Eaton® Char-Lynn® Disc Valve Hydraulic Motors

Transcription

Eaton®
Char-Lynn®
Disc Valve Hydraulic Motors
Disc Valve:
2,000, 4,000 Compact, Delta,
4,000, 6,000, 10,000 Series
C-1
State of the art motors benefiting from
45 years of experience and innovating
constantly to fit your demands.
C-2
C-3
C-4
C-5
C-6
EATON Low Speed High Torque Motors E-MOLO-MC001-E6 September 2011
C-i
Disc Valve Hydraulic Motors
Highlights
Product Description
In the late 1950’s the original low speed, high torque
hydraulic motor was developed from a pump Geroter
element consisting of an internal gear ring and a
mating gear or star. While attaching the internal
gear ring to the housing as a non moving part, oil
was ported to pressurize and turn the internal star
in an orbit around a center point. This slow turning
star coupled with a splined drive to the output shaft
became the Char-Lynn Orbit® motor.
A few years after this original Char-Lynn Orbit motor
was introduced another original motor concept went
into production. This motor had rolls incorporated into
the internal gear ring, this element was identified by
the name Geroler and is a registered trade name of
Eaton Hydraulics. From these early years the Geroler
motor has seen many design changes to make these
Geroler motors the best the industry has to offer.
Examine the simplicity of these Geroler disc valve
motors shown below. Also examine all the following
pages for high value Char-Lynn disc valve motors
from Eaton Hydraulics.
Port B
Port A
Geroler ® Star
D isc Valve
Motor Shaft Drive
and Valve Driv e
Motor Shaft
and Bearings
C-ii
EATON Low Speed High Torque E-MOLO-MC001-E6 September 2011
Features, Benefits, and Applications
Features
Char-Lynn Hydraulic motors
provide design flexibility.
All disc valve motors are
available with various configurations consisting of:
• Displacement
(Geroler size)
Benefits
Applications
• Lowest pressure drop
motor in the industry
• Swing motor
• Widest range of options
• Harvesting equipment
• The most experienced
manufacturer of LSHT
motors
• Brush Cutters & mowers
• Directional boring
• Turf equipment
• Skid Steer loaders
• Output Shaft
• Fairway mowers
• No Shaft and Bearing
Assembly (Bearingless
Motor)
• Harvesters
• Mowing
• Port Configuration
• Snow removal
• Mounting Flange
• Sprayers
• Other Special Features
• Trencher
• Wood products
C-1
• Grinders and mixers
• Forestry equipment
• Irrigation reels
C-2
C-3
C-4
Standard Motor
The standard motor
mounting flange is located
as close to the output shaft
as possible. This type of
mounting supports the
motor close to the shaft
load. This mounting flange is
also compatible with many
standard gear boxes.
Wheel Motor
The wheel motor mounting
flange is located near the
center of the motor which
permits part or all of the
motor to be located inside
the wheel or roller hub. In
traction drive applications,
loads can be positioned
over the motor bearings for
best bearing life. This wheel
motor mounting flange
provides design flexibility in
many applications.
Bearingless Motor
C-5
The bearingless motor has
the same drive components
as the standard and wheel
motors (with the exception
that the motor is assembled C-6
without the output shaft,
bearings and bearing
housing). The bearingless
motor is especially suited
for applications such as gear
boxes, winch drives, reel
and roll drives. Bearingless
motor applications must
be designed with a bearing
supported internal spline
to mate with the bearingless motor drive. Product
designs using these
hydraulic motors provide
considerable cost savings.
C-iii
Table of Contents
HighlightsC-ii
Features, Benefits and Applications
C-iii
Table of Contents
C-iv
2000 Series
HighlightsC-1-1
SpecificationsC-1-2
Performance Data
C-1-3
DimensionsC-1-8
Installation Information
C-1-14
Shaft Side Load Capacity
C-1-18
Case Pressure and Case Porting
C-1-19
Product Numbers C-1-23
Model Code
C-1-24
2000 Series Two-Speed
DescriptionC-1-25
Performance Data
C-1-25
Typical Hydraulic Circuit
C-1-26
SpecificationsC-1-27
DimensionsC-1-28
Product Numbers
C-1-30
4000 Compact Series
Highlights C-2-1
SpecificationsC-2-2
Performance Data
C-2-3
Dimensions
C-2-9
C-2-12
C-2-17
Case Pressure and Case Port
C-2-18
Model Code
C-2-22
Delta Series
Highlights
Specifications
Performance Data
Dimensions
Installation Inforamtion
Model Code
C-iv
4000 Series
HighlightsC-4-1
SpecificationsC-4-2
Performance Data
C-4-3
DimensionsC-4-8
C-4-11
C-4-13
C-4-14
Product Numbers
C-4-16
Model Code
C-4-17
6000 Series
HighlightsC-5-1
SpecificationsC-5-2
Performance Data
C-5-3
DimensionsC-5-8
C-5-12
C-5-14
C-5-15
Dimensions Ports
C-5-16
Product Numbers
C-5-17
Model Code
C-5-18
10,000 Series
HighlightsC-6-1
SpecificationsC-6-2
Performance Data
C-6-3
DimensionsC-6-5
C-6-8
Side Shaft Load Capacity
C-6-10
Product Numbers
C-6-12
Model Code
C-6-13
C-3-1
C-3-2
C-3-3
C-3-9
C-3-10
C-3-11
EATON Low Speed High Torque E-MOLO-MC001-E6 September 2011
2000 Series
Features
• Three zone design for
longer life and true
bi-directionality.
Highlights
Port B
• Bearings that meet the
highest standards of the
industry
Port A
• Options to optimize
performance in every
application
Geroler ® Star
• Integrated cross-over
relief valve option
Benefits
• Easy to design in a
system
D isc Valve
Motor Shaft Drive
and Valve Driv e
Motor Shaft
and Bearings
• Compact design of the
integrated cross-over
relief valve option
Applications
Description
The popular 2000 Series provides torque up to 7500 lb-in.
This proven design is reliable and durable. Eaton has added
options that make the motor more flexible to use in a wide
variety of applications. The integral cross-over relief valve is
the latest innovation in the 2000 series motors.
• Skid Steer Attachments
• Swing Motor
• Brush Cutters & Mowers
• Harvesting Equipment
• Directional Boring any
place pressure relief
protection is optimal for
system or motor performance and life
• Turf equipment
2000 Series
Geroler Element
Flow l/min [GPM]
Speed RPM
Pressure bar [PSI]
Torque Nm [lb-in]
• Reliablity and performance
in tough application
10 Displacements
75 [20] Continuous**
115 [30] Intermittent*
908 Cont.**
1042 Inter.*
200 [3000] Cont.**
300 [4500] Inter.*
845 [7470] Cont.**
930 [8225] Inter.*
** Continuous— (Cont.) Continuous rating, motor may be run continuously at these ratings.
* Intermittent— (Inter.) Intermittent operation, 10% of every minute.
Auger
Boring
Plastic Injection
Oil and Gas Equipment
C-1-1
C-1
2000 Series
Specifications
Specification Data — 2000 Series Motors
Displ. cm3/r [in3/r]
80 [4.9]
90 [5.5]
100 [6.2] 130 [8.0] 160 [9.6] 195 [11.9] 245 [14.9] 305 [18.7] 395 [24.0] 490 [29.8]
Max. Speed
Continuous
908 836 742 576477 385308246191153
(RPM) Intermittent
908 1042924 720713 577462365287230
@ Flow
Flow
Continuous 75 [20]
75 [20]
75 [20]
75 [20]
75 [20]
75 [20]
75 [20]
75 [20]
75 [20]
75 [20]
l/min [GPM] Intermittent 75 [20]
95 [25]
95 [25]
95 [25]
115 [30] 115 [30] 115 [30] 115 [30] 115 [30] 115 [30]
Torque*
Continuous 235 [2065] 265 [2326] 295 [2630] 385 [3420] 455 [4040] 540 [4780] 660 [5850] 765 [6750] 775 [6840] 845 [7470]
Nm [lb-in] Intermittent 345 [3035] 390 [3458] 445 [3950] 560 [4970] 570 [5040] 665 [5890] 820 [7250] 885 [7820] 925 [8170] 930 [8225]
Pressure Continuous205 [3000] 205 [3000] 205 [3000] 205 [3000] 205 [3000] 205 [3000] 205 [3000] 205 [3000] 155 [2250] 120 [1750]
∆ bar
Intermittent 310 [4500] 310 [4500] 310 [4500] 310 [4500] 260 [3750] 260 [3750] 260 [3750] 240 [3500] 170 [2750] 140 [2000]
[∆ PSI]
Peak
310 [4500] 310 [4500] 310 [4500] 310 [4500] 310 [4500] 310 [4500] 310 [4500] 310 [4500] 205 [3250] 170 [2500]
Weight
Standard or 9.3 [20.5] 9.3 [20.5] 9.5 [21.0] 9.8 [21.5] 10.0 [22.0] 10.4 [23.0] 10.9 [24.0] 11.3 [25.0] 11.8 [26.0] 12.2 [27.0]
kg [lb]
Wheel Mount
Bearingless 7.3 [16.0] 7.3 [16.0] 7.5 [16.5] 7.7 [17.0] 7.9 [17.5] 8.4 [18.5] 8.8 [18.5] 9.3 [20.5] 9.8 [21.5] 10.2 [22.5]
Maximum Case Pressure: See case pressure seal limitation graph.
*See shaft torque ratings for limitations.
Note:
To assure best motor life,
run motor for approximately
one hour at 30% of rated
pressure before application
to full load. Be sure motor is
filled with fluid prior to any
load applications.
Maximum Inlet Pressure:
310 bar [4500 PSI]
Do not exceed ∆ pressure
rating (see chart above).
∆ bar [∆ PSI] :
The true pressure difference
between inlet port and
outlet port
Maximum Return Pressure:
310 bar [4500 PSI] with case
drain line installed.
Continuous Rating:
Motor may be run continuously at these ratings
Intermittent Operation:
10% of every minute
Peak Operation:
1% of every minute
C-1-2
Recommended Fluids:
Premium quality, anti-wear
type hydraulic oil with a
viscosity of not less than 70
SUS at operating temperature.
Recommended System
Operating Temp.:
-34°C to 82°C [-30°F to
180°F]
Recommended Filtration:
per ISO Cleanliness Code,
4406: 20/18/13
2000 Series
80 cm3/r [4.9 in3/r]
∆Pressure Bar [PSI]
[500]
35
[1000]
70
[1500]
105
[2000]
140
[2500]
170
[3000]
205
[3500]
240
68
[210]
25
3
[250]
30
17
[330]
35
44
[330]
35
90
[325]
35
182
[320]
35
273
[310]
35
365
[300]
35
456
[285]
30
547
[270]
30
638
[255]
30
729
[230]
25
818
[420]
45
1
[500]
50
8
[670]
75
40
[670]
75
85
[670]
75
176
[665]
75
267
[660]
75
375
[650]
75
448
[640]
70
537
[625]
70
629
[610]
70
720
[590]
65
810
[740]
85
3
[990]
110
37
[995]
110
81
[1005]
115
170
[1010]
115
259
[1015]
115
349
[1010]
115
439
[1005]
115
530
[990]
110
622
[975]
110
714
[955]
110
795
[1300]
145
34
[1310]
150
78
[1330]
150
166
[1340]
150
254
[1345]
150
341
[1350]
155
429
[1350]
155
516
[1340]
150
603
[1330]
150
689
[1310]
150
775
[1550]
175
28
[1580]
180
72
[1620]
185
159
[1655]
185
246
[1685]
190
333
[1700]
190
420
[1705]
195
507
[1705]
195
593
[1690]
190
679
[1680]
190
765
[1800]
205
22
[1840]
210
65
[1920]
215
152
[1975]
225
238
[2020]
230
325
[2050]
230
411
[2065]
235
497
[2065]
235
584
[2055]
230
670
[2025]
230
756
[1950]
220
14
[2100]
235
57
[2200]
250
140
[2270]
255
223
[2330]
265
306
[2370]
270
388
[2390]
270
470
[2395]
270
553
[2385]
270
635
[2355]
265
717
[2110]
240
2
[2365]
265
49
[2480]
280
128
[2570]
290
207
[2640]
300
286
[2690]
305
364
[2715]
305
442
[2720]
305
521
[2700]
305
599
[2660]
300
677
[2630]
295
42
[2765]
310
117
[2880]
325
192
[2960]
335
266
[3010]
340
341
[3035]
345
415
[3030]
340
490
[2995]
340
564
[2935]
330
638
[20
]
76
[210]
25
908
[570]
65
901
[930]
105
880
[1290]
145
861
[1645]
185
851
[1985]
225
842
[2305]
260
799
[2600]
295
755
[2845]
320
712
Performance Data
[.25]
,95
[.5]
Motors run with high
efficiency in all areas
designated with a number
for torque and speed. For
best motor life select a
motor to run with a torque
and speed range shown in
the light shaded area.
Performance data is typical
at 120 SUS. Actual data may
vary slightly from unit to unit
in production.
1,9
[1]
Flow LPM [GPM]
3,8
[2]
7,5
[4]
15
[6]
23
[8]
30
[10 ]
38
[12 ]
Continuous
Peak
Intermittent
No Operation
45
[14 ]
53
[16 ]
61
[18 ]
[570]
65
901
90 cm3/r [5.5 in3/r]
[250]
15
[.25]
,95
[.5]
1,9
[1]
3,8
[2]
7,5
[4]
15
[6]
Flow LPM [GPM]
23
[8]
30
[10 ]
38
[12 ]
45
[14 ]
53
[16 ]
61
[18 ]
68
[20]
76
[22]
83
[24]
91
[25]
95
[500]
35
[1000]
70
[1500]
105
[2000]
140
[2500]
170
[3000]
205
[3500]
240
[4000]
275
[124]
14
5
[133]
15
15
[151]
17
39
[151]
17
82
[151]
17
167
[142]
16
250
[133]
15
35
[124]
14
418
[106]
12
502
[98]
11
585
[233]
26
2
[273]
31
13
[358]
40
39
[358]
40
80
[350]
40
163
[348]
39
245
[338]
38
328
[331]
37
410
[315]
36
493
[298]
34
575
[471]
53
1
[555]
63
6
[744]
84
35
[744]
84
76
[899]
102
158
[736]
83
240
[729]
82
329
[724]
82
404
[714]
81
485
[706]
80
567
[832]
94
2
[1091]
123
32
[1099]
124
72
[1113]
126
152
[613]
69
233
[1128]
127
314
[1130]
128
395
[1127]
127
477
[1115]
126
559
[1424]
161
28
[1439]
163
68
[1473]
166
148
[1492]
169
227
[1509]
170
306
[1521]
172
385
[1525]
172
464
[1525]
172
543
[1697]
192
21
[1737]
196
61
[1800]
203
139
[1851]
209
218
[1890]
214
295
[1912]
216
373
[1924]
217
451
[1924]
217
529
[1952]
221
13
[2015]
228
50
[2132]
241
126
[2208]
249
203
[2269]
256
281
[2309]
261
361
[2326]
263
441
[2326]
263
521
[2189]
247
12
[2293]
259
38
[2454]
277
115
[2552]
288
191
[2635]
298
266
[2670]
302
342
[2704]
306
417
[2707]
306
493
[2368]
268
2
[2570]
290
29
[2775]
314
102
[2898]
327
176
[3000]
339
249
[3036]
343
322
[3082]
348
394
[3080]
348
467
[80]
9
670
[62]
7
753
[53]
6
836
[35]
4
920
[18]
2
1003
[285]
32
658
[262]
30
740
[242]
27
822
[231]
26
916
[204]
23
1000
[195]
22
1042
[688]
78
650
[673]
76
732
[644]
73
814
[639]
72
907
[612]
69
991
[594]
67
1033
[1107]
125
641
[1087]
123
719
[1045]
118
796
[1047]
118
895
[1011]
114
978
[994]
112
1020
[1510]
171
622
[1490]
168
701
[1447]
163
780
[1437]
162
876
[1366]
154
960
[1384]
156
1003
[1907]
215
607
[1892]
214
685
[1850]
209
765
[1836]
207
854
[1792]
202
940
[1765]
199
984
[2311]
261
610
[2281]
258
680
[2246]
254
748
[2218]
251
749
[2182]
247
918
[2173]
246
954
[2697]
305
568
[2662]
301
643
[2617]
296
719
[2599]
294
803
[2573]
291
882
[2564]
290
921
[3070]
347
541
[3030]
342
613
[2988]
338
686
[2981]
337
774
[2963]
335
850
[4000]
275
[4500]
310
}
Torque [lb-in ]
Nm
Speed RPM
[4500]
310
[2855]
323
20
[3100]
350
90
[3249]
367
161
[3367]
380
231
[3398]
384
302
[3458]
391
372
[3450]
390
431
[3432]
388
513
[3381]
382
583
[3301]
373
653
C-1-3
C-1
2000 Series
100 c3m/r [6.3/2r ]in
Performance Data
[.25]
in production.
,95
[.5]
1,9
[1]
3,8
[2]
7,5
[4]
15
[6]
23
[8]
Flow LPM [GPM]
30
[10 ]
Continuous
Peak
Intermittent
No Operation
38
[12 ]
45
[14 ]
53
[16 ]
61
[18 ]
68
[20]
76
[22]
83
[24]
91
[25]
130 c3m/r [8.3/0r ]in
[250]
15
[.25]
,95
[.5]
1,9
[1]
3,8
[2]
7,5
[4]
15
[6]
Flow LPM [GPM]
23
[8]
30
[10]
38
[12]
45
[14]
53
[16]
61
[18]
68
[20]
76
[22]
83
[24]
91
[25]
95
C-1-4
[170]
20
3
[190]
20
12
[230]
25
28
[230]
25
56
[220]
25
114
[220]
25
172
[200]
25
230
[180]
20
287
[160]
20
345
[150]
15
403
[130]
15
461
[110]
10
518
[90]
10
576
[60]
5
634
[40]
5
692
[20]
1,0
720
[500]
35
[1000]
70
[1500]
105
[2000]
140
[2500]
170
[3000]
205
[3500]
240
[4000]
275
[4500]
310
[250]
15
[500]
35
[1000]
70
[1500]
105
[2000]
140
[2500]
170
[3000]
205
[3500]
240
[4000]
275
[4500]
310
[140]
15
4
[150]
15
13
[170]
20
35
[170]
20
73
[170]
20
148
[160]
20
222
[150]
15
297
[140]
15
371
[120]
15
445
[110]
10
519
[90]
10
594
[70]
10
668
[60]
5
742
[40]
5
816
[20]
1,0
890
[260]
30
2
[300]
35
9
[390]
45
34
[390]
45
71
[380]
45
145
[380]
45
219
[370]
40
294
[368]
40
367
[350]
40
442
[330]
35
516
[320]
35
591
[300]
35
665
[280]
30
739
[260]
30
813
[230]
230
887
[220]
25
924
[620]
70
5
[830]
95
31
[830]
95
68
[820]
90
141
[820]
90
215
[810]
90
288
[810]
90
362
[800]
90
436
[800]
90
509
[780]
90
583
[770]
85
657
[730]
80
731
[720]
80
805
[690]
80
879
[670]
75
916
[940]
105
2
[1210]
135
28
[1220]
140
63
[1240]
140
136
[1260]
140
209
[1260]
140
281
[1270]
145
354
[1270]
145
427
[1260]
140
500
[1260]
140
573
[1240]
140
646
[1180]
135
715
[1180]
135
794
[1140]
130
868
[1120]
125
905
[1570]
175
23
[1590]
180
59
[1640]
185
131
[1670]
190
202
[1700]
190
273
[1720]
195
344
[1730]
195
415
[1740]
195
486
[1720]
195
558
[1700]
190
630
[1630]
185
703
[1620]
185
777
[1540]
175
852
[1560]
175
890
[1870]
210
15
[1920]
215
51
[2010]
225
121
[2080]
235
192
[2130]
240
261
[2160]
245
330
[2180]
245
399
[2180]
245
469
[2160]
245
540
[2140]
240
611
[2090]
235
684
[2070]
235
758
[2020]
230
834
[1990]
225
873
[2130]
240
6
[2220]
250
38
[2380]
270
104
[2480]
280
172
[2560]
290
243
[2610]
295
316
[2630]
295
389
[2630]
295
463
[2610]
295
537
[2580]
290
609
[2550]
290
662
[2500]
280
749
[2460]
280
814
[2450]
275
846
[2520]
285
24
[2750]
310
94
[2880]
325
163
[2990]
340
231
[3020]
340
300
[3070]
345
369
[3070]
345
437
[3060]
345
506
[3020]
340
574
[2980]
335
643
[2930]
330
712
[2900]
330
782
[2890]
325
817
[2810]
315
14
[3120]
355
80
[3280]
370
149
[3420]
385
216
[3440]
390
283
[3510]
395
350
[3500]
395
417
[3500]
395
485
[3460]
390
552
[3440]
390
619
[3360]
380
687
3340]
375
754
[3120]
355
4
[3490]
395
69
[3680]
415
134
[3840]
435
200
[3850]
435
266
[3950]
445
332
[3940]
445
378
[3940]
445
463
[3900]
440
529
[3830]
435
595
95
[1560]
175
89 0
[410]
45
8
[510]
60
27
[510]
60
56
[500]
55
113
[490]
55
171
[480]
55
224
[470]
55
286
[460]
50
344
[440]
50
402
[420]
45
460
[400]
45
517
[380]
45
575
[350]
40
633
[325]
35
691
[310]
35
719
[870]
100
2
[1070]
120
23
[1080]
120
53
[1080]
120
111
[1080]
120
169
[1080]
120
222
[1070]
120
282
[1060]
120
338
[1030]
115
395
[1010]
115
452
[990]
110
509
[960]
110
568
[940]
105
624
[920]
105
682
[900]
100
712
[1580]
180
19
[1600]
180
47
[1620]
185
104
[1640]
185
161
[1650]
185
219
[1650]
185
276
[1640]
185
333
[1620]
185
391
[1600]
180
447
[1580]
180
504
[1550]
175
560
[1520]
170
619
[1490]
170
676
[1480]
165
705
[2050]
230
16
[2090]
235
42
[2150]
245
97
[2190]
245
153
[2220]
250
210
[2230]
250
269
[2230]
250
327
[2220]
250
385
[2200]
250
443
[2160]
245
500
[2130]
240
551
[2100]
235
604
[2070]
235
665
[2050]
230
692
[2520]
285
13
[2580]
290
39
[2660]
300
95
[2740]
310
149
[2780]
315
204
[2800]
315
261
[2800]
315
317
[3000]
340
373
[2780]
315
430
[2750]
310
484
[2710]
305
539
[2680]
305
597
[2650]
300
651
[2630]
295
679
[2920]
3309
9
[2930]
330
36
[3100]
350
92
[3260]
370
146
[3310]
375
201
[3420]
385
255
[3350]
380
307
[3350]
380
360
[3330]
375
411
[3300]
375
471
[3280]
370
524
[3250]
365
579
[3220]
365
633
[3200]
360
682
[3310]
375
3
[3320]
375
28
[3540]
400
85
[3770]
425
132
[3840]
435
192
[3940]
445
243
[3910]
440
295
[3910]
440
348
[3890]
440
397
[3860]
435
456
[3840]
435
508
[3820]
430
560
[3780]
425
616
[3700]
420
656
[3640]
410
21
[3980]
450
77
[4280]
485
118
[4360]
495
184
[4450]
505
231
[4440]
500
284
[4440]
500
336
[4440]
500
384
[4410]
500
440
[3990]
450
13
[4420]
500
70
[4800]
540
104
[4890]
550
175
[4970]
560
219
[4960]
560
272
}
Torque [lb-in ]
Nm
Speed RPM
2000 Series
160 c3m/r [9.3/6r ]in
[250]
15
Performance Data
[.25]
in production.
,95
[.5]
1,9
[1]
3,8
[2]
7.5
[4]
15
[6]
Flow LPM [GPM]
23
[8]
Continuous
Peak
Intermittent
No Operation
30
[10]
38
[12]
45
[14]
53
[16]
61
[18]
68
[20]
195 c3m/r [11.3/9r ]in
[.25]
,95
[.5]
1,9
[1]
3,8
[2]
7,5
[4]
15
[6]
Flow LPM [GPM]
23
[8]
30
[10]
38
[12]
45
[14]
53
[16]
61
[18]
68
[20]
76
[22]
83
[24]
91
[25]
95
[30
]
114
76
[22]
[250]
155
[500]
35
[750] [1000] [1250] [1500] [1750] [2000] [2250] [2500] [2750] [3000] [3250] [3500] [3750]
50
70
85
105
120
140
155
170
190
205
225
240
260
[240]
25
4
[290]
35
8
[380]
45
17
[390]
45
37
[405]
45
76
[405]
45
115
[400]
45
154
[380]
45
193
[355]
40
231
[320]
35
269
[590]
65
2
[640]
70
6
[730]
80
16
[755]
85
35
[795]
90
74
[815]
90
113
[820]
90
151
[810]
95
190
[790]
90
229
[765]
85
267
[990]
110
5
[1100]
125
15
[1135]
130
34
[1185]
135
73
[1220]
140
111
[1230]
140
149
[1230]
140
188
[1215]
135
227
[1190]
135
267
[1340]
150
2
[1430]
160
14
[1470]
165
33
[1540]
175
72
[1590]
180
110
[1625]
185
148
[1645]
185
187
[1650]
185
226
[1645]
185
264
[1790]
200
13
[1860]
210
32
[1970]
225
71
[2035]
230
109
[2065]
235
147
[2095]
235
186
[2100]
235
224
[2090]
235
261
[2120]
200
11
[2195]
250
31
[2310]
260
70
[2395]
270
108
[2450]
275
146
[2480]
280
184
[2485]
280
221
[2475]
280
260
[2450]
275
9
[2535]
285
28
[2675]
300
66
[2780]
315
104
[2850]
320
143
[2895]
325
181
[2915]
330
219
[2915]
330
257
[2720]
305
7
[2880]
325
26
[3040]
345
64
[3170]
360
102
[3260]
370
140
[3310]
375
177
[3340]
375
218
[3350]
380
254
[2990]
340
5
[3120]
355
24
[3420]
385
62
[3560]
400
100
[3670]
415
137
[3730]
420
175
[3760]
425
215
[3770]
425
250
[3260]
370
4
[3680]
415
21
[3790]
430
61
[3940]
445
99
[4040]
455
135
[4100]
465
173
[4120]
465
211
[4130]
465
248
[290]
30
308
[290]
30
346
[210]
25
385
[170]
20
424
[135]
15
462
[120]
15
484
[730]
80
306
[690]
80
345
[650]
75
384
[610]
70
423
[570]
65
461
[550]
60
482
[420]
45
577
[1160]
130
305
[1120]
125
345
[1080]
120
383
[1040]
120
422
[1000]
115
460
[980]
110
479
[860]
95
575
[1625]
185
303
[1590]
180
342
[1550]
175
380
[1500]
170
418
[1440]
165
457
[1410]
160
476
[1290]
145
571
[2070]
235
299
[2035]
230
337
[1995]
225
375
[1955]
220
414
[1910]
215
453
[1890]
215
473
[1700]
190
567
[2455]
275
296
[2420]
270
334
[2380]
270
372
[2340]
265
410
[2300]
260
449
[2280]
260
469
[2120]
240
562
[2900]
330
294
[2870]
325
333
[2830]
320
371
[2785]
315
408
[3170]
360
441
[3150]
355
459
[2530]
285
556
[3340]
375
290
[3310]
375
327
[3270]
370
367
[3220]
365
404
[3590]
405
436
[3570]
405
454
[2940]
330
550
[3760]
425
286
[3730]
420
321
[3690]
415
363
[3640]
410
399
[3980]
450
432
[3960]
445
449
[3400]
385
542
[4130] [4490] [4860]
465
505
550
283
279
276
[4100] [4480]
465
505
315
308
[4070] [4450]
460
500
359
355
4050]
460
395
[3980]
450
432
[3960]
445
449
83
[24]
91
[25]
95
[30
[3540]
400
3
[4090]
460
20
[4160]
470
59
[4320]
490
96
[4410]
500
132
[4470]
505
170
[4480]
505
208
[4480]
505
245
[3810]
430
2
[4500]
510
19
[4520]
510
57
[4700]
530
94
[4780]
540
130
[4840]
545
168
[4850]
550
204
[4860]
550
241
[4080]
460
2
[4800]
540
17
[4890]
550
55
[5070]
570
91
[5150]
580
127
[5210]
590
164
[4350]
490
1
[5100]
575
14
[5260]
595
51
[5450]
615
87
[5520]
625
123
[5590]
630
160
[4620]
520
1
[5400]
610
14
[5630]
635
45
[5830]
660
81
[5890]
665
117
[200]
25
3
[240]
25
9
[280]
30
23
[300]
35
46
[320]
35
93
[320]
35
142
[310]
35
190
[290]
35
237
[270]
30
286
[240]
25
334
[220]
25
382
[190]
20
429
[170]
20
477
[150]
15
525
[120]
15
572
[90]
10
596
114
[330]
35
713
[500] [1000] [1500] [2000] [2500] [3000] [3500] [3750]
35
70
105
140
170
205
240
260
[490]
55
7
[590]
65
21
[610]
70
45
[630]
70
92
[650]
75
140
[650]
75
187
[640]
70
235
[620]
70
283
[590]
65
331
[570]
65
378
[540]
60
426
[510]
60
474
[480]
55
522
[450]
50
569
[440]
50
593
[330]
35
713
[990]
110
5
[1170]
130
19
[1210]
135
42
[1260]
140
89
[1300]
145
137
[1330]
150
184
[1340]
150
231
[1320]
150
279
[1300]
145
326
[1270]
145
374
[1240]
140
422
[1210]
135
469
[1170]
130
517
[1150]
130
564
[1140]
130
587
[1040]
120
706
[1570]
175
3
[1730]
195
17
[1790]
200
39
[1890]
215
85
[1960]
220
131
[2010]
225
178
[2030]
230
226
[2030]
230
274
[2020]
230
322
[1980]
225
369
[1960]
220
416
[1920]
215
462
[1880]
210
510
[1860]
210
556
[1840]
210
580
[1750]
200
696
[2140]
240
1
[2290]
260
13
[2350]
265
35
[2530]
285
79
[2620]
295
124
[2670]
300
170
[2850]
320
217
[2700]
305
265
[2690]
305
312
[2660]
300
360
[2640]
300
407
[2630]
300
451
[2600]
295
501
[2570]
290
546
[2560]
290
566
[2470]
280
682
[2830]
320
8
[2920]
330
34
[3170]
360
77
[3280]
370
118
[3330]
375
166
[3410]
385
212
[3370]
380
254
[3360]
380
305
[3330]
375
349
[3320]
375
394
[3310]
375
440
[3290]
370
484
[3260]
370
531
[3230]
365
553
[3140]
355
672
[3330]
375
3
[3480]
395
33
[3820]
430
75
[3940]
445
113
[4000]
450
164
[4030]
455
297
[4040]
455
246
[4030]
455
297
[4010]
455
339
[3990]
450
387
[3940]
445
430
[3920]
445
473
[3900]
440
522
[3880]
440
544
[3800]
430
658
[3820]
430
2
[4050]
460
28
[4460]
505
59
[4600]
520
104
[4660]
525
153
[4700]
530
193
[4710]
530
235
[4700]
530
286
[4680]
530
326
[4070]
460
1
[4330]
490
22
[4780]
540
43
[4930]
560
96
[4990]
565
142
[5030
570
187
[5040]
570
224
C-1
}
Torque [lb-in ]
Nm
Speed RPM
C-1-5
245 c3m/r [14.3/9r ]in
2000 Series
Performance Data
[.5]
1,9
[1]
in production.
7,5
[4]
15
[6]
23
[8]
30
[10]
38
[12]
Flow LPM [GPM]
Continuous
3,8
[2]
Peak
45
[14]
53
[16]
61
[18]
Intermittent
No Operation
68
[20]
76
[22]
83
[24]
91
[25]
95
[30
]
114
305 c3m/r [18.3/7r ]in
[.5]
1,9
[1]
3,8
[2]
7,5
[4]
15
[6]
23
[8]
30
[10]
Flow LPM [GPM]
38
[12]
45
[14]
53
[16]
61
[18]
68
[20]
76
[22]
83
[24]
91
[25]
95
[30
]
114
C-1-6
[250]
155
[500]
35
[500]
55
4
[610]
70
12
[620]
70
24
[680]
75
49
[620]
70
74
[600]
70
98
[570]
65
123
[530]
60
148
[480]
55
172
[430]
50
196
[370]
40
221
[320]
35
246
[240]
25
271
[180]
20
296
[150]
15
308
[1050]
120
2
[1180]
135
11
[1210]
135
24
[1250]
140
49
[1270]
145
74
[1270]
145
98
[1250]
140
122
[1220]
140
147
[1180]
135
172
[1120]
125
196
[1060]
120
221
[980]
110
245
[920]
105
270
[870]
100
294
[840]
95
307
[680]
75
365
[250]
155
[500]
35
[410]
45
4
[450]
50
14
[460]
50
29
[470]
55
60
[460]
50
91
[460]
50
122
[440]
50
153
[410]
45
184
[380]
40
215
[340]
40
246
[290]
30
277
[250]
30
308
[200]
25
339
[150]
15
370
[120]
15
385
[850]
95
2
[930]
105
13
[960]
110
28
[1000]
115
59
[1020]
115
90
[1010]
115
121
[1000]
115
152
[960]
110
183
[910]
105
214
[860]
95
245
[810]
90
276
[800]
90
306
[710]
80
337
[670]
75
369
[660]
75
384
[520]
60
462
[750] [1000] [1250] [1500] [1750] [2000] [2250] [2500] [2750] [3000] [3250] [3500] [3750]
50
70
85
105
120
140
155
170
190
205
225
240
260
[1420]
160
12
[1460]
165
27
[1540]
175
58
[1550]
175
89
[1560]
175
120
[1550]
175
150
[1530]
175
182
[1500]
170
213
[1460]
165
244
[1420]
160
275
[1350]
155
304
[1300]
145
337
[1240]
140
367
[1210]
135
382
[1080]
120
460
[1850]
210
11
[1900]
215
26
[1980]
225
56
[2040]
230
87
[2080]
235
118
[2110]
240
148
[2100]
235
180
[2080]
235
211
[2040]
230
242
[2000]
225
273
[1910]
215
302
[1870]
210
334
[1790]
200
364
[1750]
200
379
[1620]
185
458
[750] [1000] [1250] [1500] [1750] [2000] [2250] [2500] [2750] [3000] [3250] [3500]
50
70
85
105
120
140
155
170
190
205
225
240
[1750]
200
11
[1800]
205
23
[1880]
210
48
[1920]
215
72
[1940]
220
97
[1940]
220
121
[1920]
215
145
[1870]
210
170
[1820]
205
194
[1760]
200
218
[1680]
190
243
[1620]
185
268
[1550]
175
293
[1520]
170
305
[1360]
155
362
[2330]
260
10
[2400]
270
22
[2500]
280
47
[2560]
290
72
[2600]
295
96
[2610]
295
120
[2600]
295
144
[2560]
290
168
[2500]
280
192
[2440]
275
217
[2360]
265
241
[2300]
260
266
[2240]
255
290
[2200]
250
303
[2040]
230
360
[2870]
325
10
[2970]
335
22
[3120]
355
47
[3230]
365
71
[3290]
370
95
[3310]
375
119
[3300]
375
143
[3260]
370
167
[3210]
365
191
[3140]
355
215
[3050]
345
239
[2990]
340
263
[2920]
330
288
[2890]
325
300
[2720]
305
357
[3440]
390
9
[3510]
395
20
[3690]
415
45
[3810]
430
69
[3880]
440
93
[3920]
440
117
[3920]
440
142
[3900]
440
165
[3870]
440
188
[3800]
440
212
[3710]
420
236
[3560]
400
260
[3420]
385
285
[3340]
375
298
[3140]
355
356
[3930]
445
8
[4050]
460
19
[4260]
480
43
[4390]
495
66
[4470]
505
90
[4530]
510
113
[4530]
510
138
[4510]
510
160
[4480]
505
183
[4420]
500
207
[4370]
495
231
[4190]
475
258
[4020]
455
283
[3930]
445
295
[3810]
430
352
[4410]
500
6
[4600]
520
18
[4840]
545
42
[4970]
560
64
[5070]
575
86
[5150]
580
110
[5150]
580
133
[5120]
580
156
[5080]
575
178
[5050]
570
202
[5020]
565
226
[4820]
545
255
[4630]
525
280
[4520]
510
293
[4900]
555
3
[5140]
580
17
[5410]
610
40
[5560]
630
61
[5660]
640
83
[5760]
650
106
[5760]
650
128
[5730]
645
152
[5690]
645
174
[5380]
610
1
[5680]
640
15
[5980]
675
38
[6130]
695
58
[6250]
705
80
[6370]
720
102
[6370]
720
124
[6220] [6750] [7290] [7820]
705
765
825
885
13
11
8
6
[6550] [7120] [7690]
740
805
870
36
34
33
[6710] [7290]
760
825
55
52
[6840]
775
77
[2320]
260
10
[2400]
270
25
[2510]
285
54
[2580]
290
84
[2630]
295
115
[2650]
300
146
[2640]
300
177
[2600]
295
209
[2570]
290
240
[2520]
285
271
[2460]
280
300
[2390]
270
332
[2330]
265
362
[2300]
260
377
[2180]
245
456
[2780]
315
9
[2860]
325
23
[3010]
340
53
[3110]
350
83
[3170]
360
113
[3200]
360
144
[3190]
360
175
[3160]
355
207
[3120]
355
238
[3060]
345
269
[3010]
340
298
[2940]
330
330
[2880]
325
360
[2860]
325
375
[2720]
305
453
[3250]
365
8
[3340]
375
22
[3480]
395
51
[3590]
405
81
[3670]
415
111
[3730]
420
142
[3760]
425
173
[3760]
425
204
3740]
425
235
[3700]
420
266
[3630]
410
295
[3560]
400
327
[3460]
390
357
[3410]
385
372
[3260]
370
450
[3260]
370
450
}
[3650]
410
6
[3780]
425
20
[3980]
450
49
[4120]
465
78
[4210]
475
108
[4250]
480
139
[4260]
480
170
[4230]
480
201
[4180]
470
232
[4130]
465
263
[4110]
465
291
[4010]
455
323
[3960]
445
353
[3950]
445
367
[3790]
430
447
Torque [lb-in ]
Nm
Speed RPM
[4100]
465
5
[4320]
490
19
[4450]
505
48
[4580]
515
76
[4680]
530
106
[4730]
535
137
[4740]
535
168
[4710]
530
198
[4660]
525
227
[4610]
520
258
[4610]
520
288
[4510]
510
318
[4460]
505
344
[4470]
505
363
[4540]
515
4
[4770]
540
18
[4910]
555
47
[5050]
570
73
[5160]
585
104
[5210]
560
135
[5220]
600
165
[5190]
585
195
[5140]
580
223
[5090]
575
253
[4980]
560
4
[5210]
590
17
[5380]
610
47
[5520]
625
71
[5630]
635
102
[5720]
645
133
[5730]
645
162
[5430]
615
3
[5660]
640
15
[5850]
660
46
[5980]
675
69
[6110]
690
101
[6230]
705
103
[5870]
665
2
[6110]
690
14
[6320]
715
45
[6440]
730
67
[6590]
745
99
[6310]
715
1
[6570] [6950]
740
785
12
10
[6780] [7250]
765
820
44
42
[6910]
780
65
2000 Series
395 c3m/r [24.3/0r ]in
Performance Data
[.5]
1,9
[1]
in production.
3,8
[2]
7,5
[4]
15
[6]
23
[8]
30
[10]
Flow LPM [GPM]
38
[12]
Continuous
Peak
Intermittent
No Operation
45
[14]
53
[16]
61
[18]
68
[20]
76
[22]
490 c3m/r [29.3/8r ]in
[.5]
1,9
[1]
3,8
[2]
7,5
[4]
15
[6]
23
[8]
Flow LPM [GPM]
30
[10]
38
[12]
45
[14]
53
[16]
61
[18]
68
[20]
76
[22]
83
[24]
91
[26]
98
[28]
106
[30
]
114
[250]
155
[500]
35
[670]
75
2
[920]
105
7
[950]
105
14
[980]
110
30
[980]
110
45
[980]
110
61
[920]
105
76
[860]
95
91
[790]
90
106
[720]
80
122
[630]
70
137
[550]
60
153
[450]
50
168
[360]
40
184
[270]
30
199
[1600]
180
1
[2000]
225
6
[2060]
235
13
[2130]
240
29
[2120]
240
44
[2110]
240
60
[2050]
230
75
[1990]
225
90
[1930]
220
105
[1870]
210
121
[1770]
200
136
[1670]
190
152
[1570]
175
168
[1480]
165
184
[1390]
155
195
[1260]
140
212
[1130]
125
230
[750] [1000] [1250] [1500] [1750] [2000]
50
70
85
105
120
140
[2990]
340
5
[3110]
350
12
[3230]
365
28
[3230]
365
43
[3220]
365
59
[3170]
360
74
[3120]
355
90
[3055]
345
105
[2990]
340
120
[2890]
325
135
[2800]
315
151
[2700]
305
167
[2600]
295
183
[2510]
285
194
[2370]
270
211
[2240]
255
229
[3900]
440
4
[4080]
460
10
[4270]
480
27
[4300]
485
42
[4330]
490
58
[4300]
485
73
[4260]
480
89
[4185]
475
104
[4110]
465
119
[4020]
455
134
[3940]
445
150
[3830]
435
165
[3730]
420
181
[3640]
410
192
[3520]
400
209
[3400]
385
277
[4880]
550
2
[5110]
575
9
[5350]
605
26
[5370]
605
41
[5400]
610
57
[5390]
610
72
[5370]
605
87
[5300]
600
102
[5230]
590
118
[5140]
580
133
[5060]
570
149
[4960]
560
164
[4860]
550
179
[4770]
540
190
[4630]
525
207
[4500]
510
224
83
[24]
91
[26]
98
[28]
[6320]
715
7
[6370]
720
24
[6420]
725
39
[6470]
730
55
[6460]
730
70
[6460]
730
85
[6400]
725
100
[6340]
715
116
[6260]
705
131
[6180]
700
146
[6070]
685
161
[5970]
675
177
106
[30]
[7380] [7980]
835
900
22
20
[7470] [8225]
845
930
37
35
[7550]
855
52
[7550]
855
68
[7560]
855
84
114
[35]
132
[250]
155
[500]
35
[560]
65
4
[770]
85
9
[790]
90
18
[810]
90
37
[820]
90
57
[820]
90
76
[800]
90
95
[770]
85
114
[740]
85
133
[690]
80
153
[640]
70
172
[580]
65
191
[510]
60
210
[440]
50
230
[350]
40
249
[270]
30
268
[180]
20
287
[1310]
150
3
[1540]
175
9
[1580]
180
18
[1660]
190
37
[1700]
190
56
[1700]
190
75
[1700]
190
94
[1680]
190
113
[1640]
185
132
[1590]
180
152
[1530]
170
171
[1470]
165
190
[1390]
155
209
[1330]
150
229
[1240]
140
248
[1150]
130
267
[1060]
120
286
[840]
95
335
[1760]
200
334
[750] [1000] [1250] [1500] [1750] [2000] [2250] [2500] [2750]
50
70
85
105
120
140
155
170
190
[2290]
260
9
[2360]
265
18
[2480]
280
37
[2550]
290
56
[2580]
290
75
[2590]
295
94
[2570]
290
113
[2530]
285
132
[2480]
280
152
[2420]
275
171
[2370]
270
190
[2290]
260
209
[2220]
250
228
[2130]
240
247
[2050]
230
265
[1960]
220
284
[1760]
200
334
[3080]
350
8
[3180]
360
17
[3320]
375
36
[3420]
385
55
[3460]
390
74
[3480]
395
93
[3470]
390
112
[3430]
390
131
[3370]
380
150
[3310]
375
170
[3260]
370
189
[3170]
360
208
[3100]
350
227
[3020]
340
246
[2930]
330
264
[2850]
320
283
[2640]
300
333
[3780]
430
8
[3930]
445
17
[4130]
465
36
[4250]
480
54
[4300]
485
73
[4320]
490
92
[4310]
485
111
[4280]
485
129
[4220]
475
149
[4160]
470
169
[4110]
465
188
[4030]
455
207
[3950]
445
225
[3880]
440
244
[3790]
430
261
[3710]
420
281
[3480]
395
332
[4480]
505
7
[4680]
530
16
[4940]
560
35
[5080]
575
52
[5130]
580
71
[5160]
585
90
[5150]
580
109
[5120]
580
127
[5060]
570
146
[5010]
565
167
[4960]
560
186
[4880]
550
206
[4800]
540
224
[4730]
535
242
[4650]
525
259
[4570]
515
277
[5170]
585
7
[5430]
615
15
[5740]
650
34
[5920]
670
50
[5960]
675
69
[6000]
680
88
[5990]
675
106
[5960]
675
124
[5910]
670
144
[5870]
665
164
[5820]
660
184
[5880]
665
6
[6180]
700
14
[6550]
740
33
[6750]
765
49
[6800]
770
68
[6840]
775
86
[6830]
770
103
[6580]
745
5
[6840]
775
13
[7230]
815
31
[7420]
840
47
[7270] [7980]
820
900
4
3
[7500] [8170]
845
925
11
10
[7880]
890
28
[8000]
905
45
C-1
}
Torque [lb-in ]
Nm
Speed RPM
C-1-7
2000 Series
Ports
Dimensions
or
1 1/16 -12 UN-2B SAE O-ring Ports (Positioned 180° Apart) (2)
7/16 -20 UNF-2B SAE O-ring Case Drain Port (1) or
7/8 -14 UNF-2B SAE O-ring End Ports (2)
G 1/2 (BSP) Staggered Ports (2)
G 1/4 (BSP) Case Drain Port (1) or
Manifold Mount
7/16 -20 UNF-2B SAE O-ring Case Drain Port (1)
7/8 -14 UNF-2B SAE O-ring Staggered Ports (2)
Standard Mount
Standard Rotation Viewed from Shaft End
Port A Pressurized — CW
Port B Pressurized — CCW
Standard Mount
Port B
YY Max.
XX
YY Max.
Port B
Y Max.
X
1-1/16-12 UN-2B SAE O-ring Ports
(Positioned 180º Apart)
7/8-14 UNF-2B SAE O-ring End Ports
Standard Mount Motor Dimensions
C-1-8
Displacement X
cm 3/r [in3/r]
mm [inch]
Y
mm [inch]
XX
mm [inch]
YY
mm [inch]
80 [4.9]
100 [6.2]
130 [8.0]
160 [9.6]
195 [11.9]
245 [14.9]
305 [18.7]
395 [24.0]
490 [29.8]
184,2 [7.25]
189,0 [7.44]
195,4 [7.69]
195,4 [7.69]
202,2 [7.96]
211,1 [8.31]
222,3 [8.75]
238,6 [9.39]
255,8 [10.07]
139,2 [5.48]
143,8 [5.66]
150,2 [5.92]
150,2 [5.92]
157,0 [6.18]
166,0 [6.54]
177,4 [6.99]
193,3 [7.61]
210,7 [8.30]
185,4 [7.30]
190,3 [7.49]
196,6 [7.74]
196,6 [7.74]
203,2 [8.00]
212,4 [8.36]
223,5 [8.80]
239,8 [9.44]
270,1 [10.12]
136,9 [5.39]
141,5 [5.57]
147,9 [5.83]
147,9 [5.83]
154,7 [6.09]
163,7 [6.45]
175,1 [6.90]
191,0 [7.52]
208,4 [8.21]
2000 Series
Ports
Dimensions
or
G 1/4 (BSP) Case Drain Port (1)
Standard Mount with
Integral Relief Valve
Standard Mount with Integral Relief Valve
Port B
Y Max.
2X 93.0/92.4
[3.66/3.64]
X
C-1
64.3/63.8
[2.53/2.51]
Case Drain
7/16-20 UNF-2B
SAE O-ring Port
or
G 1/4 (BSP)
Standard mount motor dimensions
Displacement
cm 3/r [in 3/r]
X
mm [inch]
Y
mm [inch]
80 [4.9]
100 [6.2]
130 [8.0]
160 [9.6]
195 [11.9]
245 [14.9]
305 [18.7]
395 [24.0]
490 [29.8]
137,0 [5.40]
141,6 [5.58]
147,9 [5.83]
147,9 [5.83]
154,8 [6.10]
163,7 [6.45]
175,1 [6.90]
191,1 [7.53]
208,4 [8.21]
184,5 [7.26]
189,0 [7.44]
195,4 [7.69]
195,4 [7.69]
202,2 [7.96]
211,1 [8.31]
222,6 [8.76]
238,6 [9.39]
255,8 [10.07]
C-1-9
2000 Series
Ports
Dimensions
or
Manifold Mount
Wheel Mount
Wheel Mount
YY Max.
XX
Port B
YY Max.
Y Max.
