the Sig Mfg. 2012 Catalog Update - Treasure Coast RC Scale Boaters

CATALOG UPDATE
SIG FOUR-STAR 120 ARF
THE TRADITION CONTINUES ...BIGGER DOES FLY BETTER
The FOUR-STAR 120 ARF is an easy to fly, easy to assemble,
good-looking introduction to giant scale aircraft that is also an
ideal first low wing airplane. Its gentle handling will set the low
time flyer at ease but it is capable of satisfying the advanced flyer with its maneuverability and smooth handling. This is a sport model you will want to take to the field
every time. You will love the two-piece wing that makes storage and transport easy.
The FOUR-STAR 120 ARF has been engineered to get you into the air as quickly as
possible with an R/C model that will truly last. The balsa airframe has been expertly
built making extensive use of lite-ply for strength and covered with high quality polyester
film. Checkerboard film is used on the bottom of the wing and horizontal stabilizer
to make this model visible even at extreme distances. Includes virtually everything to
complete your model including engine mount, fuel tank, matching anodized aluminum
landing gear, factory-painted fiberglass wheel pants, wheels, deluxe tailwheel assembly,
SIG spinner, pushrods, linkages and decals. Assembly is super quick
using the detailed, fully illustrated assembly manual.
KEY FEATURES
„ Two Piece Wing For Easy Transport
„ Professionally Covered With High Quality Polyester Film
„ High Visibility Checker-Board Trim
„ Fiberglass Wheel Pants
„ Deluxe Tailwheel Assembly
„ IMAA Legal
„ Low Wing Loading Gives Outstanding Slow Speed Characteristics
„ Pull-Pull Rudder Linkage
Specifications:
Wing Span:
81 in. (2057 mm)
Wing Area:
1205 in² (77.7 dm²)
Length:
65 in. (1651 mm)
Flying Weight:
11.5 - 12 lbs. (5220 - 5440 g)
Radio Required:
4 Channel w/5 servos
(rudder servo 80 oz./in. minimum and 1200 mAh receiver battery required)
Engine:
.90 - 1.20 in³ (15 - 20 cm³) 2-Stroke
1.20 - 1.50 in³ (20 - 26 cm³) 4-Stroke
Four-Star 120 ARF, Red
Four-Star 120 ARF, Yellow
www.sigmfg.com
Order No. SIGRC65ARFR
Order No. SIGRC65ARFY
1
P-51B MUSTANG ARF
Prior to production of the P-51B, fighter escorts such as
the P-47 did not have the required range and had to turn back, leaving the bombers to
make their bombing runs with no fighter protection. North American Aviation went to work delivering the first P-51 prototype in just 102
days and it was a remarkable step forward in fighter performance. The P-51B could climb to 20,000 feet in under 6 minutes and fly 440
mph at altitude – faster than any other fighter plane at the time. Most importantly, it was the range of 1080 miles (a whopping 2600 mile
range with drop tanks), which enabled the P-51B to escort the bombers all the way to Berlin.
The SIG P-51B Mustang ARF is modeled after the famous “Shangri-La” which was so effective in combat that Gen. Eisenhower once
remarked to pilot Don Gentile, “You are a one man air force!” The SIG P-51B is loaded – flaps, retracts, complete “Shangri-La” decal set,
painted fiberglass cowl, molded canopy, spinner, wheels, engine mount, fuel tank and detailed illustrated assembly manual. The model is
hand built from balsa and plywood and expertly covered with high quality polyester film.
As you would expect from SIG, this is a show-stopper – a scale ARF model that others will land their planes to watch fly. The real fun
comes when you suck up the landing gear. This is what the Mustang was born to do, race across the ground at a full gallop. Yet, when
you lower the flaps and landing gear, the model slows to an easy, predictable touchdown. Controls: rudder, elevator, ailerons, flaps,
retracts, throttle.
Order No.
SIGRC103ARF
Specifications:
Wing Span:
Wing Area:
Length (incl. spinner):
Flying Weight:
Wing Loading:
Scale of Model:
Engine:
Radio:
66.9 in. (1700 mm)
770 in.² (49.67 dm²)
55.9 in. (1420 mm)
8.0 - 8.5 lbs. (3.63 - 3.86 kg)
23.9 - 25.4 oz./ft.² (73.1 - 77.6 g/dm²)
approx. 1/6.6
.90 - 1.00 in.³ (15 - 16.4 cm³)
2-Stroke or 4-Stroke Glow Engine
6-channel radio system, 8 servos*
*7 standard servos and 1 retract servo
P-51B includes the pictured Mustang Retract set.
SIG P-51B MUSTANG RETRACT
Mechanical retract set included with the P-51B
Order No. SIGRPSH885
An ARF Electric-Powered Edition Of A Classic R/C Trainer & Sport Model
Since its introduction in 1987, the KADET SENIORITA has been built and flown
by literally tens of thousands of beginning R/C pilots, helping them to earn their
"R/C wings". The designer, R/C pioneer Claude McCullough, knew that the key
to learning how to fly an R/C model was being able to slow the model down to
allow the pilot time to think about their next control input. That concept is still
true today and makes this new KADET SENIORITA EP ARF a perfect choice for
your first R/C airplane.
This KADET SENIORITA EP ARF is made for electric power! It’s almost as if
Claude McCullough had electric power in mind when he designed the first
SENIORITA - light and strong, little has been changed from the original kit
design, except for the motor mounting and cowl, and the addition of ailerons!
With a modern brushless motor and li-po batteries, you will enjoy 15+ minute
flights, ranging from incredibly slow flight for the beginner to enough aerobatic
performance to satisfy an experienced R/C pilot. From your first solo flight to
beyond, the KADET SENIORITA EP ARF can teach you touch and go landings,
loops, rolls, inverted flight and more, all easily and gracefully performed.
The KADET SENIORITA EP ARF is not constructed like your typical ARF! This
airplane is handcrafted using the timeless balsa stick and sheet structures that
previously you could only get by building it yourself. It's professionally covered
in transparent red covering with black and silver trim. Other features include a
pre-installed molded windshield and side windows, excellent hardware, wheels,
spinner, decals, and a complete step-by-step fully illustrated assembly manual.
Controls: rudder, elevator, ailerons, motor
Order No.: SIGRC60ARF
Specifications:
Wing Span:
Wing Area:
Length:
Flying Weight:
Wing Loading:
63 in.
750 sq. in.
52 in.
74 oz.
14.2 oz./sq. ft.
Includes pre-installed molded plastic windsheild
and side windows, plus molded plastic cowling with
matching spinner
Large tail surfaces and light weight construction give
the Kadet Seniorita EP ARF legendary stability at low
flight speeds
Items Needed To Complete
Kadet Seniorita EP ARF:
(1600 mm)
(48.4 sq. dm)
(1320 mm)
(2097 g)
(43.3 g/sq. dm)
SIG Manufacturing Company, Inc.
Motor:
400 Watt Brushless Outrunner
(such as Himax™ HC3522-0990)
Battery: 3-Cell 3300 mAh Lithium Polymer
(such as Order No. RCSSAF07023)
ESC:
45A (minimum)
Radio: 4-Channel with 4 Standard Servos
(2) 12 inch long servo extensions
(1) standard Y-harness chord
P.O. Box 520 • 401-7 South Front Street
Montezuma, Iowa 50171-0520 USA
Phone: (641)623-5154 • Fax: (641)623-3922
Website: www.sigmfg.com • E-Mail: [email protected]
The Kadet Seniorita EP ARF features a removable
2-piece bolt-on wing with a strong aluminum joiner.
