Caterpillar Performance Handbook, January 2014

Transcription

TRACK-TYPE
TRACTORS
Caterpillar
Performance
Handbook
®
Edition 44
800.437.4228
www.hawthornecat.com
© 2014 Caterpillar. All Rights Reserved. CAT, CATERPILLAR, BUILT FOR IT, their respective logos, “Caterpillar Yellow,” the “Power Edge” trade dress as well as
corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission.
TRACK-TYPE TRACTORS
Hydraulic Controls
Bulldozers
Rippers and Winches
19
CONTENTS
TRACK-TYPE TRACTORS
WINCHES
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19-1
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19-3
Power Shift Drawbar Pull
vs. Ground Speed Curves. . . . . . . . . . . . . . . . . .19-18
Power Shift Travel Speeds . . . . . . . . . . . . . . . . . . .19-24
Ground Pressures . . . . . . . . . . . . . . . . . . . . . . . . .19-26
Extreme Slope Operation . . . . . . . . . . . . . . . . . . .19-28
PACCAR
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19-84
Physical Specifications. . . . . . . . . . . . . . . . . . . .19-85
Operating Specifications . . . . . . . . . . . . . . . . . .19-95
HYDRAULIC CONTROLS
Allied
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19-99
Physical Specifications. . . . . . . . . . . . . . . . . . 19-100
Operating Specifications . . . . . . . . . . . . . . . . .19-107
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19-29
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19-30
BULLDOZERS
TRACK-TYPE TRACTORS
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19-33
Summary of Blade Options. . . . . . . . . . . . . . . . . .19-34
Blade Selection . . . . . . . . . . . . . . . . . . . . . . . . . . .19-36
General Dimensions (Tractor and Blade) . . . . . . .19-39
SAE Blade Capacity Definition . . . . . . . . . . . . . .19-39
Blade Specifications. . . . . . . . . . . . . . . . . . . . . . . .19-40
Estimating Production Off-the-Job. . . . . . . . . . . .19-50
Job Condition Correction Factors . . . . . . . . . . . .19-55
Measuring Production On-the-Job . . . . . . . . . . . .19-56
Work Tools. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19-56
Special Attachments . . . . . . . . . . . . . . . . . . . . . . .19-57
Features:
●
Cat® Diesel Engines provide the power, high torque
rise, reliability and performance you can depend on.
●
HEUI™ on D6R and D7R increases fuel efficiency,
reduces smoke, improves cold starting and enhances
diagnostic capabilities.
●
Mechanical Electronic Unit Injector (MEUI™) on D8T,
D9T, D10T2 and D11T excels in its ability to control
injection pressure over the entire engine operating
speed range. It combines the technical advancement
of an electronic control system with the simplicity of
direct mechanically controlled unit fuel injection. These
features allow the engine to have complete control
over injection timing, duration, and pressure.
●
Common Rail fuel injection system on D3K/D3K2,
D4K/D4K2, D5K/D5K2, D6K/D6K2, D6N, D6T
and D7E machines; optimizes performance and fuel
consumption, minimizes heat rejection, and lowers
emissions.
RIPPERS
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19-59
Ripper Specification Diagrams
Adjustable Parallelogram Ripper . . . . . . . . . . .19-60
Radial Ripper . . . . . . . . . . . . . . . . . . . . . . . . . .19-62
Fixed Parallelogram Ripper . . . . . . . . . . . . . . .19-62
Specifications
Track-Type Tractors . . . . . . . . . . . . . . . . . . . . .19-63
Tip Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19-73
Estimating Ripping Production . . . . . . . . . . . . . .19-73
Seismic Wave Velocity Charts . . . . . . . . . . . . . . . .19-76
Estimated Ripper Production Graphs . . . . . . . . .19-81
Edition 44
PHB-Sec19-Track-TypeTractors(pg01-28).indd 1
19-1
12/20/13 8:57 AM
Track-Type Tractors
Features
●
Oil cooled steering clutches and brakes standard on
D9R, D10T2 and D11T.
●
Finger Tip Controls (FTC) of transmission, steering
clutches and brakes on D10T2 and D11T.
●
Differential steering allows infinitely variable turning
radius. Standard on the D5R, D6N, D6T, D7R,
D7E, D8R, D8T and D9T, allows the tractor to make
a “power turn” keeping both tracks working for more
traction and higher performance.
●
Electronic Hydrostatic Power Train System on D3K
through D6K/D6K2 allows power turns, stepless speed
range, smooth modulation, dynamic hydrostatic braking,
superior maneuverability and excellent controllability.
●
Electric Drive Power Train System on D7E allows stepless speed range, smooth modulation, and excellent
efficiency. When coupled with differential steer it provides superior maneuverability with locked-track pivot
turn capability and excellent controllability.
●
SystemOne™ Undercarriage extends undercarriage
system life, improves reliability, and reduces owning
and operating costs. Optional on D6T (all sources),
D6K/D6K2 and D6N, optional on D8T and D8R
(all sources), D3K, D4K, D5K.
●
Elevated sprockets (not on D6K or D7E) eliminate
final drive stress induced by roller frame movement
and ground impact loads. Final drives pull chain only.
Seals moved up out of dirt, sand and water for longer
life. Blade visibility improved because operator sits
higher.
●
Resilient mounted bogie undercarriage on D8R, D8T,
D9T, D10T2 and D11T reduces shock transmitted
to tractor. Allows track to conform to rough ground
for better traction.
●
Solid mounted undercarriage standard on D3K2 through
D5K2 provides stable platform for low impact, and high
abrasion applications. Provides optimum finish grading performance.
●
Oscillating undercarriage on D6K/D6K2 through
D7E and optional on the D8R and D8T decreases
ground shock to the machine and provides a smoother,
more comfortable ride for the operator.
●
Combined hand lever steering located left of operator
provides easier operation on D9R.
●
Standard Tractors designed for heavy dozing and general grading.
●
XL Tractor D6T offers higher horsepower and longer
roller frames for increased finish grading capability,
flotation and productivity.
●
Accessible modular design on D6N XL and up greatly
reduces drive train removal and installation time resulting in reduced repair costs.
●
Extra Wide (XW) gauge on D6T length roller frame
provides wider shoes for greater flotation and stability for steep slope grading.
●
●
Sealed and Lubricated Track reduces pin and bushing wear for lower undercarriage repair costs. Sealed
and lubricated track is standard on the D3K, D4K,
and D5K while heavy duty track chain is available on
D5R, D6K/D6K2, D6N, D6T, and D7E improves
wear life and reduces pin/bore stretching and cracking.
Tag link on D7R, D8R/D8T and up; L-shaped push
arms on D6N, D6T and D7E. Both designs allow
closer mounting of dozer blades. This reduces total
tractor length, improves maneuverability, balance,
blade penetration and pryout.
●
Low ground pressure (LGP) tractors offer greater flotation in soft, swampy conditions. Available on D3K
through D8T.
19-2
Edition 44
12/20/13 8:57 AM
Specifications
Track-Type Tractors
19
MODEL
D3K XL (LRC)
D3K LGP (LRC)
D3K2 XL
D3K2 LGP
Flywheel Power
55.2 kW
74 hp
55.2 kW
74 hp
59.7 kW
80 hp
59.7 kW
80 hp
Operating Weight*
7795 kg
17,185 lb
8093 kg
17,842 lb
7958 kg
17,544 lb
8403 kg
18,525 lb
Engine Model
C4.4 ACERT™
C4.4 ACERT
C4.4 ACERT
C4.4 ACERT
1900
1900
2200
2200
4
4
4
Rated Engine RPM
No. of Cylinders
4
Bore
105 mm
4.13"
105 mm
4.13"
105 mm
4.13"
105 mm
Stroke
127 mm
5.0"
127 mm
5.0"
127 mm
5.0"
127 mm
5.0"
4.4 L
269 in3
4.4 L
269 in3
4.4 L
269 in3
4.4 L
269 in3
Displacement
Track Rollers (Each Side)
6
6
6
4.13"
6
Width of Standard Track Shoe
406 mm
16"
635 mm
25"
406 mm
16"
635 mm
25"
Length of Track on Ground
2095 mm
83"
2095 mm
83"
2248 mm
89"
2248 mm
89"
Ground Contact Area
(w/Std. Shoe)
17 011 cm2
2637 in2
26 607 cm2
4124 in2
18 254 cm2
2848 in2
28 550 cm2
4425 in2
Track Gauge
1495 mm
59"
1725 mm
68"
1495 mm
59"
1725 mm
68"
Height (To Top of ROPS)
2763 mm
108.8"
2763 mm
108.8"
2763 mm
108.8"
2763 mm
108.8"
Overall Length (with P blade)
4266 mm
168"
4255 mm
167.6"
4266 mm
168"
4266 mm
168"
3275 mm
128.9"
3275 mm
128.9"
3275 mm
128.9"
3275 mm
128.9"
Width (w/o Trunnion and Blade
— Std. Shoe)
1901 mm
74.8"
2360 mm
92.9"
1901 mm
74.8"
2360 mm
92.9"
Ground Clearance
332 mm
13"
332 mm
13"
332 mm
13"
332 mm
13"
VPAT, Straight
2646 mm
104.1"
3149 mm
124.0"
2646 mm
104.1"
3149 mm
124"
VPAT, Angled 25°
2417 mm
95.1"
2874 mm
113"
2417 mm
95.1"
2874 mm
113"
195 L
51.5
U.S. gal
195 L
51.5
U.S. gal
195 L
51.5
U.S. gal
195 L
51.5
U.S. gal
GENERAL DIMENSIONS:
(without Blade)
Blade Types and Widths:
Fuel Tank Refill Capacity
*Operating weight includes ROPS canopy, operator, lubricants, coolant, full fuel tank, hydraulic controls and fluids, back-up alarm, seat belts, lights, rigid
drawbar, front pull device and standard service crankcase guard.
Edition 44
19-3
12/20/13 8:57 AM
Track-Type Tractors
MODEL
Specifications
D4K XL (LRC)
D4K LGP (LRC)
D4K2 XL
D4K2 LGP
Flywheel Power
62.6 kW
84 hp
62.6 kW
84 hp
68.8 kW
92 hp
68.8 kW
92 hp
Operating Weight*
8147 kg
17,961 lb
8501 kg
18,742 lb
8201 kg
18,080 lb
8510 kg
18,761 lb
Engine Model
C4.4 ACERT
C4.4 ACERT
C4.4 ACERT
C4.4 ACERT
1900
1900
2200
2200
4
4
4
Rated Engine RPM
No. of Cylinders
4
Bore
105 mm
4.13"
105 mm
4.13"
105 mm
4.13"
105 mm
Stroke
127 mm
5.0"
127 mm
5.0"
127 mm
5.0"
127 mm
5.0"
4.4 L
269 in3
4.4 L
269 in3
4.4 L
269 in3
4.4 L
269 in3
Displacement
7
7
7
4.13"
7
460 mm
18"
635 mm
25"
460 mm
18"
635 mm
25"
2248 mm
89"
2248 mm
89"
2248 mm
89"
2248
89"
20 682 cm2
3206 in2
28 550 cm2
4425 in2
20 862 cm2
3206 in2
28 550 cm2
4425 in2
1550 mm
61"
1725 mm
68"
1550 mm
61"
1725 mm
68"
Height (To Top of ROPS)
2763 mm
108.8"
2763 mm
108.8"
2763 mm
108.8"
2763 mm
108.8"
Overall Length (with P blade)
4274 mm
168"
4266 mm
168"
4266 mm
168"
4266 mm
168"
3275 mm
128.9"
3275 mm
128.9"
3275 mm
128.9"
3275 mm
128.9"
— Std. Shoe)
2010 mm
79.1"
2360 mm
92.9"
2010 mm
79.1"
2360 mm
92.9"
Ground Clearance
332 mm
13"
332 mm
13"
332 mm
13"
332 mm
13"
Ground Contact Area
(w/Std. Shoe)
Track Gauge
GENERAL DIMENSIONS:
(without Blade)
VPAT, Straight
2782 mm
109.5"
3149 mm
124.0"
2782 mm
109.5"
3149 mm
124"
VPAT, Angled 25°
2542 mm
100.1"
2874 mm
113"
2542 mm
100.1"
2874 mm
113"
195 L
51.5
U.S. gal
195 L
51.5
U.S. gal
195 L
51.5
U.S. gal
195 L
51.5
U.S. gal
19-4
Edition 44
12/20/13 8:57 AM
Specifications
Track-Type Tractors
19
MODEL
D5K XL (LRC)
D5K LGP (LRC)
D5K2 XL
D5K2 LGP
Flywheel Power:
Hydrostatic
71.6 kW
96 hp
71.6 kW
96 hp
77.6 kW
104 hp
77.6 kW
104 hp
9408 kg
20,741 lb
9683 kg
21,347 lb
9314 kg
20,534 lb
9646 kg
21,266 lb
Operating Weight:*
Hydrostatic
Engine Model
C4.4 ACERT
C4.4 ACERT
C4.4 ACERT
C4.4 ACERT
1900
1900
2100
2100
4
4
4
Rated Engine RPM
No. of Cylinders
4
Bore
105 mm
4.13"
105 mm
4.13"
105 mm
4.13"
105 mm
Stroke
127 mm
5.0"
127 mm
5.0"
127 mm
5.0"
127 mm
5.0"
4.4 L
269 in3
4.4 L
269 in3
4.4 L
269 in3
4.4 L
269 in3
Displacement
7
7
7
4.13"
7
510 mm
20"
660 mm
26"
510 mm
20"
660 mm
26"
2310 mm
91"
2310 mm
91"
2310 mm
91"
2310 mm
91"
23 562 cm2
3652 in2
30 492 cm2
4726 in2
23 562 cm2
3652 in2
30 492 cm2
4726 in2
1600 mm
63"
1750 mm
69"
1600 mm
63"
1750 mm
69"
Ground Contact Area
(w/Std. Shoe)
Track Gauge
GENERAL DIMENSIONS:
Height (To Top of ROPS Canopy)
2769 mm
109.0"
2769 mm
109.0"
2769 mm
109.0"
2769 mm
109.0"
Height (To Top of ROPS Cab)
2769 mm
109.0"
2769 mm
109.0"
2769 mm
109.0"
2769 mm
109.0"
Overall Length (with P Blade)
4321 mm
170.1"
4294 mm
169.1"
4321 mm
170.1"
4321 mm
170.1"
3199 mm
125.9"
3265 mm
128.5"
3199 mm
125.9"
3265 mm
128.5"
— Std. Shoe)
2110 mm
83.1"
2410 mm
94.9"
2110 mm
83.1"
2410 mm
94.9"
Ground Clearance
332 mm
13"
332 mm
13"
332 mm
13"
332 mm
13"
(without Blade)
VPAT, Straight
2782 mm
109.5"
3220 mm
126.7"
2782 mm
109.5"
3220 mm
126.7"
VPAT, Angled 25°
2636 mm
103.8"
2940 mm
115.8"
2636 mm
103.8"
2940 mm
115.8"
195 L
51.5
U.S. gal
195 L
51.5
U.S. gal
195 L
51.5
U.S. gal
195 L
51.5
U.S. gal
Edition 44
19-5
12/20/13 8:57 AM
Track-Type Tractors
Specifications
MODEL
D5R XL
D5R LGP
D6K XL
D6K LGP
—
—
Tier 3/Stage IIIA
Tier 3/Stage IIIA
Engine Emissions Tier
Flywheel Power:
111.8 kW
Hydrostatic
150 hp
111.8 kW
—
150 hp
—
93.2 kW
125 hp
93.2 kW
28,409 lb
13 467 kg
125 hp
Operating Weight:
Hydrostatic
Power Shift Differential Steer
Engine Model
—
16 668 kg
—
36,747 lb
17 997 kg
12 886 kg
39,677 lb
29,690 lb
—
—
C6.6 ACERT
C6.6 ACERT
C6.6 ACERT
C6.6 ACERT
2200
2200
2200
2200
6
6
6
Rated Engine RPM
No. of Cylinders
6
Bore
105 mm
4.13"
105 mm
4.13"
105 mm
4.13"
105 mm
Stroke
127 mm
5.0"
127 mm
5.0"
127 mm
5.0"
127 mm
5.0"
6.6 L
403 in3
6.6 L
403 in3
6.6 L
403 in3
6.6 L
403 in3
Displacement
7
8
7
4.13"
7
600 mm
24"
840 mm
33.1"
560 mm
22"
760 mm
30"
2611 mm
103"
3113 mm
122.6"
2645 mm
104"
2645 mm
104"
3.18 m²
4929 in²
5.23 m²
8107 in²
3.0 m2
4650 in2
4.0 m2
6200 in2
1890 mm
74.4"
2160 mm
85"
1770 mm
70"
2000 mm
79"
Ground Contact Area
(w/Std. Shoe)
Track Gauge
GENERAL DIMENSIONS:
3040 mm
119.7"
3144 mm
123.8"
2958 mm
116.5"
2958 mm
116.5"
3095 mm
121.9"
3200 mm
126"
2958 mm
116.5"
2958 mm
116.5"
Overall Length
(with VPAT Blade)**
4903 mm
193"
5369 mm
211.4"
5020 mm
198"
5020 mm
198"
(without Blade)**
3740 mm
147.2"
4165 mm
164"
4552 mm
179"
4552 mm
(with SU Blade)
5157 mm
203"
—
—
—
(with A blade)
4930 mm
194"
—
—
—
179"
— Std. Shoe)*
2500 mm
98.4"
3000 mm
118"
2330 mm
91.7"
2760 mm
108.7"
Ground Clearance
394 mm
15.5"
507 mm
20"
360 mm
14.2"
360 mm
14.2"
160.6"
3077 mm
121.1"
3360 mm
Semi-U
3154 mm
124"
VPAT, straight
3272 mm
128.8"
A Blade
4165 mm
164"
300 L
79.3
U.S. gal
—
4080 mm
—
—
300 L
—
—
79.3
U.S. gal
295 L
132.3"
—
77.9
U.S. gal
295 L
77.9
U.S. gal
*Width (w/o Trunnion — Std. Shoe) is also w/o VPAT Blade.
**D6K XL and D6K LGP with drawbar.
19-6
Edition 44
12/20/13 8:57 AM
Specifications
Track-Type Tractors
19
MODEL
D6K2 XL
D6K2 LGP
D6K2 XL
D6K2 LGP
Tier 3/Stage IIIA
Tier 3/Stage IIIA
Tier 4 Interim/
Stage IIIB
Tier 4 Interim/
Stage IIIB
Flywheel Power:
Hydrostatic
97 kW
130 hp
97 kW
130 hp
97 kW
130 hp
97 kW
130 hp
13 311 kg
29,346 lb
13 948 kg
30,750 lb
13 311 kg
29,346 lb
13 948 kg
30,750 lb
Operating Weight:
Hydrostatic
Engine Model
C7.1 ACERT
C7.1 ACERT
C6.6 ACERT
C6.6 ACERT
2200
2200
2200
2200
6
6
6
Rated Engine RPM
No. of Cylinders
6
Bore
105 mm
4.13"
105 mm
4.13"
105 mm
4.13"
105 mm
Stroke
127 mm
5.0"
127 mm
5.0"
127 mm
5.0"
127 mm
5.0"
6.6 L
403 in3
6.6 L
403 in3
6.6 L
403 in3
6.6 L
403 in3
Displacement
7 or 8
7 or 8
8
4.13"
8
560 mm
22"
760 mm
30"
560 mm
22"
760 mm
30"
2645 mm
104"
2645 mm
104"
2645 mm
104"
2645 mm
104"
Ground Contact Area
(w/Std. Shoe)
3.0 m2
4650 in2
4.0 m2
6200 in2
3.0 m2
4650 in2
4.0 m2
6200 in2
1770 mm
70"
2000 mm
79"
1770 mm
70"
2000 mm
79"
2958 mm
116.5"
2958 mm
116.5"
2958 mm
116.5"
2958 mm
116.5"
Overall Length
(with VPAT Blade)**
5008 mm
197"
5008 mm
197"
5008 mm
197"
5008 mm
197"
without Blade**
4588 mm
181"
4588 mm
181"
4588 mm
181"
4588 mm
181"
Track Gauge
GENERAL DIMENSIONS:
— Std. Shoe)*
2330 mm
91.7"
2760 mm
108.7"
2330 mm
91.7"
2760 mm
108.7"
Ground Clearance
360 mm
14.2"
360 mm
14.2"
360 mm
14.2"
360 mm
14.2"
VPAT, straight
3196 mm
125.8"
3682 mm
145.0"
3196 mm
125.8"
3682 mm
145.0"
VPAT, angled
2896 mm
114.0"
3337 mm
131.4"
2896 mm
114.0"
3337 mm
131.4"
295 L
77.9
U.S. gal
295 L
77.9
U.S. gal
295 L
77.9
U.S. gal
295 L
77.9
U.S. gal
**With drawbar.
Edition 44
19-7
12/20/13 8:57 AM
Track-Type Tractors
Specifications
MODEL
D6N XL
D6N LGP
D6N XL
D6N LGP
—
—
Tier 4 Interim/
Stage IIIB
Tier 4 Interim/
Stage IIIB
Flywheel Power:
Hydrostatic
111.8 kW
Power Shift
150 hp
111.8 kW
—
150 hp
—
—
—
111.8 kW
150 hp
111.8 kW
150 hp
16 507 kg
36,392 lb
18 096 kg
39,895 lb
Operating Weight:
Engine Model
16 668 kg
36,747 lb
17 997 kg
39,712 lb
C6.6 ACERT
C6.6 ACERT
C6.6 ACERT
C6.6 ACERT
2200
2200
2200
2200
6
6
6
Rated Engine RPM
No. of Cylinders
6
Bore
105 mm
4.13"
105 mm
4.13"
105 mm
4.13"
105 mm
Stroke
127 mm
5.0"
127 mm
5.0"
127 mm
4.99"
127 mm
4.99"
6.6 L
403 in3
6.6 L
403 in3
6.6 L
402.75 in3
6.6 L
402.75 in3
Displacement
7
8
7
4.13"
8
610 mm
24"
840 mm
33"
610 mm
24"
840 mm
33"
2611 mm
103"
3113 mm
123"
2611 mm
103"
3113 mm
123"
3.18 m2
4929 in2
5.24 m2
8122 in2
3.18 m2
4929 in2
5.24 m2
8122 in2
1890 mm
74.4"
2160 mm
85"
1890 mm
74.4"
2160 mm
85"
Ground Contact Area
(w/Std. Shoe)
Track Gauge
GENERAL DIMENSIONS:
3040 mm
119.7"
3144 mm
123.8"
3095 mm
121.9"
3200 mm
126"
3088 mm
NA**
121.6"
3190 mm
NA**
125.6"
Overall Length
(with VPAT Blade)
4903 mm
193"
5369 mm
211.4"
5148 mm
202.6"
5851 mm
230.3"
without Blade
3740 mm
147.2"
4165 mm
164"
3740 mm
147.2"
4165 mm
with SU Blade
5157 mm
203"
—
5222 mm
205.6"
—
—
2630 mm
103.5"
—
164"
Width (over Trunnion)
2630 mm
103.5"
Width (w/o Trunnion
— Std. Shoe)*
2500 mm
98.4"
3000 mm
118"
2500 mm
98.4"
3000 mm
118"
Ground Clearance
394 mm
15.5"
507 mm
20.0"
394 mm
15.5"
507 mm
20"
Semi-U
3154 mm
124"
3154 mm
124.2"
VPAT
3272 mm
128.8"
4080 mm
160.6"
3272 mm
128.8"
4080 mm
160.6"
300 L
79.3
U.S. gal
300 L
79.3
U.S. gal
300 L
79.3
U.S. gal
300 L
79.3
U.S. gal
—
—
**Canopy not available.
19-8
Edition 44
12/20/13 8:57 AM
Specifications
Track-Type Tractors
19
MODEL
Flywheel Power
D6R
D6R XL
D6R LGP
130 kW
175 hp
145 kW
195 hp
145 kW
195 hp
18 325 kg
40,400 lb
20 080 kg
44,270 lb
21 716 kg
47,874 lb
Operating Weight:*
Power Shift
Engine Model
C9 ACERT
C9 ACERT
C9 ACERT
2000
2000
2000
6
6
Rated Engine RPM: Power Shift
No. of Cylinders
6
Bore
112 mm
4.4"
112 mm
4.4"
112 mm
4.4"
Stroke
149 mm
5.9"
149 mm
5.9"
149 mm
5.9"
8.8 L
537 in3
8.8 L
537 in3
8.8 L
537 in3
560 mm
22"
560 mm
22"
915 mm
36"
2.61 m
8'7"
2.81 m
9'3"
3.25 m
10'8"
Ground Contact Area (w/Std. Shoe)
2.92 m2
4531 in2
3.15 m2
4878 in2
5.94 m2
9204 in2
Track Gauge
1.88 m
74"
1.88 m
74"
2.29 m
90"
Displacement
6
7
8
GENERAL DIMENSIONS:
Height (Stripped Top)**
2.40 m
7'11"
2.40 m
7'11"
2.45 m
8'1"
3.20 m
10'6"
3.20 m
10'6"
3.25 m
10'8"
3.20 m
10'6"
3.20 m
10'6"
3.25 m
10'8"
Overall Length (without Blade)
3.85 m
12'7"
3.85 m
12'7"
4.27 m
13'11"
with S Blade
—
—
5.48 m
with SU Blade
5.08 m
16'8"
5.33 m
17'6"
18'0"
—
with Angle Blade
5.00 m
16'5"
5.21 m
17'1"
2.64 m
8'8"
2.64 m
8'8"
3.43 m
11'3"
Width (w/o Trunnion — Std. Track)
2.44 m
8'0"
2.44 m
8'0"
3.21 m
10'6"
384 mm
1'3"
384 mm
1'3"
434 mm
1'5"
Ground Clearance
—
Straight
3.36 m
11'0"
Angle Straight
4.16 m
13'8"
4.16 m
13'8"
Full 25° Angle
3.77 m
12'5"
3.77 m
12'5"
—
Semi-U
3.26 m
10'8"
3.26 m
10'8"
—
425 L
112 U.S. gal
425 L
112 U.S. gal
—
4.06 m
13'4"
—
425 L
112 U.S. gal
**Operating weight includes ROPS canopy, operator, lubricants, coolant, full fuel tank, hydraulic controls and fluid, SU blade, horn, back-up alarm, retrieval
hitch and front pull hook.
