LTD SHEAR BOLTS

Transcription

LTD SHEAR BOLTS

LTD
SHEAR BOLTS
KNIFE PARTS AND ACCESSORIES
1-800-229-0009 • Local: 952-556-5666 • e-mail:[email protected]
Contents
KNIFE BOLTS
1-5
SHEAR BOLTS AND PINS
6-10
POLAR CUTTER PARTS
11-18
POLAR KNIFE BOLTS
19
KNIFE CHANGE HANDLES 20-21
KNIFE CHANGING KNOBS 22
KNIFE BOLT T WRENCH
23-24
CLUTCH HANDLES
25-26
BOOK CLAMPS
27
MISC PARTS
28-29
LTD
We GUARANTEE our PRODUCTS
We guarantee the quality of our products. If you are not satisfied, return the
products for replacement or refund.
To Order
WEB
www.updateltd.com
PHONE
FAX
MAIL
1-800-229-0009
1-952-556-8777
UPDATE
134 Peavey Circle,
Chaska, MN 55318
E-MAIL
[email protected]
n No Minimum Order!
n Orders Shipped Same Day on mosT products
We will use any recommended carriers,
FOB shipping point.
n We accept
n All orders are made subject to the Terms and Conditions
on the invoice provided to the purchaser after the order
is received. For a copy of these Terms and conditions,
please contact Update Ltd.
PRICES SUBJECT TO CHANGE WITHOUT NOTICE
ANY UNAUTHORIZED USE OF PHOTOS, ART AND/OR COPY IN THIS CATALOG IS PROHIBITED.
Copyright © 2010
Updateltd
134 Peavey Circle, Chaska, MN 55318
2380411-3
High Quality Long Lasting Shear Bolts
Top requested shear bolts, handles,
wrenches, stands, switches, shims etc
H67 (207315) Steel knife changing tool is
1-118” in dia. by 7-112” long & zinc plated.
Threaded 12mm (.472”) by 1.75mm pitch.
(14.5 threads/inch).
FOR POLAR 107, 112, 115, 137
$35.00 (see page 51)
S105 Alloy steel shear pin, hex head w/hex nut.
12 MM across flats. Shank is 1.77” long below
head & is threaded 8 MM (.315”). Pitch is .75mm.
(221987, 219562) For POLAR 71 -72 EL CE,
72CS, and Power Max 28 $20.25 each
B43 Hex head bolt and washer with black oxide
finish. Bolt is 112”-12 &11/16” across the flats,
it is 3/4” long below the washer. Washer is 1/8”
thick and 1-3/16” diameter.
FOR SEYBOLDS & OSWEGO (Harris-Seybold)
$10.85 each
with insulated center steel pin, with brass screw
for attaching short out wire lead. (CKC2160) For
Harris Seybold $280.00 each
K14 (010113, 206579) This blade support
handle has a solid plastic body. The steel shank
is 10mm (.390”) dia. POLAR 90 EL, 90 CE (late
models), 92CE, 112ST, 115CE, 115 EL (late
models) & 155CE
$35.00 each
S91 (206016) Steel shear pin, with collar hex
nut. (nut 205525) Shank is 9 MM (.354”) 54 MM
(2-118” long below head. Thread is .75 MM pitch
(34 threads inch). FOR POLAR EL or CE 82, 86,
90, 90ST, 92, 92CE & 92EMC (not 92 EMC II)
$21.00 each
S176 Shear pin, (250600745) 14mm (.550")
diameter shank, 40mm long (1-9116”) below the
head. The head is 32mm in diameter (1-114").
Supplied with “flange” or “collar” nut. FOR
PRISM 115 & 137
$38.00 each
S104 Alloy steel shear pin is complete with
B44 Socket head bolt, Grade 10.9, 112-13, .700"
below the washer. Steel washer is 3/32" thick,
7/8" dia. It rotates freely in a groove and stays in
place but is removable. FOR MOST LAWSONS
$8.30 each
S108 Steel shear pin, 2” diameter, complete
washer faced nut & roll pin. Head is 3/8” thick
x .860” dia. Shank is 1-27/32” below head.
Threaded 12 MM (.472”).
FOR POLAR 76 EM, 78, 78 X, and 78ED
(027920), 017605) $28.00 each
S102 Alloy steel shear pin is complete with
S103 Alloy steel shear pin, same dimensions as
S102 except for the groove depth. Includes nut.
(231658) FOR POLAR 115 EMC II & 115 MON
$42.00 each
S92 (221719) Steel shear pin, complete with hex
nut. Shank is 12 MM (.47”) dia. 65 MM (2-9/16”)
long below head. Thread is 1 MM pitch. Hex head
is 17 MM (.699”) across flats. For POLAR 107EL,
107ST, 112 EL, 115 EL, 115 CE, & 115 EMC (some
107 use our 8114) $24.30 each
S107 Alloy steel shear pin has a round head,
cross drilled for a pin. Head is 24 MM (.945”)
dia. Shank is 48 MM (1.890”) long below head.
It is threaded 14 MM (.551”) . Washer faced
hex nut is 19 MM (.748”) across flats. (017771,
260469, 053063) FOR POLAR 92 EMC II, 92 ED
$28.90 each
washer faced hex nut. The head is 1.180” dia
x .39” thick. A flat on the head is provided as
shown. The shank is 2.330” long below the
head and has a 16 MM (.630”) thread.
(423024, 231671, 260506) FOR POLAR 137
EMC II, MON, X, XT, & ED $42.00 each
BS10 BLADE STAND (014569) A sturdy
aluminum casting with a plastic base.
Generally used in pairs. (also see H67)
$165.00 each See Next Page
G327 Polar Track Change Gear. This gear is
used on Polar 115 CE and Polar 155 CE cutters
built during 1970s. This gear is used on cutters
with the magnetic tape program storage system.
This 15 tooth gear, is accurately machined from
aluminum and is a direct replacement. It will not
crack with age like the original ones. Price each
$175.00
LTD
Knife Bolts 1
B41 - Seybold Knife Bolt
Bolts for Seybold CF and most older Seybolds. This square headed knife bolt is fitted with an integral washer.
The washer rotates on the bolt but is not removable. This bolt has 1/2”-12 threads and measures 25/32”
long below the washer. The square head measures 5/8” across the flats. The steel washer is 1/8” thick and
measures 1-1/8” in diameter. A screwdriver slot is provided in the threaded end to aid in removal if the head
gets rounded over from a worn wrench or socket. (This is the same bolt as our B42 bolt, EXCEPT that it has
a different thread pitch. The B41 has 1/2-12 threads, the B42 has 1/2-13 threads.) Made in USA. See our
part number W80 for a knife bolt wrench that fits these bolts.
$10.08
B42 - Seybold Knife Bolt
Bolts for very early Seybold paper cutters. It is the same as our part number B41 EXCEPT it has a 1/2-13
thread. (Our B41 bolt has a 1/2-12 thread pitch.) This square head knife bolt is fitted with an integral washer.
The washer rotates on the bolt but is not removable. This bolt measures 25/32” long below the washer. The
square head measures 5/8” across the flats. The steel washer is 1/8” thick and measures 1-1/8” in diameter.
A screwdriver slot is provided in the threaded end. Made in USA.
$10.08
B43 - Seybold & Oswego Knife Bolt
Hex Head knife bolts with integral washer. This bolt has a 1/2”-12 thread and measures 3/4” long below
the washer. The hex head is 11/16” across the flats. The washer is 1/8” thick with a 1-3/16” diameter. It is
made from one piece of steel, including the washer, and it includes a screwdriver slot in the tip. It fits many
Seybold and Oswego paper cutters, including the Seybold Citation. This blade bolt has a black oxide finish
for corrosion resistance. Made in USA.
$10.85
B44 - Lawson Knife Bolt
Knife bolts for Lawson paper cutters. This grade 10.9 steel socket head cap screw fits most Lawson
paper cutters. It is .70" long below the 3/32" thick steel washer. It has a 1/2"-13 thread. The 7/8" diameter
threaded washer rotates freely in a groove but it will not fall off the bolt. Made in USA.
$8.30
B45 - Challenge Knife Bolt
Knife bolts for Challenge 20, 265, 265H, 305, Titan 20, and Titan 200 Paper Cutters. Socket head cap screw,
1" long below the head, with a 3/8-16 thread. Supplied complete with a heavy flat washer. The washer is 1"
in diameter and 1/8" thick. Made in USA.
$4.57
B46 - Polar Knife Bolt - B46
Knife Bolts for Polar 107, Polar 112, Polar 115, Polar 137, Polar 145, Polar 150 & Polar 155 paper cutters.
Socket head cap screw, M12 x 22mm long (.87”) below the head. This bolt has a screwdriver slot cut in the
end as shown for ease of removal if the allen key socket gets stripped. Black oxide finish for corrosion
resistance. Also see our knife bolt part number B704 which fits newer models of Polar paper cutters.
$4.20
LTD
Knife Bolts 2
B47 - Polar Knife Bolt
Knife Bolts for Polar 80, 82, 90 & 92 paper cutters (200962). These Grade 12.9 socket head cap screws
have an M10 thread. They are 16mm long (.63”) below the head and have a black oxide finish for corrosion
resistance.
