PRODUCT GROUP
Raw material
CHX
HWS
0249
HSS
0239
Hardness HRC
HWS
Head
62  2
45  4
HSS
Head
64  2
52  3
ALSO AVAILABLE COUNTERSUNK HEADED.
EXAMPLES OF SHAPES. ALSO OTHER SHAPES
AVAILABLE
Lengths
Standard lengths
71 and 100 mm
Ordering example
Punch
CHX, HWS 16 x 71,
L1=20, MODEL 2-23
+ REQUESTED
DIMENSIONS
 Product number
0249 1600 071 20 2-29
+ DIMENSIONS
Model for calculating the Blength (R normally 13 mm)
B
R2  ( R 
DW 2
)  L1
2
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358 19 5211400
Fax +358 19 669765
[email protected]
1-10
TECHNICAL
INFORMATION
SPECIAL SHAPED PUNCH CHEX
WITH EJECTOR
PRODUCT GROUP
Raw material
CHEX
HWS
0349
HSS
0339
Hardness HRC
HWS
Head
62  2
45  4
HSS
Head
64  2
52  3
AVAILABLE
Lengths
Standard lengths
71 and 100 mm
Ordering example
Punch
CHEX, HWS 16 x 71,
L1=20, MODEL 2-23
+ REQUESTED
DIMENSIONS
 Product number
0349 1600 071 20 2-29
+ DIMENSIONS
Model for calculating the Blength (R normally 13 mm)
B
R2  ( R 
DW 2
)  L1
2
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358 19 5211400
Fax +358 19 669765
[email protected]
1-11
TECHNICAL
INFORMATION
Raw material
PILOT PUNCH CHS
PRODUCT GROUP
(ISO 8020)
HWS
0248
HSS
0238
Hardness HRC
HWS
Head
62  2
45  4
HSS
Head
64  2
52  3
Lengths
Standard lengths
L= 56 - 90
Other lengths at request.
Ordering example
Pilot punch
CHS,HWS 8 x 71,
L1=13, P=3,5
P
D
D1
1,0-2,0
1,3-3,0
1,5-4,0
1,9-5,0
1,9-6,0
2,4-8,0
3,9-10,0
4,9-13,0
7,9-16,0
11,9-20,0
14,9-22,0
15,9-25,0
16,4-32,0
2
3
4
5
6
8
10
13
16
20
22
25
32
3,5
5
6,5
8
9
11
13
16
19
23
25
28
35
L1
stand.
6
6
7
7
10
13
16
16
20
20
20
20
20
L1
long
9
9
10
10
13
16
20
20
25
25
25
25
25
L
56-90
56-90
56-90
56-90
56-90
56-90
56-90
56-90
56-90
56-90
56-90
56-90
56-90
 No. 0248 0800 071 13 0350
B  R2  ( R 
DW 2
)  L1
2
Model for calculating the K-length
13  P / 2 

K  13 * sin arccos(
)  15
.
13


Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358 19 5211400
Fax +358 19 669765
[email protected]
1-12
EJECTOR ACCESSORIES
PRODUCT GROUP 3300/3301/1802
3300
3301
SPRING
D
-0,1
2,3
2,3
3
3,9
4,6
4,6
6
6
D1
-0,2
2
2
2,5
3,3
4
4
4,5
4,5
EJECTOR PIN
d
d1
H
-0,1
-0,1
0,3
0,7
2,1
1,5
1
2,1
1,5
1,5
3
1,5
2
3,5
1,5
2,3
4,5
1,5
2,5
4,5
1,5
3
5
3
4
6
3
POLYURETHAN EJECTORS
1802
LOCK SCREW
G
L
M3
M3
M4
M5
M6
M6
M8
M8
4
4
6
6
8
8
10
10
PRODUCT GROUP 3305
D
2
3
4,5
6
L
15
15
15
10
pcs/package
10
10
10
10
ORDERING EXAMPLE: PU-EJECTOR, D=2, L=15  PRODUCT NUMBER 3305 0200 15
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358 19 5211400
Fax +358 19 669765
[email protected]
1-13
TECHNICAL
INFORMATION
Raw material
DIE A
PRODUCT GROUP
HWS
0440
HSS
0430
Hardness HRC
HWS
62  2
HSS
64  2
Lengths
Standard lengths
L= 20 - 25 - 32
Ordering example
Die
A,HWS D=20, L=25, P=10,5
 No. 0440 20 1050 25
DIES DELIVERED WITH COUNTERBORE OR TAPER
RECESS.
P
1,5-3,2
1,5-5,0
3,0-7,2
5,0-8,8
7,0-11
9,0-13,8
11,0-16,5
13,0-19,8
16,0-26,0
22,0-28,0
26,0-38,0
30,0-48,0
D
8
10
13
16
20
22
25
32
38
40
50
63
B
4
4
5
5
5
6
6
6
8
8
8
10
L
20-25-32
20-25-32
20-25-32
20-25-32
20-25-32
20-25-32
20-25-32
20-25-32
20-25-32
25-32
25-32
25-32
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358 19 5211400
Fax +358 19 669765
[email protected]
1-14
TECHNICAL
INFORMATION
Raw material
DIE AH
PRODUCT GROUP
HWS
0540
HSS
0530
Hardness HRC
HWS
62  2
HSS
64  2
Lengths
Standard lengths
L= 20 - 25 - 32
Ordering example
Die AH,HWS
D=20, L=25, P=10,5
 No. 0540 20 1050 25
DIES DELIVERED WITH COUNTERBORE OR TAPER
RECESS.
P
1,5-3,2
1,5-5,0
3,0-7,2
5,0-8,8
7,0-11,0
9,0-13,8
11,0-16,5
13,0-19,8
16,0-26,0
22,0-28,0
26,0-28,0
30,0-48,0
D
8
10
13
16
20
22
25
32
38
40
50
63
 D2
11
13
16
19
23
25
28
35
41
44
54
67
B
4
4
5
5
5
6
6
6
8
8
8
10
L
20-25-32
20-25-32
20-25-32
20-25-32
20-25-32
20-25-32
20-25-32
20-25-32
20-25-32
25-32
25-32
25-32
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358 19 5211400
Fax +358 19 669765
[email protected]
1-15
TECHNICAL
INFORMATION
Raw material
DIE AD-AC-AK-AO-AR
PRODUCT GROUP
HWS
0442
0443
0444
0446
0445
AD
AC
AK
AO
AR
HSS
0432
0433
0434
0436
0435
Hardness HRC
HWS
62  2
HSS
64  2
Lengths
Standard lengths
L= 20 - 25 - 32
AD
Ordering example
Die AO,HWS
D=20, L=25, P=10,5, W=3,0
 No. 0446 20 1050 0300 25
W
Min
1,2
1,2
2
2,4
3,2
4
4,8
5,5
6,4
10
13
20
AC
P G
Max
3,2
5
7,2
8,8
11
13,8
16,5
19,8
26
28
36
48
AK
AO
AR
D
B
L
8
10
13
16
20
22
25
32
38
40
50
63
4
4
5
5
5
6
6
6
8
8
8
8
20-25-32
20-25-32
20-25-32
20-25-32
20-25-32
20-25-32
20-25-32
20-25-32
20-25-32
25-32
25-32
25-32
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358 19 5211400
Fax +358 19 669765
[email protected]
1-16
TECHNICAL
INFORMATION
Raw material
DIE AHD-AHC-AHK-AHO-AHR
PRODUCT GROUP
HWS
0542
0543
0544
0546
0545
AHD
AHC
AHK
AHO
AHR
HSS
0532
0533
0534
0536
0535
Hardness HRC
HWS
62  2
HSS
64  2
Lengths
Standard lengths
L= 20 - 25 - 32
Ordering example
Die AHO,HWS
D=20, L=25, P=10,5, W=3,0
 No. 0546 20 1050 0300 25
AHD
W
Min
1,2
1,2
2
2,4
3,2
4
4,8
5,5
6,4
10
13
20
AHC
P G
Max
3,2
5
7,2
8,8
11
13,8
16,5
19,8
26
28
36
48
AHK
AHO
AHR
D
D2
B
L
8
10
13
16
20
22
25
32
38
40
50
63
11
13
16
19
23
25
28
35
41
44
54
67
4
4
5
5
5
6
6
6
8
8
8
8
20-25-32
20-25-32
20-25-32
20-25-32
20-25-32
20-25-32
20-25-32
20-25-32
20-25-32
25-32
25-32
25-32
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358 19 5211400
Fax +358 19 669765
[email protected]
1-17
TECHNICAL
INFORMATION
Raw material
SPECIAL SHAPED DIE AX
PRODUCT GROUP
AX
HWS
0449
HSS
0439
Hardness HRC
HWS
62  2
AVAILABLE
HSS
64  2
Lengths
Standard lengths
L= 20 - 25 - 32
Ordering example
Die AX,HWS
D=20, L=25, MODEL 2-29
+ REQUESTED
DIMENSIONS
 No. 0449 20 25 2-29
+DIMENSIONS
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358 19 5211400
Fax +358 19 669765
[email protected]
1-18
TECHNICAL
INFORMATION
Raw material
SPECIAL SHAPED DIE AHX
PRODUCT GROUP
AHX
HWS
0549
HSS
0539
Hardness HRC
HWS
62  2
AVAILABLE
HSS
64  2
Lengths
Standard lengths
L= 20 - 25 - 32
Ordering example
Die AHX,HWS
D=20, L=25, MODEL 2-29
+ REQUESTED
DIMENSIONS
 No. 0549 20 25 2-29
+DIMENSIONS
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358 19 5211400
Fax +358 19 669765
[email protected]
1-19
TECHNICAL
INFORMATION
DIE, CHROME STEEL
PRODUCT GROUP
(DIN 9845)
0420
Raw material
13% Cr steel
UX200C13
Hardness HRC
60 - 62
P
Lengths
Standard lengths
L= 20 - 28 according to chart
Ordering example
Die, chrome steel
P=9,0 L=28 (long)
 No. 0420 0900 28
Note: The P dimensions for the
D1 length are available only
according to the chart.
1,0-1,8
1,9-2,6
2,7-3,0
3,1-3,3
3,4-4,0
4,1-5,0
5,1-6,0
6,1-7,0
7,1-8,0
8,1-9,0
9,1-10,0
10,1-11,0
11,1-12,0
12,1-13,5
13,6-15,0
15,1-16,5
16,6-18,0
18,1-20,0
20,1-22,0
22,1-24,0
24,1-26,0
26,1-28,0
28,1-30,0
30,1-32,5
32,6-35,0
35,1-38,0
38,1-42,0
42,1-45,0
45,1-48,0
D1
n6
6
7
7
7
8
10
12
15
15
18
18
22
22
26
26
30
30
35
35
42
42
48
48
55
55
62
62
70
70
D2
2,4
3,5
4
4
4,5
5
7
8
9
10
11
12
13
14,5
16
17,5
19
21
23
25
27
30
32
34
37
40
44
47
50
L
Short
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
28
28
28
28
28
28
28
28
28
28
28
28
28
28
L
Long
28
28
28
28
28
28
28
28
28
28
28
28
28
28
28
28
28
28
28
28
28
28
28
28
28
28
28
28
28
H
Z
r
3
3
3
3
3
3
3
3
3
3
3
3,5
3,5
3,5
3,5
3,5
3,5
3,5
3,5
4,5
4,5
4,5
4,5
4,5
4,5
6
6
6
6
0,005
0,005
0,005
0,005
0,005
0,005
0,01
0,01
0,01
0,01
0,01
0,01
0,01
0,01
0,01
0,01
0,01
0,02
0,02
0,02
0,02
0,02
0,02
0,02
0,02
0,02
0,02
0,02
0,02
0,3
0,4
0,4
0,4
0,4
0,4
0,6
0,8
0,8
0,8
0,8
0,8
0,8
0,8
0,8
1
1
1
1
1
1
1
1
1
1
1,6
1,6
1,6
1,6
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358 19 5211400
Fax +358 19 669765
[email protected]
1-20
LOCATIONS FOR PUNCHES AND DIES
PUNCHES W ITH CH-HEAD AND AH DIES
LA
LB
LC
LD
LE
LF
ON LE AND LF LOCATIONS PLEASE MENTION THE NUM BER OF DEGREES
A SERIES DIES
MATERIAL INFORMATION
WS
HWS
HSS
Tool steel
Tool steel with chrome
High speed steel
100Cr6
X155CrVMo121
S6-5-2
SFS 907
SFS 908
SFS 916
SIS2140
SIS2260
SIS2722
COMPOSITIONS (%)
WS
HWS
HSS
C
1,000
1,550
0,900
Si
0,250
0,300
0,450
Mn
0,350
0,300
0,400
P+S
0,030
0,030
0,030
Cr
1,500
12,000
4,100
Mo
V
W
0,700
5,000
1,000
1,800
6,400
WE DELIVER ALSO PUNCHES AND DIES OF MATERIALS ASP 23
AND HARDMETAL.
TiN COATINGS (HSS) AND DIAMOND COATINGS (HWS JA HSS).
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358 19 5211400
Fax +358 19 669765
[email protected]
1-21
RECOMMENDED CLEARANCES FOR DIES
CLEARANCES ON THE TABLE ARE GUIDE VALUES.
SPECIAL REQUIREMENTS ARE TO BE OBSERVED.
TOTAL CLEARANCES
Material
Thickness
mm
0,50
1,00
1,50
2,00
2,50
3,00
3,50
4,00
4,50
5,00
5,50
6,00
6,50
7,00
7,50
8,00
8,50
9,00
9,50
10,00
Fe37
mm
0,10
0,15
0,20
0,30
0,40
0,45
0,50
0,60
0,70
0,75
0,80
0,90
1,00
1,05
1,10
1,20
1,30
1,40
1,45
1,50
Stainless
steel
mm
0,15
0,20
0,25
0,35
0,45
0,50
0,55
0,65
0,75
0,80
0,85
0,95
1,05
1,10
1,15
1,25
1,35
1,45
1,50
1,55
Aluminium
soft
mm
0,05
0,10
0,15
0,25
0,35
0,40
0,45
0,55
0,65
0,70
0,75
0,85
0,95
1,00
1,05
1,15
1,25
1,35
1,40
1,45
Copper
soft
mm
0,05
0,10
0,15
0,25
0,35
0,40
0,45
0,55
0,65
0,70
0,75
0,85
0,95
1,00
1,05
1,15
1,25
1,35
1,40
1,45
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358 19 5211400
Fax +358 19 669765
[email protected]
1-22
PRECISION GUIDE PILLAR SFS
PRODUCT GROUP 1300
HA RD E N ED AN D FI NE G RO UN D
M AT ER I AL : CH RO M E NI CK E L ST E EL 1 8 Ni C rM o5 O R 16 CrN i 4
HA RD N E S S: SU RF AC E H AR D EN E D 6 2  2 HRc
L1 = PR E S SF IT T ING T O H 7
A V AI L A BL E AL S O W ITHO UT PR E S SF IT T ING : PR O D UCT G RO U P P 10
OTHER DIMENSIONS AVAILABLE AT REQUEST.
O RD E RI NG EX AM P L E : SF S - G U ID E P I LL A R  32 X 1 80

