3b. submersible grinder pumps

www.cranepumps.com
GENERAL INFORMATION
CROSS-REFERENCE
SPECIFICATIONS
INSTALLATION DRAWINGS
3B. SUBMERSIBLE GRINDER PUMPS
PUMP SERIES:
SGVF & SGVH (2HP)
SGV (3, 5 & 7.5HP)
OGVF & OGVH (2HP) Omni Grind
OGVF-AU & OGVH-AU (2HP - Automatic) Omni Grind
OGVF2022M (2HP) Flanged Upgrade Core
OGP (2HP) Omni Grind Plus
OGP-AU (2HP - Automatic) Omni Grind Plus
OGP2022CO (2HP) Upgrade Core - Fixed Discharge
OGP2022AUE (2HP) Upgrade Core - 1.25" NPT
SECTION 3B
A
PAGE
6/15
DATE
A Crane Co. Company
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
www.cranepumps.com
This page intentionally left blank
SECTION 3B
B
PAGE
B
DATE
9/08
A Crane Co. Company
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Cross-Reference Chart
Engineered Pump
www.cranepumps.com
Submersible Grinder Pumps
*Previous
Models
MODEL
*Previous
Models
P/N
Current Models
*Previous
Models
MODEL
P/N
MODEL
P/N
MODEL
P/N
PAGE NO.
SGV2002L
084794EV
SGV2002L
105239
SGVF2002L
110614
3-6
SGV201
75871
SGV2022L
084794
SGV2022L
105234
SGVF2022L
110609
3-6
SGV202
67578
SGV2062L
084795
SGV2062L
105235
SGVF2062L
110610
3-6
SGV203
67579
SGV2032L
084796
SGV2032L
105236
SGVF2032L
110611
3-6
SGV204
67580
SGV2042L
084797
SGV2042L
105237
SGVF2042L
110612
3-6
SGV2052L
088860
SGV2052L
105238
SGVF2052L
110613
3-6
SGVH2002L
110620
3-6
SGVH2022L
110615
3-6
SGVH2062L
110616
3-6
SGVH2032L
110617
3-6
SGVH2042L
110618
3-6
SGVH2052L
110619
3-6
SGV3072L
111608
7-9
SGV300
71001
SGV3002L
084798
SGV301
71002
SGV3022L
084799
SGV302
71003
SGV3062L
084800
SGV3062L
111612
7-9
SGV303
71007
SGV3032L
084801
SGV3032L
111609
7-9
SGV304
71008
SGV3042L
084802
SGV3042L
111610
7-9
SGV3052L
088861
SGV3052L
111611
7-9
SGV500
71004
SGV5002L
084803
SGV5002L
115657
7-9
SGV501
71005
SGV5022L
084804
SGV5022L
115658
7-9
SGV502
71006
SGV5062L
084805
SGV5062L
111619
7-9
SGV503
71009
SGV5032L
084806
SGV5032L
111616
7-9
SGV504
71010
SGV5042L
084807
SGV5042L
111617
7-9
SGV5052L
088862
SGV5052L
111618
7-9
SGV753
71011
SGV7532L
084808
SGV7532L
111613
7-9
SGV754
71012
SGV7542L
084809
SGV7542L
111614
7-9
SGV7552L
088863
SGV7552L
111615
7-9
OGP2022L
115328
10 - 12
OGP2022AUF
116662
13 - 15
OGP2022AUE
115329
13 - 15
OGP2022C
119425
15A - 15C
Previous Models are Discontinued. Consult Factory for current replacement if not shown.
SECTION 3B
C
PAGE
02/05
DATE
A Crane Co. Company
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Cross-Reference Chart
Engineered Pump
www.cranepumps.com
Submersible Grinder Pumps
*Previous
Models
MODEL
*Previous
Models
P/N
MODEL
P/N
*Previous
Models
MODEL
P/N
SG200
65850
SG2002L
084789
SG201
65851
SG2022L
084790
SG202
65852
SG2062L
084791
SG203
65853
SG2032L
084792
SG204
65854
SG2042L
084793
Current Models
MODEL
P/N
PAGE NO.
OGVF2022L
110651
16 - 19
OGVH2022L
110649
16 - 19
OGVF2022AUF
110652
20 - 23
OGVF2022AUE
116892
20 - 23
OGVH2022AUF
110650
20 - 23
OGVH2022AUE
116896
20 - 23
OGVF2022M
113750
24 - 26
Previous Models are Discontinued. Consult Factory for current replacement if not shown.
SECTION 3B
D
PAGE
DATE
4/06
A Crane Co. Company
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Series SGVF & SGVH
Recessed Vortex
www.cranepumps.com
Submersible Grinder Pumps
Specifications:
DISCHARGE ................................... 1¼” NPT, Vertical, Bolt-on Flange
LIQUID TEMPERATURE 160°F (71°C)Intermittent
VOLUTE ............................................ Cast Iron ASTM A-48, Class 30.
MOTOR HOUSING ............................ Cast Iron ASTM A-48, Class 30.
SEAL PLATE .................................... Cast Iron ASTM A-48, Class 30.
IMPELLER: Design ...................... 12 Vane,Vortex, With Pump Out Vanes
On Back Side. Dynamically Balanced,
ISO G6.3.
Material ..................... Cast Iron
SHREDDING RING ........................... Hardened 440C Stainless Steel
Rockwell® C-55.
CUTTER ............................................ Hardened 440CStainless Steel,
Rockwell® C-55.
SHAFT .............................................. 416 Stainless Steel
SQUARE RINGS ............................... Buna-N
HARDWARE ...................................... 300 Series Stainless Steel
PAINT ................................................ Air Dry Enamel.
SEAL:
Design ....................... Tandem Mechanical, Oil Filled Reservoir.
Material ...................... Rotating Faces - Carbon
Stationary Faces - Ceramic
Elastomer - Buna-N
Hardware -300 Series Stainless
CORD ENTRY ................................... 30 ft. (9.1 m) Std. Cord. Custom Molded
Quick Connect, for Sealing and Strain
Relief
CORD ................................................. CSA/UL Approved 12/4 Type SOW.
UPPER BEARING:
Design ....................... Single Row, Ball, Oil Lubricated
Load .......................... Radial
INTERMEDIATE BEARING:
Design ....................... Single Row, Ball, Oil Lubricated
Load .......................... Radial & Thrust
LOWER BEARING:
Design ....................... Sleeve, Oil Lubrication:
Load ........................... Radial
MOTOR:
Design ....................... NEMA L-Single Phase, (SGVF2022L,
SGVH2022L, SGVF2002L or SGVH2002L,
includes overload protection in the
motor). NEMA B-Three Phase Torque
Curve. Oil-Filled, Squirrel Cage Induction
Insulation ................ Class B.
SINGLE PHASE ................................. Capacitor Start/Capacitor Run. Includes
overload protection in the motor. Requires
Barnes® Starter or Control Panel which
Includes Capacitors, or Capacitor pack.
THREE PHASE .................................. Dual Voltage 240/480; Requires Overload
Protection to be Included in control panel.
OPTIONAL EQUIPMENT................... Seal Material, Impeller Trims, Cord Length.
Moisture Sensors, Moveable Fitting, Leg Kit
P/N: 108339.