X
Port B
1 1/16 -12 UN-2B SAE O-ring Ports
(Positioned 180 Apart)
Wheel Mount Motor Dimensions
Displacement
cm3/r [in3/r]
80 [4.9]
100 [6.2]
130 [8.0]
160 [9.6]
195 [11.9]
245 [14.9]
305 [18.7]
395 [24.0]
490 [29.8]
C-1-10
X
mm [inch]
96,8 [3.81]
101,3 [3.99]
107,8 [4.25]
107,8 [4.25]
114.6 [4.51]
123,5 [4.87]
135,0 [5.32]
150,9 [5.94]
168,2 [6.63]
Y
mm [inch]
144,0 [5.67]
148,9 [5.86]
155,2 [6.11]
155,2 [6.11]
161,8 [6.37]
171,0 [6.73]
182,1 [7.17]
198,4 [7.81]
215,7 [8.49]
XX
mm [inch]
YY
mm [inch]
99,1[3,90]
103,6 [4.08]
110,1 [4.34]
110,1 [4.34]
116,8 [4.60]
125,8 [4.96]
137,4 [5.41]
153,2 [6.03]
170,7 [6.72]
145,3 [5.72]
150,2 [5.91]
156,5 [6.16]
156,5 [6.16]
163,1 [6.42]
172,3 [6.78]
183,4 [7.22]
199,7 [7.86]
217,0 [8.54]
2000 Series
Ports
Dimensions
Wheel Mount with Intergal
Relief Valve
Wheel Mount with Integral Relief Valve
Port B
Y Max.
X
93.0/92.4
2X [3.66/3.64]
C-1
64.3/63.8
[2.53/2.51]
Case Drain
7/16-20 UNF-2B
SAE O-ring Port
or G 1/4 (BSP)
Displacement
cm3/r [in3/r]
80 [4.9]
100 [6.2]
130 [8.0]
160 [9.6]
195 [11.9]
245 [14.9]
305 [18.7]
395 [24.0]
490 [29.8]
X
mm [inch]
96,9 [3.82]
101,4 [4.00]
107,8 [4.25]
107,8 [4.25]
114.6 [4.52]
123,5 [4.87]
135,0 [5.32]
151,0 [5.95]
168,2 [6.63]
Y
mm [inch]
144,3 [5.68]
148,9 [5.86]
155,2 [6.11]
155,2 [6.11]
162,1 [6.38]
171,0 [6.73]
182,4 [7.18]
198,4 [7.81]
215,7 [8.49]
C-1-11
2000 Series
Ports
Dimensions
or
Manifold Mount
Bearingless
Bearingless
YY Max.
XX
Port B
Port B
Y Max.
X
MAT’L
C 35,86 [1.412] Dia.
D 34,04 [1.340] Dia.
E 81,0 [3.19 ] Min. Full Form Dia.
F 86,1 [3.39 ] Max.
G 62,10 [2.445] Full Form Dia.
H 38,40 [1.512] Dia.
K
J 43,7 [1.72 ] Dia.
K 25,91 [1.020]
L 8,25 [.325]
M 0,89 [.035]
L
N15º
M
101,60/101,47
[4.000/3.995]
Pilot Dia.
1 1/16-12 UN-2B SAE O-ring Ports
C
D
E
N
F
G
H
J
Mating Coupling Blank
Eaton Part No. 13307-003
YY Max.
16,8/15,2
[.66/.60]
157,5
[6.20]
Max. (2)
6.7/6,0
[.26/.24]
For 2000 Series Bearingless
Motor application information contact your Eaton
representative (mating
coupling blanks available
from Eaton Hydraulics).
127,0
[5.00]
Dia.
13,85/13,33
[.545/.525]
Dia. Thru (4)
119,2
[4.69]
Sq. Max.
14,22 [.560]
Min. (4)
O-ring Seal
Furnished
with Motor
Note:
After machining blank, part
must be hardened per Eaton
specification.
24,06/23,54
[.947/.927]
Bearingless Motor Dimensions
C-1-12
Displacement X
mm [inch]
cm3/r [in3/r]
Y
mm [inch]
XX
mm [inch]
YY
mm [inch]
80 [4.9]
100 [6.2]
130 [8.0]
160 [9.6]
195 [11.9]
245 [14.9]
305 [18.7]
395 [24.0]
490 [29.8]
126,5 [4.98]
131,4 [5.17]
137,7 [5.42]
137,7 [5.42]
144,3 [5.68]
153,5 [6.04]
164,6 [6.48]
180,9 [7.12]
198,2 [7.80]
81,3 [3.20]
85,8 [3.38]
92,2 [3.63]
92,2 [3.63]
99,0 [3.90]
107,9 [4.25]
119,4 [4.70]
135,4 [5.33]
152,7 [6.01]
127,8 [5.03]
132,6 [5.22]
139,0 [5.47]
139,0 [5.47]
145,5 [5.73]
154,7 [6.09]
165,9 [6.53]
182,1 [7.17]
199,3 [7.85]
79,0 [3.11]
83,5 [3.29]
89,9 [3.54]
89,9 [3.54]
96,8 [3.81]
105,6 [4.16]
117,1 [4.61]
133,1 [5.24]
150,3 [5.92]
2000 Series
Ports
Dimensions
Bearingless with Integral
Relief Valve
Bearingless with Integral Relief Valve
Port B
Y Max.
X
93.0/92.4
2X [3.66/3.64]
101,60/101,47
[4.000/3.995]
Pilot Dia.
64.3/63.8
[2.53/2.51]
Case Drain
7/16-20 UNF-2B
SAE O-ring Port
or
G 1/4 (BSP)
16,8/15,2
[.66/.60]
C-1
157,5
[6.20]
Max. (2)
6.7/6,0
[.26/.24]
127,0
[5.00]
Dia.
13,85/13,33
[.545/.525]
Dia. Thru (4)
119,2
[4.69]
Sq. Max.
14,22 [.560]
Min. (4)
O-ring Seal
Furnished
with Motor
24,06/23,54
[.947/.927]
Bearingless Motors Dimensions
Displacement
cm 3/r [in 3/r]
X
mm [inch]
Y
mm [inch]
80 [4.9]
100 [6.2]
130 [8.0]
160 [9.6]
195 [11.9]
245 [14.9]
305 [18.7]
395 [24.0]
490 [29.8]
79,0 [3.11]
83,5 [3.29]
89,9 [3.54]
89,9 [3.54]
96,8 [3.81]
105,6 [4.16]
117,1 [4.61]
133,1 [5.24]
150,3 [5.92]
126,8 [4.99]
131,4 [5.17]
137,7 [5.42]
137,7 [5.42]
144,6 [5.69]
153,5 [6.04]
164,9 [6.49]
180,9 [7.12]
198,2 [7.80]
C-1-13
2000 Series
1 Internal spline in mating part to be per
spline data. Specification material to be
ASTM A304, 8620H vacuum degassed
alloy steel carbonize to a hardness of
59-62 HRc with case depth (to 50HRc)
of 0,076 -1,02 [.030 -.040]. Dimensions
apply after heat treat.
2 Mating part to have critical dimensions as
shown. Oil holes must be provided and
open for proper oil circulation.
3 Seal to be furnished with motor for
proper oil circulation thru splines.
Bearingless
18,6/17,5
[.73/.69]
13,0/11,9
[.51/.47]
34,85/34,82
[1.372/1.371]
0,08 [.003]
C
-D- D ia.
4,1/3,5
[.16/.14]
59,0/58,4
[2.32/2.30]
2,54/2,03
[.100/.080]
1,6/0,7
[.06/.03]
2
15,2 [.60] Min . D ia.
Case Flow
Ø 0,13 [.005]
A
Case Flow
R 0,8 [.03] Max .
41,1 [1.62] Min . D ia.
34,41 [1.355] Min .
28,00/27,73
[1.102/1.092] Dia.
-A-
5
R 1,8/1,2
[.07/.05]
15º - 30º
43,4/42,4
[1.71/1.67]
Coupling D ept h
1,6/0,7 [.06/.03]
4,9/4,3 [.19/.17] D ia.
Th ru Oil Hole (2 )
30,3/29,7
[1.19/1.17]
16
4 Some means of maintaining clearance
between shaft and mounting flange must
be provided.
5 Counterbore designed to adapt a standard
sleeve bearing 35,010 -35,040 [1.3784
-1.3795] I.D. by 44,040 -44,070 [1.7339
-1.7350] O.D. (Oilite Bronze Sleeve
Bearing AAM3544-22).
3
4
-B-
Circula r
Major
Finis h
Finis h
Tip R .
Mino r
C-1-14
Fillet R .
Pitch
Fo rm
Spline Pitch..................................................................................................12/24
Pressure Angle...............................................................................................30°
Number of teeth...............................................................................................12
Class of Fit...................................................................................................Ref. 5
Type of Fit......................................................................................................Side
Pitch Diameter........................................................Ref. 25,400000 [1.0000000]
0,21 [.008] | D
Base Diameter.........................Ref. 21,997045 [.8660254]
Major Diameter..................................(27,74 [1.092] Max. 27,59 [1.086] Min.)
Minor Diameter.................................................23,097 - 23,224 [.9093 - .9143]
Form Diameter, Min....................................................................... 29,93 [1.060]
Fillet Radius....................................................................0,64 - 0,76 [.025 - .030]
Tip Radius.......................................................................0,25 - 0,38 [.010 - .015]
Finish......................................................................................................... 1,6 (63)
Involute Profile Variation.................................. +0,000 -0,025 [+.0000 -.0010]
Total Index Variation..................................................................... 0,038 [.0015]
Lead Variation................................................................................ 0,013 [.0005]
Circular Space Width:
Maximum Actual..................................................................... 4,318 [.1700]
Minimum Effective.................................................................. 4,216 [.1660]
Maximum Effective.........................................................Ref. 4,270 [.1681]
Minimum Actual..............................................................Ref. 4,247 [.1672]
Dimension Between Two Pins...............Ref. 19,020 - 19,190 [.7488 - .7555]
Pin Diameter........................................ 4,496 [.1770] Pins to Have 3,38 [.133]
.
Wide Flat for Root Clearance
]
[.38/.36]
2000 Series
Dimensions
[2.25/2.00]
Dia.
6,7/6,0
[.27/.24]
108,8
[4.28]
Max. Sq.
22,1/17,0
Mounting
Options
[.87/.67]
106,38
[4.188]
Dia. Bolt Circle
Four Bolt
22,7/21,8
[.89/.86]
Dia. (4)
20,1 [.79]
Max.
13,72/13,46
[.540/.530]
Dia. Thru (4)
18,6/17,0
[.73/.67]
82,55/82,42
[3.250/3.245]
Pilot Dia.
SAE A — Two Bolt (Standard Motor)
147,638
[5.8125]
Dia.
Bolt Circle18,6/17,0
[.73/.67]
131,1 [5.16] Max.
106,38 [4.188]
134,2
[5.28]
Max. Sq.
13,85/13,33
[.545/.525]
Dia. Thru
(2)
107,95/107,82 6,4 [.25]
82,55/82,42
[4.250/4.245]
22,1 [.87]
[3.250/3.245]
Pilot Dia.
Max.
Pilot Dia.
95,2 [3.75] Dia.
6,7/6,0
[.26/.24]
176,8
SAE 101,60/101,47
B — Two Bolt
[6.96] [4.000/3.995]
Max. Pilot Dia.
146,05
[5.750]
176,8
[6.96]
Max.
101,60/101,47
[4.000/3.995]
Pilot Dia.
146,05
[5.750]
127,00/126,87
[5.000/4.995]
Dia.
9,7/9,1
[.38/.36]
22,1/17,0
[.87/.67]9,7/9,1
[.38/.36]
22,7/22,0
[.89/.87]
107,95/107,82
[4.250/4.245]
Pilot Dia.
95,2 [3.75] Dia.
13,85/13,33
22,7/22,0
[.545/.525]
[.89/.87]
18,6/17,0
[.73/.67]
2,8/2,3
[.11/.09]
13,
[.5
Dia
18,6/17,0
[.73/.67]
14,53/14,14
[.572/.557]
Dia. Thru (2)
C-1
13,
[.5
Dia
Four Bolt (Wheel Motor)
14,53/14,14
[.572/.557]
Dia.6,7/6,0
Thru (2)
[.27/.24]
57,2/50,8
[2.25/2.00]
Dia.
47,3/45,7
[1.85/1.80]
Dia. Thru (4)
20,1 [.79]
Max.
57,2/50,8
18,6/17,0
[2.25/2.00]
[.73/.67]
45°Dia.
2,8/2,3
6,4
[.25]
22,7/21,8
[.11/.09]
22,1 [.87]
[.89/.86]
Max.
Dia. (2)
6,7/6,0
[.27/.24]
22,1/17,0
22,7/21,8
106,38 [4.188] Dia.
[.87/.67]
[.89/.86]
45°
135,7 [5.34] Max.
Dia. (4)
22,1 [.87] Max.
57,2/50,8
[2.25/2.00]
Dia.
147,638
[5.8125]
Dia.
Bolt Circle
13,85/13,33
[.545/.525]
Dia. Thru
176,8 101,60/101,47
[6.96][4.000/3.995]
FourPilot
Bolt Magneto
Max.
Dia.
131,1 [5.16] Max.
146,05
106,38
[4.188]
82,55/82,42
[5.750]
[3.250/3.245]
13,85/13,33
Pilot Dia.
[.545/.525]
22,7/21,8
[.89/.86]
Dia. (4)
82,55/82,42
9,7/9,1
[3.250/3.245]
13,85/13,33
13,85/13,33 [.38/.36]
Pilot Dia.
[.545/.525]
[.545/.525]
Dia.
82,55/82,42
Dia.Thru
Thru (4)
(2)
[3.250/3.245]
Pilot Dia.
3,8/2,8
[.15/.11]
14,53/14,14
[.572/.557]
Dia. Thru (2)
147,638
[5.8125]
Dia.
Bolt Circle
134,2
[5.28]
Max. Sq.
6,7/6,0
[.26/.24]
22,7/21,8
47,3/45,7[.89/.86]
[1.85/1.80]Dia. (2)
6,7/6,0
[.27/.24]
22,1/17,0
[.87/.67]
134,2
[5.28]
Max. Sq.
108,8
[4.28]
Max. Sq.
106,38
[4.188]
Dia. Bolt Circle
13,85/13,33
[.545/.525]
Dia. Thru
6,4
[.25]
106,3882,55/82,42
[4.188] Dia.
18,6/17,0 147,638 22,7/21,8
[.73/.67] [5.8125][.89/.86]
[3.250/3.245]
135,7 [5.34] Max.
Dia. 6,4Dia. (4)
Pilot Dia.
22,1 [.87] Max.
13,72/13,46
[.25]
Bolt Circle
[.540/.530]
134,2
Dia.
Thru (4)
[5.28]
Max. Sq.
18,6/17,0
82,55/82,42
[.73/.67]
[3.250/3.245]
6,4
Pilot Dia.
13,72/13,46
[.25]
108,8 13,85/13,33
[.540/.530]
[4.28] [.545/.525]
Dia. Thru (4)
Max. Sq.Dia. Thru
107,95/107,82
22,7/21,8
[4.250/4.245]
[.89/.86]
47,3/45,7
Pilot
Dia.
106,38
Dia. (4)
Dia.
[4.188] 95,2 [3.75]20,1
[.79] [1.86/1.80]
Dia. Bolt Circle
Max.
6,7/6,0
108,8 22,7/22,0
[.26/.24]
[4.28] [.89/.87]
Max. Sq.
22,7/21,8
131,1 [5.16] Max.
[.89/.86]
18,6/17,0
106,38
Dia. (4)
106,38
[4.188]
[.73/.67]
[4.188]
20,1 [.79]
127,00/126,87
Dia. Bolt Circle
Max. 3,8/2,8
[5.000/4.995]
[.15/.11]
Dia.
131,1 [5.16] Max.
C-1-15
18,6/17,0
13,
[.5
Dia
(2)
2000 Series
Dimensions
Shafts
1 Inch Straight
395 [3500]
395
Max.[3500]
Torqu e
Max.
Torqu e
Nm [lb-in]
Nm [lb-in]
1 1/4 Inch Tapered
52,1/49,8 [2.05/1.96] End of Shaft
52,4/49,7
[2.06/1.96]
End of Shaft
to Mounting
Surface (Std)
to Mounting Surface (Std)
1/4-20 UNC x
1/4-20
UNC
x
15,5 [.61]
Deep
15,5 [.61] Deep
18,5 [.73]
18,5 [.73]
25,40/25,34
25,40/25,34
[1.000/.998]
[1.000/.998]
Dia.
Dia.
28,28/27,88
28,28/27,88
[1.113/1.098]
[1.113/1.098]
25,40 [1.000] Dia.
25,40
[1.000][.251/.250]
Dia.
x 6,38/6,35
xWoodruff
6,38/6,35Key
[.251/.250]
Woodruff Key
768 [6800]
768
Max.[6800]
Torqu e
Max.
Torqu e
Nm [lb-in]
Nm [lb-in]
105,2/102,9 [4.14/4.05] End of Shaft
105,5/102,8
End of Shaft
to Mounting [4.15/4.05]
Surface (Whl)
to Mounting Surface (Whl)
12,7 [.50]
12,7 [.50]
25,9/24,9
25,9/24,9
[1.02/.98]
[1.02/.98]
1-20 UNEF
1-20 UNEF
4,1 [.16]
4,1
Dia.[.16]
Thru
Dia. Thru
38,4 [1.51]
38,4
Max.[1.51]
Coupling
Max. Coupling
31,7 [1.250] Dia.
31,7 [1.250]
Dia.
55,1 [2.17]
55,1 [2.17]
SAE J501 Standard Tapered Shaf t
SAE
J501
Standard
125,00
0,17
Taper perTapered
Mete rShaf t
125,00 .002
0,17 Taper
Taper per
per Foot]
Mete r
[1.500
[1.500 .002 Taper per Foot]
7,963/7,937
7,963/7,937
[.3135/.3125]
[.3135/.3125]
Square Key
Square Key
3,97/3,63 [.156/.143]
3,97/3,63
[.156/.143]
at Large End
of Tape r
at Large End of Tape r
38,1 [1.50]
38,1 [1.50]
Hub
Hub:
Recommended Torque
Recommended
Torque
(373 Nm [275 lb-ft]
Dry) :
(373
(305 Nm [275
[225 lb-ft] Dry)
Lub)
(305
[225required
lb-ft] Lub)
Plus Nm
Torque
t o
Plus
required
t o
align Torque
the slotted
nut with
align
the slotted
nut with
the Shaft
Crosshole.
the Shaft Crosshole.
36,6 [1.44] Across Flats
36,6 [1.44] Across Flats
1 1/4 Inch Straight
768 [6800]
768
Max.[6800]
Torqu e
Max.
Torqu e
Nm [lb-in]
Nm [lb-in]
7,963/7,937
7,963/7,937
[.3135/.3125]
[.3135/.3125]
35,34/35,05
35,34/35,05
[1.391/1.380]
[1.391/1.380]
3/8-16 UNC
3/8-16
UNCDeep
x 19,0 [.75]
x 19,0
[.75] Deep[1.250/1.248] Dia.
31,75/31,69
31,75/31,69 [1.250/1.248] Dia.
C-1-16
25 mm Straight
56,4/54,4 [2.22/2.14] End of Shaft
56,6/54,4
[2.23/2.14]
End of Shaft
to Mounting
Surface (Std)
32,6/30,9 [1.28/1.22]
32,6/30,9 [1.28/1.22]
47,3 [1.86]
47,3
Max.[1.86]
Coupling
Max. Coupling
395 [3500]
395
Max.[3500]
Torqu e
Max.
Torqu e
Nm [lb-in]
Nm [lb-in]
28,00/27,66
28,00/27,66
[1.102/1.089]
[1.102/1.089]
M8 x
M8
1.25x-6H 21,6
1.25
[.85] -6H
Min.21,6
Deep
[.85] Min. Deep
52,1/49,8 [2.05/1.96] End of Shaft
52,4/49,7
[2.06/1.96]
End of Shaft
to Mounting
Surface (Std)
7,999/7,965
7,999/7,965
[.3149/.3136]
[.3149/.3136]
25,00/24,97
25,00/24,97
[.984/.983] Dia.
[.984/.983] Dia.
8,7/4,5 [.34/18]
8,7/4,5 [.34/18]
32,0/31,7 [1.26/1.24]
32,0/31,7 [1.26/1.24]
395 [3500]
395
Max.[3500]
Torqu e
Max.
Torqu e
Nm [lb-in]
Nm [lb-in]
38,1 [1.50]
38,1
Max.[1.50]
Coupling
Max. Coupling
2000 Series
Dimensions
Shafts
32 mm Straight
768 [6800]
Max. Torqu e
Nm [lb-in]
10,00/9,96
768
[6800]
[.394/.392]
Max. Torqu e
35,0/34,7
Nm [lb-in]
[1.38/1.37]
10,00/9,96
[.394/.392]
35,0/34,7
32,017/31,991
[1.38/1.37]
M8 x
[1.2605/1.2595]
1.25 -6H
21,6 [.85]
Min Depth
32,017/31,991
M8 x
[1.2605/1.2595]
1.25 -6H
21,6 [.85]
Min Depth
SAE 6B Splined
395 [3500]
Max. Torqu e
Nm [lb-in]
65,8/63,5 [2.59/2.50] End of Shaft
9,2/4,5 [.36/.18]
45,7/45,3 [1.80/1.74]
65,8/63,5 [2.59/2.50] End of Shaft
9,2/4,5 [.36/.18]
45,7/45,3 [1.80/1.74]
56,4 [2.22]
Max. Coupling
56,4 [2.22]
Max. Coupling
768 [6800]
Max. Torqu e
Nm
[lb-in]
1
56,4/54,4 [2.22/2.14] End of Shaft
1 /4 -14 Tooth Splined to Mounting Surface (Std)
45,5 [1.79] Max.
31,75
Coupling
[1.250]
768
Flat[6800]
Root Side Fit,
33,0 [1.30]
Dia.
Max.
Torqu e
14 Tooth
56,4/54,4 [2.22/2.14]
EndFull
of Shaft
Min.
Nm
[lb-in]
12/24 Spline
to Mounting Surface
(Std)
Spline Depth
to Fit ANSI
45,5 [1.79] Max.
B92.1 1976
31,75
Coupling
[1.250]
Flat Root Side Fit,
33,0 [1.30]
Dia.
14 Tooth
Min. Full
3/8-16
UNC
12/24 Spline
Spline Depth
[.75] Min. Depth
to19,0
Fit ANSI
26,36/26,11
B92.1 1976
[1.038/1.028]
3/8-16 UNC
19,0 [.75] Min. Depth
26,36/26,11
[1.038/1.028]
395 [3500]
Max. Torqu e
Nm [lb-in]
Spline Per
SAE J499
52,1/49,8 [2.05/1.96] End of Shaft
21,16/20,90
[.833/.823]
25,35/25,29
[.998/.996] 52,1/49,8 [2.05/1.96] End of Shaft
Dia.
25,35/25,29
1/4-20 UNC x [.998/.996]
Dia.
Spline15,2
Per [.60] Deep
22,75
SAE J499
[.896]
Min. Full
Depth
Spline
1/4-20 UNC x
15,2 [.60] Deep
22,75
[.896]
Min. Full
Depth
Spline
141 [1250]
Max. Torqu e
Nm [lb-in]
13 Tooth Splined
21,16/20,90
[.833/.823]
28,8 [1.13] Max.
Coupling Length
C-1
28,8 [1.13] Max.
Coupling Length
42,2/40,1 [1.66/1.58] End of Shaft
18,60/18,36
Spline to Fit SAE J498b
[.732/.723] Dia.
141
Flat [1250]
Root Side Fit 13
Max.
Tooth Torqu
16/32 eSpline 21,806/21,678 42,2/40,1 [1.66/1.58] End of Shaft
[.8585/.8535]
Nm [lb-in]
Dia.
Spline to Fit SAE J498b
Flat Root Side Fit 13
Tooth 16/32 Spline 21,806/21,678
15,2
[.60]
[.8585/.8535]
Min.
Dia. Full Spline
15,2 [.60]
Min. Full Spline
18,60/18,36
[.732/.723] Dia.
30,8 [1.21] Max.
Coupling Length
30,8 [1.21] Max.
Coupling Length
C-1-17
2000 Series
These curves indicate the
radial load capacity on
the motor shaft at various
locations with an allowable
external thrust load of 454
kg [1000 lb]. Note:
Case pressure will increase
the allowable inward thrust
load and decrease the
allowable outward thrust
load. Case pressure will
push outward on the shaft at
61 kg/7 Bar [135 lb/100 PSI].
Each curve is based on
B 10 bearing life (2000
Thrust Load
Standard Motor
Straight and Splined Shafts
[lb]
kg
[9000]
4000
[8000]
[7000]
[6000]
[5000]
[4000]
[3000]
3500
3000
2500
2000
1500
[2000]
1000
[1000]
500
0
[inch] [-3] [-2] [-1]
Max. Axial Loads
454 kg [1000 lb]
hours of 12,000,000 shaft
revolutions at 100 RPM)
at rated output torque.
To determine radial load at
speeds other than 100 RPM,
multiply the load values
given on the bearing curve
by the factors in the chart
below.
RPM
Multiplication Factor
50
100
200
300
400
500
600
700
800
1.23
1.00
0.81
0.72
0.66
0.62
0.58
0.56
0.54
C-1-18
0
[1]
[2]
[3]
[4]
[5]
Mounting Surface
Wheel Motor
Tapered Shaf t
[lb]
kg
[9000]
4000
[8000]
[7000]
[6000]
[5000]
[4000]
[3000]
3500
3000
2500
2000
1500
[2000]
1000
[1000]
500
0
For 3,000,000 shaft revolutions or 500 hours–Increase
these shaft loads 52%.
0
mm -80 -60 -40 -20 0 20 40 60 80 100 120
0
mm -80 -60 -40 -20 0 20 40 60 80 100 120
[inch] [-3] [-2] [-1]
0
[1]
[2]
[3]
[4]
[5]
Mounting Surface
2000 Series
Case Pressure and Case
Porting
Char-Lynn 2000 Series
motors are durable and
have long life as long as
the recommended case
pressure is not exceeded.
Allowable case pressure is
highest at low shaft speeds.
Consequently, motor life
will be shortened if case
pressure exceeds these
ratings (acceptability may
vary with application).
Determine if an external
case drain is required from
the case pressure seal
limitation chart.
Case Pressure Seal Limitation
150
[2000]
100
[1500]
Case
Pressure
Bar
50
[PSI]
[1000]
0
Intermittent -Case Drain
Optional
Continuous -Case Drain
Optional
[ 500]
0
0
Case Drain
Required
0
100 200 300 400 500 600 700 800 900
Speed RPM
Case Porting Advantage
Contamination Control —
flushing the motor case.
Cooler Motor — exiting oil
draws motor heat away.
Extend Motor Seal Life —
maintain low case pressure
with a preset restriction in
the case drain line.
C-1
C-1-19
2000 Series
Dimensions
Ports
7/8-14 UNF-2B SAE O-ring Ports (2)
or G 1/2 (BSP) Ports (2)
48,6 [1.91] Max.
17º
6,9/3,8
[.27/.15]
11,9 [.47]
48,6 [1.91] Max.
27,2/25,9
[1.07/1.02]
17º O-ring
7/16-20 UNF-2B SAE
or G 1/4 (BSP)
Case Drain Port
6,9/3,8
[.27/.15]
Port B
Port A
11,9 [.47]
18,1/16,5
[.71/.65]
27,2/25,9
[1.07/1.02]
25,4 [1.00]
7/16-20 UNF-2B SAE O-ring
or G 1/4 (BSP)
Case Drain Port
57,7 [2.27] Max.
56,9 [2.24] Max.
65,02 [2.560]
35,56 [1.400]
Port B —
16,3/15,4
[.64/.61] Dia.
Manifold Mount
Port B
11,58
[.456]
25,4 [1.00]
3/8-16 UNC 15,7
[.62] Deep (3)65,02
or [2.560]
M10 x 1.5 - 6H
(3) [1.400]
35,56
Port B —
22,1 [.870]
16,3/15,4
[.64/.61] Dia.
47,50 [1.870]
1.500]
A
12,1
48] Dia.
23,9
.94]
47,8
1.88] Max.
C-1-20
23,9
[.94]Port B
11,58
[.456]
57,7 [2.27] Max.
B Port
A Port
or G 1/4 (BSP)
Case Drain Port 18,1/16,5
[.71/.65]
56,9 [2.24] Max.
22,1 [.870]
15,8/14,2
47,50 [1.870]
[.62/.56]
7/16-20 UNF-2B
SAE O-ring
Case Drain Port
B Port
56,9 [2.24] Max.
A Port
18,1/16,5
[.71/.65]
56,9 [2.24] Max.
56,6 [2.23] Max.
3/8-16 UNC 15,7
[.62] Deep (3) or
M10 x 1.5 - 6H (3)
38,10 [1.500]
Port A
13,3/12,1
[.52/.48] Dia.
18,1/16,5
[.71/.65]
Port A
or G 1/4 (BSP)
Case Drain Port
56,6 [2.23] Max.
56,9 [2.24] Max.
7/16-20 UNF-2B
SAE O-ring
15,8/14,2
[.62/.56]
Case Drain Port
57,2 [2.25] Max.
6,9/3,8 [.27/.15]
7/16-20 UNF-2B
17º
47,8
[1.88]
Max.
EATON Low Speed High Torque Motors E-MOLO-MC001-E6
60,0 [2.35] Max. September 2011
56,9
[2.24]
Max.
Port A
21,59
[.850]
Port B — Port B 11,58
—
16,3/15,4 16,3/15,4
[.456]
[.64/.61] Dia.
[.64/.61] Dia.
2000 Series
Dimensions
11,58
[.456]
18,1/16,5 18,1/16,5
[.71/.65] [.71/.65]
3/8-16 UNC
3/8-16
15,7 UNC 15,7
[.62] Deep[.62]
(3) orDeep (3) or
M10 x 1.5 M10
- 6H (3)
x 1.5 - 6H (3)
Ports
38,10 [1.500]
38,10 [1.500]
22,1 [.870]22,1 [.870]
47,50 [1.870]
47,50 [1.870]
Port A Port A
13,3/12,1 13,3/12,1
[.52/.48] Dia.
[.52/.48] Dia.
56,6 [2.23]56,6
Max.[2.23] Max.
7/16-20 UNF-2B
7/16-20SAE
UNF-2B
O-ringSAE O-ring
or G 1/4 (BSP)
or G 1/4 (BSP)
Case DrainCase
Port Drain Port
56,9 [2.24]56,9
Max.[2.24] Max.
1-1/16-12 UN-2B SAE O-ring Ports (2)
Positioned 180º Apart
23,9
[.94]
7/8-14 UNF-2B SAE O-ring End Ports (2)
15,8/14,2
B15,8/14,2
Port
[.62/.56] [.62/.56]
A Port A Port
B Port
23,9
[.94]
47,8
47,8
[1.88] Max.[1.88] Max.
Port B
Port B
7/16-20 UNF-2B
7/16-20 UNF-2B
SAE O-ringSAE O-ring 7/16-20 UNF-2B
7/16-20 UNF-2B
Case DrainCase
Port Drain PortSAE O-ringSAE O-ring 47,8
[1.88]
Port Drain Port
56,9 [2.24]56,9
Max.[2.24] Max. Case DrainCase
Max.
47,8 56,9
[1.88][2.24]
Max.Max.
56,9
[2.24]
Max.
Port A
21,59
[.850]
57,2 [2.25]57,2
Max.[2.25] Max.
Max.[2.35] Max.
6,9/3,8 [.27/.15]
6,9/3,8 [.27/.15]60,0 [2.35]60,0
17º
17º
59,0 [2.32]59,0
Max.[2.32] Max.
57,2 [2.25]57,2
Max.[2.25] Max.
Port A
Port A
22,05 [.868]
22,05 [.868]
Port A
21,59
[.850]
C-1
13,34 [.525]
13,34 [.525]
Port B
Port B 50,80
[2.000]
50,80
[2.000]
C-1-21
2000 Series
Dimensions
Ports with Shuttle
7/8 -14 UNF-2B SAE O-ring Ports (2)
11,9 [.47]
Back-Pressure Relief
Port B
Valv e
27,2/25,9
[1.07/1.02]
17,5
[.689]
Port A
25,4 [1.00]
Case Drain
7/16-20 UNF-2B SAE
O-ring Port or
G 1/4 (BSP)
57,7 [2.27] Max.
This port option is available
with shuttle and back
pressure relief valve for
closed loop applications.
62,5 [2.46] Max.
Shuttle Location
48,6 [1.91] Max.
Case Drain
7/16-20 UNF-2B SAE
O-ring Port or
G 1/4 (BSP)
50º
15,9 [.625]
50,80
[2.000]
Min.
7/8
Back-Pressure
Relief Valve
-14 UNF-2B SAE O-ring End Ports (2)
with shuttle and back
pressure relief valve for
closed loop applications.
Case Drain Port
47,8
[1.88]
Max.
62,5
[2.46]
Max.
Port A
Shuttle Location
21,59
[.850]
53,1/47,8
[2.09/1.88]
13,34
[.525]
59,0 [2.32] Max.
22,05 [.868]
C-1-22
Port B
50,80
[2.000]
2000 Series
Note:
For 2000 Series Motors with
a configuration Not Shown
in the charts below: Use
model code number system
on the next page to specify
product in detail.
Product Numbers
Mounting
Shaft
Displ. cm3/ r [in3/ r] / Product Number
Port Size
80
[4.9]
1 Inch Involute
SAE C Splined
1 Inch
SAE 6B Splined
7/8 Inch
SAE B Splined
7/8 -14 O-ring
Staggered
1 1/16 -12 O-ring
180° Apart
7/8 -14 O-ring
Staggered
1 1/16 -12 O-ring
180° Apart
7/8 -14 O-ring
Staggered
1 1/16 -12 O-ring
180° Apart
7/8-14 O-ring
Staggered
7/8 -14 O-ring
Staggered
7/8 -14 O-ring
Staggered
7/8 -14 O-ring
Staggered
32 mm Straight
1 Inch Straight
2 Bolt
SAE A
Flange
1 1/4 Inch Straight
1 1/4 Inch
14 T Splined
1 1/4 Inch Straight
2 Bolt
SAE B
Flange
Standard
with
4 Bolt
Flange
1/4
Use digit prefix —
104-, 105-, or 106- plus four
digit number from charts for
complete product number—
Example 106-1043.
Orders will not be accepted
without three digit prefix.
90*
[5.5]
100
[6.2]
130
[8.0]
160
[9.6]
195
[11.9]
245
[14.9]
305
[18.7]
395
[24.0]
490
[29.8]
104-1001— -1002-1003-1004-1005 -1006-1007 -1143—
104-1037— -1038-1039-1040-1041 -1042-1043 -1044—
104-1022— -1023-1024-1025-1026 -1027-1028 -1228-1420
104-1061— -1062-1063-1064-1065 -1066-1067 -1068-1421
104-1029— -1030-1031-1032-1033 -1034-1035 -1229-1422
104-1087— -1088-1089-1090-1091 -1092-1093 -1094-1423
104-1200— -1201-1202-1203-1204 -1205-1206 -1207—
104-1208— -1209-1210-1211-1212 -1213-1214 -1215—
104-1193
—
-1194
-1195
-1196
-1197
-1198
-1199
—
—
104-1216
—
-1217
-1218
-1219
-1220
—
—
—
—
G 1/2 (BSP))
104-1384
—
-1385
-1386
-1387
-1388
-1389
-1390
-1391
—
1 Inch
14 T Splined
G 1/2 (BSP)
104-1376
—
-1377
-1378
-1379
-1380
-1381
-1382
-1383
—
1
7/8 -14 O-ring
Staggered
1 1/16 -12 O-ring
180° Apart
1/4
1/4
Inch Straight
32 mm Straight
Wheel
Motor
1 1/4 Inch
Tapered
1 1/4 Inch
14 T Splined
Bearingless
C-1
105-——
———— —— —-1148
105-——
———— —— —-1149
G 1/2 (BSP)
105-1134
7/8 -14
O-ring
Staggered
1 1/16 -12 O-ring
180° Apart
7/8 -14 O-ring
Staggered
1 1/16 -12 O-ring
180° Apart
7/8 -14 O-ring
Staggered
-1135
-1136
-1137
-1138
-1139
-1140
-1141
—
105-1001— -1002-1003-1004-1005 -1006-1007 -1060-1152
105-1071
—
-1072
-1073
-1074
-1075 -1076
-1077
-1078
—
105-1029— -1030-1031-1032-1033 -1034-1035 -1096—
105-1079— -1080-1081-1082-1083 -1084-1085 -1086—
106-1008— -1009-1010-1011-1012 -1013-1014 -1015-1047
G 1/2 (BSP)
106-1038
—
-1039
-1040
-1041
-1042
-1043
*New Release
-1044
-1045
—
106-1044
Motors with Corrosion Protection
Mounting
Shaft
Port Size
80
[4.9]
2 Bolt
SAE A
Flange
Staggered
1 inch Straight
1 1/4 Inch Straight
7/8 -14 O-ring
Staggered 104-1528
7/8 -14 O-ring
104-1516
90*
[5.5]
100
[6.2]
130
[8.0]
160
[9.6]
195
[11.9]
245
[14.9]
305
[18.7]
395
[24.0]
490
[29.8]
—
-1529
-1530
-1531
-1532
-1533
-1534
-1519
-1535
—
-1536
-1537
-1538
-1539
-1452
-1479
-1509
-1489
*New Release
C-1-23
2000 Series
The following 30-digit coding system has been developed to identify all of the configuration options for the 2000 Series motor. Use this model code to specify a motor with the
desired features. All 30 digits of the code must be present when ordering. You may want to
photocopy the matrix below to ensure that each number is entered in the correct box.
Model Code
M
0 2
* *
* *
* *
* *
* *
1
2 3
4 5 6
7 8
9 10
11 12
13 14
1 Product
M – 2000 Series Motor
2 , 3 Product Series
02 – 2000 Series Motor
4 , 5 , 6 Displacement
cm3/r [in3/r]
049 – 80.6 cm3/r [4.92]
055 – 90.6 cm3/r [5.53 in3/r]
062 – 101.6 cm3/r [6.20 in3/r]
080 – 130.6 cm3/r [7.97 in3/r]
096 – 158.1 cm3/r [9.65 in3/r]
119 – 194.8 cm3/r [11.89 in3/r]
149 – 244.3 cm3/r [14.91 in3/r]
187 – 306.6 cm3/r [18.71 in3/r]
240 – 393.8 cm3/r [24.03 in3/r
298 – 489.0 cm3/r [29.84 in3/r]
7 , 8 Mounting Type
AB – Wheel, 4 Bolt: 108.0
[4.25] Pilot Dia. 13.59 [.535]
Dia. Holes on 147.6 [5.81] Dia.
Bolt Circle. 127.0 [5.00] Dia.
Rear Mount Pilot
AC – Standard, 2 Bolt: 82.6
[3.25] Pilot Dia. 13.59 [.535]
Dia. Holes on 106.4 [4.19]
Dia. Bolt Circle. SAE A
AD – Bearingless (w/ Leakage
Slots), 4 Bolt: 101.6 [4.00] Pilot
Dia. 13.59 [.535] Dia. Holes on
127.0 [5.00] Dia. Bolt Circle
AF – Standard, 2 Bolt: 101.6
[4.00] Pilot Dia. 14.35 [.565]
Dia. Holes on 146.0 [5.75] Dia.
Bolt Circle. SAE B
AH – Standard, 4 Bolt: 82.6
[3.25] Pilot Dia. 13.59 [.535]
Dia. Holes on 106.4 [4.19]
Dia. Bolt Circle
AJ – Standard (Magneto),
4 Bolt: 82.6 [3.25] Pilot Dia.
13.59 [.535] Dia. Holes on
106.4 [4.19] Dia. Bolt Circle.
2.79 [.110] Pilot Length
AL - Wheel (European), 4 Bolt:
125 [4.92] Pilot Dia. 13.79
[.543] Dia. Holes on 159.99
[6.299] Dia. Bolt Circle
AP – Wheel, 4 Bolt: 108.0
[4.25] Pilot Dia. 13.59 [.535]
Dia. Holes on 147.6 [5.81]
Dia. Bolt Circle. 127.0 [5.00]
Dia. Rear Mount Pilot. Spigot
Reduced to 88.9 [3.50] Dia. by
25.4 [1.00] Depth.
AZ – Bearingless (w/ Leakage
Slots), 4 Bolt: 100.0 [3.94]
Pilot Dia. 11.0 [.43] Dia. Holes
on 125.0 [4.92] Dia Bolt Circle
(European)
C-1-24
9 , 10 Output Shaft
*
* *
15 16 17
00 – None (Bearingless)
01 – 25.40 [1.000] Dia.
Straight Shaft with 1/420UNC-2B Thread in End, 6.35
[.250] Wide x 25.40 [1.000]
Dia. Woodruff Key
02 – 31.75 [1.250] Dia.
Straight Shaft with .37516UNC-2B Thread in End,
7.938 [.3125] Sq x 31.75
[1.250] Straight Key
03 – 31.75 [1.250] Dia. .125:1
Tapered Shaft per SAE J501
with/1.000-20 UNEF-2A
Threaded Shaft End and
Slotted Hex Nut, 7.938 [.3125]
Sq x 25.40 [1.0] Straight Key
04 – 31.75 [1.250] Dia. Flat
Root Side Fit, 14 Tooth, 12/24
DP 30° Involute Spline w/
.375-16UNC-2B Thread in End,
33.0 [1.30] Min. Full Spline
Length
05 – 25.40 [1.000] Dia. 6B
Spline per SAE J499 with
.250-20UNC-2B Thread in End,
22.76 [.896] Min. Full Spline
Length
07 – 22.22 [.875] Dia. Flat Root
Side Fit, 13 Tooth, 16/32 DP
30° SAE B Involute Spline, 15.2
[.60] Min. Full Spline Length
16 – 32.00 [1.260] Dia.
Straight Shaft with M8 x
1.25-6H Thread in End, 9.982
[.3930] W x 7.995 [.3132] H x
45.00 [1.772] L Key
17 – 31.75 [1.250] Dia. Straight
Shaft With 3/8 -16 UNC-2B
Thread in End, 7.938 [.3125]
Sq x 31.75 [1.250] Straight Key,
Corrosion Resistant (Seal area
to shaft end)
18 – 31.75 [1.250] Dia. .125:1
Tapered Shaft per SAE
J501 with 1.000-20UNEF2A Threaded Shaft End and
Slotted Hex Nut, 7.938 [.3125]
Sq x 25.40 [1.000] Straight Key,
Corrosion Resistant (Under
seal area only)
19 – 25.00 [.984] Dia. Straight
Shaft with M8 x 1.25-6h Thread
in End, 7.982 [.3142]W x 6.954
[.2738]H x 31.82 [1.254]L Key
28 – 32.00 [1.260] Dia. 10:1
Tapered Shaft Per ISO R775
with M10 X 1.50-6H Thread in
End, 6.00 [.236] Sq. x 50.00
[1.968] Key
1
*
* *
0 0
* *
* *
A A
F
18 19
20 21
22 23
24 25
26 27
28 29
30
European Spline
41 – 35.00 [1.378] Dia. 10:1
Tapered Shaft Per ISO R775
with M20 x 1.5-6g Threaded
Shaft End and Slotted Hex Nut,
6.00 [.236] Sq. X 20.00 [.787]
Key
42 – 35.00 [1.378] Dia. Straight
Shaft with M8 x 1.25-6h Thread
in End, 9.982 [.3930]W x 7.995
[.3132]H x 45.00 [1.772]L Key
11 , 12 Ports
AA – .875-14 UNF-2B SAE
O-ring Ports - Staggered
Ports
AB –12.70 [.500] and 15.88
[.625] Dia. Manifold Ports with
3 x .375-16 UNC-2B Port Block
Mounting Holes
AC –.875-14 UNF-2B SAE
O-ring Ports - Ports Oriented
180° to each other
AE – 12.70 [.500] And 15.88
[.625] Dia. Manifold Ports with
3 x M10 x 1.5-6H Port Block
Mounting Holes
AF – 1.0625-12 UN-2B SAE
O-ring Ports - Ports Oriented
180° to each other
AG – G-1/2 BSP Straight THD
Ports - Staggered Ports
AN – G-1/2 BSP Straight THD
Ports - End Ported
AR – .875-14 UNF-2B SAE
O-ring Ports - End Ported, Cast
Boss Removed
AS – G-1/2 Bsp Straight THD
Ports - Staggered Port with
2 x M10 x 1.5-6H Port Block
Mounting Holes - European
13 , 14 Case Flow Options
Shuttles available with
port code AA only)
01 – .4375-20 UNF-2B SAE
O-Ring Port
02 – G 1/4 BSP Straight THD
Port
09 – Reverse Flow Shuttle
Valve w/ G-1/4 BSP Straight
THD Port, .062 Dia. Shuttle
Flow Orifice
Valve w/ .4375-20 UNF-2B SAE
O-Ring Port, .062 Dia. Shuttle
Flow Orifice
15 Low Pressure Relief
0 – None
A – Set at 4.5 bar [65 lbf/in2]
B – Set at 15.2 bar [220 lbf/in2]
C – Set at 20.7 bar [300 lbf/in2]
E – Set at 11.03 bar [160 lbf/in2]
16 , 17 Pressure/Flow Option
Integral Cross-Over Relief Valve:
00 – None
30 – Set at 103.4 bar [1500 lbf/in2]
31 – Set at 120.6 bar [1750 lbf/in2]
32 – Set at 137.9 bar [2000 lbf/in2]
33 – Set at 155.1 bar [2250 lbf/in2]
34 – Set at 172.4 bar [2500 lbf/in2]
35 – Set at 189.6 bar [2750 lbf/in2]
36 – Set at 206.8 bar [3000 lbf/in2]
18 Geroler Option
1 – Standard
19 Seal Options
0
1
2
4
– Standard
– Viton
– Viton Shaft Seal
– Seal Guard
20 , 21 Accessories
00 – None
AD – M 12 Threaded
Connector, Digital Speed
Pickup (30 Pulse)
AE – M 12 Threaded
Connector, Long Body Digital
Speed and Direction Pickup
(1 = Power Supply, Pin 2
= Output Signal 1, Pin 3 =
Common, Pin 4 = Output
Signal 2)
22 , 23 Special Features
(Hardware)
00 – None
24 , 25 Special Features (Assembly)
00 – None
AB – Reverse Rotation
AE - Flange Rotated 45
Degrees
26 , 27 Paint/Packaging
AA – No Paint, Indiv. Box
AB – Low Gloss Black Primer,
Indiv. Box
28 , 29 Customer ID
AA – None
30 Design Code
F – Sixth
Feature in bold are preferred and allow for shorter lead time
Description
the spring force returns
the spool valve to LSHT
position. Pilot pressure may
come from any source that
will provide uninterrupted
pressure during the high
speed mode operation. Pilot
pressure 6,9 D Bar [100 D
PSI] minimum, up to the full
operating pressure of the
motor.
In normal LSHT operation
the Char-Lynn two speed
motor will function with
equal shaft output in either
direction (CW or CCW), the
same as the single speed
Char-Lynn disc valve motors.
However, to prevent
cavitation in the HSLT mode,
the preferred direction of
shaft rotation is counter
clockwise (port B pressurized). This unique disc valve
is not symmetrical in porting
the fluid for the HSLT mode.
Consequently, when the
pressure is reversed for
HSLT CW rotation, cavitation
can occur. Installing a
restriction (200 psi or
more depending on flow)
in the hydraulic line that
connects port B will prevent
cavitation.
If you are operating in a
critical area and a restriction
in the hydraulic line causes
concern, these two speed
motors can be ordered
timed with CW preferred
HSLT shaft rotation. Hence,
with this option port B will
have to be pressurized for
CW preferred HSLT shaft
rotation. The restriction
recommended for the line
connecting port B remains
unchanged.
Finally in closed circuit
C-1
applications a hydraulic line
restriction is not required.
Instead, the charge pump
can be used to supply
and maintain a minimum
pressure of 14 Bar [200 PSI].
The Eaton 2000 Series
motors are available with an
integral two speed feature
that changes the displacement in a ratio of 1 to 2 and
shifts the motor from a low
speed high torque (LSHT)
mode to a high speed low
torque (HSLT) mode. The
open center selector valve
shifts the speed mode from
low to high speed when
pilot pressure of 6.9 D Bar
[100 D PSI] minimum is
applied to the pilot port (6.9
Bar [100 PSI] higher than
case pressure). In the high
speed mode torque values
are approximately one half
with twice the speed of the
conventional 2000 Series
single speed motors.
An external two position
three way valve is required
for shifting the pilot pressure
port between signal
pressure (HSLT) and low
pressure (LSHT)
Two speed motors are
available with a return line
closed center shuttle for
closed circuit applications.
Low speed high torque
mode is the normal position
of the speed selector valve.
When a differential pressure
is supplied to the pilot port
and 6,9 Bar [100 PSI] is
reached, the selector valve
overcomes the return spring
force and the spool shifts to
the high speed mode. The oil
in the opposite side of the
spool is drained internally.
