Windows Setup Guide for ST-70

Transcription

TOSHIBA TEC CORPORATION
Table of Contents
1. Introduction........................................................................................................................... 1
2. Set up of Windows XP .......................................................................................................... 2
1)
Setting up BIOS.................................................................................................................. 2
2)
Installing Windows.............................................................................................................. 2
3)
Adding a serial port............................................................................................................. 2
4)
Installing the 4 in 1 Chipset Software.................................................................................. 3
5)
Installing the Network Driver ............................................................................................... 5
6)
Installing the Graphic Driver ............................................................................................... 6
7)
Installing the USB 20. Driver............................................................................................... 8
8)
Installing the Audio Driver................................................................................................. 10
9)
Installing the PnP Touch Panel Driver............................................................................... 12
3. Setup of Windows 2000 ...................................................................................................... 14
1)
Setting up BIOS................................................................................................................ 14
2)
Installing Windows............................................................................................................ 14
3)
Adding a serial port........................................................................................................... 14
4)
Installing the 4 in 1 Chipset Software................................................................................ 15
5)
Installing the Network Driver ............................................................................................. 17
6)
Installing the Graphic Driver ............................................................................................. 18
7)
Installing the USB2.0 Driver.............................................................................................. 20
8)
9)
10) Precautions for Use of PC Cards...................................................................................... 26
4. Set up of Windows NT ........................................................................................................ 27
1)
Setting up BIOS................................................................................................................ 27
2)
3)
Installing the Service Pack (SP)........................................................................................ 27
4)
5)
Changing/Adding the Serial Port....................................................................................... 29
6)
7)
8)
9)
10) Precaution for Use of PC Cards........................................................................................ 34
5. Set up of Windows 98SE .................................................................................................... 36
1)
Setting up BIOS................................................................................................................ 36
2)
3)
Changing the Serial Port Setting....................................................................................... 37
4)
5)
6)
7)
Installing USB 2.0 Driver................................................................................................... 44
8)
9)
10) Precaution for Use of PC Cards........................................................................................ 48
11) Precaution for Use of CF .................................................................................................. 49
1
1. Introduction
This setup guide describes the procedure and notes for installing the ST-70 driver on the ST-70.
The outline of the set up procedure for the ST-70’s OS is as follows.
Outline of the set up procedure for the Windows in the ST-70
1)
Setting up BIOS
2)
Installing Windows
3)
Changing the Serial Port Settings
4)
Installing the 4 in 1 Chipset Software
5)
6)
7)
Installing the Network Driver
Installing the Graphic Driver
Installing the USB 2.0 Driver
8)
9)
Installing the Audio Driver
Installing the PnP Touch Panel Driver
This install kit supports Windows XP and Windows2000.
Windows NT and Windows 98SE are not supported officially, however, the driver operation has been
