Carrier Project Model 104 Slider Belt

Model 104 Slider Belt Conveyor
Model Description:
The Model 104 Slider Bed Belt is designed with the systems approach in mind. The square head
and tail end terminals allow you the flexibility to combine this unit with other Titan units to
assure a continuous flow of material. The standard 4" deep formed 12-gauge frame allows
integration with several other types of conveyors available from Titan. Screw type take-ups and
4" diameter crown face pulleys are some of the standard design features. Modular design allows
you the flexibility to add additional sections if required. Your material handling requirements can
be solved by the experts at Titan.
1
MODEL 680
MULTI-STRAND CHAIN CONVEYOR
The Model 680 Multi strand chain conveyor is
used to convey products that are not conveyable
on a standard roller conveyor. The standard
chain is C2060 double pitch with a load capacity of 2,400 lbs. An optional C2080 double pitch
chain can be used for loads up to 4,000 lbs.
Optional low profile side mounted drive and additional strands of chain can be added to increase
load capacities.
MODEL 680 MULTI-STRAND CHAIN CONVEYOR
Standard
Options
(2) strands of C2060
C2080, multiple strands available
2,400 lbs
4,000 with (2) strands C2080
Drive
1 HP 230/460/3/60
Horsepower to fit application
Frame
Formed 7 ga.
Structural
30 F.P.M.
Specify
Chain
Capacity
Chain Speed
Optional
Drive location, HP, speed, variable speed available, controls, multiple chain strands, paint
NOTE: Specifications subject to change without notice
MODEL 680
MULTI-STRAND CHAIN CONVEYOR
BELT WIDTH + 9 3/8"
6"
BELT WIDTH
C-C
3 3 8"
5 3 4"
81 2"
SECTION A-A
SECTION B-B
OVERALL LENGTH
INFEED SECTION
DRIVE SECTION
18"
14"
A
B
1 13 32"
8 1 2"
20" MINIMUM
W/BOTTOM
9 9 32" MOUNT DRIVE
STD. IC60
REDUCER
A
B
MODEL 535
CHAIN DRIVEN LIVE ROLLER
CONVEYOR
The ultimate in heavy-duty conveying for pallets,
skids or drums - the Model 535 is designed to
handle extremely heavy loads. The 3 1/2” diameter x
.300 wall (schedule 80 pipe) rollers are rated
for 2500 lbs. per roller. The rollers use a heavy-duty
industrial, grease sealed, 1 1/16” hex bore
bearing. The Model 535 is available with either #60
or #80 roll-to-roll chain drives depending on chain
pull required. Standard construction is a 6” at #8.2
structural channel frame. This unit is available with
either a bottom mount or side mount drive. Supports
are structural channel (non-adjustable) with foot pads.
Roller centers are 6” for #60 chain drive and 6 1/2” for
#80 chain drive.
MODEL 535 CHAIN DRIVEN LIVE ROLLER CONVEYOR
Effective Widths
Lengths
Roller Size
Roller Centers
STANDARD
OPTIONS
15” to 66”
Customer can specify
Per application - 5’ Minimum
3’ minimum, maximum length based on application
3 1/2” dia. x .300 wall 1-1/16” hex shaft
(#2500 roll rating)
6”
Roller centers of 6”, 9”, 10-1/8”, 12” with #60 sprockets,
#80 roll-to-roll chain drive with roller centers of 6-7/16”,
9-7/16”, 12-7/16”
Frame
Structural channel
Drive
3/4 H.P. 230/460/3/60
1, 1-1/2, 2, 3, 5 HP, 115/230/1/60, 575/3/60, severe duty,
inverter duty, brake motor
#60
#80
Chain Drive
OPTIONAL
Roller Space - Consult factory, Roller Center - Consult Factory, Drive locations: as needed, Galvanized or stainless construction, H. P. , Speeds, Variable speed, Controls, Paint, 2 or 3 strand chain transfers, Pallet lifts, “C” Face brake and
Fixed end stop, Rollers set low, UHMW sleeves, Galvanized rollers, accumulation sleeves, Knee braces, Air operated
blade stop, Supports - 6” @ #8.2 structural channel, Pop-up roller, blade stops, pallet lifts.