Pressure between the
pilot supply and case drain
or return line (depending
on open or closed circuit
system) must be maintained
to keep the motor in the
high speed mode.
When pilot pressure is
removed from the pilot port
the pressure in the pilot
end of the spool valve is
relieved and drained back
through this three way valve,
Performance
Data
In the high speed mode
torque values are approximately one half with
twice the speed of the conventional 2000 Series single
speed motors.
In the low speed mode
torque and speed values
are the same as the conventional 2000 Series
motors.
Be certain in closed loop
applications that the
charge pump when used
for back pressure on the
B port, has sufficient displacement to maintain
charge pressure especially
in dynamic braking
or overrunning load
conditions.
Note:
Low displacement (4.9 to
8.0 CID) motors have limited
starting torque when started
in high speed mode.
Due to potential problems
in maintaining charge
pump pressure at port
B for uninterrupted back
pressure during dynamic
braking, Eaton does not
recommend the two speed
motor where overrunning
conditions may exist.
Important!
C-1-25
Note:
This is the low speed biased motor circuit. For the high
speed biased motor motor circuit please contact your Eaton
Hydraulics representative.
Typical Hydraulic Circuit
Pump Pressure and Return, and
Shaft Rotation Directional Control
Check Valve s
Valv e
Pilot Pressure 6,9 Bar [100 PSI] Min.
Two Position Three Way Valv e
LSHT
HS LT
Pilot Port
Port A
Pilot Port
Port B
Port A
Port B
Restriction 14 Bar [200 PSI]
and Check Valv e
Case Drain
(Option)
2000 Series
Motor —
Two Spee d
Output
Shaft
Two Spee d
Motor
Schematic
Optional Shuttle
Valve Locatio n
Case Drain
Case Drain (Option)
Case Drain
Pilot Port
Port A
Port B
Case Drain
(Option)
Maximum System
Horsepower Curve
Torqu e
Low Speed
High Torque
Two Spee d
Motor
Schematic
with...
High Speed
Low Torqu e
Output
Shaft
...Optional Two
Way Shuttle Valv e
Case Drain
Speed - RPM
2 - Speed Operating Range
C-1-26
Specifications
Specification Data — 2000 Series Two-Speed Motors
Displ. cm 3/r [in 3 /r]
Max. Speed
(RPM)
@ Continuous Flow
Flow l/min [GPM]
High Speed Mode 40 [2.45] 50 [3.1] 65 [4.0] 80 [4.8] 95 [5.95]
Low Speed Mode 80 [4.9] 100 [6.2] 130 [8.0] 160 [9.6] 195 [11.9]
High Speed Mode 1000
1000
990
860
700
Low Speed Mode
500500495430350
High Speed Mode 45 [12]
55 [15]
Low Speed Mode 45 [12]
55 [15]
Torque*
High Speed Mode
Nm
Continuous
100 [880] 125 [1115]
[lb-in]
Intermittent
145 [1300] 185 [1660]
Torque*
Low Speed Mode
Nm
Continuous
235 [2065] 295 [2630]
[lb-in]
Intermittent
345 [3035] 445 [3950]
Pressure
Continuous205 [3000] 205 [3000]
∆ bar [∆ PSI]
Intermittent
310 [4500] 310 [4500]
Weight
Standard or
13,8 [30.5] 14,1 [31.0]
kg [lb]
Wheel Mount
Bearingless
11.8 [26.0] 12,0 [26.5]
70 [19]
70 [19]
75 [20]
75 [20]
75 [20]
75 [20]
120 [7.45]
245 [14.9]
560
280
155 [9.35] 195 [12.0] 245 [14.9]
305 [18.7] 395 [24.0] 490 [29.8]
450
350
230
225 175115
75 [20]
75 [20]
75 [20]
75 [20]
75 [20]
75 [20]
75 [20]
75 [20]
165 [1450] 195 [1725] 240 [2150] 300 [2675] 380 [3350] 365 [3225] 448 [3970]
240 [2150] 240 [2150] 300 [2650] 375 [3330] 440 [3900] 445 [3940] 486 [4300]
385 [3420] 455 [4040] 540 [4780]
560 [4970] 570 [5040] 665 [5890]
205 [3000] 205 [3000] 205 [3000]
310 [4500] 260 [3750] 260 [3750]
14,3 [31.5] 14,5 [32.0] 15,0 [33.0]
660 [5850]
820 [7250]
205 [3000]
260 [3750]
15,4 [34.0]
765 [6750]
885 [7820]
205 [3000]
240 [3500]
15,9 [35.0]
775 [6840] 845 [7470]
925 [8170] 930 [8225]
155 [2250] 120 [1750]
190 [2750] 140 [2000]
16,3 [36.0] 16,8 [37.0]
12,2 [27.0] 12,5 [27.5] 12.9 [28.5] 13,4 [29.5] 13,8 [30.5] 14,3 [31.5] 14,7 [32.5]
Note:
load applications.
High Speed Mode
(Reduced Motor
Displacement)
Low Speed Mode
(Full Motor Displacement)
310 bar [4500 PSI]
∆ bar [∆ PSI] :
outlet port
Continuous Rating:
10% of every minute
Peak Operation:
1% of every minute
Recommended Fluids:
Recommended System
Operating Temp.:
-34°C to 82°C [-30°F to
180°F]
4406: 20/18/13
C-1-27
C-1
Dimensions
Standard and Wheel
Port B
Y Max.
X
Two-Speed Wheel Motors
Y Max.
X
C-1-28
7/16 -20 UNF-2B SAE O-ring Pilot Control Port (1)
G 1/4 (BSP) Pilot Control Port (1)
Two-Speed Standard Motors
Port B
Ports
Standard Mount Motor DImensions
Displacement
cm 3/r [in 3/r]
X
mm [inch]
Y
mm [inch]
80 [4.9]
100 [6.2]
130 [8.0]
160 [9.6]
195 [11.9]
245 [14.9]
305 [18.7]
395 [24.0]
490 [29.8]
137,4 [5.41]
142,0 [5.59]
148,5 [5.85]
148,5 [5.85]
155,2 [6.11]
164,2 [6.47]
175,7 [6.92]
191,5 [7.54]
209,0 [8.23]
231,6 [9.12]
236,5 [9.31]
242,9 [9.56]
242,9 [9.56]
249,4 [9.82]
258,6 [10.18]
270,1 [10.63]
286,1 [11.26]
303,3 [11.94]
Wheel Mount Motor DImensions
Displacement
cm 3/r [in 3/r]
X
mm [inch]
Y
mm [inch]
80 [4.9]
100 [6.2]
130 [8.0]
160 [9.6]
195 [11.9
245 [14.9]
305 [18.7]
395 [24.0]
490 [29.8]
97,2 [3.83]
101,8 [4.01]
108,3 [4.27]
108,3 [4.27]
115,0 [4.53]
124,2 [4.89]
135,5 [5.34]
151,4 [5.96]
168,9 [6.65]
191,5 [7.54]
196,4 [7.73]
202,7 [7.98]
202,7 [7.98]
209,3 [8.24]
218,5 [8.60]
229,9 [9.05]
245,9 [9.68]
263,1 [10.36]
or
Ports
7/16 -20 UNF-2B SAE O-ring Pilot Control Port (1)
Dimensions
Bearingless
or
G 1/4 (BSP) Pilot Control Port (1)
Two-Speed
Bearingless Motors
41,7/40,8
[1.64/1.61]
17,3/15,7
[.68/.62]
61,9/60,8
[2.44/2.39]
27,7/26,1
[1.09/1.03]
14,0/12,9
[.55/.51]
31,0/30,2
[1.22/1.19]
3/8-24 UNF
15,8[.62] Dp. (4)
8,7/7,8
[.34/.31]
20,6/19,5
[.81/.77]
24,2/23,3
[.95/.92]
26,5/25,4
[1.04/1.00]
7/16-20 UNF-2B O-ring Port — Pilot Control
Pilot Port Pressurized 6,9 D Bar [100 D PSI]
High Speed Low Torque (HSLT)
Pilot Port Depressurized (Tank)
Low Speed High Torque (LSHT)
Port A
Port B
37,9/36,8
[1.49/1.45]
Optional
Case Drain
10,7/9,6
[.42/.38]
64,3/62,7
[2.53/2.47]
66,1/65,0
[2.60/2.56]
Port B
3,1 [.12] Max.
122,0 [4.80] Max.
68,1
[2.68] Max.
X
C-1
45,5/44,4
[1.79/1.75]
Y Max.
74,0/72,8
[2.91/2.87]
63,0
[2.48]
Max.
6,4/5,8
[.25/.23]
Displacement
cm 3/r [in 3/r]
X
mm [inch]
Y
mm [inch]
80 [4.9]
100 [6.2]
130 [8.0]
160 [9.6]
195 [11.9]
245 [14.9]
305 [18.7]
395 [24.0]
490 [29.8]
79,3 [3.13]
84,1 [3.31]
90,7 [3.57]
90,7 [3.57]
97,3 [3.83]
106,4 [4.19]
117,8 [4.64]
133,6 [5.26]
151,1 [5.95]
174,0 [6.85]
178,9 [7.04]
185,2 [7.29]
185,2 [7.29]
191,8 [7.55]
201,0 [7.91]
212,4 [8.36]
228,4 [8.99]
245,6 [9.67]
9/16-18
UNF O-ring
Case Drain
Port
46,0/44,9
[1.81/1.77]
C-1-29
Note:
in the charts below, contact
your Eaton Representative.
Product Numbers
Mounting Shaft
2 Bolt
SAE A
Flange
1 Inch Straight
1 1/4 Inch Straight
1 1/4 Inch
14 T Splined
Wheel
Motor
Bearingless
1 1/4 Inch Tapered
1 1/4 Inch
14 T Splined
Port Size
7/8 -14
O-ring
Staggered
7/8 -14 O-ring
Staggered
7/8 -14 O-ring
Staggered
7/8 -14 O-ring
Staggered
7/8 -14 O-ring
Staggered
7/8 -14 O-ring
Staggered
193- plus four digit number
from charts for complete
product number—Example
193-0002.
80
[4.9]
100
[6.2]
130
[8.0]
160
[9.6]
195
[11.9]
245
[14.9]
305
[18.7]
395
[24.0]
490
[29.8]
193-0002-001
-0003
-0004
-0005
-0006
-0007
-0008
-0009
—
193-0010-001
-0011
-0012
-0013
-0014
-0015
-0016
-0017
-0070
193-0018-001
-0019
-0020
-0021
-0022
-0023
-0024
-0025
—
193-0222-001
-0223
-0224
-0225
-0226
-0227
-0228
-0229
—
193-0230-001
-0231
-0232
-0233
-0234
-0235
-0236
-0237
—
193-0282-001
-0283
-0234
-0285
-0286
-0287
-0288
-0289
—
193-0288-001
C-1-30
2000 Series
Two-Speed
The following 30-digit coding system has been developed to identify all of the configuration options for the 2000 Series motor. Use this model code to specify a motor with the
Model Code (193-)
M
2 2
* *
* *
* *
* *
* *
1
2 3
4 5 6
7 8
9 10
11 12
13 14
1 Product
M – Motor
2 , 3 Series
22 – 2000 2 Speed Series
(1:2 Ratio)
049 – 80.6 cm3/r [4.92 in3/r]
062 – 101.6 cm3/r [6.20 in3/r]
080 – 130.6 cm3/r [7.97 in3/r]
096 – 158.1 cm3/r [9.65 in3/r]
119 – 194.8 cm3/r [11.89 in3/r]
149 – 244.3 cm3/r [14.91 in3/r]
187 – 306.6 cm3/r [18.71 in3/r]
240 – 393.8 cm3/r [24.03 in3/r
298 – 489.0 cm3/r [29.84
in3/r]
7 , 8 Mounting
Description
AB – Wheel, 4 Bolt: 108.0
[4.25] Pilot Dia. 13.59 [.535]
Dia. Holes on 147.6 [5.81]
Dia. Bolt Circle. 127.0 [5.00]
Dia. Rear Mount Pilot
[3.25] Pilot Dia. 13.59 [.535]
Dia. Holes on 106.4 [4.19]
Dia. Bolt Circle. SAE A
AE – Bearingless (w/
Leakage Slots), 4 Bolt: 101.6
[4.00] Pilot Dia. 13.59 [.535]
Dia. Holes on 127.0 [5.00]
Dia. Bolt Circle
AF – Standard, 2 Bolt: 101.6
[4.00] Pilot Dia. 14.35 [.565]
Dia. Holes on 146.0 [5.75]
Dia. Bolt Circle. SAE B
Dia Bolt Circle (European)
9 , 10 Output Shaft
Description
*
* *
15 16 17
01 – 25.40 [1.000] Dia.
Straight Shaft with 1/420UNC-2B Thread in End,
6.35 [.250] Wide x 25.40
[1.000] Dia. Woodruff Key
02 – 31.75 [1.250] Dia.
Straight Shaft with .37516UNC-2B Thread in End,
7.938 [.3125] Sq x 31.75
03 – 31.75 [1.250] Dia.
.125:1 Tapered Shaft per
SAE J501 with/1.000-20
UNEF-2A Threaded Shaft
End and Slotted Hex Nut,
7.938 [.3125] Sq x 25.40 [1.0]
Straight Key
04 – 31.75 [1.250] Dia. Flat
DP 30° Involute Spline w/
.375-16UNC-2B Thread in
End, 33.0 [1.30] Min. Full
Spline
11 , 12 Ports Description
AA – .875-14 UNF-2B SAE
Ports
AB –12.70 [.500] and 15.88
[.625] Dia. Manifold Ports
with 3 x .375-16 UNC-2B
Port Block Mounting Holes
/ Selector Valve
01 – .5625-10 UNF-2B SAE
O-Ring Case Drain Port,
.4375-20 UNF-2B SAE
O-Ring Pilot Control Port,
Optional .4375-20 UNF-2B
SAE Case Drain Port for Pilot
Operated Normally Low
Speed
1
*
* *
0 0
* *
* *
A A
A
18 19
20 21
22 23
24 25
26 27
28 29
30
15 Shuttle Valve / Low
Pressure Relief
0 – NONE
16 , 17 Pressure / Flow
Option
00 – NONE
18 Geroler Option
1 – STANDARD
19 Seal Option
0 – STANDARD
C-1
20 , 21 Accessories
00 – NONE
(Hardware)
00 – NONE
(Assembly)
00 – NONE
26 , 27 Paint / Packaging
AA – No Paint, Individual Box
AB – Low Gloss Black
Primer, Individual Box
28 , 29 Customer
Identification
AA – NONE
30 Design Code
A – FIRST
C-1-31
4000 Compact Series
Port B
Features
Port A
• Shuttle Valve with BackPressure Relief Valve
Highlights
• Speed Sensors
• End Ports.
Geroler ® Star
Benefits
• Higher bearing capacity
than 2000 Series
• Torque of 4000 Series
Applications
• Skid Steer Loaders
• Fairway Mowers
• Harvesters
D isc Valve
Motor Shaft Drive
and Valve Driv e
• Vehicles where space
may be at a premium.
Motor Shaft
and Bearings
Description
This new compact addition in a family of disc valve hydraulic
motors produces the same amount of torque as the current
4000 Series. Yet, it is housed in an envelope similar to its
smaller counterpart, the 2000 Series. The unit’s intermittent
torque rating is 1220 Nm [10800 lb-in]. A variety of mounting
options include two 2 bolt mounts (SAE A, SAE B), and four
4 bolt mounts (magneto, standard and wheel mounts.) For
added flexibility, the motor can be specified with either the
larger size shafts of the 2000 Series of standard output shaft
sizes of the 4000 Series, plus one new 1-1/2 inch straight
(the small envelope and optional shaft sizes make this motor
ideal for vehicles like skid-steer loaders whose hallmark is
high power and productivity in a small frame.)
C-2
Specifications
Geroler Element
Flow l/min [GPM]
Speed RPM
Pressure bar [PSI]
Torque Nm [lb-in]
6 Displacements
464 Cont.**
699 Inter.*
200 [3000] Cont.**
300 [4500] Inter.*
975 [8627] Cont.**
1218 [10788] Inter.*
**Continuous— (Cont.) Continuous rating, motor may be run continuously at these ratings.
Lawn and Turf
Skid Steer
Boom Lift
Harvestor
C-2-1
4000 Compact Series
Specifications
Specification Data — 4000 compact Series Motors
Max. Speed (RPM) Continuous
@ Flow
Intermittent
Flow
Continuous
l/min [GPM]
Intermittent
Torque*
Continuous
Nm [lb-in]
Intermittent
Pressure
Continuous
∆ bar
Intermittent
[∆ PSI]
Peak
Weight
Standard or
kg [lb]
Wheel Mount
Bearingless
160 [9.8]
464
699
75 [20]
115 [30]
510 [4514]
690 [6108]
225 [3000]
310 [4500]
310 [4500]
10,4 [23.0]
200 [12.3]
375
562
75 [20]
115 [30]
758 [5715]
840 [7436]
225 [3000]
295 [4250]
310 [4500]
10,9 [24.0]
250 [15.4]
300
450
75 [20]
115 [30]
734 [6500]
935 [8272]
205 [3000]
260 [3750]
310 [4500]
11,3 [25.0]
325 [19.8]
234
351
75 [20]
115 [30]
793 [7021]
1053 [9320]
170 [2500]
240 [3500]
310 [4500]
11,8 [26.0]
405 [24.6]
188
282
75 [20]
115 [30]
800 [7079]
921 [8153]
140 [2000]
170 [2500]
275 [4000]
12,2 [27.0]
490 [29.8]
155
232
75 [20]
115 [30]
975 [8627]
1218 [10778]
140 [2000]
171 [2500]
260 [3750]
12,2 [27.0]
8,4 [18.5]
8,8 [19.5]
9,3 [20.5]
9,8 [21.5]
10,2 [22.5]
10,2 [22.5]
Note:
load applications.
310 bar [4500 PSI]
∆ bar [∆ PSI] :
outlet port
Continuous Rating:
10% of every minute
Peak Operation:
1% of every minute
C-2-2
Recommended Fluids:
Recommended System
Operating Temp.:
-34°C to 82°C [-30°F to
180°F]
4406: 20/18/13
4000 Compact Series
Performance Data
160 cm3/r [9.8 in3/r]
in production.
[0.25]
0,95
[0.5]
1,9
[1]
3,8
[2]
7,5
[4]
15
[6]
Continuous
23
[8]
Peak
No Operation
Flow LPM [GPM]
Intermittent
30
[10]
38
[12]
45
[14]
53
[16]
61
[18]
68
[20]
76
[22]
83
[24]
91
[25]
95
[30]
114
[250]
15
[500]
35
[750] [1000] [1250] [1500] [1750] [2000] [2250] [2500] [2750] [3000] [3250] [3500] [3750] [4000] [4250] [4500]
50
70
85
105
120
140
155
170
190
205
225
240
260
275
295
310
244
28
4
274
31
10
274
31
22
301
34
40
305
34
87
293
33
133
280
32
181
259
29
228
238
27
275
210
24
322
182
21
370
143
16
417
105
12
464
543
61
3
554
63
8
593
67
21
623
70
39
662
75
85
659
74
131
656
74
179
630
71
225
604
68
272
577
65
319
550
62
367
514
58
414
478
54
461
433
49
508
387
44
556
363
41
580
244
28
699
854
96
7
899
102
20
940
106
38
1004
113
83
1003
113
129
1002
113
177
978
110
223
954
108
269
923
104
316
893
101
363
853
96
410
814
92
457
762
86
504
711
80
552
683
77
576
546
62
695
1210
137
19
1261
143
36
1354
153
81
1357
153
127
1360
154
175
1348
152
220
1336
151
266
1308
148
313
1280
145
360
1247
141
406
1213
137
453
1167
132
500
1121
127
548
1095
124
572
967
109
692
1513
171
17
1579
178
35
1699
192
79
1705
193
124
1711
193
172
1701
192
217
1692
191
262
1665
188
308
1638
185
356
1601
181
401
1564
177
448
1518
172
495
1472
166
542
1445
163
566
1308
148
685
1816
205
14
1898
214
33
2046
231
77
2056
232
121
2066
233
169
2061
233
213
2056
232
258
2034
230
304
2012
227
351
1973
223
397
1935
219
442
1893
214
489
1851
209
537
1824
206
560
1689
191
678
2092
236
12
2197
248
31
2386
270
74
2399
271
118
2412
273
166
2408
272
209
2403
272
253
2385
269
298
2367
267
345
2329
263
390
2291
259
435
2252
254
482
2212
250
529
2184
247
552
2045
231
669
[2777]
3 14
648
2361
267
10
2492
282
28
2725
308
72
2741
310
114
2758
312
162
2755
311
204
2752
311
247
2739
310
293
2727
308
339
2692
304
383
2658
300
428
2623
296
474
2589
292
521
2561
289
544
2421
274
660
}
2621
296
9
2766
313
24
3049
344
67
3074
347
109
3100
350
157
3102
351
199
3105
351
241
3092
349
286
3080
348
332
3045
344
375
3010
340
418
2973
336
465
2937
332
513
2910
329
535
2777
314
648
2874
325
7
3033
343
20
3368
381
63
3405
385
104
3442
389
152
3450
390
193
3458
391
235
3447
390
279
3436
388
324
3401
384
366
3366
380
409
3328
376
456
3291
372
504
3266
369
526
3144
355
637
3088
349
6
3270
369
17
3693
417
59
3751
424
99
3809
430
145
3806
430
186
3802
430
229
3796
429
272
3789
428
317
3756
424
358
3724
421
400
3682
416
446
3641
411
493
3496
395
14
4016
454
55
4098
463
93
4180
472
139
4163
470
179
4146
468
223
4144
468
265
4143
468
309
4114
465
350
4085
462
390
4040
456
436
3995
451
483
3761
425
10
4319
488
49
4417
499
87
4514
510
133
4500
508
172
4485
507
214
4487
507
256
4489
507
301
4022
454
6
4618
522
44
4732
535
80
4846
548
127
4835
546
165
4824
545
205
4830
546
247
4836
546
292
4828
545
35
5023
568
71
5218
590
120
5191
586
157
5163
583
197
5022
567
27
5308
600
63
5593
632
113
5547
627
150
5501
622
189
5856
662
104
5784
653
141
C-2
Torque [lb-in]
Nm
Speed RPM
6108
690
96
C-2-3
4000 Compact
Series
200 cm3/r [12.3 in3/r]
Performance Data
in production.
[0.25]
0,95
[0.5]
1,9
[1]
3,8
[2]
7,5
[4]
15
[6]
Continuous
23
[8]
Peak
No Operation
Flow LPM [GPM]
Intermittent
30
[10]
38
[12]
45
[14]
53
[16]
61
[18]
68
[20]
76
[22]
83
[24]
91
[25]
95
[30]
114
[250]
15
[500]
35
[750] [1000] [1250] [1500] [1750] [2000] [2250] [2500] [2750] [3000] [3250] [3500] [3750] [4000] [4250]
50
70
85
105
120
140
155
170
190
205
225
240
260
275
295
115
13
4
268
30
8
306
35
17
402
45
35
403
46
72
385
44
109
368
42
147
353
40
185
339
38
223
282
32
261
224
25
299
200
23
337
176
20
375
504
57
3
584
66
7
721
81
16
841
95
34
896
101
70
863
98
107
831
94
146
822
93
184
813
92
222
762
86
260
712
80
298
667
75
336
623
70
374
565
64
412
507
57
449
465
53
468
259
29
562
963 1274
109
144
4
3
1104 1516 1913 2243 2397 2772
125
171
216
253
271
313
14
13
12
10
9
6
1218 1647 2107 2478 2826 3238 3954 4451 4755
138
186
238
280
319
366
447
503
537
32
31
30
28
27
24
29
26
23
1361 1780 2247 2649 3068 3513 3947 4367 4710
154
201
254
299
347
397
446
493
532
69
68
66
65
62
60
56
53
50
1354 1785 2260 2657 3087 3547 3965 4389 4793
153
202
255
300
349
401
448
496
542
106
104
102
100
97
93
90
86
81
1347 1790 2273 2665 3106 3581 3982 4411 4876
152
202
257
301
351
405
450
498
551
144
142
140
137
134
130
127
122
117
1319 1774 2212 2642 3086 3556 3974 4410 4839
149
200
250
299
349
402
449
498
547
181
179
177
174
170
165
161
156
151
1291 1758 2151 2620 3067 3530 3965 4408 4802
146
199
243
296
346
399
448
498
543
219
217
214
211
207
202
197
192
186
1237 1693 2121 2601 2968 3504 3953 4368 4832
140
191
240
294
335
396
447
493
546
257
255
252
248
244
238
233
227
221
1183 1629 2091 2581 2870 3477 3940 4328 4861
134
184
236
292
324
393
445
489
549
296
293
290
286
282
275
269
263
256
1148 1619 2053 2520 2899 3442 3906 4337 4819
130
183
232
285
328
389
441
490
544
334
331
328
324
320
314
307
301
293
1112 1609 2014 2458 2929 3407 3872 4347 4777
126
182
228
278
331
385
437
491
540
372
369
366
363
358
353
346
339
331
1053 1530 1934 2387 2868 3347 3804 4254 4698
119
173
219
270
324
378
430
481
531
410
407
404
401
396
390
383
375
367
994 1450 1855 2316 2806 3287 3737 4162 4618
112
164
210
262
317
371
422
470
522
448
446
443
439
434
427
420
412
403
950 1411 1820 2276 2768 3233 3688 4116 4493
107
159
206
257
313
365
417
465
508
467
464
462
458
453
446
439
431
423
726 1214 1645 2072 2577 2961 3443 3889 3866
439
437
82
137
186
234
291
335
389
563
559
555
556
550
545
536
527
521
[2072]
234
556
C-2-4
}
Torque [lb-in]
Nm
Speed RPM
5127
579
21
5125
579
46
5218
590
77
5311
600
113
5297
598
146
5283
597
180
5261
594
214
5240
592
249
5245
593
285
5250
593
322
5407
611
17
5509
622
42
5610
634
72
5712
645
108
5715
646
140
5718
646
174
5690
643
208
5661
640
243
5644
638
278
5627
636
315
5569
629
11
5880
664
37
6015
680
66
6151
695
103
6147
695
134
6144
694
167
5855
662
8
6249
706
31
6408
724
60
6567
742
98
6563
742
129
6568
742
164
6547
740
24
6754
763
52
6961
786
91
6753
763
19
7436
840
47
7334
829
83
4000 Compact
Series
250 cm3/r [15.4 in3/r]
Performance Data
[250] [500] [750] [1000] [1250] [1500] [1750] [2000] [2250] [2500] [2750] [3000] [3250] [3500] [3750]
15
35
50
70
85 105 120 140 155 170 190 205 225 240 260
in production.
[0.5]
1,9
[1]
3,8
[2]
7,5
[4]
15
[6]
Continuous
23
[8]
Intermittent
30
[10]
Peak
Flow LPM [GPM]
No Operation
38
[12]
45
[14]
53
[16]
61
[18]
68
[20]
76
[22]
83
[24]
91
[25]
95
[30]
114
384
43
6
438
49
14
492
56
28
603
68
58
587
66
88
571
65
118
552
62
148
532
60
178
441
50
209
349
39
239
306
35
269
263
30
300
833
94
5
904
102
14
1054
119
27
1183
134
56
1159
131
86
1135
128
116
1138
129
146
1140
129
177
1072
121
207
1003
113
237
940
106
267
876
99
298
826
93
328
776
88
359
732
83
374
509
57
450
1403
158
13
1563
177
26
1771
200
55
1741
197
84
1710
193
114
1671
189
144
1631
184
175
1600
181
205
1568
177
235
1513
171
265
1458
165
296
1414
160
326
1370
155
356
1322
149
371
1082
122
449
1887
213
12
2081
235
25
2275
257
54
2329
263
82
2384
269
112
2304
260
142
2224
251
173
2207
249
202
2190
247
233
2114
239
263
2038
230
293
1991
225
323
1945
220
354
1959
221
369
2029
229
445
[2246]
254
442
}
2359
267
11
2623
296
24
2817
318
52
2815
318
80
2813
318
110
2804
317
139
2796
316
170
2754
311
199
2711
306
229
2653
300
259
2595
293
290
2528
286
320
2462
278
350
2426
274
365
2246
254
442
2798
316
9
3160
357
23
3364
380
50
3369
381
77
3375
381
107
3361
380
136
3347
378
166
3320
375
195
3292
372
225
3251
367
255
3210
363
285
3144
355
315
3079
348
345
3026
342
360
2761
312
437
3221
364
8
3717
420
21
3895
440
47
3951
446
74
4008
453
103
3950
446
131
3892
440
161
3888
439
190
3884
439
220
3830
433
250
3777
427
280
3709
419
309
3642
411
339
3594
406
354
3358
379
430
3657
413
7
4147
469
17
4495
508
44
4483
506
71
4471
505
100
4452
503
127
4434
501
157
4433
501
185
4431
501
214
4380
495
243
4328
489
272
4262
482
302
4196
474
332
4153
469
347
3939
445
423
3822
432
4
4585
518
16
5005
565
42
5021
567
67
5038
569
96
5006
566
123
4974
562
151
4958
560
179
4941
558
208
4904
554
236
4867
550
265
4806
543
295
4745
536
325
4696
531
340
4450
503
414
4326
489
3
5070
573
13
5496
621
38
5555
628
63
5613
634
92
5587
631
119
5561
628
146
5529
625
174
5496
621
202
5446
615
230
5395
610
259
5354
605
288
5313
600
317
5152
582
333
4347
491
413
5470
618
9
5982
676
35
6068
686
59
6154
695
87
6123
692
113
6093
688
141
6066
685
168
6039
682
195
5984
676
223
5928
670
251
5915
668
279
5901
667
308
5721
646
7
6500
734
32
6557
741
55
6614
747
83
6612
747
109
6610
747
136
6590
745
162
6570
742
189
6518
736
214
6471
731
241
5962
674
5
7054 7519 7941
797 850 897
28
24
17
7131 7641 8107
806 863 916
50
45
38
7209 7763 8272
815 877 935
78
73
67
7201
814
102
7193
813
129
C-2
Torque [lb-in]
Nm
Speed RPM
C-2-5
4000 Compact
Series
325 cm3/r [19.8 in3/r]
Performance Data
in production.
[0.5]
1,9
[1]
3,8
[2]
7,5
[4]
15
[6]
23
[8]
Intermittent
30
[10]
Peak
38
[12]
No Operation
Flow LPM [GPM]
Continuous
45
[14]
53
[16]
61
[18]
68
[20]
76
[22]
83
[24]
91
[25]
95
[30]
114
[250]
15
[500]
35
[750] [1000] [1250] [1500] [1750] [2000] [2250] [2500] [2750] [3000] [3250] [3500]
50
70
85
105
120
140
155
170
190
205
225
240
536
61
5
555
63
11
643
73
22
679
77
45
654
74
68
629
71
92
587
66
115
546
62
139
489
55
162
431
49
186
360
41
210
288
33
234
1152
130
4
1220
138
10
1349
152
21
1420
160
44
1400
158
67
1379
156
90
1337
151
114
1295
146
137
1238
140
161
1182
134
185
1110
125
208
1038
117
232
958
108
256
878
99
279
826
93
291
566
64
351
1900
215
10
2025
229
20
2140
242
43
2132
241
66
2125
240
89
2082
235
112
2040
230
136
1984
224
159
1929
218
183
1856
210
206
1784
202
230
1706
193
254
1628
184
277
1576
178
289
1314
148
349
[2799]
316
342
C-2-6
2559
289
9
2712
306
19
2852
322
42
2859
323
64
2866
324
87
2827
319
110
2787
315
134
2729
308
157
2671
302
181
2600
294
204
2529
286
228
2451
277
251
2373
268
275
2320
262
287
2056
232
346
}
3222
364
9
3378
382
19
3557
402
40
3575
404
62
3592
406
85
3556
402
107
3520
398
130
3467
392
153
3415
386
177
3343
378
200
3271
370
224
3194
361
248
3116
352
271
3063
346
283
2799
316
342
3862
436
8
4051
458
17
4259
481
38
4281
484
59
4304
486
82
4272
483
103
4240
479
125
4193
474
148
4145
468
171
4073
460
195
4001
452
220
3926
444
243
3850
435
266
3798
429
277
3536
399
337
Torque [lb-in]
Nm
Speed RPM
4522
511
7
4696
531
15
4947
559
36
4977
562
56
5007
566
79
4976
562
100
4944
559
121
4903
554
143
4861
549
165
4794
542
189
4726
534
214
4650
525
237
4574
517
260
4523
511
271
4268
482
332
5061
572
5
5335
603
13
5628
636
33
5668
640
53
5707
645
75
5672
641
94
5638
637
115
5600
633
136
5562
628
159
5499
621
183
5436
614
207
5360
606
229
5285
597
252
5580
630
3
5889
665
10
6300
712
30
6346
717
49
6392
722
71
6362
719
90
6332
715
110
6293
711
131
6254
707
153
6106
690
3
6366
719
5
6960
786
26
7021
793
44
7082
800
66
7053
797
85
7023
794
105
6876
777
3
7596
858
23
7678
868
40
7760
877
61
8201
927
19
8244
931
38
8400
949
56
8767
991
14
8792
993
35
9320
1053
11
4000 Compact
Series
Performance Data
Continuous
Intermittent
Peak
No Operation
[0.5]
1,9
[1]
3,8
[2]
Flow LPM [GPM]
in production.
405 cm3/r [24.6 in3/r]
7,5
[4]
15
[6]
23
[8]
30
[10]
38
[12]
45
[14]
53
[16]
61
[18]
68
[20]
76
[22]
83
[24]
91
[25]
95
[30]
114
[250]
15
[500]
35
[750]
50
[1000] [1250] [1500] [1750] [2000] [2250] [2500]
70
85
105
120
140
155
170
719
81
3
777
88
8
853
96
17
878
99
35
882
100
54
885
100
73
810
92
92
735
83
111
661
75
130
587
66
149
492
56
168
397
45
188
1458
165
2
1631
184
7
1812
205
15
1859
210
34
1836
207
52
1813
205
72
1736
196
90
1660
188
110
1622
183
128
1585
179
147
1472
166
167
1359
153
186
1264
143
205
1169
132
224
1106
125
233
790
89
282
2423
274
5
2596
293
14
2687
304
32
2716
307
51
2746
310
70
2693
304
89
2640
298
108
2560
289
127
2480
280
146
2379
269
165
2279
257
184
2194
248
203
2110
238
222
2049
231
232
1744
197
280
3148
356
4
3375
381
12
3667
414
30
3680
416
48
3694
417
68
3639
411
86
3584
405
106
3512
397
124
3440
389
143
3333
377
162
3226
365
182
3124
353
201
3023
342
220
2961
335
229
2655
300
277
[2655]
300
227
}
3690
417
3
4179
472
11
4554
515
28
4577
517
46
4600
520
65
4540
513
84
4480
506
103
4412
498
121
4343
491
141
4270
482
160
4197
474
179
4093
462
198
3989
451
216
3929
444
226
3634
411
274
4845
547
9
5388
609
25
5388
609
42
5388
609
62
5390
609
80
5391
609
98
5330
602
117
5268
595
137
5190
586
156
5112
578
175
5008
566
193
4904
554
212
4851
548
222
4587
518
270
5375
607
8
6232
704
23
6269
708
39
6307
713
58
6310
713
75
6314
713
93
6242
705
112
6170
697
131
6084
687
150
5999
678
170
5904
667
188
5810
656
207
5766
651
217
5543
626
266
5841
660
3
7004
791
19
7079
800
35
7153
808
55
7151
808
71
7149
808
88
7059
798
108
6501
735
2
7660
865
16
7856
888
31
8052
910
50
7994
903
67
8153
921
11
C-2
Torque [lb-in]
Nm
Speed RPM
C-2-7
4000 Compact
Series
490 cm3/r [29.8 in3/r]
Performance Data
in production.
[0.5]
1,9
[1]
3,8
[2]
7,5
[4]
15
[6]
Continuous
23
[8]
Intermittent
No Operation
Flow LPM [GPM]
Peak
30
[10]
38
[12]
45
[14]
53
[16]
61
[18]
68
[20]
76
[22]
83
[24]
91
[25]
95
[30]
114
[250]
15
[500]
35
[750]
50
[1000] [1250] [1500] [1750] [2000] [2250] [2500]
70
85
105
120
140
155
170
375
42
3
525
59
7
639
72
14
981
111
30
1049
119
45
1118
126
61
1060
120
76
1003
113
92
858
97
108
713
81
124
631
71
139
548
62
155
1669
189
3
1762
199
7
2108
238
14
2201
249
29
2218
251
45
2236
253
60
2230
252
76
2223
251
91
2127
240
107
2030
229
123
1907
215
139
1784
202
154
1669
189
170
1553
175
186
1469
166
193
1047
118
232
2945
333
6
3287
371
13
3333
377
29
3332
376
44
3331
376
60
3304
373
75
3276
370
91
3136
354
107
2997
339
122
2935
332
138
2872
325
153
2704
306
169
2536
287
185
2475
280
193
2172
245
232
3965
448
6
4169
471
13
4574
517
28
4584
518
43
4593
519
59
4503
509
75
4413
499
90
4320
488
106
4226
477
122
4133
467
137
4041
457
153
3928
444
169
3816
431
185
3737
422
193
3341
378
232
[3341]
378
232
C-2-8
}
Torque [lb-in]
Nm
Speed RPM
5099
576
6
5416
612
11
5558
628
27
5604
633
42
5650
638
58
5607
633
73
5564
629
89
5496
621
105
5428
613
121
5330
602
136
5232
591
152
5048
570
168
4864
550
184
4810
543
192
4538
513
231
5926
670
5
6570
742
11
6634
750
26
6670
754
40
6705
758
56
6693
756
72
6680
755
88
6542
739
103
6403
723
119
6339
716
134
6275
709
150
6124
692
166
5972
675
182
5909
668
190
5592
632
229
6715
759
4
7188
812
9
7694
869
24
7711
871
38
7727
873
54
7721
872
69
7715
872
85
7653
865
100
7590
858
115
7431
840
130
7362
832
148
7208
814
164
7055
797
179
6959
786
187
6482
732
227
7503
848
3
8295
937
6
8627
975
21
8713
984
35
8798
994
51
8836
998
66
8874
1003
82
8959
1012
5
9567
1081
18
9698
1096
31
9828
1110
48
10399
1175
13
10588
1196
26
10778
1218
44
4000 Compact
Series
Ports
or
PortUN-2B
B
Port B Ports (Positioned 180° Apart) (2)
1 1/16 -12
SAE O-ring
YY Max.
7/8 -14 UNF-2B
XXSAE O-ring End Ports (2)
7/16 -20 UNF-2B SAE O-ring Case
Y Max.Drain Port (1) or
X
Manifold Mount
Dimensions
Standard Mount
Standard Mount
Port B
Port B
YY Max.
XX
Y Max.
X
YY Max.
C-2
STandard Mount Motor Dimensions
YY Max.
Displacement
cm3/r [in3/r]
160 [9.8]
200 [12.3]
250 [15.4]
325 [19.8]
405 [24.6]
490 [29.8]
X
mm [inch]
154,7 [6.09]
163,8 [6.45]
175,3 [6.90]
191,0 [7.52]
208,5 [8.21]
208,5 [8.21]
Y
mm [inch]
201,9 [7.95]
211,1 [8.31]
222,5 [8.76]
238,5 [9.39]
255,8 [10.07]
255,8 [10.07]
XX
mm [inch]
YY
mm [inch]
157,0
166,1
177,5
193,3
210,8
210,8
203,3 [8.00]
212,3 [8.36]
223,8 [8.81]
239,8 [9.44]
257,0 [10.12]
257,0 [10.12]
[6.18]
[6.54]
[6.99]
[7.61]
[8.30]
[8.30]
C-2-9
4000 Compact Series
Ports
Dimensions
or
Port B Staggered Port
B (2)
G 1/2 (BSP)
Ports
G 1/4 (BSP) Case
Drain Port (1) or
Y Max.
XX
Manifold Mount
Wheel Mount
Y Max.
X Shaft End
Standard Rotation Viewed from
Wheel Mount
Port B
Y Max.
XX
Port B
Y Max.
X
YY Max.
YY Max.
Wheel Mount motor dimensions
DisplacementX
cm3/r [in3/r] mm [inch]
160 [ 9.8]
114,6 [4.51] 200 [12.3]
123,7 [4.87] 250 [15.4] 135,1 [5.32] 325 [19.8] 150,9 [5.94] 405 [24.6] 168,4 [6.63] 490 [29.8]
168,4 [6.63] 7/8-14 UNF-2B SAE O-ring End Ports
C-2-10
Y
mm [inch]
161,8 [6.37] 170,9 [6.73] 182,4 [7.18] 198,4 [7.81] 215,6 [8.49] 215,6 [8.49]
XXYY
mm [inch]
mm [inch
114,6 [4.51]
123,7 [4.87]
135,1 [5.32]
150,9 [5.94]
168,4 [6.63]
168,4 [6.63]
161,8 [6.37]
170,9 [6.73]
182,4 [7.18]
198,4 [7.81]
215,6 [8.49]
215,6 [8.49]
4000 Compact Series
Ports
Dimensions
or
Manifold Mount
Bearingless
Bearingless
YY Max.
XX
Port B
Port B
For 4000 bearingless motor
application information,
contact your Eaton representative (mating coupling
blanks available from Eaton
Hydraulics).
Y Max.
X
101,60/101,47
[4.000/3.995]
Pilot Dia.
Note:
After machining blank,
part must be hardened
per Eaton specification.
C
D
E
F
G
H
J
K
1 1/16-12 UN-2B SAE O-ring Ports
YY Max.
16,8/15,2
[.66/.60]
157,5
[6.20]
Max. (2)
6.7/6,0
[.26/.24]
C
D
K
J
47,2 [1.86] Dia.
112,5 [4.43] Max.
107,4 [4.23] Full Form Dia.
7,4 [.29]Min. Full Form Dia.
68,8 [2.71] Max.
56,9 [2.24] Dia.
18,29 [.720]
38º
E
F
G
H
127,0
[5.00]
Dia.
13,85/13,33
[.545/.525]
Dia. Thru (4)
119,2
[4.69]
Sq. Max.
14,22 [.560]
Min. (4)
O-ring Seal
Furnished
with Motor
24,06/23,54
[.947/.927]
DisplacementX
160 [9.8]
96,8 [3.81]
200 [12.3]
105,7 [4.16]
250 [15.4] 117,1 [4.61]
325 [19.8] 133,1 [5.24]
405 [24.6] 150,4 [5.92]
490 [29.8]
150,4 [5.92]
Y
mm [inch]
144,3 [5.68]
153,4 [6.04]
164,8 [6.49]
180,8 [7.12]
198,1 [7.80]
198,1 [7.80]
XXYY
mm [inch]
mm [inch]
99,1 [3.90]
108,0 [4.25]
119,4 [4.70]
135,4 [5.33]
152,7 [6.01]
152,7 [6.01]
145,5 [5.73]
154,7 [6.09]
166,1 [6.54]
182,1 [7.17]
199,4 [7.85]
199,4 [7.85]
C-2-11
C-2
4000 Compact Series
1 Internal spline in mating part to be per
spline data specification. Material to be
ASTM A304, 8620H vacuum degassed
alloy steel carbonize to a hardness of
59-62 HRc with case depth (to 50HRc) of
0,76 - 1,02 [.030 - .040] dimensions apply
after heat treat.
2 Mating part to have critical dimensions
as shown. Oil holes must be provided and
3 Seal to be furnished with motor for proper
oil circulation thru splines.
Bearingless
18,6/17,5
[.73/.69]
49,848/49,822
[1.9625/1.9615]
0,13 [.005] B
-D16
1,3/0,8
[.05/.03]
be provided.
5 Counterbore designed to adapt to a
standard sleeve bearing 50,010 - 50,040
[1.9689 - 1.9700] ID by 60,050 - 60,080
[2.3642 - 2.3653] (Oilite bronze sleeve
bearing) Source: Beemer Precision Inc.
www.oilite.com, 1-800-836-2340
AAM 50 mm ID - 60 mm OD Length
Determined by the Customer.
Stock Bearing Lengths:
35 mm
50 mm
60 mm
70 mm
75 mm
-B-
12,6/12,3
[.495/486]
1,5/0,8
[.06/.03]
R 1,8/1,3
[.07/.05]
31º/ 29º
30º/15º
15,2 [.60] Min.
52,37
[2.062]
Min.
34,04/33,53
[1.340/1.320]
5
-A-
R 1,8/1,3
[.07/.05]
Bearing Length Will
Determine this
Dimension
58,7/58,2
[2.31/2.29]
5,1/4,6
2
2X [.20/.18]
Thru Oil Hole
5,6/5,1 [.22/.20]
31,0/30,5
[1.22/1.20]
Spline Pitch.................................................................................................. 10/20
Pressure Angle................................................................................................30°
Number of teeth............................................................................................... 12
Class of Fit................................................................................................... Ref. 5
Type of Fit...................................................................................................... Side
| 0,20 [.008] | D
Pitch Diameter.....................Ref. 30,480000 [1.2000000]
Base Diameter........................................................ Ref. 26,396455 [1.0392305]
Major Diameter.................................. (33,43 [1.316] Max. 33,23 [1.308] Min.)
Minor Diameter..................................................... 28,40 - 25,58 [1.118 - 1.125]
Form Diameter, Min........................................................................32,59 [1.283]
Fillet Radius.................................................................... 0,63 - 0,76 [.025 - .030]
Tip Radius....................................................................... 0,26 - 0,51 [.010 - .020]
Finish..........................................................................................................1,6 (63)
Involute Profile Variation...................................+0,000 -0,025 [+.0000 -.0010]
Total Index Variation......................................................................0,038 [.0015]
Lead Variation.................................................................................0,013 [.0005]
Maximum Actual......................................................................5,045 [.1986]
Minimum Effective...................................................................4,995 [.1951]
Maximum Effective..........................................................Ref. 5,009 [.1972]
Minimum Actual...............................................................Ref. 4,986 [.1963]
Dimension Between Two Pins...............Ref. 22,783 - 22,929 [.8970 - .9027]
Pin Diameter.........................................5,334 [.2100] Pins to Have 3,73 [.147]
.
C-2-12
Oil Flow Return
to Case Drain*
3
4
Oil Flow Path
Thru Spline
Circular
Major
37,31/36,80
[1.469/1.449]
Coupling Depth
Finish
Finish
Tip R.
Minor
Fillet R.
Pitch
Form
4000 Compact Series
Dimensions
Mounting Options
Four Bolt Magneto
SAE A — Two Bolt (Standard Motor)
131,1 [5.16] Max.
131,1
[5.16]
Max.
106,38
[4.188]
131,1
[5.16] Max.
106,38 [4.188]
106,38 [4.188]
18,6/17,0
18,6/17,0
[.73/.67]
18,6/17,0
[.73/.67]
[.73/.67]
82,55/82,42
18,6/17,0
82,55/82,42
[3.250/3.245]
18,6/17,0
[.73/.67]
13,85/13,33
[3.250/3.245]
18,6/17,0
Pilot82,55/82,42
Dia.
[.73/.67]
13,85/13,33
[.545/.525]
2,8/2,3
[3.250/3.245]
Pilot
Dia.
[.73/.67]
13,85/13,33
[.545/.525]
2,8/2,3
Dia. Thru (4)
[.11/.09]
Pilot Dia.
[.545/.525]
2,8/2,3
Dia. Thru
(4)
[.11/.09]
Dia. Thru (4)
[.11/.09]
45°
45°
13,85/13,33
13,85/13,33
[.545/.525]
6,4 [.25]
[.545/.525]
Dia.13,85/13,33
Thru
82,55/82,42
6,4 [.25]
[.545/.525]
Dia.
22,16,4[.87]
82,55/82,42
(2)Thru
[3.250/3.245]
[.25]
22,1
[.87]
(2) Dia. Thru [3.250/3.245]
Max.
Pilot82,55/82,42
Dia.
(2)
[3.250/3.245] Max. 22,1 [.87]
Pilot Dia.
Max.
Pilot Dia.
22,7/21,8
22,7/21,8
[.89/.86]
[.89/.86]
Dia.22,7/21,8
(2)
Dia. (2)[.89/.86]
Dia. (2)
Two Bolt SAE B
101,60/101,47
101,60/101,47
[4.000/3.995]
[4.000/3.995]
Pilot101,60/101,47
Dia.
[4.000/3.995]
Pilot Dia.
Pilot Dia.
146,05
146,05
[5.750]
176,8 [5.750]146,05
176,8
[5.750]
[6.96]
[6.96]
Max.176,8
Max. [6.96]
Max.
14,53/14,14
14,53/14,14
[.572/.557]
[.572/.557]
Dia.14,53/14,14
Thru (2)
[.572/.557]
Dia. Thru
(2)
Dia. Thru (2)
57,2/50,8
57,2/50,8
[2.25/2.00]
57,2/50,8
[2.25/2.00]
Dia.
Dia.[2.25/2.00]
Dia.
9,7/9,1
9,7/9,1
[.38/.36]
9,7/9,1
[.38/.36]
[.38/.36]
134,2
134,2
[5.28]
[5.28]
Max.134,2
Sq.
