DENON CONTROL PROTOCOL 3803_Ver.3.18_

Transcription

DENON CONTROL PROTOCOL 3803_Ver.3.18_
DENON AVR/AVC control protocol
Ver. 3.18
Application model : AVR-3803(AVC-3570) From Serial Number XXX1512251 and up
Application terminal : Serial Port
Connector specification
Connector type : 3.5mm Stereo Mini Plug
( Tip: RXD , Middle Band: TXD , Base: GND)
Communication format :
Synchronous system
: Tone step synchronization
communication system
: A half duplex
Communication speed
: 9600bps
Character length
: 8 bits
Parity control
: None
Start bit
: 1 bit
Stop bit
: 1 bit
Communication procedure
: Non procedural
Communication data length
: 135 bytes (maximum)
-1-
Protocol specification
The following three data forms is defined.
COMMAND :
The message sent to a system(AVR/AVC) from a controller(Touch Panel etc.)
A command to a system is given from a controller.
EVENT
:
The message sent to a controller(Touch Panel etc.) from a system(AVR/AVC)
The result is sent, when a system is operated directly and a state changes.
*The form of EVENT presupposes that it is the same as that of COMMAND.
**Refer to the following table for the contents of COMMAND and EVENT.
RESPONSE :
The message sent to a controller(Touch Panel etc.) from a system(AVR/AVC)
if the ‘request command’ (COMMAND+?+CR(0x0D)) has came from a controller.
The RESPONSE should be sent within 200ms of receiving the COMMAND.
*The form of RESPONSE presupposes that it is the same as that of EVENT.
Basic specification : The command by ASCII CODE, parameter expression
*ASCII CODE which can be used is from 0x20 to 0x7F : the alphabet and the number of 0-9 , and space (0x20) , Some signs ,
AND carriage return(0x0D)--- It is used only as a pause sign.
Command structure : COMMAND + PARAMETER + CR(0x0D)
COMMAND : ASCII CODE of 2 characters
ex.
SI : Select Input source
MS : surround Mode Setting
MV : Master Volume setting
PW : system PoWer setting
PARAMETER : ASCII CODE ( up to 25 characters)
ex.
DVD : function name
CDR/TAPE-1 : function name
THX SURROUND EX : surround mode name
SUPER STADIUM : surround mode name
*Special Parameter--- ? : for request command
-2-
The example of a command
* <CR> is the meaning of 0x0D.
SIDVD<CR> : Select Input source DVD
MSTHX SURROUND EX<CR> : surround Mode Set to THX SURROUND EX
MVUP<CR> : Master Volume UP
PWON<CR> : system PoWer ON
PWSTANDBY<CR> : system PoWer STANDBY
SI?<CR> : Request command for now playing input source >> Return RESPONSE ‘SI***<CR>’
Others
A) COMMAND is receivable also during transmission of EVENT.
B) Since CHANNEL VOLUME changes simultaneously when the SURROUND MODE changes, the value of the channel volume of all channels
returns as EVENT.
C) CHANNEL VOLUME returns the data of ALL channels by the present SURROUND MODE also including an intact channel. In this case,
the data of an intact channel is set to "50".
D) Since SURROUND MODE changes simultaneously when the INPUT source changes, the SURROUND MODE (and also the value of the channel
volume of all channels , It described in B) ) returns as EVENT.
E) When SURROUND MODE is the same in between INPUT source change before and after, EVENT of SURROUND MODE and CHANNEL VOLUME
does NOT return.
F) Although EVENT of SURROUND MODE returns when the present SURROUND MODE is set up again, CHANNEL VOLUME does NOT return.
G) When SURROUND MODE is changed, before returning SURROUND MODE after change as EVENT, the present SURROUND MODE is returned.
H) The RESPONSE should be sent as opposed to the request command by all the commands with which an EVENT exists , not need to
the another request commands(ex. SV command).
I) AVR-3803 can control MASTER VOLUME & CHANNEL VOLUME with 0.5dB step, but this COMMAND can’t send direct change with 0.5dB
accuracy.(It can adjust with UP/DOWN PARAMETER.)
J) In AVR-3803, the RESPONSE of MASTER VOLUME & CHANNEL VOLUME still returned **(2 characters) with round off a *.5dB step.
K) The PARAMETER (with COMMAND and RESPONSE, EVENT) of minimum level of MASTER VOLUME and defines “99”.
