300 STERN DRIVE COMPONENTS

Transcription

STERN DRIVE COMPONENTS
TRANSOM SEAL KITS
Transom seal kit w/ exhaust bellows,
All #1, R, MR, Alpha 1983 - 1990
Transom seal kit, for 1, R, MR, Alpha 1
w/ exhaust tube 1983 - 1990
Complete kit
18-2601-1
Part#
O.E.#
Description:
18-2619-1
---
OUTDRIVE GASKET SET
18-2100
30-60794A4
GIMBAL BEARING
18-2161
45518A2
SHIFT ARM
18-2751
60932A4
U-JOINT BELLOWS
18-2750
32734A3, 18654A1
EXHAUST BELLOWS
18-2753-1
74639
SHIFT CABLE BELLOWS
18-7314
---
STAINLESS HOSE CLAMP
18-7315
---
STAINLESS HOSE CLAMP
Transom seal kit, for Alpha 1 Gen. II
Complete kit
18-8206
Complete kit
18-8205
Part#
O.E.#
Description:
18-2100
30-60794a4
GIMBAL BEARING
18-2751
60932A4
U-JOINT BELLOWS
18-2760
78458A1
EXHAUST TUBE
18-3601
32-32461
WATER INTAKE HOSE
18-3602
32-41725-33
WATER INTAKE HOSE
18-2743
2794996-2
DRIVE SHAFT HOUSING TO
BELL HOUSING GASKET
18-2840
27-35982
BELL HOUSING GASKET
18-7153
25-25439
“O”-RING
18-7117
25-35027
“O”-RING
18-7310
---
HOSE CLAMP
18-7170
25-33504
“O”-RING
18-7312
---
HOSE CLAMP
18-2753-1
74639
SHIFT CABLE BELLOWS
18-7321
54-38863
BELLOWS CLAMP
Transom seal kit, for all Bravos 1982 & up
Part#
O.E.#
Description:
18-3602
32-41725-33
Water intake hose
18-7310
Hose clamp
18-7312
Hose clamp
18-2753-1
74639
Shift cable bellows
18-7321
54-38863
Bellows clamp
18-2100
30-60794A4
Gimbal bearing
18-2743
27-94996-2
Drive shaft housing to bell housing
gasket
18-2840
27-35982
Bell housing gasket
18-7153
25-25439
O-ring
18-7170
25-33504
O-ring
18-7117
25-35027
O-ring
18-2750
18654A1,
32734A3
18-2747
300
Complete kit
18-8212
816431A1
Part#
O.E.#
Description:
18-2753-1
74639
SHIFT CABLE BELLOW
18-2100
30-60794A4
GIMBAL BEARING
18-2756
86840A3
U-JOINT BELLOWS
18-2750
32734A3
EXHAUST BELLOWS
18-2760
78458A1
EXHAUST TUBE
Exhaust bellows
18-3603
32-43437
WATER HOSE
Drive bellows
18-2615
16755A1
OUTDRIVE MOUNTING KIT
Lighthouse Marine Supply I “saving boater’s weekends everywhere”
BELLOWS, EXHAUST TUBES, & LOWER UNIT GEAR SETS
U-JOINT BELLOWS
Part#
18-2751
Description:
All #1 units w/ ridge s/n 3469428 & up, replaces
60932A4, includes 18-7316 clamp
U-JOINT BELLOWS
Part#
18-2756
Description:
for all Bravo units, replaces
86840A3
SHIFT CABLE BELLOWS
Part#
18-2753-2
Description:
for all #1, #2 units, Alpha, Bravo I, II, III, replaces
74639, includes 18-7321 clamp
Part#
18-2200
Description:
Lower unit gear set, replaces 43-96084A4, 888 s/n
3106717 & up, #1 units s/n 3469428 & up except MR/
Alpha units, which have no pre load pin in the top of the
drive shaft
U-JOINT BELLOWS
Part#
18-2747
Description:
for Alpha 1 Gen II, replaces 16431A1
EXHAUST BELLOWS
Part#
18-2750
Description:
for all #1 units, Gen II, TRS, & Bravo I, II, III, replaces
32734A3, 18654A1, includes 18-7314 clamp
EXHAUST TUBE
Part#
18-2760
Description:
replaces 78458A1, for #1,
Bravo I, II, III, includes
18-7314 clamp
Part#
18-2206-1
Description:
Lower unit gear set, replaces 43-17064A3, 43-42934,
43-17064A2, When installing new style 18-2206/AP#
2352 “Tractor Gears” in Alpha One Gear Housing
(F680153 & BELOW) with a 3.4985 - 3.5000 forward
bearing bore use Forward Bearing 18-1173. Alpha One
Gear Housing (F680154 & UP) with a 3.2635/ 3.2650
forward bearing bore, use Forward Bearing
18-1156/AP# 1906
order toll free: 1-800-382-9335 I WWW.PARTMAN.COM I 24 hr. fax: 631-722-5719
301
UPPER UNIT DRIVE GEARS, GEAR SETS, & DRIVE SHAFT
Replaces 43-45814A5, for 6 cyl.