[5.28]
Max. Sq.
Max. Sq.
22,7/21,8
22,7/21,8
[.89/.86]
[.89/.86]
Dia.22,7/21,8
(4)
21,9 [.87] Dia. (4)[.89/.86]
21,9Max.
[.87]
Dia. (4)
Max.21,9 [.87]
Max.
Four Bolt
18,6/17,0
82,55/82,42
18,6/17,0
82,55/82,42
[.73/.67]
[3.250/3.245]
6,7/6,0
18,6/17,0
[.73/.67]
[3.250/3.245]
Pilot82,55/82,42
Dia.
6,7/6,0
[.27/.24]
[.73/.67]
[3.250/3.245]
13,72/13,46
6,7/6,0
Pilot Dia.
[.27/.24]
Pilot Dia.
[.540/.530]
[.27/.24] 13,72/13,46
[.540/.530]
Dia.13,72/13,46
Thru (4)
[.540/.530]
Dia. Thru
(4)
Dia. Thru (4)
22,1/17,0
22,1/17,0
[.87/.67]
22,1/17,0
[.87/.67]
[.87/.67]
47,3/ 45,7
47,3/
45,7
[1.86/1.80]
47,3/ 45,7
[1.86/1.80]
[1.86/1.80]
147,638
147,638
[5.8125]
[5.8125]
Dia.147,638
Dia.
Bolt[5.8125]
Circle
Dia.
Bolt Circle
Bolt Circle
107,95/107,82
107,95/107,82
[4.250/4.245]
[4.250/4.245]
Pilot107,95/107,82
Dia.
[4.250/4.245]
Pilot Dia.
Pilot Dia.
13,85/13,33
13,85/13,33
[.545/.525]
[.545/.525]
Dia.13,85/13,33
Thru
[.545/.525]
Dia. Thru
Dia. Thru
106,38 [4.188] Dia.
106,38 [4.188] Dia.
135,7[4.188]
[5.34] Dia.
Max.
106,38
135,7 [5.34] Max.
135,7 [5.34] Max.
45°
106,38
106,38
[4.188]
[4.188]
Dia.106,38
Bolt Circle
[4.188]
Dia. Bolt
Circle
Dia. Bolt Circle
108,8
108,8
[4.28]
[4.28]
Max.108,8
Sq.
[4.28]
Max. Sq.
Max. Sq.
20,1 [.79]
20,1
[.79]
Max.
Max. 20,1 [.79]
Max.
6,4
6,4[.25]
[.25] 6,4
[.25]
22,7/21,8
22,7/21,8
[.89/.86]
[.89/.86]
Dia.22,7/21,8
(4)
Dia. (4)[.89/.86]
Dia. (4)
22,7/22,0
22,7/22,0
[.89/.87]
22,7/22,0
[.89/.87]
3,8/2,8
[.89/.87]
3,8/2,8
[.15/.11]
3,8/2,8
[.15/.11]
[.15/.11]
127,00/126,87
127,00/126,87
[5.000/4.995]
[5.000/4.995]
Dia.127,00/126,87
Dia. [5.000/4.995]
Dia.
6,7/6,0
[.26/.24]
6,7/6,0
[.26/.24]
6,7/6,0
[.26/.24]
C-2
C-2-13
4000 Compact Series
Dimensions
Mounting Options for use with Enhanced Bearings
Standard Flange- Similar to SAE B type
119,9 [4.72]
Max Square
119,9 [4.72]
Max Square
15,2/14,5
[.60/.57] (4)
15,2/14,5
[.60/.57] (4)
[.60/.57] (4)
148,8
[5.86]
148,8Sq.
Max
[5.86]
Max Sq.
148,8
[5.86]
Max Sq.
Four Bolt (Wheel Motor- Short)
137,41
[5.410]
Max Sq.
C-2-14
101,60/101,47
[4.000/3.995]
101,60/101,47
Dia.
[4.000/3.995]
Dia.
10,62/9,19
[.418/.362]
101,60/101,47
[4.000/3.995]
Dia.
15,2/14,5
137,41
[5.410]
137,41
Max
Sq.
[5.410]
Max Sq.
[.418/.362]
119,9 [4.72]
Max Square
89,80
[3.536]
89,80
Square
[3.536]
Square
89,80
[3.536]
Square
10,62/9,19
[.418/.362]
10,62/9,19
127,0 [5.00]
Dia. Bolt Circle
127,0 [5.00]
Dia. Bolt Circle
22,30/21,89
[.878/.862]
22,30/21,89
[.878/.862]
127,0 [5.00]
[6.500]
Dia. 165,10
Bolt Circle
Dia. Bolt Circle
165,10 [6.500]
Dia. Bolt Circle
165,10 [6.500]
Dia. Bolt Circle
13,69/13,28
[.539/.523]
13,69/13,28
Dia. Thru (4)
[.539/.523]
Dia. Thru (4)
22,6/22,1
[.89/.87]
22,6/22,1
[.89/.87]
139,70/139,57
[5.500/4.495]
139,70/139,57
Pilot Dia.
[5.500/4.495]
Pilot Dia.
139,70/139,57
[5.500/4.495]
Pilot Dia.
13,69/13,28
147,62 [5.812]
[.539/.523]
Dia. Bolt Circle
Dia.
Thru[5.812]
(4)
147,62
Dia. Bolt Circle
147,62 [5.812]
Dia. Bolt Circle
22,6/22,1
[.89/.87]
9,7/8,6
[.38/.34]
9,7/8,6
[.38/.34]
23,1/22,1
9,7/8,6
[.91/.81]
[.38/.34]
23,1/22,1
[.91/.81]
23,1/22,1
127,00/126,87[.91/.81]
[5.000/4.995]
127,00/126,87
Pilot
Dia.
[5.000/4.995]
Pilot Dia.
13,84/13,34
[.545/.525]
13,84/13,34
Dia. Thru (4)
[.545/.525]
Dia. Thru (4)
127,00/126,87
[5.000/4.995]
Pilot Dia.
14,7/13,7
[.58/.54]
14,7/13,7
[.58/.54]
13,84/13,34
[.545/.525]
Dia. Thru (4)
14,7/13,7
[.58/.54]
22,30/21,89
[.878/.862]8,4/7,9
[.33/31]
8,4/7,9
[.33/31]
8,4/7,9
139,70/139,57
[.33/31]
[5.500/4.495]
139,70/139,57
Rear Pilot Dia.
[5.500/4.495]
Rear Pilot Dia.
139,70/139,57
[5.500/4.495]
Rear Pilot Dia.
4,1/4,6
[.24/.18]
4,1/4,6
[.24/.18]
4,1/4,6
[.24/.18]127,00/126,87
[5.000/4.995]
127,00/126,87
Rear
Pilot Dia.
[5.000/4.995]
Rear Pilot Dia.
127,00/126,87
[5.000/4.995]
Rear Pilot Dia.
4000 Compact Series
Dimensions
Shafts
1-5/8 Inch Tapered
1-1/4 Inch Tapered
972 [8600] Max.
972
[8600]
Torque
NmMax.
972
[8600]
Torque
NmMax.
[lb-in]
Torque
[lb-in] Nm
1-1/4-18 UNEF
[lb-in]
1-1/4-18 UNEF
1-1/4-18 UNEF
164,8/162,1 [6.49/6.38] End of Shaft
164,8/162,1
End of Shaft
Surface (Whl)
164,8/162,1
End of Shaft
to
Mounting [6.49/6.38]
Surface (Whl)
31,7 [1.25]
31,7 [1.25]
31,7 [1.25]
41,326/41,275
41,326/41,275Dia.
[1.6270/1.6250]
41,326/41,275Dia.
[1.6270/1.6250]
[1.6270/1.6250] Dia.
4,1 [.16]
4,1
76,6
Dia.[.16]
Thru
76,6
4,1 [.16]
Dia.
Thru
[3.00]
76,6
[3.00]
Dia. Thru
[3.00]
SAE
J501
Standard
Tapered
Shaf
t
125,00 0,17 Taper per Mete r
SAE
J501
Standard
125,00
0,17
Taper per
perTapered
Mete rShaf t
[1.500±.002
Taper
Foot]
125,00 0,17 Taper
Taper per
per Foot]
Mete r
[1.500±.002
[1.500±.002 Taper per Foot]
5,54/5,20
5,54/5,20
[.218/.205]
5,54/5,20
[.218/.205]
[.218/.205]
11,138/11,112
11,138/11,112
[.4385/.4375]
11,138/11,112
[.4385/.4375]
Sq.
Key
[.4385/.4375]
Sq.
Key
Sq. Key
Tapered Shaft Hub
Data
59,1/56,8
768 [6800]
105,5/102,8 [4.15/4.05] End of Shaft
768 [6800]
105,5/102,8 [4.15/4.05] End of Shaft
Max.
Torqu e
to
Mounting Surface (Whl)
768
[6800]
Max.[lb-in]
Torqu e
105,5/102,8
End of Shaft
Nm
Surface (Whl)
Max.
Torqu e
Nm [lb-in]
Nm [lb-in]
12,7 [.50]
26,2/24,6
12,7 [.50]
26,2/24,6
[1.03/.97]
12,7
1-20[.50]
UNEF
26,2/24,6
[1.03/.97]
1-20 UNEF
[1.03/.97]
1-20 UNEF
4,1 [.16]
4,1
Dia.[.16]
Thru
4,1 [.16]
Dia.
Thru
Dia. Thru
31,7 [1.250] Dia.
31,7 [1.250]
Dia.
55,1 [2.17]
55,1 [2.17]
31,7 [1.250]
Dia.
SAE J501
Tapered Shaf t
55,1 Standard
[2.17]
SAE
J501
Standard
125,00 0,17 Taper perTapered
Mete rShaf t
SAE
J501
Standard
125,00
0,17
Taper
per
Mete rShaf t
[1.500±.002 Taper perTapered
Foot]
125,00 0,17 Taper
Taper per
per Foot]
Mete r
[1.500±.002
7,963/7,937
7,963/7,937
[.3135/.3125]
7,963/7,937
[.3135/.3125]
Square Key
[.3135/.3125]
Square
Key
Square Key
3,97/3,63 [.156/.143]
3,97/3,63
[.156/.143]
at
Large End
of Tape r
3,97/3,63
[.156/.143]
at Large End
of Tape r
at Large End of Tape r
59,1/56,8
[2.325/2.235]
59,1/56,8
[2.325/2.235]
[2.325/2.235]
Hub
Hub
Hub
38,1 [1.50]
38,1 [1.50]
38,1
Hub[1.50]
Recommended Torque : Hub
Hub
Recommended
Torque
(373 Nm [275 lb-ft]
Dry) :
Recommended
Torque
:
(373
Nm
[275
lb-ft]
Dry)
(305 Nm [225 lb-ft] Lub)
(373
[275required
Dry)
(305
[225
lb-ft] Lub)
Plus Nm
Torque
t o
(305
lb-ft]
Plus
Torque
required
t o
alignNm
the [225
slotted
nutLub)
with
Plus
Torque
required
t o
align
the slotted
nut with
the Shaft
Crosshole.
alignShaft
the slotted
nut with
the
Crosshole.
Recommended Torque :
Recommended
Torque
(645 Nm [475 lb-ft]
Dry) :
Recommended
Torque
(645
Dry)
(510 Nm
Nm [475
[375 lb-ft]
lb-ft]
Lub) :
(645
[475required
Dry)
(510
[375
lb-ft] Lub)
Plus Nm
Torque
t o
(510
lb-ft]
Plus
Torque
required
t o
alignNm
the [375
slotted
nutLub)
with
Plus
Torque
required
t o
align
the slotted
nut with
the Shaft
Crosshole.
alignShaft
the slotted
nut with
the
Crosshole.
Slotted Hexagon Nut
Slotted Hexagon Nut
55,4 [2.18]
55,4 [2.18]
55,4 [2.18]
36,6
36,6
[1.44]
36,6
[1.44]
[1.44]
11,2 [.44]
11,2 [.44]
11,2 [.44]
4,1 [.16]
4,1 [.16]
4,1 [.16]
1-1/4-18 UNEF
1-1/4-18 UNEF
1-1/4-18 UNEF
30°
30°
30°
C-2
Tapered Shaft Hub Data
30°
30°
30°
15,7 [.62]
15,7 [.62]
15,7 [.62]
1-20 UNEF-2B
1-20 UNEF-2B
1-20 UNEF-2B
30 °
30 °
30 °
4,6 [.18]
4,6 [.18]
4,6 [.18]
30 °
30 °
30 °
8,1 [.32]
8,1 [.32]
8,1 [.32]
12,7 [.50]
12,7 [.50]
12,7 [.50]
C-2-15
4000 Compact Series
Dimensions
Shafts
1-1/4 Inch Straight
1-1/2 Inch Straight
972 [8600]
Max. Torqu e
Nm [lb-in]
9,55/9,53
[.376/.375]
Square Key
79,5 /77,5 [3.13/3.05] End of Shaft
57,9/56,6
79,5 /77,5 [3.13/3.05]
End of Shaft
[2.28/2.23]
42,39/42,14 to Mounting Surface
(Std)
9,55/9,53
79,5
/77,5
[3.13/3.05]
End of Shaft
[1.669/1.659]
[.376/.375]
9,55/9,53
Square Key
[.376/.375]
57,9/56,6
Square 42,39/42,14
Key
[2.28/2.23]
57,9/56,6
[1.669/1.659]
[2.28/2.23]
42,39/42,14
[1.669/1.659]
3/8-16 UNC-2B
38,10/38,05
18,7 [.74] Min.
[1.500/1.498]
Full Thread
Dia.
67,8 [2.67]
3/8-16 UNC-2B
38,10/38,05
Max. Coupling
18,7 [.74] Min.
[1.500/1.498]
3/8-16 UNC-2B
38,10/38,05
Full Thread
Dia.
18,7 [.74] Min.
[1.500/1.498]
67,8 [2.67]
Full
Thread
Dia.
972 [8600]
Max. Coupling
67,8 [2.67]
Max. Torqu e
89,7/87,6
[3.53/3.45] End of Shaft
40
mm
Straight
Max. Coupling
12,000/11.957
Nm [lb-in]
to Mounting
Surface (Std)
[.4724/.4708]
972 [8600]
9,2/4,5 [.36/.18]
8,000/7,900
70,7/69,3
Max. Torqu
e
89,7/87,6 [3.53/3.45] End
of Shaft
972 [8600][.3149/.3115]
12,000/11.957
[2.78/2.73]
Nm [lb-in]
Max. Torqu e
89,7/87,6 [3.53/3.45] End of Shaft
[.4724/.4708]
12,000/11.957
Nm [lb-in]
9,2/4,5 [.36/.18]
8,000/7,900[.4724/.4708]
70,7/69,3
43,03/42,72
9,2/4,5 [.36/.18] [2.78/2.73]
[.3149/.3115]
8,000/7,900
70,7/69,3
[1.694/1.682]
[.3149/.3115]
[2.78/2.73]
972 [8600]
Max. Torqu e
972 [8600]
Nm [lb-in]
Max. Torqu e
Nm [lb-in]
43,03/42,72
M12 x 1,75 -6H
[1.694/1.682]
24,9 [.98] Deep
43,03/42,72
[1.694/1.682]
40,02/39,99
[1.576/1.575]
Dia.
81,3 [3.20]
Max. Coupling
M12 x 1,75 -6H
24,9 [.98] Deep
M12 x 1,75 -6H
24,9 [.98] Deep
40,02/39,99
[1.576/1.575]
40,02/39,99
Dia.
[1.576/1.575]
Dia.
81,3 [3.20]
Max. Coupling
81,3 [3.20]
Max. Coupling
768 [6800]
Max. Torqu e
Nm [lb-in]
7,963/7,937
[.3135/.3125]
768 [6800]
Max. Torqu e
768 [6800]
Nm [lb-in]
Max. Torqu e
Nm [lb-in]
35,34/35,05
7,963/7,937
[1.391/1.380]
[.3135/.3125]
7,963/7,937
[.3135/.3125]
35,34/35,05
3/8-16 UNC
[1.391/1.380]
35,34/35,05
x 19,0 [.75] Deep
[1.391/1.380]
31,75/31,69 [1.250/1.248] Dia.
3/8-16 UNC
x 19,0 [.75] Deep
3/8-16 UNC
x 19,0
[.75] Deep [1.250/1.248] Dia.
31,75/31,69
31,75/31,69 [1.250/1.248] Dia.
768 [6800]
Max. Torqu e
32
Nmmm
[lb-in] Straight
768 [6800]
Max. Torqu e
768 [6800]
Nm
[lb-in]
35,0/34,7
Max. Torqu e
[1.38/1.37]
Nm [lb-in]
35,0/34,7
[1.38/1.37]
35,0/34,7
[1.38/1.37]
M8
x
1.25 -6H
21.6 [8.5]
Min. Deep
M8 x
1.25 -6H
M8 x
21.6 [8.5]
1.25 -6H
Min. Deep
21.6 [8.5]
Min. Deep
10,00/9,96
[.394/.392]
10,00/9,96
[.394/.392]
10,00/9,96
[.394/.392]
56,4/54,4 [2.22/2.14] End of Shaft
32,6/30,9
[1.28/1.22]
56,4/54,4 [2.22/2.14]
End of Shaft
56,4/54,4 [2.22/2.14] End of Shaft
to Mounting 32,6/30,9
Surface (Std)
[1.28/1.22]
32,6/30,9
[1.28/1.22]
47,3 [1.86]
Max. Coupling
47,3 [1.86]
Max. Coupling
47,3 [1.86]
Max. Coupling
66,0/63,8
[2.60/2.51] End of Shaft
8,7/4,5[3.4/.18]
45,7/45,3
66,0/63,8 [2.60/2.51]
End of Shaft
[1.80/1.74]
to Mounting Surface
(Std)
66,0/63,8 [2.60/2.51] End of Shaft
to Mounting
Surface (Std)
8,7/4,5[3.4/.18]
45,7/45,3
8,7/4,5[3.4/.18]
[1.80/1.74]
45,7/45,3
[1.80/1.74]
32,017/31,991
[1.2605/1.2595]
32,017/31,991
[1.2605/1.2595]
32,017/31,991
[1.2605/1.2595]
56,4 [2.22]
Max. Coupling
56,4 [2.22]
Max. Coupling
56,4 [2.22]
Max. Coupling
64,0/63,8 [2.60/2.51] End of Shaft
63,0/60,7 [2.48/2.39] End of Shaft
972 [8600]
768 [6800]
Max. Torqu e
Max. Torqu e
38,1 [1.50]
1-1/2
1-1/4
Inch 14 Tooth Splined
Nm
[lb-in]Inch 17 Tooth Straight
Nm [lb-in]
64,0/63,8 [2.60/2.51]
Min. End of Shaft
33,28/33,02
(Std)
Spline to Fit ANSI B92.1 to Mounting Surface
63,0/60,7 [1.310/1.300]
[2.48/2.39] EndDia.
of Shaft
Full Spline
972 [8600]
768
[6800]
64,0/63,8
[2.60/2.51]
End of Shaft
31,2 [1.23]
1976 Flat Root Side Fit
Max. Torqu e
to
Mounting
Surface
(Std)
Max. Torqu14e Tooth 12/24 Spline
63,0/60,7 [2.48/2.39] End of Shaft
Min. Full Spline
972 [8600]
768 [6800]
38,1 [1.50]
Nm [lb-in]
Nm [lb-in]
Max. Torqu e
Max. Torqu e
Min.
33,28/33,02
38,1 [1.50]
Nm [lb-in]
Nm [lb-in] Spline to Fit ANSI B92.1
Full Spline
[1.310/1.300]
Dia.
Min.
31,2 [1.23]
33,28/33,02
38,10 [1.500] Dia.
Spline
to
Fit
ANSI
B92.1
Full Spline
Min. Full Spline
[1.310/1.300]
Dia.
14
Tooth
12/24
Spline
31,2 [1.23]
3/8-16
UNC
Min.
Full
Spline
14 Tooth 12/24 Spline
Spline to
3/8-16 UNC
31,7
18,7 [.74] Deep
18,7 [.74] Deep
Fit
ANSI
B92.1
1976
[1.250]
38,10 [1.500] Dia.
Flat Root Side Fit 17 Tooth
Dia.
53,1 [2.09]
51,8 [2.04]
12/24[1.500]
Spline Dia.
38,10
Max.
3/8-16
UNC
Max.
Coupling
Spline to
3/8-16 UNC
31,7
Coupling
18,7
[.74]
Deep
18,7 [.74] Deep
3/8-16 UNC
Fit ANSI
[1.250]
Spline
toB92.1 1976
3/8-16 UNC
31,7
Flat Root Side Fit 17 Tooth 18,7 [.74] Deep
18,7 [.74] Deep
Dia.
53,1 [2.09]
51,8 [2.04]
Fit
ANSI
B92.1 1976
[1.250]
12/24
Spline
Max.
Max. Coupling
Dia.
53,1 [2.09]
51,8 [2.04]
Coupling
12/24 Spline
Max.
Max. Coupling
Coupling
C-2-16
4000 Compact Series
radial load capacity on the
motor shafts) at various
kg [1000 lb].
Note:
94 kg/7 Bar [208 lb/100 PSI].
Thrust Load
Standard Mount- All shaft options 1-1/4 inch and larger
[lb]
kg
[9000]
4000
[8000]
[7000]
[6000]
[5000]
[4000]
[3000]
3500
3000
2500
2000
1500
[2000]
1000
[1000]
500
0
0
mm -80 -60 -40 -20 0 20 40 60 80 100 120 140
[inch] [-3] [-2] [-1]
0
[1]
Max. Axial Loads
454 kg [1000 lb]
below.
RPM
50
1.23
100
200
300
400
500
600
700
800
1.00
0.81
0.72
0.66
0.62
0.58
0.56
0.54
For 3,000,000 shaft revolutions or 500 hours —
Increase these shaft loads
52%.
[2]
[3]
[4]
C-2
[5]
Mounting Surface
Wheel Mount- All shaft options 1-1/4 inch and larger
[lb]
kg
[9000]
4000
[8000]
[7000]
[6000]
[5000]
[4000]
[3000]
3500
3000
2500
2000
1500
[2000]
1000
[1000]
500
0
0
mm -80 -60 -40 -20 0 20 40 60 80 100 120 140
[inch] [-3] [-2] [-1]
0
[1]
[2]
[3]
[4]
[5]
Mounting Surface
C-2-17
4000 Compact Series
Char-Lynn 4000 Compact
Series motors are durable
and have long life as long
as the recommended case
Allowable case pressure
is highest at low shaft
speeds. Consequently,
motor life will be shortened
if case pressure exceeds
these ratings (acceptability
may vary with application).
limitation charts.
150
[2000]
100
[1500]
Case
Pressure
Bar
50
[PSI]
[1000]
0
Optional
[ 500]
0
0
Case Drain
Required
Optional
0
100 200 300 400 500 600 700 800 900
Speed RPM
All Shaft options 1-1/4 inch and smaller.
[2000]
[1500]
100
Case
Pressure
Bar
50
[PSI]
0
Optional
[1000]
[ 500]
0
0
Optional
0
100 200 300 400 500 600 700 800 900
Speed RPM
All Shaft options larger than 1-1/4 inch.
C-2-18
Case Drain
Required
4000 Compact Series
Dimensions
Ports
7/8-14 O-ring Ports (2)
17º
11,9 [.47]
48,6
[1.91]
Max.
94,8
[3.73]
Max.
6,9/3,8
[.27/.15] 48,6
[1.91]
17º Max.
27,2/25,9
[1.07/1.02]
7/16-20 UNF O-ring
or G 1/4 (BSP)
6,9/3,8
Case Drain Port
[.27/.15]
11,9 [.47]
Port B 27,2/25,9
[1.07/1.02]
Port A
25,4 [1.00]
57,7 [2.27]
Max.
94,8
[3.73]
Max.
18,1/16,5
7/16-20 UNF O-ring
[.71/.65]
or G 1/4 (BSP)
Case Drain Port
56,9 [2.24]
Max.
Port B
65,02 [2.560]
35,56
[1.400]
Port B —
16,3/15,4
25,4 [1.00]
[.64/.61] Dia.
Port A —
13,3/12,1 [.52/.48] Dia.
Port A — B Port
15,8/14,2
13,3/12,1 [.52/.48] Dia.[.62/.56]
A Port
56,9 [2.24]
Max.
B Port
Port O-ring15,8/14,2
7/16-20BUNF
Case Drain Port [.62/.56]
A Port
7/16-2057,2
UNF O-ring
6,9/3,8
Case Drain
[2.25]Port
[.27/.15]
Max.
17º
56,9 [2.24]
Max.
B Port
57,2 [2.25]
Max.
6,9/3,8 57,2
[2.25]
47,8 [1.88]
Max.
7/16-20 UNF O-ring
or G 1/4 18,1/16,5
(BSP)
Case Drain
Port
[.71/.65]
22,1 [.870]
11,58
47,50 [1.870] [.456]
38,10 [1.500]
23,9
47,8 [1.88]
[.94]
Max.
56,9 [2.24]
Max.18,1/16,5
[.71/.65]
65,02 [2.560]
Port B —
3/8-16 UNC
15,7
35,56
16,3/15,4
[.62] Deep
(3) or Dia.
[1.400]
[.64/.61]
M10 x 1.5 - 6H (3)
38,10 [1.500]
23,9
[.94]
57,7 [2.27]
Max.
11,58
[.456]
Manifold Mount
56,6 [2.23]
Max.
3/8-16 UNC 15,7
[.62] Deep (3) or
M10 x 1.5 - 6H (3)
22,1 [.870]
47,50 [1.870]
56,9 [2.24]
Max.
7/16-20 UNF O-ring
or G 1/4 (BSP)
Case Drain Port
56,6 [2.23]
Max.
47,8 [1.88]
Max.
A Port
60,0 [2.35]
Max.
C-2
18,1/16,5
[.71/.65]
Port A
56,9 [2.24]
Max.
56,9 [2.24]
Max.
22,05
[.868]
21,59
[.850]
47,8 [1.88]
Max.
A Port
13,34
EATON
Low Speed High Torque Motors
[.525]
21,59
60,0 [2.35]
22,05
[.868]
56,9 [2.24]
Max.
E-MOLO-MC001-E6 September 2011
57,2 [2.25] Max.
C-2-19
4000 Compact Series
65,02 [2.560]
65,02 [2.560]
Port B — Port B —
35,56 35,56
16,3/15,416,3/15,4
[1.400] [1.400]
[.64/.61] Dia.
[.64/.61] Dia.
Dimensions
11,58
[.456]
Ports
Port A —Port A —
13,3/12,113,3/12,1
[.52/.48] Dia.
[.52/.48] Dia.
23,9
[.94]
11,58
[.456]
3/8-16 UNC
3/8-16
15,7UNC 15,7
[.62] Deep[.62]
(3) or
Deep (3) or
M10 x 1.5M10
- 6Hx(3)
1.5 - 6H (3)
38,10 [1.500]
38,10 [1.500]
1-1/16-12 O-ring Ports (2)
Positioned 180 Apart
18,1/16,518,1/16,5
[.71/.65] [.71/.65]
22,1 [.870]22,1 [.870]
47,50 [1.870]
47,50 [1.870]
56,6 [2.23]56,6 [2.23]
Max.
Max.56,9 [2.24]56,9 [2.24]
7/8-14 O-ring End Ports
Max. (2)Max.
B Port
B Port
15,8/14,215,8/14,2
[.62/.56] [.62/.56]
A Port A Port
23,9
[.94]
7/16-20 UNF
7/16-20
O-ring
UNF O-ring
Case Drain
Case
PortDrain Port
47,8 [1.88]47,8 [1.88]
Max.
Max.
56,9 [2.24]56,9 [2.24]
Max.
Max.
B Port B Port
47,8 [1.88]47,8 [1.88]
Max.
Max.
A Port
21,59
57,2
57,2 60,0 [2.35]60,0 [2.35]
6,9/3,8 6,9/3,8
[2.25] [2.25] Max.
[.27/.15] [.27/.15]
Max. [.850]
Max.
Max.
17º
17º
57,2 [2.25]57,2 [2.25]
Max.
Max.
A Port
C-2-20
7/16-20 UNF
7/16-20
O-ring
UNF O-ring
or G 1/4 (BSP)
or G 1/4 (BSP)
Case Drain
Case
PortDrain Port
A Port
13,34
[.525]
A Port
56,9 [2.24]56,9 [2.24]
Max.
22,05Max.
[.868]
21,59
[.850]
13,34
[.525]
50,80 50,80
[2.000] [2.000]
22,05
[.868]
57,2 [2.25]57,2
Max.
[2.25] Max.
B Port B Port
7/16-20 UNF-2B
7/16-20O-ring
UNF-2B O-ring
Case
PortDrain Port
59,0 [2.32]59,0
Max.
[2.32] Max. Case Drain
4000 Compact Series
Dimensions
Ports with Shuttle
7/8-14 O-ring Ports (2)
11,9 [.47]
Back-Pressure Relief
27,2/25,9
[1.07/1.02]
Valv e
Port B
17,5
[.689]
Port A
25,4 [1.00]
57,7 [2.27]
Max.
Case Drain*
62,5 [2.46]
Max. Shuttle Location
with shuttle and back pressure
relief valve for closed loop
applications.
48,6 [1.91] Max.
15,9 [.625]
94,8 [3.73]
Max.
C-2
Case Drain*
50.0º *Case Drain
7/16-20 UNF-2B
O-ring Port
50,80
[2.000]
Min.
7/8-14 O-ring End Ports (2)
Back-Pressure
Relief Valv e
7/16-20 UNF O-ring
Case Drain Port
with shuttle and back pressure
relief valve for closed loop
applications.
47,8 [1.88]
Max.
62,5 [2.46]
Max.
53,1/47,8
[2.09/1.88]
13,34 [.525]
59,0 [2.32] Max.
22,05 [.868]
A Port
Shuttle Location
21,59
[.850]
B Port
50,80
[2.000]
C-2-21
4000 Compact
Series
The following 24-digit coding system has been developed to identify all of the configuration
options for the 4000 Compact Series motor. Use this model code to specify a motor with the
Model Code
ADK
* *
* *
* *
* *
1 2 3
4 5
6 7
8 9
10 11
1 , 2 , 3 Product Series
ADK – 4000 Compact
Series Motor
4 , 5 Displacement
cm3/r [in3/r]
10 – 160 [ 9.8]
12 – 200 [12.3]
15 – 250 [15.4]
20 – 325 [19.8]
25 – 405 [24.6]
30 – 490 [29.8]
6 , 7 Mounting Type
AB – 4 Bolt (Wheel) 108,0
[4.25] Pilot Dia. and 13,59
[.535] Dia. Mounting
Holes on 147,6 [5.81] Dia.
B.C. 127,0 [5.00] Dia. Rear
Mount Pilot
AC – 2 Bolt SAE A (Std.)
82,5 [3.25] Pilot Dia and
13,59 [.535] Dia. Mtg. Holes
on 106,4 [4.19] Dia. B.C.
AE – 4 Bolt (Bearingless)
101,6 [4.00] Pilot Dia. and
13,59 [.535] Dia. Mounting
Holes on 127,0 [5.00] Dia.
B.C.
AF – 2 Bolt SAE B (Std.)
14,35 [.565] Dia. Mtg.
Holes on 146,0 [5.75] Dia.
B.C.
AH – 4 Bolt (Standard) 82,5
[.535] Dia. Mounting Holes
on 106,4 [4.19] Dia. B.C.
AJ – 4 Bolt Magneto (Std.)
13,59 [.535] Dia. Mtg. Holes
on 106,4 [4.19] Dia. B.C.
2,79 [.110] Pilot Length
AP – 4 Bolt (wheel
compatible for Hayes Brake)
13,59 [.535] Dia. Mounting
Holes on 147,6 [5.81] Dia.
B.C. with Turned Down
Housing to 88,9 [3.50] Dia.
AG – 4 Bolt (Wheel - Short)
91.9 [3.62] Pilot Dia. 14.35
[.565] Dia. Holes on 147.6
[5.81] Dia. Bolt Circle with
O-ring Groove
C-2-22
* *
*
0 0
* *
* *
*
12 13 14
15 16
17 18
19 20
21
AT – 2 Bolt (Standard)
101.6 [4.00] Pilot Dia. 13.59
[.535] Dia. Holes on 146.0
(Similar to SAE B)
BB* – 4 Bolt (SAE B)
(Standard) 101,6 [4.00] Pilot
Dia. and 14,7 [.58] Dia.
Mounting Slots on 127,0
BE* – 4 Bolt (Wheel) 139,7
[5.50] Front and Rear Pilot
Dia. and 13,49 [.531] Dia.
Mounting Holes on 165,1
BG* – 4 Bolt (Wheel-Short)
127,0 [5.00] Front and Rear
Pilot Dia. and 13,59 [.535]
Dia. Mounting Holes on
147,62 [5.812] Dia. Bolt Circle
8 , 9 Output Shaft
02 – 1 1/4 inch Dia. Straight
with 3 /8 -16 Thread in end,
7,938 [.3125] Sq. x 31,75
03 – 1 1/4 inch Dia. .125 :
1 Tapered Shaft Per SAE
J501 with 1-20 UNEF -2A
Threaded Shaft end, and
slotted Hex Nut, 7,938
[.3125] Sq. x 25,40 [1.000]
Straight Key
04 – 31.75 [1.250] Dia. Flat
Root Side Fit, 14 tooth,
12/24 DP 30° Involute
Spline with .375-16
UNC-2B Thread in End,
33.0 [1.30] Minimum Full
Spline Length
06 – 1 1/4 inch Dia. Splined
14T with 38,1 [1.50] Min.
Full Spline Length and
53,1 [2.09] Max. Coupling
Length
08 – 40 mm Dia. Straight
(with Straight Key) M12 x
1,75 - 6H Thread in end
10 – 32 mm dia. Straight
(with Straight Key) M8 x
1,25 -6H Thread in end, and
56,4 [2.22] Max. Coupling
Length
11 – 1 1/2 inch Dia. Straight
(with Straight Key) 3 /8 -16
Thread in end
17 – 28.22 [1.111] Dia. Flat
Root Side Fit, 17 Tooth,
Spline, 28.58 [1.125]
Minimum Full Spline
Length
98 – 1 5/8 inch Dia. Tapered
with Straight Key and 1
1/4 ‑18 UNEF Slotted Hex.
Nut
99 – 1 1/2 inch Dia. Splined
17T with 31,2 [1.23] Min. Full
Spline Length
10 , 11 Ports
AA – 7/8 -14 UNF –2B SAE
O-ring (Staggered)
AB – 12,70 [.500] and 15,88
[.625] Dia. Ports (Manifold)
and 3x 3 /8 -16 UNC Port
Block Mounting Holes
AD – 7/8 -14 UNF –2B SAE
O-ring (End Ports)
AE – 12,70 [.500] and 15,88
[.625] Dia. Ports (Manifold)
and 3 x M10 x 1,5-6H Port
Block Mounting Holes
AG – G 1/2 BSP Straight
Thread ports (Staggered)
AH – 1 1/16 - 12 UN-2B
O-Ring ports (Positioned
180° Apart)
AJ – .750-16 UNF-2B
SAE O-ring Ports – Ports
Oriented 180° to each
other
BA– .875-14 UNF-2B SAE
O-ring Ports – Port B
Recessed 11.4 [.45] from
Port A – End Ports – Cast
Boss Removed
00 – None
01 – 7/16 -20 UNF –2B SAE
O-ring Port (Case Drain)
02 – G 1/4 (BSP) Straight
Thread Port (Case Drain)
* These mounting options are available with
shaft options 08, 11, 98 and 99.
*
0
A
22 23
24
Valve with G 1/4 (BSP)
Straight Thread Port (Case
Drain)
14 Back-Pressure
Relief Valve
0 – None
A – Set at 4,5 bar [65 PSI]
(for Manual Pumps)
15 , 16 Valve Options
00 – None
17 , 18 Accessories
00 – None
AA – Seal Guard
AF – M12 Threaded
Connector Digital Speed
Sensor (Two 30 Pulse per
rev. signals in quadrature)
AG – M12 Threaded
Connector Digital Speed
Sensor (One 60 Pulse per
rev. speed signal and one
directional signal)
(Hardware)
00 – None
01 – Viton Seals
21 Special Features
(Assembly)
0 – None
A – Flange Rotated 90°
B – Reverse Rotation
22 Paint/ Special
Packaging
0 – No Paint, Individual
Box
A – Low Gloss Black
23 Eaton Assigned Code
when Applicable
0 – None
24 Eaton Assigned
Design Code
A – First Code
Feature in bold are preferred and
allow for shorter lead time.
Delta Series
Features:
• Excellent reliability with
time proven Char-Lynn
components
Highlights
• Proven disc valve technology with the highest efficiencies in its class
• Leak resistant motor with
the front bearing protecting the shaft seal
• Torque up to 10,500 lb-in
intermittant duty / Flow
up to 30 GPM intermittant
• 12 displacements available
from 6.9 to 46 CID
• Shaft sizes up to 1-5/8
inch
• 3-1/4 inch front pilot and
5 inch rear pilot
• STC ports available
Benefits:
Description
This wheel motor is the latest addition to the Char
Lynn product line. The Delta motor provides torques
up to 11,500 in-lbs. Eaton has packed this motor
with many “best in class” features: the optimized
geroler profile ensures smooth operation; the disc
valve technology has the best performance and the
bearing capacity is the highest in the industry for very
demanding applications.
Delta Series
Geroler Element
Flow l/min [GPM]
Speed RPM
Pressure bar [PSI]
Torque Nm [lb-in]
Parker is a registered trademark of Parker
Intangibles LLC.
12 Displacements
670 Cont.**
837 Inter.*
200 [3000] Cont.**
275 [4000] Inter.*
1015 [9000] Cont**.
1185 [10500] Inter.*
• Perfect replacement
for Parker® TF-TG and
WhiteTM RE motors
• Lowest no load pressure
drop which leads to longer
life and lower temperature
operation
• Highest overall efficiency:
more available HP to the
system than competitive
motors
• The highest side load
capacity with 4,500 lbs
at 3” from the mount
face
Applications:
• Scissor Lift
• Boom Lift
• Industrial Sweeper
• Mower
**Continuous— (Cont.) Continuous rating, motor may be run continuously at these ratings.
White is a trademark of White Drive
Products, Inc.
Boom Lift
Sweeper
Mower
C-3-1
C-3
Delta Series
Specifications
Delta Series motors
Displ. cm3/r (in3/rev)113 [6.9]
Max Speed
Continuous
668
(RPM)Intermittent
831
@Flow
Flow
Continuous75 [20]
l/min [GPM] Intermittent95 [25]
Torque
Continuous320 [2834]
Nm [lb-in]
Intermittent417 [3697]
Pressure
Continuous 205 [3000]
∆ bar [∆ PSI] Intermittent 275 [4000]
Weight
12,7 [28.0]
kg [lb]
146 [8.9] 198 [12.1] 234 [14.3] 252 [15.4] 300 [18.3] 347 [21.2] 395 [24.1] 470 [28.7] 542 [33.1] 649 [39.6] 754 [46.0]
519382323300252 218 192 161 140 117 100
778516485450379 327 288 241 209 175 151
Note:
Top assure best motor life, run motor
for approximately one hour at 30% of
rated pressure belore application to
full load. Be sure motor is filled with
fluid prior to any load applications.
When pressurizing B port, all displacements have a continuous rating
of 2000 psi.
310 bars (4500 PSI)
Do not exeed ∆ pressure rating
(see chart above).
C-3-2
75 [20]
115 [30]
429 [3800]
563 [4984]
205 [3000]
275 [4000]
12,9 [28.5]
75 [20]
115 [30]
554 [4904]
725 [6421]
205 [3000]
275 [4000]
13,8 [30.5]
75 [20]
115 [30]
651 [5763]
852 [7543]
205 [3000]
275 [4000]
14,3 [31.5]
75 [20]
115 [30]
712 [6311]
930 [8236]
205 [3000]
275 [4000]
15,0 [33.0]
75 [20]
75 [20]
75 [20]
75 [20]
115 [30]
115 [30]
115 [30]
115 [30]
844 [7472] 933 [8260] 972 [8607] 1039 [9199]
1087 [9629] 1208 [10698]1206 [10684]1222 [10824]
205 [3000] 205 [3000] 190 [2750] 170 [2500]
275 [4000] 275 [4000] 240 [3500] 205 [3000]
15,0 [33.0] 15,4 [34.0] 16,1 [35.5] 16,8 [37.0]
Recommended Fluids:
Premium quality, anti wear type
hydrauli coil with a viscosity of
no less than 70 SUS at operating
temperature.
75 [20]
75 [20]
115 [30]
115 [30]
994 [8809] 1028 [9102]
1202 [10644] 1253 [11100]
140 [2000] 120 [1750]
170 [2500] 155 [2250]
17,5 [38.5] 18,4 [40.5]
Recommended System
Operating Temp.:
-34°C to 82°C [-30°F to
180°F]
Per ISO cleanliness Code 4406:
20/18/13
75 [20]
115 [30]
985 [8721]
1232 [10910]
105 [1500]
140 [2000]
19,1 [42.0]
Delta Series
113 cm3/r [6.9 in3/r]
∆ Pressure Bar [PSI]
in production.
