2016 Tri5 Catalog - Classic Industries

Transcription

Radiators
1955-57 Extreme Series Cooling Systems
These Be Cool Extreme series cooling system modules offer the ultimate in fit, finish,
and performance. At the heart of every module is a direct-fit, dual core, crossflow
radiator sealed with a machined cap and mounted in an exclusive aluminum core
support. A hand-fabricated aluminum overflow tank and matching windshield washer
fluid reservoir are mounted on either side. Air is pulled through the radiator by two
high-torque electric fans with machined motor covers and mounting brackets. These
modules come pre-assembled with stainless steel hardware and includes a fan wiring
harness with temperature sender and waterproof 40 amp relays. Designed to cool
engines producing up to 700 horsepower and comes fully polished. Made in the USA.
Note: Modification to upper and lower hoses and transmission lines required for crossflow
upgrade. Short water pump required. Shipped truck freight. No further discounts apply.
Designed For Up To 700 Horsepower! Made in the USA!
TF600114
1955-57 Reproduction Radiators
These reproduction radiators install on the grill side of the core support on your
1955-57 Chevrolet model with OEM precision, mounting correctly with original
style brackets. Each radiator is equipped with a new... not rebuilt, tank and core.
Comes with original style mounting brackets attached and installs as original to
the radiator support. These high efficiency radiators feature a copper core with 1/2"
tubes on 3/8" centers 3 row core for the 6 cylinder models and a 4 row core for the
V8 models which gives you increased cooling without modifications to your car.
Fan shrouds, radiator petcock and radiator cap are not included and sold separately.
Note: Shipped oversize.
OS1
TF600128
Radiators For Six Cylinder
Grill Side Mounting
TF500219 1955-56
TF600240 1957
J
AC, Heater & Cooling System
16-5/8 x 23 x 2" .............................................. 359.99
16-5/8 x 23 x 2" .............................................. 359.99
Radiators For Small Block
Engine Side Mounting
TF500218 1955-57 16-5/8 x 21-3/8 x 2-5/8" ................................. 389.99
Grill Side Mounting
TF600114 1955-56 16-5/8 x 21-3/8 x 2-5/8" ................................. 399.99
TF500217 1957
16-5/8 x 21-3/8 x 2-5/8" ................................. 399.99
Radiators For Big Block
Grill Side Mounting
TF500217 1957
16-5/8 x 21-3/8 x 2-5/8" ................................. 399.99
TF600114 1955-56 16-5/8 x 21-3/8 x 2-5/8" ................................. 399.99
Bolt-In Installation
60% Lighter Than Copper/Brass
Up To 75% More Cooling Capacity
Fully Welded Construction
ea
ea
ea
ea
ea
ea
ea
Heavy Duty, Die-Stamped Tanks
Extra Thick Hose Connections
Billet Filler Neck
7 Plate Alum. Transmission Cooler
CR5122
1955-57
258
Radiators
3859.99
3859.99
3859.99
3859.99
3859.99
3859.99
set
set
set
set
set
set
3859.99
3859.99
3859.99
3859.99
3859.99
3859.99
set
set
set
set
set
set
4499.99
4499.99
4499.99
4499.99
4499.99
4499.99
set
set
set
set
set
set
4499.99
4499.99
4499.99
4499.99
4499.99
4499.99
set
set
set
set
set
set
1955-57 Crossflow Aluminum Conversion Modules
Be Cool radiators are designed to provide the added cooling capacity required by
high horsepower engines. These are complete module cooling systems that include
the polished aluminum radiator with radiator cap, dual electric fans, vented coolant
recovery tank, aluminum fan mounting brackets, electric fan wiring harness and all
necessary installation hardware. These mount in front of the core support and must
use short water pumps. Can be used with any engine combination.
Note: Upper and lower hose, and transmission line modification necessary to use crossflow
upgrade. Shipped double oversize. No further discounts apply.
1955-57 Northern Aluminum Muscle Car Radiators
OS2
Upgrade your cooling system with a high performance bolt-in radiator from
Northern®! Manufactured with race-proven technology, these radiators feature a
two-row, 1" core tube design for maximum cooling efficiency. Northern® fan and
shroud assemblies are also available for a matched cooling system.
Important: Dimensions listed include the radiator, tanks and brackets.
Models without AC
Models with Manual Transmission
TF600118 1955
small block/big block .......................................
TF600119 1955
LS1 ...................................................................
TF600120 1956
TF600121 1956
LS1 ...................................................................
TF600122 1957
TF600123 1957
LS1 ...................................................................
Models with Automatic Transmission
TF600124 1955
TF600125 1955
LS1 ...................................................................
TF600126 1956
TF600127 1956
LS1 ...................................................................
TF600128 1957
TF600129 1957
LS1 ...................................................................
Models with AC
Models with Manual Transmission
TF600130 1955
TF600131 1955
LS1 ...................................................................
TF600132 1956
TF600133 1956
LS1 ...................................................................
TF600134 1957
TF600135 1957
LS1 ...................................................................
Models with Automatic Transmission
TF600136 1955
TF600137 1955
LS1 ...................................................................
TF600138 1956
TF600139 1956
LS1 ...................................................................
TF600140 1957
TF600141 1957
LS1 ...................................................................
OS1
V8, 22-7/8" x 20-3/8" x 3-1/8" ........................ 499.99 ea
TF600171
TF600172
1955-57
1955-57
TF600173
TF600174
1955-57
1955-57
Polished Aluminum
23"x 22" standard transmission .................... 1419.99
23"x 22" automatic transmission.................. 1529.99
Natural Aluminum
23"x 22" standard transmission .................... 1269.99
23"x 22" automatic transmission.................. 1419.99
ea
ea
ea
ea
Toll Free Order Line 800.854.1280
Radiators/Fan Shrouds
flange
B
A
flange
C
Z40024
flange
flange
Northern Radiator Fan Shroud Kits
TF600262
1955-57 Polished Aluminum Radiators
These polished high performance radiators are
manufactured from tig welded aircraft grade aluminum
with brazed aluminum cores and billet filler necks. Each
radiator offers high capacity cooling with louvered
fins and 3/8" spacing between core tubes. Designed
for direct fit installation. Radiator cap is included.
Important: All radiators have built in automatic
transmission coolers and can be used in both automatic
and manual transmission applications. Core size
dimensions listed below.
OS1
Two Row Core
1955-57 8 Cylinder Mounting Position
TF600261 17-1/4" x 21-1/2" x 1-3/4" .. 169.99 ea
Three Row Core
1955-56 6 Cylinder Mounting position
TF600262 17-1/4" x 21-1/2" x 2" ......... 219.99 ea
1955-57 8 Cylinder Mounting position
TF600263 17-1/4" x 21-1/2" x 2" ......... 219.99 ea
Northern do-it-yourself fan shroud kits are an excellent way to get a custom fitted fan shroud for your radiator
and engine driven fan! Designed to fit exactly on Northern radiators (where specified), as well as most stock or
aftermarket radiators. Manufactured from .063" lightweight aircraft aluminum. Made in USA.
Part#
A
B
C
Fits Radiators:
Price
Z40020
19-5/16"
16-3/4"
2-1/2"
............................................................................ 59.99 kit
Z40021
19-5/16"
20-1/2"
2-1/2"
............................................................................ 59.99 kit
Z40022
19-5/16"
22"
2-1/2"
............................................................................ 59.99 kit
Z40023
19-5/16"
25-3/4"
2-1/2"
............................................................................ 59.99 kit
Z40024
19-5/16"
18-7/8"
2-1/2"
............................................................................ 59.99 kit
Z40025
17-7/8"
15-1/8"
2-1/2"
............................................................................ 59.99 kit
Z40026
18-1/8"
28-1/8"
2-1/2"
............................................................................ 59.99 kit
Z40026
18-1/8"
28-1/8"
2-1/2"
............................................................................ 59.99 kit
Z40027
16"
22-1/4"
2-1/2"
............................................................................ 59.99 kit
Z40028
16"
26-1/4"
2-1/2"
............................................................................ 59.99 kit
Z40029
18-5/8"
15"
2-3/8"
............................................................................ 59.99 kit
Z40030
18-1/2"
21-1/2"
2-7/8"
............................................................................ 59.99 kit
Z40031
18-3/8"
22"
2-5/8"
............................................................................ 59.99 kit
Z40032
16"
21-1/8"
2-1/2"
............................................................................ 59.99 kit
Z40033
25-1/8"
15"
2-1/2"
............................................................................ 59.99 kit
Z40034
18"
20-1/2"
2-1/2"
............................................................................ 59.99 kit
Z40036
22-7/8"
16-1/4"
2-5/16" CR5122 ............................................................... 59.99 kit
T9451
Universal Fan Shrouds
TF600225
TF600227
Economy Replacement Aluminum Radiator
Don’t be fooled by the price of these radiators. These
quality lightweight aluminum radiators stand up
to the demands of everyday driving with excellent
cooling properties. These replacement radiators vary
in appearance from the originals, but fit in the factory
mounting locations on vehicles with an 8 cylinder core
support. Silla radiators also are designed to work with
original fan shrouds. Every radiator includes fittings
for an automatic transmission cooler.
Important: The core is slightly smaller that the original;
this will not lessen cooling capabilities. Measure your core.
Hose adaptors are included.