PR O DU CT NU M B ER 1 30 0
32 0 0 1 80
D L1
L
110 120 130 140 150 160 170 180 190 200 210 220 225 230 240 250 260 275 280 300 320 325 340 350 360 400
16 30 X
X
X
X
X
X
X
20 30 X
X
X
X
X
X
X
X
25 43
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
32 56
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
40 63
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
50 70
63 60
X
X
X
X
X
X
X
Oy Suomen EDM Ab
Yrittäjänkatu 20
FI-06150 PORVOO
www.suomenedm.fi
Tel. +358 19 5211400
Fax +358 19 669765
[email protected]
X
2-1
PRECISION BUSHES
SFS
PRODUCT GROUP 1400
HA RD E N ED AN D FI NE G RO UN D
M AT ER I AL : CH RO M E NI CK E L ST E EL 1 8 Ni C rM o5 O R 16 CrN i 4
HA RD N E S S: SU RF AC E H AR D EN E D 6 2  2 HRc
O UT ER D I A MET ER AT T HE O T HE R E ND LIG HT EN E D T O EN A B L E E A S Y MO UNT IN G .
AVAILABLE ALSO OTHER DIMENSIONS AT REQUEST.
O RD E RI NG EX A M PL E : SF S - B U SH  32 X 9 0
D
16
20
25
25
25
32
32
32
40
40
40
50
63