confirmed.
2
2. Set up of Windows XP
1) Setting up BIOS
By pressing the F2 key on the keyboard when the machine starts up, the machine enters the
BIOS Setup Menu. Select the following item for BIOS setup.
[Exit] menu → Load Setup Defaults (Win XP)
2) Installing Windows
Install Windows XP on the machine.
Some drivers may require the service pack of the new version. Install the necessary service pack.
For installing USB 2.0 driver, SP1 or greater is required.
3) Adding a serial port
After installing Windows XP, the Device Manager shows the serial port status as follows.
As the COM port which is supposed to be “Communications Port (COM6)” is displayed as
“Communications Port (COM5)”, this setting needs to be changed.
Open the Communications Port (COM5) Properties screen, click on the Port Setting tab, and then,
click on the [Advanced..] button.
3
Change the COM Port Number from “COM5” to “COM6”.
4) Installing the 4 in 1 Chipset Software
Run the “VIAChipset\VIAHyperion 4in1 448v.exe” file in the driver kit. When the following screen
appears, click on the [Next] button.
When the following screen appears, click on the [Yes] button.
4
Choose the “Normal Installation”, and click on the [Next] button.
After confirming that “VIA PCI IDE Bus Driver”, “AGP Driver” and “VIA INF Driver” are all selected,
click on the [Next] button to start the installation. Reboot the machine when requested.
5
5) Installing the Network Driver
On the Device Manager screen, open the property screen of the VIA Compatible Fast Ethernet
Adapter in the Network adapters.
Click on the [Update Driver..] button to start the Update Device Driver Wizard. Select the “VIA\lan”
folder in the install kit for the driver path, and continue the installation.
6
“VIA Rhine II Fast Ethernet Adapter” is installed.
6) Installing the Graphic Driver
Open the property screen of the Video Controller (VGA Compatible) shown with a question mark
(?) on the Device Manager screen.
7
Click on the [Update Driver..] button to start the Update Device Driver Wizard. Select the
“VIA\VGA\w2kxp” folder in the install kit for the driver path, and continue the installation.
The “VIA\S3G CLE266” is installed.
8
7) Installing the USB 20. Driver
Since USB 2.0 is supported from Windows XP SP1, it is necessary to install the SP1 or greater
and follow the procedure described below to use USB 2.0.
Run the “VIA\usb\Setup.exe” file in the driver kit. When the following screen appears, click on the
[Next] button.
When the following screen appears during the installation process, click on the [Yes] button.
When the installation has finished, the ST-70 will be automatically rebooted.
9
When not using the SP1 or greater, install the filter driver using the following procedure.
[Next] button.
Choose the “Install VIA USB filter driver” and click on the [Next] button on the screen below.
When the installation is completed, the machine is rebooted.
10
8) Installing the Audio Driver
Open the property screen of the “Multimedia Audio Controller” shown with a question mark (?) on
the Device Manager screen.
“VIA\audio\Wdm” folder in the install kit for the driver path, and continue the installation.
11
The “VIA AC97 Enhanced Audio Controller (WDM)” is installed.
To display the sound icon in the task bar, open the Sound and Audio Devices Properties screen in
the Control Panel, and check the “Place volume icon in the taskbar” on the Volume page.
12
9) Installing the PnP Touch Panel Driver
Open the property screen of the “SMK PnP TABLET” shown with a question mark (?) on the
Device Manager screen.
“Tablet\PnPTablet\Win2kxp” folder in the install kit for the driver path, and continue the installation.
13
When the following screen appears, click on the [Continue Anyway] button.
The “SMK PnP Tablet” is installed.
Open the Touch Panel Properties screen in the Control Panel. When the Touch Panel Properties
screen appears, click on the [Calibration] button and the [Execute] buttons, in order, to set the
calibration.
IMPORTANT
Unless any of the PS/2 mouse, the serial mouse, or the USB mouse is
connected, the touch panel driver cannot be loaded properly, and calibration
cannot be set. When installing the driver, connect any of the mice and let the
machine detect the mouse.
14
3. Setup of Windows 2000
1) Setting up BIOS
[Exit] Menu → Load Setup Defaults (Win 2000)
Install Windows 2000 on the ST-70.
For installing USB 2.0 driver, SP4 or greater is required.
3) Adding a serial port
After installing Windows 2000, the Device Manager shows the serial port status as follows.
“Communications Port (COM5)”, this setting needs to be changed.
Open the Communications Port (COM5) Properties screen, click on the Port Settings tab, and
then, click on the [Advanced..] button.
15