OS1
SR002801
1955-57
1 row core ........ 189.99 ea
www.classicindustries.com
1955-57 Reproduction Metal Fan Shrouds
Reproduction metal fan shroud for 1955-57 models.
These shrouds are powder coated black for a durable,
long-lasting finish. These shrouds fit well and are easy
to install. Includes installation hardware and detailed
instructions. Made in USA.
Important: *V8 Models with radiator mounted in 6
cylinder position on a 6-cylinder core support should use
item number TF600225. **Requires TF500214.
OS1
6 Cylinder Core Support
TF600225* 1955-57 6 or 8 cylinder. 109.99 ea
8 Cylinder Core Support
TF600226 1955-57 8 cylinder ........ 109.99 ea
8 Cylinder Core Support - 6 Cylinder Position
TF600227** 1955-57 8 cylinder ........ 126.99 ea
TF500214
1955-57 Radiator Conversion Bracket Set
These brackets let you keep your 6 cylinder radiator
support while adding a V8. These will put your radiator
in the V8 position behind the radiator support. They
can also be used on a V8 support to put a radiator in
the 6 cylinder position for added clearance in front
of the engine. Bracket sets are available in both steel
and stainless steel.
TF500214 1955-57 steel ..................... 39.99 set
TF600270 1955-57 stainless steel....... 49.99 set
Radiators/Fan Shrouds
259
AC, Heater & Cooling System J
Shrouds will fit all small block and big block radiators.
Mounting hardware is included for installation. Will
replace all plastic and OEM shrouds and are available
in both chrome or EDP black finishes.
3" Wide 20" Diameter Shrouds
T9453
chrome finish............................ 39.99 ea
T9451
EDP black finish....................... 39.99 ea
5-1/2" Wide 20" Diameter Shrouds
T9454
chrome finish............................ 39.99 ea
Radiator Components
TF600166
1955-57 Radiator Drain Petcock And Hose
Reproduction radiator drain petcock with hose for
1955-57 Chevrolet passenger models. This petcock
is available separately or with 6" of rubber drain hose
included. It is manufactured to install on original or
reproduction replacement radiators.
K0085
1955-57 petcock only .......... 4.99 ea
TF600166 1955-57 petcock & hose...... 6.99 ea
1955-57 RC-549 Radiator Cap
Reproduction AC Radiator Cap for 1955-57 Chevrolet
passenger models. Authentic reproduction cap that
features correct markings on the radiator cap and is
officially licensed by GM Restoration Parts.
TF600164 1955-57
RC549 ............... 34.99 ea
1955-57 AC Delco RC-1 Radiator Cap
Replacement AC-Delco RC-1 radiator cap for 195557 models. Rated at the factory 7 lb. pressure rating.
G3546
1955-57
RC-1 .................. 8.99 ea
TF600175
TF600176
TF600150
1955-57 Radiator And Heater Hose Clamp Set
Reproduction all wire style clamps used on engine
radiator and heater hoses for 1955-57 Chevrolet
passenger models.
TF600149 1955-56 ............................ 5.99 set
TF600150 1957
deluxe heater....... 5.99 set
TF600151 1957
standard heater .... 5.99 set
60761
Stainless Steel Radiator Overflow Tanks
These beautiful polished stainless steel radiator
overflow tanks will give your engine compartment a
clean, custom look. They are available in various sizes
and feature a twist-on cap and mounting hardware.
60721
2" x 13" .................................. 39.99 ea
60731
2" x 15" .................................. 44.99 ea
60741
2" x 17" .................................. 45.99 ea
60751
2" x 19" .................................. 47.99 ea
60761
3" x 10" .................................. 49.99 ea
60781
3" x 16" .................................. 54.99 ea
1955-57 Billet Aluminum Radiator Cap
Billet aluminum radiator cap for 1955-57 Chevrolet
passenger car models to provide a unique custom look.
Rated at a 16 lb. pressure rating.
T6017
1955-57 16 lb. rating ............. 24.99 ea
TF600180
BC71003
1955-57 Radiator Overflow Hose
Replacement hose for the radiator overflow. Produced
with OEM style thin walled hose. This often overlooked
hose is notorious for deterioration.
B0056
1955-57 ................................. 4.99 ea
J
BC72003
Be Cool Radiator Accessories
Choose the right radiator cap and recovery tank to
complement your cooling system. Billet radiator
caps, rated at 13 psi, are recommended for all Be Cool
radiators, along with a proper coolant recovery tank,
which is safer for the environment than overflow tanks.
Aluminum brackets are also available to install the
stock fan shroud and finish your Be Cool conversion.
Radiator Caps
Round Style with Be Cool Logo
TF600175 polished finish..................... 54.99 ea
TF600178 natural finish ....................... 49.99 ea
Octagon Style with Be Cool Logo
Sure Grip Style with Embossed Emblem
Recovery Tanks
7" x 3" with Inlet & Mount Bracket
BC71003
polished finish..................... 149.99 ea
BC70003
natural finish ....................... 119.99 ea
Fan Shroud Mounting Brackets
BC72003
natural finish - 4 req............ 12.99 ea
260
Radiator Components
back side view
MR2470R
MR2470B
MR2470S
Thermocap Radiator Cap
Thermocap combines a high quality pressurized
radiator cap with a thermometer element, allowing
you to know when it’s safe to open your radiator
without any guess work. Easy to read temperature
gauge in Celsius and Fahrenheit. Specify red, blue or
silver when ordering.
Note: Stock cooling systems are rated at 7 psi.
MR2470
MR2471
13 psi ..................................... 34.99 ea
16 psi ..................................... 34.99 ea
1955-57 Radiator Bug Screen
Radiator bug screen for 1955-57 models. Ties in
front of the radiator to prevent bugs from clogging
the radiator core, reducing the cooling capacity. Add
an authentic look to your restoration while protecting
your cooling system.
TF600215
1955-57 .............................. 24.99 ea
Radiator Components
TF600159
1955-57 Reproduction Radiator Hoses
Z71051
Reproduction radiator hoses for 1955-57 Chevrolet
passenger models. Feature correctly numbered hoses
with GM codes printed on each hose. Provides for
an original factory look in the engine compartment.
Upper Radiator Hoses
TF600158 1955-56 6 cylinder ............... 21.99 ea
TF600159 1955-57 8 cylinder ............... 19.99 ea
TF600160 1956-57 dual 4 bbl & F.I. ..... 44.99 ea
TF600161 1957
6 cylinder ............... 32.99 ea
TF600212 1957
V8 Ram Jet engine 24.99 set
Lower Radiator Hoses
TF600162 1955-57 6 cylinder ............... 29.99 ea
TF600163 1955-57 8 cylinder ............... 20.99 ea
S7311
Flexible Stainless Steel Hose Sets
This is an ideal replacement for your worn or rotted
hoses. Noncorrosive construction conforms to tight
bends and holds shape indefinitely. Rated for high
temperatures and high pressure Can be easily cut to
custom lengths. This high quality set will enhance any
engine compartment.
Note: 48"radiator hose set has double quantity of end caps,
sleeves, reducers, and clamps. Save money and make both
upper and lower radiator hoses with one 48" set.
Z71004
Z71000
TF600154
1955-57 Replacement Radiator Hoses
Z71029
Z71027
Silicone Engine Coolant Plumbing Set
Note: *These hoses are for radiators mounted in front of
the radiator core support.
Upper Radiator Hoses
TF600155 1955-56 6 cylinder .............. 11.99
TF600153 1955-57 8 cylinder .............. 12.99
Lower Radiator Hoses
TF600154 1955-57 8 cylinder .............. 13.99
Ribbed Flex Hoses
TF600156 1957
6 cylinder upper .... 16.99
TF600157 1957
6 cylinder lower .... 15.99
Molded Radiator Hoses for Big Blocks
TF600207* 1955-57 upper ..................... 29.99
TF600208* 1955-57 lower...................... 29.99
set
set
set
set
set
set
set
set
set
set
ea
ea
ea
ea
ea
ea
ea
TF600145
1955-57 Heater Hose Sets w/GM Markings
HF1318
Flexible Radiator Hoses
If you’re doing an engine swap in your Chevrolet,
these flexible radiator hoses may be just what you
need to complete the cooling system installation. A
variety of sizes are available. Hose features a unique
design that allows it to conform to a variety of bends
and curves without kinking or collapsing.
HF1107 1-1/4" x 7-3/8"........................... 5.99 ea
HF1111 1-1/4" x 11" ............................... 9.99 ea
HF1119 1-1/4" x 19-9/16" x 1-1/2" ........ 9.99 ea
HF1123 1-1/4" x 23" ............................... 13.99 ea
HF1208 1-1/2" x 7-9/16"......................... 5.99 ea
HF1211 1-1/2" x 10-11/16" ..................... 9.99 ea
HF1212 1-1/2" x 12-3/16"....................... 9.99 ea
HF1317 1-1/2" x 16-5/16" x 1-3/4" ........ 9.99 ea
HF1217 1-1/2" x 17-1/16"....................... 9.99 ea
HF1318 1-1/2" x 19-1/2" x 1-3/4" .......... 13.99 ea
HF1220 1-1/2" x 19-13/16"..................... 13.99 ea
HF12205 1-1/2" x 20-1/2"......................... 9.99 ea
HF1222 1-1/2" x 22" ............................... 14.99 ea
HF12228 1-1/2" x 22-7/8" 90º end............ 10.99 ea
HF1223 1-1/2" x 23" x 1-3/4" ................. 9.99 ea
HF1225 1-1/2" x 25" ............................... 13.99 ea
HF1214 1-1/2" x 30" ............................... 9.99 ea
HF1316 1-3/4" x 16-5/16"....................... 12.99 ea
HF1319 1-3/4" x 18-13/16"..................... 13.99 ea
HF1323 1-3/4" x 23-1/2"......................... 9.99 ea
Reproduction of correct grooved hose with GM
markings for 1955-57 models. Each set includes the
correct clamps for each application.
TF600144 1955-56 6 cyl ......................... 34.99 set
TF600145 1955-56 8 cyl. ........................ 34.99 set
TF600146 1957
6 cyl ......................... 34.99 set
TF600147 1957
8 cyl w/std, dlx heater 34.99 set
TF600148 1957
8 cyl w/AC .............. 34.99 set
YE5215
Replacement Heater Hose
Replacement heater hoses are available in both
required diameters. These hoses are in 5 foot lengths
for a cut-to-fit use.
YE5210 5/8" 5 feet .............................. 5.99 ea
YE5215 3/4" 5 feet .............................. 4.99 ea
Radiator Components
261
Get the durability of silicone coolant hoses for your
custom engine install with these basic universal sets.
Each set contains a 90°, a 45° angled, and a straight
1-1/2" reinforced black silicone hose along with a
1-1/2" 45° mandrel bent and one straight aluminized
