SPP-ID975/ID976

SPP-ID975/ID976
SERVICE MANUAL
US Model
SPP-ID975
Ver 1.0 1999. 11
Canadian Model
SPP-ID976
Photo: SPP-ID975
SPECIFICATIONS
General
Base phone
Frequency band (SPP-ID975)
902 – 928 MHz
Frequency band (SPP-ID976)
923.1 – 927.75 MHz
Base phone : 18 µW
Handset
: 73 µW
Operating channel
30 channels
Dial signal
Tone, 10 PPS (pulse) selectable
Supplied accessories
AC power adaptor AC-T122 (1)
Telephone line cords (2)
Wall bracket for base phone (1)
Rechargeable battery pack BP-T23 (1)
Power source
DC 9V from AC power adaptor
AC-T122
Battery charging time
Approx. 24 hours
Dimensions
Approx. 166 × 63 × 225 mm (w/h/d),
antenna excluded
(approx. 6 5/8 × 2 1/2 × 8 7/8 inches)
Antenna: Approx. 120 mm
(approx. 4 3/4 inches)
Mass
Approx. 595 g
(approx. 1 lb 9 oz), wall bracket excluded
Handset
Power source
Rechargeable battery pack BP-T23
Battery charging time
Approx. 12 hours
Battery life
Standby : Approx. 7 days
Talk
: Approx. 6 hours
Dimensions
Approx. 58 × 177 × 46 mm (w/h/d),
antenna excluded
(approx. 2 3/8 × 7 × 1 13/16 inches)
Antenna: Approx. 72 mm
(approx. 2 7/8 inches)
Mass
Approx. 270 g
(approx. 9.5 oz), battery included
Design and specifications are subject to
change without notice.
Notes on Chip Component Replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be damaged by heat.
CORDLESS TELEPHONE
MICROFILM
–1–
Note for Replacement of the ASIC Board
The ID is written in the ASIC board.
When replacing the ASIC board, the U3003 on BASE MAIN board
and U1001 on HAND MAIN board should be replaced together as
a pair.
Part No. : X-3378-159-1 ASIC ASSY (one assy of two parts)
TABLE OF CONTENTS
1. GENERAL
Read This First ........................................................................ 3
Checking the Package Contents .............................................. 3
Setting Up the Base Phone ...................................................... 3
Preparing the Battery Pack ...................................................... 4
Entering the Area Code ........................................................... 5
Identifying the Parts ................................................................ 5
Making Calls ........................................................................... 6
Receiving Calls ........................................................................ 7
Speed Dialing .......................................................................... 8
Phone Directory ....................................................................... 8
Setting the Ringer Type ......................................................... 10
Switching the Phones During a Call ...................................... 10
Talking Between the Phones (Intercom) ............................... 10
Transferring a Call ................................................................. 11
Understanding the Caller ID Service ..................................... 11
Looking at the Caller ID List ................................................ 11
Using the Caller ID List ........................................................ 12
Using “Caller ID with Call Waiting” Service ........................ 13
Using Visual Message Waiting Service ................................. 13
Mounting the Base Phone on a Wall ..................................... 14
– BASE MAIN BOARD (SIDE A) –
U3003
2. DISASSEMBLY
– HAND MAIN BOARD (SIDE B) –
U1001
2-1.
2-2.
2-3.
2-4.
2-5.
2-6.
Case (Rear) ........................................................................ 15
RF Unit (HS), Hand Main Board ...................................... 15
Base (Bottom) ................................................................... 16
Base Main Board ............................................................... 16
RF Unit (BU) .................................................................... 17
Base Key Board ................................................................. 17
3. ELECTRICAL ADJUSTMENTS
3-1. Handset .............................................................................. 18
3-2. Base Phone ........................................................................ 19
4. DIAGRAMS
4-1.
4-2.
4-3.
4-4.
4-5.
4-6.
4-7.
4-8.
4-9.
Block Diagram –Base Phone Section– ............................. 21
Block Diagram –Handset Section– ................................... 23
Schematic Diagram –Base Main Section (1/2)– ............... 25
Schematic Diagram –Base Main Section (2/2)– ............... 27
Printed Wiring Board –Base Main Section– ..................... 29
Printed Wiring Board –Base Key Section– ....................... 33
Schematic Diagram –Base Key Section– .......................... 35
Printed Wiring Board –Hand Main Section– .................... 37
Schematic Diagram –Hand Main Section– ....................... 39
5. EXPLODED VIEWS
5-1. Handset Section ................................................................. 42
5-2. Base Phone Section ........................................................... 43
6. ELECTRICAL PARTS LIST ........................................ 44
–2–
SECTION 1
GENERAL
–3–
This section is extracted from
SPP-ID975’s instruction manual.
–4–
–5–
–6–
–7–
–8–
–9–
– 10 –
– 11 –
– 12 –
– 13 –
– 14 –
SECTION 2
DISASSEMBLY
• The equipment can be removed using the following procedure.
HANDSET
CASE (REAR)
BASE PHONE
BASE (BOTTOM)
RF UNIT (HS), HAND MAIN BOARD
BASE MAIN BOARD
RF UNIT (BU)
BASE KEY BOARD
Note : Follow the disassembly procedure in the numerical order given.
2-1. CASE (REAR)
2 battery case lid (HS)
9 case (rear)
8
claw
6
4
3 BTP 3x12
1
4-7
7
5
2-2. RF UNIT (HS), HAND MAIN BOARD
antenna
(ANT1001)
1 BTP 3x12
8 RF unit (HS)
2 B 2x8
4 B 2x6
5 B 2x6
battery terminals
3 BTP 3x12
9 Removal the solders.
qa HAND MAIN board
7 Removal the solders.
6 VOL knob (HS)
charge terminals
0 Removal the solders.
– 15 –
2-3. BASE (BOTTOM)
2 BTP 3x12
6 base (bottom)
3 BTP 3x12
1 BTP 3x12
5
4
2-4. BASE MAIN BOARD
1 screws (3x30)
3 BTP 3x12
4 Removal the solders.
2 BTP 3x12
9 BASE MAIN board
5 Removal the solders.
battery terminal (BU)
7 Removal the solders.
6 Removal the solders.
charge springs
8 Removal the solders.
– 16 –
2-5. RF UNIT (BU)
1 BTP 3x12
3 B 2x8
lug
2 BTP 3x12
4 RF unit (BU)
2-6. BASE KEY BOARD
2 BTP 3x12
1 BTP 3x12
3 speaker holder
7 BASE KEY board
4 B 2x6
5 B 2x6
6 Removal the solders.
– 17 –
SECTION 3
ELECTRICAL ADJUSTMENTS
3-1. HANDSET
*
*
1. Test Mode
Entry— Press “PGM” key and enter “ TEST” on keypad.
