Concrete Plant Parts Reference Guide Version 2

THIS PAGE
INTENTIONALLY
LEFT BLANK
(IFC)
TABLE OF CONTENTS
AIR SYSTEM........................................................... 4
110 VAC Coil Assemblies – Asco Jucomatic
110 VAC Coil Assemblies – SMC
2 Way Directional Control Valves
4 Way Directional Control Valves
General & Misc Items
ELECTRICAL PARTS.................................................... 39
CB-1 Equipment
Manual Panels – Ross
Miscellaneous
BEARINGS............................................................ 11
LIMIT SWITCHES.......................................................... 45
BELT CONVEYOR................................................ 12
Return Idler Assemblies
Troughing Idler Assemblies
Troughing Idler Assemblies – Individual Rolls
Hardware – Common to Ross Idler Assemblies Radial Conveyors – Ross
LINERS...........................................................................46
BUTTERFLY VALVES........................................... 16
Bray Butterflies
Dynaflow (Virgo) Butterflies
Keystone / Ultraflo Butterflies
Wam Butterflies
Weco Butterflies
MIXERS – ROSS........................................................... 52
Components
Drive Components
Hydraulic Cylinders & Components
Hydraulic Components
Mixer Accessories
CEMENT AERATION............................................ 22
PNEUMATIC & ELECTRICAL VIBRATORS................. 57
CYLINDERS & GATES......................................... 24
Air Cylinders – Johnson Plants
Air Cylinders – Ross Plants
Aggregate Gates – Ross
Blocking Gate (E-Gate)
Plug Valves & Gates – Johnson
SCREW CONEYOR COMPONENTS............................ 58
Boss Exec
Rustler 110, Rustler 160, Rustler II, Rustler R3
Uniplant 100
UniRover U1248
DISCHARGE HEADS – ROSS............................. 30
DISTRIBUTOR REMOTES................................... 33
DUST COLLECTORS............................................ 34
Bag Type Dust Collectors – Johnson
Bag Type Dust Collectors – Ross
V 100 / V 200 / V 400 Parts
V 700 / V 1400 / V 2100 / V 2800
Cartridge Type Dust Collector Parts
Control Parts For 3 & 6 CP Dust Vents
CPV Dust Collector Control Panel
Dust Collectors – C & W
INDICATORS................................................................ 43
MIXER DRUMS...............................................................48
MIXERS – JOHNSON.....................................................50
Hydraulic Power Units
SHROUDS...................................................................... 60
Boots & Clamps
GR Shrouds
Shrouds for:
Bandit B5, Bandit B12
Rustler R3
UniRover U1248
New Style 30” Discharge Head
Standard Old Style 30” Discharge Head
Uniplant & Old Style 24” Discharge Head
WATER SYSTEM............................................................64
ATC Counters
Badger Water Meters
Common Parts For All Badger Meters
Water Strainers
ORDER FORM............................................................... 67
1
IMPORTANT NOTICES
This reference guide for Terex concrete plant parts is not all inclusive for every equipment model
available. Every effort has been made to capture the parts for models still in operation, regardless of
current production status. Images are not scaled to size.
A form is provided at the back of this book if you need additional reference guides. Please send your
request together with your contact information (company name / phone / fax / email), and pertinent
mailing information using any of the following:
Phone:
Fax:
Email:
Mail:
(888) 837-3972
(405) 491-2323
Attn: Parts Literature & Support
[email protected]
Terex Roadbuilding
Attn: Parts Literature / Customer Service
PO Box 1985
Oklahoma City, OK 73101-1985
Important Notes / Acknowledgments:
Manufacturer’s names and products listed in this guide are either registered trademarks “®” or pending trademarks
“TM” and used in a non-trademark manner for explanatory purposes only.
Effective Date: April 2008. Product specifications and prices are subject to change without notice or obligation. The
photographs and/or drawings in this document are for illustrative purposes only. Refer to the appropriate Operator’s
Manual for instructions on the proper use of this equipment. Failure to follow the appropriate Operator’s Manual
when using our equipment or to otherwise act irresponsibly may result in serious injury or death. The only warranty
applicable to our equipment is the standard written warranty applicable to the particular product and sale, and Terex
makes no other warranty, express or implied.
Products and services listed may be trademarks, service marks or trade-names of Terex Corporation and/or its
subsidiaries in the USA and other countries. All rights are reserved. Terex® is a registered trademark of Terex
Corporation in the USA and many other countries.
© 2008 Terex Corporation • All Rights Reserved
No part of this manual may be reproduced in any way without the express prior written consent of Terex Corporation.
2
NOTES:
COMMON ABBREVIATIONS USED IN THIS GUIDE INCLUDE:
TRB # Terex Roadbuilding Part Number
BWD PT#
Brownwood Part Number
CHAMP PT#
Champaign Part Number
I/R
Ingersoll Rand
IMAGES ARE NOT SCALED TO SIZE.
3
AIR SYSTEMS
110 VAC Coil Assemblies - ASCO JUCOMATIC®
DESCRIPTION
TRB #:
ASCO #
BWD PT#:
Two Position, Four-way, Single Solenoid Type
(3/4” body family)
55-76940 54301006
1275000498
Inching, Three Position, ,
Four-way, CLOSED CENTER
Double Solenoid Type
(3/4” body family)
55-77085 54301011
1275000179
Manifold Type Sub-Base (stacking type),
½” NPT ports in end of manifold
Sub-Base End-Plate Kit (for SMC Sub-Bases)
PS001603
PS001604 1275000180
355-00-188
NOTES:
• Rebuild kits for the Jucomatic valves are not available.
• Complete banks of Jucomatic valves can be replaced by complete banks of SMC valves.
• The recommended air system lubricant for ALL Johnson-Ross air systems is Dextron type Automatic
Transmission Fluid (ATF).
4
AIR SYSTEMS
110 VAC Coil Assemblies - SMC
Standard 4-way air control valve on Bandit / Rustler / etc. plants. These valves are mounted in banks on a manifold
type sub base. Two types of valves are used: (a) Two position, single solenoid valves control fill gates and the water
system; and (b) Three position, double solenoid valves are used on the batcher discharge gates to provide “inching”
control.
DESCRIPTION
Two Position, Four-way, Single Solenoid Type
(3/4” body family)
Repair Kit:
Pilot. valve assy: TRB #:
SMC#
BWD PT#:
55-76480 NVFS5110-3DZA
1275001024
PS001424 PS001423 KT-VFS5110
SF4-3FA-30
Inching Three Position, 55-76479 Four-way, CLOSED CENTER,
Double Solenoid Type
(3/4” body family)
Repair Kit: PS001425 Pilot valve assy:
PS001109 NVFR5310-3DZA
Manifold Type Sub-Base (stacking type), ½” NPT
ports in end of manifold
55-76484 MBF5710-04-1
1275601027
Sub-Base End-Plate Kit
(for SMC Sub-Bases)
55-76485 MEF573LR-06-01
1275601026
Three Position, Four-way, 55-76539 OPEN CENTER, Double
Solenoid Type (3/4” body family),
NON-Inching (Used on 1248
swing-chute with transit-mix
discharge option)
1275001025
KT-VFR5300
SF4-3FA-70
VFS5410-3DZA
5
AIR SYSTEMS
2 WAY DIRECTIONAL CONTROL VALVES
110 VAC Coil Assemblies - ASCO
DESCRIPTION
TRB #:
ASCO#
BWD PT#:
3/8” 2-way, pilot operated. Used for aeration and
vibrator actuation
Repair Kit:
Coil:
55-77236 8210G93
1275001008
55-77820
55-77051 302372
238610-032-D
3/4” 2-way, pilot operated Used for aeration and
vibrator actuation
Repair Kit:
Coil: 55-76457 8210G95
55-77821 55-77051 302276
238610-032-D
1 1/4” 2-way, pilot operated. Used for trim water on 1248’s
and similar applications.
Repair Kit:
Coil: 55-47647
8210G8
55-77840 55-77053 302280
238210-032-D
1 1/2” 2-way, pilot operated. Used for aeration actuation in
systems with low pressure-high
volume aerator pumps.
Repair Kit:
Coil: 55-77839 8210G22
55-77822 55-77053 302284
238210-032-D
Pulse-Jet Valve 1”, 2-way, pilot controlled Pulse-Jet valve
for 1, 3, & 6 CP, and , 12, 16, 24, 32,
and 40 CPV Central Dust Collectors
Repair Kit:
Coil: 55-76609 8353G41
55-77823
55-77053 316563
238210-032-D
Four-way, Two Position, Single Solenoid Type
(1/8” body, 1/4” ports, NAMUR
Interface, for water butterfly actuators)
Repair Kit (Spool & seal kit):
Repair Kit (Pilot seal kit):
55-76925 551-00-106
55-77824 55-77825 K-1000-00
978-00-519
6
1275000532
1275001368
1275000392
1275000798
AIR SYSTEMS
4 WAY DIRECTIONAL CONTROL VALVES
110 VAC Coil Assemblies - PARKER / SCHRADER BELLOWS
NOTE: The L705 two position and L695 three position valves are complete stand-alone valve assemblies. The L675
two position and L665 three position valves require a separate sub-base.