Fl ow LPM [GPM]
Performance Data
Continuous
Intermittent
No operation
17345269 86103121138155172190 207224241259276
25050075010001250150017502000225025002750 30003250350037504000
2 2044506869151140135515931814201821972349 25732776297531823362
235177103129153180205228248265 290313336359380
7.665
64
636260605957565556 5452484944
4 2104577069501194143616771906212923512571 27903010323134543660
245280107135162189215240265290 315340365390413
15 132
131
130129128127126125123122120 118115113112110
6 1964456969421186143216741914214423672587 28053027325234763695
225079106134162189216242267292 317342367392417
23 199
196
196195193192191190189185183 182180177174172
8 1764256779211168142016661906215223862616 28343051326534813697
204876104132160188215243269295 320344369393417
30 266
264
263261261259257257255252250 248246244241237
10 1604076599011149139816501894213423702601 28233044325834573654
184674102130158186214241268294 319344368390413
38 333
333
329326324323321320318314312 309306303301295
12 1343826328761122137216211868211123532589 28213046327034793680
15437199127155183211238266292 319344369393415
45 399
398
396393392389387386383381377 374372370367364
14 1113576088551102135015991847209023302569 28003024325034553614
13406997124152181208236263290 316341367390408
53 466
465
462460457455453451449446442 438436433429415
16 813255778221071132115721817206323072549 27813011323734363578
9376593121149177205233260288 314340365388404
61 533
532
529527524522520517516513509 506503500496477
18 482955437901036128315351781202722712512 27512984321434313597
5336189117145173201229256284 311337363387406
68 601
600
597593591587586583581577573 570568564559542
20 142635107581005124914991746198822312474 27122945317633953597
2305886113141169197224252279 306332359383406
76 668
666
664661658654652649646644640 637634630628621
22228477725 972121814681712195722012447 26862917314933503523
265482110138166193221249276 303329355378398
83
733
731728724721718715713710705 704700697688664
25170416663 913115314021646189121362382 26222856308132733452
194775103130158186214241269 296322348369390
95
831
829827825821818815812809805 803800794776745
301144297551076140017252047236826873003 33233635394242494552
134885122158195231267303339 375410445480514
114
778
777773770765759756753749746 744742740737735
114 Torque [lb-in]
13Nm
778
Speed RPM
Fl ow LPM [GPM]
}
146 cm3/r [8.9 in3/r]
∆ Pressure Bar [PSI]
17345269 86103121138155172190 207224241259276
25050075010001250150017502000225025002750 30003250350037504000
2 28859690711841445171819922247253728103039 32903595384639964265
3267
102134163194225254286317343 371406434451482
7.650
48
464244434039383736 3432312528
4 28961994712671593191422272482275530423295 36153916413544564680
3370
107143180216251280311343372 408442467503528
15102
100
989695959493918884 8179767470
6 27560493412591588190822322552286931813497 38004102439746804955
3168
105142179215252288324359395 429463496528559
23 154
151
149148146145144143141137135 133130128125123
8 25658090912351566188722092528284531603475 37834091439746924984
2966
103139177213249285321357392 427462496530563
30 206
204
201200198198196195190187185 182179179176173
10 22755387912041535186121842504282031333447 37574061436946674963
266299136173210247283318354389 424459493527560
38 258
256
253251250249248246241238236 233231229228225
12 19952185011721501182521482469278030913402 37144017432446274922
235996132170206243279314349384 419454488522556
45 310
308
305303301300299297292290287 284282281278276
14 15748080911301458178421042426274330573369 36793983429145934892
185491128165201238274310345380 415450484519552
53 362
360
356354353352351346344341339 337335332331329
16 13245778011021429175320812397271430253335 36453947425545584857
155288124161198235271306342377 412446480515548
61 414
412
408406405403402398395392389 387384382380377
18 9841474210651390171520392360267529863295 36053906421345184817
114784120157194230266302337372 407441476510544
68 467
465
461459457456453450447444442 439437435432430
20 4237370010201347167019892308262829443255 35683866417244754774
54279115152189225261297332368 403436471505539
76 519
517
514511509507503500498495492 489488485484482
22 163286599781306162819502268258629003211 35223823412844294732
23774110147184220256292327362 398432466500534
83 571
569
565562559559555552549546544 541538536534531
252535768991221154418642179250028113120 34333736403643374639
2965102138174210246282317352 388422456490524
95
647
645641639637633629626624621 618616613612609
301144297551076140017252047236826873003 33233635394242494552
134885122158195231267303339 375410445480514
114
778
777773770765759756753749746 744742740737735
C-3-3
C-3
Delta Series
198 cm3/r [12.1 in3/r]
Fl ow LPM [GPM]
Performance Data
17345269 86103121138155172190 207224241259276
25050075010001250150017502000225025002750 30003250350037504000
2 313732
111314801870224926683059344738224189 45444875519455085948
3583
126167211254301345389432473 513550586622671
7.636
35
343231302927272624 2221181718
4 367809
122816402038243728443234362340104398 47795164554559176275
4191
139185230275321365409453497 540583626668708
1575
74
727169686765636261 5856565452
6 365799
123116542066247328783270366540564446 48335215559859756347
4190
139187233279325369414458502 546589632675717
23
112
111
110
109
107
106
104
1021019998 9695939189
8 343782
121916482069248428983300370240934482 48655237560759766349
3988
138186234280327373418462506 549591633675717
30151
150
149147146145143142140138135 134133131129127
10 322759
120116332063248329043316372641254515 49045290567260486421
3686
136184233280328374421466510 554597640683725
38190
188
187186185182181178177174173 171169168166164
12 283719
115815902020244828683279369140964492 48835265564460156385
3281
131180228276324370417462507 551594637679721
45229
227
226224223221220218216215212 211209206205202
14 238671
111015381970239628163228364440504451 48465231561359826357
2776
125174222271318364411457503 547591634675718
53267
266
264262261259257255253251249 246244242240238
16 191625
106314931923234527683182359640034403 48015191557659476316
2271
120169217265312359406452497 542586630671713
61305
304
303301300298296295293291289 287285284281279
18 139567
100614381871229927203133354739564359 47605128549258716247
1664
114162211260307354400447492 537579620663705
68342
341
340339337335333331330328326 324322321319317
20 9945788613151745216825903006341838224224 46225018541858166208
1152
100148197245292339386432477 522567612657701
76382
380
378377375373371369366364362 359358356354352
22 1538381012431676209625202938335137594161 45584953533957226095
24391140189237284332378424470 515559603646688
83420
417
416415413411409407405403401 399397395392390
2527270011311559198524082823323136394042 44434842522956175992
3179128176224272319365411456 502547590634677
95
476
475474472470468466465463461 459457455453450
3016360010371474190223152723313435363933 43384737512555165899
1868117166215261307354399444 490535579623666
114
516
506494487484488494501506511 514515516515514
163
Torque lb-in
18Nm
516
Speed RPM
Fl ow LPM [GPM]
}
C-3-4
234 cm3/r [14.3 in3/r]
17345269 86103121138155172190 207224241259276
25050075010001250150017502000225025002750 30003250350037504000
2 470971
145719212414287733483821427547305164 56305997644668637217
53
110
164217273325378431483534583 636677728775815
7.631
30
292826252525242322 2119201915
4 468988
150419892482296434473916438448435302 57636213666871137543
53
112
170225280335389442495547599 651701753803852
15 64
62
616059585756565555 5452515048
6 449966
148419802470295334453922439748515304 57506197664370857524
51
109
168224279333389443496548599 649700750800849
23 96
95
939292919089888888 8786868483
8 416931
144619542458294834383909438148355280 57146150658470157445
47
105
163221277333388441495546596 645694743792841
30 129
128
126125124123123121121120120 119119118117116
10 380896
141019172425291934123890437348315280 57166148658670177452
43
101
159216274330385439494545596 645694744792841
38 161
160
158157156155154153153152151 150149148147146
12 341856
136618762384288033703843431947825229 56656102653769627392
3997
154212269325380434488540590 640689738786835
45 194
193
191190189188187186185185184 183182181180178
14 290804
131218132320282133153793426847325181 56236057648569077327
3391
148205262318374428482534585 635684732780827
53 226
225
224222221220219218217216216 215214212211209
16 239743
124917562264275932553735420746695122 55686004643268457268
2784
141198256312367422475527578 629678726773820
61 258
258
257255254253252251251250249 247246245244242
18 176688
118716942203269831953676414646035055 54975930635867747194
2078
134191249305361415468520571 621669718765812
68 291
291
289287286285284283282281279 278277276276275
20 108614
112116232124262031183603407745414990 54305865630167207139
1269
127183240296352407460513563 613662711759806
76 323
323
322320319317317316314312311 310310310309309
22 28535
108115822082257930713550401844834943 54065855630067237139
360
122179235291347401454506558 610661711759806
83 355
355
355352351350349348345343342 341341341341341
2541095614601959245429413419389243564806 52515683611765316939
46
108165221277332386439492543 593642691737783
95
404
404402401399398397394392391 390390389390389
3017170012971735222627183204368941624623 50795519595963776781
1979146196251307362417470522 573623673720766
114
485
485485483481480478476474472 472471471471471
Delta Series
252 cm3/r [15.4 in3/r]
Fl ow LPM [GPM]
Performance Data
17345269 86103121138155172190 207224241259276
25050075010001250150017502000225025002750 30003250350037504000
2 485
1011
152020322564305935694065456150855589 60546536689173887872
55
114
172229289345403459515574631 683738778834889
7.628
27
262625242323222323 2222191920
4 504
1062
160921452684321337444263478052945804 63116811730877878236
57
120
182242303363423481540598655 712769825879930
15 59
57
565655555454535353 5151494947
6 478
1031
158521322670319537174222472652225721 62116700717976588118
54
116
179241301361420477534590646 701756810865917
23 89
88
868585848484848483 8282807878
8 453
1012
157121152664319137174224472552155706 61946678716176288076
51
114
177239301360420477533589644 699754808861912
30 120
118
117115114113113112113113113 112111110109108
10 398957
151620632609313736684181467851575636 61166589705975227974
45
108
171233295354414472528582636 690744797849900
38 149
148
147145144143142142142143142 142141140139138
12 370914
146820112557308536144125462251025577 60596538701774977966
42
103
166227289348408466522576630 684738792846899
45 180
179
178176174173172172172172172 172171171170169
14 290842
139919482496302435524065457150565525 59876445690573597813
3395
158220282341401459516571624 676728780831882
53 210
209
208206205203202201200199199 200200200200199
16 239795
134618912434296234944003451149955461 59196382684172927743
2790
152213275334395452509564616 668720772823874
61 240
240
238237235233232231229228229 230230230230230
18 157716
126518102355288134083921443149245401 58606310674971847627
1881
143204266325385443500556610 662712762811861
68 270
270
269267265264261261258256256 258259260260260
20 96650
120317502294282033453857436648655340 58016242668671227553
1173
136198259318378435493549603 655705755804853
76 300
300
299297295293292289287286286 287289290291290
22 26569
111116562195272532503763426847695259 57336182660970307459
364
125187248308367425482538594 647698746794842
83 330
330
330328327324322320316314313 314316318320320
2542596715082042257430933605411046025084 55616028648268997316
48
109170231291349407464520574 628681732779826
95
375
375374372369366364361358357 356358361364364
3017972312661800233028523364386843684856 53385811626967017096
2082143203263322380437493548 603656708757801
114
450
450450449447443439436433430 430431434437438
179
Torque lb-in
20Nm
450
Speed RPM
Fl ow LPM [GPM]
}
300 cm3/r [18.3 in3/r]
17345269 86103121138155172190 207224241259276
25050075010001250150017502000225025002750 30003250350037504000
2 608
1257
191925533196382444755087570763076901 74728015848489629413
69
142
217288361432505574644712779 8449059581012
1063
7.624
23
232221212120191817 1615131111
4 612
1283
194025873227385644835094569362936881 74628024857491139629
69
145
219292364435506575643710777 8429069681029
1087
15 50
48
474645444444434241 4040393837
6 570
1248
190625473178380044205025561962036773 73457899844989929525
64
141
215288359429499567634700765 8298929541015
1075
23 76
74
737170696868696868 6766656463
8 540
1210
187125223152378144045008560761866749 73197879843389779512
61
137
211285356427497565633698762 8268909521013
1074
30101
100
989694939292929393 9393929191
10 496
1161
182524713110373343624968557461576721 72747811835688879416
56
131
206279351421492561629695759 8218829431003
1063
38 126
126
124122120118115113113113114 116118118117117
12 443
1108
176824183059368843074918552661146681 72397786833888769411
50
125
200273345416486555624690754 8178799411002
1062
45 151
151
150148145143141140139139140 142144144144144
14 387
1034
170123462985361042274839545260506622 71847723826988169362
44
117
192265337408477546615683748 811872934995
1057
53 177
177
176173171168166165163163165 167169171170170
16 366961
162022642903353041474753536659606540 70987642816986859211
41
109
183256328399468537606673738 801863922980
1040
61 202
202
201199197195192190189188188 189191194196196
18 291893
154621872829345040674678528358736451 70057537806485809103
33
101
175247319390459528596663728 791851910969
1028
68 227
227
227224222219217215213211212 214217220221221
20 204797
144420942736336139744585518457756353 69077448797484898992
2390
163236309380449518585652717 780841900958
1015
76 252
252
252251249246243241239238238 239242245247248
22 102710
136620132651327038854496509656896271 68317362787783758880
1280
154227299369439508575642708 771831889945
1003
83 278
278
278277274272269267265264263 265269273275275
25553
120818512489311437264335493055236108 66707220778382988777
62
136209281352421489557624690 753815879937991
95
316
316316313310307303301299298 298301306310312
3023394115392179281134304028462552175802 63856957752280608565
26
106174246317387455522589655 721785849910967
114
379
379379377374371367365363362 361364368374376
C-3
C-3-5
Delta Series
347 cm3/r [21.2 in3/r]
Continuous
Intermittent
No operation
Fl ow LPM [GPM]
Performance Data
17345269 86103121138155172190 207224241259276
25050075010001250150017502000225025002750 30003250350037504000
2 687
1415
212828243532424849475633629869647575 8182874392099624
10081
78
160
240319399480558636711786855 92498710401087
1138
7.620
19
181817181717161514 1312 9 8 4
4 689
1443
217928913606430249865653631669657615 82608891951510120
10698
78163246326 407486 563 638 713 786 860 9331004107411431208
15 42
41
414039373838393838 3737353331
6 648
1406
215428663580427649705641629069217563 81908812942710029
10630
73
159
243324404483561637710781854 92599510641132
1200
23 64
64
636160585757596060 5958575655
8 606
1356
210528253545424149435621627468997522 8144876893889998
10598
68
153
238319400479558635708779849 91999010601129
1196
30 87
86
858482817978798182 8181807877
10 550
1295
204127653488418848915585626468997505 8091867292839885
10488
62
146
230312394473552631707779847 91397910481116
1184
38 109
108
107106104103100 98 97 98100 103103103102101
12 478
1227
197626983411410848025479614667827396 7992858591769767
10345
54
139
223305385464542619694766835 90296910361103
1168
45 131
130
130129127125122119117115115 119123125125124
14 409
1151
189626243344404847425418608367227339 7939854191429738
10318
46
130
214296378457535612687759829 89696410321099
1165
53 153
153
152152149147145142140139139 143147148147147
16 339
1033
177424943209390746055280595666107243 7850843890149592
10166
38
117
200282362441520596672746818 88695310181083
1148
61 174
174
174174172169166164162159159 160165168170170
18 245943
167624013113380945005175583764777107 7711830888959466
10040
28
106
189271351430508584659731802 87193810041069
1133
68 196
196
196195193192189187185183181 182185188192193
20 143832
157122903003369743865050571563516968 75698147872192979855
1694
177259339417495570645717787 8559209851050
1113
76 218
218
218218216214212209207205203 203205210214215
22 34715
145421752896359442804950560262366854 74498027859091509705
481
164246327406483559632704774 8419069701033
1096
83 240
240
240240240238236233230228226 226228231237240
25523
125119692693339540814756541460576687 72967882845790119534
59
141222304383461537611684755 8248909551017
1076
95
272
272272272272269266263261259 259261265270272
30152
107217492434312338024468511457636400 70187633823288198997
17
121197275353429504577651723 792862929996
1016
114
327
327327327327323319315314313 315319323327327
}
Fl ow LPM [GPM]
152 Torque lb-in
17Nm
327 Speed RPM
C-3-6
395 cm3/r [24.1 in3/r]
17345269 86103121138155172190 207224241
25050075010001250150017502000225025002750 300032503500
2 782
1622
243632374034483756506428721379118607 9235979810439
88
183
275365455546638726814893972104311061179
7.618
17
171616161716151515 141312
4 770
1643
247632874088486056176357710378388566 9285999010684
87
186
280371462549634718802885967104811281206
15 38
37
363533333536363535 343433
6 746
1609
246032804083486756446384710378118520 9232993010616
84
182
278370461549637721802882962104211211199
23 58
57
555452515051535455 545353
8 699
1561
243032494062485256386398712678208506 9198988410565
79
176
274367459548637722805883960103811161193
30 77
76
757472706867697274 747473
10 630
1489
234531804008481956226397714278568525 9142977610438
71
168
265359453544635722806887962103211041178
38 96
96
959391908785838388 939393
12 556
1412
226430903898468954736225697677108415 9081968110304
63
159
256349440529618703788870950102510931163
45 115
115
115113111109107105102100100 105110113
14 469
1325
217829993819461153916137686775818270 8942959810234
53
150
246339431521609693775856934101010841155
53 134
134
134133131128126124122120119 123133134
16 360
1220
206928943715450652906048678274958190 8873953410181
41
138
234327419509597683766846925100210761149
61 153
153
153153151148145143140138138 139145151
18 334
1098
195127773591438651725924666573878087 8763941810048
38
124
220314405495584669752834913 98910631134
68 173
173
173173171169166162161159157 158162169
20 221993
183726603479425950305780651872387939 861392589892
25
112
207300393481568653736817896 97210451117
76 192
192
192192191189186183181179177 178182188
22 115862
169825213337413548955641636670677752 841490629702
1397
192285377467553637719798875 95010231095
83 211
211
211211211209206203201200199 200204209
25
637
147322963117390946875434616368617536 819288299475
72
166259352441529613696775851 9259971070
95
240
240240240238235232229227227 228233240
30
211
107919032725352643115079582465477240 792185779228
24
122215308398487573658739817 8949681042
114 288
288288288286283280277274273 275280287
Delta Series
470 cm3/r [28.7 in3/r]
Intermittent
No operation
17345269 86103121138155172190 207
25050075010001250150017502000225025002750 3000
2 925
1885
28203727463955266404727081298978979410551
104213318 421 524 624 723 821 918 1014 1106 1191
7.614
14
13
12
12
12
11
10998 7
4 94219422917 3849 4776 5692 6594 7488 8352 9199 10014 10824
106219329 435 539 643 744 845 943 1039 1131 1222
15 31
30
292928272726252423 23
6 906
1921
28923833477256766572744083099152997410786
102217327 433 539 641 742 840 938 1033 1126 1218
23 47
46
454544434342424141 40
8 856
1866
28533795473056346520737982309075989510693
97211322 428 534 636 736 833 929 1025 1117 1207
30 63
62
626160585757585857 56
10 780
1799
28003745468555946479733781779009984310638
88203316 423 529 632 731 828 923 1017 1111 1201
38 79
79
787776757472727474 74
12 699
1709
27113661459755086403725881018916971910506
79193306 413 519 622 723 819 915 1007 1097 1186
45 96
95
949392919089899090 91
14 596
1612
26093561449053906268711279418743951910282
67182295 402 507 608 708 803 897 987 1075 1161
53 112
111
111110109107106104103101102 104
16 467
1486
24803440437152686152699278108601937010118
53168280 388 493 595 695 789 882 971 1058 1142
61 129
128
127126125123122120119117116 116
18 332
1353
23573317425651576043689277138501927010026
37153266 375 481 582 682 778 871 960 1047 1132
68 145
145
144143142140138136135134132 133
20 304
1226
221831724102499458736731755783659147 9922
34138250 358 463 564 663 760 853 944 1033 1120
76 161
161
160159158157155153152150149 150
22 137
1059
204830043945484057276576739981988967 9715
15120231 339 445 546 647 742 835 926 1012 1097
83 177
177
177176175174172170169167166 166
25833
181627653680457554556313713379288691 9436
94
2053124155176167138058959811065
95
201
201201200198196194193191191 192
30491
131822953232414250225881672175228300 9320
55
1492593654685676647598499371052
114
241
241241241240237236236233232 227
}
491 Torque lb-in
55Nm
241 Speed RPM
Fl ow LPM [GPM]
Continuous
Fl ow LPM [GPM]
Performance Data
542 cm3/r [33.1 in3/r]
173452 69 86103121138 155 172
250 500 7501000 12501500 1750 2000 2250 2500
2 113123043433 4558 5668 6725 7732 8683 9645 10457
128260388 515 640 759 873 980 1089 1181
7.6 131211 11 11 11 10 8 8 7
4 113923523515 4638 5735 6781 7819 8809 9752 10644
129266397 524 648 766 883 994 1101 1202
15 272625 25 25 25 24 23 23 22
6 106322673433 4549 5645 6694 7697 8675 9630 10557
120256388 514 637 756 869 979 1087 1192
23 414039 38 38 38 39 38 37 36
8 99221863354 4475 5578 6646 7665 8608 9535 10449
112247379 505 630 750 865 972 1076 1180
30 565554 53 52 52 51 52 52 51
10 89720903259 4378 5482 6555 7602 8578 9482 10343
101236368 494 619 740 858 968 1071 1168
38 706968 67 67 65 64 64 64 65
12 80719803138 4256 5365 6440 7494 8481 9403 10275
45 91224354 481 606 727 846 957 1062 1160
848383 81 80 79 78 77 76 77
14 69318733028 4138 5218 6268 7318 8304 9235 10105
78211342 467 589 708 826 937 1043 1141
53 989897 96 95 93 91 90 91 92
16 55417322882 3993 5083 6107 7118 8089 9032 9928
63196325 451 574 689 804 913 1020 1121
61 112112111 110 109 108 106 104 104 106
18 40915822738 3844 4924 5952 6956 7928 8874 9772
46179309 434 556 672 785 895 1002 1103
68 126126126 125 124 123 121 119 119 121
20 35514282587 3696 4767 5804 6813 7786 8732 9624
40161292 417 538 655 769 879 986 1087
76 140140140 139 138 137 136 134 134 135
22 31012592412 3518 4595 5619 6618 7589 8536 9438
35142272 397 519 634 747 857 964 1065
83 154154154 154 152 151 150 148 148 149
25 95821073215 42815310 6305 7264 8204 9110
108238 363 483 599 712 820 926 1029
95174174 174 174 173 171 170 168 169
30 52115992696 37694804 5809 6776 7705 8617
59181304 425542 656 765 870 973
114209209 209 209 208 207 207 205 205
C-3
C-3-7
Delta Series
649 cm3/r [39.6 in3/r]
Continuous
Fl ow LPM [GPM]
Performance Data
Intermittent
No operation
173452 69 86103121138 155
250 500 7501000 12501500 1750 2000 2250
2 136527874156 5488 6775 7949 910210174 11100
154315469 620 765 89710281149 1253
7.6 101010 9 9 8 7 6 3
4 132627704113 5400 6632 7819 897310030 11015
150313464 610 749 88310131132 1244
15 222221 20 21 20 19 19 18
6 125826633998 5270 6521 7692 8774 9808 10809
142301451 595 736 868 9911107 1220
23 353433 32 32 32 32 32 31
8 115425583902 5195 6455 7659 8775 9770 10708
130289441 587 729 865 9911103 1209
30 474645 44 42 42 42 43 43
10 104524423787 5076 6331 7541 8691 9685 10573
118276428 573 715 851 9811093 1194
38 585857 56 55 53 53 54 55
12 92823213662 4939 6193 7385 8536 9577 10469
105262413 558 699 834 9641081 1182
45 707070 68 67 66 65 65 66
14 74021273469 4746 5989 7188 8352 9433 10439
84240392 536 676 812 9431065 1179
53 828282 81 80 79 77 76 76
16 61419903318 4588 5795 6942 8081 9154 10141
69225375 518 654 784 9121033 1145
61 939393 93 92 91 90 89 90
18 44818303158 4414 5619 6754 7853 8890 9873
51207356 498 634 763 8871004 1115
68 105105105 105 104 103 102 102 104
20 28116182944 4198 5410 6551 7653 8689 9676
32183332 474 611 740 864 981 1092
76 117117117 117 117 116 114 114 115
22 27615182842 4099 5313 6453 7554 8596 9576
31171321 463 600 728 853 970 1081
83 128128128 128 128 128 126 125 126
2510792393 3646 4834 5969 7071 8112 9105
122270 412 546 674 798 916 1028
95146146 146 146 146 145 144 144
30 43617473013 42255356 6454 7489 8479
49197340 477605 729 845 957
114175175 175 175 175 174 174 175
Fl ow LPM [GPM]
754 cm3/r [46.0 in3/r]
C-3-8
173452 69 86103121138
250 500 7501000 12501500 1750 2000
2 156131284605 6014 7422 8721 997810910
176353520 679 838 98511271232
7.6 988 8 7 7 6 5
4 154831424650 6029 7350 8605 978510892
175355525 681 830 97111051230
15 191818 18 18 18 17 17
6 147030844608 6022 7346 8555 972210850
166348520 680 829 96610981225
23 302928 27 27 27 27 27
8 135929754504 5925 7263 8488 963810694
153336509 669 820 95810881207
30 403938 38 37 36 37 38
10 124028444364 5815 7185 8458 960310584
140321493 656 811 95510841195
38 505049 48 47 46 46 47
12 107926864207 5641 7008 8248 939010400
122303475 637 791 93110601174
45 606060 59 58 57 57 57
14 93225124038 5477 6850 8124 927410286
105284456 618 773 91710471161
53 707070 70 69 68 67 67
16 75323283834 5246 6577 7831 899910040
85263433 592 742 88410161133
61 808080 80 80 79 78 78
18 54721193632 5024 6320 7551 8706 9721
62239410 567 714 852 9831097
68 909090 90 90 90 90 90
20 31019193430 4826 6126 7339 8466 9430
35217387 545 692 829 9561065
76 100100100 100 100 100 100 100
22 24816663172 4571 5878 7102 8254 9269
28188358 516 664 802 9321046
83 110110110 110 110 110 110 110
25
126127844191 55046727 7873 8911
142314473 621759 8891006
95
126126126 126126 126 126
30
54520553474 48006036 7175 8231
62232392 542681 810 929
114
151151151 151151 151 151
}
8479 Torque lb-in
957Nm
175
Speed RPM
Delta Series
Ports
Dimensions
G
Wheel Mount
Port A Pressurized — CCW
Port B Pressurized — CW
7/8 -14
Ø126.95±0.05/-0.08
[4.998±.002/-.003]
1/2
UNF-2B SAE O-ring Ports
(BSP) Ports
14.0±0.3
[.55±.01]
Port - A
46.7 [1.84] Max.
50.8±1.0
[2.00±.04]
Ø82.50±0.05/-0.08
[3.248±.002/-.003]
Port - B
135.9
[3.53] Max.
70.1
[2.76] Max.
2X 19.0±0.8
[.75±.03]
36.8±0.3
[1.45±.01]
70.1
[2.76] Max.
135.9
[5.35] Max.
C-3
147.64
[5.8125]
Dia Bolt Circle
4X Ø13.59±0.25 Thru
[.535±.010]
4X R13.2 Min [.52]
Displacement X
code
max
code
max
069
089
121
143
154
183
212
241
287
331
396
460
156.5 [6.16]
162.6 [6.40]
172.5 [6.79]
181.9 [7.16]
195.6 [7.70]
209.0 [8.23]
130.6 [5.14]
135.9 [5.35]
144.3 [5.68]
150.4 [5.92]
153.2 [6.03]
150.4 [5.92]
C-3-9
Delta Series
Ports
Dimensions
G
Standard Mount
Port A Pressurized — CCW
Port B Pressurized — CW
7/8 -14
1/2
UNF-2B SAE O-ring Ports
(BSP) Ports
50,3
[1.98] Max.
Port - A
2.54±0.25
[.100±.010]
52.5
[2.07] Max.
50.8±1.0
[2.00±.04]
103,1
[4.06] Max.
134,9
[5.31] Max.
Port - B
45˚
X
22.5˚
106.38
[4.18]
Dia Bolt Circle
70.3
[2.77] Max.
6X Ø13.59±0.25 Thru
[.535+.010]
Displacement X
code
max
code
max
069
089
121
143
154
183
212
241
287
331
396
460
199.8 [7.87]
206.0 [8.11]
215.8 [8.50]
225.1 [8.86]
238.8 [9.40]
252.3 [9.93]
C-3-10
173.8 [6.84]
179.7 [7.08]
187.7 [7.39]
193.7 [7.63]
196.5 [7.74]
193.7 [7.63]
Ø82.50±0.05/-0.08
[3.248±.002/-.003]
19.56±0.25 Pilot Dia
[.770±.010]
2X 62.5±1.0
[2.46±.04]
Delta Series
Dimensions
Shafts
Mounting Surface
4,95/4,61
[.194/.181]
63.53/61.53
[2.502/2.422]
1½ Inch Straight
9,551/9,525
[.3760/.3750]
38,9/37,3
[1.53/1.47]
Standard Mount
Wheel Mount
60.3/60.1
[2.40/2.34]
38.1/38.0
[1.53/1.47]
Dia.
3/8 -16 UNC-2B
18,8 [.74] Deep
Full THD
106.3/106.1
[4.21/4.15]
Mounting Surface
Mounting Surface
1¼ Inch 14 Tooth
Splined
52.1/50.8
[2.05/2.00]
33.0 [1.30]
MIN FULL
Spline
Standard Mount
31,75 [1.250] Dia.
Wheel Mount
96.1/94.5
[3.78/3.72]
Spline to fit
ANSI B92.1 1976
Flat Root Side Fit
14 Tooth
14/24 Spline
C-3
C-3
3/8 -16 UNC-2B
19,0 [.75] Deep
Mounting Surface
Mounting Surface
1¼ Inch Tapered
64.0/62.4
[2.51/2.45]
25,4
[1.00]
4,1 [.16]
Dia. Thru
7,963/7,937
[.3135/.3125]
Sq. Key
Standard Mount
31,78/31,72
[1.251/1.249] Dia.
Wheel Mount
13,00/12,4
[.51/.49]
94.1/92.5
[3.78/3.72]
3,95/3,61
[.155/.143]
1-20 UNEF-2A
1.5:12 Ratio
Standard Taper
Shaft End
Per SAE J501
Mounting Surface
EATON
EATON
Char-Lynn
Low Speed
Low Speed
High Torque
High Torque
Motors
Motors
E-MOLO-MC001-E6
E-MOLO-MC001-E5
September
June 2009
2011
C-3-11
Delta Series
Shaft Side Load
Capacity
Todetermineradialloadat
speedsotherthan100RPM,
below.
RPM
50
100
200
300
400
500
600
700
800
1.23
1.00
0.81
0.72
0.66
0.62
0.58
0.56
0.54
Side Load Chart for Standard Mount
Allowable Radial Load, Delta Motor
L10 Bearing Life per ISO 281
12000
10000
Radial Load (lbs)
Thesecurvesindicatethe
motor shaft(s) at various
locations.
3 Million Revolutions
8000
6000
4000
2000
0
-4
-3
-2
1
0
1
2
3
4
Distance from Standard Mount Flange (inches)
Side Load Chart for Wheel Mount
Allowable Radial Load, Delta Motor
L10 Bearing Life per ISO 281
12000
Radial Load (lbs)
10000
8000
6000
4000
2000
0
-3
-2
-1
0
1
2
3
4
5
Distance from Wheel Mount Flange (inches)
C-3-12
EATON Low
EATON
Char-Lynn
Speed Low
HighSpeed
TorqueHigh
Motors
Torque
E-MOLO-MC001-E6
Motors E-MOLO-MC001-E5
September June
2011 2009
6
Delta Series
Note:
ForDeltaSeriesMotorswith
in the charts below contact
your Eaton Representative.
Product Numbers
Mounting
Wheel
Motor
Shaft
Port Size
1-1/4 Inch
Tapered
1-1/2 Inch
17 T Splined
7/8” O-ring
1-1/4 Inch
Tapered
1-1/2 Inch
17 T Splined
7/8” O-ring
1-1/4 Inch
Tapered
1-1/2 Inch
17 T Splined
7/8” O-ring
7/8” O-ring
7/8” O-ring
7/8” O-ring
Timing
Standard -CCW
Standard -CW
Standard -CCW
Standard -CW
Standard -CCW
Standard -CW
Standard -CCW
Standard -CW
Standard -CCW
Standard -CW
Standard -CCW
Standard -CW
Displacement cm3/ r [in3/ r] / Product Number
113
[6.9]
184-0005-0012
184-0025-0012
184-0013-0012
184-0037-0012
252
[15.4]
184-0003-0012
184-0029-0012
184-0017-0012
184-0041-0012
470
[28.7]
184-0009-0012
184-0033-0012
184-0021-0012
184-0045-0012
146
[8.9]
184-0006-0012
184-0026-0012
184-0014-0012
184-0038-0012
300
[18.3]
184-0004-0012
184-0030-0012
184-0018-0012
184-0042-0012
542
[33.1]
184-0010-0012
184-0034-0012
184-0022-0012
184-0046-0012
198
[12.1]
184-0002-0012
184-0027-0012
184-0015-0012
184-0039-0012
347
[21.2]
184-0007-0012
184-0031-0012
184-0019-0012
184-0043-0012
649
[39.6]
184-0011-0012
184-0035-0012
184-0023-0012
184-0047-0012
234
[14.3]
184-0001-0012
184-0028-0012
184-0016-0012
184-0040-0012
395
[24.1]
184-0008-0012
184-0032-0012
184-0020-0012
184-0044-0012
754
[46.0]
184-0012-0012
184-0036-0012
184-0024-0012
184-0048-0012
C-3
C-3
EATON
EATON
Char-Lynn
Low Speed
Low Speed
High Torque
High Torque
Motors
Motors
E-MOLO-MC001-E6
E-MOLO-MC001-E5
September
June 2009
2011
C-3-13
Delta Series
The following 26-digit coding system has been developed
to identify all of the configuration options for the Delta Low
Speed High Torque motor. Use this model code to specify a
motor with the desired features. All 26 digits of the code must
be present when ordering. You may want to photocopy the
matrix below to ensure that each number is entered in the
correct box.
Model Code
M
D L
1
2 3
* * *
4 5
6
* *
* *
* *
0
*
*
0 0
0 0
* *
* *
7 8
9 10
11 12
13
14
15
16 17
18 19
20 21
22 23
1 Product
M – Motor
2 , 3 Series
DL – Delta Series
cm3/r [in3/r]
069 – 113 [ 6.9]
089 – 146 [ 8.9]
121 – 198 [12.1]
143 – 234 [14.3]
154 – 252 [15.4]
183 – 300 [18.3]
212 – 347 [21.2]
241 – 395 [24.1]
287 – 470 [28.7]
331 – 542 [33.1]
396 – 649 [39.6]
460 – 754 [46.0]
7 , 8 Mounting Type
AA – Wheel, 4 Bolt: 82.6
[3.25] Pilot Dia. 13.59
[.535] Dia. Holes On
147.6 [5.81] Dia. Bolt
Circle. 127.0 [5.00] Dia.
Rear Mount Pilot
AB – Standard, 6 Bolt:
82.6 [3.25] Pilot Dia.
13.59 [.535] Dia. Holes
on 106.4 [4.19] Dia.
Bolt Circle. .100 [2.54]
Pilot Length. Sae A,
Magneto
[3.25] Pilot Dia. 13.59
[.535] Dia. Holes on
106.4 [4.19] Dia. Bolt
Circle. .250 [6.35]
Pilot Length. SAE A,
Magneto
9 , 10 Output Shaft
01 – 38.10 [1.500] Dia.
Straight with .375-16
UNC-2B Thread, and
9.52 [.375] Sq x 25.40
02 – 31.75 [1.250] Dia.
.125:1 Tapered Shaft
per SAE J501 with
1.000-20 UNEF-2A
Threaded Shaft End
and Slotted Hex Nut,
7.938 [.3125] Sq x
25.40 [1.000] Straight
Key
03 – 41.30 [1.626] Dia. .125:1
J501 with 1.250-18
UNEF-2A Threaded
Shaft End and Slotted
Hex Nut, 11.125 [.4380]
Sq x 34.04 [1.340]
Straight Key
04 – 31.75 [1.250] Dia.
Flat Root Side Fit, 14
Tooth, 12/24 DP 30
Deg. Involute Spline
with .375-16 UNC-2B
Thread in End, 33.0
[1.30] Minimum Full
Spline Length
05 – 38.10 [1.500] Dia. Flat
12/24 DP 30 Deg.
Involute Spline, 31.8
[1.25] Minimum Full
Spline Length, with
.375-16 UNC-2B Thread
in End
06 – 38.10 [1.500] Dia.
J501 with 1.000-20
UNEF-2A Thread in End,
7.938 [.3125] Sq x 31.75
[1.250] Key
11 , 12 Ports
AA – .875-14 UNF-2B SAE
O-Ring
AC – G 1/2 BSP Straight
Thread
13 Pressure/Flow Option
0 – None
14 Geroler Option
0 – Standard
B – Tight Fitting Geroler
15 Seal Option
0 – Standard
1 – Viton
4 – Seal Guard
0 0
A
24 25 26
AA - No Paint, Individual
Box
AB -Low Gloss Black
AC - Epoxy Coated (Frost
Gray), Individual Box
AE - No Paint, Bulk Box
AF - Low Gloss Black Primer,
Bulk Box
24 , 25 Customer
Identification
00 – None
26 Design Code
B – Two (2)
16 , 17 Accessories
00 – None
Special Features
(Hardware)
00 – None
18 , 19
(Assembly)
00 – Standard Rotation CCW
01 – Standard Rotation CW
C-3-14
4000 Series
Features
• 10 displacements, a variety of mounting flanges
and output shafts
Highlights
• Reliable, proven design
• High efficiency
• Environmental protection
options
Benefits
• Flexiblilty in designing this
motor into a system
• Options that fit well into
tough applications
Applications
• Mowing
• Snow Removal
• Sprayer
• Trencher
• Wood Products
Description
The 4000 Series offers up to 8600 in-lb of torque and
25 gpm (continuous ratings). This is the corner stone
of the Char-Lynn line.
4000 Series Motors
Geroler Element
Flow l/min [GPM]
Speed RPM
Pressure bar [PSI]
Torque Nm [lb-in]
10 Displacements
722 Cont.**
868 Inter.*
200 [3000] Cont.**
300 [4500] Inter.*
970 [8600] Cont.**
1180 [10450] Inter.*
C-4
**Continuous— (Cont.) Continuous rating, motor may be run continuously at these ratings
Mowing
Snow Removal
Sprayer
Trencher
C-4-1
4000 Series
Specifications
4000 Series Motors
110 [ 6.7]
130 [ 7.9]
160 [ 9.9]
205 [12.5]
245 [15.0]
280 [17.1]
310 [19.0]
395 [24.0]
495 [30.0]
625 [38.0]
Max. Speed Continuous
(RPM) Intermittent
@ Flow
Flow
Continuous
l/min [GPM] Intermittent
Torque*
Continuous
Nm [lb-in] Intermittent
Pressure Continuous
∆ bar
Intermittent
[∆ PSI]
Peak
697 868 722 862 582 693 459 546 383 532 336
488
303 422 239 376 191 305 151 241
Weight
kg [lb]
75 [20]
95 [25]
95 [25]
95 [25]
95 [25]
95 [25]
95 [25] 115 [30] 115 [30] 115 [30] 130 [35] 130 [35]
320 [2850] 375 [3330] 485 [4290] 600 [5300] 705 [6240] 753 [6666]
470 [4160] 560 [4940] 705 [6240] 800 [7100] 845 [7470] 957 [8471]
205 [3000] 205 [3000] 205 [3000] 205 [3000] 205 [3000] 205 [3000]
310 [4500] 310 [4500] 310 [4500] 260 [3750] 310 [4500] 260 [3750]
310 [4500] 310 [4500] 310 [4500] 310 [4500] 310 [4500] 310 [4500]
95 [25]
95 [25]
95 [25]
95 [25]
130 [35] 150 [40] 150 [40] 150 [40] .
850 [7530] 930 [ 8240] 945 [ 8375] 970 [ 8605]
1065 [9420] 1185 [10470] 1170 [10350] 1180 [10450]
205 [3000] 190 [2750] 140 [2000] 115 [1700]
260 [3750] 240 [3500] 170 [2500] 140 [2000]
310 [4500] 295 [4250] 230 [3300] 180 [2600]
Standard or 17.9 [39.5] 18.1 [40.0] 18.1 [40.0] 18.4 [40.5] 18.6 [41.0] 19.1 [42.0] 19.5 [43.0] 20.4 [45.0]
Wheel Mount
Bearingless 14.1 [31.0] 14.3 [31.5] 14.1 [31.0] 14.5 [32.0] 14.7 [32.5] 15.2 [33.5] 15.6 [34.5] 16.6 [36.5]
21.8 [48.0]
23.1 [51.0]
17.9 [39.5]
19.3 [ [42.5]
*See shaft torque ratings for limitations..
Note:
load applications.
310 bar [4500 PSI]
∆ bar [∆ PSI] :
outlet port
Continuous Rating:
10% of every minute
Peak Operation:
1% of every minute
C-4-2
Recommended Fluids:
Recommended System
Operating Temp.:
-34°C to 82°C [-30°F to
180°F]
4406: 20/18/13
4000 Series
110 c3m/r [6.3/7r ]in
[250]
155
Performance Data
[.5]
1,9
in production.
[1]
3,8
[2]
7,5
[4]
15
[6]
23
[8]
30
Continuous
Flow LPM [GPM]
[10 ]
Peak
Intermittent
38
[12 ]
45
[14 ]
53
[16 ]
No Operation
61
[18 ]
68
[20]
130 c3m/r [7.3/9r ]in
[.5]
1,9
[1]
3,8
[2]
7,5
[4]
15
[6]
23
[8]
30
Flow LPM [GPM]
[10 ]
38
[12 ]
45
[14 ]
53
[16 ]
61
[18 ]
68
[20]
76
[22]
83
[25]
95
[30]
114
76
[250]
155
[500]
35
[1000]
70
[1500]
105
[2000]
140
[2500]
170
[3000]
205
[3500]
240
[310]
35
12
[290]
35
30
[280]
30
57
[260]
30
116
[240]
25
173
[230]
25
228
[210]
25
283
[200]
25
341
[180]
20
400
[160]
20
457
[130]
15
516
[110]
10
574
[70]
10
633
[50]
5
722
[510]
60
9
[530]
60
28
[530]
60
56
[520]
60
114
[510]
60
170
[510]
60
225
[510]
60
225
[500]
55
338
[490]
55
396
[490]
55
453
[480]
55
511
[470]
55
569
[450]
50
628
[430]
50
718
[400]
45
862
[1060]
120
5
[1080]
120
25
[1100]
125
53
[1100]
125
111
[1100]
125
167
[1080]
120
222
[1080]
120
278
[1070]
120
335
[1060]
120
392
[1050]
120
449
[1050]
120
506
[1040]
120
564
[1020]
115
624
[1000]
115
714
[940]
105
855
[1590]
180
2
[1600]
180
19
[1620]
185
47
[1650]
185
105
[1650]
185
161
[1640]
185
216
[1640]
185
272
[1640]
185
329
[1640]
185
386
[1630]
185
443
[1630]
185
500
[1620]
185
559
[1610]
18 0
615
[1580]
180
702
[1500]
170
842
[2110]
240
14
[2140]
240
42
[2200]
250
100
[2200]
250
156
[2210]
250
210
[2210]
250
266
[2220]
250
323
[2220]
250
380
[2220]
250
437
[2220]
250
494
[2210]
250
551
[2190]
24 5
606
[2160]
245
690
[2080]
235
827
[2640]
300
13
[2660]
300
40
[2700]
305
95
[2720]
305
149
[2740]
310
202
[2750]
310
256
[2750]
310
312
[2750]
310
368
[2760]
310
424
[2760]
310
480
[2760]
310
536
[2750]
310
590
[2720]
305
672
[2670]
300
806
[3060]
34 5
12
[3180]
360
38
[3210]
365
90
[3240]
36 5
142
[3270]
370
194
[3300]
375
246
[3300]
375
300
[3310]
375
355
[3310]
375
410
[3320]
375
465
[3330]
375
520
[3320]
375
573
[3300]
375
653
[3200]
360
783
[3450]
390
4
[3600]
405
29
[3660]
415
70
[3710]
420
123
[3770]
425
176
[3820]
430
229
[3840]
435
282
[3860]
435
335
[3860]
435
388
[3870]
435
442
[3890]
440
495
[3880]
440
547
[3860]
435
625
[3740]
425
749
[4000]
275
[4500]
310
[500] [1000] [1500] [2000] [2500] [3000] [3500] [4000] [4500]
35
70
105
140
170
205
240
275
310
[150]
15
14
[170]
20
34
[180]
20
68
[190]
20
138
[200]
25
207
[190]
20
277
[180]
20
347
[160]
20
417
[140]
15
487
[130]
15
556
[100]
10
626
[390]
45
10
[440]
50
33
[450]
50
67
[460]
50
136
[470]
55
204
[460]
50
274
[460]
50
344
[450]
50
414
[440]
50
484
[440]
50
553
[440]
50
622
[850]
95
5
[900]
100
31
[910]
105
62
[940]
105
123
[960]
110
200
[950]
105
270
[950]
105
340
[940]
105
410
[930]
105
480
[920]
105
549
[910]
105
618
[80]
10
697
[430]
50
694
[900] [1370] [1860] [2350] [2850] [3320] [3790] [4160]
100
155
210
265
320
375
430
470
690
677
664
638
611
579
545
518
[1290]
145
2
[1380]
155
28
[1390]
155
56
[1400]
160
110
[1420]
160
193
[1420]
160
262
[1420]
160
331
[1420]
160
400
[1420]
160
469
[1410]
160
537
[1400]
160
606
[1860]
210
25
[1860]
210
50
[1870]
210
97
[1880]
210
184
[1880]
210
253
[1890]
215
322
[1880]
210
390
[1880]
210
458
[1870]
210
525
[1870]
210
593
[2270]
255
22
[2280]
260
44
[2310]
260
84
[2320]
260
174
[2340]
265
241
[2350]
265
308
[2350]
265
374
[2350]
265
440
[2350]
265
505
[2350]
265
570
[2680]
305
18
[2700]
305
36
[2730]
310
70
[2760]
310
163
[2790]
315
228
[2820]
320
292
[2820]
320
355
[2830]
320
419
[2840]
320
482
[2840]
320
545
[3110]
350
11
[3120]
355
28
[3140]
355
56
[3200]
360
150
[3230]
365
213
[3260]
370
274
[3260]
370
335
[3280]
370
446
[3300]
375
455
[3300]
375
516
[3880]
440
28
[3950]
455
121
[4010]
455
179
[4070]
460
236
[4080]
460
292
[4110]
465
348
[4120]
465
404
[4140]
465
460
[25]
95
[378 0]
425
69 0
[4020]
455
20
[4100]
465
50
[4180]
470
104
[4270]
480
158
[4350]
490
212
[4370]
495
263
[4390]
495
366
[4400]
495
366
[4420]
500
418
[4440]
500
470
[4440]
500
520
[4430]
500
595
[3450]
390
18
[3560]
400
42
[3640]
410
136
[3670]
415
196
[3700]
420
255
[3710]
420
313
[3730]
420
471
[3750]
425
428
[3770]
425
485
}
Torque [lb-in ]
Nm
Speed RPM
[4080]
460
12
[4560]
515
37
[4660]
525
91
[4750]
535
145
[4840]
545
189
[4870]
550
237
[4890]
550
286
[4920]
555
335
[4940]
560
384
C-4
C-4-3
4000 Series
160 cm3/r [9.9 in3/r]
Performance Data
[.5]
in production.
1,9
[1]
Flow LPM [GPM]
3,8
[2]
7,5
[4]
15
[6]
23
[8]
30
[ 10 ]
38
[ 12 ]
45
[ 14 ]
Continuous
Peak
Intermittent
53
[ 16 ]
61
[ 18 ]
No Operation
68
[20]
76
[22]
205 cm3/r [12.5 in3/r]
[.5]
1,9
[1]
Flow LPM [GPM]
3,8
[2]
7,5
[4]
15
[6]
23
[8]
30
[ 10 ]
38
[ 12 ]
45
[ 14 ]
53
[ 16 ]
61
[ 18 ]
68
[20]
76
[22]
83
[25]
95
[30]
11 4
C-4-4
[250]
15
[500]
35
[1000]
70
[400]
45
8
[410]
45
17
[420]
45
36
[430]
50
73
[430]
50
107
[410]
45
144
[390]
45
182
[350]
40
217
[330]
35
256
[290]
35
291
[270]
30
329
[230]
25
366
[810]
90
5
[830]
95
17
[850]
95
35
[870]
100
73
[880]
100
106
[870]
100
143
[860]
95
180
[850]
95
216
[840]
95
254
[820]
95
290
[810]
90
327
[800]
90
364
[1500]
170
1
[1590]
180
16
[1680]
190
34
[1770]
200
71
[1800]
205
105
[1820]
205
142
[1820]
205
179
[1810]
205
215
[1790]
200
252
[1770]
200
289
[1750]
200
325
[1730]
195
362
[3860]
435
12
[4060]
460
27
[4260]
480
61
[4370]
495
98
[4410]
500
132
[4460]
505
166
[4440]
500
200
[4430]
500
237
[4410]
500
272
[4400]
495
308
[4380]
495
345
[4560]
515
11
[4800]
540
25
[5040]
570
57
[5170]
585
90
[5240]
590
125
[5300]
600
160
[5300]
600
194
[5290]
600
229
[5280]
595
264
[5270]
595
298
[5270]
595
334
[190]
20
402
[150]
15
459
[780] [1690] [2600] [3500] [4370]
90
190
295
395
495
400
398
394
389
380
[750] [1640] [2560] [3480] [4360]
85
185
290
395
495
456
453
448
442
434
[710] [1540] [2510] [3350] [4190]
80
380
475
175
285
546
529
520
542
537
[5260]
595
368
[5240]
590
421
[5030]
570
504
[1500] [2000] [2500] [3000]
205
105
140
170
83
[25]
[3500] [4000]
240
275
[4500]
310
95
[30]
11 4
[2220]
250
15
[2410]
270
32
[2590]
295
70
[2620]
295
103
[2660]
300
138
[2700]
305
174
[2690]
305
211
[2670]
300
248
[2650]
300
284
[2640]
300
321
[2620]
295
358
[2860]
325
14
[3140]
355
29
[3140]
385
68
[3530]
400
101
[3560]
400
136
[3580]
405
170
[3570]
405
202
[3560]
400
243
[3540]
400
280
[3520]
400
316
[3510]
395
353
[5390] [5510]
625
610
3
9
[5420] [6000]
610
680
22
16
[5730] [6340]
645
715
45
35
[5900] [6590]
665
745
81
74
[6020] [6770]
765
680
109
116
[6110] [6890]
780
690
143
152
[6120]
690
185
[6120]
690
219
[6120]
690
253
[6120]
690
287
[6120]
690
321
[250]
15
[500] [1000] [1500]
35
70
10 5
[2000]
14 0
[300]
35
8
[320]
35
23
[330]
35
46
[320]
35
93
[300]
35
137
[280]
30
184
[260]
30
232
[240]
25
277
[220]
25
321
[680] [1320] [2050]
150
230
75
5
3
7
[700] [1350] [2070]
80
155
235
22
20
19
[700] [1360] [2080]
80
155
235
45
41
40
[710] [1400] [2100]
80
160
240
92
90
88
[710] [1420] [2140]
80
160
240
135
134
131
[720] [1450] [2180]
80
16 5
245
182
180
176
[720] [1480] [2220]
80
165
250
229
226
221
[700] [1450] [2190]
80
165
245
274
272
266
[680] [1420] [2160]
75
160
245
3 18
319
311
[670] [1400] [2130]
160
75
240
364
362
356
[650] [1360] [2100]
155
75
235
409
407
401
[630] [1340] [2070]
70
150
235
458
456
448
[2750]
3 10
1
[2780]
315
18
[2790]
315
37
[2820]
320
84
[2850]
320
126
[2900]
330
171
[2950]
335
216
[2920]
330
260
[2890]
325
304
[2860]
325
348
[2830]
320
392
[2800]
315
440
[200]
25
366
[180]
20
410
[150]
15
460
[120]
15
509
[70]
10
582
[3300]
375
16
[3340]
375
32
[3420]
385
76
[3510]
395
120
[3560]
400
163
[3610]
410
206
[3590]
405
250
[3570]
405
294
[3550]
400
338
[3530]
400
382
[3510]
395
429
[620] [1330] [2060] [2790] [3500]
70
150
235
315
395
506
502
494
484
473
[600] [1320] [2050] [2780] [3480]
70
150
230
315
395
578
573
563
552
540
[560] [1280] [1990] [2700] [3430]
65
305
390
145
225
693
661
647
687
675
[1990]
225
675
[6210]
700
8
[6740]
760
23
[7100]
800
65
[2500] [3000] [3500]
17 0
205
240
}
Torque [lb-in]
Nm
Speed RPM
[3940]
445
15
[3970]
450
29
[4020]
455
73
[4180]
470
114
[4230]
480
154
[4290]
485
194
[4280]
485
238
[4270]
480
282
[4260]
480
326
[4250]
480
370
[4240]
480
417
[4410]
500
8
[4530]
5 10
27
[4620]
520
62
[4760]
540
90
[4850]
550
138
[4920]
555
182
[4920]
555
224
[4920]
555
266
[4920]
555
308
[4910]
555
350
[4910]
555
396
[4000]
275
[4500]
3 10
[4950]
560
2
[5090]
575
25
[5220]
590
51
[5340]
605
75
[5470]
620
122
[5560]
630
169
[5570]
630
209
[5580]
630
249
[5590]
630
289
[5600]
635
329
[5610]
635
373
[5590]
630
13
[5730]
645
35
[5870]
665
57
[6010]
680
100
[6160]
695
142
[6180]
700
182
[6200]
700
222
[6220]
705
262
[6240]
705
302
[4220] [4910] [5600]
475
555
635
461
438
413
[4210] [4900] [5590]
475
555
630
526
501
474
[3970] [4640]
450
525
630
600
4000 Series
245 cm3/r [15.0 in3/r]
[250]
15
Performance Data
[.5]
1,9
[1]
in production.