$3.30
B48 - National, Challenge & Early Seybold Knife Bolt
Knife Bolts for Challenge 420, National, and early Seybold Paper Cutters. This 1/2-12 thread steel hex head
cap screw fits Challenge 420, most National, and early Seybold Paper Cutters. The 1/2”-12 thread is 1-3/32”
long below the washer. The hex head is 3/8” high and measures 3/4” across the hex flats. The washer is
captive and is not removable. See our part number W81 for a knife bolt wrench for these bolts.
$11.87
B53 - Schneider and Perfecta Knife Bolt
Knife Bolts for Perfecta & Schneider Paper Cutters. Hex head bolt. M12 x 22mm long below the washer,
1.5mm thread pitch. Steel washer is 30mm (1-3/16") in diameter and is included with each bolt.
$10.15
B54 - Pivano Knife Bolt
Knife Bolts for Pivano Paper Cutters. This socket head cap screw has an M12 thread, a 1.75mm thread pitch,
and it is 30mm (1.18") long below the head. Steel with a black oxide finish.
$3.70
B56 - Chandler & Challenge Knife Bolt
Knife bolts for Price Paper Cutters and some Challenge Paper Cutters. (S645 V thread) These bolts also fit
older (pre 1950) Pavyer table top paper cutters. This steel hex head bolt has a 1/2-12 thread. It measures
13/16" long below the washer. The hex head measures 3/4" across the flats. The steel washer is captive; it
rotates but does not come off. The steel washer is .11" thick and measures 1-3/8" in diameter. See our part
number W81 for a knife bolt wrench for these bolts.
$11.87
B57 - Imperial and Horizon Knife Bolt
Knife Bolts for Imperial & Horizon Paper Cutters. This steel hex head bolt is 11mm ( .43") long below the
head. It has an M10 thread with a 1.5mm thread pitch. The head measures 17mm (.67") across the flats and
is 5mm (.20") high. Black oxide finish for corrosion resistance.
$8.21
B60 - Wohlenberg Knife Bolt
Knife bolts for Wohlenberg Paper Cutters. These alloy steel socket head blade bolts use a Torx Plus driver
and are used on most Wohlenberg paper cutters. They are .70” long below the washer and have a 1/2-13
thread. The 4140 hardened steel washer is captive on the head; it rotates in place but it will not fall off. While
it is possible to tighten and remove these with a Torx driver, they are designed for a Torx Plus driver. Using
the incorrect driver will eventually strip the bolt head. See our PART NUMBER B3 for the correct driver.
$12.14
LTD
Knife Bolts 3
Knife bolts for Wohlenberg Paper Cutters. They are .97” long below the washer and have a 1/2-13 thread. The
4140 hardened steel washer is captive on the head; it rotates in place but it will not fall off. These alloy steel
socket head blade bolts use a Torx Plus driver and are used on many Wohlenberg paper cutters. While it is
possible to tighten and remove these with a Torx driver, they are designed for a Torx Plus driver. Using the
incorrect driver will eventually strip the bolt head. See our PART NUMBER B3 for the correct driver.
$12.14
B62 - Pivano Knife Bolt
Knife bolts for Pivano Paper Cutters. Socket Head Cap Screw, M12 x 30mm (1.18") long below the head.
1.5mm thread pitch. Black oxide finish for corrosion resistance.
$3.70
Knife bolts for Wohlenberg Paper Cutters. This bolt is 25mm (.98”) long below the washer and has an M12
thread. The washer is captive on the head; it rotates in place but it will not fall off. These alloy steel socket
head blade bolts use a Torx Plus driver and are used on many Wohlenberg paper cutters. While it is possible
to tighten and remove these with a Torx driver, they are designed for a Torx Plus driver. Using the incorrect
driver will eventually strip the bolt head. See our PART NUMBER B3 for the correct driver.
$12.58
Knife bolts for Wohlenberg Paper Cutters. This bolt is 19mm (.75”) long below the washer and has an M12
thread. The washer is captive on the head; it rotates in place but it will not fall off. These alloy steel socket
head blade bolts use a Torx Plus driver and are used on many Wohlenberg paper cutters. While it is possible
to tighten and remove these with a Torx driver, they are designed for a Torx Plus driver. Using the incorrect
driver will eventually strip the bolt head. See our PART NUMBER B3 for the correct driver.
$12.58
B65 - ITOH Knife Bolts
Knife Bolts for ITOH Paper Cutters Socket Head Bolt, 1/2-12 thread, 1-1/8" overall length below the washer.
The captive washer is fixed in place and will not fall off.
$8.60
B66 - Polar 92 Knife Bolt
Knife Bolts for some Polar 92 Paper Cutters. This steel, low head, hex head bolt fits some Polar 92 Paper
Cutters. It has a 10mm thread and measures 20mm (.79”) long below the washer. The heavy steel washer is
1” in diameter and 1/8” thick. The washer also has a beveled outer edge. The washer rotates in place but is
held captive, it will not fall off.
$12.58
B67 - Triumph Knife Bolt
Knife Bolts for Triumph No. 46, 48, 4800, 4810 & 4850 Paper Cutters These special socket head bolts have a
low profile head. They have an M10 thread which is 13mm (.51”) long below the head. The head is 16mm in
diameter and is 6mm thick. Black oxide treatment for corrosion resistance.
$4.20
LTD
Knife Bolts 4
B511 - Pivano Knife Bolts
Knife Bolts for 40" Pivano Paper Cutters. Socket head cap screw, M12 x 25mm long below the head. 1.75mm
thread pitch. Also see our Pivano knife bolt part number B62.
$3.00
Knife Bolts for Polar 76, Polar 76 EM and some Polar 72 (28”) Paper Cutters (014116, 021053) Socket head
cap screw, 10mm thread by 21mm long (.83”) below the washer. It has a 1” diameter washer which is 1/4”
thick and has been counter bored 1/16” deep to fit the head. The washer is held captive by a snap ring. See
our part number B522 for a shorter version of this same bolt. Be sure to check your existing bolt length.
Order these by the bolt length under the washer, not by the Polar model number.
$13.44
Knife Bolts for Polar 55, Polar 66, Polar 71 and some Polar 72 (28”) Paper Cutters (014775, 014776, 021054,
200276) Socket head cap screw, 10mm diameter thread by 17mm long (.67”) below the washer. It has a 1”
diameter washer which is 1/4” thick and has been counter bored 1/16” deep to fit the head. The washer is
held captive by a snap ring. See our part number B521 for a longer version of this same bolt. Order these by
the bolt length under the washer, not by the Polar model number.
$13.44
B700 - Knife Bolt for Clark Aiken Sheeter
These special plow type knife bolts are for a Clark Aiken Sheeter. They have a 3/8-16 thread and their overall
length is 4-3/8” long. The head was slotted and has a steel key or ear which has been silver soldered into
place in the slot.
$14.00
B702 - Triumph MBM Ideal Knife Screws
Knife Screws for MBM Triumph 3600, MBM Triumph 3610, and Triumph Ideal 3915 Paper Cutters.
(3600-030) These custom made screws have a 6mm diameter thread. They are 10mm long below the head.
The slotted head is 10mm in diameter.
$3.70
B703 - Bolt for Sheridan VT Trimmer
Grade 8 steel hex head bolts, 1/2-13 threads by 1-31/32” long below the washer. The washer is an integral
part of the head and does not rotate and will not fall off. The washer is 1-1/16” in diameter. Black oxide finish
for corrosion resistance. Hex head measures 3/4” across the flats. These bolts are used in a Sheridan VT
Trimmer.
$6.21
LTD
Knife Bolts 5
Knife Bolts for Polar X, XT, E and ED Paper Cutters (409569, 419520). These zinc plated, grade 12.9, hex
head cap screws have a 12 mm diameter thread. Included with each bolt is a heavy 4mm thick zinc plated
washer made from heat treated 4140 steel. These blade bolts are 24.5mm long below the washer. The washer
is threaded to keep it in place. These knife bolts fit the following Polar Paper Cutters: 78X, 78XT, 78E, 78ED,
78ES, 92X, 92XT, 92E, 92ED, 115X, 115XT, 115E, 115ED, 137X, 137XT, 137E, 137ED, 155X, 155XT, 155E,
155ED, 176X, 176XT, 176E, 176ED. Also see our part numbers B46, B47, B66, B521, and B522 for knife bolts
which fit older models of Polar Paper Cutters.
$11.50
B705 - Prism Knife Bolt
Knife Bolts for Prism Paper Cutters. This hex head flange bolt fits in Prism 116 and other Prism paper cutters.
It has an M12 thread, it is 24mm (.98”) long below the head, and it has a 25.4mm (1”) diameter washer built
into it. Both the bolt and the washer are machined out of a single piece of 4140 cold rolled steel. The washer
will not rotate. The oversize head measures 19mm (.75”) across the flats. It has a screwdriver slot machined
into the tip of the threaded end to help remove it if the hex head wears down. It also has a black oxide finish
for corrosion protection.
$12.50
LTD
Shear Bolts and Pins 6
S91 - Polar Shear Bolt
Shear pins for Polar 82 EL, 82 CE, 86 EL, 86 CE, 90 EL, 90 CE, 92 EL, 92 EMC & 92 CE Paper Cutters.