Alternative entry— Write 99h into LSB of location 9 in EEPROM.
Exit— Press on “OFF” key.
LCD test— Press the “7” key.
Toggle TX power— Press the “0” key.
Increment RF channel— Press the “#” key.
2. Test Equipment Required and Connection
C1030
– HAND MAIN BOARD –
C1029
C1031
– RF UNIT (HS) –
J1003
BATTERY
3.6V
J1
U1001
J1004
frequency
counter
3. Verify Procedure
Item
18.4MHz Frequency Error
Remark
Connect the frequency counter to the test point J1, press “0” key to turn on the TX power. Then, check
the frequency ± 1 kHz. If the result is within ± 1 kHz, then no adjustment required. Otherwise, refer to
item 4. for Adjustment Procedure.
4. Adjustment Procedure
Item
18.4MHz Frequency Error
Adjustment Element
C1030
Remark
1. Remove C1031 from the HAND MAIN board.
2. Solder an 20PF chip capacitor C1030 (1-164-160-11) on the
HAND MAIN board (in parallel of C1029).
3. Connect the frequency counter to the test point J1. Adjust for 0 Hz ± 1 kHz.
– 18 –
3-2. BASE PHONE
1. Test Mode
Entry— Simultaneously press the “INTERCOM” key and toggle the “DIAL MODE” switch. When in test mode, the “LINE” and “CHARGE”
LEDs will be light on.
Alternative entry— Write 99h into LSB of location 9 in EEPROM.
Exit— Remove the AC power adaptor.
Toggle TX power— DIAL MODE switch (S3001)
T (TONE) position : TX ON
P (PULSE) position : TX OFF
Increment RF channel— Press the “INTERCOM” key.
2. Test Equipment Required and Connection
frequency
counter
– BASE MAIN BOARD
(SIDE B) –
– BASE MAIN BOARD
(SIDE A) –
– RF UNIT (BU) –
J1
U3003
C3015
C3012
C3002
3. Verify Procedure
Item
Remark
18.4MHz Frequency Error
Connect the frequency counter to the test point J1, press “0” key to turn on the TX power. Then, check
the frequency ± 1 kHz. If the result is within ± 1 kHz, then no adjustment required. Otherwise, refer to
item 4. for Adjustment Procedure.
4. Adjustment Procedure
Item
Adjustment Element
Remark
18.4MHz Frequency Error
C3015
1. Remove C3012 from the BASE MAIN board.
2. Solder an 20PF chip capacitor C3015 (1-164-160-11) on the
BASE MAIN board (in parallel of C3002).
3. Connect the frequency counter to the test point J1. Adjust for 0 Hz ± 1 kHz.
– 19 –
– 20 –
SPP-ID975/ID976
SECTION 4
DIAGRAMS
4-1. BLOCK DIAGRAM — BASE PHONE SECTION —
ANT3001
TELESCOPIC
ANTENNA
SYSTEM CONTROL
U3003
RF UNIT (BU)
D1007-1009
T1001
4
10
1
5
PLL EN 9
SER DATA OUT 8
SER CLK 7
67
64
68
79
58
RX AUDIO
TX DATA
PLL REF
RSSI
DSIN
TXDATA
PLL REF
APIN2
GPIO2/MONO2
CS
SK
DI
DO
1
2
3
4
55
63
62
59
P1.1 12
AIN 90
1
3
2
ADIN1 80
8
10
9
P1.0 11
14
12
13
GPIO5/TST1
SCLK
SOUT
SIN
RF POWER
CONTROL
Q3008
TX PWR 11
57 GPIO3/MON3
J1008
LINE
AON 84
EEPROM
U3007
RX PWR 3
HOOK DET
U1002
APO 83
5
6
7
AMP
U1003
X3001
18.4MHz
REG
U3008
48 XTAL2
49 XTAL1
FSK 89
SPEAKER AMP
U3005
RINGER 86
VIN
EAOUT 87
S3001
DIAL MODE
21 PXI
56 GPIO4/TST0
RECHARGEABLE
BATTERY
BP-T23
DC 3.6V
J1005
P
EAIN 88
11 PCLK
14 SER
42 GPIO0
L
5V
P6.5 8
!
REG
U1001
5
8
12 PCLK
Q7
7
Q6
6
76 REG CTRL
1
U3006
MIC
MCI 11
Q0-Q5 1-5
15
D14-20
(LCD BACK-LIGHT)
D7-9,11-13
LED POWER
CONTROL
Q3002,3005
P6.4 7
2 DVCC1
78 AVCC1
POWER
CONTROL
Q3001
P6.0 3
P6.1 4
P6.2 5
P6.3 6
P1.5 16
P1.6 17
P1.7 18
3.2V
CHARGE
TERMINAL
J1004
11
12
13
14
10
9
8
LCD DB4
LCD DB5
LCD DB6
LCD DB7
LCD E
LCD1
LCD MODULE
LCD R/W
LCD RS
Q1007
• Signal Path
HANDSET
CHARGE
Q1006
CHARGE DET
Q1008
04
14 P1.3
P5.0 30
I
I
P5.4 34
ROW0-ROW4
P4.0 35
I
I
P4.4 39
COL0-COL4
KEY MATRIX
S1-S21
: TX (To Tel Line)
: RX (From Tel Line)
: bell
– 21 –
SP1
SPEAKER
CD
12
74 VBAT
J1003
VO2
43 GPIO1
M
J1001
DC IN 9V
MUT
LED CONTROL
U3001
S3002
VOL
H
D10
SPARE BATTERY
5 HTO+
VO1
4
SPEECH PATH
U3004
T
J1002
BATT DET
Q1001
PXO 22
– 22 –
SPP-ID975/ID976
4-2. BLOCK DIAGRAM — HANDSET SECTION —
ANT1001
HELICAL ANTENNA
SYSTEM CONTROL
IC1001
RF UNIT (HS)
1
4
10
5
PLL EN 9
SER DATA OUT 8
SER CLK 7
64
67
68
79
58
PLL REF
RX AUDIO
TX DATA
RSSI
TX PWR 11
APO 83
AON 84
U1005
SPEAKER
CS
SK
DI
DO
EEPROM
U1006
1
2
3
4
RF POWER
CONTROL
Q1007
55
63
62
59
GPIO5/TST1
SCLK
SOUT
SIN
U1003
MIC
AIN 90
(LCD/KEY PAD BACK-LIGHT)
LED DRIVE
Q1002
P1.1 12
X1001
18.4MHz
U1002
BUZZER
RINGER OUT
Q1009
RINGER 86
RF POWER
CONTROL
Q1006
RX PWR 3
PLL REF
DSIN
TXDATA
ADIN2
GPIO2/MON2
48 XTAL2
49 XTAL1
LCD1001
LCD MODULE
56 GPIO4/TST0
57 GPIO3/MON3
H
REG
U1007
S103
VOL
80 ADIN1
M
L
J1003
S102
(ROTARY ENCODER)
3.6V
13 P1.2
14 P1.3
15 P1.4
RECHARGEABLE
BATTERY
BP-T23
DC 3.6V
P6.0 3
P6.1 4
P6.2 5
P6.3 6
P1.5 16
P1.6 17
P1.7 18
11
12
13
14
10
9
8
LCD DB4
LCD DB5
LCD DB6
LCD DB7
LCD E
LCD R/W
LCD RS
J1004
3.1V
D1003,1004
J1001
POWER
CONTROL
Q1004
REG
Q1010,1012
CHARGE
TERMINAL
2 DVCC1
78 AVCC1
76 REG CTRL
J1002
CHARGE DET
Q1008
11 P1.0
KEY MATRIX
S1023-S1044
P5.0 30
I
I
P5.4 34
ROW0-ROW4
P4.0 35
I
I
P4.4 39
COL0-COL4
04
• Signal Path
: TX (To Tel Line)
: RX (From Tel Line)
: bell
– 23 –
– 24 –
SPP-ID975/ID976
4-3. SCHEMATIC DIAGRAM — BASE MAIN SECTION (1/2) —
THIS NOTE IS COMMON FOR PRINTED WIRING
BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is
printed in each block.)
