Installation Guide

Installation Guide
Wireless ADSL2+ Router
ZTE ZXV10 W300 v5.2/
ZXV10 W300B v5.2
Contents
Περιετόμενα
Minimum System Requirements .................................................................................................. .................................. 3
Package Contents ............................................................................................................ ................................................ 4
LED Indications .............................................................................................................................................................. 5
Ports ....................................................................................................................... .......................................................... 6
Connection of ADSL2+ Router ..........................................................................................................................................7
PSTN Line.................................................................................................................... .............................................. ... 8
ISDN Line ................................................................................................................... ................................................... 11
Internet Settings ............................................................................................................................. .......................... .... 14
Wireless Connection ....................................................................................................................................................... 19
Activation/Deactivation of Wireless Network & Reset of ADSL2+ Router ................................................................. 24
Change Internet access Username & Password ............................................................................................................. 25
Hardware Warranty ............................................................................................................................ ............................ 26
Online Security …........................................................................................................................................................... 26
Connection Data ............................................................................................................ ................................................. 27
Eλάτιστες
Απαιτήσεις
Σσστήματος
Minimum
System
Requirements
1. Processor Pentium 4
2. Windows XP/Vista/7 or Mac OS 9.x
3. 1 GB RAM
4. 25 MB free space on hard disc
5. Ethernet Network Card 10/100 Mbps
3
Περιετόμενα
Package
Contents Σσσκεσασίας
1 ADSL2+ Wireless Router
2 Phone Cables (RJ-11)
1 Ethernet Cable (RJ-45)
1 Installation CD
1 Power adapter
1 Splitter
Installation Guide
1 Filter (for PSTN)
4
LED Indications
There are the following LEDs in the front panel of the ADSL2+ Router. Check the meaning of
each LED below (Image 1).
LED
POWER
DSL
INTERNET
LAN1~LAN3
& STB
&
STB
WLAN
Color
Status
Description
Off
Power off
(Red) Blinking
Software upgrade in progress
(Green) On solid
Power is on
Off
Non detectable signal
(Green) Blinking
Router attempting to connect
(Green) On solid
Router is on
Off
System in bridge connection status or ADSL is not connected
(Green) Blinking
Partial data transmission through the Router
(Green) On solid
The system has an internet address and ADSL is connected.
IP data packets are transmitted normally.
(Red) On solid
The device attempted an IP connection and failed (no
DHCP response, no PPPoE response, PPPoE quality
check failed, no IP address from IPCP etc.)
Off
Ethernet interface is in non communication status
(Green) Blinking
Data received and transmitted through Ethernet
interface.
(Green) On solid
Ethernet is in communication status
Off
(Green) Blinking
Wi-Fi interface is off
Data received and transmitted through Wi-Fi
interface
(Green) On solid
Wi-Fi interface is on
Image 1
5
Port connections
The ADSL2+ Router has the following switches and port connections (Image 2)
DESCRIPTION
OPERATION
POWER
Power Inlet
Connection with 220V power adapter
SWITCH
Power switch
Wireless network
button
Ethernet port
for connection of
decoder
LED
Wi-Fi
LAN4 (STB)
LAN1~LAN3
LINE
RESET
Ethernet port for
connection of PC
Port for telephone cable
connection (RJ-11)
Factory default reset
button
Turns router ON / OFF
Turns wireless network ON / OFF.
Connection with OTE subscription TV
over the Internet
Connection of up to three PCs for internet access
and creation of a local network
Connection with phone jack or splitter.
Resets default settings.
Image2
6
Connection of ADSL2+ Router
Connection of ADSL2+ Router
Follow the instructions below to connect the ADSL2+ Router over a PSTN
or ISDN phone line.
7
PSTN Line
If you have a PSTN phone line(simple analog line),
connect the ADSL2+ Router as shown below.
8
PSTN Line
You must unplug any other telephone device connected to the phone jack.
1
2
3
Use the blue cable to connect the blue port of the splitter to the
phone jack.
A. Use the grey cable to connect the grey port of the splitter to the
grey port on the Conn-x router.
B. Then connect the cable of your phone to the black port of the
splitter.
Use the yellow cable to connect the ETHERNET port on your
computer to one of the first three ports on the Conn-x router.
ATTENTION: The purple port (STB) is used only for
connection of a decoder required for the OTE subscription TV
over the Internet.
9
PSTN Line
4
Connect the power adaptor to the Conn-x power inlet and plug it in.
Press the power button SWITCH in the back panel of the router
to turn your router on.
The Power, DSL, Internet, LAN and WLAN LEDs will light up.
If you wish to connect additional phones to other plugs, you must
use a filter for each phone device. Connect your phone to the filter
and the filter to the phone jack.
Note: If your phone network is connected to any other device (alarm,
switchboard, etc.), you must use additional ADSL filter or splitter.
Please address a specialized crew.
10
ISDN Line
If you have an ISDN phone line,
connect the ADSL2+ Router
as shown below.
11
ISDN Line
1
2
Disconnect the phone cable from the ISDN (N.T. 1) device and
connect it to the black port of the splitter.
A. Use the blue cable to connect the blue port of the splitter to
the phone jack.
B. Use the grey cable to connect the grey splitter port to the grey
port on the Conn-x router.
Note: If your phone network is connected to any other device (alarm,
switchboard, etc.), you must use additional ADSL filter or splitter.
Please address a specialized crew.