DESCRIPTION
TRB #:
P/SB#
Two Position, Four-way, Single Solenoid type with integral sub-base
(1/2” ports) Replaces L645-39-102
Repair Kit:
Shock Pad:
55-47674 L705-49-102-53
55-73067 55-74143 K352 124
K983 002
Inching, Three Position, Four-way, Double Solenoid Type with integral
sub-base (1/2” ports)
Repair Kit:
Shock Pad:
55-77319 L695-49-211-53
55-89747 55-77827 K352 126
K983 004
Two Position, Four-way, Single Solenoid Type with separate sub-base
(3/8” body family)
Repair Kit:
Shock Pad:
55-76767
L675-39-102-53
55-73067 55-74143 K352 124
K983 002
Inching, Three Position, Four-way, Double Solenoid Type with separate
sub-base (3/8” body family)
Repair Kit:
Shock Pad:
55-76933
L665-39-211-53
55-89747 55-77827 K352 126
K983 004
Single Station Sub-Base, 1/2” ports (stand alone, for L665 & L675 series
valves)
55-77320 K022-091
7
AIR SYSTEMS
4 WAY DIRECTIONAL CONTROL VALVES
110 VAC Coil Assemblies - PARKER / SCHRADER BELLOWS
NOTE: The L705 two position and L695 three position valves are complete stand-alone valve assemblies. The L675
two position and L665 three position valves require a separate sub-base.
DESCRIPTION
TRB #:
P/SB#
Manifold Type Sub-Base, 1/2” ports (for L665 & L675 series valves)
55-76768 K142-231
Two Position, Four-way, Single Solenoid Type with integral sub-base (1/4” ports)
Repair Kit:
Shock Pad:
55-47682 L485-29-102-53
55-47677 55-77826 K352 150
K983 001
Two Position, Four-way, Single Solenoid Type with integral sub-base (3/8” ports)
Repair Kit:
Shock Pad:
55-76840
L705-39-102-53
55-73067 55-74143 K352 124
K983 002
Inching, Three Position, Four-way, Double Solenoid Type with integral
sub-base (3/8” ports)
Repair Kit:
Shock Pad:
55-47707
L695-39-211-53
55-89747 55-77827 K352 126
K983 004
8
AIR SYSTEMS
GENERAL & MISCELLANEOUS ITEMS
SMC AIR CONTROL & TUBE FITTINGS
DESCRIPTION
TRB #:
Flow Control, 3/8” MNPT x 3/8” FNPT
55-77049
Flow Control, 1/2” MNPT x 1/2” FNPT
55-77631
Quick Exhaust Assy, 1/2” MNPT x 1/2” Tube
55-77550
Quick Exhaust Assy, 3/8” MNPT x 1/2” Tube
55-77629
Fitting, 1/2” MNPT x 1/2” Tube
55-76470
Fitting, 1/2” MNPT x 3/8” Tube
55-76471
Fitting, 1/4” MNPT x 3/8” Tube
55-76472
Fitting, 3/4” MNPT X 3/4” Tube, 3/4” Ferrule Nut 55-76467
Fitting, 3/8” MNPT x 3/8” Tube
55-77047
Fitting, 3/8” MNPT x 1/2” Tube
55-77048
Fitting, 3/8” MNPT x 3/8” Tube, Aeration L 55-76581
Fitting, 3/8” MNPT x 3/8” Tube, Aeration T 55-76580
Fitting, M4 to 1/4” MNPT (for WAM Butterflies) 55-76616
Tubing, 3/4” Air Brake Tubing
55-76453
Tubing, 3/8” Air Brake Tubing
55-76454
Tubing, 1/2” Air Brake Tubing
55-76455
9
AIR SYSTEMS
GENERAL & MISCELLANEOUS ITEMS
MISCELLANEOUS AIR SYSTEM PARTS
DESCRIPTION
TRB #:
Auto Drain Assy, 1/2” inlet port
55-77876
Dryer 5MC, 3/4 body 77SCFM
55-77148
Gauge, 160 PSI
55-76547
3/4” Regulator 55-76448
3/4” Filter 55-76983
3/4” Filter, Auto Drain for Bowl Assy
55-77870
3/4” Filter, Bowl Assy, metal 55-77872
(sight gauge & auto drain)
3/4” Filter, Element (40 micron)
55-77869
3/4” Filter, Twist Drain for Bowl Assy
55-77871
3/4” Lubricator
55-76984
3/4” Lubricator, Bowl Assy (metal)
55-77873
3/4” Lubricator, Sight Dome & Fill Cap
55-77874
AIR COMPRESSOR PARTS
DESCRIPTION
TRB #:
Intake Filter, for 10 HP I/R Compressor
55-77155
Drive Belt, for 10 HP I/R Compressor
55-PS002281
Tank Gauge, for all I/R Compressors
55-PS002280
Synthetic Oil, for all I/R Compressors
55-77140
10
BEARINGS
GENERAL & MISCELLANEOUS ITEMS
DESCRIPTION
TRB #:
Plug valve bearing 55-12514-10241
4 bolt flange, std duty, 1-1/2”
55-85079
4 bolt flange, std duty, 2”
55-82158
4 bolt flange, std duty, 2-3/16”
55-40067
4 bolt flange, std duty, 2-1/2”
55-82422
4 bolt flange, std duty, 3”
55-89123
2 bolt flange, std duty, 1-1/2”
55-40070
Needle type roller bearing
55-40079
Pillow Block, std duty, 1”
55-40105
Pillow Block, std duty, 1-15/16”
55-40107
Pillow Block, std duty, 2-7/16”
55-71231
Pillow Block, std duty, 2-15/16”
55-71233
Pillow Block, std duty, 2”
55-73883
11
BELT CONVEYOR
RETURN IDLER ASSEMBLIES
Return Idler Assemblies and Impact Idler Assemblies include mounting brackets and pins. Individual rolls come with
bearings mounted; no pins or mounting brackets are included.
DESCRIPTION
TRB #:
CHAMP PT#
BWD PT#:
55-78358 76885
4X24.5RR
55-78359 77013 5740600177
55-78360
17012
0350031400406
55-78361 17013 4X32.34RR
55-78362 76981 0450031400406
55-78363 77093 0550031400406
55-78364
77352 0750031400406
Impact Roll for 24” conveyor, with 5” rubber rollers
55-78424
76942
0170031401745
Impact Roll for 30” conveyor, with 5” rubber rollers
55-78425
77017
0180031401745
Impact Roll for 36” conveyor, with 5” rubber rollers
55-77154
77154
0190031401745
Impact Roll for 48” conveyor,
with 5” rubber rollers
PS000965
17082
0192031401745
5” Rubber Wheel for Impact Roll
55-77168
77168
5740601077
4” x 24 1/2” Roll Flat Idler (load side) for Live Bottom
Batchers with 24” Conveyors
4” x 26 3/4” Roll Return Idler for 24” flat conveyors
on live bottom batchers for 100
Uniplants.
4” x 30 1/2” Roll Return Idler for 24” Ross Inclined
Conveyors & for Flat Idler (load side)
for 30” flat conveyor on live bottom
batchers for 135 Uniplants.
4” x 32 3/4” Roll Return Idler for 30” flat conveyor on
live bottom batchers for 135 Uniplants.
4” x 36 3/4” Roll Return Idler for 30” Ross Conveyors
4” x 42 3/4” Roll Return Idler for 36” Ross Conveyors
4” x 54 3/4” Roll Return Idler for 48” Ross Conveyors
IMPACT ROLL ASSEMBLIES
Used as first return idler, 5” or 6” x 2” Rubber
Rollers on machined tubes, 24 ½” to 54 3/4”
(for 24” to 48” conveyors).
12
BELT CONVEYOR
TROUGHING IDLER ASSEMBLIES
These troughing roller assemblies have pin clips instead of the removable stub shaft. Old style assembly is no longer
available. These troughing idlers match the profile and height of the original Ross troughing idlers.
DESCRIPTION
TRB #:
CHAMP PT#
BWD PT#:
24” x 20° Ross Troughing Idler
55-78357
76930
5740600157
24” x 35° Ross Troughing Idler
55-78356
76888
0150031417744
30” x 20° Ross Troughing Idler
55-77201
77011
5740600674
30” x 35° Ross Troughing Idler
55-77200
76796
0100031417744
36” x 35° Ross Troughing Idler
55-78529
17079
5740601108
48” x 35° Ross Troughing Idler
55-78528
17081
48X35ETRA
13
BELT CONVEYOR
TROUGHING IDLER ASSEMBLIES - INDIVIDUAL ROLLS FOR ROSS
Individual rolls come with bearings mounted; no pins or mounting brackets are included.
DESCRIPTION
TRB #:
CHAMP PT#
BWD PT#:
4” x 8 1/2” Roll Fits Ross 24” - 3 required
Fits Ross 30” - 2 required PLUS 1
14-1/2” roll 4” x 12 1/2” Roll
For Ross 36” equal length NA Replace Idler Assy
76852 0107031417744
NA Replace Idler Assy
77095 4X12.5TR
4” x 14 1/2” Roll
Center Roll for Ross 30”
4” x 16 1/2” Roll Fits Ross 48” x 35° equal length
NA Replace Idler Assy
77014 0106031417744
NA Replace Idler Assy
77124
5740600175
HARDWARE - COMMON TO ALL ROSS IDLER ASSEMBLIES
DESCRIPTION
TRB #:
CHAMP PT#
BWD PT#:
Standard Roll Bearing Used on all Ross Design Rolls (Troughing, Flat, Return,
& Impact)
55-76927
76927 0106300773
Center Mounting Shaft Double-ended shaft used to mount inboard ends of troughing rolls,
and both ends of center rolls.
55-76862
76862 5740600247
End Mounting Shaft Single-ended shaft used to mount outboard ends of troughing rolls, and
all Flat Idlers and Return Idlers.