Inline s/n K999999 & below
Replaces 43-18410A2, 43-18411A2, includes
(1) 18-1142, for most V8 drives & Gen II
s/n K999999 & below
Part #
Ratio
18-2201
1.5:1
Drive Gear Driven Gear
22 teeth
20 teeth
Replaces 43-853643A2, for Alpha I Gen II
1998 & up, 0L00040 & up
Part #
Ratio
18-6353
1.81
17 teeth
19 teeth
Part #
Ratio
18-2203
1.65:1
Ratio
18-2205
1.98:1
24 teeth
24 teeth
Replaces 43-75325A3, for V6 & 470/485
4 cyl. etc. & Gen II s/n K999999 & below
Part #
Ratio
18-2204
1.84:1
Replaces 43-55778A3, for 120/140 s/n
2791957 & up * Gen II s/n 999999 & below
Part #
17 teeth
19 teeth
Replaces 43-803116T1, for
most V8 drives, ratio 1.5:1
20 teeth
24 teeth
Complete Kit Part# 18-2256
Part#
Part#
BJM59829
Description:
Drive Shaft, Replaces 814819A2, for all #1, R/MR/Alpha
Gen II drives w/ V6 & V8 powerheads, In-line engines not
included
302
O.E.#
Description:
18-2201 43-18410A2 UPPER UNIT GEAR SET
18-2648 26-32511A2 SEAL KIT
18-1160
31-35988A2 BEARING KIT
18-1165
31-61100A1 BEARING
18-1142
31-35990A1 BEARING
UPPER & LOWER UNIT SEAL KITS
Part#
18-2614
Description:
1982 & Older Mercruisers, outdrive gasket set
Part#
18-2615
Description:
All Bravo’s, outdrive mounting kit
Part#
18-2648
Description:
Upper gear housing seal kit, s/n 1684188 & up, for
#1 units (including alpha), replaces 26-32511A1
Part#
18-2644
Description:
Upper unit seal kit, replaces 26-88397A1, for
Alpha I Gen. II
Part#
18-2643
Description:
Upper unit seal kit, replaces 26-16709A2, for
Bravo Blackhawk
Part#
18-2619-1
Description:
1983-newer, R/MR/Alpha & Alpha gen II, w/
oil reservoir, outdrive gasket set
Part#
18-2620
Description:
TR, TRS, Gasket set
Part#
18-2652
Description:
Lower gear housing seal kit, s/n 1684188 & up, for
#1 units (including alpha), replaces 26-33144A2
Part#
18-2646-1
Description:
Upper unit seal kit, replaces 26-816575A3
Part#
18-2645
Description:
Lower unit seal kit, replaces 26-76868A2, for
Bravo I, II, III
303
COMPLETE LOWER UNIT WATER PUMP KITS & COMPONENTS
IMPELLER
Part#
18-3017
Description:
Replaces 47-89984, 47-89984T4,
47-30221, & 47-65960, for all #1, R,
MR, Alpha units
IMPELLER
Part#
18-3056
Description:
Replaces 47-43026-2, for Alpha I
Gen II, Mercuiser Vazer
IMPELLER
IMPELLER KIT
Part#
18-3016-1
Description:
W/ gasket & plug, replaces 47-862232A2,
for Late model Bravo & High performance,
includes 350 mag, 4.3L, 496 Mag, 5.0L,
8.1S & MX 6.2L, impeller drive has (2) flat
spots
Part#
18-3217
Description:
Without base or housing, for #1units
thru S/N D494568
WATER PUMP KIT
Part#
18-3317
Description:
For units with preload pin in lower
unit drive shaft, replaces Mercruiser
#46-96148A8
WATER PUMP KIT
Part#
18-3147
Description:
Replaces 817275T4, for Gen II lower units
304
WATER PUMP KIT
Part#
18-3320
Description:
For units with no preload pin in lower
unit drive shaft
WATER PUMP KIT
Part#
18-3224
Description:
Replaces 47-59362T6, for Bravo
(plastic 1 piece body)
IMPELLER
Part#
18-3087
Description:
Replaces 47-59362 & 47-59362T,
impeller drive has single flat spot
WATER PUMP KIT
Part#
18-3517
Description:
Without base, Replaces 46-96148A5 &
46-60367A1
IMPELLER REPAIR KIT
Part#
18-3214
Description:
Replaces 47-40326T6, T8, & T11, for
Alpha I Gen II, Mercuiser Vazer
WATER PUMP KIT
Part#
18-3150
Description:
Replaces 46-807151A14, for Bravo
LOWER UNIT SHIFT CABLES & TRIM SENDER / LIMIT KIT
MERCRUISER ALPHA I & ALPHA I GEN II STERN DRIVE
SHIFT CABLES 1983 - PRESENT
Part#
18-2190
Description:
Replaces 19543A4, A10, for Mercruiser 1 drives, S/N
6225577& up, for AFT installation into bell housing, for
use in applications using core wire with armored strand
construction, no support tube, 63” L
Part#
18-2162
Description:
Shift cable slide & screw,
replaces 33981T
Part#
18-2603
Description:
Replaces 19543T-1, for Alpha I Gen II drives,
complete kit, includes items below:
Part#
O.E.M.
Description:
18-2619-1 27-94996A1 Outdrive gasket set
18-2753-1 74639
Shift cable bellows
18-2190
19543A4
Shift cable assembly
18-2743
27-94996-2
Drive shaft housing to bell
housing gasket
MERCRUISER BRAVO LOWER SHIFT CABLE
Part#
18-2145
Description:
Shift cable, replaces 815471A3, & A6
MERCRUISER TRIM
SENDER / LIMIT KIT
Part#
18-2604
Description:
Replaces 815471T1, Bravo drives, complete
kit, includes items below:
Part#
O.E.M.
