Hard Drives - Retrocomputing.net

Comments

Transcription

Hard Drives - Retrocomputing.net
K Service Source
Hard Drives
SCSI Drives
IDE Drives
K Service Source
Basics
Hard Drive
Basics
IDE Drives - 1
IDE Drives
Intelligent drive electronics, IDE, incorporates controller
hardware into the drive. IDE is offered in 8- and 16-bit
interface types. Eight-bit drives are sometimes referred to
as XT interface drives, and 16-bit drives are sometimes
referred to as AT interface drives.
IDE drives do not use a SCSI bus. Apple computers continue
to use an external SCSI chain, which is supported by a SCSI
chip on the logic board.
Also, Apple’s HD SC Setup works with IDE drives.
Basics
WIDE and FAST SCSI Protocols - 2
WIDE and FAST SCSI Protocols
SCSI chains that use SCSI-2 protocols are faster than SCSI
chains using the original SCSI protocols. Two terms used in
the SCSI-2 protocol are “WIDE” and “FAST.”
The term “WIDE” defines the 2-byte or 4-byte wide data
interface where each data byte uses its corresponding parity
bit. The traditional SCSI-1 interface protocol is 1 byte
wide. “FAST” SCSI is defined as data transfer rates between
5 MHz and 10 MHz.
Check these protocols against individual drives for
comparative data.
Devices using the SCSI-2 WIDE and FAST protocols are
compatible with existing SCSI-1 devices.
K Service Source
Troubleshooting
Hard Drive
Troubleshooting
General/ - 1
General
The Symptom Charts included in this chapter will help you
diagnose specific symptoms related to your product. Because cures
are listed on the charts in the order of most likely solution, try
the first cure first. Verify whether or not the product continues to
exhibit the symptom. If the symptom persists, try the next cure.
(Note: If you have replaced a module, reinstall the original module
before you proceed to the next cure.)
If you are not sure what the problem is, or if the Symptom Charts
do not resolve the problem, refer to the Flowchart for the product
family.
For additional assistance, contact Apple Technical Support.
Troubleshooting
HD SC Setup/ - 2
HD SC Setup
Before you replace any drive hardware, run HD SC Setup to
update the driver on the drive.
HD SC Setup works with SCSI and IDE drives.
K Service Source
Upgrades
Hard Drives
Upgrades
Hard Drive Carrier
SCSI Select
Cable
Drives in Quadra 900/950 - 1
Hard Drive Mechanism
Termination
Resistors
SCSI Select
Switch
Drives in Quadra
900/950
There are three general
procedures for preparing
hard drives for Quadra 900/
950 computers:
• Removing the hard drive
mechanism from the
carrier.
• Removing resistors
from the replacement
drives.
• Connecting the SCSI
select cable.
Upgrades
Drives in Quadra 900/950 - 2
Removing the Hard
Drive
1
SCSI
Select
Cable
2
3
Drive Carrier
Hard Drive
Disconnect the SCSI
select cable from the
hard drive.
Remove the four Phillips
screws.
Slide the drive out of the
carrier.
Upgrades
Drives in Quadra 900/950 - 3
Tab
SCSI
Select
Cable
Terminator
Resistors
Tab
Removing Resistors
from the 160 MB
Hard Drive
Caution: Failure to remove
the terminator resistors can
damage the logic board.
1
2
3
Pull up on the tab and
remove the resistors
from a replacement
160 MB hard drive.
Insert the drive in the
customer’s carrier and
install four screws.
Attach the SCSI select
cable tab-up as shown.
Upgrades
Drives in Quadra 900/950 - 4
SCSI Select
Cable
Tab
Removing Resistors
from the 230 MB
Hard Drive
Caution: Failure to remove
the terminator resistors can
damage the logic board.
Hard Drive
1
2
Terminator
Resistors
3
Using needlenose pliers,
remove the resistors
from a replacement
230 MB drive.
Insert the drive in the
customer’s carrier and
install four screws.
Attach the SCSI select
cable as shown.
Upgrades
Drives in Quadra 900/950 - 5
Terminator
Resistors
Hard Drive
Removing Resistors
from the 400 MB
Hard Drive
Caution: Failure to remove
the terminator resistors can
damage the logic board.
1
2
SCSI Select
Cable
3
Remove the resistors
from a replacement
400 MB drive.
Insert the drive in the
customer’s carrier and
install four screws.
Attach the SCSI select
cable with the tab of its
connector facing down.
Upgrades
Identifying 20SC Rev A & B - 6
Identifying 20SC
Rev A & B
No preliminary steps are
required before you begin
this procedure.
Note: The Hard Drive 20SC
3.5-inch Revision A and
Revision B drives must be
replaced like-for-like.
Identify the revision you
need by matching the
customer’s defective drive
with the replacement drive.
Upgrades
Identifying 20SC Rev A & B - 7
• Revision A replacement
drives ship in an
internal carrier,
component side up.
Revision A (661-0373)
Revision B (661-0612)
• Revision B replacement
drives ship in an
internal carrier,
component side down.
K Service Source
Additional Procedures
Hard Drives
Additional Procedures
Carrier Removal - 1
Carrier Removal
No preliminary steps are
required.
Note: This procedure
applies to hard drive
mechanisms that have been
removed from a computer or
an external hard drive, or to
replacement drive
mechanisms that have not
yet been installed in the
computer.
Caution: Review the ESD
precautions in Bulletins/
Safety.
Additional Procedures
Carrier Removal - 2
Ê
Remove the four screws and
lift the carrier from the
hard drive.
Drive
Carrier
Hard
Drive
Replacement Caution: Be
sure to properly torque the
replacement drive to its
carrier. Failure to do so
could damage the drive. See
“Torque Sequence” in this
chapter.
Note: For information on
returning defective drives,
see “General Return Info”
and refer to the Parts
chapter in this manual.
Additional Procedures
Torque Driver
Hard
Drive
Drive
Carrier
Torque Sequence - 3
Torque Sequence
No preliminary steps are
required before you begin
this procedure.
Note: This procedure applies
to hard drive mechanisms
that have been removed from
a computer or an external
hard drive, or to
replacement drive
mechanisms that have not
yet been installed in the
computer.
Using a torque driver,
Additional Procedures
Torque Sequence - 4
tighten the screws in the
order shown. Torque the
screws with driver to
8.0-inch pounds.
Note: The torque sequence
is the same for all types of
drives and carriers. The
Apple torque driver is
preset to 8 in/lbs.