004002339003 76863 5740600245
77012 0100031401612
Return & Flat Idler Mount “Pillow Block” style 44-314-01612-01
mounting block for flat and return idlers,
accepts End Mounting Shafts above.
Drop Hanger Brackets, 1 1/2”
PS001533
Drop Hanger Brackets, 4 1/2”
55-77363
14
BELT CONVEYOR
RADIAL CONVEYORS - ROSS
DESCRIPTION
TRB #:
Drive Wheel, 12” x 4”, 2-3/16” bore, steel wheel – rubber faced
55-77135
Follower Wheel, 12” x 4”, 1” bore
55-77500
NOTES:
15
BUTTERFLY VALVES
BRAY® BUTTERFLIES
DESCRIPTION
TRB #:
Actuator for 2” & 3” Bray Butterflies
55-77378
Actuator for 4” & 6” Bray Butterflies
55-77379
Namur Interface Kit:
for installing ASCO 551 air control valve
55-76924
4” Butterfly 4” Butterfly Parts, Disc Seal
55-77384
55-77387
3” Butterfly 3” Butterfly Parts, Disc Seal
3” Butterfly Parts, Disc & Stem
55-76926
55-77388
PS001204
2” Butterfly 2” Butterfly Parts, Disc Seal
55-77385
55-77389
2” – 6” Butterfly Parts, Actal Bushing
(for stem on disc)
PS001201
2” – 6” Butterfly Parts, Buna-N stem seal
PS001202
16
BUTTERFLY VALVES
DYNAFLOW (VIRGO) BUTTERFLIES
DESCRIPTION
TRB #:
Actuator for 2” to 6” Dynaflow Butterflies
55-76935 Actuator for 10” Dynaflow
PS001331A
Adaptor (BWD PT# 1275601024) for 2” and 3” Dynaflow using BR80-D8 Actuator
55-77477
Adaptor (BWD PT# 1275601020) for
4” Dynaflow using BR80-D8 Actuator
55-77478
Adaptor sleeve for 10” Butterfly
PS001331B
10” Butterfly
PS001331
4” Butterfly (BWD PT# 3726001018)
55-77371
uses B1 adaptor for BR80-D8 Actuator
3” Butterfly (BWD PT# 3726001741)
uses A1 adaptor for BR80-D8 Actuator
55-76672
3” Butterfly w/ Actuator
55-76761
3” Butterfly Disc Seal Kit
55-77370
2” Butterfly 55-77070
uses A1 adaptor for BR80-D8 Actuator
17
BUTTERFLY VALVES
KEYSTONE / ULTRAFLO BUTTERFLIES
DESCRIPTION
TRB #:
5” Butterfly w/ Actuator PS001064
8” Butterfly ONLY
55-77153
8” Butterfly Assy
55-79004
8” Butterfly with Actuator / no limit switch
55-78950
8” Butterfly Parts, Shaft
PS001252
10” Butterfly
55-87567
10” Wrench Arm
55-74242
Actuator, 10” Butterfly
PS001162
Coil, TRS-150 Actuator PS001161
WECO® BUTTERFLIES
DESCRIPTION
TRB #:
Actuator (Vane type) for 2” to 4” 55-73396
2” Weco Butteryfly (No Actuator) 55-77092
2” Weco Butterfly Seat 55-77443
2” Weco Butterfly Disc 55-77444
3” Weco Butterfly (No Actuator) 55-81892
3” Weco Butterfly Seat
55-81803
3” Weco Butterfly Disc 55-77039
4” Weco Butterfly (No Actuator)
55-80270
18
BUTTERFLY VALVES
WAM® BUTTERFLIES
Nomenclature:
V1FS (size, metric/Std) Single flanged body with beaded extension on output side to receive a shroud, with cast iron disc.
V2FS (size) G - Double Flanged body, cast iron disc.
Size conversions:
100mm = 3.94” = 4” nominal size
150mm = 5.90” = 6” nominal size
200mm = 7.87” = 8” nominal size (8 3/4” boot ID)
250mm = 9.84” = 10” nominal size (10 3/4” boot ID)
300mm = 11.81” = 12” nominal size (12 3/4” boot ID)
350mm = 13.78” = 14” nominal size
400mm = 15.75” = 16” nominal size
The black seal material is superior when using the butterfly for powder applications. The WAM butterflies are for powder
only, they will not hold water.
DESCRIPTION
TRB #:
Thread adapter for all WAM Actuators (5M male to 1/8” MNPT)
55-76616
CP 101 Actuator, for 8” - 12” Butterflies (BWD PT#: 1257501091)
55-73866
CP 125 Actuator, for 14” & 16” Butterflies 55-77814
Adapter - allows use of CP125 actuator on
8” Butterfly
55-78297
M22 Limit Switch, fits all actuators (BWD PT#: 4834100473)
55-73707 Hexagonal Bushing (pivot bushings, 2 required per butterfly,
fits all sizes)
55-73709
Disc seal for 6” WAM Butterfly
PS001049
8” WAM Butterfly, with CP 101 Actuator, and M22 Limit Switch
55-76434
8” WAM Butterfly ONLY (BWD PT#: 3726000471)
55-76974 19
BUTTERFLY VALVES
WAM® BUTTERFLIES
(continuted)
DESCRIPTION
TRB #:
Disc Seal for 8” WAM Butterfly (BWD PT#: 3798200671)
55-77141 Mounting Flange for 8” WAM Butterfly 55-10573-4008-11
10” WAM Single Flange Butterfly ONLY 55-73864
10” WAM Single Flange Butterfly with Actuator & Limit Switch
55-73175
10” WAM Double Flange Butterfly ONLY 55-73865
Disc Seal for 10” WAM Butterfly 55-73708
Mounting Flange for 10” WAM Butterfly (BWD PT#: 0100009902759)
55-10073-1269-01
12” WAM Single Flange Butterfly ONLY 55-77069
12” WAM Double Flange Butterfly ONLY 55-77816
12” WAM Single Flange Butterfly
with Actuator & Limit Switch
55-79214
12” WAM Double Flange Butterfly with Actuator & Limit Switch
55-76435
Disc Seal for 12” WAM Butterfly 55-77809
14” WAM Single Flange Butterfly ONLY 55-77817
20
NOTES:
21
CEMENT AERATION
WAM CEMENT BATCHER AERATORS
DESCRIPTION
Used on Ross plants from approximately
1993 to 2000 TRB #:
55-76987
CONVEYOR COMPONENTS
SILO AERATORS - RECTANGULAR PADS USED ON ROSS PLANTS UNTIL 2000
DESCRIPTION
TRB #:
ADC Aeration Pad with ADK Mounting Kit 55-74850
ADC Aeration Pad without ADK Mounting Kit 55-76902
ADK Mounting Kit
55-77145
Positioning bracket
55-77225
“C” clamp
55-77226
Bin wall gasket (thick)
Aerator gasket (thin)
22
55-77227
55-77228
CEMENT AERATION
JOHNSON-ROSS - PARTS USED ON ALL NEW PLANTS
DESCRIPTION
TRB #:
Silo & Batcher Aerators:
Use 3/8” air brake tubing & 3/8” weld flange,
used on Ross plants after 2000
“L” Type Aerator
55-60268-03521
“T” Type Aerator
55-60268-03511
Diffuser Disc
55-45500
Effective August 1, 2004, diffuser assembly will
have a snap ring to keep disc in place. This
ring will only work with new style body. Old style
diffusers can be replaced with new style.