Change the COM Port Number from “COM5” to “COM6”.
Run the “VIA\Chipset\VIAHyperion 4in1 448v.exe” file in the driver kit. When the following screen
16
After confirming that “VIA PCI IDE Bus Driver”, “AGP Driver” and “VIA INF Driver” are all selected,
click on the [Next] button to start the installation. Reboot the machine when requested.
17
Open the property screen of Ethernet Controller shown with a question mark (?) on the Device
Manager screen.
Click on the [Update Driver..] button to start the “Update Device Driver Wizard”. Select the
“VIA\lan” folder in the install kit for the driver path, and continue the installation.
18
The “VIA Rhine II Fast Ethernet Adapter” is installed.
Open the property screen of the Video Controller shown with a question mark (?) on the Device
Manager screen.
19
Click on the [Update Driver..] button to start the “Update Device Driver Wizard”. Select the
“VIA\VGA\w2kxp” folder in the install kit for the driver path, and continue the installation.
20
7) Installing the USB2.0 Driver
Since USB 2.0 is supported from Windows 2000 SP4, it is necessary to install the SP4 or greater
and follow the procedure described below to use USB 2.0.
[Next] button.
Choose the “Install USB 2.0 Driver” and click on the [Next] button on the screen below. Reboot
the machine when requested.
21
When not using the SP4 or greater, install the filter driver using the following procedure.
[Next] button.
Choose the “Install VIA USB filter driver” and click on the [Next] button on the screen below.
When the installation is completed, the machine is rebooted.
22
Open the property screen of the Multimedia Audio Controller shown with a question mark (?) on
the Device Manager screen.
Click on the [Update Driver] button to start the “Update Device Driver Wizard”. Select the
23
Open the property screen of the SMK PnP TABLET shown with a question mark (?) on the Device
Manager screen.
24
“Tablet\PnPTablet\Win2kxp” folder in the install kit for the driver path, and continue the installation.
25
Open the Touch Panel Properties screen in the Control Panel. When the Touch Panel Properties
screen appears, click on the [Calibration] button and the [Execute] buttons, in order, to set the
calibration.
IMPORTANT
connected, the touch panel driver cannot be loaded properly, and calibration
cannot be set. When installing the driver, connect any of the mice and let the
machine detect the mouse.
26
10) Precautions for Use of PC Cards
When using a PC card (16 bits) under Windows 2000, it is necessary to disable COM4, as the
PC cards cannot be used by default. (When using cards supporting CardBus, this setting is
unnecessary.)
Select the [Advanced] menu of the BIOS setup menu, change the setting of the UPS\COM4 IRQ
from “IRQ11/7” to “IRQ11/None”.
Then, start Windows, open the Device Manager, and open the property screen of COM4.
Remove a check from the check box for “Use automatic settings” on the Resource screen, and
select the item which does not use the IRQ from the list of “Setting based on”. After clicking on
the [OK] button, reboot the machine when requested.
After the machine is rebooted, COM4 is disabled and shown on the Device Manager screen with
an exclamation mark (!). Instead, a PC card (16 bits) can be used.
27
4. Set up of Windows NT
1) Setting up BIOS
[Exit] Menu → Load Setup Defaults (Win NT)
After connecting a PS/2 mouse, install Windows NT 4.0 on the ST-70.
IMPORTANT
When Windows NT is installed without connecting the PS/2 mouse, the touch
panel driver cannot be installed. Be sure to connect the PS/2 mouse before
installing Windows NT.
3) Installing the Service Pack (SP)
For installing the Audio driver, SP4 or greater is required.
For installing the VGA driver, SP5 or greater is required.
28
Choose “Install”, and click on the [Next] button. When requested, reboot the machine.
29
5) Changing/Adding the Serial Port
After installing the 4 in 1 chipset software, it is necessary to properly change the settings of the all
serial ports because they are in the default status.
Select the Ports in the Control Panel, and double-click on the port to be changed. The setting
screen will appear.
When clicking on the [Advanced…] button, the Advanced setting screen will appear. Change the
settings for the Interrupt Request Line (IRQ) and Base I/O Port Address as shown in the table
below. If a desired value is not found in the scrolling text box, type in through the keyboard.
COM Port Number
COM1
COM2
COM3
COM4
Base I/O Port Address
Interrupt Request Line (IRQ)
3F8
4
2F8
3
3E8
10
2E8
7
Setting values for each port
30
After setting COM1 to COM4, add COM6 (SIO2). (COM5 (SIO1) is not necessary to be added
because it is disabled for the reason of the hardware configuration.)
The setting values for COM6 are as follows.
COM Port Number
COM6
Base I/O Port Address
Interrupt Request Line (IRQ)