steel tube each featuring beaded ends for a positive seal.
Individual components also available for building your
own system or adding onto the radiator hose set here.
Radiator Hose Set
Z71051 1-1/2" silicone hose set ............ 79.99 set
Individual Components
Aluminized Steel Coolant tubes
Z71000 1-1/4" x 4" x 6" 90° bend ..... 24.99 ea
Z71001 1-1/2" x 4" x 6" 90° bend ..... 24.99 ea
Z71002 1-3/4" x 4" x 6" 90° bend ..... 24.99 ea
Z71003 1-1/4" x 4" x 6" 75° bend ..... 24.99 ea
Z71004 1-1/2" x 4" x 6" 75° bend ..... 29.99 ea
Z71005 1-3/4" x 4" x 6" 75° bend ..... 29.99 ea
Z71006 1-1/4" x 4" x 6" 45° bend ..... 24.99 ea
Z71007 1-1/2" x 4" x 6" 45° bend ..... 24.99 ea
Z71008 1-3/4" x 4" x 6" 45° bend ..... 21.99 ea
Stainless Steel Coolant Tubes
Z71060 1-1/2" x 4" x 4" 90° bend ..... 34.99 ea
Z71061 1-3/4" x 4" x 4" 90° bend ..... 44.99 ea
Z71063 1-3/4" x 4" x 4" 75° bend ..... 44.99 ea
Z71064 1-1/2" x 4" x 4" 45° bend ..... 34.99 ea
Z71065 1-3/4" x 4" x 4" 45° bend ..... 44.99 ea
Z71066 1-1/2" x 3"
straight tube 24.99 ea
Z71067 1-3/4" x 3"
straight tube 29.99 ea
Reinforced Black Silicone Hoses
Z71031 1-1/4" x 5" x 5" 90° bend ..... 24.99 ea
Z71032 1-1/2" x 5" x 5" 90° bend ..... 24.99 ea
Z71033 1-3/4" x 5" x 5" 90° bend ..... 29.99 ea
Z71028 1-1/4" x 4" x 4" 45° bend ..... 24.99 ea
Z71029 1-1/2" x 4" x 4" 45° bend ..... 24.99 ea
Z71030 1-3/4" x 4" x 4" 45° bend ..... 24.99 ea
Z71025 1-1/4" x 6"
straight hose 19.99 ea
Z71026 1-1/2" x 6"
Z71027 1-3/4" x 6"
Step Up/Down Hose Connectors
Z71035 1-1/4" to 1-1/2" x 8" ................. 24.99 ea
Z71036 1-1/2" to 1-3/4" x 8" ................. 24.99 ea
Replacement radiator hoses for 1955-57 models.
Your choice of molded or ribbed flex hoses. Ribbed
flex hoses will bend to accommodate tight spaces or
unoriginal bends.
Heater Hose Sets
S7313
polished ends ............................ 73.99
S7314
chrome ends ............................. 77.99
Radiator Hose Sets Polished Ends
S7301
12" .......................................... 44.99
S7304
24" .......................................... 55.99
S7307
36" .......................................... 66.99
S7310
48" .......................................... 102.99
Radiator Hose Sets Chrome Ends
S7302
12" .......................................... 47.99
S7305
24" .......................................... 57.99
S7308
36" .......................................... 68.99
S7311
48" .......................................... 104.99
Radiator Components
K1231
Radiator Hose Reducer Bushings
These rubber hose reducers are designed for custom
applications to allow the use of a larger ID radiator
hose with smaller inlets and outlets on radiators, water
pumps and thermostat housings. Simply insert them
into the hose before installation.
K1231 2" ID to 1-3/4" ID .................... 8.99 ea
K1232 1-3/4" ID to 1-5/8" ID .............. 11.99 ea
K1233 1-3/4" ID to 1-1/2" ID .............. 8.99 ea
1955-56 Heater Valve Hose And Clamp Set
Reproduction heater valve hose for 1955-56 models.
Set includes reproduction hose with GM stamping
and 2 wire clamps.
TF600152 1955-56 ............................... 2.99 set
1955-57 Heater Hose Clip
This clip is for all 1955-57 models. The hose clip holds
two heater hoses. Bracket attaches under the battery
box and holds the heater hoses to the inner fender area.
3825416 1955-57 1 required .............. 6.99 ea
T9228
1955-57 Chrome Water Necks
Triple plated chrome. Distinctive custom design
replaces original equipment. Comes complete with
plated bolts and gasket. 1 year manufacturer’s warranty.
Early Style Water Necks
T9228
1955-57 O-ring type .............. 12.99 ea
T4788
1955-57 gasket style .............. 18.99 ea
Late Style Water Necks
T9468
1955-57 w/1⁄2" NPT port....... 10.99 ea
T9229
1955-57 O-ring type .............. 9.99 ea
T4789B 1955-57 gasket style .............. 14.99 ea
Replacement O-Ring
66610
O-ring ....................................... 1.99 ea
K0060
Big Block Water Pump Bypass Hose Set
Heater Hose Coupler Repair Set
J
Removes even the most corroded heater hose coupler
on vehicles. Contains a heater hose coupler remover
that can be driven into couplers and then turned out
with a 5/8"socket or wrench. When the coupler is
corroded the special tapered, reverse drill can be used
to remove the remaining connector. Then the tap can
be used to restore the original 1/2"-14 NPT threads.
Includes storage case with tray.
62450
................................................. 64.99 set
Universal Coolant Filter
Prevent dangerous clogs in your cooling system with
this in-line coolant filter. Featuring heavy duty solid
brass construction, this filter is installed in line with
the radiator hose ahead of the radiator to prevent dirt
and debris from entering and causing damage.
RF002 for heater hose .......................... 39.99 set
6015
PF1056
This complete set will replace your worn out, thinning
or deteriorating original hose with a correct replacement
hose. This set includes a pre-cut and pre-formed hose
and the two tower clamps.
0059
short water pump..................... 14.99 set
K0060
long water pump ..................... 9.99 set
PF1058
Swivel Water Necks
Swivel water necks rotate 360º and are great for
applications where the upper radiator hose is routed
different than stock applications. These water necks
are available in polished aluminum, chrome plated
aluminum or precision CNC machined stainless steel
and with necks at various angles. They will fit most
small block and big block engines.
Polished Aluminum
6015
15º ........................................... 14.99 ea
6003
45º ........................................... 14.99 ea
6009
90º ........................................... 15.99 ea
Chrome Plated Aluminum
6015C
15º ........................................... 19.99 ea
6003C
45º ........................................... 19.99 ea
6009C
90º ........................................... 22.99 ea
CNC Machined Stainless Steel
PF1058 0º ............................................. 139.99 ea
PF1054 15º ........................................... 181.99 ea
PF1056 45º ........................................... 181.99 ea
T9929P
T9928P
PF1007
PF1006
Stainless Steel Heater Hose Fittings
These stainless steel fittings thread into the water
pump and intake manifold to provide heater hose
attachments. Each set includes two fittings and are
available in four piece sets with two fittings and two
1/2" stainless steel pipe plugs.
For 5/8" ID Hose
PF1007 5/8" x 1-3/4" & 5/8" x 2-7/8"L. 29.99 pr
PF1006 5/8" x 1-3/4"L........................... 25.99 pr
For 5/8" ID Hose With 1/2" Pipe Plugs
PF1024 5/8" OD x 1-3/4"L.................... 39.99 set
PF1025 5/8" OD x 1-3/4" & 2-7/8"L..... 43.99 set
For 5/8" & 3/4" ID Hose
PF1008 5/8" x 1-3/4" & 3/4" x 1-3/4"L. 25.99 pr
PF1009 5/8" x 1-3/4" & 3/4" x 2-7/8"L. 29.99 pr
For 5/8" & 3/4" ID Hose With 1/2" Pipe Plugs
PF1026 5/8" & 3/4" OD x 1-3/4"L ........ 39.99 set
PF1027 5/8" x 1-3/4" & 3/4" x 2-7/8"L. 42.99 set
Individual Fittings
PF1001 5/8" OD x 1-3/4"L.................... 14.99 ea
PF1002 5/8" OD x 2-7/8"L.................... 17.99 ea
PF1003 3/4" OD x 1-3/4"L.................... 14.99 ea
PF1004 3/8" OD x 2-7/8"L.................... 17.99 ea
5355
Corbin Heater Hose Clamps
From the earliest days of production, Chevrolet used
a pinch type “Corbin” clamp to retain the heater
hoses on the heater core outlet tubes. These wire
type reproduction hose clamps are designed to retain
the heater hoses with no water or antifreeze leakage.
AU5354 9/16" o.d. hose ......................... 1.49 ea
5355
5/8" o.d. hose ........................... 1.49 ea
AU5356 11/16" o.d. hose ....................... 1.49 ea
AU5357 3/4" o.d. hose ........................... 1.99 ea
262
Radiator Components
T9930P
OEM Style Powder Coated Water Neck
These are “O” ring style water necks powder coated
in Chevy orange. Keep that original look and color
on your fresh engine with a new powder coated water
neck. Available for early, late or late with a hole
Chevy engines.
T9928P 1955-57 early Chevy ............. 39.99 ea
T9929P 1955-57 late Chevy................ 39.99 ea
T9930P 1955-57 late Chevy w/hole .... 45.99 ea
K0150
K0151
Water Pump Hose Outlet Fittings
Reproduction water pump hose outlet fittings for 195557 models. Each fitting screws into the water pump.
Hose Outlet Fitting
K0150
small block .............................. 19.99 pr
K0150
big block.................................. 19.99 pr
Bypass Hose Fitting
K0151
big block - slotted.................... 19.99 pr
Thermostat Housings
1513321
Water Outlet Restrictors
If coolant travels too fast, it doesn't absorb enough heat
inside the engine or properly cool down as it passes
through the radiator. That's why it is still important to
restrict coolant flow in applications where a thermostat
isn't desired. These restrictors come in a set of three
with a 5/8", 3/4", and 1" hole to allow adjustment for
optimum cooling. Each 2-1/8" plate is made from
anodized aluminum and fits under the water outlet in
place of the thermostat.
263440 restrictor plate set ..................... 7.99 ea
1956-57 Water Temperature Sending Unit
The 1956-57 Chevy models had electrical temperature
gauges while the 1955 had mechanical temperature
gauges. These sending units are of the original design
and fit to work with your original temperature gauges.
Screws into engine.
TU4
1956 ..................................... 14.99 ea
1513321 1957 .....................................
9.99 ea
43631
High Performance Thermostat
These high performance thermostats are designed
to resist variations in coolant pressure, opening and
closing only at the correct temperatures, regardless
of engine RPM. Thermostats are made from brass
and copper with a high grade steel frame for years of
worry free operation.
43631
160 degree thermostat .............. 16.99 ea
43641
180 degree thermostat .............. 16.99 ea
G7137
1955-90 Silicone Sealed Thermostat Gasket
This revolutionary gasket uses an aluminum gasket
body with a silicone bead around crucial areas to