PR O D UCT N U M B ER 1 4 00 32 0 0 09 0
D1
25
30
38
38
38
48
48
48
60
60
60
72
90
L
46
60
40
80
120
40
90
140
60
110
160
120
135
Oy Suomen EDM Ab
Yrittäjänkatu 20
FI-06150 PORVOO
www.suomenedm.fi
Tel. +358 19 5211400
Fax +358 19 669765
[email protected]
2-2
DEMOUNTABLE PRECISION GUIDE PILLAR EDM
PRODUCT GROUP 1301
D
D1
25
32,4
32
42,8
40
51,8
50
64,8
63
76,8
L
70
80
90
100
110
120
130
140
150
160
170
180
100
110
120
130
140
150
160
170
180
200
220
240
280
100
110
120
130
140
150
160
170
180
200
220
240
280
110
120
130
140
150
160
170
180
200
220
240
280
320
360
400
120
140
160
180
200
220
240
320
360
400
L1
long
Xmin
short
ex.short
24
68,5
43,5
24,5
30
64,5
45,5
24,5
37
81,5
48,5
24,5
45
86,5
51,5
24,5
49
93,5
53,5
24,5
HARDENED AND FINE GROUND
MATERIAL: CHROME NICKEL STEEL 18NiCrMo5
OR 16CrNi4
HARDNESS: SURFACE HARDENED 62  2 HRC
ORDERING EXAMPLE: EDM PILLAR 32 X 200
 PRODUCT NUMBER 1301 3200 200
D
25
32
40
50
63
Radius
A
20,8
26
30,5
37
43
Clamping
information
Pcs/pillar
B
28,3
3
33,5
3
38
3
44,5
3
50,5
3
Screw
M8 x 20
M8 x 20
M8 x 20
M8 x 20
M8 x 20
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358-19-5211400
Fax +358-19-669765
[email protected]
2-3
DEMOUNTABLE BUSH EDM, STEEL
DEMOUNTABLE BUSH EDM, BRONZE PLATED
PRODUCT GROUP 1401
PRODUCT GROUP 1402
TUOTERYHMÄ 1402
LONG TYPE
D
25
32
40
50
63
L
80
90
100
110
130
D1
38
45
54
65
81
D2
41
50
60
76
89
D3
44
53
63
79
92
L1
23
26
30
35
48
D1
38
45
54
65
81
D2
41
50
60
76
89
D3
44
53
63
79
92
L1
23
26
30
35
48
D2
37,5
45,5
53,5
71,5
83,5
D3
44
53
63
79
92
L1
23
30
38
48
61
SHORT TYPE
D
25
32
40
50
63
L
55
60
67
75
90
EXTRA SHORT TYPE
4D
25
32
40
50
63
L
36
43
51
61
74
D1
38
45
54
65
81
MAT ERIAL: 18NiCr Mo5 or 16Cr Ni4 ( s teel), UNI5275 (bronze plated)
HARDNESS: SURFACE HARDENED 62  2 HRC
O RDERING EX AMPLE: EDM BUSH ST EEL D=25, L=80 PRO DUCT NO . 1401 2500 080
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358-19-5211400
Fax +358-19-669765
[email protected]
2-4
CLAMPING INFORMATION FOR EDM BUSHES
(PRODUCT GROUPS 1401 / 1402)
D
25
32
40
50
63
Clamping information
Radius
Pcs/
A
B
bush
27,5
38,5
3
32
42,5
3
37
47,5
3
45
55,5
3
51,5
62
3
Screw
M8 x 20
M8 x 20
M8 x 20
M8 x 20
M8 x 20
HOLE TOLERANCES FOR EDM PILLARS AND BUSHES
DEMOUNTABLE BUSH EDM, 1401 / 1402
D
Hole in
upper plate H6
38 + 0,016
0
45 + 0,016
0
54 + 0,019
0
65 + 0,019
0
81 + 0,022
0
100 + 0,022
0
25
32
40
50
63
80
DEMOUNTABLE PILLAR EDM, 1301
D
25
32
40
50
63
80
Hole in
lower plate
H7
25 + 0,021
0
32 + 0,025
0
40 + 0,025
0
50 + 0,030
0
63 + 0,030
0
80 + 0,035
0
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358-19-5211400
Fax +358-19-669765
[email protected]
2-5
PRECISION GUIDE PILLAR
PRODUCT GROUP P10
FOR SLEEVE GUIDING
Pylvään
halkaisija
D1
Reijän
halkaisija
D R6
20
20
-0.024
-0.037
25
25
-0.024
-0.037
32
32
-0.029
-0.045
40
40
-0.029
-0.045
50
50
-0.029
-0.045
63
63
-0.035
-0.054
80
80
-0.037
-0.056
D1
20
25
32
40
50
63
80
d
M5
M6
M8
M10
M12
M16
M20
m
6
8
8
8
8
8
8
L
100
P10.020.100 P10.025.100
PRODUCT NUMBER
110
P10.020.110 P10.025.110 P10.032.110
125
P10.020.125 P10.025.125 P10.032.125 P10.040.125
140
P10.020.140 P10.025.140 P10.032.140 P10.040.140
160
P10.020.160 P10.025.160 P10.032.160 P10.040.160 P10.050.160
180
P10.020.180 P10.025.180 P10.032.180 P10.040.180 P10.050.180
200
P10.020.200 P10.025.200 P10.032.200 P10.040.200 P10.050.200 P10.063.200
220
P10.025.220 P10.032.220 P10.040.220 P10.050.220 P10.063.220
250
P10.025.250 P10.032.250 P10.040.250 P10.050.250 P10.063.250
280
P10.025.280 P10.032.280 P10.040.280 P10.050.280 P10.063.280 P10.080.280
315
P10.032.315 P10.040.315 P10.050.315 P10.063.315 P10.080.315
355
P10.040.355 P10.050.355 P10.063.355 P10.080.355
400
P10.050.400 P10.063.400 P10.080.400
450
P10.050.450 P10.063.450 P10.080.450
500
P10.080.500
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358-19-5211400
Fax +358-19-669765
[email protected]
2-6
DEMOUNTABLE PRECISION GUIDE PILLARS
PRODUCT GROUP P21
D1=D2
D3
E
d
m
Qty
Clamp
Screw
M
N
Q1
Q2
T
F
80
90
100
110
125
140
160
180
200
220
250
280
315
355
400
20
25
32
40
50
25
32
40
50
63
20
25
32
40
45
M5
M6
M8
M10
M12
6
8
8
8
8
3
3
3
3
4
B01.005.000 B01.006.000 B01.006.000 B01.008.000 B01.008.000
M5x12
M6x16
M6x16
M8x20
M8x20
16
20,3
24
30
36,5
22
27,5
31,5
39,3
45,8
16,5
20,6
22,6
26,5
38
22,2
27,8
31,3
38
38
10,5
14,7
14,7
17,5
17,5
PRODUCT NUMBER
P21.020.080 P21.025.080
P21.020.090 P21.025.090
P21.020.100 P21.025.100 P21.032.100 P21.040.100
P21.020.110 P21.025.110 P21.032.110 P21.040.110 P21.050.110
P21.020.125 P21.025.125 P21.032.125 P21.040.125 P21.050.125
p21.020.140 P21.025.140 P21.032.140 P21.040.140 P21.050.140
p21.020.160 P21.025.160 P21.032.160 P21.040.160 P21.050.160
P21.025.180 P21.032.180 P21.040.180 P21.050.180
P21.025.200 P21.032.200 P21.040.200 P21.050.200
P21.032.220 P21.040.220 P21.050.220
P21.032.250 P21.040.250 P21.050.250
P21.032.280 P21.040.280 P21.050.280
P21.050.315
P21.050.355
P21.050.400
63
80
76
93
50
60
M16
M20
8
8
4
4
B01.008.000 B01.008.000
M8x20
M8x20
42,5
51
51,8
60,3
42,2
48,3
42,2
48,3
17,5
17,5
P21.063.125
P21.063.140
P21.063.160
P21.063.180
P21.063.200
P21.063.220
P21.063.250
P21.063.280
P21.063.315
P21.063.355
P21.063.400
P21.080.200
P21.080.220
P21.080.250
P21.080.280
P21.080.315
P21.080.355
P21.080.400
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358-19-5211400
Fax +358-19-669765
[email protected]
2-7
DEMOUNTABLE GUIDE BUSHES STEEL
PRODUCT GROUP B10/B12
DEMOUNTABLE BRONZE-PLATED GUIDE BUSHES
EXTRA-LONG SHOULDER
D1
F
L
Product
number
Product
number
32
100
125
40
100
130
50
100
135
63
100
148
B10.032.100 B10.040.100 B10.050.100 B10.063.100
B20.032.100 B20.040.100 B20.050.100 B20.063.100
LONG SHOULDER
D1
F
L
Product
number
Product
number
25
75
97
32
75
100
40
75
105
50
75
110
63
75
123
B10.025.075 B10.032.075 B10.040.075 B10.050.075 B10.063.075
B20.025.075 B20.032.075 B20.040.075 B20.050.075 B20.063.075
NORMAL SHOULDER
D1
F
L
20
32
50
25
50
72
32
50
75
40
50
80
50
50
85
63
50
98
80
50
98
Product
number
B10.020.032 B10.025.050 B10.032.050 B10.040.050 B10.050.050 B10.063.050 B10.080.050
Product
number
B20.020.032 B20.025.050 B20.032.050 B20.040.050 B20.050.050 B20.063.050 B20.080.050
SHORT SHOULDER
D1
F
L
Product
number
Product
number
20
16
34
25
20
42
32
20
45
40
20
50
50
20
55
63
20
68
80
20
68
B10.020.016 B10.025.020 B10.032.020 B10.040.020 B10.050.020 B10.063.020 B10.080.020
B20.020.016 B20.025.020 B20.032.020 B20.040.020 B20.050.020 B20.063.020 B20.080.020
EXTRA-SHORT SHOULDER
D1
D3
F
E
L
X
Product
number
Product
number
20
29
10
18
28
6
25
36
10
23
33
6
32
43
10
30
40
10
40
50
14
38
52
10
50
64
14
48
62
20
63
79
14
61
75
20
80
99
14
78
92
32
B12.020.010 B12.025.010 B12.032.010 B12.040.014 B12.050.014 B12.063.014 B12.080.014
B22.020.010 B22.025.010 B22.032.010 B22.040.014 B22.050.014 B22.063.014 B22.080.014
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358-19-5211400
Fax +358-19-669765
[email protected]
2-8
CLAMPING INFORMATION
BRONZE-PLATED PRODUCT GROUP B20/B22
D1
D2
D3
D4
E
h
No. of
clamps
Clamp
Screw
M
N
Q1/R
Q2
T
20
28
29
32,5
18
3,3
25
38
42
47
22
5
32
45
49
54
25
5
40
54
58
63
30
5
50
65
70
75
35
5
63
81
88
93
48
5
80
100
110
115
48
5
2
3
3
4
4
4
4
B01.005.000 B01.006.000 B01.006.000 B01.008.000 B01.008.000 B01.008.000 B01.008.000
M5x12
M6x16
M6x16
M8x20
M8x20
M8x20
M8x20
19,5
27,5
31
37
43
52
63
25,5
35
38,2
46,3
52,3
61,3
72,3
24,4/23,5
26/27
30/31,5
33/37,5
37,5/46,5
43/57,5
34,3
37,1
44,1
49,3
57,1
66,6
10,5
14,7
14,7
17,5
17,5
17,5
17,5
EXTRA-SHORT SHOULDER
Prod.No. B12.020.010 B12.025.010 B12.032.010 B12.040.014 B12.050.014 B12.063.014 B12.080.014
Prod.No. B22.020.010 B22.025.010 B22.032.010 B22.040.014 B22.050.014 B22.063.014 B22.080.014
Clamp
B01.005.000 B02.006.000 B02.006.000 B02.008.000 B02.008.000 B02.008.000 B02.008.000
Screw
M5x12
M6x12
M6x12
M8x16
M8x16
M8x16
M8x16
M
19,5
30
33,5
40
46
55
66
N
25,5
38
41,5
51,2
57,2
66,7
77,2
Q1/R
25,2/23,5
26,9/27
33,7/31,5
36,5/37,5
41,5/46,5
46,7/57,5
Q2
36,5
39,5
49,0
54,2
62,5
71,6
ASSEMBLY INSTRUCTIONS
BRONZE-PLATED PRODUCT GROUP B20/B22
Nominal
diameter
D1
Bush diameter
Bore diameter
D2
D2 H6
Min./
max.
Adjustment
20
28 +0.021
+0.013
28 +0.013
+0.000
-0.000
-0.021
25
38 +0.025
+0.016
38 +0.016
+0.000
-0.000
-0.025
32
45 +0.025
+0.016
45 +0.016
+0.000
-0.000
-0.025
40
54 +0.030
+0.019
54 +0.019
+0.000
-0.000
-0.030
50
65 +0.030
+0.019
65 +0.019
+0.000
-0.000
-0.030
63
81 +0.035
+0.022
81 +0.022
+0.000
-0.000
-0.035
80
100 +0.035
+0.022
100 +0.022
+0.000
-0.000
-0.035
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358-19-5211400
Fax +358-19-669765
[email protected]
2-9
GUIDE PILLARS STRAIGHT
PRODUCT GROUP P10
Examples
D1
d
m
L
100
110
125
140
160
180
200
220
250
280
315
355
400
450
500
25
M6
8
P10.025.100
P10.025.110
P10.025.125
P10.025.140
P10.025.160
P10.025.180
P10.025.200
P10.025.220
P10.025.250
P10.025.280
32
M8
8
P10.032.110
P10.032.125
P10.032.140
P10.032.160
P10.032.180
P10.032.200
P10.032.220
P10.032.250
P10.032.280
P10.032.315
40
M10
8
PRODUCT NUMBER
P10.040.125
P10.040.140
P10.040.160
P10.040.180
P10.040.200
P10.040.220
P10.040.250
P10.040.280
P10.040.315
P10.040.355
50
M12
8
63
M16
8
P10.050.160
P10.050.180
P10.050.200
P10.050.220
P10.050.250
P10.050.280
P10.050.315
P10.050.355
P10.050.400
P10.050.450
P10.063.200
P10.063.220
P10.063.250
P10.063.280
P10.063.315
P10.063.355
P10.063.400
P10.063.450
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358-19-5211400
Fax +358-19-669765
[email protected]
3-2
PRODUCT GROUP P21
Examples
D1=D2
D3
E
d
m
Kiinnitin kpl
Kiinnitin
Ruuvi
M
N
Q1
Q2
T
F
80
90
100
110
125
140
160
180
200
220
250
280
315
355
400
25
32
40
50
63
32
25
M6
8
3
B01.006.000
M6x16
20,3
27,5
20,6
27,8
14,7
40
32
M8
8
3
B01.006.000
M6x16
24
31,5
22,6
31,3
14,7
50
40
M10
8
3
B01.008.000
M8x20
30
39,3
26,5
38
17,5
PRODUCT NUMBER
63
45
M12
8
4
B01.008.000
M8x20
36,5
45,8
38
38
17,5
76
50
M16
8
4
P21.025.100
P21.032.100
P21.040.100
P21.025.110
P21.032.110
P21.040.110
P21.050.110
P21.025.125
P21.032.125
P21.040.125
P21.050.125
P21.063.125
P21.025.140
P21.032.140
P21.040.140
P21.050.140
P21.063.140
P21.025.160
P21.032.160
P21.040.160
P21.050.160
P21.063.160
P21.025.180
P21.032.180
P21.040.180
P21.050.180
P21.063.180
P21.025.200
P21.032.200
P21.040.200
P21.050.200
P21.063.200
P21.032.220
P21.040.220
P21.050.220
P21.063.220
P21.032.250
P21.040.250
P21.050.250
P21.063.250
P21.032.280
P21.040.280
P21.050.280
P21.063.280
P21.050.315
P21.063.315
P21.050.355
P21.063.355
P21.050.400
P21.063.400
B01.008.000
M8x20
42,5
51,8
42,2
42,2
17,5
P21.025.080
P21.025.090
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358-19-5211400
Fax +358-19-669765
[email protected]
3-2
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358-19-5211400
Fax +358-19-669765
[email protected]
3-2
PRECISION BALL BEARING BUSHES
STRAIGHT SLEEVE PRODUCT GROUP B30
Examples
ASSEMBLY INSTRUCTIONS:
1. Decrease with acetone or a similar solvant and
thoroughly wipe clean the outer surface of the straight
sleeve bush and the inside of the plate bore and dry
the surfaces.
2. Apply a thin layer of Loctite 601 glue to both surfaces
and insert the bush into the hole while turning.
3. Leave to set for 4 hours at 22 C. Do not move the
bush before the glue has dried out.
D
25
32
40
50
63
D2
45
54
65
81
95
PRODUCT NUMBER
L
65
80
95
110
130
150
170
190
215
240
265
B30.025.065
B30.025.080
B30.032.080
B30.040.080
B30.025.095
B30.032.095
B30.040.095
B30.025.110
B30.032.110
B30.040.110
B30.050.110
B30.025.130
B30.032.130
B30.040.130
B30.050.130
B30.032.150
B30.040.150
B30.050.150
B30.063.150
B30.032.170
B30.040.170
B30.050.170
B30.063.170
B30.040.190
B30.050.190
B30.063.190
B30.040.215
B30.050.215
B30.063.215
B30.050.240
B30.063.240
B30.050.265
B30.063.265
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358-19-5211400
Fax +358-19-669765
[email protected]
3-3
DEMOUNTABLE BALL BEARING BUSHES
PRODUCT GROUP B40
Examples
D1
F
35
50
65
80
100
120
140
D2
D3
D4
E
D1
Qty
Screw
M
N
Q1/R
Q2
T
25
32
40
PRODUCT NUMBER
50
63
B40.025.050
B40.032.050
B40.040.050
B40.025.065
B40.032.065
B40.040.065
B40.050.065
B40.032.080
B40.040.080
B40.050.080
B40.040.100
B40.050.100
B40.063.100
B40.050.120
B40.063.120
B40.025.035
B40.063.140
45
49
54
30
54
58
63
30
65
70
75
30
81
88
93
50
95
103
108
50
25
3
32
3
FIXING CLAMPS
40
4
50
4
63
4
B01.006.000
B01.008.000
B01.008.000
B01.008.000
B01.008.000
M6x16
31
38,2
26/27
37,1
14,7
M8x20
37
46,3
30/31,5
44,1
17,5
M8x20
43
52,3
33/37,5
49,3
17,5
M8x20
52
61,3
37,5/46,5
57,1
17,5
M8x20
60
69,3
41,5/54
64,0
17,5
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358-19-5211400
Fax +358-19-669765
[email protected]
3-4
BALL BEARING CAGE TYPE 1 and TYPE 2
PRODUCT GROUP C11/C12
TYPE 1, C11
TYPE 2, C12
TYPE 1
C11
TYPE 1:
The ball bearing cage
remains inside the
bush and is in contact
with the pillar and the
bush.
TYPE 2:
The ball bearing cage
may come out of the
bush and is in this
way extending the
possible length of the
stroke.
TYPE 2
C12
TYPE 1
D1
25
C11.025.036 C1.025.048
Lc
S
36
11,5
32
48
17,5
C11.032.036 C11.032.048
Lc
S
36
11,5
40
48
17,5
C11.040.048 C11.040.060
Lc
S
48
17,5
60
23,5
50
C11.050.070 C11.050.084
Lc
S
70
28,5
84
35,5
63
C11.063.098
Lc
S
D1
25
98
42,5
TYPE 2
X
C12.025.055 C12.025.070 C12.025.090 C12.025.100 C12.025.110
Lc
S
32
70
35
90
42
100
50
110
60
C12.032.070 C12.032.090 C12.032.105 C12.032.115 C12.032.125 C12.032.135
Lc
S
40
70
35
90
43
105
50
115
60
125
70
135
80
C12.040.070 C12.040.085 C12.040.105 C12.040.115 C12.040.125 C12.040.135 C12.040.145 C12.040.155
Lc
S
50
70
36
85
43
105
51
115
61
125
71
135
81
145
91
155
103
C12.050.105 C12.050.120 C12.050.140 C12.050.150 C12.050.160 C12.050.170 C12.050.185 C12.050.195
Lc
S
63
55
27
7
105
51
120
61
140
71
150
81
160
91
170
103
185
116
195
128
C12.063.145 C12.063.165 C12.063.180 C12.063.190 C12.063.205 C12.063.215
Lc
S
145
72
165
82
180
92
190
105
205
117
215
130
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358-19-5211400
Fax +358-19-669765
[email protected]
3-5
BALL BEARING BUSHES AND CAGES FOR STRIPPER
PLATE PRODUCT GROUP B42/C13
BALL BEARING BUSHES FOR
STRIPPER PLATE
PRODUCT GROUP B42
BUSHES
D1
E
20
25
29
32
36
44
D2
D3
D4
25
B42.025.030
B42.025.035
45
43
54
32
40
PRODUCT NUMBER
B42.032.030
B42.032.035
B42.040.039
B42.032.042
B42.040.046
B42.040.054
54
65
50
64
63
75
50
B42.050.046
B42.050.054
81
79
93
FIXING CLAMPS
Quantity
Clamps
Screw
M
N
Q1/R
Q2
3
B02.006.000
M6x12
33,5
41,5
26,9/27
39,5
3
B02.006.000
M6x12
38
46
29,2/31,5
43,4
4
B02.006.000
M6x12
44
52
32,2/37,5
48,6
4
B02.006.000
M6x12
53
61
36,7/46,5
56,4
BALL BEARING CAGES FOR
STRIPPER PLATE
PRODUCT GROUP C13
BALL BEARING CAGES
D1
X
S
L
40
52
64
74
88
25
4,2
1,6
32
5,7
1,9
40
5,7
1,9
C13.025.040
C13.032.040
C13.025.052
C13.032.052
50
5,7
2,2
PRODUCT NUMBER
C13.040.052
C13.040.064
C13.050.074
C13.050.088
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358-19-5211400
Fax +358-19-669765
[email protected]
3-6
GUIDE PILLAR P10
PILLAR
DIAMETER
D
BORE
DIAMETER
D R6
25
25
-0.024
-0.037
32
32
-0.029
-0.045
40
40
-0.029
-0.045
50
50
-0.029
-0.045
63
63
-0.035
-0.054
GUIDE PILLAR P21
PILLAR
DIAMETER
D
25
32
40
50
63
-0.011
-0.020
-0.016
-0.025
-0.016
-0.025
-0.017
-0.029
-0.017
-0.029
BORE
DIAMETER
D R6
25
32
40
50
63
-0.024
-0.037
-0.029
-0.045
-0.029
-0.045
-0.029
-0.045
-0.035
-0.054
ADJUSTMENT
Min.
Max.
-0.004
-0.026
-0.004
-0.029
-0.004
-0.029
-0.000
-0.028
-0.006
-0.037
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358-19-5211400
Fax +358-19-669765
[email protected]
3-7
STRAIGHT SLEEVE
BALL BEARING BUSHES B30
Nominal
diameter
D1
Bush
diameter
D2 g4
Bore
diameter
D2 H6
Adjustment
Min.
Max.
25
45
-0.009
-0.016
45
+0.016
+0.000
+0.009
+0.032
32
54
-0.010
-0.018
54
+0.019
+0.000
+0.010
+0.037
40
65
-0.010
-0.018
65
+0.019
+0.000
+0.010
+0.037
50
81
-0.012
-0.022
81
+0.022
+0.000
+0.012
+0.044
63
95
-0.012
-0.022
95
+0.022
+0.000
+0.012
+0.044
STRAIGHT SLEEVE
BALL BEARING BUSHES B 40
Nominal
diameter
D1
Bush
diameter
D2
Bore
diameter
D2 H6
Adjustment
Min.
Max.
25
45 +0.025
+0.016
45 +0.016
+0.000
-0.000
-0.025
32
54 +0.030
+0.019
54 +0.019
+0.000
-0.000
-0.030
40
65 +0.030
+0.019
65 +0.019
+0.000
-0.000
-0.030
50
81 +0.035
+0.022
81 +0.022
+0.000
-0.000
-0.035
63
95 +0.035
+0.022
95 +0.022
+0.000
-0.000
-0.035
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358-19-5211400
Fax +358-19-669765
[email protected]
3-8
BALL BEARING CAGE
TYPE 1
CHOICE OF PILLAR LENGTH
TYPE 1: The cage is completely preloaded throughout the entire stroke.
PRELOAD
LINE
MIN. CLOSING
HEIGHT
(WORN DIE)
J1 = J2 = 4
Assembly conditions: The ball bearing cage has to be suspended on the retaining washer.
Calculating the the length of the pillars
PILLAR TYPE
BUSH TYPE
DEMOUNTABLE BUSH
STRAIGHT BUSH
STRAIGHT PILLAR
L=H-h-J1-C1+E-C2+Ec
L=H-h-J2-C2+EC
DEMOUNTABLE PILLAR
F=H-h-J1-C1+E-C2
F=H-h-J2-C2
N.B. If the correct guiding is not listed, please:
1. Choose a guide pillar of next length and cut it down to the required length. (N.B. Demountable bushes
should not be cut, choose a bush of next shorter length.)
2. Or, choose a guide pillar of next shorter length. Leave the pillar enough out of the die set plate in order to
reach the correct L-dimension.
The guide pillar has to be, if possible, inside the die set plate at least as much as the pillar is thick.
N.B. In TYPE 1 assemblies, a die set designed for certain stroke can be used in presses in which the stroke is
shorter, but not in presses in which the stroke is longer than in the original one.
WARNING: Verify that the bush is not hitting the punch plate at shut height. If the bush may hit the
punch plate, use a shorter bush and a ball bearing cage with the same length.
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358-19-5211400
Fax +358-19-669765
[email protected]
3-9
BALL BEARING CAGE
TYPE 1
SELECTION OF BUSH AND BALL CAGE LENGTH
The choice of a TYPE 1 bushing and ball cage unit is based upon the required stroke and the nominal diameter
of the pillar. When these two measurements are known, choose the components by referring to the table:
1. Choose the required stroke from the “Stroke C” column.
2. Follow this column down until you come to the coloured box situated in the row corresponding to the
required pillar diameter.
3. You will find the required length of bush on the same row by moving to the left from the coloured to
“Bush length” column. (N.B. Warning)
4. Choose the required length of ball bearing cage from “Ball bearing cage” column. Choose length that
has the same colour as the box where the stroke and the length are crossing. It is recommendable to
choose the length of the ball bearing cage as big as the shut height allows because the longer ball
bearing cage, the longer its life span.
If the choice is in the white area, use TYPE 2.
WARNING: Verify that the bush is not hitting the punch plate at shut height. If the bush may hit the
punch plate, use a shorter bush and a ball bearing cage with the same length.
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358-19-5211400
Fax +358-19-669765
[email protected]
3-10
BALL BEARING CAGE
TYPE 1
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358-19-5211400
Fax +358-19-669765
[email protected]
3-11
BALL BEARING CAGE
TYPE 2
CHOICE OF PILLAR LENGTH
TYPE 2: The ball bearing cage is no longer preloaded.
The stroke is restricted. The ball cage comes out of the bush
The ball cage leaves the preload zone but does not come out of
the bush.
The ball cage remains partially preloaded.
The ball cage remains fully
preloaded, i.e. under TYPE
1 working conditions.
Calculating the the pillar length
BUSH TYPE
PILLAR TYPE
DEMOUNTABLE BUSH
STRAIGHT PILLAR
L=H-h-J1-C1+E-C2+Ec
DEMOUNTABLE PILLAR
F=H-h-J1-C1+E-C2
STRAIGHT BUSH
L=H-h-J2-C2+EC
F=H-h-J2-C2
N.B. If the correct guiding is not listed, please:
1. Choose a guide pillar of next length up and cut it down to length L. (N.B. Demountable bushes should not be cut, choose a bush of
next shorter length.)
2. Or, choose a guide pillar of next shorter length. Leave the pillar enough out of the punch plate in order to reach the correct L-dimension.
The guide pillar has to be, if possible, inside the die set plate at least as much as it is thick.
Dn
 Nominal
PILLAR
a
h
25
32
40
50
63
6
6
6
8
8
9,3
10,4
11,5
12,6
16
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358-19-5211400
Fax +358-19-669765
[email protected]
3-12
BALL BEARING CAGE
TYPE 2
Instructions for use of the selection table for the choice of a TYPE 2 bushing and ball cage unit.
Choose TYPE 2 ball bearing bushing unit as follows:
1. Determine the required stroke.
2. Determine the required diameter of the pillar.
3. Determine the desired operating conditions or the height that the ball bearing cage rises above the bush.
4. Choose a demountable or straight sleeve bushing.
When you have determined these three factors: (1) stroke, (2) pillar diameter, (3) operating conditions and
(4) type of bushing, please see the selection table and:
Choose the required stroke from the “Stroke C” column. Follow this column down until you are level with the
required pillar diameter. Find the box corresponding to the desired operating conditions. Choose the longest
bush/ball bearing cage combination that closing height allows. In this way you will have the longest service life.
When you have determined the box, move to the left in the column and choose the length of the bushing and the
ball bearing cage. When you have determined these, refer to the pages giving the complete measurements and
order numbers for the different parts.
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358-19-5211400
Fax +358-19-669765
[email protected]
3-13
BALL BEARING CAGE
TYPE 2
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358-19-5211400
Fax +358-19-669765
[email protected]
3-14
LUBRICATION INSTRUCTIONS
FOR BALL BEARING GUIDING
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358-19-5211400
Fax +358-19-669765
[email protected]
3-15
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358-19-5211400
Fax +358-19-669765
[email protected]
3-16
LIGHT LOAD SPRINGS
PRODUCT GROUP 2000
Diameters: 10-16 mm