**Height (Stripped Top) — without ROPS canopy, exhaust, seat back or other easily removed encumbrances.
Edition 44
19-9
12/20/13 8:57 AM
Track-Type Tractors
Specifications
MODEL
Flywheel Power
Operating Weight:*
SU Blade
Engine Model
Rated Engine RPM: Power Shift
No. of Cylinders
Bore
Stroke
Displacement
Track Gauge
GENERAL DIMENSIONS:
Height** (Stripped Top)***
Height** (To Top of ROPS Canopy)
Height** (To Top of ROPS Cab)
with SU Blade
with Angle Blade
Ground Clearance**
Angle Straight
Full 25° Angle
Semi-U
D6T
149 kW
20 580 kg
D6T XL
200 hp
149 kW
45,370 lb
21 600 kg
C9 ACERT
1850
6
112 mm
149 mm
8.8 L
200 hp
47,620 lb
C9 ACERT
1850
6
4.4"
5.9"
537 in3
112 mm
149 mm
8.8 L
560 mm
2.61 m
2.92 m2
1.88 m
22"
8'7"
4531 in2
74"
560 mm
2.81 m
3.15 m2
1.88 m
22"
9'3"
4878 in2
74"
2.40 m
3.11 m
3.11 m
3.85 m
5.08 m
5.00 m
2.64 m
2.44 m
384 mm
7'11"
10'2"
10'2"
12'7"
16'8"
16'5"
8'8"
8'0"
1'3"
2.40 m
3.11 m
3.11 m
3.85 m
5.33 m
5.21 m
2.64 m
2.44 m
384 mm
7'11"
10'2"
10'2"
12'7"
17'6"
17'1"
8'8"
8'0"
1'3"
4.16 m
3.77 m
3.26 m
425 L
13'8"
12'5"
10'8"
112 U.S. gal
4.16 m
3.77 m
3.26 m
425 L
13'8"
12'5"
10'8"
112 U.S. gal
6
4.4"
5.9"
537 in3
7
***Operating weight includes cab, operator, lubricants, coolant, full fuel tank, standard track, hydraulic controls and fluid, SU blade, drawbar and counterweight.
***Dimensions measured from ground line. Add grouser height for total dimension on hard surfaces.
***Height (Stripped Top) — without ROPS canopy, exhaust, seat back or other easily removed encumbrances.
Track-Type Tractor Sustainability
Well matched engine and power train systems enhance productivity and fuel efficiency.
19-10
Edition 44
12/20/13 8:57 AM
Specifications
Track-Type Tractors
19
MODEL
Flywheel Power
Operating Weight:*
VPAT
Engine Model
Advertised Engine RPM
No. of Cylinders
Bore
Stroke
Displacement
VPAT
VPAT
VPAT
VPAT
Track Gauge
VPAT
GENERAL DIMENSIONS:
Height** (Stripped Top***)
VPAT
VPAT
VPAT
VPAT
with S Blade
with SU Blade
with VPAT Blade
with Angle Blade
VPAT
Ground Clearance**
VPAT
Straight
Angle Straight
Full 25° Angle
Semi-U
VPAT
Straight
Full 24° Angle
D6T XL
D6T XW
D6T LGP
Tier 4 Interim/Stage IIIB
153 kW
205 hp
153 kW
205 hp
153 kW
205 hp
20 985 kg
46,263 lb
23 663 kg
52,167 lb
C9.3 ACERT
1850
6
115 mm
4.5"
149 mm
5.9"
9.3 L
567 in3
7
7
560 mm
22"
560 mm
22"
2.86 m
9'5"
2.86 m
9'5"
4929 in2
3.20 m2
3.20 m2
4929 in2
1.88 m
74"
2.13 m
84"
21 788 kg
48,034 lb
24 118 kg
53,170 lb
C9.3 ACERT
1850
6
115 mm
4.5"
149 mm
5.9"
9.3 L
567 in3
7
8
760 mm
30"
710 mm
28"
2.86 m
9'5"
3.27 m
10'9"
4.35 m2
6738 in2
4.64 m2
7197 in2
2.03 m
80"
2.29 m
90"
22 902 kg
50,490 lb
24 336 kg
53,651 lb
C9.3 ACERT
1850
6
115 mm
4.5"
149 mm
5.9"
9.3 L
567 in3
8
8
915 mm
36"
785 mm
31"
3.27 m
10'9"
3.27 m
10'9"
5.98 m2
9275 in2
5.13 m2
7956 in2
2.29 m
90"
2.29 m
90"
2.46 m
2.46 m
3.11 m
3.11 m
3.15 m
3.15 m
3.89 m
3.89 m
8'1"
8'1"
10'2"
10'2"
10'4"
10'4"
12'9"
12'9"
2.46 m
2.51 m
3.11 m
3.16 m
3.15 m
3.20 m
3.89 m
4.25 m
17'6"
17'8"
17'1"
8'8"
8'0"
8'10"
1'3"
1'3"
5.33 m
5.53 m
5.29 m
2.95 m
2.79 m
3.00 m
384 mm
434 mm
4.16 m
3.77 m
3.26 m
13'8"
12'5"
12'8"
4.52 m
4.11 m
3.56 m
14'10"
13'6"
11'8"
3.88 m
3.49 m
425 L
12'9"
11'5"
112 U.S. gal
4.16 m
3.72 m
425 L
13'8"
12'2"
112 U.S. gal
—
5.33 m
5.39 m
5.21 m
2.64 m
2.44 m
2.69 m
384 mm
384 mm
8'1"
8'3"
10'2"
10'4"
10'4"
10'6"
12'9"
13'11"
—
—
17'6"
18'2"
17'4"
9'8"
9'2"
9'10"
1'3"
1'5"
—
2.51 m
2.51 m
3.16 m
3.16 m
3.20 m
3.20 m
4.25 m
4.25 m
5.50 m
8'3"
8'3"
10'4"
10'4"
10'6"
10'6"
13'11"
13'11"
18'1"
—
5.53 m
5.81 m
3.43 m
3.21 m
3.08 m
434 mm
434 mm
18'2"
19'1"
11'3"
10'6"
10'1"
1'5"
1'5"
4.06 m
5.07 m
4.63 m
13'4"
16'8"
15'2"
—
4.16 m
3.72 m
425 L
13'8"
12'2"
112 U.S. gal
***Operating weight includes cab, operator, lubricants, coolant, full fuel tank, standard track, hydraulic controls and fluid, SU blade and drawbar.
Edition 44
19-11
12/20/13 8:57 AM
Track-Type Tractors
Specifications
MODEL
Advertised Flywheel Power
D7E
D7E LGP
175 kW
235 hp
175 kW
57,441 lb
28 525 kg
235 hp
Operating Weight:*
Electric Drive Differential Steer
26 055 kg
Engine Model
Advertised Engine RPM
No. of Cylinders
62,886 lb
C9.3 ACERT
C9.3 ACERT
1700
1700
6
6
Bore
115 mm
4.5"
115 mm
4.5"
Stroke
149 mm
5.9"
149 mm
5.9"
567 in3
9.3 L
Displacement
9.3 L
7
567 in3
8
610 mm
24"
915 mm
36"
3.02 m
9'11"
3.45 m
11'4"
3.68 m2
5698 in2
6.31 m2
9792 in2
Track Gauge
1.98 m
6'6"
2.29 m
7'6"
3.32 m
10'11"
3.32 m
10'11"
4.88 m
16'0"
4.88 m
16'0"
with S Blade
5.86 m
19'3"
5.56 m
with SU Blade
6.07 m
19'11"
2.88 m
9'5"
3.42 m
11'3"
Width (w/o Trunnion — Std. Shoe)
2.59 m
8'6"
3.2 m
10'6"
472 mm
18.6"
472 mm
18.6"
Straight
3.9 m
12'10"
4.54 m
Angle Straight
4.5 m
14'9"
—
GENERAL DIMENSIONS:
Ground Clearance
18'3"
—
14'11"
Full 25° Angle
4.12 m
13'6"
—
Universal
3.99 m
13'1"
—
Semi-U
3.71 m
12'2"
409 L
108 U.S. gal
—
409 L
108 U.S. gal
**Operating weight includes cab, operator, lubricants, coolant, full fuel tank, standard track, hydraulic controls and fluid, SU blade and drawbar.
**Dimensions measured from ground line. Add grouser height for total dimension on hard surfaces.
Cat D7E — Resourceful in every way
● The D7E is designed to maximize efficiency and productivity while conserving natural resources.
●
Burns 10–30% less fuel per hour than previous models. Less fuel burned means reduced emissions.
●
The D7E earned a 2009 Clean Air Excellence Award from the U.S. Environmental Protection Agency.
●
More efficient – 25% more material moved per liter/gallon of fuel.
●
Fewer parts and longer component life, less fuel and fluids, means less to replace and less to dispose.
●
Major structures and components are built to be rebuilt, reducing waste and replacement costs.
19-12
Edition 44
12/20/13 8:57 AM
Specifications
Track-Type Tractors
19
MODEL
Flywheel Power
D7R
179 kW
D7R XR
240 hp
179 kW
56,129 lb
27 002 kg
240 hp
Operating Weight:*
25 455 kg
Engine Model
Rated Engine RPM
No. of Cylinders
59,540 lb
C9 ACERT
C9 ACERT
2100
2100
6
6
Bore
112 mm
4.4"
112 mm
4.4"
Stroke
149 mm
5.9"
149 mm
5.9"
8.8 L
537 in3
8.8 L
537 in3
560 mm
22"
560 mm
22"
2.87 m
9'5"
3.05 m
10'0"
3.22 m2
4991 in2
3.42 m2
5295 in2
1980 mm
6'6"
1980 mm
6'6"
Displacement
Track Gauge
7
8
GENERAL DIMENSIONS:
2.58 m
8'6"
2.58 m
8'6"
3.29 m
10'9"
3.29 m
10'9"
3.28 m
10'9"
3.28 m
10'9"
4.73 m
15'6"
4.73 m
15'6"
with S Blade
—
—
2.88 m
9'5"
2.88 m
2.54 m
8'4"
2.54 m
8'4"
415 mm
1'4"
415 mm
1'4"
3.69 m
12'2"
3.69 m
12'2"
481 L
127 U.S. gal
481 L
127 U.S. gal
Ground Clearance
9'5"
Semi-U
Major structures and components are built to be rebuilt, reducing waste and replacement costs.
Edition 44
19-13
12/20/13 8:57 AM
Track-Type Tractors
Specifications
MODEL
Flywheel Power
D7R LGP
D8R
D8R LGP
179 kW
240 hp
226 kW
303 hp
226 kW
303 hp
27 626 kg
60,916 lb
37 920 kg
83,600 lb
35 176 kg
77,550 lb
Operating Weight:*
Engine Model
C9 ACERT
3406C TA
3406C TA
2100
2100
2100
6
6
Rated Engine RPM
No. of Cylinders
6
Bore
112 mm
4.4"
137 mm
5.4"
137 mm
Stroke
149 mm
5.9"
165 mm
6.5"
165 mm
6.5"
8.8 L
537 in3
14.6 L
893 in3
14.6 L
893 in3
914 mm
36"
610 mm
24"
965 mm
38"
3.16 m
10'5"
3.21 m
10'6"
3.26 m
10'8"
5.78 m2
8960 in2
3.91 m2
6062 in2
6.3 m2
9746 in2
2235 mm
7'4"
2.08 m
6'10"
2.34 m
7'8"
Displacement
Track Gauge
7
8
5.4"
8
GENERAL DIMENSIONS:
2.7 m
8'10"
2.67 m
8'9"
2.67 m
8'9"
3.37 m
11'1"
3.45 m
11'4"
3.51 m
11'6"
3.36 m
11'0"
3.42 m
11'3"
3.49 m
11'5"
6.80 m
22'4"
6.80 m
22'4"
16'3"
4.96 m
Overall Length (with SU Blade)†
—
(without Blade)
with S Blade
—
4.96 m
4.73 m
15'6"
—
16'3"
—
5.81 m
19'1"
3.37 m
11'1"
3.05 m
10'0"
3.38 m
11'1"
3.15 m
10'4"
2.70 m
8'8"
3.30 m
10'10"
495 mm
1'7"
613 mm
2'0"
606 mm
2'0"
Ground Clearance
—
—
Straight
4.55 m
Angle Straight
14'11"
—
—
—
4.99 m
16'4"
—
Full 25° Angle
—
4.52 m
14'10"
—
Universal
—
4.26 m
14'0"
—
Semi-U
—
481 L
127 U.S. gal
3.94 m
12'11"
4.40 m
14'5"
625 L
165 U.S. gal
625 L
165 U.S. gal
— D8R equipped with track guides, ROPS/FOPS cab, single shank ripper and SU blade.
†Includes drawbar.
Cat tractors are designed for ease of serviceability, with features like ground-level service points and wide engine
enclosure doors.
19-14
Edition 44
12/20/13 8:57 AM
Specifications
Track-Type Tractors
19
MODEL
D8T
D8T LGP
D8T
D8T LGP
—
—
Tier 4 Interim/
Stage IIIB
Tier 4 Interim/
Stage IIIB
Flywheel Power
231 kW
310 hp
231 kW
310 hp
237 kW
317 hp
237 kW
317 hp
39 751 kg
87,650 lb
37 750 kg
83,224 lb
39 795 kg
87,733 lb
37 795 kg
83,324 lb
Operating Weight:*
Engine Model
C15 ACERT
C15 ACERT
C15 ACERT
C15 ACERT
1850
1850
1850
1850
6
6
6
Rated Engine RPM
No. of Cylinders
6
Bore
137 mm
5.4"
137 mm
5.4"
137 mm
5.4"
137 mm
5.4"
Stroke
172 mm
6.75"
172 mm
6.75"
172 mm
6.75"
172 mm
6.75"
928 in3
15.2 L
928 in3
15.2 L
928 in3
15.2 L
Displacement
15.2 L
8
8
8
928 in3
8
610 mm
24"
965 mm
38"
610 mm
24"
965 mm
38"
3.21 m
10'6"
3.20 m
10'6"
3.21 m
10'6"
3.21 m
10'6"
Ground Contact Area
(w/Std. Shoe)
3.91 m2
6062 in2
6.19 m2
9593 in2
3.91 m2
6062 in2
6.19 m2
9593 in2
Track Gauge
2.08 m
6'10"
2.34 m
7'8"
2.08 m
6'10"
2.34 m
7'8"
2.67 m
8'9"
2.67 m
8'9"
GENERAL DIMENSIONS:
—
—
Height**
(To Top of ROPS Canopy)
3.46 m
11'4"
3.45 m
11'4"
3.46 m
11'4"
3.46 m
11'4"
3.51 m
11'6"
3.51 m
11'6"
6.09 m
20'0"
6.09 m
20'0"
6.09 m
20'0"
6.09 m
20'0"
4.64 m
15'3"
4.98 m
16'4"
4.64 m
15'3"
4.98 m
16'4"
3.06 m
10'0"
3.38 m
11'1"
3.06 m
10'0"
3.38 m
11'1"
2.64 m
8'8"
3.30 m
10'10"
2.64 m
8'8"
3.30 m
10'10"
613 mm
2'0"
613 mm
2'0"
613 mm
2'0"
613 mm
2'0"
(without Blade)
Width (w/o Trunnion —
Std. Shoe)
Ground Clearance
—
—
Angle Straight
4.99 m
16'4"
—
4.99 m
16'4"
—
Full 25° Angle
4.52 m
14'10"
—
4.52 m
14'10"
—
Universal
4.26 m
14'0"
4.26 m
14'0"
Semi-U
3.94 m
12'11"
4.40 m
14'5"
3.94 m
12'11"
4.40 m
14'5"
643 L
170
U.S. gal
643 L
170
U.S. gal
643 L
170
U.S. gal
643 L
170
U.S. gal
—
—
***Operating weight includes ROPS/FOPS cab, operator, lubricants, coolant, full fuel tank, standard track, hydraulic controls and fluid, SU blade and ripper.
LGP operating weight includes drawbar instead of ripper.
Cat engines with ACERT Technology provide powerful reliability, while meeting the stringent emissions standards.
Edition 44
19-15
12/20/13 8:57 AM
Track-Type Tractors
Specifications
MODEL
Flywheel Power
D9R
D9T
D9T
—
—
Tier 4 Final
325 kW
436 hp
302 kW
405 hp
306 kW
410 hp
Operating Weight:*
Power Shift Clutch Brake
48 784 kg
Engine Model
107,548 lb
—
—
47 872 kg
—
105,539 lb
48 361 kg
106,618 lb
3408C SCAC
C18 ACERT
C18 ACERT
1900
1833
1800
8
6
Rated Engine RPM
No. of Cylinders
6
Bore
137 mm
5.4"
145 mm
5.7"
145 mm
Stroke
152 mm
6"
183 mm
7.2"
183 mm
7.2"
18 L
1099 in3
18.1 L
1104 in3
18.1 L
1104 in3
610 mm
24"
610 mm
24"
610 mm
24"
3.47 m
11'5"
3.47 m
11'5"
3.47 m
11'5"
4.24 m2
6569 in2
4.24 m2
6569 in2
4.24 m2
6569 in2
Track Gauge
2.25 m
7'5"
2.25 m
7'5"
2.25 m
7'5"
Displacement
8
8
5.7"
8
GENERAL DIMENSIONS:
3.00 m
9'10"
3.99 m
13'1"
4.00 m
13'1"
4.00 m
13'1"
Height** (To Top of FOPS Cab)
3.82 m
12'6"
3.82 m
12'6"
3.82 m
12'6"
6.84 m
22'5"
—
5.18 m
17'0"
—
(without Blade)
—
—
—
—
(with SU Blade and Ripper)
—
8.33 m
26'11"
8.33 m
(without Blade and Ripper)
—
4.91 m
16'1"
4.91 m
16'1"
3.31 m
10'11"
3.31 m
10'11"
Ground Clearance
3.30 m
10'10"
26'11"
2.93 m
9'8"
2.87 m
9'5"
2.87 m
9'5"
591 mm
1'11"■
596 mm
1'11"
596 mm
1'11"
Universal
4.65 m
15'3"
4.65 m
15'3"
4.65 m
15'3"
Semi-U
4.31 m
14'2"
4.31 m
14'2"
4.31 m
14'2"
216 U.S. gal
889 L
235 U.S. gal
821 L
217 U.S. gal
36 L
9.5 U.S. gal
DEF Tank Capacity
818 L
—
—
***Operating weight includes ROPS canopy, operator, lubricants, coolant, full fuel tank, hydraulic controls and fluids, semi universal blade with tilt, back-up
alarm, seat belts, lights, and single shank ripper.
***— D9R equipped with track guides, ROPS/FOPS cab, single shank ripper and SU blade.
*■ SAE J1234.
19-16
Edition 44
12/20/13 8:57 AM
Specifications
Track-Type Tractors
19
MODEL
Flywheel Power
Reverse Gears
D10T2
D11T
447 kW
600 hp
538 kW
722 hp
70 171 kg
154,700 lb
634 kW
D11T CD
850 hp
634 kW
850 hp
—
—
Operating Weight:*
Power Shift Clutch Brake
Engine Model
104 300 kg
229,800 lb
112 700 kg
248,500 lb
C27 ACERT
C32 ACERT
C32 ACERT
1800
1800
1800
12
12
Rated Engine RPM
No. of Cylinders
12
Bore
137 mm
5.4"
145 mm
5.71"
145 mm
5.71"
Stroke
152 mm
6"
162 mm
6.38"
162 mm
6.38"
1648 in3
32.1 L
1959 in3
32.1 L
Displacement
27 L
8
8
1959 in3
8
610 mm
24"
710 mm
28"
915 mm
36"
Length of Track on Ground (Idler to Idler)
3.88 m
12'9"
4.44 m
14'7"
4.44 m
14'7"
4.74 m2
7347 in2
6.31 m2
9781 in2
8.13 m2
12,605 in2
Track Gauge
2.55 m
8'4"
2.89 m
9'6"
2.89 m
9'6"
GENERAL DIMENSIONS:
Height (Stripped Top)**
3.222 m
10'7"
3.64 m
11'11"
3.64 m
11'11"
4.41 m
14'5"
4.60 m
15'1"
4.60 m
15'1"
Height (To Top of FOPS Cab)
4.10 m
13'5"
4.29 m
14'1"
4.29 m
14'1"
(with SU Blade and SS Ripper)***
9.16 m
30'1"
10.59 m
34'9"
10.70 m
35'1"
(without Blade and Ripper)†
5.331 m
17'6"
6.03 m
19'9"
6.03 m
19'9"
3.74 m
12'3"
4.38 m
14'4"
4.38 m
14'4"
3.30 m
10'10"
3.78 m
12'5"
3.81 m
12'6"
664 mm
2'2"
675 mm
2'3"
675 mm
2'3"
17'3"
6.36 m
Overall Length:
Ground Clearance
CarryDozer
—
—
6.71 m
5.26 m
Semi-U
4.86 m
15'11"
5.60 m
18'4"
1204 L
314 U.S. gal
1609 L
425 U.S. gal
1609 L
425 U.S. gal
1987 L
505 U.S. gal
1987 L
505 U.S. gal
Fuel Tank Refill Capacity (Extra Capacity)
—
20'10"
22'0"
Universal
—
—
***Operating weight includes coolant, lubricants, full fuel tank, ROPS, FOPS cab, SU ABR bulldozer (D10T2) or U ABR bulldozer (D11T), dual tilt, single-shank
ripper with pin-puller, fast fuel, standard ES shoes, and operator.
D11T CD has 11 Carrydozer and single-shank Carrydozer ripper.
***Height (Stripped Top) — without ROPS canopy, cab, exhaust, lift cylinders, seat back or other easily removed encumbrances.
***Overall length of D11T CD includes Straight (CarryDozer) Blade and SS Ripper.
†Overall length of machine from front tag link trunion to rigid drawbar and excludes track grouser height.
All dimensions are approximate.
Edition 44
19-17
12/20/13 8:57 AM
Track-Type Tractors
Drawbar Pull vs. Ground Speed
● Hydrostatic Drive
D3K XL (LRC)
D3K LGP (LRC)
NOTES: Usable pull will depend upon weight and
traction of equipped tractor.
lb × N ×
1000 1000
Assumes sufficient machine weight for
<5% track slip at POR pressure.
140
Assumes pumps and motors are broken in.
29.3
DRAWBAR PULL
120
Assumes nominal engine power and valve
settings.
24.8
100
Drawbar pull at track stall will be lower.
20.3
80
15.8
60
11.3
40
6.8
20
2.3
0
1
0
3
1.2
5
2.5
7
3.7
9
km/h
6.2 mph
9
km/h
6.2 mph
5.0
SPEED
D4K XL (LRC)
D4K LGP (LRC)
lb × N ×
1000 1000
180
38.3
160
33.8
140
DRAWBAR PULL
29.3
120
24.8
100
20.3
80
15.8
60
11.3
40
6.8
20
2.3
0
1
0
3
1.2
5
2.5
7
3.7
5.0
SPEED
19-18
Edition 44
12/20/13 8:57 AM
● Hydrostatic Drive
D5K XL (LRC)
D5K LGP (LRC)
Track-Type Tractors
19
NOTES: Usable pull will depend upon weight and
lb × N ×
1000 1000
180
38.3
Assumes sufficient machine weight for
<5% track slip at POR pressure.
160
Assumes pumps and motors are broken in.
140
Assumes nominal engine power and valve
settings.
120
Drawbar pull at track stall will be lower.
33.8
DRAWBAR PULL
29.3
24.8
100
20.3
80
15.8
60
11.3
40
6.8
20
2.3
0
1
0
3
5
1.2
2.5
7
3.7
9
5.0
km/h
6.2 mph
SPEED
D6K XL/D6K LGP (LRC)
D6K2 XL/D6K2 LGP (HRC)
N×
1000
250
lb ×
1000
55
DRAWBAR PULL
50
200
45
40
150
100
35
30
25
20
15
50
10
5
0
0
0
0
1
2
2
3
4
4
6
5
8
6
7 mph
10
km/h
SPEED
Edition 44
19-19
12/20/13 8:57 AM
Track-Type Tractors
● Power Shift
D6N and D5R XL/LGP
D6R
N × lb ×
1000 1000
80
350
250
200
400
60
1
50
40
150
30
100
20
50
0
2
3
10
0
N×
1000
80
70
DRAWBAR PULL
DRAWBAR PULL
300
lb ×
1000
0
0
1
2
2
3
4
4
6
1F
300
60
200
40
20
2F
100
3F
5
8
6
10
8 mph
7
12
0
km/h
SPEED
0
0
0
2
1
4
2
6
3
8
4
5
10
6
12
7
km/h
mph
SPEED
D6T XL/XW/LGP
DRAWBAR PULL
lb
KEY
mph
–––– STD
- - - - XL/LGP
SPEED
NOTE: Usable pull will depend upon weight and
19-20
Edition 44
12/20/13 8:57 AM
● Power Shift
D6T Tier 4 Interim/Stage IIIB XL
40
lb × kg ×
1000 1000
90
DRAWBAR PULL
80
30
70
60
50
20
40
30
10
20
100
80
60
40
10
0
2.0
0
1
0
2
2.5
3
2
4
4
5
6
30
20
0
0
0
0
2
1
10
4
2
6
3
8
4
5
10
6
12 km/h
7
mph
SPEED
7 mph
6
8
40
10
3.5
3.0
50
20
1.0
0
19
D7E
lb ×
1000
DRAWBAR PULL
kg ×
1000
Track-Type Tractors
km/h
SPEED
D7R Standard/XR/LGP
Differential Steer
kg ×
1000
60
lb ×
1000
140
DRAWBAR PULL
120
50
40
30
1
100
80
2
60
20
40
10
20
0
0
KEY
3
0
0
1 — 1st Gear
2 — 2nd Gear
3 — 3rd Gear
1
2
2
3
4
4
6
5
8
6
10
7
8 mph
12
km/h
SPEED
Edition 44
19-21
12/20/13 8:57 AM
Track-Type Tractors
● Power Shift
D8R
D8R LGP
D8T
D8T LGP
kg × lb ×
1000 1000
70
kg × lb ×
1000 1000
160
140
60
140
120
120
50
100
40
80
2
30
60
20
1
50
1
DRAWBAR PULL
DRAWBAR PULL
60
100
40
80
30
60
20
40
2
40
3
10
20
0
0
0
1
0
2
2
3
4
4
5
6
6
8
20
0
0
8 mph
7
10
10
12
3
0
0
km/h
1
2
2
3
4
4
6
5
8
6
10
7 mph
km/h
SPEED
SPEED
D9R Power Shift with
Steering Clutches and Brakes
kg × lb ×
1000 1000
180
80
70
1
160
DRAWBAR PULL
140
60
120
50
100
2
40
KEY
80
30
20
60
1 — 1st Gear
2 — 2nd Gear
3 — 3rd Gear
3
40
10
20
0
0
0
0
1
2
2
3
4
4
6
5
8
6
8 mph
7
10
12
km/h
SPEED
19-22
Edition 44
12/20/13 8:57 AM
● Power Shift
D9T Differential Steering
70
kg ×
1000
100
1
DRAWBAR PULL
DRAWBAR PULL
60
120
50
100
40
80
30
2
40
10
20
0
0
80
70
150
2
60
50
100
40
50
10
0
0
0
1
0
2
3
2
4
4
5
6
3
30
20
3
1
200
90
140
20
lb ×
1000
250
110
60
19
D10T2
kg × lb ×
1000 1000
180
80
160
Track-Type Tractors
6
8
7
10
8 mph
12
km/h
0
0
SPEED
1
2
2
3
4
4
6
5
8
6
7
10
8 mph
12
km/h
SPEED
D11T/D11T CD
kg ×
1000
lb ×
1000
350
150
1
140
300
130
120
DRAWBAR PULL
110
250
100
90
KEY
200
80
70
2
1 — 1st Gear
2 — 2nd Gear
3 — 3rd Gear
3
traction of equipped tractor. Tractors with
suspended undercarriage can provide up
to 15% more tractive effort than tractors
with non-suspended undercarriage.