seal irregularities between the intake manifold and
thermostat housing. Compatible with all manifold
materials on 1955-88 small block and 1965-90 big
block Chevy engines.
738
1955-90 .................................... 17.99 ea
Thermostat
Choose the thermostat that you need depending on your
particular climate or engine requirements.
G7137 160º .......................................... 7.99 ea
G7138 170º .......................................... 10.99 ea
G7139 180º .......................................... 7.99 ea
G7140 195º .......................................... 7.99 ea
VP2002
1947-90 Cool-View Glass Thermostat
16401
Water Neck Gasket
Correct thermostat gasket for all GM 6 and 8 cylinder
engines from 1955-57. Recommended when replacing
original thermostat.
G7141 gasket ....................................... 1.99 ea
The “Balanced Sleeve” design of these High Flow
Thermostats equals out the pressure exerted on it by a
high flow water pump allowing it to be solely regulated
by coolant temperature. With the addition of a high
performance water pump and high flow thermostat,
you can expect a temperature drop of up to 25°F on
drives around town.
16400
160° ......................................... 21.99 ea
16401
180° ......................................... 21.99 ea
Important: Index pointer and gradient scale are only
included in sets with thermostat.
Note: Bolts not included. No further
discounts apply.
VP2001 w/o thermostat ......................... 109.99 ea
VP2002 w/180 degree thermostat ......... 139.99 ea
VP2003 w/195 degree thermostat ......... 139.99 ea
AR43741
Thermostat Housing Bolt Sets
Nobody likes water leaks. These premium grade
bolts are engineered to properly engage the manifold
threads and resist loosening. They come in your choice
of black oxide finished chrome moly or rust-proof
stainless steel, with handy 12-point or standard hex
heads. Washers included. Each set includes 3 bolts:
two 1" bolts and one 2" bolt.
AR13741 black oxide 12-point ......... 6.99 set
AR13742 black oxide hex head ........ 6.99 set
AR43741 stainless
12-point ......... 6.99 set
AR43742 stainless
hex head ........ 7.99 set
JT10170
1981-02 JET Low Temp Thermostat
Reduced engine temperatures add life to your engine
and provide a denser air/fuel mixture which helps
produce more horsepower. With the JET 180 degree
thermostat you get consistent engine cooling and
a precise metering of water throughout the engine.
Constructed of stainless steel.
JT10170 1981-92 all V8 ....................... 14.99 ea
JT10174 1993-97 LT1 .......................... 14.99 ea
JT10175 1998-02 LS1 .......................... 49.99 ea
Temperature Sending Unit Wiring Set
Reproduction temperature sending unit wiring set
which extends from the front light harness to the
temperature sending unit. Includes correct 24" insulator
cover and 30" green wire with bullet, blade or button
type terminals included.
CA34620 1956-57 ................................. 11.99 set
Thermostat Housings
263
AR13741
High Flow Thermostat
This 2" thermostat assembly allows you to see when
and how far the thermostat opens on a unique gradient
scale without ever removing the radiator cap. Made
from billet aluminum and the same specialized heavy
borosilicate glass used in steam boiler systems. Fits all
small and big block Chevrolet engines that use a nonbypass type thermostat, 1955 and up. Also fits all 216292 straight 6 engines from 1947-90. Made in USA.
Cooling System
FL14544
1955-57 Fan Blade
Flex-A-Lite Fan Spacers
blue
red
Correct reproduction fan blade for all 1955-57 V8 and 6
cylinder engines. Measures 17.5" in diameter and is an
exact replacement of your missing or damaged original.
B1017
1955-57 all 6 cyl. & V8 ......... 39.99 ea
Flex-A-Lite Series 1300 Flex Fan
Stainless steel blades flex at higher RPM’s which
reduces drag, pumps extra horsepower, and
improves fuel economy. For high-performance
and heavy-duty applications. Flex-a-Lite fan spacers
are sold separately.
Universal replacement fan spacers for use on
various applications.
FL14544
1/2" silver ........................ 15.99 ea
FL14548
1"
silver ........................ 15.99 ea
FL14556
2"
silver ........................ 19.99 ea
Important: Not for use with fan clutch assembly.
FL1307
FL1308
FL1309
FL1317
FL1318
FL1319
17317
red
red
red
blue
blue
blue
17" diameter ...............
18-3/8" diameter ........
19-1/2" diameter ........
17" diameter ...............
18-3/8" diameter ........
19-1/2" diameter ........
59.99
64.99
64.99
54.99
54.99
59.99
ea
ea
ea
ea
ea
ea
A5600101
Derale high performance replacement fans feature
durable construction with excellent balance and are
rated for up to 8,000 RPM. Manufactured with a
universal heavy duty steel hub with a 5/8" pilot hole.
Available with riveted steel or aluminum blades.
Note: Not for use with a fan clutch.
17317
17318
17319
17320
A5600101
A5600102
A5600103
A5600104
A5600105
A5600106
A5600107
17"
18"
19"
20"
15"
17"
18"
17"
18"
19"
20"
steel blade
steel blade
steel blade
steel blade
alum blade
alum blade
alum blade
steel blade
steel blade
steel blade
steel blade
std rotation .
std rotation .
std rotation .
std rotation .
std rotation .
std rotation .
std rotation .
rev rotation
rev rotation
rev rotation
rev rotation
34.99
34.99
34.99
34.99
44.99
44.99
44.99
34.99
34.99
34.99
34.99
ea
ea
ea
ea
ea
ea
ea
ea
ea
ea
ea
Rubber Fan Spacers
Rubber spacers are used with Champion Series electric
fans for proper spacing from the radiator.
MF112
................................................. 4.99 set
Derale Rigid Race Fans
Cooling System Zinc Anode
Zinc anode is found in heavy duty and marine
applications to protect cooling systems from
corrosion due to electrolysis or coolant additive
failure/breakdown. This simple component allows the
electrolysis process to "eat" the zinc rather than the
aluminum parts of your cooling system. Designed to
replace the drain petcock in your radiator, or any 1/4"
NPT hole along the cooling system.
FL32060 ............................................... 19.99 ea
Billet Aluminum Fan Brackets
Use this premium billet aluminum bracket set to mount
your 14" or 16" Champion or Challenger Series fan.
The set features four adjustable side angle brackets
that attach to the side flange of the radiator. Mounting
hardware is included.
MF105 .................................................. 45.99 set
Temperature Sending Wire Cloth Insulator
This 3/16" ID, 5/16" OD replacement cloth insulator,
keeps your temperature sender harness well insulated
from engine heat. Sold per foot. 2-3 feet required
per vehicle.
K0163
................................................. 1.50 ft
chrome
red
blue
J
Derale Flex Fans
These aluminum and stainless fan blades are rated up to
7,000 rpm and have chrome plated hubs. They feature
a narrow blade design for good airflow in tight space
applications. Embossed center hubs and four rivet blade
attachment provide increased strength.
9217 17" chrome stainless blade ..... 49.99 ea
9417 17" red
aluminum blade .. 44.99 ea
9517 17" blue
9218 18" chrome stainless blade ..... 49.99 ea
9418 18" red
9518 18" blue
FL5717
FL5718
Flex-a-Lite OEM Style Fan Blades
Reproduction fan blades for most GM applications.
Manufactured by Flex-a-lite for performance and
reliability these OEM style fan blades are to be used
with a fan clutch.
FL5717
17" ........................................ 41.99 ea
FL5718
18" ........................................ 44.99 ea
264
Cooling System
Electric Fan Controller
Dakota
akota Dig
Digital
D
Digital
Dakota Digital electric fan
controller is designed for
the ultimate in flexibility,
and to be a simple add-on
in any application using
an electric fan. Works
with your existing water
temperature gauge,
operating from the
DD2700
temperature sending
unit already installed.
A dedicated sending unit can be installed for
applications without a water temperature gauge. It is
recommended that the compact box (3" x 2.75" x 1")
be mounted inside the cab of the vehicle or alternate
dry environment. Operation Range: 150o F-250o F.
• Includes 70 amp relay
• Fully programmable "fan-on/off" temperatures
• Timed fan operation after the engine has been shut down
• Full digital LED display
Important: Must use a second 70 amp relay for dual fan or
two speed fan operation (# DD2702).
DD2700 with 70 amp relay ................... 119.99 ea
Relay for Dual Fan Applications
DD2702 70 amp relay ........................... 29.99 ea
Dedicated Temperature Sensors
DD2703 1/8" NPT sensor ..................... 14.99 ea
DD2704 3/8" NPT sensor ..................... 14.99 ea
DD2705 1/2" NPT sensor ..................... 14.99 ea
Universal Fan Bracket Strip Set
This bracket set is used to mount your Champion or
Challenger Series fan. Install the fan’s 90° mounting
feet (included with fan) to these four 7.25" long strips
for solid support. Mounting hardware is included.
MF104 .................................................. 19.99 set
Adjustable Fan Temperature Sensor
Turn your electric fan on at whatever your desired
temperature is with this adjustable temperature sensor.
Sensor adjusts from 180º-240º and helps prevent
overheating in performance vehicles when driving at
low speeds or when idling for long periods.
346932 180º-240º .................................. 41.99 ea
Cooling System
Challenger Series
Performance Fans
Adjustable Fan Temperature Switch
The adjustable temperature switch allows a wide range
of temperature settings for the Champion or Challenger
Series electric fan.
MF110 .................................................. 21.99 set
1955-57 Fan to Fan Clutch Bolts
Bolts used to attach a fan to the fan clutch on 1955-57
6 and 8 cylinder models. These replicate original GM
bolts with the correct markings. Bolts are sold in sets
of four and include lock washers.
1256621 1955-57 .................................. 9.99 set
1955-57 Fan Clutch to Water Pump Studs
Studs used to attach a fan clutch to the water pump
on 1955-57 6 and 8 cylinder models. Each stud set
includes four 5/16" double thread pitched studs with
