model 5640 - Spudnik Digital Implements

Transcription

model 5640 - Spudnik Digital Implements
OPERATORS & PARTS MANUAL
MODEL 5640
HARVESTER
PART # 290194
Mission Statement
Our mission is to consistently provide high
quality, reliable safe and well-designed
products serves to meet and exceed the
needs of our customers.
Service Centers
Phone: (208) 785-0480
E-Mail: [email protected]
Web Site: www.spudnik.com
BLACKFOOT
584 West 100 North
P.O. Box 1045
Blackfoot, ID 83221
Phone (208) 785-0480
Fax (208) 785-1497
HEYBURN
300 Centennial Dr.
Heyburn, ID 83336
Phone (208) 436-8052
Fax (208) 495-9170
PASCO
5802 N. Industrial Way Suite #D
Pasco, WA 99301
Phone (509) 543-7166
Fax (509) 543-7169
Parts Fax (509) 543-7186
GRAFTON
1 St. :HVW
*UDIWRQ, N' 5827
Phone (701) -
Fax (701) -
PRESQUE ISLE
80B Airport Drive
Presque Isle, ME
Phone (207) 764-4686
Fax (207) 764-4674
Table Of Contents
Page #
Description_______________________________________________________
Introduction ……………………………………………………………………………...
5
Forward to the Operation Manual ...……………………...…………………………...
6
Warranty …...…………………………………………………………………………...
7
General …..……………………………………………………………………………...
8
Product Characteristics …..…….……………………………………………………...
9
Dangers, operation errors and exemption from liability …………………………...
10
Safety ……………...…………………………………………………………………...
11
General safety and accident prevention regulations ……………………………...
12
Special safety instructions ..…………………………………………………………..
13
Towed machines ……………………………………………………………...
13
Using a power take-off …...…………………………………………………...
14
Electrical system, electronics ...……………………………………………..
14
Hydraulic system ……………………………………………………………….
15
Warning symbols and other instruction notices on the machine ………………... 16-18
19
Configuration and functions of the machine (Operation of machine)……………..
Harvester Tractor Connection ...………………………………………..…… 20-21
Camera Systems……………………………………………………………….. 22-23
Control Panel …………………………………………………………………… 24-27
28
Electrical ………………………………………………………………...………
Pre Dig Test ……..………………………………………………………...……
29
Drive Sensors ………………………………………………...………..
29
Boom lift………………....………………………………………………..
29
Back to Center Sensor……..…………………………………………...
30
Field Test Dig….…………………………………………………………….…….
31
Digger Nose ………………………………………………………………
31
Blade Angle ………………………………………………………………
31
Setting Draw Angle for Digger Nose ...…………………………………
32
Limiter Chain Adjustment...………………………………………………
33
Belted Chain Speed .………….…………………………………………
34
Table Of Contents
Description______________________________________________________Page #
Side Elevator & Eliminator Sprocket ….…………………………….
35
Rear Cross Angle Adjustment ………………………………………
36
Side Elevator and Hopper Adjustment ….………………………….
37
Cleaning Table Adjustment .…………………………………………
38
Roller Star Table …………..………………………………………….
38
Shakers ………...………………………………………………………
39
Harvester Trouble Shooting……………….………………………………….....…..... 41-43
44
Maintenance ……………………...……………………………………………..…….
General Safety Instructions .………………………………………….…....... 44-45
46
Special Safety Instructions ..………………………………………..………..
Spare Parts Procurement ……………………………………………..……..
47
Disposing of Replace Parts …………………….…………………..………..
47
Cleaning After Every Operation …...…………………………………..…….
48
Parts to be Cleaned ……………………………………………………...…….
49
Cleaning with High-pressure Cleaning Equipment …………...……..…….
49
Storage …………....…………………………………………………...….…..
50
Shortening/Repairing the Main Webs ………………………………..…..… 51-53
54
Screwed Connections ......……………………………………………..……...
Drawbar …………………......………………………………………...…….…
55
Chassis ….…………………………………………………………….………..
56
Tires ……………………………………………………….……..……………. 57-58
59
Mechanical Drives ………………......………………………..………………
…………………....……………………………..…………..….
60
Belt Drives …………………………………………………..………………….
61
Lubrication …………………………………………………..……………….…
62
Chain Drives
Hydraulic System …………………………………………..…………...…..… 63-64
65
Electrical System ………………………………………….………………...…
Machine Parts Breakdown ………………………………….………………………..
66
Introduction
Welcome to the SPUDNIK line of potato handling equipment. We appreciate your decision to make our
equipment a part of your operation, and look forward to a long term partnership. We strive to put the
best quality and workmanship into each of our machines, and hope as you use you’re MODEL 5640
HARVESTER, that you will find this to be true. This owner’s/operators manual has been prepared to aid
you in the safe operation and service of your windrower.
Read this manual carefully to learn how to operate your machine safely and within the designed limits of
this machine. Failure to do so could result in personal injury and/or damage to the machine
This manual is considered to be an important part of this machine and should accompany it when
moved from location to location
Warranty is provided as, part of the SPUDNIK EQUIPMENT COMPANY LLC service program, for
customers who operate and maintain their equipment as outlined in this manual.
OWNER REGISTRATION
Name
Address
City
State / Province
Country
Model Number
Serial Number
Purchase Date
5
Foreword to the Operating Manual
This operating manual is intended to familiarize the user with the 5640 Harvester and its designated
use.
This operating manual contains important information on how to operate the machine safely, properly
and efficiently. Observing the instructions in this manual help to avoid dangers, reduce repair costs/
down-time, and to increase the reliability and service life of the machine. Please take note of the section
“Dangers, operating errors and exceptions form liability”.
This Manual is to be supplemented by the respective national rules and regulations concerning accident
prevention and environmental protection.
The operating manual must always be available whenever the machine is in use.
This operating manual must be read and applied by all persons involved with the machine, such as:

Operation, including setting up, troubleshooting during operations, care, disposal of fuels and
consumables

Maintenance, including servicing, inspection, repair

Transport, including loading/unloading onto transport vehicle and standard operating travel
In addition to this operating manual and the relevant mandatory rules and regulations concerning
accident prevention and environmental protection of the country or region in which the machine is being
used, the generally recognized technical rules for safe and proper working must also be observed.
6
Limited Warranty Policy for New Spudnik Machinery
Spudnik Equipment Company LLC (“Spudnik”) warrants to the original purchaser of each new Spudnik machine to be free from
defects in material and workmanship. Spudnik will repair or replace, at its option, any part covered by this warranty that is
found to be defective during the warranty period outlined below. Warranty service must be performed by an authorized dealer
or representative of Spudnik. This warranty is applicable only for the normal service life expectancy of the product or components, as noted in the following table. Once the warranty period has begun, it cannot be stopped or interrupted.
What is included in the Spudnik Warranty:
Product
Rollers, Sprockets, Roller Chain, Belt Lacing, and Bearings
All paint to include: Insufficient coverage, failure of paint adherence,
and excessive runs. NOTE: Excessive runs not to exceed more than
15% of the painted surface on the machine.
All other materials and workmanship (except as noted below)
Genuine Spudnik replacement parts and components
Warranty Term
180 Days from 1st day of operation or 720 Hours
of machine operation, whichever comes first
12 Months from date of delivery of new Spudnik
product to the original retail customer
12 Months from date of delivery of new Spudnik
product to the original retail customer
30 days from date of purchase, or the remainder
of the original equipment warranty period,
whichever is longer
Those items that are excluded from this warranty are as follows:
(1) any merchandise or components thereof, which, in the opinion of the company have been subject to: (a) Rock chip damage and other abuse to painted surfaces, (b) damage caused by weather (to include UV damage), accident, or acts of God,
(c) any product that has been altered or modified in ways not approved by Spudnik Equipment Company LLC., (d) depreciation or damage caused by normal wear, lack of reasonable and proper maintenance, misuse, failure to follow the product’s
Operator Manual recommendations, (e) Using machine for other than normal moving of agricultural products during planting,
harvest, and processing seasons. Agricultural products to include: Potatoes, beets, onions, carrots, grains, etc., (2) Used
products, (3) Repairs made by unauthorized dealers.
To Obtain Warranty Service
To be eligible for the Spudnik warranty, purchaser must: (a) Have already remitted payment in full (b) have filled out and submitted the Spudnik Delivery Declaration form to a Spudnik representative (c) report the product defect to an authorized dealer or Spudnik sales representative and request repair within 30 days of noticing the defect and (d) make the product available to the dealer or service center within a reasonable period of time, transportation charges prepaid.
The selling dealer has no authority to make any representation or promise on behalf of Spudnik, or to modify the terms or limitations of this warranty in any way.
Limited Warranty Statement
To the extent permitted by law, Spudnik does not make any warranty, representation, or promises express or implied as to the
quality, performance, or freedom from defect of any Spudnik New Machinery. NO IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS IS MADE. IN NO EVENT WILL SPUDNIK, AN AUTHORIZED SPUDNIK DEALER, OR ANY COMPANY AFFILIATED WITH SPUDNIK BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. This warranty is subject to any existing conditions of supply which may directly affect our ability to obtain materials or manufacture replacement
parts. Spudnik reserves the right to make improvements in design or changes in specifications at any time, without incurring
any obligation to owners of units previously sold. No one is authorized to alter, modify or enlarge this warranty nor the exclusion, limitations and reservations.
To obtain more information, please contact your dealer or Spudnik at 1-208-785-0480.
7
General
Designated use of the machine:
The 5640 potato harvester is designed exclusively for normal agricultural operations (designated use).
Using the machine for other purposes or exceeding its designated limits shall be considered as being
contrary to the designated use. The manufacturer shall not be liable for any damages caused as a result
of such use. The user shall be solely responsible for such risks.
Operating the machine in accordance with its designated use also includes observing the instructions
specified in the operating manual and complying with the inspection and maintenance directives.
The potato harvester may only be operated, serviced and repaired by persons who are familiar with the
harvester and have been informed of the possible dangers.
In order to prevent dangerous situations. The information contained in this operation manual must be
read and observed by all persons who operate, service, or check this machine. Particular attention
should be paid to the section entitled “Safety”. And instructions which are not understood must be clarified before initial operation of the machine. In such cases, please consult your SPUDNIK agent or contact us directly.
The relevant accident prevention directives as well as other, generally applicable safely, health and road
traffic regulations are to be observed.
Unauthorized modification and the use of spare parts, accessories, and ancillary equipment not supplied
and/or not approved by SPUDNIK, as manufacturer, can have detrimental effects on the construction of
the machine or on the functions and hence impair the machine’s active and/or passive driving and
operations safety (accident prevention). The manufacturer does not accept liability for any damage
resulting from this.
Technical data, dimensions and weights are not binding, we reserve the right to make modification in the
course of further engineering developments; errors excepted.
Front, rear, right and left are always as seen in the direction of travel.
8
Product Characteristics
Manufacturer’s address
SPUDNIK EQUIPMENT COMPANY LLC
584 W 100 N
PO Box 1045
Blackfoot, ID 83221
Phone: (208) 785-0480
Fax:
(208) 785-1497
www.spudnik.com
E-mail: [email protected]
Advice concerning inquiries and orders
Please quite the type designation and the machine number when ordering accessories and
spare parts.
The use of spare parts supplied by third parties shall only be permitted after consultation with
the manufacture. Original spare parts and accessories approved by the manufacturer are a
contribution to safety. The use of other parts may invalidate the liability of the manufacturer for
any consequences arising out of such use.
Type Plate on machine
Machine serial number
The machine serial no. is punched into
a plate on the frame.
The entire designation has the status of a legal document and may not be
removed, changed or rendered illegible!
9
Dangers, operating errors and exemption from liability
1. No responsibility will be accepted for possible dangers arising from operating the machine in a way
which does not comply with its designated use.
2. Damage to agricultural produce particularly vulnerable to damage during processing cannot be
entirely ruled out. Weather conditions, quality of the produce and many other circumstance beyond
our or the operator’s control have an influence on the vulnerability to damage the produce being processed. For example, when processing the submerged weight, the manuring (nitrogen content), the
degree of maturity (firmness of the skin), the temperatures during processing and many other circumstances can have an influence on the vulnerability to damage. The examples do not claim to be
exhaustive.
3. To avoid damage to agricultural produce the user must adapt the machine to the respective
operating conditions. The results produced by the machine must be constantly monitored and
checked.
4. SPUDNIK shall not be liable for any damage to agricultural produce and other items which occurs as
a result of operating and adjustment errors or others incorrect usage.
5. SPUDNIK accepts no liability for any damage caused as a result of operators not complying with the
designate use of the machine. This also applies to damage to agricultural produce which, because
of certain external influences, cannot be avoided with the current state of the art.
10
Safety
This operating manual contains basic directions which should be observed during setting-up, operation and maintenance.
Therefore, this operating manual absolutely must be read by the personnel concerned prior to starting up and using the
machine, and must be available for them at all times. Any instructions which are not understood must be clarified before
initial operation of the machine, for clarification, please consult your SUPDNIK agent or contact us directly.
All safety instructions must be observed, both the general safety instructions given here and the specific safety instructions
given elsewhere in this manual.
Observe the advice contained in the operating manual as well as the generally applicable safety and accident prevention
regulations!
If safety instructions are not complied with, you risk injury to yourself and others as well as damage to the environment or
the machine. Non-compliance with safety instructions can also void claims for damages.
Identification of important instructions in the operating manual
Text marked with this symbol alerts you to possible accident and injury hazards; hazards to machinery;
practical applications, settings or functions; or environmental protection measures.
Qualification and training of personnel
Any work on or with the machine may only be performed by reliable personnel. Statutory minimum age limits must be
observed.
Employ only trained or instructed staff; the individual responsibilities of the personnel for operation setting-up, maintenance
and repair must be clearly established.
Make sure that only authorized personnel work on or with the machine.
Define the machine operator’s responsibilities — also with regard to observing traffic regulation. The operator must have
the authority to refuse any instructions issued by third parties which contravene safety!
Persons requiring training or instruction and those in a general training course, should not be allowed to work on with the
machine unless they are under the constant supervision of and experienced person.
Work on the machine’s electrical system may only be carried out by an electrical or by persons working under the
supervision and guidance of an electrician; all such work must be carried out in accordance with electrical engineering regulations.
Work on the wheels, braking and steering systems may only be performed by specially trained personnel.
Work on the hydraulic system may only be carried out by personnel with special knowledge and experience of hydraulics.
The use of spare parts, accessories and auxiliary equipment not supplied and/or not approved by SPUDNIK can have
detrimental effect on the construction of the SPUDNIK machine or on its functions and hence impair the active and/or
passive driven and/or operational safety (accident prevention).
SPUDNIK shall not be liable for any damage cause by the use of parts, accessories and ancillary equipment not supplied
and/or approved by SPUDNIK.
Conversions of or modifications to the machine may only be carried out after consultation with SPUDNIK.
11
General safety and accident prevention regulations
The safety advice and information given in this operating manual, the valid nation regulations concerning
accident prevention and any applicable internal em0playment, operational and safety regulations of the
operator are to be observed.
1. Warning signs and other notices on the machine provide important information for safe operation.
Observing them will serve your safety.
2. Before starting work, make yourself familiar with all the equipment and controls as well as their
functions. To do so when you have already started work is too late!
3. The user should wear close-fitting clothing. Avoid loose-fitting clothing!
4. Keep the machine clean to avoid the risk of fire!
5. Check around the machine before moving off or starting up (watch out for children)! Make sure you
have adequate all-around visibility.
6. Always match your speed to the local conditions! Avoid sudden turning maneuvers when driving
uphill or downhill or when traveling across a slope!
7. Observe the respective regulations when using public roads!
8. Take into account the wide overhand and/or the sideways force acting on the machine when turning
or negotiation curves!
9. Only start up the machine when all guards are attached and in their correct (protective) position!
10. Stay clear of the turning and pivoting areas of the machine!
Non-observance of the safety and accident prevention regulations entails the following risks:
-Endangering the operator or other nearby persons as a result of safety devices not being fitted or being
in their correct (protective) position!
-Damaging important machine functions!
-Errors when carrying out maintenance or repair work!
-Endangering the operator or other nearby persons through certain mechanical or chemical peculiarities!
-Risk of pollution due to leak in the hydraulic system, fuel tank, pipes, as well as in the engine and
gearbox!
12
Special safety instructions
Towed machines
1. Risk of injury hitching up or unhitching machine to/from the tractor!
2. Never allow persons to stand between the tractor and the machine unless the tractor is secured
against rolling away by means of the parking brake and/or wheel chocks!
3. Hitch up the machine only in accordance with the instructions and only to the prescribed
components! Follow the instruction in the tractor’s manual.
4. Beware of dangerous points (risk of injury through crushing and shearing) when operating the
support foot!
5. Never exceed the permissible nose weight of the machine coupling!
6. Never exceed the permissible axle loads and total weight of the tractor (see vehicle documents)!
7. During transport, secure all moving parts with the retainers provided to prevent moment and hence
possible accidents!
8. It is forbidden to allow persons to ride on the machine while traveling on roads!
9. Driving, steering and braking ability!
10. Before leaving the tractor, switch off the engine, remove the ignition key and secure the machine
against rolling away. Use wheel chocks!
11. The design and function of intake and discharge mechanisms, e.g. webs, sifting units, chutes,
means that they cannot be fully protected. Therefore, keep a safe distance from such moving parts
when in operation! This advice applies to all other similar auxiliary equipment!
12. Keep clear of discharge area!
13. Never stand or work beneath suspended loads! Persons are only allowed to stand or work under
suspended machines or machine parts (e.g. car elevator, discharge conveyor belt) when safety
supports are fitted (e.g. trestle, crane). This particularly applies to maintenance and repair work.
14. Dangerous implements are located behind safety covers. These do not necessarily come to a
standstill as soon as the drive is switch off. Therefore, keep well clear until such parts have come to
a standstill! Never open safety devices such as covers, flaps, etc. while the machine is in operation!
Never reach under safety devices!
15. Only carry out maintenance, repair and cleaning work on the machine when the drive is switched off
and the engine is stationary! Remove the ignition key from the tractor.
16. Wear suitable protective clothing, gloves, footwear, etc. when handling sharp machines, e.g. cutting
knives.
17. Keep clear of opening/hinged covers and guards!
18. Only start up the machine when all safety devices are attached and in the correct (protective)
position! It is forbidden to open or remove safety devices (e.g. covers, flaps, etc.) on the machine
while it is in operation!
19. Persons are not allowed to be on the machine while it is operation!
13
Using a power take-off (PTO) shaft
Observe the operating instruction of the PTO shaft manufacturer! An operator’s manual is supplied with
every PTO shaft.
Only use the PTO shafts specified by the manufacturer!
PTO shaft housing and guard cone as well as PTO shaft guard must be fitted and in a proper condition.
For PTO shafts, make sure the tube overlaps by the given amount in both transport and working
positions.
Only attach and remove the PTO shaft when it is disengaged, with the engine switched off and the
ignition key removed!
When using PTO shafts with overload or freewheel couplings which are not covered by the guard on the
towing vehicle, fit the overload or freewheel coupling on the machine side!
Always make sure that the PTO shaft is correctly mounted and secured.
Attach the chain to prevent the PTO shaft guard from turning!
Before engaging the PTO shaft, ensure that the selected speed and direction of rotation of the towing
vehicle’s PTO shaft agree with the permissible speed and direction of rotation of the machine!
Before engaging the PTO shaft, make sure that no persons are within the danger area of the machine!
Electrical system, electronics
Use only original fuses with the specified current rating! Switch off the machine immediately if a fault
occurs in the electrical power supply.
Work on the electrical system or equipment may only be carried by an electrician, or by specially
instructed personnel under the control and supervision of an electrician, and in accordance with the
applicable electrical engineering regulations.
The machine’s electrical equipment is to be inspected and tested at regular intervals. Defects such as
loose connection or scorched cables must be rectified immediately.
The machine is fitted with electronic components and modules, the function of which may be influenced
by the electromagnetic fields of other equipment. Such interference can lead to potentially dangerous
situations if the following safety advice is not observed.
If electrical or electronic devices and/or components are retrofitted to the machine then it is the
responsibility of the user to check whether such installations interfere with the vehicle's electronics or
other components.
This particularly applies to:
-Mobile telephones,
-Radio equipment.
In particular, the following conditions must also be satisfied if mobile communications systems (e.g.
radio, telephone are to be installed subsequently:
-Only approved devices complying with the relevant national regulations may be installed.
-The device(s) must form a permanents installation.
-The operation of portable or mobile devices in the tractor or on the machine is only permitted via a connection a permanent external aerial.
-The transmitter part must be installed separately from the vehicle electronics.
-A properly installed aerial is to be fitted with good earth connection between aerial and vehicle chassis.
The installation instructions of the machine manufacturer are also to be observed for the siring and fitting
as well as the maximum current consumption.
14
Operator's Manual MODEL 5640
Hydraulic system
1. The hydraulic system is under high pressure!
2. Make sure that the hydraulic system is depressurized (tractor and machine) when connecting the
hydraulic hoses to the tractor’s hydraulic system.
3. Hydraulic hose lines should be inspected at regular intervals and replace if damaged or worn! New
hose lines must comply with the technical specification of the machine manufacturer! Hoes and hose
couplings undergo a natural ageing process, even if stored and used correctly; therefore, their
period of storage and use is limited. The service life of a hose may deviate from these figures if
experience has shown this to be the case, in particular taking into account the potential danger.
4. Fluids escaping under high pressure (hydraulic oil) can penetrate the skin and cause serious
injuries! If such injuries occur, call a doctor immediately! Risk of infection!
5. Lower the machine, depressurized the system and switch off the engine before working on the
hydraulic system!
6. Take care when working on the hydraulic system. Hot hydraulic oil can cause serious burns! Let the
hydraulic system cool down beforehand and wear gloves! Collect and dispose of old oil in
accordance with the regulations!
15
Operator's Manual MODEL 5640
Warning symbols and other instruction notices on the machine
SIGNAL WORDS:
DANGER, WARNING, and CAUTION are signal words with messages:
DANGER: An immediate and specific hazard, which WILL result in server injury or death if
proper precautions are not taken.
WARNING: A specific hazard or unsafe practice, which COULD result in server injury or
death.
CAUTION: Unsafe practices, which COULD result in personal injury if proper precautions
are not taken.
MOVING DRIVES Can cause
severe injury.
Shut off power before
removing shields.
EXPOSED DRIVE Can cause
severe injury.
Keep all shields in place while
machine is running.
MOVING MACHINERY
Can cause severe injury
or death.
Do not mount or dismount
moving machine.
LOW SPEED TIRE Can cause
severe injury or machine
damage.
Do not exceed 20 mph
16
Operator's Manual MODEL 5640
Warning symbols and other instruction notices on the machine
FLYING OBJECTS Can cause
severe injury .
Keep clear of fan discharge at
all times.
ROTATING DRIVELINES Can
cause severe injury or death.
Keep all driveline shields in
place. Securely attach both
ends of driveline.
ROTATING DRIVELINES Can
cause severe injury or death.
Keep all driveline shields in
place. Securely attach both
ends of driveline
17
Operator's Manual MODEL 5640
Warning symbols and other instruction notices on the machine
SLIPPERY SURFACES Can
cause injury.
Be careful when mounting and
dismounting.
HEAVY TONGUE WEIGHT Can
cause severe injury or death.
Support jack and tongue securely.
Min. jack rating 10,000 lbs.
HIGH PRESSURE OIL Can cause severe
injury or death.
Do not go near leaks.
Relieve hydraulic pressure before loosening fittings. If injured, seek immediate
emergency medical help.
ADMA
Safety manual
18
Operator's Manual MODEL 5640
Configuration and functions of the machine
Operation of the machine
The SPUDNIK harvester is designed for harvesting potatoes and vegetables.
The towing vehicle runs along the side of the potato ridges when digging.
The potato ridge is dug depending on the configuration of the intake
The harvested produce can be separated from trash such as soil, vine and stones with the help of
various subassemblies.
The potatoes are temporarily stored in the moving-floor bunker until they can be transferred to a
transport vehicle.
This chapter describes the configurations and function of the individual subassemblies.
19
Operator's Manual MODEL 5640
Configuration and functions of the machine
Harvester Tractor Connection
Hitch to tractor
Driveline to PTO
Note: Take PTO off of tractor to turn manually
20
Operator's Manual MODEL 5640
Configuration and functions of the machine
Harvester Tractor Connection
Hydraulic hoses to hydraulic ports
six hoses to ports on tractor
Power plug to tractor
CCI terminal and plug
Control box plug
21
Operator's Manual MODEL 5640
Configuration and functions of the machine
Camera systems
Camera connections
Camera magnet
Camera
Screen-Panel and mount
Wire between camera and
MULTIPLEXER
Power wire for MULTIPLEXER
Use RED/WHITE for POSITIVE
Wire between Screen and
MULTIPLEXER
22
Black for NEGATIVE on a 12 V plug
MULTIPLEXER
Operator's Manual MODEL 5640
Configuration and functions of the machine
Camera systems
Camera 3
Screen plug
Camera 2
Camera 1
Power plug
MULTIPLEXER
Screen-Panel
ON/OFF
Scroll between A & B
Lighter or darker
Contrast, tint,
volume, & menu
Adjustment
23
Operator's Manual MODEL 5640
Configuration and functions of the machine
Control Panel
Self Hydraulic Speed Control: A PWM Signal
which can be adjusted over the Speed Button is
provided for the East Coast Hydraulic Setup.
(option shaker speed control.)
Swing boom
switch here
The Signal can be turned on/off with the on/off
Button. This Option does not need to be
configurable.
L. Level: When in use with the harvester, the
left level controls the level on the back of the
harvester up or down on the left side.
R. Level: When in use with harvester, the right
level controls the level on the back of the
harvester up or down on the right side.
Auto Dig UP: This button must be held for a least 1/2 second to start the function. (option: this brings left and
right coulters up (3 seconds).) then the digger nose will come up (this takes an additional 4 seconds) Hydraulic
shaker will stop (option).
To stop auto dig UP any of the following rocker buttons will stop this command. Digger Up or DOWN, l. Coulter
UP or DOWN.
Auto Dig DOWN: This button must be held for at least 1/2 second to start the function. (Option: This brings the
digger nose down (3 seconds).) The digger nose is put in float and the float light goes on. Then the coulters will
go down (this takes an additional 4 seconds). Ridge relief starts after 15s. (Option) To stop auto dig DOWN any
of the following rocker buttons will strip this command: Digger Up or DOWN, L. Coulter, R. Coulter UP or
DOWN. Hydraulic shaker will start (option).
Digger Up and Down, L. Coulter, R. Coulter.
Tapping the digger UP will remove float and make the hydraulics lock again.
The float feature allows the windrower or harvester to safely be pushed up by rocks or whatever it may
encounter while in use and then to float back to it’s original position after collision.
Red Center Light: For use with the return to center bracket only. This light turns on when the steering wheels
have returned to the center and straight position . If LEFT or RIGHT steering rocker is used, the light will turn
off.
Auto Rocker/Rotary Shaker Shut Off: This Option has to be configured. Auto Dig DN energizes Valve Y32.
Y32 opens and oil flows to Hydraulic Motors. Auto Dig Up closes the valve again. With the Shaker UP/DN Button the Shaker can be shut on/off manually during operation. If the Shaker has been shut off previously to the
Auto Dig UP/DN Cycle the Shaker will come back on. If Auto Depth is used it will turn on the Shaker with Auto
Dig DN and Off with Auto Dig up.
For CCI control panel instructions please see CCI instruction manual
24
Operator's Manual MODEL 5640
Configuration and functions of the machine
Control Panel
Support Wheel LH + RH: This is used
for the lowering and raising of the
support wheels when Terra Float drum
(option)
Swing boom
switch here
Shaker: This button raises and lowers
the mechanical shaker. (Option: speed
& shaker on/off will increase/decrease
shaker speed.)
Steering: This rocker switch steers the
rear wheels left or right.
Center: Return to Center control; this returns the rear wheels (with purchase return to center installed)
to their center position from the left or right steering position.
Digger: This rocker switch raises and lowers the digger nose UP and DOWN manually when the digger
is not in float.
Fold Out Boom: Tip it back for down, forward for up. The boom chain stops when you push the button
for safety. The outer boom needs to be fully extended before moving fold out boom.
For CCI control panel instructions please see CCI instruction manual
25
Operator's Manual MODEL 5640
Configuration and functions of the machine
Control Panel
Red Float Light: This light turns on
after the digger DOWN has been
pushed for 1.5 seconds; this light
signals the digger nose is in float
position (not locked hydraulically). It
will flash when in ridge relief.
Swing boom
switch here
L. coulter: This rocker switch raises
and lowers the left coulter UP and
DOWN.
R. coulter: This rocker switch raises
and lowers the right coulter UP and
DOWN.
Buzzer: This allows the user to know if the cross conveyor is moving to slowly and can be turned on or
off with the push of the buzzer button. The buzzer will automatically reset to the on position when power
is removed from the box.
Red Alarm Light: The cross conveyor is monitored from this light. This light will turn on and remain on
when the speed of the cross conveyor is too slow. An associated buzzer will sound along with the light
to alert the user to a potential problem. A potential problem could be the conveyor belt becoming
jammed or the PTO slowing down.
OK Light: This light should always be on when the control box is switched on.
JOYSTICK: The joystick controls the “inner”boom in the Up or Down position as well as the “outer”boom
UP or DOWN position.
Teach in Speed Sensors with Auto Reset: Standard is one Speed Sensor for the Rear Cross. The
min. allowable speed is teachable. Slow the machine down until the min. allowable speed is reached.
Hold the Buzzer Button for 5 sec. The Buzzer will beep for 20ms when the new value is stored. If the
Speed drops below the stored value, the Buzzer will go on.
The Buzzer can be switched off by pressing the Alarm Button (End of Field). If the Rear Cross resumes
back to speed, the Buzzer automatically becomes enabled again. The Alarm Light will remain on when
the speed is too low. This Option has to be configured. Two additional Speed Sensor Inputs are
available. They have to be configured (enabled). It is necessary to go through the Teach in Process
again. If one out of the 2/3 Sensors defects a low speed the Buzzer and Alarm light will come on.
For CCI control panel instructions please see CCI instruction manual
26
Operator's Manual MODEL 5640
Configuration and functions of the machine
Control Panel
Swing boom
switch here
Auto Depth Setting
This Option has to be configured.
1.) Desired Depth Setting
-The desired depth is determined by adjusting the sensor on the digger depth indicator. The
Sensor looks for the edge inside the bracket. The desired depth should be adjustment manually during
digging, then adjust the sensor to the edge inside the bracket.
-The max. Sensor working distance is about 1/8” (Distance between sensor and edge).
2.) Go to the desired depth
-The Auto Dig down button will bring the Digger to the adjusted depth. If the sensor sees the
edge, the float will flash slow.
3.) Overwrite the depth
-With the Digger up/down button the depth can be overwritten. The float light will stop flashing.
Pressing the Auto Dig down button the Digger will return to adjusted depth.
-By holding the Digger down button for longer than 1.5sec the Digger nose will go into float.
-The max. Depth should be adjusted with the chain length.
4.) Auto Dig Up
-The Auto Dig up button will lift the coulters first and then the Digger nose. See Auto Dig up/
down.
5.) Auto Dig Down
-If the Auto Dig Up Button was used in advance, Coulters and Digger nose will go down based
on the timing. If the Auto Dig up has not been used in advance, only the Digger will go to the desired
depth. The Coulters are not moving if the Auto Dig Up Button has not been used before.
For CCI control panel instructions please see CCI instruction manual
27
Operator's Manual MODEL 5640
Configuration and functions of the machine
Electrical
1.
RCM X-conveyor
2.
Return to center
3.
ADS auto depth
4.
Elevator max height
5.
Not in use
6.
Ultrasonic sensor DN
7.
Ultrasonic sensor UP
8.
Not in use
9.
Buffer belt sensor
10. Infra red sensor
Hour Meter
Note: fuses for two working lights are
the two green wire fuses on the left.
The red wire fuse on the right is for
the computer board.
28
Operator's Manual MODEL 5640
Configuration and functions of the machine
Pre Dig Test