(206016) (These shear bolts do NOT fit the Polar 92 EMC II, see our part number S107 for the 92 EMC II
shear pin). The main shank on this shear bolt measures 9mm (.354”) in diameter, except where it is
undercut. It is 54mm (2-1/8”) long below the head. It has an M9 thread and two flats are cut on the sides of
the head. Included with each of these shear bolts is a mating washer faced nut. (collar nut number 205525)
$21.00
Alloy Steel Shear Pins for Polar 107 EL, 107 ST, Polar 112 EL, Polar 115 EL, Polar 115 CE & Polar 115 EMC
Paper Cutters (221719) This shear bolt or shear pin is designed and engineered to replace the original factory
overload shear bolt. The main shank is 12mm (.47”) in diameter, except where it is undercut. It is 65mm
(2-9/16”) long below the head. It has an M12 x 1mm thread with a 17mm hex head. Included with each of
these shear bolts is a mating hex nut. (Also see our PART NUMBER S103 for shear bolts for Polar 115 EMC
II paper cutters.) Note that some of the early Polar 107 cutters did not use this shear bolt but used a smaller
(10mm diameter x 65mm long) shear bolt with a cross drilled hole. See our part number S114 for these
smaller shear bolts.
$24.31
Steel Shear Bolts for Polar 145EL, Polar 150EL, Polar 150CE, Polar 155CE, and Polar 155 EMC (not 155
EMCII) Paper Cutters. (221301, 221302) (serial numbers 61896 and higher) The largest diameter on the
shank on these shear pins is 14mm (.54”), except where it is undercut. It is 80mm (3.15”) long below the
head. It has an M14 thread. A matching hex nut is also supplied with each of these shear bolts. (nut number
205518) Note that some of these were originally supplied with through holes at the break point and some
were originally supplied with a groove at the break point. Both styles are interchangeable.
$30.00
S94 - Lawson Pacemaker Shear Bolt
Steel Shear Pins for Dexter Lawson Pacemaker II, III, IV, & V Paper Cutters. This steel shear pin fits Lawson
Pacemaker 2, 3, 4 & 5 paper cutters. The main shank on this special socket head cap screw is 3/8” in
diameter and is 2-1/2” long below the head. It has a 3/8-16 thread. An elastic stop nut is also supplied with
each of these shear bolts. (2BA2155)
$10.30
Steel Shear Pins for Polar 155 EMC and 155 MON Paper Cutters. (260465) The main shank on this alloy steel
shear bolt is 3-1/32” long below the head and has an M20 (.79”) thread. The head is 1-15/32” in diameter
and 15/32” thick. The head is cross drilled for a roll pin which is supplied already installed in the head.
Also included with each of these shear bolts is a mating M20 washer faced hex nut (collar nut).
$58.57
Steel Shear Pins for Polar 137 EMC II, 137 MON, 137 X, 137 XT, and 137 ED Paper Cutters. (231671,
ZA3.423024, 260506) This alloy steel shear pin or shear bolt fits Polar 137 EMC II, Polar 137 MON, Polar 137
X, Polar 137 XT, and Polar 137 ED paper cutters. The main shank has an M16 (.63”) thread and is 2.33” long
below the head. Included with each of these shear bolts is a mating washer faced hex nut (collar nut 231661).
The head is 1.18” in diameter and .39” thick and has a flat on one side as shown in the photo.
$42.00
LTD
Steel Shear Pins for Polar 115 EMC II & Polar 115 MON Paper Cutters. (231658) This alloy steel shear pin or
shear bolt fits the pull arm on Polar model 115EMC II & 115MON paper cutters. The main shank has an M16
(.63”) thread and is 2.33” long below the head. Included with each of these shear bolts is a mating washer
faced hex nut (collar nut 231661). The head is 1.18” in diameter and .39” thick and has a flat on one side as
shown. Also see our PART NUMBER S92 for the shear pin for Polar 115 EMC (not 115 EMC II) cutters.
$42.00
Steel Shear Pins for Polar 76 and 78 Paper Cutters. (027920, 017605) This alloy steel shear pin or shear bolt
fits most Polar 76, Polar 76 EM, Polar 78, Polar 78 X, and Polar 78 ED paper cutters. The main shank is 1.84”
long below the head. It has an M12 thread. Included with each of these shear bolts is a mating washer faced
hex nut (collar nut 233166) and a steel roll pin. The roll pin is supplied already installed in the head. The head
measures 22mm (.86”) in diameter by 9.5mm (3/8”) thick.
$28.00
Steel Shear Pins for most Polar 71 and Polar 72 paper cutters. (221987, 220329, 219562). This alloy steel
shear pin or shear bolt fits Polar 71 EL, 71 CE, 72 EL, 72 CE, 72 CS, and Power Max 28” paper cutters. The
main shank is 1.77” long below the head. It has an M8 thread. Included with each of these shear bolts is a
mating washer faced hex nut (collar nut 219563). Both the nut and the head measure 12mm (.472”) across
the flats.
$20.25
Steel Shear Pins for Polar 80 EL Paper Cutter (208943) This alloy steel shear pin or shear bolt fits most Polar
80 EL paper cutters. It has a “D” style head, round with two wrench flats machined into it. The main shank is
45mm (1.77") long below the head. It has an M9 thread. Included with each of these shear bolts is a mating
washer faced hex nut (collar nut).
$20.30
Steel Shear Bolts for Polar 92 EMC II and Polar 92 ED Paper Cutters. (260469, 017771, 053063) The main
shank on this shear bolt or shear pin is 48mm (1.89") long below the head. It has an M14 thread. Included
with each of these shear pins is a mating washer faced hex nut (collar nut). The nut measures 19mm (.75")
across the flats. Also included with each shear bolt is a steel roll pin. The roll pin is supplied already installed
through the head.
$28.90
S108 - Harris Seybold Shear Bolt
Shear Pins for Seybold (Harris-Seybold) Paper Cutters. (CKC2160 or XCKC2160)) This 2" diameter by
4-13/16” long steel shear pin fits many Harris Seybold paper cutters. It is supplied complete with the
insulated center short out pin assembly. This trips out the machine by blowing a fuse when the pin breaks
during an overload condition. This is to prevent the pull arm from cycling once the shear pin brakes apart.
$280.00
S109 - Standard Horizon Binder Shear Bolt
Alloy Steel Shear Pins for Standard Horizon Binder. This 6mm diameter alloy steel shear pin or shear bolt fits
the Standard Horizon Binder. It is 42mm long below the head.
$9.75
LTD
S110 - COMO Shear Bolt
Steel Shear Bolt for Como Paper Cutters. This shear pin measures 80mm (3.15”) long below the head and it
has a 10mm thread. The head is 22mm in diameter (.87”) and it has two wrench flats machined into it. The
main section of the shank is 10mm in diameter. These COMO shear bolts are made in USA.
$35.00
S112 - ITOH Robocut and Saber Shear Pin
Steel Shear Pins for Saber 116 Paper Cutters and ITOH Robocut Paper Cutters. The main shank on this grade
12.9 steel socket head cap screw shear bolt is 8mm (.31”) in diameter, except where it is undercut. It is
55mm (2.16”) long below the head. It has an M8 thread. Included with each of these shear bolts is a mating
zinc plated flat washer and a zinc plated elastic stop nut.
$13.00
S113 - Saber Shear Pin
Steel Shear Pins for Saber 137 Paper Cutters. This grade 12.9 steel socket head cap screw shear bolt fits
Saber 137 paper cutters. The main shank is 10mm (.39”) in diameter, except where it is undercut. It is 55mm
(2.16”) long below the head. It has an M10 thread. Included with each of these shear bolts is a mating zinc
plated flat washer and a zinc plated elastic stop nut.
$13.80
Steel Shear Bolt for some of the early Polar 107 Paper Cutters. The main shank on this hex head shear bolt or
shear pin is 10mm in diameter and it is 65mm (2-9/16”) long below the head. It has an M10 thread and has a
cross hole drilled through the shank at the break point. Included with each of these shear pins is a mating hex
nut. The nut, as well as the hex head, measure 17mm (.67”) across the flats. Note that many of the later Polar
107 cutters use a larger shear bolt which measures 12mm in diameter but are also 65mm long. See our part
number S92 for this larger shear bolt.
$14.00
S175 - Prism Shear Bolt
Steel Shear Pins for Prism 78 & Prism 92 Paper Cutters. (250600832) This steel shear pin or shear bolt is an
aftermarket direct replacement for the original bolt supplied by the factory on Prism 78 and Prism 92 paper
cutters. The main shank is 12mm (.47") in diameter and is 40mm (1.57”) long below the head. It has an M12
thread. Included with each of these shear bolts is a mating elastic stop nut and a washer. The head is 28mm
(1.11") in diameter with two flats. The head is eccentric to the shank.
$29.00
S176 - Prism Shear Bolt
Steel Shear Pins for Prism 115 and Prism 137 Paper Cutters. (250600745) This steel shear pin or shear bolt
is an aftermarket direct replacement for the original bolt supplied by the factory on Prism 115 and Prism 137
paper cutters. The main shank is 14mm (.55") in diameter and is 40mm (1.57") long below the head. It has an
M14 thread. Included with each of these shear bolts is a mating flange nut. (250600933) The head is 32mm
(1.26") in diameter with two flats. The head is eccentric to the shank.