150
60
50
100
40
30
20
50
10
0
0
0
0
1
2
2
3
4
4
6
5
8
6
8 mph
7
10
12
km/h
SPEED
Edition 44
19-23
12/20/13 8:57 AM
Track-Type Tractors
Travel Speed
TRAVEL SPEED
POWER SHIFT
D3K (LRC)
MODEL
All Models
HYDROSTATIC km/h
mph
FORWARD
9.0
5.6
REVERSE
10.0
6.2
D3K2
All Models
km/h
mph
9.0
5.6
10.0
6.2
D4K (LRC)
All Models
km/h
mph
9.0
5.6
10.0
6.2
D4K2
All Models
km/h
mph
9.0
5.6
10.0
6.2
POWER SHIFT
D5K (LRC)
MODEL
All Models
HYDROSTATIC km/h
mph
FORWARD
9.0
5.6
REVERSE
10.0
6.2
D5K2
All Models
km/h
mph
9.0
5.6
10.0
6.2
D6K (LRC)
All Models
km/h
mph
10.0
6.2
10.0
6.2
D6K2
All Models
km/h
mph
10.0
6.2
10.0
6.2
Differential
Steer
D5R
km/h
mph
3.1
1.93
5.7
3.54
10.0
6.21
D6N/
D6N Tier 4
Interim/
Stage IIIB
km/h
mph
3.1
1.9
5.7
3.5
10.0
6.2
Differential
Steer
D6R
km/h
mph
3.8
2.3
6.6
4.1
7.1
11.5
D6T
km/h
mph
3.8
2.3
6.5
4.0
11.3
7.0
POWER SHIFT
MODEL
FORWARD
1
2
3
REVERSE
1
2
3
ELECTRIC
FORWARD
REVERSE
19-24
D7E
km/h
mph
—
—
—
—
—
—
D7E LGP
km/h
mph
—
—
—
—
—
—
D7R
km/h
mph
3.52
2.19
6.10
3.79
10.54
6.55
3.1
6.4
11.6
1.93
4.00
7.21
3.1
6.4
11.6
1.9
4.0
7.2
4.8
8.4
14.6
3.0
5.2
9.1
4.7
8.3
14.6
2.9
5.1
9.0
—
—
—
—
—
—
—
—
—
—
—
—
4.54
7.85
13.58
2.82
4.88
8.44
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
11.3
11.3
7.0
7.0
11.3
11.3
7.0
7.0
—
—
—
—
Edition 44
12/20/13 8:57 AM
Travel Speed
Track-Type Tractors
19
TRAVEL SPEED
POWER SHIFT
MODEL
FORWARD
1
2
3
REVERSE
1
2
3
GEAR
FORWARD
1.5
2
2.5
3
3.5
REVERSE
1.5
2
2.5
3
3.5
Differential
Steer
D8R
km/h
mph
3.5
2.2
6.2
3.9
10.8
6.7
4.7
8.1
13.9
2.9
5.0
8.6
D8T
km/h
mph
3.4
2.1
6.0
3.7
10.6
6.6
4.5
7.9
14.2
2.8
4.9
8.8
D6T
Powershift with
Multi Velocity Program
km/h
mph
3.8
2.3
5.1
3.2
6.6
4.1
8.5
5.3
11.4
7.1
4.8
6.6
8.4
11.0
14.6
3.0
4.1
5.2
6.8
9.0
D9R
km/h
mph
3.8
2.4
6.8
4.2
11.9
7.4
4.7
8.4
14.7
2.9
5.2
9.1
D9T
km/h
mph
3.9
2.4
6.8
4.2
11.7
7.3
4.7
8.4
14.3
2.9
5.2
8.9
D10T2
km/h
mph
4.0
2.5
7.2
4.5
12.7
7.9
5.2
9.0
15.8
3.2
5.6
9.8
D11T/CD
km/h
mph
3.9
2.4
6.8
4.2
11.8
7.3
4.7
8.2
14.0
2.9
5.1
8.7
D11T/CD
High Altitude
km/h
mph
4.0
2.5
7.0
4.4
12.0
7.5
4.8
8.3
14.9
D6T
Powershift with Multi
Velocity Program — Sound
Suppressed
km/h
mph
3.2
2.0
5.1
3.2
6.3
3.9
8.5
5.3
10.9
6.8
3.9
6.6
8.0
11.0
13.8
2.4
4.1
5.0
6.8
8.6
Edition 44
3.0
5.2
9.0
19-25
12/20/13 8:57 AM
Track-Type Tractors
Ground Pressures
GROUND PRESSURES
Pressures computed from operating weights given
earlier in this section in the specifications tables.
MODEL
D3K XL (LRC)
D3K LGP (LRC)
D3K2 XL
D3K2 LGP
D4K XL (LRC)
D4K LGP (LRC)
D4K2 XL
D4K2 LGP
D5K XL (LRC)
D5K LGP (LRC)
D5K2 XL
D5K2 LGP
D5R XL
D5R LGP
D6K XL (LRC)
(Standard shoe)
D6K LGP (LRC)
(Standard shoe)
D6K2 XL
D6K2 LGP
D6N XL (DS)
(Standard shoe)
D6N LGP (DS)
(Standard shoe)
D6N Super LGP
D6N XL
Tier 4 Interim/
Stage IIIB
D6N LGP
Tier 4 Interim/
Stage IIIB
SHOE
WIDTH
CONTACT GROUND
AREA PRESSURE
mm
406
635
406
635
460
635
460
635
510
660
510
660
560
610
840
865
510
560
610
760
560
760
560
610
865
840
950
1070
610
in
16
25
16
25
18
25
18
25
20
26
20
26
22
24
33
34
20
22
24
30
22
30
22
24
34
33
37
42
24
m2
1.70
2.70
1.70
2.70
2.10
2.90
2.10
2.90
2.40
3.00
2.40
3.00
2.89
3.18
5.24
5.39
2.70
3.00
3.20
4.00
3.00
4.00
2.89
3.18
5.39
5.22
5.90
6.70
3.18
840
33
5.22
in2
2637
4124
2637
4124
3206
4425
3206
4425
3652
4726
3652
4726
4480
4929
8117
8385
4185
4650
4960
6200
4650
6200
4480
4929
8358
8107
9179
10,339
4929
kPa
44.80
29.70
44.80
29.70
38.60
29.20
38.60
29.20
39.10
31.10
39.10
31.10
56.54
51.43
33.72
32.75
46.82
42.13
41.30
33.02
39.80
30.70
56.54
52.30
32.75
34.40
27.02
24.37
51.70
psi
6.50
4.30
6.50
4.30
5.60
4.24
5.60
4.24
5.67
4.52
5.67
4.52
8.20
7.46
4.89
4.75
6.79
6.11
5.99
4.79
5.77
4.45
8.20
7.58
4.75
4.99
3.92
3.53
7.49
8107 34.20
4.96
MODEL
D6R
D6R XL
D6R LGP
D6T
D6T XL
D6T XL
(Tier 4 Interim/
Stage IIIB)
D6T XW
(Tier 4 Interim/
Stage IIIB)
D6T LGP
(Tier 4 Interim/
Stage IIIB)
SHOE
WIDTH
CONTACT GROUND
AREA
PRESSURE
mm
560
610
560
610
915
991
560
610
560
610
560
610
in
22
24
22
24
36
39
22
24
22
24
22
24
m2
2.92
3.19
3.15
3.44
5.94
6.43
2.92
3.19
3.15
3.44
3.20
3.49
in2
4531
4943
4878
5321
9204
9968
4531
4943
4878
5321
4922
5369
kPa
61.48
56.35
62.57
57.63
35.86
33.11
65.19
59.76
63.73
58.43
64.66
59.28
psi
8.92
8.17
9.08
8.32
5.20
4.80
9.46
8.67
9.24
8.47
9.38
8.60
610
710
760
760
915
991
24
28
30
30
36
39
3.48
5390
4.06
6289
4.35
6738
4.98
7729
5.98
9275
6.48 10,048
61.45
52.66
49.15
44.15
36.79
33.96
8.91
7.64
7.13
6.40
5.34
4.93
NOTE: Ground contact area = width of track shoe
× length of track on ground × 2.
Ground pressure =
operating weight
ground contact area
DS — Differential Steer
19-26
Edition 44
12/20/13 8:57 AM
Ground Pressures
Track-Type Tractors
19
GROUND PRESSURES
Pressures computed from operating weights given
earlier in this section in the specifications tables.
SHOE
WIDTH
MODEL
D7E
◀
Tier 4
Interim/
Stage IIIB
D7E LGP
Tier 4 Interim/
Stage IIIB
◀
D7R
D7R XR
◀
D7R LGP
D8R
◀
D8R LGP
D8T
◀
D8T LGP
D8T
Tier 4 Interim/
Stage IIIB
D8T LGP
Tier 4 Interim/
Stage IIIB
◀ Standard
CONTACT GROUND
AREA PRESSURE
mm
560
610
660
in
22
24
26
m2
3.37
3.68
3.98
in2
kPa
psi
5231 75.71 10.98
5698 69.51 10.08
6165 64.24 9.32
915
36
6.31
9792 44.28
560
610
560
610
914
610
660
710
965
610
660
710
965
610
660
710
965
22
24
22
24
36
24
26
28
38
24
26
28
38
24
26
28
38
3.24
3.53
3.43
3.75
5.82
3.91
4.23
4.55
6.29
3.91
4.23
4.55
6.19
3.91
4.23
4.55
6.19
5016
5472
5315
5808
9029
6062
6559
7056
9746
6062
6559
7056
9593
6062
6559
7056
9593
75.10
69.00
70.60
65.90
45.50
95.11
87.90
81.48
54.88
99.69
92.14
85.65
59.83
99.81
92.25
85.75
59.90
6.42
10.56
9.76
10.03
9.26
6.48
13.79
12.75
11.81
7.96
14.46
13.36
12.42
8.68
14.47
13.38
12.43
8.68
SHOE
WIDTH
MODEL
D9R/D9T
◀
D10T2
◀
D11T
◀
D11T CD
◀
mm
560
610
685
760
610
710
760
710
810
915
810
915
CONTACT GROUND
AREA PRESSURE
in
22
24
27
30
24
28
30
28
32
36
32
36
m2
in2
kPa
psi
3.89
6031 121.8 17.67
4.24
6569 111.80 16.22
4.74
7374 99.60 14.45
5.28
8185 89.80 13.02
4.74
7347 145.25 21.06
5.52
8551 124.49 18.06
5.91
9153 116.19 16.85
6.31
9781 161.98 23.49
7.20 11,159 141.99 20.59
8.13 12,605 125.69 18.23
7.20 11,159 153.54 22.27
8.13 12,605 135.92 19.71
NOTE: Ground contact area = width of track shoe
× length of track on ground × 2.
Ground pressure =
operating weight
ground contact area
shoe.
Edition 44
19-27
12/20/13 8:57 AM
Track-Type Tractors
Extreme Slope Operation
EXTREME SLOPE OPERATION
The maximum fore and aft grade in static condition
on which each track-type tractor or pipelayer will maintain proper lubrication is 45 degrees (100%). Consult
Operation & Maintenance Manual (if applicable) for
POWER TRAIN fluid level overfill requirements for
operation on extreme slopes. Extreme slope operation
is anytime the slope exceeds 25° (47%).
The ENGINE should never be overfilled with oil. This
may lead to rapid overheating. For extreme slope operation, engine oil should be maintained at the full mark.
When working sidehills and slopes, consideration
should be given to the following important points:
●
Implements hitched to the drawbar — This may decrease
weight on uphill track, e.g., logging arch, two-wheel
wagon.
●
Height of hitch on tractor — When a high drawbar is
used the tractor is less stable than with the standard
drawbar.
●
Width of shoes — Wide track shoes tend to decrease
“digging in”, hence tractor is more stable.
●
Operated equipment — Be aware of the stability and
other performance features of the equipment operated
by the tractor.
●
Keep all attachments or pulled loads low to the ground
for optimum stability.
●
Speed of travel — At higher speeds, inertia forces tend
to make the tractor less stable.
●
Roughness of terrain or surface — Ample allowance
should be made where the terrain or surface is uneven.
●
Mounted equipment — Bulldozers, sidebooms, winches,
and other mounted equipment cause the tractor to
balance differently.
●
●
Nature of surface — New earthen fills may give way
with the weight of the tractor. Rocky surfaces may promote side slipping of tractor.
Track slippage due to excessive loads — This may
cause downhill track to “dig in,” increasing angle of
tractor.
NOTE: Both ENGINE and POWER TRAIN fluid levels
should be checked on level ground before working sidehills and slopes.
NOTE: Safe operation on steep slopes may require special machine maintenance as well as excellent operator
skill and proper equipment for the specific application. Consult Operation & Maintenance Manual
(if applicable) for proper fluid level requirements.
19-28
Edition 44
12/20/13 8:57 AM
19
HYDRAULIC CONTROLS
CONTENTS
Features:
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19-29
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19-30
●
Designed and built for specific tractor applications.
Valves and components sized for exacting quality
and performance.
●
Job requirements matched through various arrangements.
●
Hydraulic blade and ripper controls: Mechanical controls on G Series. Electro hydraulic controls on D6N
and D6K/D6K2. Pilot blade and ripper controls on
D6T Tier 3 with optional electro hydraulic blade control. Electro hydraulic blade and ripper controls on
D6T Tier 4 Interim/Stage IIIB. Mechanical controls
on D9R. Electro hydraulic blade and ripper controls
on D7E, D8T, D9T, D10T2, and D11T.
●
Full flow filters*… all oil completely filtered.
●
Dual tilt — standard on D11T and D11T CD, attachment option on D7E, D8R, D8T, D9R, D9T, D10T2.
*Exception — D8R 2-pump.
Edition 44
PHB-Sec19-TTT-2-HydraulicControls(pg29-32).indd 29
19-29
12/20/13 8:57 AM
Hydraulic Controls
MODEL
Mounting Point
Number of Valves
Flow at 6890 kPa
(1000 psi)
Tank Capacity (Oil)
Lift Relief Valve Setting
Weight Installed:
4 Valves
MODEL
Specifications
D3K (LRC)
39 kg
86 lb*
MODEL
Mounting Point
Number of Valves
Flow at 6890 kPa
(1000 psi)
Tank Capacity (Oil)
Weight Installed:
2 Valves
3 Valves
39 kg
86 lb*
39 kg
86 lb*
39 kg
86 lb*
D5K2
D5R
D6K (LRC)
Fender
Right Rear Fender
Under Operator’s
Platform
3 or 4
120 L/min
31.7 gpm
@ 2100 RPM
58 L
15.3 U.S. gal
—
26 000 kPa
3771 psi
3 or 4
3 or 4
3 or 4
73.5 L/min
19.4 gpm
73.5 L/min
19.4 gpm
132.5 L/min
35.0 gpm
@ 2150 RPM
@ 2150 RPM
@ 2300 RPM
59.5 L
15.7 U.S. gal
59.5 L
15.7 U.S. gal
29.5 L
7.8 U.S. gal
20 600 kPa
2988 psi
20 600 kPa
2988 psi
—
—
—
27 500 kPa
3989 psi
—
39 kg
—
86 lb*
39 kg
86 lb*
D6N/
D6N Tier 4 Interim/
Stage IIIB
D6K2
Number of Valves
Flow at 6890 kPa
(1000 psi)
Tank Capacity (Oil)
XL and LGP
Weight Installed:
2 Valves
3 Valves
4 Valves
D4K2
Fender
MODEL
Mounting Point
D4K (LRC)
D5K (LRC)
Mounting Point
Number of Valves
Flow at 6890 kPa
(1000 psi)
Tank Capacity (Oil)
XL and LGP
Weight Installed:
3 Valves
4 Valves
D3K2
Fender
Fender
Fender
Fender
3 or 4
3 or 4
3 or 4
3 or 4
73.5 L/min
19.4 gpm
73.5 L/min
19.4 gpm
73.5 L/min
19.4 gpm
73.5 L/min
19.4 gpm
@ 2150 RPM
@ 2150 RPM
@ 2150 RPM
@ 2150 RPM
59.5 L
15.7 U.S. gal
59.5 L
15.7 U.S. gal
59.5 L
15.7 U.S. gal
59.5 L
15.7 U.S. gal
20 600 kPa
2988 psi
20 600 kPa
2988 psi
20 600 kPa
2988 psi
20 600 kPa
2988 psi
Under Operator’s
Right Rear Fender
Platform
3 or 4
3 or 4
120 L/min
31.7 gpm
132.5 L/min
35.0 gpm
@ 2100 RPM
@ 2300 RPM
58 L
15.3 U.S. gal
29.5 L
7.8 U.S. gal
—
—
26 000 kPa
3771 psi
27 500 kPa
3989 psi
—
30 kg
37 kg
—
66 lb
81.6 lb
D6T Tier 4 Interim/
Stage IIIB
Under Operator’s
Platform
2, 3, or 4
205 L/min
54 gpm
@ 2010 RPM
96 L
25.4 U.S. gal
19 300 kPa
2800 psi
Included in Std. Tractor
—
27 kg
32 kg
27 kg
32 kg
59.5 lb
70.5 lb
D6T VPAT
Tier 4 Interim/
Stage IIIB
66 lb
81.6 lb
D6R
(Differential Steer)
D6T
Under Operator’s
Platform
3 or 4
214 L/min
57 gpm
@ 2000 RPM
51.5 L
13.6 U.S. gal
19 305 kPa
2800 psi
—
Under Operator’s
Platform
2, 3, or 4
205 L/min
54 gpm
@ 2010 RPM
47.3 L
12.5 U.S. gal
19 300 kPa
2800 psi
—
311 kg
59.5 lb
70.5 lb
30 kg
37 kg
686 lb
—
—
—
—
D7E
Under Operator’s
Blade Control under
Platform
Hood, Ripper on Rear
3 or 4
2 Std. 4 with Ripper
205 L/min
54 gpm
204 L/min
54 gpm
@ 2010 RPM
@ 2124 RPM (PMP)
96 L
25.4 U.S. gal
66 L
17.4 U.S. gal
21 550 kPa
3125 psi
27 600 kPa
4000 psi
—
—
*Hydraulic tank not included.
NOTE: Weight installed, two valves, includes pump, tank with filters, valves, lines, linkage, oil cooler and control levers.
19-30
Edition 44
12/20/13 8:57 AM
Specifications
Hydraulic Controls
19
MODEL
Mounting Point
Number of Valves
Flow at 6890 kPa
(1000 psi)
Tank Capacity (Oil)
Weight Installed
MODEL
Mounting Point
Number of Valves
Flow at 6890 kPa
(1000 psi)
Tank Capacity (Oil)
Lift
Tilt
Weight Installed
D7R
D8R
D8T
D9R
Under Operator’s
Platform
2 or 3
Under Operator’s
Platform
2 Std.
4 with Ripper◀
Pilot Control System
Under Operator’s
Platform
4
+ Dual Tilt (Attach.)
Radiator Guard
289 L/min
76 gpm
@ 2100 RPM
54 L
14.3 U.S. gal
22 750 kPa
3300 psi
358 kg
784 lb
(Two Valves)
240 L/min
63 gpm
@ 2100 RPM (PMP)
72 L
19 U.S. gal
24 100 kPa
3500 psi
(Two Valves)
At Rear Center
of Fuel Tank
2 Std., 3 with Winch,
4 with Ripper, 5 with
Implement Towing AR
Electro/Hydraulic
Control System
270 L/min
71.3 gpm
@ 2200 RPM
75 L
19.8 U.S. gal
24 000 kPa
3481 psi
239 L/min
63 gpm
@ 1900 RPM
77.2 L
20.4 U.S. gal
26 200 kPa
3800 psi
(Two Valves)
D9T
D10T2
D11T
D11T CD
Under Operator’s
Platform
4
+ Dual Tilt (Attach.)
Electro/Hydraulic Control
System
Under Operator’s
Platform
5 Single Tilt
6 Dual Tilt
Under Operator’s
Platform
4
At Rear Under
Fuel Tank
1◀
+ Dual Tilt Standard
Radiator Guard
Under Operator’s
Platform
4
At Rear Under
Fuel Tank
1◀
Dual Tilt Standard
Quick Dump Valve
Standard
Both on Radiator Guard
670 L/min
177 gpm
@ 1800 RPM
223 L
58.9 U.S. gal
—
24 132 kPa
3500 psi
24 821 kPa
3600 psi
239 L/min
63 gpm
380 L/min
100.4 gpm
@ 1900 RPM
@ 1800 RPM
89 L
23.5 U.S. gal
131 L
34.6 U.S. gal
26 200 kPa
3800 psi
—
—
28 000 kPa
4061 psi
—
20 300 kPa
2944 psi
(Six Valves)
620 L/min
164 gpm
@ 1800 RPM
223 L
58.9 U.S. gal
—
22 753 kPa
3300 psi
24 304 kPa
3525 psi
◀ Ripper
valve.
NOTE: Weight installed, two valves, includes pump, tank with filters, valves, lines, linkage, oil cooler and control levers.
Edition 44
19-31
12/20/13 8:57 AM
Notes —
19-32
Edition 44
12/20/13 8:57 AM
19
BULLDOZERS
CONTENTS
Features:
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19-33
Summary of Blade Options. . . . . . . . . . . . . . . . . .19-34
Blade Selection . . . . . . . . . . . . . . . . . . . . . . . . . . .19-36
General Dimensions (Tractor and Blade) . . . . . . .19-39
SAE Blade Capacity Definition . . . . . . . . . . . . . .19-39
Blade Specifications. . . . . . . . . . . . . . . . . . . . . . . .19-40
Estimating Production Off-the-Job. . . . . . . . . . . .19-50
Job Condition Correction Factors . . . . . . . . . . . .19-55
Measuring Production On-the-Job . . . . . . . . . . . .19-56
Work Tools. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19-56
Special Attachments . . . . . . . . . . . . . . . . . . . . . . .19-57
●
Straight Bulldozers — adjustable tilt angle controls
blade penetration.
●
Variable cutting edge Power Angle and Tilt (VPAT)
— blade is available on the D3K, D4K, D5K, D6K/
D6K2, D6N, and D6T. The blade can be mechanically tipped forward for improved penetration or
back for more productivity and easier finish grading.
●
Angling Bulldozers — 25° right/left angling; C-frame
allows mounting other tools.
●
Universal Bulldozers — 25° wings provide increased
capacity, less spillage.
●
Semi-Universal Bulldozers — combines penetration
ability of straight blade with increased load capacity
provided by short 25° wings.
●
Wheel Dozer blades are offered in straight and universal blade design with hydraulic pitch and tilt control.
●
Box-section construction on blades adds rigidity and
strength.
●
Cutting edges are heat treated and reversible for extra
life.
Edition 44
PHB-Sec19-TTT-3-Bulldozers(pg33-58).indd 33
19-33
12/20/13 8:58 AM
Bulldozers
Summary
Blade Options for Caterpillar Built Machines
CAT BLADES
MODEL
D3K XL (LRC)
D3K LGP (LRC)
D3K2 XL
D3K2 LGP
D4K XL (LRC)
D4K LGP (LRC)
D4K2 XL
D4K2 LGP
D5K XL (LRC)
D5K LGP (LRC)
D5K2 XL
D5K2 LGP
D5E
D5R
D5R LGP
D6K XL
D6K LGP
D6K2 XL
D6K2 LGP
D6N XL
D6N LGP
D6N XL
Tier 4 Interim/
Stage IIIB
D6N LGP
Tier 4 Interim/
Stage IIIB
D6R
D6R XL
D6R LGP
D6R Series 3
D6R Series 3 XL
D6R Series 3 LGP
D6R Series 3 XW
D6T XL
D6T LGP
D6T XW
S
U
SU
A
SPECIAL BLADES
FS LFS VP
CD
RC WC
CL
HU
LF
TW CU CPB CB
VR WCB CS WCS W
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
CAT SUPPLIED
S — Straight
U — Universal
SU — Semi-Universal
A — Angling
FS — Fill Spreading
LFS — Landfill Spreading
VP — Variable Pitch, Lower, Angle and Tilt (VPAT)
SPECIAL SUPPLIED
RC — Reclamation U
WC — Woodchips
CL — Coal
HU — Heavy U
LF — Landfill
CD — CarryDozer
●
●
TW — Two-Way Dozer
CU — Cushion Dozer
CPB — Cushion Push Block
CB — Coal Bowldozer
VR — Variable Radius
WCB — Wood Chip Bowldozer
CS — Coal Scoop
WCS — Wood Chip Scoop
W — W-Blade
NOTE: This chart suggests a range of blade options for Caterpillar built machines. It is not totally inclusive of all blades available.
19-34
Edition 44
12/20/13 8:58 AM
Summary
Blade Options for Caterpillar Built Machines
CAT BLADES
MODEL
S
U
SU
A
D7E
D7E LGP
D7R
D7R XR
D7R LGP
D7R Series 2
D7R Series 2 LGP
D7G Series 2
D8R
D8R LGP
D8T
D8T LGP
D9R/D9T
D10T2
D11T
D11T CD
814F
815F
816F
824G/824H
825G
826G/826H
834G/834H
836G/836H
●
●
●
●
●
●
FS LFS VP
Bulldozers
19
SPECIAL BLADES
CD
RC WC
CL
HU
LF
TW CU CPB CB
VR WCB CS WCS W
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
CAT SUPPLIED
S — Straight
U — Universal
SU — Semi-Universal
A — Angling
FS — Fill Spreading
LFS — Landfill Spreading
VP — Variable Pitch, Lower, Angle and Tilt (VPAT)
●
●
●
●
SPECIAL SUPPLIED
RC — Reclamation U
WC — Woodchips
CL — Coal
HU — Heavy U
LF — Landfill
CD — CarryDozer
TW — Two-Way Dozer
CU — Cushion Dozer
CPB — Cushion Push Block
CB — Coal Bowldozer
VR — Variable Radius
●
●
WCB — Wood Chip Bowldozer
CS — Coal Scoop
WCS — Wood Chip Scoop
W — W-Blade
NOTE: This chart suggests a range of blade options for Caterpillar built machines. It is not totally inclusive of all blades available.
Edition 44
19-35
12/20/13 8:58 AM
Bulldozers
Blade Selection
● Production Dozing Toolsols
BLADE SELECTION
Tractor Limitations
Properly matching tractor and dozer is a basic requirement for maximizing production. First consider the
kind of work the tractor will be doing most of its life.
Then evaluate:
● Material to be moved.
● Tractor limitations.
The weight and horsepower of the machine determines its ability to push. No tractor can exert more
pounds push than the machine itself weighs and its
power train can develop. Various terrain and underfoot conditions on the job limit the tractor’s ability to
use its weight and horsepower. The “approximate coefficient of traction factors” chart in the Tables Section
presents these traction factors for common materials.
To use the chart, take the total tractor weight (with attachments) times the factor to arrive at the maximum usable
push the dozer can exert.
Materials to be moved
Most materials are dozeable. However, dozer performance will vary with material characteristics such as:
Particle Size and Shape — The larger the individual
particle size, the harder it is for a cutting edge to penetrate. Particles with sharp edges resist the natural rolling
action of a dozer blade. These particles require more
horsepower to move than a similar volume of material
with rounded edges.
Voids — Few voids or the absence of voids means the
individual particles have most or all of their surface
area in contact with other particles. This forms a bond
which must be broken. A well graded material, which
lacks voids, is generally heavy, and will be hard to
remove from the bank state.
Water Content — In most materials the lack of moisture increases the bond between particles and makes
the material difficult to remove from the bank state. A
high moisture content makes dozing difficult because
the material is heavy and requires more force to move.
Optimum moisture reduces dust and offers the best
condition for dozing ease and operator comfort.
The effect of freezing depends on the moisture content. When frozen, the material’s bond strengthens as
moisture content increases and temperature decreases.