Bring tractor up to RPM’s

Test hydraulic functions
-Coulter up and down
-Steering
-Wheel leveling
-Hydraulic shaker
-Boom lift
-Boom chain drive
-Digger up and down

Test chain drives, engage PTO

Test sensors
-Drive sensors
Turn off drives and buzzer should come on, if not adjust sensor up
and down or side to side.
Note: Distance between sensor and
star should be 1/8”
29
Operator's Manual MODEL 5640
Configuration and functions of the machine
Pre Dig Test
(continued)

Return to center
-Wheels should center themselves, if not calibrate sensor with the following instructions
Calibration instruction
1.) Position wheels as need for set position
2.) Push and release SET (“CAMERA”) button
3.) Push and release “CENTER” button
After finishing the above sequence the wheels will now be set as the place the wheels will return to
each time the “CENTER” button is pushed.
30
Operator's Manual MODEL 5640
Configuration and functions of the machine
Field Dig Test
(continued)
Conditions:
Use steep angle for heavy stone less soil conditions.
Use shallow angle for light rocky soil conditions.
Blade angle
Based on conditions and soil type the blade angle will need to be adjusted in order to pull the
harvester through the field in the best way to achieve max speed with desired flow and
penetration
If you change the hitch to the top or bottom you have to change the limiter chains to maintain
same digging depth!
The blade can be adjusted by the following:
Drawbar adjustment—
Moving the hitch up decreases the blade angle
Moving the hitch down increases the blade angle
Heavy duty pulling rings like the one shown
have different inserts depending on what
size draw pin is being used
Blade adjustment—
Pivoting the blade down decreases the angel
Pivoting the blade up increases the angel
31
Operator's Manual MODEL 5640
Configuration and functions of the machine
Field Dig Test
(continued)
Setting draw angle for digger nose
Standard angle
Flat angle: use this in heavy
conditions when the ground
is so hard, that the digger
nose won’t get into it
Steep angle: use this in
conditions with many
rocks, that the digger can
easily get above them.
32
Operator's Manual MODEL 5640
Configuration and functions of the machine
Field Dig Test

Check depth
-Too deep, adjust the following:
Screw out gage wheels to lift nose.
Move limiter chain up one link.
-Too shallow, adjust the following:
Screw in gage wheels to lower nose.
Move limiter chain down on link.

Side to side level
-One side too deep, adjust the following:
Adjust side chain (side carrying most dirt) up one link or adjust hydraulic lift on
pivot axle (side carrying most dirt) up.
Note: The dirt and product flow on digger should be uniform across the whole digger.
Limiter chain
Note: Try to have dirt on the chains until the
end of the secondary chain. This will
minimize bruising on the potatoes.
33
Operator's Manual MODEL 5640
Configuration and functions of the machine
Field Dig Test
(continued)
Belted chain speeds
Depending on yields and field conditions the belted chains may need to be sped up or slowed
down, to keep flow uniform on belted chain the following shows what sprockets to change for
each belted chain.
-Primary chain
Note: Increasing the sprocket one more tooth
will cause primary chain to move 7% faster
(inside sprocket)
Note: Try to speed up each chain faster than the previous chain until the end of the machine.
Note: Changing the sprocket changes the speeds of all the chains and rollers on the harvester
except the boom
Secondary chain (outside sprocket Right Hand side)
Same as above
Rear cross chain and transfer rolls only sprocket located under shield at the back of
harvester on left side.
34
Operator's Manual MODEL 5640
Configuration and functions of the machine
Field Dig Test
(continued)
Side elevator and eliminator rolls sprocket located on three way gear box
-Eliminator only
Sprocket located on side elevator drive shaft under shield on left side
35
Operator's Manual MODEL 5640
Configuration and functions of the machine
Field Dig Test
(continued)
-Boom
Controlled by tractor hydraulics
-Diviner
Same as primary and secondary
Or sprocket located under shield on right rear side
Note: Increasing the sprocket one
more tooth will cause secondary
and vine chain to move 7% faster.
-Rear cross angle adjustment
Rear cross may need to be angled steeper or flatter depending on yields and conditions to
achieve even potato distribution. The following shows the points to do adjustments.
Note: The product flow needs to be evenly spread out on the entire
rear cross chain.
If not, there are problems with the vine separation.
36
Operator's Manual MODEL 5640
Configuration and functions of the machine
Field Dig Test
(continued)
-Side elevator angle adjustment
Side elevator may need to be angled steeper or flatter depending on yields and conditions to
achieve even potato distribution. The following shows the adjustment.
Note: The product flow needs to be evenly spread out on the entire
elevator to achieve the best separation on the roller star table.
-Hopper adjustment
37
Operator's Manual MODEL 5640
Configuration and functions of the machine
Field Dig Test
(continued)
-Cleaning table adjustment
Finger roll table
 The spacing for the finger rolls is done by turning the adjustment bolts right or left
depending on the gap that is desired for optimum separation and elimination.
38
Operator's Manual MODEL 5640
Configuration and functions of the machine
Field Dig Test
(continued)
Shakers
Adjusted as needed hydraulically from cab using tractor hydraulics
Too much dirt to secondary » increase shake or slow down
Not enough dirt » decrease shaker or speed up
Depending on the conditions, you can also
change the amplitude of the shaker.
Top hole: least shake (bruise less)
Bottom hole: most shake (more effective, more
bruising)
Slip clutches
Set based on field conditions. The bolts must all be turned down equally to insure
proper friction on the face of the sprocket
39
Operator's Manual MODEL 5640
Notes !!
40
Operator's Manual MODEL 5640
Harvester Trouble Shooting
Problems
Hydraulically controlled
components creep.
Hydraulic cylinders do
not hole set position.
Hyd.
Possible cause
Remedy
Leaking hydraulic hoses.
Replace or repair hose.
Hydraulic fitting leaking.
Check fitting and tighten if
lose.
Hydraulic cylinders leaking.
Tighten packing nuts on end
of cylinder. If still Leaks,
repair cylinder.
Machine does not
respond to operation
Control Box.
Leakage around spools
control valve or spool
openings are plugged.
Clean spools.
Broken hydraulic hose.
Replace or repair hose.
Tractor Control Valve off
Turn Valve on
Hydraulic fitting leaking.
Check fitting and tighten if
loose.
Hydraulic cylinders leaking.
Check fittings and tighten if
loose.
Tighten Pack
Hyd./
Elec.
No power to control box.
Check all electrical
connections.
Filter of tractor plugged.
Change filter.
Low hydraulic oil in tractor.
Fill up tractor oil.
Hydraulic hoses not fully
plugged in.
Check hoses plugged into
tractor. Be sure they are
engaged.
Switch control box off
Leaking hydraulic hoses.
Hyd.: hydraulic problems
Harv.: harvest settings
Mech.: mechanical problems
Elec.: electrical problems
41
Operator's Manual MODEL 5640
Harvester Trouble Shooting
Problems
Slip clutches beginning
to slip.
Mech.
CAUTION: STOP
MACHINE
IMMEDIATELY
Too much soil carried
up belted chain.
Remedy
Possible cause
Foreign object in machine.
Check which clutch is
slipping.
Find and remove foreign
object. Beware of chain
tension and release if
possible.
Machine overload.
Check for excessive amount
of dirt or trash. Are all other
parts turning?
Broken part in harvester.
Check all areas of the
windrower and drive system
for malfunctioning part.
Slip clutch too loose.
Tighten slip clutch until the
unit carries the required load.
1/2 turn at a time on all slip
clutch bolts, then try again.
Excessive build-up of vines.
Clean vines from rollers,
sprockets, and chains.
Digging too deep.
Raise digger blade until it
begins to cut potatoes then
lower it slightly.
Travel speed too fast for
speed of belted chain.
Harv.
42
REMEMBER: To cause
less bruise, solid needs
to be carried to the end
of the side elevator.
Slow travel speed or increase
speed of chains. (Change hex
sprockets or increase tractor
RPM)
Adjust optional shaker.
(increase RPM of shaker
Not enough agitation.
hydraulically or increase
amplitude mechanically)
Wrong type of digger blade.
Change type of blade,
depending on set of
the potatoes.
Belted chain pitch too narrow.
Change belted chain to wide
belted chain.
Hyd.: hydraulic problems
Harv.: harvest settings
Mech.: mechanical problems
Elec.: electrical problems
Operator's Manual MODEL 5640
Harvester Trouble Shooting
Problems
Remedy
Possible cause
Field conditions too dry.
Irrigate field or wait if
possible for wetter
conditions.
Not enough agitation in
primary belted chain.
Adjusted optional shaker.
(increase RPM of shaker
hydraulically or increase
amplitude mechanically)
Optional Rollerstar too narrow
Adjust Rollerstar distance
Digging too deep.
Raise digger blade until it
begins to cut potatoes then
lower it slightly.
Override belted chain pitch
too wide.
Use narrow pitch override
belted chain.
Vegetation removed before
harvest.
Do not chop vines.
Grass clumps and roots not
being removed by deviner
chain
Try to eliminate them with the
optional Rollerstar
Vines are down the deviner
chain before the blower
Speed up PTO.
Machine running too slow.
Speed up PTO.
Note enough tilt on rear cross
conveyor and side elevator.
Increase the angle
Individual conveyors too fast
or too slow.
Change drive sprockets.
Clod not being removed.
Harv.
Harv.
Harv.
Trash and vines not
removed by diviner
chain.
Material flow not in
correct position on
conveyors and on
Rollerstar.
Hyd.: hydraulic problems
Harv.: harvest settings
Mech.: mechanical problems
Elec.: electrical problems
43
Operator's Manual MODEL 5640
Maintenance
General safety instructions
Regular maintenance is a prerequisite for operational reliability. The following safety
advice is to be observed during any maintenance, cleaning or repairing work.
To prevent accidents, all relevant rules and regulations concerning safe and
competent working must be observed!
Observe the adjustment, maintenance and inspection activities and intervals specified in this
operating manual, including details concerning the replacement of parts, subassemblies and equipment.
These activities may only be executed by trained personnel.
Instruct operating personnel before beginning special operations and maintenance work! Delegate a
supervisor!
Always observe the relevant safety measures and instructions specified in the operating manual when
carrying work related to the operation, adaptation, conversion or adjustment of the machine as well as
maintenance, inspection and repair activities.
Ensure the working area is adequately secured during the maintenance work!
Use suitable, tested tools when working on the machine, only use proper tools for unscrewing and
tightening screwed connections. Wear gloves!
Switch off the machine completely before maintenance and repair work and ensure that it is secured
against inadvertent starting. The machine must not be switched on again while the work is being carried
out!
-Switch off operating facilities.
-In the case of tractors, self-propelled harvesting machines and engine-driven machines, switch off the
engine, remove the ignition key and, if necessary, lock the cabin. Nobody is allowed to be within reach
of the controls so that functions cannot be switched on again by accident.
-Switch off the main switch and attach a warning sign, if necessary.
-Disconnect the machine from the power supply, Depressurize the hydraulic system and compressed air
lines and disconnect them from the supply.
Carry out maintenance and repair work only when the machine is positioned on firm and level ground
and has been secured against inadvertent movement and toppling.
When replacing individual parts and larger subassemblies, they should be carefully attached to lifting
gear and secured against falling down. To avoid the risk of accidents, sharp edges, corners and
dangerous projections must be covered and a warning sign attached. Use only suitable hoisting and
lifting gear with adequate load capacity which is in a proper working condition. Never work or stand
under suspended loads!
The securing of loads and the instruction of crane operators should only be entrusted to experienced
persons. A signaler giving instructions must be within sight of the crane operator and must be provide
with a radio link.
Only carry out overhead assembly work using suitable ladders and platforms. Never climb on the
machine itself! Wear a safety harness when carrying out maintenance work at greater heights.
Keep all handles, steps, handrails, platforms, landings and ladders free from dirt, snow, and ice.
44
Operator's Manual MODEL 5640
Maintenance
Clean the machine, especially connections and threaded unions of any traces of oil, fuel or
preservatives before carrying out maintenance/repairs. Never use aggressive detergents. Use lint-free
cleaning cloths.
Before cleaning the machine with water or steam jets (high-pressure cleaners) or other cleaning
agents, cover or tape all openings which—for safety and operational reasons—must be protected
against ingress of water, steam or leaning agents. Special care must be taken with electric motors and
switching cabinets, as well as all additional electrical or electronic components, after cleaning, remove
all covers and tape completely.
After cleaning, examine all fuel, lubricant and hydraulic oil lines for leaks, loose connections, scuffing
marks and damage. Any defects found must be rectified without delay.
Immediately retighten any screwed connections that have been unscrewed during maintenance and
repairs.
Any safety devices removed for setting-up, maintenance or repair purposes must be refitted and
checked immediately upon completion of the maintenance and repair work.
Ensure that all fuels, consumables and replaced parts are disposed of safely and with minimum
environmental impact.
Maintenance Safety Stickers
45
Operator's Manual MODEL 5640
Maintenance
Special safety instructions
Safety devices
Never stand beneath suspended loads!
Never stand or work beneath suspended loads!
Engage safety catches!
Never stand or work beneath suspended loads. The figures below show special safety
devices for supporting loads.
Adjustment and maintenance work on these parts of the machine may only be carried
out with the safety devices engaged.
46
Operator's Manual MODEL 5640
Maintenance
Spare parts procurement
Please quote the details on the type plate(s) as well as the machine’s serial no. on every order for
spare parts or accessories, or inquires of a technical nature.
The use of spare parts supplied by third parties is prohibited. Original spare parts and accessories
approved by the manufacturer are a contribution to safety and guarantee proper functioning. No
liability can be taken for consequences resulting from the use of other parts.
When replacing electrical or hydraulic parts, ensure that only original SPUDNIK spare parts are
used. The use of non-SPUDNIK parts can cause malfunctioning of the machine.
Type plate on machine
Machine serial number
The machine serial no. is punched
into a plate on the frame.
The entire designation has the status of a legal document and may not be removed,
changed or rendered illegible!
Disposing of replaced parts
The following points should be observed before replacing or disposing of parts.
-Replaced parts which still function should be cleaned and stored in an orderly manner.
-Machine parts which cannot be repaired should be only be disposed of at appropriate
collecting points or be collected by a crap metal dealer.
So called “valuable” materials should be deposed of in a proper way, i.e. plastics,
rubber, scrap metal, etc. should be recycled.
Collect and dispose of old oil in accordance with the regulations.
47
Operator's Manual MODEL 5640
Maintenance
Repairs to the electrical system may only be carried out by authorized
dealers.
Exercise extreme care when working on engine or hydraulics — risk of
serious burns!
In order to keep wear down to a minimum, clean the machine
thoroughly inside and outside. Non-observance of the instructions can
lead to malfunctions or premature wear. In this case the user carries
sole responsibility for any damage which occurs.
To ensure the operational reliability of the machine, prevent accidents
and avoid, damage, remove dirt, deposits and inflammable materials
from the machine on a daily basis!
Only carry out cleaning work when the engine is switched off!
Remove the ignition key!
Secure the machine against rolling away!
Protect the electrical system from moisture and dirt. This particularly
applies when utilizing high pressure cleaning equipment.
Cleaning after every operation
In order to deep wear down to a minimum, follow the instructions given below:
-Remove dirt, deposits and inflammable material from the machine on a daily
basis.
-Inspect the machine for damage once a week and replace defective parts
immediately.
-Take note of comply with the information regarding cleaning with highpressure cleaning equipment.
The following figure show the parts of the machine, which must be cleaned
after each use:
48
Operator's Manual MODEL 5640
Maintenance
Parts to be cleaned
-Transition between 2nd separator and
picking table
-Fingers/brushes on scraper belt.
Cleaning with high-pressure cleaning equipment
Clean the machine thoroughly, inside and outside. Dirt attracts moisture and leads to corrosion. The
following advice should be adhere to when using high-pressure cleaning equipment to wash down the
machine:
Cleaning instructions:
During the first six weeks do not wash down the machine with high-pressure cleaning equipment.
Thereafter:
-Do not direct the jet of water at bearings.
-Do not direct the cleaning jet towards electrical/electronic components.
-Only use a wide-jet nozzle; machine nozzle clearance to be min. 600mm (2ft).
-Always keep the wide-jet nozzle moving from side to side.
-Nozzle spraying angle min. 25degrees.
-Spraying pressure max. 1450 psi.
-Water temperature max. 68 degrees Fahrenheit.
-Do not use any cleaning additives.
49
Operator's Manual MODEL 5640
Maintenance
Storage
Only carry out adjustments and maintenance work when the engine is switched off!
Remove ignition key!
Secure the machine against rolling away!
Secure machine against rolling away!
Engage parking brake and use wheel blocks!
Careful storage of the machine or the spare parts avoids repair costs and downtimes. At the
same time, reliability and service life are improved.
Make a note of all maintenance work to be carried out before the next season and arrange for
this to be carried out in a good time.
Your SPUDNIK dealer is in a better position to perform maintenance work and any repairs that
may be necessary outside the season.
The instruction below should be followed at the end of the harvesting season:
Storage instructions
Clean the machine thoroughly. Dirt attracts moisture and leads to corrosion.
Store the machine in a dry place. Do not store in the vicinity of artificial
fertilizers (mineral).
Clean all drive chains thoroughly and pray them with chain spray in order to
prevent corrosion.
Storage instructions
Cleaning the machine
——
Chain drive
Smear grease on all unpainted parts, the piston rods of all hydraulic cylinders
and the threads of all spindles.
——
Check moving parts (hinges etc.) for ease of movement, dismantle if
necessary, clean and check for signs of wear.
Replace with new parts if necessary.
——
Grease the machine thoroughly.
Lubrication
Repair paint defects, protect any bare metal with a good coating to rust
inhibitor.
——
Follow the instructions for engine storage in the case of self-propelled
machines.
——
50
Operator's Manual MODEL 5640
Maintenance
Shortening/repairing the main webs
Main webs with main web connectors
Procedure for shortening or repairing main webs or (Belted
Chain) with main Belt or Web connectors:
Increased risk of injury when using cutting tools.
Wear Gloves!
Note: The Belt or Web end Link of the
belted chain is symmetrical, any link will
fit in any end ling position.
End link Looks are joined together as
shown.
Note: The Master Chain Link Rod, it has
Two notches or slots cut in the end of
the link Rod. These match the Loops in
the End Link. Push the Link Loops
together and insert the Master Chain
Link Rod. One of the End Link’s set of
Loops with set inside the notches in the
Rod. The Belt tension will hold the Rod
in position.
51
Operator's Manual MODEL 5640
Maintenance
Belt portion of Belted Chain
Note: The bet is made up of
Notches and Cams
Notch and Cam
The End Link is shaped as shown,
to fit the Notch and Cam portion of
the Belt. It also is Bent in a way to
hold a chain Link
Chain Link bent slot, Chain link sits
inside between link and belt.
Cut off belt at end of cam as
shown, make sure that the belt
end does not go past the edge of
link as shown. The belt must not
protrude in to the Loop area of
the link, as this will interfere with
the Master Link Rod.
The link is held in place with 3
Rivets, 2 in the end 3/16 x 1 &
3/16” and 1 in the center 3/16 x
7/8” long
52
Operator's Manual MODEL 5640
Maintenance
Slide End Link over Cam of Belt, with
back edge in slot
Slide End Link rod Under Belt and
between End Link, Inside bent
opening of End Link as shown on
previous page
Drill 3, 3/16” holes in Belt using
link as a guide. Insert Rivets
Long Rivets in end and shorter
one in center or middle.
Mash or Squeeze together End Link
and flatten or brad over Rivets
53
Operator's Manual MODEL 5640
Maintenance
Screwed connections
Screwed connections in general
Only carry out adjustments and maintenance work when the engine
is switched off!
Removed ignition key!
Secure the machine against rolling away!
The tightening torques given in the table below do not apply when a different torque is specified in this
manual for a particular screwed connection. Check all nets, bolts, and screws regularly for tightness.
Shear pins are designed in such a way that they sheer off at a certain load. When replacing shear
pins, make sure that only pins of the same grade are used.
When replacing nuts and blots, make sure that nut.bot parts are of the same or higher grade. Nuts,
bolts and screws of a higher grade should be tightened with the same torques the original parts being
replace make sure that threads are clean and that they engage properly. This prevents damage upon
tightening.
The tightening torques required are given in
the adjacent table.
The Strength grade is specified on the screw
head.
Screwed connections with special
maintenance requirements
Only carry out adjustments and
maintenance work when the engine
is switched off!
Remove ignition key!
Secure the machine against rolling
away.
The following screwed connections require
special maintenance. Non-compliance should
result in damage to the machine or chassis.
54
Operator's Manual MODEL 5640
Maintenance
Main web connecting pieces
All main webs and discharge conveyor belts are fitted with a connecting piece so that each web can be
easily changed.
The screws of the connecting pieces are to be checked for tightness at the following intervals:
-After the first digging operation
-After 50 operating hours
-Thereafter, every 200 operating hours.
Drawbar eye for hitch and Piton-Fix couplings
The screwed connection shown must be checked for tightness at the following intervals:
-Prior to the first use under load,
-After the first use under load,
-After 50 operating hours,
-After 100 operating hours,
-Thereafter, every 200 operating hours.
Type of bolt:
1” UNC
No. of bolt:
2
Tightening torque:
250 ft lb
55
Operator's Manual MODEL 5640
Maintenance
Chassis
Any adjustments or repairs to the chassis which are not shown
here may only be carried out by and authorized dealer.
Non-compliance with this rule invalidated the guarantee.
The adjustments shown here may only be carried out when the
engine is switched off!
Remove ignition key!
Secure machine against rolling away!
Never overload axles, brakes or chassis.
Loosen and tighten the wheel nuts in the sequence shown.
Note: Use a torque wrench to tighten the wheel nuts in the sequence
shown!
Standard axle wheel nuts
The screwed connection shown must be checked for tightness at the following intervals:
56
Operator's Manual MODEL 5640
Maintenance
Tires
Repair work to the wheels should only be carried out by an
authorized dealer.
Only work on the wheels when the engine is switched off!
Removal or tagging of ignition switch or key is advised!
Secure the machine against rolling away, block wheels!
Maintain the prescribed tire pressures and check once a week (see technical specifications).
There is a risk of bursting or explosion of the tire if the tire pressures are too high!
Stank clear and back from the tires when pumping them up.
Check tire pressures regularly.
Tires with divided or split rim: Released tire pressure before attempting repairs!
The use of a tire safety cage, to inflate after repairs is advised!
When working on the wheels, secure the machine against rolling away (block wheels)!
Never work on machine which is supported only by a jack.
Make sure that the jack has adequate load-carrying capacity.
57
Operator's Manual MODEL 5640
Maintenance
Tires
Repair work to the wheels may only be carried out by an authorized dealer.
Only work on the wheels when the engine is switched off!
Remove ignition key!
Secure the machine against rolling away!
Maintain the prescribed tire pressures and measure once a week (see technical specifications)
There is a risk of bursting if the tire pressures are too high!
Stand clear of the tires when pumping them up.
Check tire pressures regularly.
Tires with divided rim: Release tire pressure before attempting repairs!
When working on the wheels, secure the machine against rolling away (wheel chocks)!
Never work on machine which is supported only by a jack.
Make sure that the jack has adequate load-carrying capacity.
58
Operator's Manual MODEL 5640
Maintenance
Mechanical drives
Gearboxes
Only carry out adjustments and maintenance work when the engine is switched off!
Remove ignition key!
Secure the machine against rolling away!
Mount all guards correctly after completing any adjustments.
Clean gearboxes before carrying out maintenance.
Periodic maintenance:

Visual inspection for leaks.

Check level as instructed.
Maintenance at the end of the harvesting season:

Visual inspection for leaks.

Change oil as instructed.
Changing the oil:

Drain off the old oil from the gearbox through the drain plug.

Refit the drain plug after all the oil has been drained.

Fill up through the filler plug with the required quantity of new oil to the correct specification.
Level control:
Two methods of checking the level are possible for the gearboxes:
1. Checking the level by means of the over flow plug:
- remove overflow plug from gearbox.
- the oil level in the gearbox must be such that the oil just runs out of the opening.
- if the necessary, top up the oil level via the filler plug.
- refit overflow plug.
2. Checking the level by means of a dipstick:
- remove dip stick from gearbox.
- the oil level must lie between the upper and lower marks on the dipstick.
- if necessary, top up the oil level via the filler plug.
- refit dipstick.
Further details concerning oil changes are given below.
59
Operator's Manual MODEL 5640
Maintenance
Chain drives
Gearboxes
Only carry out adjustments and maintenance work when the engine is switched off!
Remove ignition key!
Secure the machine against rolling away!
Mount all guards correctly after completing any adjustments.
Periodic maintenance:

Check chain tension.

Carry out a visual inspection for damage.

Lubricate with chain spray as instructed.
Maintenance at the end of the harvesting season:

Clean all drive chains and spray them with chain spray in order to prevent corrosion.

Replace worn parts.

Check chain tension.
Check chain tension:
During the first few operation hours, check the chains frequently for the correction tension.
The sag of a chain should be equal to approx. 2% of the distance between the shafts of driving and
driven chain sprockets, measure on the side opposite the chain tensioner. The chain should not
sag at all on the side of the chain tensioner.
Example:
If the shaft spacing between driving and driven chain sprockets is equal to 250mm, then the sag if the
chain should be 5mm
Chains which are too loose cause rapid and excessive wear on the roller links and chain sprockets.
Chains which are too taut cause excessive wear on the chain, the bearings and the shafts.
All further information necessary for the carry of chain drives can be found on the following pages.
60
Operator's Manual MODEL 5640
Maintenance
Belt drives
Only carry out adjustments and maintenance work when the engine is switched off!
Remove ignition key!
Secure the machine against rolling away!
Mount all guards correctly after completing any adjustments.
Periodic maintenance:

Check belt tension.

Carry out a visual inspection for damage.
Maintenance at the end of the harvesting season:

Detention all drive belts.

Replace worn parts.
Check chain tension:
Loosen the pulleys when fitting a new belt. Never force a belt over a pulley as this will damage the
integral fibers and hence weaken the belt.
New belts stretch initially. Therefore, retention frequently during the first few days. More belts are
ruined through inadequate tension than through excessive tension!
All further information necessary for the care of belt drives is given in the following figures:
61
Operator's Manual MODEL 5640
Maintenance
Lubrication
Only carry out adjustments and maintenance work when the engine is switched off!
Remove ignition key!
Secure the machine against rolling away!
Mount all guards correctly after completing any adjustments.
Only use a good quality brand-name grease, e.g. Shell Retinaz A EP2 multipurpose grease.
Remove dirt from lubrication nipples prior to applying grease. Wipe away any excess grease escaping
from bearings.
All further information concerning the various lubrication points is given in the following figures:
62
Operator's Manual MODEL 5640
Maintenance
Hydraulic system
Only carry out adjustments and maintenance work when the engine is switched off!
Remove ignition key!
Secure the machine against rolling away!
The hydraulic system is under high pressure!
Fluids escaping under high pressure can penetrate the skin and cause serious injuries!
If such injuries occur, call a doctor immediately as otherwise there is a risk of serious
infection!
Repair work to the hydraulic system may only be carried out by an authorized dealer.
Hydraulic oil and used oil filters are to be stored in suitable containers and disposed of
in accordance with the regulations.
Caution! Hot oil can cause serious burns!
Only work on the hydraulic system when the engine is switched off!
Remove ignition key!
Secure the machine against rolling away!
Hydraulic cylinders
Prior to storing the machine (e.g. for winter period), all hydraulic cylinders must be cleaned and
completely retracted to protect them against contamination and corrosion. If a complete retraction is not
possible, lubricate the cylinders and cover them by means of a blanket. Contaminated and corroded
cylinder rods my damage the seals of they hydraulic cylinders when being retracted/extended the first
time after the winter storage!
Periodic maintenance:

Visual inspection for leads.

Check soiling indicator on filter (only with optional separate hydraulics)
Maintenance at the end of the harvesting season:
-change filter as instructed
Changing the filter:
-cleanliness is important when changing a filter
-Insert the new filter immediately after removing the old one.
-Release filter, unscrew and replace with an original SPUDNIK filter.
Insert the new filter as follows:
-Moisten the sealing face with oil.
-After the filter seal has made contact with the sealing face of the filter housing, tighten the filter
approximately one more turn.
-Check the filter for leads after a test run; retighten if necessary.
-Check the hydraulic fluid level and top up if necessary.
63
Operator's Manual MODEL 5640
Maintenance
Hydraulic system
Periodic maintenance:

Visual inspection for leads.