Additional Procedures
External
Hard Drives
Only
Modifying 5.25-Inch Drives - 5
Modifying 5.25Inch Drives
No preliminary steps are
required before you begin
this procedure.
This section describes
procedures for modifying
5.25-inch replacement
hard drives that are
qualified for external hard
drives. To learn whether a
replacement drive is a
qualified external drive,
refer to compatibility
information in the Service
Source parts database.
Additional Procedures
Modifying 5.25-Inch Drives - 6
Note: The 20 MB and
160 MB external 5.25-inch
replacement hard drives
ship prepared for external
drives. You must modify
other replacement hard
drives for use in external
hard drives.
Ê
Additional Procedures
Modifying 5.25-Inch Drives - 7
1
2
Carrier
Ê
Power Cable
Remove the four
mounting screws and
carrier from the 5.25inch service
replacement hard drive.
Disconnect the power
cable (if attached) from
the replacement drive.
Additional Procedures
Modifying 5.25-Inch Drives - 8
3
Terminator
Resistors
4
SCSI Select Cable
Jumpers
Disconnect the resistors
from the component side
of the replacement drive.
Use needlenose pliers
and pull the resistors
straight up.
Replacement Note: Be
sure that the tab on the
SCSI select cable
connector points toward
the hard drive data cable.
Connect the SCSI select
cable to the three pairs
of pins on the component
side of the drive. Leave
the black jumpers on the
other pins.
Additional Procedures
Modifying 5.25-Inch Drives - 9
5
6
LED
Cable
Connect the LED cable
connector from the
customer’s external
carrier to the component
side of the replacement
drive.
Attach the reconfigured
replacement hard drive
to the customer’s
external carrier with
the four screws.
Note: For information
on returning defective
drives, see “General
Return Info” and refer
to the Service Source
parts database.
Additional Procedures
External Drives Only
Modifying 3.5-Inch Drives - 10
Modifying 3.5Inch Drives
No preliminary steps are
required before you begin
this procedure.
This section describes
procedures for modifying
3.5-inch replacement hard
drives that are qualified for
external hard drives. To
learn whether a replacement
drive is a qualified external
drive, refer to compatibility
information in the Service
Source parts database.
Additional Procedures
Modifying 3.5-Inch Drives - 11
Note: The External 20 MB
SCSI Rev A replacement hard
drive ships prepared for use
in external hard drives. You
must modify other
replacement hard drives for
use in external hard drives.
Ê
Additional Procedures
Modifying 3.5-Inch Drives - 12
1
Power Cable
Terminator Resistors
2
3
Remove the 3.5-inch
replacement hard drive
from its carrier.
Disconnect the power
cable (if attached) from
the replacement drive.
Note: The location of the
terminator resistors
may differ among drives.
Disconnect the three
terminator resistors
from the component side
of the replacement drive.
Use needlenose pliers, if
necessary.
Additional Procedures
Modifying 3.5-Inch Drives - 13
4
Tab
Tab
SCSI
SCSI
Select Cable
Cable
Select
Important: You must
connect the customer’s
SCSI select cable to six
unkeyed pins on the
controller board. Be
aware that SCSI select
cable connectors differ
among drives in both
design and location.
For SCSI select cable
connectors located on the
edge of the drive controller
board:
• Remove any black
jumpers that may be
installed on the outside
pins.
Additional Procedures
Modifying 3.5-Inch Drives - 14
SCSI
Select
Cable
Tab
• Face the tab up and attach
the SCSI cable connector.
For SCSI select cable
connectors located on the
surface of the controller
board:
• Face the SCSI cable
connector tab toward the
center of the drive.
• Attach the connector to
the six pins closest to the
50-pin SCSI connector.
Important: Combinations
of SCSI select
connectors and cables
vary. To verify the
proper position of the
Additional Procedures
Modifying 3.5-Inch Drives - 15
SCSI select cable
connector, connect the
drive to a known-good
Macintosh and choose Get
Info from the Finder’s
File menu. If Get Info
displays the wrong SCSI
ID or drive name,
reverse the tab of the
SCSI select cable
connector.
Ê
Additional Procedures
Customer's
External Carrier
Modifying 3.5-Inch Drives - 16
5
6
LED
Cable
Connect the LED cable
connector from the
customer’s external
carrier to the component
side of the replacement
drive.
Install the reconfigured
replacement hard drive
in the customer’s
external carrier.
Note: For information on
returning defective
drives, see “General
Return Info” and refer
to the Service Source
parts database.
Additional Procedures
General Return Information - 17
General Return
Information
No preliminary steps are
required before you begin
this procedure.
Note: You must return a
defective hard drive to Apple
without the carrier and
cables.
Note: For specific return
requirements, refer to the
Service Source parts
database.
Ê
Additional Procedures
LED Cable
General Return Information - 18
SCSI Select Cable
Hard Drive
Data Cable
Each drive has four cables
that need to be removed
before the hard drive is
returned. They are
• Power cable
• Hard drive data cable
• SCSI select switch cable
• LED cable
Note: For specific return
requirements, refer to the
Service Source parts
database.
Power Cable
Additional Procedures
Setting SCSI ID - 19
Setting SCSI ID
SCSI Select Pins
No preliminary steps are
required before you begin
this procedure.
1
To set the SCSI ID, locate
the drive’s six SCSI
select pins.
Note: The location of the
SCSI select pins varies
among drives.
Generally, the group of
six (occasionally eight)
pins is on the top or side
of the printed circuit
board.
Additional Procedures
Setting SCSI ID - 20
Note: If you are
installing the drive in a
docking station, such as
the DuoDock, Apple
recommends you change
the SCSI ID to 1. If you
are installing the drive
mechanism in an
external drive case,
Apple recommends you
change the SCSI ID to any
number from 2 to 6.
Ê
Additional Procedures
Setting SCSI ID - 21
2
Place jumpers on the
pairs of pins as shown in
the table below.
Note: In the following
table, the SCSI ID
numbers are labeled
across the top and the
pin numbers are labeled
on the side. (The pin
pairs may be labeled
using either the A0-A1A2 pin number
convention or the E1E2-E3 convention. Some
pin pairs may not be
labeled.) The letter “J”
Additional Procedures
Setting SCSI ID - 22
indicates a jumper.