However, freezing a completely dry material does not
change its characteristics.
An indication of a blade’s ability to penetrate and
obtain a blade load is kW per meter (or horsepower
per foot) of cutting edge. The higher the kW/meter
(HP/foot), the more aggressive the blade. Kilowatt per
Lm3 (horsepower per loose cubic yard) indicates a blade’s
ability to push material. The higher the kW/Lm3 (HP/
LCY), the greater the blade’s potential capability for
carrying material at a greater speed.
19-36
Production Dozing Tools
“U” — Universal blade —
the large wings on this blade
include one end bit and at
least one section of cutting
edge which make it efficient
for moving big loads over
long distances as in land reclamation, stockpile work,
charging hoppers and trapping for loaders. As this blade has a lower kW/meter
(HP/foot) of cutting edge than an “S” or “SU”, penetration should not be a prime objective. With a lower
kW/Lm3 (HP/LCY) than an “S” or “SU”, this blade is
best for lighter or relatively easily dozed material. If
equipped with tilt cylinders the U blade can be used to
pry out, level, cut ditches and steer the tractor.
“SU” — The Semi-U blade
combines the desir able
characteristics of S and
U-blades into one package. It has increased capacity by the addition of short
wings which include only
the dozer end bits. The
wings provide improved load retention capabilities
while maintaining the blade’s ability to penetrate and
load quickly in tightly packed materials and to handle
a wide variety of materials in production oriented
applications. Tilt cylinder(s) increase both the productivity and versatility of this dozer. Equipped with a push
plate, it is effectively used for push loading scrapers.
Edition 44
12/20/13 8:58 AM
Blade Selection
Production Dozing Tools
● General Purpose Dozing Tools
● Special Application Dozing Tools
Bulldozers
●
“CD” — The CD or CarryDozer Blade is available for
the D11T CarryDozer only.
It is built to the same high
standard of structural integrity as the “U” and “SU”
Dozers. The CD Blade has
a unique “bucket” shape that allows it to carry several
cubic yards or cubic meters of material in the blade.
This acts as a disposable counterweight that allows the
CarryDozer to push more material per pass than a
standard D11T. The CarryDozer will not be as effective
as the “U” or “SU” dozer in tightly packed or poorly
shot material. It is also more sensitive to the carryback in sticky materials.
General Purpose Dozing Tools
“S” — The Straight blade
provides excellent ver satility. Since it is physically
smaller than the SU or Ublade, it is easier to maneuver and can handle a wider
range of materials. It has a
higher kW/ meter (HP/foot)
of cutting edge than the SU or U-blade; consequently,
the “S” is more aggressive in penetrating and obtaining
a blade load. A tilt cylinder increases both the productivity and versatility of this dozer. With a high kW/Lm3
(HP/LCY), the S-blade can handle heavy material
easily.
Power Angle and Tilt
Blade — Versatility is its
key feature with its ability to perform a variety
of site development to
general dozing work as
well as heavy-duty applications. Angle and tilt control is with 2 levers on some
machines, 1 lever on others.
Variable Power Angle and Tilt (VPAT) blade can be
mechanically tipped forward for improved penetration
or shedding sticky material and backward for finish
grading and improved productivity.
19
Variable Radius (VR) Blades
Variable Radius Semi-U Blades
are excellent tools for land improvement, soil conservation,
site development or general
construction. They combine the
penetration ability of a Semi-U Blade with the load retention and high capacity of a U-blade.
They provide the aggressive cutting action needed
for digging, while having the material retention characteristics needed for moving high volumes over a distance.
This is accomplished through a moldboard which varies
in radius from the edge to the center. This creates a rolling action in the material being moved, pushing it to
the center of the blade for better retention. The extended
side wings, angled to thirty degrees, further increase the
capacity over a standard blade.
Angle Blade (A-Blade)
“A” — Or Angling blade
can be positioned straight or
angled 25 degrees to either
side. It is designed for sidecasting, pioneering roads,
backfilling, cutting ditches and other similar tasks. It
can reduce the amount of maneuvering required to do
these jobs. Its “C” frame can be used for attachments
such as pushing, land clearing, or snow removal tools.
A-blades are not recommended for rock or severe
applications.
Cushion Dozers
Cushion Dozers are
de signed to push-load
wheel-tractor scrapers, or
track-type tractors. The
heavy-duty design includes
reinforcement to transfer
machine power without
damaging the blade or the
tractor. Blade cylinders are pinned to the C-frame, and
the blade height is such that the blade lift cylinders are
isolated from damaging forces.
Special Application Dozing Tools
Caterpillar provides specialty bulldozers for specific
applications. The blades are designed to increase
production while performing certain tasks. Following
are the most popular special applications blades.
Edition 44
19-37
12/20/13 8:58 AM
Bulldozers
Blade Selection
● Special Application Dozing Tools
The taller blade allows pushing from a higher position, eliminating blade drag and increasing productivity. The blade curvature is matched to the curve of
the Cat Push Block for maximum contact area, preventing the block from riding over the top of the blade.
Extended side plates make it easier for operators to
“catch” the stinger when repositioning for a new pass.
The center of the blade is armored with T-1 plate steel
for maximum service life. The narrow width of the cushion blade increases machine maneuverability in congested cuts and reduces the possibility of cutting tires
associated with SU and U-blades.
When not push-loading, the dozer can be used for
cut maintenance and other general dozing jobs.
Coal U-Blades are designed
specifically to move large volumes of coal in coal piles,
at powerplants and transshipment points. The wing
angle of thirty degrees crowds
material to the center of the
blade, maximizing capacity by minimizing side spill.
The moldboard is much higher and wider than standard,
specifically to match the material density and loading
characteristics of coal. The curve of the moldboard rolls
the material forward, enhancing the carrying capacity.
With this design, coal-moving capacity can be as much
as 200 percent greater than a standard U-blade.
Landfill U-Blades provide
capacity increases of up to
fifty percent over a straight
blade. Land fill blades have
the height and width to handle large volumes of lowdensity refuse, but are tough
enough to dig and bulldoze ground cover. Vision to the
load is provided by areas of screen in the upper blade.
Angled wings slice into natural bed earth for trenches
or cover material, adding to the versatility in the landfill.
19-38
Reclamation U-Blades — are
purpose-built for recla mation of mine spoil piles. The
blade has a larger capacity
than a standard U-blade.
The wing angle of 28 degrees provides a good balance
between load retention and shearing action, keeping
the optimal load in front of the blade, but cutting
cleanly through the material when necessary.
The width of Woodchip UBlades gives operators maximum control and great er
confidence, even in steep chip
piles. Deep curvature of the
moldboard keeps material
flowing to liven dead chips
and optimize production on
long pushes. Blade height and wings angled at thirty
degrees combine for excellent material retention – giving better production with every pass. An operator visibility window in the top section is standard.
Multi-Application/Rock and Root Rakes
Multi-Application/Rock and
Root Rakes are perfectly
suited for heavy duty land
clearing including removal
of stumps, large rocks or
large trees and for work in
clay and other heavy soils.
Frames are constructed of high strength steel for longer
life. Cast teeth, with replaceable tips, are designed for
maximum ground penetration and resistance to shock
loading when prying or pushing trees, stumps and
rocks. Brush rack is standard and increases height and
capacity by as much as 40%.
Rake is a direct replacement for existing blade, and
utilizes existing push arms and C-frames.
Edition 44
12/20/13 8:58 AM
General Dimensions Key
● Tractor and Blade
● SAE Blade Capacity Definition
Bulldozers
19
KEY
A Length (Blade Straight)
Blade:
B Width (including standard end bits)
C Height
D Maximum Digging Depth
E Ground Clearance @ Full Lift
F Maximum Tilt (Manual)
G Maximum Pitch Adjustment
H Maximum Hydraulic Tilt
J Hydraulic Tilt (manual brace centered)
K Push Arm Trunnion Width (to Ball Centers)
Blade capacities on the following pages are as determined by SAE recommended practice J1265. Capacities are defined as:
Vs = 0.8 WH2.
Vu = ZH (W-Z) tan X.
Where: Vs = Capacity of straight or angling blade.
Vu = Capacity of semi-U or full U-blade.
W = Blade width exclusive of end bits.
H = Effective blade height considering
tapered top corners, etc.
Z = Wing length measured parallel to blade
width @ ground line of cutting edges.
X = Wing angle.
Edition 44
19-39
12/20/13 8:58 AM
Bulldozers
Blade Specifications
● D3K (LRC)
● D4K (LRC)
●
D5K (LRC)
D3K (LRC)
MODEL
Type
D4K (LRC)
XL
LGP
XL
LGP
Variable Power
Angling and Tilt
Variable Power
Angling and Tilt
Variable Power
Angling and Tilt
Variable Power
Angling and Tilt
Blade Capacities*
1.52 m3
1.99 yd3
1.66 m3
2.17 yd3
1.98 m3
2.59 yd3
1.85 m3
2.42 yd3
Weight Shipping** (Dozer)
572 kg
1261 lb
630 kg
1389 lb
642 kg
1415 lb
661 kg
1457 lb
Tractor and Dozer Dimensions:
4266 mm
168.0"
4255 mm
167.6"
4274 mm
168.3"
4266 mm
168.0"
Length (Blade Angled)
4763 mm
187.5"
4854 mm
191.1"
4795 mm
188.8"
4873 mm
191.8"
Width (Blade Angled)
2417 mm
95.1"
2874 mm
113"
2542 mm
100"
2874 mm
113"
124.0"
Blade Dimensions:
B Width (including std. end bits)
2646 mm
104.1"
3149 mm
124.0"
2782 mm
109.5"
3149 mm
C Height
910 mm
35.8"
860 mm
33.8"
1010 mm
39.8"
910 mm
35.8"
D Max. Digging Depth
573 mm
22.5"
573 mm
22.5"
572 mm
22.5"
590 mm
23.2"
730 mm
28.7"
730 mm
28.7"
743 mm
29.3"
708 mm
27.9"
G Max. Pitch Adjustment
J Hydraulic Tilt
Blade Angle
52° to 58°
368 mm
52° to 58°
14.4"
438 mm
25°
52° to 58°
17.2"
387 mm
25°
52° to 58°
15.2"
438 mm
25°
17.2"
25°
D5K (LRC)
MODEL
Type
XL
LGP
Variable Power
Angling and Tilt
Variable Power
Angling and Tilt
Blade Capacities*
2.19 m3
2.86 yd3
2.34 m3
3.06 yd3
706 kg
1556 lb
728 kg
1605 lb
4321 mm
170.1"
4294 mm
169.1"
4864 mm
191.5"
4908 mm
193.2"
2636 mm
103.8"
2940 mm
115.8"
2782 mm
109.5"
3220 mm
126.7"
C Height
1050 mm
41.3"
1010 mm
39.8"
586 mm
23.1"
572 mm
22.5"
767 mm
30.2"
767 mm
Blade Dimensions:
J Hydraulic Tilt
Blade Angle
52° to 58°
402 mm
15.8"
25°
30.2"
52° to 58°
448 mm
17.6"
25°
**Blade capacities as determined by SAE J1265.
**Shipping Weight — Total Bulldozer Arrangement includes: Blade, push arms or C-frame, braces, cylinders, lines, trunnions and lift cylinder mountings.
19-40
Edition 44
12/20/13 8:58 AM
D5R XL ● D5R LGP
● D6K LGP
● D6K2 XL
● D6K2 LGP
Bulldozers
●
●
MODEL
Type
D6K XL
ANGLE
D5R XL
SU
Angle Blade
Semi-Universal
19
VPAT XL
D5R LGP
VPAT LGP
Variable Pitch Power
Angle and Tilt
Angle and Tilt
Blade Capacities*
3.18 m3
4.16 yd3
4.28 m3
5.6 yd3
3.18 m3
4.16 yd3
3.16 m3
4.13 yd3
2546 kg
5612 lb
2600 kg
5732 lb
2375 kg
5236 lb
2740 kg
6041 lb
5157 mm
5035 mm
16'6.2"
5398 mm
17'8.5"
5680 mm
18'7.6"
6083 mm
19'11.5"
5193 mm
17.04'
6011 mm
19.72'
3785 mm
12.42'
—
2990 mm
9'9.7"
3727 mm
12'2.7"
Width (with C-Frame only)
2918 mm
9.57'
—
2500 mm
8'2.4"
3000 mm
9'10.1"
Blade Dimensions:
16'11"
—
(outside mounted)
(inside mounted)
(inside mounted)
4165 mm
13.66'
3154 mm
10'4.2"
3272 mm
10'8.8"
4082 mm
13'4.7"
C Height
1034 mm
3.39'
1244 mm
4'1"
1195 mm
3'11"
1040 mm
3'4.9"
534 mm
1.75'
520 mm
1'8.5"
420 mm
1'4.5"
500 mm
1'7.7"
1098 mm
3.60'
983 mm
3'2.7"
1067 mm
3'6"
1052 mm
3'5.4"
2'2.2"
485 mm
—
J Hydraulic Tilt
—
Blade Angle
MODEL
Type
±5°
665 mm
55.7° to 62.5°
1'7.1"
54° to 62°
585 mm
1'11"
25°
—
24.1°
24.1°
D6K XL
VPAT XL
D6K LGP
VPAT LGP
D6K2 XL
VPAT XL
D6K2 LGP
VPAT LGP
Tier 3/Stage IIIA
Tier 3/Stage IIIA
Tier 3/Stage IIIA
Tier 4 Interim/
Stage IIIB
Tier 3/Stage IIIA
Tier 4 Interim/
Stage IIIB
Angle and Tilt
Angle and Tilt
Angle and Tilt
Angle and Tilt
3.07 m3
3.35 m3
Blade Capacities*
2.97 m3
3.88 yd3
3.10 m3
4.05 yd3
2062 kg
4546 lb
2155 kg
4751 lb
4.01 yd3
4.38 yd3
—
—
A Length (Blade Straight)***
5020 mm
198"
5020 mm
198"
5008 mm
197"
5008 mm
197"
5620 mm
221"
5717 mm
225"
5369 mm
211"
5399 mm
212"
2922 mm
115"
3367 mm
133"
2878 mm
113.3"
3337 mm
131.4"
2330 mm
92"
2760 mm
109"
2330 mm
92"
2760 mm
109"
Blade Dimensions:
(inside mounted)
(inside mounted)
3195 mm
10'5.8"
3683 mm
12'1"
3196 mm
10'6"
3682 mm
12'0"
C Height
1140 mm
44.9"
1125 mm
44.3"
1294 mm
50.9"
1294 mm
50.9"
473 mm
18.6"
473 mm
18.6"
468 mm
18.4"
468 mm
18.4"
955 mm
3'1.6"
925 mm
3'0.4"
1203 mm
3'10.8"
1201 mm
3'11.3"
1'7.2"
525 mm
H Max. Hydraulic Tilt
Blade Angle
56° to 62°
486 mm
1'7.1"
24°
56° to 62°
552 mm
1'9.7"
24°
6°
488 mm
25°
6°
1'8.4"
25°
***Blade capacities as determined by SAE J1265.
Notice that the capacity of the SU-blade is the volume carried by a straight blade of the same dimensions plus the volume included in the “cup” of the
SU-blade. It is intended for relative comparisons of dozer sizes, and not for predicting capacities or productivities in actual field conditions.
***Shipping Weight — Total Bulldozer Arrangement includes: Blade, push arms or C-frame, braces, cylinders, lines, trunnions and lift cylinder mountings.
***With rear drawbar.
Edition 44
19-41
12/20/13 8:58 AM
Bulldozers
● D6N XL
● D6N LGP
D6R
D6N XL/
D6N XL Tier 4 Interim/
Stage IIIB
6SU
6VPAT XL
MODEL
Type
●
Semi-Universal
D6N LGP/
D6N LGP Tier 4 Interim/
Stage IIIB
6VPAT LGP
Angle and Tilt
Angle and Tilt
Blade Capacities*
4.28 m3
5.6 yd3
3.18 m3
4.16 yd3
3.16 m3
4.13 yd3
Weight, Shipping** (Dozer)
2600 kg
5732 lb
2375 kg
5236 lb
2740 kg
6041 lb
16'11"
5035 mm
16'6.2"
5398 mm
17'8.5"
5680 mm
18'7.6"
6083 mm
19'11.5"
5157 mm
—
—
2990 mm
9'9.7"
3727 mm
12'2.7"
—
2500 mm
8'2.4"
3000 mm
9'10.1"
Blade Dimensions:
(outside mounted)
(inside mounted)
(inside mounted)
3154 mm
10'4.2"
3272 mm
10'8.8"
4082 mm
13'4.7"
C Height
1244 mm
4'1"
1195 mm
3'11"
1040 mm
3'4.9"
520 mm
1'8.5"
420 mm
1'4.5"
500 mm
1'7.7"
983 mm
3'2.7"
1067 mm
3'6"
1052 mm
3'5.4"
2'2.2"
485 mm
Blade Angle
± 5°
665 mm
55.7° to 62.5°
—
54° to 62°
1'7.1"
585 mm
24.1°
1'11"
24.1°
D6R
MODEL
Gauge
6A
1.88 m
Type
6A XL
74"
1.88 m
Angling
74"
Angling
Blade Capacities*
3.94 m3
5.15 yd3
3.94 m3
5.15 yd3
3195 kg
7044 lb
3195 kg
7044 lb
5.00 m
17'1"
5.21 m
17'1"
5.83 m
19'2"
6.05 m
19'10"
3.77 m
12'5"
3.77 m
12'5"
2.99 m
9'10"
2.99 m
9'10"
Blade Dimensions:
4.16 m
13'8"
4.16 m
13'8"
C Height
1154 mm
3'10"
1154 mm
3'10"
511 mm
1'8"
511 mm
1'8"
1217 mm
4'0"
1217 mm
F Manual Tilt
—
485 mm
Blade Angle
K Push Arm Trunnion Width
(to Ball Centers)
1'4"
485 mm
25°
2.58 m
4'0"
—
1'4"
25°
8'6"
2.58 m
8'6"
*Blade capacities as determined by SAE J1265. Tractor and dozer dimensions variations due to SystemOne™ undercarriage products are negligible.
Notice that the capacity of the SU-blade is the volume carried by a straight blade of the same dimensions plus the volume included in the “cup” of the SU-blade.
It is intended for relative comparisons of dozer sizes, and not for predicting capacities or productivities in actual field conditions.
19-42
Edition 44
12/20/13 8:58 AM
● D6R
● D6T
Bulldozers
19
D6R
MODEL
6S
Gauge
—
Type
6SU
1880 mm
Straight
6SU XL
74"
1880 mm
Semi-Universal
74"
Semi-Universal
6S LGP
2.23 m
90"
Straight
Blade Capacities*
3.27 m3
4.27 yd3
5.35 m3
6.99 yd3
5.35 m3
6.99 yd3
5.50 m3
7.20 yd3
2599 kg
5717 lb
2973 kg
6540 lb
2973 kg
6540 lb
3054 kg
6733 lb
5.12 m
16'9"
5.08 m
16'8"
5.33 m
17'6"
5.48 m
18'0"
13'4"
Blade Dimensions:
3.36 m
11'0"
3.26 m
10'8"
3.26 m
10'8"
4.08 m
C Height
1257 mm
4'1.5"
1411 mm
4'8"
1411 mm
4'8"
1104 mm
3'7"
473 mm
18.6"
453 mm
1'6"
453 mm
1'6"
658 mm
2'2"
1104 mm
3'7.5"
1204 mm
3'11"
1204 mm
3'11"
1088 mm
F Manual Tilt
689 mm
2'3.1"
+5.3 to 4.8°
—
—
+5.6° to –5.2°
3'7"
—
+5.6° to –5.2°
+4.4° to –4.4°
764 mm
2'6.1"
811 mm
2'8"
811 mm
2'8"
747 mm
2'5"
J Hydraulic Tilt
(Manual Brace Centered)
420 mm
16.5"
455 mm
1'6"
455 mm
1'6"
421 mm
1'5"
2.58 m
8'6"
2.58 m
8'6"
3.42 m
11'5"
74"
1.88 m
(to Ball Centers)
—
MODEL
6A
D6T
Gauge
Type
6SU
1880 mm
74"
Angling
1880 mm
6A XL
74"
Semi-Universal
6SU XL
1.88 m
Angling
74"
Semi-Universal
Blade Capacities*
3.64 m3
4.75 yd3
5.35 m3
6.99 yd3
3.94 m3
5.15 yd3
5.35 m3
6.99 yd3
3138 kg
6904 lb
2973 kg
6540 lb
3195 kg
7044 lb
2973 kg
6540 lb
5.00 m
16'5"
5.08 m
5.33 m
5.83 m
19'2"
3.78 m
12'5"
2.93 m
9'8"
17'6"
5.21 m
17'1"
6.05 m
19'10"
—
3.77 m
12'5"
—
—
2.99 m
9'10"
—
—
17'6"
—
Blade Dimensions:
4.16 m
13'8"
3.26 m
10'8"
4.16 m
13'8"
3.26 m
C Height
1154 mm
3'10"
1411 mm
4'8"
1154 mm
3'10"
1411 mm
4'8"
506 mm
1'8"
453 mm
1'6"
511 mm
1'8"
453 mm
1'6"
1144 mm
3'9"
1204 mm
3'11"
1217 mm
4'0"
1204 mm
3'11"
—
519 mm
Blade Angle
1'8"
811 mm
25°
J Hydraulic Tilt
(to Ball Centers)
+5.6° to –5.2°
485 mm
—
—
2.58 m
2'8"
—
8'6"
+5.6° to –5.2°
1'4"
811 mm
25°
455 mm
1'6"
2.58 m
8'6"
2'8"
—
—
2.58 m
10'8"
8'6"
455 mm
1'6"
2.58 m
8'6"
*Blade capacities as determined by SAE J1265. Tractor and dozer dimensions variations due to SystemOne undercarriage products are negligible.
Edition 44
19-43
12/20/13 8:58 AM
Bulldozers
● D6T
D6T
MODEL
Gauge
Type
Blade Capacities*
Blade Dimensions:
C Height
Blade Angle
J Hydraulic Tilt
(to Ball Centers)
MODEL
Gauge
Type
Blade Capacities*
Blade Dimensions:
C Height
Blade Angle
J Hydraulic Tilt
(to Ball Centers)
6VPAT XL
2.13 m
6A XW
6SU XW
2.03 m
80"
Angling
4.27 m3
5.58 yd3
3430 kg
7562 lb
2.03 m
80"
Semi-Universal
5.50 m3
7.20 yd3
3128 kg
6896 lb
90"
VPAT
4.96 m3
6.48 yd3
3732 kg
8228 lb
5.29 m
6.20 m
4.11 m
3.29 m
17'4"
20'4"
13'6"
10'10"
5.33 m
5.53 m
6.40 m
3.72 m
4.52 m
1159 mm
495 mm
1243 mm
14'10"
3'10"
1'8"
4'1"
84"
VPAT
4.59 m3
6.00 yd3
3634 kg
8012 lb
5.39 m
3.54 m
3.49 m
17'8"
11'7"
11'5"
—
3.88 m
12'9"
1300 mm
4'3"
777 mm
2'6"
1136 mm
3'9"
+3.5° to –3.5°
614 mm
2'0"
24°
2.89 m
442 mm
1'5"
—
2.89 m
9'8"
—
9'8"
D6T
6S LGP
90"
2.23 m
Angling
4.16 m
13'8"
1300 mm
4'3"
727 mm
2'4"
1184 mm
3'11"
+3.5° to –3.5°
670 mm
2'2"
24°
6VPAT LGP
90"
2.23 m
Straight
4.89 m3
3799 kg
6.39 yd3
8375 lb
5.50 m3
3054 kg
5.81 m
6.81 m
4.63 m
3.77 m
19'1"
22'4"
15'2"
12'5"
5.50 m
5.07 m
1154 mm
830 mm
1093 mm
16'8"
3'9"
2'9"
3'7"
90"
VPAT
7.20 yd3
6733 lb
4.96 m3
3838 kg
18'1"
5.53 m
—
—
—
6.48 yd3
8461 lb
18'2"
—
3.72 m
12'2"
—
25°
4.08 m
13'4"
1104 mm
3'7"
658 mm
2'2"
1088 mm
3'7"
+4.4° to –4.4°
747 mm
2'5"
—
—
421 mm
1'5"
—
3.42 m
11'5"
—
—
585 mm
3.42 m
—
—
2'0"
6A LGP
2.23 m
1'11"
11'5"
18'2"
21'0"
12'2"
25°
—
—
17'6"
—
—
—
3.56 m
11'8"
1411 mm
4'8"
463 mm
1'6"
1204 mm
3'11"
+4.0° to –4.0°
791 mm
2'7"
—
603 mm
—
6VPAT XW
2.29 m
4.16 m
13'8"
1300 mm
4'3"
715 mm
2'4"
1185 mm
3'11"
+3.5° to –3.5°
435 mm
1'5"
24°
*Blade capacities as determined by SAE J1265.
19-44
Edition 44
12/20/13 8:58 AM
● D7E
● D7R
● D7R XR
● D7R LGP
Bulldozers
19
D7E
MODEL
Type
Blade Capacities*
Blade Dimensions:
C Height
Blade Angle (either side)
J Hydraulic Tilt
(to Ball Centers)
7A
7S
7SU
7U
Angling
6.75 yd3
5.15 m3
3489 kg
7692 lb
Straight
5.16 m3
6.75 yd3
3577 kg
7886 lb
Semi-Universal
6.86 m3
8.98 yd3
3632 kg
8007 lb
Universal
8.34 m3
10.91 yd3
3874 kg
8541 lb
6.20 m
7.07 m
4.12 m
3.40 m
20'4"
23'2"
13'6"
11'2"
5.92 m
6.17 m
6.38 m
4.50 m
1373 mm
797 mm
1100 mm
14'9"
4'6
2'7"
3'7"
—
25°
685 mm
2'3"
4.02 m
13'2"
1553 mm
5'1"
568 mm
1'10"
1144 mm
3'9"
52° to 58°
—
821 mm
2'8"
530 mm
1'9"
500 mm
1'8"
550 mm
1'10"
2.81 m
9'2"
2.81 m
9'2"
2.81 m
9'2"
D7E
7S LGP
Type
20'11"
—
—
—
3.71 m
12'2"
1524 mm
5'0"
568 mm
1'10"
1144 mm
3'9"
52° to 58°
—
760 mm
2'6"
9'2"
MODEL
20'3"
—
—
—
3.90 m
12'10"
1520 mm
5'0"
568 mm
1'10"
1144 mm
3'9"
52° to 58°
—
813 mm
2'8"
—
2.81 m
19'5"
—
—
—
D7R/D7R XR
7SU
Straight
D7R LGP
7S
Semi-Universal
Straight
Blade Capacities*
5.89 m3
7.70 yd3
6.86 m3
8.98 yd3
5.89 m3
7.7 yd3
3764 kg
8298 lb
3593 kg
7904 lb
3732 kg
8229 lb
6.28 m
20'7"
6.03 m
19'9"
5.81 m
19'1"
4.58 m
15'0"
3.69 m
12'1"
4.50 m
14'9"
1348 mm
4'5"
1524 mm
5'0"
1343 mm
4'4.9"
Blade Dimensions:
C Height
640 mm
2'1"
527 mm
1'8.7"
668 mm
2'2.3"
1285 mm
4'3"
1145 mm
3'9.1"
1153 mm
3'9.4"
J Hydraulic Tilt
(to Ball Centers)
54° to 60°
+3.1° to 3.9°
+ 3.0° to 3.9°
778 mm
2'7"
470 mm
1'7"
799 mm
2'7.4"
686 mm
2'3"
3.35 m
11'0"
474 mm
18.6"
426 mm
16.8"
2.87 m
9'5"
3.37 m
11'1"
—
—
—
Notice that the capacity of the U-blade is the volume carried by a straight blade of the same dimensions plus the volume included in the “cup” of the U-blade.