Check level
Maintenance at the end of the harvesting season:
-change oil as instructed
Changing the oil and checking the level:
Clean the area around the filling nozzle thoroughly before filling the system with new oil.
-Drain the old oil from the tank through the drain plug.
-Collect waste oil and dispose of it in accordance with the statutory regulations on environmental
protection.
-Refit the drain plug after all the oil has been drained.
-Fill up through the filter plug with the required quantity of a new oil to the correct specification.
-Check the level.
See the following figure for further information on changing the oil.
64
Operator's Manual MODEL 5640
Maintenance
Electrical system
Always disconnect the power supply prior to carrying out any work on the electrical
system.
Only use the original fuses. The use of fuses with a higher rating will cause
irreparable damage to the electrics.
Power supply
Only available when the tractor is supplied with the retrofitting cable.
Electrical cabinet
The machine’s entire electrical controls are located in the electrical cabinet. All the fuses for protecting
the machines are located here.
All the drawings for the machine are also kept in the electrical cabinet.
-Fuse diagram
-Wiring diagrams
-Hydraulic layouts
It is advisable to keep this operating manual in the electrical cabinet as well. This ensures that the
manual is always available whenever the machine is being used.
Non-CCI box
CCI box
65
Operator's Manual MODEL 5640
Machine Parts Breakdown
Page #
Description_______________________________________________________
Safety Labels ………………...…………………………………………………………………...…..
16-18
Belted Chain Options …………………………………………………………………………………
69-73
Rear Axel ….……………………...…………………………………………………………………..
76
Tire Options …………………….……………………...……………………………………………....
78
Auto Back to Center……………………………… ..………….………………………………………
80
Drawbar Center Hitch………………………..……………………………………………...…………
82
Drawbar 34” LH Offset..………....……………………………………………..………………….…..
84
Drawbar 36” LH Offset…………..………………………….…………………………………….……
86
Support Wheel…….. .…………………………………………...……………………………………..
88
Coulter Wide ……………………….……..………………......….………………………………….…
90
Nose Wings ………………………..………………………………..………………………..………..
92
Rock Point ……………………………………………………………………….….………………….
94
Sand Point 7 Row ………….………………......………………..…….………………………………
96
Sand Point Extended Mount………………………………………….……………………….……….
98
Sand Point Short …..……………………………………………………….………………………….
100
Sand Point Wide .….……………………………………………………….………………………….
102
Clod Blade Narrow Nose …………………..………………………………………...…………….…
104
Clod Blade Wide Nose ………..…………………………………………………….…………….......
106
Dog Tongue Narrow Nose...……………………………………………………………..…….………
108
Dog Tongue Wide Nose……………………………………………………………………………..…
110
Half Clod Blade Narrow Nose….…………………………………………………………...…..…...
112
Half Clod Blade Wide Nose..……………………………………………………..………………...….
114
Rock Point Narrow Nose...……………………………………………………………………………..
116
Mechanical Shaker …………………………………………………………………………………….
118
Rotary Shaker…. ……………………………………………………………………………………….
120
Rocker Shaker Motor Mount...…………………………………………………………………….……
122
2 Chain 2.5” Roller Under Belt………………………………………….………………………………
124
2 Chain 3.5” Roller Under Belt……………………………………….…………………………………
126
2 Chain Roller Under Rods…………………………………………………………………………….
128
4 Chain 2.5” Roller Under Belt…………………………………………………………………………
130
4 Chain 3.5” Roller Under Belt…………………………………………………………………………
132
4 Chain Roller Under Rods…………………………………………………………………………….
134
4 Chain Kryptane Rollers Under Rods……………………………………………………………….
136
66
Operator's Manual MODEL 5640
Machine Parts Breakdown
Page #
Description_______________________________________________________
Wide Digging Nose…..………...…………………………………………………………………...…..
138
Narrow Digging Nose...…………………………………………………………………………………
140
Secondary…….……………………...…………………………………………………………………..
142
Vine Chain Standard Parts...……………………..……………...……………………………………..
144
Vine Chain Standard Parts….…………………………………………………...……………………...
146
Brush Roller ……………………………………….………………………………….………………….
148
Snapper Roller………………….……………………...……………………………………………....
150
Stripper Kit …………………………………………...………….………………………………………
152
Maindrive ……………………………………………………………………………………...…………
154
Maindrive ……………….………....……………………………………………..………………….…..
156
Hydraulics ………………………...………………………….…………………………………….……
158
Rear Cross Standard Parts ..…………………………………...……………………………………..
160
Rear Cross Chain Extension ………..…..………………......….………………………………….…
162
2 Spreader Rolls …………………...………………………………..………………………..………..
164
2 Spreader Rolls ……………..………………………………………………….….………………….
166
3 Spreader Rolls ……………………………......………………..…….………………………………
168
3 Spreader Rolls …………..………………………………………….……………………….……….
170
Side Elevator ……....……………………………………………………….………………………….
172
Side Elevator Chain Extension …...……………………………………….………………………….
174
Separator Side Elevator Parts …………..…………………………………………...…………….…
176
Eliminator Table ,…………………………………………………………………….…………….......
178
Finger Roll Parts ..………………………………………………………………………..…….………
180
Euroroll Parts ……………………..…………………………………………………………………..…
182
Kryptane Roller Parts ……………………………………………………………………………...…..
184
36” Picking Table ………………………..………………………………………..………………...….
186
36” Boom ………...……………………………………………………………………………………..
188
36” Hopper Options …………………………………………………………………………………….
190
36” Boom Mounting Parts……………………………………………………………………………….
192
42” Picking Table ………………………………………………………………………………….……
194
42” Boom …………….………………………………………………….………………………………
196
42” Hopper Options ………………………………………………….…………………………………
198
67
Operator's Manual MODEL 5640
Machine Parts Breakdown
Page #
Description_______________________________________________________
42” Boom Mounting Options…..…………………………………………………………………...…..
200
Bolt on Frame Catwalk ...………………………………………………………………………………
202
Bolt on Boom Catwalk .…………...…………………………………………………………………..
204
Catwalk With Canopy ….………………………..……………...……………………………………..
206
Lights …………………………………………………………………………………………………….
208
Blower …………………...……………………………………………………...……………………...
210
Blower Plenum …………………..………………………………………………….………………….
212
Toolkit …………...……………….……………………...……………………………………………....
214
Standard Shields ……………………………………………………………………………………….
216
Shields with Brushroller..………………………….....………….………………………………………
218
68
Operator's Manual MODEL 5640
Belted Chain Options
Assy #
351449
351450
351451
351452
351441
351442
351443
351444
Assy #
351334
351357
351319
351363
351433
351434
351435
351436
Assy #
351445
351446
351447
351448
351437
351438
351439
351440
Assy #
352716
352717
352718
352719
352720
352721
352722
352723
Primary chain wide nose (2-chain)
Description
ASSY,BC,69"x13MMx42MM 2D 1S BARE 16'6"
ASSY,BC,69"x13MMx45MM 2D 1S BARE 16'6"
ASSY,BC,69"x13MMx50MM 2D 1S BARE 16'6"
ASSY,BC,69"x13MMx56MM 2D 1S BARE 16'6"
ASSY,BC,69"x13MMx42MM STR BARE 16'6"
ASSY,BC,69"x13MMx45MM STR BARE 16'6"
ASSY,BC,69"x13MMx50MM STR BARE 16'6"
ASSY,BC,69"x13MMx56MM STR BARE 16'6"
Primary chain wide nose (4-chain)
Description
ASSY,BC,33"x12.5MMx42MM 2D 1S BARE 16'6"
ASSY,BC,33"x12.5MMx45MM 2D 1S BARE 16'6"
ASSY,BC,33"x12.5MMx50MM 2D 1S BARE 16'6"
ASSY,BC,33"x12.5MMx56MM 2D 1S BARE 16'6"
ASSY,BC,33"x12.5MMx42MM STR BARE 16'6"
ASSY,BC,33"x12.5MMx45MM STR BARE 16'6"
ASSY,BC,33"x12.5MMx50MM STR BARE 16'6"
ASSY,BC,33"x12.5MMx56MM STR BARE 16'6"
Primary chain wide nose (2-chain)
Description
ASSY,BC,66"x13MMx42MM 2D 1S BARE 16'6"
ASSY,BC,66"x13MMx45MM 2D 1S BARE 16'6"
ASSY,BC,66"x13MMx50MM 2D 1S BARE 16'6"
ASSY,BC,66"x13MMx56MM 2D 1S BARE 16'6"
ASSY,BC,66"x13MMx42MM STR BARE 16'6"
ASSY,BC,66"x13MMx45MM STR BARE 16'6"
ASSY,BC,66"x13MMx50MM STR BARE 16'6"
ASSY,BC,66"x13MMx56MM STR BARE 16'6"
Primary chain wide nose (4-chain)
Description
ASSY,BC,31"x12.5MMx42MM STR BARE 16'6"
ASSY,BC,31"x12.5MMx45MM STR BARE 16'6"
ASSY,BC,31"x12.5MMx50MM STR BARE 16' 6"
ASSY,BC,31"x12.5MMx56MM STR BARE 16'6"
ASSY,BC,31"x12.5MMx42MM 2D 1S BARE 16'6"
ASSY,BC,31"x12.5MMx45MM 2D 1S BARE 16'6"
ASSY,BC,31"x12.5MMx50MM 2D 1S BARE 16'6"
ASSY,BC,31"x12.5MMx56MM 2D 1S BARE 16'6"
69
Operator's Manual MODEL 5640
Belted Chain Options
70
Assy #
352511
352512
352513
352514
352515
352516
352517
352518
352519
352520
352521
352522
352523
352524
352525
352526
352527
352528
Secondary chain options
Description
ASSY,BC,69"x11MMx42MM 5D CU 2P 19'6"
ASSY,BC,69"x11MMx45MM 5D CU 2P 19'6"
ASSY,BC,69"x11MMx50MM 5D CU 2P 19'6"
ASSY,BC,69"x11MMx56MM 5D CU 2P 19'6"
ASSY,BC,69"x11MMx42MM 5D CFLEX 2P 19'6"
ASSY,BC,69"x11MMx45MM 5D CFLEX 2P 19'6"
ASSY,BC,69"x11MMx50MM 5D CFLEX 2P 19'6"
ASSY,BC,69"x11MMx56MM 5D CFLEX 2P 22'5"
ASSY,BC,69"x11MMx42MM 5D PIL 2P 19'6"
ASSY,BC,69"x11MMx45MM 5D PIL 2P 19'6"
ASSY,BC,69"x11MMx50MM 5D PIL 2P 19'6"
ASSY,BC,69"x11MMx56MM 5D PIL 2P 19'6"
ASSY,BC,69"x11MMx42MM 5D AIR 2P 19'6"
ASSY,BC,69"x11MMx45MM 5D AIR 2P 19'6"
ASSY,BC,69"x11MMx50MM 5D AIR 2P 19'6"
ASSY,BC,69"x11MMx56MM 5D AIR 2P 19'6"
ASSY,BC,69"x11MMx45MM 5DCFLXEAR 2P 19'6"
ASSY,BC,69"x11MMx50MM 5DCFLXEAR 2P 19'6"
Assy #
351325
351370
Vine chain options
Description
ASSY,BC,69"x15MMx150MM STR CUSH 30'0"
ASSY,BC,69"x15MMx180MM STR CUSH 30'0"
Operator's Manual MODEL 5640
Belted Chain Options
Assy #
352204
352205
352206
352207
352208
352209
352210
352211
352216
352217
352218
352219
352212
352213
352214
352215
352294
352295
352298
352299
Rear cross options
Description
ASSY,BC,42"x11MMx42MM STR CUSH 32'0"
ASSY,BC,42"x11MMx45MM STR CUSH 32'0"
ASSY,BC,42"x11MMx50MM STR CUSH 32'0"
ASSY,BC,42"x11MMx56MM STR CUSH 32'0"
ASSY,BC,42"x11MMx42MM STR CFLEX 32'0"
ASSY,BC,42"x11MMx45MM STR CFLEX 32'0"
ASSY,BC,42"x11MMx50MM STR CFLEX 32'0"
ASSY,BC,42"x11MMx56MM STR CFLEX 32'0"
ASSY,BC,42"x11MMx42MM STR PIL 32'0"
ASSY,BC,42"x11MMx45MM STR PIL 32'0"
ASSY,BC,42"x11MMx50MM STR PIL 32'0"
ASSY,BC,42"x11MMx56MM STR PIL 32'0"
ASSY,BC,42"x11MMx42MM STR AIR 32'0"
ASSY,BC,42"x11MMx45MM STR AIR 32'0"
ASSY,BC,42"x11MMx50MM STR AIR 32'0"
ASSY,BC,42"x11MMx56MM STR AIR 32'0"
ASSY,BC,42"x11MMx42MM S CFLX LHEAR 32'0"
ASSY,BC,42"x11MMx45MM S CFLX LHEAR 32'0"
ASSY,BC,42"x11MMx50MM S CFLX LHEAR 32'0"
ASSY,BC,42"x11MMx56MM S CFLX LHEAR 32'0"
Assy #
352952
352953
352954
352955
352956
352957
352958
352959
352960
352961
352962
352963
352964
352965
352940
Side elevator chain options
Description
ASSY,BC,42"x11MMx42MM 5D CU 2P 33' 3"
ASSY,BC,42"x11MMx45MM 5D CU 2P 33' 3"
ASSY,BC,42"x11MMx50MM 5D CU 2P 33' 3"
ASSY,BC,42"x11MMx42MM 5D CFLEX 2P 40' 6"
ASSY,BC,42"x11MMx45MM 5D CFLEX 2P 33' 3"
ASSY,BC,42"x11MMx50MM 5D CFLEX 2P 33' 3"
ASSY,BC,42"x11MMx42MM 5D PIL 2P 33' 3"
ASSY,BC,42"x11MMx45MM 5D PIL 2P 33' 3"
ASSY,BC,42"x11MMx50MM 5D PIL 2P 33' 3"
ASSY,BC,42"x11MMx42MM 5D AIR 2P 33' 3"
ASSY,BC,42"x11MMx45MM 5D AIR 2P 33' 3"
ASSY,BC,42"x11MMx50MM 5D AIR 2P 37' 3"
ASSY,BC,42"x11MMx45MM 5DCFLXEAR2P 33' 3"
ASSY,BC,42"x11MMx50MM 5DCFLXEAR2P 33' 3"
ASSY,BC,42"x11MMx42MM 5D CU 2P 40' 6"
71
Operator's Manual MODEL 5640
Belted Chain Options
72
352941
352942
352943
352944
352945
352946
352947
352948
352949
352950
352951
352969
352970
352966
352967
352968
ASSY,BC,42"x11MMx45MM 5D CU 2P 40' 6"
ASSY,BC,42"x11MMx50MM 5D CU 2P 40' 6"
ASSY,BC,42"x11MMx42MM 5D CFLEX 2P 40' 6"
ASSY,BC,42"x11MMx45MM 5D CFLEX 2P 40' 6"
ASSY,BC,42"x11MMx50MM 5D CFLEX 2P 40' 6"
ASSY,BC,42"x11MMx42MM 5D PIL 2P 40' 6"
ASSY,BC,42"x11MMx45MM 5D PIL 2P 40' 6"
ASSY,BC,42"x11MMx50MM 5D PIL 2P 40' 6"
ASSY,BC,42"x11MMx42MM 5D AIR 2P 40' 6"
ASSY,BC,42"x11MMx45MM 5D AIR 2P 40' 6"
ASSY,BC,42"x11MMx50MM 5D AIR 2P 40' 6"
ASSY,BC,42"x11MMx45MM 5DCFLXEAR2P 40' 6"
ASSY,BC,42"x11MMx50MM 5DCFLXEAR2P 40' 6"
ASSY,BC,42"x11MMx42MM 3DN1STR CU 33' 3"
ASSY,BC,42"x11MMx45MM 3DN1STR CU 33' 3"
ASSY,BC,42"x11MMx50MM 3DN1STR CU 33' 3"
Assy #
351532
351342
351372
351533
351534
351535
351536
351537
351538
351539
351540
Boom chain option
Description
ASSY,BC,36"x11MMx42MM 5D CU 2P 61'2"
ASSY,BC,36"x11MMx45MM 5D CU 2P 61' 2"
ASSY,BC,36"x11MMx50MM 5D CU 2P 61'2"
ASSY,BC,36"x11MMx42MM 5D CFLEX 2P 61'2"
ASSY,BC,36"x11MMx45MM 5D CFLEX 2P 61'2"
ASSY,BC,36"x11MMx50MM 5D CFLEX 2P 61'2"
ASSY,BC,36"x11MMx42MM 5D PIL 2P 61'2"
ASSY,BC,36"x11MMx45MM 5D PIL 2P 61'2"
ASSY,BC,36"x11MMx50MM 5D PIL 2P 61'2"
ASSY,BC,36"x11MMx42MM 5D AIR 2P 61'2"
ASSY,BC,36"x11MMx45MM 5D AIR 2P 61'2"
Operator's Manual MODEL 5640
Belted Chain Options
351321
351979
351983
352223
352224
352225
352226
352227
352228
352229
352230
352231
352232
352233
352234
352235
352236
ASSY,BC,36"x11MMx50MM 5D AIR 2P 61'2"
ASSY,BC,36"x11MMx45MM 5DCFLXEAR 2P 61'2"
ASSY,BC,36"x11MMx50MM 5DCFLXEAR 2P 61'2"
ASSY,BC,42"x11MMx42MM 5D CU 2P 61'2"
ASSY,BC,42"x11MMx45MM 5D CU 2P 61'2"
ASSY,BC,42"x11MMx50MM 5D CU 2P 61'2"
ASSY,BC,42"x11MMx42MM 5D CFLEX 2P 61'2"
ASSY,BC,42"x11MMx45MM 5D CFLEX 2P 61'2"
ASSY,BC,42"x11MMx50MM 5D CFLEX 2P 61'2"
ASSY,BC,42"x11MMx42MM 5D PIL 2P 61'2"
ASSY,BC,42"x11MMx45MM 5D PIL 2P 61'2"
ASSY,BC,42"x11MMx50MM 5D PIL 2P 61'2"
ASSY,BC,42"x11MMx42MM 5D AIR 2P 61'2"
ASSY,BC,42"x11MMx45MM 5D AIR 2P 61'2"
ASSY,BC,42"x11MMx50MM 5D AIR 2P 61'2"
ASSY,BC,42"x11MMx45MM 5DCFLXEAR 2P 61'2"
ASSY,BC,42"x11MMx50MM 5DCFLXEAR 2P 61'2"
73
Operator's Manual MODEL 5640
Notes !!
74
Operator's Manual MODEL 5640
Notes !!
75
Operator's Manual MODEL 5640
AXLE ARM SUPPORT 174359
76
Operator's Manual MODEL 5640
Rear axle
Item #
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
Quantity
2
2
1
4
2
2
2
4
6
2
2
2
2
2
20
1
20
2
2
2
2
2
Part #
194694
197200
171408
191933
602628
181576
231252
231253
231155
231152
174061
951216
951200
501954
951222
951175
951220
231109
951218
231108
951221
951153
Description
SPINDLE BLOCK WELDMENT 5640-2007
AXLE,SLIDE,5640-2012
TOW,ANGLE,STEERING,3/8"x2" x 28-3/4"5600
KING PIN 6400 GS
CYL,3.00"x8",TIE ROD,20.25",REPHASE
PIN,AXLE,PLACEMENT,1-1/4"x8-1/2" 1"-8UNC
BRNG,THRUST,PACK,2"IDx3" 114 OD,FTS3252
BRNG,JOURNAL,STEEL/PTFE,2" IDx2",CJS3232
BUSHING,TENSION 1"ID x 1/8"WALL x 1"L
BUSHING,TENSION 1"ID x 1/8"WALL x 3/4"L
REAR AXLE HYD CYL MOUNT PLATE,5640-2007
CAP,DUST 10 HOLE BOLT-ON
NUT,SLOTTED,HEX,2"-12UNF x 1-1/8" THICK
COLLAR,SHAFT,SET,SCREW,2"
NUT,LUG,3/4"-16UNF WITH FLANGE
HUB,COMPLETE,10HOLE,13.187"BC,11"PILOT
STUD,BOLT,3/4"-18UNF(10HOLE HUB)
BRNG,WHEEL,10 HOLE OUTER HM212049
RACE,BEARING,10 HOLE OUTER CUP HM212011
BRNG,WHEEL,10 HOLE INNER HM218-248
RACE,BEARING,10 HOLE INNER CUP
SEAL,GREASE,INNER,10 HOLE CR-43771
77
Operator's Manual MODEL 5640
78
Operator's Manual MODEL 5640
Tire options
Item #
Quantity
Part #
Description
1
1
951271
TIRE,&,RIM,14x24" 16PLY GRADER LH 5640
2
2
951496
TIRE,&,RIM,12x24 20PLY0.912 OFS 5640
3
1
951439
TIRE,&,RIM 600/50x22.5ALLIANC LH 5640-08
4
1
951458
TIRE,&,RIM,14x24 16PLY DUAL GRAD LH 5640
5
1
951459
TIRE,&,RIM,14x24 16PLY DUAL GRAD RH 5640
6
7
1
1
951440
951434
TIRE,&,RIM 600/50x22.5ALLIANC RH 5640-08
TIRE,&,RIM,14x24" 16PLY GRADER RH 5640
79
Operator's Manual MODEL 5640
80
Operator's Manual MODEL 5640
Auto back to center
Item #
Quantity
Part #
Description
1
1
196523
MOUNT,POT,BACK TO CNTR KING PIN,5640-11
2
1
175118
ARM,POT,BACK TO CNTR KING PIN,5640-11
3
1
194845
POT ARM,WALKING BEAM 80XX-2009
4
1
981935
ROD END,SWIVEL,1/4-28UNC 6058K25
5
1
B94.02350
A-SENSOR,090°,10-30V(STRG,MSEP)
81
Operator's Manual MODEL 5640
82
Operator's Manual MODEL 5640
Drawbar Center Hitch
Item #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Quantity
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
Part #
196534
981963
195922
951212
951213
193675
193678
171455
981263
174421
571184
571184
231399
050760
231163
175119
175113
601536
Description
DRAWBAR,CENTER,BOLTABLE,5640-2011
HITCH,DRAWBAR HEAVY DUTY PIVOTING BALL
DRAWBAR,EXTENSION,6440-2010
JACK,HITCH,WELDMENT 5600/5100
EXTENSION,JACK,HITCH 5600
JACK LEG INNER HARV/6140-2006
JACK LEG OUTER HARV/6140-2006
PIN,CYLINDER,THIRD COULTER 5100/5600
HITCH,DRAWBAR,200-470HP
BRACKET,PTO REST,HARV-2008
PIN,KEEPER,JACK HANDLE 5/16"x2"(UMC PIN)
PIN,KEEPER,JACK HANDLE 5/16"x2"(UMC PIN)
BRNG,4 BOLT FLANGE,2"TAPERED SLEEVE LOCK
SHAFT,FRONT JACK,5640-2011
BRNG,4BOLT,FLNG,1-3/4"BORE ECCENTRIC LCK
BRACKET,HOSEGUIDE DRAWBAR,5640-11
HOSE GUIDE,DRAWBAR,5640-11
CYLNDR,TIE,ROD,3"x10" SAE 20-1/4"3000PSI
83
Operator's Manual MODEL 5640
84
Operator's Manual MODEL 5640
Drawbar 34" LH offset
Item #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Quantity