Hole
mm
Rod
mm
D
10
12,5
16
d
5
6,3
8
Colour: Green
LOAD
Free
length
mm
LOAD/DEFLECTION CHART
Rate
daN / mm
Catalogue
number
Lo
Total deflection
recommended for long
life
(25% of Lo)
Total deflection
recommended for
average life
(30% of Lo)
Maximum operating
deflection
Total travel to solid
(40% of Lo)
C
Load daN
Deflection mm
Load daN
Deflection mm
Load daN
Deflection
mm
Load daN
Deflection
mm
25
32
38
44
51
64
76
305
V10 025
V10 032
V10 038
V10 044
V10 051
V10 064
V10 076
V10 305
0,45
0,35
0,28
0,24
0,21
0,16
0,13
0,03
2,8
2,8
2,7
2,6
2,7
2,6
2,5
2,3
6,2
8,0
9,5
11
13
16
19
76
3,4
3,4
3,1
3,1
3,1
3
3
2,7
7,5
9,6
11
13
15
19
23
91
4,6
4,4
4,2
4,3
4,2
4
3,9
3,7
10,2
12,5
15
18
20
25
30
122
5,8
5,6
5,6
5,6
5,6
5,5
5,3
4,9
13
16
20
23
27
34
40
163
25
32
38
44
51
64
76
89
305
V13 025
V13 032
V13 028
V13 044
V13 051
V13 064
V13 076
V13 089
V13 305
0,89
0,67
0,55
0,46
0,39
0,30
0,25
0,21
0,06
5,5
5,4
5,2
5,1
5,1
4,8
4,8
4,6
4,6
6,2
8
9,5
11
13
16
19
22
76
6,7
6,4
6,1
6
5,9
5,7
5,7
5,7
5,5
7,5
9,6
11
13
15
19
23
27
91
9,1
8,4
8,3
8,3
7,8
7,5
7,5
7,6
7,3
10,2
12,5
15
18
20
25
30
36
122
11,6
11,4
11
10,6
10,5
10,5
10,3
10,3
10
13
17
20
23
27
35
41
49
166
25
32
38
44
51
64
76
89
102
305
V16 025
V16 032
V16 038
V16 044
V16 051
V16 064
V16 076
V16 089
V16 102
V16 305
1,79
1,34
1,06
0,87
0,76
0,59
0,48
0,40
0,35
0,11
11,1
10,7
10,1
9,6
9,9
9,4
9,1
8,8
9,1
8,4
6,2
8
9,5
11
13
16
19
22
26
76
13,4
12,9
11,7
11,3
11,4
11,2
11
10,8
10,8
10
7,5
9,6
11
13
15
19
23
27
31
91
18,3
16,8
15,9
15,7
15,2
14,8
14,4
14
14,3
13,4
10,2
12,5
15
18
20
25
30
35
41
122
23
21
21
20
20
20
19,7
19,6
19,6
18,7
13
16
20
23
27
34
41
49
56
170
Diameter :
20 mm Rectangular wire
Colour: Green