NOTE: Specifications subject to change without notice
MODEL 535
CHAIN DRIVEN LIVE ROLLER CONVEYOR
10'
6" STANDARD CENTERS
IC-70
OPTIONAL ROLLER CENTERS
5 5/8" CENTERS
6 3/8" CENTERS
6 3/4" CENTERS
7 1/8" CENTERS
30"
STANDARD
STANDARD 10' LG. CONVEYOR SECTION W/#60 CHAIN DRIVE
1 29/32"
EFFECTIVE
WIDTH
6 15/16"
2 1/8"
8 1/2"
3/8"
8 1/2"
60A20 SPROCKETS
ROLLERS SET HIGH
5 1/4"
2 1/8"
ROLLERS SET LOW
C6 x #8.2 CHANNEL
19 1/2"
23"
STANDARD BOTTOM MOUNT DRIVE
13"
STANDARD SIDE MOUNT DRIVE
14"
9'- 9"
6 1/2" STANDARD CENTERS
OPTIONAL ROLLER CENTERS
7" CENTERS
7 1/2" CENTERS
8" CENTERS
8 1/2" CENTERS
IC-70
30"
STANDARD
STANDARD 9'-9" LG. CONVEYOR SECTION W/#80 CHAIN DRIVE
1 29/32"
EFFECTIVE
WIDTH
C8 x #11.5 CHANNEL
1 5/8"
7 1/4"
1 7/8"
8 1/4"
3/8"
ROLLERS SET HIGH
80A16 SPROCKETS
ROLLERS SET LOW
C6 x #8.2 CHANNEL
20 7/8"
22 3/4"
STANDARD BOTTOM MOUNT DRIVE
12 15/16"
14"
STANDARD SIDE MOUNT DRIVE
[Type here]
Turn Table On Shuttle
Model Description:
When your plant layout requires a directional change in the smallest possible space of your
conveyor system, you should consider using a Titan Powered Turntable. The turntable conveyor
can be used for product sortation, accumulation as well as directional changes. The Titan
Turntable is available in sizes ranging from 2' diameter to 12' diameter. The standard table top is
7-gauge construction with angle iron supports. The top is driven by either chain and sprockets or
air operated cylinder. The unit is furnished with expanded metal guards on all four sides. The
unit can be supplied with chain and sprocket drive, air operated for 90 degrees’ rotation or no
drive for manual indexing. Tops can be fitted with gravity roller or chain driven live roller
conveyor to suit your application.
3
[Type here]
Model 425
Model 425 Gravity Roller Conveyor Specifications:
Axle: 11/16" Hex
Roller Rating: 625 lbs.
Capacity: 580 lbs
Rollers: 2-1/2" Diameter x 11 Gauge
Frame: Formed 7 gauge
Shaft: 11/16" hex
Minimum Centers: 3"
4
[Type here]
525 V-Belt
Model MDR Poly V-Belt Motor Driven Roller Conveyor Specifications:
Bearings: Grease Sealed
Chain: #50 Roll-to-Roll Drive
Drive: 24 Volt DC
Frame: Formed 7 Gauge
Rollers: 2-1/2" dia. x 11ga. or 2-5/8" dia. x
7 ga. or 1.9" dia. x 16 ga./Spring Loaded
7/16" Hex Shaft
Speed: Specify
Supports: "H" Type
Paint: One Coat Industrial Enamel
5
[Type here]
525 CDLR W/ Iron Cross
525 CDLR
Model Description:
The Model 525 is designed to handle heavy loads including skids, drums, and pallets. This unit
incorporates a number 50 chain with a roll-to-roll drive. The frame is a heavy formed 7 gauge
construction with a one piece chain guard. Rollers are 2-1/2" diameter x 11 gauge (580 lb.
capacity) centers are 2-13/16", 3-7/16", 4-3/8", 5", 5-15/16" and 10".
Standard floor supports supplied are adjustable for approximately 30" to the top of roller. This
model is available in lengths to meet your needs (min length: 4-1/2"). Consult the factory for
further details.