$38.00
S201 - Wohlenberg 115 Shear Bolt
Alloy Steel Shear Bolt for Wohlenberg 115 Paper Cutters. (7004991) This alloy steel shear pin or shear bolt
fits Wohlenberg model 115 paper cutters. The main shank is 16mm (.63”) in diameter and is 50mm (1.97”)
long below the head. It has an M16 thread. The main shank is cross drilled for an exact breaking load. Our
bolts have been tensile tested by an independent lab and broke within 3% of the load which is specified by
Wohlenberg. While some other venders are selling bolts with one size cross hole for several machine sizes,
according to the Wohlenberg machine manual, this is not correct. Each size machine requires a different size
cross hole. Each of our bolts is engineered for the correct breaking load for a specific machine size.
Part Number Fits Machine Price Each
S201 Wohlenberg 115 $32.85
S204 Wohlenberg 180 & 185 $32.85
Alloy Steel Shear Bolt for Wohlenberg 137 Paper Cutters. This alloy steel shear pin or shear bolt fits
Wohlenberg model 137 paper cutters. The main shank is 16mm (.63") in diameter and is 50mm (1.97") long
below the head. It has an M16 thread. The main shank is cross drilled for an exact breaking load. Our bolts
have been tensile tested by an independent lab and broke within 3% of the load which is specified by
S204 Wohlenberg 180 & 185 $32.85
Alloy Steel Shear Bolt for Wohlenberg 155 Paper Cutters. (7004395) This alloy steel shear pin or shear bolt
fits Wohlenberg model 155 paper cutters. The main shank is 16mm (.63") in diameter and is 50mm (1.97")
long below the head. It has an M16 thread. The main shank is cross drilled for an exact breaking load. Our
bolts have been tensile tested by an independent lab and broke within 3% of the load which is specified by
S204 Wohlenberg 180 & 185 $32.85
LTD
S204 - Wohlenberg 180 & 185 Shear Bolt
Alloy Steel Shear Bolt for Wohlenberg 180 & 185 Paper Cutters. This alloy steel shear pin or shear bolt fits
Wohlenberg model 180 paper cutters and Wohlenberg 185 paper cutters. The main shank is 16mm (.63”)
in diameter and is 50mm (1.97”) long below the head. It has an M16 thread. The main shank is cross drilled
for an exact breaking load. Our bolts have been tensile tested by an independent lab and broke within 3% of
the load which is specified by Wohlenberg. While some other venders are selling bolts with one size cross
hole for several machine sizes, according to the Wohlenberg machine manual, this is not correct. Each size
machine requires a different size cross hole. Each of our bolts is engineered for the correct breaking load for
a specific machine size.
S204 Wohlenberg 180 & 185 $32.85
S205 - Wohlenberg 92 G Shear Bolt
Alloy Steel Shear Bolt or shear pin for Wohlenberg 92G, Wohlenberg 86, and Lawson Regent paper cutters.
(8573, 7003224) The main thread is 12mm in diameter and measures 45mm long below the head. These
originally had a hole cross drilled through the side of the shank. However there was a recall on the original
style bolt as they were too strong and would not break during an overload condition. This is the replacement
style that was supplied after the recall. It has a black oxide finish for corrosion protection.
$14.00
S206 - Wohlenberg 76 SPM Shear Bolt
Alloy Steel Shear Bolt for Wohlenberg 76 SPM Paper Cutters. (9158, 25053) This alloy steel shear pin or
shear bolt fits certain Wohlenberg 76 Paper Cutters. The main thread is 10mm and measures 45mm long
below the head. There is a drilled hole down the center of the head into the shank to create the break point.
This style replaces the old style with the cross drilled hole through the side of the shank. It has a black oxide
finish for corrosion protection.
$11.00
S207 - Wohlenberg 92 F Shear Bolt
Alloy Steel Shear Bolt for Wohlenberg 92 F Guillotine Paper Cutters. This alloy steel shear pin or shear bolt
fits certain Wohlenberg 92F Paper Cutters. The main thread is 10mm in diameter and measures 40mm
(1.57") long below the head. There is a necked down notched area machined into the threaded part of the
bolt. This is sometimes refered to as the “old style” shear bolt for these machines. It has a black oxide finish
for corrosion protection.
$13.50
LTD
Polar Cutter Parts 11
AJ501 - Polar Air Jet Nozzle
Air Jet Nozzles for Polar paper cutters. These are 30mm (1.18”) long, including the height of the protruding
ball. These air jets or air nozzles are used in early Polar guillotine paper cutter air tables and air feed tables,
Polar jogger tables, as well as in other industrial applications for material flotation. They allow for easy
movement of stacks of paper or card stock by allowing the stock to float on a thin layer of air. Once the stock
clears the button the air jet closes off to prevent wasting air. They are a press fit in the 15 millimeter diameter
reamed holes in the table.
$14.50
AJ502 - Polar Air Jet Nozzle
Air Jet Nozzles for Polar paper cutters. (010800, 010807) These air jets or air nozzles are used in Polar
guillotine paper cutter air tables and air feed tables as well as in other industrial applications for material
flotation. They allow for easy movement of stacks of paper or card stock by allowing the stock to float on a
thin layer of air. Once the stock clears the button the air jet closes off to prevent wasting air. They are a press
fit in the 15 millimeter diameter reamed holes in the table. They are 40mm (1.57”) long, including the height
of the protruding ball. This style was generally used in Polar cutters built after the mid 1960’s.
$15.50
BB101 - Sliding Bronze Guide Block
Sliding bronze guide block for the knife carrier in Polar 115 and Polar 137 paper cutters. This fits all models
from CE, EM, EMC EMC II, X, XT E through ED. This guide block measures 1.531” x 2.401” x 4 3/4” long
with a 40mm diameter reamed hole. This block is normally installed on one side of the machine with our
mating part number BB102 installed on the other side of the machine. (224340, 209100)
$225.00
Sliding bronze guide block for the knife carrier in Polar 115 and Polar 137 paper cutters. This fits all models
from CE, EM, EMC EMC II, X, XT E through ED. This block measures 1.531” x 2.401” x 4” long with a 40mm
diameter reamed hole. This guide block is normally installed on one side of the machine with our mating
block part number BB101 installed on the other side of the machine. (224339, 208999)
$218.00
Sliding bronze guide block for the knife carrier in Polar 92 EMC paper cutters. This may also fit other sizes of
Polar guillotine paper cutters. This guide block measures 1.535" x 2.018” x 3-3/8" long with a 36mm
diameter reamed hole. This block is normally installed on one side of the machine with our mating part
number BB104 installed on the opposite side of the machine. (206006)
$210.00
Sliding bronze guide block for the knife carrier in Polar 92 EMC paper cutters. This may also fit other sizes of
Polar guillotine paper cutters. This block measures 1.535" x 2.018” x 4" long with a 36mm diameter reamed
hole. This sliding guide block is normally installed on one side of the machine with our mating part number
BB103 installed on the opposite side of the machine. (206005)
$216.00
LTD
BB115CE - Blade Back Up Bars
Blade Back Up Bars for Polar 115 CE and Polar 115 EMC Paper Cutters (014179) These steel backing bars or
knife spacers are mounted in the blade carrier so that the second, lower set of mounting holes can be used
on the blade when the blade has been sharpened down to half of its original size. The socket head cap screws
are secured in the blade spacers. The 12mm screws will rotate but will not fall out. The bars are 15-3/4” long
and are ground on their top and bottom surfaces for an exact fit. They are sold in pairs. The price shown is
for one pair. (See our part number BB115EL for backup bars that fit on Polar 115 EL guillotine paper
cutters.)
$100.00
BS10 - Polar Blade Stand
Blade stand for knife changing on larger Polar Paper Cutters. (014569) This cast aluminum blade stand has
a smooth nylon base. It is used for changing the blade on larger Polar Paper Cutters, as well as some other
paper cutters. It is normally used in pairs and in conjunction with our H67 knife changing tool. Price is for
one stand.
$165.00
BS-2245 - Blade Shim Support Kit (2 Hole)
These 2-hole blade shims or blade supports are used in some Polar EMC paper cutters and some Polar 76EM
paper cutters. They are sold as a kit which includes the following parts:
Item
Plastic shim or support (230056)
Double sided adhesive shim
Plastic flat head screw (201681)
Quantity per kit
2
2
4
Their overall length is approximately 127mm long (5” long) by approximately 40mm wide (1-9/16” wide).
The tapered screw mounting holes are spaced approximately 100mm (3-15/16”) apart.
Note that some Polar EMC machines take a shorter 2-hole shim. Be sure to measure the length of your
existing shims before ordering.
$54.00
BS-2250 - Blade Shim Support Kit (3 Hole)
These blade shims or blade supports are used in Polar EMC paper cutters. They are sold as a kit which
includes the following parts:
Item
Plastic shim or support (224904)
Double sided adhesive shim (224910)
Plastic flat head screw (201681)
Quantity per kit
2
2
6
Their overall length is approximately 177mm long (7" long) by approximately 40mm wide (1-9/16" wide). The
tapered screw mounting holes are spaced approximately 76mm (3”) apart.
$58.00
CAL10 - Pressure Control Petal
Polar Pressure Control Handle or Pressure Set Handle (010028, 010784, 232637). This pressure set handle
or “foot pedal” fits all Polar models which use this type of pressure adjusting handle. It is made of cast
aluminum, has a 20mm diameter through hole, and has a reference scale riveted to the face. It is a direct
replacement for the original Polar plastic handle. It will not crack with age like the original handles.