RECOMMENDED:
Accessories..................Break Away Fitting (BAF)
Check Valve
Control Panel
Seal Kit PN ..................113299
Service Kit PN ..............115946
Series: SGVF & SGVH
2HP, 3450RPM, 60Hz
High-Flow and High Head
CSA 108 - File No. LR16567
UL 778
NRTL\C
Models SGVF2002L and SGFH2002L
are NOT UL or CSA listed
Sample Specifications: Section 3 Page 8.
DESCRIPTION:
THE GRINDER PUMP IS DESIGNED TO
REDUCE DOMESTIC, COMMERCIAL,
INSTITUTIONAL AND LIGHT INDUSTRIAL
SEWAGE TO A FINELY GROUND SLURRY.
SECTION 3B
1
PAGE
8/16
DATE
A Crane Co. Company
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Series SGVF & SGVH
Recessed Vortex
www.cranepumps.com
Submersible Grinder Pumps
inches
(mm)
MODEL NO
PART NO
HP
VOLT
PH/Hz
RPM
(Nom)
NEMA
START
CODE
FULL
LOAD
AMPS
LOCKED
ROTOR
AMPS
CORD
SIZE
CORD
TYPE
CORD O.D.
± .02 (.5)
in (mm)
SGVF2002L*
110614
2
200
1 / 60
3450
F
17.0
53.0
SGVF2022L
110609
2
240
1 / 60
3450
H
15.0
53.8
12/4
SOW
.67 (17)
12/4
SOW.
SGVF2062L
110610
2
200
3 / 60
3450
J
11.0
42.0
12/4
.67 (17)
SOW
.67 (17)
HIGH-FLOW
SGVF2032L
110611
2
240
3 / 60
3450
J
9.0
36.0
12/4
SOW
.67 (17)
SGVF2042L
110612
2
480
3 / 60
3450
J
4.0
18.0
12/4
SOW
.67 (17)
SGVF2052L
110613
2
600
3 / 60
3450
J
3.2
14.4
12/4
SOW
.67 (17)
SGVH2002L*
110620
2
200
1 / 60
3450
F
17.0
53.0
12/4
SOW
.67 (17)
SGVH2022L
110615
2
240
1 / 60
3450
H
15.0
53.8
12/4
SOW
.67 (17)
SGVH2062L
110616
2
200
3 / 60
3450
J
11.0
42.0
12/4
SOW
.67 (17)
SGVH2032L
110617
2
240
3 / 60
3450
J
9.0
36.0
12/4
SOW
.67 (17)
SGVH2042L
110618
2
480
3 / 60
3450
J
4.0
18.0
12/4
SOW
.67 (17)
SGVH2052L
110619
2
600
3 / 60
3450
J
3.2
14.4
12/4
SOW
.67 (17)
HIGH-HEAD
Optional - Temperature sensor cord for all models is 14/3 SOW, 0.55 (14mm) ± .02 (.51mm) O.D.
(Not used on SGVF2022L, SGVH2022L, SGVF2002L or SGVH2002L).
Optional - Moisture and Temperature sensor cord for all models is 18/5 SOW, 0.49 (12.4mm) ± .02 (.51mm) O.D., replaces Temperature sensor cord.
(*) This pump is NOT UL or CSA listed
IMPORTANT !
1.) PUMP MAY BE OPERATED “DRY” FOR EXTENDED PERIODS WITHOUT DAMAGE TO MOTOR AND/OR SEALS.
2.) INSTALLATIONS SUCH AS DECORATIVE FOUNTAINS OR WATER FEATURES PROVIDED FOR VISUAL ENJOYMENT MUST BE INSTALLED IN ACCORDANCE
WITH THE NATIONAL ELECTRIC CODE ANSI/NFPA 70 AND/OR THE AUTHORITY HAVING JURISDICTION. THIS PUMP IS NOT INTENDED FOR USE IN
SWIMMING POOLS, RECREATIONAL WATER PARKS, OR INSTALLATIONS IN WHICH HUMAN CONTACT WITH PUMPED MEDIA IS A COMMON OCCURRENCE.
SECTION 3B
2
PAGE
8/16
DATE
A Crane Co. Company
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Series SGVF
www.cranepumps.com
Performance Curve
2HP, 3450RPM, 60Hz, High-Flow
Submersible Grinder Pumps
inches
(mm)
Testing is performed with water, specific gravity 1.0 @ 68º F @ (20ºC), other fluids may vary performance
SECTION 3B
3
PAGE
7/09
DATE
A Crane Co. Company
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Series SGVH
Performance Curve
2HP, 3450RPM, 60Hz, High-Head
www.cranepumps.com
Submersible Grinder Pumps
inches
(mm)
Testing is performed with water, specific gravity 1.0 @ 68º F @ (20ºC), other fluids may vary performance
SECTION 3B
4
PAGE
11/03
DATE
A Crane Co. Company
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Series SGV
Recessed Vortex
www.cranepumps.com
Submersible Grinder Pumps
Specifications:
DISCHARGE ................................... 2” NPT, Vertical
LIQUID TEMPERATURE ................ 104°F (40°C) Continuous
VOLUTE ............................................ Cast Iron ASTM A-48, Class 30.
MOTOR HOUSING ............................ Cast Iron ASTM A-48, Class 30.
SEAL PLATE .................................... Cast Iron ASTM A-48, Class 30.
IMPELLER: Design ...................... 12 Vane,Vortex, With Pump Out Vanes
On Back Side. Dynamically Balanced,
ISO G6.3.
Material ..................... Cast Iron
SHREDDING RING ........................... Hardened 440C Stainless Steel
Rockwell® C-55.
CUTTER ............................................ Hardened 440CStainless Steel,
Rockwell® C-55.
SHAFT .............................................. 416 Stainless Steel
SQUARE RINGS ............................... Buna-N
HARDWARE ...................................... 300 Series Stainless Steel
PAINT ................................................ Air Dry Enamel.
SEAL:
Design ....................... Tandem Mechanical, Oil Filled Reservoir.
Material ...................... Rotating Faces - Carbon
Stationary Faces - Ceramic
Elastomer - Buna-N
Hardware -300 Series Stainless
CORD ENTRY:
SGV5002L & SGV5022L .................... 30 ft. (9m) Std. Cord. Pressure
Grommet for Sealing and Strain Relief.
All Other Models ................................. 30 ft. (9m) Std. Cord. Custom Molded
Quick Connect for For Sealing and Strain
Relief
CORD ................................................. CSA/UL Approved 10/4, 6/4, 8/4 Type SOW.
UPPER BEARING:
Design ....................... Single Row, Ball, Oil Lubricated
Load .......................... Radial
INTERMEDIATE BEARING:
Design ....................... Single Row, Ball, Oil Lubricated
Load .......................... Radial & Thrust
LOWER BEARING:
Design ....................... Sleeve, Oil Lubrication:
Load ........................... Radial
MOTOR:
Design ....................... NEMA L-Single Phase, NEMA B-Three
Phase Torque Curve. Oil-Filled, Squirrel
Cage Induction.
Insulation ... ................ Class F.
SINGLE PHASE ................................. Capacitor Start/Capacitor Run. Requires
Overload Protection to be Included In control
panel, Requires Barnes® Starter or Control
Panel which Includes Capacitors, or Capacitor
pack.
THREE PHASE .................................. Dual Voltage 240/480; Requires Overload
Protection to be Included in control panel.
OPTIONAL EQUIPMENT................... Seal Material, Impeller Trims, Cord Length.