(Page 27)
For schematic diagrams
• All capacitors are in µF unless otherwise noted. pF: µµF
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
• C : panel designation.
• U : B+ Line.
• Power voltage is dc 9 V and fed with regulated dc power
supply from external power voltage jack. (BASE PHONE)
• Power voltage is dc 12 V and fed with regulated dc power
supply from J1008 with 100 Ω in series. (BASE PHONE)
• Power voltage is dc 3 V and fed with regulated dc power
supply from battery terminal. (HANDSET)
• Voltage is dc with respect to ground under no-signal
condition.
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tolerances.
• Signal path.
N : TX (To Tel Line)
O : RX (From Tel Line)
P : bell
For printed wiring boards
• X : parts extracted from the component side.
•
: Carbon pattern.
z
•
: Through hole.
• b : Pattern from the side which enables seeing.
(The other layer’s patterns are not indicated.)
Caution:
Pattern face side:
(Side B)
Parts face side:
(Side A)
Parts on the pattern face side seen from the
pattern face are indicated.
Parts on the parts face side seen from the
parts face are indicated.
– 25 –
– 26 –
SPP-ID975/ID976
4-4. SCHEMATIC DIAGRAM — BASE MAIN SECTION (2/2) — • Refer to page 41 for IC Block Diagrams.
(Page 26)
(Page 35)
RF UNIT
(BU)
– 27 –
– 28 –
SPP-ID975/ID976
4-5. PRINTED WIRING BOARD — BASE MAIN SECTION —
• Semiconductor
Location (side A)
Ref. No.
D1001
D1011
D1012
D1015
D1016
D3001
Location
F-5
G-5
H-5
H-4
H-4
C-8
Q1006
Q1008
Q3001
Q3002
Q3003
Q3005
G-6
H-6
C-6
C-9
B-6
D-9
U1003
U3001
U3003
U3004
U3005
U3007
U3008
G-5
B-8
D-7
B-7
B-9
C-7
A-6
– 29 –
– 30 –
SPP-ID975/ID976
• Semiconductor
Location (side B)
(Page 34)
– 31 –
– 32 –
Ref. No.
D1006
D1007
D1008
D1009
D1010
Location
G-2
F-2
F-2
F-2
F-2
Q1001
Q1007
E-4
G-9
U1001
U1002
F-4
F-3
SPP-ID975/ID976
4-6. PRINTED WIRING BOARD — BASE KEY SECTION —
(Page 31)
• Semiconductor Location
Ref. No.
D7
D8
D9
D10
D11
D12
D13
Location
D-3
C-3
C-3
E-7
C-8
E-8
A-8
Ref. No.
D14
D15
D16
D17
D18
D19
D20
– 33 –
Location
D-2
D-2
C-2
C-2
B-2
B-2
A-2
– 34 –
SPP-ID975/ID976
(Page 27)
4-7. SCHEMATIC DIAGRAM — BASE KEY SECTION —
– 35 –
– 36 –
SPP-ID975/ID976
4-8. PRINTED WIRING BOARD — HAND MAIN SECTION —
• Semiconductor
Location
Ref. No. Location
D1001
A-8
D1002
C-8
D1003
A-7
D1004
A-8
D1006
B-8
(D1009)
A-5
(D1011)
B-5
(D1017)
A-6
(D1019)
B-6
D1020
A-3
<D1023> A-2
<D1024> B-2
<D1025> B-2
<D1026> B-2
<D1027> A-2
<D1028> B-2
D1030
B-6
D1031
A-7
<D1032> C-2
<D1033> C-2
(
<
Q1002
Q1004
Q1006
Q1007
Q1008
Q1009
Q1010
Q1012
B-3
A-6
B-1
B-1
A-7
B-7
A-6
A-7
U1001
U1006
U1007
B-4
A-2
C-1
) : SIDE A,
SPP-ID976 only
> : SIDE A
– 37 –
– 38 –
SPP-ID975/ID976
4-9. SCHEMATIC DIAGRAM — HAND MAIN SECTION — • Refer to page 41 for IC Block Diagrams.
– 39 –
– 40 –
SECTION 5
EXPLODED VIEWS
ADDRESS
REGISTER
SHIFT
CLOCK
RESET
SERIAL DATA
OUTPUT
15
14
13
12
11
10
9
• -XX and -X mean standardized parts, so
they may have some difference from the
original one.
• Color Indication of Appearance Parts
Example :
KNOB, BALANCE (WHITE) ... (RED)
R
R
Parts Color Cabinet’s Color
SHIFT REGISTER
HIGH VOLTAGE
GENERATOR
AND
PROGRAM
TIMER
EEPROM ARRAY 16384 BIT
& (1024X16) or (2048X8)
ANT1001
19
LATCH
1
DATA OUT
BUFFER
2
3
5
9
QH
QF
4
QG
QE
QC
DATA IN/OUT RESISTER
16 (or 8) BITS
QD
QB
READ WRITE AMPS
DO 4
• Accessories and packing materials are
given in the last of this parts list.