Flow LPM [GPM]
3,8
[2]
7,5
[4]
15
[6]
23
[8]
30
[ 10 ]
38
[ 12 ]
45
[ 14 ]
53
[ 16 ]
Continuous
61
[ 18 ]
Peak
68
[20]
Intermittent
No Operation
76
[22]
83
[25]
95
[30]
[.5]
1,9
[1]
Flow LPM [GPM]
3,8
[2]
7,5
[4]
15
[6]
23
[8]
30
[ 10 ]
38
[ 12 ]
45
[ 14 ]
53
[ 16 ]
61
[ 18 ]
68
[20]
76
[22]
83
[25]
95
[30]
11 4
[35]
132
[500]
35
[750]
50
[1000]
70
[1250]
85
[1500]
105
[1750]
120
[2000]
140
[2250]
155
[2500] [2750]
170
190
[533]
60
4
[553]
62
12
[568]
64
26
[579]
65
53
[583]
66
79
[573]
65
10 6
[547]
62
134
[527]
60
161
[497]
56
18 7
[472]
53
214
[437]
39
241
[402]
45
268
[1074]
121
2
[1136]
128
12
[ 1146]
130
26
[ 1167]
132
53
[1177]
133
79
[ 167]
13 2
10 6
[ 1146]
130
133
[1126 ]
127
160
[ 1106]
125
187
[ 1096]
12 4
214
[ 1075]
121
241
[ 1055 ]
1119
268
[ 1714 ]
19 4
12
[1740]
197
25
[ 1771]
200
52
[ 1781]
2 01
78
[ 1780]
201
10 5
[1765]
19 9
133
[1745]
19 7
186
[1730]
19 5
18 6
[ 1715 ]
19 4
213
[1690]
19 1
240
[1669]
189
268
[2287]
258
11
[2328]
263
25
[2374]
268
52
[2395]
271
78
[2404]
272
105
[2395]
271
131
[2369]
268
158
[2344]
265
186
[2324]
263
212
[2299]
260
239
[2274 ]
257
267
[2841]
321
11
[2902]
328
24
[2962]
335
51
[2987]
338
77
[3007]
340
104
[2997]
339
131
[2991]
338
157
[2972]
336
185
[2947]
333
2 11
[2917]
330
237
[2898]
327
266
[3394]
384
11
[3461]
391
24
[3557]
402
51
[3601]
407
77
[3610]
408
104
[3629]
410
130
[3609]
408
157
[3585]
405
184
[3565]
403
2 10
[3541]
4 00
236
[3521]
398
264
[3868]
437
10
[3955]
447
23
[4139]
468
50
[4193]
474
76
[4218]
477
102
[4238]
479
129
[4228]
478
156
[421 3 ]
476
18 2
[4203]
475
208
[4188]
473
234
[4178 ]
472
261
[4389]
496
10
[4524]
5 11
22
[4712]
532
49
[4793]
542
74
[4812]
544
101
[4837]
547
127
[4832]
546
154
[481 6 ]
544
18 0
[4811 ]
544
206
[4801]
542
231
[4791]
541
258
[4895]
553
10
[2922]
330
21
[5285]
597
47
[5376 ]
607
72
[5411]
611
99
[5442]
615
126
[5441]
615
152
[5430]
614
17 8
[5420]
612
203
[5400]
6 10
229
[5394]
609
255
[6080]
685
8
[5630]
636
20
[5848]
661
45
[5959]
673
69
[5994]
677
96
[6035]
682
122
[6034]
682
148
[6028]
681
174
[5919 ]
669
19 9
[5919]
669
224
[5851]
661
249
[366] [10 05] [1629]
184
114
41
295
295
296
[301]
[940] [1588]
179
34
10 6
335
336
336
[845] [1480]
167
96
4 01
402
[ 1348]
15 2
468
[2257]
255
294
[2231]
252
334
[2151]
243
4 00
[2057]
232
466
[2856]
323
292
[2825]
319
333
[2759]
312
398
[2623]
296
464
[3480] [4136]
393
467
290
288
[3419] [4086]
386
462
331
328
[3328] [3984]
3 76
450
396
392
[3183] [3883]
360
439
463
457
[5870]
663
6
[6146 ]
694
19
[6395]
722
44
[6521]
737
67
[6556]
741
94
[6601]
746
119
[6586]
74 4
144
[6511 ]
736
170
[6436]
727
19 5
[6362]
719
219
[1000] [1250]
70
85
[1500]
105
[1750]
120
[2970]
335
12
[3050]
345
27
[3130]
355
59
[3160]
355
88
[3150]
355
117
[3150]
355
147
[3140]
355
178
[3130]
355
208
[3120]
355
239
[3110 ]
350
269
[310 0 ]
350
300
[3400]
385
12
[3420]
385
26
[3630]
410
58
[3660]
415
86
[3680]
415
115
[3690]
415
145
[3680]
415
176
[3670]
415
206
[3660]
415
236
[3650]
415
266
[3640]
410
296
[980]
110
2
[990] [1490]
170
110
14
14
[1000] [1520]
115
170
30
29
[1030] [1560]
115
175
61
60
[1040] [1570]
120
175
90
90
[1020] [1560]
115
175
120
121
[1000] [1540]
115
175
151
150
[980] [1530]
175
110
182
180
[960] [1520]
110
170
212
211
[950] [1500]
10 5
170
243
242
[930] [ 1480]
10 5
16 5
2 74
273
[910 ] [1460]
10 5
165
305
304
[1990]
225
13
[2040]
230
29
[2080]
235
60
[2100]
235
89
[2110]
240
119
[2100]
235
148
[2080]
235
179
[2060]
235
210
[2040]
230
241
[2020]
230
272
[2000]
225
303
[2480]
280
13
[2540]
285
28
[2600]
295
59
[2620]
295
88
[2630]
295
118
[2620]
295
148
[2610]
295
178
[2600]
295
209
[2580]
290
240
[2560]
290
270
[2550]
290
302
[310 ]
35
337
[260]
30
383
[870] [1420]
10 0
160
336
335
[820] [1380]
95
155
382
381
[680] [1250]
75
140
457
456
[ 1110 ]
125
532
[1970]
225
334
[1930]
220
380
[1860]
210
455
[1740]
19 5
531
[2500] [3050] [3590]
280
345
405
332
330
326
[2460] [2980] [3540]
280
335
400
378
376
372
[2390] [2900] [3430]
270
330
390
453
450
445
[2270] [2790] [3340]
255
315
375
528
525
519
132
[250]
15
[750]
50
[460]
50
5
[480]
55
14
[500]
55
30
[510]
60
61
[510]
60
91
[500]
55
121
[470]
55
152
[450]
50
183
[420]
45
213
[400]
45
244
[380]
45
275
[350]
40
305
11 4
[35]
280 cm3/r [17.1 in3/r]
[500]
35
[3000] [3250]
205
225
[368]
720
6
[6666]
753
17
[6946]
785
42
[7082]
8 00
66
[7022]
793
92
[7022]
793
115
[6940]
784
141
[6940]
784
166
[3500] [3750]
260
240
[3340]
375
519
}
[2000] [2250] [2500]
170
15
140
[3830]
435
11
[3930]
445
24
[4130]
465
56
[4200]
475
83
[4210]
475
113
[4230]
480
143
[4220]
475
173
[4200]
475
203
[4190]
475
232
[4180]
470
262
[4170]
470
292
[2750] [3000]
190
205
[3250] [3500]
225
240
[3750]
260
[4250]
480
11
[4440]
500
23
[4630]
525
53
[4710]
530
80
[4680]
530
10
[4900]
555
22
[5120]
580
49
[5220]
590
75
[5020]
565
4
[5320] [5740] [6160] [6640] [7150]
750
810
600
650
695
11
20
18
16
14
[5570] [6030] [6480] [6870] [7340]
680
630
730
775
830
44
47
42
39
36
[5690] [6140] [6620] [7050] [7430]
840
695
645
750
795
59
70
72
67
63
[4770]
540
141
[4760]
540
170
[4740]
535
200
[4730]
535
229
[4710]
530
259
[4700]
530
288
[5290]
600
137
[5280]
595
166
[5260]
595
195
[5250]
595
225
[5230]
590
254
[5220]
590
283
[5670]
650
133
[5750]
650
161
[5740]
650
190
[5730]
650
219
[5720]
645
248
[5710]
645
276
[4140] [4680]
465
530
323
319
[4090] [4640]
460
525
369
365
[3960] [4460]
445
505
442
437
[3910] [4400]
440
495
515
509
[6240] [6710] [7140]
705
760
805
129
125
120
[6230] [6700]
705
755
157
152
[6220]
705
185
[6210]
700
213
[620 0]
700
241
[520 0] [5680]
590
640
313
306
[5180]
585
357
[4950]
560
427
Torque [lb-in]
Nm
Speed RPM
[6811 ] [7239] [ 7654]
865
770
818
4
6
5
[7191] [7749] [8323]
813
876
940
17
15
13
[7502] [8020] [8471]
848
906
957
41
40
38
[7607] [8097]
859
915
65
64
[7518]
849
90
[7518]
849
111
C-4
[4756] [5205]
537
588
285
279
[4710] [5205]
532
588
325
314
[4573] [5021]
517
567
389
377
[4354]
492
449
C-4-5
4000 Series
310 cm3/r [19.0 in3/r]
Performance Data
[.5]
1,9
[1]
in production.
Flow LPM [GPM]
3,8
[2]
7,5
[4]
15
[6]
23
[8]
30
[ 10 ]
38
[ 12 ]
45
[ 14 ]
53
[ 16 ]
Continuous
61
[ 18 ]
Peak
68
[20]
Intermittent
No Operation
76
[22]
83
[25]
95
[30]
11 4
[35]
395 cm3/r [24.0 in3/r]
[.5]
1,9
[1]
Flow LPM [GPM]
3,8
[2]
7,5
[4]
15
[6]
23
[8]
30
[ 10 ]
38
[ 12 ]
45
[ 14 ]
53
[ 16 ]
61
[ 18 ]
68
[20]
76
[22]
83
[25]
95
[30]
11 4
[35]
132
[40]
151
C-4-6
[250]
15
[50 0 ]
35
[70 0 ]
80
4
[750]
85
9
[800 ]
90
18
[860]
95
38
[860]
95
57
[840]
95
76
[800]
90
95
[ 760 ]
85
11 4
[ 740 ]
85
133
[710 ]
80
153
[680]
75
17 2
[610 ]
70
19 2
[1340 ]
15 0
2
[1430 ]
16 0
9
[1500]
170
18
[ 1630]
18 5
38
[1690]
19 0
57
[1680]
19 0
76
[1680]
19 0
95
[ 1660 ]
19 0
11 4
[1640 ]
18 5
133
[1620]
185
153
[1600 ]
18 0
1 72
[1580]
18 0
191
[570]
65
2 11
[490]
55
239
[750]
50
[1000] [ 1250] [15 00]
70
85
10 5
132
[1750]
120
[2000]
14 0
[250]
15
[50 0]
35
[600]
70
4
[620]
70
11
[630]
70
23
[640]
70
47
[650]
75
71
[640]
70
96
[620]
70
121
[600]
70
145
[570]
65
169
[540]
60
193
[490]
55
2 17
[450]
50
242
[1150]
130
2
[ 1270]
145
11
[ 1280]
14 5
23
[1290]
14 5
47
[1300]
14 5
71
[1300 ]
14 5
96
[1280]
14 5
120
[1260]
140
144
[ 1240]
14 0
169
[ 1230]
14 0
19 3
[1210 ]
13 5
2 17
[1190]
135
242
[750] [1000]
50
70
[1920]
215
11
[1940]
220
22
[1960]
220
46
[1970]
225
70
[1980]
225
95
[1970]
225
120
[1940]
220
144
[ 1920]
215
168
[ 1900]
2 15
19 2
[1880]
210
216
[1860]
210
242
[2560]
290
10
[2590]
295
22
[2640]
300
46
[2660]
300
70
[2670]
3 00
95
[2660]
3 00
119
[2630]
295
143
[2600]
295
168
[2580]
290
192
[2550]
290
216
[2520]
285
241
[1250] [150 0]
85
10 5
[3170]
360
10
[3230]
365
21
[3290]
370
45
[3320]
375
69
[3350]
380
94
[3340]
375
119
[3340]
375
142
[3310]
375
167
[3280]
370
19 0
[3240]
365
214
[3210 ]
365
240
[2770]
3 15
8
[3030]
340
16
[3310 ]
375
36
[3410 ]
385
55
[3400]
385
74
[3400 ]
385
93
[3380]
380
112
[3370]
380
131
[3350]
380
151
[3340]
375
170
[3320]
375
189
[3460]
390
8
[3850]
435
16
[4120 ]
465
36
[4180]
470
54
[4260]
480
73
[4260]
480
92
[4270]
480
111
[4260]
480
130
[4240]
480
149
[4220]
475
168
[4210]
475
187
[4170]
470
7
[4620]
520
15
[4900 ]
555
35
[4980]
565
53
[5090]
575
72
[510 0 ]
575
91
[5110 ]
575
110
[510 0 ]
575
129
[5080]
575
147
[5060]
570
166
[5040]
570
18 5
[4890]
550
7
[5310]
600
15
[5640]
635
35
[5780]
655
52
[5870]
665
70
[5920]
670
89
[59 0 0 ]
665
10 8
[5880]
665
127
[5840]
660
145
[5810 ]
655
164
[5780]
655
18 3
[2250] [2500 ] [2750] [3000]
19 0
205
15 5
170
[1490] [2340]
170
265
210
209
[1350] [2250]
15 5
255
238
237
[1080] [ 1650]
120
18 5
285
284
[ 1520]
170
331
[3220]
365
208
[3080]
350
236
[2270]
255
282
[2120]
240
330
[2050]
230
376
[4160] [5010 ]
470
565
206
204
[4070] [4960]
460
560
235
233
[3020] [3850]
340
435
281
279
[2870] [3760]
325
425
328
325
[2790] [3620]
315
4 10
374
371
[5740]
650
2 01
[5700]
645
230
[5610] [6310] [7010] [7700]
870
715
790
635
2
5
4
7
[6000] [6750] [ 7490] [8240]
765
845
930
680
13
13
12
14
[6390] [7190 ] [7890] [8780]
990
8 10
890
720
32
34
33
34
[6580] [7400 ] [8220]
930
835
74 5
47
49
50
[6650] [7480]
845
750
66
68
[6730] [7560]
855
76 0
84
86
[6690]
755
10 5
[6650]
750
124
[4290]
485
9
[4450]
505
20
[4600]
520
44
[4680]
530
68
[4710 ]
530
93
[4740]
535
117
[4730]
535
141
[4710]
530
165
[470 0]
530
188
[4680]
530
2 11
[4670]
530
236
[4900]
555
9
[5070]
575
20
[5240]
590
44
[5330]
600
67
[5360]
605
92
[5390]
610
116
[5390]
6 10
140
[5380]
610
164
[5380]
6 10
18 7
[5370]
605
209
[5360]
605
234
[420] [ 1130] [1820] [2520] [3180] [3870] [4640] [5320]
130
205
285
360
440
525
45
600
266
266
265
264
262
260
267
258
[340] [1050] [1780] [2510] [3160] [3820] [4590] [5280]
40
520
120
20 0
285
355
430
595
303
296
303
302
3 01
300
299
293
[1010 ] [170 0] [2420] [310 0 ] [3720] [4500 ] [5140]
115
350
420
19 0
275
510
580
363
359
358
362
360
354
351
[1580] [2360] [2950] [3540] [4390]
180
335
4 00
265
495
422
419
418
420
413
[3250]
225
[350 0]
240
[4390]
495
413
[2110 ]
240
8
[2290]
260
17
[2470]
280
37
[2540]
285
56
[2550]
290
75
[2550]
290
94
[2520]
285
11 3
[2490]
280
132
[2460]
280
152
[2430]
275
17 1
[2400]
270
19 0
[3780]
425
10
[3830]
435
21
[3940]
445
45
[4000]
450
69
[4030]
455
94
[4070]
460
118
[4040]
455
142
[4000]
450
167
[3970]
450
189
[3930]
445
213
[3900 ]
440
238
[1750] [2000]
120
140
[8990] [9730]
1015 110 0
11
10
[10470]
118 5
8
}
Torque [lb-in]
Nm
Speed RPM
[2250] [2500]
155
170
[2750]
19 0
[3000]
205
[3250] [350 0]
225
240
[3750]
260
[5490]
620
9
[5680]
640
19
[5880]
665
43
[5980]
675
66
[6020]
680
91
[6050]
685
11 5
[6060]
685
139
[6060]
685
163
[6050]
685
18 5
[6040]
680
207
[6030]
680
232
[6670]
755
8
[6910 ]
780
18
[7150 ]
810
42
[7280]
825
64
[7320]
825
88
[7370]
835
10 9
[7270] [7880] [8490]
960
820
890
6
7
7
[7530] [8160] [8790]
850
920
995
17
17
16
[7790] [8450] [910 0 ]
880
955
1030
41
41
40
[7940]
895
63
[9080]
1025
5
[9420]
1065
15
[6080]
685
8
[63 00 ]
710
18
[6510 ]
735
42
[6630]
750
64
[6670]
755
89
[6710 ]
76 0
11 2
[6720]
76 0
135
[6730]
76 0
159
4000 Series
495 cm3/r [30.0 in3/r]
Performance Data
in production.
[.5]
1,9
[1]
Flow LPM [GPM]
3,8
[2]
7,5
[4]
15
[6]
23
[8]
30
[ 10 ]
38
[ 12 ]
45
[ 14 ]
Continuous
Peak
Intermittent
No Operation
53
[ 16 ]
61
[ 18 ]
68
[20]
76
625 cm3/r [38.0 in3/r]
[.5]
1,9
[1]
Flow LPM [GPM]
3,8
[2]
7,5
[4]
15
[6]
23
[8]
30
[ 10 ]
38
[ 12 ]
45
[ 14 ]
53
[ 16 ]
61
[ 18]
68
[20]
76
[25]
95
[30]
11 4
[35]
132
[40]
151
[25]
[250]
15
[500]
35
[750]
50
[1000]
70
[1250]
85
[1500]
105
[1600]
100
[1700]
115
[1800]
125
[1000]
115
2
[ 1080 ]
120
5
[1085]
125
14
[1090]
12 5
23
[ 1095]
12 5
35
[ 1100 ]
125
48
[ 1130]
13 0
60
[ 1160]
13 0
72
[1105]
12 5
84
[1050]
120
96
[990]
110
10 8
[930]
10 5
121
[2340]
265
5
[2380]
270
14
[2420]
275
23
[2460]
280
35
[2500]
280
48
[2550]
290
60
[2600]
295
72
[2535]
285
84
[2465]
280
95
[2405]
270
107
[2350]
265
120
[3600 ]
405
5
[3675]
415
14
[3750]
425
23
[3825]
430
35
[3900]
440
47
[3975]
450
59
[4050]
460
71
[3965]
450
83
[3880]
440
95
[3825]
430
107
[3770]
425
120
[4850]
550
4
[5010]
565
13
[5175]
585
22
[5220]
590
34
[5270]
595
46
[5320]
600
58
[5375]
605
70
[5325]
600
82
[5275]
595
94
[5240]
590
10 5
[5205]
590
118
[6100 ]
690
4
[6350]
715
12
[6600]
745
21
[6620]
750
33
[6640]
750
45
[6670]
755
57
[6700]
755
69
[6685]
755
81
[6670]
755
93
[6655]
750
104
[6640]
750
11 6
[7350]
830
3
[7625]
860
11
[7900]
895
19
[7950]
9 00
31
[7990]
905
43
[8045]
910
54
[8100 ]
915
65
[8065]
910
77
[8035]
910
89
[7345]
830
100
[7820]
885
3
[8115]
915
10
[8410]
950
18
[8430]
950
30
[8460]
955
43
[8595]
970
53
[8660]
980
64
[8620]
975
76
[8580]
970
88
[8290]
935
2
[8605]
970
9
[9000]
1015
17
[8910 ]
100 5
29
[8925]
1010
42
[9150]
1035
52
[8760]
990
2
[9095]
1030
8
[9590]
1085
16
[9490]
1070
28
[750] [2175] [3600]
85
245
405
151
150
149
[550] [1975] [3400]
60
225
385
18 1
18 0
17 9
[3125]
355
210
[2850]
320
241
[2000]
140
95
[30]
[250]
15
[50 0]
35
[800 ]
90
3
[880]
10 0
7
[905]
10 0
18
[935]
10 5
30
[920]
10 5
45
[905]
100
61
[880]
100
76
[860]
95
91
[830]
95
10 6
[805]
90
122
[ 740]
85
137
[680]
75
153
[ 1750]
20 0
1
[ 1875]
2 10
6
[ 1940]
220
17
[2005]
225
29
[2010]
225
44
[2015]
230
60
[1995]
225
75
[1975]
225
90
[1945]
220
10 5
[1910 ]
215
120
[1860]
210
136
[1810]
205
152
[570]
65
191
[1665] [2800] [4005] [5210] [6135]
190
315
455
590
695
189
187
184
182
177
[1520] [2645] [3765] [4885] [5985]
170
300
425
550
675
228
226
223
220
215
[2400] [3510]
270
395
265
263
[2155] [3260]
245
370
305
303
[2850]
320
241
}
11 4
[35]
132
[40]
151
[10075]
1140
7
[10450]
118 0
14
[750] [ 1000 ]
50
70
[1250] [15 0 0] [ 1750] [2000]
85
10 5
12 0
140
[2875] [3825] [4775]
325
430
540
6
5
4
[2975] [3990] [5010 ]
335
450
565
17
16
15
[3075] [4160] [5245]
345
470
595
28
27
26
[3100] [4185] [5265]
350
475
595
43
42
40
[3125] [4205] [5290]
355
475
600
59
57
55
[3095] [4205] [5295]
350
475
600
74
72
70
[3095] [4200] [5305]
350
475
600
89
87
85
[3055] [4165] [5275]
345
470
595
10 4
10 2
100
[3020] [4130] [5245]
340
465
595
119
117
115
[2980] [4105] [5235]
335
465
590
134
132
130
[2940] [4085] [5225]
330
460
590
150
147
145
[5720]
645
3
[6010 ]
680
12
[6300]
710
23
[6345]
715
37
[6385]
720
52
[6390]
720
66
[6390]
720
81
[6360]
720
96
[6330]
715
111
[6305]
715
125
[6285]
710
140
[6670]
755
2
[701 0 ]
790
11
[7355]
830
21
[7420]
840
35
[7485]
845
49
[7480]
845
63
[ 7475]
845
77
[ 7445]
840
92
[ 7420]
840
107
[7380]
835
121
[2250]
15 5
[760 0]
860
1
[8000] [8980]
1015
905
8
10
[8375] [9400]
1060
945
17
19
[8445] [9465]
1070
955
30
32
[8510]
960
46
[8525]
960
59
[2500 ]
170
[10350]
1170
14
Torque [lb-in]
Nm
Speed RPM
C-4
[5000] [6400]
565
725
147
146
[4800] [6200]
530
700
177
176
[4545]
515
208
[4295]
485
239
C-4-7
4000 Series
Ports
1 1/16 -12 UN-2B SAE O-ring Staggered Ports (2)
4 Bolt 3/4 inch Split Flange Ports (2)
Dimensions
Standard Mount
Standard Mount
Port B
YY Max.
Port B
XX
Y Max.
X
22,4/21,8
[.88/.86]
127,0 [5.00]
Dia. Bolt Circle
101,60/101,47
[4.000/3.995]
Dia.
10,7/9,1
[.42/.36]
4 Bolt 3/4 Inch
Case Drain Port
Split Flange Ports
SAE C Flange
119,9
[4.72]
Max,
Square
Add 4,3 [.17] to
X and Y Dim.
(see Chart)
Flange
Comparison
SAE B/ SAE C
89,80
[3.536]
Square
12,7/12,4
[.50/.49]
15,2/14,5
[.60/.57] (4)
14,53/14,15
[.572/.557] Dia.
Thru Max.
127,00/126,87
[5.000/4.995]
Pilot Dia.
148,3
[5.84]
Max.
Square
161,92
[6.375]
Dia. B.C.
26,7/26.2
[1.05/1.03]
76,2/63,5
[3.00/2.50]
4,3/3,3
[.17/.13]
Displacement
XYXX
YY
mm [inch]
mm [inch]
mm [inch]
110 [ 6.7] 130 [ 7.9] 160 [ 9.9] 205 [12.5] 245 [15.0] 310 [19.0] 395 [24.0] 495 [30.0] 625 [38.0] C-4-8
158,3 [6.23] 162,3 [6.39] 168,7 [6.64] 177,2 [6.98] 168,7 [6.64] 177,2 [6.98] 187,9 [7.40] 200,7 [7.90] 217,8 [8.58] 214,4 [ 8.44] 218,4 [ 8.60] 224,7 [ 8.85] 233,2 [ 9.18] 224,7 [ 8.85] 233,2 [ 9.18] 243,9 [ 9.60] 256,8 [10.11] 273,9 [10.78] 167,3 [6.59] 246,3 [ 9.70]
171,3 [6.75] 250,4 [ 9.86]
177,7 [7.00] 256,7 [10.11]
186,2 [7.33] 265,2 [10.44]
177,7 [7.00] 256,7 [10.11]
186,2 [7.33] 265,2 [10.44]
196,9 [7.75] 275,9 [10.86]
209,7 [8.26] 288,8 [11.37]
226,7 [8.93] 305,9 [12.04]
4000 Series
Ports
G 1/4 (BSP) Case Drain Port (1) Dimensions
Wheel Mount
Wheel Mount
Port B
YY Max.
Port B
XX
Y Max.
4 Bolt 3/4 inch
Split Flange Ports
21,8/21,3
[.86/.84]
Case Drain Port
Case Drain Port
148,8 [5.86] Max. Square
124,2 [4.89] Max.
81,8 [3.22]
139,70/139,57
[5.500/5.495]
Dia.
108,7 [4.28]
Dia. Max.
9,7/8,6
[.38/.34]
X
C-4
116,74
[4.596]
Squa re
14,53/14,15
[.572/.557]
Thru (4)
165,0 [6.50]
Dia. Bolt Circle
Displacement
XYXX
YY
mm [inch]
mm [inch]
mm [inch]
110 [ 6.7] 130 [ 7.9] 160 [ 9.9] 205 [12.5] 245 [15.0] 310 [19.0] 395 [24.0] 495 [30.0] 625 [38.0] 87,5 [3.45] 91,6 [3.61] 97,8 [3.85]
106,4 [4.19] 97,8 [3.85] 106,4 [4.19] 117,1 [4.61] 129,9 [5.12] 146,9 [5.79] 143,3 [5.64] 147,3 [5.80] 153,7 [6.05] 162,3 [6.39] 153,7 [6.05] 162,3 [6.39] 173,0 [6.81] 185,7 [7.31] 202,9 [7.99] 96,4 [3.80]
100,5 [3.96] 106,8 [4.21] 115,4 [4.55] 106,8 [4.21] 115,4 [4.55]
126,1 [4.97] 138,8 [5.47] 156,0 [6.14] EATON Low Speed High Torque Motors E-MOLO-MC001-E6 September 2011
175,3 [6.90]
179,3 [7.06]
185,7 [7.31]
194,3 [7.65]
185,7 [7.31]
194,3 [7.65]
205,0 [8.07]
217,7 [8.57]
235,0 [9.25]
C-4-9
4000 Series
Ports
G 1/4 (BSP) Case Drain Port (1) Dimensions
Bearlingless
Bearingless
YY Max.
XX
Y Max.
Port B
Port B
161,9 [6.375]
Bolt Circle
X
127,0/126,9
[5.000/4.995]
Dia.
4 Bolt 3/4 inch
Split Flange Ports
14.50/14,14
[.572/.557]
114,5
[4.508]
Squa re
Case Flow Hole
147,6 [5.81] Max. Square
Case Drain Port
12,4 [.49]
25,9 [1.02]
For 4000 Series Bearingless
Motor application information contact your Eaton
representative (mating
coupling blanks available
from Eaton Hydraulics).
Note:
C
D
E
F
G
H
J
K
C
24,1/21,1
[.95/.83]
D
47,2 [1.86] Dia.
112,5 [4.43] Max.
107,4 [4.23] Full Form Dia.
7,4 [.29]Min. Full Form Dia.
68,8 [2.71] Max.
56,9 [2.24] Dia.
18,29 [.720]
38º
E
K
J
C-4-10
Face Seal or O-ring Seal
F
G
H
Displacement
XYXX
YY
mm [inch]
mm [inch]
mm [inch]
110 [ 6.7] 130 [ 7.9] 160 [ 9.9] 205 [12.5] 245 [15.0] 310 [19.0] 395 [24.0] 495 [30.0] 625 [38.0] EATON Low Speed High Torque Motors E-MOLO-MC001-E6 September 2011
91,0 [3.58] 95,0 [3.74] 101,4 [4.00] 109,9 [4.33] 101,4 [4.00] 109,9 [4.33] 120,6 [4.75] 133,5 [5.26] 150,5 [5.93]
146,8 [5.78] 150,8 [5.94] 157,1 [6.19] 165,7 [6.52] 157,1 [6.19] 165,7 [6.52] 176,3 [6.94] 189,2 [7.45] 206,3 [8.12] 100,1 [3.94] 104,1 [4.10]
110,5 [4.35] 118,9 [4.68] 110,5 [4.35] 118,9 [4.68] 129,5 [5.10] 142,5 [5.61] 159,5 [6.28] 178,8 [7.04]
182,9 [7.20]
189,2 [7.45]
197,6 [7.78]
189,2 [7.45]
197,6 [7.78]
208,3 [8.20]
221,2 [8.71]
238,3 [9.38]
4000 Series
1 Internal spline in mating part to be as
follows: Material to be ASTM A304,
8620H. Carbonize to a hardness of 60-64
HRc with case depth (to 50HRc) of 0,076
- 1,27 [.030 - .050] (dimensions apply after
heat treat).
Bearingless
14,0/13,2
[.55/.52]
16
5,1/4,6 [.20/.18]
Dia. (2) Thru Oil Hole
1,5/0,8
[.06/.03]
30º
15º
0,13 [.005]
7 52,8 [2.08] Max. dimension to be
maintained when assembling shipping
and installing unit to insure valve drive
engagement with valve (this is required
on displacement code number 24 only).
8,9/8,4
[.35/.33]
31º
29º
2
53,6/52,6
[2.11/2.07]
Coupling Depth
B
5
5,6/5,1
[.22/.20]
Case Flow
23,1/22,6
[.91/.89]
65,0/64,5
[2.56/2.54]
7
Case Flow
52,37
[2.062]
R
Dia. Min.
1,8/1,2
[.07/.05]
49,848/49,822
[1.9625/1.9615] Dia.
-D-
be provided.
[1.9689 - 1.9700] ID by 60,050 - 60,080
[2.3642 - 2.3653] (Oilite bronze sleeve
bearing).
6 Similar to SAE “C” Four Bolt Flange.
( -B- )
3
6
4
Circular
Major
Finish
Finish
Tip R .
Minor
Fillet R.
Pitch
Form
Spline Pitch.................................................................................................. 10/20
Pressure Angle................................................................................................30°
Number of teeth............................................................................................... 12
Class of Fit................................................................................................... Ref. 5
Type of Fit...................................................................................................... Side
| 0,20 [.008] | D
Major Diameter.....................................33,43 [1.316] Max. 33,23 [1.308] Min.
Min. Minor Diameter............................................ 28,40 - 28,58 [1.118 - 1.125]
Fillet Radius.................................................................... 0,63 - 0,76 [.025 - .030]
Tip Radius....................................................................... 0,26 - 0,51 [.010 - .020]
Finish..........................................................................................................1,6 (63)
Lead Variation.................................................................................0,013 [.0005]
Maximum Actual......................................................................5,045 [.1986]
Dimension Between Two Pins............... Ref. 22,783 - 22,929 [.8970 - .9027]
Pin Diameter.........................................5,334 [.2100] Pins to Have 3,73 [.147]
.
C-4-11
C-4
4000 Series
1 1/4 Inch Straight
Dimensions
70,9/68,6 [2.79/2.70]
End of Shaft to
Mounting Surface (Std)
768 [6800]
Max. Torque
Nm [lb-in]
Shafts
42,0/40,6
[1.65/1.60]
35,33/35,07
[1.391/1.381]
7,963/7,937
[.3135/.3125]
Square Key
31,75/31,69
[1.250/1.248]
Dia.
3/8-16 UNC
18,7[.74] Deep
1 1/4 -14 Tooth Splined
70,9/68,6 [2.79/2.70]
End of Shaft to
38,1 [1.50]
Min. Full
Spline
768 [6800]
Max. Torqu e
Nm [lb-in]
1 5/8 Tapered
53,1 [2.09]
Max.
Coupling
164,8/162,1 [6.49/6.38]
End of Shaft to
Mounting Surface (Whl)
1-1/4-18 UNEF-2A
31,7 [1.25]
972 [8600] Max.
Torque Nm
[lb-in]
41,326/41,275
[1.6270/1.6250] Dia.
3/8-16 UNC
18,7 [.74] Deep
Spline to Fit ANSI B92.1 1976
12/24 Spline
31,7
[1.250]
Dia.
53,1 [2.09]
Max. Coupling
4,1 [.16]
Dia. Thru
76,6 [3.00]
11,138/11,112
[.4385/.4375]
Sq. Key
SAE J501 Standard Tapered Shaft
125,00 0,17 Taper per Mete r
[1.500 .002 Taper per Foot]
5,54/5,20
[.218/.205]
40 mm Straight
972 [8600] Max. 12,000/11.957
Torque Nm
[.4724/.4708]
[lb-in]
8,000/7,900
[.3149/.3115]
93,9/92,0 [3.696/3.622]
End of Shaft to
40,02/39,99
[1.576/1.575]
Dia.
1 1/2 Inch 17-Tooth Splined
972 [8600] Max.
Torque Nm
[lb-in]
31,2 [1.23]
Min. Full
Spline
59,1/56,8
[2.325/2.235]
9,2/4,5 [.36/.18]
70,7/69,3
[2.78/2.73]
43,03/42,72
[1.694/1.682]
M12 x 1,75 -6H
24,9 [.98] Deep
81,3 [3.20]
Max. Coupling
66,8/65,0 [2.63/2.56]
End of Shaft to
Hub
(645 Nm [475 lb-ft] Dry)
(510 Nm [375 lb-ft] Lub)
Plus Torque required t o
align the slotted nut with
Slotted Hexagon Nut
33,28/33,02
[1.310/1.300]
Dia.
55,4 [2.18]
11,2 [.44]
4,6 [.18]
38,10 [1.500] Dia.
3/8-16 UNC
Spline to
18,7 [.74] Deep
Fit ANSI B92.1 1976
51,8 [2.04]
12/24 Spline
Max. Coupling
C-4-12
1-1/4-18 UNEF
30°
30°
15,7 [.62]
4000 Series
kg [1000 lb]. Note:
the allowable Inward thrust
94 kg/7 Bar [208 lb/100 PSI].
Standard Motor
[lb]
[8000]
kg
3500
[7000]
3000
[6000]
2500
[5000]
2000
[4000]
[3000]
1500
[2000]
1000
[1000]
500
mm -100 -80 -60 -40 -20 0 20 40 60 80 100 120
[inch] [-4] [-3] [-2] [-1] 0
Thrust Load
[1] [2] [3] [4] [5]
Mounting Surface
Max. Axial Loads
454 kg [1000 lb]
Wheel Motor Tapered Shaft
[lb]
kg
below.
[9000]
4000
RPM
1.23
1.00
0.81
0.72
0.66
0.62
0.58
0.56
0.54
[2000]
1000
50
100
200
300
400
500
600
700
800
[1000]
500
[8000]
[7000]
[6000]
[5000]
[4000]
[3000]
0
3500
3000
2500
C-4
2000
1500
0
mm -20 0 20 40 60 80 100 120 140 160 180
[inch] [-1]
0
[1]
[2]
[3]
[4]
[5]
[6]
[7]
Mounting Surface
C-4-13
4000 Series
Allowable case pressure
is highest at low shaft
speeds. Consequently,
motor life will be shortened
if case pressure exceeds
these ratings (acceptability
may vary with application).
limitation chart.
C-4-14
[2000]
[1500]
100
Case
Pressure
Bar
50
[PSI]
0
Optional
[1000]
[ 500]
0
0
Case Drain
Required
Optional
0
100 200 300 400 500 600 700 800 900
Speed RPM
4000 Series
Dimensions
Ports
7/16-20 UNF O-ring or
1-1/16-12 GO-ring
Ports
1/4 (BSP) Case
Drain(2)
Port or
2,16/1,40
G 3/4 (BSP) Ports (2)
[.085/.055]
4 Bolt 3/4 Inch Split Flange Ports
to Fit SAE J518 c (2)
Port B
G 1/4 (BSP) Case Drain Port
2,16/1,40
[.085/.055]
29,5/29,0
[1.16/1.14]
Port
B
7/16-20
13,2UNF
[.52]O-ring or
G 1/4 (BSP) Case Drain Port
29,5/29,0
Port B
[1.16/1.14]
13,2 [.52]
Port A
58,9
69,6 [2.32]
[2.74]Max.15,7 [.62]
Max.
17º
69,6 58,9
58,9
[2.74][2.32] Max.
[2.32]
Max.
Max.
17º
Port A
52,3/51,8
[2.06/2.04]
Port A
52,3/51,8
[2.06/2.04]
42,7/38,1
[1.68/1.50]
52,3/51,842,7/38,1
[2.06/2.04][1.68/1.50]
76,5 [3.01]
Max. 42,7/38,1
[1.68/1.50]
M12 x 1,5-6H O-ring
Case Drain Port
76,5 [3.01]
Max.
58,9
58,9
[2.32]
[2.32] Max.
Max.
Port B
76,5 [3.01]
7/8-14
58,9 O-ring Ports (2) orM12 x 1,5-6H O-ring
Max.
Max.
M22[2.32]
x 1,5-6H
Ports (2) Case Drain Port
29,5/29,0
Port B[1.16/1.14]
13,2 [.52]
29,5/29,0
Port B
17º
[1.16/1.14]
13,2 [.52]
69,6
[2.74]
29,5/29,0
Max.
[1.16/1.14]
17º
13,2 [.52]
69,6
58,9
[2.74]
[2.32]
Max.
Max.
58,9
[2.32]
Max.
Port B
2,16/1,40
[.085/.055]
Port A
15,7 [.62]
29,5/29,0
[1.16/1.14]
13,2
69,6[.52]
[2.74]
17º
Max.
15,7 [.62]
58,9
69,6 [2.32]
[2.74]Max.
Max.
7/16-20 UNF O-ring
Case Drain Port
10,59/9,83
[.417/.387]
7/16-20 UNF O-ring
Case Drain Port11,2 [.44]
10,59/9,83
45º
[.417/.387]
54,9
[2.16]
19,02/18,77
Port A
22,23 [.875]
[.749/.739]
47,63 [1.875]Port B
11,2 [.44] 52,3/51,8
[2.06/2.04]
23,9 [.94]
45º 17º
54,9 [2.16]
Port A
19,02/18,77
22,23 [.875]
47,63 [1.875]
73,4 [.749/.739]
11,2 [.44]
42,7/38,1
52,3/51,8
[2.89]
23,9 [.94]
45º
54,9
[2.16] [1.68/1.50]
[2.06/2.04]
Max.
17º
19,02/18,77
22,23 [.875]
[.749/.739]
58,7
52,3/51,8
73,4 [2.31]
42,7/38,1
[2.06/2.04]
[2.89]Max.
17º
[1.68/1.50]
Max.
58,7
76,5 [3.01]
[2.31]
73,4
58,7
Max. 42,7/38,1
Max.
[2.89]
[2.31]
[1.68/1.50]
Max.
Max.
47,63 [1.875]
Port B
23,9 [.94]
6,73/5,99
9/16-18 UNF
O-ring or
[.265/.235]
M12Port
x 1,5-6H
O-ring
A
Case Drain Port
15,7 [.62]
6,9 [.27] Material Removed
from this Housing for
6,73/5,99
7/8-14 O-ring Ports and
[.265/.235] M22 x 1,5-6H Ports
Port A
58,7
[2.31]
Max.
58,7
[2.31]
Max.
76,5 [3.01]
Max.
58,7
[2.31]
Max.
76,5 [3.01]
Max.
C-4
15,7 [.62]
42,7/38,1
6,73/5,99
[1.68/1.50]
[.265/.235]
7/8-14 O-ring Ports and
Port A
M22 x 1,5-6H Ports
15,7 [.62]
17º
58,9
[2.32]
Max.
7/16-20 UNF O-ring
Case Drain Port
10,59/9,83
[.417/.387]
42,7/38,17/8-14 O-ring Ports and
[1.68/1.50]
M22 x 1,5-6H Ports
76,5 [3.01]
Max. 42,7/38,1
[1.68/1.50]
58,9
[2.32]
Max.
76,5 [3.01]
Max.
58,9
[2.32]
Max.
76,5 [3.01]
Max.
C-4-15
4000 Series
Note:
in the charts below: Use
product in detail.
Product Numbers
Mounting
Shaft
Use digit prefix —109-,
110-, or 111- plus four digit
number from charts for
Example 111-1057.
Orders will not be
accepted without three
digit prefix.
Port SizeDispl. cm3/ r [in3/ r] / Product Number
110
[ 6.7] 130
[ 7.9] 160
[ 9.9] 205
[12.5] 245
[15.0] 280*
[17.1]
310
[19.0] 395
[24.0] 495
[30.0] 625
[38.0]
1 1/4 Inch Straight
109-1100
-1101
-1102
-1103
-1104
-1094
-1105
-1106
-1212
-1215
inch Split Flange 109-1001
-1054
-1002
-1003
-1055
—
-1056
-1057
—
—
109-1107
-1108
-1109
-1110
-1111
—
-1112
-1113
-1479
-1455
-1058
-1007
-1008
-1059
—
-1402
-1061
—
—
109-1114
-1115
-1116
-1117
-1118
—
-1119
-1120
—
—
-1062
-1012
-1013
-1063
—
-1064
-1065
—
—
109-1184
-1185
-1227
-1224
-1225
—
-1189
-1190
—
—
109-1191
-1192
-1193
-1194
-1195
—
-1196
-1197
—
—
110-1074
-1075
-1076
-1077
-1078
—
-1079
-1080
—
-1122
-1040
-1002
-1003
-1041
—
-1042
-1043
—
—
Standard
1 5/8 Inch
SAE
Tapered
B-Mount
1 1/4 Inch
14
T Splined
1 1/16 O-ring
3/4
1 1/16 O-ring
3/4
1 1/16 O-ring
3/4
Standard
40 mm Straight
G 3/4 (BSP)
SAE
1 1/4 Inch 17 T SplinedG 3/4 (BSP)
C-Mount
1 1/16 O-ring
1 1/4 Inch Straight
3/4
G 3/4 (BSP)
110-1108
-1109
-1110
-1111
-1112
—
-1113
-1125
—
—
1 1/16 O-ring
110-1081
-1082
-1083
-1084
-1085
—
-1086
-1087
1116
-1117
-1044
-1007
-1008
-1045
—
-1046
-1047
—
—
110-1088
-1089
-1090
-1091
-1092
—
-1093
-1094
—
—
-1048
-1012
-1013
-1049
—
-1050
-1051
—
—
111-1033
-1034
-1035
-1036
-1037
—
-1038
-1039
-1062
-1063
-1015
-1045
-1046
-1016
—
-1017
-1018
—
—
-1053
-1054
-1055
-1056
—
-1057
-1058
—
—
40 mm Straight
Wheel
1 5/8 Inch
Motor
Tapered
3/4
1 1/16 O-ring
1 1/4 Inch
14 T Splined
3/4
1 1/16 O-ring
Bearingless
3/4
G 3/4 (BSP)
111-1052
* New Release
C-4-16
111-1057
4000 Series
The following 30-digit coding system has been developed to
identify all of the configuration options for the 4000 Series
motor. Use this model code to specify a motor with the
desired features. All 30 digits of the code must be present
when ordering. You may want to photocopy the matrix below
to ensure that each number is entered in the correct box.
Model Code
M
0 4
* **
1
2 3
4 5 6
**
7
8
1 Product
M - Motor
2 , 3 Series
04 – 4000 Series
cm3/r [in3/r]
067 - 109.8 cm3/r [6.70 in3/r]
080 - 130.3 cm3/r [7.95 in3/r]
099 - 162.2 cm3/r [9.90 in3/r]
125 - 205.5 cm3/r [12.54 in3/r]
150 - 246.3 cm3/r [15.03 in3/r]
171 - 280.1 cm3/r [17.09 in3/r]
190 - 311.8 cm3/r [19.03 in3/r]
225 - 369.0 cm3/r [22.52 in3/r]
240 - 393.9 cm3/r [24.04 in3/r]
301 - 492.6 cm3/r [30.06 in3/r]
342 - 560.2 cm3/r [34.18 in3/r]
381 - 623.9 cm3/r [38.07 in3/r]
7 , 8 Mounting Type
AA – Bearingless, 4 Bolt:
127.00 [5.000] Pilot Dia.
14.27 [.562] Dia. Holes on
161.92 [6.375] Dia. Bolt
Circle
AB – Standard, 4 Bolt:
101.60 [4.000] Pilot Dia. 14.7
[.58] Slots on 127.00 [5.000]
Dia. Bolt Circle. (SAE B)
AC – Wheel, 4 Bolt: 139.70
[5.500] Pilot Dia. 14.27
[.562] Dia. Holes on 165.10
[6.500] Dia. Bolt Circle.
AD – Wheel, 4 Bolt: 127.00
[5.000] Pilot Dia. .500-13
UNC-2B Threaded Holes
on 147.62 [5.812] Dia. Bolt
circle.
AF – Standard, 4 Bolt:
127.00 [5.000] Pilot Dia.
14.27 [.562] Dia. Holes on
161.92 [6.375] Dia. Bolt
Circle. (SAE C)
AH – Standard: ISO Flange
125 B4hw (ISO 3019/2)
124.97 [4.920] Pilot Dia.
14.27 [.562] Dia. Holes on
160.00 [6.299] Dia. Bolt
Circle
* *
**
9 10
11 12
**
*
**
*
*
13 14 15 16 17 18 19
AP – Wheel, 4 Bolt: 160.0
[6.30] Pilot Dia. with 5.8 [.23]
Pilot Length and 18.00 [.709]
Dia Holes on 200.00 [7.874]
Bolt Circle (ISO Compatible)
9 , 10 Output Shaft
01 – 31.75 [1.250] Dia.
Straight With .375-16UNC2B Thread, 53.1 [2.09] Max
Coupling Length, 7.938
[.3125] Sq x 41.27 [1.625]
Straight Key
02 – 41.28 [1.625] Dia.
Tapered with 11.112 [.4375]
Sq x 31.75 [1.250] Straight
Key, 1.250-18UNEF-2A
Thread with Slotted Hex
Nut
03 – 31.75 [1.250] Dia. Flat
Spline, 38.1 [1.50] Minimum
Full Spline Length with
.375-16UNC-2B Thread
10 – 38.10 [1.500] Dia. Flat
12/24 DP 30°. Involute
Spline, 31.2 [1.23] Minimum
Full Spline Length, with
.375-16 UNC-2B Thread in
End
11 – 40.00 [1.575] Dia.
Straight with M12 x
1.75-6H Thread, 7.955
[.3132] x 11.979 [.4716]
Wide X 69.98 [2.755]
Straight Key
21 – 40.00 [1.575] Dia.
10:1 Tapered Shaft per ISO
R775 with .750-16 UNF-2B
Threaded in End, 12W x 8H
70L [.472W x .313H x 2.76L]
Key
European Spline
25 – 42.00 [1.654] Dia. 10:1
Tapered Shaft per ISO R775
with .750-16 UNF-2B Thread
in End, 12W x 8H X 63L
[.472W X .313H X 2.48L]
Key
**
**
**
**
**
*
20 21
22 23
24 25
26 27
28 29
30
11 , 12 Ports
AA – .875-14 UNF-2B SAE
O-Ring Ports - Staggered
Ports
AB – 1.0625-12 UN-2B SAE
O-Ring Ports - Staggered
Ports
AC – G 3/4 Ports Staggered Ports
AD – 19.05 [.750] 4 Bolt
Split Flange Staggered Ports
Standard Pressure Series
(Code 61)
AE – M22 X 1.5-6H O-Ring
Port - Staggered Ports
AG – 12.70 [.500] Dia.
Manifold Ports
AJ – Dash 12 Stc Type II+
(Snap to Connect) Ports Staggered Ports
00 – None
01 – .5625-18 UNF-2B SAE
O-Ring Port with Shuttle
02 – .4375-20 UNF-2B SAE
O-ring Port with Check
Valve
03 – G 1/4 BSP Straight
Thread with Check Valve
06 – .4375-20 UNF-2B SAE
O-ring Port with Reverse
Flow Shuttle
10 – Dash 6 Stc Type II +
(Snap to Connect) Port
0 – None
A – Set at 4.5 Bar
[65 lbf/In2]
B – Set at 15.2 Bar
[220 lbf/In2]
16 , 17 Pressure/Flow
Option
00 – None
18 Geroler Option
0 – Standard
19 Seal Option
0 – Standard
1 – Viton
4 – Seal Guard
20 , 21 Accessories
00 – None
AC – M 12 Threaded
Connector, Long Body
Digital Speed and Direction
Pickup (Two 36 Pulse Signals
in Quadrature per Revolution
Pin 1=Power Supply, Pin
2=Output Signal 1, Pin
3=Common, Pin 4=Output
Signal 2)
AD – M 12 Threaded
Connector, Digital Speed
And Direction Pickup (One
72 Pulse per Rev Speed
Signal and One Directional
Signal (Pin 1=Power,
Pin 2=Direction, Pin
2=Common, Pin 4=Speed)
Features
22 , 23 Special
(Hardware)
00 – None
17 – Low Noise Valve Plate
(Assembly)
00 – None
Box
AA – Low Gloss Black
AB – Epoxy Coated (Frost
Gray), Individual Box
28 , 29 Customer
Identification
00 – None
30 Design Code
F – Sixth
C-4-17
C-4
Notes
C-4-18
6000 Series
Features
Highlights
• Presents a multitude of
options that make this
motor very “smart” and
flexible to apply
• 9 displacements available
Benefits
• Very tough motor for
demanding applications
• Can be used in a multitude of industries
• Very easy/flexible to integrate in a system
Applications
• Mobile equipment
• Snow Removal, mowing
• Spayer, trencher
• Wood products
Description
With torque up to 15,000 in-lb and 40 gpm
continuous, this motor is packed with power operates
very smoothly.
Specifications
Geroler Element
Flow l/min [GPM]
Speed RPM
Pressure bar [PSI]
Torque Nm [lb-in]
9 Displacements
775 Cont.**
866 Inter.*
200 [3000] Cont.**
300 [4500] Inter.*
1685 [14920] Cont.**
1875 [16580] Inter.*
** Continuous — (Cont.) Continuous rating, motor may be run continuously at these ratings.
* Intermittent — (Inter.) Intermittent operation, 10% of every minute.