Easy to transport!
Order No. SIGRC106
SIG FOUR-STAR 20 EP KIT
Building on the 20-year reputation of the original Four-Star line of great sport airplanes, we bring you this highly requested version
designed for electric power. Like it’s older siblings it retains the easy and relaxed flying characteristics of the Four-Stars. Open the
throttle and increase the control throws and it will do about any wild maneuver your thumbs can dream up. Add to this the portability of a smaller size and the quietness and convenience of electric power and you have another winner for sport flying. While
designed for electric power it is configured to easily convert to glow engine power in the .15 to .25-engine range so you have the
best of both worlds.
Specifications:
Wing Span:
Wing Area:
Length:
Flying Weight with
250-watt motor and
3s1p 2200 mAh lipo:
Wing Loading:
Radio Required:
Power Required:
Prop:
48 in. (1219 mm)
430 in² (27.7 dm²)
38 in. (965 mm)
2-1/2 lbs. (1130 g)
13.4 oz./sq. ft. (40.8 g/dm²)
4-Channel with 4 mini servos
250 to 350 watt electric motors
or .15 to .25 glow engines
9x6 APC ThinElectric
KEY FEATURES:
• Laser cut parts
• Full size plans
• Light weight balsa construction except for key parts
• Fast building wing
• Tab locked fuselage
• Photo illustrated instruction manual
• Durable aluminum landing gear
• Molded canopy
• Molded cowl
• SIG Easy Hinges
• Large decal sheet
• Pushrods
• Hardware pack
SIG FOUR-STAR 20 EP KIT Order No. SIGRC106
Order No. SIGRC106
imal friction,
For minimal
friction, only one end of the
shaft touches a magnet
Order No. SIGSH903
SIG Fan Balancer KIT
With today’s electric ducted fans spinning at over 30,000 rpm’s, having a balanced fan has never been more critical. At these high
rpm’s, a difference in just a few tenths of a gram can lead to excessive vibration and a reduction in thrust.
The SIG Fan Balancer is a precision, high-tech instrument capable of detecting the smallest out of balance situation. It all starts with
the shaft. The shaft on the Fan Balancer is made from high-speed steel (the same steel used for drill bits and machine tools) manufactured to a straightness of 1/1,000 mm and utilizing precision machine ground ends. Then the shaft is suspended between two powerful rare earth magnets. All that would make for a good fan balancer but at SIG, we went the extra step. We added an adjustment
screw so that you can precisely adjust the spacing so that only ONE end of the shaft is touching a magnet. This provides for the least
amount of possible friction.
Your electric ducted fan model airplane is a marvel of model engineering. Shouldn’t your fan balancer be just as sophisticated?
Also does a fantastic job of balancing small propellers.
SIG Fan Balancer KIT Order No. SIGSH903
SIG Surface Indicator Gauge S.I.G. KIT
You’ve finally finished your dream model. The center of gravity is right on,
the prop is balanced, and all the controls are hooked up and functioning
perfectly. But wait, what about the control throws? Every model airplane
KIT and ARF have a specified control surface travel for each control surface. Making sure that your model matches the designer’s specifications
will turn a twitchy, nerve-racking handful of a model into a pussycat.
Coming in on a dead-stick, final approach is not the time to find out that
you don’t have enough elevator control throw to keep the nose up!
The SIG Surface Indicator Gauge enables you to accurately measure and
set your control surface throws. It works either in a vertical direction for
rudders or in a horizontal direction for elevators, ailerons and flaps. The
control throws are easily measured, without the need of a third Hand, on
the laser-inscribed gauge in standard measurements on one side or metric
on the other side. Available in two sizes. The smaller size works on control surfaces up to 89 mm (3 1/2 in.) wide which are typically found on
planes up to about .60 size. The larger size is for control surfaces measuring up to 152 mm (6 in.), which includes models as large as 1/4 scale.
SIG S.I.G. KIT Small
SIG S.I.G. KIT Large
Order No. SIGSH901
Order No. SIGSH902
Order No. SIGSH901
SIG E-PRO-BOX KIT
The new SIG E-PRO-BOX has been especially designed for the hobbyist whose specialty is electric powered models. The E-PRO-BOX has
room for everything one would need out at the field for airplanes, boats, etc. All compartments and features are designed with the electric modeler in mind.
The E-PRO-BOX is equipped with an extra large battery compartment which can carry gel cells up to 36000 mAh for charging purposes
and/or for the optional SIG Battery Warming Box. Low outside temperatures rob LiPo batteries of their full power. To negate this affect,
SIG has developed an optional insulated, all metal battery warming box which will keep your charged LiPo batteries at their peak power.
So when the temperature dips at the flying field, the warming box will keep your LiPo’s at their full power. As in all our field box products, all parts are precision laser cut from 1/4” (6 mm) SIG plywood.
Features…
„Convenient space for chargers
„Large, adjustable cradle on top to hold airplanes, boats etc.
„Banana plugs included for easy access to the 12 volt battery(s)
„Sturdy carrying handle
„A covered compartment on top with a hinged lid
„Optional wheel kit with aluminum handle (Order No. SIGBX004B)
„Optional metal, electric warming box (Order No. SIGBX004A)
Designed by modelers for modelers
Top quality SIG design and customer support
SIG E-PRO-BOX KIT Order No. SIGBX004
Complete equipped
SIG E-PRO-BOX
SIG Universal Wheel Add-On
for Field Boxes
With 2x 12 V batteries and a full compliment
of tools, the E-PRO-BOX can get really heavy
in a hurry! So if you aren’t built like Arnold
Schwarzenegger or just want to save your
back, the optional SIG Wheel kit is what you
need. Simple installation, all hardware included
and you can easily roll your field box at the
flying field. Light weight aluminum handle is
removeable for transport. Can also be installed
on field boxes other then SIGBX004.
SIG Wheel Add-On Order No. SIGBX004B
SIG Battery Warming Box
Why do you need the new SIG Battery Warming Box? Because, you want to have your
batteries at the highest power level they can produce! The SIG Battery Warming Box is
made out of steel and is isolated with foam to hold the optimum LiPo temperature. The
box works with 12 VDC and is equipped with an electric thermostat that can be adjusted to the optimum temperature for your particular batteries. For example, for LiPo cells
this is approximately 38-40 °C (100 – 104°F). A small fan inside the box circulates the air
so that the temperature is kept evenly throughout the box. The thermostat automatically
cycles the warming element on and off to keep the load on the 12 V battery(s) as low as
possible. The SIG Battery Warming Box can be used either as a stand-alone device or in
perfect combination with the SIG E-PRO Field Box.
SIG Battery Warming Box Order No. SIGBX004A
SIG Battery Warming Box
SIG RASCAL EP-49
Almost Ready To Fly Brushless Electric Powered R/C Airplane
The all-new Rascal EP-49 ARF retains all the good looks of the original, but now the performance has been dramatically improved. Updated
with ailerons for more precise control and a new, more powerful brushless motor with brushless compatible ESC for great climb performance and duration.