5-1. HANDSET SECTION
6 ORG
DECODER
IOF 1024
(or 2048)
NOTE:
• The mechanical parts with no reference
number in the exploded views are not supplied.
• Items marked “*” are not stocked since
they are seldom required for routine service.
Some delay should be anticipated
when ordering these items.
SQH
LATCH
CLOCK
16
VCC
7 NC
A
INSTRUCTION
REGISTER
DI 3
8 VCC
INSTRUCTION
DECODER, CONTROL
LOGIC AND CLOCK
GENERATORS
QA
CS 1
SK 2
OUTPUT
ENABLE
U1006, 3007 CAT93C86S-LE10
SERIAL DATA
INPUT
U3001 MC74HC595AF
PARALLEL DATA
OUTPUT
• IC Block Diagrams
6
7
U1005
5 VSS
PARALLEL DATA
OUTPUT
7
6
U3005 MC34119D
12
VO2
GND
Vcc
VO1
15
8
7
6
5
11
9
8
GND
8
10
13
16 14
_
9
+
BIAS
CIRCUIT
+
_
9 13
5
3
4
V in
CD
CF 2
2
CF 1
U1003
1
J1003, 1004
RLI2
RLO2
TLO2
TLI2
CPT
V8
24
RX1
25
TU1
26
RX0
TLO1
27
PU1
CPR
28
PLO1
GND
U3004 MC34118DW
23
22
21
20
19
18
17
16
15
4
3
J1001, 1002
17
R
400
BACK GROUND
NOISE MONITER
18
2
LEVEL DET
R
LCD1001
VCC
BIAS
DP-DET
–
1
AGC
+
RX ATT
Ref. No.
15mV
BACK GROUND
NOISE MONITER
VR
ATT CONTROL
LEVEL DET
TX ATT
VR
FILTER
+
R
–
–
R
–
Description
3-038-148-01
3-038-148-11
3-038-075-01
3-041-211-01
3-038-081-01
KEY (HS), RUBBER (ID975)
KEY (HS), RUBBER (ID976)
CASE (FR)
RUBBER, MICROPHONE
LENS (HS)
Remark
Ref. No.
Part No.
Description
15
* 16
* 16
17
18
3-041-535-01
A-3672-876-A
A-3672-897-A
3-038-084-01
3-041-536-01
FELT, RX
HAND MAIN BOARD, COMPLETE (ID975)
HAND MAIN BOARD, COMPLETE (ID976)
DIFFUSER (HS)
SHEET
Remark
5
6
7
8
9
3-041-520-01
3-041-537-01
3-041-212-01
A-3672-875-A
7-685-548-19
HOLDER (HS), LCD
RING, CUSHION RECEIVER
CUSHION, SPEAKER
RF UNIT (HS)
SCREW +BTP 3X12 TYPE2 N-S
19
3-041-547-01
ANT1001 1-754-103-11
J1001 3-041-208-01
J1002 3-041-208-01
J1003 3-041-210-01
COVER (HS), HOOK
ANTENNA
TERMINAL, CHARGE
TERMINAL, CHARGE
TERMINAL, BATTERY
10
11
12
13
14
3-038-076-01
3-038-083-01
4-356-741-21
4-356-741-11
3-038-085-01
CASE (REAR)
LID (HS), BATTERY CASE
SCREW, TAPPING (BIND 2X8)
SCREW, TAPPING (BIND 2X6)
KNOB (HS), VOLUME
J1004 3-041-210-01
LCD1001 1-803-832-11
U1003 1-542-260-31
U1005 1-505-593-11
TERMINAL, BATTERY
LCD MODULE
MICROPHONE, ELECTRET CONDENSER
SPEAKER (2.8cm)
+
+
VR
+
Part No.
1
1
2
3
4
–
2
3
4
5
6
7
8
9
10
11
12
13
14
FO
FI
CO
Vcc
HTO(+)
HTO(–)
NTI
TXO
TXI
WCO
WCI
MUTE
VCL
CT
VR
1
– 41 –
– 42 –
5-2. BASE PHONE SECTION
64
65
67
66
SP1
62
ANT3001
63
68
61
52
A
79
78
77
60
52
69
52
80
U3006
59
53
54
76
LCD1
70
A
52
58
57
J1002, 1005
55
56
55
55
71
75
72
52
52
73
J1003, 1004
74
72
52
51
52
52
Ref. No.
Part No.
Description
Part No.
Description
* 51
52
53
54
55
A-3672-878-A
7-685-548-19
3-044-144-01
3-041-523-01
4-356-741-11
BASE MAIN BOARD, COMPLETE
SCREW +BTP 3X12 TYPE2 N-S
TERMINAL BOARD, ANTENNA
RINGER (SW), KNOB
SCREW, TAPPING (BIND 2X6)
Remark
Ref. No.
70
71
72
73
74
4-356-741-21
3-038-069-01
3-041-534-01
3-044-147-01
3-044-146-01
SCREW, TAPPING (BIND 2X8)
BASE (BOTTOM)
FOOT, RUBBER
SPONGE, MICROPHONE
SCREW (3X30)
* 56
57
58
59
60
1-676-042-11
3-041-552-01
3-041-536-01
3-041-532-01
3-041-550-01
BASE KEY BOARD
DIFFUSION (BU)
SHEET
CUSHION (BU), MICROPHONE
HOLDER (BU), MICROPHONE
75
76
77
78
79
3-041-551-01
3-041-563-01
3-038-067-01
3-044-143-01
3-041-552-01
BASE, STUD
PAD (975), FUNCTION KEY
BASE, KEY
PLATE, ANTENNA RETAINER
HOLDER (BU975), LCD
61
62
63
64
64
3-038-072-01
3-038-660-01
3-038-066-01
3-038-068-01
3-038-068-11
GUIDE, LIGHT
LID (BU), BATTERY CASE
BASE (TOP)
BASE, LENS (ID975)
BASE, LENS (ID976)
80
3-038-077-01
ANT3001 1-501-951-31
J1002 3-041-209-01
J1003 3-041-530-01
J1004 3-041-530-01
KNOB, TP SW
ANTENNA
SPRING, CHARGE
TERMINAL (BU), BATTERY
TERMINAL (BU), BATTERY
65
66
67
68
69
3-041-553-01
3-038-090-01
3-041-275-01
3-041-274-01
A-3672-877-A
KEY (BU975), VOLUME
HOOK
PACKING, SPEAKER
HOLDER, SPEAKER
RF UNIT (BU)
J1005
LCD1
SP1
U3006
SPRING, CHARGE
LCD MODULE
SPEAKER (5cm)
MICROPHONE, ELECTRET CONDENSER
– 43 –
3-041-209-01
1-803-833-11
1-505-231-11
1-542-118-41
Remark
BASE KEY
SECTION 6
ELECTRICAL PARTS LIST
BASE MAIN
NOTE:
• Due to standardization, replacements in
the parts list may be different from the
parts specified in the diagrams or the
components used on the set.