four lock washers and nuts.
1256622 1955-57 .................................... 12.99 set
Fan Clutches
Fan clutch replacements
manufactured by Flex-a-Lite for
performance and reliability.
A great value on a quality fan clutch.
FL5537
FL5537
FL5555
FL5555
small block
big block
small block
big block
short water pump .
short water pump .
long water pump ..
long water pump ..
FL5537
54.99
54.99
54.99
54.99
ea
ea
ea
ea
Champion Series Low Profile
Performance Fans
Flex-a-Lite S-Blade Electric Fans
Flex-a-Lite S-Blade
electric fans are
the most efficient
S-blade fans
on the market.
These quiet fans
mount to the
core and can be
used to push or
pull air through
the radiator.
The high torque
motor makes these
fans strong enough to
replace your belt driven
FL396
fan and fan clutch, freeing
up horsepower and torque. The sweep style blades
squeeze out the maximum air flow possible.
12-5/8" x 11-3/4" x 2-5/8" Mount
FL392 12" fan 7.7 amp, 925 CFM ..... 99.99 ea
14-1/2" x 13-7/8" x 3-3/4" Mount
FL394 14" fan 9.2 amp, 1530 CFM .... 104.99 ea
16-5/8" x 15-3/4" x 4"Mount
FL396 16" fan 13.5 amp, 1980 CFM .. 129.99 ea
Flex-a-Lite Black Magic S-Blade
Recover up
to 17 HP and
INCREASE
YOUR
MILEAGE by
replacing the
old belt-driven
fan! Computerengineered blades
run quietly &
efficiently. Ring
fan provides
better blade
support for
impact resistance.
The advantages
of installing this universal fan include: reduced drag
on engine, improving mileage. Frees up serious
horsepower. Consistent cooling, regardless of
engine rpm. Easy bolt-on installation. Moves 3,000
CFM. Fits vehicles with 16" & wider radiator cores.
Universal mounting brackets included. 16" fan 18" x
16" x 4-1/4" mount.
FL160
................................................ 304.99 ea
The amazing Flex-aLite Syclone electric
fan is the most
efficient S-Blade
fan blade on the
market! This quiet
fan mounts to the
core and can be
used to push or
pull air through
the radiator. The
higher torque (17
amp) motor produces
2,500 cfm of air flow, making these fans strong
enough to replace your belt driven fan and fan clutch
to gain more horsepower and torque. The sweep style
blades squeeze out the maximum air flow possible.
16" fan. 16-5/8" x 15-3/4" x 4" mount
FL398
................................................ 144.99 ea
15" Electric Fan With
Thermostat
Your stock
fan robs your
engine of up
to 15 or more
horsepower!
Replace it
with a rugged,
universal-fit fan
equipped with
an adjustable
180°-240°F.
thermostat. Bolts
to your radiator
supports using
sturdy brackets.
With a heavy-duty motor, highly angled blades, and
15" diameter, this unit pulls up to 2,800 cfm of air,
cooling vehicles with up to 250 + HP (without air)
and 220+ HP (with air). Overall 18" x 16-1/8" x 4"
Amp draw - 14 amps.
67017
................................................ 164.99 ea
High Performance
Electric Fans
These
reversible fans
help prevent
overheating
in stop-andgo traffic,
designed to
fit the most
popular cars
and trucks,
increases
gas mileage,
67010
improves engine
performance, frees
the water pump pulley for more RPM, installs in
minutes with simple hand tools, 10" 12" 14" and
16" fans are reversible (mounts in front or back of
radiator). Ultra thin design to fit cramped locations.
Reinforced glass filled polypropylene blade and
plastic housing for minimized weight. Nylon tie
mounting kit included. Nominal fan size is based
upon approximate overall assembly diameter.
Plain Shroud
67010
10" x 2.5"
1000 CFM........ 41.99 ea
67012
12" x 2.5"
1200 CFM........ 49.99 ea
67014
14" x 4"
1650 CFM........ 59.99 ea
67016
16" x 4"
2100 CFM........ 61.99 ea
Shroud w/ Red Bow Tie
D141641 10" x 2.5"
1000 CFM........ 54.99 ea
D141642 12" x 2.5"
1200 CFM........ 59.99 ea
D141644 14" x 4"
1650 CFM........ 74.99 ea
D141646 16" x 4"
2100 CFM........ 79.99 ea
Cooling System
265
These Champion
Series performance
fans are the
lowest profile
of medium
and high
performance
fans on the
market. Quiet,
reversible
S-blade design
gives you the
choice of using
MF163
it as a puller or a
pusher fan. Manufactured from glass-filled nylon.
Includes powerful sealed motor, (4) 90° mounting
feet, mating locking pigtail and rubber spacers.
Recommended wire harness, temperature switch, and
adjustable thermostat sold separately.
Medium Performance Fans
MF123 12" x 2.48" 1,155 CFM....... 114.99 ea
MF146 14" x 2.87" 1,555 CFM....... 119.99 ea
MF166 16" x 2.87" 1,810 CFM....... 144.99 ea
High Performance Fans
MF122 12" x 3.19" 1,565 CFM....... 134.99 ea
MF142 14" x 3.19" 2,135 CFM....... 139.99 ea
MF163 16" x 3.19" 2,170 CFM....... 149.99 ea
These Challenger
Series performance
fans are
economical,
yet versatile
enough for high
performance
or daily
drivers. Quiet,
reversible
S-blade design
will operate
MF107
as a puller or
a pusher fan.
Manufactured from glass filled nylon. Includes (4)
90° mounting feet, mating locking pigtail and rubber
spacers. Recommended wire harness, temperature
switch, and adjustable thermostat sold separately.
High Performance Fans
MF136 13" x 3.82" 1,560 CFM.......... 91.99 ea
MF107 16" x 3.87" 1,950 CFM.......... 95.99 ea
MF162 16" x 4.35" 2,200 CFM.......... 101.99 ea
Flex-a-Lite Syclone Electric Fan
Cooling System
MF102
Electric Fan Wire Harness
With Sending Unit And Relay Set
This set is designed to allow worry-free automatic
operation of Champion or Challenger Series electric
fans. Includes a heavy gauge wire harness, relay,
weatherproof fuse, electrical connectors and 185° or
195° temperature sending unit.
For Carbureted Vehicles
MF102 w/185° temperature sender....... 61.99 set
For Fuel Injected Vehicles
MF103 w/195° temperature sender....... 61.99 set
Replacement Sending Units
MF108 185° carbureted engines ........ 21.99 ea
MF109 195° fuel injected engines ..... 21.99 ea
30140
Cooling Fan Shutdown
Painless F5 Fan Controller
This cooling fan shutdown kit shuts down your electric
cooling fan above 50-60 MPH to improve engine
cooling by preventing the electric fan from fighting
airflow through the radiator at highway speeds. The
unit is adjustable and may be overridden by using
the supplied dash mounted toggle switch. This kit is
designed to be used with the supplied signal generator
which must be installed into the speedometer cable.
TF900627 ............................................ 189.99 ea
This state-of-the-art fan control system uses pulse width
modulation to control electric fan speed from 50% up
to 100%. A three position toggle switch lets you choose
between normal operation, 100% fan speed, or turn the
fan(s) off. An AC compressor override that runs the
fans at 100% duty cycle if air conditioning is kicked
on. Includes a solid state controller rated for engine bay
use, 3/8 NPT threaded temperature sensor, large gauge
fan wires and labeled vehicle integration wire harness,
mounting hardware, and 70 Amp fuse and connectors.
The F5 Dual Fan Controller is rated to control two 35
Amp cooling fans. The F5 Single Fan Controller is rated
to control one 70 Amp cooling fan.
Electric Fan Wire Harness
w/Adjustable Switch And Relay
Note: No further discounts apply.
This set is designed to
allow a wide range of
temperature adjustments
for Champion or Challenger
Series electric fans.
Includes a heavy gauge wire
harness, relay, weatherproof
fuse, electrical connectors and
adjustable temperature switch.
MF100
30140
30141
w/adj. temperature switch ........ 61.99 set
J
“Ice Box” Cooling Fan Control
Available as a single fan control
or dual fan/2-speed fan control
unit. The sensor is simply
tightened under an intake or
water pump bolt. It can then be
adjusted to your exact preference
for on and off temperature.
It is equipped with an AC
Request system to turn the
cooling fan on whenever the
AC Compressor engages (this
TF900634
feature does not have to be used).
The dual fan control can operate two fans at different
temperatures or a single two speed fan at different
temperatures. Features exclusive lug sensor that
mounts under almost any engine bolt. Each unit has a
fully adjustable operating range of 140-230 degrees.
Note: *With Walker 2-speed fans.
TF900633 single control...................... 124.99 ea
TF900634 dual control ........................ 139.99 ea
TF900635* dual control ........................ 139.99 ea
Delayed Cooling System Shutdown
Timed cooling system shutdown features adjustable
relays that keep power to the cooling fan and electric
water pump (if equipped) when the key is shut off.
This reduces the block temperature as much as possible
without the risk of draining the battery. This is a timed
circuit and does not use a thermostat or other fan
control to operate.
TF900632 ............................................ 149.99 ea
30102
FK1000
1983-95 JET Fan Switch
The JET Fan Switch turns on the vehicle’s cooling
fan at a lower temperature than stock for improved
performance and engine longevity. Cooler operating
temperatures increase horsepower by providing
a denser air/fuel mixture. Installation is simple
replacement of the stock sensor. The JET Fan Switch
turns on at 195 degrees and turns off at 185 degrees.
JT60600 1983-92 all V8 ....................... 41.99 set
FK1000 1993-95 350 LT1 ................... 64.99 set
266
Cooling System
30116
Dual Fan - Dual Activation Fan Relay Kit
The dual activation cooling fan relay kit by Painless
Performance is exactly what you need to run dual
fans off of a thermostatic switch and when your a/c
is on. Installation takes just a few minutes and your
cooling fan will come on when the engine reaches
the preset temperature of the thermostatic switch
or when the a/c is turned on. Kit includes three 40
Amp relays with mounting bases, one fuse holder
with 70 amp fuse, pre-terminated and printed wire
harness, and your choice of thermostatic switch on/off
temperatures. Sets include 1/2"NPT to 3/8"NPT
adapter, mounting hardware, insulated terminals and
detailed instructions.
Fan-Thom/Fan-Thom II Electric Fan Relay
An absolute necessity if adding an on/off switch to
your electric fan circuit. Choose from the standard