-3-
L) COMMAND and PARAMETER list
COMMAND
PW
MV
CV
PARAMETER
ON
STANDBY
UP
DOWN
**
FL UP
FL DOWN
FL **
FR UP
FR DOWN
FR **
C UP
C DOWN
C **
SW UP
SW DOWN
SW **
SL UP
SL DOWN
SL **
SR UP
SR DOWN
SR **
SBL UP
SBL DOWN
SBL **
SBR UP
SBR DOWN
SBR **
function
POWER ON/STANDBY change
MASTER VOLUME UP/DOWN , direct change to ***dB
**:00 to 99 by ASCII , 80=0dB, 99=---(MIN)dB
CHANNEL VOLUME UP/DOWN , direct change to ***dB
---FRONT Lch
**:38 to 62 by ASCII , 50=0dB
---FRONT Rch
**:38 to 62 by ASCII , 50=0dB
---CENTERch
**:38 to 62 by ASCII , 50=0dB
---SUBWOOFERch
**:38 to 62 by ASCII , 50=0dB
---SURROUND Lch
**:38 to 62 by ASCII , 50=0dB
---SURROUND Rch
**:38 to 62 by ASCII , 50=0dB
---SURROUND BACK Lch (SBch 2SP)
**:38 to 62 by ASCII , 50=0dB
---SURROUND BACK Rch (SBch 2SP)
**:38 to 62 by ASCII , 50=0dB
-4-
example
PWON<CR>
PWSTANDBY<CR>
MVUP<CR>
MVDOWN<CR>
MV80<CR>
CVFL UP<CR>
CVFL DOWN<CR>
CVFL 50<CR>
CVFR UP<CR>
CVFR DOWN<CR>
CVFR 50<CR>
CVC UP<CR>
CVC DOWN<CR>
CVC 50<CR>
CVSW UP<CR>
CVSW DOWN<CR>
CVSW 50<CR>
CVSL UP<CR>
CVSL DOWN<CR>
CVSL 50<CR>
CVSR UP<CR>
CVSR DOWN<CR>
CVSR 50<CR>
CVSBL UP<CR>
CVSBL DOWN<CR>
CVSBL 50<CR>
CVSBR UP<CR>
CVSBR DOWN<CR>
CVSBR 50<CR>
COMMAND
CV
MU
SI
ZM
Z1
PARAMETER
SB UP
SB DOWN
SB **
ON
OFF
PHONO
CD
TUNER
DVD
VDP
TV
DBS/SAT
VCR-1
VCR-2
VCR-3
V.AUX
CDR/TAPE1
MD/TAPE2
ON
OFF
PHONO
|
CDR/TAPE1
SOURCE
UP
DOWN
**
ON
OFF
example
CVSB UP<CR>
CVSB DOWN<CR>
**:38 to 62 by ASCII , 50=0dB
CVSB 50<CR>
OUTPUT MUTE ON/OFF change
MUON<CR>
MUOFF<CR>
Select INPUT source
SIPHONO<CR>
SICD<CR>
SITUNER<CR>
SIDVD<CR>
SIVDP<CR>
SITV<CR>
---Select DBS function at AVR-3803
SIDBS/SAT<CR>
SIVCR-1<CR>
SIVCR-2<CR>
---Invalid at AVR-3803
SIVCR-3<CR>
SIV.AUX<CR>
---Select CDR/TAPE function at AVR-3803
SICDR/TAPE1<CR>
---Invalid at AVR-3803
SIMD/TAPE2<CR>
MAIN-ZONE ON/OFF change
ZMON<CR>
ZMOFF<CR>
MULTI ZONE-1 mode set , and select source
Z1PHONO<CR>
---The name of PARAMETER is
|
the same as that of the time of SI COMMAND.
Z1CDR/TAPE1<CR>
MULTI ZONE-1 mode cancel
Z1SOURCE<CR>
MULTI ZONE-1 VOLUME UP/DOWN , direct change to ***dB Z1UP<CR>
Z1DOWN<CR>
**:00 to 99 by ASCII , 80=0dB, 00= ---(MIN)
Z180<CR>
MULTI ZONE-1 ON/OFF change
Z1ON<CR>
Z1OFF<CR>
---Set ZONE-2 functions at AVR-3803
---SURROUND BACKch
function
(SBch 1SP)
-5-
COMMAND
Z2
SR
SV
SD
PARAMETER
PHONO
|
MD/TAPE2
SOURCE
UP
DOWN
**
ON
OFF
PHONO
|
CDR/TAPE1
SOURCE
DVD
VDP
TV
DBS/SAT
VCR-1
VCR-2
VCR-3
V.AUX
SOURCE
AUTO
PCM
DTS
RF
ANALOG
EXT.IN-1
EXT.IN-2
function
MULTI ZONE-2 mode set , and select source
---The name of PARAMETER is
the same as that of the time of SI COMMAND.