• -XX and -X mean standardized parts, so
they may have some difference from the
original one.
• RESISTORS
All resistors are in ohms.
METAL:Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F:nonflammable
• Items marked “*” are not stocked since
they are seldom required for routine service.
Some delay should be anticipated
when ordering these items.
• SEMICONDUCTORS
In each case, u : µ, for example:
uA.. : µA.. uPA.. : µPA..
uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD..
• CAPACITORS
uF : µF
• COILS
uH : µH
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
Les composants identifiés par une
marque 0 sont critiques pour
la sécurité.
Ne les remplacer que par une piéce
portant le numéro spécifié.
When indicating parts by reference
number, please include the board.
Ref. No.
Part No.
Description
Remark
*
1-676-042-11 BASE KEY BOARD
***************
< CAPACITOR >
C1
C2
C4
1-126-963-11 ELECT
1-126-963-11 ELECT
1-107-826-11 CERAMIC CHIP
4.7uF
4.7uF
0.1uF
20%
20%
10%
50V
50V
16V
< DIODE >
D7
D8
D9
D10
D11
8-719-059-40
8-719-059-40
8-719-052-06
8-719-059-40
8-719-059-40
LED
LED
LED
LED
LED
SLR-342VR3F (NEW CALL)
SLR-342VR3F (MESSAGES)
SLR-342MGT32 (LINE)
SLR-342VR3F (SPARE BATTERY)
SLR-342VR3F (SPEAKERPHONE)
D12
D13
D14
D15
D16
8-719-059-40
8-719-059-40
8-719-060-99
8-719-060-99
8-719-060-99
LED
LED
LED
LED
LED
SLR-342VR3F (CHARGE)
SLR-342VR3F (INTERCOM)
SML-210MT-T86 (LCD BACK LIGHT)
SML-210MT-T86 (LCD BACK LIGHT)
SML-210MT-T86 (LCD BACK LIGHT)
D17
D18
D19
D20
8-719-060-99
8-719-060-99
8-719-060-99
8-719-060-99
LED
LED
LED
LED
SML-210MT-T86 (LCD BACK LIGHT)
SML-210MT-T86 (LCD BACK LIGHT)
SML-210MT-T86 (LCD BACK LIGHT)
SML-210MT-T86 (LCD BACK LIGHT)
< CONNECTOR >
J1
1-766-448-11 CONNECTOR, FFC/FPC (ZIF) 14P
< COIL >
L1
L2
1-408-117-00 INDUCTOR
1-408-117-00 INDUCTOR
10uH
10uH
< RESISTOR >
R3
1-216-858-11 RES,CHIP
1.2M
5%
1/16W
R4
1-214-733-00 METAL
1.5K
1%
1/4W
*************************************************************
A-3672-878-A BASE MAIN BOARD, COMPLETE
**************************
*
< CAPACITOR >
C1001
C1002
C1003
C1004
C1006
1-104-665-11
1-107-826-11
1-107-826-11
1-126-933-11
1-102-973-00
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC
100uF
0.1uF
0.1uF
100uF
100PF
20%
10%
10%
20%
5%
25V
16V
16V
16V
50V
Ref. No.
Part No.
Description
C1007
C1008
C1009
C1010
C1012
1-102-973-00
1-102-973-00
1-109-994-11
1-165-176-11
1-162-979-11
CERAMIC
CERAMIC
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
100PF
2.2uF
0.047uF
0.0027uF
5%
5%
10%
10%
10%
50V
50V
10V
16V
50V
C1013
C1014
C1015
C1016
C1017
1-107-826-11
1-107-826-11
1-162-979-11
1-107-975-11
1-162-114-00
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC
CERAMIC
0.1uF
0.1uF
0.0027uF
33PF
0.0047uF
10%
10%
10%
10%
10%
16V
16V
50V
3KV
2KV
C1018
C1020
C1021
C1022
C1023
1-162-927-11
1-107-975-11
1-162-114-00
1-162-927-11
1-107-826-11
CERAMIC CHIP
CERAMIC
CERAMIC
CERAMIC CHIP
CERAMIC CHIP
100PF
33PF
0.0047uF
100PF
0.1uF
5%
10%
10%
5%
10%
50V
3KV
2KV
50V
16V
C1024
C1025
C1026
C1027
C1028
1-162-919-11
1-164-227-11
1-164-227-11
1-165-176-11
1-165-176-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
22PF
0.022uF
0.022uF
0.047uF
0.047uF
5%
10%
10%
10%
10%
50V
25V
25V
16V
16V
C1029
C1030
C1031
C1032
C3001
1-162-919-11
1-107-826-11
1-128-582-11
1-107-826-11
1-162-964-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
22PF
0.1uF
10uF
0.1uF
0.001uF
5%
10%
20%
10%
10%
50V
16V
6.3V
16V
50V
C3002
C3003
C3004
C3005
C3006
1-162-912-11
1-107-826-11
1-126-964-11
1-126-960-11
1-126-964-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
ELECT
7PF
0.1uF
10uF
1uF
10uF
0.5PF
10%
20%
20%
20%
50V
16V
50V
50V
50V
C3007
C3008
C3009
C3010
C3011
1-107-826-11
1-162-919-11
1-162-919-11
1-162-962-11
1-164-227-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
22PF
22PF
470PF
0.022uF
10%
5%
5%
10%
10%
16V
50V
50V
50V
25V
C3012
C3013
C3014
C3015
C3016
1-162-964-11
1-126-964-11
1-107-826-11
1-107-826-11
1-107-826-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
10uF
0.1uF
0.1uF
0.1uF
10%
20%
10%
10%
10%
50V
50V
16V
16V
16V
C3017
C3021
C3022
C3023
C3024
1-162-918-11
1-107-826-11
1-162-962-11
1-107-826-11
1-164-677-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
18PF
0.1uF
470PF
0.1uF
0.033uF
5%
10%
10%
10%
10%
50V
16V
50V
16V
16V
– 44 –
Remark
BASE MAIN
Ref. No.
Part No.