C-5
Mowing
Snow Removal
Sprayer
Trencher
EATON Low Speed High Torque Motors E-MOLO-MC001-E6 JSeptember 2011
C-5-1
6000 Series
Specifications
6000 Series Motors
Displ. cm 3/r [in 3/r]
195 [11.9]
245 [15.0]
310 [19.0]
390 [23.9]
490 [30.0]
625 [38.0]
735 [45.0]
805 [49.0]
985 [60.0]
Max. Speed
Continuous
775
615485387307241203187153
(RPM)
Intermittent
866
834698570454355303280230
@ Flow
Flow
Continuous 150 [40] 150 [40]
150 [40]
150 [40]
150 [40]
150 [40]
150 [40]
150 [40]
150 [40]
l/min [GPM] Intermittent 170 [45] 210 [55]
225 [60]
225 [60]
225[60]
225 [60]
225[60]
225[60]
225 [60]
Torque*
Continuous 575 [5100] 735 [6510] 930 [ 8230] 1155 [10230] 1445 [12800] 1480 [13100] 1378 [12192] 1582 [14004] 1685 [14920]
Nm [lb-in] Intermittent 860 [7620] 1100 [9740] 1355 [11990] 1635 [14490] 1885 [16670] 1898 [16800] 1699 [15040] 1850 [16377] 1875 [16580]
Pressure Continuous 205 [3000] 205 [3000] 205 [3000] 205 [3000] 205 [3000] 170 [2500] 140 [2000] 140 [2000] 140 [2000]
∆ bar
Intermittent 310 [4500] 310 [4500] 310 [4500] 310 [4500] 275 [4000] 221 [3200] 170 [2500] 170 [2500 140 [2000]
[∆ PSI]
Peak
310 [4500] 310 [4500] 310 [4500] 310 [4500] 310 [4500] 240 [3500] 205 [3000] 170 [2500 170 [2250]
Weight
Standard or 24,9 [55.0] 25,2 [55.5] 25,6 [56.5] 26,3 [58.0] 27.0 [59.5]
27,9 [61.5]
28.6 [63.0]
29 [64.0]
30,4 [67.0]
kg [lb]
Wheel Mount
Bearingless 20.2 [44.5] 20.4 [45.0] 20.9 [46.0] 21.5 [47.5] 22.2 [49.0] 23.1 [51.0] 28.3 [52.5] 28.8 [53.5] 30.2 [56.5]
Note:
load applications.
310 bar [4500 PSI]
∆ bar [∆ PSI] :
outlet port
Continuous Rating:
10% of every minute
Peak Operation:
1% of every minute
C-5-2
Recommended Fluids:
Recommended System
Operating Temp.:
-34°C to 82°C [-30°F to
180°F]
4406: 20/18/13
6000 Series
195 cm3/r [11.9 in3/r]
Performance Data
[.5]
in production.
1,9
[2]
Flow LPM [GPM]
7,5
[4]
15
[8]
30
[ 12 ]
45
[ 16 ]
61
[20]
76
[24]
91
[28]
Continuous
Peak
Intermittent
No Operation
10 6
[32]
121
[36]
136
[40]
151
[250]
15
[500]
35
[1000]
70
[1500]
105
[2000]
140
[280]
30
9
[290]
35
38
[300]
35
77
[310]
35
154
[320]
35
232
[300]
35
309
[270]
30
387
[240]
25
465
[190]
20
542
[160]
20
620
[120]
15
697
[80]
10
775
[650]
75
7
[680]
75
37
[710]
80
76
[740]
85
153
[750]
85
230
[730]
80
307
[720]
80
384
[700 ]
80
462
[660]
75
539
[630]
70
617
[620]
70
692
[610 ]
70
770
[590]
65
866
[1450]
16 5
5
[1500]
17 0
35
[1500]
17 5
74
[1590]
180
148
[1610]
180
225
[1600]
180
303
[1590]
180
379
[1570]
175
456
[1530]
175
532
[1500]
170
609
[1480]
165
683
[1450]
16 5
759
[1410]
160
854
[2290]
260
2
[2340]
265
34
[2390]
270
72
[2450]
275
144
[2480]
280
221
[2470]
280
300
[2460]
280
3 74
[2440]
275
450
[2400]
270
526
[2370]
270
602
[2350]
265
674
[2320]
260
74 9
[2280]
260
843
[3100]
350
30
[3200]
365
66
[3280]
370
131
[3330]
375
212
[3340]
375
291
[3350]
380
365
[3330]
375
440
[3300 ]
375
514
[3270]
370
589
[3240]
365
659
[3210]
365
733
[3170]
360
825
[45]
245 cm3/r [15.0 in3/r]
[250]
15
[.5]
1,9
[2]
Flow LPM [GPM]
7,5
[4]
15
[8]
30
[ 12 ]
45
[ 16 ]
61
[20]
76
[24]
91
[28]
10 6
[32]
121
[36]
136
[40]
151
[45]
17 0
[50]
18 9
[55]
208
[500]
35
[1000]
70
[1000]
105
[2000]
140
[430] [860] [ 1890]
50
95
215
7
4
1
[440] [9 0 0 ] [ 1940] [2990]
50
10 0
220
340
30
29
26
24
[460] [940] [2 00 0 ] [3060]
50
10 5
225
345
61
60
56
54
[470]
[960] [2060] [3150]
55
110
235
355
122
120
11 6
11 3
[480] [970] [2080] [3180]
55
110
235
360
18 3
18 2
17 8
174
[450] [960] [2070] [3180]
50
110
235
360
245
244
240
236
[420] [940] [2050] [3160]
45
10 5
230
355
307
306
3 01
297
[380] [920] [2020] [3120]
45
10 5
230
355
368
365
361
358
[330] [870] [1980] [3100]
35
100
225
350
430
426
421
416
[290] [800] [1920] [3050]
35
90
215
345
491
489
481
475
[250] [730] [1850] [2980]
30
80
210
335
556
549
543
537
[200 ] [690] [1790] [2940]
25
80
2 00
330
615
612
606
599
[570] [1760] [2860]
65
2 00
325
682
688
674
[1720] [2800]
19 5
315
758
749
[1670] [2740]
19 0
310
834
824
[3960]
445
21
[4080]
460
48
[42 10 ]
475
10 4
[4270]
480
165
[4290]
485
228
[4290]
485
287
[4260]
480
348
[4240]
480
404
[4170]
470
461
[4060]
460
524
[4010]
455
585
[3960]
445
658
[3890]
440
731
[3820]
430
804
17 0
[2500] [3000]
205
170
[3500] [4000]
275
240
[4920]
555
17
[5090]
575
42
[5260]
595
95
[5360]
605
157
[5420]
6 10
221
[5440]
6 15
277
[5400]
6 10
338
[5380]
610
376
[5290]
6 00
448
[5150]
580
509
[5130]
580
570
[5070]
575
641
[4920]
555
712
[4890]
550
783
[5930]
670
6
[6630]
750
30
[710 0 ]
80 0
67
[ 7420]
840
125
[7490]
845
18 4
[7580]
855
238
[7590]
860
294
[7580]
855
340
[7520]
850
398
[7440]
840
456
[7100 ]
800
510
[6690]
755
5 74
[5040]
570
11
[5680]
640
39
[6180]
7 00
81
[6390]
720
141
[6480]
730
202
[6510 ]
735
257
[6490]
735
316
[6480]
730
358
[6410]
725
423
[6300]
710
482
[6190]
7 00
540
[6080]
685
608
[5940]
670
676
[5880]
665
744
[7570]
855
12
[8020]
905
53
[8450]
955
10 9
[8480]
960
165
[8660]
980
2 18
[8680]
980
271
[8670]
980
322
[8640]
975
373
[4500]
310
[2500] [3000]
170
205
[3880]
440
26
[4030]
455
62
[4120]
465
119
[4190]
475
203
[4210 ]
475
283
[4240]
480
356
[4220]
475
429
[4200 ]
475
502
[4160]
470
576
[4130]
465
645
[4100]
465
718
[4060]
460
808
[5790]
655
702
[4140]
470
18
[4600]
520
46
[4810]
545
11 6
[4990]
565
18 6
[5090]
575
258
[5100]
575
332
[5080]
575
413
[5060]
570
476
[5040]
570
542
[5000]
565
601
[4960]
560
666
[4920]
555
749
}
[3500]
240
[4000]
275
[5200]
590
32
[5530]
625
99
[5810 ]
655
167
[590 0 ]
665
236
[5950]
670
306
[5940]
670
388
[5940]
670
448
[5920]
670
5 11
[5880]
665
564
[5840]
660
624
[5790]
655
702
[5790]
655
18
[6250]
705
83
[6630]
750
148
[6710 ]
76 0
214
[6800]
770
280
[6810 ]
770
363
[6810 ]
770
421
[6790]
765
480
[6760]
765
527
[4500]
310
[6900]
780
65
[7320]
825
118
[7470]
845
18 1
[7620]
860
247
Torque [lb-in]
Nm
Speed RPM
[8520]
965
6
[9020]
1020
37
[9510 ]
1075
92
[9540]
118 0
145
[9740]
110 0
197
C-5
C-5-3
6000 Series
310 cm3/r [19.0 in3/r]
Performance Data
[250]
15
[.5]
in production.
1,9
[2]
Flow LPM [GPM]
7,5
[4]
15
[8]
30
[ 12 ]
45
[ 16 ]
61
[20]
76
[24]
91
[28]
Continuous
Peak
Intermittent
No Operation
10 6
[32]
121
[36]
136
[40]
151
[250]
15
[1]
3,8
[2]
Flow LPM [GPM]
7,5
[4]
15
[8]
30
[ 12 ]
45
[ 16 ]
61
[20]
76
[24]
91
[28]
10 6
[32]
121
[36]
136
[40]
151
[50]
18 9
[60]
227
C-5-4
18 9
[60]
[982]
110
597
227
[5 0 0 ] [ 100 0 ] [ 15 0 0 ] [2 00 0 ] [25 0 0 ] [3 00 0 ] [35 0 0 ] [4 00 0 ] [45 0 0 ]
35
70
10 5
14 0
17 0
205
275
3 10
240
[ 760 ] [1570] [3230]
85
17 5
365
4
2
1
[780] [1610] [3270]
90
18 0
370
19
18
17
[800 ] [ 1640 ] [3300]
90
18 5
375
38
38
37
[810 ] [1650] [3370]
90
18 5
380
77
76
74
[800] [1620] [3390]
90
18 5
385
11 5
11 5
112
[750] [16 00] [3380]
85
180
380
154
154
151
[680] [1580] [3360]
18 0
380
75
19 3
18 9
19 3
[620] [1520] [3280]
17 0
370
70
230
229
232
[570] [1460] [3210]
16 5
365
65
268
266
270
[530] [1420] [3140]
16 0
355
60
306
304
309
[450] [1370] [3010]
15 5
340
50
346
340
348
[380] [1320] [2880]
15 0
325
45
386
380
387
[4910]
555
16
[4970]
560
35
[5080]
575
72
[5130]
580
10 9
[5120]
580
147
[5120]
580
18 7
[5060]
570
225
[5000]
565
261
[4930]
555
299
[4840]
545
336
[4740]
535
375
[6440]
730
14
[6570]
74 0
33
[6740]
76 0
68
[6810]
770
10 5
[6820]
770
143
[6840]
775
18 2
[6780]
76 5
220
[6730]
760
256
[6640]
750
292
[6500]
730
329
[6460]
730
368
[7760] [9080]
875
1025
12
9
[8160] [9570]
920
1080
29
22
[8430] [10 050]
950
113 5
65
55
[8520] [10190]
965
1150
10 0
91
[8560] [10230]
965
115 5
132
126
[8590] [10280]
970
116 0
175
162
[8530] [10240]
965
115 5
212
204
[8480] [10200]
960
115 0
248
236
[8380] [10120]
945
114 5
282
269
[8250] [10000]
930
113 0
317
3 01
[8120]
915
359
[10590]
119 5
4
[11270]
1275
14
[ 11620]
1315
45
[11860]
1340
81
[11920]
1345
116
[11980]
1355
152
[12120]
1370
5
[12880]
1455
33
[13640]
1540
79
[1140] [2650] [4540] [6440] [8050]
130
300
515
730
910
482
475
469
460
449
[2460] [4430] [6360] [7860]
280
500
720
890
570
562
552
538
[3000]
205
[3500]
240
[5690]
645
14
[6050]
685
32
[6480]
730
73
[6730]
760
121
[6800]
770
167
[6820]
770
216
[6840]
775
260
[6820]
770
308
[6750]
765
354
[6660]
750
396
[6580]
745
441
[6670]
755
10
[7070]
800
24
[7710]
870
64
[8040]
910
111
[8150]
920
156
[8190]
925
201
[8230]
930
248
[8220]
930
295
[8170]
920
341
[8100]
915
383
[8020]
905
427
[7780]
880
4
[8260]
935
17
[8740]
985
55
[9260]
1045
99
[9400]
1060
141
[9520]
1075
184
[9560]
1080
232
[9520]
1075
276
[9440]
1065
320
[9330]
1055
360
[9220]
1040
403
[2180] [3420] [4660] [6050]
245
385
525
685
582
576
570
551
[1960] [3250] [4540] [5750]
220
365
515
650
698
691
684
661
[7440]
840
534
[7080]
800
641
[530] [ 1120] [2440]
60
125
275
6
4
1
[540] [ 1150] [2460]
60
13 0
280
24
23
22
[550] [ 1180] [2560]
60
13 5
290
48
47
45
[560] [ 1250] [2650]
65
14 0
300
96
95
91
[570] [1260] [2690]
65
140
305
144
143
140
[540] [1230] [2660]
60
140
300
193
192
188
[510] [1200] [2630]
60
13 5
295
242
241
236
[480] [1160] [260]
55
130
295
290
289
282
[420] [1130] [2570]
45
130
290
339
336
333
[360] [1100] [2510]
40
125
285
388
384
381
[300] [1060] [2440]
35
120
275
436
430
421
[270] [1020] [2400]
30
115
270
485
478
466
[50]
390 cm3/r [23.9 in3/r]
[500] [1000 ]
35
70
[14490]
1635
1
[14480]
1635
21
[1500] [2000 ] [2500]
10 5
140
170
[3620]
4 10
20
[3800]
430
42
[3970]
450
87
[4050]
460
135
[4060]
460
18 4
[4040]
455
232
[4020]
455
279
[3990]
450
328
[3920]
445
375
[3830]
435
416
[3780]
425
461
[5750]
650
661
[4780]
540
17
[5030]
570
38
[5280]
595
81
[5420]
610
129
[5450]
615
178
[5450]
615
226
[5440]
615
273
[5420]
610
320
[5330]
6 00
368
[5220]
590
4 10
[5150]
580
456
}
Torque [lb-in]
Nm
Speed RPM
[4000]
275
[4500]
310
[9070]
1025
10
[9770]
110 5
46
[10490]
118 5
88
[10660]
1205
126
[10840]
1225
167
[10900]
1230
215
[10840]
1225
257
[9530]
1075
3
[10990]
1240
35
[118 00]
1335
76
[11990]
1355
109
6000 Series
490 cm3/r [30.0 in3/r]
Performance Data
[250]
15
[1]
in production.
3,8
[2]
Flow LPM [GPM]
7,5
[4]
15
[8]
30
[ 12 ]
45
[ 16 ]
61
[20]
76
[24]
Continuous
91
[28]
Peak
Intermittent
10 6
[32]
No Operation
121
[36]
136
[40]
151
[50]
625 cm3/r [38.0 in3/r]
[1]
3,8
[2]
Flow LPM [GPM]
7,5
[4]
15
[8]
30
[ 12 ]
45
[16 ]
61
[20]
76
[24]
91
[28]
10 6
[32]
121
[36]
136
[40]
151
[50]
18 9
[60]
227
[250]
15
[500]
35
[1000]
70
[1500]
105
[1060]
120
5
[1090]
125
12
[1145]
13 0
24
[1195]
135
45
[1200]
13 5
72
[1120]
125
94
[1050]
120
120
[950]
105
144
[855]
95
169
[730]
80
19 3
[555]
65
217
[380]
45
241
[2205]
250
5
[2300]
260
12
[2450]
275
24
[2600]
295
45
[2600]
295
72
[2530]
285
94
[2465]
280
119
[2365]
265
143
[2255]
255
168
[2140]
240
19 2
[1965]
220
216
[1790]
2 00
240
[4515 ]
510
4
[4720]
535
13
[5052]
570
24
[5350]
605
44
[5390]
610
71
[5340]
605
92
[5285]
595
117
[5180]
585
140
[5080]
575
165
[4960]
560
18 8
[4780]
540
213
[4600]
520
238
[6690]
755
2
[7025]
795
10
[7520]
850
21
[8195]
925
42
[8145]
920
68
[8105]
915
89
[8080]
915
115
[7990]
905
138
[7915]
895
162
[7775]
880
185
[7585]
855
2 10
[7395]
835
236
[2000]
140
[9360]
1060
6
[9410]
1065
16
[11220]
1270
37
[11770]
1330
64
[11740]
1325
85
[11725]
1325
110
[11705]
1320
132
[11640]
1315
156
[11505]
13 00
179
[2500]
170
[1010]
115
7
[1020]
115
15
[1030]
115
30
[1020]
115
60
[1000]
115
91
[110]
960
122
[900]
100
153
[850]
95
184
[740]
85
215
[690]
80
245
[670]
75
276
[570]
65
307
18 9
[60]
[3000]
205
[3200]
221
227
[2860]
325
454
[12700]
1434
13
[13100]
1480
35
[13000]
1469
60
[13000]
1469
83
[15800]
1785
32
[15700]
1774
56
[500] [1000]
35
70
[3000]
205
[1500] [2000]
10 5
14 0
[2500]
170
[6140]
695
3
[6280]
710
12
[6410 ]
725
28
[6490]
735
57
[6500]
735
87
[6480]
730
118
[6420]
725
147
[6390]
720
18 0
[6290]
710
208
[6190]
700
237
[6080]
685
265
[5970]
675
295
[8350]
945
11
[8500]
960
27
[8620]
975
54
[8650]
975
84
[8650]
975
114
[8620]
975
144
[8580]
970
176
[8500]
960
204
[8420]
950
232
[8340]
940
260
[8140]
920
290
[10420] [12140]
117 5
1370
8
3
[10590] [12500]
119 5
1410
25
21
[10740] [12800 ]
1215
1445
51
45
[10800] [12890]
1220
1455
79
71
[10820] [12900]
1220
1460
10 9
100
[10820]
1220
139
[10770]
1215
171
[10720]
1210
198
[10660]
1205
226
[10420]
1175
255
[10180]
115 0
284
[1140] [3240] [5220]
365
590
130
379
369
382
[2860] [4860]
325
550
454
442
[ 7620]
860
362
[7140]
805
435
[1200]
235
7
[2110]
240
14
[2100 ]
235
30
[2090]
235
60
[2080]
235
91
[2060]
235
122
[1980]
225
152
[1930]
220
18 4
[1840]
210
214
[1710]
195
244
[1560]
175
275
[14 00]
16 0
306
}
[4260]
480
5
[4270]
480
13
[4280]
485
29
[4290]
485
59
[4290]
485
89
[4260]
480
121
[4180]
470
150
[4150]
470
18 1
[4070]
460
2 11
[3970]
450
241
[3860]
435
272
[3750]
425
303
[3500]
240
[4000]
275
[14580]
1645
17
[14930]
1685
38
[16670]
1885
12
Torque [lb-in]
Nm
Speed RPM
[16800]
1898
30
C-5
[4180] [6985]
470
790
296
290
[3800] [6600]
430
745
353
345
C-5-5
6000 Series
735 cm 3 /r [45.0 in
Performance Data
[1]
in production.
3,8
[2]
Fl ow LPM [GPM]
7,5
[4]
15
[8]
30
[ 12 ]
45
[ 16 ]
61
[20]
76
[24]
91
[28]
Peak
Continuous
Intermittent
10 6
[32]
No Operation
121
[36]
136
[40]
151
[250]
15
[500 ]
35
[750]
50
[1000]
70
[1250]
85
[1311]
14 8
4
[1340]
151
10
[1253]
14 2
20
[1290]
146
40
[1277]
144
61
[1196]
13 5
82
[1092]
123
10 2
[1206]
13 6
123
[1083]
122
145
[950]
10 7
163
[726]
82
18 4
[515]
58
203
[2775]
314
4
[2856]
323
10
[2854]
322
20
[2889]
326
39
[2821]
3 19
60
[2753]
311
80
[2794]
316
101
[2556]
289
122
[2338]
264
142
[2110]
238
162
[1845]
208
18 3
[2227]
252
202
[4200]
475
3
[4535]
512
10
[4363]
493
19
[4540]
513
38
[4528]
512
59
[4478]
506
79
[4320]
488
101
[4162]
470
120
[4040]
456
141
[3795]
429
162
[3517]
397
18 2
[3270]
369
202
[5480]
619
3
[5809]
656
10
[5813]
657
18
[6130]
693
38
[6180]
698
58
[6148]
695
78
[6021]
680
99
[5871]
663
119
[5666]
640
139
[5457]
6 17
159
[5223]
590
18 1
[4965]
561
2 01
[7000]
791
2
[7551]
853
9
[7272]
822
17
[7703]
870
37
[7795]
881
57
[7768]
878
77
[7697]
870
97
[7564]
855
118
[7365]
832
137
[7122]
805
159
[6853]
774
179
[6672]
754
19 9
[3869]
437
254
[4148]
469
252
[4856]
549
303
[5850]
661
250
[6604]
74 6
301
[50]
805 cm 3 /r [49.0 in
[1]
3,8
[2]
Fl ow LPM [GPM]
7,5
[4]
15
[8]
30
[ 12 ]
45
[ 16 ]
61
[20]
76
[24]
91
[28]
10 6
[32]
121
[36]
136
[40]
151
[50]
18 9
[60]
227
C-5-6
[250]
15
[500]
35
[750]
50
[1000]
70
[1455]
164
4
[1483]
16 8
9
[1547]
175
19
[1599]
181
35
[1599]
181
56
[1543]
174
73
[1457]
16 5
93
[1352]
15 3
11 2
[1213 ]
137
131
[1075]
121
150
[823]
93
168
[592]
67
187
[3100]
350
4
[3173]
359
9
[3331]
376
19
[3473]
392
35
[3469]
392
56
[3395]
384
73
[3312]
3 74
92
[3183]
360
112
[3055]
345
131
[2907]
328
149
[2692]
304
168
[2477]
280
18 6
[4680]
529
2
[5121]
579
9
[5292]
598
18
[5415]
612
34
[5415]
612
55
[5357]
605
72
[5292]
598
91
[5088]
575
111
[5047]
570
131
[4884]
552
149
[4663]
527
168
[4426]
5 00
18 6
[6031]
681
2
[6432]
727
8
[6744]
762
17
[7039]
795
33
[7093]
8 01
53
[7032]
794
70
[6968]
787
89
[6811]
76 9
110
[6713]
758
129
[6546]
740
146
[6320]
714
167
[6085]
688
18 5
[2730]
308
234
[4214] [5849]
4 76
661
233
231
[3806] [5459]
430
617
280
277
[1250]
85
[1500]
105
18 9
[60]
3 /r]
[1750]
120
[7799]
881
1
[8510]
[9633] [ 11319 ]
961
1088
1279
7
6
5
[8714] [10075] [11352]
984
1138
1283
16
15
14
[8934] [10629] [11842]
1338
10 09
1201
29
32
31
[9024] [10658] [12283]
1388
1020
1204
50
53
52
[8983] [10640] [12010]
1357
10 15
1202
67
69
68
[8943] [10583] [12146]
1372
1010
119 6
86
88
87
[8812] [10411]
996
1176
108
10 6
[8681] [10411]
981
1176
128
127
[8395] [10060]
113 7
949
144
145
[8118]
9 17
165
[7832]
885
184
227
[2000]
140
[2250]
15 5
[2500]
170
[12127]
1370
5
[12539]
1417
12
[14004]
1582
29
[13726]
1551
50
[14564]
1645
11
[15441]
174 5
28
[16377]
1850
10
[7603]
859
230
[7407]
837
275
[6604]
746
301
}
Torque [lb-in]
Nm
Speed RPM
3 /r]
[1750]
120
[2000]
140
[2250]
15 5
[2500]
170
[8685] [ 10182]
981
115 0
6
7
[8714] [10135]
985
114 5
16
14
[9202] [10666]
1040
1205
37
35
[9338] [10877]
1055
1229
56
54
[9376] [10984]
1241
1059
74
76
[10907]
[9311]
1232
1052
93
96
[9289]
1049
116
[9022]
1019
135
[8828]
997
156
[11121]
1257
5
[11537]
1303
13
[12192]
1378
33
[12419]
1403
52
[12970]
1465
11
[ 13713]
1549
32
[15040]
1699
11
[1500]
105
6000 Series
985 cm3/r [60.0 in3/r]
D Pressure Bar [PSI]
Performance Data
[1]
3,8
[2]
7,5
[4]
Flow LPM [GPM]
in production.
15
[8]
30
[ 12 ]
45
[ 16 ]
61
[20]
76
[24]
Continuous
Peak
Intermittent
No Operation
91
[28]
10 6
[32]
121
[36]
136
[40]
151
[50]
18 9
[60]
[250]
15
[500]
35
[750]
50
[1890]
215
3
[1910]
215
8
[1980]
225
15
[2030]
230
30
[2020]
230
45
[2010]
225
61
[1910]
21 5
77
[1810]
205
92
[1620]
18 5
10 7
[1480]
165
123
[1140]
13 0
138
[850]
95
153
[4110]
465
3
[4 140]
470
8
[4290]
485
15
[4400]
495
30
[4390]
495
45
[4320]
490
61
[4220]
475
77
[4060]
460
92
[3920]
445
10 7
[3740]
425
123
[3490]
395
138
[3240]
365
153
[5730]
645
2
[6270]
710
7
[6480]
775
15
[6630]
750
30
[6630]
750
45
[6560]
740
61
[6480]
730
76
[6230]
705
92
[6180]
700
107
[5980]
675
122
[5710]
645
138
[5420]
6 10
152
[2960]
325
191
[5160] [7350]
585
830
19 0
18 9
[4660] [7160]
525
810
230
229
227
[7160]
8 10
229
}
[1000]
70
[1250]
85
[ 7640] [9550]
865
1080
2
1
[8300] [10420]
940
1175
7
6
[8540] [10670]
965
1205
14
14
[8790] [10940]
995
1235
29
28
[8860] [11050]
1000
1250
44
43
[8790] [11000]
995
1245
60
59
[8720] [10950]
985
1235
76
75
[8500] [10790]
960
1220
91
90
[8420] [10630]
950
1200
10 6
10 5
[8200] [10280]
925
116 0
121
120
[7930]
[9940]
895
1125
137
135
[7640]
[9590]
865
1085
151
150
[1500]
10 5
[1750]
120
[2000]
140
[12500]
1410
5
[12800]
1445
13
[13090]
1480
27
[13240]
1495
42
[13260]
1500
58
[13160]
1485
74
[12990]
1470
89
[12820]
1450
103
[13860]
1565
4
[13900]
1570
13
[14500]
1640
26
[15040]
1700
41
[14920]
1685
3
[15850]
1790
12
[16580]
1875
25
[9310]
1050
188
[9070]
1025
226
Torque [lb-in]
Nm
Speed RPM
C-5
C-5-7
6000 Series
Ports
G 1 (BSP) Staggered Ports (2)
1 5/16 UN-2B SAE O-ring Staggered Ports (2) with Shuttle
Dimensions
Standard Mount
Standard Mount
Y Max.
X
Port B
Case Drain
Port
Standard SAE CC Flange
24,6/24,1
[.97/.95]
13,59/12,8
[.535/.505]
14,53/14,14
[.572/.557]
Dia. Thru (4)
127,00/126,87
[5.000/4.995] DIa.
114,5
[4.508]
Square
146,8 [5.78]
Square Max.
161,9 [6.375]
Dia. Bolt Circle
147,4 [5.80] Max.
Standard Motor Mount Dimensions
Displacement
cm3/r [in3/r]
X
mm [inch]
Y
mm [inch]
195 [11.9]
245 [15.0]
310 [19.0]
390 [23.9]
490 [30.0]
625 [38.0]
985 [60.0]
187,5 [ 7.38]
193,0 [ 7.60]
200,4 [ 7.89]
209,0 [ 8.23]
220,2 [ 8.67]
235,0 [ 9.25]
274,6 [10.81]
270,0 [10.63]
275,6 [10.85]
283,0 [11.14]
291,6 [11.48]
302,8 [11.92]
317,5 [12.50]
357,1 [14.06]
C-5-8
6000 Series
Ports
Dimensions
Wheel Mount
Wheel Mount
Y Max.
Port B
X
Case Drain
Port
98,6/97,0
[3.88/3.82]
139,70/139,57
[5.500/5.495] Dia.
166,4 [6.55]
Square Max.
127,00/126,87
[5.000/4.995] Dia.
130,21
[5.126]
Max.
C-5
22,6/22,1
[.89/.87]
7,74
[.305] Min.
17,3/16,8
[.68/.66]
14,53/14,14
[.572/.557] Thru (4)
184,12 [7.250]
Dia. Bolt Circle
Wheel Mount Motor dimensions
Displacement
cm3/r [in3/r]
X
mm [inch]
Y
mm [inch]
195 [11.9]
245 [15.0]
310 [19.0]
390 [23.9]
490 [30.0]
625 [38.0]
985 [60.0]
102,6 [4.04]
108,2 [4.26]
115,6 [4.55]
124,5 [4.90]
135,4 [5.33]
150,1 [5.91]
189,7 [7.47]
185,2 [7.29]
190,8 [7.51]
198,1 [7.80]
207,1 [8.15]
217,9 [8.58]
232,7 [9.16]
272,5 [10.73]
C-5-9
6000 Series
Ports
Dimensions
Global Mount (ISO)
Global Mount (ISO)
Y Max.
X
20,3/19,8
[.80/.78]
Port B
38,7/37,7
[1.525/1.485]
159,99/159,94
[6.299/6.297]
Pilot Dia.
179,6 [7.07] Max.
179,6
[7.07]
Max.
141,43
[5.568]
(4)
Case Drain
Port
18,21/17,83
[.717/.702]
Dia. Thru (4)
50 mm Dia. Straight Shaft
200,00 [7.874]
Dia. Bolt Circle
124,5/120,4
[4.90/4.74]
70,26/69,75
[2.766/2.746]
8,4/4,6
[.33/.18]
14,000/13,957
[.5512/.5495]
8,992/8,890
[.3540/.3500]
53,49/52,70
[2.106/2.075]
79,2 [3.12]
Max. Coupling
Length
C-5-10
50,000/49,974
[1.9685/1.9675]
M12 x 1,75
25,0 [.98] Min.
Depth
Global Mount Motor Dimensions
Displacement
cm3/r [in3/r]
X
mm [inch]
Y
mm [inch]
310 [19.0]
390 [24.0]
490 [30.0]
625 [38.0]
800 [45.0]
800 [49.0]
985 [60.0]
182,4 [ 7.18]
191,0 [ 7.52]
202,2 [ 7.96]
216,9 [ 8.54]
229,4 [ 9.03]
236,7 [ 9.32]
256,5 [10.10]
264,9 [10.43]
273,6 [10.77]
284,7 [11.21]
299,5 [11.79]
312,2 [12.29]
319,3 [12.57]
339,1 [13.35]
6000 Series
Ports
Dimensions
Bearlingless
Bearingless
Y Max.
Y Max.
X
Port B
Port B
161,9 [6.375] 161,9 [6.375]
Dia. Bolt Circle
Dia. Bolt Circle
X
114,5
[4.508]
Squa re
114,5
[4.508]
Squa re
14.50/14,14 14.50/14,14
[.572/.557] [.572/.557]
127,00/126,87127,00/126,87
[5.000/4.995][5.000/4.995]
Dia.
Dia.
45º
45º
Case Drain Case Drain
Port
Port
147,6 [5.81] Max.
147,6Square
[5.81] Max. Square
24,2/21,0
[.95/.83]
24,2/21,0
[.95/.83]
12,7/12,1
[.50/.48]
Face Seal Face Seal
or O-ring Sealor O-ring Seal
12,7/12,1
[.50/.48]
Case Flow Holes
Case(2)Flow Holes (2)
Note: SimilarNote:
to Similar to
SAE C Type SAE C Type
Mounting Flange
Mounting Flange
For 6000 bearingless motor
application information, contact
your Eaton representative (mating
C
coupling blanks available from
Eaton Hydraulics).
Note:
After machining blank, part
must be hardened per Eaton
specification.
Displacement
cm3/r [in3/r]
X
mm [inch]
Y
mm [inch]
195 [11.9]
245 [15.0]
310 [19.0]
390 [23.9]
490 [30.0]
625 [38.0]
985 [60.0]
105,4 [4.15]
111,0 [4.37]
118,4 [4.66]
127,3 [5.01]
138,2 [5.44]
152,9 [6.02]
192,8 [7.59]
188,0 [7.40]
193,5 [7.62]
200,9 [7.91]
209,6 [8.25]
220,7 [8.69]
235,5 [9.27]
275,1 [10.83]
C 47,2 [1.86] Dia.
D 111,5 [4.39] Max.
E 106,4 [4.19] Full Form Dia.
F 6,9 [ .27] Min. Full Form Dia.
G 10,2 [ .40] Min.
H 86,1 [3.39] Max.
J 66,5 [2.62] Dia.
J
C
C-5
E
D
F
E
D
F
G
H
G
H
J
Mating Coupling
Blank
Mating
Coupling Blank
Eaton Part No.Eaton
12778-002
Part No. 12778-002
C-5-11
6000 Series
HRc with case depth (to 50HRc) of 0,076
- 1,02 [.030 - .040] (dimensions apply after
heat treat).
Bearingless
be provided.
5 Similar to SAE “C” Four Bolt Flange..
[1.9689 - 1.9700] ID by 60,051 - 60,079
[2.3642 - 2.3653] O.D. (Oilite bronze sleeve
bearing).
16
49,848/49,822
1.9625/1.9615
14,2/12,7
[.56/.50]
0,13[.005]
1,5/0,5
[.06/.02]
A
-D30°
15°
1,8/0,5
[.07/.02]
3
52,37
[2.062]
Dia. Min.
40,1/39,6
[1.58/1.56]
Dia.
R 1,8/1,2
[.07/.05]
24,6/24,1
[.97/.95]
1,5/0,8
[.06/.03]
Case Flow
5,1/4,6 [.20/.18] Dia. 2
(2) Thru Oil Hole
6,8/6,4
[.27/.25]
81,8/80,7
[3.22/3.18]
-A6
0,13 [.005] A
Case Flow
R 0,5 [.02] Max.
5
4
-B-
9,4/8,4
[.37/.33]
69,3/68,1
[2.73/.2.68]
Coupling Depth
Circular
Major
Finish
Finish
Tip R .
Minor
C-5-12
Fillet R.
Pitch
Form
Spline Pitch................................................................................................. 8.5/17
Pressure Angle................................................................................................30°
Number of teeth............................................................................................... 12
Class of Fit................................................................................................... Ref. 5
Type of Fit...................................................................................................... Side
| 0,20 [.008] | D
Major Diameter....................................39,17 [1.542] Max. 38,97 [1.534] Min..
Fillet Radius.................................................................... 0,64 - 0,76 [.025 - .030]
Tip Radius....................................................................... 0,25 - 0,51 [.010 - .020]
Finish..........................................................................................................1,6 (63)
Lead Variation.................................................................................0,013 [.0005]
Maximum Actual......................................................................5,898 [.2322]
Dimension Between Two Pins........... Ref. 26,929 - 27,084 [1.0602 - 1.0663]
Pin Diameter...........................................6,223 [.2450] Pins to Have 4,0 [.160]
.
6000 Series
Dimensions
Shafts Splined
1 3/4 Inch Tapered
1 1/2 Inch Straight
1328 [11750]
Max. Torque
Nm [lb-in]
9,56/9,52
1328 [11750]
[.376/.375]
Max. Torque
Nm [lb-in]
1328 [11750]
9,56/9,52
Max. Torque
[.376/.375]
Nm [lb-in]
3/8-16 UNC x
9,56/9,52
18,5 [.73]
Deep
[.376/.375]
78,2/76,2 [3.08/3.00]
End of Shaft to
42,0/40,6 78,2/76,2 [3.08/3.00]
[1.65/1.60] End of Shaft to
78,2/76,2 [3.08/3.00]
42,0/40,6
[1.65/1.60] End of Shaft to
42,0/40,6
[1.65/1.60]
42,40/42,13
[1.669/1.659]
3/8-16 UNC x
18,5 [.73] Deep
38,10/38,04
[1.500/1.498]
42,40/42,13
Dia.
[1.669/1.659]
3/8-16 UNC x
18,5 [.73] Deep
38,10/38,04
42,40/42,13
[1.500/1.498]
[1.669/1.659]
Dia.
56,7
[2.23]
Max. Coupling
56,7
[2.23]
Max. Coupling
56,7 [3.08/3.00]
78,2/76,2
[2.23]
38,10/38,04
End ofMax.
ShaftCoupling
to
[1.500/1.498]
1328
[11750]
1 1/2 Inch 17 Tooth Splined
Dia.
Max. Torque
Nm [lb-in]
40,3 [1.59]
78,2/76,2 [3.08/3.00]
Min. Full Spline End of Shaft to
3/8-16
UNC x
1328
[11750]
18,5
[.73] Deep
Max.
Torque
78,2/76,2 [3.08/3.00]
Nm [lb-in]
40,3 [1.59]
Min. Full Spline End of Shaft to
1328 [11750]
3/8-16 UNC x
Max.
18,5Torque
[.73] Deep
Nm [lb-in]
40,3 [1.59]
Min. Full
Spline
External
Involute
38,10
[1.500]
3/8-16 UNC x
Spline,
12.24
DP
Dia.
Ref.
18,5 [.73] Deep
56,7
17 Tooth 30 P.A.
[2.23]
Flat Root Side Fit
Max. Coupling
per
ANSI
B92.1,
1976
External Involute
38,10 [1.500]
Spline, 12.24 DP
Dia. Ref.
56,7
17 Tooth 30 P.A.
[2.23]
Flat Root Side Fit
94,0/91,9
[3.70/3.62]
External
38,10 [1.500]
Max.
Coupling
per
ANSIInvolute
B92.1, 1976
Spline,
12.24 DP
Dia. Ref. End of Shaft to
1328 [11750]
17
Tooth
30 P.A.12,000/11,957
Mounting 56,7
Surface (Std)
Max.
Torque
[2.23]
Flat Root Side Fit[.4724/.4708]
Nm
[lb-in]
Max.[.36/.18]
Coupling
per ANSI B92.1, 1976
9,2/4,5
94,0/91,9
[3.70/3.62]
End of Shaft to
1328 [11750]
8,000/7,910 12,000/11,957
63,7/62,2
Mounting
Surface (Std)
40Max.
mm
Straight
Torque
[.3149/.3115]
[2.51/2.45]
[.4724/.4708]
94,0/91,9 [3.70/3.62]
Nm [lb-in]
9,2/4,5 [.36/.18]
End of Shaft to
1328 [11750]
Mounting
Surface (Std)
Max.
Torque 12,000/11,957
8,000/7,910
63,7/62,2
[.4724/.4708]
[.3149/.3115]
[2.51/2.45]
Nm
[lb-in]
9,2/4,5 [.36/.18]
M12 x 1,75 -6H
8,000/7,910
25 mm [.984] Deep
[.3149/.3115]
40,018/39,992
43,03/42,72
[1.5755/1.5745]
[1.694/1.682]
M12 x 1,75 -6H
25 mm [.984] Deep
40,018/39,992
43,03/42,72
[1.694/1.682]
M12 x 1,75 -6H[1.5755/1.5745]
25 mm [.984] Deep
40,018/39,992
43,03/42,72
[1.5755/1.5745]
[1.694/1.682]
63,7/62,2
75,6
[2.98]
[2.51/2.45]
Max. Coupling
177,8/175,0 [7.00/6.89]
End of Shaft to Mounting Surface (Whl)
2107 [18650]
Max. Torque
Nm [lb-in]
2107 [18650]
1-1/4-18
UNEF-2A
Max. Torque
Nm [lb-in]
2107 [18650]
4,1 [.16]
Max. Torque
Dia. Thru
1-1/4-18
UNEF-2A
Nm [lb-in]
31,7 [1.25]
177,8/175,0 [7.00/6.89]
31,7 [1.25]
177,8/175,0 [7.00/6.89]
31,7 [1.25]
44.45 4,1 [.16]
[1.750]
Dia.Thru
1-1/4-18
UNEF-2A
77,0 [3.03]
Dia.
125,00 0,174,1
Taper
[.16]per Mete r
44.45 Taper
[1.500±.002
per Foot]
Dia.
[1.750] Dia.Thru
77,0 [3.03]
SAE J501 Standard Tapered Shaf5,54/5,20
t
125,0044.45
0,17 Taper per Mete r [.218/.205]
[1.500±.002
[1.750]Taper
Dia. per Foot] 77,0 [3.03]
SAE J501 Standard Tapered Shaf5,54/5,20
t
125,00 0,17 Taper per Mete r [.218/.205]
11,138/11,112
[.4385/.4375]
11,138/11,112
[.4385/.4375]
11,138/11,112
[.4385/.4375]
Tapered Shaft HubHub
Data
(645 Nm [475 lb-ft] Dry)
(510 Nm [375 lb-ft] Lub) Hub
align
the slotted nut
with:
Recommended
Torque
the
Crosshole.
(645Shaft
Nm [475
lb-ft] Dry) Hub
(510 Nm [375 lb-ft] Lub)
Recommended
Torque
align
the slotted nut
with:
(645Shaft
Nm [475
lb-ft] Dry)
the
Crosshole.
60,17/57,78
(510 Nm [375 lb-ft] Lub)
Plus Torque required[2.369/2.275]
t o
align the slotted nut with
60,17/57,78
[2.369/2.275]
5,54/5,20
[.218/.205]
60,17/57,78
[2.369/2.275]
C-5
11,2 [.44]
55,4 [2.18]
Slotted Hexagon Nut
1-1/4-18 UNEF-2B
4,1 [.16]
11,2 [.44]
55,4 [2.18]
4,1 [.16]
1-1/4-18 UNEF-2B
30º
11,2 [.44]
55,4 [2.18]
30º4,1 [.16]
1-1/4-18 UNEF-2B
75,6 [2.98]
Max. Coupling
30º
30º
75,6 [2.98]
Max. Coupling
30º
30º
15,7 [.62]
15,7 [.62]
15,7 [.62]
C-5-13
6000 Series
locations with an external
thrust load of 454 kg
[1000 lb]. The maximum
allowable thrust load is
908 kg [2000 lb]. Note:
push outward on the shaft
at 109 kg/7 Bar [241 lb/100
PSI].
Thrust Load
Standard Motor
kg
[lb]
[10000]
[ 8000]
[ 6000]
2000
[ 2000]
1000
RPM
50
100
200
300
400
500
600
700
800
1.23
1.00
0.81
0.72
0.66
0.62
0.58
0.56
0.54
0
0
mm
[inch]
-100 -80 -60 -40 -20 0 20 40 60 80 100
[-4] [-3] [-2] [-1]
[1] [2] [3] [4]
Wheel Motor Tapered Shaft
kg
[ 8000]
[ 6000]
4000
3000
[ 4000]
2000
[ 2000]
1000
0
mm
0
-20 0 20 40 60 80 100 120 140 160 180 200
[inch] [-1]
0
[1] [2] [3] [4] [5]
Mounting Surface
C-5-14
0
Mounting Surface
[10000]
below.
3000
[ 4000]
[lb]
Max. Axial Loads
908 kg [2000 lb]
4000
[6] [7] [8]
6000 Series
Allowable case pressure is
highest at low shaft speeds.
Consequently, motor life
will be shortened if case
pressure exceeds these
ratings (acceptability may
vary with application).
limitation chart.
100
Case
Pressure
Bar
50
[PSI]
Case Drain
Required
[1000]
Optional
[ 500]
Optional
0
0
0
100 200
0
300
400
500
600
700
800
900
Speed RPM
C-5
C-5-15
6000 Series
Dimensions
Ports
1 5/16 -12 O-ring Ports (2) or
G 1 (BSP) Ports (2)
4 Bolt 3/4 Inch Split Flange
Ports to Fit
SAE J518c (2)
Except for 20,0
[.79] Min. Thd. Dp.
G 1/4 (BSP) Port Case Drain
Port B
Port A
G 1/4 (BSP) Port Case Drain
Port B
13,8/10,6
[.54/.42]
35,9/34,7
[1.414/1.366]
Port A
19,4/18,7
[.765/.735]
17°
Port A
19,4/18,7
[.765/.735]
19,4/18,7 [.765/.735]
13,8/10,6
[.54/.42]
58,0/56,3
35,9/34,7
[2.28/2.22]
[1.414/1.366]
19,4/18,7 [.765/.735]
17°
65,8
[2.59]
Max.
77,7
[3.06]
Max.
47,63
[1.875]
23,9 [.94]
77,7
[3.06]
Max.
47,63
[1.875]
Port B
65,8
[2.59]
Max.
81,8
[3.22]
Max.
7/16-20 UNF O-ring
Port Case Drain
7/16-20 UNF O-ring
Port
Case Drain
13,8/10,6
[.54/.42]
11,2 [.44]
13,8/10,6
[.54/.42]
22,23 [.875]
45°
20,7/17,4
9/16-18 UNF O-ring
[.80/.70]
54,9 [2.16]
44,2/39,6
[1.74/1.56]
9/16-18 UNF O-ring
4,4/3,0
[.17/.12]
Port A
35,9/34,7
[1.414/1.366]
19,4/18,7
[.765/.735]
81,8
[3.22]
Max.
Port A
19,4/18,7
4,4/3,0
[.17/.12]
[.765/.735]
17°
35,9/34,7
[1.414/1.366]
58,0/56,3
19,4/18,7
[2.28/2.22]
[.765/.735]
19,4/18,7
[.765/.735]
17°
58,0/56,3
[2.28/2.22]
20,1 [.79] Max.
66,0
[2.60]
Max.
66,0
[2.60]
Max.
C-5-16
77,0
[3.03]
Max.
11,2 [.44]
22,23 [.875]
45°
1 5/16 -12 O-ring Ports (2) with Shuttle
Port B
65,8
[2.59]
Max.
93,7
[3.69]
Max.
65,8
[2.59]
Max.
93,7
[3.69]
Max.
77,0
[3.03]
Max.
54,9 [2.16]
20,7/17,4
[.80/.70]
44,2/39,6
[1.74/1.56]
65,8
[2.59]
Max.
Port B
23,9 [.94]
Port A
58,0/56,3
[2.28/2.22]
65,8
[2.59]
Max.
Ports to Fit
SAE J518c (2)
Except for 20,0
[.79] Min. Thd. Dp.
Port B
20,1 [.79] Max.
79,5
[3.13]
Max.
79,5
[3.13]
Max.
6000 Series
Note:
in the charts above: Use
product in detail.
Product Numbers
Mounting
Shaft
Port Size
112-, 113-, or 114 - plus four
Example 114-1047.
195
[11.9]
245
[ 15.0]
310
[19.0]
390
[23.9]
490
[30.0]
625
[38.0]
735*
[45.0]
805*
[49.0]
985
[60.0]
1 1/2 inch Straight
1 5/16 O-ring
112-1064
-1065
-1066
-1067
-1068
-1107
-1145
—
-1069
40 mm Straight Standard
1 1/2 Inch
G 1 (BSP) 112-1094 -1095
-1096
-1097
-1098
—
—
—
-1099
1 5/16 O-ring
112-1058
-1060
-1061
-1062
-1109
1163
—
-1063
17 T Splined
G 1 (BSP) 112-1088-1089-1090-1091-1092—
—
—
-1093
Wheel
40 mm Straight G 1 (BSP) 113-1082 -1083
-1084
-1085
-1086
-1100
—
—
-1087
Motor
1-3/4 Inch Tapered 1 5/16 O-ring
113-1070
-1071
-1072
-1073
-1074
-1093
—
—
-1075
1 5/16 O-ring
114-1031
-1032
-1033
-1034
-1035
-1055
—
—
-1036
G 1 (BSP) 114-1043-1044-1045-1046-1047—
—
—
-1048
Bearingless
-1059
*New release
114-1047
112- plus four digit number
from charts for complete
product number—
Example 112-1215.
Mounting Type - Standard (Code H), 4 Bolt:
• 160,0 [6.30] Pilot Dia.
• 18,01 [.709] Dia. Mounting Holes
• 200,0 [7.87] Dia. Bolt Circle Output Shaft - Straight (Code 21)
Ports - G1 (BSP) Staggered G 1/4 Case Drain (Code C)
Paint - Low Gloss Black (Code A) Mounting
Shaft
Port Size
310
[19.0]
Standard 50 mm Straight G 1 (BSP) 390
[23.9]
112-1217 -1218
490
[30.0]
625
[38.0]
735
[45.0]
805
[49.0]
985
[60.0]
-1215
-1216
-1247 -1219
-1220
C-5
112-1215
C-5-17
6000 Series
identify all of the configuration options for the 6000 Series
desired features. All 30-digits of the code must be present
when ordering. You may want to photocopy the matrix
below to ensure that each number is entered in the correct
box.