0
1
2
3
4
5
6
7
A0/E1
-
J
-
J
-
J
-
J
A0/E2
-
-
J
J
-
-
J
J
A0/E3
-
-
-
-
J
J
J
J
K Service Source
Parts
Hard Drives
Parts
Bracket, Hard Drive, 2.5”, Pkg. of 2
1
922-0705
Parts
Bracket, Hard Drive, Pkg. of 2
2
922-1426
Parts
Bracket, Hard Drive, with Spacer, Pkg. of 10
3
922-1123
Parts
Cable, Flex, Hard Drive
4
922-1419
Parts
Cable Extender
5
658-8033
Parts
Cable Kit, SCSI Select
6
076-0130
Parts
Cable, SCSI Select, Quantum
7
922-2322
Parts
Cable Terminator (replaced by 922-1185)
8
658-8032
Parts
Cable, Hard Drive, LED (Fits 1’’ Height Drives) (Replaced by 922-0003)
9
590-0527
Parts
Cable, Hard Drive, LED (Fits 1’’ Height Drives) (Replaced by 922-0003)
10
590-0630
Parts
11
Cable, Hard Drive, LED, Amber (Fits 1’’ Height Drives)
Compatibility
This cable can be used with the following drives:
• Quantum ProDrive LPS
• Quantum ProDrive ELS
922-0003
Parts
12
Cable, Hard Drive, LED, Amber (Replaced by 922-1245)
590-0506
Compatibility
This cable can be used with the following drives:
• All 1.6” high 3.5” drives, Quantum ProDrive, Miniscribe,
Rodine
• All Conner drives
Parts
Cable, Hard Drive, LED, Amber
13
922-1245
Compatibility
This cable can be used with the following drives:
• All 1.6” high 3.5” drives, Quantum ProDrive, Miniscribe,
Rodine
• All Conner drives
Parts
14
Cable, LED (400 MB HDA) (replaced by 922-1244)
Compatibility
This cable can be used with the following drives:
• Seagate 400 MB
590-0248
Parts
15
Cable, LED (400 MB HDA)
922-1244
Compatibility
This cable can be used with the following drives:
• Seagate 400 MB
Parts
16
Cable, LED (Red) (Replaced by 922-1243)
590-0237
Compatibility
This cable can be used with the following drives:
• All 1.6” high 3.5” drives, Quantum ProDrive, Miniscribe,
Rodine
• All Conner drives
Parts
Cable, LED (Yellow)
17
922-1243
Compatibility
This cable can be used with the following drives:
• All 1.6” high 3.5” drives, Quantum ProDrive, Miniscribe,
Rodine
• All Conner drives
Parts
Cable, Peripheral Interface
18
658-8034
Parts
19
Cable, Power
590-0260
Parts
Cable, Power, AC, 110 V, Smoke
20
590-0380
Parts
Cable, Power, HDA/CD-ROM
21
922-0051
This power cable is used with the Power Macintosh 7100/66
and 7100/66AV models. It is NOT compatible with the
7100/80 and 7100/80AV models.
Parts
22
Cable, Power
590-0260
Parts
Cable, SCSI Data
23
922-0053
Parts
24
Cable, SCSI Device Select (replaced by 922-1247)
590-0518
Compatibility
This cable can be used with the following drives:
• All 1.6” high 3.5” drives, including 160 MB IBM and
Seagate 400 MB
• Quantum ProDrive LPS 40 MB, 80 MB
Parts
25
Cable, SCSI Select, 230/500 MB HDA’s (Replaced by 922-1248)
590-0794
Compatibility
This cable can be used with the following drives:
• Seagate 500 MB, 1 GB
• Quantum ProDrive LPS 80 MB, 160 MB, 230 MB
• Quantum ProDrive ELS 40 MB, 80 MB, 120 MB, 160 MB,
320 MB
• All 1” high 3.5” IBM drives
• All 1” high 3.5” Conner drives
Parts
26
Cable, SCSI Select, 230/500 MB HDA’S
922-1248
Compatibility
This cable can be used with the following drives:
• Seagate 500 MB, 1 GB
• Quantum ProDrive LPS 80 MB, 160 MB, 230 MB
• Quantum ProDrive ELS 40 MB, 80 MB, 120 MB, 160 MB,
320 MB
• All 1” high 3.5” IBM drives
• All 1” high 3.5” Conner drives
Parts
27
Cable, SCSI Select, 400 MB HDA (Replaced by 922-1247)
590-0790
Compatibility
This cable can be used with the following drives:
• All 1.6” high 3.5” drives, including 160 MB IBM and
Seagate 400 MB
• Quantum ProDrive LPS 40 MB, 80 MB
Parts
Cable, SCSI Select, 400 MB HDA
28
922-1247
Compatibility
This cable can be used with the following drives:
• All 1.6” high 3.5” drives, including 160 MB IBM and
Seagate 400 MB
• Quantum ProDrive LPS 40 MB, 80 MB
Parts
Cable, SCSI Select
29
590-0238
Compatibility
This cable can be used with the following drives:
• All 1.6” high 3.5” drives, including 160 MB IBM and
Seagate 400 MB
• Quantum ProDrive LPS 40 MB, 80 MB
Parts
30
Cable, SCSI Select
922-1207
Compatibility
This cable can be used with the following drives:
• Conner FilePro 3, CFA Series
Parts
Cable, SCSI Select, Conner
31
922-1893
Parts
Cable, SCSI, Active Terminator
32
922-1185
Parts
Carrier, Hard Drive, Lower Bay
33
922-1124
Parts
Carrier, HDA, 3.5’’
34
922-1806
Parts
Carrier, Hard Drive (3.5 or 5.25)
35
805-5106
Parts
Carrier, Hard Drive, 3.5 SCSI, Internal~(Low Side, Mounting Holes)
36
805-0952
Parts
Carrier, Hard Drive, 3.5
37
922-0066
Parts
Carrier, Hard Drive, Internal, 3.5 SCSI~(High Side Mounting Holes)
38
805-5066
Parts
Carrier, Hard Drive/Tape Drive, 3.5’’
39
922-0621
Parts
CD/HD Connector, Adapter’
40
922-1820
Part number 922-1820 connects hard drives to the LC 500
series chassis/harness assembly.
Part number 922-1820 also connects the caddyless CD ROM
drive to the chassis/harness assembly of the LC 575.
Part number 922-1820 is not interchangeable with part
number 922-1821 used to connect the 300i CD ROM drive
to the LC 520 harness/chassis assembly.
Parts
Drive Carrier, HDA, 3.5 SCSI, Int.
