Application - iMetal.net

Transcription

Table of
Contents
Click On Any of the Sections Below to Jump to That Page
Section
Page
Section
Page
General Information
Metal to Wood
Fastener Design ...............................................................3-4
Woodgrip Fasteners ................................................... 38-40
Washer and Fastener Head Styles................................... 5
EVERGRIP® Stainless Fasteners ......................................41
Structural Performance ..................................................... 6
Stainless Aluminum Panel Woodgrip ........................... 42
Woodgrip Capped Fasteners .................................... 43-45
Self-Drilling Fasteners
Impax™ Performance Drill Screws ................................... 7
Panelmaster® Metal to Wood Fastening System
Impax™ Heavy Metal Thickness
Structural Drill Screws .................................................. 8
Panelmaster® Tool & Collated
Belted Fasteners ........................................................... 46
Impax™ Sealer Drill Screws ............................................... 9
Impax™ 1/4" Drill Screws ............................................. 10-11
Standing Seam Roof Attachment
Impax™ Utility Self-Drill .....................................................12
Standing Seam Panel Clips ........................................ 47-51
410 Stainless ...................................................................... 13
Bearing Plates.................................................................... 52
Flat Head Utility Self-Drill ................................................ 14
Clip Fasteners .............................................................. 53-54
Alloy Capped Fasteners
Attachment Solutions
ZAC® Impax™ 5/16" HWH Alloy Capped ........................ 15
AceClamp® - for Standing Seam Roofs ........................ 55
ZAC® Impax™ 3/8" HWH Alloy Capped
(for metal to metal) ................................................. 16-17
SOL-R - solar attachment for
exposed fastener metal roofs .................................... 56
ZAC® Impax™ 3/8" HWH Alloy Capped
(for metal to metal and insulated
panel to metal) .............................................................. 18
Blind Rivets and Grommets
MAC Impax Stainless Capped Self-Drill ................... 19
Blind Rivet Tools ..........................................................61-62
ZAC® Self-Tapping Fasteners .......................................... 20
Grommet Fasteners.......................................................... 63
™
™
Blind Rivets ...................................................................57-60
Prisma™ ............................................................................... 21
Self-Tapping Fasteners
Closure, Sealants, Flashings and
Venting Products
Carbon Steel – Type A, AB, B ....................................22-23
WG-7™ Closure................................................................... 64
Stainless Steel – Type A, AB, B .................................24-25
Pipe Flashing ............................................................... 65-66
ProfileVent® ...................................................................67-68
Architectural Fasteners (304SS Fasteners)
Ventco™ Ridge Cap Anchor Clip ..................................... 69
SX Stainless Self-Drill .................................................26-27
Butyl Tape .......................................................................... 70
irius® SX Stainless Self-Drill.......................................28-29
Hannoband® BG1 Joint Sealant Tape ............................ 71
SX TORX Self-Drill .....................................................30-31
Novaflex® Metal Roof Sealant ................................... 72-73
TW-S Stainless Self-Tapping
(cladding fastener) ....................................................... 32
Tools and Tool Accessories
SLA Stainless Self-Drill (Aluminum
composite to aluminum) ............................................. 33
Installation Screw Guns and
drive sockets ..................................................................74
SA6/TDA (Panel fabrication fasteners).......................... 34
Panelmaster Tool Kit ........................................................ 46
AP Rivet (Cladding panels to
aluminum or steel) ....................................................... 35
Blind Rivet Tools ..........................................................61-62
®
TU-S Blind Fastener (HPL cladding
panel attachment) ........................................................ 36
GAZ Design Elements ...................................................... 37
1
SFS intec, Inc. | WEATHER GARD Product Group | 1-800-234-4533
iMetal.net - Phone: 267-983-1017 - www.iMetal.net
©2012 SFS intec, Inc.
There's More to See....
Disclosure Statement
The fasteners shown are standard products.
Fastener data shown herein is subject to change or
Many related, non-standard items are not
correction for typographical error without notice. All
shown, but are available and will be priced on
test data and ultimate values shown in this catalog are
application. We offer a complete selection of
the result of laboratory testing. Specific job conditions
fasteners, closures and accessories. Please
should be considered and appropriate safety factors
contact us with specific requirements.
applied when specifying fasteners. In actual applications,
A Word About the
Specification of Fasteners
Proper fastener selection takes into account where
and how the fasteners are installed. Factors that must
be considered include: materials being attached,
environmental factors, installation conditions, and safety
issues. Because product specifications, applications,
and interpretations may differ, specifiers and purchasers
must make their own product evaluation to be assured of
suitability for the intended use.
proper installation techniques must be used to assure
adequate performance of the fastener. Assistance and
recommendations are available by contacting your SFS
intec, Inc. sales or customer service professional.
Final selection of fasteners or accessories for use is
ultimately the decision of the purchaser. While SFS
intec, Inc. may assist by providing data and information
for comparison, it makes no suggestions or warranties
pertaining to the suitability of its products for any
particular applicaion.
Galvalume ® is a registered trademark of BIEC
International, Inc. TORX® is a registered trademark of
Textron Inc.
Highlighted Text with a Red Box is a Link to Our Online Shopping Cart
2
Fastener Design
Fastener Design
Threaded fasteners for roofing and siding systems are
ZAC design fasteners are available with a 5/16" and
available in a wide range of materials, designs, and
3/8" capped hex washer head in Impax™ self-drilling
coatings. When specifying your fastener, be sure to
fasteners, Woodgrip™ sheet-to-wood fasteners and
choose one that has a performance life equaling or
self-tapping screws.
exceeding the life of the proposed project.
Fastener Materials
MAC™ 300 Series Stainless Capped Head Self-Drilling
Fasteners
Common Fastener compositions:
• Zinc plated and paint coated carbon steel
• Alloy capped fasteners with zinc-aluminum,
stainless steel, and nylon capped head designs
• Stainless Steel: 300 Series austenitic stainless steel
MAC 300 Series Stainless capped head design combines
• Stainless Steel: 400 Series martensitic stainless steel
the corrosion resistance of stainless steel and a
• Bi-metal: stainless head and threaded shank with a
hardened steel fastener for self-drilling installation. MAC
joint welded hardened carbon steel drill or sharp point
Coated Corrosion-Resistant Fasteners
SFS intec offers various coating systems such as
electroplating, mechanical plating, and VistaCoat ®
Premium System. Zinc serves as a sacrificial coating to
fasteners are available with a 5/16" capped hex washer
head in Impax self-drilling fasteners and with a 1/4" hex
washer head in Woodgrip fasteners.
Prisma™ Nylon Head Self-Drilling
and Self-Tapping Fasteners
provide cut-edge plating protection.
Metal Alloy Capped Fasteners
ZAC ® Zinc Aluminum Capped Head
ZAC design fasteners provide the corrosion resistance
Prisma design fasteners combine the corrosion
resistance of a nylon-molded head with a hardened
steel fastener for self-drilling and self-tapping
installation. The nylon head is formulated with the color
built in. It naturally resists fading and will never rust like
steel headed fasteners. Prisma design fasteners are
of a zinc-aluminum alloy capped head on a hardened
available with 3/8" and 7/16" hex washer heads in self-
steel fastener for self-drilling or self-tapping installation.
drillers, Woodgrip metal-to-wood fasteners, and self-
ZAC is the original capped zinc-aluminum head fastener
tapping AB fasteners.
and is used in more metal buildings than any other
capped fastener.
3
Fastener Design
Stainless Steel Fasteners
A commonly held belief that stainless steel will not rust
or corrode is not necessarily accurate. Stainless steel
• Poor corrosion resistance compared
to austenitic stainless
is a generic term covering over 200 different types
• Magnetic
of alloys that, to varying degrees, corrode less than
• Plated to improve corrosion resistance
carbon steel. It is important that a specifier be aware of
the panel and project performance expectations when
specifying stainless steel fasteners.
Several types of stainless steel are used for fasteners.
300 Series Stainless/Austenitic
(like carbon steel fasteners)
• Martensitic stainless is not considered
suitable for panel fasteners
Bi-Metal Fasteners
• 18-8 stainless alloy with 18% chromium and 8% nickel
• Best known grades are 304 and 316, both work
hardened in the thread-rolling process to manufacture
a self-tapping fastener capable of tapping threads
into steel
• Can be manufactured as a self-drilling, bi-metal
fastener by incorporating a heat-treated hardened
carbon steel drill point joint welded to the austenitic
stainless fastener
SX Fastener: Austenitic Stainless Self-Drilling Fasteners
SX design fasteners combine the corrosion resistance
of an austenitic 300 series stainless head and threaded
shank with a hardened carbon steel point for self-
• Nonmagnetic
• Provides excellent corrosion resistance compared to
martensitic 410SS fasteners and plated steel fasteners
• Austenitic stainless steel is considered the only type
of stainless steel for panel fasteners
410 Series Stainless/Martensitic
drilling installation. These bi-metal fasteners install
like carbon steel fasteners and provide the corrosion
resistance of 18-8 300 series austenitic stainless. SX
fasteners are true stainless steel self-drilling fasteners.
When selecting a stainless steel fastener for any
application where minimizing or virtually eliminating
• Stainless alloy with 11.5% to 13.5% chromium
corrosion is the goal, a specifier should strongly
• Can be heat treated to provide hardness to
consider the dramatically greater benefits of 300 series
manufacture as self-tapping or self-drilling
fasteners (when hardened, the part has less
corrosion resistance)
over 400 series stainless steel fasteners. The richer
chemical composition and SX welded drill point make
300 series stainless steel fasteners more costly, but the
corrosion resistance benefits are far superior.
4
Washer Styles
Washer Styles
Washer design contributes to the weather seal of a
Control Seal
fastener. SFS offers several washer options based upon
the type of fastener and the application requirements.
Bonded Washer
• EPDM rubber captured under the stamped “dome”
• Available on all #9 and #12 XG Woodgrip drill screws
• Reinforced domed shoulder distributes clamp load
• EPDM rubber bonded to metal
• EPDM sealant compressed in three key areas
• Metal washers are available in galvanized
• Weather tight seal even if fastener is driven
steel, aluminum, and stainless steel
in on an angle*
• Bonded washers offer a low-profile appearance
panel and fastener head
Sealer Cupped Hex Washer Head
Fastener Head Styles
SFS offers a wide variety of fastener head styles
designed to meet your project and fastener
POSITIVE reduced 00%
• Provides positive weather seal between
requirements. Each head style will provide proper
panel attachment and desired finish appearance.
Available fastener head styles are:
• irius® drive, low profile
• EPDM rubber captured under integral
• HWH (hex washer head)
cupped hex head washer
• Cupped hex washer head sealer
• Cupped washer head prevents overdriving
• EPDM washer and cupped head offers
• Metal-alloy capped cupped:
an excellent weather seal
HWH ZAC or HWH MAC
• EPDM is protected from UV rays
• Pancake head
by cupped washer head
• Low Profile TORX®
• Low Profile Wafer Head
*Proper installation techniques should always be employed.
5
File Name: FD00.5_ZAC_HeadStyle.eps
NEGATIVE reduced 00%
Created by: EWB-12/10/02
Revised: MPD-00/00/02
Structural Performance
Structural Performance
Fastener and steel gauge sizes used throughout this Weather Gard section are nominal.
Fastener Sizes
Fastener Size
Thread Diameter Decimal Equivalent
#8
.165
#9
.181
#10
.190
#12
.216
#14
.250
#17
.291
Steel Gauge Sizes*
Gauge
Decimal Equivalent
*
30
.012
29
.014
26
.018
24
.024
22
.030
20
.036
18
.048
16
.060
14
.075
12
.105
10
.135
Standard steel thickness used for panels, purlins and girts.
Fasteners are designed to withstand a varied range
of types of loading. Each panel or structural system has
its own specific fastener loading requirements. Care
must be taken to ensure that the appropriate loading
requirements for each application are considered.
Typical structural performance criteria that influence
fastener design include:
Ultimate Tension Strength
The point at which a fastener fails under a load
exerted in two direct opposite directions.
Ultimate Shear Strength
The point at which a fastener fails under
a load exerted in offset opposing directions,
usually upon the shank of the fastener.
Typical ultimate shear strengths of each
fastener type are provided on the fastener
information pages.
Pull-out Performance
The ability of a fastener’s threaded connection
to remain intact and resist tensile loads.
Self-tapping fasteners require that a pilot hole be
drilled prior to installation. The pullout resistance
Typical ultimate tension strengths of each fastener type
are provided on the fastener information pages.