Edition 44
19-45
12/20/13 8:58 AM
Bulldozers
● D8R
● D8T
D8R/D8T
MODEL
Type
8A
8SU
8U
Angling
Semi-U
Universal
8SU LGP
Semi-U
Blade Capacities*
4.7 m3
6.1 yd3
8.7 m3
11.4 yd3
11.7 m3
15.3 yd3
8.5 m3
11.1 yd3
5503 kg
12,132 lb
4706 kg
10,375 lb
5336 kg
11,764 lb
5146 kg
11,345 lb
6.39 m
21'0"
6.79 m
22'3"
6281 mm
6.57 m
21'7"
7.62 m
25'0"
—
—
—
20'7"
4.52 m
14'10"
—
—
—
3.38 m
11'1"
—
—
—
Blade Dimensions:
5.00 m
16'5"
3.93 m
12'11"
4.25 m
13'11"
4.53 m
C Height
1174 mm
3'10"
1690 mm
5'7"
1740 mm
5'9"
1622 mm
5'4"
628 mm
2'1"
574 mm
22.6"
575 mm
22.6"
577 mm
22.7"
1308 mm
4'3"
1225 mm
4'0"
1225 mm
4'0"
1222 mm
—
25°
729 mm
J Hydraulic Tilt
(to Ball Centers)
Maximum Track Width Permitted
+3.0° to 2.9°
+3.0° to 2.9°
—
2'5"
—
14'10"
4'0"
—
—
—
883 mm
2'11"
954 mm
3'2"
585 mm
1'11"
635 mm
2'1"
914 mm
3'0"
—
2983 mm
9'9"
2983 mm
9'9"
2983 mm
9'9"
3329 mm
10'11"
710 mm
2'4"
710 mm
2'4"
710 mm
2'4"
965 mm
3'2"
2'11"
950 mm
Dual Tilt Option
G Dual Pitch Adj.
—
H Dual Max. Hyd. Tilt
—
±4.6°
879 mm
±4.6°
—
3'1"
—
19-46
Edition 44
12/20/13 8:58 AM
● D9R
● D9T
Bulldozers
19
D9R/D9T
MODEL
Type
9SU
9U
Semi-U
Universal
Blade Capacities*
13.5 m3
17.7 yd3
16.4 m3
21.4 yd3
6543 kg
14,425 lb
7134 kg
15,727 lb
6.84 m
22'5"
7.18 m
23'7"
Blade Dimensions:
4.35 m
14'3"
4.68 m
15'4"
1934 mm
6'4.1"
1934 mm
6'4.1"
606 mm
1'11.9"
606 mm
1'11.9"
1422 mm
4'8"
1422 mm
C Height
+3.4° to 2.9°
4'8"
+3.4° to 2.9°
940 mm
3'1"
1014 mm
3'3.9"
J Hydraulic Tilt
570 mm
1'10.4"
616 mm
2'0.3"
3.17 m
10'3"
3.17 m
10'3"
762 mm
2'6"
762 mm
2'6"
3'8.8"
1231 mm
(to Ball Centers)
Dual Tilt Option
G Dual Pitch Adj.
+4.8° to 5.2°
1139 mm
+4.8° to 4.9°
4'0.5"
Edition 44
19-47
12/20/13 8:58 AM
Bulldozers
● D10T2
D10T2
MODEL
10SU
10U
Type
Semi-U
Universal
18.5 m3
24.2 yd3
Standard Dozer
10 229 kg
Abrasion Dozer
11 069 kg
Blade Capacities*
22.0 m3
28.7 yd3
22,550 lb
10 784 kg
23,775 lb
24,403 lb
12 413 kg
27,366 lb
Weight, Shipping**
A Length
7.50 m
24'7"
7.75 m
25'5"
4.86 m
15'11"
5.26 m
17'3"
4.94 m
16'3"
5.26 m
17'3"
C Height
2.12 m
6'11"
2.12 m
6'11"
674 mm
2'2.5"
674 mm
2'2.5"
1497 mm
4'10.9"
1497 mm
Width
Blade Dimensions:
+1.7° to 2.3°
4'10.9"
+1.7° to 2.3°
993 mm
3'3.1"
1074 mm
3'6.3"
J Hydraulic Tilt
722 mm
2'4.4"
782 mm
2'6.8"
3.60 m
11'10"
3.60 m
11'10"
762 mm
2'6"
762 mm
2'6"
4'8.7"
1560 mm
(to Ball Centers)
Dual Tilt Option
G Dual Pitch Adjustment
+5.2° to 5.5°
1441 mm
+5.2° to 5.5°
5'1.4"
**Blade capacities as determined by SAE J1265.
**Notice that the capacity of the U-blade is the volume carried by a straight blade of the same dimensions plus the volume included in the “cup” of the U-blade.
19-48
Edition 44
12/20/13 8:58 AM
● D11T
Bulldozers
19
MODEL
11SU
D11T
11U
11 CD
Type
Semi-U
Universal
CarryDozer
27.2 m3
35.5 yd3
34.4 m3
45.0 yd3
43.6 m3
Standard Dozer
14 813 kg
32,658 lb
17 296 kg
38,131 lb
24 085 kg
Abrasion Dozer
16 192 kg
35,698 lb
18 823 kg
41,498 lb
Blade Capacities*
57.0 yd3
Weight, Shipping**
53,099 lb
—
A Length
8.38 m
27'6"
8.83 m
28'11"
8.34 m
26'8"
5.60 m
18'4"
6.35 m
20'10"
6.71 m
22'0"
5.58 m
18'4"
6.35 m
20'10"
6.71 m
22'0"
C Height
2.77 m
9'1''
2.77 m
9'1''
2.74 m***
9'0''***
2'3"
Width
Blade Dimensions:
766 mm
2'6.2"
766 mm
2'6.2"
688 mm
1533 mm
5'0.4"
1533 mm
5'0.4"
1850 mm
+2.1° to 2.2°
+2.1° to 2.2°
6'1"
—
1184 mm
3'10.6"
1344 mm
4'4.9"
J Hydraulic Tilt
886 mm
2'10.9"
1006 mm
3'3.6"
4.18 m
13'9"
4.18 m
13'9"
4.18 m
13'9"
914 mm
3'0"
914 mm
3'0"
914 mm
3'0"
(to Ball Centers)
Dual Tilt Option
G Dual Pitch Adjustment
+7.5° to 7.6°
or
or
+0° to 13°
5'7.2"
5'11''
—
+7.5° to 7.6°
+0° to 13°
1706 mm
1800 mm
1938 mm
+47.8° to 10.4°
6'4.3"
—
***Blade capacities as determined by SAE J1265.
***Notice that the capacity of the U-blade is the volume carried by a straight blade of the same dimensions plus the volume included in the “cup” of the U-blade.
***Shipping Weight — Total Bulldozer Arrangement includes: Blade, push arms or C-frame, braces, cylinders, lines, trunnions and lift cylinder mountings.
***Blade height with cutting edge at 53°.
Edition 44
19-49
12/20/13 8:58 AM
Bulldozers
Estimating Production Off-the-Job
BULLDOZER PRODUCTION OFF-THE-JOB
You can estimate bulldozer production using the production curves that follow and the correction factors
that are applicable. Use this formula:
Correction
Maximum
Production (Lm3/hr)
×
=
factors
(LCY/hr) production
The bulldozer production curves give maximum uncorrected production for universal, semi-universal, and
straight blades and are based on the following conditions:
1. 100% efficiency (60 minute hour — level cycle).
2. Power shift machines with 0.05 min. fixed times.
3. Machine cuts for 15 m (50 feet), then drifts blade
load to dump over a high wall. (Dump time — 0 sec.)
4. Soil density of 1370 kg/Lm3 (2300 lb/LCY).
5. Coefficient of traction:*
a. Track machines — 0.5 or better
b. Wheel machines — 0.4 or better
6. Hydraulic controlled blades used.
7. Dig 1F**
Carry 2F**
Return 2R**
To obtain estimated production in bank cubic meters
or bank cubic yards, appropriate load factor from the
Tables section should be applied to the corrected production as calculated above.
*Coefficient of traction assumed to be at least 0.4. While poor
traction affects both track and wheel vehicles, causing them to
take smaller blade loads, wheeled units are affected more
severely and production falls much more rapidly. While no
fixed rules can predict this production loss, a rough rule of
thumb is that wheel dozer production falls off 4% for each
one-hundredth decrease in coefficient of traction below 0.40.
If, for example, coefficient of traction is 0.30, the difference is
ten-hundredths (0.10), and production is 60% (10 × 4% =
40% decrease).
**This gear sequence is based on level to downhill terrain,
light to medium density material, and no blade extensions
such as spill plates, rock guards, etc. Exceeding these conditions may require carry in 1F, but productivity should equal
or exceed “standard conditions” due to the larger loads that
can be carried in 1F.
Production Bm3/hr
Lm3/hr × LF
(BCY/h) = (LCY/h) × LF
19-50
Edition 44
12/20/13 8:58 AM
● U-Blades
Bulldozers
19
ESTIMATED DOZING PRODUCTION ● Universal Blades ● D7E through D11T CD
Lm3/hr
3900
3600
EST. DOZING PRODUCTION
3300
3000
2700
2400
2100
1800
1500
1200
900
600
300
0
LCY/hr
5200
5000
4800
4600
4400
4200
4000
3800
3600
3400
3200
3000
2800
2600
2400
2200
2000
1800
1600
1400
1200
1000
800
600
400
200
0
A
B
C
D
E
F
0
100
200
300
0
30
60
90
400
120
500
150
600 Feet
180
Meters
AVERAGE DOZING DISTANCE
KEY
A — D11T CD
B — D11T
C — D10T2
D — D9T
E — D8T
F — D7E
NOTE: This chart is based on numerous
field studies made under varying
job conditions. Refer to correction
factors following these charts.
Edition 44
19-51
12/20/13 8:58 AM
Bulldozers
● SU-Blades
ESTIMATED DOZING PRODUCTION ● Semi-Universal Blades ● D7E through D11T
Lm3/hr
LCY/hr
3800
2700
2400
A
3600
3400
3200
3000
2100
2800
2600
1800
B
2400
2200
1500
2000
1800
1200
C
1600
1400
900
1200
D
E
1000
600
800
600
300
400
200
0
0
0
100
200
300
400
500
0
30
60
90
120
150
600 Feet
180
Meters
KEY
A — D11T
B — D10T2
C — D9T
D — D8T
E — D7E
19-52
Edition 44
12/20/13 8:58 AM
● SU-Blades
Bulldozers
19
ESTIMATED DOZING PRODUCTION ● Semi-Universal Blades ● D6N through D8R
Lm3/hr
900
LCY/hr
1200
1100
A
1000
900
B
600
800
C
D
E
700
600
F
500
300
400
300
200
100
0
0
0
100
200
300
400
0
30
60
90
120
500
150
600 Feet
180
Meters
KEY
A — D8R
B — D7R
C — D6T Tier 4 Interim/Stage IIIB
D — D6T
E — D6R
F — D6N
Edition 44
19-53
12/20/13 8:58 AM
Bulldozers
● S-Blades
ESTIMATED DOZING PRODUCTION ● Straight Blades ● D6T through D7E
Lm3/hr
600
LCY/hr
800
A
700
500
600
B
400
500
400
300
300
200
200
100
100
0
0
0
0
50
10
100
20
30
150
40
50
200
60
250
70
80
350 Feet
300
90
100
Meters
KEY
A — D7E
B — D6T
19-54
Edition 44
12/20/13 8:58 AM
Job Factors
● Example Problem
JOB CONDITION CORRECTION FACTORS
(–) Downhill
(+) Uphill
1.8
Excellent
1.00
Average
0.75
1.6
Poor
0.60
1.4
MATERIAL —
Loose stockpile
1.20
Hard to cut; frozen —
0.80
without tilt cylinder
0.70
Rock, ripped or blasted
SLOT DOZING
SIDE BY SIDE DOZING
0.80
.8
.6
.4
0.60-0.80
1.20
.2
–30
–20
–10
0
+10
+20
0.80
JOB EFFICIENCY —
50 min/hr
0.83
40 min/hr
0.67
BULLDOZER*
Adjust based on SAE capacity
relative to the base blade used in
the Estimated Dozing Production
graphs.
GRADES — See following graph.
*NOTE: Angling blades and cushion blades are not considered production
dozing tools. Depending on job conditions, the A-blade and
C-blade will average 50-75% of straight blade production.
ESTIMATING DOZER PRODUCTION
OFF-THE-JOB
Example problem:
Determine average hourly production of a D8T/8SU
(with tilt cylinder) moving hard-packed clay an average
distance of 45 m (150 feet) down a 15% grade, using a
slot dozing technique.
Estimated material weight is 1600 kg/Lm3 (2650 lb/
LCY). Operator is average. Job efficiency is estimated
at 50 min/hr.
Uncorrected Maximum Production — 458 Lm 3/h
(600 LCY/hr) (example only)
Applicable Correction Factors:
Hard-packed clay is “hard to cut” material . . .–0.80
Grade correction (from graph) . . . . . . . . . . . . .–1.30
Slot dozing . . . . . . . . . . . . . . . . . . . . . . . . . . . . .–1.20
Average operator . . . . . . . . . . . . . . . . . . . . . . . .–0.75
Job efficiency (50 min/hr) . . . . . . . . . . . . . . . . .–0.83
Weight correction. . . . . . . . . . . . . . (2300/2650)–0.87
Production = Maximum Production × Correction
Factors
= (600 LCY/hr) (0.80) (1.30) (1.20) (0.75)
(0.83) (0.87)
= 405.5 LCY/hr
To obtain production in metric units, the same procedure is used substituting maximum uncorrected production in Lm3.
= 458 Lm3/h × Factors
= 309.6 Lm3/h
Edition 44
+30
1.15-1.25
VISIBILITY —
Dust, rain, snow, fog or darkness
1.2
1.0
with tilt cylinder
Hard to drift; “dead” (dry, noncohesive material) or very sticky
material
19
% Grade vs. Dozing Factor
TRACK-TYPE
TRACTOR
OPERATOR —
Bulldozers
19-55
12/20/13 8:58 AM
Bulldozers
Measuring Production
On-the-Job
● Work Tools
MEASURING PRODUCTION ON-THE-JOB
Three generally accepted methods of measuring bulldozer production are listed below. The third method is
empirical, but is the simplest to conduct.
1. Employing Surveying Techniques
a. Conduct time study and then cross-section the
cut to determine the volume of material removed.
(Production in Bm3 or BCY per unit of time)
b. Conduct time study and then cross-section the fill
to determine the volume of fill material. (Production in Lm3 or LCY per unit of time)
2. Weighing Blade Loads
Conduct time study and weigh material moved
by bulldozer by weighing the loader bucket loads.
3. Measuring Blade Loads
a. Dozer operation
(1) Pick up and carry load onto a level area and
stop.
(2) Raise the blade directly over the pile pulling
forward slightly as blade comes up, leaving a
nearly symmetrical pile.
(3) Reverse to clear the pile.
b. Measurements
(1) The average height (H) of the pile in feet. Hold
the tape vertically at the inside edge of each
grouser mark. Sight along top of the pile to
obtain the correct measurement.
SIDE VIEW
TOP VIEW
GROUSER MARKS
(2) The average width (W) of the pile in feet. Hold the
tape horizontally over the pile and sight at the inside
edge of each grouser mark and the corresponding
opposite side of the pile.
(3) The greatest length (L) of the pile in feet.
Hold the tape horizontally over the pile and
sight at each end of the pile.
c. With the above measurements, now compute the
blade load.
(1) Average the height measurement (H)
(2) Average the width measurement (W)
(3) Load (Lm3 or LCY) = 0.0138 × (HWL)
(4) Load (Bm3 or BCY) = Lm3 or LCY × LF
d. Combine the calculated blade load with time
study to figure production.
WORK TOOLS
VARIABLE RADIUS (VR)
SEMI-U BLADES
Capacity
Width
Height
Weight
D6T
5.81 m3
3349 mm
1473 mm
1360 kg
LANDFILL BLADES
Capacity
Width
Height
Weight
LANDFILL BLADES
Capacity
Width
Height
Weight
D7R
7.6 yd3
11'0"
4'10"
3000 lb
7.84 m3
3912 mm
1626 mm
2000 kg
16.4 yd3
12'9"
5'10.7"
3200 lb
14 m3
3713 mm
1524 mm
4380 kg
D6T
12.5 m3
3886 mm
1796 mm
1450 kg
11.28 m3
4369 mm
1778 mm
3010 kg
18.4 yd3
12'2"
5'0"
9636 lb
18.1 m3
4267 mm
2083 mm
2608 kg
D7E
D8R/D8T
24.4 m3
4928 mm
2286 mm
3175 kg
D8R/D8T
10.25 yd3
12'10"
5'4"
4400 lb
32 yd3
16'2"
7'6"
7000 lb
14.75 yd3
14'4"
5'10"
6640 lb
D7R
23.7 yd3
14'0"
6'10"
5750 lb
D9R/D9T
38.5 m3
5442 mm
2178 mm
4900 kg
50.3 yd3
17'10"
7'1.75"
10,800 lb
This list is not all inclusive. Contact your Cat dealer for special attachment needs.
19-56
Edition 44
12/20/13 8:58 AM
Special Attachments
Coal U-Blades ● Woodchip Dozers
● Reclamation U-Blades
● Cushion Dozers
Bulldozers
●
COAL U-BLADES
Capacity
Width
Height
Weight
COAL U-BLADES
Capacity
Width
Height
Weight
D6T
9.7 m3
4267 mm
1473 mm
1452 kg
D8R/D8T
21.4 m3
5537 mm
1930 mm
3200 kg
WOODCHIP DOZERS
Capacity
Width
Height
Weight
RECLAMATION U-BLADES
Capacity
Width
Height
Weight
CUSHION
DOZERS
Width
Height
Weight
Rear Cushion
Push Block
14.8 m2
4902 mm
1778 mm
2420 kg
37 m3
5940 mm
2540 mm
4490 kg
23.5 m2
4902 mm
2286 mm
2731 kg
D8R/D8T
45.9 m3
5486 mm
3086 mm
5080 kg
D8R/D8T
D8R/D8T
2889 mm
1499 mm
3185 kg
9'5.75"
4'11"
7020 lb
*
20.9 m3
5182 mm
2032 mm
5220 kg
D9R/D9T
74.9 m3
7416 mm
3330 mm
11 340 kg
98.0 yd3
24'4"
10'11"
25,000 lb
D7E LGP
30.8 yd2
193"
90"
6020 lb
23.5 m2
4902 mm
2286 mm
2896 kg
30.8 yd2
193"
90"
6384 lb
D10T2
60 yd3
18'0"
10'1.5"
11,200 lb
72.6 m3
6300 mm
3480 mm
7575 kg
D9R/D9T
21.5 yd3
16'0"
6'2"
8400 lb
19.4 yd2
193"
70"
5714 lb
D11T
60.3 yd3
20'1"
9'2"
14,700 lb
D9R/D9T
37 yd3
18'0"
7'8"
6400 lb
16.4 m3
4877 mm
1880 mm
3810 kg
46.1 m3
6191 mm
2794 mm
6670 kg
D7E
20 yd3
14'0"
6'2"
3800 lb
28.3 m3
5486 mm
2337 mm
2903 kg
14.8 m2
4902 mm
1778 mm
2592 kg
D10T2
48 yd3
18'10"
8'4"
9900 lb
D6T
15 m3
4267 mm
1880 mm
1724 kg
D7E LGP
19.4 yd2
193"
70"
5335 lb
D9R/D9T
28 yd3
18'2"
6'4"
7050 lb
WOODCHIP DOZERS
Capacity
Width
Height
Weight
D7E
12.63 yd3
14'0"
4'10"
3200 lb
19
95 yd3
20'8"
11'5"
16,700 lb
D10T2
27.3 yd3
17'0"
6'8"
11,500 lb
30.6 m3
5664 mm
2388 mm
6440 kg
D10T2
40 yd3
18'7"
7'10"
14,200 lb
D11T
3048 mm
1575 mm
4310 kg
10'0"
5'2"
9500 lb
3505 mm
1676 mm
6440 kg
11'6"
5'6"
14,200 lb
*
2175 kg
4800 lb
3105 kg
6850 lb
*
*Available upon request.
This list is not all inclusive.
Edition 44
19-57
12/20/13 8:58 AM
Notes —
19-58
Edition 44
12/20/13 8:58 AM
19
RIPPERS
CONTENTS
Features:
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19-59
Ripper Specification Diagrams
Adjustable Parallelogram Ripper . . . . . . . . . . .19-60
Radial Ripper . . . . . . . . . . . . . . . . . . . . . . . . . .19-62
Fixed Parallelogram Ripper . . . . . . . . . . . . . . .19-62
Specifications
Track-Type Tractors . . . . . . . . . . . . . . . . . . . . .19-63
Tip Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19-73
Estimating Ripping Production . . . . . . . . . . . . . .19-73
Seismic Wave Velocity Charts . . . . . . . . . . . . . . . .19-76
Estimated Ripper Production Graphs . . . . . . . . .19-81
●
Parallelogram linkage with hydraulically variable
pitch on D7E, D7R, D8R/D8T, D9R/D9T, D10T2
and D11T. Operator can adjust angle of ripper tip to
the material for penetration at all ripping depths to
increase production.
●
Fixed Parallelogram linkage design used on D3K,
D4K, D5K, D6K/D6K2, D6N, D6R, D6R XL,
D6T and D6T XL. This design holds tooth angle
constant at all ripping depths.
●
Adjustable Single shank arrangements available for
D8R/D8T, D9R/D9T, D10T2 and D11T for tough
ripping applications and deep ripping requirements.
●
Hydraulically Variable Pitch Multi-shank arrangements
available on D7E, D7R, D8R/D8T, D9R/D9T, D10T2
and D11T allow wide-beam coverage in easier-to-rip
materials.
●
Counterweighted CarryDozer Ripper single shank
available for D11T and D11T CD, multi-shank available for D11T CD.
Edition 44
PHB-Sec19-TTT-4-Rippers(pg59-82).indd 59
19-59
12/20/13 8:58 AM
Rippers
Specification Diagrams
● Adjustable Parallelogram Ripper
DEFINITION OF FORCES SHOWN IN TABLES THAT FOLLOW
“Pryout,” (Breakout) kilonewtons (and pounds) — the
maximum sustained upward force, generated by the lift
cylinders measured at the ripper tip. Breakout force is
measured with the shank in the top hole, shank vertical
and ripper full down. Breakout force may be hydraulically or balance limited.
“Penetration force,” kilonewtons (and pounds) — the
maximum sustained downward force, generated by the
ripper lift cylinders measured at the ripper tip, which is
required to raise the back end of the vehicle with the tip
on ground and the shank (pinned in the top hole) vertical.
Adjustable Parallelogram Ripper
NOTE: Letters correspond to ripper specifications on pages that follow.
KEY
AA — Ground Line
19-60
Edition 44
12/20/13 8:58 AM
●
Rippers
19
KEY
AA — Ground Line
BB — Track Gauge
Edition 44
19-61
12/20/13 8:58 AM
Rippers
● Radial Ripper
● Fixed Parallelogram Ripper
Radial Ripper*
Fixed Parallelogram Ripper
KEY
AA — Ground Line
* — Tip Standard
19-62
Edition 44
12/20/13 8:58 AM
●
TRACTOR/RIPPER
Ripper Type
Dimensions:
Ripper Shank
G Maximum digging depth
L Maximum reach at ground line
M Maximum ground clearance under tip
(shank pinned in bottom hole)
N Maximum ramp angle, ripper up
Shank section
Ripper Beam
O Overall width
P Height
Q Length
Number of Pockets
T Pocket Spacing
U Shank Gauge
V Track clearance with standard shoe
Installed weights:
Ripper with standard shank
Ripper Forces:*
Penetration Force
Pryout Force
Specifications
D3K2 ● D4K (LRC)
● D5K (LRC)
● D5K2
Rippers
●
19
D3K (LRC)
D3K2
D4K (LRC)
Fixed Parallelogram
Fixed Parallelogram
Fixed Parallelogram
338 mm
766 mm
13.3"
30.2"
338 mm
766 mm
13.3"
30.2"
338 mm
596 mm
13.3"
23.5"
448 mm
17.6"
448 mm
17.6"
448 mm
17.6"
27°
36 × 76 mm
1.4" × 3"
1710 mm
165 mm
190 mm
27°
36 × 76 mm
1.4" × 3"
67.3"
6.5"
7.5"
1710 mm
165 mm
190 mm
775 mm
1550 mm
80 mm
30.5"
61.0"
3.2"
554 kg
22.1 kN
44.0 kN
32°
36 × 76 mm
1.4" × 3"
67.3"
6.5"
7.5"
1710 mm
165 mm
190 mm
775 mm
1.55 m
80 mm
30.5"
61.0"
3.2"
775 mm
1550 mm
80 mm
30.5"
61.0"
3.2"
1222 lb
554 kg
1222 lb
554 kg
1222 lb
4970 lb
9900 lb
22.1 kN
44.0 kN
4970 lb
9900 lb
24.7 kN
44.0 kN
5560 lb
9900 lb
3
TRACTOR/RIPPER
Ripper Type
Dimensions:
Ripper Shank
Shank section
Ripper Beam
O Overall width
P Height
Q Length
Number of Pockets
T Pocket Spacing
U Shank Gauge
Installed weights:
Ripper Forces:*
Penetration Force
Pryout Force
D3K (LRC)
● D4K2
3
67.3"
6.5"
7.5"
3
D4K2
D5K (LRC)
D5K2
Fixed Parallelogram
Fixed Parallelogram
Fixed Parallelogram
338 mm
766 mm
13.3"
30.2"
338 mm
555 mm
13.3"
21.9"
338 mm
766 mm
13.3"
30.2"
448 mm
17.6"
448 mm
17.6"
448 mm
17.6"
27°
36 × 76 mm
1.4" × 3"
1710 mm
165 mm
190 mm
33°
36 × 76 mm
1.4" × 3"
67.3"
6.5"
7.5"
1710 mm
165 mm
190 mm
775 mm
1.55 m
80 mm
30.5"
61.0"
3.2"
554 kg
22.1 kN
44.0 kN
27°
36 × 76 mm
1.4" × 3"
67.3"
6.5"
7.5"
1710 mm
165 mm
190 mm
775 mm
1550 mm
80 mm
30.5"
61.0"
3.2"
775 mm
1.55 m
80 mm
30.5"
61.0"
3.2"
1222 lb
554 kg
1222 lb
554 kg
1222 lb
4970 lb
9900 lb
27.3 kN
44.0 kN
6130 lb
9900 lb
22.1 kN
44.0 kN
4970 lb
9900 lb
3
3
67.3"
6.5"
7.5"
3
*This value may vary slightly with various vehicle configurations.
NOTE: Letters correspond to ripper dimension drawings.