Moisture Sensors, Moveable Fitting
SGV5002L & SGV5022L ONLY
Series: SGV
3, 5, 7.5 HP,
3450RPM, 60Hz
CSA 108 - File No. LR16567
UL 778
NRTL\C
Sample Specifications: Section 3 Page 9.
RECOMMENDED:
Accessories..................Break Away Fitting (BAF)
Check Valve
Control Panel
Seal Kit PN ..................085223
Service Kit PN ..............115771
DESCRIPTION:
THE GRINDER PUMP IS DESIGNED TO
REDUCE DOMESTIC, COMMERCIAL,
INSTITUTIONAL AND LIGHT INDUSTRIAL
SEWAGE TO A FINELY GROUND SLURRY.
SECTION 3B
5
PAGE
1/12
DATE
A Crane Co. Company
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Series SGV
Recessed Vortex
www.cranepumps.com
Submersible Grinder Pumps
inches
(mm)
MODEL NO
PART NO
HP
VOLT/PH
Hz
RPM
(Nom)
NEMA
START
CODE
FULL
LOAD
AMPS
LOCKED
ROTOR
AMPS
CORD
SIZE
CORD
TYPE
CORD O.D.
± .02 (.5)
in (mm)
SGV3072L
111608
3
200/240/1
60
3450
G
25.2/21.7
86/75
10/4
SOW
.75 (19)
SGV3062L
111612
3
200/3
60
3450
J
17.0
65.0
10/4
SOW
.75 (19)
SGV3032L
111609
3
240/3
60
3450
K
14.5
62.0
10/4
SOW
.75 (19)
SGV3042L
111610
3
480/3
60
3450
K
7.2
31.0
10/4
SOW
.75 (19)
SGV3052L
111611
3
600/3
60
3450
J
5.6
22.6
10/4
SOW
.75 (19)
SGV5002L
115657
5
200/1
60
3450
F
42.0
134.0
6/4
SOW
1.03 (26)
SGV5022L
115658
5
240/1
60
3450
H
39.0
136.0
8/4
SOW
.93 (24)
SGV5062L
111619
5
200/3
60
3450
K
25.0
122.0
10/4
SOW
.75 (19)
SGV5032L
111616
5
240/3
60
3450
L
21.9
120.0
10/4
SOW
.75 (19)
SGV5042L
111617
5
480/3
60
3450
L
11.0
60.0
10/4
SOW
.75 (19)
SGV5052L
111618
5
600/3
60
3450
L
8.8
46.0
10/4
SOW
.75 (19)
SGV7532L
111613
7.5
240/3
60
3450
J
22.3
136.0
10/4
SOW
.75 (19)
SGV7542L
111614
7.5
480/3
60
3450
J
11.2
68.0
10/4
SOW
.75 (19)
SGV7552L
111615
7.5
600/3
60
3450
G
8.2
45.0
10/4
SOW
.75 (19)
Temperature sensor cord for SGV5002L & SGV5022L is 14/2 SOW, 0.55 (14mm) ± .02 (.51mm) O.D.
Temperature sensor cord for all other models is 14/3 SOW, 0.55 (14mm) ± .02 (.51mm) O.D.
Optional - Moisture and Temperature sensor cord for all models is 18/5 SOW, 0.47 (12mm) ± .02 (.51mm) O.D., replaces Temperature sensor cord.
IMPORTANT !
1.) PUMP MAY BE OPERATED “DRY” FOR EXTENDED PERIODS WITHOUT DAMAGE TO MOTOR AND/OR SEALS.
2.) INSTALLATIONS SUCH AS DECORATIVE FOUNTAINS OR WATER FEATURES PROVIDED FOR VISUAL ENJOYMENT MUST BE INSTALLED IN ACCORDANCE
WITH THE NATIONAL ELECTRIC CODE ANSI/NFPA 70 AND/OR THE AUTHORITY HAVING JURISDICTION. THIS PUMP IS NOT INTENDED FOR USE IN
SWIMMING POOLS, RECREATIONAL WATER PARKS, OR INSTALLATIONS IN WHICH HUMAN CONTACT WITH PUMPED MEDIA IS A COMMON OCCURRENCE.
SECTION 3B
6
PAGE
12/15
DATE
A Crane Co. Company
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Series SGV
www.cranepumps.com
Performance Curve
3, 5, 7.5 HP, 3450RPM, 60Hz
Submersible Grinder Pumps
inches
(mm)
Testing is performed with water, specific gravity 1.0 @ 68º F @ (20ºC), other fluids may vary performance
SECTION 3B
7
PAGE
1/14
DATE
A Crane Co. Company
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Series OGVF & OGVH
Recessed Vortex
www.cranepumps.com
Submersible Grinder Pumps
Specifications:
Series: OGVF & OGVH
2HP, 3450RPM, 60Hz
High-Flow and High Head
DISCHARGE ...............................1¼” NPT, Vertical, Bolt-on Flange
LIQUID TEMPERATURE .............160°F (71°C)Intermittent
VOLUTE ......................................Cast Iron ASTM A-48, Class 30
MOTOR HOUSING ......................Cast Iron ASTM A-48, Class 30
SEAL PLATE ..............................Cast Iron ASTM A-48, Class 30
IMPELLER: Design ....................12 Vane,Vortex, With Pump Out Vanes
On Back Side. Dynamically Balanced,
ISO G6.3.
Material ..................Cast Iron
SHREDDING RING .....................Hardened 440C Stainless Steel
Rockwell® C-55.
CUTTER ......................................Hardened 440C Stainless Steel,
Rockwell® C-55.
SHAFT ........................................416 Stainless Steel
SQUARE RINGS .........................Buna-N
HARDWARE ................................300 Series Stainless Steel
PAINT ..........................................Air Dry Enamel.
SEAL:
Design ....................Single Mechanical
Material ...................Rotating Faces - Silicon-Carbide
Stationary Faces - Silicon-Carbide
Elastomer - Buna-N
Hardware - 300 Series Stainless
CORD ENTRY ..............................30 ft. (9.1 m) Std, Cord. Custom Molded
Quick Connect, for Sealing and Strain
Relief
CORD
Manual ....................CSA/UL Approved 12/3 Type SOW
UPPER BEARING:
Design ....................Single Row, Ball, Oil Lubricated
Load .......................Radial
LOWER BEARING:
Design ....................Single Row, Ball, Oil Lubrication:
Load ........................Radial & Thrust
MOTOR:
Design ....................NEMA L-Single Phase Torque Curve.
Oil-Filled, Squirrel Cage Induction.
Insulation ...............Class F.
SINGLE PHASE ...........................Capacitor Start/Capacitor Run.
OPTIONAL EQUIPMENT.............Seal Material, Impeller Trims, Cord Length,
Moveable Fitting
CSA 108 - File No. LR16567
UL 778
RECOMMENDED:
Accessories .............Break Away Fitting (BAF)
Check Valve
Control Panel
Seal Kit PN .............108303
NRTL\C
Sample Specifications: Section 3 Page 11.
DESCRIPTION:
THE GRINDER PUMP IS DESIGNED TO
REDUCE DOMESTIC, COMMERCIAL,
INSTITUTIONAL AND LIGHT INDUSTRIAL
SEWAGE TO A FINELY GROUND SLURRY.