Description:
18-2145
815471A3
Bravo shift cable
18-2149
43433
Shift cable end kit
18-2753-1 74639
Shift cable bellows
18-2615
Outdrive gasket set
----
SHIFT SHAFT
HOUSING BUSHING
Part#
18-7633
Description:
replaces 805320A03, fits MC-1, R, MR, Alpha,
Alpha Gen II, & Bravo drives
Part#
18-2154
Description:
Replaces 23-30617A2,
Mercruiser & Alpha
SHIFT ROD
BUSHING ASSEMBLY
Part#
18-2353
Description:
Replaces 23-815921A21,
for Alpha I, Gen II
305
YOKE ASSEMBLIES & COMPONENTS
CENTER SOCKET
YOKE
Part#
18-2125
Description:
Replaces 46020T, fits all #1/Alpha
units, S/N 1684188 - OK999999
Part#
18-2128
Description:
Replaces 39383T & 343831, Fits
Rockwell, IA/IB/IC & EZ, MC-1, MR,
Alpha I Gen II, Bravo MCII & TS
Part#
18-6400
Description:
Replaces 12784, for Bravo
OM111207 & below, & Blackhawk
Part#
18-6403
Description:
Replaces 865492T & 864282T,
fits Alpha I Gen II OL949779 & up,
Bravo 0M111208 & up GKN style,
Mercuiser Vazer
YOKE ASSEMBLY
Part#
18-9218
Description:
Replaces 814819A2, for all #1,
R/MR/Alpha Gen II OK999999 &
below, 1971-97
306
CARRIER NUT WASHER
Part#
18-3712
Description:
Replaces 12-45810
Part#
18-3713
Description:
Replaces 11-22339, 5/8” - 18
CENTER SOCKET
YOKE
Part#
18-3752
Description:
Replaces 816811-1 &
8168112, for Merc #1 &
Alpha Upper input yoke
Part#
18-2146
Description:
Replaces 59830A1 & 59830A7, fits
all #1, R, MR, Alpha I, Alpha I Gen II,
Bravo & Blackhawk
LOCK NUT
YOKE
RETAINING NUT
YOKE
Part#
18-6404
Description:
Replaces 865503T, fits Alpha I Gen II
0L949779 & up, GKN style
YOKE
Part#
18-6405
Description:
Replaces 865491A01 & 864281A01,
fits Alpha I gen II 0L949779 & up,
GKN style, mercruiser vazer
YOKE ASSEMBLY
Part#
18-6402
Description:
Replaces 864281A2, for Alpha I
Gen II 1998 & up, OL100040 & up,
GKN style, mercruiser Vazer
CARRIER OIL
SEAL ASSEMBLY
Part#
18-0577
Description:
Replaces 66081A2, for Merc
#1 & Alpha Upper input yoke
YOKE ASSEMBLY
Part#
18-6401
Description:
Replaces 12784A10 & 864244A2,
for Bravo I, II, III OB664190 & up,
1998-05
SEAL ONLY
Part#
18-2003
Description:
Replaces 26-823894 &
26-68493, for Merc #1 &
Alpha Upper input yoke
SPLINE GREASE
Part#
18-9200
Description:
14 ounce tube , Specialty
grease used in the assembly
of engine yokes and couplers
U-JOINTS, GIMBAL BEARINGS, SHIFT SHAFTS, & BUSHING KITS
U-JOINT
Part#
18-2104
Description:
Replaces 75832A2 & 75832T, includes
straight & 90º grease fittings, Rockwell,
fits all #1 & Alpha I units S/N 1684188 B418818, Also TR/TRS & II SSM
U-JOINT
Part#
18-6406
Description:
Replaces 865496A01 & 865493A01,
GKN new style with external clips, fits
Alpha I Gen II 0L949779 & up, Bravo
0M111208 & up, mercruiser Vazer
HINGE PIN
Part#
18-1706
Description:
Replaces 10-86801, for gimbal
housing, fits Bravo all models
SHIFT SHAFT
U-JOINT
Part#
18-2174
Description:
Replaces 75832A3, 758321, & 75832T1,
includes straight & 90º grease fittings,
Rockwell, fits Alpha I units S/N B418819 &
above, also fits Alpha I SS & Bravo
U-JOINT
Part#
18-1711
Description:
Replaces 862132T, for Bravo I, II, III (all
ratios), Bravo One X, Two X, Three X (all
ratios), Bravo I XR/XZ (all ratios) Bravo I
XR Sportmaster (all ratios)
HEAVY DUTY
GIMBAL BEARING
Part#
18-2100
Description:
Replaces 30-60794A4 (link belt), fits
Merc 120-140hp, (2791957-6225576)
with gimbal trim sender, 165hp (2763442
& up), 225S (3856268-4200499), 228hp
(4782330 & up), 233hp (4200500 & up),
250hp (4791300 & up)
U-JOINT
Part#
18-2097
Description:
Permalube, replaces 805536A2, for
Gen II F680000 & up
HINGE PIN
Part#
18-1705
Description:
Replaces 77123, with grease port, for
gimbal housing, fits Alpha all models
GIMBAL BEARING
Part#
18-21005
Description:
Replaces 30-862540A3, fits all
Bravos, Alpha I Gen II 1998 & up
UPPER SHIFT SHAFT
SHIFT ARM
Part#
18-2322
Description:
Replaces 621041, for I, & Alpha I
DRIVE BEARING KIT
Part#
18-1160
Description:
Replaces 31-35988A2 & 31-35988A12
Part#
18-2169
Description:
Replaces 45589A3
BELL HOUSING
BUSHING KIT
Part#
18-2622
Description:
Replaces 23-805041A2
Part#
18-3749
Description:
Replaces 816685, for Alpha Gen II
1991-1998
BELL HOUSING
BUSHING KIT
Part#
18-3760
Description:
Replaces 23-806036A1, for Gen II
S/N F680000 & up
307
(A1) I / I-R / MR / ALPHA ONE UPPER DRIVE HOUSING
Part#
18-3219
Description:
Replaces 42724A3, for Merc I, 1A, 1B, 1C,
1CEZ, 120, 140, 160, 165, 888, 898, 228,
225-S, 233, 250, 260, 470, 485, R, ME, Alpha
18-3229 BOLT, replaces 10-28668
308
(A1) I / I-R / MR / ALPHA ONE UPPER DRIVE HOUSING