Snap Ring
55-78901
OLD JOHNSON
SILO AERATORS USED ON JOHNSON PLANTS
DESCRIPTION
TRB #:
Quick Connect - Male with diffuser disc
55-60268-11501
Quick Connect - Male
without diffuser disc
55-10268-11491
Quick Connect - Female
55-35721
Weld Flange, 3/8” FNPT
55-35216
Diffuser Disc
55-45500
23
CYLINDERS & GATES
AIR CYLINDERS – JOHNSON PLANTS
SINGLE STAGE AIR CYLINDERS
DESCRIPTION
TRB #:
3” x 3-1/2” Trunnion Mount w/adjustable bolt
55-60002-20612
3” x 5” Trunnion Mount w/adjustable bolt
55-60002-20616
3” x 8” Trunnion Mount w/adjustable bolt
55-60002-20618
3” x 10-1/2” Trunnion Mount w/adjustable bolt
55-60002-20623
4-1/2” x 5” Trunnion Mount w/adjustable bolt
55-60007-20611
4-1/2” x 8” Trunnion Mount w/adjustable bolt
55-60007-20613
4-1/2” x 10” Trunnion Mount w/o adjustable bolt 55-60007-20617
4-1/2” x 12” Trunnion Mount w/o adjustable bolt 55-60007-20619
4-1/2” x 15” Trunnion Mount w/o adjustable bolt 55-60007-20626
4-1/2” x 16” Trunnion Mount w/o adjustable bolt 55-60007-20627
4-1/2” x 5” Clevis Mount
55-60007-20641
4-1/2” x 8” Clevis Mount
55-60007-20642
6” x 8” Trunnion Mount
55-60010-20843
6” x 8” Clevis Mount
55-60010-20881
24
CYLINDERS & GATES
AIR CYLINDERS – JOHNSON PLANTS
REPAIR KITS and HARDWARE
DESCRIPTION
TRB #:
REPAIR KITS:
3” diameter, Single Stage
55-60002-00481
3” diameter, Two Stage
55-60002-00551
4-1/2” diameter, Single Stage
55-60007-00391
4-1/2” diameter, Two Stage
55-60007-00441
6” diameter, Single Stage
55-60010-00561
8” diameter, Single Stage
55-60010-00661
Bronze Bushing
55-41007
HARDWARE:
Yoke end (4-1/2” cylinders)
55-12525-10411
Yoke pin (4-1/2” cylinders)
55-12508-11203
Yoke end (6” cylinders)
55-12525-10311
Yoke pin (6” cylinders)
55-12508-11646
25
CYLINDERS & GATES
AIR CYLINDERS – ROSS PLANTS
DESCRIPTION
TRB #:
2” x 8” Cylinder (BWD PT# 1251000770)
Rebuild Kit for 2” cylinders
Air Cushion Kit
55-77021
55-77859
55-76891
2 1/2” x 6” Cylinder used on Super 100
55-75967
4” x 8” Cylinder (BWD PT# 1251000238)
Rebuild Kit for 4” Cylinder
Air Cushion kit for 4” cylinders
55-76732
55-76890
55-77466
4” x 10” Cylinder (BWD PT# 1251000980)
55-76889
Parker/Schrader-Bellows Rod Gland kit 55-77044
For Econo Ram II 4” bore cylinders
ENERGY CYLINDERS NO LONGER
AVAILABLE – REPLACE WITH AIR PRO
CYLINDERS AND THE FOLLOWING
MOUNTING MODIFICATIONS
Upper Cylinder Mount for 4” Cylinder Use for conversion from old Energy Cylinders
to NFPA type
55-10573-40062
Lower Cylinder Mount for 4” Cylinder Use for conversion from old Energy Cylinders
to NFPA type
55-10573-40064
26
CYLINDERS & GATES
AGGREGATE GATES - ROSS
DESCRIPTION
TRB #:
CLAMSHELL GATE PARTS
Pivot Bolt, 4 reqd per gate (Old Style) Four (4) required per gate assembly
55-10573-40101
Pivot Bolt (New Style)
001001464000
Pivot Bolt Nut, thin, self-locking (Old Style)
Four (4) required per gate assembly
55-77111
Pivot Bushing, (Old Style)
Four (4) required per gate assembly
55-41015
1/8” Grease Zerk (Old Style)
Four (4) required per gate
55-35200
Cotter Pin (New Style)
000A01536000
Flat Washer (New Style)
000A00301000
Bushing Sleeve Four (4) required per gate
55-10573-4010-07
Garmax® Bearing (New Style)
55-79309
8” Clamshell Gate End Plate Assembly Two (2) required per gate assembly
55-60573-40101
10” Clamshell Gate End Plate Assembly
Two (2) required per gate assembly
55-77287
BLOCKING GATE (E-GATE)
DESCRIPTION
TRB #:
Gate assembely
55-64472-40012
Blocking Plate
55-14472-4001-04
Angle
55-14472-4001-03
1/2” Gum Rubber, 1’-2” long
55-64472-40012-08
27
CYLINDERS & GATES
PLUG VALVES AND GATES – JOHNSON
DESCRIPTION
Old Style Plug Valve:
Cone & Pushrod assembly
Rubber Seal Ring (10” ID)
Shroud Clamp
Canvas Taper Sock
Pin
Operation Lever
TRB #:
55-60061-11742
55-10081-11651
55-60081-10871
55-12545-10111
55-12508-10171
55-62535-12711
12” x 30” Plug Valve: Rubber Wipe (3” x 30”)
Rubber wipe (11/16” x 8-1/8”)
Clamp bar
Plug
Yoke
Yoke Pin
Bearing
Rocker arm
55-60073-01151
12” x 18” Plug Valve 55-60073-02091
28
55-10073-10481
55-10073-10771
55-10073-10891
55-60073-21141
55-12525-10411
55-12508-11203
55-12514-10241
55-10073-10421
CYLINDERS & GATES
PLUG VALVES AND GATES – JOHNSON
DESCRIPTION
Discharge Swing Chute:
Swing chute
Shroud
Shroud clamp
Bearing
TRB #:
55-60548-41451
55-12545-13821
55-35142
55-40070
NOTES:
29
DISCHARGE HEADS - ROSS
TRANSFER CONVEYOR DISCHARGE HEADS
DESCRIPTION
STD 30” TRANSIT MIX DISCHARGE HEAD TRB #:
BWD PT#:
44-308-15185
0100030815185
The main discharge is oval shaped, 24” x 30” (21” x 27” inside dimensions), the water ring
is on the bottom edge, and a 6” pipe passes the cement through the discharge head. This
discharge head typically requires an 8W x 6P x 12” DM shroud to connect the cement
batcher discharge butterfly to the top of the 6” pass-through pipe, then a 6P x 18”
to 36” long GR shroud to carry the cement into the transit mix truck. This discharge
head typically uses an 88” x 18” to 30” long GR shroud to carry the aggregates to the
transit mix truck.
DESCRIPTION
STD 30” TRANSIT MIX DISCHARGE HEAD FOR BANDIT PLANTS
TRB #:
BWD PT#:
55-64144-40401
0100014415097
Main discharge is oval shaped, 24” x 30” (21” x 27” inside dimensions), water ring on bottom
edge, and 6” cement pass-through pipe, same shroud requirements as the Std discharge
head above. THIS DISCHARGE HEAD LOOKS IDENTICAL TO THE STD HEAD ABOVE
BUT HAS A SPECIAL OFFSET TO WORK PROPERLY ON THE BANDIT PLANTS.
DESCRIPTION
STD 24” TRANSIT MIX DISCHARGE HEAD TRB #:
BWD PT#:
308-15372-W3
0100030815372
Main discharge is 24 1/2” OD and 21” ID, round, water ring on bottom edge, and 6” cement pass-through pipe. This
discharge head typically requires an 8W x 6P x 12” DM shroud to connect the cement batcher discharge butterfly to
the top of the 6” pass-through pipe, then a 6P x 18” to 30” long GR shroud to carry the cement into the transit mix
truck. This discharge head typically uses a 77” x 18” to 30” long GR shroud to carry the aggregates to the transit mix
truck.
30
DISCHARGE HEADS - ROSS
TRANSFER CONVEYOR DISCHARGE HEADS
DESCRIPTION
TRB #:
BWD PT#:
55-64308-40011 0100030812953
“OLD STYLE” 30” TRANSIT MIX
DISCHARGE HEAD
The main discharge is round, 21.5” OD, water ring is high inside discharge head and 4” x 4” “V” plate for gum rubber
boot instead of 6” cement pass-through pipe. This type of discharge head will require an 8W x 36” to 48” long GR
shroud for the cement. This boot attaches to the cement batcher discharge butterfly and extends all the way through
the discharge head, into the transit mix truck. This discharge head typically uses an 68” x 18” to 30” long GR shroud
to carry the aggregates to the transit mix truck.
DESCRIPTION
TRB #:
BWD PT#:
DESCRIPTION
TRB #:
BWD PT#:
55-64144-40271 0100014412958
“OLD STYLE” 30” TRANSIT MIX
DISCHARGE HEAD FOR BANDIT PLANTS
The main discharge is 24” diameter, round, water ring is high inside discharge head and 4” x 4” “V” plate for gum rubber
boot instead of 6” cement pipe. This type of discharge head will require an 8W x 36” to 48” long GR shroud for the
cement. This boot attaches to the cement batcher discharge butterfly and extends all the way through the discharge
head, into the transit mix truck. This discharge head typically uses an 68” x 18” to 30” long GR shroud to carry the
aggregates to the transit mix truck.
44-308-12952
0100030812952
“OLD STYLE” 24” TRANSIT MIX
DISCHARGE HEAD
The main discharge is 21” diameter and round, water ring mounted high inside discharge head and 4” x 4” “V” plate
for gum rubber boot instead of 6” cement pipe. This type of discharge head will require an 8W x 36” to 48” long GR
shroud for the cement. This boot attaches to the cement batcher discharge butterfly and extends all the way through
the discharge head, into the transit mix truck. This discharge head typically uses an 68” x 18” to 30” long GR shroud
to carry the aggregates to the transit mix truck.
Cement Pass-thru Pipe
This is a diagram of a new style discharge head. The new style has a pass thru
pipe for the cement where the old style has a V plate trough that allows a rubber
boot for cement to pass thru. The design is the same for 24” and 30” discharge
heads; only the width dimensions will be different. The new style can replace an
old style with some mounting modifications. Must include boots for new style if
using for replacement.