Ultimate Torsion Strength
will be directly related to the pilot hole diameter.
Self-drilling fasteners have been developed,
and are available, for most steel construction
applications, to a metal thickness of 1/2". This type
The point at which a fastener fails under a twisting
of fastener is manufactured with its own integral drill
load exerted on the head during installation in
point, which is engineered to drill the optimum hole
a torsional direction.
size to facilitate efficient thread forming in the metal
Typical ultimate torsion strengths of each fastener type
structure, resulting in optimized pullout values.
are provided on the fastener information pages.
Pull-over Performance
The ability of a fastener to resist the pulling of
the fastened sheet material over the head of the
fastener due to gravity, wind, or other load.
The resistance to pullover failure is related to the
strength and diameter of the fastener washer and
the strength and thickness of the metal panel.
6
ZAC
ma™®
MA
ZAC
75
Impax™ — Performance Self-Drill
• Precision cold forged assuring superior point strength
and the fastest drilling time performance through high
strength steel and nested purlins.
• Ultimate performance in light, medium
and heavy gage applications.
12-14 Impax and 1/4-14 Impax lap self-drill
For metal to metal
• Designed and engineered to have low driving and thread
engagement torque and provide maximum clamp load.
• Corrosion resistant coating system.
Application
12-14 Impax
5/16" AF Hex Washer Head
Thread Major Dia: .215 – .209
Thread Minor Dia: .164 – .157
Strength (lbs ult.):
Tensile: 2900
Torsional: 92 in-lbs
Shear: 2050
Pull-out (lbs ult.): 1"– 4"
3/4"
12 ga (.109):
1539
1480
14 ga (.075):
1010
823
16 ga (.060):
724
624
Pull-over with Bond Seal (lbs ult.):
22 ga (.030): 1249
24 ga (.024): 1056
26 ga (.018): 654
Metal to metal
Drilling capacity: .035 – .210
Thickness is based on normal,
single thickness purlin/girt
or multiple material thickness
combined for total.
Min projection: 3/16" of threads
below substratePOSITIVE reduced 00%
1/4-14 Impax Lap
Panel to panel side lap
Some applications may require
attaching light gage (24 – 26 ga)
to sub-structural member.
Composite thickness
should not exceed .095.
File Name: 304 stainless bimetal.eps
Tensile: 3800
Shear: 2850
Pull-out (lbs ult.):22 ga (.030): 379
24 ga (.024): 304
26 ga (.018): 204
Notes
Dimensions are nominal inches unless noted. Self-drill pull-out values (pounds ultimate) are based on 57,000 psi hot rolled steel material. Lap self-drill pull-out values
are based on 40,000 psi AZ55 Galvalume steel sheet material. Ultimate values listed are the result of laboratory testing. The specific job conditions should be considered
and appropriate safety factors applied when specifying the proper fasteners. #12 fasteners 1" and longer have special long pilot lengths to accommodate nested purlins.
Selection
Length
12-14 x 3/4"
12-14 x 1"
12-14 x 1-1/4"
12-14 x 1-1/2"
12-14 x 2"
12-14 2-1/2"
12-14 x 3"
12-14 x 4"
1/4-14 x 7/8"
Part No.
#12 Bond Seal (15 mm)
V2361-EDF
V4577-EDF
V4632-EDF
V4677-EDF
V4777-EDF
S4902-EDF
S4952-EDF
S4981-EDF
—
Part No.
#12 No Washer
A2361F
S4577F
S4632F
S4677F
S4777F
S4902F
S4952F
S4981F
—
Part No.
Part No.
1/4-14 Impax Lap w/ Bond Seal
1/4-14 Lap No Washer
—
—
—
—
—
—
—
—
— File Name: WG3._S5051.eps —
Revised: EWB-00/00/02 —
—
—
—
—
—
V5051-GUF
S5051F
Installation
Tools: 0 – 2000 rpm screwdriver equipped with depth sensing nosepiece.
Options
™
MAC
irius
VistaCoat™
irius
MAC
™
Prisma
Painted
Painted
PRISMA
Sentri
irius irius
irius
™
Stainless
Stainless
®®
™™
™
™™
Self Drilling
Sentri
Prisma
Prisma
SX
irius
irius
®ZAC
™MAC
Self Drilling
SX
BI-METAL
Painted
ZACZAC
MACMAC
ZAC
ZAC
MAC
MAC
PRISMA
PRISMA
BI-METALPainted
Painted
™™
Sentri
Sentri
Sta
S
SX
SXSeS
irius
irius
7
SFS
7 GARD Product Group
3 1 | 1-800-234-4533
55
36intec, Inc. | WEATHER
2
66 1 ?
7-7 www.iMetal.net
4
33
?
2 4 267-983-1017
iMetal.net - Phone:
22
©2012 SFS intec,1Inc.
1
4
Impax™ — Heavy Metal Thickness —
Structural Drill Screws
12-24 Impax 4.5 and 5 self-drill
For metal to metal
• Delivers ultimate performance in medium
Application
12-24 Impax 4.5
Tensile: 3450
Shear: 2420
Pull-out (lbs ult.):
12 ga (.105): 1378
3/16" (.187): Exceeds tensile value
22 ga (.030): 1049
24 ga (.024): 861
26 ga (.018): 584
Metal to metal
single thickness purlin/girt or
multiple material thickness
combined for total.
Thread length:
12-24 x 1-1/4": .650
below substrate
12-24 Impax 5
Tensile: 3450
Shear: 2420
12 ga (.105): 1378
File Name: WG3.1_S4661.eps
22 ga (.030): 1049
Revised: EWB-00/00/02
24 ga (.024): 861
26 ga (.018): 584
Metal to metal
multiple material thickness.
Thread length:
12-24 x 1-1/4": .520
12-24 x 1-1/2": .770
12-24 x 2": 1.020
below substrate
Notes
Dimensions are nominal inches unless noted. Self-drill pull out values (pounds ultimate) are based on 57,000 psi hot rolled steel material. Ultimate values listed
are the result of laboratory testing. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners.
Selection
Length
Part No.
Bond Seal (15 mm)
Part No.
No Washer
Impax 4.5
12-24 x 1-1/4" NEGATIVE
S4661-EDF
reduced 00%
S4661F
Impax 5
12-24 x 1-1/4"
12-24 x 1-1/2"
12-24 x 2"
S4668F
S4741F
A2841F
S4668-EDF
S4741-EDF
A2841-EDF
Installation
irius
Painted
Painted
irius
3
ZAC
Sentri
®
ZACZAC
®®
ZAC
ZAC
8
™
Stainless
™™
SX™ ™Self Drilling
Prisma
Prisma
BI-METAL
™MAC
MACMAC
MAC
MAC
PRISMA
PRISMA
SFS intec,
55 GARD
1 Product Group
66 | 1-800-234-4533
4
77
2 Inc. | WEATHER
irius
irius
Painted
Painted
Sentri
Sentri™ ™
Stainless
Stainless
SelfDrilling
Drilling
SX
SXSelf
BI-METAL
BI-METAL
irius
irius
33
11
22
iMetal.net - Phone: ?267-983-1017
- www.iMetal.net
©2012
44 SFS intec, Inc.
??
ma™
SMA
7
self-drill
Impax™ — Sealer — Drill Screws 12-14 Impax sealer and 1/4-14 lap sealer
For metal to metal
• Integral cupped Hex Washer Head configuration fastener
with an EPDM sealing washer instead of the traditional
bonded sealing washer.
• Precision cold forged assuring superior point strength and
the fastest drilling time performance through high strength
steel and nested purlins.
• Delivers ultimate performance in light, medium
Application
12-14 Sealer Impax
5/16" AF Cupped Hex Washer Head
Tensile: 2900
Shear: 2050
12 ga (.105): 1539
14 ga (.075): 1010
16 ga (.060): 724
Pull-over (lbs ult.):
22 ga (.030): 1298
24 ga (.024): 1102
26 ga (.018): 692
Metal to metal
combined for total.
below substrate
1/4-14 Sealer Impax Lap
to sub-structural member. Composite
thickness should not exceed .095
5/16 Cupped Hex Washer Head
Tensile: 3800
Shear: 2850
22 ga (.030): 379
24 ga (.024): 304
26 ga (.018): 204
Notes
Selection
Part No.
#12 Sealer
V4486-FGF
V4611-FGF
V4636-FGF
V4721-FGF
—
Length
12-14 x 3/4"
12-14 x 1"
12-14 x 1-1/4"
12-14 x 1-1/2"
1/4-14 x 7/8"
Part No.
1/4-14 Sealer Lap
—
—
—
—
V5076-FFF
Installation
Options
irius
VistaCoat™
Painted
Painted
Sentri™
SX
Stainless
Self Drilling
BI-METAL
irius
3
2
1
4
?
9
1/4-14 and 1/4-20 Impax self-drill
Impax™ — 1/4" Drill Screws
• Impax #2 point is designed with a reduced drill point diameter
to provide higher pullout in single purlin attachment.
For metal to metal
• Delivers ultimate performance in medium
•Corrosion resistant coating system.
Application
1/4-14 Impax HWH
#2 Point and #3 Point
#2 – 5/16 AF Hex Washer Head
#3 – 3/8" AF Hex Washer Head
Tensile: 3800
Shear: 2850
#2 Point Pull-out (lbs ult.):
12 ga (.105): 2088
14 ga (.075): 1312
16 ga (.060): 903
12 ga (.105): 1697
14 ga (.075): 1151
16 ga (.060): 687
22 ga (.030): 1079
24 ga (.024): 884
26 ga (.018): 616
Metal to metal
Drilling capacity:
#2 point: .050 – .150
#3 point: .050 – .210
multiple material
thickness
combined for total.
below substrate
1/4-20 Impax HWH
#4 Point
Metal to metal
Drilling capacity:
.060 – .250
Thickness is based
onreduced
normal,
NEGATIVE
00%
combined for total.
below substrate
Tensile: 4200
Shear: 2920
12 ga (.030): 1913
14 ga (.024): 1061
16 ga (.018): 707
22 ga (.030): 1117
24 ga (.024): 988
26 ga (.018): 629
Notes
Dimensions are nominal inches unless noted. Self-drill pull-out values (pounds ultimate) are based on 57,000 psi hot rolled steel material. Ultimate values listed
File Name: WG(1.4)_14_20SpecialApp.eps
Continued on following page
10
Impax™ — 1/4" Drill Screws
Selection
Length
1/4-14 x 3/4"
1/4-14 x 1"
1/4-14 x 1-1/4"
1/4-14 x 1-1/2"
1/4-14 x 2"
1/4-14 x 2-1/2"
1/4-14 x 3"
1/4-14 x 4"
1/4-20 x 3" #4 Point
1/4-20 x 4" #4 Point
1/4-20 x 5" #4 Point
1/4-20 x 6" #4 Point
1/4-20 x 7" #4 Point
1/4-20 x 8" #4 Point
1/4-14 and 1/4-20 Impax self-drill
For metal to metal
Part No.
#3 & #4 Point
Bond Seal
S5010-GBF
S5155-GBF
S5201-GBF
S5251-GBF
S5351-GBF
S5381-GBF
S5451-GBF
S5461-GBF
S5611-GBF
S5621-GBF
S5641-GB
S5661-GB
S5671-GB
S5681-GB
Part No.
#3 & #4 Point
No Washer
S5010F
S5155F
S5201F
S5251F
S5351F
S5381F
S5451F
S5461F
S5611
S5621F
S5641
S5661
S5671
S5681
Part No.
#2 Point Bond Seal
5/16" HWH
—
—
S5191-GBF
S5286-GBF
—
—
—
—
—
—
—
—
—
—
Part No.
#2 Point No Washer
5/16" HWH
—
—
S5191F
S5286F
—
—
—
—
—
—
—
—
—
—
Part No.
#2 Point Bond Seal
3/8" HWH
—
S5171-GBF
—
S5271-GBF
—
—
—
—
—
—
—
—
—
—
Part No.
#2 Point No Washer
3/8" HWH
—
S5171F
—
S5271F
—
—
—
—
—
—
—
—
—
—
Installation
Options
irius
Painted
Painted
Sentri™
SX
Stainless
Self Drilling
BI-METAL
irius
3
2
1
4
?
11
Impax™
• Precision cold forged assuring superior point strength and the
fastest drilling time performance.
• Ultimate performance in light and medium gage applications.
Utility Self-Drill
• Designed to provide maximum clamp load.
Application
8-18 Impax
#2 Point
1/4" AF Capped Hex Washer Head
Thread Major Dia: .163
Thread Minor Dia: .119
Tensile: 1575
Shear: 1035
14 ga (.075): 1084
16 ga (.060): 783
18 ga (.048): 389
22 ga (.030): 924
24 ga (.024): 668
26 ga (.018): 421
10-16
#3 Point
Thread Minor Dia: .138
Tensile: 1825
Shear: 1535
12 ga (.105): 1782
14 ga (.075): 1072
16 ga (.060): 782
Drilling capacity: .035-.140
combined for total.
below substrate
Drilling capacity: .035-.150
combined for total.
below substrate
Notes
Dimensions are nominal inches unless noted. Self-drill pull-out values (pounds ultimate) are based on 57,000 psi hot rolled steel material. Ultimate values listed
Selection
Impax 1/4 HWH Self Drill
8-18 x 1/2 HWH SD #2
With Bond Seal
S1050-BBF
8-18 x 5/8 HWH NIB SD #2
8-18 x 3/4 HWH SD #2
Impax 5/16 HWH Self Drill
10-16 x 5/8 HWH SD #2
Without Bond Seal
S1050F
—
S1320F
S1350-BBF
S1350F
With Bond Seal
S2401-CDF
Without Bond Seal
S2401F
10-16 x 3/4 HWH SD #3
S2701-CDF
S2701F
10-16 x 1 HWH SD #3
S3301-CDF
S3301F
10-16 x 1-1/4 HWH SD #3
S3601-CDF
S3601F
10-16 x 1-1/2 HWH SD #3
S3901-CDF
S3901F
Installation
Options
irius
Painted
Painted
Sentri™
SX
Stainless
Self Drilling
BI-METAL
irius
3
12
1 Product Group | 1-800-234-4533
4
2 Inc. | WEATHER GARD
SFS intec,
?
12-14 and 1/4-14 lap self-drill
410 Stainless
For metal to metal
• 410 SS is a magnetic heat-treatable stainless steel.
• Type 410 self-drilling fasteners provide fair resistance to
corrosion in mild to light industrial environments.
Application
12-14 Stainless SD
#3 Point
Thread Major Dia: .215 - .209
Thread Minor Dia: .164 - .157
Tensile: 2800
Shear: 1900
Point Pull-out (lbs ult.):
12 ga (.109): 1480
14 ga (.075): 823
16 ga (.060): 624
22 ga (.030):1249
24 ga (.024): 1056
26 ga (.018): 654
Metal to metal
combined for total.
below substrate
1/4-14 Stainless Lap
Tensile: 3850
Shear:2850
22 ga (.030): 379
24 ga (.024): 304
26 ga (.018): 204
Composite thickness
should not exceed .095.
Notes
Dimensions are nominal inches unless noted. Self-drill pull-out values (pounds ultimate) are based on 57,000 psi hot rolled steel material. Lap self-drill pull-out values are based on
40,000 psi AZ55 Galvalume steel sheet material. Ultimate values listed are the result of laboratory testing. The specific job conditions should be considered and appropriate safety
factors applied when specifying the proper fasteners. #12 fasteners 1" and longer have special long pilot lengths to accomodate nested purlins.
Selection
Part No.
#12 Bond Seal
G0325-FBF
G0340-FBF
G0801-FBF
G0810-FBF
—
Length
12-14 x 3/4" SD3
12-14 x 1" SD3
12-14 x 1-1/4" SD3
12-14 x 1-1/2" SD3
1/4-14 x 7/8"
Part No.
#12 No Washer
G0325F
G0340F
G0801F
G0810F
—
Part No.
1/4-14 Lap w/ Bond Seal
—
—
—
—
G0773-GWF
Part No.
1/4-14 Lap No Washer
—
—
—
—
G0773F
Installation
Options
irius
Painted
Painted
Sentri™
SX
Stainless
Self Drilling
BI-METAL
irius
3
2
1
4
?
13
Wood to Metal
Flat Head Utility Self-Drill
• Designed for attaching wood substrates to steel.
• Phillips drive and head design for counter sinking.
For attaching plywood to steel
• More threads per inch for optimum holding power.
Application
Ply Metal Self-Drill
10-24 Wafer Head
Head Dia: .445
#2 Phillips Drive
Header Self-Drill
with Wings
12-24 Flat Head
Head Dia: .413
#3 Phillips Drive
1/4-20 Flat Head
Header Self-Drill
Head Dia: .479
#3 Phillips Drive
Notes
Dimensions are nominal inches unless noted. The specific job conditions should be considered and appropriate safty factors applied when specifying the proper fasteners.
Selection
Length
10-24 x 3/4"
10-24 x 1"
10-24 x 1-7/16"
12-24 x 2"
12-24 x 2-1/2"
1/4-20 x 2-3/4"
Wood Thickness
3/8" plywood
1/2" plywood
3/4" plywood
up to 1"
up to 1-1/2"
up to 1-3/4"
Steel Thickness
.060-.175
.060-.175
.060-.175
.060-.210
.060-.210
.095-.250
Part No.
A1500
A1565
A1567
A2844
A2860
A5085
Installation
14
ma™
SMA
7
ZAC 5/16" HWH
Zinc aluminum capped drill screws
ZAC® Impax™ —
5/16" HWH Alloy Capped
For metal to metal
• Integral cupped Hex Washer Head can never red rust.
engagement torque while providing maximum clamp load.
• ZAC: the most widely used zinc aluminum capped
fastener in the industry.
Application
12-14 ZAC (5/16")
5/16" AF Zinc Aluminum Capped
Hex Washer Head
Tensile: 2900
Shear: 2050
12 ga (.105): 1539
14 ga (.075): 1010
16 ga (.060): 724
22 ga (.030): 1647
24 ga (.024): 1310
26 ga (.018): 794
Metal to metal
combined for total.
below substratePOSITIVE reduced 00%
1/4-14 ZAC Lap (5/16")
Composite thickness should not
exceed .095 thickness.
Hex Washer Head
Tensile: 3800
Shear: 2850
22 ga (.030): 379
24 ga (.024): 304
26 ga (.018): 204
Notes
Dimensions are nominal inches unless noted. Self-drill pull-out values (pounds ultimate) are based on 57,000 psi hot rolled steel material. Lap self-drill pull-out values are
based on 40,000 psi AZ55 Galvalume steel sheet material. Ultimate values listed are the result of laboratory testing and we believe typical. The specific job conditions should be