309
(A2) ALPHA ONE / GEN II UPPER DRIVE HOUSING
310
(A2) ALPHA ONE / GEN II UPPER DRIVE HOUSING
311
(A3) #1-R LOWER GEAR HOUSING
312
(A3) #1-R LOWER GEAR HOUSING
313
(A4) MR / ALPHA LOWER GEAR HOUSING
314
(A4) MR / ALPHA LOWER GEAR HOUSING
315
(A5) GENERATION II LOWER GEAR HOUSING
316
(A5) GENERATION II LOWER GEAR HOUSING
317
ALPHA I GEN II 1983 TO PRESENT GIMBAL HOUSING
35
17B
22
23
55989A8
BOLT KIT W/
ANODE “GEN I ONLY”
ANODE ONLY LLM55989
Ref#
Part#
8
MAL9-76230
2688416
Gimbal bearing seal
10
18-2100
3060794A4
Gimbal bearing assembly complete
41802
O ring - Exhaust pipe
13A
65533A1
1983 - 1990
13B
43713
1991 & newer
32416721
3/4” Plastic Tube
16A
23416751
Bushing, 3/4”, “FOR GEN. I ONLY”
16B
238165991
Bushing, 3/4”, “FOR GEN. II ONLY”
11
15
Description:
17A
41673
Plate for tube, 3/4”
17B
818304A1
Block off plate Use gasket 27818305
22
55989A8
Bolt kit w/ anode, “FOR GEN. I ONLY”
22A
1032620
Bolt “ FOR GEN. II ONLY”
23
LLM55989
26, 27, 28
18-2753-2
31
318
OEM#
18-0388
Anode only
74639A2
Shift cable belows & clamp
27988231
Gasket, Hydraulic connector
32
98825A4
Hydraulic Connector
35
861776A2
Block off plate, “Y” pipe w/ bolts & lock washers
BRAVO GIMBAL HOUSING
Part#
18-9031
Description:
Bellows Adhesive
Replaces 92-86166, 2 oz.
Ref#
Part#
Description:
9
2688416
Grease seal
10
18-2100
Gimbal bearing
12
41802
Seal to Exhaust “Y” pipe
14
43713
Seal to transom
15
3243437
Water Hose
16
41674
Insert, water hose
16A
18-9844
Tool for installing tapered insert
20
2243828
Water Connector
21
27441081
Gasket connector
24, 25, 26 18-2753-2
Bellows shift cable w/ clamps
29
27988231
Gasket manifold
30
98825A4
Manifold Hydrualic hoses
319
ALPHA ONE 1980 - 1990 BELL HOUSING
6C
UPDATED BELL HOUSING
BUSHING KIT
Fits all MC 1 and up and
ALPHA Bell housing
Replaces Mercury
23-805041A2, 18-2622
A
19B
18-2760
Ref#
2
2A
2
Part#
Description:
18-2619-1
Gasket kit, mount drive 1983 & newer
18-2614
Gasket kit, mount drive pre 1982
6A
2645587
Oil seal, bell housing, 1978 - 1982
6B
268164641
Oil seal, bell housing, 1983 - 1990
23-805041A2
Oil seal, bell housing, update kit
1235935
Bell housing stud washer
6C
18-2622
12
13
BJM11134391
14
18-2751
60932A4
Bellows / U-joint assembly
17A
18-3601
3232461
Water Hose 5/8” I.D.
Nut, bell housing stud
17B
18-3602
324172533
Water Hose 3/4” I.D.
19A
18-2750
18654A1
Exhaust bellows assembly
19B
18-2760
21
18-2169
45589A3
Shaft assembly, shift, upper
22
18-2322
621041
Shift shaft, intermediate
25
18-2161
45518A3
Lever assembly, upper shift shaft
1239116
Washer, Nylong, shift shaft
1045590
Screw, upper shift shaft 11/16”
26
27
320
OEM#
18-2170
18-2619-1
*Exhaust tube (optional)
ALPHA I GEN II 1991 TO PRESENT BELL HOUSING
#19B
18-2760
A
2
Ref#
2
6A
Part#
18-2619-1
18-2622
6B
9
13
OEM#
18-2747
16
Description:
Outdrive mounting kit, includes 2, 7, 8, 34
23805041A2
Bushing & oil seal kit s/n F0094774 & below
23806036A1
Bushing & oil seal kit s/n F094775 & up
1272498
Washer
816431A1
Bellows, u joint
816607
Sleeve
3/4” water hose
17
18-3602
324172533
18
620-012
54815504412 Clamp, water hose
19A
18-2750
18654A1
19B
18-2760
22
18-2161
23
24
25
18-2170
18-2619-1
Bellows, exhaust
*Exhaust tube (optional)
45518A2
Shift Arm
1239116
Washer, nylon shift
1045590
Screw, shift arm
816685
Shift shaft upper
321
BRAVO I, II, III BELL HOUSING
#12B, 18-2760
18-2615
Ref#
Part#
2
12806241
4
Description:
Washer
41674
Insert, water inlet
4A
18-9844
Tool for installing tapered insert
6
1235935
Washer
7
BJM11134391
8
18-2756
11
322
OEM#
Nut, locking
86840A05
Bellows, u joint
862209
Sleeve, u joint bellows
12A
18-2750
18654A1
Bellows exhaust
12B
18-2760
78458A1
*Tube exhuast, optional
R / MR & ALPHA ONE 1972 - 1982 TRIM CYLINDERS & HYDRAULIC HOSES
15
14
Ref#
Part#
Description:
1
18-2126
Tubing
2
2249718
Nut
3
18-2108
Trim hose
4
18-2109
Trim hose
5
18-2103
Trim hose, requires 2 hoses each side, 4 total
6
18-2142
Trim Cylinder
7
GLM21310
Front anchor pin kit w/ hardware
8
1245737
Washer
9
18-2701
Bushing
10
12-46765
Washer
11
1182671013
Lock nut
12
GLM21390
Rear anchor pin kit w/ hardware
13
18-4252
Spring
14
18-2291
Trim cylinder seal kit
15
18-2148
Housing only, trim cylinder
323
R / MR / ALPHA 1983 - 1990 TRIM CYLINDERS & HYDRAULIC HOSES
PORT
STARBOARD
5A, 18-2426
Replaces 98703A3, casting # on
cylinder 98703, length 15-9/16”
use hose 18-2137 (3299903)
4A, 18-2427
use hose 18-2136 (3299902)
18-2372
Trim cylinder end cap, replaces
88035, fits 18-2427 & 18-2426
cylinders, 2.081 O.D.