The new brushless motor and ESC combination really provides a serious amount of power and duration, making the RASCAL EP-49 ARF
one very nice performing airplane! The Rascal is available in two colors, brilliant white and transparent red or brilliant white and transparent yellow. Controls: Rudder, Elevator, Ailerons and Motor.
ARF Features:
„Factory-Built All Wood Airframe
„Premium Iron-On Polyester Covering
„Available in two different, attractive color schemes
„Performance Matched Power System consisting of a
Brushless Outrunner Electric Motor, ESC, and Prop
„Complete high quality hardware
„Fully illustrated step-by-step assembly manual
Specifications:
Wingspan:
Wing Area:
Length:
Flying Weight:
Power:
Radio Required:
Battery Required:
Order No.
49 in. (1245 mm)
324 in.² (20.9 dm²)
32-1/2 in. (825.5 mm)
22 to 25 oz. (624 to 700 g)
Brushless Outrunner Electric Motor,
ESC & Propeller included
4-Channel with 4 micro servos
and micro receiver
3s1p 850-1300 mAh Li-Po
SIGRC107ARFR
SIGRC107ARFR (white & red)
SIGRC107ARFY (white & yellow)
AND
N
w
wi
th a
ailerons...
Now
with
Brushless Outrunner Motor
KAVAN Starter Adapter for R/C Cars
Precisely machined from aluminum and hardened steel. Works perfectly with KAVAN’s Planetary
Gear Starter (Order No. KAV0111). Available in two sizes: 6 mm and 8 mm hexagonal “ball”.
KAVAN Starter Adapter for R/C Cars, 6 mm Order No. KAV0118A
KAVAN Starter Adapter for R/C Cars, 8 mm Order No. KAV0118B
KAVAN
K
KAV
AV
AVAN
AN Sta
St
Starter
rte
terr Ad
A
Adapter
da
dap
apte
te
er fo
ffor
or R/C
R/
/C
C Car
Ca
Carss
SPECIFICATIONS:
Fly With Electric Or Glow Power!
The SIG KADET LT-40 EG is the latest ARF rendition of
America's favorite R/C trainer, now redesigned to
accommodate either electric or glow power. Like all SIG
KADETS, the LT-40 EG behaves perfectly in flight with
true "hands off" stability. It's large size and light wing
loading lets it fly slower than other trainers. Slower
speed gives the student pilot more time to think and
react to what the model is doing. That makes learning to
fly R/C quicker and easier!
This beautifully handcrafted airplane takes no shortcuts
in quality of materials or workmanship. No foam - this
is a traditional all-wood model airplane, which means
it's light, strong and durable! Expertly covered with
UltraCote® (aka ORACOVER®) premium polyester
covering material. The LT-40 EG ARF is engineered for
quick assembly with a minimal number of parts. A
photo illustrated assembly manual takes you easily
through each step. Quality hardware includes spinner,
wheels, pushrods, fuel tank, etc.
You won't find a better way to get started in R/C flying
than with the KADET LT-40 EG ARF.
Wing Span:
Wing Area:
Length:
Flying Weight:
Wing Loading:
Radio Req.:
Glow Power:
70 in.
(1778 mm)
900 sq. in.
(58.1 dm2)
57 in.
(1447 mm)
6 - 6.25 lbs.
(2720 - 2835 g)
15 - 16 oz./sq. ft. (47 - 49 g/dm2)
4-Channel with 4 Standard Servos
2-Stroke .40 - .46 cu. in. (6.5 - 7.5 cc)
4-Stroke .40 - .54 cu. in. (6.5 - 8.8 cc)
Electric Power: 500 watt (3528 - 1000kv) Brushless
Motor; 50 - 60A ESC; Lipo Battery Pack
ARF Order No.: SIGRC67EGARF
Kit Order No.: SIGRC67
For ELECTRIC POWER use a 500 watt Brushless
Outrunner Motor, 50 - 60A ESC, & Lipo Battery
Removable Hatch Allows Easy Access To The Battery
Pack (electric power) or Fuel Tank (glow power)
SPECIFICATIONS:
Wing Span:
Wing Area:
Length:
Flying Weight:
Wing Loading:
Radio Req.:
Glow Power:
80.5 in.
(2045 mm)
1180 sq. in.
(76.1 dm2)
64.75 in.
(1645 mm)
6 - 6.5 lbs.
(2720 - 2950 g)
11.7 - 12.7 oz./sq. ft. (36 - 39 g/dm2)
4-Channel with 5 Standard Servos
2-Stroke .40 - .46 cu. in. (6.5 - 7.5 cc)
4-Stroke .50 - .61 cu. in. (8.1 - 10 cc)
Electric Power: 500 watt (3528 - 1000kv) Brushless Motor;
50 - 60A ESC; Lipo Battery Pack
ARF Order No.: SIGRC58EGARFB - White/Trans. Blue
SIGRC58EGARFR - White/Trans. Red
Kit Order No.: SIGRC58
Fly With Electric Or Glow Power!
ELECTRIC POWER: 500 watt Brushless
Motor; 50 - 60A ESC; Lipo Battery
Removable Hatch Allows Easy Access To
Battery Compartment
2-Piece Wing For Easy Transport
Originally designed for training, tens of thousands of
newcomers have successfully learned to fly with a SIG
KADET SENIOR. Even experienced R/C pilots enjoy the
SIG KADET'S slow leisurely flight characteristics - doing
touch and go landings at the speed of a walk. The
KADET SENIOR is also a versatile workhorse - float
flying, banner or glider tow, airborne camera, parachute
drop, night flying with add-on lights, and just about
any other load carrying task is easy for the giant KADET
SENIOR. The huge 2-piece wing is IMAA legal at
80-1/2" span and provides massive lifting ability.
The KADET SENIOR EG ARF gets you in the air quickly. Each part is meticulously built using quality woods
and factory covered with premium UltraCote® (aka
ORACOVER®) transparent red or blue, which lets the
beautiful woodwork show through. The KADET
SENIOR EG ARF is 90% assembled and includes a
rugged fiberglass cowl, a complete hardware package
and fully illustrated, step-by-step assembly manual.
SPECIFICATIONS:
A GIANT VERSION OF A
CLASSIC DESIGN, NOW WITH FLAPS!
The legend of the SIG Rascal began with a small
rubber-powered free-flight model in the 1950s.
Adapted for modern radio control, the Rascal's classic
good looks and dream-come-true flying characteristics
have made it the favorite everyday airplane of
thousands of R/C pilots. With a wingspan of more
than 9 feet, the Rascal 110 ARF is one of the few giant
size models that you will be comfortable taking to the
field and flying every day.
The Rascal 110 ARF flies as good as it looks!
Streamlining and a high performance airfoil allow the
Rascal 110 ARF to do maneuvers better than typical
high wing designs. Slow rolls, point rolls, extended
inverted flight, Cuban 8s, are all part of the Rascal 110's
aerobatic routine. The light wing loading of the Rascal
110 ARF also makes it a versatile workhorse. Float
flying, banner or glider tow, onboard video or camera
work (several universities and the military are using
them), parachute drop, night flying with add-on lights,
and just about any other load carrying task is easy for
the giant RASCAL 110 ARF. Available in two color
schemes, the Rascal 110 ARF is meticulously covered
with premium UltraCote® (aka ORACOVER®) film.
Wing Span:
Wing Area:
Length:
Flying Weight:
Wing Loading:
Glow Power:
110 inches
(2794 mm)
1522 sq. inches (98.2 dm2)
75.75 inches
(1924 mm)
11 - 13 lbs.