considered and appropriate safety factors applied when specifying the proper fasteners. #12 fasteners 1" and longer have special long pilot lengths to accommodate nested
purlins.
Selection
Length
Part No.
12-14 ZAC
Part No.
1/4-14 ZAC Lap
5/16" AF Hex Washer Head ZAC
12-14 x 1"
12-14 x 1-1/4"
12-14 x 1-1/2"
12-14 x 2"
1/4-14 x 7/8"
S4591-FLF
X4646-FLF
X4731-FLF
S4761-FLF
—
—
—
—
S5031-FMF
File Name: 304 stainless bimetal.eps
Installation
Options
irius
VistaCoat™
Painted
Painted
Sentri™
SX
Stainless
Self Drilling
BI-METAL
irius
3
2
1
4
?
15
ZAC® Impax™ —
• ZAC: the most widely used zinc aluminum capped
fastener in the industry.
ZAC 3/8" HWH
For metal to metal
engagement torque while providing maximum clamp load.
Application
12-14 ZAC (3/8")
Hex Washer Head
Tensile: 2900
Shear: 2050
12 ga (.105): 1539
14 ga (.075): 1010
16 ga (.060): 724
22 ga (.030): 1647
24 ga (.024): 1310
26 ga (.018): 794
Metal to metal
single thickness purlin/girt or multiple
material thickness combined for total.
below substrate.
1/4-14 ZAC Lap (3/8")
attaching light gage (24 – 26 ga) to
sub-structural member. Composite
thickness should not exceed
.095 thickness.
NEGATIVE
reduced 00%
00%
POSITIVE reduced
12-14 x 3/4 ZAC Lap (3/8")
Hex Washer Head
Tensile: 3800
Shear: 2850
22 ga (.030): 379
24 ga (.024): 304
26 ga (.018): 204
Hex Washer Head
Tensile: 2100
Shear: 1800
Pull-out (lbs ult.)
22 ga (.030): 538
24 ga (.024): 430
26 ga (.018): 330
Sharp point
Panel to panel
Drilling capacity .030 – .060
Self-piercing points are not designed
for attaching light gage (24 – 26 ga)
Notes
and appropriate safety factors applied when specifying the proper fasteners #12 fasteners 1" and longer have special long pilot lengths to accommodate nested purlins.
File Name: WG5.2_A1653.eps
16
ma™
SMA
7
ZAC 3/8" HWH
ZAC® Impax™ —
Selection
For metal to metal
Part No.
12-14
Length
3/8" Hex Washer Head ZAC
12-14 x 3/4"
12-14 x 1"
12-14 x 1-1/4"
12-14 x 1-1/2"
12-14 x 2"
12-14 x 2-1/2"
12-14 x 3"
1/4-14 x 7/8"
Part No..
1/4-14 Lap)
A1653-FLF Sharp Point LAP
—
S4576-FLF
—
S4631-FLF
—
S4676-FLF
—
S4776-FLF
—
S4901-FLF
—
S4951-FLF
—
—
S5065-FMF
Installation
Options
irius
VistaCoat™
Painted
Painted
Sentri™
SX
Stainless
Self Drilling
BI-METAL
irius
3
2
1
4
?
17
ZAC® Impax™
ZAC® self-drill 3/8" HWH
For metal to metal and insulated panel to metal
engagement torque to prevent damage to the cap during
installation while providing maximum clamp load.
• ZAC: the most widely used zinc aluminum capped fastener
in the industry.
• Precision cold forged assuring superior point strength and
the fastest drilling time performance through high strength
steel and nested purlins.
Application
12-24 ZAC (3/8")
Hex Washer Head
Tensile: 3450
Shear: 2420
12 ga (.105): 1378
Pull-over with assembled
Seal washer (lbs ult.):
22 ga (.030): 1647
24 ga (.024): 1310
26 ga (.018): 794
4.5 point and 5 point
Metal to metal
Impax 4.5
Impax 5
Thickness is based on single
thickness purlin/girt or multiple
Thread length: POSITIVE reduced 00%
ZAC 4.5: 12-24 x 1-1/4": .650
ZAC 5: 12-24 x 1-1/4": .520
12-24 x 1-1/2": .770
12-24 x 2": 1.020
below substrate
Notes Dimensions are nominal inches unless noted. Self-drill pull-out values (pounds ultimate) are based on 57,000 psi hot rolled steel material. Lap self-drill pull-out values
and appropriate safety factors applied when specifying the proper fasteners #12 fasteners 1" and longer have special long pilot lengths to accommodate nested purlins.
Selection
Length
12-24 x 1-1/4" (4.5)
12-24 x 1-1/4" (5)
12-24 x 1-1/2" (5)
Part No.
12-14 Insulated
—
—
—
Part No.
Panel
12-24 (4.5 ) and 12-24 (5)
Thickness
S4665-FLF
—
Created by:
S4669-FLF
—EWB-11/27/02
S4742-FLF
—
Installation
irius
Options
Painted
Painted
Sentri™
SX
Stainless
Self Drilling
BI-METAL
irius
3
2
1
4
?
18
MAC™ Impax™ — 5/16" HWH
300 Series Stainless Capped Self-Drill
• MAC has a 300 series stainless steel capped, integral cupped
Hex Washer Head configuration that can never red rust.
MAC stainless capped drill screws
For metal to metal
Application
12-14 MAC
5/16” AF Stainless Capped
Hex Washer Head
Tensile: 2900
Shear: 2050
12 ga (.105): 1539
14 ga (.075): 1010
16 ga (.060): 724
22 ga (.030): 1298
24 ga (.024): 1102
26 ga (.018): 692
Assembled with EPDM washer
Metal to metal
combined for total, as in overlapped
or nested purlin construction.
Min projection: 3/16"
of threads
below substrate
1/4-14 MAC Lap
5/16” AF Stainless Capped Hex
Washer Head
Tensile: 3800
Shear: 2850
22 ga (.030): 379
24 ga (.024): 304
26 ga (.018): 204
to sub-structural
member.
POSITIVE
reduced 00%
Composite thickness should not
exceed .095 thickness.
12-24 MAC 4.5
5/16” AF Stainless Capped Hex Washer Head
Tensile: 3450
Shear: 2420
12 ga (.105): 1378
22 ga (.030): 1049
24 ga (.024): 861
26 ga (.018): 584
Metal to metal
combined for total.
Nominal thread length:
12-24 x 1-1/4": .650
00%
Min projection: NEGATIVE
3/16" ofreduced
threads
below substrate POSITIVE reduced 00%
Notes
Dimensions are nominal inches unless noted. Self-drill pull out values (pounds ultimate) are based on 57,000 psi hot rolled steel material. Lap self-drill pull out values are
based on 40,000 PSI AZ55 Galvalume steel sheet material. Ultimate values listed are the result of laboratory testing The specific job conditions should be considered
Installation
Selection
Part No.
Length
12-14 MAC
12-14 x 1"
S4530-FAF
12-14 x 1-1/4"
S4650-FAF
ZAC®
12-14 x 1-1/2"
S4690-FAF
12-14 x 2"
S4770-FAF
1/4-14 x 7/8"
— ZAC
NEGATIVE reduced
12-24 x 1-1/4" (4.5)
— 00%
Part No.
1/4-14 MAC
—
—
™
—MAC
—
S5100-GGF
MAC
—
Part No.
12-24 MAC
—
—
™
Prisma
—
—
—PRISMA
S4672-FAF
Tools: 0 – 2000 rpm screwdriver equipped with depth
sensing nosepiece.
Options
irius
VistaCoat™
Painted
Painted
Sentri™
5
6
7
Stainless
Self Drilling
irius
SX
3
2
1
4 19
BI-M
ZAC self-tapping fasteners:
AB milled point
ZAC® 3/8" HWH
Alloy Capped Tapping Fasteners
• Integral cupped Hex Washer Head configuration can never red rust.
• Designed for attaching both metal to wood and metal to metal.
For metal to metal
• Milled points do not require a pre-drilled hole when
attaching 26 and 24 gage metal to wood.
Application
1/4 -14 ZAC Type AB
Milled Point
Hex Washer Head
Tensile: 3800
Shear: 2850
22 ga (.030): 379
24 ga (.024): 304
26 ga (.018): 204
Metal to wood
Metal to metal
Self-Drilling Metal Thickness:
Sheet .018 – .030
single or multiplePOSITIVE
material
thickness
reduced
00%
combined for total
Min depth penetration into the
wood sub structure: 1"
#17 Zac Type AB
Strip-out Repair
3/8 AF Hex Head
Metal to metal
Repair fastener for stripped out
#14 Type A or 1/4" AB
below substrate
Notes
Dimensions are nominal inches unless noted. When using Milled point fasteners for metal to metal see the tapping screw section for performance values. Pull-out values
(pounds ultimate) are based on 57,000 psi hot rolled steel material. Lap self-drill pull-out values are based on 40,000 psi AZ55 Galvalume steel sheet material. Ultimate values
listed are the result of laboratory testing. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners.
Selection
Length
3/8" ZAC
1"
1-1/2"
2"
2-1/2"
Part No.
1/4-14 AB
A4395-FMF
A4485-FMF
A4513-FMF
A4510-FMF
Part No.
#17 AB
Length
17 x 1"
17 x 1-1/2"
A6045-LFF
A6066-LFF
Installation
Tools: Metal to metal application: 0 – 600 rpm screwdriver equipped with depth sensing nosepiece.
Metal to wood application: 0 – 2500 rpm screwdriver equipped with depth sensing nosepiece.
irius
Options
Painted
Painted
Sentri™
SX
Stainless
Self Drilling
BI-METAL
irius
3
2
1
4
?
20
Capped Fasteners
Prisma™
• Prisma nylon head is absolutely corrosion proof.
• Nylon head can withstand extreme installation
torque without failure.
• Requires no special socket for installation.
Nylon headed fasteners:
self-tapping, self-drill and Woodgrip™
For metal to metal and metal to wood
• Special washer face allows the fastener to be used
on sidewall without a sealing washer.
• Nylon heads are available in 90 standard colours.
Application
#14 Type AB
7/16" Nylon Hex Washer Head
1/4-14:
Tensile: 3800
Shear: 2560
1/4-14 AB Carbon Steel:
12 ga (.105): 2185
14 ga (.075): 1277
16 ga (.060): 879
1/4-14 #3 Point Carbon Steel:
Pull-out: (lbs ult.):
12 ga (.105): 1697
14 ga (.075): 1151
16 ga (.060): 687
Metal to metal
Self-Tapping AB:
1/4-14 x 3/4"
1/4-14 x 1-1/2"
1/4-14 x 2"
1/4-14 x 2-1/2"
1/4-14 x 3"
Stainless AB: POSITIVE reduced 00%
1/4-14 x 3/4"
Self-Drill:
1/4-14 x 1"
1/4-14 x 1-3/8"
1/4-14 x 2"
Drill capacity: .050 – .210
1/4-14 x 7/8 Lap
Metal to metal
drilling capacity: .030 – .095
Self-Drilling Metal Thickness:
single or multiple
material thickness
combined for total.
File Name: WG5.5_prisma2b.eps
1/4-14:
Tensile: 3800
Shear: 2560
#10 Woodgrip
Woodgrip Prisma
Tensile: 1500
Torsional: 60 in-lbs min
Shear: 933
Metal to wood
10 x 1"
10 x 1-1/2"
10 x 2"
10 x 2-1/2"
10 x 3"
Notes
Name:
EG5.5_prisma4.eps
Dimensions are nominal inches unless noted. For Type AB metal to metal, see tappingFile
screw
section
for performance values.
File Name: WG5.5_prisma1.eps
Options
None
21
Self-tapping — Type A. AB, B
Tapping Screws — Carbon Steel
For metal to metal
• Carbon steel zinc-plated self-tapping fasteners are the original metal
construction fastener that can be used in metal to metal and metal to wood applications.
• Tapping screws are available in long lengths for specialty applications.
Application
#14 Type A
3/8" AF Hex Head
Tensile: 3500
Shear: 2400
14 ga (.075): 1318
16 ga (.060): 958
18 ga (.048): 605
22 ga (.030): 1097
24 ga (.024): 810
26 ga (.018): 564
Metal to metal
Attachment thickness: .044 – .075
Metal thickness
Drill bit size
.021 – .026
1/8 (.125)
.027 – .050
3/16 (.187)
.051 – .075
#8 (.199)
The hole size determines installation
performance and
pullout strength.
Thickness is based on normal, single
thickness purlin/girt or multiple
below substrate
#14 Type A Milled Point
Carbon Steel, Silver Sentri
Metal to wood
Self-drilling metal thickness:
Sheet .018 – .030
single or multiple material thickness
combined for total.
POSITIVE into
reduced
00%
Min depth penetration
the
wood sub structure:
1"
1/4 Type AB and B
Metal to metal
Metal thickness
Drill bit size
AB .021 – .026
1/8 (.125)
AB .027 – .050
5/32 (.156)
AB .051 – .075
#8 (.199)
AB .075 – .110
#7 (.201)
B .065 – .085
#8 (.199)
B .085 – .115 POSITIVE#7reduced
(.201)
00%
B .115 – .375
#1 (.228)
B .375 – .500
#1 or
larger,
NEGATIVE
reduced
00% depending on hardness of steel
combined for total.
below substrate
Tensile: 3500
Shear: 2400
1" SPF wood: 1013
22 ga (.030): 1097
24 ga (.024): 810
26 ga (.018): 564
3/8" AF Hex Head
Tensile: 3800
Torsional:142 in-lbs
Shear: 2560
12 ga (.105): 2185
14 ga (.075): 1277
16 ga (.060): 879
22 ga (.030): 1094
24 ga (.024): 866
26 ga (.018): 600
Notes
Dimensions are nominal inches unless noted. Pull-out values (pounds ultimate) are based on 50,000 psi hot rolled steel sheet material. Ultimate values listed are the result
of laboratory testing. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners.
22
ma™
SMA
7
Self-tapping — Type A. AB, B
Tapping Screws — Carbon Steel
For metal to metal
Application
#17 Type AB
3/8" AF Hex Head
Strip out repair Type A or AB
Metal to metal
below substrate
Notes
Selection
Length*
3/4"
1"
1-1/4"
1-1/2"
2"
2-1/2"
3"
3-1/2"
4"
5"
6"
#17 x 3/4"
#17 x 1"
#17 x 1-1/2"
Part No.
#14 A Bond Seal
A2980-GB
A3240-GB
A3420-GB
A3460-GB
A3520-GB
A3580-GB
A3620-GB
A3640-GB
A3680-GB
A3720-GB
A3740-GB
—
—
—
Part No.
#14 A Milled Point Bond Seal
—
V3321-GBF
—
V3438-GBF
V3531-GBF
A3597-GBF
A3626-GBF
—
—
—
—
—
—
—
Part No.
1/4 AB & #17 AB Bond Seal
A4320-GB
A4420-GB
A4440-GB
A4500-GB
—
—
—
—
—
—
—
A6020-KJ
A6040-KJ
A6060-KJ
Part No.
1/4 B Bond Seal
A3800-GB
A3860-GB
—
A3920-GB
A4000-GB
A4040-GB
A4080-GB
A4140-GB
A4220-GB
A4260-GB
A4280-GB
—
—
—
*Longer lengths available upon request
Installation
Tools: 0 – 1000 rpm on type B screwdriver equipped with depth sensing nosepiece.
Options
irius
VistaCoat™
Painted
Painted
irius
3
Sentri
ZAC ®ZAC
®
ZAC
2
5 1
™
Stainless
™
MAC
irius
SX ™Self DrillingPrisma
BI-METAL
MAC
6
7
Sentri™
2
1
SX
Stainless
Self Drilling
irius
PRISMA
4
Painted
?
3
4
23
B
Tapping Screws — 300 Series
(RH2) Product Name: #14
Stainless Steel
• Stainless steel zinc-plated self-tapping fasteners are
designed for attaching metal to metal and metal to wood.
• Type B have wax surface treatment for added lubricity.
Stainless
(RH3) self-tapping
Description: —
#3Type
Phillips
A, AB,
Drive
B
(RH4) Application: Insulation board
For metal
to roof
tocover.
metal
• Stainless tappers are used in high corrosive environments
or where corrosions free performance is required to meet
the design life of the project.
Application
#14 Type A 304 Stainless
3/8" AF 304 Stainless Hex Head
Tensile: 3370
Shear: 1520
Pull-out (lbs ult.)
14 ga (.075): 1232
16 ga (.060): 1110
22 ga (.030): 1237
24 ga (.024): 790
26 ga (.018): 647
Metal to metal
Metal thickness
Drill bit size
.021 – . 026
1/8 (.125)
.027 – . 050
3/16 (.187)
.051 – . 075
#8 (.199)
The hole size determines installation
performance and pullout strength.
Thickness is based
on normal,
combined for total.
below substrate
Type AB and B 304
Stainless
Metal to metal
Metal thickness
Drill bit size
AB .021 – .026
1/8 (.125)
AB .027 – .050
5/32 (.156)
AB .051 – .075
#8 (.199)
AB .075 – .104
#7 (.201)
reduced 00%
B .065 – .085 NEGATIVE
#8 (.199)
B .085 – .115
#7 (.201)
B .115 – .375
#1 (.228)
B .375 – .500
#1 or larger, depending on hardness of steel
combined for total.
below substrate
File Name: WG7.2_E0600.eps
#17 Type AB 304 Stainless
3/8" AF 304 Stainless Hex Head
Tensile: 3800
Shear: 2350
12 ga (.105): 2310
14 ga (.075): 1394
16 ga (.060): 1250
22 ga (.030): 1237
24 ga (.024): 790
26 ga (.018): 647
3/8" 304 Stainless AF Hex Head
Strip out repair Type A or AB
Metal to metal
below substrate
Notes
24
Tapping Screws — 300 Series
Stainless Steel
Selection
Length
3/4"
1"
1-1/4"
1-1/2"
2"
2-1/2"
3"
3-1/2"
4"
5"
6"
7"
8"
#17 x 3/4"
#17 x 1"
#17 x 1-1/2"
Stainless self-tapping — Type A, AB, B
For metal to metal
Part No.
#14 A Bond Seal
E0500-HP
E0600-HP
E0640-HP
E0660-HP
E0700-HP
E0720-HP
E0740-HP
E0760-HP
E0780-HP
E0820-HP
E0840-HP
E0850-HP
E0855-HP
—
—
—
Part No.
1/4 AB & #17 AB Bond Seal
E1240-HP
E1300-HP
E1310-HP
E1320-HP
—
—
—
—
—
—
—
—
—
E1960-KP
E1980-KP
E2000-KP
Part No.
1/4 B Bond Seal
E0860-HPW
E0880-HPW
—
E1000-HPW
E1060-HPW
E1080-HPW
E1100-HPW
E1120-HPW
E1140-HPW
E1180-HPW
E1200-HPW
E1210-HPW
E1215-HPW
—
—
—
Installation
irius
Options
Painted