Edition 44
19-63
12/20/13 8:58 AM
Rippers
Specifications
● D5R XL
● D6K XL
● D6K LGP
● D6K2 XL
● D6K2 LGP
● D6N XL
TRACTOR/RIPPER
Ripper Type
Dimensions:
Ripper Shank
Ripper Beam
O Overall width
P Height
Q Length
Number of Pockets
T Pocket Spacing
U Shank Gauge
Installed weights:
Each additional shank
Ripper Forces:
Penetration Force
Pryout Force
TRACTOR/RIPPER
Ripper Type
Dimensions:
Ripper Shank
Ripper Beam
O Overall width
P Height
Q Length
Number of Pockets
T Pocket Spacing
U Shank Gauge
Installed weights:
Ripper Forces:
Penetration Force
Pryout Force
D5R XL
D6K XL
D6K LGP
Parallelogram
Fixed Parallelogram
Fixed Parallelogram
355 mm
516 mm
14.0"
1'8.3"
355 mm
725 mm
14.0"
28.5"
355 mm
725 mm
14.0"
28.5"
422 mm
16.6"
471 mm
18.5"
471 mm
18.5"
21.4°
2200 mm
216 mm
254 mm
24.8°
7'3"
8.5"
10"
1951 mm
165 mm
211 mm
1000 mm
2000 mm
99 mm
3'3.4"
6'7"
3.9"
1406 kg
78 kg
51.6 kN
211.2 kN
24.8°
6'4.8"
6.5"
8.3"
1951 mm
165 mm
211 mm
896 mm
1792 mm
81 mm
2'11.3"
5'10.6"
3.2"
896 mm
1792 mm
89 mm
2'11.3"
5'10.6"
3.5"
3100 lb
172 lb
908 kg
34 kg
2002 lb
75 lb
845 kg
34 kg
1863 lb
75 lb
11,600 lb
47,480 lb
43 kN
170 kN
9666.8 lb
38,218 lb
46 kN
170 kN
10,641 lb
38,218 lb
3
3
6'4.8"
6.5"
8.3"
3
D6K2 XL
D6K2 LGP
D6N XL
Fixed Parallelogram
Fixed Parallelogram
Parallelogram
355 mm
725 mm
14.0"
28.5"
355 mm
725 mm
14.0"
28.5"
355 mm
516 mm
14.0"
1'8.3"
471 mm
18.5"
471 mm
18.5"
422 mm
16.6"
24.8°
1951 mm
165 mm
211 mm
24.8°
6'4.8"
6.5"
8.3"
1951 mm
165 mm
211 mm
896 mm
1792 mm
81 mm
2'11.3"
5'10.6"
3.2"
908 kg
34 kg
43 kN
170 kN
21.4°
6'4.8"
6.5"
8.3"
2200 mm
216 mm
254 mm
896 mm
1792 mm
89 mm
2'11.3"
5'10.6"
3.5"
1000 mm
2000 mm
99 mm
3'3.4"
6'7"
3.9"
2002 lb
75 lb
845 kg
34 kg
1863 lb
75 lb
1406 kg
78 kg
3100 lb
172 lb
9666.8 lb
38,218 lb
46 kN
170 kN
10,641 lb
38,218 lb
51.6 kN
211.2 kN
11,600 lb
47,480 lb
3
3
7'3"
8.5"
10"
3
19-64
Edition 44
12/20/13 8:58 AM
●
TRACTOR/RIPPER
Ripper Type
Dimensions:
Ripper Shank
Shank section
Ripper Beam
O Overall width
P Height
Q Length
Number of Pockets
T Pocket Spacing
U Shank Gauge
Installed weights:
Ripper Forces:*
Penetration Force
Pryout Force
Specifications
D6N LGP ● D6N XL
Rippers
19
D6N LGP
D6N XL
Tier 4 Interim/
Stage IIIB
D6N LGP
Tier 4 Interim/
Stage IIIB
Parallelogram
Parallelogram
Parallelogram
602 mm
453 mm
1'11.7"
17.8"
355 mm
516 mm
14.0"
1'8.3"
602 mm
453 mm
1'11.7"
17.8"
536 mm
1'9.1"
422 mm
16.6"
536 mm
1'9.1"
28.3°
73 × 176 mm 2.9" × 6.9"
2200 mm
216 mm
254 mm
21.4°
—
7'3"
8.5"
10"
2200 mm
216 mm
254 mm
1000 mm
2m
104 mm
3'3.4"
6'7"
4.1"
1406 kg
78 kg
72.9 kN
252 kN
28.3°
73 × 176 mm 2.9" × 6.9"
7'3"
8.5"
10"
2200 mm
216 mm
254 mm
1000 mm
2000 mm
99 mm
3'3.4"
6'7"
3.9"
1000 mm
2m
104 mm
3'3.4"
6'7"
4.1"
3100 lb
172 lb
1406 kg
78 kg
3100 lb
172 lb
1406 kg
78 kg
3100 lb
172 lb
16,389 lb
56,652 lb
51.6 kN
211.2 kN
11,600 lb
47,480 lb
72.9 kN
252 kN
16,389 lb
56,652 lb
3
3
7'3"
8.5"
10"
3
*Tractor equipped with ripper, OROPS, SU dozer and heavy duty track. Values may vary slightly with various configurations. D6N LGP equipped with VPAT-blade
and Power Shift Transmission.
Edition 44
19-65
12/20/13 8:58 AM
Rippers
Specifications
● D6R
● D6R XL
● D6T
● D6T XL
TRACTOR/RIPPER
Ripper Type
Dimensions:
Ripper Shank
Shank section
Ripper Beam
O Overall width
P Height
Q Length
Number of Pockets
T Pocket Spacing
U Shank Gauge
Installed weights:
Ripper Forces:*
Penetration Force
Pryout Force
D6R
D6R XL
Parallelogram
Parallelogram
500 mm
729 mm
1'7.7"
2'4.7"
500 mm
729 mm
1'7.7"
2'4.7"
520 mm
1'8.5"
520 mm
1'8.5"
74 × 175 mm
2.9" × 6.9"
74 × 175 mm
2.9" × 6.9"
2200 mm
216 mm
254 mm
7'3"
8.5"
10"
2200 mm
216 mm
254 mm
7'3"
8.5"
10"
1000 mm
2m
120 mm
3'3.4"
6'7"
4.7"
1000 mm
2m
120 mm
3'3.4"
6'7"
4.7"
1596 kg
3511 lb
1596 kg
3511 lb
64.2 kN
89.6 kN
14,428 lb
20,140 lb
64.2 kN
89.6 kN
14,428 lb
20,140 lb
26°
3
TRACTOR/RIPPER
Ripper Type
Dimensions:
Ripper Shank
Shank section
Ripper Beam
O Overall width
P Height
Q Length
Number of Pockets
T Pocket Spacing
U Shank Gauge
Installed weights:
Ripper Forces:*
Penetration Force
Pryout Force
26°
3
D6T
D6T XL
Parallelogram
Parallelogram
500 mm
729 mm
1'7.7"
2'4.7"
500 mm
729 mm
1'7.7"
2'4.7"
520 mm
1'8.5"
520 mm
1'8.5"
74 × 175 mm
2.9" × 6.9"
74 × 175 mm
2.9" × 6.9"
2.20 m
216 mm
254 mm
7'3"
8.5"
10"
2.20 m
216 mm
254 mm
7'3"
8.5"
10"
1000 mm
2m
120 mm
3'3.4"
6'7"
4.7"
1000 mm
2m
120 mm
3'3.4"
6'7"
4.7"
1456 kg
70 kg
3203 lb
154 lb
1456 kg
70 kg
3203 lb
154 lb
65.2 kN
89.6 kN
14,665 lb
20,140 lb
70.6 kN
89.6 kN
15,863 lb
20,140 lb
26°
26°
3
3
*Tractor equipped with ripper, OROPS, SU dozer and heavy duty track. Values may vary slightly with various configurations.
19-66
Edition 44
12/20/13 8:58 AM
●
TRACTOR/RIPPER
Ripper Type
Dimensions:
Ripper Shank
VPAT
VPAT
VPAT
VPAT
Shank section
Ripper Beam
O Overall width
P Height
Q Length
Number of Pockets
T Pocket Spacing
U Shank Gauge
VPAT
Installed weights:
Ripper Forces:*
Penetration Force
VPAT
Pryout Force
D6T XL
●
Specifications
D6T XW ● D6T LGP
Rippers
19
D6T XL
Tier 4 Interim/
Stage IIIB
D6T XW
Tier 4 Interim/
Stage IIIB
D6T LGP
Tier 4 Interim/
Stage IIIB
Parallelogram
Parallelogram
Parallelogram
500 mm
500 mm
733 mm
733 mm
1'8"
1'8"
2'5"
2'5"
500 mm
450 mm
733 mm
586 mm
1'8"
1'6"
2'5"
1'11"
450 mm
450 mm
586 mm
586 mm
1'6"
1'6"
1'11"
1'11"
515 mm
515 mm
1'8"
1'8"
515 mm
565 mm
1'8"
1'10"
565 mm
565 mm
1'10"
1'10"
27.2°
27.2°
29.9°
27.2°
29.9°
29.9°
74 × 175 mm 2.9" × 6.9" 74 × 175 mm 2.9" × 6.9" 74 × 175 mm 2.9" × 6.9"
2.20 m
216 mm
254 mm
7'3"
8.5"
10"
2.20 m
216 mm
254 mm
7'3"
8.5"
10"
2.20 m
216 mm
254 mm
1000 mm
2m
120 mm
374 mm
3'3"
6'7"
4.7"
1'3"
1000 mm
2m
69 mm
374 mm
3'3"
6'7"
2.7"
1'3"
1000 mm
2m
171 mm
374 mm
3'3"
6'7"
6.7"
1'3"
1634 kg
74 kg
3606 lb
163 lb
1634 kg
74 kg
3606 lb
163 lb
1634 kg
74 kg
3606 lb
163 lb
64.0 kN
60.9 kN
89.6 kN
14,380 lb
13,685 lb
20,140 lb
66.1 kN
68.3 kN
89.6 kN
14,850 lb
15,350 lb
20,140 lb
70.6 kN
68.8 kN
89.6 kN
15,880 lb
15,460 lb
20,140 lb
3
3
7'3"
8.5"
10"
3
*Tractor equipped with ripper, cab, SU dozer, and standard track.
Edition 44
19-67
12/20/13 8:58 AM
Rippers
Specifications
● D7R
TRACTOR/RIPPER
Ripper Type
Dimensions:
Ripper Shank
M Maximum ground clearance under tip (shank pinned in bottom hole)
N Maximum ramp angle, ripper up (shank pinned in bottom hole)
Shank section
Ripper Beam
O Overall width
P Height
Q Length
Number of Pockets
T Pocket Spacing
U Shank Gauge
Installed weights:
Ripper Forces:*
Penetration Force
Pryout Force
D7R
Adjustable Parallelogram
748 mm
1.07 m
638 mm
2'5.4"
3'6.1"
2'1.1"
26.6°
72 × 228 mm
2.8" × 6.9"
2.21 m
279 mm
343 mm
7'3"
11"
13.5"
3
991 mm
1.98 m
95 mm
3'3"
6'6"
3.7"
3277 kg
138 kg
7225 lb
305 lb
85.0 kN
176.6 kN
19,104 lb
39,705 lb
*Tractor equipped with ripper, OROPS, SU dozer and heavy duty track. Values may vary slightly with various configurations.
19-68
Edition 44
12/20/13 8:58 AM
●
TRACTOR/RIPPER
Specifications
D7E ● D8R/D8T
Rippers
D7E
D8R/D8T
Multi-shank
Single Shank
Multi-shank
19
Ripper Type
Dimensions:
Ripper to Track
Ripper length behind track,
shank vertical, ripper up
A With Pushblock
N/A
N/A
N/A
B Without Pushblock
1222 mm
4'0"
1.69 m
5'7"
1.6 m
5'2"
shank vertical, ripper down
C With Pushblock
N/A
N/A
N/A
D Without Pushblock
1660 mm
5'5"
1.84 m
6'0"
1.71 m
5'7"
Tip to track distance, shank vertical
E Ripper Up
614 mm
2'0"
694 mm
2'3.3"
640 mm
2'1.2"
F Ripper Down
970 mm
3'2"
950 mm
3'1.4"
899 mm
2'11.4"
Ripper Shank*
650 mm
2'2"
1130 mm
3'8.5"
780 mm
2'6.7"
H Dig adjustment per hole
230 mm
9"
305 mm
12"
250 mm
10"
I Total dig adjustment
230 mm
9"
610 mm
2'0"
250 mm
10"
Pitch Adjustment, ripper down:
J Forward
16°
15°
14.9°
K Backward
12°
9.9°
10°
1156 mm
3'10"
1.32 m
4'3"
1.17 m
3'10"
M Maximum ground clearance under tooth
588 mm
1'11"
636 mm
2'1"
593 mm
1'11.3"
26°
28.2°
28.4°
Shank Section
72 × 228 mm 2.8" × 9.0" 75 × 333 mm 2.9" × 13.1" 75 × 333 mm 2.9" × 13.1"
Ripper Beam
2088 mm
6'10"
N/A
2.46 m
8'1"
O Overall width
P Height**
355.6 mm
14"
N/A
334 mm
13.1"
(dia)
(dia)
Q Length**
—
N/A
457 mm
18"
Clearance under beam, shank vertical
R Ripper Up
1080 mm
3'7"
N/A
1.55 m
5'1"
S Ripper Down
145 mm
5.7"
N/A
449 mm
17.7"
Number of Pockets
3
1
3
T Pocket Spacing
900 mm
2'11"
N/A
1092 mm
3'7"
U Shank Gauge
1800 mm
5'11"
N/A
2.17 m
7'1"
V Track Clearance with standard shoe
47 mm
1.9"
76 mm
3"
76 mm
3"
W Width across widest part of lift cylinders
1275 mm
4'2"
1.37 m
4'5"
1.37 m
4'5"
Installed Weights:
1650 kg
3572 lb
4085 kg
9005 lb
4213 kg
9287 lb
Each additional tooth group
150 kg
330 lb
N/A
332 kg
730 lb
Ripper Forces:***
Penetration Force, shank vertical
87.4 kN
19,639 lb
127.4 kN
28,620 lb
124.2 kN
27,920 lb
Pryout Force, shank vertical
234.4 kN
52,695 lb
222.8 kN
50,070 lb
227.9 kN
51,230 lb
***Deep Ripping Shank is available for D8R/D8T single shank rippers. Hydraulic pin puller is standard with deep ripping shank. Deep Ripping Arrangement
maximum digging depth is 1.57 m (5'2") for D8R/D8T.
***D7E ripper beam circular cross section.
***Forces for D7E are for machine equipped with SU-blade and standard track. Forces for D8R/D8T are for a ripper on a tractor equipped with EROPS, U-Dozer
and performance track. Forces will vary slightly with other vehicle configurations.
Edition 44
19-69
12/20/13 8:58 AM
Rippers
Specifications
● D9R/D9T
TRACTOR/RIPPER
D9R/D9T
Ripper Type
Dimensions:
Ripper to Track
shank vertical, ripper up
A With Pushblock
B Without Pushblock
shank vertical, ripper down
C With Pushblock
D Without Pushblock
Tip to track distance, shank vertical
E Ripper Up
F Ripper Down
Ripper Shank*
J Forward
K Backward
Shank Section
Ripper Beam
O Overall width
P Height
Q Length
R Ripper Up
S Ripper Down
Number of Pockets
T Pocket Spacing
U Shank Gauge
Installed Weights:
Ripper Forces:**
Single Shank
Multi-shank
N/A
1.57 m
N/A
5'2"
1.33 m
1.88 m
6'2"
1.71 m
5'7"
689 mm
944 mm
2'3.2"
3'1.2"
510 mm
890 mm
1'8.1"
2'11"
1231 mm
295 mm
590 mm
4'0.6"
12"
1'11.2"
798 mm
250 mm
250 mm
2'7.6"
10"
10"
N/A
4'4"
N/A
10.6°
15.2°
10°
15.1°
1.25 m
4'1"
1.16 m
3'10"
882 mm
2'10.9"
885 mm
2'10.7"
3.5" × 14"
75 × 333 mm
2.9" × 13.1"
N/A
N/A
N/A
2.64 m
380 mm
457 mm
8'8"
15"
18"
N/A
N/A
1
N/A
N/A
1.77 m
378 mm
5'10"
14.9"
36.9°
90 × 355 mm
71 mm
1.50 m
37.5°
3
1180 mm
2.35 m
71 mm
1.50 m
3'10.4"
7'8"
2.8"
4'11"
10,700 lb
4885 kg
332 kg
10,770 lb
733 lb
34,581 lb
72,025 lb
148.0 kN
324.7 kN
33,249 lb
74,639 lb
2.8"
4'11"
4854 kg
N/A
153.9 kN
320.5 kN
**Deep Ripping Shank is available for D9R/D9T single shank rippers. Hydraulic pin puller is standard with deep ripping shank. Deep Ripping Arrangement maximum
digging depth is 1.66 m (5'5") for D9R/D9T.
**Forces are for a ripper on a tractor equipped with EROPS, U-Dozer and performance track. Forces will vary slightly with other vehicle configurations.
19-70
Edition 44
12/20/13 8:58 AM
●
TRACTOR/RIPPER
Ripper Type
Dimensions:
Ripper to Track
shank vertical, ripper up (A)
A With Pushblock
B Without Pushblock
shank vertical, ripper down (A)
C With Pushblock
D Without Pushblock
Tip to track distance, shank vertical (A)
E Ripper Up*
F Ripper Down**
Ripper Shank***
G Maximum digging depth**
J Forward
K Backward
L Maximum reach at ground line**
M Maximum ground clearance under
tooth (shank pinned in bottom hole)
Shank Section
Ripper Beam
O Overall width
P Height
Q Length
R Ripper Up
S Ripper Down
Number of Pockets
T Pocket Spacing
U Shank Gauge
W Width across widest part
of lift cylinders
Installed Weights:
Ripper Forces:****
Specifications
D10T2 ● D11T
Rippers
19
D10T2
D11T
D11T
Adjustable
Parallelogram
CD Single Shank
CD Multi-shank
Single Shank
Multi-shank
2.08 m
1.76 m
6'10"
5'9"
1.56 m
5'1"
2.29 m
1.97 m
7'6"
6'6"
2.26 m
2.48 m
2.16 m
8'2"
7'1"
1.96 m
6'5"
2.71 m
2.39 m
8'11"
7'10"
2.52 m
8'3"
730 mm
1130 mm
2'4.7"
3'8.5"
651 mm
1050 mm
2'1.6"
3'5.3"
751 mm
1174 mm
2'6"
3'10"
751 mm
1174 mm
2'6"
3'10"
1494 mm
355 mm
710 mm
4'11"
14"
2'4"
876 mm
250 mm
250 mm
2'10.5"
10"
10"
1590 mm
280 mm
840 mm
5'3"
11"
2'9.1"
1510 mm
280 mm
840 mm
4'11"
11"
2'9.1"
15.4°
29.7°
1.60 m
5'3"
930 mm
3'1"
35.7°
100 × 400 mm
(4" × 15.75")
N/A
N/A
18.1°
23.2°
1.39 m
4'7"
1120 mm
3'8"
50.9°
90 × 355 mm
(3.5" × 14")
N/A
N/A
N/A
2.92 m
1350 mm
990 mm
9'7"
4'5"
3'3"
N/A
N/A
1
N/A
N/A
2.03 m
380 mm
6'8"
15"
3
97 mm
4"
1320 mm
2.63 m
97 mm
1.75 m
5'9"
1.75 m
5'9"
6919 kg
524 kg
15,253 lb
1155 lb
7150 kg 15,763 lb
N/A
4'4"
8'8"
4"
15°
31.9°
1.87 m
6'2"
1150 mm
3'9"
N/A
7'5"
N/A
13°
31.9°
1.87 m
6'2"
1150 mm
3'9"
34.1°
110 × 450 mm
(4.3" × 17.7")
34.1°
110 × 450 mm
(4.3" × 17.7")
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
1
N/A
N/A
141 mm
5.6"
1.90 m
6'3"
N/A
N/A
1
N/A
N/A
141 mm
5.6"
1.90 m
6'3"
9356 kg 20,626 lb 12 733 kg 28,071 lb
N/A
N/A
207.9 kN 46,715 lb 191.4 kN 43,023 lb 288.5 kN 84,850 lb 326.3 kN 73,361 lb
481.7 kN 108,251 lb 484.9 kN 109,022 lb 622.7 kN 139,998 lb 641.8 kN 144,288 lb
****With Standard Shank pinned in the bottom hole.
****With Standard Shank pinned in the top hole.
****Deep Ripping Shank is available for the D10T2 and D11T single shank rippers. Deep Ripping Arrangement maximum digging depth is 1.80 m (5'11") for
the D10T2 and 2.17 m (7'1") for the D11T.
****Forces are for a ripper on a tractor equipped with an EROPS, U-Dozer and performance track. Forces will vary slightly with other machine configurations.
Edition 44
19-71
12/20/13 8:58 AM
Rippers
Specifications
● D11T
TRACTOR/RIPPER
Ripper Type
Dimensions:
Ripper to Track
shank vertical, ripper up (A)
A With Pushblock
B Without Pushblock
shank vertical, ripper down (A)
C With Pushblock
D Without Pushblock
Tip to track distance, shank vertical (A)
E Ripper Up
F Ripper Down
Shank*
J Forward
K Backward
Shank Section
Ripper Beam
O Overall width
P Height
Q Length
R Ripper Up
S Ripper Down
Number of Pockets
T Pocket Spacing
U Shank Gauge
Installed Weights:
Ripper Forces:**
D11T
D11T
CD Multi-shank
Multi-shank
N/A
1.71 m
N/A
5'8"
1.69 m
2.16 m
7'1"
2.16 m
7'1"
0.78 m
1.96 m
2'7"
6'5"
0.78 m
1.95 m
2'7"
6'5"
1.01 m
280 mm
280 mm
3'4"
11"
11"
1.01 m
280 mm
280 mm
3'4"
11"
11"
N/A
5'6"
N/A
12.2°
31.8°
12.2°
31.8°
1.71 m
5'7"
1.71 m
5'7"
1.14 m
3'9"
1.16 m
3'10"
100 × 400 mm
3.9" × 15.7"
100 × 400 mm
3.9" × 15.7"
3.33 m
1.98 m
1.01 m
10'11"
6'6"
3'4"
3.33 m
1.98 m
1.01 m
10'11"
6'6"
3'4"
2.06 m
282 mm
6'9"
11.1"
2.06 m
282 mm
6'9"
11.1"
1500 mm
2.99 m
166 mm
1.9 m
5'9"
9'10"
5.6"
6'3"
1500 mm
2.99 m
166 mm
1.9 m
5'9"
9'10"
5.6"
6'3"
12 026 kg
668 kg
26,513 lb
1472 lb
9251 kg
668 kg
20,395 lb
1472 lb
305.8 kN
650.0 kN
68,739 lb
146,118 lb
277.1 kN
646.4 kN
62,297 lb
145,310 lb
36.4°
36.4°
3
3
**Hydraulic pin puller is standard with deep ripping shank. Deep Ripping Arrangement maximum digging depth is 2.18 m (7'2").
**Forces are for a ripper on a tractor equipped with an EROPS, U-Dozer and performance track. Forces will vary slightly with other vehicle configurations.
19-72
Edition 44
12/20/13 8:58 AM
Tip Selection
Estimating Production
TIP SELECTION FOR THE D8R/D8T, D9R/D9T,
D10T2 AND D11T RIPPERS
Three tip configurations (short, intermediate and long)
in two styles (centerline and penetration) are available
for economical operation in a variety of conditions.
RECOMMENDED TIP USAGE
Short — Use in high impact conditions where breakage
problems occur. The shorter the tip, the more
it resists breakage.
Intermediate — Most effective in moderate impact conditions where abrasion is not excessive.
Long — Use in loose, abrasive materials where breakage is not a problem. Generally offers the most
wear material.
Centerline vs Penetration
The materials being ripped and the tractor doing the
ripping will both have an effect on which tip will do the
best job. High density material requires a “penetration”
tip. High impact material requires a “centerline” tip.
The following is a general guide to tip application.
Tips to use
D8R/D8T
Ripping Condition
D9R/D9T D10T2
Tandem Tractors . . . . . . . . . Short
Short
Single Shank and
Multi-shank
Extreme Duty . . . . . . . . . . Int.
Short
Medium Duty. . . . . . . . . . Long
Int.
Abrasive Duty . . . . . . . . . Long
Long
D11T
Short
Short
Int.
Long
Always use the longest tip that will wear without excessive breakage. Different tips should be tried to determine
the most economical.
ESTIMATING RIPPING PRODUCTION
Ripping costs must be compared to other methods
of loosening the material — usually drilling and blasting — on a cost per ton or bank cubic yard basis. Thus,
an accurate estimation of ripper production is needed
to determine unit ripping costs.
Rippers
There are three general methods of estimating ripping
production:
1. The best method is to record the time spent ripping,
then remove (using scrapers or loaders and trucks)
and weigh the ripped material. The total weight
divided by the time spent will give hourly production. If the contractor is paid by volume, then a
density must be used and the accuracy is only as
good as the density used. For payment by volume
removed, method 2 may be desirable. Some care
will be needed to assure that only ripped material
is removed.
2. Another method is to cross-section the area and
then record the time spent ripping. After the material has been removed, cross-section the area again
to determine the volume of rock removed. The volume divided by the time spent ripping gives the ripping rate per minute or hour.
3. Timing the ripper over a measured distance is the
least accurate method, but valuable for quick estimating on the job. An average cycle time should
be determined from a number of timed cycles.
Turn-around or back-up time must be included.
Measure the average rip distance, rip spacing and
depth of penetration. This data will give the volume
per cycle from which the production in bank cubic
yards can be calculated. Experience has shown
results obtained from this method are about 10 to
20% higher than the more accurate method of crosssectioning.
An example of the measured distance method for
calculating ripper production is:
Data — D10T2 — No. 10 with one shank.
910 mm (36 in) between passes.
1.6 km/h (1 mph) average speed (including slippage
and stalls).
Every 91 m (300 ft) requires 0.25 min to raise, pivot,
turn, and lower again: 91 m (300 ft) = 1 pass.
610 mm (24 in) penetration.
Full time ripping (no pushing or dozing assignment).
Edition 44
19
19-73
12/20/13 8:58 AM
Rippers
Example of Estimating Production (Metric)
Sample problem (Metric)
Time per pass:
Determine the loosening costs in the following situation:
Machine
— D10T2 Tractor with No. 10
Single Shank Ripper
Rip Spacing
— 915 mm
Ripper Penetration — 610 mm
Rip Distance
— 91 m
Rip Time
— 3.41 minutes
Maneuver Time
— 0.25 minutes
Seismic Velocity — 1830 meters per second
Assume 60 min. hour
Solution:
1. Total Cycle Time = 3.41 + 0.25 = 3.66 min
60 min/hr
Cycles/hour =
= 16.4
3.66 min/cycle
91 m
= 3.41 min;
26.7 m/min
3.41 min + 0.25 min (turn time) = 3.66 min/pass.
1.6 km/h = 26.7 m/min. Then
If the operator works an average of 45 min per h, it is
45
possible to make =
= 12.3 passes per h
3.66
Volume ripped: 91 m × 0.9 m × 0.6 m = 49.1 BCM
per pass
Production = 49.1 × 12.3 = 604 BCM per h
Remember the results from this method are usually
10 to 20 per cent higher than the actual production
that can be expected on the job.