1
1
1
1
2
1
1
1
1
1
1
1
1
1
2
1
1
1
Part #
196536
951212
195922
981963
171455
193678
193675
951213
175634
175633
231399
050760
231163
601536
501220
571184
174421
981263
Description
DRAWBAR,OFFSET,LH,34"BOLTABLE,5640-2011
JACK,HITCH,WELDMENT 5600/5100
DRAWBAR,EXTENSION,6440-2010
HITCH,DRAWBAR HEAVY DUTY PIVOTING BALL
PIN,CYLINDER,THIRD COULTER 5100/5600
JACK LEG OUTER HARV/6140-2006
JACK LEG INNER HARV/6140-2006
EXTENSION,JACK,HITCH 5600
BRACKET,HOSE GUIDE,OFFSET DRAWBAR,5640-11
HOSE GUIDE,OFFSET DRAWBAR,5640-11
BRNG,4 BOLT FLANGE,2"TAPERED SLEEVE LOCK
SHAFT,FRONT JACK,5640-2011
BRNG,4BOLT,FLNG,1-3/4"BORE ECCENTRIC LCK
CYLNDR,TIE,ROD,3"x10" SAE 20-1/4"3000PSI
HAIRPIN,COTTER,3/16"x3-3/4" #21-08
PIN,KEEPER,JACK HANDLE 5/16"x2"(UMC PIN)
BRACKET,PTO REST,HARV-2008
HITCH,DRAWBAR,200-470HP
85
Operator's Manual MODEL 5640
86
Operator's Manual MODEL 5640
Drawbar 36" LH offset
Item #
1
2
3
4
5
6
7
Quantity
1
1
1
1
1
1
1
Part #
196537
195922
951212
951213
571184
193675
193678
Description
DRAWBAR,OFFSET,LH,36"BOLTABLE,5640-2011
DRAWBAR,EXTENSION,6440-2010
JACK,HITCH,WELDMENT 5600/5100
EXTENSION,JACK,HITCH 5600
PIN,KEEPER,JACK HANDLE 5/16"x2"(UMC PIN)
JACK LEG INNER HARV/6140-2006
JACK LEG OUTER HARV/6140-2006
8
9
10
11
12
13
14
15
16
17
18
19
20
2
1
1
1
1
1
1
1
1
1
1
2
1
171455
981963
981263
174421
175633
175634
192515
019.00487
231399
050760
231163
501220
601536
PIN,CYLINDER,THIRD COULTER 5100/5600
HITCH,DRAWBAR HEAVY DUTY PIVOTING BALL
HITCH,DRAWBAR,200-470HP
BRACKET,PTO REST,HARV-2008
HOSE GUIDE,OFFSET DRAWBAR,5640-11
BRACKET,HOSE GUIDE,OFFSET DRAWBAR,5640-11
SHIELD,FRNT PTO EXTND HARV-2004
HINGE,1-15/16"
BRNG,4 BOLT FLANGE,2"TAPERED SLEEVE LOCK
SHAFT,FRONT JACK,5640-2011
BRNG,4BOLT,FLNG,1-3/4"BORE ECCENTRIC LCK
HAIRPIN,COTTER,3/16"x3-3/4" #21-08
CYLNDR,TIE,ROD,3"x10" SAE 20-1/4"3000PSI
87
Operator's Manual MODEL 5640
88
Operator's Manual MODEL 5640
Support wheel
Item #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
Quantity
1
2
2
1
1
1
1
4
4
2
2
1
1
1
1
2
1
2
8
Part #
192238
192237
602619
196535
951280
171822
951347
181604
502292
501087
501934
171447
502630
172047
231166
231163
821409
502331
951198
Description
SUPPORT WHEEL PIVOT MOUNT 6400
SUPPORT WHEEL PARALLEL ARM 6400
CYL,3.00"x8",TIE ROD,20.25",1.375",3/4
SUPPORT FRAME,SUPPORT WHEEL,5640-2011
TIRE,&,RIM 12.5L16 14PLY SUPPORT WHEEL
BRACKET,CRZY,WHL,16" BARE HARV RETROFIT
HUB,CAST,8HOLE,1-3/4"BORE,CRAZY WHL
PIN,SUPPORT,WHEEL WELDMENT
PIN,ROLL,1/4" x 1"
BOLT,HEX,HD,1/2"-13UNC x 1-1/2" GR 5
WASHER,LOCK,SPLIT,1/2"
CAP SUPPORT WHEEL
FITTING,GREASE,1/4"-28x1-1/8 STR #1698-B
PLATE WEAR CRAZY WHEEL
BRNG,THRUST,4.5"ODx3"IDx.058 RBC FTS4872
BRNG,4BOLT,FLNG,1-3/4"BORE ECCENTRIC LCK
SHFT,SK,1-3/4"x18" (4.25) 3/8" KEYWAY
COLLAR,SHAFT,SET,SCREW,1-3/4"
NUT,LUG,WHEEL,5/8"-18UNF (8 HOLE HUB)
89
Operator's Manual MODEL 5640
90
Operator's Manual MODEL 5640
Coulter wide
Item #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
Quantity
2
2
2
6
16
2
2
2
12
4
4
2
2
2
2
2
4
2
2
2
2
4
3
2
2
2
4
4
2
2
2
1
1
Part #
194734
602612
194733
501713
502644
171806
171807
502688
172978
174224
501220
050009
501817
501938
090273
321580
501217
171367
981267
194735
231253
951187
502292
210002
201053
951171
951172
231125
310035
571079
210032
210001
210003
Description
COULTER ARM UNIVERSAL 6140/HARV-2007
CYL,2.00"x8",TIE ROD,20.25",1.125",3/4
COULTER SWING ARM UNIVERSAL
NUT,LOCK,HEX,1"-8UNC NYLON INSERT
WASHER,FLAT,1"(SAE) ZINC PLTD (ASMB)
SPACER,CYL,SHKR,1/4"x1.13"IDx2.25"ID
SPACER,CYL,SHKR,1/2"x1.13"IDx2.25"OD
BOLT,HEX,HD,1"-8UNC x 6-1/2" GR8
PLATE,DISC COULTER MOUNT
COULTER HINGE ARM UNIV-2007
HAIRPIN,COTTER,3/16"x3-3/4" #21-08
PIN,DISC COULTER HYD CYL MOUNT
NUT,HEX,1"-8UNC
WASHER,LOCK,SPLIT,1"
SPACER TUBE 1.25" ID x 3.25" LONG
TRUNNION,COULTER,SPRING,STOP 2"x2"x4.50"
BOLT,HEX,HD,1"-8UNC x 6" GR 5
SPACER,COULTER,TENSION,ROD,1.5"ODx1.5"LG
SPRING,24"x2",COMPRESSION .437"DIA WIRE
COULTER SPRING BOLT SINGLE PADEYE
BRNG,JOURNAL,STEEL/PTFE,2" IDx2",CJS3232
WASHER,LOCKPIN,.546"IDx2.38"ODx.250"THCK
PIN,ROLL,1/4" x 1"
COULTER,28",STR,1/4 T1,6HOLE,5-1/4"BC
SPINDLE,CLTR,ARM NRRW NOSE 2"x9-1/4"
SEAL,WHEEL,BEARING,2.625"x3.500"x.375"
RACE,TAPERED,2",BEARING,WHEEL CUP
BRNG,WHEEL,2",TAPERED ROLLER(WHEEL CONE)
HUB,COULTER,4"ODx2.9"IDx3"L,6HOLE,5.25BC
CAP,DUST,WHL,DRV,GRBX FOR #710 (3.255")
PLATE,COULTER,REINFORCEMENT,1/4" x 6HOLE
COULTER,28",WAVY,3/8"T1,6HOLE 5-1/4"BC
COULTER,28",NOTCH,1/4 T1,6HL,5.25"BC
91
Operator's Manual MODEL 5640
92
Operator's Manual MODEL 5640
Nose wings
Item #
Quantity
Part #
Description
1
1
172991
PLATE
2
1
192273
NOSE WING SHORT
3
1
192272
NOSE WING LONG
4
1
194316
NOSE WING RH EXT SANDPT BLADE 6400-2007
5
1
194315
NOSE WING LH EXT SANDPT BLADE 6400-2007
6
1
195659
NOSE WING,LONG,4IN EXTENDED,HARV-2010
7
1
195676
NOSE WING,LH,EXT BLADE,STAINLESS STEEL
8
1
195675
NOSE WING,RH,EXT BLADE,STAINLESS STEEL
9
1
195673
NOSE WING,LONG STAINLESS STEEL
10
1
195674
NOSE WING,SHORT STAINLESS STEEL
93
Operator's Manual MODEL 5640
94
Operator's Manual MODEL 5640
Rock point
Item #
Quantity
Part #
Description
1
1
210027
BLADE,ROCK,POINT,WIDE L.H. 5140/5640
2
1
210029
BLADE,ROCK,POINT,WIDE R.H. 5140/5640
3
1
210187
BLADE,CENTER FILLER FLAT SLOTTED
4
5
2
2
020314
020313
SUPPORT,PLATE,UNIV NOSE 6140-2004
SPACER,CENTERBRD UNIV NOSE 6140-2004
95
Operator's Manual MODEL 5640
96
Operator's Manual MODEL 5640
Sand point 7 row
Item #
Quantity
Part #
Description
1
2
210005
MOUNT,BAR,SAND,POINT,WIDE DIGGER NOSE
2
1
210190
BLADE,SANDPT STR LH WIDE 6400-05
3
1
210191
BLADE,SANDPT STR RH WIDE 6400-05
4
5
2
2
020314
020313
SUPPORT,PLATE,UNIV NOSE 6140-2004
SPACER,CENTERBRD UNIV NOSE 6140-2004
97
Operator's Manual MODEL 5640
98
Operator's Manual MODEL 5640
Sand point extended mount
Item #
1
2
3
4
5
6
7
8
9
10
Quantity
2
2
1
2
1
2
1
1
2
2
Part #
210005
981717
210007
210009
210008
210010
210197
210203
025495
020313
Description
MOUNT,BAR,SAND,POINT,WIDE DIGGER NOSE
UHMW,STONEFLP,WIDE 6140/6400-2005
BLADE,SAND,POINT,LH,WIDE OUTER 5140/5640
BLADE,SAND,POINT,CNTR,WIDE 5140/5640
BLADE,SAND,POINT,RH,WIDE OUTER 5140/5640
BLADE,SAND,POINT,SOLID,QRTR COVER WIDE
BLADE,CENTER FILLER SANDPT EXT
BLADE,CENER FILLER SANDPT 14"
CENTERBD BRACKET LG EXT SANDPT
SPACER,CENTERBRD UNIV NOSE 6140-2004
99
Operator's Manual MODEL 5640
100
Operator's Manual MODEL 5640
Sand point short
Item #
1
2
3
4
5
6
7
8
9
10
Quantity
2
2
2
1
1
1
1
1
2
2
Part #
210004
210253
210016
210187
210021
210006
210024
210023
020314
020313
Description
MOUNT,BAR,SAND,POINT,NARROW DIGGER NOSE
BLADEMFLLR,QTR,NRRW/WIDE SANDPOINT,2012
BLADE,SAND,POINT,SOLID,QRTR COVER NARROW
BLADE,CENTER FILLER FLAT SLOTTED
BLADE,SAND,POINT,LH,NRRW OUTER 5140/5640
BLADE,SAND,POINT,LH,NRRW,INNER 5140/5640
BLADE,SAND,POINT,RH,NRRW INNER 5140/5640
BLADE,SAND,POINT,RH,NRRW OUTER 5140/5640
SUPPORT,PLATE,UNIV NOSE 6140-2004
SPACER,CENTERBRD UNIV NOSE 6140-2004
101
Operator's Manual MODEL 5640
102
Operator's Manual MODEL 5640
Sand point wide
Item #
1
2
3
4
5
6
7
8
9
Quantity
2
1
2
1
2
1
2
2
2
Part #
210005
210007
210009
210008
210010
210187
210197
020314
020313
Description
MOUNT,BAR,SAND,POINT,WIDE DIGGER NOSE
BLADE,SAND,POINT,LH,WIDE OUTER 5140/5640
BLADE,SAND,POINT,CNTR,WIDE 5140/5640
BLADE,SAND,POINT,RH,WIDE OUTER 5140/5640
BLADE,SAND,POINT,SOLID,QRTR COVER WIDE
BLADE,CENTER FILLER FLAT SLOTTED
BLADE,CENTER FILLER SANDPT EXT
SUPPORT,PLATE,UNIV NOSE 6140-2004
SPACER,CENTERBRD UNIV NOSE 6140-2004
103
Operator's Manual MODEL 5640
104
Operator's Manual MODEL 5640
Clod blade narrow nose
Item #
Quantity
Part #
Description
1
1
210202
BLADE,CLOD,REINF,NO CTR 32/34 LH 4ROW-07
2
1
210201
BLADE,CLOD,REINF,NO CTR 32/34 RH 4ROW-07
3
2
020314
SUPPORT,PLATE,UNIV NOSE 6140-2004
4
2
020313
SPACER,CENTERBRD UNIV NOSE 6140-2004
105
Operator's Manual MODEL 5640
106
Operator's Manual MODEL 5640
Clod blade wide nose
Item #
Quantity
Part #
Description
1
1
210200
BLADE,CLOD,REINF,NO CTR 36/38 LH 4ROW-07
2
3
1
2
210199
020314
BLADE,CLOD,REINF,NO CTR 36/38 RH 4ROW-07
SUPPORT,PLATE,UNIV NOSE 6140-2004
4
2
020313
SPACER,CENTERBRD UNIV NOSE 6140-2004
107
Operator's Manual MODEL 5640
108
Operator's Manual MODEL 5640
Dog tongue narrow nose
Item #
Quantity
Part #
Description
1
1
210052
BLADE,DOG,TONGUE,NARROW L.H. ALL
2
1
210020
BLADE,DOG,TONGUE,NARROW R.H. ALL
3
2
192754
SPACR,NRRW TO WIDE NOSE 4ROW-2005
4
2
E00354
BLADE,QUARTER FILLER WADA SPECIAL
5
6
7
1
2
2
E00353
020314
020313
BLADE,CENTER FILLER DOG TONGUE
SUPPORT,PLATE,UNIV NOSE 6140-2004
SPACER,CENTERBRD UNIV NOSE 6140-2004
109
Operator's Manual MODEL 5640
110
Operator's Manual MODEL 5640
Dog tongue wide nose
Item #
Quantity
Part #
Description
1
1
210051
BLADE,DOG,TONGUE,WIDE L.H. ALL
2
1
210022
BLADE,DOG,TONGUE,WIDE R.H. ALL
3
2
E00354
BLADE,QUARTER FILLER WADA SPECIAL
4
1
E00353
BLADE,CENTER FILLER DOG TONGUE
5
6
2
2
020314
020313
SUPPORT,PLATE,UNIV NOSE 6140-2004
SPACER,CENTERBRD UNIV NOSE 6140-2004
111
Operator's Manual MODEL 5640
112
Operator's Manual MODEL 5640
Half clod blade narrow nose
Item #
1
2
3
4
5
6
7
Quantity
1
2
1
2
1
2
2
Part #
131827
192754
131826
210147
210146
020314
020313
Description
BLADE,HALF CLOD 32/34 RH NRRW 4-ROW
SPACR,NRRW TO WIDE NOSE 4ROW-2005
BLADE,HALF CLOD 32/34 LH NRRW 4-ROW
BLADE,QUARTER FILLER HALF CLOD
BLADE,CENTER FILLER HALF CLOD
SUPPORT,PLATE,UNIV NOSE 6140-2004
SPACER,CENTERBRD UNIV NOSE 6140-2004
113
Operator's Manual MODEL 5640
114
Operator's Manual MODEL 5640
Half clod blade wide nose
Item #
Quantity
Part #
Description
1
1
131829
BLADE,HALF CLOD 36/38 LH WIDE 4-ROW
2
1
131828
BLADE,HALF CLOD 36/38 RH WIDE 4-ROW
3
2
210147
BLADE,QUARTER FILLER HALF CLOD
4
1
210146
BLADE,CENTER FILLER HALF CLOD
5
6
2
2
020314
020313
SUPPORT,PLATE,UNIV NOSE 6140-2004
SPACER,CENTERBRD UNIV NOSE 6140-2004
115
Operator's Manual MODEL 5640
116
Operator's Manual MODEL 5640
Rock point narrow nose
Item #
Quantity
Part #
Description
1
1
210026
BLADE,ROCK,POINT,NARROW L.H. 5140/5640
2
1
210028
BLADE,ROCK,POINT,NARROW R.H. 5140/5640
3
2
020314
SUPPORT,PLATE,UNIV NOSE 6140-2004
4
2
020313
SPACER,CENTERBRD UNIV NOSE 6140-2004
117
Operator's Manual MODEL 5640
118
Operator's Manual MODEL 5640
Mechanical shaker
Item #
1
2
3
4
5
6
7
8
9
10
11
12
Quantity
1
1
1
8
8
2
2
2
5
8
8
4
Part #
195005
192108
195688
321588
321593
602612
951284
173753
171807
351314
351309
174672
Description
SWINGFRAME,WIDE,5640-2008
SHAKER,WELDMENT,MECH,WIDE 6400-2004
SHAKER,WELDMENT,MECH,NRRW,4ROW-2010
SHAKER,TRI,UNIVERSAL 5/8" BORE W/2BRNG
SHAKER,TRI,UNVRSL,URETHANE 5/8"BR W/2BRN
CYL,2.00"x8",TIE ROD,20.25",1.125",3/4
JACK,RATCHET HEAVY DUTY #SL1541GT
DIGGERNOSE HYD CYLDR MOUNT AFT 2006
SPACER,CYL,SHKR,1/2"x1.13"IDx2.25"OD
RLR,BC,PU,5/8X4X1,PC
STANDOFF,RLR,BC,5/8"x1-1/4"
MOUNT,RLR,MECH SHAKER,HARV WIND-2010
119
Operator's Manual MODEL 5640
120
Operator's Manual MODEL 5640
Rotary shaker
Item #
1
2
3
4
5
6
7
8
9
Quantity
8
6
1
3
1
1
1
32
1
Part #
171440
231117
050249
231114
020764
901713
601655
351316
181593
Description
MOUNT,SHAKER,ROLLER,HYD,OPT 3/8"x7"x7"
HOUSING,BRNG,4HOLE,85MM,FLANGETTE PLATED
SHAFT,SHAKER,ROCKER,6400-2006
BRNG,INSERT,1-3/4",ECC,LOCK/SPHR
PLATE
ARM,TORQUE,HYD,SHKR 3/8" x 19.25
MTR,HY,3.0CUIN,1"KEY,SAE-A,TB-SERIES
RLR,BC,PU,5/8X3.5X2.375,PC
COUPLING,1-3/4"x1"x3-3/4" 1/4"&3/8" KEY
121
Operator's Manual MODEL 5640
122
Operator's Manual MODEL 5640
Rocker shaker motor mount
Item #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Quantity
8
2
2
2
2
2
2
2
2
2
4
16
2
2
2
1
8
4
Part #
191943
191944
191946
191903
601657
E00789
181986
022075
022076
231251
502208
351316
231262
181876
821574
173320
231117
231114
Description
LIFT ARM,ROCKER SHAKER 2004
ADJUSTER,ROCKER SHAKER
WELD,ROCKER SHAKER ARM NUT
ROCKER ARM,ROCKER SHAKER
MTR,HY,10.3CUIN,1"KEY,6-HOLE,TF-SERIES
PLATE,ROCKER SHAKER MTR MOUNT
ROCKER,SHAKER ECCENTRIC
SPACER,ROCKR SHAKR 6140/6400-2004
WASHER,ROCKR SHAKR 6140/HARV-2005
BRNG,HANGER 2-15/16"BORE
NUT,ACME,1-1/8"-5,RH,THREAD HEAVY HEX CS
RLR,BC,PU,5/8X3.5X2.375,PC
BRNG,SLEEVE,2" ODx1.75"x1.75LG
STEEL BUSHING ROCKR SHAKER
SHFT,QT,1-3/4"x76.75"HYD SHAKER 4 ROW
SPACER,SHAKER,BRNG 6140/6400-2005
HOUSING,BRNG,4HOLE,85MM,FLANGETTE PLATED
BRNG,INSERT,1-3/4",ECC,LOCK/SPHR
123
Operator's Manual MODEL 5640
124
Operator's Manual MODEL 5640
2 chain 2.5" roller under belt
Item #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Quantity
4
4
2
1
1
1
3
2
2
6
14
8
6
3
2
2
4
1
1
1
Part #
195769
H00493
H00492
502337
502650
502766
352280
171310
352725
351310
351313
351309
351316
171313
019.00435
351311
321584
321573
321576
321570
Description
ANTIWRAP,BOLT ON,WELDED,HARV-WIND-2010
ROLLER PLT,PRIMARY AFT,2CHAIN 6140-2004
ROLLER PLT,PRIMARY FWD,2CHAIN 6140-2004
BOLT,HEX,HD,5/8"-11UNC x 7" **GR8**
BOLT,HEX,HD,5/8"-11UNC x 5-1/2 GR8
BOLT,HEX,HD,5/8"-11UNC x 4-1/2" GR8
RLR,BC,ST,5/8X2.5X2.375X4FL,SC
SPACER,NOSE,ROLLER,3/8"x2.5"ODx11/16"ID
RLR,BC,ST,5/8X2.5X2.375,SC
STANDOFF,RLR,BC,5/8"x3-5/8"
RLR,BC,PU,5/8X5X1,PC
STANDOFF,RLR,BC,5/8"x1-1/4"
RLR,BC,PU,5/8X3.5X2.375,PC
SPACER,NOSE,ROLLER,1/4"x5"ODx11/16"ID
WINDING PROTECTION 5.250"
RLR,BC,PU,5/8X3.5X2.375X5FL,PC
SPRCKT,CAST,10T 56MM 2"BORE 1/2"
SPRCKT,CAST,12T 42MM 2"BORE 1/2"
SPRCKT,CAST,12T 45MM 2"BORE 1/2" KEY
SPRCKT,CAST,10T 50MM 2"BORE 1/2"
125
Operator's Manual MODEL 5640
126
Operator's Manual MODEL 5640
2 chain 3.5" roller under belt
Item #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
Quantity
4
1
1
1
1
4
1
1
1
2
2
2
4
2
4
4
5
10
14
8
6
6
1
2
2
4
1
1
1
Part #
195769
502771
502770
502650
173264
261793
174041
173266
173265
173263
174042
261792
H00493
H00492
352151
352153
171313
501900
351313
351309
351310
351316
175125
351311
019.00435
321584
321573
321576
321570
Description
ANTIWRAP,BOLT ON,WELDED,HARV-WIND-2010
BOLT,HEX,HD,5/8"-11UNC x 9-1/2" GR8
BOLT,HEX,HD,5/8"-11UNC x 8-1/2" GR8
BOLT,HEX,HD,5/8"-11UNC x 5-1/2 GR8
BRACKET DEFLECTOR STONE CTRBD RH 6140-05
DEFLECTOR RUBBER NOSE ROLLER CTR,SIDEBD
BRACKET DEFLECTOR STONE CTRBD RH 6140-05
BRACKET DEFLECTOR STONE RH 6140-2005
BRACKET,DEFLECTOR,STONE LH 6140-2005
BRACKET DEFLECTOR STONE QTRBD LH 6140-05
BRACKET DEFLECTOR STONE QTRBD RH
DEFLECTOR RUBBER QTRBRD
ROLLER PLT,PRIMARY AFT,2CHAIN 6140-2004
ROLLER PLT,PRIMARY FWD,2CHAIN 6140-2004
RLR,BC,ST,5/8X3.5X2.125X5FL,SC
RLR,BC,ST,5/8X3.5X2.375,SC
SPACER,NOSE,ROLLER,1/4"x5"ODx11/16"ID
COLLAR,SHAFT,SET,SCREW,5/8"
RLR,BC,PU,5/8X5X1,PC
STANDOFF,RLR,BC,5/8"x1-1/4"
STANDOFF,RLR,BC,5/8"x3-5/8"
RLR,BC,PU,5/8X3.5X2.375,PC
SPACER,NOSE,ROLLER,1/4"
RLR,BC,PU,5/8X3.5X2.375X5FL,PC
WINDING PROTECTION 5.250"
SPRCKT,CAST,10T 56MM 2"BORE 1/2"
SPRCKT,CAST,12T 42MM 2"BORE 1/2"
SPRCKT,CAST,12T 45MM 2"BORE 1/2" KEY
SPRCKT,CAST,10T 50MM 2"BORE 1/2"
127
Operator's Manual MODEL 5640
128
Operator's Manual MODEL 5640
2 chain roller under rods
Item #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
Quantity
4
4
2
4
4
14
6
2
6
2
8
6
1
2
2
4
1
1
1
1
1
1
Part #
195769
H00493
H00492
351315
351702
351313
351316
351311
171313
171309
351309
351310
175125
501900
019.00435
321584
321573
321576
321570
502308
502770
502337
Description
ANTIWRAP,BOLT ON,WELDED,HARV-WIND-2010
ROLLER PLT,PRIMARY AFT,2CHAIN 6140-2004
ROLLER PLT,PRIMARY FWD,2CHAIN 6140-2004
RLR,BC,ST,5/8X4X4.250,SC
RLR,BC,ST,5/8X4X3.25,SC
RLR,BC,PU,5/8X5X1,PC
RLR,BC,PU,5/8X3.5X2.375,PC
RLR,BC,PU,5/8X3.5X2.375X5FL,PC
SPACER,NOSE,ROLLER,1/4"x5"ODx11/16"ID
SPACER,NOSE,ROLLER,1/4"x2.5"ODx11/16"ID
STANDOFF,RLR,BC,5/8"x1-1/4"
STANDOFF,RLR,BC,5/8"x3-5/8"
SPACER,NOSE,ROLLER,1/4"
COLLAR,SHAFT,SET,SCREW,5/8"
WINDING PROTECTION 5.250"
SPRCKT,CAST,10T 56MM 2"BORE 1/2"
SPRCKT,CAST,12T 42MM 2"BORE 1/2"
SPRCKT,CAST,12T 45MM 2"BORE 1/2" KEY
SPRCKT,CAST,10T 50MM 2"BORE 1/2"
BOLT,HEX,HD,5/8"-11UNC x 12" *GR8*
BOLT,HEX,HD,5/8"-11UNC x 8-1/2" GR8
BOLT,HEX,HD,5/8"-11UNC x 7" **GR8**
129
Operator's Manual MODEL 5640
130
Operator's Manual MODEL 5640
4 chain 2.5" roller under belt
Item #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
Quantity
2
2
1
1
1
5
5
12
8
4
4
2
12
2
5
3
4
1
4
1
1
1
Part #
192025
192049
502303
501360
502766
195769
352280
351313
351316
351311
171309
171310
351310
171313
501900
171314
019.00435
175125
321584
321573
321576
321570
Description
DIVIDER DIGGERNOSE 4 WEB 6140/HARV-2004
WELD,UPPR DIVIDER 4 WEB 6400-2004
BOLT,HEX,HD,5/8"-11UNC x 7-1/2" GR 5
BOLT,HEX,HD,5/8"-11UNC x 6-1/2" GR 5