6
MODEL 525
CHAIN DRIVEN LIVE ROLLER
The Model 525 Chain Driven Live Roller
conveyor from RSI, Inc. is designed
to handle heavy loads such as pallets, skids
or drums. The unit incorporates a number
50 chain with a roll-to-roll drive. The frame
is a heavy formed 7 gauge construction with
a one piece chain guard. Rollers are 2-1/2”
diameter x 11 gauge (580 lb. capacity). The
standard drive is a 3/4 H.P. for 30 F.P.M. roller
speed. A wide range of standard effective
widths are available. Standard roller spacings
are 2-13/16”, 3-7/16”, 4-3/8”, 5”, and 5-15/16”.
Floor supports are optional. The Model 525
comes in lengths to suit with a minimum length
of 4’ long.
Consult the factory for further details.
MODEL 525 CHAIN DRIVEN LIVE ROLLER CONVEYOR SPECIFICATIONS
Effective Widths
Lengths
Roller Size
Roller Center
Standard
Options
13” to 40”
Specify up to 40” E.W.
5’ min.
3’ min., max. based on application
2 1/2” Dia. x 11 ga. with 11/16” hex shaft 580 lb. roller cap.
5”
2-13/16”, 3-7/16”, 4-3/8”, 5-15/16”, 10”
Frame
Formed 7 ga.
Drive
3/4 H.P. 230/460/3/60
1, 1-1/2, 2, 3 H.P. 230/460/3/60, severe
duty, inverter duty, brake motor
#50
#60 available
Chain Drive
OPTIONAL
Roller Space - Consult factory, Roller Center - Consult Factory, Drive locations: as needed, Galvanized or stainless
construction, H. P. , Speeds, Variable speed, Controls, Coated rollers, Paint, 2 or 3 strand chain transfers, Pallet lifts,
Pallet jack plates for side or end load, “C” Face brake and Fixed end stop, Rollers set low, UHMW sleeves, Accumulation sleeves, Knee braces, Air operated blade stop, Supports - 6” @ #8.2 structural channel,
NOTE: Specifications subject to change without notice
MODEL 525
CHAIN DRIVEN LIVE ROLLER CONVEYOR
FIGURE "A"
OVERALL LENGTH
13"
OPTIONAL
SUPPORTS
18 3/8" (IC-60)
19 1/2" (IC-70)
20 7/8" (IC-80)
REDUCERS
FIGURE "B"
FIGURE "C"
5 5/16"
5 5/16"
EFFECTIVE WIDTH
1 1/2"
3 1/2"
EFFECTIVE WIDTH
1 11/16"
5 13/16"
1 1/2"
3/8"
1 11/16"
5 13/16"
ROLLERS SET LOW
ROLLERS SET HIGH
FIGURE "D"
FIGURE "E"
1"
STANDARD BOTTOM
MOUNT DRIVE
18 13/16"
15 13/16"
8"
11 1/2"
8 5/16"
FIGURE "F"
6 1/2"
1 11/16"
STANDARD SIDE MOUNT DRIVE
FIGURE "G"
3 1/2"
EFFECTIVE WIDTH
5 5/16"
1 11/16"
5 13/16"
5 13/16"
DOUBLE WIDE CHAIN GUARD
(STANDARD CENTERS - 3 7/16")
DOUBLE DRIVE GUARD
(STANDARD CENTERS - 2 13/16")
[Type here]
45 Degree Plastic Belt
The Series 2100 Flat Top Zero Tangent Radius belt is
designed specifically for curved conveyance, free of
straight sections, maximizing all available space. The
S2100 has a smooth, closed-top surface that can handle
a variety of package sizes, types, and configurations,
and is able to maintain product orientation and spacing
through its curves. Its compact design provides flexibility,
simplifying layout design and conveyor installation.
• Patent-pending, symmetric drive design simplifies
installation
• Lug-tooth style sprockets and positive drive system
provide improved reliability and durability
• Modular belt construction reduces maintenance time
and cost
Contact Intralox today for a sample of this new product
or for more information.
7
POWER TURNTABLE
When your plant layout requires a directional change in the smallest possible space, you should
consider using a RSI Powered Turntable. The turntable can be used for product sortation,
accumulation as well as directional changes. The RSI Turntable is available in sizes ranging from
2’ diameter to 10’ diameter. The standard table top is 7 gauge construction with angle iron supports.