Hole
mm
Ro
d
mm
D
20
d
10
Load
Free
length
mm
Rate
daN / mm
Catalogue
number
Lo
25
32
38
44
51
64
76
89
102
115
127
140
152
305
V20 025
V20 032
V20 038
V20 044
V20 051
V20 064
V20 076
V20 089
V20 102
V20 115
V20 127
V20 140
V20 152
V20 305
Total deflection
life
(25% of Lo)
Total deflection
recommended for
average life
(30% of Lo)
Maximum operating
deflection
(40% of Lo)
C
Load daN
Deflection mm
Load daN
Deflection mm
Load daN
Deflection
mm
Load daN
Deflection
mm
5,5
4,2
3,3
2,77
2,45
1,90
1,61
1,34
1,18
1,04
0,93
0,85
0,79
0,38
35
34
32
31
32
31
31
30
31
30
30
30
30
29
6,2
8
9,5
11
13
16
19
22
26
29
32
35
38
76
42
41
37
37
37
37
37
36
37
36
35
36
36
35
7,5
9,6
11
13
15
19
23
27
31
35
38
42
46
91
57
54
51
51
50
49
48
47
48
48
47
48
48
46
10,2
12,5
15
18
20
25
30
35
41
46
51
56
61
122
73
69
65
64
64
62
62
62
62
62
62
62
62
61
13
16
19
23
26
32
40
46
53
60
67
73
81
162
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358 19 5211400
Fax +358 19 669 765
[email protected]
4-1
LIGHT LOAD SPRINGS
PRODUCT GROUP 2000
Diameters: 25-63 mm Rectangular wire Colour: Green
Load

Hole
mm
D
25
32
40
50
63

Rod
mm
d
Free
length
mm
Rate
daN / mm
Total deflection
recommended for average
life
(30% of Lo)
C
Load daN
Deflection
mm
Load daN
Deflection
mm
Load daN
Deflection
mm
Load daN
Deflection
mm
Catalogue
number
Lo
Total deflection
recommended for long life
(25% of Lo)
Maximum operating
deflection
(40% of Lo)
25
32
38
44
51
64
76
89
102
115
127
140
152
178
203
305
V25 025
V25 032
V25 038
V25 044
V25 051
V25 064
V25 076
V25 089
V25 102
V25 115
V25 127
V25 140
V25 152
V25 178
V25 203
V25 305
10,7
8,1
6,5
5,3
4,6
3,6
2,92
2,46
2,12
1,87
1,67
1,52
1,40
1,20
1,05
0,70
66
65
62
58
60
58
56
54
55
54
53
53
53
53
53
53
6,2
8,0
9,5
11
13
16
19
22
26
29
32
35
38
44
51
76
80
78
72
69
69
68
67
66
66
65
63
64
64
64
64
64
7,5
9,6
11
13
15
19
23
27
31
35
38
42
46
53
61
91
109
101
98
95
92
90
88
86
87
86
85
85
85
85
85
85
10,2
12,5
15
18
20
25
30
35
41
46
51
56
61
71
81
122
139
130
124
122
115
112
112
112
110
110
110
112
110
110
110
110
13
16
19
23
25
31
39
46
52
59
66
74
80
93
107
160
16
38
44
51
64
76
89
102
115
127
140
152
178
203
254
305
V32 038
V32 044
V32 051
V32 064
V32 076
V32 089
V32 102
V32 115
V32 127
V32 140
V32 152
V32 178
V32 203
V32 254
V32 305
10,1
8,3
7,1
5,5
4,6
3,9
3,4
3,0
2,62
2,38
2,19
1,82
1,59
1,25
1,04
96
91
92
88
87
86
88
87
84
83
83
80
81
80
79
9,5
11
13
16
19
22
26
29
32
35
38
44
51
64
76
111
108
107
105
106
105
105
105
100
100
101
96
97
95
95
11
13
15
19
23
27
31
35
38
42
46
53
61
76
91
152
149
142
138
138
137
139
138
134
133
134
129
129
128
127
15
18
20
25
30
35
41
46
51
56
61
71
81
102
122
192
183
178
176
175
175
175
174
170
171
170
165
165
163
161
19
22
25
32
39
45
52
58
65
72
78
88
104
130
155
20
51
64
76
89
102
115
127
140
152
178
203
254
305
V40 051
V40 064
V40 076
V40 089
V40 102
V40 115
V40 127
V40 140
V40 152
V40 178
V40 203
V40 254
V40 305
10,6
8,0
6,6
5,6
4,8
4,2
3,8
3,4
3,1
2,6
2,3
1,80
1,48
138
128
125
123
125
122
122
119
118
114
117
115
112
13
16
19
22
26
29
32
35
38
44
51
64
76
159
152
152
151
149
147
144
143
143
138
140
137
135
15
19
23
27
31
35
38
42
46
53
61
76
91
212
200
198
196
197
193
194
190
189
185
186
184
181
20
25
30
35
41
46
51
56
61
71
81
102
122
265
256
250
250
245
243
243
241
241
240
240
236
226
25
32
38
45
51
58
65
71
78
92
105
131
157
64
76
89
102
115
127
140
152
178
203
254
305
V50 064
V50 076
V50 089
V50 102
V50 115
V50 127
V50 140
V50 152
V50 178
V50 203
V50 254
V50 305
15,7
12,6
10,5
9,0
7,8
7,0
6,3
5,7
4,8
4,2
3,3
2,7
251
239
231
234
226
224
221
217
211
214
211
205
16
19
22
26
29
32
35
38
44
51
64
76
298
290
284
279
273
266
265
262
254
256
251
246
19
23
27
31
35
38
42
46
53
61
76
91
393
378
368
369
359
357
353
348
341
340
337
329
25
30
35
41
46
51
56
61
71
81
102
122
502
491
473
468
455
455
446
445
441
437
429
421
32
39
45
52
58
65
72
78
92
104
130
156
76
89
102
115
127
152
178
203
254
305
V63 076
V63 089
V63 102
V63 115
V63 127
V63 152
V63 178
V63 203
V63 254
V63 305
19,3
15,8
13,4
11,6
10,2
8,4
7,0
6,0
4,7
3,9
367
348
348
336
326
319
308
306
301
296
19
22
26
29
32
38
44
51
64
76
444
427
415
406
388
386
371
366
357
355
23
27
31
35
38
46
53
61
76
91
579
553
549
534
520
512
497
486
479
476
30
35
41
46
51
61
71
81
102
122
733
695
670
661
653
638
623
612
592
592
38
44
50
57
64
76
89
102
126
152
12,5
25
38
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358 19 5211400
Fax +358 19 669 765
[email protected]
4-2
INTERMEDIATE LOAD SPRINGS
PRODUCT GROUP 2001
Diameters: 10-16 mm Round spring wire


Hole
mm
Rod
mm
D
10
12,5
16
d
5
6,3
8
Colour: Blue
Load
Free
length
mm
Catalogue
number
Lo
Rate
daN /
mm
Total deflection
recommended for
long life
(25% of Lo)
Total deflection
recommended for
average life
(30% of Lo)
D
20

Rod
mm
d
10
(37,5% of Lo)
C
Load daN
Deflection
mm
Load daN
Deflection
mm
Load daN
Deflection
mm
Load daN
Deflection
mm
25
32
38
44
51
64
76
305
S10 025
S10 032
S10 038
S10 044
S10 051
S10 064
S10 076
S10 305
1,26
0,98
0,79
0,66
0,57
0,45
0,37
0,09
7,8
7,8
7,5
7,3
7,4
7,2
7,0
6,8
6,2
8,0
9,5
11
13
16
19
76
9,5
9,4
8,7
8,6
8,6
8,6
8,5
8,2
7,5
9,6
11
13
15
19
23
91
11,8
11,8
11,1
10,9
10,8
10,8
10,4
10,3
9,4
12
14
16,5
19
24
28
114
13,0
12,8
12,6
12,5
12,2
12,2
12,2
12,2
11
13
16
19
21
27
33
136
25
32
38
44
51
64
76
89
305
S13 025
S13 032
S13 028
S13 044
S13 051
S13 064
S13 076
S13 089
S13 305
2,28
1,75
1,43
1,18
1,02
0,79
0,65
0,55
0,15
14,1
14,0
13,6
13,0
13,3
12,6
12,4
12,1
11,4
6,2
8,0
9,5
11
13
16
19
22
76
17,1
16,8
15,7
15,3
15,3
15,0
15,0
14,9
13,7
7,5
9,6
11
13
15
19
23
27
91
21,4
21,0
20,0
19,5
19,4
19,0
18,2
18,2
17,1
9,4
12
14
16,5
19
24
28
33
114
23,0
22,8
22,8
22,5
22,4
22,1
22,0
22,6
21,6
11
13
16
19
22
28
34
41
144
25
32
38
44
51
64
76
89
102
305
S16 025
S16 032
S16 038
S16 044
S16 051
S16 064
S16 076
S16 089
S16 102
S16 305
3,38
2,50
2,01
1,67
1,42
1,10
0,90
0,76
0,66
0,21
20,6
20,0
19,1
18,4
18,5
17,6
17,1
16,7
17,2
16,0
6,2
8,0
9,5
11
13
16
19
22
26
76
25,4
24,0
22,1
21,7
21,3
20,9
20,7
20,5
20,5
19,1
7,5
9,6
11
13
15
19
23
27
31
91
31,8
30,0
28,1
27,6
27,0
26,4
25,2
25,1
25,1
23,9
9,4
12
14
16,5
19
24
28
33
38
114
33,8
32,8
32,2
30,9
30,0
29,7
29,7
29,6
29,6
29,0
11
13
16
19
21
27
33
39
45
138
Diameters : 20 mm Rectangular wire

Hole
mm
Maximum operating
deflection
Colour: Blue
Load
Free
length
mm
Catalogue
number
Lo
25
32
38
44
51
64
76
89
102
115
127
140
152
305
S20 025
S20 032
S20 038
S20 044
S20 051
S20 064
S20 076
S20 089
S20 102
S20 115
S20 127
S20 140
S20 152
S20 305
Rate
daN /
mm
Total deflection
recommended for
long life
(25% of Lo)
Total deflection
recommended for
average life
(30% of Lo)
Maximum operating
deflection
(37,5% of Lo)
C
Load daN
Deflection
mm
Load daN
Deflection
mm
Load daN
Deflection
mm
Load daN
Deflection
mm
9,02
6,67
5,48
4,45
3,94
3,03
2,49
2,14
1,84
1,63
1,46
1,32
1,21
0,61
55,9
53,4
52,1
49,0
51,2
48,5
47,3
47,1
47,8
47,3
46,7
46,0
46,0
46,4
6,2
8,0
9,5
11
13
16
19
22
26
29
32
35
38
76
67,6
64,0
60,3
57,9
59,1
57,6
57,3
57,8
57,0
57,0
55,5
55,0
55,7
55,5
7,5
9,6
11
13
15
19
23
27
31
35
38
42
46
91
84,8
80,0
76,7
73,4
74,9
72,7
69,7
70,6
69,9
70,1
70,1
69,0
69,0
69,5
9,4
12
14
16,5
19
24
28
33
38
43
48
52
57
114
99
90
88
85
83
82
82
82
81
80
80
80
80
80
11
13
16
19
21
27
33
39
44
49
55
61
66
136
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358 19 5211400
Fax +358 19 669 765
[email protected]
4-3
INTERMEDIATE LOAD
SPRINGS LOAD SPRINGS
PRODUCT GROUP2001
2001
INTERMEDIATE
Diameters : 25-63 mm Rectangular wire
Colour: Blue
Blue
Load