41
805-0950
Parts
Drive Carrier, HDA, 3.5 SCSI, Internal
42
805-0980
Parts
Drive Carrier, HDA, 3.5 SCSI, Internal
43
805-5078
Parts
Drive Carrier, HDA, Internal, 5.25 SCSI
44
805-5051
Parts
Drive Mount, Macintosh II/IIx/IIfx
45
805-5062
Parts
Drive Mount, Macintosh IIcx/IIci
46
815-6030
Parts
EPROM (Model MB)
47
927-0002
Parts
EPROM, 40/80 MB HDA, Version TA.2 01
48
341-0768
Parts
Facilitation Warranty Reimbursement, Per Repair
49
011-0083
Parts
50
Hard Drive, 1 GB, IDE, 3.5"
661-0955
T
Parts
Hard Drive, 1 GB, SCSI, 3.5"
51
661-0228
This drive is one of the recommended replacement choices for
an out-of-warranty hard drive that’s been discontinued.
This drive may not be exchanged for the failed, out-ofwarranty drive, but must be ordered as stock.
All replacement drives will be shipped without carriers.
Return the defective drive without cables, carrier, hard
drive frame, LED cable, or SCSI select cable. Special
Packaging Requirements: Pkg: #602-0282 Surcharge:
$150.00.
Failure to comply with these requirements may result in a
packaging noncompliance surcharge. The drive warranty will
be void and Apple will return the module to the service
provider without repair if the drive bar code label,
manufacturer identification label, Apple capacity or EPROM
Parts
52
label, or labels that say “Warranty Void if Seal Broken”
have been tampered with or removed.
Parts
53
Hard Drive, 1.1 GB, IDE, 2.5"
661-0944
The hard drive ships without a carrier.
When present, the following must be removed before
returning the drive to Apple: frame, LED cable, SCSI select
cable.
WARRANTY: The drive warranty will be void and Apple will
return the module to the service provider without repair if
the drive bar code label, manufacturer identification label,
Apple capacity and EPROM label, or labels that say
“Warranty Void If Seal Is Broken” have been tampered with
or removed.
For maximum compatibility, Apple recommends this drive
for use in older Macintosh computers and external drives
that support 2.5" IDE drives.
Parts
54
APPLE REQUIRES SPECIAL PACKAGING: failure to comply
with these requirements may result in a packaging
noncompliance charge. For more information, select the
notes icon in the Illustrated Parts chapter of the Hard
Drives manual.
Parts
55
Hard Drive, 1.2 GB, IDE, 3.5"
661-1106
When present, the following must be removed before
returning the drive to Apple: frame, LED cable, SCSI select
cable.
WARRANTY: The drive warranty will be void and Apple will
return the module to the service provider without repair if
the drive bar code label, manufacturer identification label,
Apple capacity or EPROM label, or labels that say “Warranty
Void If Seal Is Broken” have been tampered with or removed.
APPLE REQUIRES SPECIAL PACKAGING; failure to comply
with these requirements may result in a packaging
noncompliance charge.
Conner Drive Model # CFS1275A
Quantum Drive Model # 1.2GB FRBLA
Parts
56
Seagate Drive model # ST31276A
Quantum Drive Model # 1.2GB FBTMA
Parts
Hard Drive, 1.2 GB, IDE, 3.5"
57
661-1139
When present, the following must be removed before
returning the drive to
Apple: frame, LED cable, SCSI select cable.
WARRANTY: The drive warranty will be void and Apple will
return the module to the service provider without repair if
the drive bar code label, manufacturer identification label,
Apple capacity or EPROM label, or labels that say “Warranty
Void If Seal Is Broken” have been tampered with or removed.
The IDE drive is distinguished from a SCSI drive by the third
(alternate power) connector built into the connector bar on
the PCB.
APPLE REQUIRES SPECIAL PACKAGING; failure to comply
with these requirements may result in a packaging
Parts
58
noncompliance charge.
Conner Drive Model # CFS1275A
Quantum Drive Model # 1.2GB FRBLA
Seagate Drive model # ST31276A
Quantum Drive Model # 1.2GB FBTMA
Parts
Hard Drive, 1.2 GB, SCSI, 3.5"
59
661-1142
Warranty: The drive warranty will be void and Apple will
return the module to the service provider without repair if
the drive bar code label, manufacturer identification label,
Apple capacity and EPROM label, or labels that say
“Warranty Void if Seal is Broken” have been tampered with
or removed.
APPLE REQUIRES SPECIAL PACKAGING; failure to comply
with these requirements may result in a packaging
noncompliance charge. When present, the following must be
removed before returning the drive to Apple: Frame, LED
cable, SCSI select cable.
Parts
60
Hard Drive, 120 MB, SCSI, 2.5" (Discontinued)
661-0772
This part has been discontinued. For replacement of parts
covered under warranty or AppleCare, order 661-1752. For
replacement of out-of-warranty parts, refer to the list of
available hard drives in this manual.
Carrier Return Requirements:
Return the defective drive without a carrier.
Cable Return Requirements:
Return the defective drive without cables.
Special Packaging is Required.
Pkg: 602-0307; Surcharge: $150.00
Failure to comply with these requirements may result in a
packaging noncompliance charge. Refer to Service Prices for
ordering and pricing information.
Parts
61
Hard Drive, 120 MB, SCSI, 3.5 (Discontinued)
661-0021
This part has been discontinued. For replacement of parts
covered under warranty or AppleCare®, order 661-1750.
For replacement of out-of-warranty parts, refer to the
parts list in the Service Source manual for the product you
are repairing.
Parts
62
Hard Drive, 160 MB, SCSI, 2.5" (Discontinued)
661-0213
This part has been discontinued. For replacement of parts
covered under warranty or AppleCare, order 661-1752. For
replacement of out-of-warranty parts, refer to the list of
available hard drives in this manual.
You may require a new mounting bracket if you are replacing
a 661-0213.
Cable and Carrier Return Requirements
Return the defective drive without a carrier or cables.
Special Packaging Requirements
Pkg: 602-0307; Surcharge: $150.00
Failure to comply with these requirements may result in a
packaging noncompliance charge. Refer to Service Prices for
ordering and pricing information.
Parts
63
Hard Drive, 160 MB, SCSI, 3.5" (Discontinued)661-0214
This part has been discontinued. For replacement of parts
covered under warranty or AppleCare®, order 661-1750.
For replacement of out-of-warranty parts, refer to the
parts list in the Service Source manual for the product you
are repairing.