fan relay or the weatherproof relays which provide
complete protection from the elements and ensure
reliable and dependable performance utilizing
heavy duty waterproof relays, weatherproof circuit
breaker covers and extreme condition weatherproof
shrinkable crimp-on terminals.
JT60600
dual fan controller ................. 264.99 set
single fan controller .............. 264.99 set
Fan-Thom I
standard.......................................... 35.99 set
weatherproof .................................. 54.99 ea
weatherproof w/195º/185º switch . 99.99 ea
weatherproof w/185º/175º switch . 99.99 ea
Fan-Thom II
Don’t want to probe your radiator? The Fan-Thom II
comes with a threaded thermostat that screws into the
engine block or manifold for a professional installation.
Thermostat thread size: 3/8"-18NPTF fitting.
30102 195º on/185º off ............................ 75.99 set
30106 185º on/175º off ............................ 74.99 set
Replacement Thermostats
30110 195º on/185º off ............................ 42.99 ea
30111 185º on/175º off ............................ 39.99 ea
30101
30130
30128
30129
30116
30117
30118
On 200F, Off 185F ................. 119.99 set
On 185F, Off 175F ................. 134.99 set
On 205F, Off 190F ................. 129.99 set
Adjustable Electric Fan Thermostat Set
Designed to allow a wide
range of
temperature adjustments
for your electric fan to set
the precise temperature
desired for fan activation.
The mounting
bracket is made of
brushed stainless
30104
steel for good looks
and durability. The complete set includes the
thermostat with bracket, a 30 amp relay, a 30
amp circuit breaker for overall protection, wiring,
terminals and mounting hardware.
Specs on Adjustable Fan Thermostat:
Temp range: - 32º to 248º F
Accuracy: +/- 7.3º F
Differential: 7.3º +/- 3.6º F.
Note: Temperature refers to the temp of the capillary tube,
not the coolant temp. No further discounts apply.
30104
30112
.................................................. 101.99 set
without relay ............................. 74.99 set
Water Pump Components
Stewart Components Stage 1
Cast Iron High Flow Water Pumps
5511167
1955-57 Original Style Water Pumps
Remanufactured or brand new water pumps for 1955-57
models with 6 or 8 cylinder engines. Remanufactured
V8 water pumps feature correct casting numbers.
The remanufactured pumps are rebuilt to "better
than original" specifications using superior, internal
components. New pumps are brand new castings using
modern technology and materials. Each pump will
install, look and function just like new.
No exchange required
Remanufactured Water Pumps
6 Cylinder Water Pump
58684
4-1/8" hub height...................... 81.99 ea
58128
5-1/4" hub height...................... 41.99 ea
8 Cylinder Water Pump - 265, 283
58638
casting # 3736493 .................... 69.99 ea
58635
casting # 3782608 .................... 84.99 ea
New Water Pumps
5511132 5-1/4" hub height...................... 47.99 ea
5511167 1 outlet, 4-hole hub .................. 29.99 ea
WP1450
Replacement Chrome Water Pumps
Each water pump features a new casting with top quality
bearing and excellent sealing. Each unit features the
highest quality triple chrome plating of any pump on
the market. Add a dash of flash to your engine.
No exchange required
Small Block Water Pumps
WP1354
short..................................... 119.99 ea
WP1449
long ..................................... 129.99 ea
Big Block Water Pumps
WP1448
short..................................... 131.99 ea
WP1450
long ..................................... 139.99 ea
Stewart Components
Stage 1 pumps use
brand new, original
equipment iron
castings that are
precision machined
to be compatible
with stock lines
WP12203
and brackets, and
are internally engineered for performance and
reliability. Applications suitable for use on V-belt or
serpentine belt systems are available. These water
pumps feature a 3/4" heavy duty bearing.
Small Block, Clockwise Rotation
WP12103 short 5/8" shaft ................. 94.99
WP12203 short 3/4" shaft ................. 99.99
WP13113 long
5/8" shaft ................. 99.99
Big Block, Clockwise Rotation
WP11104 short 5/8" shaft ................. 109.99
WP11113 long
5/8" shaft ................. 99.99
Big Block, Counter Clockwise Rotation
WP11105 short 5/8" shaft ................. 99.99
ea
ea
ea
ea
ea
ea
Stewart Components Stage 2
Aluminum High Flow Water Pumps
Important: These small block water pumps require the use
of a high flow, modified thermostat due to the elimination
of the factory bypass holes in the Stage 2 pumps. See
listings below for available temperatures.
169.99 ea
169.99 ea
169.99 ea
black finish
194.99 ea
24.99 ea
24.99 ea
24.99 ea
endurashine finish
1955-57 Edelbrock Water Pumps
These “super cooling” pumps are computer-designed
to deliver more flow at a higher velocity. Precision cast
powdered metal impellers have extra large vanes for
the maximum flow rate possible, ensuring adequate
pressure and volume even at lower engine speeds.
They feature a 5/8" pilot shaft.
Small Block Short Water Pumps
E8810
1955-57 cast finish ...............
E8820
1955-57 polished finish .......
E88103 1955-57 black finish ............
E88104 1955-57 endurashine finish..
224.99
304.99
259.99
294.99
ea
ea
ea
ea
Note: *Includes RH stud for ground strap.
K0177* big block
short water pump..
K0178* small block short water pump..
K0179 big block
long water pump ..
K0185 small block long water pump ..
9.99
9.99
9.99
9.99
set
set
set
set
Water Pump Bolt Sets
ARP’s water pump bolts are available in both
polished stainless steel or black oxide
finish chrome moly. You also can
choose between standard hex
head bolts or compact 12-point
AR43321
fasteners. Made in USA.
AR13322 black oxide hex head ......... 14.99 set
AR13321 black oxide 12-point .......... 15.99 set
AR43322 stainless
hex head ......... 24.99 set
AR43321 stainless
12-point .......... 24.99 set
Replace your original bolts
with these chrome plated or
stainless steel bolts for your
small block or big block
engine. Sets include four bolts
and washers.
AK136A chrome short pump ...........
AK135A chrome long pump ............
AK136B stainless short pump ...........
AK135B stainless long pump ............
AK136A
12.99
12.99
19.99
19.99
set
set
set
set
1955-57 Water Pump Bolts
These water pump bolts are the
correct style for 1955-56 V8
models. They feature the correct
TR markings on their heads as
original. 1955-56 sets include
one 2-3/4" bolt, three 1-15/16"
TF600290
bolts and four lock washers. 1957
sets include one 2-3/4" bolt, two 1-15/16" bolts, one
1-15/16 studded bolt and four lock washers.
TF600290 1955-56 ................................. 9.99 set
TF600291 1957 ...................................... 14.99 set
Small Block Chevy
Water Pump Spacers
These handy spacers
adapt an earlier short
style water pump for
proper pulley alignment
in later long water pump
applications. These are
also great when using an
aftermarket racing timing
chain cover where water
pump clearance is an issue.
Made from satin finished aluminum.
Bolts and gaskets included.
H8207
1955-57 Water Pump Rebuild Set
All the necessary parts to rebuild your original water
pump. These components are required when rebuilding
an original water pump designed for 1955-57 models.
Using all the components in this rebuild set will insure
that your original water pump will work and operate
efficiently.
WPK001 1955-57 V8........................... 62.99 set
1955-90 water pump spacers .. 71.99 set
Water Pump To Block Gaskets
Replacement water pump to
block gaskets for early small
and b ig block engines. Sold
individually. 2 required per vehicle.
G8337 small block ................................
G8338 big block ....................................
Water Pumps/Components
G8337
.99 ea
.99 ea
267
194.99 ea
179.99 ea
E8820
cast finish
K0179
Water Pump Bolts
Stewart Components
Stage 2 pumps use
brand new, 356-T6
heat treated aluminum
casting that are
precision machined
to be compatible
WP23113
with stock lines and
brackets. These pumps
feature several significant performance upgrades
compared to their Stage 1 pumps for maximum
performance. Applications suitable for use on V-belt
or serpentine belt systems are available. These
water pumps feature a 3/4" heavy duty bearing.
Small Block, Clockwise Rotation
WP22103 short 5/8" shaft ...............
WP22203 short 3/4" shaft ...............
WP23113 long
5/8" shaft ...............
Big Block, Clockwise Rotation
WP21104 short 5/8" shaft ...............
WP21113 long
5/8" shaft ...............
Big Block, Counter Clockwise Rotation
WP21105 short 5/8" shaft ...............
High Flow Modified Thermostats
WP300
160° ...............................
WP301
180° ...............................
WP302
195° ...............................
K0177
Water Pump Mounting Set
Reproduction water pump mounting bolts.
Water Pump Components
G2132
14769
Original Style Water Pump Pulleys
Reproduction and original GM water pump pulleys for
6 cylinder, small block and big block engines. Available
in a variety of diameters and belt configurations.
Six Cylinder Engines
Single Groove Pulley
14769
short pump, 7-1/8" O.D. .......... 41.99 ea
Small Block Engines
14769
short pump, 7-1/8" O.D. .......... 41.99 ea
Double Groove Pulley
G8356 short pump, 6-1/4" O.D. .......... 78.99 ea
G2132 long pump, 6-1/4" O.D............ 109.99 ea
Big Block Engines
KW394 5-7/8" O.D. .............................. 49.99 ea
14543
6-1/4" O.D. .............................. 44.99 ea
GH1026 short pump, 7-1/4" O.D. .......... 139.99 ea
G2132 long pump, 6-1/4" O.D............ 109.99 ea
Chrome Water Pump Pulleys
J
Reproduction water pump pulleys in chrome finish
for various applications.
Small Block
T9600
short pump, 7.1" O.D. ............. 29.99 ea
T9604
long pump, 6.3" O.D. .............. 29.99 ea
T9601
short pump, 6.4" O.D. ............. 39.99 ea
T9605
long pump, 6.3" O.D. .............. 39.99 ea
Big Block
T9723
long pump, 6.3" O.D. .............. 49.99 ea
66225BK
Chevrolet Electric Water Pumps
MR4333