Description
C3025
C3026
C3027
C3028
C3029
1-107-826-11
1-107-826-11
1-126-961-11
1-165-176-11
1-126-933-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
0.1uF
0.1uF
2.2uF
0.047uF
100uF
10%
10%
20%
10%
20%
Remark
16V
16V
50V
16V
16V
C3030
C3031
C3032
C3033
C3034
1-165-176-11
1-107-826-11
1-107-826-11
1-107-826-11
1-126-961-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.047uF
0.1uF
0.1uF
0.1uF
2.2uF
10%
10%
10%
10%
20%
16V
16V
16V
16V
50V
C3035
C3036
C3037
C3038
C3039
1-126-961-11
1-104-664-11
1-104-664-11
1-126-963-11
1-162-970-11
ELECT
ELECT
ELECT
ELECT
CERAMIC CHIP
2.2uF
47uF
47uF
4.7uF
0.01uF
20%
20%
20%
20%
10%
50V
16V
16V
50V
25V
C3040
C3041
C3042
C3043
C3045
1-162-964-11
1-102-973-00
1-102-973-00
1-162-964-11
1-126-960-11
CERAMIC CHIP
CERAMIC
CERAMIC
CERAMIC CHIP
ELECT
0.001uF
100PF
100PF
0.001uF
1uF
10%
5%
5%
10%
20%
50V
50V
50V
50V
50V
C3046
C3047
C3048
C3049
C3050
1-164-217-11
1-162-964-11
1-162-964-11
1-126-960-11
1-126-964-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
ELECT
150PF
0.001uF
0.001uF
1uF
10uF
5%
10%
10%
20%
20%
50V
50V
50V
50V
50V
C3055
C3056
C3059
C3060
C3062
1-107-826-11
1-107-826-11
1-107-826-11
1-162-964-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.001uF
0.1uF
10%
10%
10%
10%
10%
16V
16V
16V
50V
16V
C3063
C3064
C3065
C3066
C3067
1-107-826-11
1-107-826-11
1-107-826-11
1-107-826-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
16V
16V
16V
16V
16V
C3070
C3071
C3072
C3073
C3074
1-107-826-11
1-107-826-11
1-127-675-11
1-127-692-11
1-127-692-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
22uF
10uF
10uF
10%
10%
10%
10%
10%
16V
16V
10V
16V
16V
Ref. No.
Part No.
Description
Remark
< JACK >
J1001
J1008
1-580-727-11 JACK (DC IN 9V)
1-565-999-11 JACK, MODULAR 2P (LINE)
< COIL >
< DIODE >
D1001
D1006
D1007
D1008
D1009
8-719-047-37
1-801-730-11
8-719-911-55
8-719-911-55
8-719-911-55
DIODE BAS16
VARISTOR
DIODE 1N4004
DIODE 1N4004
DIODE 1N4004
D1010
D1011
D1012
D1015
D1016
8-719-911-55
8-719-909-90
8-719-909-90
8-719-909-90
8-719-909-90
DIODE
DIODE
DIODE
DIODE
DIODE
D3001
8-719-077-35 DIODE BB555
1N4004
BAV99
BAV99
BAV99
BAV99
L1001
L1003
L1004
L1005
L1006
1-408-117-00
1-408-117-00
1-408-117-00
1-408-117-00
1-408-117-00
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
INDUCTOR
10uH
10uH
10uH
10uH
10uH
< TRANSISTOR >
Q1001
Q1006
Q1007
Q1008
Q3001
8-729-113-08
8-729-026-06
8-729-820-84
8-729-026-06
8-729-922-00
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
2N3906
MMBT3904LT1
2SC2812
MMBT3904LT1
MMST2907A
Q3002
Q3003
Q3005
8-729-026-06 TRANSISTOR MMBT3904LT1
8-729-026-07 TRANSISTOR MMBT3906LT1
8-729-026-07 TRANSISTOR MMBT3906LT1
< RESISTOR >
R1001
R1002
R1010
R1011
R1012
1-216-057-00
1-259-880-11
1-216-841-11
1-216-833-11
1-216-828-11
METAL CHIP
CARBON
METAL CHIP
METAL CHIP
METAL CHIP
2.2K
2.2M
47K
10K
3.9K
5%
5%
5%
5%
5%
1/10W
1/4W
1/16W
1/16W
1/16W
R1015
R1016
R1017
R1018
R1019
1-216-151-00
1-216-833-11
1-216-833-11
1-216-825-11
1-216-845-11
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
11
10K
10K
2.2K
100K
5%
5%
5%
5%
5%
1/8W
1/16W
1/16W
1/16W
1/16W
R1020
R1021
R1022
R1023
R1024
1-216-818-11
1-216-820-11
1-216-812-11
1-216-812-11
1-218-345-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
RES,CHIP
560
820
180
180
9.1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R1025
R1026
R1027
R1028
R1031
1-216-837-11
1-218-292-11
1-218-292-11
1-216-833-11
1-259-880-11
METAL CHIP
RES,CHIP
RES,CHIP
METAL CHIP
CARBON
22K
20K
20K
10K
2.2M
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/4W
R1032
R1034
R1035
R1036
R1037
1-219-570-11
1-259-880-11
1-219-570-11
1-220-869-11
1-220-869-11
METAL CHIP
CARBON
METAL CHIP
RES,CHIP
RES,CHIP
10M
2.2M
10M
1.6M
1.6M
5%
5%
5%
5%
5%
1/16W
1/4W
1/16W
1/16W
1/16W
R1038
R1039
R1042
R1043
R1044
1-216-833-11
1-216-833-11
1-216-848-11
1-216-845-11
1-219-570-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
180K
100K
10M
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
– 45 –
BASE MAIN
Ref. No.
HAND MAIN
Part No.
Description
Part No.
Description
R1045
R1046
R1047
R1048
R1049
1-219-570-11
1-216-857-11
1-216-857-11
1-216-833-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10M
1M
1M
10K
10K
5%
5%
5%
5%
5%
Remark
1/16W
1/16W
1/16W
1/16W
1/16W
Ref. No.