31
DISCHARGE HEADS - ROSS
MISCELLANEOUS PARTS FOR DISCHARGE HEADS
DESCRIPTION
TRB #:
QTY REQ’D
Supporting Angle
55-14144-4082-6r
1
Supporting Angle
55-14144-4082-6l
1
Clamping Bar
55-14144-4082-08
2
Tube Clamp
55-14144-4082-10
2
Cement Tube
55-14144-4082-11
1
Plate
55-14144-4082-17
1
Plate
55-14144-4082-19
1
3/8” x 4” Rubber x 2’ – 8’ Long
55-64144-40401-18
1
Bolt, Hex Head 3/8 –16” UNC x 1 1/4” Long
000-A00058-000
6
Bolt, Hex Head 3/8 –16” UNC x 1 1/2” Long
000-A00059-000
7
Bolt, Hex Head 3/4 –10” UNC x 1 1/2” Long
000-A00165-000
4
Nut, Hex 3/8 –16” UNC
000-A00258-000
13
Nut, Hex 3/4 –10” UNC
000-A00263-000
4
Washer, Flat 3/8””
000-A00294-000
13
32
DISTRIBUTOR REMOTES
TURNHEAD & PIVOT DISTRIBUTOR REMOTES
DESCRIPTION
TRB #:
Garage door type:
Receiver 55-77233
Transmitter 55-77234
Antenna 55-77235
Receiver
4 momentary switches
55-77348
Transmitter
4 momentary rocker switches
55-77349
NOTES:
33
DUST COLLECTORS
BAG TYPE DUST COLLECTORS – JOHNSON
DESCRIPTION
TRB #:
CSJ-125 Bags
4” x 46 3/4”
55-10438-12061
CSJ-250 Bags
4” x 86 3/4”
55-10438-12071
CSJ-1000 / 1500
55-10438-13741
BAG TYPE DUST COLLECTORS – ROSS
DESCRIPTION
TRB #:
CHAMP PT#:
BWD PT#:
Bags, 2’-4 1/2” x 8 1/4”, 8 required
55-76982
Bag Clamps, 29” long, 8 required
Strap Style Clamp, order by inch length needed
($5.03 for band & clamp)
Band Material, 1/2” SS
55-89886
Clamp
55-89887
76982
5722000205
Bags, 3’- 7 1/2” x 8 1/4”, 14 required 55-77359
Bag Clamps, 29” long, 14 required
Strap Style Clamp, order by inch length needed
Band Material, 1/2” SS
55-89886
Clamp
55-89887
77359
5722000342
Blower
55-78191
78191
PB12A
11” x 2 3/4” wheel for 2HP Exhaust Fan (5/8” shaft size)
55-PS002029
Motor, 2HP, 3PH, 60HZ, 230/460V
55-PS002030
Butler DF-4C Dust Collector Parts 55-77018
CA 20 Parts (Cement Batcher Vent, reference
drawing # 522-8090)
Blower (Optional larger blower, reference
drawing # 523-8339)
55-78018
V 100 Parts (Cement Silo Vent, reference
drawing # 500-7889)
34
77018
PB12AW
136-0014
DUST COLLECTORS
BAG TYPE DUST COLLECTORS – ROSS
(continued)
DESCRIPTION
TRB #:
CHAMP PT#:
BWD PT#:
V 200 Parts
Bags, 7’-1” x 8 1/4”, 14 required (recommended for Cement)
55-76860
76860
5722000192
76918
722000341
78191
PB12A
Bags, 7’-1” x 8 1/4”, 14 required 55-76918 (recommended for Flyash)
Bag Clamps, 29” long, 14 required
Strap Style Clamp, order by inch length needed
Band Material, 1/2” SS
55-89886
Clamp
55-89887
Exhaust Fan, 2 HP 55-78191
11” x 2 3/4” wheel for 2HP Exhaust Fan (5/8” shaft size)
V 400 Parts
Bags, 7’-1” x 8 1/4”, 28 required
(recommended for Cement)
55-PS002029
PB12AW
55-76860 76860
5722000192
Bags, 7’-1” x 8 1/4”, 28 required
55-76918
(recommended for Flyash)
Bag Clamps, 29” long, 28 required
Strap Style Clamp, order by inch length needed
($5.03 for band & clamp)
Band Material, 1/2” SS
55-89886
Clamp
55-89887
76918
5722000341
Exhaust Fan, 3 HP
55-78192
78192
PB123HP
13” x 3.2” wheel for 3HP Exhaust Fan (5/8” shaft size)
Vibrator
V 700, V 1400, V 2100, V 2800
Bags, 8-1/4” X 9’-4 1/2” (112 1/2”) Number of bags required:
V 700...................36
V 1400.................72
V 2100...............108
V 2800...............144
55-PS002287
5510302
55-87574
87574
55-78081
136-0014
35
DUST COLLECTORS
CARTRIDGE TYPE DUST COLLECTOR PARTS
DESCRIPTION
TRB #:
CHAMP PT#:
BWD PT#:
55-76219
76219
5722000193
Poly Media Cartridge, 8 3/8” x 12 3/4” x 26” 55-76399
cartridge, for 12, 16, 24, 32, and 40 CPV
Central Dust Collectors (BWD PT # Ref # CDV)
76399
5722000496 Either the Paper or Poly Media Cartridge can
be used in any of the dust collectors. The poly
media is slightly finer, and is washable.
Paper Media Cartridge, 8 3/8” x 12 3/4” x 26” cartridge, for 3CP, 6CP, and 1CP
(BWD PT # Ref # DV)
Cartridge Hanger, “V” Rod Welded onto plenum 44-530-15250-19
plate, for 3 & 6 CP, and 12, 16, 24, 32, and
40 CPV Central Dust Collectors
0119053015250
Cartridge Hanger, Threaded Rod Hooks onto 44-530-15250-20
77037
“V” Rod, for 3 & 6 CP, and 12, 16, 24, 32, and
40 CPV Central Dust Collectors
Cartridge Holder Plate Assembly Round plate, 55-77063
77063
with gasket. Supports the bottom cartridge,
held by the threaded rod, for 3 & 6 CP, and
12, 16, 24, 32, and 40 CPV Central Dust
Collectors
Holder Plate Gasket Closed-cell foam gasket, 44-GASKET DVF
12” OD X 8” ID x 3/8” thick, for 3 & 6 CP, and
12, 16, 24, 32, and 40 CPV Central Dust
Collectors
0120053015250
Holder Plate Nut with handle, holds round plate 55-77038
up, for 3 & 6 CP, and 12, 16, 24, 32, and
40 CPV Central Dust Collectors. Also used to
hold door closed.
91043A031
Pulse-Jet Valve 1”, 2-way, pilot controlled
Pulse-Jet valve for Dust Collectors
0121053015250
GASKET DVF
55-76609
76609
1275000392
Door Gasket: 3/8” x 1” Closed cell foam gasket 55-77636
material
77636
1108701007
36
DUST COLLECTORS
CARTRIDGE TYPE DUST COLLECTOR PARTS
(continued)
DESCRIPTION
TRB #:
CHAMP PT#:
BWD PT#:
6CP Air Manifold 6” round (new style)
44-530-15250-W14
17003
0150053015250
4CP Air Manifold
55-64525-40016
6CP Mating Flange
44-500-14119-A1
1-1/4” Rod, Air valve attachment
44-530-15250-16
Coupling, 3/4” NPT x 5”, Cut in half
44-530-15250-15
Pipe Coupling, 3/4” x 5” NPT Pipe Coupling
002009504005
CONTROL PARTS FOR 3 & 6 CP DUST VENTS
DESCRIPTION
TRB #:
CHAMP PT#:
BWD PT#:
Differential Pressure Switch
44-4833000715
77025
4833000715
Pulse-Jet Controller 55-77004
77004
4650900262
Repeat Cycle Timer Circuit Assembly Timer
55-76989
76989
4274000204
5 Meg plug-in Pot for Timer (controls “off” time 55-77473
between cleaning cycles)
77473
5013900717
Finder Relay
55-76990
76990
4814900723
Socket for Finder Relay
55-77709
77709
4819900691
J-Box Assembly
55-60600-26581
37
DUST COLLECTORS
CPV DUST COLLECTOR CONTROL PANEL
DESCRIPTION
TRB #:
BWD PT#:
White Lens (Round)
55-78074
4317501403
Red Lens (Round)
55-77507
4317901405
Green Lens (Round)
55-77563
4317901401
Amber Lens (Round)
55-77183
4317901400
Lamp Base
55-77185
4317901405
120 VAC Lamp
55-77073
4317501685
C & W DUST COLLECTORS
DESCRIPTION
TRB #:
Paper Media Cartridge, 8” x 19” cartridge for CP-35
PS001408
Paper Media Cartridge, 8” x 39” cartridge for CP-1000, CP-1200
PS001502
Paper Media Cartridge, 8” x 54” cartridge for CP-1000
Door Rubber Trim, rubber trim for CP style collectors
Electrical Timer, 360-120-1 sec timer for CP collectors 55-76217
PS001359
55-PS000933
Solenoid Valve, 3/4” Solenoid valve for CP-35 PS001210
collector
Double Bulkhead, 1” Bulkhead for Solenoid PS001361
valve
Auger Motor, 1 HP electric motor for CP-1000 PS001398
auger
Vane Feeder Motor, 1/2 HP, 71 frame, 230/460, PS001412
1720 RPM, electric motor for vane feeder on
CP-1000
Vane Feeder Packing CP-1000
38
PS002000
ELECTRICAL PARTS
COMMON ELECTRICAL PARTS
EQUIPMENT FOR ADDITION OF CB-1
DESCRIPTION
TRB #:
CB-1 EPROM, w/ English, metered water and 55-79375
no moisture probe
CB-1 EPROM, w/ English, metered water and
moisture probe
55-79376
CB-1 EPROM, w/ Spanish, metered water and 55-79377
no moisture probe
CB-1 EPROM, w/ Spanish, metered water and 55-79378
moisture probe
Printer, CB-1
55-76235
KVA Battery back-up
55-77659
Line Quench Arc Suppression board
44-0100020217
IQ-510 read out, DWI
55-76387
Lithium Battery for IQ and 510
PS002223
AC Output fuse
PS001317
CB-1 Firmware
PS001780
CB-1 Board
PS001870
Controller i Card
PS001167
Ribbon Cable
55-PS002311
Power Supply Kit
55-PS002172
39
ELECTRICAL PARTS
COMMON ELECTRICAL PARTS
MANUAL PANELS - ROSS
DESCRIPTION
BATCHER DISCHARGE SWITCHES
Batcher discharge switch, two momentary contact pushbuttons
Batcher discharge switch, Contactor NO