Eliminates unnecessary weight and impeller-drag
experienced at high RPM, pumps up to 35+ gallons
of water per minute, and delivers the cooling that can
make the difference between a win and second place!
Durable, but light-weight die-cast aluminum, epoxy
powder coated for corrosion resistance in the color of
your choice. Race or street. Draws 6 amps. Mounting
hardware and fitting for water pump is included.
Small Block Water Pumps
Without Red Bow Tie
66225B
blue ................................... 204.99 ea
66225BK
black ................................. 204.99 ea
66225CR
chrome .............................. 254.99 ea
66225P
polished ............................ 234.99 ea
66225R
red ..................................... 204.99 ea
With Red Bow Tie
D141653
blue ................................... 219.99 ea
D141651
black ................................. 229.99 ea
D141650
chrome .............................. 269.99 ea
D141654
polished ............................ 249.99 ea
D141652
red ..................................... 219.99 ea
Big Block Water Pumps
Without Red Bow Tie
68230B
blue .................................... 219.99 ea
68230BK black................................... 219.99 ea
68230C
chrome ............................... 269.99 ea
68230P
polished.............................. 249.99 ea
68230R
red ...................................... 219.99 ea
With Red Bow Tie
D141673
blue .................................... 234.99 ea
D141674
black................................... 234.99 ea
D141671
chrome ............................... 289.99 ea
D141670
polished.............................. 269.99 ea
D141672
red ...................................... 234.99 ea
MR4396
MR4398
Electric Water Pump Drive Set
The electric water pump drive set was designed to
alleviate the power drag produced by conventional
pulley drive units. A heavy-duty electric motor, turning
at approximately 1,500 rpm. This unit can be turned
on and off manually, during a run, or before and
afterwards, even with engine off. The set is complete
with motor mounting bracket, extra long bolts, spline
pulleys, drive belt, wiring and switch. You supply the
fan of your choice.
Note: *Features a larger motor pulley and longer belt to
drive pump approximately 40% faster.
Water Pump Drive Set
MR4333 Chevrolet V8, & 90º V6 ...... 114.99 set
MR4433* Chevrolet V8, & 90º V6 ...... 144.99 set
Service/Replacement Parts
MR4333/MR4433
MR4394 mounting plate ....................
MR4396 12 volt D.C. electric motor .
MR4399 large water pump pulley......
MR4333
MR4397 drive belt .............................
MR4398 small pulley, 10 spline.........
MR4433
MR4393 drive belt .............................
24.99 ea
74.99 ea
24.99 ea
29.99 ea
29.99 ea
24.99 ea
GH9001
1959-63 Water Pump Pulley For 348 & 409
Reproduction water pump pulley set for 1959-63 348
engine equipped with High Lift cam; also correct
for 409 engines. Manufactured exactly as original
including proper original GM numbers stamped in
the front pulley. Made in the USA.
GH1007 1959-63 rear pulley ................ 99.99 ea
GH1009 1959-63 front pulley (3724816) 89.99 ea
GH1011 1959-63 pulley reinforcement
4.99 ea
Buy The Set And Save
GH9001 3 piece set ............................... 192.99 kit
Warning: concerning water pump pulleys
Stock replacement, aftermarket stamped steel or cast iron pulleys
are not designed to exceed 400 horsepower or 6000 RPM. Using
reproduction pulleys on engines in excess of these limits may
result in catastrophic disintegration of the pulley causing severe
damage to the engine, cooling system and body parts. Classic
Industries® assumes no liability for damages caused by improper
usage of pulleys. Please be sure to install the pulley properly to
avoid damages that could occur from improper installation or
exceeding the recommended RPM limitations.
268
50106
30132
Electric Water Pump Relay
These relays provide maximum battery voltage to
maximize cooling efficiency and to protect the main
electrical system from damaging amperage overloads.
Choose from a standard water pump relay or a
weatherproof water pump relay which is perfect for
the harsh weather conditions, this relay set provides
complete protection from the elements and ensure
reliable and dependable performance. These sets utilize
heavy duty waterproof relays, weatherproof circuit
breaker covers and extreme condition weatherproof
shrinkable crimp-on terminals.
87101
1962-79 Gilmer Belt Drive Set
These Gilmer drive sets for small block street/strip
engines are machined from billet aluminum and prevent
slippage and belt throwing at high RPM. Designed to
work with factory alternator brackets. Set includes
crank pulley, water pump pulley, alternator pulley
and a 1-1/2" wide belt.
50106
30132
87101
87111
Water Pumps/Components
Note: Not for vehicles with power steering or AC.
standard .................................. 39.99 ea
weatherproof .......................... 71.99 ea
283-400 w/short water pump ... 183.99 set
283-400 w/long water pump.... 197.99 set
Air Conditioning
Keep Your Tri-Five
Sanden AC Compressors
With Air Conditioning Kits From Classic!
If you own a 1955-57 Chevy, you can install a complete behind-the-dash air
conditioning system, including a heater and defroster, while preserving an original
appearance. Feel the comfort of cool air without sacrificing the original look of your
dash! The all-new, Vintage Air Gen-IV, SureFit Tri-Five air conditioning, heating
and defrost systems are a giant leap forward in performance aftermarket climate
control systems. The Gen-IV systems feature all electronic controls requiring no
cables, capillary tube or vacuum connections. They are truly “fly-by-wire” systems
that use separate heating and cooling coils for superior performance. The internal air
control doors are servo operated to provide infinite dash, floor and defrost blending.
When retrofitting a modern
AC system, Sanden SD508 and SD7H AC
compressors are the first choice. Not only
do they produce colder air than the original
compressors, they require less horsepower to
turn. Rated for continuous duty at 6,000 RPM.
Available in natural or polished finishes.
AP4510
SD508 AC Compressors R134A
AP4510
natural, 2-groove v-belt .................................................... 204.99
Z6161A
polished, 2 groove v-belt .................................................. 264.99
Z6162A
polished, serpentine belt ................................................... 264.99
SD508 AC Compressors R12
Z6161
polished, 2 groove v-belt .................................................. 258.99
Z6162
polished, serpentine belt ................................................... 289.99
SD7H AC Compressors R134A
AP7312
natural, 2 groove v-belt..................................................... 224.99
ea
ea
ea
ea
ea
ea
1955-57 Original Style AC Belts
Officially licensed by GM, they
feature indented imprinting of the
correct GM emblem, part numbers,
broadcast code (where applicable),
belt size (where applicable), manufacturer's
symbol and construction-codes. These authentic looking
reproductions are cloth wrapped. The finishing touch to any serious restoration
and a great way to gain points over your car show competitors. You don’t want
something as simple as a worn or incorrect belt to keep you from winning your
next trophy, and you certainly don’t want to be left stranded on the way to your
next show. Officially licensed by GM!
TF700157
1955................................................................................. 34.99 ea
TF700158
1956................................................................................. 34.99 ea
TF700159
1957................................................................................. 34.99 ea
961057
System Features:
Coolant System Protector
R-12 to R-134a Retro-Fit Set
This set provides the necessary
components (except receiver/drier)
to convert your R-12 AC system
to use R-134a refrigerant. Includes
an O-ring set, 12 oz. Ester oil,
service port adaptors, service warning
label. Receiver/drier must be ordered
separately.
AP7134A ........................ 26.99 set
1955-57 Gen IV Electronic Sure Fit System
Get cool air for your hot ride! This comprehensive set features fully electronic
fly-by-wire controls, high capacity plate and fin cooling coil, brass parallel-flow
heater coil, and an evaporator assembly that mounts completely behind the stock
dash. Comes complete with SuperFlow condenser, compressor, mounting brackets,
drier, safety switch, preformed aluminum lines, firewall cover plate and all mounting
hardware... Everything you need to give your classic a modern AC and heating
system. These Sure Fit sets are designed to install with minimal drilling and no
fabrication required. Available as a complete kit with center vent or a complete kit
with 4 vents (no molded center vent - allows use of 4 individual louver locations).
Note: Special order, must be prepaid. Shipped double oversize.
No further discounts apply.
96155PCU
961057
96156PCU
961058
Set With Center Vent
1955-56 .........................................................................
1957 ..............................................................................
Set With Four Vents
1955-56 .........................................................................
1957 ..............................................................................
OS2
1349.99 set
1346.99 set
1349.99 set
1346.99 set
Headers AC Relocation Bracket
This steel air conditioning bracket
relocates the air conditioning
compressor to the left of the engine.
Designed to allow clearance for headers
in specific pre-1979 small block Chevy
applications.
7608
1955-79 ........... 21.99 ea
Impurities in water can
cause rust and corrosion
inside the radiator, water
pump, and cylinder heads.
Over time, this can lead
to a loss of cooling
efficiency. Joe Gibbs
Driven Coolant
System Protector
stops the adverse
effect of hard water to
help prevent cooling
system damage.
JG1330 12 oz bottle ........ 9.99 ea
JG1331 case of 12........... 119.99 ea