Painted
Sentri™
SX
Stainless
Self Drilling
BI-METAL
irius
3
2
1
4
?
25
Architectural Fasteners
SX Stainless Self-Drill
• SX Austenitic stainless fasteners come with a Bi-metal welded
carbon steel point.
• SX Austenitic stainless product line offers fastening solutions
for attaching panels from very thin to 1/2" structural steel.
• Provides ultimate corrosion performance for attaching steel,
stainless or aluminum panels.
• Designed for secured attachment to both panel and substructures.
SX austenitic stainless steel
For metal to metal
• Stainless self-drill fasteners are engineered to have
low driving torque and provide maximum clamp load.
• Ultimate drill performance in light, medium, and
heavy gage applications.
• Washer O.D designed for both sidewall and roof
panel attachment.
Application
SX3 Self-Drill
Dia: Nominal #14
Tensile: 2535
Shear: 1864
12 ga (.105): 1125
14 ga (.075): 855
16 ga (.060): 610
24 ga (.024): 1300
26 ga (.018): 705
5/8" O.D Stainless Bond Seal
Metal to metal
SX5 Self-Drill
Dia: Nominal #12
Tensile: 2735
Shear: 2240
12 ga (.105): 1399
14 ga (.075): 795
16 ga (.060): 582
24 ga (.024): 1190
26 ga (.018): 665
Metal to metal
SX14 Self-Drill
Dia: Nominal #12
Tensile: 2695
Shear: 2695
12 ga (.105): 1220
24 ga (.024): 1150
26 ga (.018): 646
Metal to metal
SL2-S Free Spin Lap
Self-Drill
Dia: Nominal #14
Tensile: 3740
Shear: 2790
1/2" (14mm) O.D. for #12
5/8" (16mm) O.D. for #14
Stainless Bond Seal
Metal to metal
Dia: Nominal #12
Tensile: 1670
Shear: 1370
26
SX Stainless Self-Drill
For metal to metal
Application continued
SXC14 Self-Drill Standoff
Dia: Nominal #12
Tensile: 3150
Shear: 2780
Insulated panel to metal
#5 Point
SXCW Self-Drill
Dia: Nominal 1/4"
Tensile: 3934
Shear: 2450
Insulated panel to wood
Selection
Length
SX3 Self-Drill Stainless HWH
14-11 x 1-1/8 SD
14-11 x 1-1/2 SD
14-11 x 2 SD
12-14 x 1-1/4 SD
12-14 x 1-1/2 SD
12-14 x 1-5/8 SD
12-14 x 2-1/8 SD
12-14 x 3-1/8 SD
12-14 x 3-3/4 SD
12-14 x 4-1/4 SD
12-14 x 5-1/2 SD
SL2 Lap Self-Drill Stainless HWH
12-11 x 1 Lap SD
1/4-14 x 1-1/8 Lap SS
Part No.
Bond Seal
Part No.
No Washer
1141978
1133237
1133239
1141971
1142006
1142057
1122767
1123168
1134477
1133684
1133330
1141958
1141963
1141967
1134304
1133976
1134478
1154328
1133309
1141957
1141962
1141966
1123164
1133512
1133482
-
Installation
® rpm screwdriver™equipped with depth
Tools: 0 –ZAC
2000
nosepiece.
MAC
Prisma
ZAC®™ sensing MAC
irius™
ZAC
MAC
PRISMA
ZAC
irius
MAC
5
6
75
63
Length
12-14 x 1-9/16 SD 5
12-14 x 1-7/8 SD 5
12-14 x 2-1/2 SD 5
12-14 x 3-1/4 SD 5
12-14 x 4 SD 5
Length
SXC14 Self-Drill
12-14 x 3-1/8"
12-14 x 3-3/4"
12-14 x 4-5/8"
12-14 x 5-1/2"
12-14 x 6-5/8"
SXCW Self-Drill
14 x 3-1/2"
14 x 4-1/8"
14 x 4-9/16"
14 x 5-3/8"
14 x 6-1/4"
Options
™
Prisma
Painted
Painted
PRISMA
7 2
Sentri
irius irius
™
Part No.
Bond Seal
Part No.
No Washer
0770785
0773625
0770805
0770786
0773627
0770804
0523277
0768379
0526400
0777580
Part No.
Bond Seal
Panel
Thickness
0773620
0775732
0776324
0768491
1185167
1-1/2" — 1-7/8"
1-7/8" — 2-1/2"
2-5/8" — 3-5/16"
3-5/16" — 4-1/8"
4-1/8" — 5-5/16"
0998230
0997836
0998241
0997821
0997840
1-1/8" — 1-7/16"
1-1/2" — 2-1/8"
1-7/8" — 2-9/16"
2-5/8" — 3-5/16"
3-1/16" — 4-1/8"
Stainless
SX Self Drilling
Painted
™
Sentri
BI-METAL
SX
Stainless
Self Drilling
irius
3 1
2 4
1
?
27
4
irius SX austenitic stainless steel
irius® SX Stainless Self-Drill
• irius is a patented drive system available on a full range
of metal building fasteners.
• irius SX stainless fasteners’ low profile head that has changed
the future architectural appearance of sidewall fastening.
• Fastening system drive socket insures positive engagement
and prevents damage to a painted fastener head.
For metal to metal
• Self-drilling point design assures superior point strength and
the excellent drill performance through high strength steel.
• Stainless fasteners provide the ultimate corrosion
performance for attaching steel, stainless or aluminum panels.
• SX austenitic stainless self-drill fasteners are engineered to
have low driving torque and provide maximum clamp load.
Application
SX 3-L12 irius Self-Drill
irius low profile and drive system
Dia: Nominal #14
Tensile: 2535
Shear: 1864
12 ga (.105): 1125
14 ga (.075): 855
16 ga (.060): 610
24 ga (.024): 1300
26 ga (.018): 705
1/2" O.D Aluminum Bond Seal
Metal to metal
Dia: Nominal #12
Tensile: 2735
Shear: 2240
12 ga (.105): 1399
14 ga (.075): 795
16 ga (.060): 582
24 ga (.024): 1190
26 ga (.018): 665
Metal to metal
Dia: Nominal #12
Tensile: 2695
Shear: 2695
12 ga (.105): 1220
24 ga (.024): 1150
26 ga (.018): 646
Metal to metal
SL2-S-L12 irius Free Spin
Lap Self-Drill
Dia: Nominal #12
Tensile: 1670
Shear: 1370
1/2" or 5/8" O.D
Stainless Bond Seal
Metal to metal
File Name: WG3_SX14.eps
28
irius SX austenitic stainless steel
irius® SX Stainless Self-Drill
Selection
For metal to metal
Length
SX3-L12 irius Self-Drill
14 x 1-1/8 SD
14 x 1-1/2 SD
12-14 x 1-1/4 SD
12-14 x 1-1/2 SD
12-14 x 1-5/8 SD
12-14 x 2-1/8 SD
12-14 x 1-9/16 SD
SL2-L12 irius Free Spin Lap Self Drill
1/4-14 x 1 Lap SD 14mm SS Bond Seal
1/4-14 x 1 Lap SD 16mm SS Bond Seal
Part No.
Bond Seal
Part No.
No Washer
1142002
1196328
1142001
1142030
1134345
1134359
1135437
1144693
1134342
1134355
1135452
1241511
0776328
0776332
1135477
1147314
Installation
The E420 irius drive socket (part #0973316) is required.
irius
Options
Painted
Painted
Sentri™
SX
Stainless
Self Drilling
BI-METAL
irius
3
2
1
4
?
29
SX TORX® Self-Drill
• SX Austenitic stainless fasteners come with a Bi-metal welded
carbon steel point.
• SX Austenitic stainless product line offers fastening solutions
for attaching panels from very thin to medium gage applications.
• Provides ultimate corrosion performance for attaching steel,
stainless or aluminum panels.
For metal to metal
• Low profile TORX drive for aesthetic installed appearance
• Designed for secured attachment to both panel and substructures.
• Stainless self-drill fasteners are engineered to have low driving
torque and provide maximum clamp load.
• Ultimate drill performance in light and medium gage applications.
Application
SX 3-D10 TORX® Self-Drill
Metal to metal
Drill capacity: .039 –.118”
SX 5-D12 TORX® Self-Drill
Metal to metal
Drill capacity: .060–.157”
SL2-S-D12 Lap TORX®
Self-Drill
3/8” O.D. Aluminum Bond Seal
Metal to metal
Drill capacity: .060”
Drive
Head Dia
Thread Major Dia
Thread Minor Dia
Strength (ult.):
Tensile:
Shear:
Pull-out (ult.):
12 ga (.105):
14 ga (.075):
16 ga (.060):
TORX® T20W
.404-.384”
.189-.183”
.141-.135”
Drive
Head Dia
Thread Major Dia
Thread Minor Dia
Strength (ult.):
Tensile:
Torsional:
Shear:
Pull-out (ult.):
12 ga (.105):
14 ga (.075):
16 ga (.060):
TORX® T-25
.482 - .462”
.215 - .211”
.164 - .157”
Drive
Head Dia
Thread Major Dia
Thread Minor Dia
Strength (ult.):
Tensile:
Torsional:
Shear:
Pull-out (ult.):
16 ga (.060):
18 ga. (.048):
TORX® T20W
.482 - .462”
.216 - .208”
.134 - .126”
1960 lbs
1456 lbs
1189 lbs
854 lbs
696 lbs
2735 lbs
2240 lbs
70 lb-in
1399 lbs
795 lbs
582 lbs
1670 lbs
70 lb in
1370 lbs
902 lbs
668 lbs
Notes
Dimensions are nominal unless noted. The specific job conditions should be considered and appropriate safty factors applied when specifying the proper fasteners.
30
SX TORX® Self-Drill
Selection
For metal to metal
Length
SX3-D10 TORX®
10-16 x 1 SD T20W
12-11 x 1-3/16 SD T25
SX5-D12 TORX®
12-11 x 1-1/2 SD
SL2-S-D12 Lap TORX®
12 x 1 LAP SD
Part No.
Bond Seal
Part No.
No Washer
—
—
1193547
1235148
1133806
1133805
1135881
1137560
Installation
Fasteners should provide for a minimum of 3 fully developed threads through the metal substrate.
Tools: 0-2000 rpm screwdriver equipped with depth sensing nosepiece.
T20W or T25 TORX drive bit.
irius
Options
Painted
Painted
Sentri™
SX
Stainless
Self Drilling
BI-METAL
irius
3
2
1
4
?
31
Fastening cladding to timber battens,
aluminum and steel framework
TW-S Stainless Self-Tapping
• 304 Stainless Steel provides maximum resistance to corrosion.
• Aesthetic fastening system for attaching cladding panels to
timber battens, aluminum and steel framework.
• Low profile TORX® drive head can be colored to match any
cladding panel.
Application
TW-S-D12
#10-12 Self-Tapping
Drive:
Head Dia:
Thread Major Dia:
Thread Minor Dia:
Nom. Tensile:
Min. Torsional:
Nom. Shear:
Cladding Panel to Wood
Material: 304 Austentic
Stainless Steel
TORX® T20W
.492 - .453”
.194 - .188”
.134 - .129”
1596 lbs
60 lb-in
1213 lbs
Pull-out Strength - SYP Dimensional Lumber
1/4”:
481 lbs
Pull-out Strength - Plywood
3/4”:
578 lbs
5/8”:
438 lbs
1/2”:
348 lbs
Pull-out Strength - OSB (Oriented Strand Board)
23/32”:
449 lbs
19/32”:
412 lbs
7/16”:
228 lbs
TW-S-D13
#12-11 Self-Tapping
Cladding Panel to Metal
Drive:
Head Dia:
Thread Major Dia:
Thread Minor Dia:
TORX® T20W
.531” - .493”
.221” - .215”
.162” - .155”
Material: 304 Austentic
Stainless Steel
Nom. Tensile:
Min. Torsional:
Nom. Shear:
2144 lbs
65 lb-in
2200 lbs
Pull-out Strength - Extruded Aluminum
1/8”:
800 lbs pre-drill: 13/64 (.203”)
1/4”:
1800 lbs pre-drill: 13/64 (.203”)
Pull-out Strength - 55 KSI Yield Sheet Steel
16 ga. (.060”) 637 lbs
pre-drill: 3/16 (.187”)
Notes: Dimensions are nominal unless noted. The specific job conditions should be considered and appropriate safety factors applied when specifyng the proper fasteners.
Selection
Description
TW-S-D12
10-12 x 1
10-12 x 1-1/8
10-12 x 1-1/2
10-12 x 1-3/4
10-12 x 2-3/8
TW-S-D13
12-11 x 1
12-11 x 1-1/8
12-11 x 1-1/2
Part No.
Global Code
0902988
0062661
0625848
0698813
0055443
TW-S-D12-4,8X25
TW-S-D12-4,8X30
TW-S-D12-4,8X38
TW-S-D12-4,8X44
TW-S-D12-4,8X60
0705260
0759330
0705261
TW-S-D13-5,5X25
TW-S-D13-5,5X29
TW-S-D13-5,5X38
Installation
®
™
™
ZAC
MAC
Prisma
irius
Fastener length should provide for
a minimum
of 1”
penetration
into
wood substrate.
Fastener length should provide for a minimum of 3/16” penetration of fully developed threads into
metal substrate. Check with cladding panel manufacturer for specific installation guidelines.
ZAC
MAC
PRISMA
irius
7
3
Options
Painted
Painted
Sentri™
SX
Stainless
Self Drilling
Tools: 0-2500 rpm screwdriver with depth sensing nosepiece.
T20W TORX drive bit.
32
5
6
2
1
4
BI-M
Fastening aluminum composite
panels to aluminum
SLA Self-Drill
• 304 austenitic stainless steel provides the optimum corrosion
resistance performance.
• TORX® T20W drive makes installaton fast and easy.
• Resistant to back out.
• Low profile provides for an aesthetically pleasing façade.
• Custom color matching to your panel is available with scratch
resistant coating
• Resistant to overdrive.
Application
SLA3 Self-Drill
Aluminum composite panels
to aluminum framework
Drilling Capacity (Aluminum): .071”-.118”
Material: 304 Austentic Stainless Steel A2,
material number 1.4301, AISI 304
Drive:
Head Dia:
Dia Nominal:
TORX® T20W
.470”
.190”
Tensile:
Shear:
1765 lbs
1177 lbs
Pull-out Strength
AlMg 1.8 mm (.07l”): 440 lbs
AlMg 2 mm (.079”): 517 lbs
Selection
Description
10-16 x 3/4" SD2
Part No.
1025055
Global Code
SLA3/6 S-D12-4,8X19
Grip Range
0.236"
Installation
0-2500 rpm screwdriver equipped with depth sensing nosepiece.
T20W TORX® drive bit.
irius
Options
Painted
Painted
Sentri™
SX
Stainless
Self Drilling
BI-METAL
irius
3
2
1
4
?
33
SA6/TDA
Panel Fabrication Fasteners
• 304 austenitic stainless steel
• Ensures compatability between fastener, panel and framework
Application
SA6 PHL Pan Head
#10-16 Self-Drill
Drive:
#2 Philips
Head Dia:
.365”
Thread Major Dia:
.182”
Thread Minor Dia:
.134”
Strength (ult.):
Tensile:
1420 lbs
Torsional:
50 in-lbs
Shear:
1270 lbs
Pull-out Strength - Aluminum
.057” Aluminum:
465 lbs
Assembled Shear Strength
1/8” Alum. Bracket to
.057” Alum
687 lbs
Panel to Aluminum
Aluminum to Aluminum
Drilling capacity: Max .118”
Material: 304 Austenitic
Stainless Steel
SA6 PHL Flat Head
#10-16 Self-Drill
Drive:
#2 Philips
Head Dia:
.346”
Thread Major Dia:
.185”
Thread Minor Dia:
.132”
Strength (ult.):
Tensile:
1760 lbs
Torsional:
55 in-lbs
Shear:
1182 lbs
Pull-out Strength - Extruded Aluminum:
1/8” (.125”):
823 lbs
Panel to Aluminum
Aluminum to Aluminum
Drilling capacity: .196-.035”
Stainless Steel
TDA PHL Flat Head
#10 Self-Tapping Type A
Drive:
#2 Philips
Head Dia:
.346”
Thread Major Dia:
.185”
Thread Minor Dia:
.132”
Strength (ult.):
Tensile:
1760 lbs
Torsional:
55 in-lbs
Shear:
1182 lbs
Pull-out Strength - Extruded Aluminum:
1/8” (.125"):
920 lbs
pre-drill #21 (.159”)
Cladding Panel to Metal
Metal to Metal
Stainless Steel
Notes: Dimensions are nominal unless noted. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners.
Selection
Description
SA6 PHL Pan Head
#10 x 3/4"
SA6 PHL Flat Head
#10 x 3/4"
#10 x 1"
TDA PHL Flat Head
#10 x 3/4" Type A
#10 x 1" Type A
Part No.
Global Code
1269126
SA6/6-D9-PH2-4,8X19
1247521
1247449
SA6/6-PH2-4,8X19
SA6/11-PH2-4,8X25
1247525
1247523
TDA-S-PH2-4,8X19
TDA-S-PH2-4,8X25
Installation
Fasteners should provide for a minimum of 3 fully developed threads through the metal substrate.
Tools: 0-2000 rpm screw driver equipped with depth sensing nosepiece.
34
Fastening cladding panels to aluminum
or steel framework
AP Rivet
• Can be used in assemblies of dissimilar materials,
thick and thin, hard and soft, metal, composites and phenolic panels
• Good installed appearance
• Reliable quality and repeatability of assembly
• No over-driving or under-driving
• Available painted to match any panel color
• Tamper resistant
• Won’t loosen in high vibration and fatigue applications
Application
AP16 Rivet
Attach high-performance cladding
panels to aluminum or steel sub-frames
16
(0.63”)
5 (0.19”)
Drilling capacity:
2.7
(0.11”)
Material:
Body: Aluminum AlMg5
Mandrel: Stainless Steel A3
1.5 (0.06”)
Nom. Tensile: 3720 N (836 lbs.)
Nom: Shear: 2410 N (542 lbs.)
Pull-out Strength - Extruded Aluminum
AIMg 1.8mm (.071”): 2410 N (542 lbs)
Pull-out Strength - 33 KSI Yield Sheet Steel
22 ga. (030”): 1210 N (272 lbs.)
18 ga. (.048”): 2360 N (530 lbs.)
Pull-out strength values obtained with 5.1 mm (0.201”) pre-drill.
Selection
Description
5 X 16mm
5 X 18mm
5 X 21 mm
Part No.
0914963
0870920
0994642
Global Code
AP16-50160-S
AP16-50180-S
AP16-50210-S
Grip Range
8.0-12.0 mm (.314-.472")
9.5-13.5 mm (.374-.531")
12.5-16.5 mm (.492-.649")
Installation
5.1mm (0.201”) pilot hole required in aluminum framework for fixed point. All other holes depend on
material. Check the attachment method instructions provided by the cladding panel manufacturer.
irius
Options
Painted
Painted
Sentri™
SX
Stainless
Self Drilling
BI-METAL
irius
3
2
1
4
?
35