R3058
R3059
R3060
R3061
R3062
1-216-848-11
1-216-848-11
1-216-839-11
1-216-825-11
1-216-848-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
180K
180K
33K
2.2K
180K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
Remark
R1050
R3002
R3003
R3004
R3005
1-218-288-11
1-216-833-11
1-216-833-11
1-216-833-11
1-216-864-11
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
300
10K
10K
10K
0
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R3066
R3067
R3068
R3069
R3070
1-216-864-11
1-216-864-11
1-216-835-11
1-216-825-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
15K
2.2K
1K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R3006
R3007
R3008
R3009
R3011
1-216-864-11
1-218-161-11
1-216-846-11
1-216-821-11
1-216-861-11
METAL CHIP
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
62K
120K
1K
2.2M
5%
1%
5%
5%
5%
1/16W
1/10W
1/16W
1/16W
1/16W
R3012
R3014
R3015
R3016
R3017
1-218-292-11
1-218-166-11
1-218-161-11
1-216-833-11
1-216-829-11
RES,CHIP
RES,CHIP
RES,CHIP
METAL CHIP
METAL CHIP
20K
300K
62K
10K
4.7K
5%
1%
1%
5%
5%
1/16W
1/10W
1/10W
1/16W
1/16W
R3018
R3019
R3020
R3021
R3022
1-216-833-11
1-216-813-11
1-216-823-11
1-216-813-11
1-216-813-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
220
1.5K
220
220
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R3023
R3024
R3025
R3026
R3029
1-216-813-11
1-218-292-11
1-216-841-11
1-218-292-11
1-216-864-11
METAL CHIP
RES,CHIP
METAL CHIP
RES,CHIP
METAL CHIP
220
20K
47K
20K
0
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R3030
R3031
R3032
R3033
R3034
1-216-833-11
1-216-805-11
1-216-833-11
1-216-833-11
1-216-813-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
47
10K
10K
220
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R3035
R3036
R3038
R3039
R3040
1-216-813-11
1-216-823-11
1-218-345-11
1-216-839-11
1-216-846-11
METAL CHIP
METAL CHIP
RES,CHIP
METAL CHIP
METAL CHIP
220
1.5K
9.1K
33K
120K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R3041
R3042
R3043
R3044
R3045
1-218-290-11
1-216-833-11
1-216-833-11
1-216-828-11
1-216-845-11
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
6.2K
10K
10K
3.9K
100K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R3046
R3047
R3048
R3049
R3050
1-216-849-11
1-216-849-11
1-218-272-11
1-218-272-11
1-216-845-11
METAL CHIP
METAL CHIP
RES,CHIP
RES,CHIP
METAL CHIP
220K
220K
5.1K
5.1K
100K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R3051
R3056
R3057
1-216-831-11 METAL CHIP
1-218-293-11 RES,CHIP
1-218-293-11 RES,CHIP
6.8K
24K
24K
5%
5%
5%
1/16W
1/16W
1/16W
< SWITCH >
S3001
S3002
1-571-377-11 SWITCH, SLIDE (DIAL MODE)
1-771-833-11 SWITCH, SLIDE (VOL)
< TRANSFORMER >
T1001
1-431-965-11 TRANSFORMER, LINE
< IC >
U1001
U1002
U1003
U3001
U3003
8-759-391-69
8-759-514-42
8-759-701-36
8-759-032-59
X-3378-159-1
IC MC78M05CDT
IC AM27C010-100DC
IC NJM3403AM
IC MC74HC595AF
ASIC ASSY (ASIC BOARD, COMPLETE)
U3004
U3005
U3006
U3007
U3008
8-759-030-78
8-759-463-98
1-542-118-41
8-759-466-52
8-759-651-11
IC MC34118DW
IC MC34119D
MICROPHONE, ELECTRET CONDENSER
IC CAT93C86S-LE10
IC LP29811M5-3.0
< FUSE >
W1001
1-533-842-11 FUSE (250mA/250V)
< VIBRATOR >
X3001 1-577-269-11 VIBRATOR, CRYSTAL (18.4MHz)
*************************************************************
A-3672-876-A HAND MAIN BOARD, COMPLETE (ID975)
A-3672-897-A HAND MAIN BOARD, COMPLETE (ID976)
***************************
*
*
< CAPACITOR >
C1001
C1002
C1003
C1004
C1005
1-162-964-11
1-162-970-11
1-107-826-11
1-107-826-11
1-164-346-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.01uF
0.1uF
0.1uF
1uF
10%
10%
10%
10%
50V
25V
16V
16V
16V
C1006
C1009
C1011
C1012
C1013
1-162-970-11
1-164-346-11
1-107-826-11
1-110-501-11
1-135-201-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
0.01uF
1uF
0.1uF
0.33uF
10uF
10%
10%
10%
20%
25V
16V
16V
16V
4V
C1014
1-107-826-11 CERAMIC CHIP
0.1uF
10%
16V
– 46 –
HAND MAIN
Ref. No.
Part No.
Description
C1015
C1016
C1017
C1018
C1019
1-107-826-11
1-162-919-11
1-164-227-11
1-162-918-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
22PF
0.022uF
18PF
0.1uF
10%
5%
10%
5%
10%
Remark
16V
50V
25V
50V
16V
C1020
C1021
C1022
C1024
C1025
1-135-201-11
1-107-826-11
1-162-962-11
1-107-826-11
1-162-964-11
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10uF
0.1uF
470PF
0.1uF
0.001uF
20%
10%
10%
10%
10%
4V
16V
50V
16V
50V
C1026
C1027
C1028
C1029
C1031
1-107-826-11
1-135-201-11
1-162-915-11
1-162-912-11
1-162-964-11
CERAMIC CHIP
TANTALUM CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
10uF
10PF
7PF
0.001uF
10%
20%
0.5PF
0.5PF
10%
16V
4V
50V
50V
50V
C1038
C1039
C1040
C1041
C1042
1-107-826-11
1-107-826-11
1-135-181-21
1-135-181-21
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
TANTALUM CHIP
TANTALUM CHIP
CERAMIC CHIP
0.1uF
0.1uF
4.7uF
4.7uF
0.1uF
10%
10%
20%
20%
10%
16V
16V
6.3V
6.3V
16V
C1043
C1047
C1048
C1049
C1050
1-107-826-11
1-107-826-11
1-107-826-11
1-107-826-11
1-127-692-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
0.1uF
10uF
10%
10%
10%
10%
10%
16V
16V
16V
16V
16V
C1051
C1052
C1053
C1054
1-127-692-11
1-127-675-11
1-162-964-11
1-165-176-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
10uF
22uF
0.001uF
0.047uF
10%
10%
10%
10%
16V
10V
50V
16V
Ref. No.
Part No.