(4990 - 5897 g)
17 - 20 oz./sq.ft. (51 - 60 g/dm2)
2-Stroke 1.2 - 1.5 cu. in.
(19.7 - 24.6 cc)
4-Stroke 1.2 - 1.8 cu. in.
(19.7 - 29.5 cc)
Gas Power:
1.2 - 1.5 cu.in.
(19.7 - 24.6 cc)
Electric Power: 1600 watt (6320 - 250kv) Brushless Motor;
80A ESC; Lipo Battery Pack
Radio Req.:
5-Channel with 7 Heavy-Duty Servos
Order No.:
SIGRC84ARFB - White/Trans. Blue
SIGRC84ARFR - White/Trans. Red
2-Piece Wing For Easy Transport
Operating Flaps On 5th Channel
SPECIFICATIONS:
Electric Powered Trainer!
w/Brushless Motor and Speed Control
The Kadet EP-42B ARF was conceived as the very
definition of an R/C electric trainer. In the air, the
Kadet EP-42B ARF has a large speed envelope, allowing
it to be flown as slowly as needed for beginning pilots.
Wind? The included RCS brushless motor is whisper
quiet and powerful, which is fully capable of flying the
Kadet EP-42B ARF smoothly through most any normal
wind conditions.
The SIG Kadet EP-42B ARF is truly a “quick build”!
Includes factory installed windows, a “quick change”
battery hatch, pre-wired, powerful RCS Simplex
brushless motor and 18 amp ESC, 8-1/2 x 8 propeller,
quality hardware, cowling, fully illustrated, step-by-step
assembly manual, and decals. Available in two color
schemes, the Kadet EP-42B ARF is meticulously covered
with premium UltraCote® (aka ORACOVER®) film.
Wing Span:
Wing Area:
Length:
Flying Weight:
Radio Req.:
Order No.:
42 in.
(1067 mm)
330 sq. in.
(21.3 dm2)
34 in.
(864 mm)
24 - 26 oz.
(680 - 737 g)
4-Channel, Micro Receiver,
4 Micro Servos
SIGRC104ARFB - White/Trans. Blue
SIGRC104ARFR - White/Trans. Red
Kit includes a powerful and easy to install RC
System Simplex 3D brushless motor and ESC.
Removable battery compartment hatch with
clever plastic latch mechanism built in.
SIG Mfg. Co., Inc.
401 South Front St • P O Box 520 • Montezuma, IA 50171-0520 • USA • Phone: (641) 623-5154 • Fax: (641) 623-3922
E-mail: [email protected] • Website: www.sigmfg.com
SIG Manufacturing
Combo Packages!
Popular SIG aircraft with an included Aviastar 2-stroke Glow Engine.
SIG LT-40 ARF with AVI .46 COMBO
Order No. SIGRC67EGARFC
SIG Four-Star 40 ARF, Red with AVI .46 COMBO
Order No. SIGRC44ARFRC
SIG Four-Star 40 ARF, Yellow with AVI .46 COMBO Order No. SIGRC44ARFYC
SIG MAYHEM 40 ARF with AVI .46 COMBO
Order No. SIGRC98ARFC
SIG RASCAL 40 ARF, Blue with AVI .46 COMBO Order No. SIGRC83ARFBC
SIG RASCAL 40 ARF, Red with AVI .46 COMBO Order No. SIGRC83ARFRC
Each Combo includes an .46 Aviastar Engine
SIG Wood Floats RTF
Pre-built and ready to use, the SIG Wood Floats RTF will quickly convert your landlocked model aircraft for water use. The floats
include twin water rudders, hardware and everything needed for mounting and control. The .40 Class Floats use a clever but
effective connection to drive the water rudders from the aircraft‘s rudder while the 1.20 class floats use a pull-pull water rudder
system. Built from lite-ply and balsa and pre-covered in SIG AeroKote® using a proven watertight seam overlap technique, the
floats are light, strong and perform beautifully. The .40 Class Floats are ideal for aircraft up to 7 lbs (3175 g) while the 1.20 Class
Floats are for larger aircraft up to 16 lbs (7257 g). Rascal 110 shown but not included.
Description
Float Length
Order No.
.40 Class Wood Floats RTF
1.20 Class Wood Floats RTF
42 in. (106.7 cm)
60 in. (152.4 cm)
SIGFK003ARF
SIGFK004ARF
Order No. SIGFK004ARF
Accessories
RC System SimTransmitter + FMS-Simulator
There are different ways to learn model flying. If an
experienced model flyer is not on site then the first steps
can be disappointing. At worst case you could crash your
first model. Especially for learning R/C helicopter flying
the so called „Dry Run“ on a simulator is an inexpensive
and suggested method. The SimTransmitter „Joystick“
in combination with the FMS Flightsimulator provides
the ideal virtual beginner airplane or helicopter „model“.
Simply plug the SimTransmitter into a free USB port and
configure it as a joystick. With the SimTransmitter you can
control almost all simulators on the market, not only the included FMS
Flightsimulator*.
System requirements: Windows 98 SE/Windows 2000/Windows XP; OpenGL/DirectX graphic board with min. 64 MB memory;
Min. 600 MHz Intel or AMD Processor and 256 MB memory.
*FMS Flightsimulator can also be downloaded for free on the Internet.
SimTransmitter (Throttle - Right) Mode 1
SimTransmitter (Throttle - Left) Mode 2
Order No. RCSRC39000B
Order No. RCSRC39000A
RC System Aluminum Case
If your model survived the flight, don‘t let it get damaged in transport!
- With the attractive aluminum case from RC System this will never
happen. It is the ideal storage for your MiniCopter or similar Helicopters
and of course other equipment such as your R/C transmitter. The aluminum case is fitted with plastic corner protectors, 2 locks and handgrip. The inner foam can be cut to fit your individual needs, providing
optimal protection for your sensitive equipment.
Measurements:
Inner (L x W x H): ca. 20.5 x 9.6 x 4.5 in.
Outer (L x W x H): ca. 21.2 x 10.6 x 6.7 in.
RC System Aluminum Case
Order No. RCSRC2079
Order No. RCSRC2079
Multiple PSH for greater Strength
Elevator Neutral
Elevator Down
KAVAN Precision Secret Horn - the invisible Control Horn!
Precision Secret Horn
Great accessory for scale model builders and experimenters! Precision Secret Horn is for the modeler who finds conventional,
externally mounted control horns and pushrods unattractive. The innovative Secret Horn is ”invisible“ since the control horn is
inside your airplane. Adjustable control throws; simply move the brass plate up or down the threaded steel internal control horn.
The bearing shaft of the hinge is steel. Strong enough for the torque from any Micro- or Mini-Servo, 25 g (1 oz). For larger servos
mount multiple Precision Secret Horns together for even greater strength (See Picture). Use to control ailerons, flaps, rudder or
elevator. Primarily intended for kits since installation in a prebuilt ARF airplane is difficult. Fully assembled, injection molded
plastic and steel construction. Includes instructions. Pushrod shown but not included. Package: Pair (1 left, 1 right)
KAVAN Precision Secret Horn (2)
Order No. KAV6382
RC System®
RC System FULLYMAX Li-Po Cells
RC SYSTEM developed a whole range of Li-Po batteries for the
R/C model industry. They are lighter and smaller than normal
Ni-MH cells. The Internal resistance is the lowest on the market, this ensures an excellent discharge voltage for a surplus
of power. From the multiple tests that have been carried out,
the safety is impeccable. Comes in a highly protective blister
packaging along with user instructions that should be read carefully. Each pack includes a balancing connector (RC System,
Graupner, Robbe etc. style).