5B, 18-2421
use hose 18-2115 (32999031)
4B, 18-2420
use hose 18-2114 (32999021)
18-2373
Trim cylinder end cap, replaces
806191T, fits 18-2420 & 18-2421
cylinders, 1.89 O.D.
Description:
Ref#
Part#
18-2649
Seal kit, contains o-rings,
washers, & retaining rings
Description:
Ref#
Part#
1
18-2435 (black)
Hydraulic hose, connector to pump
9
1085486
Screw
2
18-2436 (gray)
Hydraulic hose, connector to pump
10
18-2462
Front anchor pin w/ hardware
3
18-2116
Hydraulic hose, trim cyl. to connector
11
12-85058
Front pin washer
5A
18-2426
Port trim cylinder replaces (98703A3)
12, 17
18-2702-1
Rubber bushing
5B
18-2421
Port trim cylinder replaces (14035A3)
13A
12-85057
Washer, front pin 3/8-24 threads
4A
18-2427
Starboard trim cylinder replaces (98704A3)
13B
12-44163
Washer, front pin 7/16-20 threads
45B
18-2420
Starboard trim cylinder replaces (14034A3)
14A, 19
11862903
Nut, front pin 3/8-24 threads
6A
18-2136
Starboard trim hose, casting #98704
14B, 19
BJM11134391
Nut, front pin 7/16-20 threads
6B
18-2114
Starboard trim hose, casting #14034
15
18-2463
rear pin kit w/ hardware
7A
18-2137
Port trim hose, casting #98703
20
MAL9-77200
Trim cylinder Front /Rear caps
7B
18-2115
Port trim hose, casting #14035
85060
Clamping plate, trim cylinder hose
8
324
ALPHA I GEN II 1991 & NEWER TRIM CYLINDERS & HYDRAULIC HOSES
10 A/B
18-2649
Ref#
Part#
Description:
Ref#
Part#
Description:
1
18-2435
Hose connector to pump, (black)
8
85060
Plate
2
18-2436
Hose connector to pump, (gray)
9
1085486
Screw 1/4-20 x 3/8”
3
18-2116
Hydraulic hose, cylinder to connector
10A
18-2395
Pin only
4
18-2423
Starboard trim cylinder
10B
MAL9-77101
Pin kit w/ hardware
5
18-2422
Port trim cylinder
11
18-2341
Bushing
ZIN806189
Anode assembly
12
12815952
Washer
10806290
Screw #10-32x5/8”
13
18-2345
E ring
6
18-2114
Starboard trim cylinder hose
14
19815951
Cap
7
18-2115
Port trim cylinder hose
15
22808727
Adapter with screen
5A
5B
325
BRAVO I, II, III TRIM CYLINDERS & HYDRAULIC HOSES
20 A/B
18-2649
Ref#
Part#
Ref#
Description:
Part#
Description:
11
85060
Plate
1A
18-2435
Hydraulic hose, 32-861127 (black)
12
1085486
Screw, .250-20 x .375
1B
32865384001
Hydraulic hose, quick connect (black)
13
1744167A1
Front anchor pin
22865410001
Fitting, female quick connect
14
18-4289
Retaining ring
3A
18-2436
Hydraulic hose, 32-861128 (gray)
15, 21
1244164
Washer
3B
32865385001
Hydraulic hose, quick connect (gray)
16, 22
18-4288
Bushing
2/4
22865411001
Fitting, male quick connect
17, 23
1244163
Washer
1134933
Nut, .437-20
2
5
18-2116
Hose, trim cylinder to connector
18, 24
6
18-2425
Trim cylinder, starboard
19, 25
1914842
Cap
7
18-2424
Trim cylinder, port
20A
18-2396
Rear anchor pin
8
ZIN806190
Anode assembly
20B
GLM21910
Pin kit, includes hardware
9
10806290
Screw, #10-32 x 625
26
18-2136
Starboard trim cylinder hose
10
1369432
Lock washer
27
18-2137
Port Trim cylinder hose
326
POWER STEERING CYLINDER R / MR / ALPHA I S/N 0F680000 THRU 0K999999
“OLD STYLE CYLINDER” 57969A12
3-
2-
“NEW ONE PIECE
STYLE CYLINDER”
865383A02
806034A2 KIT
Ref#
Part#
Description:
1
57969A12
Boosting Cylinder “NLA” use 80604A2 kit
2
3292054
Extending tube
3
3292055
Retracting tube
4
806034A2
1983 - 1990 Power steering cylinder kit with updated hoses from power steering pump & oil cooler
5
865383A02
1993 & up Power steering cylinder
10
816458A1
Valve, “NLA” use 806034A2 kit
327
MERCRUISER SPECIAL INSTALLATION TOOLS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Ref#
Part#
O.E.M.#
Description:
1
18-9816
91-30366T1
Mandrel, use with 18-9821 & 18-9835
2
18-9821
91-32325T
Driver, installs gimble bearing
3
18-9835
91-37323
Driver rod, use with 18-9816 & 18-9821
4
18-9817
91-31107T
Shift shaft bushing tool
5
18-9847
91-45497A1
Exhaust Bellows expander tool
6
18-9858
91-61069
Bearing carrier retainer wrench, lower unit
7
18-9861
91-78310
