catalogo serranda in alluminio

CATALOGO SERRANDA
IN ALLUMINIO
DESCRIZIONE
La porta serranda a rullo è realizzata su misura
con stecche a incasso e doppia parete in
alluminio estruso di altezza 40,75 mm.
Serve per chiudere casse, porte di carico o
d’accesso in ogni tipologia di veicoli, in
sostituzione delle porte
a battenti.
È consegnata in elementi separati, pronti per
l’installazione a cura del costruttore:
• 1 serranda assemblata
• 1 coppia di binari in alluminio, pronti all’installazione
• 1 avvolgitore in tensione
La finitura standard è RAL 7035,a richiesta è possibile fare qualsiasi colore.
1-VITE INOX TH 8 X 100
2-PIASTRA PER ALU30
3-VITE INOXTH6 X 16
4-RONDELLA INOX
5-BINARIO STANDARD
6-GUARNIZIONE SCORREVOLE DOPPIO BORDO NERO
7-PUNTALE SINISTRA NERO PER STECCA
8-GUARNIZIONE
9-GIUNTO FRA STECCHE
10-STECCA
11-PUNTALE NERO PER STECCA
12-FERMA SERRANDA CON CINGHIA
13-FORCELLA DI BLOCCAGGIO
14-ANELLI DI AVVOLGIMENTO PROGRESSIVO
15-AVVOLGITORE
16-GRAFFA PER TUBO DA 62
17-RONDELLA INOX
18-TRAVERSA IN ACCIAIO PER RUOTA 80
19-TRAVERSA IN PLASTICA PER RUOTA 80
20-DADO
21-RONDELLA
22-RONDELLA
23-DADO
24-SUPPORTO AVVOLGITORE
25-VITE
26-PIASTRINA NERA
27-ASSIEME LEVA
28-PUNTALE PER STECCA FINALE
29-STECCA FINALE
30-TUBO ROTONDO ALLUMINIO
31-CONTROPIASTRA GRIGIO PER CILINDRO ROTONDO
32-GUARNIZIONE INF.NERA
33-BACCHETTA
34-TAPPO NERO
35-BOCCHETTA PER CHIUSURA BARRA
36-BOCCHETTA BARRA DI BLOCCO
37-SERRATURA
38-PUNTALE PER STECCA FINALE
39-RONDELLA
40-DADO
41-PULSANTE
42-DOPPIA MANIGLIA
43-PUNTALE PER STECCA FINALE
44-CILINDRO
45-MOLLA DI COMPRESIONE
46-RONDELLA
47-VITE 6X40
48-STECCA FINALE
49-GUARNIZINE INF.NERA
50-PIASTRINA ROTONDA PER DOPPIA MANIGLIA
51-VITE INOX
52-FISSAGGIO ASTA
53-RONDELLA
54-ASTA
55-VITE INOX
56-MOLLA DI FLESSIONE
57-VITE INOX
58-PUNTALE DESTRA PER STECCA FINALE
59-DADO
60-COPERTURA
61-FERMO IN ALTO COMPLETO
62-BOCCHETTA DI CHIUSURA
63-TAPPO DI CHIUSURA PER STECCA FINALE
CATALOUGUE ALUMINUM SHUTTER
DESCRIPTION
The door roller shutter is made to measure
with a stick built and extruded aluminum
double wall height 40,75mm.
The door shutter need to shut down the boxes,
Doors loading or access in all types of vehicles,
In replacing the door swing.
The door shutter is delivered is separate in
elements, ready for installation by the
manufacturer:




1 shutter assembled
1 couple of tracks in aluminum
1 roller voltage
1 bag accessories
The standard finish is ral 7035, on reguest we can make any color.
TYPE OF GUIDES
IMPORTANT FORMULAS
HI=HO+L
HP=HO-100mm
L=TO BE DETERMINED ON THE BASIS OF HO THE TABLE BELOW.
FOUR SEALS ENSURE THE SEALES
SEAL GUIDES
WARNING:THERE ARE OTHER POSSIBILITES BASED ON LOCATION A,B
SEAL UPPER
O C WHELL.
FOR THE OPERATION OF DOOR DAMPER,IT IS RECOMMEND THAT THE
DOOR C.
SEAL UNDER
SEAL BETWEEN THE STICKS
CLOSURE WITH BAR
CLOSURE WITH DOUBLE HANDLE
1-SCREW
29- CUE FINAL
57-SCREW
2-PLATE
30- ROUND ALUMINUM TUBE
58- CUE TIP FOR FINAL
3-SCREW
31- COUNTER
59- STAINLESS STEEL BRAKE NUT M6
4- STEEL WASHER
32- SEAL LOWER
60- COVER
5-BINARY
33- WAND
61- CATCH UP COMPLETE
6-SEAL SLIDING DOUBLE BLACK BORDER
34- CAP BLACK
62- INTAKE CLOSING
7-TIP BLACK LEFT TO STICK
35- INTAKE FOR LOCKING BAR
63- SEALING CAP
8-SEAL UPPER BLACK FOR SLAT
36- INTAKE FOR BAR LOCK
9-JOINT BETWEEN GREY STICKS
37- LOCK
10-SLAT
38- CUE TIP FOR FINA
11-TIP BLACK FOR SLAT
39- STEEL WASHER
12-FREEZE SHUTTER WITH BELT
40- STAINLESS STEEL BRAKE NUT M5
13-FORK LOCK
41- BUTTON
14-RING OF WINDING
42- DOUBLE HANDLE
15-WINDER
43- CUE TIP FOR FINAL
16-BRACE FOR PIPE
44- CYLINDER
17-STEEL WASHER
45- SPRING
18-CROSS STEEL FOR WHEEL
46- STEEL WASHER
19-CROSS IN PLASTIC WHEEL
47-SCREW
20-STAINLESS STEEL BRAKE NUT M8
48- CUE FINAL
21-WHEEL
49- SEAL LOWER
22-STEEL WASHER
50- PLATE ROUND
23- STAINLESS STEEL BRAKE NUT M8
51-SCREW
24- REEL HOLDER
52- FIXING ROD
25- SCREW
53- STEEL WASHER
26- PLATE BLACK
54- AUCTION
27- LEVER ASSEMBLY
55-SCREW
28- CUE TIP FOR FINAL
56- SPRING
ASSEMBLY INSTRUCTIONS
1 - Check the position of the rails (5) and the plate ( 2 ) in the vehicle.
2 - Attach the rails (5) on the uprights of the opening.
3 - Securely fasten the plates ( 2 ) on the same mast, after the track.
4 - Position the self-adhesive (8) behind the lintel , between the tracks, after having adjusted. Must be in a position to
rub the damper during the maneuvers of opening and closing.
5 - According inside the enclosure or vehicle, place the roller (15) in the media (24) fixed on the plates. Please note: the label must always
on the right as seen from the inside , and the braces ( 16) towards the inside , lock the supports with the screws (25).
6 - Position the damper on the rails by sliding slightly . Proceed with caution , so as not to damage it.
7 - Turn the rollers (21 ) on the plate with the bolt ( 1 ) the cross ( 18:19 ) and nut (20 ) to verify the correct alignment of the part
exterior of the wheel with the inner side of the track, so that the damper does not hit against the entrance of the track during maneuvers.
8 - Connect the shutter winder with straps (12) and clips ( 16).
9 - After this operation (it is important that it is later), or remove the forks (13 ) from the end of the winder in order to release the tension.
10 - Position the locking system .
11 - Spray a bit ' of silicone into the tracks .
ILLUSTRATIVE PHOTOS