For maximum performance, safety and Li-Po pack longevity
order the optional RC System FB-605 Li-Po SMART AUTO
BALANCER, Order No. RCSSA10126.
RC System High Power (HP) Series Li-Po
For 80% of R/C modeling the HP Series Li-Po packs provide
more than enough power. The conservative rating of
15C continuous and 30C burst will offer outstanding performance for most models.
Capacity
Voltage
Cells
Dimensions
LxWxH
Weight
Max Discharge
Continuous/Burst
Order No.
150 mAh
7.4 V
2S1P
1.37 x 0.74 x 0.27 in.
0.33 oz.
15 C (2.25A) / 30 C (4.5A)
RCSSAF07001
150 mAh
11.1 V
3S1P
1.37 x 0.74 x 0.43 in.
0.47 oz.
15 C (2.25A) / 30 C (4.5A)
RCSSAF07002
260 mAh
3.7 V
Single
2.08 x 1.22 x 0.12 in.
0.24 oz.
15 C (3.9A) / 30 C (7.8A)
RCSSAF07003
260 mAh
11.1 V
3S1P
2.08 x 1.22 x 0.43 in.
0.84 oz.
15 C (3.9A) / 30 C (7.8A)
RCSSAF07005
460 mAh
3.7 V
Single
1.89 x 1.18 x 0.16 in.
0.39 oz.
15 C (6.9A) / 30 C (13.8A)
RCSSAF07006
460 mAh
7.4 V
2S1P
1.89 x 1.18 x 0.35 in.
0.89 oz
15 C (6.9A) / 30 C (13.8A)
RCSSAF07007
460 mAh
11.1 V
3S1P
1.89 x 1.18 x 0.55 in.
1.27 oz.
15 C (6.9A) / 30 C (13.8A)
RCSSAF07008
860 mAh
3.7 V
Single
2.44 x 1.37 x 0.27 in.
0.67 oz.
15 C (12.9A) / 30 C (25.8A)
RCSSAF07009
860 mAh
7.4 V
2S1P
2.44 x 1.37 x 0.59 in.
1.67 oz.
15 C (12.9A) / 30 C (25.8A)
RCSSAF07010
860 mAh
11.1 V
3S1P
2.44 x 1.37 x 0.90 in.
2.40 oz
15 C (12.9A) / 30 C (25.8A)
RCSSAF07011
1350 mAh
3.7 V
Single
3.15 x 1.34 x 0.23 in.
1.00 oz.
15 C (20.2A) / 30 C (40.5A)
RCSSAF07012
1350 mAh
7.4 V
2S1P
3.15 x 1.34 x 0.51 in.
2.79 oz.
15 C (20.2A) / 30 C (40.5A)
RCSSAF07013
1350 mAh
11.1 V
3S1P
3.15 x 1.34 x 0.75 in.
4.05 oz.
15 C (20.2A) / 30 C (40.5A)
RCSSAF07014
1800 mAh
3.7 V
Single
3.80 x 1.34 x 0.27 in.
1.30 oz.
15 C (27A) / 30 C (54A)
RCSSAF07015
1800 mAh
7.4 V
2S1P
3.80 x 1.34 x 0.55 in.
3.57 oz.
15 C (27A) / 30 C (54A)
RCSSAF07016
1800 mAh
11.1 V
3S1P
3.80 x 1.34 x 0.82 in.
5.22 oz.
15 C (27A) / 30 C (54A)
RCSSAF07017
2200 mAh
3.7 V
Single
3.80 x 1.34 x 031 in.
1.72 oz.
15 C (33A) / 30 C (66A)
RCSSAF07018
2200 mAh
7.4 V
2S1P
3.80 x 1.34 x 0.67 in.
3.88 oz.
15 C (33A) / 30 C (66A)
RCSSAF07019
2200 mAh
11.1 V
3S1P
3.80 x 1.34 x 1.18 in.
6.57 oz.
15 C (33A) / 30 C (66A)
RCSSAF07020
3300 mAh
3.7 V
Single
5.04 x 1.69 x 0.23 in.
3.05 oz.
15 C (49.5A) / 30 C (99A)
RCSSAF07021
3300 mAh
7.4 V
2S1P
5.04 x 1.69 x 0.55 in.
6.70 oz.
15 C (49.5A) / 30 C (99A)
RCSSAF07022
3300 mAh
14.8 V
4S1P
5.04 x 1.69 x 1.14 in.
12.91 oz.
15 C (49.5A) / 30 C (99A)
RCSSAF07027
4100 mAh
3.7
Single
5.04 x 1.69 x 0.27 in.
3.7 oz.
15 C (61.5A) / 30 C (123A)
RCSSAF07024
4100 mAh
7.4 V
2S1P
5.04 x 1.69 x 0.59 in.
8.07 oz.
15 C (61.5A) / 30 C (123A)
RCSSAF07025
4100 mAh
14.8 V
4S1P
5.04 x 1.69 x 1.22 in.
14.88 oz.
15 C (61.5A) / 30 C (123A)
RCSSAF07028
New RC System Li-Po packs available in Spring of 2007. The XP Series is for the modeler requiring extreme continuous current
discharge. For example, if you are converting a large SIG Sukhoi SU-31 ARF to electric flight you might use two 5300 mAh 5S1P packs
put in series =10S1P. New generation high performance electric helicopters can also benefit from the RC System XP Series Li-Po packs.
The following XP Series Li-Po packs fitThunder Tiger - mini Titan E325
3S1P 2200 mAh
1x Order No. RCSSAF07035
Thunder Tiger - Raptor E550
5S-6S motor (5S1P or 6S1P Li-Po pack)
6S1P 4500 mAh
1x Order No. RCSSAF07052 or
6S1P 5300 mAh
1x Order No. RCSSAF07057
Thunder Tiger - Raptor E620 SE
6S motor (6S1P Li-Po pack)
6S1P 4500 mAh
1x Order No. RCSSAF07052 or
6S1P 5300 mAh
1x Order No. RCSSAF07057
10S motor (10S1P Li-Po pack)
5S1P 4500 mAh
2x Order No. RCSSAF07051 or
5S1P 5300 mAh
2x Order No. RCSSAF07056
Capacity
Voltaoz.e
Cells
Dimensions
LxWxH
Weioz.ht
Max Discharoz.e
Continuous/Burst
Order No.
1300 mAh
1300 mAh
1800 mAh
1800 mAh
1800 mAh
2200 mAh
2200 mAh
2200 mAh
3300 mAh
3300 mAh
3300 mAh
3300 mAh
3700 mAh
3700 mAh
3700 mAh
3700 mAh
3700 mAh
4500 mAh
4500 mAh
4500 mAh
4500 mAh
4500 mAh
5300 mAh
5300 mAh
5300 mAh
5300 mAh
5300 mAh
7.4 V
11.1 V
7.4 V
11.1 V
14.8 V
7.4 V
14.8 V
18.5 V
11.1 V
14.8 V
18.5 V
22.2 V
7.4 V
11.1 V
14.8 V
18.5 V
22.2 V
7.4 V
11.1 V
14.8 V
18.5 V
22.2 V
7.4 V
11.1 V
14.8 V
18.5 V
22.2 V
2S1P
3S1P
2S1P
3S1P
4S1P
2S1P
4S1P
5S1P
3S1P
4S1P
5S1P
6S1P
2S1P
3S1P
4S1P
5S1P
6S1P
2S1P
3S1P
4S1P
5S1P
6S1P
2S1P
3S1P
4S1P
5S1P
6S1P
3.15 x 1.34 x 0.55 in.