TU-S Blind Fastener
• Enables brackets, straps or clips to be attached quickly and
securely to the back of HPL cladding panels
• Cost-effective
Fastening HPL cladding panels
• No special tools required
• Can be installed into panels 8mm to 13mm (.31” to .51”) thick
• Installation can be performed by one person
Application
TU-S Blind Fastener
Fasten brackets, straps or clips
to the back of panels
3.3 (0.13”)
Material:
Sleeve: Stainless steel (grade 316, DIN 1.4401)
6 (0.24”)
8
(0.31”)
Mandrel: Carbon steel (is pulled off
completely, i.e. no residue remains)
Selection
Description
6 X 11mm
6 X 13mm
Part No.
0778444
0848724
Global Code
TU-S-6X11
TU-S-6X13
Bracket Range
0.5-5.5 (0.02-0.21")
2.5-7.5 (0.09-0.29")
Panel Range
8-13 mm (0.31-0.51")
10-13 mm (.039-0.51")
Installation
Pre-drill pilot hole a minimum of 6.5mm deep and 6.0mm diameter. Residual panel thickness must
be at a minimum of 1.5mm; check panel manufacturer’s specific requirements. Insert fastener by
hand through bracket into pre-drilled pilot hole; remove the mandrel with riveting tool.
Utilize HSS blind hole drill bit, 6mm (0.236”) diameter, with depth stop
Bracket or clips requires a 7 mm (0.276”) clearance hole
An appropriate washer is required with thinner brackets.
36
Exposed fastening effects for
cladding attachment
GAZ Design Elements
GAZ Design Elements fasteners are a two-part fastening system. The
304SS anchor secures cladding to timber, steel or aluminum subframes. The design element cap is then effortlessly assembled on to
the special fastener after installation.
• 300 series stainless steels provides maximum corrosion
resistance
• Design elements available in a choice of colors and fascinating
effects
• Creates special emphasis on internal or external surfaces
• Secure against unwinding through dynamic loads. Cannot be
removed manually after curing.
Application
GA #14 Type A Anchor
SW 9.5 (0.38”)
Material:
Fastener: 304SS
Sealing Washer: SS with vulcanized EPDM
6.5 (0.26”)
45 (1.77”)
GA #14 Type B Anchor
SW 9.5 (0.38”)
Material:
Fastener: 304SS
Sealing Washer: SS with vulcanized EPDM
6.3 (0.25”)
32 (1.26”)
GAZ Design Element Caps
Available in 316 Stainless Steel, 303 Stainless Steel
or anodized aluminum
Available in the following colors:
Stainless Steel: Mill finish, 40 maximum surface roughness
Aluminum: red, blue, green, black, gold, silver
801
0.865” x 1.26”
804
0.865” x 1.26”
Selection
Part No.
Description
Anchors
0006132
14 x 1-1/4 Type A Stainless Steel Anchor
0921058
14 x 1-3/4 Type A Stainless Steel Anchor
0920499
14 x 1-1/4 Type B Stainless Steel Anchor
GAZ Design Elements
0974222
Stainless Steel Cap
0984140
Stainless Steel Cap
0920496
Stainless Steel Cap
0920497
Stainless Steel Cap
0974609
Stainless Steel Cap
000000
Anodized Aluminum Cap
000000
000000
000000
000000
Global Code
806
1.24” x 1.50”
811
0.865” x 1.26”
807
1.24” x 1.26”
GA-AS-S16-6,5X32
GA-AS-S16-6,5X45
GA-BS-S16-6,3X32
GAZ-801-S
GAZ-804-S
GAZ-806-S
GAZ-807-S
GAZ-811-S
GAZ-801
GAZ-804
GAZ-806
GAZ-807
GAZ-811
Installation
E395 special socket avaiable.
37
Metal to Wood
Woodgrip, HiLo Woodgrip, Woodgrip XG,
Woodgrip™ Fasteners Woodgrip #14 Type A MP, Low Profile Woodgrip
For metal to wood
Woodgrip is the original sheet to wood fastener designed
to self-drill metal panels:
HiLo Woodgrip is a sheet to wood fastener designed to
self-drill metal panels:
Woodgrip XG is a sheet to wood fastener designed to self
drill metal panels:
Low Profile Woodgrip is a sheet to wood fastener
designed to self-drill metal panels:
• High Hex Washer Head provides driving stability
and a sharp point for quick installation.
• Assembled with a control seal washer for a consistent,
weather tight seal and improved installation appearance.
• Extended corrosion resistant coating system.
• Superior performance in OSB, plywood and 1x4 pine.
• Superior resistance to stripout
• Extra aggresive thread design.
• Improved pullout and backout values over other wood screws
by as much as 30%.
• High Hex Washer Head provides driving stability
and a milled point for quick installation.
• Assembled with a bond seal washer for a consistent, weather
tight seal and improved installation appearance.
• Low profile head for pleasing appearance.
• Mill point ensures great drill performance.
• HiLo thread with added pull-out resistance.
• Available with bond seal for exterior sidewall application or
no washer for interior applications.
Woodgrip # 14 Type A mill point carbon steel
self-tapping fasteners are designed for attaching
both metal to wood and metal to metal:
• These fasteners do not require a pre-drilled hole when
attaching 26 and 24 gage metal to wood.
Application
1/4" Hex Washer Head
Tensile: 1500
Torsional: 60 in-lbs min.
Shear: 933
Woodgrip 9–15 HWH
Sharp Point
Assembled with Control Seal
Metal to wood
Drilling capacity: 24 ga (.024)
Self-drills through the metal panel
and taps into wood substrate.
Min penetration in wood substrates
should be no less than 1"
Tensile: 1500
Shear: 933
HiLo Woodgrip 10 –15
Assembled Bond Seal washer
Metal to wood
Woodgrip XG 12– 8 HWH
Sharp Point
Assembled with Control Seal
Metal to wood
Drilling capacity: 24NEGATIVE
ga (.024)
reduced 00%
and taps into wood substrate. Large,
aggressive thread design provides
superior resistance to strip-out, and
superior performance in OSB, plywood,
and 1x4" pine. Min penetration in wood
substrates should be no less than 1"
Notes
Dimensions are nominal inches unless noted.
File Name: WG6.1_C0261.eps
Tensile: 2183
Shear: 1946
38
Metal to Wood
For metal to wood
Application
Woodgrip 12 x 3/4 Lap
1/4" Hex Washer Head:
Tensile: 2100
Shear: 1800
Assembled Bond Seal washer
Drilling capacity: 2 x 24 ga
Panel to panel side lap, end lap
and other stitch applications
Woodgrip HiLo 10-15 Low Profile
T25 TORX Pan Head:
Tensile: 1500
Shear: 933
Exterior Sidewall Fastener, Bond Seal
Drilling capacity: 24 ga. (.024)
Woodgrip HiLo 10-15 Low Profile
NEGATIVE
00%
Interior Liner Panel,
Noreduced
Washer
Drilling capacity: 24 ga. (.024)
T25 TORX Pan Head:
Tensile: 1500
Shear: 933
Available painted white only.
Tensile: 3500
Shear: 2400
Carbon Steel, Silver Sentri
Metal to wood
Sheet .018 – .030
combined for total.
Notes
39
Metal to Wood
For metal to wood
Performance Pounds Ultimate
Pull-out (lbs ult.)
Wood: Spruce, Pine, Fir
Pull-over
#9 Woodgrip Control Seal Washer
1-1/2" Penetration
1" Penetration
748
542
29 ga (110 ksi): 577
26 ga (70 ksi): 637
24 ga (70 ksi): 800
#10 HiLo Woodgrip Bond Seal Washer
1-1/2" Penetration
1" Penetration
820
524
29 ga (110 ksi): 577
26 ga (70 ksi): 637
#10 HiLo Torx Pan Head Woodgrip
1-1/2" Penetration
1" Penetration
820
524
1" Penetration
29 ga (110 ksi): 577
26 ga (70 ksi): 637
24 ga (70 ksi): 800
1013
22 ga (.030): 1097
24 ga (.024): 810
26 ga (.018): 564
#12 Woodgrip XG Control Seal Washer
SPF 1-1/2" Penetration
SPF 1" Penetration
1x4" Pine
3/4" Plywood
5/8" Plywood
1/2" Plywood
23/32" OSB
19/32" OSB
Pull-out (lbs ult.)
% Increase Strip-out
vs. Woodgrip (in-lbs)
874
571
590
587
446
384
524
456
20
20
34
25
31
39
21
31
Pull-over
29 ga (110 ksi): 577
26 ga (70 ksi): 637
24 ga (70 ksi): 800
Fasteners installed in less than 1" of solid wood may
have an increased potential for sealing or connection
failure over time. This may be due to the fasteners being
stripped out during installation and/or due to the lack
of adequate wood fiber material to hold the fastener in
place during thermal movement cycles or other forces
which may be exerted upon the connection.
Notes: Woodgrip and HiLo pull-out strength values may vary from tested loads depending upon specific wood
density variations. Woodgrip and HiLo pull-over strength values are based on .035" thick, ½" OD Control
Seal or Bond Seal washer and have been updated to reflect common tensile strengths of metal panels as a
function of panel thicknesses.
TORX® pan head HiLo pull-out strength values may vary from tabulated loads depending upon specific
wood density variations. Pull over strength values are based on ½" nominal OD TORX® head and AZ55
Galvalume steel material.
Percent increase strip-out values of the Woodgrip XG over the standard Woodgrip are typical results,
as encountered when fasteners are installed at 2500 rpm until full strip-out occurs.
Ultimate values listed are the result of laboratory testing. The specific job conditions should be
considered and appropriate safety factors applied when specifying the proper fastener.
Selection
Size
1"
1-1/2"
2"
2-1/2"
3"
12 x 3/4" (1/4" HWH)
Woodgrip
V0161-CCF
V0261-CCF
V0381-CCF
V0461-CCF
V0485-CCF
V1701-ECF
Installation
HiLo Woodgrip
V1008-CDF
V1012-CDF
V1016-CDF
V1020-CDF
V1024-CDF
V1707-EAF
ZAC® with
Tools: 0 – 2500 rpm screw driver equipped
depth sensing nose piece.
ZAC
Woodgrip XG
V1806-EMF
V1841-EMF
V1851-EMF
V1856-EMF
V1861-EMF
Exterior Low Profile
A0408-CFF
A0412-CFF
A0416-CFF
—
—
—
MAC™
Prisma™
MAC
PRISMA
Interior Liner Panel
A0308-001F
—
—
—
—
—
Options
irius
VistaCoat™
Painted
Painted
irius
#14 A Milled Point
V3321-GBF
V3438-GBF
V3531-GBF
A3597-GBF
A3626-GBF
—
ZAC
Sentri
®
ZAC
ZAC
®®
ZAC
ZAC
™
Stainless
™™
MAC
Prisma
SX™ ™Self Drilling
BI™
Prisma
MACMAC
MAC
MAC
PRISMA
PRISMA
40
5
7
2
iMetal.net
- 6Phone: 267-983-1017
-3 www.iMetal.net
55 1
66
4
77
Metal to Wood
EVERGRIP® 300 Series
Stainless Fasteners
EVERGRIP stainless bi-metal
For metal to wood
EVERGRIP stainless wood fastener is designed
to self-drill metal panels:
• Head and the majority of shank is 300 Series Stainless Steel, with a
welded, hardened carbon steel point for self-drilling performance.
• Provides the corrosion protection of stainless with the drill
performance of a carbon steel fastener.
• Designed specifically for superior corrosion resistance in all wood
treatments.
• Available with HWH or TORX drive pan head.
Application
EVERGRIP
9 – 15 HWH Sharp Point
Assembled with
stainless Bond Seal
Metal to wood
Thread Major Dia: 0.181 – 0.175
Thread Minor Dia: 0.133 – 0.127
Tensile: 1657
Shear: 1550
Drilling capacity: 24 ga (0.024)
EVERGRIP
9 – 15 T-25 (TORX®) Pan Head
Assembled with
stainless Bond Seal
Metal to wood
Drilling capacity: 24 ga. (0.024)
File Name: P_1481A_E.eps
Created by:EWB-04/8/08
Pull-out (lbs ult.)
EVERGRIP Stainless Bond Seal
1-1/2" Penetration
1" Penetration
Pull-over
748
542
29 ga: 378
26 ga: 519
24 ga: 704
Notes: Dimensions are nominal inches unless noted. Pull out strength values may
vary from tabulated loads depending upon specific wood density variations.
Pull over strength values are based on AZ55 Galvalume steel material.
Ultimate values listed are the result of laboratory testing. The specific job
conditions should be considered and appropriate safety factors applied.
Selection
Length
1"
1-1/2"
2"
2-1/2"
3"
HWH
250/Bag
E4160-CUF
E4260-CUF
E4380-CUF
E4460-CUF
—
Description
SFS Special T-25 Torx drive bit
HWH
100/Box
E4160-CUEG
E4260-CUEG
E4380-CUEG
E4460-CUEG
—
Part No.
0514261
T-25 (TORX) Pan Head
Head Dia: 0.393–0.374”
Thread Major Dia: 0.181 – 0.175
Thread Minor Dia: 0.133 – 0.127
Tensile: 1657
Shear: 1550
Utilizing the special SFS T-25 Torx drive
bit manufactured by SFS intec is
recommended for superior stability
during the installation process.
Fasteners installed in less than 1" of solid wood may have an increased potential
for sealing or connection failure over time. This may be due to the fasteners being
stripped out during installation and/or due to the lack of adequate wood fiber
material to hold the fastener in place during thermal movement cycles or other
forces which may be exerted upon the connection.
Installation
® Pan Head
™ screwdriver equipped
T-25
2500 rpm
ZAC
MAC™ Tools: 0 –Prisma
irius
250/Bag
1119934
ZAC 1124180
1119937
1127014
1119938
5
Quantity
1 each
with depth sensing nosepiece.
The EVERGRIP 9-15 T-25 (TORX) Pan Head
PRISMATorx drive bit. irius
MAC requires a T-25
Utilizing the special SFS T-25 Torx drive
bit manufactured by SFS intec is
recommended for superior stability
during the installation process.
6
7
3
Options
Painted
Painted
Sentri™
1
2
41
SX
Metal to Wood
300 Series Stainless
Aluminum Panel Woodgrip™
Woodgrip stainless
For aluminum panel
Stainless, Aluminum Panel Woodgrip is an all stainless
wood fastener designed for use with aluminum panels:
• Fastener is 304 stainless steel for corrosion protection.
• High hex washer head provides driving stability
and a sharp point for quick installation into aluminum.
• Will not drill steel panels.
Application
Stainless
Aluminum Panel Woodgrip
9 – 15 HWH Sharp Point
1/4" Hex Washer head
Tensile: 1657
Torsional: 50 in-lbs min
Shear: 1550
Assembled with
aluminum Bond Seal
Metal to wood
Self-drills through aluminum panel
Min penetration in wood substrate
should be no lessPOSITIVE
than 1"reduced 00%
Pull-out (lbs ult.)
#9 Woodgrip Stainless Aluminum Bond Seal
1-1/2" Penetration
1" Penetration
748
542
Notes: Dimensions are nominal inches unless noted. Pull out strength values may vary from tabulated loads depending
upon specific wood density variations. The specific job conditions should be considered and appropriate
safety factors applied. Stainless Woodgrips are not designed to self-drill steel panels.
Fasteners installed in less than 1" of solid wood may have an increased potential for sealing or connection failure
over time. This may be due to the fasteners being stripped out during installationFile
and/or
due
to the lack of adequate
Name:
WG6.3_E0270.eps
wood fiber material
to hold
the00%
fastener in place during thermal movement cycles orCreated
other forces
which may be
by: EWB-11/27/02
NEGATIVE
reduced
exerted upon the connection.
Selection
Size
1"
1-1/2"
2"
2-1/2"
3"
Stainless Woodgrip
E0225-CKF
E0270-CKF
E0272-CKF
E0275-CKF
E0277-CKF
Installation
Tools: 0 – 2500 rpm screwdriver equipped
with depth sensing nosepiece.
irius
Options
Painted
Sentri™
2
1
Painted
SX
Stainless
Self Drilling
BI-METAL
irius
3
4
?
42
Metal to Wood
WoodZAC® and WoodMAC™
Woodgrip™ Capped Fasteners
WoodZAC has all the performance features of
standard Woodgrip fasteners, plus a zinc alloy
cap that can never red rust:
• 5/16" AF high Hex Washer Head for driving stability
and a sharp point for quick installation.
• Assembled with a aluminum bond seal for weather tight
seal and improved installation appearance.
For metal to wood
WoodMAC has all the performance features
of standard Woodgrips:
• 1/4" AF 300 series stainless capped HWH for a low profile head
appearance that can never rust.
Application
HiLo WoodZAC
10–15 HWH Mill Point
Zinc Alloy Cap
Tensile: 1500
Shear: 933