MULTI ZONE-2 mode cancel
MULTI ZONE-2 VOLUME UP/DOWN , direct change to ***dB
**:00 to 99 by ASCII , 80=0dB
MULTI ZONE-2 ON/OFF change
---Invalid at AVR-3803
REC SELECT mode set , and select source
---The name of PARAMETER is
the same as that of the time of SI COMMAND.
REC SELECT mode cancel
VIDEO SELECT mode set , and select source
---Invalid at AVR-3803
VIDEO SELECT mode cancel
set DIGITAL INPUT AUTO mode
set DIGITAL INPUT force PCM mode
set DIGITAL INPUT force DTS mode
---Invalid at AVR-3803
set force ANALOG INPUT mode
set EXT.IN-1 mode ---Set EXT.IN mode at AVR-3803
set EXT.IN-2 mode ---Invalid at AVR-3803
-6-
example
Z2PHONO<CR>
|
Z2MD/TAPE2<CR>
Z2SOURCE<CR>
Z2UP<CR>
Z2DOWN<CR>
Z280<CR>
Z2ON<CR>
Z2OFF<CR>
SRPHONO<CR>
|
SRCDR/TAPE1<CR>
SRSOURCE<CR>
SVDVD<CR>
SVVDP<CR>
SVTV<CR>
SVDBS/SAT<CR>
SVVCR-1<CR>
SVVCR-2<CR>
SVVCR-3<CR>
SVV.AUX<CR>
SVSOURCE<CR>
SDAUTO<CR>
SDPCM<CR>
SDDTS<CR>
SDRF<CR>
SDANALOG<CR>
SDEXT.IN-1<CR>
SDEXT.IN-2<CR>
EVENT
MS
PARAMETER
DIRECT
PURE DIRECT
STEREO
DOLBY PRO LOGIC
DOLBY PL2
DOLBY DIGITAL
DOLBY D EX
DTS NEO:6
DTS SURROUND
DTS ES DSCRT6.1
DTS ES MTRX6.1
HOME THX CINEMA
THX5.1
THX6.1
THX SURROUND EX
WIDE SCREEN
5CH STEREO
7CH STEREO
SUPER STADIUM
ROCK ARENA
JAZZ CLUB
CLASSIC CONCERT
MONO MOVIE
VIDEO GAME
MATRIX
VIRTUAL
function
SURROUND mode set
All are received as "DOLBY SURROUND" ,
the surround mode which changed return as EVENT.
All are received as "DTS SURROUND" ,
the surround mode which changed return as EVENT.
---Invalid
---Invalid
---Invalid
---Invalid
at
at
at
at
AVR-3803
AVR-3803
AVR-3803
AVR-3803
Both are received as "5CH/7CH STEREO" ,
the surround mode which changed return as EVENT.