Batcher discharge switch, Cover
ON/OFF SWITCHES
Run/Off, 2 position rotary
Run/Off, Rotary contactor set, NO
TRB #:
55-77553
55-76313
55-77554
55-76948
55-76315
START/STOP STATIONS, ROTARY SWITCHES
Start/Stop station, 3 position rotary, maintain
55-78078
LEFT, Momentary Right
Start/Stop station, rotary contactor set, NO/NC 55-77376
FILL GATE SWITCHES
Square pushbutton, momentary contact
Contactor set, NO
55-77000
55-76315
ADMIX FILL SWITCHES
Square pushbutton, momentary contact
Contactor set, NO
55-77000
55-76315
ADMIX DISCHARGE SWITCH
Square pushbutton, latching
Contactor set, NO
55-77633
55-77634
COMBINATION ADMIX FILL / DISCHARGE
SWITCHES, ROTARY TYPE
3 position rotary, maintain RIGHT
Rotary contactor set, NO/NO
55-78078
55-78077
40
ELECTRICAL PARTS
COMMON ELECTRICAL PARTS
MANUAL PANELS - ROSS - continued
DESCRIPTION
TRB #:
INDICATOR LAMP PARTS
Indicator light bulb
Indicator light socket
55-77073
55-77505
Indicator light lens, AMBER
Indicator light lens, BLUE
Indicator light lens, RED
Indicator light lens, GREEN
Indicator light lens, CLEAR
Indicator light lens, WHITE
Indicator light lens, YELLOW
55-77183
55-77506
55-77507
55-77563
55-78073
55-78074
55-78075
KEY SWITCH
Control, key switch
Key switch, contactor set, NO
55-77722
55-76949
EMERGENCY STOP SWITCH
E-stop switch
E-stop switch, contactor set, NO
55-78076
55-77504
WATER CONTROL SWITCHES
Water Stop & Reset Switch:
Square pushbutton momentary contact 55-77000
Water Start & Reset switch, contactor set NO
55-76315
Water Select & Hold switch:
Three position rotary
55-77293
Water Select & Hold, NC-NC contactor set
55-77504
Water Select & Hold, NO-NO contactor set
55-78077
41
ELECTRICAL PARTS
COMMON ELECTRICAL PARTS
MISCELLANEOUS
DESCRIPTION
TRB #:
Line Starter - Non-Rev, Size 2, 120V
55-74844
Line Starter - Non-Rev, Size 3, 120V
55-74945
Relay Overload, Size 4, 144AMP
55-74946
Standard Motor Starter - Heater Pack
55-74940
Contactor - Non-Rev, 5 CH, 120V
55-74943
Timer (Midtex)
55-77190
Lamp, 120V
003002119000
Switch, 3 position maintained
003002602008
Switch, 2 position maintained
003002602001
Switch, 2 position key
003002602007
Fuse, 2A
55-43772
Fuse Block
55-43770
Finder Relay
55-76990
Base Socket for Finder Relay 55-72393
Strobe Light Bulb
PS001556
Strobe Light 55-74214
42
INDICATORS
BIN INDICATORS
DESCRIPTION
TRB #:
ROTO-BIN-DICATOR® (UniRover U1248)
Model R, Type 7 (115,1/60hz)
55-45234
3’ Extension (Bindicator model)
55-10223-1322-01
Paddle (3 Vane)
55-83450
Cord Grip
55-44255
Roll Pin
55-45223
Pipe
10223-1322-01
1/8 Half Coupling
002009504001
MONITOR®
Model KA (115,1/60)
55-76950
3’ Extension
55-PS000962
Paddle (3 Vane)
55-76756
Mounting Plate
55-78007
43
INDICATORS
BIN INDICATORS
DESCRIPTION
TRB #:
MONITOR ROTO SIGN
(Rustler R3 & Bandits)
®
Roto Sign (115,1/60)
55-76755
Coupling, Screwed
55-35433
Banana Paddle
55-76757
Flex Coupling
55-78006
Pipe
55-64144-4119-04
Pipe Coupling
55-35429
MOISTURE PROBES
Digital Microwave Moisture Sensor
55-76813
READOUT
55-76814
Slump Meter UPC
55-76922
Liquid Level Probe 55-78616
Circuit Board 55-78617
8” FLOAT ASSEMBLY
Level Switch
55-60223-13711
Coupling
002-009511-016
Pipe
002-009501-083
Ball, Float
55-76518
44
55-76519
LIMIT SWITCHES
LIMIT SWITCHES
DESCRIPTION
TRB #:
Limit switch, short travel
55-43172
Limit switch, magnetic
55-73424
Roller arm
55-73425
Proximity switch
55-76545
Safety limit switch, conveyor
307000061000
45
LINERS
JOHNSON 12 YD3 DRUM POLY LINERS
DESCRIPTION
Drum Liner Kit
includes items #1 - #13:
Front Cone Liner #1
Front Cone Liner #2
Girth Liner #3
Girth Liner #4
Rear Cone Liner #5
Rear Cone Liner #6
Back Cone Liner #7
Reinforcing Collar Liner #8
Spindle Cap Edge Liner #9 Spindle Cap Edge Liner #10
Spindle Ring Liner #11
Spindle Cap Liner #12
Blade Face Liner #13 46
TRB #:
QTY:
55-60566-44921
55-10566-44921
55-10566-44922
55-10566-44923
55-10566-44924
55-10566-44925
55-10566-44926
55-10566-44927
55-10566-44928
55-10566-44929
55-10566-449210
55-10566-449211
55-10566-449212
55-10566-449213
4
4
4
4
4
4
8
4
1
1
1
1
4
LINERS
ROSS MIXER POLY LINERS
FOR: 8, 10, 12 YD3 ROSS TILT MIXERS
DESCRIPTION
TRB #:
QTY:
12 YD Liner Kit
44-407-19320-A1
includes:
Nose Cone Liner
44-407-19320-01
12 YD Belly Band Liner 44-407-19320-02
Rear Cone Liner
44-407-19320-03
Hub Cone Liner 44-407-19320-04
Hub Cover Liner 44-407-19320-05
Hub Cap Liner (round) 44-407-19320-06
8
8
8
8
1
1
Sikaflex Adhesive
Rubber Seal for Discharge Hood
55-79257
36
Rubber Only
55-14309-4007-01
Seal Ring for 1” Poly Liners
44-404-16257
8 YD Belly Band Liner 10 YD Belly Band Liner
55-77804
8
8 YD Blade Liner
10 YD Blade Liner
12 YD Blade Liner Kit
includes 4 each of:
Face Liner
Tip Liner
Tip Liner
55-77805
4
55-77342
4
44-407-18979-A1
1
55-78577
55-78578
55-78579
4
4
4
55-64309-40071
55-77341
8
Cone and Chute Liners
(see diagram at right):
Spill chute polyliner #1 55-79088
Spill chute polyliner #3 55-79090
Spill cone polyliner #4 55-78520
Spill chute polyliner #2 55-79089
47
MIXER DRUMS
JOHNSON MIXER DRUMS
DESCRIPTION
TRB #:
Johnson Style Concrete Plant Mixer Drum (Ring Gear included)
55-60566-44663
Forged Ring Gear for Johnson Style Drum
55-10451-42393
ROSS MIXER DRUMS
DESCRIPTION
TRB #:
Ross Style Concrete Plant Mixer Drum (Ring Gear included)
44-406-19166-A1
Ring Gear for Ross Style Drum 44-404-12613
48
NOTES:
49
MIXERS - JOHNSON
JOHNSON MIXER HYDRAULIC POWER UNIT
DESCRIPTION
TRB #:
4OHP HYDRAULIC POWER UNIT
55-76651
Complete Directional Valve
Coil Pilot Valve
Flow Control
Body Valve (serial # req’d)
Cartridge
Flow Control
55-PS002109
55-76586
55-PS001385
55-76095
CALL FOR PN
PS002124
55-PS002123
Bolt Kit
55-78295
Sun Dump Valve**
Solenoid & Coil
Coil Only
55-78329
PS000984
PS000985
Vane Pump
55-77060
Return Filter
Filter Head Assy
55-77061
55-PS002344
Proportional Valve**
Coil
55-78330
PS001909
** For Variable Speed Units Only
50
DESCRIPTION
TRB #:
Self Erect Valve
Emergency Tilt Valve
Handle (Lever) Assy
Handle (Lever) Only
55-78294
PS001797
PS001885
PS001886
Suction Strainer
Relief Valve
Amplifier Card**
Dump Control Valve
1/2 Coupling
Coupling insert
1/2 Coupling
Clean Out Gasket
Top Gasket
Motor, 40HP, 1800RPM, 230/460/60/3
Motor, 2HP, 1800RPM, 115/230/60/1
Pressure Gauge (0-3000 PSI)
Secondary Pump, gear
Sight Level & Temperature Gauge
320008060000
55-77062
55-77446
55-77983
PS001242
PS001244
PS001245
PS001753
PS001752
CALL FOR PN
PS001916
55-76760
55-77977
PS001656
MIXERS - JOHNSON
51
MIXERS - ROSS
ROSS MIXER COMPONENTS
PADDLES & BOLTS
DESCRIPTION
TRB #:
CHAMP PT#:
BWD PT#:
10 YD3 (7.64 M3) PADDLES & LEGS 55-64404-40011 64404-40011 Includes complete bolt kit (noted below)
and 12 support legs total:
Four paddles: 3 legs per paddle55-14404-4001-W1
-front support, 4 required
55-14404-4001-W2
-middle support, 4 required 55-14404-4001-W3 -rear support, 4 required
55-14404-4001-W4 01000040402243
64404-40012 0150040402243
64406 40021
01000040605689
64406-40022
0150040605689
PADDLES ONLY 55-14404-4001-W1 12 YD3 (9.1 M3) PADDLES & LEGS 44-406-05689-A1 Includes complete bolt kit (noted below)
and 12 support legs total:
Four paddles: 3 legs per paddle44-406-05689-W1
-front support, 4 required
44-406-05689-W2
-middle support, 4 required 44-406-05689-W3
-rear support, 4 required
44-406-05689-W4
PADDLES ONLY (SINGLE) 44-406-05689-W1
0150040402243
0160040402243
0170040402243
0180040402243
BOLT KIT
(same for 10 YD3 & 12 YD3 mixers)
Includes 32 (thirty-two) 3/4” x 2 ½”
grade 5 bolts with nuts and lock
washers; and 48 (forty-eight) 1” x 4”
grade 5 bolts with nuts and lock
washers.