Parts
64
Hard Drive, 160 MB, SCSI, 3.5" (Discontinued)
661-1649
This part has been discontinued. For replacement of parts
covered under warranty or AppleCare®, order 661-1750.
For replacement of out-of-warranty parts, refer to the
parts list in the Service Source manual for the product you
are repairing.
Parts
65
Hard Drive, 160 MB, SCSI, 3.5" w/A/UX v2.0.1 (Discontinued)
661-1639
This part has been discontinued. For replacement of a hard
drive covered under warranty or AppleCare®, order 6611750. For replacement of out-of-warranty hard drives,
refer to the parts list in the Service Source manual for the
product being repaired. In either case, you must also order
the A/UX 2.0.1 Install CD (600-4193) to configure the
replacement drive, as it will not come preconfigured.
Note: All replacement drives will be shipped without
carriers.
Cable Return Requirements: Return the defective drive
without cables.
Carrier Return Requirements: Return the defective drive
without a carrier.
Parts
66
Special Packaging Requirements. Pkg: #602-0282. Surcharge: $150.00.
Failure to comply with these requirements may result in a
packaging noncompliance surcharge. Please refer to Service
Prices for ordering and pricing information.
The drive warranty will be void and Apple will return the
module to the service provider without repair if the drive
bar code label, manufacturer identification label, Apple
capacity and EPROM label, or labels that say “Warranty Void
If Seal Is Broken” have been tampered with or removed.
Parts
67
Hard Drive, 2 GB, Fast/Wide SCSI, 3.5’’, IBM661-0956
Return the defective hard drive without the SCSI cables,
SCSI select cable, LED cable, power cable, and the drive
carrier.
Warranty: The drive warranty will be void and Apple will
return the module to the service provider without repair if
the drive bar code label, manufacturer identification label,
Apple capacity or EPROM label, or labels that say “Warranty Void if Seal Broken” have been tampered with or
removed. APPLE REQUIRES SPECIAL PACKAGING; failure to
comply with these requirements may result in a packaging
noncompliance charge.
This drive uses SCSI ID cable, Type 1, P/N 922-2102.
Parts
Hard Drive, 2 GB, SCSI, 3.5’’
68
661-0180
This drive should only be exchanged “like-for-like.” This
drive is NOT interchangeable with part number 661-0892
(HDA, 2 GB, 3.5’’ SCSI, Unhoused).
Return the hard drive without the HDA frame, LED cable, and
SCSI select cable. Warranty: The drive warranty will be void
and Apple will return the module to the service provider
without repair if the drive bar code label, manufacturer
identification label, Apple capacity or EPROM label, or labels
that say “Warranty Void if Seal Broken” have been tampered
with or removed. APPLE REQUIRES SPECIAL PACKAGING;
failure to comply with these requirements may result in a
packaging noncompliance charge.
Parts
Hard Drive, 2 GB, SCSI, 3.5’’
69
661-0892
This drive should be exchanged only “like-for-like” and is
NOT interchangeable with part number 661-0180 (Hard
drive, 2 GB, SCSI, 3.5’’, Unhoused). WARRANTY: The drive
warranty will be void and Apple will return the module to the
service provider without repair if the drive bar code label,
manufacturer identification label, Apple capacity and EPROM
label, or labels that say “Warranty Void If Seal Is Broken”
have been tampered with or removed.
When present, the following must be removed before
returning the drive to Apple: frame, LED cable, SCSI select
cable. APPLE REQUIRES SPECIAL PACKAGING: failure to
comply with these requirements may result in a packaging
noncompliance charge.
Parts
Hard Drive, 2 GB, SCSI, 3.5’’
70
661-1076
This drive should only be exchanged “like-for-like.” This
drive is NOT interchangeable with part number 661-0180.
Return the hard drive without the HDA frame, LED cable, and
SCSI select cable. Warranty: The drive warranty will be void
and Apple will return the module to the service provider
without repair if the drive bar code label, manufacturer
identification label, Apple capacity or EPROM label, or labels
that say “Warranty Void if Seal Broken” have been tampered
with or removed. APPLE REQUIRES SPECIAL PACKAGING;
failure to comply with these requirements may result in a
packaging noncompliance charge.
Parts
Hard Drive, 200 MB, SCSI, 2.5’’
71
661-0779
When present, the following must be removed before
returning the drive to Apple: frame, LED cable, SCSI select
cable.
WARRANTY: The drive warranty will be void and Apple will
return the module to the service provider without repair if
the drive bar code label, manufacturer identification label,
Apple capacity and EPROM label, or labels that say
“Warranty Void If Seal Is Broken” have been tampered with
or removed.
For maximum compatibility, Apple recommends this drive
for use in older Macintosh computers and external drives
that support 2.5" SCSI drives.
APPLE REQUIRES SPECIAL PACKAGING: failure to comply
Parts
with these requirements may result in a packaging noncompliance charge.
72
Parts
73
Hard Drive, 230 MB, SCSI, 3.5" (Discontinued)661-1637
This part has been discontinued. For replacement of parts
covered under warranty or AppleCare®, order 661-1750.
For replacement of out-of-warranty parts, refer to the
parts list in the Service Source manual for the product you
are repairing.
Parts
74
Hard Drive, 240 MB, SCSI, 2.5’’
661-0217
Note: All replacement drives will be shipped without
carriers.
Compatibility
This drive can be used in the following:
•PowerBook Duo 210, 230, 250, 270c, 280, 280c
•PowerBook 520, 520c, 540, 540c
Cable Return Requirements
Return the defective drive without cables.
Carrier Return Requirements
Return the defective drive without a carrier.
Special Packaging Requirements
Pkg: 602-0307
Parts
75
Surcharge: $150.00
Failure to comply with these requirements may result in a packaging noncompliance charge.
Refer to Service Prices for ordering and pricing information.
Parts
76
Hard Drive, 240 MB, SCSI, 2.5’’661-0191
Parts
Hard Drive, 250 MB, IDE, 3.5"
77
661-0070
WARRANTY: The drive warranty will be void and Apple will
return the module to the service provider without repair if
the drive bar code label, manufacturer identification label,
Apple capacity or EPROM label, or labels that say “Warranty
Void If Seal Is Broken” have been tampered with or removed.
APPLE REQUIRES SPECIAL PACKAGING; failure to comply
with these requirements may result in a packaging
noncompliance charge.
Parts
Hard Drive, 250 MB, SCSI, 3.5"
78
661-0890
This drive is one of the recommended replacement choices for
an out-of-warranty hard drive that’s been discontinued.