-7-
example
MSDIRECT<CR>
MSPURE DIRECT<CR>
MSSTEREO<CR>
MSDOLBY PRO LOGIC<CR>
MSDOLBY PL2<CR>
MSDOLBY DIGITAL<CR>
MSDOLBY D EX<CR>
MSDTS NEO:6<CR>
MSDTS SURROUND<CR>
MSDTS ES DSCRT6.1<CR>
MSDTS ES MTRX6.1<CR>
MSHOME THX CINEMA<CR>
MSTHX5.1<CR>
MSTHX6.1<CR>
MSTHX SURROUND EX<CR>
MSWIDE SCREEN<CR>
MS5CH STEREO<CR>
MS7CH STEREO<CR>
MSSUPER STADIUM<CR>
MSROCK ARENA<CR>
MSJAZZ CLUB<CR>
MSCLASSIC CONCERT<CR>
MSMONO MOVIE<CR>
MSVIDEO GAME<CR>
MSMATRIX<CR>
MSVIRTUAL<CR>
EVENT
PS
TF
TP
PARAMETER
TONE DEFEAT ON
TONE DEFEAT OFF
SB:MTRX ON
SB:NON MTRX
SB:OFF
CINEMA EQ.ON
CINEMA EQ.OFF
MODE : MUSIC
MODE : CINEMA
MODE : EMULATION
UP
DOWN
****** (6 digits)
UP
DOWN
**(PRESET No.)
function
PARAMETER setting
TONE DEFEAT ON/OFF
SURROUND BACK SP MODE set
---MTRX ON = SURR.EX ON = DSCRT ON
(at THX mode) (at ES DSCRT mode)
CINEMA EQ. ON/OFF
CINEMA / MUSIC /PL mode change
(This parameter can change DOLBY PL2,NEO:6 mode.)
--- “EML” can change ONLY DOLBY PL2 mode.
TUNER Frequency UP/DOWN , direct change
--- ****.** kHz at AM band (>050000 is AM.)
****.** MHz at FM band (<050000 is FM.)
TUNER PRESET CH UP/DOWN , direct change to No.**
TUNER BAND , MODE Select
AM
---Band set to AM
FM
---Band set to FM
AUTO
---Tuning mode set to AUTO mode
MANUAL
---Tuning mode set to MANUAL mode
TF, TP, TM COMMAND : '*' parameters can NOT operate when INPUT source isn’t TUNER.
example
PSTONE DEFEAT ON<CR>
PSTONE DEFEAT OFF<CR>
PSSB:MTRX ON<CR>
PSSB:NON MTRX<CR>
PSSB:OFF<CR>
PSCINEMA EQ.ON<CR>
PSCINEMA EQ.OFF<CR>
PSMODE : MUSIC<CR>
PSMODE : CINEMA<CR>
PSMODE : EMULATION<CR>
TFUP<CR>
TFDOWN<CR>
TF105000<CR>
(1050.00kHz at AM)
TPUP<CR>
TPDOWN<CR>
TPA1<CR>
(PRESET No.”A1”)
*
*
TM
-8-
TMAM<CR>
TMFM<CR>
TMAUTO<CR>
TMMANUAL<CR>
*
*
EVENT(or RESPONSE) and PARAMETER list
EVENT
PW
MV
CV
PARAMETER
ON
STANDBY
**
function
POWER ON/STANDBY change
MASTER VOLUME change , **:00 to 99 by ASCII
98 = +18dB(MAX)
80 = 0dB
00 = -80dB
99 = --- (MIN)
CHANNEL VOLUME change , **:38 to 62 by ASCII
62 = +12dB(MAX)
50 = 0dB
38 = -12dB(MIN)
00 = OFF (define ONLY SWch in DIRECT mode.)
FL **
FR **
C **
SW **
SL **
SR **
SBL **
(at SBch 2SP)
SBR **
(at SBch 2SP)
SB **
(at SBch 1SP)
MU
ON
OUTPUT MUTE ON/OFF change
OFF
SI
PHONO
INPUT source change
CD
TUNER
DVD
VDP
TV
DBS/SAT
---Select DBS function at AVR-3803
VCR-1
VCR-2
VCR-3
---Invalid at AVR-3803
V.AUX
CDR/TAPE1
---Select CDR/TAPE function at AVR-3803
MD/TAPE2
---Invalid at AVR-3803
*RES. : NOT returns '*' parameters as RESPONSE.
-9-
example
PWON<CR>
PWSTANDBY<CR>
MV80<CR>
CVFL 50<CR>
CVFR 50<CR>
CVC 50<CR>
CVSW 50<CR>
CVSL 50<CR>
CVSR 50<CR>
CVSBL 50<CR>
CVSBR 50<CR>
CVSB 50<CR>
MUON<CR>
MUOFF<CR>
SIPHONO<CR>
SICD<CR>
SITUNER<CR>
SIDVD<CR>
SIVDP<CR>
SITV<CR>
SIDBS/SAT<CR>
SIVCR-1<CR>
SIVCR-2<CR>
SIVCR-3<CR>
SIV.AUX<CR>
SICDR/TAPE1<CR>
SIMD/TAPE2<CR>
*RES.
EVENT
ZM
Z1
PARAMETER
ON
OFF
PHONO
|
CDR/TAPE1
SOURCE
**
ON
OFF
Z2
PHONO
|
CDR/TAPE1
SOURCE
**
ON
OFF
SR
TF
PHONO
|
CDR/TAPE1
SOURCE
****** (6 digits)
function
MAIN-ZONE ON/OFF change
MULTI ZONE-1 source change
---The name of PARAMETER is
the same as that of the time of SI COMMAND.