Assembled with
aluminum Bond Seal
Metal to wood
WoodZAC XG
12–8 HWH Sharp Point
Zinc Alloy Cap
Tensile: 2183
Shear: 1946
Metal to Wood
WoodZAC
12 x 3/4" LAP Sharp Point
Zinc Alloy Cap
Tensile: 2100
Shear: 1800
Panel to panel side lap, end lap
#14 ZAC Type A
Milled Point
3/8" AF Zinc Alloy Capped
Tensile: 3500
Shear: 2400
Metal to wood
Sheet .018 – .030
combined for total.
Min depth penetration
the
POSITIVEinto
reduced
00%
Notes
43
Metal to Wood
For metal to wood
Application
1/4 ZAC Type AB
Milled Point
3/8" AF Zinc Alloy Capped
Tensile: 3800
Shear: 2500
Metal to metal
Metal to wood
Sheet .018 – .030
POSITIVE reduced
00%
single or multiple material
thickness
combined for total.
WoodMAC POSITIVE reduced 00%
9–15 HWH Sharp Point
1/4" Cupped Stainless Capped
Tensile: 1500
Shear: 933
Metal to wood
File Name: WG6.2_C0268.eps
Created by: MPD-12/02/02
WoodMAC Lap
12 x 3/4" HWH Sharp Point
Assembled EPDM washer
Panel to panel side
lap, end lap
1/4" Cupped Stainless Capped
Tensile: 2100
Shear: 1800
Notes: Dimensions are nominal inches unless noted.
Pull-out (lbs ult.)
Pull-over
#10 HiLo Woodgrip 5/16" ZAC Aluminum Bond Seal
1-1/2" Penetration
1" Penetration
820
524
#9 Woodgrip 1/4" MAC EPDM Washer
1-1/2" Penetration
1" Penetration
748
542
#14 A Milled Point 3/8" ZAC
1" Penetration
1013
1/4" AB Milled Point 3/8" ZAC
1" Penetration
26 ga: 564
24 ga: 810
22 ga: 1097
1013
26 ga: 600
24 ga: 866
22 ga: 1094
29 ga: 577
26 ga: 637
24 ga: 800
29 ga: 380
26 ga: 500
24 ga: 710
44
ma™
SMA
7
Metal to Wood
For metal to wood
Pull-out (lbs ult.)
#12 WoodZAC XG EPDM Washer
SPF 1" Penetration
1 x 4" Pine
3/4" Plywood
5/8" Plywood
1/2" Plywood
23/32" OSB
19/32" OSB
Strip Out* (in lbs)
874
571
590
587
446
384
524
456
79
68
51
65
42
53
76
64
Pull-over
29 ga (110 ksi): 577
26 ga (70 ksi): 637
24 ga (70 ksi): 800
* Strip-out values were determined by the dynamic strip-out test, wherein fasteners were driven though a 24 gage panel into the applicable substrate at 2500 rpm until
stripout occured. The strip-out values listed above represent the average maximum strip-out measured by the digital data acquisition system when the fastener was driven
into the given substrate.
Notes: Woodgrip and WoodZAC pull out strength values may vary from tabulated loads depending upon specific wood density variations. Ultimate values listed are the result of
laboratory testing. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners.
Fasteners installed in less than 1" of solid wood may have an increased potential for sealing or connection failure over time. This may be due to the fasteners being
stripped out during installation and/or due to the lack of adequate wood fiber material to hold the fastener in place during thermal movement cycles or other forces
which may be exerted upon the connection.
Selection
Size
1"
1-1/4"
1-1/2"
2"
2-1/2"
3"
12 x 3/4" ZAC (5/16" HWH)
12 x 3/4" MAC (1/4" HWH)
HiLo WoodZAC
WoodZAC XG
A1066-DNF
—
A1071-DNF
A1076-DNF
A1081-DNF
A1086-DNF
—
—
A1807-FCF
—
A1842-FCF
A1852-FCF
A1857-FCF
A1862-FCF
—
—
WoodZAC
Lap
—
—
—
—
—
—
A1705-FLF
—
WoodMAC
C0168-CAF
—
C0268-CAF
C0388-CAF
C0468-CAF
C0488-CAF
—
—
WoodMAC
Lap
—
—
—
—
—
—
—
A1708-EYF
#14 A Milled Point
3/8" ZAC
A3325-FMF
—
—
—
—
—
—
—
#14 AB Milled Point
3/8" ZAC
A4395-FMF
A4428-FMF
A4485-FMF
A4513-FMF
A4510-FMF
—
—
—
Installation
Tools: Tools: Metal to metal application: 0 – 600 rpm screwdriver equipped with depth sensing nosepiece.
Metal to wood application: 0 – 2500 rpm screwdriver equipped with depth sensing nosepiece.
Options
irius
VistaCoat™
Painted
Painted
Sentri™
SX
Stainless
Self Drilling
BI-METAL
irius
3
2
1
4
?
45
Panelmaster® Fastening System
(RH3) Description:
Collated belted
#3 Phillips
fasteners
Drive
®
(RH2) Product
Panelmaster
Name: #14
• Increased speed of installation
• Improved working ergonomics
• Stand-up roof attachment
(RH4) Application:
For Post Frame
Insulation
Metalboard
PaneltoAttachment
roof cover.
• Fasteners installed uniformly every time
• Special footpieces available for attachment through the panel rib
• Installs fasteners 1"– 3" long
Application
Panelmaster™ Tool Kit
Standard tool kit includes:
– Panelmaster tool
– DeWalt ® 18V drive unit
– Battery charger and extra battery
– One extension piece
– Extra drive bits
– Corded DeWalt drive unit available
– One-year full replacement warranty
Belted Fasteners
– SFS intec fasteners 1" through 3" lengths
with sealing washers
– Can be painted to match any panel color
– All fasteners packaged 500 per carton
Selection
Woodgrip™ Fasteners
Long-Life Fasteners
Item
Length
Woodgrip 9 –15 HWH
Control Seal Washer
VistaCoat
1"
V0161-CCBL
1-1/2"
V0261-CCBL
HiLo Woodgrip 10 –15
HWH Bond Seal Washer
VistaCoat
Woodgrip XG 12 –11 HWH
Bond Seal Washer
VistaCoat
SFS Part #
Item
Length
SFS Part #
WoodMAC 9-15 HWH
Seal Washer
VistaCoat
1"
C0168-CABL
1-1/2"
C0268-CABL
2"
V0381-CCBL
2"
C0388-CABL
2-1/2"
V0461-CCBL
2-1/2"
C0468-CABL
3"
V0485-CCBL
3"
C0488-CABL
1"
V1008-CDBL
1-1/2"
V1012-CDBL
Evergrip 9-15 HWH
Stainless Bond Seal Washer
1"
E4160-CUBL
1-1/2"
E4260-CUBL
2"
V1016-CDBL
2"
E4380-CUBL
2-1/2"
V1020-CDBL
2-1/2"
E4460-CUBL
3"
V1024-CDBL
1"
V1806-EMBL
1-1/2"
V1841-EMBL
2"
V1851-EMBL
2-1/2"
V1856-EMBL
3"
V1861-EMBL
Evergrip 9-15 Torx
Stainless Bond Seal Washer
1"
1110324
2"
1110327
3"
1110329
46
Panel Clips, Bearing Plates and Fasteners
Engineered panel clips
Standing Seam Clips
• Engineered panel clips are custom designed and manufactured
for your panel system.
• Clips are supplied in galvanized steel, coated steel,
stainless steel and other materials.
• Engineered fixed and float clip designs are available.
For standing seam panel attachments
• Standard clips are available from stock without tooling cost to you.
• Sealant can be pre-applied to the clips to maintain the seal
at the clip attachment.
• Clip design options are available for review and evaluation.
• All clips also available in stainless steel.
Application - Snap Lock
Snap Lock Panel Design
Configurations require very low profile
clip bases with a base feature to hold
the panel above the low profile
fastener heads.
Clip
Roof Panel
Roof
Panel
Low Profile
Head Fastener
Blanket
Insulation
Fixed Clips are primarily used with these
panels. Low profile head fasteners should
be used with these panels to provide
clearance for the panel over the fastener
heads. These clips are manufactured from
steel, stainless steel and other materials
with various finishes to fit the needs of the
panel application.
Roof Purlin
Clip
Roof Panel
Roof
Panel
Low Profile
Head Fastener
Blanket
Insulation
Roof Purlin
Selection
1" Snap Lock Clip
1-1/2" Snap Lock Clip
G90 Galvanized: 18 ga.
Packaged 200 per carton
G90 Galvalume: 24 ga.
1-1/2" Snap Lock
1-1/2" Snap Lock Clip
G90 Galvanized: 18 ga. or 20 ga.
1-5/8" Snap Lock
(3 hole) Clip
1-3/4" Snap Lock
(2 hole) Clip
1-3/4" Snap Lock
(1 hole) Clip
1-3/4" Snap Lock
(3 hole) Clip
47
Standing Seam Clips
Application - Snap Lock
BattenTrim (spider)
Clip
304SS (1/4 Hard): 22 ga.
Application - Architectural/Mechanical
Architectural/Mechanical
Panel Design
Configurations require low profile
bases with clearance for the
fastener head.
Sliding Clip
Assembly
Roof
Panel
Roof
Panel
Roof Purlin
Fixed and Float Clips are used with these
panels. The clips may have pre-applied
sealant to maintain the panel seal at the
clip attachment point. These clips are
manufactured from steel, stainless steel
and other materials with various finishes
to fit the needs of the panel application.
Blanket
Insulation
Sliding Clip
Assembly
Roof
Panel
Roof
Panel
Roof Purlin
Blanket
Insulation
Selection
1-1/2" Fixed Clip (.38 Hor.)
2" Fixed Clip (.57 Hor.)
Factory applied sealant
48
Standing Seam Clips
G90 Galvanized: 22 ga. and 24 ga.
1-1/2" Float Clip (.65 Hor.)
G90 Galvanized: 22 ga. Tab
Base: 16 ga.
Base: 16 ga.
2" Float Clip (.57 Hor.)
Base: 16 ga.
Base: 16 ga.
Base: 16 ga.
Base: 16 ga.
Base: 16 ga.
Base: 16 ga.
49
Engineered
panelDrive
clips
(RH3) Description:
#3 Phillips
Standing Seam Clips
For standing
seamboard
panelto
attachments
(RH4) Application:
Insulation
roof cover.
Base: 16 ga.
Base: 16 ga.
Base: 16 ga.
Base: 16 ga.
For 2" Panel
For 3" Panel
Base: 16 ga.
Base: 16 ga.
For 3" Panel
Base: 16 ga.
50
Standing Seam Clips
Butterfly Tab 1-1/2"
Butterfly Base 1-1/2"
Butterfly Tab 2"
Butterfly Base 2"
Continuous Base
1-1/2" or 2"
1-1/2"–G90 Galv.: 22 ga.
1-1/2" Packaged 125 10ft
pieces per carton
2"–G90 Galv.: 18 ga.
2" Packaged 100 10ft
pieces per carton
51
Bearing Plates
Snap Lock and Universal Bearing Plates
• Unique design fits most standing seam clips
• Hole spacings can be customized to meet
customer requirements
• Produced in 16-26 ga. materials
• Available in various dimensions
Application - Bearing Plates
Snap Lock Bearing Plate
Dimension 4.75" x 6"
24 ga. G-90 Galv.
Universal Bearing
Plate
Dimension: 4" x 6"
or 4" x 5"
18, 20, 22 and 24 ga. G-90 Galv.
52
Clip attachment fasteners
Clip Fasteners
• Designed with unique head styles, drill point
configurations and material types to meet performance
requirements to attach standing seam roof clips.
For metal to metal, metal to wood
• Engineered profile features preventing panel
damage from fastener head contact.
• Engineered installation torque drive control
for uniform installation performance.
Application
#10 Type A: Pancake Head
2/2 Quadrex Drive
Carbon Steel, Zinc Plated
Metal to wood
Clip
Head Height: .080 – .068
Head Dia: .447 – .423
Carbon
Tensile:
1825
Torsional:
48 in-lbs
Shear:
1535
#10 Type A, Pull-out (lbs ult.):
SPF wood:
1" penetration: 821
#10 Self Drill, Pull-out (lbs ult.):
12 ga (.105): 1782
14 ga (.075): 1072
16 ga (.060): 782
Roof Panel
Roof
Panel
Phillips Drive
300 Series Stainless Steel
Metal to wood
Low Profile
Head Fastener
Blanket
Insulation
Roof Purlin
#10 Self-Drill: Pancake Head
2/2 Quadrex Drive
Metal to metal
Stainless
1653
50 in-lbs
1587
00%
Min projection: POSITIVE
3/8" ofreduced
threads
below substrate
#12–8 XG Sharp Point: Pancake Head
2/2 Quadrex Drive
Carbon Steel , Zinc Plated
Metal to wood
Head Dia: .447 – .423
Thread Major Dia: .215 –.209
Thread Minor Dia: .133–.127
Tensile: 2183
Shear: 1946
Performance (lbs ult.): Pull-out
874
SPF 1" Penetration
571
1x4" Pine
590
3/4" Plywood
587
5/8" Plywood
446
1/2" Plywood
384
23/32" OSB
524
19/32" OSB
456
2/2 Quadrex Drive
Head Dia: .447 – .423
Tensile: 1940
Shear: 1805
SPF wood:
1" penetration: 724
#12 Self-Drill:
Pancake Head
2/2 Quadrex Drive
Head Dia: .447 – .423
Tensile: 2900
Shear: 2050
12 ga (.105): 1539
14 ga (.075): 1010
16 ga (.060): 724
Metal to wood
Metal to metal
below substrate .
53
iMetal.net - Phone: 267-983-1017
- www.iMetal.net
Panel Clips and Fasteners
Clip attachment fasteners
Clip Fasteners
For metal to metal, metal to wood
Application
1/4 -14 #2 Point
Drilling capacity (#2 point): .050 – .150
Attachment thickness:
combined for total.
Min projection: 3/8"
of threads
POSITIVE
reduced 00%
below substrate
Roof
Panel
Clip
Roof
Panel
Tensile: 3800
Shear: 2850
#2 Point, Pull-out (lbs ult.):
12 ga (.105): 2088
14 ga (.075): 1312
16 ga (.060): 903
Roof
Panel
Roof Purlin
Blanket
Insulation
12-24 #5 Point: Pancake Head
2/2 Quadrex Drive
Head Dia: .447 – .423
Tensile: 3450
Shear: 2420
12 ga (.105): 1378
Metal to metal
Attachment thickness:
combined for total.
Min projection: 3/8” of threads
below substrate NEGATIVE reduced 00%
File Name: WG(7.2)_S5271_14_14Impax.eps
Notes
Dimensions are nominal inches unless noted. Pull-out values (pounds ultimate) are based on 50,000 psi hot rolled steel sheet material. Ultimate values listed are the result of
laboratory testing. The specific job conditions should be considered and appropriate safety factors applied when specifying the proper fasteners.
Fasteners installed in less than 1" of solid wood may have an increased potential for a connection failure over time. This may be due to the fasteners being stripped out during
installation and/or due to the lack of adequate wood fiber material to hold the fastener in place when forces are exerted upon the connection.
Selection
Length
#10 Type A
Pancake
Carbon Steel
1"
1-1/4"
1-1/2"
2"
A1191F
—
A1351F
A1391F
#10 Type A
Pancake
#10 Self-Drill
Stainless Steel
Pancake
E0235F
—
—
E0271F
S3431F
—
S4221F
S4421F
#12–8 XG
Pancake
#12 Type A
Pancake
#12 Self-Drill
Pancake
12–24 #5 Point
Pancake
1/4–14 #2 Point
5/16 AF HWH
1/4–14 #2 Point
3/8 AF HWH
A1900F
—
A1940F
A1950F
A1710F
—
—
—
S4552F
—
—
—
—
—
S4750F
—
—
S5191F
S5286F
—
S5171F
—
S5271F
—
Installation
Tools: 2000 – 2500 rpm #10 self drill, 0 – 2000 rpm on 1/4-14 self drill screwdriver equipped with depth sensing nosepiece.
54
Attachment Solution for
Standing Seam Roofs
AceClamp®
• Fast - No assembly required
• Easy - One top-mount fastener
• Secure - Locks in place
Attachment Solution for:
• solar
• HVAC
• snowrails
• conduit
• windclamps
• signs
Application
AceClamp® ML
3.00”
Fits Mechanical Lock panels
2.06”
0.90”
1.437”
0.50”
0.625”
0.812”
Single Lock
Double Lock
T-Seam
Z-Rib
AceClamp® SL
2.60”
Fits - Snaplock panels
- Mechanical Lock panels
with seam dimension
of ≤ .500"
0.97”
1.91” 0.50”
Snaplock
0.58”
Mechanical Lock
(small seam)
Notes
AceClamp® is not designed for use on batten seam panel systems and is not recommended for nail flange panel systems.
AceClamp® is not to be used as any part of a fall protection system.
For all applications, determining the suitability of the product and the installation orientation relative to the seam are the responsibility of the professional design engineer.
Selection
Model
AceClamp® ML
AceClamp® SL
Drive Bit
Part #
1287430
1287441
1287429
Packaging
20 per box/5 boxes per case
20 per box/5 boxes per case
-
Installation
Tools: 1/4" hex driver (bit #1287429). Finish tightening with calibrated torque wrench.
55
Solar Fastening System
for exposed fastener metal roofs
SOL-R
Fast, Easy, Secure
• Installs quickly
• Rapid adjustment
• UV resistant, corrosion-free
• Eliminates conductivity
Specifications
SOL-R
Material
1.65"
• System components of metal substitute
Polyphthalamide (PPA) with 50% glass
fiber reinforcement
• A2/AISI 304 stainless steel bolt for
height and position adjustment
• Aluminum reinforcement plates on the
base plate
• Pre-assembled butyl sealant on the
base plate
.3"
Docking device
1.18"
Dimensions
Cap
4.8"
.53"
.7"
1.6"
min. height 2.5"
max. height 4.5"
Base plate
flexible
height adjustment
2"
4.41"
Values based on central fastenings
Test result is valid for the whole range of the setting position.
3765N
327N