The top is driven by either chain and sprockets or a contact wheel. The unit is furnished with
expanded metal guards on all four sides. Roller supports supplied as optional equipment. The unit
can be supplied with chain and sprocket drive, air operated for 900 rotation or no drive for manual
indexing. Tops can be fitted with gravity roller or chain driven live roller conveyor to suit
your application
POWERED TURNTABLE
SPECIFICATIONS
DRIVE:...................................................................................................................1/2 H.P. 230/460/3/60
SPEED: .......................................................................................................... 2.5 R.P.M. at Outside Rim
FRAME: ............................................................................................. 7 Gauge Top with Angle Iron Base
BEARINGS: ..................................................................................................................... Grease Sealed
SUPPORTS: ........................................................................................................ Fixed for 30” Elevation
PAINT:.......................................................................................................... One Coat Industrial Enamel
NOTE: Specifications subject to change without notice
POP-UP TRANSFER, POP-UP STOPS,
PALLET CENTERING, PALLET LIFT
and PALLET CROWDER OPTIONS
Designed to handle heavy duty loads such as
pallets, skids and drums. Heavy duty construction with #50 toll-to-roll drive chain. (#60 chain optional.) Standard rollers are 2 1/2” diameter x #11
gauge or 2 5/8” diameter x #7 gauge. Standard
roller centers are 5”. Supports are 4” structural
with adjustable feet.
MODEL 525 CHAIN DRIVEN LIVE ROLLER CONVEYOR SPECIFICATIONS
Effective Widths
Lengths
Roller Size
Roller Center
Standard
Options
13” to 40”
Specify up to 72” E.W.
5’ min.
3’ min., max. based on application
2” Dia. x 11 ga. with 7/16” hex shaft - 580 lb. roller cap.
5”
2-13/16”, 3-7/16”, 4-3/8”, 5-15/16”, 10”
Frame
Formed 7 ga.
6” C structural
Drive
3/4 H.P. 230/460/3/60
1, 1-1/2, 2, 3 H.P. 230/460/3/60, severe
duty, inverter duty, brake motor
#50 roll to roll drive
#60 available
Chain Drive
OPTIONAL
Roller Space - Consult factory, Roller Center - Consult Factory, Drive locations: as needed, Galvanized or stainless
construction, H. P. , Speeds, Variable speed, Controls, Coated rollers, Paint, multi-strand chain transfers, Pallet lifts, Pallet jack plates for side or end load, “C” Face brake and Fixed end stop, Rollers set low, UHMW sleeves, Accumulation
sleeves, Knee braces, Air operated blade stop, Supports - 6” @ #8.2 structural channel,
NOTE: Specifications subject to change without notice
POP-UP TRANSFER, POP-UP STOPS, PALLET CENTERING,
PALLET LIFT and PALLET CROWDER OPTIONS
Chain Driven Live Roller Conveyor
with Pop-Up Pallet Lift
Chain Driven Live Roller Conveyor with
Pallet Centering device - Pallet Crowder also available
Overall Length
3 1/2"
Overall Length
3 1/2"
21 15/16"
21 15/16"
18"
30"
Standard
18"
30"
Standard
Effective Width
Effective
Width
1 1/2"
3 3/4"
3 1/2"
1 11/16"
1 13/16"
Effective Width
3/8"
14"
Effective
Width
1 1/2"
3 3/4"
End View
NOTE: Pop-up Travel Chain Approximately 34" above roller
3 1/2"
1 11/16"
1 13/16"
Rollers Set High
3/8"
14"
Rollers Set High
End View
NOTE: Pop-up Travel Chain Approximately 34" above roller
34 1/2"
18 13/16"
18 13/16"
13 3/4"
1"
17 1/8"
4 1/8"
Standard Bottom
Mount Drive
1"
17 1/8"
34 1/2"
Standard Side Mount Drive
4 1/8"
8"
13 3/4"
POWERED TURNTABLE
Rotation
Optional
Roller Approaches
6"
Dia.
Optional Siderails
Specify Height Required
Expanded Metal Guarding
Four Sides
20" Min.