$140.00
LTD
CB10 - Carbon Brush
Carbon Brush for Backgauge Reversing Slip Ring for Polar Paper Cutters. This carbon brush is used on the
backgauge reversing slip ring on most Polar cutters made before 1968. The carbon end measures 4mm
square x 15mm long. (.16” square x .59” long)
$8.21
CB11 - Carbon Brush
Carbon Brush for Magnetic Clutch for Polar EL Paper Cutters. This carbon brush is for the Magnetic Clutch on
Polar 71 - 76 EL cutters built before 1968. It measures 8mm x 20mm x 25mm. (.315” x .787” x .984”)
CB12 - Carbon Brush
Carbon Brush for the Magnetic Clutch on some Polar 71, 72, 76, and 78 Paper Cutters (210610)This carbon
brush fits the magnetic clutch on Polar 71ST, Polar 72CE, Polar 76EM, Polar 78E, Polar 78ES, Polar 78ED,
Polar 78X, Polar 78XT, and Polar 107ST paper cutters. It measures 6.5mm x 10mm x 15mm. (.256” x .394”
x .590”)
$5.00
CS-500 - Polar Cut Switch
This cut button or cut switch is used on the front of the table on many Polar paper cutters. (027293) This
is an aftermarket switch which is a direct replacement for most 4 pin and 5 pin cut switches. The connector
pins are gold plated for long life. The switch and connector cable are pre-wired for a direct replacement. The
internal switch components are a Moeller M22 modular switch assembly which is Made in Germany. The face
measures 150mm (5-7/8”) wide by 94mm (3-11/16”) tall. The 5mm diameter mounting holes in the face are
103mm (4-1/16") apart. Also interchanges with 014755, 014222, and 017325.
$280.00
CSTL - Polar Cut Stick Retainer (Left Side)
Polar Cut Stick Retainers (206224, 206225). These plastic blocks are 5/8" square x 1 3/8" long. They mount
on the side of the table on Polar Paper Cutters where the cut stick ends.
$8.00
CSTR - Polar Cut Stick Retainer (Right Side)
Polar Cut Stick Retainers (206224, 206225). These plastic blocks are 5/8” square x 1 3/8” long. They mount
on the side of the table on Polar Paper Cutters where the cut stick ends.
$8.00
FP10 - Polar Foot Pedal
Polar Clamp Foot Pedal. (206045, 223633) This steel foot pedal controls the clamp on Polar paper cutters. It
fits most models of Polar EL and CE paper cutters. It measures 20” long. Once the pedal reaches the end of its
stroke, the adjustable stop hits against the floor. This prevents overstressing the pedal or the shaft inside the
cutter. Without this adjustable stop, repeated overstressing will often lead to the original pedal breaking off.
$140.00
FPA25 - Anvil for False Clamp Pin Installation
This steel anvil tool is 2” in diameter by 4” long. It weights 3-1/2 pounds. It is used to position and hold the
false clamp pin in place while the bottom end of the pin is peened over with a hammer. One end is accurately
machined to fit over the P10 pin while the opposite end fits over the P11 pin. The ends of the anvil tool are
steel stamped for proper identification.
$46.00
LTD
FW1 - Polar Flywheel Cover
Flywheel Cover for Polar 115 Paper Cutters (206663). This clear plastic flywheel cover is a direct replacement for the original cover which was used on most Polar 115 paper cutters. It is approximately 10-3/4” in
diameter with three drilled mounting holes.
$71.50
Flywheel Cover for Polar 82, Polar 90 & Polar 92 Paper Cutters (208556). This clear plastic flywheel cover
is a direct replacement for the original cover. It is approximately 8-1/4” in diameter with 2 drilled mounting
holes. When using this cover in a Polar 82, two new mounting holes will have to be drilled in this cover.
$60.00
Rectangular Flywheel Cover for Polar 71 & Polar 72 Paper Cutters. (207751) This rectangular clear plastic
flywheel cover is a direct replacement for the original cover. Its outside dimensions are 7-1/4” x 11” with two
drilled mounting holes.
$71.50
G101 - Blade Setting Gauge for Polar 82 & 92
Blade Setting Gauge for Polar 82 and 92 Paper Cutters (013746) This blade setting gauge is used to set the
height of the blade during blade changes on a Polar 82 or a Polar 92 Paper Cutter. See G102 for gauge used
on larger Polar cutters.
$103.00
G102 - Blade Setting Gauge for Polar 115 to 155
Blade Setting Gauge. (013747) This blade setting gauge is used to set the height of the blade during blade
changes on a Polar 115 EL, Polar 115 CE (early models), Polar 137, and Polar 155 Paper Cutters. See our
part number G101 for the gauge used on smaller Polar cutters.
$107.00
G325 - Hand Fine Pinion Gear
Polar Hand Fine Pinion Gear (206286). This 15 tooth helical gear is used in the hand fine adjustment
mechanism on most Polar EL and Polar CE paper cutters. It measures 2-3/4” long by 1-1/4” diameter at the
large end and it is machined from delrin. Included with each gear is an INA needle bearing which is preinstalled inside the gear. This gear mates with our helical spur gear part number G326.
$142.00
G326 - Hand Fine Spur Gear
Hand Fine Spur Gear (206273). This 55 tooth helical spur gear is used in the hand fine adjustment
mechanism on most Polar EL and Polar CE paper cutters. It measures 3-3/16" in diameter over the teeth. Its
overall length is approximately 1-3/32" wide and about 19/32" wide across the face of the teeth. It fits on the
25mm diameter shaft and is machined from delrin. This gear mates with our pinion gear part number G325.
$112.00
LTD
G327 - Polar Track Change Gear
Track Change Gear for Polar paper cutters. This gear was predominantly used on Polar 115 CE and Polar 155
CE paper cutters which were built during the 1970s. This gear is used in the mechanism which changes the
“track” on the wide magnetic tape on cutters with the magnetic tape program storage system. If your original
metal and plastic gear has cracked and failed then this replacement gear will work as a direct replacement for
the original gear. This one piece, 15 tooth gear, is accurately machined from aluminum. It will not crack with
age like the original ones eventually do.
$175.00
H65 - Polar Knife Changing Handle
Knife Changing Handle for most Polar 71, 72, 76, 82 & 92 Paper Cutters (206579). This solid steel handle
is 5” long. The 1/2” diameter shank is knurled over most of its length for a slip resistant grip. It has a black
oxide finish for corrosion protection. The thread is an M10 x 1.5mm which is 12mm long (.47”).
$16.00
Knife Changing Handle for most Polar 107, 112, 115, 137, and 155 Paper Cutters. This solid steel handle is
5” long. The 1/2” diameter shank is knurled over most of its length for a slip resistant grip. It has a zinc plated
finish for corrosion protection. The thread is an M12 x 1.75mm which is 12mm long (.47”).
$16.00
Knife Changing Handle for Polar 107, 112, 115, 137 and 155 Paper Cutters. (207315) This solid heavy duty
steel handle is 7-1/2” long. The 1” diameter shank is knurled over most of its length for a better grip. The
thread is an M12 x 1.75mm which is 14.5mm long (.57”). This heavy blade change handle (weights almost
1-1/4 pounds) is machined from one piece of solid steel bar stock and is zinc plated for corrosion protection.
It is often used in conjunction with our blade stand, part number BS10.
$35.00
Knife Changing Handle for Polar 82 EL, Polar 82 ST, and Polar 86 EL Paper Cutters. (010660) These handles
or blade supports have a 7/8” long, M10 steel stud. They have a 1.5mm thread pitch. It is used for knife
changing on most Polar EL models of paper cutters. The hand grip is made of phenolic plastic and the disk is
a semi-hard plastic.
$22.85
K14 - Polar Knife Changing Handle
Knife Changing Handle or support for Polar 90EL, 90CE, 92CE, 112ST, 115CE, 115EL (late models) & 155CE
Paper Cutters. (010113, 206579) This “insert and twist” type blade support handle has a solid nylon plastic
body with a plastic handle. The steel shaft is 10mm (.39”) in diameter with a fixed solid steel 4mm diameter
pin for sliding down the slot. It is used for blade changing on most Polar 90 EL, 90 CE (later models), 92 CE,
112 ST, 115 CE, 115 EL later models & 155 CE paper cutters. These all require this twist type blade support
for use during knife changes.
$35.00
LTD
K15 - Polar Blade Change Support Handle
Knife Changing Support Handle for use on Polar 72 CE, 76 EM and Power Max 28 Paper Cutters.(010755)
The 10mm diameter pin on this 10” long steel blade support handle is inserted in a hole in the guide on the
right side of the table. The nose of the blade support handle is then rotated up against the front face of the
blade. This helps keep the blade in place as the knife bolts are removed or installed. Changing the blade
without this blade support tool creates an unsafe condition.
$63.00
LA - Locking Lever Arm
This locking lever arm (205912) fits on the locking valve on Polar CE model paper cutters. It is machined
from cast aluminum.
$40.00
OB - Oiler Manifold Block
Oiler Manifold Block for most Polar 82, Polar 86, Polar 90 & Polar 92 Paper Cutters. This cast aluminum oiler
manifold block is used on some CE and some EL models. (206276 & 224525)
$50.00
P10 - Polar False Clamp Pin
Steel false clamp pin for Polar paper cutters. (206035) 47mm (1.85”) long. Notched as shown. The end of
these pins gets peened over to install them in your Polar false clamp. These false clamp pins are made in the
USA.