This drive may not be exchanged for the failed, out-ofwarranty drive, but must be ordered as stock.
Parts
Hard Drive, 320 MB, SCSI, 2.5’’
79
661-0896
When present, the following must be removed before
returning the drive to Apple: frame, LED cable, SCSI select
cable.
WARRANTY: The drive warranty will be void and Apple will
return the module to the service provider without repair if
the drive bar code label, manufacturer identification label,
Apple capacity and EPROM label, or labels that say
“Warranty Void If Seal Is Broken” have been tampered with
or removed.
For maximum compatibility, Apple recommends this drive
for use in older Macintosh computers and external drives
that support 2.5" SCSI drives.
APPLE REQUIRES SPECIAL PACKAGING: failure to comply
Parts
with these requirements may result in a packaging noncompliance charge.
80
Parts
81
Hard Drive, 320 MB, SCSI, 3.5’’ (replaced by 661-0182)6610505
Cable Return Requirements:
Return the defective drive without cables.
Carrier Return Requirements:
Return the defective drive without a carrier.
Special Packaging Is Required.
Pkg: #602-1018
Surcharge: $150.00
Failure to comply with these requirements may result in a
packaging noncompliance surcharge. Please refer to Service
Prices for ordering and pricing information.
Parts
82
Hard Drive, 320 MB, SCSI, 2.5", In-Warranty Exchange ONLY
661-1753
Only order this part number when exchanging a failed hard
drive that meets both of the following conditions: 1) the
failed hard drive is covered under warranty or AppleCare®,
and 2) the like-for-like replacement hard drive has been
discontinued.
Apple has made every effort to maintain LED support in its
exchange program; however, some drives no longer support
an LED. We regret any inconvenience this may cause.
Parts
Hard Drive, 350 MB, IDE, 3.5"
83
661-0068
When present, the following must be removed before
returning the drive to Apple: frame, LED cable, SCSI select
cable.
WARRANTY: The drive warranty will be void and Apple will
return the module to the service provider without repair if
the drive bar code label, manufacturer identification label,
Apple capacity or EPROM label, or labels that say “Warranty
Void If Seal Is Broken” have been tampered with or removed.
APPLE REQUIRES SPECIAL PACKAGING; failure to comply
with these requirements may result in a packaging
noncompliance charge.
Parts
Hard Drive, 350 MB, SCSI, 3.5"
84
661-0182
This drive is one of the recommended replacement choices for
an out-of-warranty hard drive that’s been discontinued.
This drive may not be exchanged for the failed, out-ofwarranty drive, but must be ordered as stock.
Parts
85
Hard Drive, 4 GB, Fast/Wide SCSI, 3.5”
661-0958
Return the defective hard drive without the SCSI cables, SCSI
select cable, LED cable, power cable, and the drive carrier.
Warranty: The drive warranty will be void and Apple will
return the module to the service provider without repair if
the drive bar code label, manufacturer identification label,
Apple capacity or EPROM label, or labels that say “Warranty
Void if Seal Broken” have been tampered with or removed.
APPLE REQUIRES SPECIAL PACKAGING; failure to comply
with these requirements may result in a packaging
noncompliance charge.
This drive uses SCSI ID cable, Type 1, P/N 922-2102.
Parts
Hard Drive, 4 GB, SCSI, 3.5”
86
661-0951
When present, the following must be removed before
returning the drive to Apple: frame, LED cable, SCSI select
cable.
WARRANTY: The drive warranty will be void and Apple will
return the module to the service provider without repair if
the drive bar code label, manufacturer identification label,
Apple capacity or EPROM label, or labels that say “Warranty
Void If Seal Is Broken” have been tampered with or removed.
APPLE REQUIRES SPECIAL PACKAGING; failure to comply
with these requirements may result in a packaging
noncompliance charge.
Parts
87
Hard Drive, 40 MB, SCSI, 2.5", PB 100 (Discontinued)
661-1632
This part has been discontinued. For replacement of parts
covered under warranty or AppleCare, order 661-1752. For
replacement of out-of-warranty parts, refer to the list of
available hard drives in this manual.
The drive warranty will be void and Apple will return the
module to the service provider without repair if the drive
bar code label, manufacturer identification label, Apple
capacity and EPROM label, or labels that say “Warranty Void
If Seal Is Broken” have been tampered with or removed.
Carrier Return Requirements:
No carrier.
Special Packaging is Required.
Pkg: #602-0307
Parts
88
Surcharge: $150.00
Failure to comply with these requirements may result in a packaging noncompliance
surcharge. Please refer to Service Prices for ordering and
pricing information.
Parts
89
Hard Drive, 40 MB, SCSI, 2.5", PB 100 (Discontinued)661-1644
This part has been discontinued. For replacement of parts
covered under warranty or AppleCare, order 661-1752.
For replacement of out-of-warranty parts, refer to the list
of available hard drives in this manual.
The Conner 40 MB drive has a beveled edge on the left-hand
side.
The drive warranty will be void and Apple will return the
module to the service provider without repair if the drive
bar code label, manufacturer identification label, Apple
capacity and EPROM label, or labels that say “Warranty
Void If Seal Is Broken” have been tampered with or removed.
Cable Return Requirements:
Return the defective drive without cables.
Parts
90
Carrier Return Requirements:
Return the defective drive without a carrier.
Special Packaging is Required.
Pkg: #602-0307
Surcharge: $150.00
Failure to comply with these requirements may result in a
packaging noncompliance surcharge. Please refer to Service
Prices for ordering and pricing information.
Parts
91
Hard Drive, 40 MB, SCSI, 2.5" (Discontinued)661-0016
This part has been discontinued. For replacement of parts
covered under warranty or AppleCare, order 661-1752.
For replacement of out-of-warranty parts, refer to the list
of available hard drives in this manual.
Parts
92
Hard Drive, 40 MB, SCSI, 2.5" (Discontinued)
661-1630
This part has been discontinued. For replacement of parts
covered under warranty or AppleCare, order 661-1752. For
replacement of out-of-warranty parts, refer to other list of
available hard drives in this manual.
This drive contains a plastic “horse-shoe” shaped cover
located on the top of the drive.
The drive warranty will be void and Apple will return the
module to the service provider without repair if the drive
bar code label, manufacturer identification label, Apple
capacity and EPROM label, or labels that say “Warranty Void
If Seal Is Broken” have been tampered with or removed.
Cable Return Requirements:
Return the defective drive without cables.