3.15 x 1.34 x 0.86 in.
3.78 x 1.34 x 0.55 in.
3.78 x 1.34 x 0.86 in.
3.78 x 1.34 x 1.18 in.
4.01 x 1.34 x 0.67 in.
4.01 x 1.34 x 1.37 in.
4.01 x 1.34 x 1.69 in.
5.31 x 1.73 x 0.86 in.
5.31 x 1.73 x 1.14 in.
5.31 x 1.73 x 1.45 in.
5.31 x 1.73 x 1.77 in.
5.31 x 1.73 x 0.55 in.
5.31 x 1.73 x 0.90 in.
5.31 x 1.73 x 1.22 in.
5.31 x 1.73 x 1.53 in.
5.31 x 1.73 x 1.89 in.
5.98 x 1.73 x 0.62 in.
5.98 x 1.73 x 0.98 in.
5.98 x 1.73 x 1.30 in.
5.98 x 1.73 x 1.65 in.
5.98 x 1.73 x 2.00 in.
7.40 x 1.81 x 0.63 in.
7.40 x 1.81 x 1.00 in.
7.40 x 1.81 x 1.30 in.
7.40 x 1.81 x 1.65 in.
7.40 x 1.81 x 1.96 in.
3.17 oz.
4.86 oz.
3.88 oz.
5.57 oz.
7.58 oz.
4.09 oz.
8,18 oz.
10.45 oz.
11.28 oz.
14.81 oz.
18.34 oz.
22.40 oz.
7.86 oz.
11.81 oz.
15.52 oz.
19.22 oz.
22.93 oz.
8.92 oz.
13.05 oz.
16.93 oz.
20.98 oz.
25.04 oz.
10.33 oz.
15.16 oz.
19.75 oz.
24.51 oz.
29.27 oz.
25 C (32.5A) / 50 C (65A)
25 C (32.5A) / 50 C (65A)
25 C (45A) / 50 C (90A)
25 C (45A) / 50 C (90A)
25 C (45A) / 50 C (90A)
25 C (55A) / 50 C (110A)
25 C (55A) / 50 C (110A)
25 C (55A) / 50 C (110A)
20 C (66A) / 40 C (132A)
20 C (66A) / 40 C (132A)
20 C (66A) / 40 C (132A)
20 C (66A) / 40 C (132A)
20 C (74A) / 40 C (148A)
20 C (74A) / 40 C (148A)
20 C (74A) / 40 C (148A)
20 C (74A) / 40 C (148A)
20 C (74A) / 40 C (148A)
20 C (90A) / 40 C (180A)
20 C (90A) / 40 C (180A)
20 C (90A) / 40 C (180A)
20 C (90A) / 40 C (180A)
20 C (90A) / 40 C (180A)
20 C (106A) / 40 C (212A)
20 C (106A) / 40 C (212A)
20 C (106A) / 40 C (212A)
20 C (106A) / 40 C (212A)
20 C (106A) / 40 C (212A)
RCSSAF07029
RCSSAF07030
RCSSAF07031
RCSSAF07032
RCSSAF07033
RCSSAF07034
RCSSAF07036
RCSSAF07037
RCSSAF07039
RCSSAF07040
RCSSAF07041
RCSSAF07042
RCSSAF07043
RCSSAF07044
RCSSAF07045
RCSSAF07046
RCSSAF07047
RCSSAF07048
RCSSAF07049
RCSSAF07050
RCSSAF07051
RCSSAF07052
RCSSAF07053
RCSSAF07054
RCSSAF07055
RCSSAF07056
RCSSAF07057
RC System PCB 2S1P Li-Po connector module
RC System PCB 3S1P Li-Po connector module
Indispensable for the correct assembly of individual RC
System Li-Po cells. PCB 2S1P aligns 2 Li-Po cells in series
safely while providing clean soldering points for a Li-Po
battery pack.
Indispensable for the correct assembly of individual RC System Li-Po cells. PCB 3S1P aligns 3 Li-Po cells in series safely
while providing clean soldering points for a Li-Po battery
pack.
Order No. RCSSA10056
Order No. RCSSA10057
RC System PCB 2S2P Li-Po connector module
Indispensable for the correct assembly of individual RC
System Li-Po cells. PCB 2S2P aligns 2 Li-Po cells in series
and 2 in parallel safely while providing clean soldering
points for a Li-Po battery pack.
Order No. RCSSA10058
Order No. RCSSA10058
RC System®
RC System eXtreme Power (XP) Series Li-Po
Accessories
SIG Basswood Assortments
First quality basswood in an assortment of random lengths and sizes. Perfect
for a wide variety of craft and construction uses. Bundle measures approximately 1 x 2 x 24 in.
SIG Basswood Sticks- Bundle
Order No. SIGBA226
Order No. SIGBA226
Assorted thicknesses of 3 or 4 in. wide basswood sheets. Perfect
for a variety of craft uses such as dollhouse construction.
SIG Basswood Sheets- Bundle 2 x 3 x 24 in. Order No. SIGBA239
SIG Basswood Sheets- Bundle 2 x 4 x 24 in. Order No. SIGBA247
Order No. SIGBA239
Basswood is the favorite wood of woodcarvers everywhere. Strong but easy
to carve. The grain in some woods tends to lead your blade in the direction
of the grain. Basswood has a soft grain that makes carving uniform in any
direction. Basswood also takes nearly any stain and easily mimics nearly any
variety of wood depending on the color of stain used. Bundle measures approximately 3 x 12 x 6 ¼ in.
SIG Basswood Block- Bundle
Order No. SIGBA3612
Order No. SIGBA250
Accessories
Nylon Propellers
Especially suited for trainer, control line, or electric model airplanes. More flexible than the Glass Filled Nylon Propellers.
Model Airplane Propellers
Nylon, Yellow
Size
Order No.
6 x 4 in. (15 x 10 cm)
7 x 4 in. (18 x 10 cm)
8 x 4 in. (20 x 10 cm)
8 x 6 in. (20 x 15 cm)
9 x 4 in. (22 x 10 cm)
9 x 6 in. (22 x 15 cm)
10 x 4 in. (25 x 10 cm)
10 x 6 in. (25 x 15 cm)
11 x 6 in. (28 x 15 cm)
11 x 7 3/4 in. (28 x 20 cm)
KAV0057
KAV0058
KAV0059
KAV0060
KAV0061
KAV0062
KAV0063
KAV0064
KAV0065
KAV0066
Order No. KAV0057 - KAV0066
„Low Profile“ Stick-On Steel Weight
Environmentally friendly non-toxic steel weight for balancing of model airplanes and
boats. High quality stick-on tape and the large surface area per section, 0.35 x 0.79
in. (9 x 20 mm) ensures that the weights will stay in place. 2 strips, each with 6
precut sections weighing 0.176 oz (5 g) each. The coated non-lead steel weight is
corrosion resistant. Weight per package is 2.12 oz (60 g).