● ● ●
Example of Estimating Production (English)
Time per pass:
300 ft
= 3.41 min;
88 fpm
3.41 min + 0.25 min. (turn time) = 3.66 min/pass.
MPH = 88 fpm. Then
If the operator works an average of 45 min per h, it is
45
possible to make =
= 12.3 passes per h
3.66
300 × 3 × 2
Volume ripped:
= 66.7 BCY per pass
27
Production = 66.7 × 12.3 = 820 BCY per hr
● ● ●
NOTE: The demands of heavy ripping will increase the
normal owning and operating costs of the tractor.
These costs should be increased no less than 30-40%
in heavy ripping applications to estimate rock loosening costs.
There is no ready answer or rule-of-thumb solution to
predict ripping production. Even if everything is known
about the seismic velocity of the material, its composition, job conditions, equipment and operator, only a
“guesstimate” can be given. The final answer must come
from a production study obtained on the job site.
19-74
2. Production per cycle = 91 m × 0.9 m × 0.6 m =
49.1 BCM/cycle
3. Production = 49.1 BCM/cycle × 16.4 cycles/h =
805 BCM/h
4. Remember results of this method are usually 10 to
20% high.
Actual Production
= 80% of 805 BCM/h
= 644 BCM/h
Or 90% of 805 BCM/h = 725 BCM/h
5. Owning and Operating Costs
A D10T2 (ripping only) could have a $115.00/h
O & O costs including $30/h operator.
6. Loosening Costs
$115.00/hr ÷ 644 BCM/h = $0.179/BCM
$115.00/hr ÷ 725 BCM/h = $0.159/BCM
The loosening cost should range from 15.9¢ to
17.9¢/BCM
● ● ●
Sample problem (English)
Determine the loosening costs in the following situation:
Machine
— D10T2 Tractor with No. 10
Single Shank Ripper
Rip Spacing
— 3 feet
Ripper Penetration — 2 feet
Rip Distance
— 300 feet
Rip Time
— 3.41 minutes
Maneuver Time
— 0.25 minutes
Seismic Velocity — 6000 feet per second
Assume 60 min. hour
Edition 44
12/20/13 8:58 AM
Using Seismic Charts
Solution:
1. Total Cycle Time = 3.41 + 0.25 = 3.66 min
60 min/hr
Cycles/hour =
= 16.4
3.66 min/cycle
300 × 3 × 2
2. Production per cycle =
=
27
66.7 BCY/cycle
3. Production = 66.7 BCY/cycle × 16.4 cycles/hr
= 1094 BCY/hour
4. Remember results of this method are usually 10 to
20% high.
Actual Production = 80% × 1094
= 875 BCY/hr
or 90% × 1094
= 984 BCY/hr
5. Owning and Operating Costs
A D10T2 (ripping only) could have a $115.00/hr
O & O costs including $30/hr operator
6. Loosening Costs
$115.00/hr ÷ 875 BCY/hr = $0.131/BCY
$115.00/hr ÷ 984 BCY/hr = $0.117/BCY
The loosening cost should range from 11.7¢ to
13.1¢/BCY
Rippers
19
— Low seismic velocities of sedimentaries can indicate probable rippability. However, if the fractures
and bedding joints do not allow tooth penetration, the material may not be ripped effectively.
— Pre-blasting or “popping” may induce sufficient
fracturing to permit tooth entry, particularly in
the caliches, conglomerates and some other rocks;
but the economics should be checked carefully
when considering popping in the higher grades of
sandstones, limestones and granites.
Ripping is still more art than science, and much will
depend on operator skill and experience. Ripping for
scraper loading may call for different techniques than
if the same material is to be dozed away. Cross-ripping
requires a change in approach. The number of shanks
used, length and depth of shank, tooth angle, direction, throttle position — all must be adjusted according
to field conditions. Ripping success may well depend
on the operator finding the proper combination for
those conditions.
● ● ●
USE OF SEISMIC VELOCITY CHARTS
The charts of ripper performance estimated by seismic wave velocities have been developed from field tests
conducted in a variety of materials. Considering the
extreme variations among materials and even among
rocks of a specific classification, the charts must be recognized as being at best only one indicator of rippability.
Accordingly, consider the following precautions when
evaluating the feasibility of ripping a given formation:
— Tooth penetration is often the key to ripping success, regardless of seismic velocity. This is particu larly true in homogeneous materials such as
mudstones and claystones and the fine-grained
caliches. It is also true in tightly cemented formations such as conglomerates, some glacial tills and
caliches containing rock fragments.
Edition 44
19-75
12/20/13 8:58 AM
Rippers
Ripper Performance
● D8R/D8T
D8R/D8T
● Multi- or Single Shank No. 8 Ripper
● Estimated by Seismic Wave Velocities
0
Seismic Velocity
1
Meters Per Second × 1000
1
Feet Per Second × 1000
TOPSOIL
CLAY
GLACIAL TILL
IGNEOUS ROCKS
GRANITE
BASALT
TRAP ROCK
SEDIMENTARY ROCKS
SHALE
SANDSTONE
SILTSTONE
CLAYSTONE
CONGLOMERATE
BRECCIA
CALICHE
LIMESTONE
METAMORPHIC ROCKS
SCHIST
SLATE
MINERALS and ORES
COAL
IRON ORE
RIPPABLE
19-76
Edition 44
2
3
;
;
3
2
4
5
6
MARGINAL
7
8
9
10
4
11
12
13
14
15
NON-RIPPABLE
12/20/13 8:58 AM
;;
Ripper Performance
● D9R/D9T
D9R/D9T
0
Seismic Velocity
1
1
TOPSOIL
CLAY
GLACIAL TILL
IGNEOUS ROCKS
GRANITE
BASALT
TRAP ROCK
SEDIMENTARY ROCKS
SHALE
SANDSTONE
SILTSTONE
CLAYSTONE
CONGLOMERATE
BRECCIA
CALICHE
LIMESTONE
METAMORPHIC ROCKS
SCHIST
SLATE
MINERALS and ORES
COAL
IRON ORE
RIPPABLE
2
3
4
5
6
MARGINAL
7
19
3
2
Rippers
8
9
10
4
11
12
13
14
NON-RIPPABLE
Edition 44
15
19-77
12/20/13 8:58 AM
Rippers
Ripper Performance
● D10T2
D10T2
0
Seismic Velocity
1
1
TOPSOIL
CLAY
GLACIAL TILL
IGNEOUS ROCKS
GRANITE
BASALT
TRAP ROCK
SEDIMENTARY ROCKS
SHALE
SANDSTONE
SILTSTONE
CLAYSTONE
CONGLOMERATE
BRECCIA
CALICHE
LIMESTONE
METAMORPHIC ROCKS
SCHIST
SLATE
MINERALS and ORES
COAL
IRON ORE
RIPPABLE
19-78
Edition 44
2
3
;
;
3
2
4
5
6
MARGINAL
7
8
9
10
4
11
12
13
14
15
NON-RIPPABLE
12/20/13 8:58 AM
;
;
Ripper Performance
● D11T
D11T
Seismic Velocity
0
1
1
GLACIAL TILL
IGNEOUS ROCKS
GRANITE
BASALT
TRAP ROCK
SEDIMENTARY
SHALE
SANDSTONE
SILTSTONE
CLAYSTONE
CONGLOMERATE
BRECCIA
CALICHE
LIMESTONE
METAMORPHIC
SCHIST
SLATE
MINERALS and ORES
COAL
IRON ORE
RIPPABLE
2
3
4
5
6
MARGINAL
7
19
3
2
Rippers
8
9
10
4
11
12
13
14
NON-RIPPABLE
Edition 44
15
19-79
12/20/13 8:58 AM
Rippers
Ripper Performance
● D11T CD
D11T CD
● Single Shank No. 11 Ripper
Seismic Velocity
0
1
1
GLACIAL TILL
IGNEOUS ROCKS
GRANITE
BASALT
TRAP ROCK
SEDIMENTARY
SHALE
SANDSTONE
SILTSTONE
CLAYSTONE
CONGLOMERATE
BRECCIA
CALICHE
LIMESTONE
METAMORPHIC
SCHIST
SLATE
MINERALS and ORES
COAL
IRON ORE
RIPPABLE
19-80
Edition 44
2
3
;
;
3
2
4
5
6
MARGINAL
7
8
9
10
4
11
12
13
14
15
NON-RIPPABLE
12/20/13 8:58 AM
Estimated Ripper Production Graphs
● D8R/D8T
● D9R/D9T
19
D9R/D9T WITH SINGLE SHANK
2500
3250
Machine rips full-time — no dozing.
●
Power shift tractors with single shank rippers.
3000
●
100% efficiency (60 min hour).
2750
●
Charts are for all classes of material.
●
In igneous rock with seismic velocity of 8000 fps
(2450 mps) or higher for the D11T, and 6000 fps
(1830 mps) or higher for the D10T2, D9R/D9T and
D8R/D8T, the production figures shown should be
reduced by 25%.
PRODUCTION (BCY/hour)
●
Upper limit of charts reflect ripping under ideal conditions only. If conditions such as thick lamination,
vertical lamination or any factor which would adversely
affect production are present, the lower limit should
be used.
2500
2250
2000
A
1750
2250
1500
2000
1750
1250
1500
1250
B
1000
1000
750
750
PRODUCTION (Bm3/hour)
CONSIDERATIONS FOR USING
PRODUCTION ESTIMATED GRAPHS:
●
Rippers
500
500
2750
2000
SEISMIC VELOCITY (in meters per second x 1000)
2500
1750
A
1500
2000
1750
1250
1500
1250
1000
B
750
1000
3000
2250
2
3
4
5
6
7
8
SEISMIC VELOCITY (in feet per second x 1000)
1
2
2500
3250
2250
250
250
D8R/D8T WITH SINGLE SHANK
KEY
A — IDEAL
B — ADVERSE
750
500
500
250
250
2
3
4
5
6
7
8
1
2
Edition 44
19-81
12/20/13 8:58 AM
Rippers
Estimated Ripper Production Graphs
● D10T2
● D11T
● D11T CD
D10T2 WITH SINGLE SHANK
D11T WITH SINGLE SHANK
3750
5000
2250
2750
2000
2500
1750
2250
1500
2000
1750
B
1250
1500
1000
1250
750
1000
A
4000
3000
3000
2250
1500
2000
B
750
1000
A
3000
3250
2500
750
500
500
2
250
3
4
1
2
3
4
5
6
7
8
9
6
7
8
9
10
2
3
1
5
250
2
D11T CD WITH SINGLE SHANK
KEY
A — IDEAL
B — ADVERSE
3750
5000
3000
3000
2250
1500
2000
B
750
1000
2
3
4
5
6
7
8
9
A
4000
10
1
2
3
19-82
Edition 44
12/20/13 8:58 AM
WINCHES
19
PACCAR
ALLIED
CONTENTS
PACCAR
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19-84
Physical Specifications. . . . . . . . . . . . . . . . . . . .19-85
Operating Specifications . . . . . . . . . . . . . . . . . .19-95
Allied
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19-99
Physical Specifications. . . . . . . . . . . . . . . . . . 19-100
Operating Specifications . . . . . . . . . . . . . . . . .19-107
Edition 44
PHB-Sec19-TTT-5-Winches(pg83-112).indd 83
19-83
12/20/13 8:59 AM
Winches
PACCAR
Features
PACCAR Features:
PA90, PA110B, PA140 and H200
PA40 and PA50
●
Closed loop hydrostatic operation with variable displacement motor and dedicated variable displacement pump
for maximum winching power and flexibility.
Hydraulically driven winch for infinitely variable control of line speed and line pull including positive inching control at maximum rated line pull.
●
Infinitely variable control of line speed and line pull
including positive inching control at maximum rated
line pull.
Optimized “high power” hydraulic control system
including specialized directional control valve for
maximum winching power and flexibility.
●
Dual braking system provides a static brake with sprag
clutch to eliminate fall-back and a hydraulic brake
valve for dynamic braking.
●
Single lever joystick control for ease of operation.
●
Fabricated steel winch case with integral heavy duty
drawbar provides excellent durability and easy weldability.
●
Standard three-roller fairlead for improved wire rope
life during side pulls.
●
●
●
Standard full-function “power-in” and “power-out”
control. This is optional on some competitive winches.
●
Standard “drive-away” to maintain tension on the cable
when driving the tractor away from a stationary load.
●
Standard “free spool” to allow cable to be pulled off
the winch by hand.
●
Durable cast winch case with fairlead mounting lugs,
log arch mounting lugs, and heavy duty drawbar.
PA55, PA56 and PA80
H60, H110B and H140
●
PTO mechanical winch drive with full tractor engine
power available to the winch.
●
●
Self-contained internal hydraulic control system for
easy installation.
Hydraulically driven winch for infinitely variable control of line speed and line pull including positive inching control at maximum rated line pull.
●
Equal speed gearing in “reel-in” and “reel-out” to
provide smooth and predictable performance.
Standard Cat ripper control system is employed for
winch “power-in” and “power-out” functions.
●
Standard “drive-away” to maintain tension on the cable
when driving the tractor away from a stationary load.
Winch installation time is reduced by up to 70% compared to “high power” installations.
●
Easy field interchangeability between winch and ripper.
●
Dual braking system provides a static brake with sprag
clutch to eliminate fall-back and a hydraulic brake
valve for dynamic braking.
●
Durable cast (H60) or fabricated steel (H110B and
H140) winch case with integral heavy duty drawbar.
●
Three-roller fairlead for improved wire rope life during side pulls is standard on H110B and H140 and
optional on H60.
●
“Free spool” to allow cable to be pulled off the winch
by hand is standard on H60.
●
●
●
Standard “free spool” to allow cable to be pulled off
the winch by hand.
●
Durable cast winch case with fairlead mounting lugs,
log arch mounting lugs, and heavy duty drawbar.
19-84
Edition 44
12/20/13 8:59 AM
Physical Specifications
● PA40
● PA50
WINCH MODEL
TRACTOR MODEL
Tractor transmission
Winch drive
A Tractor to rear of winch
B Tractor to drum centerline
C Ground to top of winch
D Ground to drum centerline
E Ground to center of hitch
F Tractor to drawbar pin centerline
Winch width (not shown)1
Drum diameter (not shown)
Weight2
Oil refill capacity
Wire rope diameter:
Recommended
Optional
Maximum theoretical
drum capacity:3
Recommended rope
Optional rope
Maximum recommended
drum capacity:4
Recommended rope
Optional rope
Wire rope ferrule size (OD)
Wire rope ferrule size (length)
PA40
D3K, D4K, D5K (LRC)
D3K2, D4K2, D5K2
Hydrostatic
Hydrostatic
751 mm
29.6"
521 mm
20.5"
1327 mm
52.2"
959 mm
37.8"
473 mm
18.6"
410 mm
16.1"
740 mm
29.2"
255 mm
10.0"
610 kg
1345 lb
4.3 L
4.5 qt
Hydrostatic
Hydrostatic
751 mm
29.6"
521 mm
20.5"
1327 mm
52.2"
959 mm
37.8"
473 mm
18.6"
410 mm
16.1"
740 mm
29.2"
255 mm
10.0"
610 kg
1345 lb
4.3 L
4.5 qt
Winches
PACCAR
19
PA50
D6K, D6K2
Hydrostatic
Hydrostatic
845 mm
33.2"
615 mm
24.2"
1380 mm
54.4"
1010 mm
39.8"
525 mm
20.7"
505 mm
19.8"
740 mm
29.2"
205 mm
8.0"
610 kg
1345 lb
4.3 L
4.5 qt
16 mm
19 mm
0.63"
0.75"
16 mm
19 mm
0.63"
0.75"
19 mm
22 mm
0.75"
0.88"
114 m
80 m
374'
264'
114 m
80 m
374'
264'
93 m
67 m
306'
220'
83 m
55 m
54 mm
67 mm
272'
180'
2.13"
2.63"
83 m
55 m
54 mm
67 mm
272'
180'
2.13"
2.63"
62 m
56 m
54 mm
67 mm
203'
183'
2.13"
2.63"
1
Width does not include mounting brackets/adapters (if any).
Weight shown is base winch only. Does not include mounting arrangement, control arrangement, oil, or wire rope.
Per SAE J1158.
4
Per SAE J706 (K=.9).
2
3
Edition 44
19-85
12/20/13 8:59 AM
Winches
PACCAR
● PA55
WINCH MODEL
TRACTOR MODEL
Winch drive
Weight2
Oil refill capacity
Wire rope diameter:
Recommended
Optional
Maximum theoretical drum capacity:3
Recommended rope
Optional rope
Maximum recommended drum capacity:4
Recommended rope
Optional rope
PA55
D5R XL, D6N XL,
Stage IIIB
D5R LGP, D6N LGP,
Stage IIIB
Powershift
PTO
Powershift
PTO
1145 mm
890 mm
1330 mm
960 mm
525 mm
845 mm
975 mm
255 mm
1180 kg
74 L
45.1"
35.1"
52.3"
37.8"
20.7"
33.2"
38.3"
10.0"
2600 lb
19.5 U.S. gal
1145 mm
890 mm
1380 mm
1010 mm
575 mm
845 mm
975 mm
255 mm
1180 kg
74 L
45.1"
35.1"
54.3"
39.8"
22.7"
33.2"
38.3"
10.0"
2600 lb
19.5 U.S. gal
19 mm
22 mm
0.75"
0.88"
19 mm
22 mm
0.75"
0.88"
119 m
85 m
391'
281'
119 m
85 m
391'
281'
81 m
55 m
54 mm
67 mm
267'
180'
2.13"
2.63"
81 m
55 m
54 mm
67 mm
267'
180'
2.13"
2.63"
1
Per SAE J1158.
4
2
3
19-86
Edition 44
12/20/13 8:59 AM
● H60
WINCH MODEL
TRACTOR MODEL
Winch drive
Weight2
Oil refill capacity
Wire rope diameter:
Recommended
Optional
Recommended rope
Optional rope
Recommended rope
Optional rope
Winches
PACCAR
19
H60
D5R XL, D6N XL,
Stage IIIB
Powershift
Hydraulic (Ripper)
1210 mm
47.7"
945 mm
37.7"
1530 mm
60.2"
1160 mm
45.7"
725 mm
28.5"
910 mm
35.8"
975 mm
38.3"
255 mm
10.0"
1180 kg
2600 lb
67 L
17.75 U.S. gal
D5R LGP, D6N LGP,
Stage IIIB
Powershift
Hydraulic (Ripper)
1210 mm
47.7"
945 mm
37.7"
1640 mm
64.7"
1275 mm
50.2"
762 mm
33.0"
910 mm
35.8"
975 mm
38.3"
255 mm
10.0"
1180 kg
2600 lb
67 L
17.75 U.S. gal
22 mm
26 mm
0.88"
1.0"
22 mm
26 mm
0.88"
1.0"
85 m
66 m
281'
218'
85 m
66 m
281'
218'
55 m
50 m
54 mm
67 mm
180'
163'
2.13"
2.63"
55 m
50 m
54 mm
67 mm
180'
163'
2.13"
2.63"
1
Per SAE J1158.
4
2
3
Edition 44
19-87
12/20/13 8:59 AM
Winches
PACCAR
● PA56
WINCH MODEL
TRACTOR MODEL
Winch drive
Weight2
Oil refill capacity
Wire rope diameter:
Recommended
Optional
Recommended rope
Optional rope
Recommended rope
Optional rope
PA56
D6R, D6R XL, D6T,
D6T Tier 4 Interim/Stage IIIB
XL, XL VPAT, XW
D6R LGP, D6T Tier 4 Interim/
Stage IIIB XW VPAT, LGP,
and LGP VPAT
Powershift
PTO
Powershift
PTO
1210 mm
945 mm
1530 mm
1160 mm
725 mm
910 mm
975 mm
255 mm
1180 kg
67 L
47.7"
37.7"
60.2"
45.7"
28.5"
35.8"
38.3"
10.0"
2600 lb
17.75 U.S. gal
1210 mm
945 mm
1580 mm
1210 mm
775 mm
910 mm
975 mm
255 mm
1180 kg
67 L
47.7"
37.7"
62.2"
47.7"
30.5"
35.8"
38.3"
10.0"
2600 lb
17.75 U.S. gal
22 mm
26 mm
0.88"
1.0"
22 mm
26 mm
0.88"
1.0"
85 m
66 m
281'
218'
85 m
66 m
281'
218'
55 m
50 m
54 mm
67 mm
180'
163'
2.13"
2.63"
55 m
50 m
54 mm
67 mm
180'
163'
2.13"
2.63"
1
Per SAE J1158.
4
2
3
19-88
Edition 44
12/20/13 8:59 AM
● H85
WINCH MODEL
TRACTOR MODEL
Winch drive
Weight2
Oil refill capacity
Wire rope diameter:
Recommended
Optional
Recommended rope
Optional rope
Recommended rope
Optional rope
D6T XL, XL VPAT, and XW
Powershift
Hydraulic (Ripper)
1210 mm
47.7"
945 mm
37.7"
1530 mm
60.2"
1160 mm
45.7"
725 mm
28.5"
910 mm
35.8"
975 mm
38.3"
255 mm
10.0"
1180 kg
2600 lb
67 L
17.75 U.S. gal
Winches
PACCAR
19
H85
D6T XW VPAT, LGP, and LGP VPAT
Powershift
Hydraulic (Ripper)
1210 mm
47.7"
945 mm
37.7"
1580 mm
62.2"
1210 mm
47.7"
775 mm
30.5"
910 mm
35.8"
975 mm
38.3"
255 mm
10.0"
1180 kg
2600 lb
67 L
17.75 U.S. gal
22 mm
26 mm
0.88"
1.0"
22 mm
26 mm
0.88"
1.0"
85 m
66 m
281'
218'
85 m
66 m
281'
218'
55 m
50 m
54 mm
67 mm
180'
163'
2.13"
2.63"
55 m
50 m
54 mm
67 mm
180'
163'
2.13"
2.63"
1
Per SAE J1158.
4
2
3
Edition 44
19-89
12/20/13 8:59 AM
Winches
PACCAR
● PA90
● H110B
WINCH MODEL
TRACTOR MODEL
Winch drive
Weight2
Oil refill capacity
Wire rope diameter:
PA90
D7E
H110B
D7E
Electric
Hydraulic
Electric
Hydraulic
1265 mm
755 mm
1665 mm
1235 mm
670 mm
995 mm
1090 mm
320 mm
1520 kg
12 L
49.8"
29.7"
65.6"
48.5"
26.3"
39.2"
43.0"
12.5"
3350 lb
12.5 qt
1265 mm
755 mm
1665 mm
1235 mm
670 mm
995 mm
1160 mm
320 mm
1790 kg
15 L
4'8.5"
3'0.4"
5'6.8"
4'1.5"
2'3.8"
4'0"
3'9.6"
1'0.5"
3950 lb
4 U.S. gal
Recommended
Optional
Recommended rope
Optional rope
26 mm
28 mm
1"
1.13"
28 mm
32 mm
1.13"
1.25"
68 m
54 m
223'
178'
78 m
62 m
257'
204'
Recommended rope
Optional rope
56 m
38 m
60 mm
70 mm
183'
126'
2.38"
2.75"
55 m
36 m
60 mm
70 mm
182'
118'
2.38"
2.75"
1
Per SAE J1158.
4
2
3
19-90
Edition 44
12/20/13 8:59 AM
● PA90
WINCH MODEL
TRACTOR MODEL
Winch drive
Weight2
Oil refill capacity
Wire rope diameter:
Recommended
Optional
Recommended rope
Optional rope
Recommended rope
Optional rope
D6R, D6T Tier 3 XW VPAT
Powershift
Hydraulic (High Power)
1380 mm
4'6"
870 mm
2'10"
1680 mm
5'6"
1235 mm
4'1"
670 mm
2'2"
1160 mm
3'8"
1190 mm
3'7"
320 mm
1'1"
1500 kg
3300 lb
12 L
3.13 U.S. gal
Winches
PACCAR
19
PA90
D6T Tier 3 LGP and LGP VPAT
Powershift
1380 mm
4'6"
870 mm
2'10"
1730 mm
5'8"
1285 mm
4'3"
720 mm
2'4"
1160 mm
3'8"
1190 mm
3'7"
320 mm
1'1"
1500 kg
3300 lb
12 L
3.13 U.S. gal
26 mm
28 mm
1"
1.13"
26 mm
28 mm
1"
1.13"
69 m
55 m
226'
180'
69 m
55 m
226'
180'
57 m
39 m
60 mm
70 mm
186'
128'
2.38"
2.75"
57 m
39 m
60 mm
70 mm
186'
128'
2.38"
2.75"
1
Per SAE J1158.
4
2
3
Edition 44
19-91
12/20/13 8:59 AM
Winches
PACCAR
● H110B
● PA110B
WINCH MODEL
TRACTOR MODEL
Winch drive
Weight2
Oil refill capacity
Wire rope diameter:
Recommended
Optional
Recommended rope
Optional rope
Recommended rope
Optional rope
H110B
D7R
PA110B
D7R
Powershift
Hydraulic (Ripper)
1585 mm
5'2.4"
1075 mm
3'6.3"
1695 mm
5'6.8"
1255 mm
4'1.5"
705 mm
2'3.8"
1370 mm
4'5.9"
1160 mm
3'9.6"
320 mm
1'0.5"
1790 kg
3950 lb
15 L
4 U.S. gal
Powershift
1435 mm
4'8.5"
925 mm
3'0.4"
1695 mm
5'6.8"
1255 mm
4'1.5"
705 mm
2'3.8"
1220 mm
4'0"
1160 mm
3'9.6"
320 mm
1'0.5"
1790 kg
3950 lb
15 L
4 U.S. gal
28 mm
32 mm
1.13"
1.25"
28 mm
32 mm
1.13"
1.25"
78 m
62 m
257'
204'
78 m
62 m
257'
204'
55 m
36 m
60 mm
70 mm
182'
118'
2.38"
2.75"
55 m
36 m
60 mm
70 mm
182'
118'
2.38"
2.75"
1
Per SAE J1158.