Parts
93
Carrier Return Requirements:
Return the defective drive without a carrier.
Special Packaging is Required.
Pkg: #602-0307
Surcharge: $150.00
Failure to comply with these requirements may result in a
packaging noncompliance surcharge. Please refer to Service
Prices for ordering and pricing information.
Parts
94
Hard Drive, 40 MB, SCSI, 3.5’’661-0216
Upon failure all 20 MB drives will be upgraded to 40 MB
drives. If you send in a 20 MB drive, you will receive a 40
MB replacement drive.
Note: All replacement drives will be shipped without
carriers.
Compatibility
This drive can be used in the following:
•Macintosh SE, SE/30
•Macintosh II, IIcx, IIci, IIx, IIfx
•Macintosh IIsi
•Classic, Classic II
•Color Classic, Color Classic II
•LC, LC II, LC III
•Performa 400
Parts
95
Cable Return Requirements
Return the defective drive without cables.
Carrier Return Requirements
Return the drive without a carrier.
Special Packaging Requirements
Pkg: #602-0282
Surcharge: $150.00
Failure to comply with these requirements may result in a
packaging noncompliance surcharge. Please refer to Service
Prices for ordering and pricing information.
Parts
96
Hard Drive, 400 MB, SCSI, 3.5 ‘’ (replaced by 661-02196611636
When present, the following must be removed before
returning the drive to Apple: frame, LED cable, SCSI select
cable.
WARRANTY: The drive warranty will be void and Apple will
return the module to the service provider without repair if
the drive bar code label, manufacturer identification label,
Apple capacity and EPROM label, or labels that say
“Warranty Void If Seal Is Broken” have been tampered with
or removed.
APPLE REQUIRES SPECIAL PACKAGING: failure to comply
with these requirements may result in a packaging
noncompliance charge. When present, the following must be
removed before returning the drive to
Parts
Apple: frame, LED cable, SCSI select cable.
97
Parts
98
Hard Drive, 500 MB, IDE, 2.5 ‘’
661-1058
When present, the following must be removed before
returning the drive to Apple: frame, and LED cable.
This drive may or may not have an Apple logo on it.
WARRANTY: The drive warranty will be void and Apple will
return the module to the service provider without repair if
the drive bar code label, manufacturer identification label,
Apple capacity and EPROM label, or labels that say
“Warranty Void If Seal Is Broken” have been tampered with
or removed.
For maximum compatibility, Apple recommends this drive
for use in older Macintosh computers and external drives
that support 2.5" IDE drives.
Parts
99
APPLE REQUIRES SPECIAL PACKAGING: failure to comply
with these requirements may result in a packaging
noncompliance charge.
Parts
Hard Drive, 500 MB, IDE, 2.5 ‘’
100
661-0047
When present, the following must be removed before
returning the drive to Apple: frame, LED cable, SCSI select
cable.
WARRANTY: The drive warranty will be void and Apple will
return the module to the service provider without repair if
the drive bar code label, manufacturer identification label,
Apple capacity and EPROM label, or labels that say
“Warranty Void If Seal Is Broken” have been tampered with
or removed.
For maximum compatibility, Apple recommends this drive
for use in older Macintosh computers and external drives
that support 2.5" IDE drives.
APPLE REQUIRES SPECIAL PACKAGING: failure to comply
Parts
101
with these requirements may result in a packaging
noncompliance charge. For more information, select the
notes icon in the Illustrated Parts chapter of the Hard
Drives manual.
Parts
102
Hard Drive, 500 MB, IDE, 2.5", In-Warranty Exchange ONLY
661-1751
Only order this part number when exchanging a failed hard
drive that meets both of the following conditions: 1) the
failed hard drive is covered under warranty or AppleCare®,
and 2) the like-for-like replacement hard drive has been
discontinued.
Apple has made every effort to maintain LED support in its
exchange program; however, some drives no longer support
an LED. We regret any inconvenience this may cause.
Parts
Hard Drive, 500 MB, SCSI, 2.5 ‘’
103
661-0175
When present, the following must be removed before
returning the drive to Apple: frame, LED cable, SCSI select
cable.
WARRANTY: The drive warranty will be void and Apple will
return the module to the service provider without repair if
the drive bar code label, manufacturer identification label,
Apple capacity or EPROM label, or labels that say “Warranty
Void If Seal Is Broken” have been tampered with or removed.
For maximum compatibility, Apple recommends this drive
for use in older Macintosh computers and external drives
that support 2.5" SCSI drives.
APPLE REQUIRES SPECIAL PACKAGING; failure to comply
with these requirements may result in a packaging
Parts
104
noncompliance charge.
Parts
105
Hard Drive, 500 MB, SCSI, 2.5", In-Warranty Exchange ONLY
(Discontinued)
661-1752
Failed 500 MB drives may be exchanged using 661-0175.
Parts
Hard Drive, 500 MB, IDE, 3.5"
106
661-0146
When present, the following must be removed before
returning the drive to Apple: frame, LED cable, SCSI select
cable.
WARRANTY: The drive warranty will be void and Apple will
return the module to the service provider without repair if
the drive bar code label, manufacturer identification label,
Apple capacity and EPROM label, or labels that say
“Warranty Void If Seal Is Broken” have been tampered with
or removed.
APPLE REQUIRES SPECIAL PACKAGING: failure to comply
with these requirements may result in a packaging
noncompliance charge.
Parts
Hard Drive, 500 MB, IDE, 3.5" (replaced by 661-0146)
107
661-0086
Parts
Hard Drive, 500 MB, SCSI, 3.5"
108
661-0219
This drive is one of the recommended replacement choices for
an out-of-warranty hard drive that’s been discontinued.
This drive may not be exchanged for the failed, out-ofwarranty drive, but must be ordered as stock. All
replacement drives will be shipped without carriers.
Cable Return Requirements: Return the defective drive
without cables.
Carrier Return Requirements: Return the drive without a
carrier.
Special Packaging Requirements: Pkg: #602-0282
Surcharge: $150.00
Failure to comply with these requirements may result in a
packaging noncompliance surcharge. Please refer to Service
Price Pages for ordering and pricing information.
Parts
Hard Drive, 500 MB, SCSI, 3.5"
109
661-0974
This drive is one of the recommended replacement choices for
an out-of-warranty hard drive that’s been discontinued.
This drive may not be exchanged for the failed, out-ofwarranty drive, but must be ordered as stock.