See our part number P11 false clamp pin for use on EMC 2 (EMC II) Polar paper cutters.
$11.00
P11 - Polar False Clamp Pin
Steel false clamp pin for Polar paper cutters, 41.5mm (1.63”) long. (232338) Notched as shown with flats cut
on both sides of the large diameter area of the shank. This fits on newer Polar Paper Cutters (Polar EMC 2).
The end of these pins gets peened over to install them in your Polar false clamp. These quality false clamp
pins are made in the USA.
Also see our part number P10 false clamp pin.
$11.00
P325 - Latch Pin Assembly for False Clamp
This latch pin assembly locks into the false clamp pin on Polar 72 CE paper cutters. The overall length of the
latch pin (including the threaded shank) is approximately 43mm long (1 3/4” long). It is 8mm in diameter
at the latching end. This assembly may also fit some of the other smaller sizes of Polar cutters, such as the
PowerMax 28. As shown in the photo, this assembly includes the latch pin (216198), the spring (207788),
the knurled knob with lock pin (205527, 200787), and a self-locking hex nut.
For longer False Clamp Latch Pins also see our Part Number P326 and Part Number P327.
The price shown is for one assembly.
$55.00
This latch pin assembly locks into the false clamp pin on many different sizes of Polar paper cutters. The
overall length of the latch pin (including the threaded shank) is approximately 65mm long (2 9/16” long). The
main latch area is 8mm in diameter. As shown in the photo, this assembly includes the latch pin (206036),
the spring (205687), the knurled knob with lock pin (205527, 200787), and a self-locking hex nut.
Also see our Part Number P325 and Part Number P327 for other length Polar False Clamp Latch Pins.
$55.00
LTD
This latch pin assembly locks into the false clamp pin on the larger sizes of Polar paper cutters. The
overall length of the latch pin (including the threaded shank) is approximately 70mm long (2 3/4” long). The
main latch area is 8mm in diameter. As shown in the photo, this assembly includes the latch pin, the spring
(205687), the knurled knob with lock pin (205527, 200787), and a self-locking hex nut.
Also see our Part Number P325 and Part Number P326 for other sizes of Polar False Clamp Latch Pins.
$55.00
SNC - Clamp Pedal Cam Wedge (three tapped holes)
Clamp Pedal Cam Wedge, for Polar 92 EMC II to Polar 155 EMC II Paper Cutters. This solid nylon wedge
measures 20mm X 47mm X 60mm long (.79” x 1.85” x 2.36”). It has three molded in threaded brass inserts
with M6 threads. These are used on many of the Polar EMC 2 models. Also see our part number SW for our
nylon one hole wedge. (017085, 033268)
$39.00
SP182 - Split Pulley Shim
Shim for V Belt Split Pulley for Polar CE Paper Cutters. (206640, 266641) This laser cut steel shim is used
between the adjustable pulleys on Polar Model CE hydraulic pump output shafts. These shims are added and
removed to ensure the correct tension is maintained on the belt. These shims fit both the original Polar split
pulleys, and our replacement pulleys. Each shim measures .5mm thick (.020”). They are sold individually.
$9.00
SP187 - Polar Split Pulley Assembly - Short Hub
V Belt Split Pulley Assembly for Polar CE Paper Cutters. (010280, 010127) This precision machined
aluminum split pulley is a direct replacement for the original die cast pulley used on the tapered output shaft
on the Polar Model CE hydraulic pump. Included is both pulley halves, three steel adjusting shims (our part
number SP182), and the three bolts to hold the two halves together. Each shim is .5mm (.020”) thick. The
pulleys have threaded steel inserts installed where the two pulley halves bolt together, similar to the originals, to prevent the threads from stripping. This is the “Short Hub” version of this pulley assembly. The hub
length measures approximately 1/2”. (See our part number SP188 for the 7/8” long “Long Hub” version.)
$325.00
SP188 - Polar Split Pulley Assembly - Long Hub
V Belt Split Pulley Assembly for Polar CE Paper Cutters. (010280, 010127) This precision machined aluminum split pulley is a direct replacement for the original die cast pulley used on the tapered output shaft on the
Polar Model CE hydraulic pump. Included is both pulley halves, three steel adjusting shims (our part number
SP182), and the three bolts to hold the two halves together. Each shim is .5mm (.020”) thick. The pulleys
have threaded steel inserts installed where the two pulley halves bolt together, similar to the originals, to
prevent the threads from stripping. This is the “Long Hub” version of this pulley assembly. The hub length
measures approximately 7/8". (See our part number SP187 for the 1/2" long “Short Hub” version.)
$325.00
LTD
SW - Clamp Pedal Cam Wedge (single tapped hole)
Clamp Pedal Cam Wedge, for Polar Paper Cutters (205844). This nylon wedge measures 3/4” X 1” X 2-7/16”
long. It has a molded in threaded brass insert with an M8 thread. It mounts on the clamp shaft bracket on
the larger Polar cutters made between approximately 1968 through 1982, such as the Polar EL and Polar CE
models. Also see our part number SNC for the three hole clamp pedal cam wedge.
$31.00
W10 / Polar Blade Leveling Handle, for 14mm square shaft
Blade leveling handle for many Polar Paper Cutters. (224707) This malleable iron blade leveling handle is
used on many models of Polar Paper Cutters including the Polar 115 EL. It is 6 1/2” long and has a 14mm
square hole which clamps on the square blade leveling shaft on the back side of the cutter.
$65.00
W19 / Polar Blade Leveling Handle, for 19mm square shaft
Blade leveling handle for many Polar Paper Cutters. This steel blade leveling handle is used on many larger
models of Polar Paper Cutters, up to and including the Polar 155. It is 9” long and has a 19mm square hole
which clamps on the square blade leveling shaft on the back side of the cutter.
$65.00
Polar Knife Bolts 19
Knife Bolts for Polar 107, Polar 112, Polar 115, Polar 137, Polar 145, Polar 150 & Polar 155 paper cutters.
Socket head cap screw, M12 x 22mm long (.87”) below the head. This bolt has a screwdriver slot cut in the
end as shown for ease of removal if the allen key socket gets stripped. Black oxide finish for corrosion
resistance. Also see our knife bolt part number B704 which fits newer models of Polar paper cutters.
$4.20
Knife Bolts for Polar 80, 82, 90 & 92 paper cutters (200962). These Grade 12.9 socket head cap screws
have an M10 thread. They are 16mm long (.63”) below the head and have a black oxide finish for corrosion
resistance.
$3.30
B66 - Polar 92 Knife Bolt
Knife Bolts for some Polar 92 Paper Cutters. This steel, low head, hex head bolt fits some Polar 92 Paper
Cutters. It has a 10mm thread and measures 20mm (.79”) long below the washer. The heavy steel washer is
1” in diameter and 1/8” thick. The washer also has a beveled outer edge. The washer rotates in place but is
held captive, it will not fall off.
$12.58
Knife Bolts for Polar 76, Polar 76 EM and some Polar 72 (28”) Paper Cutters (014116, 021053) Socket head
cap screw, 10mm thread by 21mm long (.83”) below the washer. It has a 1” diameter washer which is 1/4”
thick and has been counter bored 1/16” deep to fit the head. The washer is held captive by a snap ring. See
our part number B522 for a shorter version of this same bolt. Be sure to check your existing bolt length.
Order these by the bolt length under the washer, not by the Polar model number.
$13.44
Knife Bolts for Polar 55, Polar 66, Polar 71 and some Polar 72 (28”) Paper Cutters (014775, 014776, 021054,
200276) Socket head cap screw, 10mm diameter thread by 17mm long (.67") below the washer. It has a 1"
diameter washer which is 1/4” thick and has been counter bored 1/16” deep to fit the head. The washer is
held captive by a snap ring. See our part number B521 for a longer version of this same bolt. Order these by
the bolt length under the washer, not by the Polar model number.
$13.44
Knife Bolts for Polar X, XT, E and ED Paper Cutters (409569, 419520). These zinc plated, grade 12.9, hex
head cap screws have a 12 mm diameter thread. Included with each bolt is a heavy 4mm thick zinc plated
washer made from heat treated 4140 steel. These blade bolts are 24.5mm long below the washer. The washer
is threaded to keep it in place. These knife bolts fit the following Polar Paper Cutters: 78X, 78XT, 78E, 78ED,
78ES, 92X, 92XT, 92E, 92ED, 115X, 115XT, 115E, 115ED, 137X, 137XT, 137E, 137ED, 155X, 155XT, 155E,
155ED, 176X, 176XT, 176E, 176ED. Also see our part numbers B46, B47, B66, B521, and B522 for knife bolts
which fit older models of Polar Paper Cutters.
$11.50
LTD
Knife Change Handles 20
H63 - Challenge Knife Change Handle
Knife Changing Handle for Challenge Paper Cutters. This knife changing handle also fits Baumfolder paper
cutters. The solid steel knife handle is 4-5/8” long and is machined from one solid piece of bar stock. The
knurled handle section is 5/8” diameter. The threaded section is 3/8”-16 by 7/8” long.
$16.50
H64-12 - Challenge, Lawson, Seybold Knife Change Handle
Knife Changing Handle for Challenge/Lawson/Seybold Paper Cutters. This solid steel handle is 6-1/4” long.