4
2
3
19-92
Edition 44
12/20/13 8:59 AM
● H140
● PA140
WINCH MODEL
TRACTOR MODEL
Winch drive
F Tractor to drawbar pin
centerline
Weight2
Oil refill capacity
Wire rope diameter:
Recommended
Optional
Maximum theoretical
drum capacity:3
Recommended rope
Optional rope
Maximum recommended
drum capacity:4
Recommended rope
Optional rope
H140
D8R, D8T
Winches
PACCAR
19
PA140
D9R, D9T
D8R, D8T
D9R, D9T
Powershift
Hydraulic (Ripper)
1585 mm
5'2.4"
1075 mm
3'6.3"
1715 mm
5'7.5"
1275 mm
4'2.1"
725 mm
2'4.5"
Powershift
Hydraulic (Ripper)
1525 mm
5'0.3"
1015 mm
3'4.0"
1740 mm
5'8.4"
1300 mm
4'3.2"
750 mm
2'5.5"
Powershift
Powershift
Hydraulic (High Power) Hydraulic (High Power)
1435 mm
4'8.5"
1620 mm
5'3.8"
925 mm
3'0.4"
1110 mm
3'7.7"
1715 mm
5'7.5"
1740 mm
5'8.4"
1275 mm
4'2.1"
1300 mm
4'3.2"
725 mm
2'4.5"
750 mm
2'5.5"
1370 mm
1160 mm
320 mm
1790 kg
15 L
4'5.9"
3'9.6"
2'0.5"
3950 lb
4 U.S. gal
1255 mm
1160 mm
320 mm
1790 kg
15 L
4'1.5"
3'9.6"
12.5"
3950 lb
4 U.S. gal
1220 mm
1160 mm
320 mm
1790 kg
15 L
4'0"
3'9.6"
12.5"
3950 lb
4 U.S. gal
1350 mm
1160 mm
320 mm
1790 kg5
15 L
4'5.2"
3'9.6"
12.5"
3950 lb5
4 U.S. gal
28 mm
32 mm
1.13"
1.25"
28 mm
32 mm
1.13"
1.25"
28 mm
32 mm
1.13"
1.25"
28 mm
32 mm
1.13"
1.25"
78 m
62 m
257'
204'
78 m
62 m
257'
204'
78 m
62 m
257'
204'
78 m
62 m
257'
204'
55 m
36 m
60 mm
70 mm
182'
118'
2.38"
2.75"
55 m
36 m
60 mm
70 mm
182'
118'
2.38"
2.75"
55 m
36 m
60 mm
70 mm
182'
118'
2.38"
2.75"
55 m
36 m
60 mm
70 mm
182'
118'
2.38"
2.75"
1
Per SAE J1158.
4
5
3700 kg (8150 lb) with counterweight.
2
3
Edition 44
19-93
12/20/13 8:59 AM
Winches
PACCAR
● H200
WINCH MODEL
TRACTOR MODEL
Winch drive
F Tractor to drawbar pin
centerline
Weight2
Oil refill capacity
Wire rope diameter:
Recommended
Optional
Maximum theoretical drum
capacity:3
Recommended rope
Optional rope
Maximum recommended drum
capacity:4
Recommended rope
Optional rope
H200
D8T
D9T
Powershift
1460 mm
57.5"
960 mm
37.7"
1760 mm
69.4"
1240 mm
48.8"
725 mm
28.5"
Powershift
1645 mm
64.8"
1075 mm
42.4"
1735 mm
68.3"
1215 mm
47.9"
700 mm
27.5"
1170 mm
1400 mm
380 mm
3180 kg
16.5 L
46.1"
55"
15"
7015 lb
4.4 U.S. gal
1305 mm
1400 mm
380 mm
3180 kg5
16.5 L
51.3"
55"
15"
7015 lb5
4.4 U.S. gal
35 mm
38 mm
1.38"
1.5"
35 mm
38 mm
1.38"
1.5"
81 m
68 m
266'
224'
81 m
68 m
266'
224'
64 m
42 m
71 mm
79 mm
211'
138'
2.81"
3.12"
64 m
42 m
71 mm
79 mm
211'
138'
2.81"
3.12"
1
Per SAE J1158.
4
5
5080 kg (11,200 lb) with counterweight.
2
3
19-94
Edition 44
12/20/13 8:59 AM
Operating Specifications
British Units of Measure
● Metric Units of Measure
●
WINCH MODEL
TRACTOR MODEL
Tractor transmission. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Winch drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maximum line pull(1) . . . . . . . . . . . . . . . . . lb
Bare Drum
Rated line speed(2) . . . . . . . . . . . . . . . . . fpm
Maximum line speed(3) . . . . . . . . . . . . . fpm
(4)
Full Drum
Metric Units of Measure
Maximum line pull(1) . . . . . . . . . . . . . . . . kN
Bare Drum
Rated line speed(2) . . . . . . . . . . . . . . . m/min
Maximum line speed(3) . . . . . . . . . . . m/min
Full Drum(4) Rated line speed(2) . . . . . . . . . . . . . . . m/min
Winches
PACCAR
PA40
PA50
H60
D3K, D4K,
D5K (LRC)
D6K, D6K2
D5R, D6N
H85
D6T Tier 4
Interim/
Stage IIIB
Hydrostatic
Hydrostatic
Hydrostatic
Hydrostatic
Powershift
Hydraulic
(Ripper)
Powershift
Hydraulic
(Ripper)
40,000
49
132
25,000
78
207
50,000
45
124
26,000
83
230
60,000
33
99
35,000
56
170
85,000
20
64
52,800
32
93
177.9
15
40
111.2
24
63
222.4
14
38
115.7
25
70
266.9
10
30
155.7
17
52
378.5
6
20
259.9
9
28
19
(1)
“Maximum line pull” is lesser of winch catalog rating or calculated maximum line pull at maximum tractor hydraulic system pressure.
“Rated line speed” is calculated maximum line speed at maximum line pull.
“Maximum line speed” is calculated maximum no-load line speed at maximum tractor hydraulic system flow.
(4)
“Full Drum” as defined by SAE J1158.
(2)
(3)
WINCH MODEL
TRACTOR MODEL
Winch drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bare Drum
(4)
Full Drum
Bare Drum
D6R
PA90
D6T
D7E
H110B
D7E
Powershift
Hydraulic
(High Power)
Powershift
Hydraulic
(High Power)
Electric
Hydraulic
(High Power)
Electric
Hydraulic
(Ripper)
90,000
54
87
53,600
85
139
90,000
35
68
53,600
59
114
90,000
32
63
53,600
53
106
110,000
23
45
66,200
38
74
400.3
16
26
238.4
26
42
400.3
10
20
238.4
18
34
400.3
10
19
238.4
16
32
490.3
7
14
295.2
12
23
(1)
(4)
(2)
(3)
Edition 44
19-95
12/20/13 8:59 AM
Winches
PACCAR
● British Units of Measure
WINCH MODEL
TRACTOR MODEL
Winch drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bare Drum
Full Drum(4) Rated line speed(2) . . . . . . . . . . . . . . . . . fpm
Bare Drum
H110B
D7R
PA110B
D7R
Powershift
Hydraulic (Ripper)
Powershift
101,000
24
51
61,000
39
84
110,000
33
100
66,500
54
165
449.3
7
15
271.3
12
25
489.3
10
30
295.8
16
50
(1)
(4)
(2)
(3)
WINCH MODEL
TRACTOR MODEL
H140
D8R, D8T
D9R, D9T
Winch drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Powershift
Hydraulic
(Ripper)
Bare Drum
Bare Drum
PA140
D8T
D9T
Powershift
Hydraulic
(Ripper)
Powershift
Hydraulic
(High Power)
Powershift
Hydraulic
(High Power)
140,000
19
38
84,600
31
63
140,000
17
35
84,600
28
58
140,000
23
46
84,600
38
76
140,000
23
46
84,600
38
76
622.8
6
11
376.3
9
19
622.8
5
10
376.3
8
17
622.8
7
14
376.3
11
23
622.8
7
14
376.3
11
23
(1)
(4)
(2)
(3)
19-96
Edition 44
12/20/13 8:59 AM
Winches
PACCAR
●
WINCH MODEL
TRACTOR MODEL
Winch drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rated line pull(1) . . . . . . . . . . . . . . . . . . . . . lb
Bare Drum
Maximum
line pull(2) . . . . . . . . . . . . . . . . . lb
Full Drum(5)
Slow speed gearing
Bare Drum
(5)
Full Drum
Rated line pull(1) . . . . . . . . . . . . . . . . . . . . kN
Bare Drum
Maximum
line pull(2) . . . . . . . . . . . . . . . . kN
Full Drum(5)
Slow speed gearing
Bare Drum
Full Drum(5)
PA55
D5R, D6N
PA56
D6R, D6T, D6T Tier 4
Interim/Stage IIIB
Powershift
PTO
Powershift
PTO
36,600
69,200
97
147
20,900
54,100
169
257
59,100
89,800
80
130
34,400
76,300
136
224
50,000
69,200
40
61
50,000
69,200
70
107
70,000
89,800
35
58
70,000
89,800
63
103
162.8
307.8
30
45
93.0
240.6
52
78
262.9
399.5
24
40
153.0
153.9
41
68
222.4
307.8
12
19
222.4
307.8
21
33
311.4
399.5
11
18
311.4
399.5
19
31
19
(1)
“Rated line pull” is lesser of winch catalog rating or calculated line pull at maximum tractor PTO output power.
“Maximum line pull” is lesser of calculated line pull at maximum tractor PTO output torque or catalog breaking strength of maximum optional size new
IWRC IPS wire rope.
(3)
“Rated line speed” is calculated line speed at maximum tractor PTO output power.
(4)
“Maximum line speed” is calculated no-load line speed at maximum tractor engine PTO output speed.
(5)
(2)
Edition 44
19-97
12/20/13 8:59 AM
Winches
PACCAR
WINCH MODEL
TRACTOR MODEL
Winch drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bare Drum
Bare Drum
H200
D8T
D9T
Powershift
Powershift
180,000
17
38
112,000
27
61
200,000
17
38
124,500
27
61
800.7
5
11
498.2
8
18
889.6
5
11
553.8
8
18
(1)
“Maximum line pull” is lesser of winch catalog rating or calculated maximum line pull at maximum hydraulic system pressure.
“Rated line speed” is calculated maximum line speed at maximum hydraulic system pressure and flow with winch motor at maximum displacement.
“Maximum line speed” is calculated maximum no-load line speed at maximum hydraulic system flow with winch motor at minimum displacement.
(4)
(2)
(3)
19-98
Edition 44
12/20/13 8:59 AM
Features
Allied Features:
● Over 80 years of reliability on Caterpillar. Allied winches
trace their roots to Hyster winches on Cat tractors
since 1929. Hyster winches joined Allied in 1990, maintaining the same design and part numbers. Existing
dealer parts inventory continues to be interchangeable
to support the thousands of Allied/Hyster winches in
the field.
●
“Plug and Play” design. Winches come complete with
all the necessary parts for simple and easy field installation on any tractor. They do not require “Winch
Ready” packages pre-ordered on the tractors. This simplifies dealer inventory planning.
●
Self-Contained Hydraulics (SCH) design. All hoses,
pump and valve are inside the PTO winch frame,
totally eliminating external leakage.
●
Two families of winches — Power Take-Off (PTO)
driven or Hydraulically driven winches covering D3
through D10 size tractors, the widest in the industry:
●
Winch Selection Guide:
Tractor
PTO
Class
Winch
D3-5K
W3C
D6N
W5C
D6T, D6R
W6G/W6F
D7R, D7E
W8L
D8-9-10T
W12E
Hydraulic
Winch
H4A
H5C
H6H
H8L
H12E
Winches
Allied
●
Product Features:
– Multiple-disk oil clutches and brake on PTO winches
are constantly oil-cooled for long life.
– Freespool with adjustable freespool drag to allow
cable to be pulled out easily by hand.
– Drawbar provides an additional hitch for load towing.
– Brake-off (half-brake) keeps cable tight while the
tractor drives away from the load during towing to
prevent cable bird-nesting.
– Power reel-in and power reel-out.
– Box-section winch frame withstands demanding
side pulls without the need to fairlead.
●
Optional Equipment:
– Fairlead to handle frequent side pulls from all angles.
Strong vertical and horizontal rollers reduce cable
wear to extend cable life.
– Arch works like a raised fairlead to lift loads off
ground for efficient skidding.
– Choice of standard gear ratio for fast operation in
logging, or slow speed gear ratio for fine speed control in pipelaying and power line sagging applications.
– Electronic Control for precise speed control. Simple
plug-in connection makes installation “Plug and
Play” easy.
Edition 44
19
19-99
12/20/13 8:59 AM
Winches
Allied
● H4AT
● H4AH
TRACTOR
REAR FACE
WINCH MODEL
TRACTOR MODEL
H4AT
D3K, D4K, D5K* (LRC)
H4AH
D3K, D4K, D5K* (LRC)
Winch drive
Ripper Hydraulics
Allied Hi-Flow Pump
Winch type
Standard
Hi-Performance
813 mm
2'8"
813 mm
610 mm
2'0"
610 mm
2'0"
1143 mm
3'10"
1143 mm
3'10"
889 mm
2'11"
889 mm
2'11"
584 mm
1'11"
509 mm
1'8"
F Tractor to pin centerline
584 mm
1'11"
584 mm
1'11"
Overall width (not shown)
737 mm
2'5"
737 mm
2'5"
203 mm
8"
203 mm
8"
771 kg
1700 lb
812 kg
1790 lb
19 L
5 U.S. gal
19 L
5 U.S. gal
Weight
Oil refill capacity
2'8"
Wire rope diameter:
Recommended
16 mm
0.63"
16 mm
0.63"
Optional
19 mm
0.75"
19 mm
0.75"
Recommended rope
84 m
277'
84 m
277'
Optional rope
59 m
195'
59 m
195'
38 mm
1.5"
38 mm
1.5"
51 mm
2"
51 mm
2"
Drum capacity:
*Specifications based on representative models marked *. Others similar.
19-100
Edition 44
12/20/13 8:59 AM
● H5CT
● H5CH Hi-P
Winches
Allied
19
TRACTOR
REAR FACE
WINCH MODEL
TRACTOR MODEL
H5CT
D6K, D6K2
H5CH Hi-P
D6K, D6K2
Winch drive
Ripper Hydraulics
Allied Hi-Flow Pump
Winch type
Standard
Hi-Performance
864 mm
2'10"
864 mm
635 mm
2'1"
635 mm
2'10"
2'1"
1117 mm
3'8"
1117 mm
3'8"
787 mm
2'7"
787 mm
2'7"
381 mm
1'3"
381 mm
1'3"
559 mm
1'10"
559 mm
1'10"
813 mm
2'8"
813 mm
2'8"
217 mm
9"
217 mm
9"
Weight
898 kg
1980 lb
902 kg
2050 lb
Oil refill capacity
12.5 L
3.3 U.S. gal
12.5 L
3.3 U.S. gal
Recommended
19 mm
0.75"
19 mm
0.75"
Optional
22 mm
0.88"
22 mm
0.88"
Recommended rope
91 m
298'
91 m
298'
Optional rope
66 m
215'
66 m
215'
51 mm
2"
51 mm
2"
57 mm
2.25"
57 mm
2.25"
Wire rope diameter:
Drum capacity:
Edition 44
19-101
12/20/13 8:59 AM
Winches
Allied
● H6H
● H8L
H6H
H8L
TRACTOR
REAR FACE
WINCH MODEL
TRACTOR MODEL
TRACTOR
REAR FACE
H6H
D6R, D6R XL, D6T,
D6T* Tier 4 Interim/Stage IIIB
XL, XL VPAT, and XW
H8L
D7E*, D7R
Winch drive
Hydraulic
Hydraulic
Winch type
Standard
Hi-Performance
1219 mm
4'0"
1143 mm
940 mm
3'1"
813 mm
2'8"
1549 mm
5'1"
1651 mm
5'5"
1194 mm
3'11"
1270 mm
4'2"
711 mm
2'4"
660 mm
2'2"
940 mm
3'1"
864 mm
2'10"
1041 mm
3'5"
1067 mm
3'6"
254 mm
10"
305 mm
12"
1284 kg
2830 lb
1542 kg
3400 lb
8L
2.1 U.S. gal
15 L
4 U.S. gal
Recommended
22 mm
0.88"
25 mm
1"
Optional
25 mm
1"
28 mm
1.13"
Recommended rope
91 m
297'
102 m
334'
Optional rope
70 m
230'
81 m
267'
51 mm
2"
57 mm
2.25"
57 mm
2.25"
60 mm
2.38"
Weight
Oil refill capacity
3'9"
Wire rope diameter:
Drum capacity:
19-102
Edition 44
12/20/13 8:59 AM
● H12E
Winches
Allied
19
TRACTOR
REAR FACE
WINCH MODEL
TRACTOR MODEL
H12E
D8T*, D9T, D10T2
Winch drive
Hydraulic
Winch type
Standard
1499 mm
4'11"
1168 mm
3'10"
1778 mm
5'10"
1372 mm
4'6"
711 mm
2'4"
1295 mm
4'3"
1245 mm
4'1"
356 mm
14"
2087 kg
4600 lb
27 L
7 U.S. gal
Recommended
29 mm
1.13"
Optional
32 mm
1.25"
Recommended rope
70 m
229'
Optional rope
55 m
182'
57 mm
2.25"
60 mm
2.38"
Weight
Oil refill capacity
Wire rope diameter:
Drum capacity:
Edition 44
19-103
12/20/13 8:59 AM
Winches
Allied
● W6G
● W6F
TRACTOR
REAR FACE
WINCH MODEL
TRACTOR MODEL
Winch drive
Winch type
Weight
Oil refill capacity
Wire rope diameter:
Recommended
Optional
Drum capacity:
Recommended rope
Optional rope
W6G*
D6N
527
W6F*
D6R
PTO
Standard
1194 mm
3'11"
940 mm
3'1"
1422 mm
4'8"
1066 mm
3'6"
584 mm
1'11"
889 mm
2'11"
965 mm
3'2"
254 mm
10"
1542 kg
3400 lb
72 L
19 U.S. gal
PTO
Standard
1041 mm
3'5"
762 mm
2'6"
1549 mm
3'11"
1193 mm
3'11"
711 mm
2'4"
737 mm
2'5"
965 mm
3'2"
254 mm
10"
1360 kg
3000 lb
72 L
19 U.S. gal
PTO
Standard
1244 mm
4'1"
965 mm
3'2"
1549 mm
3'11"
1193 mm
3'11"
711 mm
2'4"
737 mm
2'5"
965 mm
3'2"
254 mm
10"
1360 kg
3000 lb
72 L
19 U.S. gal
22 mm
25 mm
0.88"
1"
22 mm
25 mm
0.88"
1"
22 mm
25 mm
0.88"
1"
87 m
68 m
51 mm
57 mm
287'
223'
2"
2.25"
87 m
68 m
51 mm
57 mm
287'
223'
2"
2.25"
87 m
68 m
51 mm
57 mm
287'
223'
2"
2.25"
*W6F winch is configured for forestry applications, W6G for all other applications.
19-104
Edition 44
12/20/13 8:59 AM
● W6G
● W8L
Winches
Allied
19
TRACTOR
REAR FACE
WINCH MODEL
TRACTOR MODEL
Winch drive
Winch type
Weight
Oil refill capacity
Wire rope diameter:
Recommended
Optional
Drum capacity:
Recommended rope
Optional rope
W6G**
D6R, D6R XL, D6T,
D6R LGP,
D6T* Tier 4 Interim/
D6T Tier 4 Interim/
Stage IIIB XL, XL
Stage IIIB XW VPAT,
VPAT, and XW
LGP, and LGP VPAT
PTO
Standard
1244 mm
4'1"
965 mm
3'2"
1549 mm
3'11"
1193 mm
3'11"
711 mm
2'4"
940 mm
3'1"
965 mm
3'2"
254 mm
10"
1542 kg
3400 lb
72 L
19 U.S. gal
PTO
Standard
1244 mm
4'1"
965 mm
3'2"
1599 mm
5'3"
1243 mm
4'3"
761 mm
2'6"
940 mm
3'1"
965 mm
3'2"
254 mm
10"
1520 kg
3350 lb
72 L
19 U.S. gal
W8L
D7R
PTO
Standard
1245 mm
4'1"
965 mm
3'2"
1600 mm
5'3"
1219 mm
4'0"
610 mm
2'0"
1067 mm
3'6"
1041 mm
3'5"
305 mm
12"
1724 kg
3800 lb
79 L
21 U.S. gal
22 mm
25 mm
0.88"
1"
22 mm
25 mm
0.88"
1"
25 mm
28 mm
1"
1.13"
87 m
68 m
51 mm
57 mm
287'
223'
2"
2.25"
87 m
68 m
51 mm
57 mm
287'
223'
2"
2.25"
84 m
67 m
57 mm
60 mm
275'
220'
2.25"
2.38"
**W6G winch is configured for all applications except forestry applications.
Edition 44
19-105
12/20/13 8:59 AM
Winches
Allied
● W12E
TRACTOR
REAR FACE
WINCH MODEL
TRACTOR MODEL
Winch drive
Winch type
Weight
Oil refill capacity
Wire rope diameter:
Recommended
Optional
Drum capacity:
Recommended rope
Optional rope
W12E
D8T*, D9R, D9T, PL83, PL87
D10T2
PTO
Standard
PTO
Standard
1473 mm
1143 mm
1752 mm
1346 mm
685 mm
1270 mm
1219 mm
355 mm
2880 kg
114 L
4'10"
3'9"
5'9"
4'4"
2'3"
4'2"
4'0"
14"
6350 lb
30 U.S. gal
1473 mm
1143 mm
1752 mm
1346 mm
685 mm
1270 mm
1219 mm
355 mm
4110 kg
114 L
4'10"
3'9"
5'9"
4'4"
2'3"
4'2"
4'0"
14"
9050 lb
30 U.S. gal
28 mm
32 mm
1.13"
1.25"
28 mm
32 mm
1.13"
1.25"
69 m
55 m
57 mm
60 mm
228'
181'
2.25"
2.38"
69 m
55 m
57 mm
60 mm
228'
181'
2.25"
2.38"
19-106
Edition 44
12/20/13 8:59 AM
●
WINCH MODEL
TRACTOR MODEL
Winch drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Winch type. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maximum line pull** . . . . . . . . . . . . . . . . lb
Line speed at . . . . . . . . . . . . . . . . . . . . . fpm
Bare Drum
Typical line pull of . . . . . . . . . . . . . . . . . . . lb
Maximum line speed . . . . . . . . . . . . . . fpm
Maximum line pull** . . . . . . . . . . . . . . . . lb
Line speed at . . . . . . . . . . . . . . . . . . . . . fpm
Full Drum
Maximum line pull** . . . . . . . . . . . . . . . kg
Line speed at . . . . . . . . . . . . . . . . . . . m/min
Bare Drum
Typical line pull of . . . . . . . . . . . . . . . . . . kg
Maximum line speed . . . . . . . . . . . . m/min
Maximum line pull** . . . . . . . . . . . . . . . kg
Full Drum
Winches
Allied
H4AT
D3K, D4K, D5K*
H4AH
D3K, D4K, D5K*
Ripper Hydraulics
Standard
Allied Hi-Flow Pump
Hi-Performance
32,150
34
20,000
46
18,350
48
17,400
81
38,600
94
20,000
100
22,050
98
20,000
176
14 583
10.4
9072
14
8323
14.6
7893
25
17 509
28.7
9072
31
10 002
29.9
9072
54
19
Performance based on standard gear ratio. Optional gear ratios available for different line speed and line pull requirements.
**Based on lower measurement of maximum line pull that the tractor can develop with the standard gear ratio, or the breaking strength of the maximum
recommended wire.
Edition 44
19-107
12/20/13 8:59 AM
Winches
Allied
WINCH MODEL
TRACTOR MODEL
Winch drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Winch type. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maximum line pull* . . . . . . . . . . . . . . . . . lb
Line speed at . . . . . . . . . . . . . . . . . . . . . fpm
Bare Drum
Maximum line pull* . . . . . . . . . . . . . . . . . lb
Line speed at . . . . . . . . . . . . . . . . . . . . . fpm
Full Drum
Maximum line pull* . . . . . . . . . . . . . . . . kg
Bare Drum
Maximum line pull* . . . . . . . . . . . . . . . . kg
Full Drum
H5CT
D6K
H5CH
D6K
Ripper Hydraulics
Standard
Allied Hi-Flow Pump
Hi-Performance
66,700
25
30,000
52
35,950
47
30,000
97
59,750
97
30,000
128
32,200
70
30,000
237
30 255
7.6
13 608
16
16 307
14.3
13 608
30
27 102
29.6
13 608
39
14 606
21.3
13 608
72
*Based on lower measurement of maximum line pull that the tractor can develop with the standard gear ratio, or the breaking strength of the maximum
recommended wire.
19-108
Edition 44
12/20/13 8:59 AM
●
WINCH MODEL
TRACTOR MODEL
Winch drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Winch type. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maximum line pull** . . . . . . . . . . . . . . lb
Line speed at . . . . . . . . . . . . . . . . . . . .fpm
Bare Drum
Typical line pull of . . . . . . . . . . . . . . . . . lb
Maximum line speed . . . . . . . . . . . . .fpm
Line speed at . . . . . . . . . . . . . . . . . . . .fpm
Full Drum
Maximum line pull** . . . . . . . . . . . . . . kg
Line speed at . . . . . . . . . . . . . . . . . m/min
Bare Drum
Typical line pull of . . . . . . . . . . . . . . . . . kg
Maximum line speed . . . . . . . . . . m/min
Full Drum
Winches
Allied
H6H
D6T*, D6R
H8L
D7E
H12E
D8T*, D9T, D10T2
Ripper Hydraulics
Standard
Hydraulic
Standard
Hydraulic
Standard
88,800
58
40,000
69
48,250
60
40,000
129
112,500
29
50,000
65
72,600
47
50,000
106
130,250
22
80,000
76
83,650
35
80,000
119
40 280
18.0
18 144
21.0
21 886
18.0
18 144
39.0
52 029
8.8
22 700
19.8
32 900
14.3
22 700
32.3
59 080
7.0
36 287
23.2
37 943
10.7
36 287
36.3
19
recommended wire.
Edition 44
19-109
12/20/13 8:59 AM
Winches
Allied
WINCH MODEL
TRACTOR MODEL
Winch drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Winch type. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Line speed at . . . . . . . . . . . . . . . . . . . .fpm
Bare Drum
Line speed at . . . . . . . . . . . . . . . . . . . .fpm
Full Drum
Bare Drum
Full Drum
W6F
D6R*, 527
D6N
W6G
D6T*, D6R
PTO
Standard
PTO
Standard
PTO
Standard
88,800
93
40,000
120
71,200
99
40,000
219
88,800
59
40,000
68
88,800
90
40,000
124
88,800
65
40,000
65
88,800
92
40,000
118
40 280
28.3
18 144
37
32 296
30.2
18 144
67
40 280
18.0
18 144
21
40 280
27.4
18 144
38
40 280
19.8
18 144
20
40 280
28.0
18 144
36
recommended wire.
19-110
Edition 44
12/20/13 8:59 AM
●
WINCH MODEL
TRACTOR MODEL
Winch drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Winch type. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Line speed at . . . . . . . . . . . . . . . . . . . .fpm
Bare Drum
Line speed at . . . . . . . . . . . . . . . . . . . .fpm
Full Drum
Bare Drum
Full Drum
Winches
Allied
W8L
D7R,
572R2
D8T,
PL83, PL87
D9T
D10T2
PTO
Standard
PTO
Standard
PTO
Standard
PTO
Standard
112,500
122
50,000
168
81,700
115
50,000
275
138,800
52
80,000
59
138,800
78
80,000
92
138,800
55
80,000
60
138,800
82
80,000
93
138,800
53
80,000
58
138,800
81
80,000
91
51 030
37.2
22 700
51.2
37 058
35.1
22 700
83.8
62 960
15.8
36 287
18.0
62 959
23.8
36 287
28.0
62 960
16.8
36 287
18.3
62 959
25.0
36 287
28.3
62 960
16.2
36 287
17.7
62 959
24.7
36 287
27.7
19
W12E
recommended wire.
Edition 44
19-111
12/20/13 8:59 AM
Notes —
19-112
Edition 44
12/20/13 8:59 AM

Caterpillar Performance Handbook, January 2014

Transcription

Similar documents

Print Brochure - Komatsu America Corp.

- Hawthorne Cat

7 - Elite Lighting