Hinge pin tool
8
18-9803
91-17256
Bearing retainer wrench, upper gear hosuing
9
18-9870
91-818162
Installs aluminum sleeve in u-joint bellows, Bravo &
Alpha Gen. II
10
18-9806E
91-12037
Shift cable tool, removes & installs shift cable
11
18-9810
91-17262A1
Shift cable anchor adjustment tool, all Bravo
12
18-9844
91-443579
Installs tapered insert Bravo water inlet hose
13
18-4459
91-821887A1, 91-859046Q4 Prop wrench
14
18-4442
15
18-9031
16
BJMGBP-1-PL
17
328
Engine alignment tool, for all MC-I, R-MR, Alpha I, &
Alpha I Gen. II
92-86166
Bellows adhesive
Gimbal puller
91-896661
Fuel filter tool
OMC COBRA BELLOWS & SHIFT CABLES
TRANSOM RESEAL KIT COBRA’S
WITHOUT CONE CLUTCH
TRANSOM RESEAL KIT SX
COBRA’S WITH CONE CLUTCH
Complete Kit
18-2771
Part#
O.E.M.#
18-2613
---
18-2765
18-2764
Description:
Part#
O.E.M.#
Description:
18-2100
3853807
Gimbal bearing
Exhaust bellows
18-2765
3854127
Bellows
3850426-2
Bellows
Outdrive gasket set
983973, 987467 U-Joint bellows
914036
Complete Kit
18-2772-1
18-2763
911826
Shift cable bellows
18-1074
18-2100
983937
Gimbal bearing
18-2996
18-7315
---
Hose clamp
18-7315
Part#
18-2245-1
Description:
Shift cable Replaces 987661,
986654, for 1988 - 1993 OMC
Cobra except King without cone
clutch
Part#
18-2763
Description:
Shift cable bellows, replaces
911826, fits all Cobras
3852560, 911823 Seal
Part#
18-2246
Description:
Shift cable Replaces 987678, for
King Cobra’s
Part#
18-2764
Description:
Exhaust bellows, replaces 914036,
fits all Cobras
912628 - Hose clamp, not included
912992 - Snap ring, , not included
853012-3
Hose clamp
Part#
911830
Description:
Water inlet hose for OMC Cobra
912627 - Hose clamp, 2 req.
Part#
18-2765
Description:
U-Joints bellows, replaces 983973,
987467, fits all Cobras
912677 - Hose clamp, , not included
329
OMC COBRA U-JOINTS, BEARINGS, & SEAL KITS
COBRA OUTDRIVE GASKET KIT
Replaces 508105
COBRA SX DRIVE GASKET KIT
Complete Kit
18-2613
Part#
O.E.M.#
Description:
18-2918
911836
Outdrive gasket
18-2996
911823
Outdrive seal
18-7153
911851
O-ring
Complete Kit
18-2699
Part#
18-7153
911851
O-ring
911823
Outdrive seal
HEAVY DUTY U-JOINTS
Part#
18-2104
Description:
Replaces 912214 & 915716,
fits Cobra drives 1986-89,
includes straight & 90º fittings
Part#
18-2768
Description:
Replaces 909527, fits
1978 - 1986 - ALL
SHAFT & STUB ASSEMBLY
Part#
18-6399
Description:
Replaces 984264, for Cobra 232,
302 (1986-90), 252 (1986), 262, 350,
460 (1989), 432, 434, 502 (1986-92),
504 (1986-1988), 574 (1986-92), 584
(1989-93) & 754 (1987-88)
UNIVERSAL YOKE
Part#
18-2146
Description:
Replaces 912212 & 3850815, for
ALL Cobra’s 1986 & up
Part#
18-2174
Description:
Replaces 915717 & 3850812,
fits Cobra 7 King Cobra
drives 1990 & above includes
straight & 90º fittings
U-JOINT ASSEMBLY
U-JOINT ASSEMBLY
Part#
18-2338
Description:
Replaces 983880, for 1986 - 93
OMC Cobra
Part#
18-2339
Description:
Replaces 3852384, fits ALL Cobra
1994 & up except king Cobra
CENTER SOCKET
Part#
18-2128
Description:
Replaces 912213 & 3850813, fits
ALL Cobra’s
LINK BELT HEAVY DUTY GIMBAL BEARING
Part#
18-2100
Description:
Replaces 983937, fits ALL
Cobra & King Cobra drives
330
Description:
18-2996
TRANSOM SEALS
Part#
18-2767
Description:
Replaces 313080, fits
1973 - 1977 120hp & up
O.E.M.#
STUB SHAFT
Part#
18-2377
Description:
Replaces 3850814, fits ALL Cobra
1994 & up except King Cobra
TRIM SENDER
Part#
18-7634
Description:
Replaces 984748,
fits ALL Cobra
OMC COBRA IMPELLER KITS, ENGINE COUPLERS, & TRANSOM SEALS
IMPELLER REPAIR KIT
Replaces 984461
IMPELLERS
Complete Kit
MAL9-45285
Part#
O.E.M.#
18-2541
911704
O-ring
18-2916
911702
Water pump housing gasket
18-3058
983895 Impeller
18-3121
911703
Impeller plate
18-3145
911844
Pump Liner
Part#
18-3086
Description:
Replaces 379475 &
777130, fits Stringer
drives 1964-1986
Part#
18-3058
Description:
Replaces 983895,
fits Cobra
Description:
IMPELLER REPAIR KIT
Replaces 983218, 1964 - 1986 EXCEPT COBRA
IMPELLER REPAIR KIT
1964 - 1986 EXCEPT COBRA
Complete Kit
18-3386
Complete Kit
18-3286
Part#
O.E.M.#
Description:
18-7135
310584
O-ring
18-3141
313176
Plate
18-7129
314491
O-ring
18-3111
907774
Rubber seal
18-3086
379475
Impeller
18-7158
310585, 310967
Part#
O.E.M.#
18-7135
310584
O-ring
18-3141
313176
Plate
18-7129
314491
O-ring
18-3086
379475
Impeller
18-3111
907774
Rubber seal
18-3119
983298
Impeller housing
18-7158
O-ring
BALL GEAR KIT
1973 - 1986
Description:
310585, 310967
O-ring
ENGINE COUPLERS
1
2
4
3
Complete Kit 18-2178
Part#
O.E.M.# Description:
18-7121
308621
O-ring
18-4251
908064
Plug
18-2176
908063
Ball gear
18-2177
908069
Ball gear
18-3725
908064
Locknut
18-7401
908383
O-ring
18-2071
981195
Oil seal
18-2072
981196
Oil seal
Ref#
Part#
Description:
Replaces 3853962, 983902, & 986338, fits 2.5L
1986, 3.0L 1986-90, 4.3, 5.0, & 5.7L 1986, KW &
KWB suffix only, 7.4L 1990-98, 8.2L 1992-93, 1998
1
18-21751
2
18-21752-1
3
18-21753
Replaces 3853862, fits 5.0 & 5.8L 1989-96
4
18-21755
Replaces 984629, 2.3L Cobra
Replaces 3858437, 984290, 986120, & 3853917,
fits 4.3L 1986-98, 5.0L 1986-88, 1998, 5.7L 1986-92,
1994, 1996-98
331
OMC COBRA UPPER & LOWER UNIT SEAL KITS & POWER TRIM HOSES
LOWER UNIT SEAL KIT
UPPER UNIT SEAL KIT
Part#
18-2673
Description:
Replaces 984459, 986364, & 987603, for ALL Cobra
1986 - 1989
LOWER UNIT SEAL KIT
Part#
18-2672
Description:
Replaces 984458, 985613, &
439967, for ALL V6 & V8 Cobra’s
GEARCASE SEAL KIT
Part#
18-2791
Description:
Replaces 987251 & 3850597, fits 3.0,
4.3, & 5.0L 1994, 3.2L 1992-1993,
5.7L 1992-1994, 7.4L 1992-1995, &
8.2L 1992-1993
POWER TRIM HOSE
Part#
18-2437
Description:
Replaces 986144 & 3853921, for King Cobra 1990-1994,
pump to manifold, down
POWER TRIM HOSE
Part#
18-2439
Description:
manifold to cylinder, starboard down
332
Part#
18-2671
Description:
Replaces 985612, for ALL 4 cyl. Cobra 1986 - 1989
LOWER UNIT SEAL KIT
Part#
18-2783
Description:
Replaces 986629, for King Cobra
Lower unit 1990
POWER TRIM HOSE
Part#
18-2483
Description:
pump to manifold up
POWER TRIM HOSE
Part#
18-2442
Description:
manifold to cylinder, port down
OMC STRINGER UPPER, LOWER & INTERMEDIATE SEAL KITS
UPPER UNIT SEAL KIT
Part#
18-2666
Description:
Replaces 981799, for 100-245 Stringer unit’s 1968-1972
LOWER UNIT SEAL KIT
Part#
18-2663
Description:
Replaces 981797, for 100-245 Stringer unit’s 1968-1977
LOWER UNIT SEAL KIT
Part#
18-2665
Description:
Replaces 982946, for V6 & V8 800 Stringer unit’s
1978-1986
UPPER UNIT SEAL KIT
Part#
18-2667
Description:
Replaces 982949, for ALL Stringer unit’s 1973-1986
LOWER UNIT SEAL KIT
Part#
18-2664
Description:
Replaces 982947, for 4 cyl. 400 Stringer unit 1978-1986
INTERMEDIATE HOUSING SEAL KIT
Part#
18-2670
Description:
Replaces 982948, All Stringer units 1978-1986
333
VOLVO PENTA TRANSOM SEAL KIT & EXHAUST BELLOWS
TRANSOM SEAL KIT
For SX Drives
DRIVE BELLOWS KIT
Complete Kit
18-2772-1
Part#
O.E.M.#
18-2100
3853807
Gimbal bearing
18-2765
3854127
Bellows
3850426-2
Bellows
18-1074
18-2996
18-7315
Description:
3852560, 911823 Seal
853012-3
EXHAUST BELLOWS KIT
with flapper valve
Part#
18-2757
Description:
Replaces 875828 & 876633,
for AQ175, 280, 280DP, T,
PT, AQD40, AQAD40, V8
Hose clamp
EXHAUST BELLOWS KIT
Part#
18-2758
Description:
Replaces 875848, for
AQ200, 250, 280DP, T, PT,
AQD40, AQAD40, V8
HOSE CONNECTORS
Part#
18-2777
Description:
Hose connecter, 2 bolt hole,
with NO trim
334
Part#
18-2744
Description:
Replaces 875826 & 876294, (with ridge), for AQ200, 250,
270, 270T, 275, 280, 280T, PT, 290, DP unit 280 & 290
EXHAUST BELLOWS KIT
Part#
18-1074
Description:
Replaces 3850426, for SX
drives including 302, 432,
434, 502, 572, 584, 744
1994-1998, uses 18-7314
clamp
U-JOINT BELLOWS KIT