The 7/8” diameter shank is knurled over most of its length for a solid grip. The thread on this handle is
1/2"-12. (See our part number H64-13 for the same handle with a 1/2”-13 thread.)
$32.50
H64-13 - Challenge, Lawson, Seybold Knife Change Handle
Knife Changing Handle for Challenge/Lawson/Seybold Paper Cutters. This solid steel handle is 6-1/4" long.
The 7/8” diameter shank is knurled over most of its length for a solid grip. The thread is 1/2"-13 on this
handle. (See our part number H64-12 for the same handle with a 1/2"-12 thread.)
$23.50
H69 - Triumph Knife Changing Handle
Triumph Paper Cutter Knife Changing Handle. This solid steel knife changing handle is 5-3/8" long and fits
most Triumph paper cutters. The 1/2" diameter shank is knurled over most of its length for a slip resistant
grip. It has a black oxide finish for corrosion protection. The thread is an M10 x 1.5mm which is 20mm
long (.79"). The pointed end helps with blade alignment during installation. Made in USA. Also see our other
Triumph knife changing handle, part number H70.
$16.00
H70 - Triumph Knife Changing Handle
Triumph Paper Cutter Knife Changing Handle. This knife changing handle has a 2-5/8" long steel stud. It has a
10mm x 1.5mm thread to fit most Triumph paper cutters. The fluted plastic hand grip is 2-5/8" long. Made in
USA. Also see our other Triumph knife changing handle, part number H69.
$16.90
H72 - Pivano Knife Changing Handle
Knife Changing Handle for Pivano Paper Cutters. This steel handle is machined from one piece of cold rolled
hex bar stock. The threaded end has a 12mm x 1.5mm thread. The overall length is 6" and the hex handle is
5/8" across the hex.
$22.50
LTD
Knife Change Handles 21
K15 - Polar Blade Change Support Handle
Knife Changing Support Handle for use on Polar 72 CE, 76 EM and Power Max 28 Paper Cutters.
(010755) The 10mm diameter pin on this 10” long steel blade support handle is inserted in a hole in
the guide on the right side of the table. The nose of the blade support handle is then rotated up against
the front face of the blade. This helps keep the blade in place as the knife bolts are removed or installed. Changing the blade without this blade support tool creates an unsafe condition.
$63.00
Knife Changing Handle for most Polar 71, 72, 76, 82 & 92 Paper Cutters (206579). This solid steel handle
is 5” long. The 1/2” diameter shank is knurled over most of its length for a slip resistant grip. It has a black
oxide finish for corrosion protection. The thread is an M10 x 1.5mm which is 12mm long (.47”).
$16.00
Knife Changing Handle for most Polar 107, 112, 115, 137, and 155 Paper Cutters. This solid steel handle is
5" long. The 1/2" diameter shank is knurled over most of its length for a slip resistant grip. It has a zinc plated
finish for corrosion protection. The thread is an M12 x 1.75mm which is 12mm long (.47”).
$16.00
Knife Changing Handle for Polar 107, 112, 115, 137 and 155 Paper Cutters. (207315) This solid heavy duty
steel handle is 7-1/2" long. The 1” diameter shank is knurled over most of its length for a better grip. The
thread is an M12 x 1.75mm which is 14.5mm long (.57"). This heavy blade change handle (weights almost
1-1/4 pounds) is machined from one piece of solid steel bar stock and is zinc plated for corrosion protection.
It is often used in conjunction with our blade stand, part number BS10.
$35.00
Knife Changing Handle for Polar 82 EL, Polar 82 ST, and Polar 86 EL Paper Cutters. (010660) These handles
or blade supports have a 7/8" long, M10 steel stud. They have a 1.5mm thread pitch. It is used for knife
changing on most Polar EL models of paper cutters. The hand grip is made of phenolic plastic and the disk is
a semi-hard plastic.
$34.00
LTD
Knife Changing Knobs 22
K10 - Lawson Knife Change Knob
Concentric Knife Changing Knob for Lawson Paper Cutters. This cast aluminum knob is 2-1/2” in diameter,
plus the thickness of the rubber o-ring. It has a fixed threaded steel stud. The steel stud has a 1/2”-13 thread
and is mounted in the center of the aluminum knob. It is used to change the blade on Lawson paper cutters.
$30.00
K11 - Lawson Knife Change Knob
Eccentric Knife Changing Knob for Lawson Paper Cutters. This cast aluminum knob is 2-1/2” in diameter,
plus the thickness of the rubber o-ring. It has a threaded steel stud which can be rotated by turning the steel
cross pin. The steel stud has a 1/2”-13 thread and is mounted off center from the center of the aluminum
disc. This makes it possible to rotate the knob, once it has been screwed into place, so as to put light pressure against the blade before the blade is loosened in the blade carrier.
$34.00
K12 - Seybold Knife Changing Handle
Knife Changing Knob for Seybold Paper Cutters. This cast aluminum knob is 2-1/2” in diameter. It has a fixed
steel stud with a 3/8”-16 thread which fits many models of Seybold Paper Cutters.
$21.80
K13 - Seybold Knife Changing Knob
Knife Changing Knob for Seybold Paper Cutters. This cast aluminum knob is 1-7/8” in diameter. (Similar to
our part number K12) It has a fixed steel stud with a 3/8”-16 thread.
$16.40
K14 - Polar Knife Changing Handle
Knife Changing Handle or support for Polar 90EL, 90CE, 92CE, 112ST, 115CE, 115EL (late models) & 155CE
Paper Cutters. (010113, 206579) This “insert and twist” type blade support handle has a solid nylon plastic
body with a plastic handle. The steel shaft is 10mm (.39”) in diameter with a fixed solid steel 4mm diameter
pin for sliding down the slot. It is used for blade changing on most Polar 90 EL, 90 CE (later models), 92 CE,
112 ST, 115 CE, 115 EL later models & 155 CE paper cutters. These all require this twist type blade support
for use during knife changes.
$35.00
LTD
Knife Bolt T Wrench 23
W71 - Knife Bolt Wrench (3/8" hex)
“T” Wrench for changing knife blade bolts in paper cutters. 3/8” hex x 17” long. This welded all steel “T”
wrench has a quality steel 3/8” hex key stock installed in the end of its shaft. Made in USA.
$51.00
$51.00
W73 - Knife Bolt Wrench (8mm hex)
“T” Wrench for changing knife blade bolts in paper cutters. 8mm hex x 17” long. This welded all steel “T”
wrench has a quality steel 8mm (.315”) hex key stock installed in the end of its shaft. Made in USA.
$51.00
“T” Wrench for changing knife blade bolts in paper cutters. (224304) 10mm hex x 24” long. This welded
all steel “T” wrench has a quality steel 10mm (.394”) hex key stock installed in the end of its shaft. Made
in USA.
$51.00
“T” Wrench for changing knife blade bolts in paper cutters. 8mm hex x 21” long. (010859) This welded
all steel “T” wrench has a quality steel 8mm (.315”) hex key stock installed in the end of its shaft. Made
in USA.
$51.00
$51.00
“T” Wrench for changing knife blade bolts in paper cutters. 10mm hex x 17” long. This welded all steel
“T” wrench has a quality steel 10mm hex key stock installed in the end of its shaft. Made in USA.
$51.00
W78 - Knife Bolt Wrench (5/8" socket hex)
“T” Wrench for changing knife blade bolts in paper cutters. 5/8” socket by 16” long. This welded all steel
“T” wrench has a quality steel 5/8” socket welded to the end of its shaft. Made in USA. Fits our blade bolt
number B42.
$48.57
W79 - Knife Bolt Wrench (11/16" socket)
“T” Wrench for changing knife blade bolts in paper cutters. 11/16” socket by 16” long. This welded all
steel “T” wrench has a quality steel 11/16” socket welded to the end of its shaft. Made in USA. Fits our
blade bolt number B43.
$48.57
LTD
Knife Bolt T Wrench 24
W80 - Knife Bolt Wrench (for 5/8" square head bolt)
“T” Wrench for changing knife blade bolts in paper cutters. 16” long. This welded all steel “T” wrench
has a quality steel socket welded to the end of its shaft to fit on 5/8” square head bolts. Made in USA. Fits
our blade bolt number B41.
$48.57
LTD
Clutch Handels 25
CH1 - Polar Clutch Handle
Clutch Handle for Polar 71 CE, Polar 72 CE, and Power Max 28 paper cutters. (013819) These “T wrench”
style clutch handles are made of 4140 steel with 8mm precision cut metric threads. They have a black oxide
finish for corrosion protection. These replace the original yellow plastic style handle. These are normally used
in pairs but are sold individually. Price is per piece.
$40.00
Clutch Handle for Polar 76 EM paper cutters. (017490) These “T wrench” style clutch handles are made of
4140 steel with 8mm precision cut metric threads. They have a black oxide finish for corrosion protection.
These replace the original yellow plastic style handle. These are normally used in pairs but are sold individually. Price is per piece.
$40.00
Clutch Handle for Polar 82 EL paper cutters. These “T wrench” style clutch handles are made of 4140 steel
with 8mm precision cut metric threads. They have a black oxide finish for corrosion protection. These replace
the original yellow plastic style handle. These are normally used in pairs but are sold individually. Price is per
piece.