SECTION 3B
8
PAGE
DATE
8/16
A Crane Co. Company
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Series OGVF & OGVH
Recessed Vortex
www.cranepumps.com
Submersible Grinder Pumps
inches
(mm)
MODEL NO
PART NO
HP
VOLT
PH/Hz
RPM
(Nom)
NEMA
START
CODE
FULL
LOAD
AMPS
LOCKED
ROTOR
AMPS
CORD
SIZE
CORD
TYPE
CORD O.D.
± .02 (.5)
in (mm)
110651
2
240
1 / 60
3450
H
15.0
53.8
12/3
SOW
.61 (15.5)
110649
2
240
1 / 60
3450
H
15.0
53.8
12/3
SOW
.61 (15.5)
HIGH-FLOW
OGVF2022L
HIGH-HEAD
OGVH2022L
IMPORTANT !
1.) PUMP MAY BE OPERATED “DRY” FOR EXTENDED PERIODS WITHOUT DAMAGE TO MOTOR AND/OR SEALS.
2.) INSTALLATIONS SUCH AS DECORATIVE FOUNTAINS OR WATER FEATURES PROVIDED FOR VISUAL ENJOYMENT MUST BE INSTALLED IN ACCORDANCE
WITH THE NATIONAL ELECTRIC CODE ANSI/NFPA 70 AND/OR THE AUTHORITY HAVING JURISDICTION. THIS PUMP IS NOT INTENDED FOR USE IN
SWIMMING POOLS, RECREATIONAL WATER PARKS, OR INSTALLATIONS IN WHICH HUMAN CONTACT WITH PUMPED MEDIA IS A COMMON OCCURRENCE.
SECTION 3B
9
PAGE
8/16
DATE
A Crane Co. Company
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Series OGVF
Performance Curve
2HP, 3450RPM, 60Hz, High-Flow
www.cranepumps.com
Submersible Grinder Pumps
inches
(mm)
Testing is performed with water, specific gravity 1.0 @ 68º F @ (20ºC), other fluids may vary performance
SECTION 3B
10
PAGE
7/09
DATE
A Crane Co. Company
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Series OGVH
www.cranepumps.com
Performance Curve
2HP, 3450RPM, 60Hz, High-Head
Submersible Grinder Pumps
inches
(mm)
Testing is performed with water, specific gravity 1.0 @ 68º F @ (20ºC), other fluids may vary performance
SECTION 3B
11
PAGE
11/03
DATE
A Crane Co. Company
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Series OGVF-AU & OGVH-AU
Recessed Vortex
with Level Control
www.cranepumps.com
Submersible Grinder Pumps
Specifications:
Series: OGVF-AU & OGVH-AU
2HP, 3450RPM, 60Hz
with Level Control
High-Flow and High Head
CSA 108 - File No. LR16567
UL 778
"AUF" series pumps NOT UL or
CSA listed
NRTL\C
Sample Specifications: Section 3 Page 11.
DISCHARGE ...............................1¼” NPT, Vertical, Bolt-on Flange
LIQUID TEMPERATURE .............160°F (71°C)Intermittent
VOLUTE ......................................Cast Iron ASTM A-48, Class 30
MOTOR HOUSING ......................Cast Iron ASTM A-48, Class 30
SEAL PLATE ..............................Cast Iron ASTM A-48, Class 30
IMPELLER: Design ....................12 Vane,Vortex, With Pump Out Vanes
On Back Side. Dynamically Balanced,
ISO G6.3.
Material ..................Cast Iron
SHREDDING RING .....................Hardened 440C Stainless Steel
Rockwell® C-55.
CUTTER ......................................Hardened 440C Stainless Steel,
Rockwell® C-55.
SHAFT ........................................416 Stainless Steel
SQUARE RINGS .........................Buna-N
HARDWARE ................................300 Series Stainless Steel
PAINT ..........................................Air Dry Enamel.
SEAL:
Design ....................Single Mechanical
Material ...................Rotating Faces - Silicon-Carbide
Stationary Faces - Silicon-Carbide
Elastomer - Buna-N
Hardware -300 Series Stainless
CORD ENTRY ..............................30 ft. (9.1 m) Std, Cord. Custom Molded
Quick Connect, for Sealing and Strain Relief
CORD
Automatic ................CSA/UL Approved 12/5 Type SOW
UPPER BEARING:
Design ....................Single Row, Ball, Oil Lubricated
Load .......................Radial
LOWER BEARING:
Design ....................Single Row, Ball, Oil Lubrication:
Load ........................Radial & Thrust
MOTOR:
Design ....................NEMA L-Single Phase Torque Curve.
Oil-Filled, Squirrel Cage Induction.
Insulation ...............Class F.
SINGLE PHASE ...........................Capacitor Start/Capacitor Run.
LEVEL CONTROL:
AU Series ...............On/Off & Alarm Wide Angle, PVC
Mechanical, Normally Open, Integral to
pump. Custom molded quick connect for
sealing and strain relief
AUE Series .............SOLD SEPARATELY (See Accessory
Section C page 36A) Model ESPS-150,
Environmentally sealed pressure switch
with CPVC housing, Buna diaphragm,
Custom molded quick connect for sealing
and strain relief
OPTIONAL EQUIPMENT.............Seal Material, Impeller Trims, Cord Length,
Moveable Fitting
DESCRIPTION:
THE GRINDER PUMP IS DESIGNED TO
REDUCE DOMESTIC, COMMERCIAL,
INSTITUTIONAL AND LIGHT INDUSTRIAL
SEWAGE TO A FINELY GROUND SLURRY.
RECOMMENDED:
Accessories .............Break Away Fitting (BAF)
Check Valve
Control Panel
Seal Kit PN .............108303
SECTION 3B
12
PAGE
DATE
8/16
A Crane Co. Company
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Series OGVF-AU & OGVH-AU
Recessed Vortex
with Level Control
www.cranepumps.com
Submersible Grinder Pumps
AUF
AUE*
MODEL NO
PART NO
HP
VOLT
PH/Hz
RPM
NEMA
(Nom) START
CODE
FULL
LOAD
AMPS
LOCKED
ROTOR
AMPS
CORD
SIZE
CORD
TYPE
CORD O.D.
± .02 (.5)
in (mm)
HIGH-FLOW
OGVF2022AUF
110652
2
240
1 / 60
3450
H
15.0
53.8
12/5
SOW
.71 (18)
OGVF2022AUE*
116892
2
240
1 / 60
3450
H
15.0
53.8
12/5
SOW
.71 (18)
HIGH-HEAD
OGVH2022AUF
110650
2
240
1 / 60
3450
H
15.0
53.8
12/5
SOW
.71 (18)
OGVH2022AUE*
116896
2
240
1 / 60
3450
H
15.0
53.8
12/5
SOW
.71 (18)
(*) ESPS Level Control Sold Separately, See Accessory Section C page 36A & B.
IMPORTANT !
1.) PUMP MAY BE OPERATED “DRY” FOR EXTENDED PERIODS WITHOUT DAMAGE TO MOTOR AND/OR SEALS.
2.) INSTALLATIONS SUCH AS DECORATIVE FOUNTAINS OR WATER FEATURES PROVIDED FOR VISUAL ENJOYMENT MUST BE INSTALLED IN ACCORDANCE
WITH THE NATIONAL ELECTRIC CODE ANSI/NFPA 70 AND/OR THE AUTHORITY HAVING JURISDICTION. THIS PUMP IS NOT INTENDED FOR USE IN
SWIMMING POOLS, RECREATIONAL WATER PARKS, OR INSTALLATIONS IN WHICH HUMAN CONTACT WITH PUMPED MEDIA IS A COMMON OCCURRENCE.