Shear strength Qb
Test results refer to the ultimate load required for the
component to break when stressed in shear.
The force F is applied on the contact surfaces of the component.
F




x = arithmetical mean value
x = 387 lb
s = 23 lb
x = 505 lb
s = 15 lb
F


x = 846 lb
s = 73 lb

 
F
Tensile strength Zb
component to break when stressed in tension.
 
Compression strength Db
component to break when stressed in compression.
2248N
68N
If the SOL-R docking device is placed in a vertical position,
calculate with the following values:
1724N
104N
s = standard deviation
Db
x = 364 lb
s = 29 lb
1621N
130N
Zb
x = 346 lb
s = 20 lb
1543N
89N
Qb
x = 346 lb
s = 20 lb
1543N
89N
Notes
All calculations, measurements, fasteners and design methods have to be verified by a responsible designer or an engineer,
regarding the corresponding structure and loads. Please consult local, regional and national codes and approval requirements.
Selection
Description
SOL-R
Part #
1246887
Packaging
50 units/case
56
(RH3) Blind
Description:
#3 Phillips
rivets attach
light Drive
gage
(RH2) ProductBlind
Name:
Rivets
#14
(RH4) Application: Insulation board to roof cover.
• Many corrosion resistant options
• Tamper resistant
• Won't loosen in high vibration or fatigue applications
• Quality and repeartability of assembly
• No over-driving or under-driving
• The installed function of the rivet will be consistent and is independent of the installer's technique
• Easy to use, lightweight portable installation tools
Selection
BULB-TITE® Rivets
BULB-TITE rivets were first developed to solve application requirements in the Pre-Engineered Metal Building industry.
Since that time the BULB-TITE product line has been expanded to meet application requirements in a wide range of
industries. The BULB-TITE rivet body folds into three seperate legs forming a large blind-side head. This large bearing
head evenly distributes the BULB-TITE's clamp force in soft, thin or brittle materials while providing high pull-through
resistance. The BULB-TITE's wide grip range enables a single BULB-TITE to work in a greater variation of thicknesses.
Aluminum Rivet/Aluminum Mandrel
Head Style
Dome Head Protruding Crown
Large Flange Prot. Crown
Dome Head Recessed Crown
Rivet Diameter
5/32"
5/32"
3/16"
3/16"
3/16"
3/16"
3/16"
3/16"
3/16"
3/16"
3/16"
1/4"
1/4"
1/4"
1/4"
9/32"
9/32"
9/32"
9/32"
9/32"
9/32"
3/16"
3/16"
3/16"
3/16"
3/16"
3/16"
3/16"
3/16"
3/16"
1/4"
1/4"
1/4"
1/4"
Part No.
No Washer
1194602
1194604
1194606
1194608
1194620
1194622
1194624
1194626
1242652
1242654
1242656
1194628
1194630
1194632
1194634
1194718
1194720
1194722
1194724
1194726
1194728
1242668
1242670
1242692
1242694
1242697
1242733
1242767
1242770
1242773
1242781
1242795
1242839
1242868
Part No.
w/ Washer
1194603
1194605
1194607
1194609
1194621
1194623
1194625
1194627
1242653
1242655
1242657
1194629
1194631
1194633
1194635
1194719
1194721
1194723
1194725
1194727
1194730
1242669
1242680
1242693
1242695
1242698
1242735
1242768
1242771
1242774
1242792
1242796
1242841
1242870
Grip Range
.067-.250
.250-.500
.050-.187
.062-.250
.187-.375
.312-.500
.437-.625
.563-.750
.687-.875
.812-1.000
.937-1.125
.062-.250
.125-.375
.250-.500
.375-.625
.032-.375
.250-.625
.375-.750
.042-.375
.250-.625
.375-.750
.050-.187
.062-.250
.187-.375
.312-.500
.437-.625
.563-.750
.687-.875
.812-1.000
.937-1.125
.040-.250
.125-.375
.250-.500
.375-.625
Pre-Drill Hole Size
#20 (.162-.167)
#20 (.162-.167)
#4 (.209-.221)
#4 (.209-.221)
#4 (.209-.221)
#4 (.209-.221)
#4 (.209-.221)
#4 (.209-.221)
#4 (.209-.221)
#4 (.209-.221)
#4 (.209-.221)
1/4 (.250-.263)
1/4 (.250-.263)
1/4 (.250-.263)
1/4 (.250-.263)
5/16 (.304-.3125)
5/16 (.304-.3125)
5/16 (.304-.3125)
5/16 (.308-.327)
5/16 (.308-.327)
5/16 (.308-.327)
#4 (.209-.221)
#4 (.209-.221)
#4 (.209-.221)
#4 (.209-.221)
#4 (.209-.221)
#4 (.209-.221)
#4 (.209-.221)
#4 (.209-.221)
#4 (.209-.221)
1/4 (.250-.263)
1/4 (.250-.263)
1/4 (.250-.263)
1/4 (.250-.263)
57
Blind Rivets
Blind rivets attach light gage
Selection
MEGA GRIP® Rivets
The MEGA GRIP is a high strength structural blind rivet offering several advantages over conventional blind
rivets. MEGA GRIP's wide grip range enables a single MEGA GRIP to replace up to five different lengths of
standard rivets. High shear strength is achieved by MEGA GRIP's flush break self plugging mandrel.
MEGA GRIP rivets are hole-filling, resulting in tighter joints and improved sealing for weather resistance.
MEGA GRIP rivets are installed via standard rivet tools and do not require special nose tips.
Head Style
Dome
Dome
Dome
Dome
Countersunk
Countersunk
Countersunk
Countersunk
Large Flange
Large Flange
Large Flange
Large Flange
Rivet Diameter
3/16"
3/16"
1/4"
1/4"
3/16"
3/16"
1/4"
1/4"
3/16"
3/16"
1/4"
1/4"
Part No.
1194560
1194561
1194562
1194567
1242624
1216216
1242625
1242626
1242631
1242642
1242628
1242630
Grip Range
.062-.250
.062-.437
.080-.375
.080-.625
.125-.312
.275-.500
.125-.437
.125-.625
.062-.250
.062-.437
.080-.375
.080-.625
Pre-Drill Hole Size
#8 (.194-.204)
#8 (.194-.204)
G (.259-.272)
G (.259-.272)
#8 (.194-.204)
#8 (.194-.204)
G (.259-.272)
G (.259-.272)
#8 (.194-.204)
#8 (.194-.204)
G (.259-.272)
G (.259-.272)
Extra Length Metric Rivets
SFS intec supplies a complete line of metric blind rivets according to DIN7337 standards in 3mm, 4mm
and 5mm diameters. Standard material is Aluminum/Steel. Stainless Steel 304 and 316 alloys are
available upon special request. All dimensions for Metric Series are given in millimeters. Additional
diameters of 4.8mm, 6mm and 6.4mm available on special request.
Aluminum Rivet/Steel Mandrel
Head Style
Dome
Dome
Dome
Dome
Dome
Dome
Dome
Dome
Dome
Dome
Dome
Dome
Dome
Dome
Dome
Dome
Dome
Dome
Dome
Rivet Diameter
3mm
3mm
3mm
3mm
4mm
4mm
4mm
4mm
4mm
4mm
5mm
5mm
5mm
5mm
5mm
5mm
5mm
5mm
5mm
Part No.
1194509
1194531
1194532
1194534
1194535
1194536
1194537
1194538
1194539
1194540
1194541
1194542
1194543
1194544
1194545
1194546
1194547
1194549
1194550
Grip Range
13-15
15-17
17-22
22-25
12.5-14.5
14.5-16.5
16.5-21.5
21.5-26
26-30
30-35
25-30
30-35
35-40
40-45
45-48
48-52
52-57
57-62
62-72
Pre-Drill Hole Size
3.1
3.1
3.1
3.1
4.1
4.1
4.1
4.1
4.1
4.1
5.1
5.1
5.1
5.1
5.1
5.1
5.1
5.1
5.1
58
Blind Rivets
Selection
PolyGrip® Multigrip Blind Rivets
PolyGrip rivets feature a wide grip range, enabling a single PolyGrip to replace up to three different
lengths of standard blind rivets. PolyGrip rivets expand radially, filling the application hole, resulting
in tighter joints and improved sealing. The PolyGrip's locked mandrel core creates a weather resistant
fastener. Improved material support is provided by the PolyGrip's larger blindside head formation. Large
flange head style available upon request.
Stainless Rivet/Stainless Mandrel
Head Style
Dome
Dome
Dome
Dome
Dome
Dome
Dome
Dome
Dome
Rivet Diameter
1/8"
1/8"
1/8"
5/32"
5/32"
5/32"
3/16"
3/16"
3/16"
Part No.
1194553
1194555
1194558
1194559
1194580
1194581
1194582
1194583
1194584
Grip Range
.020-.192
.059-.256
.118-.315
.020-.256
.139-.354
.276-.472
.039-.236
.197-.394
.315-.472
Pre-Drill Hole Size
#30 (.128-.133)
#30 (.128-.133)
#30 (.128-.133)
#20 (.161-.166)
#20 (.161-.166)
#20 (.161-.166)
#10 (.193-.199)
#10 (.193-.199)
#10 (.193-.199)
Grip Range
.039-.197
.059-.256
.118-.315
.039-.256
.138-.375
.276-.512
.039-.256
.177-.433
.256-.512
.433-.768
.630-.945
Pre-Drill Hole Size
#30 (.130-.136)
#30 (.130-.136)
#30 (.130-.136)
#20 (.161-.166)
#20 (.161-.166)
#20 (.161-.166)
#10 (.193-.199)
#10 (.193-.199)
#10 (.193-.199)
#10 (.193-.199)
#10 (.193-.199)
Aluminum Rivet/Stainless Mandrel
Head Style
Dome
Dome
Dome
Dome
Dome
Dome
Dome
Dome
Dome
Dome
Dome
Rivet Diameter
1/8"
1/8"
1/8"
5/32"
5/32"
5/32"
3/16"
3/16"
3/16"
3/16"
3/16"
Part No.
1194585
1194586
1194587
1194589
1194610
1194611
1194612
1194613
1194614
1194615
1194616
59
Blind Rivets
Selection
American Standard Blind Rivets
Standard blind rivets are ideally suited for metal trim applications and other light gauge installations.
SFS intec provides a selection of 1/8" diameter rivets painted to match standard industry colors.
Other sizes and colors available upon request.
Head Style Rivet Diameter
Dome
1/8"
Dome
1/8"
Dome
1/8"
Dome
1/8"
Dome
1/8"
Dome
5/32"
Dome
5/32"
Dome
5/32"
Dome
5/32"
Dome
3/16"
Dome
3/16"
Dome
3/16"
Dome
3/16"
Dome
3/16"
Dome
3/16"
Dome
3/16"
Dome
3/16"
Countersunk
1/8"
Countersunk
1/8"
Countersunk
1/8"
Countersunk
1/8"
Countersunk
5/32"
Countersunk
5/32"
Countersunk
3/16"
US Dimension
42
43
44
46
48
52
54
56
58
62
64
66
68
610
612
614
616
42
43
44
45
54
56
64
Part No.
L0500
L0520
L0540
1242922
1242926
L0620
L0660
1242929
1242934
1242935
1242937
L0760
1242939
1242940
1242941
1242943
1242944
1242950
1242951
1242952
1242953
1242954
1242955
1242956
Grip Range
.063-.125
.126-.187
.188-.250
.313-.375
.376-.500
.020-.125
.188-.250
.251-.375
.376-.500
.020-.125
.126-.250
.251-.375
.376-.500
.501-.625
.626-.750
.751-.875
.876-1.00
.092-.125
.126-.187
.188-.250
.251-.312
.188-.250
.251-.375
.188-.250
Pre-Drill Hole Size
#30 (.129-.133)
#30 (.129-.133)
#30 (.129-.133)
#30 (.129-.133)
#30 (.129-.133)
#20 (.160-.164)
#20 (.160-.164)
#20 (.160-.164)
#20 (.160-.164)
#11 (.192-.196)
#11 (.192-.196)
#11 (.192-.196)
#11 (.192-.196)
#11 (.192-.196)
#11 (.192-.196)
#11 (.192-.196)
#11 (.192-.196)
#30 (.129-.133)
#30 (.129-.133)
#30 (.129-.133)
#30 (.129-.133)
#20 (.160-.164)
#20 (.160-.164)
#11 (.192-.196)
US Dimension
42
43
44
Part No.
L0100
L0120
L0140
Grip Range
.063-.125
.126-.187
.188-.250
Pre-Drill Hole Size
#30 (.129-.133)
#30 (.129-.133)
#30 (.129-.133)
Part No.
L1280
L1290
L1300
L1320
1243078
1243079
1243093
1243097
L1485
1243098
1243100
1243104
Grip Range
.063-.125
.126-.187
.188-.250
.251-.375
.376-.500
.020-.125
.126-.250
.251-.375
.020-.125
.126-.250
.251-.375
.375-.500
Pre-Drill Hole Size
#30 (.129-.133)
#30 (.129-.133)
#30 (.129-.133)
#30 (.129-.133)
#30 (.129-.133)
#20 (.160-.164)
#20 (.160-.164)
#20 (.160-.164)
#11 (.192-.196)
#11 (.192-.196)
#11 (.192-.196)
#11 (.192-.196)
Steel Rivet/Steel Mandrel
Head Style
Dome
Dome
Dome
Rivet Diameter
1/8"
1/8"
1/8"
Stainless Rivet/Stainless Mandrel
Head Style
Dome
Dome
Dome
Dome
Dome
Dome
Dome
Dome
Dome
Dome
Dome
Dome
Rivet Diameter
1/8"
1/8"
1/8"
1/8"
1/8"
5/32"
5/32"
5/32"
3/16"
3/16"
3/16"
3/16"
US Dimension
42
43
44
46
48
52
54
56
62
64
66
68
White
001 White
014 Bright White
330 Warm White
348 Bone White
818 Sierra White
Tan
020 Tan
Beige
109 Sand Beige
248 Light Stone
415 Beige
422 Taupe
548 Ivory
Brown
110 Brown
230 Desert Brown
374 Dark Brown
Green
052 Teal Green
228 Green
232 Evergreen
385 Patina
660 Hemlock
732 Denali Green
798 Hartford Green
925 Classic Green
Red
074 Colonial Red
102 Crimson Red
393 Burgundy
691 Barn Red
890 Red
928 Terra Cotta
Bronze
042 Burnished Slate
324 Dark Bronze
537 Medium Brown
Blue
012 Blue
421 Navy
432 Blue Teal
843 Regal Blue
Gray
051 Charcoal Gray
091 Zinc Gray
302 Pearl Gray
416 Slate Gray
578 Old Town Gray
696 Pewter Gray
850 Ash Gray
Black
023 Black
507 Matte Black
Metallic
1160 Champagne Metallic
1161 Silver Metallic
1162 Zactique Metallic
1116 Copper Penny Metallic
60
Blind Rivet Tools
Installation Tools for Blind Rivets
Application
AccuBird
Weight: 4.8 lbs. (2.2 kg)
Working Stroke: .79" (20 mm)
Traction Power: 1,900 lbs. (6,500 N)
Power Pack: 14.4 Volt, rechargeable Li-Ion / 1.3 Ah
Part Number: 0836102
Battery Charger: 110V/60Hz, 60 minute charge time
PowerBird
Weight: 4.8 lbs. (2.2 kg)
Working Stroke: .79" (20 mm)
Traction Power: 2,900 lbs. (13,000 N)
Power Pack: 14.4 Volt, rechargeable Li-Ion / 2.6 Ah
Battery Charger: 110V/60Hz, 60 minute charge time
RV74G
Work Capacity: 5/32", 3/16", 1/4" & 9/32"
BULB-TITE Rivets*
*Requires appropriate sized RV8840 series
BULB-TITE pulling head.
Weight: 6.5 lbs. w/ pulling head attached
Length: 14" w/o pulling head, 18" w/ pulling head attached
Traction Power: 3,000 lbs.
Work Stroke: Continuous reciprocating .375" per cycle
14.4 Volt Cordless Riveting Tool
14.4 Volt Cordless Riveting Tool
Electric (AC) Powered BULB-TITE Tool
• The RV74G is the newest refinement in GESIPA
Electric Powered BULB-TITE installation tool that
is designed for Metal Building Construction
applications. This tool is suited to sidewall panel
applications. Attaching the optional 74-EXT
extension adapts the RV74G for installing
BULB-TITE's in roofing applications from a
standing position.
RV 74-EXT
Weight: 1.5 lbs.
Length: 12-13/16" (Extends tool by 12")
Pulling Head Extension Unit
• Attachment of the 74 EXT extension unit adapts
the RV74G tool for roofing applications. This
ergonomic feature enables BULB-TITE installation
while standing.
BULB-TITE Pulling Heads
Weight: 0.5 lbs.
Length: 6 1/16"
Part Number: 1195150 - Pulling Head - 5/32" Dia.
1195151 - Pulling Head - 3/16" Dia.
RV8840-X (5,6,8,9 Diameter BULB-TITE Rivets)
• RV8840 series pulling heads are designed for use
with 6603, 8604, 8605 series BULB-TITE rivets
which feature multi-grip type mandrels.
• These heads are equipped with jaws and tips for
specific diameter BULB-TITE rivets. The special
BULB-TITE crown-swaging nose tip pivots to align
the tip onto the BULB-TITE rivet's head crown for
improved bore sealing of installed rivets.
RV24RE
Specify the BULB-TITE rivet
diameter when ordering.
Designed for use with Aluminum BULB-TITE rivets, the
tool greatly simplifies rivet removal in repair operations.
The specially ground jaws cut rivet heads off cleanly
without damage to the application material.
BULB-TITE Removal Tool
61
Blind Rivet Tools
Installation Tools for Blind Rivets
Application
Taurus 1
Hydro-pneumatic Power Riveting Tool
• Nose tips for each rivet diameter are stored in
tool's base.
• Same hydraulic section as the Taurus 2 ensures
long tool life and reduced maintenance.
• Suspension loop retracts into tool body.
Taurus 2
• New 3-piece jaw design increases jaw life –
reducing service costs.
• Integrated mandrel collection system with grip
release shutoff – conserves compressed air
resources.
• Padded ergonomic tool grip enhances comfort –
lowers operator fatigue.
Taurus 3
• Taurus 3 is up to 40% lighter than comparable
tools in this power range.
• Long working stroke installs multi-grip rivets in a
single stroke.
• Reliable exhaust-air mandrel ejection with large
collector and saftey interlock.
Work Capacity: 1/8" ø in all materials
Weight: 2.87 lbs.
Pulling Strength: 1,150 lbs. @ 90 psi
Working Stroke: .590 in.
Work Capacity: Up to 3/16" ø in all materials
Weight: 3.75 lbs.
Work Capacity: Up to 1/4" ø in all materials and
9/32" Alum BT
Weight: 4.19 lbs.
Taurus 4
• Taurus 4 offers the high pulling force required for
many of today's 1/4" diameter structural blind rivets.
Work Capacity: Up to 1/4" ø structural blind rivets and
9/32" Alum BT
Weight: 4.4 lbs.
62
Grommet Fasteners
Grommet fasteners attach fiberglass panels
• Allow for one side attachment of fiberglass panels through a pre-drilled hole.
• Designed to pull fiberglass panels together without cracking the material.
• Come assembled with EPDM washers for a weather tight seal.
Application
Grommet Fasteners
Materials:
Neoprene rubber
w/ molded brass nut
Size 3/8" Grommet:
Part No. E0260-CS
Fastener:
10-32 x 1-1/4" stainless
5/16" AF Hex Head
Washer:
15 mm O.D stainless Bond Seal
Size 1/4" Grommet:
Part No. E0080-CU
Fastener:
6-32 x 1-1/4" stainless
1/4" AF Hex Head
Washer:
12 mm O.D stainless Bond Seal
Notes
irius
Options
Painted
Painted
Sentri™
SX
Stainless
Self Drilling
BI-METAL
irius
3
2
1
4
?
63
Closure and Venting Products
WG-7 closure and WG-7 adhesive closure
WG-7™ Closure
• The industry standard for closure material — time testedmillions of feet installed over the last 30-plus years.
• Polyethylene foam for exceptional strength
and compressibility.
• Available with adhesive applied to the contact side of the
panel surface assures positive positioning during installation.
For panel opening filler
• Resist damaging ultra violet rays and ozone deterioration.
• Over 1800 panel configurations available.
• Manufactured in multiple plants for quick delivery.
Application
WG-7 Closure
Material Thickness: 1", 1-1/2", 2"
Color: Black
Typical Inside Closure Application
Typical Outside Closure Application
Technical Properties
Test
Test Method
Units
Values
Density
ASTM D3575
lb/ft³