2F0
5
Setting values for COM 6
Select the Network in the Control Panel, and execute the Network Setup Wizard.
When the following screen appears, click on the [Select from list] button and select the “VIA\lan” in
the driver kit.
31
The “VIA Rhine Family Fast Ethernet Adapter Driver” is selected. Continue the installation.
IMPORTANT
If a LAN-related component is installed and the machine is rebooted after the
installation of the service pack, the message indicating the service is not
functioning is displayed. The following event error is recorded in the event log.
Event ID:
7001
Source:
Service control manager
Type: Error
Explanation: The Computer Browser service depends on the Server service
which failed to start because of the following error:
The device connected to the system does not function.
To clear this error, install the service pack again.
Open the Display Properties screen in the Control Panel. On this screen, click on the Settings tab,
and then click on the [Display Type] button.
32
Click on the [Change..] button, select the “VIA\VGA\NT” in the driver kit, and then, install the
“VIA\S3G CLE266”.
Open the Multimedia Properties screen in the Control Panel. .
Click on the Device tab, and then click on the [Add..] button.
Select the “VIA\Audio\74\Winnt40” folder in the driver kit, and install the “VIA AC97 Audio
controller”.
33
Open the Mouse Properties screen in the Control Panel.
Click on the General tab, and then click on the [Change..] button. Select the
“Tablet\PnPTablet\WinNT” folder in the driver kit, and install the “SMK PnP Tablet Driver”.
After rebooting the machine, click on the Start button and select Run to run the “tabcalNT.exe” file
for calibration setup.
IMPORTANT
When WindowsNT is installed without PS/2 mouse connected, the [Change]
button is disabled, causing the touch panel driver not to be installed.
34
10) Precaution for Use of PC Cards
When using a PC card under Windows NT, it is necessary to change the settings. (A PC card is
used instead of a CF.)
Select the [Advanced] menu of the BIOS setup menu, and change the settings of the “PnP/PCI
Configurations” as follows:
INT A# Assignment [11] → [15]
INT B# Assignment [11] → [15]
INT C# Assignment [11] → [15]
INT D# Assignment [11] → [15]
Change the setting of the “Integrated Peripherals” of the [Advanced] menu as follows:
On Chip IDE Channel1 [Enabled] → [Disabled]
After that, assign “11” to the IRQ used by the PC card.
When a PC card is inserted, the I/O address may conflict with other device, depending on the
PC card’s I/O address. In this case, change the I/O address of the PC card.
Example) When Symbol Technology’s wireless LAN card (LA-4121) driver is installed, the
default I/O address is ranging from 300 to 337. For the I/O addresses of TEC UPS
and drawer are:
I/O address of the UPS: 318
I/O address of the drawer: 310
As a result, the UPS and the drawer cannot be used due to the conflict. Accordingly,
it is necessary to change the I/O address of the wireless LAN card.
If a PC card, of which driver was uninstalled even just once, is inserted, Windows NT may
assign a resource to the PC card, causing other devices to be disabled. Therefore, it is
necessary to delete the currently used PC card’s key from the PC card insertion record in the
registry, and then reboot the machine.
You will find the PC card insertion record at
“HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Pcmcia\Database”.
35
Example) After uninstalling the Symbol Technology’s wireless LAN card (LA-4121) driver, if
Windows NT is started while the wireless PC card remains inserted, Windows NT
assigns IRQ10 to the wireless LAN card. To check the assigned resource, select the
PCMCIA in the Control Panel, and click on the [Properties] button on the PC Card
(PCMCIA) Devices screen.
On the Resource page, information of IRQ currently assigned to the Resource is
shown.
If IRQ10 is assigned to the wireless PC card, the touch panel cannot be used
because IRQ10 is intended for the touch panel. By deleting the Symbol Technology’s
wireless LAN card record from the PC card insertion record in the registry, the
assignment of IRQ10 is canceled.
You will find the PC card insertion record at
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Pcmcia\Database.
Delete “Symbol Technologies” from the record and reboot the machine.
36
5. Set up of Windows 98SE
1) Setting up BIOS
[Exit] Menu → Load Setup Defaults (Win98)
Then, disable the printer as follows only at the time of installation.
[Advanced] Menu → Integrated Peripherals
Change the setting of the Onboard Parallel Port from [378] to [Disabled].
Install Windows 98SE on the ST-70.
After installing the Windows98SE, restore the BIOS settings to the default.
Enter the BIOS setup menu, and select the [Exit] menu → Load Setup Defaults (Win98).