Model Code
M
0 6
* * *
* *
* *
* *
* *
1
2 3
4 5 6
7 8
9 10
11 12
13 14
1 Product
M – Motor
2 , 3 Series
06 – 6000 Series
cm3/r [in3/r]
120 – 195.8 [11.95]
150 – 246.5 [15.04]
190 – 312.0 [19.04]
239 – 391.7 [23.90]
300 – 491.4 [29.99]
381 – 624.2 [38.09]
450 – 737.4 [45.00]
490 – 803.4 [49.03]
600 – 982.7 [59.97]
7 , 8 Mounting Type
AA – Bearingless, 4 Bolt:
14,35 [.565] Dia. Holes
AB – Standard, 4 Bolt (SAE
CC): 127,0 [5.00] Pilot Dia.
and 14,35 [.565] Dia. Holes
on 162,0 [6.38] Dia. B.C.
AC – Wheel, 4 Bolt 139,7
[.565] Dia. Holes on 184,2
AD – Standard, 4 Bolt, (SAE
D): 152,4 [6.00] Pilot Dia.
15.24 [.600] Dia. Holes on
228.6 [9.00] Dia. Bolt Circle
(SAE D) with O-Ring Groove
to Accept ARP-163 O-Ring
AH – Standard, 4 Bolt: 10.0
[6.30] Pilot Dia. 18,01 [.709]
Dia. Holes on 200.0 [7.87]
Dia. Bolt Circle.
AL - Wheel, 4 Bolt: 160.0
[6.30] Pilot Dia. with 5.8 [.23]
Pilot Length and 18.00 [.709]
Dia. Holes on 200.0 [7.874]
Bolt Circle (ISO Compatible)
C-5-18
* *
0 0
*
*
0 0
* *
* *
0 0
F
15
16 17
18
19
20 21
22 23
26 27
28 29
30
9 , 10 Output Shaft
Description
01 – 38,10 [1.50) Dia.
Straight Shaft with .375-16
UNC-2B Thread in End, 9,52
[.375] Sq x 41,28 [1.625]
Straight Key
02 – 44,45 [1.75] Dia. .125:1
J501 with 1.25-18 UNEF-2A
Threaded Shaft End, 11,11
[.4375] Sq. x 31,8 [1.25]
Straight Key
03 – 38,10 [1.50] Dia. Flat
12/24 DP 30 DEG. Involute
Spline with .375-16 UNC-2B
Thread in end 40,4 [1.59]
Minimum Full Spline
Length
04 – 40,00 [1.575] Dia.
1.75-6H Thread in End, 12W
x 8H x 63L [.472W x .313H x
2.480L] Key
12– 49,99 [1.968] Dia.
1.75-6H Thread in End, 14W
x 9H x 70L [.550W x .354H x
2.756L] Key
15 – 60mm Dia. 10:1 Tapered
Shaft per ISO R775 with M42
x 3-6H Threaded Shaft End,
16W x 10H x 32L [.630W x
.394H x 1.26L] Key
16 – 53,98 [2.125] Dia. Flat
DP 30 Deg. Involute Spline
with M12 x 1.75-6H Thread
in End, 55,9 [2.20] Min Full
Spline
11 , 12 Port Description
AA – 1,3125-12 UN-2B SAE
O-Ring Ports–Staggered
Ports
AB – SAE 19.05 [.750]
Dia. 4-Bolt Split Flange Staggered Ports
AC – G 1 Staggered Ports
AG – .750-16 UNF-2B SAE
13 , 14 Case Flow
02 – .4375-20 UNF-2B SAE
O-Ring Port With Check
Valve
03 – G 1/4 BSP Straight
Thread Port with Check
Valve
06 –.5625-18 UNF-2B SAE
O-Ring Port with Shuttle Valve
10 – .750-16 UNF-2B SAE
O-ring Ports, External
Lubrication Circuit Requires
Case Drain must be
Connected, .063 Shuttle Flow
Orifice
0 – None
A – Set at 4.5 [65 lbf/in2]
B – Set at 15.2 [220 lbf/in2]
16 , 17 Pressure/Flow Option
00 – None
20 , 21 Accessories
00 – None
(Hardware)
00 – None
01 – Non-Masked
Nameplate
02 – Non-Masked Nameplate,
Low Noise Valve Plate
03 – Low Noise Valve Plate
(Assembly)
00 – None
AA – Reverse Rotation
Box
Primer
AD – No Paint, Bulk Box
Option
AE – Low Gloss Black
Primer, Bulk Box
Option
28 , 29 Customer ID
00 – None
30 Design Code
F – Sixth
18 Geroler Option
0 – Standard
2 – Tight Fitting
19 Seal Option
0 – Standard
1 – Viton
3 – Seal Guard
Feature in bold are preferred
and allow for shorter lead time
10,000 Series
Features
Highlights
• Many options like 2 speed
and speed sensors make
this motor “smart”
• High torque and flow
• Low pressure loss even in
higher flows
Benefits
• High power density for
demanding mobile and
industrial applications
• Many options to draw
from
Applications
• Boring
• Industrial
• Metal Forming
• Port Equipment
• Saw Mill
Description
This is the biggest disc valve motor of our line with
up to 45 GPM and 24,000 in-lb of torque in continuous
mode, this motor is powerful and yet provides good
efficiency.
Specifications
Geroler Element
Flow l/min [GPM]
Speed RPM
Pressure bar [PSI]
Torque Nm [lb-in]
4 Displacements
501 Cont.**
784 Inter.*
200 [3000] Cont.**
270 [4000] Inter.*
2700 [23910] Cont.**
3440 [30460] Inter.*
** Continuous— (Cont.) Continuous rating, motor may be run continuously at these ratings.
C-6
Boring
Metal Forming
Port Equipment
C-6-1
10,000 Series
Specifications
10,000 Series Motors
345 [21.0]
480 [29.3]
665 [40.6]
940 [57.4]
Max. Speed (RPM) @ Flow
Flow
l/min [GPM]
Continuous
Intermittent
Continuous
Intermittent
501
784
170 [45]
265 [70]
354
552
170 [45]
265 [70]
254
396
170 [45]
265 [70]
179
279
170 [45]
265 [70]
Torque*
Nm [lb-in]
Pressure
∆ bar
[∆ PSI]
Weight
kg [lb]
Continuous
Intermittent
Continuous
Intermittent
Peak
Standard or
Wheel Mount
Bearingless
1040 [ 9220]
1390 [12310]
205 [3000]
275 [4000]
275 [4000]
43,5 [96.0]
1475 [13050]
1965 [17410]
205 [3000]
275 [4000]
275 [4000]
45,4 [100.0]
2085 [18450]
2610 [23080]
205 [3000]
260 [3750]
275 [4000]
46,3 [100.0]
2700 [23910]
3440 [30460]
190 [2750]
240 [3500]
260 [3750]
47,2 [104.0]
31,3 [69.0]
33,1 [73.0]
33,1 [73.0]
34,9 [77.0]
Note:
load applications.
275 bar [4000 PSI]
∆ bar [∆ PSI] :
outlet port
Continuous Rating:
Maximum Case Pressure:
20 bar [300 PSI]
C-6-2
10% of every minute
Peak Operation:
1% of every minute
Recommended Fluids:
Recommended System
Operating Temp.:
-34°C to 82°C [-30°F to
180°F]
4406: 20/18/13
10,000 Series
345 cm3/r [21.0 in3/r]
Performance Data
[1]
in production.
3,8
[2]
Flow LPM [GPM]
7,5
[4]
15
[8]
30
[ 12 ]
45
[ 16 ]
61
[20]
76
[24]
91
[28]
Continuous
Peak
Intermittent
No Operation
10 6
[32]
121
[36]
136
[40]
151
480
[250]
15
[1]
3,8
[2]
Flow LPM [GPM]
7,5
[4]
15
[8]
30
[ 12 ]
45
[ 16 ]
61
[20]
76
[24]
91
[28]
10 6
[32]
121
[36]
136
[40]
151
[45]
17 0
[60]
227
[70]
265
[500 ] [1000 ]
35
70
[3120]
355
4
[4320]
490
11
[4310]
485
27
[4290]
485
58
[4270]
480
90
[4240]
480
122
[4200]
475
154
[4170]
470
18 5
[4130]
465
217
[4080]
460
249
[4040]
455
280
[3990]
450
312
cm3/r
[1500]
10 5
[4640]
525
2
[6500]
735
8
[6490]
735
24
[6480]
730
55
[6450]
730
87
[6420]
725
119
[6390]
720
150
[6350]
715
182
[6310]
715
214
[6270]
7 10
245
[6220]
705
277
[6170]
695
308
[29.3
[2000]
140
[760]
85
6
[1040]
12 0
15
[1040]
12 0
31
[1020]
115
62
[990]
110
94
[960]
110
125
[930]
10 5
157
[890]
10 0
18 9
[850]
95
221
[810]
90
252
[760]
85
282
[710]
80
3 18
[1540]
17 5
5
[2140]
240
13
[2130]
240
29
[2110]
240
61
[2080]
235
93
[2060]
235
124
[2020]
230
156
[1980]
225
18 8
[1940]
220
220
[1900]
215
251
[1850]
210
281
[1800]
205
316
[647]
75
354
[430]
50
474
[1740] [3920] [6110] [8290]
445
690
935
19 5
351
348
344
353
[1520] [3710] [5890] [8070]
420
665
910
170
471
467
462
473
[1360] [3540] [5730] [7910]
400
645
895
15 5
550
546
541
552
[45]
in3/r]
[2500]
170
17 0
[60]
[3000]
205
[3500]
240
[4000]
275
[250]
15
[50 0 ]
35
[600]
70
3
[ 740]
85
21
[730]
80
43
[720]
80
87
[700]
80
131
[680]
75
176
[660]
75
221
[630]
70
266
[6 0 0 ]
70
3 10
[570]
65
356
[540]
60
4 00
[500]
55
445
[1310 ]
15 0
1
[1510]
170
19
[1500]
170
41
[1490]
170
86
[1470]
165
130
[1450]
16 5
17 5
[1430]
160
220
[1400]
160
265
[1370]
155
309
[1340]
150
355
[1310 ]
150
399
[1270]
145
444
[460]
50
501
[1220] [2760] [4300] [5840] [7380]
310
485
660
835
140
498
492
486
480
500
[1080] [2620] [4160] [5710] [7250]
295
470
645
820
130
665
658
651
644
668
[960] [2510] [4050] [5590] [7140]
110
285
460
630
805
784
777
769
761
754
227
[70]
265
[8690]
980
5
[8680]
980
21
[8660]
980
53
[8630]
975
84
[8600]
970
11 6
[8570]
970
147
[8530]
965
179
[8490]
960
210
[8450]
955
242
[8400]
950
273
[8350]
945
305
[10870]
1230
2
[10860] [13050]
1225
1475
18
16
[10840] [13030]
1225
1470
50
47
[10820] [13000]
1220
1470
81
78
[10790] [12970]
1220
1465
113
110
[10750] [12940]
1215
1460
144
141
[10720] [12900]
1210
1460
175
172
[10680] [12860]
1205
1455
207
203
[10630] [12820]
12 00
1450
238
235
[10590] [12770]
119 5
1445
270
266
[10540] [12720]
119 0
1440
3 01
297
[10470]
118 5
340
[10260]
1160
458
[10100]
1140
536
[15230] [17410]
1965
1720
10
13
[15210] [17390]
1965
1720
42
44
[15180] [17370]
1965
1715
73
75
[15150] [17340]
1960
1710
104
107
[15120] [17300]
1955
1710
135
138
[15080]
1705
169
[15040]
1700
200
[15 000]
1695
231
[2510]
285
777
}
[1000 ] [15 0 0 ] [2000] [2500]
70
10 5
14 0
170
[3050]
345
15
[3040]
345
37
[3030]
340
82
[3020]
340
127
[3000]
340
172
[2970]
335
217
[2950]
335
261
[2920]
330
306
[2890]
325
351
[2850]
320
396
[2820]
320
441
[4600]
520
11
[4590]
520
33
[4580]
515
78
[4560]
515
123
[4540]
515
167
[4520]
5 10
212
[4490]
505
256
[4460]
505
3 01
[4430]
500
346
[4400]
495
390
[4360]
495
435
[6140]
695
8
[6140]
695
30
[6120]
690
74
[610 0]
690
118
[6080]
685
163
[6060]
685
207
[6030]
680
252
[6000]
680
296
[5970]
675
340
[5940]
670
384
[5910]
670
429
[7680]
865
4
[7680]
870
26
[7670]
865
70
[7650]
865
11 4
[7630]
860
158
[7600]
860
202
[7580]
855
246
[7550]
855
291
[7520]
850
335
[7480]
845
379
[7450]
840
423
[3000]
205
[3500]
240
[4000]
275
[9220] [10770] [12310 ]
139 0
1040
1215
14
22
18
[9210] [10750] [12300]
1040
1390
1215
66
58
62
[9190] [10740] [12280]
1040
1385
1215
110
10 2
10 6
[9170] [10720] [12260]
1035
1385
1210
154
145
149
[9150] [10690] [12230]
1035
1380
1210
19 8
18 9
193
[9120] [10660] [12210]
1380
1030
1205
232
242
237
[9090] [10640] [12180]
1025
1200
1375
286
280
275
[9060] [10610] [12150]
1025
1200
1370
329
324
319
[9030] [10570] [12120]
1020
1370
119 5
373
362
368
[8990] [10540]
1015
1190
417
412
[8910] [10450]
1005
1180
473
467
[8800]
995
637
[8680]
980
746
Torque [lb-in]
Nm
Speed RPM
C-6
[12660]
1430
336
[12440]
1405
454
[12280]
1385
532
C-6-3
10,000 Series
10,000
Series Series
10,000
Performance
Data
Performance
Performance Data
Data
665 cm3/r [40.6 in3/r]
Pressure Bar [PSI]
[250]
15
Flow LPM [GPM]
Peak Peak
No Operation
Intermittent
Intermittent
No Operation
No Operation
940 cm3/r [57.4 in3/r]
Pressure Bar [PSI]
[1]
3, 8
[2 ]
Flow LPM [GPM]
Flow LPM [GPM]
7,5
[4]
15
[8 ]
30
[12 ]
45
[16]
61
[20]
76
[24]
91
[28]
10 6
[32]
121
[36 ]
136
[40]
151
[45]
170
[60]
227
[70]
265
C-6-4
[1]
[250]
15
3, 8
[2 ]
[2080]
235
7,5 3
[4]
[2090]
235
15 7
[2080]
[8 ]
235
15
30
[12 ]
[2040]
230
4531
[16]
[1990]
225
61
47
[20]
[1930]
220
7663
[24]
[1860]
210
91
79
[28]
[1780]
200
10 695
[32]
[1700]
190
121
111
[36 ]
[1620]
185
136
127
[40]
[1520]
170
151
143
[1420]
[45]
160
159
170
[60]
[1290]
145
227
179
[70]
[860]
95
265
239
[540]
60
279
cm[1000]
/r [57.4[1250]
in /r][1500]
[500]940
[750]
Bar [PSI]
35 Pressure
50
70
85
105
3
[2080] [4260]
[6440] [1250]
[500]
[750] [1000]
235
480 730
35
50
70
85
3
2
1
[2090] [6440]
[4270] [6450] [8640]
[4260]
235 730
480
730
975
480
5
5
27
16
[2080]
[4260]
[6440]
[8620]
[4270] [6450] [8640] [10820]
235 730
480 975
730 122
9750
480
15
14
13
134
6
5
5
[2040] [6440]
[4220] [8620]
[6400] [10810]
[8590]
[4260]
230 730
475 975
725 1220
970
480
30
29
28
1431
13
13
12
[1990] [6400]
[4170] [8590]
[6350] [10770]
[8540]
[4220]
225 725
470 970
715 1215
965
475
47
46
44
30
29
2845
28
[1930] [6350]
[4110] [8540]
[6290] [10720]
[8480]
[4170]
220 715
465 965
710 1210
960
470
62
61
60
4663
45
44
43
[1860] [6290]
[4040] [8480]
[6220] [10660]
[8410]
[4110]
210 710
455 960
705 1205
950
465
79
78
77
76
62
61
60
59
[1780] [6220]
[3970] [8410]
[6150] [10590]
[8330]
[4040]
200 705
450 950
695 1195
940
455
94
93
92
7895
77
76
75
[1700] [6150]
[3890] [8330]
[6070] [10520]
[8250]
[3970]
190 695
440 940
685 1190
930
450
111 110
109
108
94
93
92
91
[1620] [6070]
[3800] [8250]
[5980] [10440]
[8160]
[3890]
185 685
430 930
675 1180
920
440
127 109
126 108
125
124
110
107
[1520] [5980]
[3710] [8160]
[5890] [10350]
[8070]
[3800]
170 675
420 920
665 1170
910
430
143 125
142 124
141 140
126
123
[1420] [5890]
[3610] [8070]
[5790] [10260]
[7970]
[3710]
160 665
410 910
655 1160
900
420
159 141
158 140
157
156
142
139
[3610]
[1290] [5790]
[3480] [7970]
[5660] [10160]
[7840]
410
145 655
395 900
640 1150
885
158
155
179 157
178 156
177
176
[860] [5660]
[3040] [7840]
[5230] [10020]
[7410]
[3480]
95 640
345 885
590 11
835
395
30
239 177
238 176
236 235
178
174
[540] [5230]
[2720] [7410]
[4910] [9600]
[7090]
[3040]
60 590
305 835
555 1085
800
345
279 236
278 235
276
275
238
234
[2720] [4910] [7090] [9270]
305
555
800
1045
278
276
275
274
3
Flow LPM [GPM]
[1750]
120
Peak
Continuous
Continuous
Intermittent
[250]
15
35 Pressure
50
70Bar [PSI]
85
105
[6100] [1500]
[7630] [1750]
[1470]
[4550] [1250]
[500] [3010]
[750] [1000]
690
860
165
340
515
35
50
70
85
105
120
2
1
4
3
3
[1480] [4550]
[3020] [6100]
[4560] [7630]
[6110] [7650] [9200]
[3010]
[1]
340 690
515 860
690
165 515
865 1040
340
10
7
6
28
17
3
39
3,8
[9190]
[1470 ] [4560]
[3010] [6110]
[4550] [7650]
[6100] [9200]
[7640] [10740]
[3020]
[2]
865 1040
165 515
340 690
515 865
690 1040
1215
340
22
21
20
19
18
175
9
8
7
7
6
7,5
[1440] [4550]
[2980] [6100]
[4530] [7640]
[6070] [9190]
[7610] [10730]
[9160]
[3010]
[4]
86 0 1035
165 515
335 690
510 865
685 1040
340
1210
44
43
41
40
39
21
20
1942
18
17
15
16
[1400] [4530]
[2950] [6070]
[4490] [7610]
[6040] [9160]
[7580] [10700]
[9120]
[2980]
[8]
160 510
335 685
505 86
680
855 1030
335
0 1035
1210
67
66
65
64
63
62
43
42
41
40
39
38
30
[1360] [4490]
[2910] [6040]
[4450] [7580]
[5990] [9120]
[7540] [10670]
[2950]
[12]
[9080]
155 505
330 680
505 855
675 1030
850 1025
335
1205
87
86
85
84
6689
6588
64
63
62
61
45
[1310] [4450]
[2860] [5990]
[4400] [7540]
[5940] [9080]
[9030]
[7490] [10620]
[2910]
[16]
150 505
375 675
495 850
670 1025
845 1020
330
1200
112
111 110
109
108
107
88
87
86
85
84
83
61
[1260] [4400]
[5890] [9030]
[7440] [10580]
[8980]
[2800] [5940]
[4350] [7490]
[2860]
[20]
140 495
665 1020
840 1015
315 670
490 845
375
1195
135 110
132 108
131 107
130
129
134 109
111
106
76
[2750] [5890]
[4290] [7440]
[5840] [8980]
[7380] [10520]
[8920]
[1200] [4350]
[24]
[2800]
310
485 840
660 1015
835 1010
135 49
0
665
1190
315
156 131
155 130
154 129
153
151
157 132
91
128
134
[2690] [5840]
[4230] [7380]
[5770] [8920]
[7320] [10470]
[8860]
[1140] [4290]
[28]
[2750]
305 660
480 835
650 1010
825 1000
130 485
310
1185
179 154
177 153
176 151
175
174
180 155
106
156
150
[2620] [5770]
[4160] [7320]
[5710] [8860]
[8800]
[1080] [4230]
[7250] [10400]
[32]
[2690]
295 650
470 825
645 1000
820 1175
995
120 480
305
201 176
200 175
199 174
19 8 19
6
202 177
12 1
179
173
[2550] [5710]
[4100] [7250]
[5640] [8800]
[7180] [10340]
[8730 ]
[1010] [4160]
[36 ]
[2620]
290 645
465 820
635 995
810 1170
985
115 470
295
224 199
222 19221
2195
225 200
136
201
8 19220
6
19
[40]
[2550]
[920] [4100]
[2460] [5640]
[4000] [7180]
[5550] [8730
[7090]] [10270]
[8630]
290
105 465
280 635
450 810
625 985
800 1160
975
151
224
217
254 222
252 221
251 220
249 219
248
247
[610] [4000]
[2150] [5550]
[3700] [7090]
[5240] [8630]
[6780] [10180]
[8330]
[2460]
[45]
245 625
420 800
590 975
765 1150
940
28070 450
338 251
336 249
335 248
334 247
332
331
252
170
245
[3470] [6780]
[5010] [8330]
[6560] [8100]
[1930] [5240]
[380] [3700]
[2150]
[60]
[9870]
390 765
565 940
740 1115
915
220 590
45 420
245
391 332
390 331
388 387
393 334
396 335
336
227
329
[70]
[1930] [3470] [5010] [6560] [8100] [9640]
565 740
915
220 390
1090
265
391
390
388 387
393
385
[3470] Torque [lb-in]
Nm
390
391 Speed RPM
[3470] Torque [lb-in]
Nm
390
RPM [3000] [3250] [3500]
[2500]Speed
[2750]
[2000] [2250] 391
170
190
205
225
240
155
140
Motors
run with high
designated
with a number
efficiency
in all areas
for torque
and speed. For
designated
with alife
number
best motor
select a
for torque
speed.
motor and
to run
with For
a torque
best motor
life select
and speed
rangeashown in
motorthetolight
runshaded
with aarea.
torque
and speed
range
shown
in
Performance
data is typical
the light
shaded
area.Actual
at 120
SUS.
data may
Performance
typical
vary slightlydata
fromisunit
to unit
at 120in production.
SUS. Actual data may
in production.
in production.
Continuous
3/r [40.6 in3/r]
cm[1000]
[500] 665
[750]
[1250] [1500]
[1]
[250]
15
3,8
[2]
[1470]
165
7,5 4
[4]
[1480]
165
15
10
[8] ]
[1470
165
3022
[12]
[1440]
165
4544
[16]
[1400]
160
61
67
[20]
[1360]
155
7689
[24]
[1310]
150
91
112
[28]
[1260]
140
106
135
[32]
[1200]
135
12
1
157
[36 ]
[1140]
130
136
180
[40]
[1080]
120
151
202
[1010]
[45]
115
225
170
[60]
[920]
105
227
254
[70]
[610]
70
265
338
[380]
45
396
}
}
[1500]
105
[1750]
120
[2000]
140
[2250]
155
[10820]
122 0
4
[10810]
[13000]
1220
1470
123
[10770]
[12990]
1215
1470
28
11
[10720]
[12950]
1210
1465
43
27
[10660]
[12900]
1205
1460
59
43
[10590]
[12840]
1195
1450
75
58
[10520]
[1277 0]
1190
1445
91
74
[10440]
[12700]
1180
1435
107
90
[10350]
[12620]
1170
1425
123
106
[10260]
[12530]
1160
1415
139
122
[10160]
[12440]
1150
1405
155
138
[12340]
[10020]
1395
11 30
154
174
[9600]
[12210]
1085
1380
234
174
[9270]
[11780]
1045
1330
274
233
[11460]
1295
273
[13000]
1470
3
[12990]
[15190]
1470
1715
11
2
[12950]
[15170]
1465
1715
27
10
[12900]
[15140]
1460
1710
43
26
[12840]
[15090]
1450
1705
58
42
[1277
0]
[15030]
1445
1700
74
58
[12700]
[14960]
1435
1690
90
73
[12620]
[14880]
1425
1680
106
89
[12530]
[14800]
1415
1675
122
105
[12440]
[14720]
1405
1665
138
121
[12340]
[14620]
1395
1650
154
137
[14520]
[12210]
1640
1380
153
174
[11780]
[14400]
1330
1625
233
173
[11460]
1295
273
[15190]
1715
2
[15170]
[17370]
1715
1965
101
[15140]
[17360]
1710
1960
269
[15090]
[17320]
1705
19
55
42
25
[15030]
[17270]
1700
1950
58
41
[14960]
[17210]
1690
1945
73
57
[14880]
[17140]
1680
193 5
89
72
[14800]
[7070]
1675
1930
105
88
[14720]
[16990]
1665
1920
121
104
[14620]
1650
137
[14520]
1640
153
[17370]
1965
1
[17360]
1960
9
[17320]
[19540]
19
55
2210
258
[17270]
[19500]
1950
2200
41
24
[17210]
[19450]
1945
2200
57
40
[17140]
[19390]
193
5
2190
72
56
[7070]
[19320]
1930
2185
88
72
[16990]
1920
104
[2500]
170
[2750]
190
[3000]
205
[3250]
225
[3500]
240
[19540] [21720] [23910] [260 90] [28270] [30460]
2455 2700
2950 3195
3440
2210
7
7
6
5
4
8
[21720]
[19500] [21690]
[23910] [23870]
[260 90] [28270] [30460]
2450
2695
2200
2455 2700
2950 3195
3440
23
226
247
7
5
4
[19450]
[21690] [21640]
[23870]
2200
2450 2445
2695
39
40
23
22
[19390]
[21640]
2190
2445
56
39
[19320]
2185
72
[14400]
1625
173
[1750]
120
[2000]
140
[2250]
155
[2500]
170
[2750]
190
[3000]
205
[3250]
225
[3500]
240
[2000]
140
[2250]
155
[2500]
170
[2750]
190
[3000]
205
[3250]
225
[3500]
240
[3750]
260
[10740]
1215
5
[10730]
[12280]
12105
138
164
[10700]
[12270]
1210
1385
38
15
[10670]
[12250]
1205
1385
61
37
[10620]
[12210]
1200
1380
83
60
[10580]
[12170]
1195
1375
106
82
[10520]
[12120]
1190
1370
128
104
[10470]
[12070]
1185
1365
150
127
[10400]
[12010]
1175
1355
173
149
[10340]
[11950]
1170
1350
19
5
172
[10270]
[11880]
1160
1340
217
194
[11810]
[10180]
1335
1150
216
245
[9870]
[11720]
1115
1325
329
244
[9640]
[11420]
1090
1290
385
328
[11190]
1265
384
[12280]
138 5
4
[12270]
[13830]
1385
1565
153
[12250]
[13820]
1385
1560
37
14
[12210]
[13790]
1380
1560
60
36
[12170]
[13750]
1375
1555
82
59
[12120]
[13710]
1370
1550
104
81
[12070]
[13660]
1365
1545
127
103
[12010]
[13610]
1355
1540
149
126
[11950]
[13550]
1350
1530
172
148
[11880]
[13490]
1340
1525
194
170
[11810]
[13430]
1335
1515
216
193
[13360]
[11720]
1510
1325
215
244
[11420]
[13260]
1290
1500
328
243
[11190]
[12960]
1265
1465
384
327
[13830]
1565
3
[13820]
[15370]
1560
1735
142
[13790]
[15360]
1560
1735
36
13
[13750]
[15330]
1555
1730
59
35
[13710]
[15300]
1550
1730
81
58
[13660]
[15260]
1545
1725
103
80
[13610]
[15210]
1540
1720
126
102
[13550]
[15150]
1530
1710
148
124
[13490]
[15100]
1525
1705
170
147
[13430]
[15040]
1515
1700
193
169
[13360]
[14970]
1510
1690
215
191
[14900]
[13260]
1685
1500
214
243
[12960]
[14810]
1465
1675
327
242
[15370]
1735
2
[15360]
[16910]
1735
1910
131
[15330]
[16900]
1730
1910
35
12
[15300]
[16880]
1730
1905
58
34
[15260]
[16840]
1725
1905
80
57
[15210]
[16800]
1720
1900
102
79
[15150]
[16750]
1710
1890
124
101
[15100]
[16700]
1705
1885
147
123
[15040]
[16640]
17000
188
169
146
[14970]
[16580]
1690
1875
191
168
[14900]
[16510]
1685
1865
214
190
[16440]
[14810]
1855
1675
212
242
[16910]
1910
1
[16900]
1910
12
[16880]
[18450]
1905
2085
34
11
[16840]
[18420]
1905
2080
57
33
[16800]
[18380]
1900
2075
79
56
[16750]
[18340]
1890
2070
101
78
[16700]
[18300]
1885
2070
123
100
[16640]
[18240]
188
0
2060
146
122
[16580]
1875
168
[16510]
1865
190
[16440]
1855
212
[18450]
2085
11
[18420]
[19990]
2080
2260
33
10
[18380]
[19960]
2075
2255
56
32
[18340]
[19930]
2070
2255
78
55
[18300]
[19890]
2070
2245
100
77
[18240]
[19840]
2060
2240
122
99
[19990]
2260
10
[19960]
[21540]
2255
2435
329
[19930]
[21510]
2255
2430
55
32
[19890]
[21470]
2245
2425
77
54
[19840]
[21400]
2240
2420
99
76
[3750]
260
[21540] [23080]
2435 2610
8
9
[21510]
[23080] [23050]
2430
2605
2610
328
31
[21470]
[23050] [23020]
2425
2605 2600
54
53
31
[21
400]
[23020]
2420
2600
76
53
10,000 Series
Ports
Dimensions
Standard Mount
Y Max.
Port B
X
7/8-14 UNF
O-ring PortAlternative Case Drain (2)
9/16 - 18 UNF
O-ring Case
Drain Port
14,5/13,2
[.57/.52]
22,4/20,8
[.88/.82]
127,00/126,87
[5.000/4.995] Dia.
7/8-14 UNF
O-ring Case Drain
Port (2)
67,4/66,2
[2.65/2.61]
17,02/16,51
[.670/.650]
Dia. (4)
150,1 [5.91] Max
147,1
[5.79]
Max.
114,3 [4.50]
Square
C-6
Displacement
cm3/r [in3/r]
X
mm [inch]
Y
mm [inch]
345 [21.0]
480 [29.2]
665 [40.6]
940 [57.4]
282,4 [11.12]
295,1 [11.62]
295,1 [11.62]
313,4 [12.34]
380,7 [14.99]
393,4 [15.49]
393,4 [15.49]
411,7 [16.21]
C-6-5
10,000 Series
Ports
Dimensions
Wheel Mount
Y Max.
X
Port B
9/16 - 18 UNC
O-ring Case
Drain Port
131,1/127,8
[5.16/5.03]
21,1/20,0
[.83/.79]
184,9 [7.28]
Square Max.
127,0
[5.00]
177,80/177,67
Dia. 139,7 [7.000/6.995]
[5.50] Dia. (2)
Dia.
209,55 [8.250]
Dia. Bolt Circle
5,9/4,8
[.23/.19]
17,02/16,51
[.670/.650] Dia. (4)
Displacement
cm3/r [in3/r]
X
mm [inch]
Y
mm [inch]
345 [21.0]
480 [29.2]
665 [40.6]
940 [57.4]
166,9 [6.57]
179,6 [7.07]
179,6 [7.07]
197,8 [7.79]
265,9 [10.47]
278,6 [10.97]
278,6 [10.97]
297,2 [11.70]
C-6-6
10,000 Series
Ports
Dimensions
Bearingless
Bearingless
Port B
Y Max.
X
20,88/20,52
[.822/.808]
Dia. Thru (4)
200,5
[7.89]
Square
Max.
161,64
[6.364]
Square
9/16 - 18 UNF
O-ring Case
Drain Port
228,60
[9.000]
Dia. Bolt Circle
19,1/16,5
[.75/.65]
152,40/152,27
[6.000/5.995]
Dia.
12,7/12,4
[.50/.49]
Displacement
cm3/r [in3/r]
X
mm [inch]
Y
mm [inch]
345 [21.0]
480 [29.2]
665 [40.6]
940 [57.4]
158,0 [6.22]
170,7 [6.72]
170,7 [6.72]
189,0 [7.44]
256.3 [10.09]
269,0 [10.59]
269,0 [10.59]
287,5 [11.32]
Dimension D mm [inch]
Eaton Part No.
13280-001
133,6/128,5
[5.26/5.06]
13280-002
156,0/150,9
[6.14/5.94]
For 10,000 bearingless motor
application information,
contact your Eaton representative (mating coupling
blanks available from Eaton
Hydraulics).
C-6
D
Note:
C-6-7
10,000 Series
Bearingless
-B-
Coupling Depth
89,2 0.8
[3.51 .03]
51,1 1,8
[2.01 .07]
-B-
HRc with case depth (to 50HRc) of 0,076 1,02 [.030 - .040] (dimensions apply after
heat treat).
Coupling Depth
89,2 0.8
[3.51 .03]
51,1 1,8
[2.01 .07]
Case Flow
-ACase Flow
43,56
[1.715] Min.
43,56
[1.715] Min.
Circular
Finish
Finish
Major
Fillet R.
Finish
Pitch
Circular Tip R .
Minor
Major
Finish
Tip R .
Minor
C-6-8
Form
Fillet R.
Pitch
Form
Case Flow
-A-
Case Flow
Spline Pitch.................................................................................................. 10/20
Pressure Angle................................................................................................30°
Number of teeth............................................................................................... 16
Class of Fit................................................................................................... Ref. 5
Type of Fit...................................................................................................... Side
| 0,25 [.010] | D
Pitch Diameter ...................Ref. 40,640000 [1.6000000]
Major Diameter.....................................43,56 [1.715] Max. 43,18 [1.700] Min.
Fillet Radius.................................................................... 0,64 - 0,76 [.025 - .030]
Tip Radius....................................................................... 0,25 - 0,51 [.010 - .020]
Finish..........................................................................................................1,6 (63)
Lead Variation.................................................................................0,013 [.0005]
Maximum Actual......................................................................4,105 [.1616]
Dimension Between Two Pins........... Ref. 26,929 - 27,084 [1.0602 - 1.0663]
Pin Diameter.......................................... Ref. 34,272 - 34,450 [1.3493 - 1.3563]
.
10,000 Series
Dimensions
Shafts
2 1/4 Inch Tapered
2 1/4 Inch Straight
114,0/112,3
114,0/112,3[4.49/4.42]
[4.49/4.42]
End
EndofofShaft
ShafttotoMounting
MountingSurface
Surface(Std)
(Std)
2712
2712[24000]
[24000]
Max.
Max.Torque
Torque 57.150/57,137
57.150/57,137114,0/112,3 [4.49/4.42]
Nm
[2.2500/2.2495]
Nm[lb-in]
[lb-in]
End of Shaft[4.49/4.42]
114,0/112,3
[2.2500/2.2495]
Dia.
63,5
2712 [24000]
Dia.
63,5[2.50]
[2.50]
End
of
Shaft
to
Mounting
Surface (Std)
12,73/12,70
12,73/12,70
Max.
Torque
2712
[24000]
57.150/57,137
[.501/.500]
[.501/.500]
Nm [lb-in]
Max.
Torque 57.150/57,137
[2.2500/2.2495]
Sq.
Sq.Key
Key
Dia.
63,5 [2.50]
Nm [lb-in]
[2.2500/2.2495]
12,73/12,70
Dia.
63,5 [2.50]
[.501/.500]
12,73/12,70
Sq. Key
[.501/.500]
Sq. Key1/2-20
62,92/62,66
1/2-20UNF
UNF 62,92/62,66
xx23,8
[2.477/2.467]
23,8[.94]
[.94] [2.477/2.467]
Deep
Deep
97,5
97,5[3.84]
[3.84]
1/2-20 UNF 62,92/62,66
Max.
Max.Coupling
Coupling
[2.477/2.467]
x 23,8 UNF
[.94] 62,92/62,66
1/2-20
Deep
[2.477/2.467]
x 23,8 [.94]
97,5 [3.84]
Deep
Max.[3.84]
Coupling
97,5
Max. Coupling
2712
2712[24000]
[24000]
Max. Torque
End
EndofofShaft
ShafttotoMounting
MountingSurface
Surface(Std)
(Std)
Nm
Nm[lb-in]
[lb-in]
75,0
[2.95]
75,0 [2.95]
2712 [24000]
91,7/89,9 [3.61/3.54]
Max.
Involute
Max.Coupling
Coupling
Involute
Spline
Max.
TorqueSpline
2712
[24000]
End of Shaft
to Mounting
Surface (Std)
91,7/89,9
[3.61/3.54]
Flat
Root
Major
Dia.
Fit
52,1
Flat
Root
Major
Dia.
Fit
Nm8/16
[lb-in]
52,1[2.05]
[2.05] (Std)
Max.
Torque 16 Toot h
End of Shaft to Mounting
Surface
8/16Pitch
Pitch 16 Toot h
Min.
75,0 [2.95]
Min.Full
FullSpline
Spline
Nm [lb-in]
per
B92.1,
perANSI
ANSI
B92.1,1976
1976
Max.[2.95]
Coupling
Involute
Spline
75,0
Flat RootSpline
Major Dia. Fit
Max.52,1
Coupling
[2.05]
Involute
8/16Root
Pitch
16 Toot
Flat
Major
Dia.hFit
Min.[2.05]
Full Spline
52,1
per ANSI
1976
8/16
Pitch B92.1,
16 Toot
h
Min. Full Spline
per ANSI B92.1, 1976
1/2-20
53,972
1/2-20UNF
UNF
53,972
57,15
xx23,8
[2.1249]
57,15
23,8[.94]
[.94]
[2.1249]
[2.250]
Deep
Major
[2.250]
Deep
MajorDia.
Dia. Dia.
Dia.
1/2-20 UNF
53,972
57,15
x
23,8
[.94]
[2.1249]
1/2-20 UNF
53,972
[2.250]
Major Dia.
57,15
xDeep
23,8 [.94]
[2.1249]
Dia.
[2.250]
Deep
Major Dia.
Dia.
91,7/89,9
91,7/89,9[3.61/3.54]
[3.61/3.54]
1/8 Torque
2Max.
Inch 16 Tooth Splined
2712
222,5/219,7
2712[24000]
[24000]
222,5/219,7[8.76/8.65]
[8.76/8.65]
Max.
End
Max.Torque
Torque
EndofofShaft
ShafttotoMounting
MountingSurface
Surface(Whl)
(Whl)
Nm
Nm[lb-in]
[lb-in]
2712 [24000]
50,8
222,5/219,7 [8.76/8.65]
50,8[2.00]
[2.00]
Max.
Torque
2712
[24000]
End
of
Shaft
to
Mounting
Surface (Whl)
57,15
222,5/219,7
[8.76/8.65]
57,15
Nm[2.250]
[lb-in]
Max.
TorqueDia.
[2.250]
Dia. End of Shaft to Mounting Surface (Whl)
Nm [lb-in]
50,8 [2.00]
4,32/3,81
4,32/3,81
50,8
[2.00]
57,15[.170/.150]
[.170/.150]
[2.250]
Dia.
Dia.
Thru
57,15
14,313/14,287
Dia.
Thru
14,313/14,287
[2.250] Dia.
[.5635/.5625]
[.5635/.5625]
4,32/3,81
Sq.
Sq.Key
Key
[.170/.150]
4,32/3,81
94,7
94,7
Dia.
Thru
[.170/.150]
14,313/14,287
[3.73]
1-1/2-18
UNEF
[3.73]
1-1/2-18
Dia.
Thru UNEF
[.5635/.5625]
14,313/14,287
Sq. Key
[.5635/.5625]
SAE
SAEJ501
J501Standard
StandardTapered
Tapered
Shaft
94,7 Shaft
Sq. Key
125,00
0,17
Meter
7,14/6,80
[3.73]
125,00 UNEF
0,17Taper
Taperper
per
Meter
7,14/6,80[.281/.268]
[.281/.268]
1-1/2-18
94,7
[1.500±.002
Taper per Foot]
[1.500±.002
Foot]
1-1/2-18
UNEF Taper per[3.73]
SAE J501 Standard Tapered Shaft
125,00
Taper per
MeterShaft
7,14/6,80 [.281/.268]
SAE
J5010,17
Standard
Tapered
[1.500±.002
Foot]
125,00
0,17 Taper per Meter
7,14/6,80 [.281/.268]
Hub
Hub
Recommended
Hub
RecommendedTorque:
Torque:
(1150
Hub
(1150Nm
Nm[850
[850lb-ft]
lb-ft]Dry)
Dry)
( ( 880
880Nm
Nm[650
[650lb-ft]
lb-ft]Lub)
Lub)
Plus
Torque
required
Recommended
Torque:
Plus Torque requiredtoto
align
the
slotted
with
(1150
Nm
[850
lb-ft]nut
Dry)
Recommended
Torque:
align
the
slotted
nut
with
the
Shaft
Crosshole.
( 880
Nm
[650
lb-ft]Dry)
Lub)
(1150
[850
lb-ft]
theNm
Shaft
Crosshole.
required
to
( Plus
880Torque
Nm [650
lb-ft] Lub)
76,2
alignTorque
the slotted
nutto
with
Plus
required
76,2[3.00]
[3.00]
the Shaft
Crosshole.
align
the slotted
nut with
76,2 [3.00]
76,2 [3.00]
60,0
60,0
[2.37]
[2.37]
Slotted Hexagon Nut
1-1/2-18
1-1/2-18UNEF
UNEF
1,52
1,52[.06]
[.06]xx45
45
Chamfer
Chamfer
1-1/2-18 UNEF
1,52 [.06]UNEF
x 45
1-1/2-18
Chamfer
30°
1,52
[.06] x 45 30°
Chamfer
30°
30°
60,0
[2.37]
60,0
[2.37]
10,9
10,9[.43]
[.43]
C-6
[.16]
10,94,1
[.43]
4,1
[.16]
10,9 [.43]
4,1 [.16]
4,1
[.16]
30°
30°
15,7 [.62]
30°15,7 [.62]
30°
15,7 [.62]
15,7 [.62]
C-6-9
10,000 Series
Side Shaft Load Capacity
radial load capacity on
the motor shaft at various
locations with an external
thrust load of 454 kg
[1000 lb]. The maximum
allowable thrust load is
908 kg [2000 lb]. Note:
push outward on the shaft
at 200 kg/7 Bar [441 lb/100
PSI].
Thrust Load
Max. Axial Loads
908 kg [2000 lb]
below.
RPM
50
100
200
300
400
500
600
700
800
1.23
1.00
0.81
0.72
0.66
0.62
0.58
0.56
0.54
kg
4500
[lb]
[10000]
4000
[ 9000]
3500
[ 8000]
[ 7000]
3000
[ 6000]
2500
[ 5000]
2000
[ 4000]
1500
[ 3000]
-120 -100 -80 -60 -40 -20
[-5]
[-4] [-3]
[-2]
[-1]
0
20 40 60 80 100 120
[1]
[2]
[3]
[4]
[5]
mm
[inch]
Mounting Surface
kg
4500
[lb]
[10000]
4000
[ 9000]
3500
[ 8000]
[ 7000]
3000
[ 6000]
2500
[ 5000]
2000
[ 4000]
1500
[ 3000]
-20
0
20 40 60 80 100 120 140 160 180 200 220 240
mm
[-1]
0
[1]
[inch]
[2]
[3]
[4]
Mounting Surface
C-6-10
0
[5]
[6]
[7]
[8]
[9]
10,000 Series
Dimensions
Ports
1 1/4 Inch Split Flange Ports (2)
7/16-14 UNC x
29,2 [1.15] Deep (8)
9/16-18 UNF O-ring
Case Drain Port
Port B
15,10
[.594] (2)
Port A
29,40
[1.156]
30,20
[1.188] (2)
45°
75,5/74.9
[2.97/2.95]
58,70 [2.312]
30,8/29,2
[1.21/1.15]
29,5/27,4
[1.16/1.08]
102,2/101,0
[4.02/3.98]
182,9 [7.20] Max.
1 5/16 -12 O-ring Ports (2)
9/16-18 UNF O-ring
Case Drain Port
Port B
Port A
76,2/74,1
[3.00/2.92]
45°
30,8/29,2 [1.21/1.15]
29,5/27,4
[1.16/1.08]
106,2 [4.18]
184,7 [7.27]
End View
Common Dimensions
154,0 [6.06] Max.
9/16-18 UNF O-ring
Case Drain Port
74,0/72,1
[2.91/2.84]
C-6
16,8/15,7 [.66/.62]
C-6-11
10,000 Series
Note:
For 10,000 Series Motors
with a configuration Not
Shown in the chart below:
Use model code number
system on the next page to
specify product in detail.
Product Numbers
Mounting
Shaft
Port Size
119-, 120-, or 121 - plus four
Example 121-1014.
345 [21.0]
480 [29.3]
665 [40.6]
940 [57.4]
1 5/16 O-ring
119-1028
-1029
-1030
-1031
1 1/4 inch Split Flange
119-1040
-1041
-1042
-1043
Standard
2 1/8 Inch
SAE
16
T Splined
C-Mount
1 5/16 O-ring
119-1032
-1033
-1034
-1035
119-1044
-1045
-1046
-1047
2 1/4 Inch
Tapered
1 5/16 O-ring
119-1036
-1037
-1038
-1039
119-1048
-1049
-1050
-1051
2 1/4 Inch Straight
1 5/16 O-ring
120-1005
-1006
-1007
-1008
120-1017
-1018
-1019
-1020
Wheel
2 1/8 Inch
16 T Splined
Motor
1 5/16 O-ring
120-1009
-1010
-1011
-1012
120-1021
-1022
-1023
-1024
2 1/4 Inch
Tapered
1 5/16 O-ring
120-1013
-1014
-1015
-1016
120-1025
-1026
-1027
-1028
1 5/16 O-ring
121-1007
-1008
-1009
-1010
121-1011
-1012
-1013
-1014
2 1/4 Inch Straight
Bearingless
121-1014
C-6-12
10,000 Series
identify all of the configuration options for the 10,000 Series
desired features. All 30-digits of the code must be present
when ordering. You may want to photocopy the matrix below
to ensure that each number is entered in the correct box.
Model Code
M
1 0
* * *
* *
* *
* *
* *
*
1
2 3
4 5 6
7 8
9 10
11 12
13 14
15
1 Product
M – Motor
2 , 3 Series
10 – 10,000 Series
cm3/r [in3/r]
210 – 343.8 [20.98]
293 – 479.5 [29.26]
406 – 665.3 [40.60]
574 – 940.8 [57.41]
Mounting
Description
AA – Standard, 4 Bolt:
127,0 [5.00] Pilot Dia. 16,76
[.660] Dia. Holes on 161,92
AB – Wheel, 4 Bolt: 16,76
[.660] Dia. Holes on 209,55
AC – Bearingless, 4 Bolt:
152,4 [6.00] Pilot Dia. 20,70
[.815] Holes on 228,60 [9.00]
Dia. Bolt Circle 7 , 8
Shaft
9 , 10 Output
Description
01 – 57,15 [2.250] Dia.
Straight with .500-20
UNF-2B Thread in End,
12.7 [.50] Square x 63,5
[2.50] Straight End
02 – 57,15 [2.250] Dia.
.125:1 Tapered Shaft Per
SAE J512 with 1.500-18
UNEF-2A Threaded Shaft
End and Slotted Hex Nut,
14,288 [.5625] Square x
50,8 [2.00] Straight Key
03 – 53,98 [2.125] Dia. Flat
Root, Major Dia. Fit, 16
Tooth, 8/16 DP, 30 Degree
Involute Spline with
.500-20 UNF-20 Thread
in End. 52,07 [2.050]
Minimum Full Spline
Length
11 , 12 Ports
AA – 1.3125 -12 UN O-Ring
Staggered Ports
AB – 31,75 [1.250] Dia.
4 Bolt Split Flange
Staggered Ports with
.4375-15 UNC-2B Tapped
Mounting Holes
0 0
*
*
16 17 18
19
* *
0 0
20 21 22 23
Flow Options
13 , 14 Case
01 – .5625-18 UNF-2B Case
Drain SAE O-Ring Port
0 – None
16 , 17 Pressure/Flow
Option
00 – None
18 Geroler Option
0 – Standard
1 - Free Running
* *
* *
0 0
*
24 25 26 27 28 29 30
26 , 27 Paint / Packaging
00 – None
Primer
28 , 29 Customer
Identification
00 – None
30 Design Code
C – Third (Standard and
Wheel Mounts)
D – Fourth (Bearingless
Mount)
19 Seal Option
0 – Standard
4 – Seal Guard
20 , 21 Accessories
00 – None
(Hardware)
00 – None
(Assembly)
00 – None
AA – Reverse Rotation
C-6
C-6-13
Notes
C-6-14

Eaton® Char-Lynn® Disc Valve Hydraulic Motors

Transcription

Similar documents

Corporate PPT November 2015