BOLT,HEX,HD,5/8"-11UNC x 4-1/2" GR8
ANTIWRAP,BOLT ON,WELDED,HARV-WIND-2010
RLR,BC,ST,5/8X2.5X2.375X4FL,SC
RLR,BC,PU,5/8X5X1,PC
RLR,BC,PU,5/8X3.5X2.375,PC
RLR,BC,PU,5/8X3.5X2.375X5FL,PC
SPACER,NOSE,ROLLER,1/4"x2.5"ODx11/16"ID
SPACER,NOSE,ROLLER,3/8"x2.5"ODx11/16"ID
STANDOFF,RLR,BC,5/8"x3-5/8"
SPACER,NOSE,ROLLER,1/4"x5"ODx11/16"ID
COLLAR,SHAFT,SET,SCREW,5/8"
SPACER,NOSE,ROLLER,3/8"x5"ODx11/16"ID
WINDING PROTECTION 5.250"
SPACER,NOSE,ROLLER,1/4"
SPRCKT,CAST,10T 56MM 2"BORE 1/2"
SPRCKT,CAST,12T 42MM 2"BORE 1/2"
SPRCKT,CAST,12T 45MM 2"BORE 1/2" KEY
SPRCKT,CAST,10T 50MM 2"BORE 1/2"
131
Operator's Manual MODEL 5640
132
Operator's Manual MODEL 5640
4 chain 3.5" roller under belt
Item #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
Quantity
2
2
5
1
4
2
2
2
1
1
1
1
1
1
8
12
8
4
10
5
13
12
1
4
4
1
1
1
Part #
192025
192049
195769
173266
261793
174129
261792
174130
173264
174041
173265
502771
502305
502650
352151
351313
351316
351311
171313
171314
501900
351310
175125
019.00435
321584
321573
321576
321570
Description
DIVIDER DIGGERNOSE 4 WEB 6140/HARV-2004
WELD,UPPR DIVIDER 4 WEB 6400-2004
ANTIWRAP,BOLT ON,WELDED,HARV-WIND-2010
BRACKET DEFLECTOR STONE RH 6140-2005
DEFLECTOR RUBBER NOSE ROLLER CTR,SIDEBD
BRACKET,DEFLECTR STONE CTRBD LH 4 CHN
DEFLECTOR RUBBER QTRBRD
BRACKET,DEFLECTR STONE CTRBD RH 4 CHN
BRACKET DEFLECTOR STONE CTRBD RH 6140-05
BRACKET DEFLECTOR STONE CTRBD RH 6140-05
BRACKET,DEFLECTOR,STONE LH 6140-2005
BOLT,HEX,HD,5/8"-11UNC x 9-1/2" GR8
BOLT,HEX,HD,5/8"-11UNC x 10" GR 5
BOLT,HEX,HD,5/8"-11UNC x 5-1/2 GR8
RLR,BC,ST,5/8X3.5X2.125X5FL,SC
RLR,BC,PU,5/8X5X1,PC
RLR,BC,PU,5/8X3.5X2.375,PC
RLR,BC,PU,5/8X3.5X2.375X5FL,PC
SPACER,NOSE,ROLLER,1/4"x5"ODx11/16"ID
SPACER,NOSE,ROLLER,3/8"x5"ODx11/16"ID
COLLAR,SHAFT,SET,SCREW,5/8"
STANDOFF,RLR,BC,5/8"x3-5/8"
SPACER,NOSE,ROLLER,1/4"
WINDING PROTECTION 5.250"
SPRCKT,CAST,10T 56MM 2"BORE 1/2"
SPRCKT,CAST,12T 42MM 2"BORE 1/2"
SPRCKT,CAST,12T 45MM 2"BORE 1/2" KEY
SPRCKT,CAST,10T 50MM 2"BORE 1/2"
133
Operator's Manual MODEL 5640
134
Operator's Manual MODEL 5640
4 chain roller under rods
Item #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
Quantity
2
2
5
12
8
4
5
1
1
1
4
3
3
4
3
12
4
1
5
4
1
1
1
Part #
192025
192049
351315
351313
351316
351311
195769
502459
502309
502337
171315
171313
171314
171311
171309
351310
019.00435
175125
501900
321584
321573
321576
321570
Description
DIVIDER DIGGERNOSE 4 WEB 6140/HARV-2004
WELD,UPPR DIVIDER 4 WEB 6400-2004
RLR,BC,ST,5/8X4X4.250,SC
RLR,BC,PU,5/8X5X1,PC
RLR,BC,PU,5/8X3.5X2.375,PC
RLR,BC,PU,5/8X3.5X2.375X5FL,PC
ANTIWRAP,BOLT ON,WELDED,HARV-WIND-2010
BOLT,HEX,HD,5/8"-11UNC x 14" *GR8*
BOLT,HEX,HD,5/8"-11UNC x 13" *GR8*
BOLT,HEX,HD,5/8"-11UNC x 7" **GR8**
SPACER,NOSE,ROLLER,1/2"x5"ODx11/16"ID
SPACER,NOSE,ROLLER,1/4"x5"ODx11/16"ID
SPACER,NOSE,ROLLER,3/8"x5"ODx11/16"ID
SPACER,NOSE,ROLLER,1/2"x3"ODx11/16"ID
SPACER,NOSE,ROLLER,1/4"x2.5"ODx11/16"ID
STANDOFF,RLR,BC,5/8"x3-5/8"
WINDING PROTECTION 5.250"
SPACER,NOSE,ROLLER,1/4"
COLLAR,SHAFT,SET,SCREW,5/8"
SPRCKT,CAST,10T 56MM 2"BORE 1/2"
SPRCKT,CAST,12T 42MM 2"BORE 1/2"
SPRCKT,CAST,12T 45MM 2"BORE 1/2" KEY
SPRCKT,CAST,10T 50MM 2"BORE 1/2"
135
Operator's Manual MODEL 5640
136
Operator's Manual MODEL 5640
4 chain kryptane rollers under rods
Item #
1
2
3
4
5
6
7
8
9
10
11
12
13
Quantity
2
2
5
2
1
5
12
8
4
12
3
2
4
Part #
192025
192049
195769
502422
502768
352804
351313
351316
351311
351310
171314
171313
019.00435
Description
DIVIDER DIGGERNOSE 4 WEB 6140/HARV-2004
WELD,UPPR DIVIDER 4 WEB 6400-2004
ANTIWRAP,BOLT ON,WELDED,HARV-WIND-2010
BOLT,HEX,HD,5/8"-11UNC x 9 *GR8*
BOLT,HEX,HD,5/8"-11UNC x 6" GR8
RLR,BLTD,CHN,NOSE,TAPERED BLUE,KRYTANE
RLR,BC,PU,5/8X5X1,PC
RLR,BC,PU,5/8X3.5X2.375,PC
RLR,BC,PU,5/8X3.5X2.375X5FL,PC
STANDOFF,RLR,BC,5/8"x3-5/8"
SPACER,NOSE,ROLLER,3/8"x5"ODx11/16"ID
SPACER,NOSE,ROLLER,1/4"x5"ODx11/16"ID
WINDING PROTECTION 5.250"
14
15
16
17
18
1
4
1
1
1
175125
321584
321573
321576
321570
SPACER,NOSE,ROLLER,1/4"
SPRCKT,CAST,10T 56MM 2"BORE 1/2"
SPRCKT,CAST,12T 42MM 2"BORE 1/2"
SPRCKT,CAST,12T 45MM 2"BORE 1/2" KEY
SPRCKT,CAST,10T 50MM 2"BORE 1/2"
137
Operator's Manual MODEL 5640
138
Operator's Manual MODEL 5640
Wide digging nose
Item #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Quantity
1
2
2
2
2
2
2
2
2
2
1
1
1
1
1
1
Part #
195005
352017
602616
195241
030087
030068
174663
351329
502319
501371
050041
351310
351252
173010
300099
080118
Description
SWINGFRAME,WIDE,5640-2008
CHAIN,DIGGER NOSE LIFT 42" OR 36 LINKS
CYL,2.50"x12",TIE ROD,22.25",1.125",3/4
ARM,CONTROL SHORT D NOSE HARV/6140-2009
WEAR PLATE,PRIMARY,HARV/WIND-2010
WEAR PLT TRANSITION SS 5640-2007
QUARTERBORD,REAR,PRIMARY,5640-2010
LINK,COUPLING,3/8"ALLOY,CHAIN,G-10-8
SCREW,FLAT,SCKT,HD,1/2"-13 x 1"
WASHER,FLAT,5/8" (SAE)
PIN,CENTER BOARD PIVOT 6140/6400
STANDOFF,RLR,BC,5/8"x3-5/8"
STANDOFF,RLR,BC,1/2"x1-7/8" #822
INDICATOR,DEPTH 6400/6140-2004
LABEL,DEPTH,INDICATOR (1 THRU 10)
DEPTH IND CONDUIT 1x40-1/2" LONG 6400-06
139
Operator's Manual MODEL 5640
140
Operator's Manual MODEL 5640
Narrow digging nose
Item #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
Quantity
1
2
2
2
2
2
1
6
2
2
1
2
2
1
2
1
1
1
1
Part #
195680
352017
602616
195241
351329
030087
030028
181549
261778
174663
030027
502319
501371
050041
351310
080118
351252
173010
300099
Description
SWINGFRAME,NARROW,31IN/31IN,5640-2008
CHAIN,DIGGER NOSE LIFT 42" OR 36 LINKS
CYL,2.50"x12",TIE ROD,22.25",1.125",3/4
ARM,CONTROL SHORT D NOSE HARV/6140-2009
LINK,COUPLING,3/8"ALLOY,CHAIN,G-10-8
WEAR PLATE,PRIMARY,HARV/WIND-2010
WEAR PLATE,LH NRW NOSE HARV-2004
SPACER,1"ODx.640IDx3"LONG MIDDLE
BELT,DIGGER NOSE DEFLECTOR
QUARTERBORD,REAR,PRIMARY,5640-2010
WEAR PLATE,RH NRW NOSE HARV-2004
SCREW,FLAT,SCKT,HD,1/2"-13 x 1"
WASHER,FLAT,5/8" (SAE)
PIN,CENTER BOARD PIVOT 6140/6400
STANDOFF,RLR,BC,5/8"x3-5/8"
DEPTH IND CONDUIT 1x40-1/2" LONG 6400-06
STANDOFF,RLR,BC,1/2"x1-7/8" #822
INDICATOR,DEPTH 6400/6140-2004
LABEL,DEPTH,INDICATOR (1 THRU 10)
141
Operator's Manual MODEL 5640
142
Operator's Manual MODEL 5640
Secondary
Item #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
Quantity
3
3
4
26
16
6
2
20
20
26
2
1
1
1
1
1
1
1
1
Part #
196970
196971
351306
351313
351311
351316
353043
171313
019.00435
351310
171381
030086
030085
030114
030115
321584
321573
321576
321570
Description
SCRAPER,5" FLNG RLLR,RH,BOLT TO SIDEWALL
SCRAPER,5" FLNG RLLR,LH,BOLT TO SIDEWALL
RLR,BC,PU,5/8X3.5X2.375X5FL,SC
RLR,BC,PU,5/8X5X1,PC
RLR,BC,PU,5/8X3.5X2.375X5FL,PC
RLR,BC,PU,5/8X3.5X2.375,PC
RLR,BC,PU,5/8X3.5X2.375,SC
SPACER,NOSE,ROLLER,1/4"x5"ODx11/16"ID
WINDING PROTECTION 5.250"
STANDOFF,RLR,BC,5/8"x3-5/8"
WEAR,PLATE,SECONDARY,SIDES,SS 5600
WEAR PLATE,SEC,RH,5640-2010
WEAR PLATE,SEC,LH,5640-2010
SS CNTR BRD,LH,BOLTABLE DRAWBAR,5640-11
SS CNTR BRD,RH,BOLTABLE DRAWBAR,5640-11
SPRCKT,CAST,10T 56MM 2"BORE 1/2"
SPRCKT,CAST,12T 42MM 2"BORE 1/2"
SPRCKT,CAST,12T 45MM 2"BORE 1/2" KEY
SPRCKT,CAST,10T 50MM 2"BORE 1/2"
143
Operator's Manual MODEL 5640
144
Operator's Manual MODEL 5640
Vine chain std parts
Item #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
Quantity
2
2
4
16
20
4
3
1
1
2
4
24
20
10
2
5
1
1
1
1
1
4
1
16
16
16
2
4
Part #
196971
196970
351306
352925
351311
351314
351317
352245
353042
175493
351309
171313
019.00435
501900
261781
321565
321644
321619
881184
881191
881336
881140
881173
501095
501269
781306
781309
781307
Description
SCRAPER,5" FLNG RLLR,LH,BOLT TO SIDEWALL
SCRAPER,5" FLNG RLLR,RH,BOLT TO SIDEWALL
RLR,BC,PU,5/8X3.5X2.375X5FL,SC
RLR,BC,PU,5/8X2.375X1.125,PC
RLR,BC,PU,5/8X3.5X2.375X5FL,PC
RLR,BC,PU,5/8X4X1,PC
RLR,BLTD,CHN,5/8"x3-1/2"&6" COMBO TEROG
RLR,BC,PU,5/8X4X1,SC
RLR,BC,PU,5/8X6X1,SC
BUSHING,SHAKER ROLLER,4IN TO 6IN,2013
STANDOFF,RLR,BC,5/8"x1-1/4"
SPACER,NOSE,ROLLER,1/4"x5"ODx11/16"ID
WINDING PROTECTION 5.250"
COLLAR,SHAFT,SET,SCREW,5/8"
BELT,BUCKLE,SECONDARY 6140
SPRCKT,CAST,12T 150MM PITCH 2"
SPRCKT,WELD,9T 100-200MM PITCH 61X0-08
SPRCKT,CAST,10T 90/180MM PITCH
SLIPCLUTCH,ASSY,80P48Tx2" BORE 8 BOLT
SPRCKT,H80BS23x1-3/4" BORE 3/8" KEYWAY
SPRCKT,H80BS26 x 1-3/4" BORE 3/8" KEYWAY
IDLER,80,PITCH,5/8" BORE 12 TOOTH #704
SPRCKT,H80BS16x2" BORE 1/2" KEYWAY
BOLT,HEX,HD,1/2"-13UNC x 3-1/2" GR 5
WASHER,FLAT,1/2" (SAE)ZINC PLATED(54/LB)
SPRING,SLIPCLUTCH,1-3/4"LONG,6 COIL
PLATE,SLIPCLUTCH,80P48T 11"OD x 4.365"ID
DISC,FRICTION,FIBER 9.10"ODx4.27"ID
145
Operator's Manual MODEL 5640
146
Operator's Manual MODEL 5640
Vine chain std parts
Item #
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
Quantity
2
2
2
1
1
4
1
2
4
1
1
1
1
1
2
Part #
781308
881199
231122
231120
881196
174664
050236
231115
231118
351957
351817
173037
981394
171451
173189
Description
HUB,SLIPCLUTCH,80P48T 9.1"OD x 2"ID
SPRCKT,80A48x4.265" BORE SLIPCLUTCH
BRNG,PB,1-3/4",ECC LOCK "R"SEAL WIDE
BRNG,4BOLT,FLNG,TCJ 2",ECC LOCK
IDLER,CHAIN,60/80PITCH ASSY 2868BD2X
ANTI-WRAP,VINE CHAIN,HARV-2010
SHFT,7K,2"x156.50" WIDE SEP SCNDRY
BRNG,INSERT,2",ECC,LOCK/SPHR
HOUSING,BRNG,4HOLE,100MM,FLANGETTE PLATD
ASSY,#80R RLR CHN x165" SCNDRY JACK 6400
ASSY,#80R RLR CHN x83" SEC 5600
PLATE,CHAIN GUIDE VINE CHAIN 6400
UHMW,VINE CHAIN GUIDE 1/2"x1.5"x10"LONG
ROLLER,VINE,CHN,OVER,RIDE 152-1/4"L HARV
SCRAPPER,DRUM,DEV 6400-2004
147
Operator's Manual MODEL 5640
148
Operator's Manual MODEL 5640
Brush roller
Item #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Quantity
1
2
1
2
1
1
4
2
2
2
1
1
2
1
2
1
2
1
1
1
Part #
196568
352017
171602
171454
181593
174527
351252
020820
171603
781057
821471
173205
231122
173098
173204
601753
171954
173206
821470
174528
Description
CENTER BOARD,BRUSHROLLER,5640-2011
CHAIN,DIGGER NOSE LIFT 42" OR 36 LINKS
ROLLER,BRUSH,WELDMENT,5640
SUPPORT,BEARING,MNT,BRUSH,ROLLER 5600
COUPLING,1-3/4"x1"x3-3/4" 1/4"&3/8" KEY
PLATE,REAR CROSS,RH,BRUSH ROLL,5640-2009
STANDOFF,RLR,BC,1/2"x1-7/8" #822
CHAIN ATTACH PLT BRSHROLL HARV-2004
PLATE,BRUSH,ROLL,END 10GA x 17"DIA 5600
BUSHING,Q1x1-3/4" BORE SPLIT TAPER
SHFT,DK,1-3/4"x21.25"(3-4.75)3/8"KEY
SUPT,BRUSH,ROLLER 6400-2004
BRNG,PB,1-3/4",ECC LOCK "R"SEAL WIDE
TORQUE ARM,BRUSH HYD DRV
SUPT,BRUSH,ROLLER 6400-2004
MTR,HY,6.0CUIN,1"KEY,SAE-A,TE-SERIES
EXTENSION,SECONDARY QTR BOARD 6400
SUPT,BRUSH,ROLLER LH 6400-2004
SHFT,DUMMY,1-3/4"x18-3/4" TAPERED END
PLATE,REAR CROSS,LH,BRUSH ROLL,5640-2009
149
Operator's Manual MODEL 5640
150
Operator's Manual MODEL 5640
Snapper roller
Item #
1
2
3
4
5
6
7
10
11
12
13
14
15
16
Quantity
2
2
2
1
4
4
4
8
4
4
1
2
2
2
Part #
171591
195683
192424
192450
352333
502410
981242
231113
231116
195682
174360
821921
171477
171462
Description
ROLLER,UPPER,SNAPPER 5625/5640
UNDERDRUM,VINE CHAIN,69IN,HARV-2010
ARM,SNAPPER ROLLER 6200-2004
FRAME,SNAPPER,ROLL AND CHOPPER 6400-2004
CHAIN SNAP ROLL HANGER 5/16"x18" 6400-05
BOLT,EYE,1/2" x 8" W/NUT *PLATED*
SPRING,ELIM,2-3/4"L x 1.250"OD .175 8COI
BRNG,INSERT,1-3/8",ECC,LOCK/SPHR
HOUSING,BRNG,3HOLE,72MM,FLANGETTE PLATED
MOUNT,UNDERDRUM,W/ANTIWRAP 6140-2010
SNAPROLL CNTER CLAMP HARV-2008
SHFT,DT,1-3/8"x69-15/16" DT 5/8"
AXLE,SNAPPER,ROLLER,LH 5100/5600
AXLE,SNAPPER,ROLLER,RH 5100/5600
151
Operator's Manual MODEL 5640
152
Operator's Manual MODEL 5640
Stripper kit
Item #
1
2
Quantity
1
1
Part #
602612
196481
Description
CYL,2.00"x8",TIE ROD,20.25",1.125",3/4
MOUNT,CYLINDER,HYD STRIPPER,5640-2011
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
22
23
24
25
26
27
28
29
30
31
32
2
2
2
4
4
2
2
6
60
2
1
2
1
4
6
1
24
16
16
60
60
2
4
4
4
4
2
1
2
192190
193384
195683
195682
192185
192186
192187
192184
076.04142
192188
502698
090265
173848
171807
174185
981670
181501
097.00021
031.00634
023.12251
099.00012
261781
173038
502699
181791
231113
821921
050009
501220
STRIPPER KIT MAIN SUPPORT
SCRAPPER,STRIPPER,KIT 6440-2005
UNDERDRUM,VINE CHAIN,69IN,HARV-2010
MOUNT,UNDERDRUM,W/ANTIWRAP 6140-2010
STRIPPER LINK,LH SHORT
STRIPPER LINK,RH LONG
HOLDER
HOLDER
BACK-HOLDING PLATE (SPRING WITH PADDLE)
STRIPPER LINK,LH LONG
BOLT,EYE,5/8"x5" THEADED 4-1/4"
TUBE
BAR,CLAMP,TANK,6400-2006
SPACER,CYL,SHKR,1/2"x1.13"IDx2.25"OD
PLATE,MOUNT,TURNBUCKLE,6160-2007
TURNBUCKLE,1-1/8SCREW,EXT 33" CLOSED 21"
NUBBIN,1"ODx1-1/4" LONG D 5/8"
SPRING, PULL
EYELET BOLT,10X145
ANGULAR BRKT STRAP
WASHER 13
BELT,BUCKLE,SECONDARY 6140
MOUNT,STRIPPER KIT HARV/6140-2004
ROD,END,3/4"x10" THEADED 9-1/8"
BUSHING,0.78"BOREx1-1/16"LGx1-1/4"OD4200
BRNG,INSERT,1-3/8",ECC,LOCK/SPHR
SHFT,DT,1-3/8"x69-15/16" DT 5/8"
PIN,DISC COULTER HYD CYL MOUNT
HAIRPIN,COTTER,3/16"x3-3/4" #21-08
153
Operator's Manual MODEL 5640
154
Operator's Manual MODEL 5640
Maindrive
Item #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
Quantity
1
1
1
1
2
2
2
1
1
5
3
1
9
2
2
2
2
8
8
8
1
2
1
1
1
1
1
2
Part #
571316
231399
050760
231163
571374
571377
571378
57.DC.4870.2
57.DC.4870
231120
881184
351812
881140
881166
821400
231115
321572
501095
501269
781306
781309
781307
781308
881199
352411
352530
351813
881331
Description
PTO BONDIOLI SZ8 1-3/4x1-3/4 20SPL TLOCK
BRNG,4 BOLT FLANGE,2"TAPERED SLEEVE LOCK
SHAFT,FRONT JACK,5640-2011
BRNG,4BOLT,FLNG,1-3/4"BORE ECCENTRIC LCK
COMPANION FLANGE RD 1.75ID EUROCARDAN
YOKE,FLANGE,END 150MM EUROCARDAN
CROSS,KIT 150MM EUROCARDAN
TUBE,SLIPSHAFT
SLIPSLEEVE
BRNG,4BOLT,FLNG,TCJ 2",ECC LOCK
SLIPCLUTCH,ASSY,80P48Tx2" BORE 8 BOLT
ASSY,#80R RLR CHN x129" 5600/5100
IDLER,80,PITCH,5/8" BORE 12 TOOTH #704
SPRCKT,H80BS13x1-3/8" BORE 5/16" KEYWAY
SHFT,TK,2"x80"(4.5-16.5-21.625) 1/2" KEY
BRNG,INSERT,2",ECC,LOCK/SPHR
HOUSING,BRNG,100MM,STL,TEARDROP,BHTD101
BOLT,HEX,HD,1/2"-13UNC x 3-1/2" GR 5
WASHER,FLAT,1/2" (SAE)ZINC PLATED(54/LB)
SPRING,SLIPCLUTCH,1-3/4"LONG,6 COIL
PLATE,SLIPCLUTCH,80P48T 11"OD x 4.365"ID
DISC,FRICTION,FIBER 9.10"ODx4.27"ID
HUB,SLIPCLUTCH,80P48T 9.1"OD x 2"ID
SPRCKT,80A48x4.265" BORE SLIPCLUTCH
CHN,RLR,80 PITCH X 97 INCHES
CHN,RLR,80Px173" OVERIDE RLLR WCS 6400
ASSY,#80R RLR CHN x103" SEC JACK 5100
SPRCKT,H80BS30 x 2" BORE 1/2" KEYWAY
155
Operator's Manual MODEL 5640
156
Operator's Manual MODEL 5640
Maindrive
Item #
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
Quantity
1
1
2
1
4
1
1
2
2
2
1
1
1
1
1
1
1
1
1
4
2
Part #
821398
050236
351802
881384
351309
881168
821989
231119
502711
571220
571387
781282
781513
821990
881164
351955
881182
571152
35.89.0023
231118
231127
Description
SHFT,SK,2"x20-1/2" (7.5) 1/2" KEY
SHFT,7K,2"x156.50" WIDE SEP SCNDRY
STANDOFF,RLR,BC,5/8"x2-3/4" #825
RLR,IDLR,CHAIN,RB,60/80P,5/8X2.5X2.25,SC
STANDOFF,RLR,BC,5/8"x1-1/4"
SPRCKT,H80BS14x1-3/8" BORE 5/16" KEYWAY
SHAFT,DK,1-3/8"x77-1/2"
BRNG,4BOLT,FLNG,1-3/8" ECC LOCK "R"
COLLAR,SHAFT,CLAMP ON,1-3/8"
ASSY,YOKE,2500S,1.75"x1.375 3/8"x5/16"K
GRBX,BEVEL,4WAY,1:186,60HP @1000 RPM
BUSHING,SFx1-3/4" BORE
SHEAVE,4GROOVE,B,20"xQD BUSHING BORE
SHAFT,DK,1-3/8"x45.470
SPRCKT,H80BS12x1-3/8" BORE 5/16" KEYWAY
ASSY,#80R RLR CHN x73" SE DRIVE 6400
SPRCKT,H80BS30x1-3/8" BORE 5/16" KEYWAY
GRBX,BEVEL,3WAY,1:1,71HP @540 RPM
CHAIN,73" SIDE ELEVATOR DRIVE
HOUSING,BRNG,4HOLE,100MM,FLANGETTE PLATD
BRNG,INSERT,2",ECC,LOCK/SPHR OD
157
Operator's Manual MODEL 5640
158
Operator's Manual MODEL 5640
Hydraulics
Item #
1
2
3
4
5
6
7
8
9
10
11
Quantity
1
11
1
1
1
1
1
2
1
24
2
Part #
601643
601651
300187
300188
300189
300190
173095
601639
602097
601338
601637
Description
CARTRIDGE E/H,2W 2P,10-2,12VDC,N.O.,POP
VALVE ASSY,4W 3P,D03,FLOAT,12VDC
DECAL,RH LEVELING (FOR VALVE HANDLE)
DECAL,LH LEVELING (FOR VALVE HANDLE)
DECAL,R/S TABLE SPACING (VALVE HANDLE)
DECAL,R/S TABLE ANGLE (FOR VALVE HANDLE)
SHEET,HYD VALV BRCKT HARV-2004
MANIFOLD,2,STATION,4"x4"x5-1/2"NO VALVES
*MANIFOLD,ASSEMBLY,7,STATION,W/5 VALVES
CPLG,HYD,STR,6400-6-6 (6MJ-6MB)
CPLG,HYD,90DEG,6801-8-10 (8MJ-10MB)
159
Operator's Manual MODEL 5640
160
Operator's Manual MODEL 5640
Rear cross standard parts
Item #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
Quantity
1
1
2
1
1
1
1
1
3
1
1
1
2
1
1
1
1
2
8
31
31
1
2
4
2
6
2
4
Part #
571180
571179
981593
194962
841145
050682
821393
821388
231121
881181
262086
174075
175543
174074
172956
173480
173772
351316
351312
351314
351309
175168
352245
501900
175551
351311
019.00435
352934
Description
YOKE,ASSY,1200S,1-3/8"x1-3/8" 5/16"KEY
YOKE,ASSY,1200S,1-3/8"x1-3/8" SLIP 5/16"
LINK,TOP,5/8" HOLE x 11" LONG
FRAME,REAR CROSS 5640-2008
SHLD,DRIVE,SHAFT,5640 2"TO4"x54-3/4" ABS
SHFT,DK,1-3/8"x45-3/8 (2.25-2.5).313
SHFT,DK,1-3/8"x58.5"(2.25-2.5)5/16"90DEG