Hole
mm
D
25
32
40
50
63

Rod
mm
d
Free
length
mm
Rate
daN / mm
Catalogue
number
Lo
Total deflection
recommended for long life
(25% of Lo)
Total deflection
recommended for average
life
(30% of Lo)
Maximum operating
deflection
(37,5% of Lo)
C
Load daN
Deflection
mm
Load daN
Deflection
mm
Load daN
Deflection
mm
Load daN
Deflection
mm
25
32
38
44
51
64
76
89
102
115
127
140
152
178
203
305
S25 025
S25 032
S25 038
S25 044
S25 051
S25 064
S25 076
S25 089
S25 102
S25 115
S25 127
S25 140
S25 152
S25 178
S25 203
S25 305
16,7
12,5
9,9
8,3
7,2
5,5
4,5
3,8
3,3
2,91
2,63
2,36
2,17
1,84
1,60
1,05
104
100
94
91
94
88
86
84
86
84
84
83
82
81
82
80
6,2
8,0
9,5
11
13
16
19
22
26
29
32
35
38
44
51
76
125
120
109
108
108
105
104
103
102
102
100
99
100
98
98
96
7,5
9,6
11
13
15
19
23
27
31
35
38
42
46
53
61
91
157
150
139
137
137
132
126
125
125
125
126
123
124
123
122
120
9,4
12
14
16,5
19
24
28
33
38
43
48
52
57
67
76
114
184
170
158
158
156
151
148
148
145
145
145
149
145
145
144
142
11
13
16
19
21
27
33
39
44
60
66
63
67
79
90
135
16
38
44
51
64
76
89
102
115
127
140
152
178
203
254
305
S32 038
S32 044
S32 051
S32 064
S32 076
S32 089
S32 102
S32 115
S32 127
S32 140
S32 152
S32 178
S32 203
S32 254
S32 305
16,6
13,6
11,6
8,8
7,1
6,0
5,2
4,6
4,2
3,7
3,4
2,91
2,52
2,00
1,66
158
150
151
141
135
132
135
133
134
130
129
128
129
128
126
9,5
11
13
16
19
22
26
29
32
35
38
44
51
64
76
183
177
174
167
163
162
161
161
160
155
156
154
154
152
151
11
13
15
19
23
27
31
35
38
42
46
53
61
76
91
232
224
220
211
199
198
198
198
202
192
194
195
192
190
189
14
16,5
19
24
28
33
38
43
48
52
57
67
76
95
114
266
258
244
238
227
222
222
222
222
222
222
222
222
220
220
16
19
21
27
32
37
43
49
55
60
66
77
88
110
133
20
51
64
76
89
102
115
127
140
152
178
203
254
305
S40 051
S40 064
S40 076
S40 089
S40 102
S40 115
S40 127
S40 140
S40 152
S40 178
S40 203
S40 254
S40 305
17,1
12,9
10,5
8,8
7,6
6,7
6,0
5,4
4,9
4,2
3,6
2,89
2,38
222
206
200
194
198
194
192
189
186
185
184
185
181
13
16
19
22
26
29
32
35
38
44
51
64
76
257
245
242
238
236
235
228
227
225
223
220
220
217
15
19
23
27
31
35
38
42
46
53
61
76
91
325
310
294
290
289
288
288
281
279
281
274
275
271
19
24
28
33
38
43
48
52
57
67
76
95
114
359
335
335
326
326
322
322
319
318
318
315
315
312
21
26
32
37
43
48
54
59
65
76
87
110
131
25
64
76
89
102
115
127
140
152
178
203
229
254
305
S50 064
S50 076
S50 089
S50 102
S50 115
S50 127
S50 140
S50 152
S50 178
S50 203
S50 229
S50 254
S50 305
21,2
16,7
14,0
12,2
10,7
9,5
8,6
7,8
6,6
5,7
5,1
4,6
3,8
339
317
308
317
310
304
301
296
290
291
291
294
289
16
19
22
26
29
32
35
38
44
51
57
64
76
403
384
378
378
375
361
361
359
350
348
352
350
346
19
23
27
31
35
38
42
46
53
61
69
76
91
509
468
462
464
460
456
447
445
442
433
439
437
433
24
28
33
38
43
48
52
57
67
76
86
95
114
566
532
525
525
525
513
507
508
506
506
506
506
504
27
32
37
43
49
54
59
66
77
88
100
117
134
38
76
89
102
115
127
152
178
203
229
254
305
S63 076
S63 089
S63 102
S63 115
S63 127
S63 152
S63 178
S63 203
S63 229
S63 254
S63 305
30,4
25,0
21,2
18,6
16,4
13,3
11,2
9,6
8,5
7,7
6,3
578
550
551
539
525
505
493
490
485
493
479
19
22
26
29
32
38
44
51
57
64
76
699
675
657
651
623
612
594
586
587
585
573
23
27
31
35
38
46
53
61
69
76
91
851
825
806
800
787
758
750
730
731
732
718
28
33
38
43
48
57
67
76
86
95
114
973
950
933
930
918
891
874
865
865
865
865
32
38
44
50
56
67
78
90
102
115
138
12,5
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358 19 5211400
Fax +358 19 669 765
[email protected]
4-4
HEAVY LOAD SPRINGS
PRODUCT GROUP 2002
Diameters : 10-16 mm Round wire
Colour: Red
Load


Hole
mm
Rod
mm
D
10
12,5
16
d
5
6,3
8
Free
length
mm
Rate
daN / mm
Catalogue
number
Lo
Total deflection
life
(20% of Lo)
Total deflection
recommended for
average life
(25% of Lo)
Maximum operating
deflection
(30% of Lo)
C
Load daN
Deflection
mm
Load daN
Deflection
mm
Load daN
Deflection
mm
Load daN
Deflection
mm
25
32
38
44
51
64
76
305
P10 025
P10 032
P10 038
P10 044
P10 051
P10 064
P10 076
P10 305
2,13
1,64
1,33
1,13
0,98
0,78
0,63
0,15
10,5
10,5
10,0
10,0
10,0
10,0
9,5
9,0
5
6,5
7,5
9
10
13
15
61
13,0
13,0
12,5
12,5
12,5
12,5
12,0
11,5
6,2
8,0
9,5
11
13
16
19
76
16,0
15,5
14,5
14,5
14,5
14,5
14,5
13,5
7,5
9,6
11
13
15
19
23
91
19
19
18,5
18,5
18,5
18,5
18
18
8,9
11,7
14
17
19
25
29
120
25
32
38
44
51
64
76
89
305
P13 025
P13 032
P13 028
P13 044
P13 051
P13 064
P13 076
P13 089
P13 305
3,9
3,0
2,42
2,01
1,77
1,38
1,14
0,96
0,27
19,5
19,5
18
18
18
18
17
17,3
16,5
5
6,5
7,5
9
10
13
15
18
61
24
24
23
22
23
22
21,5
21,1
20,5
6,2
8,0
9,5
11
13
16
19
22
76
29
29
27
26
27
26
26
25,9
24,5
7,5
9,6
11
13
15
19
23
27
91
34
33
32
32
32
32
32
32
32
8,7
11,0
13,5
16
19
24
29
33
120
25
32
38
44
51
64
76
89
102
305
P16 025
P16 032
P16 038
P16 044
P16 051
P16 064
P16 076
P16 089
P16 102
P16 305
8,7
6,4
5,2
4,2
3,64
2,84
2,33
1,98
1,72
0,54
44
42
39
38
36
37
35
36
34
33
5
6,5
7,5
9
10
13
15
18
20
61
54
51
49
46
47
45
44
44
45
41
6,2
8,0
9,5
11
13
16
19
22
26
76
65
61
57
55
55
54
54
53
53
49
7,5
9,6
11
13
15
19
23
27
31
91
76
70
70
66
66
66
66
66
66
66
8,7
11
13,7
15,7
18,5
23,5
29
34,5
40
122
Diameters : 20 mm
Rectangular wire
Colour: Red
Load


Hole
mm
Rod
mm
D
20
d
10
Free
length
mm
Catalogue
number
Lo
25
32
38
44
51
64
76
89
102
115
127
140
152
305
Rate
daN / mm
P20 025
P20 032
P20 038
P20 044
P20 051
P20 064
P20 076
P20 089
P20 102
P20 115
P20 127
P20 140
P20 152
P20 305
Total deflection
life
(20% of Lo)
Total deflection
recommended for
average life
(25% of Lo)
Maximum operating
deflection
(30% of Lo)
C
Load daN
Deflection
mm
Load daN
Deflection
mm
Load daN
Deflection
mm
Load daN
Deflection
mm
23,1
17,4
13,9
11,4
9,8
7,7
6,3
5,4
4,7
4,1
3,7
3,4
3,08
1,50
116
113
106
103
101
100
97
97
94
94
93
95
92
91
5
6,5
7,5
9
10
13
15
18
20
23
25
28
30
61
143
139
132
127
127
128
120
120
120
119
118
119
117
114
6,2
8,0
9,5
11
13
16
19
22
26
29
32
35
38
76
173
167
153
148
147
146
145
145
145
144
141
143
141
137
7,5
9,6
11
13
15
19
23
27
31
35
38
42
46
91
194
183
174
165
162
162
162
162
162
162
162
167
162
162
8,4
10,5
12,5
14,5
16,5
21
26
30
35
40
44
49
53
108
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358 19 5211400
Fax +358 19 669 765
[email protected]
4-5
HEAVY LOAD SPRINGS
PRODUCT GROUP 2002
Colour: Red
Load


Hole
mm
Rod
mm
D
25
32
40
50
Free
length
mm
d
Lo
12,5
32
38
44
51
64
76
89
102
115
127
140
152
178
203
305
Rate
daN / mm
Catalogue
number
Total deflection
life
(20% of Lo)
Total deflection
recommended for
average life
(25% of Lo)
Maximum operating
deflection
(30% of Lo)
C
Load daN
Deflection
mm
Load daN
Deflection
mm
Load daN
Deflection
mm
Load daN
Deflection
mm
P25 032
P25 038
P25 044
P25 051
P25 064
P25 076
P25 089
P25 102
P25 115
P25 127
P25 140
P25 152
P25 178
P25 203
P25 305
27,6
22,0
18,4
15,7
12,2
10,0
8,4
7,4
6,5
5,8
5,2
4,8
4,1
3,59
2,42
179
165
166
157
159
150
151
148
150
145
146
144
148
144
148
6,5
7.5
9,0
10
13
15
18
20
23
25
28
30
36
40
61
221
209
202
204
195
190
185
192
189
186
182
182
180
183
184
8,0
9,5
11
13
16
19
22
26
29
32
35
38
44
51
76
265
242
239
236
232
230
227
229
228
220
218
221
217
219
220
9,6
11
13
15
19
23
27
31
35
38
42
46
53
61
91
290
286
285
283
275
275
275
275
275
273
270
273
273
273
273
10,5
13
15,5
18
22,5
27,5
32,5
37,5
42,7
47
52
57,5
68
77
115
16
38
44
51
64
76
89
102
115
127
140
152
178
203
254
305
P32 038
P32 044
P32 051
P32 064
P32 076
P32 089
P32 102
P32 115
P32 127
P32 140
P32 152
P32 178
P32 203
P32 254
P32 305
37,6
31,0
26,3
20,5
16,6
13,9
12,1
10,6
9,6
8,6
7,9
6,7
5,8
4,6
3,8
282
279
263
267
249
250
242
244
240
241
237
241
232
235
232
7,5
9,0
10
13
15
18
20
23
25
28
30
36
40
51
61
357
341
342
328
315
306
315
307
307
301
300
295
296
294
289
9,5
11
13
16
19
22
26
29
32
35
38
44
51
64
76
414
403
394
389
382
375
375
371
365
361
363
355
354
350
346
11
13
15
19
23
27
31
35
38
42
46
53
61
76
91
451
440
435
435
430
425
425
425
425
430
425
420
420
420
420
12
14
16,5
21,5
26
30,5
35,5
40,5
45
50
54
63
72
92
110
20
51
64
76
89
102
115
127
140
152
178
203
254
305
P40 051
P40 064
P40 076
P40 089
P40 102
P40 115
P40 127
P40 140
P40 152
P40 178
P40 203
P40 254
P40 305
34,9
26,6
21,5
18,0
15,7
13,8
12,4
11,3
10,2
8,7
7,6
6,0
5,0
349
346
323
324
314
317
310
316
306
313
304
306
305
10
13
15
18
20
23
25
28
30
36
40
51
61
454
426
409
396
408
400
397
396
388
383
388
384
380
13
16
19
22
26
29
32
35
38
44
51
64
76
524
505
495
486
487
483
471
475
469
461
464
456
455
15
19
23
27
31
35
38
42
46
53
61
76
91
593
585
580
575
575
575
575
588
575
575
575
575
575
17
22
27
32
37
42
47
52
57,5
67
76
97
116
64
76
89
102
115
127
140
152
178
203
254
305
P50 064
P50 076
P50 089
P50 102
P50 115
P50 127
P50 140
P50 152
P50 178
P50 203
P50 254
P50 305
42,3
33,8
28,1
24,5
21,5
18,9
16,9
15,4
13,2
11,5
9,0
7,5
550
507
506
490
495
473
473
462
475
460
459
457
13
15
18
20
23
25
28
30
36
40
51
61
677
642
618
637
624
605
592
585
581
587
576
570
16
19
22
26
29
32
35
38
44
51
64
76
804
777
759
760
753
718
710
708
700
701
684
683
19
23
27
31
35
38
42
46
53
61
76
91
910
879
860
860
860
850
845
830
830
830
825
825
21,5
26
30,5
35
40
45
50
54
64
72,5
92
112
25
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358 19 5211400
Fax +358 19 669 765
[email protected]
4-6
EXTRA HEAVY LOAD SPRINGS
PRODUCT GROUP 2003