Internal
°F
ASTM D3575
psi
ASTM D3575
ASTM D3575
ASTM D3575
ASTM D3575
FMVSS302
ASTM D2240
% max
psi
psi
%
4"/min
OO
1.7 - 1.9
194 max
-76 min
5.1
13.6
15
6
11.5
46.8
165
Pass
55
Working Temperature Range
Compression Deflection
Compression Set
Tear Strength
Tensile Strength
Elongation
Flammability
Shore Hardness
25%
50%
25% - 1/2 hr
25% - 24 hr
*Data represents typical values measured on 0.4" thick specimen and should be considered as a guidline only.
64
Pipe Flashing
• Pipe opening can be easily customized on job sight
utilizing clearly marked pipe diameters on each flashing.
• EPDM and Silicone are both flexible materials, resistant
to ultraviolet rays, cracking or weathering.
• Available in EPDM black or gray and silicone red.
Application
Square and round base pipe flashing
For roof pipe flashing
• The aluminum base is corrosion resistant and conforms
easily to any panel configuration or roof pitch.
• Retrofit flashing is available for piping with welded caps
or cross bars.
• Colors available in standard square and round base pipe
flashing.
Square Base
Size
1
2
3
4
5
6
7
8
9
10
Pipe size
1/4 – 2 -3/4"
7/8 – 4"
1/4 – 5-3/4"
2-3/4 – 7"
4 – 8-1/4"
4-3/4 – 10"
5-1/2 – 11"
6-3/4 – 13-1/2"
9-1/2 – 20-1/2"
12 – 28-1/2"
Base size
4-1/2"
6"
8"
10"
11"
12"
14"
17"
25"
34"
Pipe size
1/4 – 2-1/2"
1-3/4 – 3"
1/4 – 5"
3 – 6-1/4"
4-1/4 – 7-3/4"
5 – 9"
6 – 11"
7 – 13"
9 – 19"
Base Size
4-3/4"
6-1/4"
7-3/4"
9-1/4"
10-3/4"
12-1/4"
14-1/4"
16-1/2"
25-1/2"
Closed Top
Closed Top
Round Base
Size
1
2
3
4
5
6
7
8
9
Closed Top
Closed Top
Retrofit Square Base
Size
1
2
3
Pipe size
1/2 – 4"
4 – 9-1/4"
9-1/4 – 16-1/4"
Base Size
8-3/16"
14-1/4"
21-1/2"
Retrofit Round Base Zipper
Size
1
2
3
Pipe size
3/4 – 2-3/4"
2 – 7-1/4"
3-1/4 – 10"
Base Size
4-3/4"
10-3/4"
25-1/4"
65
Pipe Flashing
Square and round base pipe flashing
For roof pipe flashing
Application
Multi-Flash Square Base
Size
3
5
8
MAXI
Standard Pipe size
1/4 – 5 -3/4"
4 – 8-1/4"
6-3/4 – 13-1/2"
12 – 28-1/2"
Retrofit Pipe size
2 – 4-1/2"
3-1/2 – 6-3/4"
6-1/2 – 12"
13 – 27"
Material Specifications
Test Type
Advance ozone resistance
test @ 500 pphm
High temperature:
Intermittent
Continuous
Low temperature:
Resistance tested to
Tensile strength
EPDM
Silicone (Hi-Temp)
70 Hrs.
70 Hrs.
+275º F
+212º F
+500º F
+437º F
-65º F
1450 psi
-100º F
700 psi
Options
Colors Available
66
Metal roofing ridge vent
ProfileVent®
in a roll
• 40 year limited warranty
• Prevents insect infiltration
• Glue spots prevent slipping
during installation
• Prevents snow infiltration
• Fits under any ridge cap
• Meets all model building codes
• Provides proven roof ventilation
• Fits any pitch 2:12 – 20:12
• Packing in English, French
and Spanish
• One person roll-out installation
• Won’t scratch panel finish
• No waste—use leftovers
on next job
• Won’t crack, dent or rust during
shipping or installation
• Will not support a flame
• Won’t clog from airborne dust
• Made in U.S.A.
Application
ProfileVent Rolls
New or re-roof on Purlin
or wood deck Construction:
Use a 2" opening at the ridge
to provide ventilation. On new
or re-roof wood deck construction,
cut a 2" slot at the ridge (1" each side,
start cut 6" from gable ends).
On purlin construction position panels
to leave a 2" opening.
Available in convenient sizes
• 20' package
• 50' package
• 100' package
1
Allow 2" opening at ridge for
ventilation. ProfileVent is rolled
out along the ridge, gable to gable,
about 1" up-slope from the ridge cap
edge. The positioning adhesive on
most profiles will hold ProfileVent in
position and allow for repositioning.
2
ProfileVent can be cut with
scissors or utility knife.
Inset: When splicing ProfileVent,
make the splice at the center top of
the high rib and use caulk or sealant
along the splice.
3
Screw down or pop rivet the ridge
cap according to manufacturer’s
instructions (works with any ridge cap).
Current panel profiles
3/4" Hi-Rib
R-Panel
ProfileVent matches most major OEM profiles.
Call for Details.
67
Metal roofing ridge vent
ProfileVent®
in a stick
• For 3/4" Hi-Rib roofs
• Cut to fit profile
• 1" deep x 2" wide x 3' length
• Won’t dry out from exposure
• Installs just like closure
• 24 pieces/carton — 72 linear
feet
• No release paper
• New improved adhesive
Application
ProfileVent 3' Stick
New or re-roof on Purlin
or wood deck Construction:
Use a 2" opening at the ridge
to provide ventilation. On new
or re-roof wood deck construction,
cut a 2" slot at the ridge (1" each side,
start cut 6" from gable ends).
On purlin construction position panels
to leave a 2" opening.
1
Allow 2" opening at ridge for
ventilation. ProfileVent is
positioned along the ridge, gable to
gable, about 1" up-slope from the ridge
cap edge. The positioning adhesive on
most profiles will hold ProfileVent in
position and allow for repositioning.
2
ProfileVent can be cut with
scissors or utility knife.
Inset: When splicing ProfileVent,
make the splice at the center top of
the high rib and use caulk or sealant
along the splice.
3
Screw down or pop rivet the ridge
cap according to manufacturer’s
instructions (works with any ridge cap).
Current panel profiles
3/4" Hi Rib
68
Ventco™ Ridge Cap Anchor Clip
Ridge cap anchor clip
Anchor clips are recommended in high wind areas and on panels with major ribs 16" on center or greater.
M9002
3/4" Anchor Clip
M9004
1" Anchor Clip
M9006
1-1/4" Anchor Clip
M9008
1-1/2" Anchor Clip
M9010
1-3/4" Anchor Clip
M9012
2-1/2" Anchor Clip
Application
Ventco™ Ridge Cap Anchor Clip
An independent engineering corporation tested the performance
of the Ventco Ridge Cap Anchor Clip under high wind loading.
During testing, a roof/ridge vent/cap system was subjected to wind
speeds that follow the Dade County Test protocol.
The following observations were made concerning the
performance and structural integrity of the clip and ridge cap:
• No lifting of the ridge cap up to 115 mph
• No fastener pull out or loosening
• The ridge cap remained in contact with ventilation system
• No difference in performance when the cap is secured
to the clip with screws or rivets
Specifications
• 20 gauge galvanized steel
• Visible surface painted black for aesthetic purposes
1
Install your metal roofing panel
according to manufacturer’s
instructions. Apply mastic above and
below pre-drilled holes in the clip.
Before installing ProfileVent ®, insert
#14A screw through the large downslope access hole in top of the Ridge
Cap Anchor Clip.
2
Lift the back end of clip. Slip
ProfileVent under the clip. Push
clip back down and insert another
#14A screw in the up-slope hole.
Packaging
• 25 clips per small box
• 24 small boxes per master box
• 600 clips per master box
Anchor Clip Detail
Options
None
Anchor Clip U.S. Pat. 6418678 (other patents pending)
69
Butyl Tape
Sealant Tape
• Withstands extreme roof temperatures
• Superior low temperature compressibility
• Cold flow resistant
• Resistant to UV light
• Contains anti-oxidants, fungicides and anti-bacterial agents
• Seal not affected by normal movement of building
• Wide service temperature range
• Designed for side and end lap sealing of metal panels, roof
vents and pipe flashing
• Exceeds sealing requirements for AC, refrigeration and
windows
• Extruded on silicone coated paper for easy application
• Greater cohesive strength
• Superior adhesion
Tested Physical Properties
Test Method
Test
Typical Results
GSTM 10*
ASTM D-217-68
Color
Cone penetration @ 77°F/25°C,
105g/5sec. 1/10mm
Non-volatiles, % weight @ 212±
3°F/100±-2°C
Weight/gallon @ 77°F
Weight/liter @ 25°C
Specific gravity @ 77°F/25°C
Service temperature - range
Light Grey
55
ASTM C-771-74
ASTM D 792-66
ASTM D 792-66
GSTM 11*
Meets or exceeds all requirements of:
• Military Spec MIL-C 18969B Type II
Class B
• Federal Spec TT-C 1796A Type II
Class B
• N.A.A.M.M. SS-1C-68
• A.A.M.A. 804.1 AND 807.1
• M.B.M.A. Ice Damming - Five-Inch
static water head test
• F.D.A. Regulations (#175.125)
GSTM 16*
ASTM C-765-73
GSTM 9*
GSTM 1*
ASTM D-897-72
ASTM D-750-68
Sag (3 weeks @ 160°F/71°C)
Cold temperature flexibility 1/2" (12.7 mm)
Mandel Bend @ -60°F/-51°C
Webbing and elongation:
@ 77°F/25°C
@ 32°F/0°C
Adhesive/cohesive failure mode @
77°F/25°C
Tensile strength, p.s.i. @ 77°F/25°C
Weatherability - 1,000 hours in Q.U.V.
weatherometer (Cycle of 8 hours
U.V. @ 150°F/65°C; then 4 hours of
condensation @ 104°F/40°C)
99+
12.9 lbs
1.50 kg
1.55
-60° to +275°F
-51° to +135°C
None
No cracking or
loss of adhesion
1,050%+
3,050%+
3%/97%
25
No discoloration
cracking, crazing, or
loss of adhesion
* GSTM test methods available upon request.
Application Recommendation
Surfaces: All surfaces to be sealed should be free of dust, dirt, oil and moisture before applying sealant.
Temperature: Apply in dry conditions above 40°F (4°C); At temperatures below 40°F (4°C) atmospheric condensation surfaces inhibit
adhesion and should be avoided.
Application: Apply MB-10A tape to surface directly from roll. Press sealant through the silicone release paper with a smooth, even hand motion.
Note: for metal roofing and siding applications, place sealant under the fastener to prevent wind blown rain from leaking through the fastener holes.
Selection
SFS Part #
V8000
V8020
V8040
V8080
Size
3/16" Bead Butyl Sealant
3/8" x 3/32" Butyl Sealant
Feet Per Roll
25' Roll
45' Roll
50' Roll
50' Roll
Rolls/Carton
48
48
20
14
Rolls are packed in water-resistant cartons.
70
Hannoband® BG1
Joint Sealant Tape
• Hannoband® BG1 is a pre-compressed, self-expanding polyurethane
foam with acrylate dispersion impregnation
• Provides resistance to rain, wind, sound, draft and dust
• Use for sealing joints and seams in metal panels, gaps around door and
window frames, and expansion joints in buildings
• Pressure sensitive adhesive for fast and easy installation
• Flame retardant
BG1 provides maximum environment protection by:
• Greatly reducing air infiltration
• Highest levels of resistance to wind driven rain
• Superior sound proofing
• Extended functional life
• Highest fire rating
• Smallest thermal change (temperature gradient) inside and outside of
sealed joint
Technical Data
Property
BG1
Color
Air Tightness
ASTM E 283
Resistance to water penetration
Heat resistance
ASTM E 331/E 547
Tensile strength
Elongation
Compression force
Density
Thermal Conductance
Shelf Life
ASTM D3574/ISO 1798
ASTM D3574/ISO 1798
ASTM D3574/ISO 3386
ISO 845
DIN EN 12667
black
2,4 l/sm (360 Pa) (1,59 cfm/ft (7,5 psf))
0,55 l/sm (75 Pa) (0,3 cfm/ft (1,57 psf))
≥ 600 Pa (≥ 12,5 psf)
-30°C - 90°C (-40°F - 194°F)
Short Term: -40°C - 120°C (-40°F - 248°F)
> 100 kPa / > 14 psi
> 200%
3,4 kPa / 0,49 psi, 40% compression
65 kg/m³ ± 10% (4 lb/ft³)
λ = 0,0429 W/mk
18 months from date of production
Selection
Part #
1305091
1305092
Compressed
Dimension
1/4" x 1"
3/8" x 1"
Expanded
Dimension
1" x 1"
1-1/2" x 1"
Joint
Depth
1"
1"
Joint Width
Max. Min.
1/8" 1/4"
1/4" 3/8"
Roll
Length
26.2 ft.
18.4 ft.
Packaging
12 rolls/ctn
12 rolls/ctn
Disposal
Residue tape can be disposed of in the household waste. The local regulations are to be adhered to.
Safety
On the basis of existing data and experience, the product is not hazardous in the meaning of the Hazardous
Material Regulations. We recommend however that you take the same care and use the same hygiene as
with chemical materials.
Cleaning
Skin cleansing with soap and water. The impregnate and/or adhesive residues is possible with a
petroleum-based cleaning agent. Please observe the safety regulations.
71
Novaflex®
Metal Roof Sealant
Novaflex® metal roof sealant provides unbeatable adhesion to most
common construction materials, including Kynar®
• Non-corrosive, single component, oxime cured silicone sealant
and/or adhesive
• Applications include metal roofs and siding, wood, galvanized steel,
flashing, aluminum, PVC, windows and masonry
• Tack free in 10 minutes; completely cured in 2 days
• Permanently flexible; will not shrink, crack, sag or slump
• Provides a waterproof, weather tight seal
• Extrudes down to 0°F
• Will not freeze
Product Specifications
Physical Property
Test Method
Performance Range
Appearance
Extrusion Rate
Skin Over Time
Through Cure
1/8" Orifice @ 50 psi
3/8" @ 50%RH & 77° F
3/8" @ 50%RH & 77° F
Colored paste
30 - 80 grams
5 - 10 minutes
24 hours
Technical Properties*
Physical Property
Test Method
Specific Gravity
Tensile Strength
Elongation
Tear Resistance
Shore Hardness
Service Temperature
ASTM D412
ASTM D412
ASTM D 624
ASTM D 2240
Join Sealant Designation
ASTM C920
Adhesion
Glass
Aluminum
Vinyl
*
ASTM D 903
Typical Value
1.00 - 1.25
140 - 200 psi
500 - 650%
30 - 35 pli
22 ± 8
-40° C - 205° C (-40°F - 400° F)
Type S
Grade NS
Class 25
Use NT, M, G, A, O
12 - 15 pli
10 - 14 pli
12 - 15 pli
The values outlined reflect testing that was conducted on laboratory prepared specimens, actual results may vary.
The information provided in the above table is not intended for use in preparing specifications. Please consult
manufacturer for additional information.
72
Novaflex®
Metal Roof Sealant
Selection
Part #
1305155
Novaflex
Sealant Color
White
Part #
1305164
Novaflex
Sealant Color
Sandstone
1305156
Almond
1305165
Red
1305157
Dark Bronze
1305166
Brown
1305158
Black
1305167
Green
1305159
Sierra Tan
1305168
Antique White
1305161
Medium Bronze
1305169
Translucent
1305162
Light Gray
1305170
Charcoal Gray
1305163
Hemlock Green
1305171
Gutter Gray
Packaging
• Tube size and dimension: 10.3 fl. oz. (304 ml); 9" x 2" x 2"
• Case size: 12 tubes per case; weight - 20 lbs.
• Sold in case quantity only
Installation
• Cures times of materials listed on this sheet are dependent upon environmental conditions
such as temperature, humidity and application thickness
• Adhesion should be checked on small samples prior to full-scale application
• Can be used on interior and exterior
• Removable tips - no wasted sealant left in fixed tips
• No waste; ability to use entire tube, or can save with end cap
• Not paintable
Safety Advantages and Precautions
•
•
•
•
•
•
•
Low odor
Solvent free
VOC Compliant in all 50 states
Not recommended for surfaces that are to be painted
Not recommended for joints submerged under water
Do not install if surface temperature is below 0° F or exceeds 120° F
Obey all local, state and federal regulations for proper disposal of solvent and silicone waste
Storage
Shelf life of 18 months from date of manufacture when stored in the original, unopened container
at 75° F or less
73
Tools and Accessories
Installation
(RH3)screw
Description:
guns and
#3 drive
Phillips
sockets
Drive
(RH2)
Installation
ProductScrew
Name:
Guns
#14
• Screw guns and noise pieces are matched for individual products
to insure consistent installation performance.
Application
(RH4) Application: Insulation board
Installation
to roof cover.
tools
• Screw gun manufactures and individual tools are tested and
pre-qualified for reliable field performance before
recommendation.
DI 600 Power Screwdriver
Volts: 110
Amps: 6.5
Speed: 0 – 2000 rpm variable speed
For installing
self-drilling fasteners
Feature: Versa clutch system
CF 50 Setting Nose Piece
Installation tool with depth
locator for long SX composite
panel fasteners
Features:
ZA 1/4"/80 drive shaft
E 380 drive socket
irius® Drive Socket
Socket E-420
E-420 parts kit
Spare jaws
The E-420 setting tool is required
for installing the irius drive system
The fasteners are clamped firmly
via the teeth under the fastener head
Hex and Torx® Drive Bits
0973316
J0865
J0984
J0875
J0925
J0945
J0955
J6900
0895280
J6800
J2020
0514261
0761878
irius Drive Bit (E420)
1/4" x 2-9/16" x 1/4"
Lobular Hex Drive Mag Socket
1/4" x 1" x 1/4"
5/16" x 2-9/16" x 1/4"
3/8" x 2-9/16" x 1/4"
No. 3 Sq. Recess Drive Bit
2/2 Quadrex x 3" x 1/4" Hex Drive
1/4 Hex Magnetic Bit Holder
T20W TORX Drive Bit
T25 TORX Drive Bit 1"
T25 TORX Drive Bit 1-5/16"
SFS T-25 TORX Special For Evergrip
T30 TORX Drive Bit
74

Application - iMetal.net

Transcription

Similar documents

Aerospace Quality Fasteners and Hardware

classic service van for ford transit

GRUE TOUT-TERRAIN DE 1500 TONNES PRÈS DE LA CHUTE

Compact Track Loader

Compact Track Loader

- Gryfair.cz

PadPak Jr.

19 FT Center Console Boat Comparison | Yamaha Boats

PadPak AutoPad Senior

the token hunter - National Utah Token Society