$40.00
with 8mm precision cut metric threads. They have a black oxide finish for corrosion protection. These replace
the original yellow plastic style handle. These are normally used in pairs but are sold individually. Price is per
piece.
$40.00
Clutch Handle for Polar 92 CE, Polar 92 EMC, and Polar 92 ED paper cutters. (010958) These “T wrench”
style clutch handles are made of 4140 steel with 8mm precision cut metric threads. They have a black oxide
finish for corrosion protection. These replace the original yellow plastic style handle. These are normally used
in pairs but are sold individually. Price is per piece.
$40.00
with 8mm precision cut metric threads. They have a black oxide finish for corrosion protection. These
replace the original yellow plastic style handle. These are normally used in pairs but are sold individually.
Price is per piece.
$40.00
LTD
Clutch Handels 26
with 10mm precision cut metric threads. They have a black oxide finish for corrosion protection. These
replace the original yellow plastic style handle. These are normally used in pairs but are sold individually.
Price is per piece.
$43.00
Clutch Handle for Polar 115 CE, 115 ED, and 115 XT paper cutters. These “T wrench” style clutch handles
are made of 4140 steel with 10mm precision cut metric threads. They have a black oxide finish for corrosion
protection. These replace the original yellow plastic style handle. These are normally used in pairs but are sold
individually. Price is per piece.
$44.00
Clutch Handle for Polar 115 EMC paper cutters. These handles also fit the Prism 115 QZK paper cutters.
These “T wrench” style clutch handles are made of 4140 steel with 10mm precision cut metric threads. They
have a black oxide finish for corrosion protection. These replace the original yellow plastic style handle. These
are normally used in pairs but are sold individually. Price is per piece.
$44.00
Clutch Handle for Polar 115 MON, Polar 115 EL, Polar 150 EL, Polar 155 EMC, Polar 155 MON, and Polar 155
CE paper cutters. (010231) These “T wrench” style clutch handles are made of 4140 steel with 10mm
precision cut metric threads. They have a black oxide finish for corrosion protection. These replace the
original yellow plastic style handle. These are normally used in pairs but are sold individually. Price is per piece.
$45.00
Clutch Handle for Polar 137 ED, Polar 137 X and Polar 137 XT paper cutters. These “T wrench” style clutch
handles are made of 4140 steel with 10mm precision cut metric threads. They have a black oxide finish for
corrosion protection. These replace the original yellow plastic style handle. These are normally used in pairs
but are sold individually. Price is per piece.
$45.00
Book Clamps 27
C81 - Book Clamp (1 pair)
“Economy” style spine clamp or book clamp for paper cutter back gauge. Sometimes called book
trimming guides, these book clamps keep books and other stapled or stitched booklets flat for
accurate and square cutting. They are very effective at assuring an even cut by holding down the
spine of a book. The book clamps install on the guillotine paper cutter back gauge by tightening them to the back gauge ribs. They are made of cast bronze and are usually installed in pairs.
PRICE IS PER PAIR. Add “1” to the shopping cart for 1 pair.
$33.00
C90 - Book Clamp (1 pair)
“Challenge” style spine clamp or book clamp for paper cutter back gauge. Sometimes called book
trimming guides, these spine clamps keep books and other stapled or stitched booklets flat for
accurate and square cutting. They are very effective at assuring an even cut by holding down the
spine of a book. The book clamps install on the guillotine paper cutter back gauge by tightening them to the back gauge ribs. They are made of cast bronze and are usually installed in pairs.
PRICE IS PER PAIR. Add “1” to the shopping cart for 1 pair.
$39.40
LTD
Misc Parts 28
AC10 - Angle Cutter Guide
Angle Cutter Guide for Guillotine Paper Cutters. This aluminum angle cutting guide is quick and easy to
install. The two clamps attach to the paper cutter back gauge ribs. Once it is secured in place it will not slip
out of position, as some single clamp guides are prone to do. It is fully adjustable for cutting any angle from
0 to 90 degrees. Once it is set in position it will allow for repeated cuts at the same angle. It will
accommodate a stack of paper or card stock up to 2-5/8” high. A box end wrench is included with each
guide to aid in installation and adjustment.
$112.50
AH - Wohlenberg Blade Leveling Handle
Wohlenberg Blade Leveling Handle. This aluminum handle replaces the original plastic blade leveling handle
on Wohlenberg Paper Cutters. It has an aluminum body with a stainless steel and plastic handle.
$180.00
AJ102 - Lawson Seybold Air Jet - Long Body
This brass air jet or air nozzle is used in air tables on Seybold, Lawson, and other paper cutters. It is 1-7/8"
long x 9/16” diameter. One end of the air jets are knurled for a press fit in a 9/16" diameter reamed hole in the
paper cutter table. The opposite end has two machined wrench flats and a 1/8" NPT for the air supply.
$21.50
AJ103 - Lawson Seybold Air Jet - Short Body
This brass air jet or air nozzle is used in air tables on Seybold, Lawson, and other paper cutters. It is 1-3/8"
long x 9/16" diameter. One end of each of the air jets are knurled for a press fit in a 9/16" diameter reamed
hole in the paper cutter table. The opposite end has two machined wrench flats and a 1/8" NPT for the air
supply.
$20.40
AJ603 - Wohlenberg Air Jet Nozzle
This plastic air jet or air nozzle is used in air tables on Wohlenberg paper cutters. It has a spring loaded
stainless steel ball. These air jets are 16mm in diameter (.630") at the large end by 34mm long (1.34") when
measured over the stainless steel ball.
$9.30
B3 - Torx Plus Bit
This Torx Plus Bit fits our B60, B61, B63 and B64 blade bolts for Wohlenberg and other paper cutters. It
accepts a standard 3/8" square ratchet or socket extension. Torx and Torx Plus bits are not designed to be
interchangable. While a Torx bit will also fit these bolts, it is a loose fit and will strip the bolt heads. Never
use a Torx bit in a Torx Plus bolt.
$26.00
BB120 - Lawson Shear Block
Bronze Shear Block for Lawson paper cutters. 2BA2026 This guide block or shear block measures
approximately 2.5" wide x 4" long. The main cross hole measures 1-1/4" in diameter. It is used in Lawson
Pacemaker cutters and Lawson cutters 52 through 70.
$260.00
LTD
Misc Parts 29
BB121 - Lawson Shear Block
Bronze Shear Block for Lawson paper cutters. This guide block or shear block measures approximately 2.5”
wide x 4” long. The main cross hole measures 1-1/2” in diameter. It is used in Lawson cutters 87 through 110.
$268.00
HB16 - Clutch Handle Helper Bar
These steel bars are used to turn the clutch handles when they are screwed into the flywheel on Polar paper
cutters. The holes for the clutch handles are 6-3/8” apart. Without this tool you risk applying uneven pressure
to the clutch handles which can cause them to break off.
$35.00
M615 - Oliver 510 Drill Pointer Manual
This is a copy of a manual for an Oliver 510 Drill Pointer or drill sharpener. Titled “Directions for Operation
Oliver 510 Drill Pointer” it was originally printed in 1955. The manual contains approximately 16 pages. It
contains a parts drawing with part numbers as well as the following sections:
Introduction, Greasing the Chuck, Operating Instructions, Dress the Wheel, To Grind a Drill, Parts List, To
Change the Clearance, To Change the Chisel Point Angle, Grinding 3 and 4 Lip Drills, To Grind Drills Off
Center, Water Attachment, If Point Does Not Look Right, Checking Drills, Web Thickness of Drills,
Dry Grinding, Coolants
$38.50
M616 - Cincinnati Nos. 1-2-3-4 Dial Milling Machine Manual
This is a copy of a manual for a Cincinnati Milling Machine. It is titled “Service Manual and Repair Parts
Catalog, Cincinnati Nos. 1 - 2 - 3 - 4 Dial Type Milling Machines” (Medium Speed and High Speed)
The cover also reads “This service manual and repair parts catalog was made for the purpose of helping the
maintenance foreman, millwright and the operator to know the correct method of installing and caring for the
machine and to facilitate the ordering of repair parts.”
This is a clear copy of a manual which was printed in 1938. Contains a total of 85 pages. The pages are
installed in a three ring binder. It contains numerous drawings and photographs. The table of contents
contains the following sections:
Lubrication Chart for All Machines, Lubrication Instructions and Specifications, Nomenclature Chart
Installation Instructions, Adjusting the Gibs and Main Driving Clutch, Adjusting the Rapid Traverse Clutch,
Removing Leadscrew, Removing Table, Removing Universal Housing, Removing Cross Screw, Removing
Cross Screw Nut Bracket, Removing Saddle, Removing Spline Shaft Bracket, Removing Vertical Screw,
Removing Change Gear Bracket, Removing Lubricant Pump in Knee, Removing Knee, Removing Coolant
Pump, Removing Pulley Bracket, Removing Feed Box, Removing Gear Shifter Bracket, Removing Hand Feed
Worm Box, Removing Power Feed Worm Box, Removing Vertical Spindle, Removing Horizontal Spindle,
Removing Vertical Head, Adjustment of Spindle Bearings, Illustration of Front of Column, Removing the Back
Gear Shaft, Removi Other Drive Shafts, Removing More Than One Unit, Removing the Overarm, Removing
Rear Control Bracket.
$62.50

LTD SHEAR BOLTS

Transcription

Similar documents

LTD Saddlestitcher Parts