QTY
32
ITEM
3/4” x 2 1/2” grade 5 bolts
000A00169000
32
3/4” nuts 000A03494000
32
3/4” flat washers 000A00299000
32
3/4” lock washers 000A00311000
48
1” x 4” grade 5 bolts 000A00213000
48
1” nuts 000A00277000
48
1” flat washers 000A00301000
48
1” lock washers 000A00313000
52
MIXERS - ROSS
ROSS MIXER COMPONENTS
BEARINGS & SEALS
DESCRIPTION
TRB #:
Front Bearing, Cone (Nose Cone End) 55-77419
Front Bearing, Cup (Nose Cone End) 55-77418
Rear Bearing, Cone
55-77420
Rear Bearing, Cup 55-77421
Wear Ring For Rear Seal
55-77413
Rear Seal, Single Piece NOT split 55-78194
Rear Seal, Split Seal, Can be installed in the field.
55-77329
Glue (Rear Split Seal)
Must use with Split Seal.
One tube should be sufficient for one
split seal.
55-79113
53
MIXERS - ROSS
DRIVE COMPONENTS
DESCRIPTION
TRB #:
3
12 YD MIXER 60 HP
Motor, 60 HP, 1800 TEFC, 364T Frame
316000520550
Gear Reducer, Modified for tilting applications
55-78433
Gear Breather DCR6
55-78434
Gear Scoop, G-Grid Line & Scoop
GEARS & MISCELLANEOUS
18 Tooth Pinion Gear Ring Gear (Bull Gear) NOTE* 12 week lead time if
not in stock
55-78435
55-77172
44-404-12613
INSTALLATION TOOL and CLAMPS
REQUIRED for FIELD INSTALLATION
(No charge if returned)
Ring Gear Installation Tool 44-407-19144-A1
Ring Gear Clamps (requires qty 10)
54
44-407-19145-A1
MIXERS - ROSS
HYDRAULIC CYLINDERS & COMPONENTS
FOR: 8, 10, 12 YD3 ROSS TILT MIXERS
DESCRIPTION
TRB #:
BWD PT#:
Tilt Cylinder 4” x 48” with 2- 3/4” rod 55-77096
12510000953
Rod End with spherical bearing for 4” x 48” Tilt Cylinder
44-406-15640-10
0110040615640
Spherical Bearing (Rod End) 55-78466
Rod End Cylinder Pin for 4” x 48” Tilt Cylinder
Clevis Mount (lower cylinder mount) for 4” x 48” Tilt Cylinder
44-404-04316-W2
0119040404316
44-406-15640-A2
0130040615640
Spherical Bearing (Clevis Mount) 55-78465
Lower Cylinder Pin for 4” x 48” Tilt Cylinder
55-78215
Main Pivot Pin 4” OD x 8 1/2” Long 44-404-04316-W1 Main Pivot Pin Bushing Receiver 44-404-03128-A1
WITH Bushing Installed
NOTE: This item is sold as one unit
only and consists of TRB part
44-404-03128-008 sleeve, and
44-404-03128-09 bronze bushing.
Neither can be sold separately.
0118040404316
0108040403128 &
0109040403128
55
MIXERS - ROSS
HYDRAULIC COMPONENTS
DESCRIPTION
TRB #:
HYDRAULIC POWER UNITS
40 HP (Paving operations) 15 HP (Ready Mix) 55-78521
55-78540
PVG HYDRAULIC VALVES
PVG 120 Valve
– 40 HP Hydraulic Units
– Valve Coil, 24 VDC
PS001415
55-78068
PVG 12 Handle & Seal Kit
PS001413
PVG 32 Valve (SERIAL # REQUIRED) CALL FOR
– 15 HP Hydraulic Units PART NUMBER
– Valve Coil, 24 VDC
PVG 32 Handle & Seal Kit
PS001328
MISC. COMPONENTS
Filter (Return) for 40 HP PS001333
Hydraulic Units
Ramp Generator
55-76647
Seal Kit (pv15 pump)
55-78122
MIXER ACCESSORIES
DESCRIPTION
TRB #:
Gob Hopper
44-407-17001
Discharge Cone & Chute
44-406-10043-W1
Telescoping Discharge Shroud (12” Travel)
44-407-16952-PS
Telescoping Discharge Shroud (18” Travel)
44-407-15072-PS
Telescoping Shroud Assy
44-407-19155-A1
Telescoping Shroud with Wringer
44-407-19157-A1
Wringer Gate - Standard
44-407-19156-A1
Swing-away Drip Pan
44-407-18742-A1
Swing-away Drip Pan Assy
44-407-19263-A1
Splash Guard
44-406-12729
56
PNEUMATIC & ELECTRIC VIBRATORS
PNEUMATIC & ELECTRIC VIBRATORS
DESCRIPTION
TRB #:
Cleveland #3/4 SAEP
55-45400
Cleveland #1 SAEP
55-45401
WAM S36P
(replacement for the BG-35)
55-76733
1-1/4 #1125 VMS with mounting plate
55-45402
Piston type 1-1/4”
55-76739
2” #1200 VMS with mounting plate
55-77139
3” Piston type
55-79006
Electric BGSF 36 / 100, 110 / 1 / 60
55-74208
Electric MVE0300-36U, 230 / 460 / 30 / 60
55-74210
Ball 1”
55-77066
57
SCREW CONVEYOR COMPONENTS
SCREW CONVEYOR COMPONENTS
DESCRIPTION
RUSTLER 110
Head flight for fill screw (6” dia x 119” lg)
TRB #:
55-78676
Tail flight for fill screw (6” dia x 117” lg)
55-78675
Discharge screw for batcher (6” dia x 41” lg)
55-78677
RUSTLER 160
Standard Head flight for fill screw
55-78633
Standard Tail flight for fill screw
55-78272
Tail section assembly
44-126-19082-A1
Discharge screw for batcher
(6” dia x 92” lg)
55-78679
RUSTLER II
Head flight for fill screw
(9” dia x 86” lg)
Tail flight for fill screw
(9” dia x 87” lg)
RUSTLER R3
Hardware:
Wood bearing, 2”:
Hanger w/ bearing
Head shaft spacer
BOSS EXEC
Head flight for silo screw
(9” dia x 144-3/8” lg)
Tail flight for silo screw
(9” dia x 190-1/2” lg)
Hardware:
Coupling shaft field install kit
58
55-79160
55-79159
55-40018
55-76741
55-60573-40161-39
55-79302
55-79303
44-362-325-A1
SCREW CONVEYOR COMPONENTS
SCREW CONVEYOR COMPONENTS
DESCRIPTION
UNIPLANT 100
Discharge screw for batcher
(6” dia x 69: lg)
Hardware:
Tail shaft, 1-1/2: x 9-1/2”
Coupling shaft, 1-1/2” x 11-1/2”
Bearing hanger, 1-1/2”
Hard iron bearing, 1-1/2”
Connecting bolts, 1-1/2” shaft
Head shaft, 1-1/2” x 12-1/2”
Seal plate, 1-1/2”
UNIROVER U1248
Conversion Kit - move reducer from tail to head, Cement side
TRB #:
55-78338
55-77009
55-76936
55-77317
55-77008
55-78635
55-76946
55-77104
55-60455-40981
Conversion Kit - move reducer from
tail to head, Fly ash side
55-60455-40982
Conversion Kit - Reducer adapter, Cement side
55-60455-40961
Conversion Kit - Reducer adapter, Fly ash side
55-60455-40962
Hardware:
Wood bearing, 3”
Hanger w/ bearing
C5 adjustable adapter
C4 adjustable adapter
55-81405
55-81900
55-78474
55-78475
59
SHROUDS
SHROUD CLAMPS
DESCRIPTION
TRB #:
CHAMP PT#
BWD PT#
Cable Clamp for 6” Pipe
55-64472-40026
64472-40026
5710501343
Cable Clamp for 8” WAM
55-64472-40027 64472-40027
5710501259
Cable Clamp for 10” WAM 55-64472-40023 64472-40023 5710501258
Cable Clamp for 12” Pipe 55-64472-40022 64472-40022
5710501349
Strap Style Clamp, order by the inch
length required. Band Material, 1/2”
SS
Clamp
55-89886
55-89887
BATCHER DISCHARGE DM SHROUDS
DESCRIPTION
TRB #:
BWD PT#:
8P x 6P x 8”
Standard on BANDIT, BTR and
BTRR plants
55-12545-14691 472-14874-1A
10P x 8P x 8”
55-12545-14661
472-14874-2A
12P x 10P x 8”
55-12545-15271
472-14874-3A
14P x 10P x 8”
55-12545-14861
472-14874-4A
8W x 6P x 10”
55-12545-14781
5710001306
8W x 6P x 12”
55-12545-14641
5710001305
8W x 8P x 8”
55-12545-14621
5710001310
8W x 10P x 10”
55-12545-14771
5710001312
8P x 10P x 12”
55-12545-14581
5710001316
10W x 10P x 12”
55-12545-14822
5710100083
10W x 12P x 10”
55-12545-14631
5710001321
10W x 12P x 12”
55-12545-14871
5710001322
12P x 14P x 12”
55-12545-14861
5710001324
60
SHROUDS
GR SHROUDS
CEMENT PASS-THROUGH GR SHROUDS
DESCRIPTION
TRB #:
CHAMP PT#
BWD PT#
8” WAM to Truck, 36” long, GR 55-12545-14701 12545-14701
8” WAM to Truck, 48” long, GR 55-12545-15085
12545-15085
5710101473
8” WAM to Truck, 60” long, GR
55-12545-15086
12545-15086
5710101813
6” Pipe to Truck, 24” long, GR Cement boot for standard new style
discharge head.