Parts
110
Hard Drive, 500 MB, SCSI, 3.5", In-Warranty Exchange Only
661-1750
Only order this part number when exchanging a failed hard
drive that meets both of the following conditions: 1) the
failed hard drive is covered under warranty or AppleCare®,
and 2) the like-for-like replacement hard drive has been
discontinued.
Apple has made every effort to maintain LED support in its
exchange program; however, some drives no longer support
an LED. We regret any inconvenience this may cause.
Parts
Hard Drive, 700 MB, IDE, 3.5’’
111
661-0069
Parts
Hard Drive, 700 MB, SCSI, 3.5’’
112
661-0184
When present, the following must be removed before
returning the drive to Apple: frame, LED cable, SCSI select
cable.
WARRANTY: The drive warranty will be void and Apple will
return the module to the service provider without repair if
the drive bar code label, manufacturer identification label,
Apple capacity and EPROM label, or labels that say
“Warranty Void If Seal Is Broken” have been tampered with
or removed.
APPLE REQUIRES SPECIAL PACKAGING: failure to comply
with these requirements may result in a packaging
noncompliance charge.
Parts
Hard Drive, 750 MB, IDE, 2.5’’
113
661-0957
WARRANTY: The drive warranty will be void and Apple will
return the module to the service provider without repair if
the drive bar code label, manufacturer identification label,
Apple capacity or EPROM label, or labels that say “Warranty
Void If Seal Is Broken” have been tampered with or removed.
For maximum compatibility, Apple recommends this drive
for use in older Macintosh computers and external drives
which support 2.5" IDE.
APPLE REQUIRES SPECIAL PACKAGING; failure to comply
with these requirements may result in a packaging
noncompliance charge. For more information, select the notes
icon in the Illustrated Parts chapter of the Hard Drives
manual.
W
Parts
Hard Drive, 750 MB, SCSI, 2.5’’
114
661-0943
When present, the following must be removed before
returning the drive to Apple: frame, LED cable, SCSI select
cable.
WARRANTY: The drive warranty will be void and Apple will
return the module to the service provider without repair if
the drive bar code label, manufacturer identification label,
Apple capacity and EPROM label, or labels that say
“Warranty Void If Seal Is Broken” have been tampered with
or removed.
APPLE REQUIRES SPECIAL PACKAGING: failure to comply
with these requirements may result in a packaging
noncompliance charge. For more information, select the notes
icon in the Illustrated Parts chapter of the Hard Drives
manual.
Parts
115
Hard Drive, 80 MB, SCSI, 2.5" (Discontinued)
661-0211
This part has been discontinued. For replacement of parts
covered under warranty or AppleCare, order 661-1752. For
replacement of out-of-warranty parts, refer to the list of
available hard drives in this manual.
Note: All replacement drives will be shipped without
carriers
Cable Return Requirements
Return the defective drive without cables.
Carrier Return Requirements
Return the defective drive without a carrier.
Special Packaging Requirements
Pkg: 602-0307
Parts
116
Surcharge: $150.00
Failure to comply with these requirements may result in a
packaging noncompliance charge. Refer to Service Prices
for ordering and pricing information.
Parts
117
Hard Drive, 80 MB, SCSI, 3.5" (Discontinued)
661-0111
This part has been discontinued. For replacement of parts
covered under warranty or AppleCare®, order 661-1750.
For replacement of out-of-warranty parts, refer to the
parts list in the Service Source manual for the product you
are repairing.
Parts
118
Hard Drive, 80 MB, SCSI, 3.5" (Discontinued)
661-0212
This part has been discontinued. For replacement of parts
covered under warranty or AppleCare®, order 661-1750.
For replacement of out-of-warranty parts, refer to the
parts list in the Service Source manual for the product you
are repairing.
Parts
Hard Drive, 800 MB, IDE, 3.5"
119
661-0999
WARRANTY: The drive warranty will be void and Apple will
return the module to the service provider without repair if
the drive bar code label, manufacturer identification label,
Apple capacity or EPROM label, or labels that say “Warranty
Void If Seal Is Broken” have been tampered with or removed.
APPLE REQUIRES SPECIAL PACKAGING; failure to comply
with these requirements may result in a packaging
noncompliance charge.
Parts
Hard Drive, 800 MB, SCSI, 3.5"
120
661-1102
This drive is one of the recommended replacement choices for
an out-of-warranty hard drive that’s been discontinued.
This drive may not be exchanged for the failed, out-ofwarranty drive, but must be ordered as stock.
Parts
121
Hard Drive, 80 MB, SCSI, 3.5", A/UX v.2.0 (Discontinued)
661-0613
This part has been discontinued. For replacement of a hard
drive covered under warranty or AppleCare®, order 6611750. For replacement of out-of-warranty hard drives,
refer to the parts list in the Service Source manual for the
product being repaired. In either case, you must also order
the A/UX 2.0 Install CD (600-4192) to configure the
replacement drive, as it will not come preconfigured.
Note: All replacement drives will be shipped without
carriers.
Cable Return Requirements: Return the defective drive
without cables.
Carrier Return Requirements: Return the defective drive
without a carrier.
Parts
122
Special Packaging Requirements: Pkg: #602-0282.
Surcharge: $150.00
Failure to comply with these requirements may result in a
packaging noncompliance surcharge. Please refer to Service
Prices for ordering and pricing information.
Parts
HDA 160 Adjustment for RFI Tape
123
011-0073
Parts
Jumper, SCSI ID for HDA, (10 pack)
124
517-0546
Parts
Mounting Bracket, 40 MB HDA (Use with 661-1632)
125
922-0008
Parts
Mounting Bracket, 40 MB HDA (Use with 661-1632)
126
948-0002
Parts
Mounting Bracket, 40MB (Use with 661-1644)
127
948-0157
Parts
Screw, 6-32 x 3/16
128
408-1603
Parts
Screw, Hard Drive Bracket to Hard Drive, MacFet M3x.5x4
129
922-1682
Parts
Screw, Hard Drive, PB Duo, Pkg. of 10
130
922-1275
Parts
Screw, M3x0.5x4mm, Pkg. of 5
131
922-0012
Parts
SCSI-Device-to-Case Cable
132
590-0235
Parts
Switch, SCSI Select Assembly (Replaced by 922-1250)
133
705-0045
Parts
134
Switch, SCSI Select Assembly
922-1250
Compatibility
This switch can be used with the following cables:
• 922-1247
• 922-1248
• 922-1207
Parts
System Cable (CPU to SCSI Device)
135
658-8031