SECTION 3B
13
PAGE
8/16
DATE
A Crane Co. Company
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Series OGVF-AU
Performance Curve
2HP, 3450RPM, 60Hz, High-Flow
www.cranepumps.com
Submersible Grinder Pumps
inches
(mm)
Testing is performed with water, specific gravity 1.0 @ 68º F @ (20ºC), other fluids may vary performance
SECTION 3B
14
PAGE
7/09
DATE
A Crane Co. Company
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Series OGVH-AU
www.cranepumps.com
Performance Curve
2HP, 3450RPM, 60Hz, High-Head
Submersible Grinder Pumps
inches
(mm)
Testing is performed with water, specific gravity 1.0 @ 68º F @ (20ºC), other fluids may vary performance
SECTION 3B
15
PAGE
11/03
DATE
A Crane Co. Company
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Series OGVF2022M
Flanged Upgrade Core
Recessed Vortex
www.cranepumps.com
Submersible Grinder Pumps
Specifications:
DISCHARGE ...............................1¼” Horizontal Flange
SUCTION .....................................3" ANSI Flange
LIQUID TEMPERATURE .............160°F (71°C)Intermittent
VOLUTE ......................................Cast Iron ASTM A-48, Class 30
MOTOR HOUSING ......................Cast Iron ASTM A-48, Class 30
SEAL PLATE ..............................Cast Iron ASTM A-48, Class 30
IMPELLER: Design ....................12 Vane,Vortex, With Pump Out Vanes
On Back Side. Dynamically Balanced,
ISO G6.3.
Material ..................Cast Iron
SHREDDING RING .....................Hardened 440C Stainless Steel
Rockwell® C-55.
CUTTER ......................................Hardened 440C Stainless Steel,
Rockwell® C-55.
SHAFT ........................................416 Stainless Steel
SQUARE RINGS .........................Buna-N
HARDWARE ................................300 Series Stainless Steel
PAINT ..........................................Air Dry Enamel.
SEAL:
Design ....................Single Mechanical
Material ...................Rotating Faces - Silicon-Carbide
Stationary Faces - Silicon-Carbide
Elastomer - Buna-N
Hardware - 300 Series Stainless
CORD ENTRY ..............................30 ft. (9.1 m) Std, Cord. Custom Molded
Quick Connect, for Sealing and Strain Relief
CORD
Automatic ................CSA/UL Approved 12/3 Type SOW
UPPER BEARING:
Design ....................Single Row, Ball, Oil Lubricated
Load .......................Radial
LOWER BEARING:
Design ....................Single Row, Ball, Oil Lubrication:
Load ........................Radial & Thrust
MOTOR:
Design ....................NEMA L-Single Phase Torque Curve.
Oil-Filled, Squirrel Cage Induction.
Insulation ...............Class F.
SINGLE PHASE ...........................Capacitor Start/Capacitor Run.
OPTIONAL EQUIPMENT.............Seal Material, Impeller Trims, Cord Length
Series: OGVF2022M
2HP, 3450RPM, 60Hz
Flanged Upgrade Core
RECOMMENDED:
Accessories .............Break Away Fitting (BAF)
Check Valve
Control Panel
Seal Kit PN .............108303
DESCRIPTION:
THE GRINDER PUMP IS DESIGNED TO
REDUCE DOMESTIC, COMMERCIAL,
INSTITUTIONAL AND LIGHT INDUSTRIAL
SEWAGE TO A FINELY GROUND SLURRY.
SECTION 3B
16
PAGE
DATE
6/15
A Crane Co. Company
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Series OGVF2022M
Flanged Upgrade Core
Recessed Vortex
www.cranepumps.com
Submersible Grinder Pumps
inches
(mm)
MODEL NO
PART NO
HP
VOLT
PH/Hz
RPM
(Nom)
NEMA
START
CODE
FULL
LOAD
AMPS
LOCKED
ROTOR
AMPS
CORD
SIZE
CORD
TYPE
CORD O.D.
± .02 (.5)
in (mm)
113750
2
240
1 / 60
3450
H
15.0
53.8
12/3
SOW
.61 (15.5)
OGVF2022M
KITS for Existing pumps:
OGVF - P/N: 116426
OGVH - P/N: 116424
IMPORTANT !
1.) PUMP MAY BE OPERATED “DRY” FOR EXTENDED PERIODS WITHOUT DAMAGE TO MOTOR AND/OR SEALS.
2.) INSTALLATIONS SUCH AS DECORATIVE FOUNTAINS OR WATER FEATURES PROVIDED FOR VISUAL ENJOYMENT MUST BE INSTALLED IN ACCORDANCE
WITH THE NATIONAL ELECTRIC CODE ANSI/NFPA 70 AND/OR THE AUTHORITY HAVING JURISDICTION. THIS PUMP IS NOT INTENDED FOR USE IN
SWIMMING POOLS, RECREATIONAL WATER PARKS, OR INSTALLATIONS IN WHICH HUMAN CONTACT WITH PUMPED MEDIA IS A COMMON OCCURRENCE.
SECTION 3B
17
PAGE
DATE
6/15
A Crane Co. Company
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Series OGVF2022M
Performance Curve
2HP, 3450RPM, 60Hz, High-Flow
www.cranepumps.com
Submersible Grinder Pumps
inches
(mm)
Testing is performed with water, specific gravity 1.0 @ 68º F @ (20ºC), other fluids may vary performance
SECTION 3B
18
PAGE
DATE
7/09
A Crane Co. Company
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
www.cranepumps.com
Submersible Grinder Pumps
This page intentionally left blank
SECTION 3B
19
PAGE
DATE
A Crane Co. Company
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Series OGP
Recessed Vortex
www.cranepumps.com
Submersible Grinder Pumps
Specifications:
Series: OGP
2HP, 3450RPM, 60Hz
This product may be covered by one or more of
the following patents and other patent(s) pending:
US Patent 7,357,341
CSA 108 - File No. LR16567
UL 778
*3 Phase Models are CSA Listed ONLY*
Sample Specifications: Section 3 Page 10.
DISCHARGE ...............................1¼” NPT, Vertical, Bolt-on Flange
LIQUID TEMPERATURE .............104°F (40°C) Continuous
VOLUTE ......................................Cast Iron ASTM A-48, Class 30
MOTOR HOUSING ......................Cast Iron ASTM A-48, Class 30
SEAL PLATE ..............................Cast Iron ASTM A-48, Class 30
IMPELLERS: Design....................12 Vane,Vortex, With Pump Out Vanes
On Back Side. Dynamically Balanced,
ISO G6.3.
Material ..................85-5-5-5 Bronze
IMPELLER SPACER....................300 Series Stainless Steel
SHREDDING RING .....................Hardened 440C Stainless Steel
Rockwell® C-55.
CUTTER ......................................Hardened 440CStainless Steel,
Rockwell® C-55.
SHAFT ........................................416 Stainless Steel
SQUARE RINGS .........................Buna-N
HARDWARE ................................300 Series Stainless Steel
PAINT ..........................................Air Dry Enamel.