Order No. KAV0216
Order No. KAV0216
Metal Clevis
Made from high quality heavy gauge spring steel which doesn‘t fatigue with
use. Nickel-plated for a rust free surface and easy soldering if desired.
Pack 2 pcs. Pack 10 pcs.
Thread Order No.
Order No.
2-56 in. KAV000256 KAV00025610
4-40 in. KAV000440 KAV00044010
M2
KAV0004
KAV000410
M 2.5
KAV0004B KAV0004B10
M3
KAV0004A KAV0004A10
Glow Plug Container
Ideal for storing and protecting glow plugs
from dirt and dust. Easily accessible and
transparent for quick stocktaking. Glow
plugs not included.
Glow Plug Container Order No. KAV0037B
Order No. KAV0004
Clear Hinge Tape
The particular plastic selected for Clear Hinge Tape is
flexible, tear resistant and ideally suited for control surface
hinges. The adhesive adheres well to any smooth, clean,
fuel-free surface. Ideal for aileron hinges on sailplanes since it permits no airflow through the hinge line to spoil the
intent of the airfoil. Can be used for all control surfaces.
Not recommended for glow powered airplanes. Length:
32.8 ft. (10 m), Width: 3/4 in. (19 mm).
Clear Hinge Tape
Order No. KAV0037B
Order No. KAV0382
Order No. KAV0382
Electronic Switch
Turn On and Off KAVAN‘s Electromagnetic Brake (Order No. KAV0263), small electric
motors, landing lights, smoke pumps in airplanes or light systems, pumps and horns in
boats. Adjustable On-Off point. 5 amp nominal rating and 10 amp surge. Size: .91 x 1.65 in.
(23 x 42 mm), Weight: .3 oz (8 g). Requires: servo wire with connector.
Mini Electronic Switch
Order No. KAV0230
Order No. KAV0230
Pilots
Handpainted color Pilots made of elastic plastic.
Seat to top of head
Width
Order No.
1- 25/32 in. (45 mm)
4- 7/16 in. (113 mm)
2- 11/64 in. (55 mm)
2- 7/8 in. (73 mm)
KAV0055
KAV3911
Order No. KAV0055 / KAV3911
Finger Guard
For safety and convenience, we recommend using a
KAVAN starter. Finger Guard is the alternative,
designed to help minimize sore fingers sometimes
associated to starting model airplane engines by
hand.
Order No. KAV0056
Finger Guard
Order No. KAV0056
Window Mounting Channel
This soft, highly flexible extrusion makes mounting windows, windshields
and glider canopies in model airplanes, helicopters, boats and cars, quick
and easy. Also good for trimming body edges (e.g. fenders), as a seal in
connection with RC box covers, etc. The double-sided folds can hold
material up to about 1/16 in. (1.5 mm) thick. Compatible with
cyanoacrylate glues.
Window Mounting Channel
Length
Order No.
5 m (16.4 ft)
50 m (164 ft)
KAV0132
KAV0132S
Order No. KAV0132
CA Strengthening Powder
Used in combination with CA glue to fill holes in wood, plastic, metal and
fiberglass. Drip a few drops of CA into a hole, fill the hole with CA Strengthening
Powder. Drip a little more CA into the hole and instantly the compound becomes
hard and strong. CA "Strengthening Powder" sticks to itself. The final repair can
be drilled or sanded. Contents: 1.41 oz. (40 g).
Order No. KAV0107
Order No. KAV0107
Fuel Tank Filler Adapter
Plastic set with protecting cap for mounting in to the fuselage of aircraft or
other models. Provides quick and easy refueling. OK for methanol, gas and
diesel fuel. For fuel lines with inside-ø 5/64 in. (2 mm) to 1/8 in. (3 mm).
Fuel Tank Filler Adapter
Order No. KAV0122
Order No. KAV0122
Glow Plug Thread "Cleaner"
High quality hardened steel chaser die, "cleans" (removes imperfections and
burrs) from 1/4-32 in. glow and spark plug threads. Use on new glow plugs to
optimize the thread and help prevent damage to the relatively soft cylinder
head. Very useful hand-tool for every field box.
Glow Plug Thread "Cleaner"
Order No. KAV0154
Order No. KAV00154
FIRST HOBBY POWER CHARGER 5
Power charger 5 is a rapid charger that has a high performance microprocessor and specialized operating software. An
individual-cell-voltage balancer is built in so it does not need a separate balancer when charging Li-Po batteries. The charger
comes with a 12 V input connector and is able to charge all common battery types like: Ni-CD and Ni-MH with 1 to 14 Cells
from 0.1 to 5 A, 1 to 5 Li-Po/Li-Ion cells with up to 5 A and simultaneous Equalizing, Gel Cell batteries from 2 to 12 V. The
POWER CHARGER 5 is a Multitalent for all Model builders and it doesn't matter whether you prefer gas or electro propulsion.
A comprehensive charge lead set is included to allow you to connect up to a wide range of battery types.
Key Features:
n Charges: Li-Po, Ni-MH, Ni-Cd, Gel Cell Batteries
n 6 Different charge modes: - Li-Po Balanced - Li-Po Regular - Ni-MH - Ni-CD - Gel Cell 6V/12V - User Defined
n JST-XH Balancing Plugs
Specification:
n Input Voltage: 11 - 18 VDC
n Circuit power: max. 50 W
n Charge current range: 0.1 - 5.0 A
n Current drain for balancing Li-Po: 200 mAh/cell
n Ni-MH/Ni-Cd cell count range: 1-14 cells
n Li-Po/Li-Ion cell count range: 1-5 cells
n Gel cell battery voltage: 2 V, 6 V, 12 V
n Weight: 9.9 oz. (280 g)
n Size: 5.1 x 3.2 x 1.1 in. (130 x 80 x 28 mm)
n Large LCD Screen- 16 Characters, 2 Lines
FIRST HOBBY Power Charger 5
Order No. RCSH1300
Order No. RCSH1300
Checkerboard Printed Japanese Tissue
Lightweight checkerboard tissue printed with
gloss ink for an elegant scale appearance.
Also available in printed silver (not checkerboard).
Esaki Plyspan made in Japan.
Weight: 5 grams per sheet, Checkerboard size: 1/2
in (12 mm), Sheet size: 17 3/4 x 23 1/2 in (450 x
600 mm)
Checkerboard Printed Japanese Tissue
Color(s)
Order No.
Black/Red
Black/White
Black/Yellow
Cub Yellow/White
Fire Red /White
Sky Blue/White
SIGPPL001
SIGPPL002
SIGPPL003
SIGPPL004
SIGPPL005
SIGPPL006
Silver
(not pictured)
SIGPPL100
RCS SimTransmitter with FMS Flight Simulator
There are different ways to learn R/C model flying. If an experienced model
flyer is not on site then the first steps can be disappointing. At worst case
you could crash your first model. Especially for learning R/C helicopter
flying the so called “Dry Run” on a simulator is an inexpensive and suggested method. The 6 Channel SimTransmitter “Joystick” with the included
FMS Flying-Model-Simulator provides the ideal virtual beginner airplane or
helicopter “model”. Simply plug the SimTransmitter into a free USB port and
configure it as a joystick.