Hole
mm
Rod
mm
D
10
12,5
16
20
d
5
6,3
8
10
Colour: Yellow
Load
Free
length
mm
Catalogue
number
Lo
Rate
daN /
mm
Total deflection
recommended for
long life
(17% of Lo)
Total deflection
recommended for
average life
(20% of Lo)
Maximum operating
deflection
(25% of Lo)
C
Load daN
Deflection
mm
Load daN
Deflection
mm
Load daN
Deflection
mm
Load daN
Deflection
mm
25
32
38
44
51
64
76
305
K10 025
K10 032
K10 038
K10 044
K10 051
K10 064
K10 076
K10 305
3,27
2,50
2,12
1,77
1,53
1,22
1,01
0,25
13,7
13,8
13,8
13,3
13,3
13,4
13,1
13,0
4,2
5,5
6,5
7,5
8,7
11
13
52
16.4
16,3
15,2
15,9
15,3
15,9
15,2
15,3
5
6,5
7,5
9
10
13
15
61
20,3
20,0
20,1
19,5
19,9
19,5
19,2
19,0
6,2
8,0
9,5
11
13
16
19
76
29,5
27,0
27,0
26,5
26,5
26,5
26,5
26,0
8,7
10,5
13,2
15,0
17,0
21,5
26,5
106
25
32
38
44
51
64
76
89
305
K13 025
K13 032
K13 038
K13 044
K13 051
K13 064
K13 076
K13 089
K13 305
5,87
4,43
3,63
3,06
2,71
2,17
1,77
1,51
0,42
24,7
24,4
23,6
23,0
23,6
23,9
23,0
22,7
21,8
4,2
5,5
6,5
7,5
8,7
11
13
15
52
29,4
28,8
27,2
27,5
27,1
28,2
26,6
27,2
25,6
5
6,5
7,5
9
10
13
15
18
61
36,4
35,4
34,5
33,7
35,2
34,7
33,6
33
31,9
6,2
8,0
9,5
11
13
16
19
22
76
53
48
47
47
47
47
47
50
47
9,0
10,8
13
15,5
18
22
27
33
112
25
32
38
44
51
64
76
89
102
305
K16 025
K16 032
K16 038
K16 044
K16 051
K16 064
K16 076
K16 089
K16 102
K16 305
12,6
9,3
7,5
6,3
5,5
4,3
3,52
3,00
2,61
0,85
53
51
49
47
48
47
46
45
44
44
4,2
5,5
6,5
7,5
8,7
11
13
15
17
52
63
60
56
57
55
56
53
54
52
52
5
6,5
7,5
9
10
13
15
18
20
61
78
74
71
69
72
69
67
66
68
65
6,2
8,0
9,5
11
13
16
19
22
26
76
113
103
98
96
96
95
94
94
94
94
9
10,8
13
15
18
22
26,5
31,5
36,5
110
25
32
38
44
51
64
76
89
102
115
127
140
152
305
K20 025
K20 032
K20 038
K20 044
K20 051
K20 064
K20 076
K20 089
K20 102
K20 115
K20 127
K20 140
K20 152
K20 305
32,2
24,2
19,5
16,3
14,0
10,9
9,0
7,6
6,6
5,8
5,2
4,7
4,3
2,12
135
133
127
122
122
120
117
114
112
116
114
113
112
110
4,2
5,5
6,5
7,5
8,7
11
13
15
17
20
22
24
26
52
161
157
146
147
140
142
135
137
132
133
130
132
129
129
5
6,5
7,5
9
10
13
15
18
20
23
25
28
30
61
202
194
185
179
182
174
171
167
172
168
166
165
163
161
6,2
8,0
9,5
11
13
16
19
22
26
29
32
35
38
76
248
237
234
228
225
225
225
225
225
220
220
221
220
220
7,7
9,8
12
14
16
21
25
30
34
38
43
47
51
105
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358 19 5211400
Fax +358 19 669 765
[email protected]
4-7
EXTRA HEAVY LOAD SPRINGS
PRODUCT GROUP 2003


