installation - Craftmatic Parts

Transcription

installation - Craftmatic Parts
INSTALLATION
·'
d. Position channel connector so that
the flat side is flush against bed base
frame. Attach channel connector to
bed base frame using (2) 1//2 inch
long hex head bolts/nuts (FIGURE
18). Tighten bolts. Note: For beds
with 74" base length, use inner
mounting holes. For beds with 80"
base length, use outer mounting
holes (FIGURES 16 and 18).
USE (2}3 INCH LONG CARRIAGE
BOLTS'TO ATTACH BRACKET
CHANNEL TO BED BASE FRAME
ADJUSTABLE
BED TYPE A
FIGURE 19: Bed base Type A bracket channel attachment.
AD,IUSTABLE
BE[ITYPE B
FIGURE 18: Bed base Type B channel connector attachment.
e. Using (2) 3 inch long carriage bolts/
nuts, attach (1) headboard bracket
channel to bed base frame (bed base
TypeA) (FIGURE 19) or (1) channel
connector (bed base Type B) (FIGURE
20). Hand tighten bolts/nuts (loosely)
to allow adjustment of the headboard
bracket channels.
f. Attach (1) headboard bracket flange
to one of the bracket channels with
(2) 1 inch long hex head bolts/nuts
(FIGURES 21 and 22). Tighten bolts.
g. Repeat procedure to attach the other
headboard bracket.
FIGURE20: Bed base Type B bracket channel attachment.
~c'l-~~
S\.\O~:0~C;
\~o~
• ,"' I>-S~~fO-I>-C~\~
L??7 (jJ1~s"'O"
~
~
C>
g
'"
'"::::I
ro
c:
::.:E
'"
~
'"
~
UJ
(J)
USE (2}'1INCH LONG HEX HEAD
BOLTS TO ATTACH BRACKET ' "'.
fLANGE TO BRACkET cHANNEL
FIGURE 21: Bed base Type A headboard bracket flange
attachment.
q:
<D
~
e
13e
INSTALLATION
12. Install headboard brackets to the
bed base frame per the following
instructions:
Note: Headboard brackets are optional for
Type B beds. See accessory sheet for order
information.
a. Raise the head section of the bed
(with hand control) to gain access to
the bed base frame.
b. Determine bed base type (FIGURES
14 and 15). For bed base Type A,
proceed to Step "e". For bed base
Type B, proceed to Step "c".
c. For bed base Type B, locate channel
connector kit (FIGURE 16). On one
side of bed base frame, locate
(2) holes for channel connector
mounting (FIGURE 17).
80" BASE
LENGTH
MOUNTING
HOLES
FIGURE 16: Channel connector
B. See accessory sheet).
kit. (Used with bed base Tvp«
FIGURE 17: Channel
mounting
ADJUSTABLE
BED TYPE A
FIGURE 14: Bed base Type A.
ADJUSTABLE
BED TYPE B
~~
(0
r-
<>
,:>
,'>
en
,0
co
",=
'0
::E
~~
(0
c:
~;
U.
V)
<r
a:i
Q;
;;:
d:
12e
FIGURE 15: Bed base Type B.
connector
holes.
I
INSTALLATION
h. When installing a headboard,
footboard, or four-piece surround
(case good), allow for 7.5 inches
(38.1mm) to 2 inches (50.8mm) of
clearance at the head and foot of the
bed and a minimum of 1/2 inch to 3/4
inch on the sides (FIGURE 22).
I. Firmly tighten the 3 inch carriage
bolts of both headboard bracket
channels.
/- Measure the distance (center-tocenter) between the mounting holes
in the headboard.
k. Measure the center-to-center
distance between the mounting slots
of the headboard bracket flanges
(FIGURE 23).
I. If bracket flange adjustment is
required to accept the headboard,
remove the
7 inch long hex
head bolts adn
move flanges
side-to-side for
the adjustment
(FIGURE 23).
; •••
Reinstall bolts.
Tighten all
headboard
mounting bolts.
m. Install
headboard.
USE (211 INCH LONG HEX HE.
BOLTS TO ATTACH HEA-DBOAJ
B.RACKET FLANGE TO BRACKI
CHANNEL
FIGURE 22: Bed base Type B headboard
attachment.
bracket flange
MEASURE FLANGE SLOTS
CENTER-TO-CENTER TO CHECK
HEADBOARD HOLE LOCATION
:
• :
.;;
~
I
I
I
12. Install mattress on
the adjustable bed
base.
~
00
r-.
o
o
M
en
en
ro::>
c
'"
:2
e
c
'"
~
Typical Power Foundation
installation is now complete.
If bed is equipped with
programmable settings or
options, refer to the Hand
Control Guide for programming
information.
REMOVE 1 INCH LONG HEX HEAD BOLTS AND RELOCATE
FLANGES TO ACI-JIEVE.'CE~R~TO"'CENTER·bISTANCE
REQUIRED FOR HEADSC)'ARDMOUNTlNG"HOLES
FIGURE 23: Headboard
headboard.
bracket
.
1.1'1.0
measurement
and adjustment
to accept
:fj: NOTE
w
(/)
ri!i
~
~
I
I
TWIN SIZE HEADBOARD BRACKET ASSEMBLIES ARE
SHOWN (FIGURES 22 AND 23). QUEEN SIZE HEADBOARD
RDl\rll'C'T~ Ace rru
IIftftr""""
••••.••••.•
a._.
-
-_
.• ---
INSTALLATION
Note: It is important to position the
bottom of the headboard cross member
a maximum distance of 3 inches
(76.2mm) between the headboard and
the top of the mattress (FIGURE 13). Do
not exceed 3 inches (76.2mm).
FIGURE 12: Mattress retainer installed.
,
Note: if bed is to be set up without
a headboard, basic installation is
now complete. If headboard is to be
installed, proceed to Headboard Bracket
Installation.
~
11. Install headboard brackets to the bed
base frame*. When attaching {2} twin
size units to a king size headboard an
optional swing hinge kit {see accessory
section} may be used to connect the twin
units.
FIGURE 13: Headboard cross member location must not
exceed 3 inches (76.2mm) from the top of the mattress.
* S-cape
™ and Optima are Type A bed
base frames. Silhouette
and
Pro-Motion ™ are Type B bed base
frames.
TM,
'V~NOTE
FAILURE TO FOLLOW HEADBOARD BRACKET
INSTAl.LA)10N INSmUCTIONS MAY CAUSE
HEADBOARD BRACKET INTERFEaENCE WITH
BASE FOAM DURING POWER FOUNDATION
OPERATION. BASE FOAM OR BASE COVER
DAMAGE COULD RESU.LT.
~
fe
~
~::J
.,
c:
~
~
Q)
c:
;:
o
!
w
<J)
~
~