System requirements
„Windows 98 SE/Windows 2000/Windows XP
„OpenGL/DirectX graphic board with min. 64 MB memory
„Min. 600 MHz Intel or AMD Processor and 256 MB memory
The FMS Simulator is NOT compatible with Windows Vista. FMS Flight
Simulator can also be downloaded for free on the Internet.
RCS SimTransmitter with FMS Flight Simulator
Order No. RCSSIM062
KAVAN Mini Hand Drill w/ 12 Drill Bits
Quick and easy way to drill small holes. “Must have” tool in the field box for emergency repairs. Includes 12 drill bits stored inside the aluminum handle, sizes range
from .024 in (0.6 mm) to .063 in (1.6 mm). Length: 4- 1/8 in (10.5 cm).
KAVAN Mini Hand Drill w/ 12 Drill Bits
Order No. KAV0670
Order No. KAV0670
KAVAN Wheel Collars
Metric sizes fit most ARFs and kits manufactured outside of the
USA. Nickel-plated brass. Includes socket set screws (Order No.
KAV0041) and one hex wrench (Order No. KAV0042).
Pack: 5 Wheel Collars
For axle-ø
Order No.
2 mm (.08 in)
3 mm (.12 in)
4 mm (5/32 in)
5 mm (.08 in)
6 mm (.24 in)
1/8 in (3.2 mm)
KAV0262F
KAV0262E
KAV0262D
KAV0262C
KAV0262A
KAV0262G
KAVAN Hexagon Socket Wrench Key
KAVAN Hexagon Socket Wrench Key
Steel, DIN 911
Order No. KAV0262F
KAVAN Steel Axle Shafts
Bolt to any aluminum or fiberglass landing gear. Easy installation: either tap a thread in the landing gear equal to the
“Mounting Thread” size or mount in an untapped hole using the
included steel hex nut and lock washer. Since the KAVAN Axle
Shafts install from the inside of the landing gear, the removal of
wheels (when wheel pants are attached to the landing gear), is
much easier. Includes 4 wheel collars and 1 hex wrench. Zinc
plated steel.
Size
Pack/pcs.
Order No.
1.5 mm
2 mm
2.5 mm
3 mm
4 mm (5/32 in)
1.5/2/2.5/3/4 mm
2
2
2
2
2
5 (1 each)
KAV0042
KAV0042A
KAV0042B
KAV0042C
KAV0042D
KAV0042S
Pack: 1 pair.
Axle-ø
Shaft
Length
5/32 in (4 mm)
3/16 in (4.76 mm)
5 mm
6 mm
50
50
50
60
mm
mm
mm
mm
Mounting Order No.
Thread
(2 in)
(2 in)
(2 in)
(2- 3/8 in)
M7
M8
M8
M10
KAV6162
KAV6163
KAV6164
KAV6165
KAVAN Steel Axle Shafts
KAVAN Rubber Shock Mounts
Make your own shock motor mount. Ideal to absorb engine vibration or for elastic fastening of exhaust systems. The special medium hard rubber is glow fuel
and gasoline resistant. Especially suited for 4-stroke engines.
Type A: Threaded stud on each side. Type B: Threaded stud on one side and
tapped hole on the other.
Pack: 4 pcs.
Nos. KAV3025, KAV3034, KAV3024, KAV3038, KAV3028
Type
A
A
A
B
B
Thread
M3
M4
M6
M4
M6
Thread Length
.25 in (6 mm)
.4 in (10 mm)
.6 in (15 mm)
.4 in (10 mm)
.6 in (15 mm)
Rubber-ø
.32 in (8 mm)
.6 in (15 mm)
.8 in (20 mm)
.6 in (15 mm)
.8 in (20 mm)
Rubber Length
.32 in (8 mm)
.6 in (15 mm)
.6 in (15 mm)
.6 in (15 mm)
.6 in (15 mm)
KAVAN Plastic Clamps
With parallel jaws, useful for fuselage assembly or any other situation where
you need a temporary “helping hand”. Available in two sizes:
Jaw Length
Length Overall
Clear Span
Pack/Pcs.
Order No.
1 in (25mm)
2 in (50mm)
2.6 in (66 mm)
5.8 in (148 mm)
up to 1.4 in (36 mm)
up to 4.3 in (110 mm)
5
2
KAV0127
KAV0128
Order No.. KAV0128, KAV0127
Order No.
KAV3025
KAV3024
KAV3028
KAV3034
KAV3038
Shaft-Lock Spinner Nut
An electric starter or backfiring 4-stroke engine will not loosen this Spinner Nut.
Simple to install: Hold the Spinner Nut with a 7/8 in (22 mm) wrench and then
tighten the included socket set screw against the engine shaft. Dimension: 7/8
x 1 in (22 x 26 mm). Weight: 1 oz (28 g). Includes hex wrench.
Shaft-Lock Spinner Nut
Engine Shaft
Hex Wrench (incl)
Order No.
1/4- 28 in
5/16- 24 in
3/8 - 24 in.
M6x1
M7x1
M 8 x 1.25
M8x1
1/8 in
5/32 in
3/16 in
3 mm
5/32 in
5/32 in
5/32 in
KAV0294
KAV0295
KAV0300
KAV0296
KAV0297
KAV0298
KAV0299
( 4 mm)
( 4 mm)
( 4 mm)
( 4 mm)
Shaft-Lock Spinner Nut
KAVAN Display for SuperLight Deluxe AirWheels (for the Dealer)
This attractive 4-color printed display with German and English text is a space saving and environmentally friendly alternative
to wheels packaged in pairs. It fits conveniently on a shelf, counter or hangs on a pegboard. Factory assembled and loaded
with wheels in seven sizes, six each ranging from 1-1/2 in (40 mm) to 3 in (75 mm) diameter. Remove and fill the display from
the left, right and front sides. Size: 7.7 in (19.5 cm) depth x 5.9 in (15 cm) width x 10.4 in (26 cm) height (excluding rear plug in
sign). Maximum Capacity: 60 wheels.
Display with 42 Deluxe AirWheels Order No. KAV6390
Display without Wheels Order No. KAV6395
Refill wheels:
Minimum dealer order quantity:
6 pcs. per size, bulk.
Wheel-ø
Order No.
1-1/2 in (40 mm)
1-3/4 in (45 mm)
2 in (50 mm)
2-1/4 in (56 mm)
2-1/2 in (62 mm)
2-3/4 in (68 mm)
3 in (75 mm)
KAV0097AL
KAV0097L
KAV0098L
KAV0099L
KAV0100L
KAV0101L
KAV0102L
Order No. KAV6390
KAVAN Quick-Prop 5 x 4
Press fits on 280 - 480 size motors with a shaft diameter of 2 - 2.3 mm.
Simply secured with a drop of CA. Comparable with Günther prop 5 x 4
but with a new design for greater efficiency.
KAVAN Quick-Prop 5 x 4 Order No. KAV6471
Order No. KAV6471
Dual Lock
Plastic material with “knobs” and a self-stick adhesive backing. Cut into small pieces
and stick onto the bottom of a servo, nicad, etc. and another piece on the airplane,
car or boat cabin floor. The Servo is locked in to place as the little plastic “knobs”
interlock. There is less side to side movement with Dual Lock as compared to a
“hook and loop fastener” such as VELCRO®. Width: 1 in (25 mm). Length: 19- 11/16”
(500 mm).
Dual Lock
Order No. KAV0647
Order No. KAV0647