Hole
mm
Rod
mm
D
25
32
40
50
Colour: Yellow
Load
Free
length
mm
d
Lo
12,5
32
38
44
51
64
76
89
102
115
127
140
152
178
203
305
Catalogue
number
Rate
daN /
mm
Total deflection
recommended for
long life
(17% of Lo)
Total deflection
recommended for
average life
(20% of Lo)
Maximum operating
deflection
(25% of Lo)
C
Load daN
Deflection
mm
Load daN
Deflection
mm
Load daN
Deflection
mm
Load daN
Deflection
mm
K25 032
K25 038
K25 044
K25 051
K25 064
K25 076
K25 089
K25 102
K25 115
K25 127
K25 140
K25 152
K25 178
K25 203
K25 305
35,4
28,0
23,2
19,8
15,4
12,5
10,5
9,1
8,1
7,2
6,6
6,0
5,1
4,5
2,96
195
182
174
172
169
163
158
155
162
158
158
156
153
153
154
5,5
6,5
7,5
8,7
11
13
15
17
20
22
24
26
30
34
52
230
210
209
198
200
188
189
182
186
180
185
180
184
180
181
6,5
7,5
9,0
10
13
15
18
20
23
25
28
30
36
40
61
283
266
255
257
246
238
231
237
235
230
231
228
224
230
225
8,0
9,5
11
13
16
19
22
26
29
32
35
38
44
51
76
354
336
325
317
316
313
310
310
310
310
317
310
310
310
310
10
12
14
16
21
25
29
34
39
43
48
53
62
70
108
16
38
44
51
64
76
89
102
115
127
140
152
178
203
254
305
K32 038
K32 044
K32 051
K32 064
K32 076
K32 089
K32 102
K32 115
K32 127
K32 140
K32 152
K32 178
K32 203
K32 254
K32 305
48,9
40,5
34,6
26,7
21,6
18,2
15,6
13,6
12,2
11,2
10,1
8,6
7,5
6,0
5,0
318
304
301
294
281
273
265
272
268
269
263
258
255
258
260
6,5
7,5
8,7
11
13
15
17
20
22
24
26
30
34
43
52
367
365
346
347
324
328
312
313
305
314
303
310
308
306
305
7,5
9,0
10
13
15
18
20
23
25
28
30
36
40
51
61
465
446
450
427
410
400
406
394
390
392
384
378
383
384
380
9,5
11
13
16
19
22
26
29
32
35
38
44
51
64
76
558
547
535
535
525
525
520
500
500
526
500
500
500
500
500
11
13
15
20
24
29
33
36
41
47
50
59
68
85
103
20
51
64
76
89
102
115
127
140
152
178
203
254
305
K40 051
K40 064
K40 076
K40 089
K40 102
K40 115
K40 127
K40 140
K40 152
K40 178
K40 203
K40 254
K40 305
56,0
42,2
34,3
28,2
24,4
21,4
19,0
17,1
15,6
13,2
11,4
9,1
7,5
487
464
446
423
415
428
418
410
406
396
388
391
390
8,7
11
13
15
17
20
22
24
26
30
34
43
52
560
549
525
508
488
492
475
479
468
475
456
464
458
10
13
15
18
20
23
25
28
30
36
40
51
61
714
675
652
620
634
621
608
599
593
581
581
582
570
13
16
19
22
26
29
32
35
38
44
51
64
76
840
820
815
800
800
792
780
787
780
765
765
765
760
15
19
24
28
33
37
41
46
50
58
67
85
102
64
76
89
102
115
127
140
152
178
203
254
305
K50 064
K50 076
K50 089
K50 102
K50 115
K50 127
K50 140
K50 152
K50 178
K50 203
K50 254
K50 305
72,4
57,3
47,4
40,4
35,3
31,2
28,2
25,5
21,5
18,6
14,6
12,1
796
745
711
687
706
686
677
663
645
632
628
629
11
13
15
17
20
22
24
26
30
34
43
52
941
860
853
808
812
780
790
765
774
744
745
738
13
15
18
20
23
25
28
30
36
40
51
61
1,158
1,089
1,043
1,050
1,024
998
987
969
946
949
934
920
16
19
22
26
29
32
35
38
44
51
64
76
1,376
1,318
1,280
1,252
1,235
1,217
1,241
1,200
1,200
1,190
1,170
1,170
19
23
27
31
35
39
44
47
56
64
80
97
25
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358 19 5211400
Fax +358 19 669 765
[email protected]
4-8
DRILL BUSHES STRAIGHT, DIN 179 (SMS 718)
PRODUCT GROUP 0700 / 0701
DRILL BUSHI DIN 179 SHORT
DRILL BUSH DIN 179 LONG
0700
0701
MATERIAL: NICKEL CHROMIUM STEEL
HARDNESS: 60-62 HRC
ORDERING EXAMPLE: DRILL BUSH DIN 179, SHORT,
D=15,0
 PRODUCT NUMBER 0700 1500
D F7
D1 n6
L
Short
0700
L
Long
0701
1,9-2,6
2,7-3,0
3,1-3,3
3,4-4,0
4,1-5,0
5,1-6,0
6,1-8,0
8,1-10,0
10,1-12,0
12,1-13,0
13,1-15,0
15,1-18,0
18,1-22,0
22,1-26,0
26,1-30,0
30,1-32,0
32,1-35,0
35,1-42,0
42,1-48,0
48,1-50,0
50,1-55,0
55,1-63,0
5
6
6
7
8
10
12
15
18
22
22
26
30
35
42
48
48
55
62
70
70
78
6
8
8
8
8
10
10
12
12
16
16
16
20
20
20
25
25
25
30
30
30
35
9
12
12
12
12
16
16
20
20
28
28
28
36
36
36
45
45
45
56
56
56
72
DRILL BUSH DEMOUNTABLE DIN 172 (SMS 719)
PRODUCT GROUP 0800 / 0801
DRILL BUSH DIN 172 SHORT
DRILL BUSH DIN 172 LONG
0800
0801
MATERIAL: NICKEL CHROMIUM STEEL
HARDNESS: 60-62 HRC
ORDERING EXAMPLE: DRILL BUSH
DIN 172, LONG, D=8,0
 PRODUCT NUMBER 0801 0800
Hard metal bushes on request.
D F7
D1
n6
D2
1,9-2,6
2,7-3,0
3,1-3,3
3,4-4,0
4,1-5,0
5,1-6,0
6,1-8,0
8,1-10,0
10,1-12,0
12,1-13,0
13,1-15,0
15,1-18,0
18,1-22,0
22,1-26,0
26,1-30,0
30,1-32,0
32,1-35,0
35,1-42,0
42,1-48,0
48,1-50,0
50,1-55,0
55,1-63,0
5
6
6
7
8
10
12
15
18
22
22
26
30
35
42
48
48
55
62
70
70
78
8
10
10
11
12
14
16
19
22
26
26
30
35
40
47
55
55
62
69
77
77
85
L1
Short
0800
6
8
8
8
8
10
10
12
12
16
16
16
20
20
20
25
25
25
30
30
30
35
L
Short
4
6
6
6
6
7
7
8
8
12
12
12
15
15
15
20
20
20
24
24
24
29
L1
Long
0801
9
12
12
12
12
16
16
20
20
28
28
28
36
36
36
45
45
45
56
56
56
72
L
Long
7
9
9
9
9
13
13
16
16
24
24
24
31
31
31
40
40
40
50
50
50
66
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358 19 5211400
Fax +358 19 669765
[email protected]
7-1
SOCKET HEAD CAP SCREW ISO 12.9
PRODUCT GROUP 1500
MAT ERIAL : HIG H ALLO YED ST EEL
ST RENG T H CL ASS: 12,9 (DIN/ISO 898)
HARDNESS: 37 - 43 HRC
T ENSILE ST RENG T H : 1200 N/m m 2
YIELD ST RENG T H : 1080 N/m m 2
SHEARING RESIST ANCE : 720 N/m m 2
ORDERING EXAMPLE: SOCKET HEAD CAP SCREW D=12, D1=M10, L=80PRODCUT NUMBER 1500 10
12 080
L
D2
H
L1
10
12
16
20
25
30
35
40
45
50
55
60
70
80
90
100
120
6 / M5
10
4,5
9,5
X
X
X
X
X
X
X
X
8 / M6
13
5,5
11
X
X
X
X
X
X
X
X
X
10 / M8
16
7
13
X
X
X
X
X
X
X
X
X
X
X
X
D/D1
12 / M10
18
8
16
X
X
X
X
X
X
X
X
X
X
X
X
X
X
16 / M12
24
10
18
20 / M16
30
14
22
24 / M20
36
16
27
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358 19 5211400
Fax +358 19 669765
[email protected]
7-2
SPRING SHOULDER SCREW ISO 12.9
PRODUCT GROUP 1501
SCREW : ST EEL ISO 12.9 ( UNI 5931 DIN 912)
W ASHER : HARDENED
BUSH : HARDENED J A G RO UND ( tol. h9)
BUSH HARDNESS: 40 - 50 HRC
O RDERING EX AMPLE I: SPRING HO LDER SCREW
NUMBER 1501 M10 090
D
D1
D2
H
L
20
25
30
35
40
45
50
55
60
70
80
90
100
120
10
M6
15
10
X
X
X
X
X
X
X
X
X
12,5
M8
19
13
15
M10
23
15
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
D=15, D1=M10, L=90 PRO DUCT
17,5
M12
27
18
X
X
X
X
X
X
X
X
X
X
23
M16
34
24
X
X
X
X
X
X
X
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358 19 5211400
Fax +358 19 669765
[email protected]
7-3
DOWEL PINS
DIN 6325
PRODUCT GROUP 1000
DIAMETER TOLERANCE: m6
HARDENED, ANNEALED, GROUND AND ADJUSTING GROUND
HARDNESS: 60  2 HRC
D
L
8
10
12
14
16
18
20
24
28
30
32
36
40
45
50
55
60
70
80
90
100
120
140
2
X
X
X
X
X
X
X
X
X
X
X
X
X
2,5
X
X
X
X
X
3
4
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
5
6
8
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
10
12
14
16
18
20
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358 19 5211400
Fax +358 19 669765
[email protected]
7-4
DOWEL PINS WITH INSIDE THREAD DIN 7979
PRODUCT GROUP 1200
AIR CHANNEL EASIFIES
DETACHING
DIAMETER TOLERANCE: m6
HARDENED, ANNEALED, GROUND AND ADJUSTING GROUND
HARDNESS: 60  2 HRC
L
20
22
24
28
30
32
35
38
40
45
50
55
60
70
80
90
100
120
140
6 / M4
X
X
X
X
X
X
X
X
X
X
X
X
X
8 / M5
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
10 / M6
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
D/G
12 / M6
14 / M8
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
16 / M8
18 / M8
20 / M10
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358 19 5211400
Fax +358 19 669765
[email protected]
7-5
EJECTOR PINS
MODEL AH, DIN 1530
PRODUCT GROUP 2101
MAT ERIAL : T O O L ST EEL W S
T HRO UG H HARDENED
HARDNESS: 60 - 62 HRC
HEAD HARDNESS : 45  5 HRC
ORDERING EXAMPLE: EJECTOR PINI AH, d1=8, L=125  PRODUCT NUMBER 2101 0800 125
d1
tol. g6
d2
1.5
1.6
2
2.2
2.5
2.7
3
3.2
3.5
3.7
4
4.2
4.5
4.7
5
5.2
5.5
6
6.2
6.5
7
8
8.2
8.5
9
10
10.2
10.5
11
12
12.2
12.5
14
16
18
20
3
3
4
4
5
5
6
6
7
7
8
8
8
8
10
10
10
12
12
12
12
14
14
14
14
16
16
16
16
18
18
18
22
22
24
26
K
1.5
1.5
2
2
2
2
3
3
3
3
3
3
3
3
3
3
3
5
5
5
5
5
5
5
5
5
5
5
5
7
7
7
7
7
8
8
100
125
160
L
200
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
250
315
400
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358 19 5211400
Fax +358 19 669765
[email protected]
7-6
SUPRA TOOLING
C7 / C12
PRODUCT GROUP 8001/8011
MAX MATERIAL THICKNESS 4 mm
C7 PUNCH: 8001 C7
C12 PUNCH: 8001 C12
C7
C12
ORDER EXAMPLE:
D
7
12
C7 DIE: 8011 C7
C12 DIE: 8011 C12
C7
C12
D
20
30
H
12
12
C12 PUNCH  9,0 mm  PRODUCT GROUP 8001 C12 0900
C12 DIE  9,3 mm  PRODUCT GROUP 8011 C12 0930
C7 AND C12 ARE MANUFACTURED ONLY AS ROUND FORM.
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358 19 5211400
Fax +358 19 669765
[email protected]
9-1
SUPRA TOOLING
PA 8 - 14 - 20 - 35 - 50 - 65 - 80 - 100 - 120
MAX. MATERIAL 4 mm
DIE PA 8 D=25 H=10
DIE PA 14 D=32 H=10
DIE PA 20 D=38 H=10
DIE PA 35 D=60 H=15
DIE PA 50 D=70 H=15
DIE PA 65 D=90 H=15
DIE PA 80 D=110 H=15
DIE PA 100 D=138 H=20
DIE PA 120 D=160 H=20
PUNCH PA 8 D=8
PUNCH PA14 D=14
PUNCH PA20 D=20
PUNCH PA 35 D2=35 D=25
PUNCH PA 100 D2=100 D=62
PUNCH PA 120 D2=120 D=80
STRIPPER PA 8 D=28 D2=16 H=15
STRIPPER PA 20 D=48 D2=30 H =15
STRIPPER PA 100 D=130 D2=100 H=30
STRIPPER PA 120 D=160 D2=120 H=47,5
PRODUCT GROUPS
ROUND
PUNCH
8001 PA8
PA 8
8001 PA14
PA 14
8001 PA20
PA 20
8001 PA35
PA 35
8001 PA50
PA 50
8001 PA65
PA 65
8001 PA80
PA 80
8001 PA100
PA 100
8001 PA120
PA 120
STANDARD FORMS
100
FORM PUNCH
8002 PA8
8002 PA14
8002 PA20
8002 PA35
8002 PA50
8002 PA65
8002 PA80
8002 PA100
8002 PA120
ROUND
DIE
8011 PA8
8011 PA14
8011 PA20
8011 PA35
8011 PA50
8011 PA65
8011 PA80
8011 PA100
8011 PA120
300
400
200
FORM
DIE
8012 PA8
8012 PA14
8012 PA20
8012 PA35
8012 PA50
8012 PA65
8012 PA80
8012 PA100
8012 PA120
ROUND
STRIPPER
8021 PA8
8021 PA14
8021 PA20
8021 PA35
8021 PA50
8021 PA65
8021 PA80
8021 PA100
8021 PA120
FORM
STRIPPER
8022 PA8
8022 PA14
8022 PA20
8022 PA35
8022 PA50
8022 PA65
8022 PA80
8022 PA100
8022 PA120
500
LOCATION GROOVES ON FORMTOOLING
MATERIAL A2 (HWS)
ORDERING EXAMPLE: ROUND PUNCH PA 35 28 
PRODUCT NUMBER 8001 PA35 2800
OVAL DIE PA 50, 45X20  PRODUCT NUMBER 8012 PA50
400 4500 2000
SPECIAL SHAPES ON REQUEST
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358 19 5211400
Fax +358 19 669765
[email protected]
9-2
SUPRA TOOLING
PAE 20 - 35 - 50 - 65 - 80 - 100 - 120
MAX. MATERIAL THICKNESS 10 mm
DIE PAE 20 D=50 H=20
DIE PAE 80 D=110 H=22
DIE PAE 100 D=147 H=30
DIE PAE 120 D=178 H=30
PUNCH PAE 35 D2=35 D=28
PUNCH PAE20 D=20
PRODUCT GROUPS
PAE 20
PAE 35
PAE 50
PAE 65
PAE 80
PAE 100
PAE 120
STRIPPER PAE 20 D=50 D2=30 H=21
STRIPPER PAE 100 D=151,8 D2=100 H=56
ROUND
PUNCH
8001 PAE20
8001 PAE35
8001 PAE50
8001 PAE65
8001 PAE80
FORM
PUNCH
8002 PAE20
8002 PAE35
8002 PAE50
8002 PAE65
8002 PAE80
ROUND
DIE
8011 PAE20
8011 PAE35
8011 PAE50
8011 PAE65
8011 PAE80
FORM
DIE
8012 PAE20
8012 PAE35
8012 PAE50
8012 PAE65
8012 PAE80
ROUND
STRIPPER
8021 PAE20
8021 PAE35
8021 PAE50
8021 PAE65
8021 PAE80
FORM
STRIPPER
8022 PAE20
8022 PAE35
8022 PAE50
8022 PAE65
8022 PAE80
8001 PAE100
8001 PAE120
8002 PAE100
8002 PAE120
8011 PAE100
8011 PAE120
8012 PAE100
8012 PAE120
8021 PAE100
8021 PAE120
8022 PAE100
8022 PAE120
STANDARD FORMS
100
200
300
400
500
LOCATION GROOVES ON FORMTOOLING
MATERIAL A2 (HWS)
ORDERING EXAMPLE: ROUND PUNCH PAE 35 28 
PRODUCT NUMBER 8001 PAE35 2800
OVAL DIE PAE 50, 45X20  PRODUCT NUMBER 8012
PAE50 400 4500 2000
OTHER SPECIAL TOOLING ON REQUEST
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358 19 5211400
Fax +358 19 669765
[email protected]
9-3
GUIDING VALUES FOR DIE CLEARANCE
THE CLEARANCE VALUES IN THE TABLE ARE GUIDING VALUES.
SPECIAL DEMANDS MUST BE NOTICED CASE-BY-CASE.
CLEARANCE VALUES
Material
Thickness
mm
0,50
1,00
1,50
2,00
2,50
3,00
3,50
4,00
4,50
5,00
5,50
6,00
6,50
7,00
7,50
8,00
8,50
9,00
9,50
10,00
Fe37
mm
0,10
0,15
0,20
0,30
0,40
0,45
0,50
0,60
0,70
0,75
0,80
0,90
1,00
1,05
1,10
1,20
1,30
1,40
1,45
1,50
Stainless
steel
mm
0,15
0,20
0,25
0,35
0,45
0,50
0,55
0,65
0,75
0,80
0,85
0,95
1,05
1,10
1,15
1,25
1,35
1,45
1,50
1,55
Aluminium
soft
mm
0,05
0,10
0,15
0,25
0,35
0,40
0,45
0,55
0,65
0,70
0,75
0,85
0,95
1,00
1,05
1,15
1,25
1,35
1,40
1,45
Copper
soft
mm
0,05
0,10
0,15
0,25
0,35
0,40
0,45
0,55
0,65
0,70
0,75
0,85
0,95
1,00
1,05
1,15
1,25
1,35
1,40
1,45
Oy Suomen EDM Ab
Yrittäjänkatu 20
www.suomenedm.fi
Tel. +358 19 5211400
Fax +358 19 669765
[email protected]
9-4

product catalogue

Transcription

Similar documents

CampUs WELs