MULTI ZONE-1 mode cancel
MULTI ZONE-1 VOLUME change , **:00 to 99 by ASCII
98 = +18dB(MAX)
80 = 0dB
10 = -70dB
00=---(MIN)
MULTI ZONE-1 ON/OFF change
---means MULTI ZONE functions at AVR-3803
MULTI ZONE-2 source change
---The name of PARAMETER is
the same as that of the time of SI COMMAND.
MULTI ZONE-2 mode cancel
MULTI ZONE-2 VOLUME change , **:00 to 99 by ASCII
98 = +18dB(MAX)
80 = 0dB
10 = -70dB
00=---(MIN)
MULTI ZONE-2 ON/OFF change
---Invalid at AVR-3803
REC SELECT source change
---The name of PARAMETER is
the same as that of the time of SI COMMAND.
REC SELECT mode cancel
TUNER Frequency change
--- ****.** kHz at AM band
****.** MHz at FM band
- 10 -
example
ZMON<CR>
ZMOFF<CR>
Z1PHONO<CR>
|
Z1CDR/TAPE1<CR>
Z1SOURCE<CR>
Z180<CR>
Z1ON<CR>
Z1OFF<CR>
Z2PHONO<CR>
|
Z2CDR/TAPE1<CR>
Z2SOURCE<CR>
Z280<CR>
Z2ON<CR>
Z2OFF<CR>
SRPHONO<CR>
|
SRCDR/TAPE1<CR>
SRSOURCE<CR>
TF105000<CR>
(1050.00kHz at AM)
*RES.
EVENT
TP
PARAMETER
**(PRESET No.)
TM
MS
AM
FM
AUTO
MANUAL
DIRECT
PURE DIRECT
STEREO
DOLBY PRO LOGIC
DOLBY PL2
DOLBY DIGITAL
DOLBY D EX
DTS NEO:6
DTS SURROUND
DTS ES DSCRT6.1
DTS ES MTRX6.1
HOME THX CINEMA
THX5.1
THX6.1
THX SURROUND EX
WIDE SCREEN
5CH STEREO
7CH STEREO
SUPER STADIUM
ROCK ARENA
JAZZ CLUB
CLASSIC CONCERT
MONO MOVIE
VIDEO GAME
MATRIX
VIRTUAL
function
TUNER PRESET change to No.**
TUNER BAND , MODE change
---Band set to AM
---Band set to FM
---Tuning mode set to AUTO mode
---Tuning mode set to MANUAL mode
SURROUND mode change
---Invalid
---Invalid
---Invalid
---Invalid
at
at
at
at
AVR-3803
AVR-3803
AVR-3803
AVR-3803
- 11 -
example
TPA1<CR>
(PRESET No.”A1”)
TMAM<CR>
TMFM<CR>
TMAUTO<CR>
TMMANUAL<CR>
MSDIRECT<CR>
MSPURE DIRECT<CR>
MSSTEREO<CR>
MSDOLBY PRO LOGIC<CR>
MSDOLBY PL2<CR>
MSDOLBY DIGITAL<CR>
MSDOLBY D EX<CR>
MSDTS NEO:6<CR>
MSDTS SURROUND<CR>
MSDTS ES DSCRT6.1<CR>
MSDTS ES MTRX6.1<CR>
MSHOME THX CINEMA<CR>
MSTHX5.1<CR>
MSTHX6.1<CR>
MSTHX SURROUND EX<CR>
MSWIDE SCREEN<CR>
MS5CH STEREO<CR>
MS7CH STEREO<CR>
MSSUPER STADIUM<CR>
MSROCK ARENA<CR>
MSJAZZ CLUB<CR>
MSCLASSIC CONCERT<CR>
MSMONO MOVIE<CR>
MSVIDEO GAME<CR>
MSMATRIX<CR>
MSVIRTUAL<CR>
*RES.

Similar documents

2015 Polish Mountain Hill Climb Results.

2015 Polish Mountain Hill Climb Results. American Sedan Improved Touring A Improved Touring B Improved Touring C Improved Touring E Improved Touring S Super Street Prepared A Street Prepared B Street Prepared C Street Prepared D Street Pr...

More information