When the Device Manager is opened, an exclamation mark (!) is attached to the “VIA Bus Master
PCI IDE Controller”.
Open the VIA Bus Master PCI IDE Controller Properties screen, and then, click on the Settings
tab and set the Dual IDE Channel Settings to “Only Primary IDE Channel enabled”.
37
3) Changing the Serial Port Setting
After installing Windows 98SE, the Device Manager shows the serial port status as follows.
“Communications Port (COM5)”, the registry needs to be changed.
You will find the registry at “HKEY_LOCAL_MACHINE\Enum\ACPI\*PNP0501\00000006”.
For the Device Desc, change from “Communications Port (COM5)” to “Communications port
(COM6)”.
For the FRIENDLYNAME, change from “Communications Port (COM5)” to “Communications Port
(COM6)”.
For the PORTNAME, change from “COM5” to “COM6”.
After changed, reboot the machine.
38
39
After confirming that “VIA ATAPI Vender Support Driver”, “AGP Driver” “IRQ Routing Miniport
Driver”, and “VIA INF Driver” are all selected, click on the [Next] button to start the installation.
Reboot the machine when requested.
Since the “VIA Standard PCI to ISA Bridge” and the “VIA Standard CPU to PCI Bridge” drivers are
requested after the machine is restarted, install them onto “C:\windows”.
40
When the Device Manager is opened, an exclamation mark (!) is attached to the “VIA Bus Master
PCI IDE Controller”.
Open the VIA Bus Master PCI IDE Controller Properties screen, click on the Settings tab, and set
the Dual IDE Channel Settings to “Only Primary IDE Channel enabled”.
41
Open the property screen of Ethernet Controller shown with a question mark (?) on the Device
Manager page.
“VIA\lan” folder in the install kit for the driver path, and continue the installation.
42
The “VIA Rhine II Fast Ethernet Adapter” is installed.
Open the property screen of the Standard PCI Graphics Adapter (VGA) in the Display adapters
shown on the Device Manager page.
43
“VIA\VGA\98” folder in the install kit for the driver path, and continue the installation.
When the CD of Windows98 and the “viagfx.cat” are requested during installation, select “Skip
File”.
44
7) Installing USB 2.0 Driver
Run the “VIA\USB\Setup.exe” file in the install kit to start the installation of USB 2.0 driver.
After clicking on the [Next] button on the previous screen, choose the “Install USB 2.0 Driver” and
click on the [Next] button to finish the installation. When requested, reboot the machine.
45
Open the property screen of the Multimedia Audio Controller shown with a question mark (?) on
the Device Manager page.
46
Open the property screen of the SMK PnP TABLET shown with a question mark (?) on the Device
Manager page.
47
“Tablet\PnP Tablet\Win9x” folder in the install kit for the driver path, and continue the installation.
48
After rebooting the machine, open the Touch Panel Properties screen in the Control Panel. Click
on the Calibration tab, and then, click on the [Execute] button to set the calibration.
IMPORTANT
connected, the touch panel is not detected. When installing the driver, connect
any of the mice and let the machine detect the touch panel.
Do not check the “Beep when touched” checkbox on the Sound tab in the
Control Panel. This function is not available on Windows 98. (Windows 98
cannot keep the sound constant.)
10) Precaution for Use of PC Cards
When using a PC card under Windows 98, it is necessary to change the BIOS settings. (A PC
card is used instead of USB on the monitor and USB 2.0.)
Select the [Advanced] menu of the BIOS setup menu, and change the settings of the “PnP/PCI
Configurations” as follows:
INT A# Assignment [11] → [15]
INT B# Assignment [11] → [15]
INT C# Assignment [11] → [15]
INT D# Assignment [11] → [15]
Change the “Integrated Peripherals” of the [Advanced] menu as follows:
USB 2.0 Support [Enabled] → [Disabled]
On Chip USB Controller [1&2 USB Port] → [1 USB Port]
49
11) Precaution for Use of CF
The CF (Secondary IDE Channel) cannot be used by default.
When using a CF under Windows 98, it is necessary to change the BIOS settings.
(A CF card is used instead of a printer.)
Select the [Advanced] menu of the BIOS setup menu, and change the settings of the “Integrated
Peripherals” as follows:
On Chip IDE Channel 1 [Disabled] → [Enabled]
Onboard Parallel Port [378] → [Disabled]
After starting Windows 98, open the VIA Bus Master PCI IDE Controller Properties screen by
selecting the “Hard disk Controllers” on the Device Manager page. Click on the Settings tab,
and set the Dual IDE Channel Settings to “Default”.

Windows Setup Guide for ST-70

Transcription

Similar documents

Teen Driver Contract

EFAS Wandtafel Mitte

nEar05 eXperience

Q: I am not able to install the AVermedia driver for

USB2.0 IRDA Adapter

2007 CADILLAC STS-V

driver protection screen

QuickDocs - HYPE Systems Inc.

User Manual