SHFT,DK,1-3/8"x13" (2-2) 5/16" KEY
BRNG,PB,1-3/8",ECC LOCK "R"SEAL WIDE
SPRCKT,H80BS22x1-3/8" BORE 5/16" KEYWAY
COVER,R-CROSS,NO EARS,SPREADERRLLR,5640
SHLD REARCROSS LH SIDE 5640-2007
COVER,TOP,REAR CROSS,CHAIN W/EAR,5640-12
SHLD REARCROSS RH SIDE 5640-2007
REARCROSS SIDEELEV DEFLECTR HARV-2004
PLATE,TENSION,FRONT,RC 6440-2005
PLATE,TENSION,REAR,RC 6440-2005
RLR,BC,PU,5/8X3.5X2.375,PC
RLR,BC,PU,5/8X3.5X2.125X8FL,SC
RLR,BC,PU,5/8X4X1,PC
STANDOFF,RLR,BC,5/8"x1-1/4"
SCRAPER,ROLLER,8" FLANGE,RH
RLR,BC,PU,5/8X4X1,SC
COLLAR,SHAFT,SET,SCREW,5/8"
SCRAPER,REAR CROSS FRONT,HARV-2012
RLR,BC,PU,5/8X3.5X2.375X5FL,PC
WINDING PROTECTION 5.250"
STANDOFF,RLR,BC,5/8"x1-3/4" #783
161
Operator's Manual MODEL 5640
162
Operator's Manual MODEL 5640
Rear cross chain extension
Item #
1
2
3
4
5
6
7
8
9
10
11
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
Quantity
1
1
2
2
1
1
1
1
1
1
3
1
1
1
1
1
1
1
2
2
1
1
2
4
2
2
12
12
1
Part #
881183
321575
321567
321569
321571
231113
821391
172968
173013
981690
981246.2
501243
502646
B94.01675
173327
231121
174485
195119
019.00300
019.00487
881140
352255
881198
781303
781304
781305
781306
501095
195118
Description
SLIPCLUTCH,ASSY,80P30Tx1-3/8"BORE 6 BOLT
SPRCKT,CAST,10T 42MM 1-3/8"BORE
SPRCKT,CAST,10T 45MM 1-3/8"BORE 5/16"KEY
SPRCKT,CAST,8T 50MM 1-3/8"BORE 5/16" KEY
HOUSING,BRNG,72MM,STEEL,TEARDROP BHTD720
BRNG,INSERT,1-3/8",ECC,LOCK/SPHR
SHFT,QK,1-3/8"x52"(3-5-4.5-3)5/16"
PLATE,BRACKET
DEFLECTOR,REAR CROSS EXTN
FLAP,HOPPER,WEBEXT 6400-2004
LATCH,FLEXIBLE,DRAW,LARGE 35R
BOLT,CARRIAGE,5/16"-18UNC x 1" GR 2
COLLAR,SHAFT,SET,SCREW,1-3/8"
SENSOR,PROXIMITY,M18,NAMUR
SENSOR MOUNT,REAR CROSS HARV-2005
BRNG,PB,1-3/8",ECC LOCK "R"SEAL WIDE
SHIELD,REAR X EXT CHN DRIVE,TOP,HARV-09
MOUNT,REAR CROSS SHAFT,5640-2008
HINGE,3"
HINGE,1-15/16"
IDLER,80,PITCH,5/8" BORE 12 TOOTH #704
ASSY,#80R RLR CHNx81R-CROSS TXFR HARV-04
SPRCKT,80A30x3.010" BORE SLIPCLUTCH
DISC,FRICTION,FIBER 6-5/8"OD x 3"ID CF66
HUB,SLIPCLUTCH,80P30T 6.6"OD x 1-3/8"ID
PLATE,SLIPCLUTCH,80P30T 8"OD x 3.050"ID
SPRING,SLIPCLUTCH,1-3/4"LONG,6 COIL
BOLT,HEX,HD,1/2"-13UNC x 3-1/2" GR 5
SHIELD,REAR CROSS SHAFT MOUNT,5640-2008
163
Operator's Manual MODEL 5640
164
Operator's Manual MODEL 5640
2 spreader rolls
Item #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
Quantity
1
1
1
1
1
1
1
1
1
1
1
1
1
3
1
2
2
1
1
1
3
3
1
1
25
1
1
4
Part #
881183
192139
021061
F00603
F00603
173011
981246
173328
174494
981685
195321
174496
981710
981311
321575
321567
321569
231113
172955
321571
502319
501908
172954
821391
981294
821384
821383
231135
Description
SLIPCLUTCH,ASSY,80P30Tx1-3/8"BORE 6 BOLT
WELD,REAR CROSS TRNFR ROLLER 6400-2004
PLATE
HINGE
HINGE
SHILD,RCROSS SPDRDR ROLLS 6400-2004
LATCH,FLEXIBLE,DRAW,LARGE 35R
DEFLECTOR,RCROSS HOPPER HARV-2005
COVER,TOP,LH,REAR CROSS W EAR,6400-09
UHMW short.1.1
UHMW RCROSS LH SHORT 6400-2004
COVER,TOP,LH,REAR CROSS W EAR,HARV-09
FLAP,RUBBER,LONG RCROSS SPRDROLL
ROLL,RUBBER,12 POINT,1-1/4"B RECESSED RH
SPRCKT,CAST,10T 42MM 1-3/8"BORE
SPRCKT,CAST,10T 45MM 1-3/8"BORE 5/16"KEY
SPRCKT,CAST,8T 50MM 1-3/8"BORE 5/16" KEY
BRNG,INSERT,1-3/8",ECC,LOCK/SPHR
PLATE,SUPPORT ARM SHORT 6400-2004
HOUSING,BRNG,72MM,STEEL,TEARDROP BHTD720
SCREW,FLAT,SCKT,HD,1/2"-13 x 1"
WASHER,FLAT,3/4" USS ZINC PLT (9/LB)
PLATE,SUPPORT ARM LONG 6400-2004
SHFT,QK,1-3/8"x52"(3-5-4.5-3)5/16"
ROLL,RUBBER,FINGER,12POINT,1-1/4"BORE"A"
SHFT,SQ,HARV,1-1/4"SQ x 32" FNGR STB
SHFT,SQ,HARV,1-1/4"SQ x 20-1/2" FNGR STB
BRNG,2BOLT,FLNG,1-1/4" BORE
165
Operator's Manual MODEL 5640
166
Operator's Manual MODEL 5640
2 spreader rolls
Item #
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
Quantity
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
2
4
2
2
12
12
Part #
981229
501911
501950
881107
173327
B94.01675
502646
501243
881079
351827
231121
981682
173163
351819
881140
881198
781303
781304
781305
781306
501095
Description
ROLL,RUBBER,SPACER,1/2" x 1-1/4" SQ BORE
WASHER,FLAT,1-1/4" USS ZINC PLT (4/LB)
COLLAR,SHAFT,SET,SCREW,1-1/4"
SPRCKT,H60BS14x1-1/4" BORE 1/4" KEYWAY
SENSOR MOUNT,REAR CROSS HARV-2005
SENSOR,PROXIMITY,M18,NAMUR
COLLAR,SHAFT,SET,SCREW,1-3/8"
BOLT,CARRIAGE,5/16"-18UNC x 1" GR 2
IDLER,60,PITCH,5/8" BORE 15 TOOTH #709
ASSY,#60 RLR CHN x38-1/4"SPDR ROLLS 5600
BRNG,PB,1-3/8",ECC LOCK "R"SEAL WIDE
UHMW,TXFR ROLL ADJUST HARV-2004
CHAIN ADJUST,TXFR ROLL HARV-2004
ASSY,#80R RLR CHN x65" R-CROSS 5600
IDLER,80,PITCH,5/8" BORE 12 TOOTH #704
SPRCKT,80A30x3.010" BORE SLIPCLUTCH
DISC,FRICTION,FIBER 6-5/8"OD x 3"ID CF66
HUB,SLIPCLUTCH,80P30T 6.6"OD x 1-3/8"ID
PLATE,SLIPCLUTCH,80P30T 8"OD x 3.050"ID
SPRING,SLIPCLUTCH,1-3/4"LONG,6 COIL
BOLT,HEX,HD,1/2"-13UNC x 3-1/2" GR 5
167
Operator's Manual MODEL 5640
168
Operator's Manual MODEL 5640
3 spreader rolls
Item #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
Quantity
1
1
1
1
1
2
2
1
1
1
1
1
3
3
54
1
1
1
1
3
6
1
1
1
1
1
1
1
Part #
881183
192139
192265
981246
321575
321567
321569
231113
172955
321571
172954
821391
502319
501908
981294
821385
821384
821383
981229
501950
231135
174496
195321
981710
174494
981685
173328
173011
Description
SLIPCLUTCH,ASSY,80P30Tx1-3/8"BORE 6 BOLT
WELD,REAR CROSS TRNFR ROLLER 6400-2004
MOUNT,SHIELD SPRD ROLL 6400-2004
LATCH,FLEXIBLE,DRAW,LARGE 35R
SPRCKT,CAST,10T 42MM 1-3/8"BORE
SPRCKT,CAST,10T 45MM 1-3/8"BORE 5/16"KEY
SPRCKT,CAST,8T 50MM 1-3/8"BORE 5/16" KEY
BRNG,INSERT,1-3/8",ECC,LOCK/SPHR
PLATE,SUPPORT ARM SHORT 6400-2004
HOUSING,BRNG,72MM,STEEL,TEARDROP BHTD720
PLATE,SUPPORT ARM LONG 6400-2004
SHFT,QK,1-3/8"x52"(3-5-4.5-3)5/16"
SCREW,FLAT,SCKT,HD,1/2"-13 x 1"
WASHER,FLAT,3/4" USS ZINC PLT (9/LB)
ROLL,RUBBER,FINGER,12POINT,1-1/4"BORE"A"
SHFT,SQ,HARV,1-1/4"SQ x 41-1/2" FNGR STB
SHFT,SQ,HARV,1-1/4"SQ x 32" FNGR STB
SHFT,SQ,HARV,1-1/4"SQ x 20-1/2" FNGR STB
ROLL,RUBBER,SPACER,1/2" x 1-1/4" SQ BORE
COLLAR,SHAFT,SET,SCREW,1-1/4"
BRNG,2BOLT,FLNG,1-1/4" BORE
COVER,TOP,LH,REAR CROSS W EAR,HARV-09
PANEL,REAR,LH,RC W EARS,DRIVE,HARV-09
FLAP,RUBBER,LONG RCROSS SPRDROLL
COVER,TOP,LH,REAR CROSS W EAR,6400-09
UHMW RCROSS LH SHORT 6400-2004
DEFLECTOR,RCROSS HOPPER HARV-2005
SHILD,RCROSS SPDRDR ROLLS 6400-2004
169
Operator's Manual MODEL 5640
170
Operator's Manual MODEL 5640
3 spreader rolls
Item #
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
Quantity
1
4
1
1
1
1
1
1
1
1
1
1
2
4
2
2
12
12
Part #
881079
881107
881140
501243
502646
173327
B94.01675
352275
981682
173163
231121
351819
881198
781303
781304
781305
781306
501095
Description
IDLER,60,PITCH,5/8" BORE 15 TOOTH #709
SPRCKT,H60BS14x1-1/4" BORE 1/4" KEYWAY
IDLER,80,PITCH,5/8" BORE 12 TOOTH #704
BOLT,CARRIAGE,5/16"-18UNC x 1" GR 2
COLLAR,SHAFT,SET,SCREW,1-3/8"
SENSOR MOUNT,REAR CROSS HARV-2005
SENSOR,PROXIMITY,M18,NAMUR
CHN,RLR,60 PITCH x 35-7/8"
UHMW,TXFR ROLL ADJUST HARV-2004
CHAIN ADJUST,TXFR ROLL HARV-2004
BRNG,PB,1-3/8",ECC LOCK "R"SEAL WIDE
ASSY,#80R RLR CHN x65" R-CROSS 5600
SPRCKT,80A30x3.010" BORE SLIPCLUTCH
DISC,FRICTION,FIBER 6-5/8"OD x 3"ID CF66
HUB,SLIPCLUTCH,80P30T 6.6"OD x 1-3/8"ID
PLATE,SLIPCLUTCH,80P30T 8"OD x 3.050"ID
SPRING,SLIPCLUTCH,1-3/4"LONG,6 COIL
BOLT,HEX,HD,1/2"-13UNC x 3-1/2" GR 5
171
Operator's Manual MODEL 5640
172
Operator's Manual MODEL 5640
Side elevator
Item #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Quantity
1
1
1
1
4
2
18
18
2
2
1
1
1
1
1
1
2
1
1
1
Part #
196069
192205
981593
192255
351316
352221
351314
351309
351311
019.00435
351312
172990
501900
502698
174969
171404
181501
196979
981709
351310
Description
SIDE,ELEVATOR FRAME,BOOM,30",BACK
HOPPER FRAME,SIDE ELEV HARV 2004
LINK,TOP,5/8" HOLE x 11" LONG
STOP BAR,SIDE ELEV 6400-2004
RLR,BC,PU,5/8X3.5X2.375,PC
RLR,BC,PU,5/8X8X1.125,SC
RLR,BC,PU,5/8X4X1,PC
STANDOFF,RLR,BC,5/8"x1-1/4"
RLR,BC,PU,5/8X3.5X2.375X5FL,PC
WINDING PROTECTION 5.250"
RLR,BC,PU,5/8X3.5X2.125X8FL,SC
SIDE ELEV MOUNT BRCKT HARV-2004
COLLAR,SHAFT,SET,SCREW,5/8"
BOLT,EYE,5/8"x5" THEADED 4-1/4"
SIDE ELEVATOR BAR,HARV-2011
ADJUSTER,SIDE ELEV HARV-2004
NUBBIN,1"ODx1-1/4" LONG D 5/8"
SCRAPPER,8IN FLNG RLLR,LH,BOLT TO WALL
PVC PIPE SIDELEV STOP HARV-2005
STANDOFF,RLR,BC,5/8"x3-5/8"
173
Operator's Manual MODEL 5640
174
Operator's Manual MODEL 5640
Side elevator chain extension
Item #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
Quantity
1
1
1
1
1
2
1
1
6
6
1
1
2
1
2
1
1
1
12
12
12
2
4
2
2
1
1
1
Part #
196588
196067
881183
981670
821477
351306
262091
175145
351309
351314
351316
173036
231121
821392
501900
351821
881140
881172
501095
501269
781306
781305
781303
781304
881198
321569
321567
321575
Description
EXTENSION,SIDE ELEVATOR,5640-2011
FRONT,SUPPORT,STAR TABLE,5640-2010
SLIPCLUTCH,ASSY,80P30Tx1-3/8"BORE 6 BOLT
TURNBUCKLE,1-1/8SCREW,EXT 33" CLOSED 21"
SHFT,DT,1-1/4"x37-3/8" DT 5/8"
RLR,BC,PU,5/8X3.5X2.375X5FL,SC
RUBBER,TRANSITION
SIDEPANEL,SIDE ELEVATOR,EXTENSION
STANDOFF,RLR,BC,5/8"x1-1/4"
RLR,BC,PU,5/8X4X1,PC
RLR,BC,PU,5/8X3.5X2.375,PC
SHLD,SIDEEV,WEDEXT 6400-2004
BRNG,PB,1-3/8",ECC LOCK "R"SEAL WIDE
SHFT,DK,1-3/8"x56"(14.625-19.75).3125KEY
COLLAR,SHAFT,SET,SCREW,5/8"
ASSY,#80R RLR CHN x77" VC ROLLER 5600
IDLER,80,PITCH,5/8" BORE 12 TOOTH #704
SPRCKT,H80BS16x1-3/8" BORE 5/16" KEYWAY
BOLT,HEX,HD,1/2"-13UNC x 3-1/2" GR 5
WASHER,FLAT,1/2" (SAE)ZINC PLATED(54/LB)
SPRING,SLIPCLUTCH,1-3/4"LONG,6 COIL
PLATE,SLIPCLUTCH,80P30T 8"OD x 3.050"ID
DISC,FRICTION,FIBER 6-5/8"OD x 3"ID CF66
HUB,SLIPCLUTCH,80P30T 6.6"OD x 1-3/8"ID
SPRCKT,80A30x3.010" BORE SLIPCLUTCH
SPRCKT,CAST,8T 50MM 1-3/8"BORE 5/16" KEY
SPRCKT,CAST,10T 45MM 1-3/8"BORE 5/16"KEY
SPRCKT,CAST,10T 42MM 1-3/8"BORE
175
Operator's Manual MODEL 5640
176
Operator's Manual MODEL 5640
Separator side elevator parts
Item #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
Quantity
1
1
1
1
1
2
2
12
12
12
2
2
4
2
1
1
1
2
2
1
2
1
1
1
1
Part #
196067
196066
196065
881183
821477
351306
174364
501095
501269
781306
781305
781304
781303
881198
351811
881172
881140
175053
231121
821392
351316
881186
321569
321567
321575
Description
FRONT,SUPPORT,STAR TABLE,5640-2010
TIPOUT,SIDE ELEVATOR,RH,5640-2010
TIPOUT,SIDE ELEVATOR,5640-2010
SLIPCLUTCH,ASSY,80P30Tx1-3/8"BORE 6 BOLT
SHFT,DT,1-1/4"x37-3/8" DT 5/8"
RLR,BC,PU,5/8X3.5X2.375X5FL,SC
SUPPORT,STAR TABLE,REAR
BOLT,HEX,HD,1/2"-13UNC x 3-1/2" GR 5
WASHER,FLAT,1/2" (SAE)ZINC PLATED(54/LB)
SPRING,SLIPCLUTCH,1-3/4"LONG,6 COIL
PLATE,SLIPCLUTCH,80P30T 8"OD x 3.050"ID
HUB,SLIPCLUTCH,80P30T 6.6"OD x 1-3/8"ID
DISC,FRICTION,FIBER 6-5/8"OD x 3"ID CF66
SPRCKT,80A30x3.010" BORE SLIPCLUTCH
ASSY,#80R RLR CHN x75" 5600/5100
SPRCKT,H80BS16x1-3/8" BORE 5/16" KEYWAY
IDLER,80,PITCH,5/8" BORE 12 TOOTH #704
MOUNT,BOLT ON BOOM CATWALK,5640-2011
BRNG,PB,1-3/8",ECC LOCK "R"SEAL WIDE
SHFT,DK,1-3/8"x56"(14.625-19.75).3125KEY
RLR,BC,PU,5/8X3.5X2.375,PC
SPRCKT,H60BS16x1-3/8" BORE 5/16" KEYWAY
SPRCKT,CAST,8T 50MM 1-3/8"BORE 5/16" KEY
SPRCKT,CAST,10T 45MM 1-3/8"BORE 5/16"KEY
SPRCKT,CAST,10T 42MM 1-3/8"BORE
177
Operator's Manual MODEL 5640
178
Operator's Manual MODEL 5640
Eliminator table
Item #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
Quantity
1
1
1
2
1
16
1
1
2
2
26
1
2
16
1
1
1
1
1
16
2
2
2
1
6
1
1
1
1
1
1
1
Part #
196397
196398
982253
982000
196396
171326
171553
171552
019.00487
019.00300
231135
351826
881079
881107
351827
352879
881195
982254
197308
981270
194981
175131
501817
F01086
171778
981670
262090
175050
175051
351823
F01085
881081
Description
SHIELD,FINGER ROLL TABLE,5640-2011
SHIELD,SPREADER ROLLER,5640-2011
LEVER LATCH,SOUTHCO
SPRING,GAS,7.87STROKE,75# FORCE,M8THREAD
FRAME,FINGER ROLL TABLE,5640-2011
MOUNT,ELIM,BEARING,UNIVERSAL
GUIDE,CHAIN,ELIM,TABLE,44" LONG 5600
GUIDE,CHAIN,ELIM,TABLE,18" LONG 5600
HINGE,1-15/16"
HINGE,3"
BRNG,2BOLT,FLNG,1-1/4" BORE
ASSY,#60 RLR CHN x56-1/4 ELIM TBL CANT
IDLER,60,PITCH,5/8" BORE 15 TOOTH #709
SPRCKT,H60BS14x1-1/4" BORE 1/4" KEYWAY
ASSY,#60 RLR CHN x38-1/4"SPDR ROLLS 5600
ASSY,#80R RLR CHN x 140"
IDLER,CHAIN,50/60PTCH,3.5"x1/5"x5/8"#881
BUMPER,RUBBER,3/4"DIAx1/2" HIGH 10-24
BRACKET,LATCH,STAR TABLE SHIELD,5640-12
SPRING,ELIM,3.1"L x 1.64"D .218 7.75COIL
ROD,ADJUSTMENT,ROLLERS,HARV-2008
ADJUSTER,TUBE,STAR TABLE,HARV,2011
NUT,HEX,1"-8UNC
UHMW,CHAIN,GUIDE 1-1/2" x 18"
ADJUSTER,CHAIN GUIDE 5600
TURNBUCKLE,1-1/8SCREW,EXT 33" CLOSED 21"
RUBBER,TRANSITION RINGER TABLE BOOM 5640
SIDE PANEL,LH,FINGER ROLL TABLE,5640-11
SIDE PANEL,RH,FINGER ROLL TABLE,5640-11
ASSY,#60 RLR CHN x104-1/4" ELIM TBL RLR
UHMW,CHAIN,GUIDE 1-1/2" x44"
IDLER,60,PITCH,HEAVY DUTY 1" BORE 14T
179
Operator's Manual MODEL 5640
180
Operator's Manual MODEL 5640
Finger roll parts
Item #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Quantity
4
4
1
1
1
1
1
2
2
2
10
2
7
187
4
6
25
28
Part #
821559
821560
821558
821557
821494
821493
821492
821383
821384
821385
821172
821449
981236
981091
981292
981235
501950
981229
Description
SHFT,HARV,48"HALF FNGR FNGR W/O BRG&SPK
SHFT,HARV,48"WHOLE FNGR W/O BRG&SPK
SHFT,HARV,48" JACK FNGR FNGR W/O BRG&SPK
SHFT,HARV,48" DRV FNGR FNGR W/O BRG&SPK
SHFT,HARV,41-1/2",FNGR,W/O BRG&SPK
SHFT,HARV,32",FNGR,W/O BRG&SPK
SHFT,HARV,20-1/2",FNGR,W/O BRG&SPK
SHFT,SQ,HARV,1-1/4"SQ x 20-1/2" FNGR STB
SHFT,SQ,HARV,1-1/4"SQ x 32" FNGR STB
SHFT,SQ,HARV,1-1/4"SQ x 41-1/2" FNGR STB
SHFT,SQ,48",ELIM,1-1/4"x46-1/4" FITS ALL
SHFT,SQ,48",HARV,1-1/4"x46-1/4"JACK SHFT
ROLL,RUBBER,FINGER,LH,1-1/4"BR 2-1/4"HUB
ROLL,RUBBER,FINGER,1-1/4"BR STD2-3/4"HUB
ROLL,RUBBER,FINGER,1-1/4" BR RECESSED RH
ROLL,RUBBER,FINGER,RH 1-1/4"BR 2-1/4"HUB
COLLAR,SHAFT,SET,SCREW,1-1/4"
ROLL,RUBBER,SPACER,1/2" x 1-1/4" SQ BORE
181
Operator's Manual MODEL 5640
182
Operator's Manual MODEL 5640
Euroroll parts
Item #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
Quantity
4
4
1
1
1
1
1
2
2
2
10
2
202
123
100
94
4
25
Part #
821567
821566
821565
821564
821563
821562
821561
821383
821384
821385
821172
821449
981294
981296
981295
981297
981311
501950
Description
SHFT,HARV,48" EURO 6 FNGR W/O BRG&SPK
SHFT,HARV,48"EURO 12 FNGR W/O BRG&SPK
SHFT,HARV,48"JACK EURO FNGR W/O BRG&SPK
SHFT,HARV,48" DRV EURO FNGR W/O BRG&SPK
SHFT,HARV,41-1/2" EURO FNGR W/O BRG&SPK
SHFT,HARV,32" EURO FNGR W/O BRG&SPK
SHFT,HARV,20-1/2" EURO FNGR W/O BRG&SP
SHFT,SQ,HARV,1-1/4"SQ x 20-1/2" FNGR STB
SHFT,SQ,HARV,1-1/4"SQ x 32" FNGR STB
SHFT,SQ,HARV,1-1/4"SQ x 41-1/2" FNGR STB
SHFT,SQ,48",ELIM,1-1/4"x46-1/4" FITS ALL
SHFT,SQ,48",HARV,1-1/4"x46-1/4"JACK SHFT
ROLL,RUBBER,FINGER,12POINT,1-1/4"BORE"A"
ROLL,RUBBER,SPACER,3/8" x 1-1/4" SQ BORE
ROLL,RUBBER,FINGER,6,POINT,1-1/4"BORE
ROLL,RUBBER,SPACER,1-1/2"x1-1/4"SQ BORE
ROLL,RUBBER,12 POINT,1-1/4"B RECESSED RH
COLLAR,SHAFT,SET,SCREW,1-1/4"
183
Operator's Manual MODEL 5640
184
Operator's Manual MODEL 5640
Eliminator table kryptane roller option
Item #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Quantity
4
4
1
1
1
1
1
2
10
2
2
2
7
165
9
25
24
Part #
822012
822011
822010
822009
822013
822014
822015
821449
821172
821385
821384
821383
982343
982342
982344
981229
501950
Description
SHFT,HARV,48IN WHOLE KRPTANE FNGR
SHFT,HARV,48IN HALF KRPTANE FNGR
SHFT,HARV,48IN JACK SHAFT KRPTANE FNGR
SHFT,HARV,48IN DRV SHAFT KRPTANE FNGR
SHFT,HARV,41-1/2IN KRPTANE FNGR
SHFT,HARV,32IN KRPTANE FNGR
SHFT,HARV,20-1/2IN KRPTANE FNGR
SHFT,SQ,48",HARV,1-1/4"x46-1/4"JACK SHFT
SHFT,SQ,48",ELIM,1-1/4"x46-1/4" FITS ALL
SHFT,SQ,HARV,1-1/4"SQ x 41-1/2" FNGR STB
SHFT,SQ,HARV,1-1/4"SQ x 32" FNGR STB
SHFT,SQ,HARV,1-1/4"SQ x 20-1/2" FNGR STB
ROLL,6 POINT,PU,1.25BORE,KRYPTANE,LH OFS
ROLL,6 POINT,PU,1-1/4" BORE,KRYPTANE
ROLL,6 POINT,PU,1.25BORE,KRYPTANE,RH OFS
ROLL,RUBBER,SPACER,1/2" x 1-1/4" SQ BORE
COLLAR,SHAFT,SET,SCREW,1-1/4"
185
Operator's Manual MODEL 5640
186
Operator's Manual MODEL 5640
36" picking table
Item #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
Quantity
1
2
1
1
1
1
1
1
1
1
1
2
1
1
2
2
2
4
8
22
2
2
2
22
2
Part #
196408
191879
181643
192144
192143
571152
601657
172898
174771
174770
602623
231121
821389
321567
321569
321575
050038
351316
351311
351314
352221
352245
352252
351309
501900
Description
FRAME,36" PICKING TABLE,5640-2011
PIN,PIVOT P.T. EXT
COUPLING,1-3/8"x1"x3-3/4" 1/4"&5/16 KEY
EXTENSION,LH 36" 6400-2004
EXTENSION,RH 36" 6400-2004
GRBX,BEVEL,3WAY,1:1,71HP @540 RPM
MTR,HY,10.3CUIN,1"KEY,6-HOLE,TF-SERIES
HYDRAULIC MTR MNT 36 & 42IN BOOM HARV-04
ADD ON PANEL,REAR,36IN BOOM,6XX0-2010
ADD ON PANEL,FRONT,36IN BOOM,6XX0-2010
CYL,3.00"x24",TIE ROD,34.25",1.375",3/4
BRNG,PB,1-3/8",ECC LOCK "R"SEAL WIDE