SEAL:
Design ....................Single Mechanical
Material ...................Rotating Faces - Silicon-Carbide
Stationary Faces - Silicon-Carbide
Elastomer - Buna-N
Hardware -300 Series Stainless
CORD ENTRY ..............................30 ft. (9.1 m) Std. Cord. Custom Molded
Quick Connect, for Sealing and Strain
Relief
CORD
Manual ....................CSA/UL Approved, 12/4 Type SOW
UPPER BEARING:
Design ....................Single Row, Angular contact Ball
Lubrication ..............Oil
Load .......................Radial & Thrust
LOWER BEARING:
Design ....................Single Row, Angular contact Ball
Lubrication .............Oil
Load ........................Radial & Thrust
MOTOR:
Design ....................NEMA L-Single Phase Torque Curve,
Oil-Filled, Squirrel Cage Induction
(includes overload protection in the
motor), NEMA B three phase torque curve.
Insulation ...............Class F
SINGLE PHASE ...........................Capacitor Start/Capacitor Run.
THREE PHASE ............................Tri-Voltage 200/240-480, requires
overload protection to be included in
control panel.
OPTIONAL EQUIPMENT.............Cord Length, Moveable Fitting
DESCRIPTION:
THE GRINDER PUMP IS DESIGNED TO
REDUCE DOMESTIC SEWAGE TO A FINELY
GROUND SLURRY.
RECOMMENDED:
Accessories .............Break Away Fitting (BAF)
Check Valve
Control Panel
Seal Kit PN .............116664
Service Kit PN..........116665
SECTION 3B
20
PAGE
8/16
DATE
A Crane Co. Company
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Series OGP
Recessed Vortex
www.cranepumps.com
Submersible Grinder Pumps
inches
(mm)
MODEL NO
PART NO
HP
VOLT
PH/Hz
RPM
(Nom)
NEMA
START
CODE
FULL
LOAD
AMPS
LOCKED
ROTOR
AMPS
CORD
SIZE
CORD
TYPE
CORD O.D.
± .02 (.5)
in (mm)
OGP2022L
115328
2
240
1 / 60
3450
H
16.5
53.8
12/3
SOW
.61 (15.5)
OGP2062L
134925
2
200
3 / 60
3450
L
10.8
52.7
12/4
SOW
.67 (17.0)
OGP2032L
135034
2
240
3 / 60
3450
L
8.9
43.9
12/4
SOW
.67 (17.0)
OGP2042L
135035
2
480
3 / 60
3450
L
4.5
22.0
12/4
SOW
.67 (17.0)
FOR 3 PHASE MODELS: TEMPERATURE SENSOR CORD IS 14/3 SOW, 0.55 (14MM) ± .02 (.51MM) O.D.
IMPORTANT !
1.) PUMP MAY BE OPERATED “DRY” FOR EXTENDED PERIODS WITHOUT DAMAGE TO MOTOR AND/OR SEALS.
2.) INSTALLATIONS SUCH AS DECORATIVE FOUNTAINS OR WATER FEATURES PROVIDED FOR VISUAL ENJOYMENT MUST BE INSTALLED IN ACCORDANCE
WITH THE NATIONAL ELECTRIC CODE ANSI/NFPA 70 AND/OR THE AUTHORITY HAVING JURISDICTION. THIS PUMP IS NOT INTENDED FOR USE IN
SWIMMING POOLS, RECREATIONAL WATER PARKS, OR INSTALLATIONS IN WHICH HUMAN CONTACT WITH PUMPED MEDIA IS A COMMON OCCURRENCE.
SECTION 3B
21
PAGE
8/16
DATE
A Crane Co. Company
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Series OGP
Performance Curve
2HP, 3450RPM, 60Hz, High-Flow
www.cranepumps.com
Submersible Grinder Pumps
inches
(mm)
Testing is performed with water, specific gravity 1.0 @ 68º F @ (20ºC), other fluids may vary performance
SECTION 3B
22
PAGE
DATE
3/13
A Crane Co. Company
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Series OGP-AU
Recessed Vortex
with Level Control
www.cranepumps.com
Submersible Grinder Pumps
Specifications:
DISCHARGE ...............................1¼” NPT, Vertical, Bolt-on Flange
LIQUID TEMPERATURE .............104°F (40°C) Continuous
VOLUTE ......................................Cast Iron ASTM A-48, Class 30
MOTOR HOUSING ......................Cast Iron ASTM A-48, Class 30
SEAL PLATE ..............................Cast Iron ASTM A-48, Class 30
IMPELLERS: Design....................12 Vane,Vortex, With Pump Out Vanes
On Back Side. Dynamically Balanced,
ISO G6.3.
Material ..................85-5-5-5 Bronze
IMPELLER SPACER....................300 Series Stainless Steel
SHREDDING RING .....................Hardened 440C Stainless Steel
Rockwell® C-55.
CUTTER ......................................Hardened 440CStainless Steel,
Rockwell® C-55.
SHAFT ........................................416 Stainless Steel
SQUARE RINGS .........................Buna-N
HARDWARE ................................300 Series Stainless Steel
PAINT ..........................................Air Dry Enamel.
SEAL:
Design ....................Single Mechanical
Material ...................Rotating Faces - Silicon-Carbide
Stationary Faces - Silicon-Carbide
Elastomer - Buna-N
Hardware -300 Series Stainless
CORD ENTRY ..............................30 ft. (9.1 m) Std. Cord. Custom Molded
Quick Connect, for Sealing and Strain
Relief
CORD
Automatic ................CSA/UL Approved 12/5 Type SOW
UPPER BEARING:
Design ....................Single Row, Angular contact Ball
Lubrication ..............Oil
Load .......................Radial & Thrust
LOWER BEARING:
Design ....................Single Row, Angular contact Ball
Lubrication .............Oil
Load ........................Radial & Thrust
MOTOR:
Design ....................NEMA L-Single Phase Torque Curve,
Oil-Filled, Squirrel Cage Induction
Insulation ...............Class F
SINGLE PHASE ...........................Capacitor Start/Capacitor Run.
LEVEL CONTROL:
AUF Series..............On/Off & Alarm wide angle, PVC
Mechanical normally open, Integral to
pump. Custom molded quick connect for
sealing and strain relief
AUE Series .............SOLD SEPARATELY (See Accessory
Section C page 36A) Model ESPS-150,
Environmentally sealed pressure switch
with CPVC housing, Buna diaphragm,
Custom molded quick connect for sealing
and strain relief
OPTIONAL EQUIPMENT.............Cord Length, Moveable Fitting
RECOMMENDED:
Accessories .............Break Away Fitting (BAF)
Check Valve
Control Panel
Seal Kit PN .............116664
Service Kit PN..........116665
Series: OGP-AU
2HP, 3450RPM, 60Hz
with Level Control
This product may be covered by one or more of
the following patents and other patent(s) pending:
US Patent 7,357,341
CSA 108 - File No. LR16567
UL 778
"AUF" series pumps NOT UL
or CSA listed
Sample Specifications: Section 3 Page 10.
DESCRIPTION:
THE GRINDER PUMP IS DESIGNED TO
REDUCE DOMESTIC SEWAGE TO A FINELY
GROUND SLURRY.