Part#
18-2765
Description:
Replaces 3854127, for
DP-S, SX
“S” HOSE KITS
Part#
18-2775
Description:
Part#
Part#
Replaces 875822-9, AQ
18-2778
18-2774
drive units 200, 250, 270,
Description:
Description:
Hose connecter, 6 bolt hole, Replaces 875847-6, AQ290, 270T, 275, 280, 280T,
280PT, DP unit 280
with trim
& AQ290DP
VOLVO PENTA U-JONTS, SEALS, WASHERS, BUSHINGS, & COVERS
HEAVY DUTY U-JOINT
SPRING SET
Part#
18-6523
Part#
Description:
18-2104
For reverse tilt locks, fits AQ250, 270,
Description:
275, 275A, 280, 280DP, 280L, 285A, 290,
Replaces 897707 & 853255, for
290A, 290DP, SP-A, SP-A/MT, SP-A1,
AQ200, 250, 270, 280, 290 (rockwell) SP-A2, DP-A, DPA1, DP-A2, DP-B, DP-B1
LOWER GEARCASE SEAL
Part#
18-2366
Description:
Replaces 876279, fits 290, 290A,
290DP, SP-A, SP-A1 & SP-A2
FISH LINE
PROTECTOR SPACER
Part#
O.E.M.#
Application:
18-4208
839423
AQ280, 290
18-4209
839534
AQ250, 270, 275
18-4234
832965
AQ110S, 200
PLASTIC BUSIHING
Part#
18-4205
Description:
Replaces 832820, fits A270T & 280T
PROP CONE
Part#
18-4210
Description:
Replaces 850785 & 854045, fits
AQ200, 250, 270, 270T, 275, 280,
280T, 280PT, 290
SPACER
PLASTIC BUSHING
Part#
18-4204
Description:
AQ200, 25, 270, 275, 280, 280DP,
290DP NOT FOR 270T, 280T, & 290
SETTING PIVOT PIN
Part#
18-2153
Description:
Replaces 814301, fits AQ200, 250,
270, 275, 280
PROP CONE SCREW
Part#
18-4212
Description:
Replaces 850889, 5/16” --- 18
LOCKING WASHER
PLASTIC WASHER
Part#
18-4211
Description:
Replaces 850888
STERNDRIVE COVER
Part#
18-4206
Description:
270, 275, 280, 290
Part#
18-4213
Description:
AQ275, 280, 290
LOCK CATCH SCREW
for stern drive cover 18-4206
Part#
18-4238
Description:
270, 275, 280, 290
Part#
18-4214
Description:
Replaces 897367, fits AQ units 200,
250, 270, 270T TID UTF, 275, 280,
280T, 280PT TID UTF
LOCK CATCH
for stern drive cover 18-4206
Part#
18-4239
Description:
270, 275, 280, 290
335
VOLVO PENTA TRANSOM SEAL KIT &EXHAUST BELLOWS
UPPER SEAL KIT
COMPLETE GEARCASE
SEAL KIT
Part#
18-8357
Description:
Replaces 875741, for 280DP &
290DP
LOWER UNIT SEAL KIT
Part#
18-8359
Description:
Replaces 876268, for AQ200 &
AQ290
POWER TRIM HOSE
Part#
18-2625
Description:
Replaces 875192, for AQ200, 250, 270, 275,
280, 290
Part#
18-2432
Description:
Replaces 873228, for DP, DPX
TRIM FIN
POWER TRIM HOSE
Part#
18-2433
Description:
Replaces 873229m for DP, DPX
ENGINE COUPLERS
1
336
LOWER GEARCASE
SEAL KIT
Part#
18-8358
Description:
Replaces 876267, for 280DP &
290DP
STERNDRIVE GASKET KIT
Part#
18-2194
Description:
Replaces 851452, 854040
Part#
18-2583
Description:
Replaces 3888821, for SX-A drives,
2007 & up
Part#
18-8361
Description:
Replaces 576266-8, for AQ200 &
AQ290
LOWER UNIT SEAL KIT
Part#
18-2584
Description:
Replaces 3888822, fits DPS-A drives,
2007 & up
LOWER UNIT SEAL KIT
2
3
Part#
O.E.M.#
Application:
18-21751
3853962-3
fits 2.5L 1986, 3.0L 1986-90, 4.3, 5.0, 5.7L
1986 KW & KWB suffix only, 7.4L 1990-98,
8.2L 1992-93, 1998
18-21752-1
3858437-1
fits 4.3L 1986-98, 5.0L 1986-88, 1998, 5.7L
1986-92, 1994, 1996-98
18-21751
985727, 3853862-5
fits 5.0 & 5.8L 1998 - 1996
MARINE MOTOR & DRIVE FLUSHERS
MOTOR & DRIVE FLUSHERS & WINTERIZING SYSTEMS
“DIY” DO IT YOURSELF WINTERIZING SYSTEM
Part#
CAC65501
Description:
Do-It-Yourself winterizer allows you to quickly and efficiently service
Outboard and Inboard/Outboard marine engines. With this kit, just
five gallons of antifreeze, and your engine flusher, you can flush
and prepare your boat engine for winter storage. It’s so simple to
use, your engine can even be winterized with your boat right on the
trailer. Complete and easy step-by step instructions are included.
You will save time and money
337

300 STERN DRIVE COMPONENTS

Transcription

Similar documents

mercruiser - East Marine

I/O MERCRUISER

zinc anodes for mercury / mercruiser outdrives