Purple Ice Super Coolant
Purple Ice is a high
performance, synthetic,
radiator coolant additive. It
reduces engine heat, fosters
optimum coolant flow and
lubricates the water pump
seals. Purple Ice
should always be
used in conjunction
with antifreeze
in regions where
freezing temperatures
occur. Purple Ice is
recommended for any water/glycol
pressurized cooling system, including
those using the traditional green
silicate based glycols or the newer
OAT or HOAT based glycols.
RP01600 12 oz. bottle ...
9.99 ea
RP12600 case of 12 ....... 183.99 cs
AC Parts
269
• Fly-By-Wire Fully Electronic Servo Motor Controls No Cables
or Capillary Tube To Route
• Infinite “Just Right Temperature” Air Blending
• Infinite Blower Fan Speed Adjustment (3-Speed Fan For '57)
• High Volume Dehumidified Defrost Mode
• Separate High Capacity Aluminum Plate and Fin Cooling Coils
• Copper/Brass Cuprobreze™ Parallel Flow Heater Coil
• Mounts Behind The Dash
• AC Exits Through Center And Side Vents
• Uses Your Factory System Controls With Vintage Air’s
Exclusive Electronic Cable Converters
• Flat Steel Firewall Cover Panel (Stamped Oem Style On 57)
AC/Heater Parts
AC Hose
Bubble
Crimper
Evaporator Case Seals
When you need to
fabricate speciallysized hoses, this
easy-to-use bubble
crimping kit gets the
job done at home with
professional results.
Includes the crimper,
crimping dies for #6 (3/8"), #8 (1/2"), #10 (5/8") ,
#12 (3/4") fittings and an easy storage plastic
carrying case.
K2469
................................................. 269.99 set
Help avoid leaks with these evaporator case seals to
protect the investment you’ve made in your AC system.
AP0250 ...............................................
6.99 set
TF600167
13904
OE Style Cloth Defroster and Heater Hose
TF600168
1957 Air Duct Drain Tube
Reproduction inner fender drain tube for all 1957
models. This tube is bolted to the air duct and helps
drain moister that gets into the air duct system. Two
required per vehicle.
TF401114 1957 LH/RH ..................... 18.99 ea
1955-57 Reproduction Heater Cores
Reproduction heater cores for 1955-57 models. These
feature copper and brass construction for the ideal heat
dissipation to warm and defrost your classic. Mounting
plates available separately. Made in the USA.
Heater Cores
TF600167
1955-56 ............................ 153.99 ea
TF600168
1957 ................................. 183.99 ea
Mounting Plates
TF600169
1955-56 ............................ 13.99 ea
TF600170
1957 ................................. 14.99 ea
Reproduction defroster and heater hoses are the
original style, cloth-like cover over spiraled wire.
These will qualify for show as original. Offered in
various diameters to meet your under dash needs.
Sold in 3 foot lengths.
13901
1-1⁄2" diameter ........................ 21.99 ea
13902
1-3⁄4" diameter ........................ 21.99 ea
13903
2" diameter .............................. 24.99 ea
13904
2-1⁄2" diameter ........................ 24.99 ea
13905
3" diameter .............................. 27.99 ea
13906
3-1⁄4" diameter ........................ 27.99 ea
13907
3-1⁄2" diameter ........................ 27.99 ea
13908
3-3⁄4" diameter ........................ 27.99 ea
13909
4" diameter .............................. 32.99 ea
1957 Air Inlet Drain Tube Grommets
Without these grommets, the drain tube will become
loose and rattle and may be lost.
TF300261 1957....................................
2.99 pr
13914
Plastic Replacement Defroster Duct Hose
J
1957 Heater
Control Valve
Block Off Plate
This steel plate
mounts to the
firewall to block off the opening
for the heater control valve.
TF600275
Block off plate sets are painted
semi-gloss black and include a foam gasket with
mounting hardware.
TF600275 1957 block off plate set ..... 5.99 set
TF600276 1957 foam gasket only ...... 1.99 ea
This is a plastic replacement flexible hose under the
dash that is for the defroster, heater and fresh air
systems. These are for those who need the right hose
for the job and do not need an original style hose. Hose
is 72" in length, cut to desired length.
13916
1-1/2" ....................................... 28.99 ea
13910
2" .............................................. 24.99 ea
13911
2-1⁄4" ........................................ 24.99 ea
13912
2-1⁄2" ........................................ 26.99 ea
13913
2-3⁄4" ........................................ 34.99 ea
13914
3" .............................................. 28.99 ea
13917
3-1⁄4" ........................................ 42.99 ea
13915
3-1⁄2" ........................................ 42.99 ea
13918
4" .............................................. 36.99 ea
TF600231
TF600232
TF500220
1955-57 Heater Control Valves
Reproduction heater control valves for 1955-57
models. Heater valves are supplied without capillary
tubes, which can be re-used if necessary (1955
models only.)
TF500220 1955-56 .............................. 64.99 ea
TF600115 1957.................................... 59.99 ea
270
AC / Heater Parts
1955-57 Aluminum Heater Cores
Aluminum heater cores for 1955-57 models. These
all-new heater cores are exactly like originals except
they are manufactured in aluminum for lighter weight
and improved heat dissipation. 1957 heater cores
include mounting plate.
TF600231
1955-56 ............................ 109.99 ea
TF600232
1957 ................................. 129.99 ea
1957 Deluxe Heater Blower Motor Hose
Reproduction deluxe heater blower motor hose for
1957 models. This hose fits between the deluxe blower
motor and the inner fender duct. Reproduction hoses
are manufactured to original Chevrolet specifications
with quality vinyl plastic on a steel spring.
TF600106 1957 .................................... 16.99 ea
AC/Heater Parts
TF600104
1955-57 Standard & Deluxe Heater Seal Set
TF600206
Reproduction standard and deluxe heater seal sets for
1955-57 models. If your car is equipped with control
levers, you require a deluxe seal kit. If you have a fan
knob, you require a standard seal.
AP3155
Reproduction Heater Blower Motors
Note:* Includes defroster seal.
TF600211*
TF600103*
TF600104
TF600105
1955-56
1955-56
1957
1957
standard ................
deluxe ...................
standard ................
deluxe ...................
17.99
17.99
14.99
15.99
ea
ea
ea
ea
1955-57 EZ-Slider Heater Cable Sets
These heater cables with Polyethylene lining provide
reduced resistance, maximum flexibility and instant
response even during severe weather conditions.
The outer shell can be removed to create an original
appearance.
AP3155
1955
w/o AC .................... 29.99 set
AP3156
1956
w/o AC .................... 29.99 set
AP3157
1957
w/o AC .................... 43.99 set
New reproduction blower motors for 1955-57 models.
These motors are manufactured to meet or exceed
OEM specifications for magnetic properties, design
and performance, motor rpm and windings. Fans
sold separately.
With Air Conditioning
TF600205 1955-57 3 speed - 2 wire .. 44.99 ea
Without Air Conditioning
TF600206 1955-57 2 wire ................. 64.99 ea
1957 Heater Defroster Seal
This seal is located between the heater distributor
assembly and the dashboard vent assembly, dries out
and needs periodic replacement. The defrost function
will not operate without this seal.
TF600107 1957 ..................................... 8.99 ea
TF600117
Deluxe Heater Assembly Fastener Set
TF600108
Includes all of the clips, sheet metal screws and machine
screws to do the job right.
TF600116 1955-56 deluxe heater....... 4.99 set
TF600117 1957
deluxe heater....... 4.99 set
1957 Fresh Air Duct Seal Set
The connector between the front duct assembly and
the rear duct and valve assembly.
TF600101 1957 ..................................... 11.99 ea
TF600109
1957 Blower Motor Sleeve Seal
These seals are located between the heater blower
and transition assembly. This rubber sleeve fits on
the base of the shaft.
TF600102 1957 ..................................... 5.99 ea
These clips are used to correctly connect the cables to
your heater and vent assembly. Sets include screws.
Deluxe Heater Cable Retainer Clip Sets
TF600108 1955-56 5 piece ................... 24.99 set
TF600109 1957
6 piece ................... 29.99 set
Individual Heater Cable Retainer Clips
TF600110 1955-57 straight tab............. 6.99 ea
TF600111 1957
offset tab................ 6.99 ea
1955-56 Deluxe Heater Shaft and Spring Set
Reproduction deluxe heater shaft and spring set for
1955-56 Chevrolet passenger models. Includes: 1 pin,
1 spring, 1 retaining clip and 2 washers. These parts are
hard to find when you are restoring your heater controls.
TF600209 1955-56 deluxe heater ......... 5.99 set
TF500212
TF600113
1955-56 Heater Control Levers
Reproduction heater control levers for 1955-56 models.
TF600112 1955 ...................................... 20.99 pr
TF600113 1956 ...................................... 21.99 pr
1955-56 Vent & Defrost Control Cable Set
We know how hard it is to get old cables to function
properly. Fear no more, we have the solution. A great
looking and functional reproduction. Sold in pairs.
Choose from smooth or ribbed knobs. Controls defrost
& passenger side vents.
TF500212 1955
smooth knobs .......... 67.99 set
TF500213 1956
ribbed knobs ............ 67.99 set
AP0555
1955-57 Blower Switch
Maximize your system with this improved switch
featuring a rear harness set up that allows the resistor
to be attached in the rear of controls.
AP0555 1955-56 ................................... 36.99 ea
AP0523 1957......................................... 43.99 ea
AC / Heater Parts
271
1955-57 Heater Cable Retainer Clips

2016 Tri5 Catalog - Classic Industries

Transcription

Similar documents

MMFAN-MOUNT Installation Instructions

case study - Adknowledge

Booster Pump Filter Cleaner v1

Baptistry Heater - Piedmont Fiberglass, Inc.

AF8000E AF10000E manual

Autocirc® Instant Hot Water Pump

4 Coronation Street

SCP 5000 - Karcher Cleaning Equipment

Portable RV Waste Pump - Xylem Flow Control

Dettson_Feuillet HYDRA Compact_EN_5.indd