SECTION 3B
23
PAGE
8/16
DATE
A Crane Co. Company
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Series OGP-AU
Recessed Vortex
with Level Control
www.cranepumps.com
Submersible Grinder Pumps
OGP2022AUF
inches
(mm)
OGP2022AUE*
MODEL NO
PART NO
HP
VOLT
PH/Hz
RPM
(Nom)
NEMA
START
CODE
FULL
LOAD
AMPS
LOCKED
ROTOR
AMPS
CORD
SIZE
CORD
TYPE
CORD O.D.
± .02 (.5)
in (mm)
OGP2022AUF
116663
2
240
1 / 60
3450
H
16.5
53.8
12/5
SOW
.71 (18)
OGP2022AUE*
115329-M
2
240
1 / 60
3450
H
16.5
53.8
12/5
SOW
.71 (18)
(*) ESPS Level Control Sold Separately, See Accessory Section C page 36A & B.
IMPORTANT !
1.) PUMP MAY BE OPERATED “DRY” FOR EXTENDED PERIODS WITHOUT DAMAGE TO MOTOR AND/OR SEALS.
2.) INSTALLATIONS SUCH AS DECORATIVE FOUNTAINS OR WATER FEATURES PROVIDED FOR VISUAL ENJOYMENT MUST BE INSTALLED IN ACCORDANCE
WITH THE NATIONAL ELECTRIC CODE ANSI/NFPA 70 AND/OR THE AUTHORITY HAVING JURISDICTION. THIS PUMP IS NOT INTENDED FOR USE IN
SWIMMING POOLS, RECREATIONAL WATER PARKS, OR INSTALLATIONS IN WHICH HUMAN CONTACT WITH PUMPED MEDIA IS A COMMON OCCURRENCE.
SECTION 3B
24
PAGE
DATE
8/16
A Crane Co. Company
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Series OGP-AU
www.cranepumps.com
Performance Curve
2HP, 3450RPM, 60Hz, High-Flow
Submersible Grinder Pumps
inches
(mm)
Testing is performed with water, specific gravity 1.0 @ 68º F @ (20ºC), other fluids may vary performance
SECTION 3B
25
PAGE
11/03
DATE
A Crane Co. Company
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Model OGP2022CO
Fixed Discharge Upgrade Core
www.cranepumps.com
Submersible Grinder Pumps
Specifications:
Series: OGP2022CO
2HP, 3450RPM, 60Hz
Upgrade Core with Level
Control
This product may be covered by one or more of
the following patents and other patent(s) pending:
US Patent 7,357,341 & US Patent 7,578,657
PUMP IS CSA 108 - File No.
LR16567 (UL 778 E81854)
DESCRIPTION:
THE GRINDER PUMP IS DESIGNED TO
REDUCE DOMESTIC SEWAGE TO A FINELY
GROUND SLURRY.
DISCHARGE ...............................1¼” Tubing, Vertical, Bolt-on Flange
LIQUID TEMPERATURE .............104°F (40°C) Continuous
VOLUTE ......................................Cast Iron ASTM A-48, Class 30
MOTOR HOUSING ......................Cast Iron ASTM A-48, Class 30
SEAL PLATE ..............................Cast Iron ASTM A-48, Class 30
IMPELLERS: Design....................12 Vane,Vortex, With Pump Out Vanes
On Back Side. Dynamically Balanced,
ISO G6.3.
Material ..................85-5-5-5 Bronze
IMPELLER SPACER....................300 Series Stainless Steel
SHREDDING RING .....................Hardened 440C Stainless Steel
Rockwell® C-55.
CUTTER ......................................Hardened 440CStainless Steel,
Rockwell® C-55.
SHAFT ........................................416 Stainless Steel
SQUARE RINGS .........................Buna-N
HARDWARE ................................300 Series Stainless Steel
PAINT ..........................................Air Dry Enamel.
SEAL:
Design ....................Single Mechanical
Material ...................Rotating Faces - Silicon-Carbide
Stationary Faces - Silicon-Carbide
Elastomer - Buna-N
Hardware -300 Series Stainless
CORD ENTRY ..............................15 ft. (4.5m) Std. Cord. Custom Molded
Quick Connect, for Sealing and Strain
Relief (EQD Optional)
CORD
Automatic ................CSA/UL Approved 12/5 Type SOW
UPPER BEARING:
Design ....................Single Row, Angular contact Ball
Lubrication ..............Oil
Load .......................Radial & Thrust
LOWER BEARING:
Design ....................Single Row, Angular contact Ball
Lubrication .............Oil
Load ........................Radial & Thrust
MOTOR:
Design ....................NEMA L-Single Phase Torque Curve,
Oil-Filled, Squirrel Cage Induction
Insulation ...............Class F
SINGLE PHASE ...........................Capacitor Start/Capacitor Run
SUPPORT POD ...........................Engineered Polyamide Pod,
Stainless Hardware and Polypropylene
Rope
LEVEL CONTROL .......................Model ESPS-150, Environmentally sealed
pressure switch with CPVC housing,
Buna diaphragm, Custom molded quick
connect for sealing and strain relief
CHECK VALVE
Body ........................Integrated PA Composite
Seat.........................ASTM C836
Flap .........................Fiber Reinforced Buna
RECOMMENDED
Seal Kit PN..............116664
Service Kit PN .........116665
SECTION 3B
26
PAGE
6/15
DATE
A Crane Co. Company
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Model OGP2022CO
Fixed Discharge Upgrade Core
www.cranepumps.com
Submersible Grinder Pumps
inches
(mm)
OPTIONAL INDOOR REMOTE ALARM LIGHT
PART NO.
PLATE COLOR
130849B
ALMOND
130849W
WHITE
130849S
STAINLESS
(Ordered Separately)
MODEL NO
PART NO
HP
VOLT/PH
Hz
RPM
(Nom)
NEMA
START
CODE
FULL LOCKED
LOAD ROTOR
AMPS
AMPS
CORD
SIZE
CORD
TYPE
CORD O.D.
± .02 (.5)
in (mm)
OPTIONAL
EQD
OGP2022CO
131717
2
240/1
60
3450
H
16.5
53.8
12/5 - 15'
SOW
.71 (18)
None
OGP2022CO
131717XC
2
240/1
60
3450
H
16.5
53.8
12/5 - 30'
SOW
.71 (18)
None
OGP2022CO
131717E
2
240/1
60
3450
H
16.5
53.8
12/5 - 15'
SOW
.71 (18)
2000 Series
OGP2022CO
131717EXC
2
240/1
60
3450
H
16.5
53.8
12/5 - 30'
SOW
.71 (18)
2000 Series
OGP2022CO
131717T
2
240/1
60
3450
H
16.5
53.8
12/5 - 15'
SOW
.71 (18)
Extreme Series
OGP2022CO
131717TXC
2
240/1
60
3450
H
16.5
53.8
12/5 - 30'
SOW
.71 (18)
Extreme Series
Optional Circuit Breakers - Ordered Separately
PART NO.
DESCRIPTION
113291B
20 AMP, GE THQP Snap in Breaker
105476
20 AMP, DIN Rail Breaker
IMPORTANT !
1.) PUMP MAY BE OPERATED “DRY” FOR EXTENDED PERIODS WITHOUT DAMAGE TO MOTOR AND/OR SEALS.