Description
Remark
< TRANSISTOR >
Q1002
Q1004
Q1006
Q1007
Q1008
8-729-026-07
8-729-922-00
8-729-026-07
8-729-026-07
8-729-026-06
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
MMBT3906LT1
MMST2907A
MMBT3906LT1
MMBT3906LT1
MMBT3904LT1
Q1009
Q1010
Q1012
8-729-026-06 TRANSISTOR MMBT3904LT1
8-729-922-00 TRANSISTOR MMST2907A
8-729-033-61 TRANSISTOR MMBT2222ALT1
< RESISTOR >
R1001
R1002
R1003
R1004
R1006
1-216-833-11
1-216-833-11
1-216-853-11
1-216-853-11
1-216-818-11
R1007
R1008
R1009
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
10K
470K
470K
560
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
1-216-156-00 RES,CHIP
1-216-818-11 METAL CHIP
1-216-803-11 METAL CHIP
18
560
33
5%
5%
5%
R1009
1-216-804-11 METAL CHIP
39
5%
R1010
1-216-803-11 METAL CHIP
33
5%
1/8W
1/16W
1/16W
(ID976)
1/16W
(ID975)
1/16W
(ID976)
R1010
1-216-804-11 METAL CHIP
39
5%
R1014
R1021
R1022
R1025
1-216-800-11
1-216-827-11
1-216-823-11
1-219-614-11
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
18
3.3K
1.5K
301K
1/16W
(ID975)
5%
1/16W
5%
1/16W
5%
1/16W
0.50% 1/16W
R1026
R1027
R1031
R1032
R1033
1-218-161-11
1-216-833-11
1-218-161-11
1-220-372-11
1-216-845-11
RES,CHIP
METAL CHIP
RES,CHIP
RES,CHIP
METAL CHIP
62K
10K
62K
200K
100K
1%
5%
1%
5%
5%
1/10W
1/16W
1/10W
1/16W
1/16W
R1035
R1036
R1037
R1039
R1041
1-216-841-11
1-218-292-11
1-216-821-11
1-216-846-11
1-216-861-11
METAL CHIP
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47K
20K
1K
120K
2.2M
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R1042
R1044
R1057
R1058
R1059
1-216-833-11
1-218-292-11
1-216-823-11
1-216-833-11
1-216-823-11
METAL CHIP
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
20K
1.5K
10K
1.5K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R1060
R1064
R1065
R1066
R1067
1-216-833-11
1-216-836-11
1-218-271-11
1-218-331-11
1-216-845-11
METAL CHIP
METAL CHIP
RES,CHIP
RES,CHIP
METAL CHIP
10K
18K
2K
51K
100K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
R1068
R1069
R1070
1-216-821-11 METAL CHIP
1-216-833-11 METAL CHIP
1-216-821-11 METAL CHIP
1K
10K
1K
5%
5%
5%
1/16W
1/16W
1/16W
< DIODE >
D1001
D1002
D1003
D1004
D1006
1-801-730-11
1-801-730-11
8-719-909-90
8-719-909-90
8-719-047-37
VARISTOR
VARISTOR
DIODE BAV99
DIODE BAV99
DIODE BAS16
D1009
D1011
D1017
D1019
D1020
8-719-063-83
8-719-063-83
8-719-063-83
8-719-063-83
8-719-077-35
LED SML-310MTT86 (ID976)
LED SML-310MTT86 (ID976)
LED SML-310MTT86 (ID976)
LED SML-310MTT86 (ID976)
DIODE BB555
D1023
D1024
D1025
D1026
D1027
8-719-063-83
8-719-063-83
8-719-063-83
8-719-063-83
8-719-063-83
LED
LED
LED
LED
LED
D1028
D1030
D1031
D1032
D1033
8-719-063-83
8-719-047-37
8-719-070-56
8-719-063-83
8-719-063-83
LED SML-310MTT86
DIODE BAS16
DIODE PDZ5.1B-115
LED SML-310MTT86
LED SML-310MTT86
SML-310MTT86
SML-310MTT86
SML-310MTT86
SML-310MTT86
SML-310MTT86
– 47 –
SPP-ID975/ID976
HAND MAIN
Ref. No.
Part No.
Description
R1071
R1073
R1076
R1079
R1083
1-216-852-11
1-220-151-11
1-216-845-11
1-216-864-11
1-216-849-11
METAL CHIP
RES,CHIP
METAL CHIP
METAL CHIP
METAL CHIP
R1084
R1086
1-216-864-11 METAL CHIP
1-216-835-11 METAL CHIP
Remark
390K
51
100K
0
220K
5%
5%
5%
5%
5%
1/16W
1/16W
1/16W
1/16W
1/16W
0
15K
5%
5%
1/16W
1/16W
< SWITCH >
S1002
S1003
1-475-568-12 ENCODER, ROTARY
1-771-833-11 SWITCH, SLIDE (VOL)
< IC >
U1001
U1002
U1003
U1005
U1006
X-3378-159-1
1-505-594-11
1-542-260-31
1-505-593-11
8-759-466-52
ASIC ASSY (ASIC BOARD, COMPLETE)
BUZZER
MICROPHONE, ELECTRET CONDENSER
SPEAKER (2.8cm)
IC CAT93C86S-LE10
U1007
8-759-651-11 IC LP29811M5-3.0
< VIBRATOR >
X1001 1-577-269-11 VIBRATOR, CRYSTAL (18.4MHz)
*************************************************************
MISCELLANEOUS
***************
8
A-3672-875-A
69
A-3672-877-A
ANT1001 1-754-103-11
ANT3001 1-501-951-31
LCD1
1-803-833-11
RF UNIT (HS) (HANDSET)
RF UNIT (BU) (BASE PHONE)
ANTENNA (HANDSET)
ANTENNA (BASE PHONE)
LCD MODULE (BASE PHONE)
LCD1001 1-803-832-11 LCD MODULE (HANDSET)
SP1
1-505-231-11 SPEAKER (5cm) (BASE PHONE)
*************************************************************
ACCESSORIES & PACKING MATERIALS
********************************
0
1-475-852-11
1-528-769-11
1-696-453-21
1-696-454-11
3-012-379-11
ADAPTOR, AC (AC-T122)
BATTERY PACK (BP-T23)
CORD (WITH MODULAR PLUG) (LINE) (215cm)
CORD (WITH MODULAR PLUG) (LINE) (15cm)
CASE (WALL HOOK)
3-867-314-11 MANUAL, INSTRUCTION (ENGLISH,SPANISH)
(ID975)
3-867-314-21 MANUAL, INSTRUCTION (ENGLISH,FRENCH)
(ID976)
3-867-350-11 GUIDE, QUICK START (ENGLISH,SPANISH)
(ID975)
3-867-350-21 GUIDE, QUICK START (ENGLISH,FRENCH)
(ID976)
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
Sony Corporation
9-927-613-11
Personal Audio Division Company
– 48 –
Les composants identifiés par une
marque 0 sont critiques pour
la sécurité.
Ne les remplacer que par une piéce
portant le numéro spécifié.
99K0414-1
Printed in Japan ©1999. 11
Published by General Engineering Dept.