55-12545-14655
12545-14655
6” Pipe to Truck, 30” long, GR Cement boot for standard new style
discharge head.
55-12545-14653 12545-14653
6” Pipe to Truck, 36” long, GR Cement boot for standard new style
discharge head.
55-12545-14651 12545-14651 5710000771 (22X36GR)
6” Pipe to Truck, 48” long, GR Cement boot for standard new style
discharge head.
55-12545-14652
12545-14652
(22X48GR)
SHROUDS, BOOTS & CLAMPS
DM = GR = RR = Diaphragm Material. Vinyl coated canvass material, black on one side, gray on the other side.
Used on Ross Plants for shroud material.
Gum Rubber. Used as a discharge shroud on Ross transit mix plants. Standard thickness is 1/8”.
Red Rubber. Used as a gasket material on powder butterfly and piping connections. Also used to seal low
pressure water piping connections. Typical thickness is 1/8”.
61
SHROUDS
GR SHROUDS
FOR DISCHARGE HEADS
DESCRIPTION
TRB #:
30” NEW STYLE DISCHARGE HEAD
88” x 18” Water Ring to Truck, 55-12545-14611
18” long, GR; Agg boot for standard
new style 30” discharge head.
CHAMP PT#
BWD PT#
12545-14611
5710100769 (88X18GR)
88” x 24” Water Ring to Truck, 24” long, GR; Agg boot for standard
new style 30” discharge head.
55-12545-14612
12545-14612 88X24GR
88” x 30” Water Ring to Truck, 30” long, GR; Agg boot for standard
new style 30” discharge head.
55-12545-14763
77167 5710101475
88” x 36” Water Ring to Truck, 36” long, GR
55-12545-14614
12545-14614
5710000787
UNIPLANT & OLD-STYLE 24”
DISCHARGE HEAD
65” x 18”
55-12545-14552
12545-14552 5710000237 (65X18GR)
65” x 24” 55-12545-14551
76947
5710000130
65” x 26” 55-12545-14555
65” x 28” 55-12545-14556
65” x 30” 55-12545-14553
12545-14553
65X30GR
STANDARD OLD-STYLE
DISCHARGE HEAD
68”x18” Water Ring to Truck, 18” long, GR
55-12545-14922
68”x24” Water Ring to Truck, 24” long, GR
67-1/2” act cir, 21-1/2 act ID
55-12545-14921
68”x30” Water Ring to Truck, 30” long, GR
67-1/2”act cir, 30-1/2 act ID
55-12545-14923
68”x36” Water Ring to Truck, 36” long, GR
67-1/7” act cir, 30-1/2 act ID
55-12545-14924
62
SHROUDS
GR & DM SHROUDS
FOR PLANTS
DESCRIPTION
TRB #:
BANDIT B5
Discharge Head
Aggregate Shroud GR
Cement ShroudGR
55-12545-14722
55-12545-14651
Cement Wt. Bin
10” x 10” Cement Fill DM
Cement Discharge DM
55-12545-14631
55-12545-14591
BANDIT B12
Discharge Head
29” x 18” Aggregate Shroud GR
7” x 18” Cement Shroud GR
55-12545-14492
55-12545-14491
Cement Weigh Bin
8”W x 10”P x 8”Cement Fill DM
Cement Discharge DM
55-12545-14661
55-12545-14641
RUSTLER R3
Discharge Head
Aggregate Shroud GR
Cement Shroud GR
55-79410
55-79411
Cement Weigh Bin
Cement Fill DM
Cement Discharge DM
55-12545-14471
55-12545-14481
UNIROVER U1248
Cement Chute GR
Plug Valve DM
55-12545-15151
55-12545-10951
MISCELLANEOUS
78” x 30”
20” x 24”
55-77161
55-12545-11161
63
WATER SYSTEMS
BADGER® WATER METERS
DESCRIPTION
4” Meter, Complete / Flange Mount
4” Meter, Head Assembly, Complete (includes
impeller housing assembly and transmitter head
assembly, 4 Pole Impeller and Buna Seals)
TRB #:
55-73126
55-75934
4” Meter, Head Gasket 55-45256
4” Meter, Rotor & Spindle (Impeller)
55-76869
4” Meter, PFT-4E Transmitter Head Assy, Complete
55-71782
(includes circuit board, housing and Magneto-Resistive
pickup). Fits 4” meters only.
4” Meter, Lower Housing Assembly for PFT-4E
55-77832
Transmitter board. Magneto-Resistive sensor ONLY
is included (no circuit board, no upper cover, screws, or
gaskets). Fits 2” and 3” meters.
4” Meter, Tetra seal 55-88487
3” Meter, Complete / Flange Mount 55-89782
3” Meter, Rotor & Spindle (Impeller) 55-71699
3” Meter, Head Assembly, Complete (includes Impeller 55-74230
housing assembly, Impeller, and 2-transmitter head
assembly). Fits 2” and 3” meters.
2” Meter, Complete / Flange Mount 55-72872
2” Meter, Meter, Rotor & Spindle (Impeller)
55-76886
2” Meter, Head Assembly, Complete (includes Impeller 55-76928
housing assembly, Impeller, and transmitter head
assembly). Fits 2” and 3” meters.
1-1/2” Meter with Transmitter
64
55-74168
WATER SYSTEMS
COMMON PARTS FOR ALL BADGER® METERS
DESCRIPTION
TRB #:
PFT-4E Transmitter Cover, Clear Plastic PFT-4E Transmitter Cover, Gasket 55-77058
PFT-4E Transmitter (Board Only) 55-72787
55-77059
2” & 3” Meter, PFT-4E Transmitter Assembly, 55-77077
Complete (includes circuit board, housing and
Magneto-Restive pickup). Fits 2” and 3” meters.
2” & 3” Meter, Lower Housing Assembly for 55-77831
PFT-4E Transmitter board. Magneto-Resistive
sensor ONLY is included (no circuit board, upper
cover, screws, or gaskets). Fits 2” and 3” meters.
2” & 3” Meter, Head Gasket 55-89782/24
2” 3” Meter, Viton Gasket
PS001025
2” & 3” Meter, Tetra Seal 55-85974
WATER STRAINERS
4” Strainer, Complete / Flange Mount Screen
3” Strainer, Complete / Flange Mount Screen
2” Strainer, Complete / Flange Mount Screen
55-46532
55-PS002273
4” Strainer, Complete / Threaded Ends
Screen
3” Strainer, Complete / Threaded Ends
Screen
2” Strainer, Complete / Threaded Ends
Screen
55-PS002276
55-PS002277
55-46529
55-PS002274
55-77373
55-PS002275
55-PS002278
PS001100
44-3960100344
55-PS002279
65
WATER SYSTEMS
ATC COUNTERS
DESCRIPTION
ATC 366, Water Controller (Simi Automatic)
TRB #:
55-88533
ATC 376, Water Controller (Simi Automatic,
55-77160
scalable, and solid state) *Used on current
manual panels.
NOTES:
66
ORDER FORM
REFERENCE GUIDE ORDER FORM
Fax this Completed Order Form to:
405-491-2323 Attn: Parts Literature & Support
OR Mail to:
TEREX ROADBUILDING
ATTN: PARTS LITERATURE / CUSTOMER SERVICE
PO BOX 1985
OKLAHOMA CITY, OK 73101-1985
PLEASE PRINT CLEARLY
Your Name_____________________________________________________
Title________________________________ Quantity Requested _________
Company Name_________________________________________________
Company Address _______________________________________________
City _______________________ St ______ Zip _______ Country________
Phone (
) _________________
FAX (
) _____________________
Please allow 3 - 4 weeks for shipping. There is no charge for these reference guides.
TEREX ROADBUILDING • PO BOX 1985 • OKLAHOMA CITY, OK 73101-1985
[email protected] • www.terexrb.com • (888) 837-3972
67
NOTES:
68
THIS PAGE
INTENTIONALLY
LEFT BLANK
(IBC)
TEREX ROADBUILDING
•
PO BOX 1985
•
OKLAHOMA CITY, OK 73101
CUSTOMER SERVICE AND SUPPORT
Call (888) 837-3972 • Fax (405) 491-2323 • Email: [email protected] • www.terexrb.com
© 2008 Terex Corporation • All Rights Reserved
Terex® is a registered trademark of Terex Corporation in the United States of America and many other countries. Products and services listed may be
trademarks, service marks, or trade names of Terex Corporation and/or its subsidiaries in the United States of America and other countries, and rights
are reserved.