2.) INSTALLATIONS SUCH AS DECORATIVE FOUNTAINS OR WATER FEATURES PROVIDED FOR VISUAL ENJOYMENT MUST BE INSTALLED IN ACCORDANCE
WITH THE NATIONAL ELECTRIC CODE ANSI/NFPA 70 AND/OR THE AUTHORITY HAVING JURISDICTION. THIS PUMP IS NOT INTENDED FOR USE IN
SWIMMING POOLS, RECREATIONAL WATER PARKS, OR INSTALLATIONS IN WHICH HUMAN CONTACT WITH PUMPED MEDIA IS A COMMON OCCURRENCE.
SECTION 3B
27
PAGE
DATE
6/15
A Crane Co. Company
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Model OGP2022CO
Fixed Discharge Upgrade Core
Performance Curve 2HP, 3450RPM, 60Hz
www.cranepumps.com
Submersible Grinder Pumps
inches
(mm)
Performance curve includes impact of integral anti-siphon and check valve.
Testing is performed with water, specific gravity 1.0 @ 68º F @ (20ºC), other fluids may vary performance
SECTION 3B
28
PAGE
6/15
DATE
A Crane Co. Company
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Model OGP2022AUE
1.25" NPT Upgrade Core
www.cranepumps.com
Submersible Grinder Pumps
Specifications:
DISCHARGE ...............................1¼” NPT
LIQUID TEMPERATURE .............104°F (40°C) Continuous
VOLUTE ......................................Cast Iron ASTM A-48, Class 30
MOTOR HOUSING ......................Cast Iron ASTM A-48, Class 30
SEAL PLATE ..............................Cast Iron ASTM A-48, Class 30
IMPELLERS: Design....................12 Vane,Vortex, With Pump Out Vanes
On Back Side. Dynamically Balanced,
ISO G6.3.
Material ..................85-5-5-5 Bronze
IMPELLER SPACER....................300 Series Stainless Steel
SHREDDING RING .....................Hardened 440C Stainless Steel
Rockwell® C-55.
CUTTER ......................................Hardened 440CStainless Steel,
Rockwell® C-55.
SHAFT ........................................416 Stainless Steel
SQUARE RINGS .........................Buna-N
HARDWARE ................................300 Series Stainless Steel
PAINT ..........................................Air Dry Enamel.
SEAL:
Design ....................Single Mechanical
Material ...................Rotating Faces - Silicon-Carbide
Stationary Faces - Silicon-Carbide
Elastomer - Buna-N
Hardware -300 Series Stainless
CORD ENTRY ..............................15ft. (3.0m) Std. Cord. Custom Molded
Quick Connect, for Sealing and Strain
Relief (EQD Optional)
CORD
Automatic ................CSA/UL Approved 12/5 Type SOW
UPPER BEARING:
Design ....................Single Row, Angular contact Ball
Lubrication ..............Oil
Load .......................Radial & Thrust
LOWER BEARING:
Design ....................Single Row, Angular contact Ball
Lubrication .............Oil
Load ........................Radial & Thrust
MOTOR:
Design ....................NEMA L-Single Phase Torque Curve,
Oil-Filled, Squirrel Cage Induction
Insulation ...............Class F
SINGLE PHASE ...........................Capacitor Start/Capacitor Run
SUPPORT PLATE .......................Painted Cast Iron with rubber feet,
Stainless Steel Hardware
LEVEL CONTROL .......................Model ESPS-150, Environmentally sealed
pressure switch with CPVC housing,
Buna diaphragm, Custom molded quick
connect for sealing and strain relief
CHECK/ANTI-SIPHON VALVE
Body ........................Cast Iron ASTM A-48, Class 30
Seat.........................Bronze ASTM C836
Flap .........................Fiber Reinforced Buna
Series: OGP2022AUE
2HP, 3450RPM, 60Hz
Upgrade Core with Level
Control
PUMP IS CSA 108 - File No.
LR16567 (UL 778 E81854)
DESCRIPTION:
THE GRINDER PUMP IS DESIGNED TO
REDUCE DOMESTIC SEWAGE TO A FINELY
GROUND SLURRY.
SECTION 3B
29
PAGE
8/16
DATE
A Crane Co. Company
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Model OGP2022AUE
1.25" NPT Upgrade Core
www.cranepumps.com
Submersible Grinder Pumps
inches
(mm)
MODEL NO
PART NO
HP VOLT/PH Hz
RPM NEMA FULL LOCKED
(Nom) START LOAD ROTOR
CODE AMPS AMPS
CORD
SIZE
CORD
TYPE
CORD O.D.
± .02 (.5)
in (mm)
OPTIONAL
EQD
OGP2022AUE
131281
2
240/1
60
3450
H
16.5
53.8
12/5 - 15'
SOW
.71 (18)
No
OGP2022AUE
131281XC
2
240/1
60
3450
H
16.5
53.8
12/5 - 30'
SOW
.71 (18)
No
OGP2022AUE
131281E
2
240/1
60
3450
H
16.5
53.8
12/5 - 15'
SOW
.71 (18)
2000 Series
OGP2022AUE
131281EXC
2
240/1
60
3450
H
16.5
53.8
12/5 - 30'
SOW
.71 (18)
2000 Series
OGP2022AUE
131281T
2
240/1
60
3450
H
16.5
53.8
12/5 - 30'
SOW
.71 (18)
Extreme Series
OGP2022AUE
131281TXC
2
240/1
60
3450
H
16.5
53.8
12/5 - 30'
SOW
.71 (18)
Extreme Series
Optional Circuit Breakers - Ordered Separately
PART NO.
DESCRIPTION
OPTIONAL INDOOR REMOTE ALARM LIGHT
113291B
20 AMP, GE THQP Snap in Breaker
105476
20 AMP, DIN Rail Breaker
PART NO.
PLATE COLOR
130849B
ALMOND
130849W
WHITE
130849S
STAINLESS
(Ordered Separately)
IMPORTANT !
1.) PUMP MAY BE OPERATED “DRY” FOR EXTENDED PERIODS WITHOUT DAMAGE TO MOTOR AND/OR SEALS.
2.) INSTALLATIONS SUCH AS DECORATIVE FOUNTAINS OR WATER FEATURES PROVIDED FOR VISUAL ENJOYMENT MUST BE INSTALLED IN ACCORDANCE
WITH THE NATIONAL ELECTRIC CODE ANSI/NFPA 70 AND/OR THE AUTHORITY HAVING JURISDICTION. THIS PUMP IS NOT INTENDED FOR USE IN
SWIMMING POOLS, RECREATIONAL WATER PARKS, OR INSTALLATIONS IN WHICH HUMAN CONTACT WITH PUMPED MEDIA IS A COMMON OCCURRENCE.
SECTION 3B
30
PAGE
DATE
8/16
A Crane Co. Company
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
Model OGP2022AUE
www.cranepumps.com
1.25" NPT Upgrade Core
Performance Curve 2HP, 3450RPM, 60Hz
Submersible Grinder Pumps
inches
(mm)
Performance curve includes impact of integral anti-siphon and check valve.
Testing is performed with water, specific gravity 1.0 @ 68º F @ (20ºC), other fluids may vary performance
SECTION 3B
31
PAGE
6/15
DATE
A Crane Co. Company
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598
www.cranepumps.com
Submersible Grinder Pumps
This page intentionally left blank
SECTION 3B
32
PAGE
DATE
A Crane Co. Company
USA: (937) 778-8947 • Canada: (905) 457-6223 • International: (937) 615-3598