12
ISDN Line
3
4
Use the yellow cable to connect the ETHERNET port on your
computer to one of the first three yellow ports of the Conn-x router.
ATTENTION: The purple port (STB) is used only for
connection of a decoder required for the OTE subscription TV
over the Internet.
Connect the power adaptor to the Conn-x power inlet and plug it in.
Press the power button SWITCH in the back panel of the router
to turn your router on.
The Power, DSL, Internet, LAN and WLAN LEDs will light up.
13
Internet Settings
Internet Settings
To install the ADSL2+ Router, insert the CD in your CD-ROM drive. The
CD should run automatically. If the CD does not run automatically, go to
Windows Explorer, select the CD-ROM drive where your CD is located,
double click on setup.exe and follow the instructions.
If you are not able to install the ADSL2+ Router through the CD, follow the
following instructions:
14
Internet Settings
11
Go to your Browser.
In the field “Address”
(Image 1) type
http://192.168.1.1 and
Press «Enter».
The next screen will
appear (Image 2):
Image 1
The indications for ADSL,
ATM and Internet Status
must be green.
If one of them is red, check
your cable connections and try
again.
Image 2
15
Internet Settings
2
Click on “Administration”.
The next screen will appear (Image
3):
Image 3
16
Internet Settings
In the field «Username»type «admin».
In the field «Password»type the password that is written on the
label on the underside of your ADSL2+ Router and click ΟΚ.
Make a note of the Username and Password on the last page
of this manual.
17
Internet Settings
3
The next screen will
appear (Image 4):
In the field «Username»fill in
the username provided to you
when you purchased Conn-x
package followed by
@otenet.gr
In the field «Password»fill in
the password provided to you
when you purchased Coon-x
package. Click «Apply»to
store the settings. You are now
connected to the Internet!
Close your Browser.
Image 4
18
Wireless Connection
Wireless Connection
Follow the following instructions for a wireless connection to the internet.
19
Wireless Connection
To make a wireless internet connection you must have completed the Internet Settings.
If you wish to make a wireless connection with a desktop computer, you must have a wireless USB stick or
wireless network card installed and activated on your computer.
If you wish to make a wireless connection with a laptop, you must first activate the wireless function (check your
laptop’s manual).
We suggest keeping the default settings to facilitate installation. You can change the settings afterwards through
the wireless network settings menu (check the user manual in the CD).
20
Wireless Connection
1
Double-click on the wireless network icon on your computer screen to see the
available wireless networks.
21
Wireless Connection
The name of your wireless network to look for is
the same as the SSID name that is written on the label
on the underside of your router or on the CD cover.
Make a note of the SSID name on the last page of the manual.
2
22
Click on the wireless network that corresponds to
your SSID name and click Connect.
Wireless Connection
3
In the screen that appears, enter the network security
key (WPA) which you can find on the label on the
underside of your router or on the CD cover with the
WPA name and click ΟΚ. Make a note of the
network security key (WPA) on the last page of the
manual.
Connecting to the network. Please wait...
You are now connected to the Internet! Attention! You must repeat the section Wireless Connection
or Connect Wirelessly from the installation CD for any additional devices you wish to connect
wirelessly.
23
Activation/Deactivation of Wireless Network & Reset of ADSL2+ Router
Wireless operation is activated. To deactivate it, press and hold
pressed the Wi-Fi button on the back of the ADSL2+ Router until
the WLAN LED on the front side of the ADSL2+ Router is off.
To activate wireless operation, press and hold pressed the same
button for more than 1 second. The WLAN LED will turn on.
If you wish to return your ADSL2+ Router to the default settings,
first make sure that the ADSL2+ Router is on. Press and hold
pressed the RESET switch on the underside of your ADSL2+
Router, until all LEDs are off.
Wait until the LEDs of the ADSL2+ Router turn back ON.
Resetting to default settings will delete any information you have
entered and stored in the ADSL2+ Router.
24
Change Internet access Username & Password
1
2
If you want to change the Username and Password (you can only change the Username once but
you can change the password as many times as you wish), open your web browser and on the
address line type http://www.oteshop.gr/myservices/myid
3
If you change the Username or Password, you must
repeat the Internet Settings.
In the webpage that appears, under
MY e-SERVICES or Internet Services Administration
click on Change of Conn-x name and password
and follow the instructions.
25
Equipment Warranty
Your equipment comes with a one (1) year warranty from the date of purchase.
Online Security
Conn-x offers you 2 months free Online Security for better and safer internet surfing and for protection of your
computer from viruses, hackers & spam e-mails. Online Security includes:
•
•
•
•
Anti-Virus: for protection against viruses, “worms”, trojans & spyware.
Firewall: to exclude unauthorized access.
Anti-Spam: to prevent e-mail spam.
Parental Control: to control and deny access to websites with undesired content such as: violence, adult
material, guns, drugs, etc.
Instructions:
To proceed to the Online Security installation, you must have first successfully completed the internet
connection procedure. Open your web browser and type www.conn-x.gr on the address line; go to Add-ons
from where you can download and install the Online Security Service by Conn-x.
26
You can fill in here your connection information:
Username
for Internet access
SSID code
Password
for Internet access
Network Security Key (WPA)
Online Security Registration key
Equipment Username
Equipment Password
27
APRIL 2011
Please recycle
24-hour Technical Support
For questionsandassistance
before and during ADSL installation call
(local rate for all Greece)