SHFT,TK,1-3/8"x44-1/4"(3-5-4) 5/16"
SPRCKT,CAST,10T 45MM 1-3/8"BORE 5/16"KEY
SPRCKT,CAST,8T 50MM 1-3/8"BORE 5/16" KEY
SPRCKT,CAST,10T 42MM 1-3/8"BORE
BUSHING,BOOM INNER HARV-2004
RLR,BC,PU,5/8X3.5X2.375,PC
RLR,BC,PU,5/8X3.5X2.375X5FL,PC
RLR,BC,PU,5/8X4X1,PC
RLR,BC,PU,5/8X8X1.125,SC
RLR,BC,PU,5/8X4X1,SC
RLR,BC,PU,5/8X3.5X1X5FL,SC
STANDOFF,RLR,BC,5/8"x1-1/4"
COLLAR,SHAFT,SET,SCREW,5/8"
187
Operator's Manual MODEL 5640
188
Operator's Manual MODEL 5640
36" boom
Item #
1
2
3
4
5
6
7
8
9
10
11
12
Quantity
1
1
1
2
2
2
2
14
14
2
2
2
Part #
602613
192146
192145
173124
173101
050038
351316
351314
351309
351311
352252
351306
Description
CYL,2.00"x10",TIE ROD,20.25",1.125",3/4
BOOM,INNER,36" 6400-2004
BOOM,OUTER,36" 6400-2004
BAR,OUTER BOOM 6400-2004
BRAKT,VIDEO,LIGHT 6400-2004
BUSHING,BOOM INNER HARV-2004
RLR,BC,PU,5/8X3.5X2.375,PC
RLR,BC,PU,5/8X4X1,PC
STANDOFF,RLR,BC,5/8"x1-1/4"
RLR,BC,PU,5/8X3.5X2.375X5FL,PC
RLR,BC,PU,5/8X3.5X1X5FL,SC
RLR,BC,PU,5/8X3.5X2.375X5FL,SC
189
Operator's Manual MODEL 5640
190
Operator's Manual MODEL 5640
36" hopper options
Item #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
Quantity
1
1
1
1
1
1
1
1
1
2
2
2
1
1
1
1
6
4
12
12
Part #
192142
196417
195590
262029
196580
175071
262031
196553
175074
175061
174617
097.00105
352253
502410
173980
174618
351311
351316
351314
351309
Description
HOPPER,BOOM,36" 6400-2005
HOPPER,36" 20FT MAINFRAME,5640-11
TENSIONER WELDMENT
RUBBER,SIDE PANEL,36"
FRONT PANEL,36"BOOM,STD FRAME,5640-2011
SIDE,PANEL,HOPPER,20FT MAINFRAME,5640-11
RUBBER,36" BOOM 20FT MAINFRAME-5640-2011
FRONT PANEL,36 20FT MAINFRAME,5640-11
EXT,SIDE PANEL,36,20FT MAINFRAME,5640-11
FINGER TABLE MOUNT,5640
PLATE
TENSION SPRING [8-58-250]
CHN,LINK,3/16" x 16 LINKS
BOLT,EYE,1/2" x 8" W/NUT *PLATED*
ANGLE,TENTION,M-SEP,6440-2007
BAR
RLR,BC,PU,5/8X3.5X2.375X5FL,PC
RLR,BC,PU,5/8X3.5X2.375,PC
RLR,BC,PU,5/8X4X1,PC
STANDOFF,RLR,BC,5/8"x1-1/4"
191
Operator's Manual MODEL 5640
192
Operator's Manual MODEL 5640
36" boom mounting parts
Item #
Quantity
1
Part #
1 196414
Description
BOOM MOUNT 5640-2011
193
Operator's Manual MODEL 5640
194
Operator's Manual MODEL 5640
42"picking table
Item #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Quantity
1
2
1
2
2
4
2
22
6
4
2
1
1
2
26
Part #
196675
192768
352341
191879
192099
501220
353041
351314
351311
352252
352245
981155
982257
172896
351309
Description
FRAME,PICKING TABLE,42",6640-2011
WELD,PIVOT PLT FOBOOM 6400-2005
CHN,LINK,3/16" x 14"
PIN,PIVOT P.T. EXT
PIN,PIVOT,1"ODx3"L HARV BOOM
HAIRPIN,COTTER,3/16"x3-3/4" #21-08
RLR,BC,PU,5/8X5X1,SC
RLR,BC,PU,5/8X4X1,PC
RLR,BC,PU,5/8X3.5X2.375X5FL,PC
RLR,BC,PU,5/8X3.5X1X5FL,SC
RLR,BC,PU,5/8X4X1,SC
SPRING,7.27"L x 1"OD
CARIBIENER,SCREW LOCK,1/4" DIAMETER
WASHER,4-21/64" DIA 3/16
STANDOFF,RLR,BC,5/8"x1-1/4"
195
Operator's Manual MODEL 5640
196
Operator's Manual MODEL 5640
42" boom
Item #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
Quantity
2
1
1
2
2
1
2
2
4
18
4
18
2
1
2
1
2
Part #
602624
197046
197044
191999
602613
197045
351316
501900
352252
351314
111012
351309
351311
197094
982321
197093
351306
Description
CYL,3.00"x36",TIE ROD,46.25",1.375",3/4
PIVOT LINK,FOLD OVER BOOM,42IN,66X0-2012
BOOM,INNER,42IN FOLD OVER,66X0-2012
LEVER,BOOM FOLD OVER 6400-2004
CYL,2.00"x10",TIE ROD,20.25",1.125",3/4
BOOM,OUTER,42IN FOLD OVER,66X0-2012
RLR,BC,PU,5/8X3.5X2.375,PC
COLLAR,SHAFT,SET,SCREW,5/8"
RLR,BC,PU,5/8X3.5X1X5FL,SC
RLR,BC,PU,5/8X4X1,PC
BUSHING,.66"ID BORE x 3.25"LG x 1.24"OD
STANDOFF,RLR,BC,5/8"x1-1/4"
RLR,BC,PU,5/8X3.5X2.375X5FL,PC
BUMPER,OUTER,BOOM FRONT,66X0-2012
PLASTIC BUMPER
BUMPER,OUTER,BOOM REAR,66X0-2012
RLR,BC,PU,5/8X3.5X2.375X5FL,SC
197
Operator's Manual MODEL 5640
198
Operator's Manual MODEL 5640
42" hopper options
Item #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
Quantity
1
2
1
2
1
1
1
1
2
2
4
22
18
2
4
2
6
2
2
4
1
1
1
4
4
4
2
Part #
197219
197212
197210
181643
196552
262030
175561
175560
982340
175279
351311
351314
351309
602438
231119
175187
501900
050263
197214
352221
197211
175557
262015
321567
321569
321575
197213
Description
HOPPER, 42IN BOOM 20FT MAINFRAME,5640-11
POTATO DEFLECTOR 42" BOOM 5640-12
HOPPER, 42IN BOOM STD MAINFRAME,5640-11
COUPLING,1-3/8"x1"x3-3/4" 1/4"&5/16 KEY
FRONT PANEL,42 20FT MAINFRAME,5640-11
RUBBER,42" MAINFRAME-5640-2011
SIDE PANEL,42IN BOOM 20' M-FRAME,5640-12
COVER,EARS,BOOM HOPPER,66X0-2012
STOP POTATOES,BOOM HOPPER,5640-2012
TUBE,OUTER MOUNT,STOP POTATO,66X0-2011
RLR,BC,PU,5/8X3.5X2.375X5FL,PC
RLR,BC,PU,5/8X4X1,PC
STANDOFF,RLR,BC,5/8"x1-1/4"
MTR,HY,15.9CUIN,1"KEY,SAE-A,RE-SERIES,
BRNG,4BOLT,FLNG,1-3/8" ECC LOCK "R"
TORQUE ARE,BOOM,66X0-2011
COLLAR,SHAFT,SET,SCREW,5/8"
SHAFT,BUFFERBUNKER 6400-2005
BEARING MOUNT,FRONT,BOOM DRIVE,5640-2012
RLR,BC,PU,5/8X8X1.125,SC
FRONT PANEL 42" BOOM,STD M-FRAME,5640-12
COVER,EARS,BOOM HOPPER20"FRAME,5640-2012
RUBBER SHEET, HOLDING TANK HARV-2010
SPRCKT,CAST,10T 45MM 1-3/8"BORE 5/16"KEY
SPRCKT,CAST,8T 50MM 1-3/8"BORE 5/16" KEY
SPRCKT,CAST,10T 42MM 1-3/8"BORE
BEARING MOUNT,REAR,BOOM DRIVE,5640-2012
199
Operator's Manual MODEL 5640
200
Operator's Manual MODEL 5640
42" boom mounting options
Item #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
Quantity
1
1
1
1
1
1
1
2
2
2
2
6
1
1
2
2
2
2
2
2
4
4
2
Part #
196414
196079
196081
603018
196108
196409
196410
174827
353098
352153
352245
501900
175064
174828
231155
501901
231028
502799
050685
080248
231088
175567
603114
Description
BOOM MOUNT 5640-2011
PIVOT POINT.LH,SWINGING BOOM 5640-2010
BRACKET,SWINGING-BOOM,LH,5640-2010
CLY,3.00"x48",TIE ROD,58.25",1.50",3/4
PIVOT POINT SWINGING BOOM,RH 5640-2010
ROLLER MOUNT,FRONTSWINGINGBOOM,5640-2011
ROLLER MOUNT,REAR SWINGINGBOOM,5640-2011
COVER,FLANGE ROLLER SWINGING BOOM LH
ROLLER,3.5" WITH FLANGE,SWING BOOM,2012
RLR,BC,ST,5/8X3.5X2.375,SC
RLR,BC,PU,5/8X4X1,SC
COLLAR,SHAFT,SET,SCREW,5/8"
MOUNT,42IN BOOM,5640-2011
BRACKET,PIVOT PNT RH 5640-2010
BUSHING,TENSION 1"ID x 1/8"WALL x 1"L
COLLAR,SHAFT,SET,SCREW,3/4"
BRNG,INSERT,3/4" BORE SPHR OD VAN UNLDR
BOLT,HEX,HD,1"-8UNC x 3",SHRT HD GR5
ROLLER,SWINGING,BOOM,PIVOT POINT,RH 5640
PIPE
BRNG,INSERT,1" BORE FLAT OD KSK
WASHER,1" ID,1-1/2" OD,1/4" THICK
VALVE,ASSY,SWNG BOOM BRKAWAY,6640-2011
201
Operator's Manual MODEL 5640
202
Operator's Manual MODEL 5640
Bolt on frame catwalk
Item #
Quantity
Part #
Description
1
1
196458
TRASH CHUTE,PICKING TABLE,5640-11
2
1
196457
PLATFORM,CATWALK BOLT ON,5640-2011
3
1
196456
HANDRAIL,CATWALK BOLT ON M-FRAME,5640-11
4
1
196114
LADDER,REAR SWIVEL BOOM,5640-2011
5
2
175172
RAIL,CATWALK 5640-2011
6
2
175173
TUBE,RAIL CATWALK 5640-2011
7
1
175171
SHIELD,STAR TABLE 5640-2011
8
9
1
1
17.89.0061
175575
HOLDING BRACKET
GATE,CATWALK,BOLT ON MAINFRAME,5640-2012
203
Operator's Manual MODEL 5640
204
Operator's Manual MODEL 5640
Bolt on boom catwalk
Item #
1
Quantity
1
Part #
196458
Description
TRASH CHUTE,PICKING TABLE,5640-11
2
3
1
2
196415
196115
CATWALK,BOLT ON BOOM,5640-2011
RAIL,REAR,SWIVEL BOOM,5640-2010
4
5
2
1
174835
175097
RAIL,INNER,SWIVEL BOOM 5640-2010
MOUNT,BOLT ON BOOM CATWALK,5640-2011
6
7
1
1
175573
175574
GATE,REST,CATWALK,5640-2012
GATE,REST,CATWALK,HARV-2012
8
9
1
1
175070
196114
MOUNT,CATWALK,BOLT ON BOOM.5640-2011
LADDER,REAR SWIVEL BOOM,5640-2011
10
11
2
1
262068
175388
UHMW ADD ON STEP LADDER,66X0-2012
STEP,LADDER,ADD ON 66X0-2012
205
Operator's Manual MODEL 5640
206
Operator's Manual MODEL 5640
Catwalk with canopy
Item #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
Quantity
1
1
1
1
1
1
2
2
4
1
4
2
8
2
1
2
3
2
1
2
2
6
4
2
1
Part #
131431
192946
192329
192945
196895
196456
981495
352415
196896
197227
173091
173088
173086
175322
173090
173085
173203
502452
173089
173202
175326
981646
981647
173087
175173
Description
CANOPY FRAME HARV-2008
CANOPY CHANNEL 101" LONG 6400-2005
CANOPY CHANNEL 128" LONG 6400-2004
CANOPY CHANNEL 76" LONG 6400-2005
PLATEFORM,ADD ON,CANOPY,5640-2012
HANDRAIL,CATWALK BOLT ON M-FRAME,5640-11
CLAMP,TOGGLE,PULL-ACTION,DESTACO-371
CHAIN,LINK 3/16"x48"
RAIL,ADD ON CATWALK,5640-2011
SHIELD,ADD ON PLATFORM,5640-2011
TUBE
SHEET
SHEET,BOLT MNT F/O CANOPY HARV-2004
SUPPORT HNDRL,FOLT AWAY CANOPY,5640-2011
CANOPY BRACKET FOB HARV-2004
PLATE
PLATE,CLAMP,CANOPY 6400-2004
BOLT,EYE,SHLDR 3/8"-16 x 2-1/2" *PLATED*
PLATE,FOBOOM BRACE HARV-2004
SUPT,SPRING,CANOPY 6400-2004
ADAPTER,GAS SHOCK,CANOPY,5740-2011
CLEVIS,FORK,THREADED ENDS,M8
SPRING,GAS,12.8STROKE,200# FORCE,M8THRED
SHEET
TUBE,RAIL CATWALK 5640-2011
207
Operator's Manual MODEL 5640
208
Operator's Manual MODEL 5640
Lights
Item #
Quantity
Part #
Description
1
1
402994
LGHT,STROBE,AMBER LED
2
1
402991
LGHT,SIGNAL,STOP,AG-LED-R4
3
7
402353
LGHT,UTILITY,TRACTOR,12V,SEAL BEAM649312
4
7
402998
LGHT,LED,WORKLIGHT 20W 90DEG 12VCD
5
2
402993
LGHT,SIGNAL,STOP,AG-LED-AA
6
2
173101
BRAKT,VIDEO,LIGHT 6400-2004
7
1
402992
LGHT,SIGNAL,STOP,AG-LED-L4
209
Operator's Manual MODEL 5640
210
Operator's Manual MODEL 5640
Blower
Item #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
Quantity
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
2
1
1
Part #
196500
192240
192244
192658
192241
192235
261565
175133
196499
173680
171416
981269
601716
781285
571163
173701
981242
501371
501812
171453
781283
175132
781289
231126
181540
231245
602994
821399
231246
Description
TIGHTENER,BLOWER DRIVE,5640-2011
SHLD,BLOWER OPEN CNTR,6400-2004
BLOWER BEARING MNT 6400-2004
BLOWER,IMPELLER,WELD 6300/6400-2004
SHLD,BLOWER CLOSED CTR 6400-2004
BLOWER HOUSING
BELT,POWER,BAND,4/B240 HI-POWER
MOUNT,RH,SHIELD,BLOWER DRIVE,5640-2011
SHIELD BLOWER DRIVE
SUPPORT,BLOWER,6400-2006
PIN,TIGHTENER,BLOWER BELT
CLAMP,HOSE,SS,3-1/16" TO 4" DIA. #56
CAP,PLUG,3-1/2"DIA. #SC3-1/2
CLUTCH,OVERRUNNING,LH,D&T
YOKE,END,ADJUSTABLE,1/2"-13UNCx1/2"PIN
ROD,SPRING,TENSION BLWR BELT .5x16L
SPRING,ELIM,2-3/4"L x 1.250"OD .175 8COI
WASHER,FLAT,5/8" (SAE)
NUT,HEX,1/2"-13UNC
SPACER,BLOWER,TIGHTNER 1-1/4ODx2"L 5600
IDLER,PULLEY,FLAT,FACE,6.5"ODx3.5"Wx5/8"
MOUNT,SHIELD,BLOWER DRIVE,5640-2011
SHEAVE,4GROOVE,B,8.6"ODx4"BORE (CLUTCH)
BRNG,INSERT,1-3/4",ECC,LOCK/FLAT OD AG
ADAPTER,CLUTCH/SHEAVE 5.5"ODx3.31"LONG
BRNG,4BOLT,2"SM,FIXED DODGE 069704
HOSE,EXT,GREASE ZERK,BLOWER,HARV-2010
SHAFT,HARV FAN 6300/6400-2004
BRNG,4BOLT,2"SM,FLOATING DODGE 069732
211
Operator's Manual MODEL 5640
212
Operator's Manual MODEL 5640
Blower plenum
Item #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Quantity
1
1
1
1
1
1
2
1
4
4
7
7
1
1
Part #
194492
195081
194491
195047
196038
192660
981859
171413
174057
174058
171649
171911
262036
262036
Description
BLOWER DUCT UPPER ELBOW 5640-2007
BLOWER DUCT,STEEP PLENUM,5640-2008
BLOWER DUCT LOWER ELBOW 5640-2007
PLENUM,STEEP 5640-2008
AIRHOOD,CURVED 5640-2010
AIR HOOD EXTENSION 6400-2005
UHMW,PLENUM COVER 6400-2007
PLENUM,END,3/16"x18-3/4"x27" 5600
PLENUM SPLICE BAR 23.19 LONG 5640-2007
PLENUM SPLICE BAR 14.938 LONG 5640-2007
SPACER,PLENUM 1/4" x 1-5/8" LN 5600/6400
SPACER,PLENUM 1/4" x 1-1/4" LONG 6400
RUBBER,SIDE PANEL AIRHOOD,5640-2011
RUBBER,SIDE PANEL AIRHOOD,5640-2011
213
Operator's Manual MODEL 5640
214
Operator's Manual MODEL 5640
Toolkit
Item #
Quantity
Part #
Description
1
1
981945
BELTED CHAIN ROD STRAIGHTENER
2
1
982145
CROWBAR,36"
3
1
982144
SCRAPER,WOOD HANDLE
4
1
982143
SHOVEL,WOOD HANDLE
5
1
175566
MOUNT,TOOLBOX,6621-2012
6
1
197020
HOLDER,TOOLS,BOOM HOPPER,66X0-2012
7
1
197307
MOUNT,TOOLBOX HARV-12
8
1
981701
TOOLBOX,CRAFTSMAN,23 LH LONG #965433
215
Operator's Manual MODEL 5640
216
Operator's Manual MODEL 5640
Standard Shields
Item #
Quantity
Part #
Description
1
6
300402
TAPE,ORANGE,REFLECTIVE x 9"
2
6
300400
TAPE,RED,REFLECTIVE x 9"
3
14
300401
TAPE,YELLOW,REFLECTIVE x 9"
4
1
174843
SHIELD,TABLE DRIVE 5640-2011
5
1
197196
SHIELD,PRIMARY DRIVE LH,5640-2012
6
2
982253
LEVER LATCH,SOUTHCO
7
4
982254
BUMPER,RUBBER,3/4"DIAx1/2" HIGH 10-24
8
3
196551
BRACKET,LATCH,REAR SHIELD,5640-2011
9
1
192515
SHIELD,FRNT PTO EXTND HARV-2004
10
1
019.00487
HINGE,1-15/16"
11
1
174814
SHIELD,FRONT TORQUE TUBE 5640-2010
12
2
175549
SHIELD,VALVE BANK,5640-2012
13
1
197195
SHIELD,RH PRIMARY DRIVE,5640-2012
14
1
300211
STICKER,MDL 5640 GRAY 3.3"
15
2
300420
STICKER,STRIPE RH,PRIM DRIVE,5640-2012
16
3
981664
HANDLE,SHIELD,6140 NA4ZN
17
1
175548
MOUNT,TOOLBOX,6621-2012
18
1
982295
UHMW,SUPPORT,PRIMARY,SHIELD,REAR,66X0-11
19
2
981950
SPRING,GAS,7.87STROKE,200# FORCE,M8THRED
20
6
981646
CLEVIS,FORK,THREADED ENDS,M8
21
1
197194
SHIELD MOUNT,VINE CHAIN DRIVE,66X0-2011
22
1
175449
STOP,SHIELD,VINE CHAIN,66X0-2012
23
2
300419
STICKER,STRIPE RH FRNT,VINECHN,5640-2012
24
1
197193
SHIELD,VINE CHAIN DRIVE,FRONT,5640-2012
25
26
1
1
197192
300166
SHIELD,VINE CHAIN DRIVE,5640-2012
STICKER,SPUDNIK,6" X 30.5" LG GREY
217
Operator's Manual MODEL 5640
218
Operator's Manual MODEL 5640
Shields with brushroller
Item #
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Quantity
1
3
1
1
1
1
3
2
1
1
1
1
1
1
1
Part #
196514
982253
194965
196513
194966
174843
982254
196551
192515
174814
175116
194964
171651
174076
196550
Description
SHIELD,PRIMARY,LH 5640-2011
LEVER LATCH,SOUTHCO
SHIELD,SEC DRIVE,RH,5640-2008
SHIELD,PRIMARY,RH 5640-2011
SHIELD,DEVINER DRIVE,RH,5640-2008
SHIELD,TABLE DRIVE 5640-2011
BUMPER,RUBBER,3/4"DIAx1/2" HIGH 10-24
BRACKET,LATCH,REAR SHIELD,5640-2011
SHIELD,FRNT PTO EXTND HARV-2004
SHIELD,FRONT TORQUE TUBE 5640-2010
SHIELD,HYDRAULIC VALVE BLOCK,5640-2011
PIVOT,SHIELDS,RH,5640-2008
SHLD,SLIDE,VINE,CHN,DRIVE 5600
SHLD VINE CHAIN INNER 5640-2007
BRACKET,LATCH,REAR SHIELD,5640-2011
219
F
E
D
C
B
A
Status
03­A
We reserve all rights in this document and in the informa­
tion contained therein. Reproduction, use or disclosure
to third parties without express authority is strictly
forbidden.
© SPUDNIK EQUIPMENT
1
2
3
4
5
6
Change
2
Date
10/20/11
Name
EBH
3
Date
User
Proofed RJB
Standard
Origin
Repl. f.
ALL
4
Repl. by
5
6
SPUDNIK EQUIPMENT COMPANY LLC
584 W. 100 N. BLACKFOOT,ID,83221
www.spudnik.com
SWING BOOM/MULTISEP CONFIG.
MULTISEP/ROLLERSTAR CONFIG
DRIVE OPTIONS
PWM ROCKER SHAKER CONFIGURATION
DRIVE OPTIONS
HOLDING TANK SELF HYDRAULIC MULTISEP
8
9
10
11
12
13
14
7
6XXX­HARVESTERS­03­F
Sheet 1
of
16
8
Print Date: 5/23/2012
LOW COST CONTROL PLATFORM­ELEC.
BOOM/HOLDING TANK DRIVE
7
17
STEERING & LEVELING OPTIONS
6
TRACTOR DRIVEN WHEEL ASSIST
PWR DN DIGGER NOSE/COULTERS
5
16
DIGGER NOSE OPTIONS
4
HYDRAULIC BLOWER
OVERVIEW ­ WITH HOLDING TANK
3
15
OVERVIEW ­ NO HOLDING TANK
2
8
COVERSHEET
7
1
Contents:
Order:
MACHINE: 6XXX­HARVESTERS­03­F
COMPLETE HYDRAULIC UPDATE
1
F
E
D
C
B
A
B
A
A
B
B
A
A
2
03­A
DESCRIPTION OF REVISION
COMPLETE HYDRAULIC UPDATE
SINGLE BAND = PRESSURE
DOUBLE BAND = RETURN
RED = FUNCTIONS
BLUE = BOOM DRIVE / HOLDING TANK
YELLOW = BRUSH DRIVE / TRASH CONV.
GREEN = HYD. SHAKER
BLACK = HYD. JACK
B
ECN#
QUICK COUPLER CAP COLOR CODE
REVISION
D
C
B
B
OPTION Y9
OPTION Y11
A
1
OPTION Y8
OPTION Y10
B
A
B
A
B
RH & LH COULTERS
STEERING
OPTION Y6
A
4
B
OPTION Y7
DATE
10/20/11
NAME
EBH
ORDR
CUST
APPR RJB
DATE
ORIG
2nd Table Space
2nd Table Angle
Shaker Ram
or Full Width RS
Supp. Wheel Full Width MS
Clod Roller Height Full Width MS Spacing
LH & RH Leveling Left Level X X
X X
Y0.0
A
B
EXT.VALVE
OPEN CENTER
OPT. LOCATION
A
PRESSURE
TANK
INSTALL EXT. VALVES ON FRONT & BACK OF MANIFOLD SLAVE VALVE Y0.0,Y0.1,Y1.1,Y1
#602383­COIL
#602382­CARTRIDGE
6
Rock Box Open
Rock Box Close
Discharge
Charge
Ridge Relief On
X
X
X
Digger Up
Digger Down
Y1B
Plug #
X
SHEET
OF 16
X
X
Y1.3
X
X
X
X
Y1.2
2
D
C
B
A
SPUDNIK EQUIPMENT COMPANY LLC
584W 100N
BLACKFOOT,ID,83221
www.spudnik.com
X
X
Y1.1
LOGIC SETUP FOR
MACHINES WITHOUT HOLDING TANK
602061 VALVE,SOLENOID,12VDC 4WAY (CONN PLUGS)
601647 CARTRIDGE,P.O.,CHECK,VALVE CP450­1
602382 VALVE 2/2 NC CARTRIGE W/O COIL D. BLOCKING
602383 COIL 12VDC DIN FOR 602382 602159
601646 PLUG,SOLENOID,UNLOAD,VALVE CP­B­2­B
PH0174 ­ STD 7 STATION VALVE BANK PARTS
­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­­
B
INNER BOOM
OUTER BOOM
ALL­HARVESTERS­03­A
A
Y1.2
CLOSED CENTER
STD LOCATION
5
Y1.1 MASTER
This drawing is the sole property of the above named. All rights of
the design and/or invention are reserved. No part of this document may be reproduced without prior written permission prior written permission
X X X X
X X X X X
X X X X X X
X
X X
X X X
X X
X
Valve # Priority 6 7 8 9 10 11 PRIORITY LIST FOR INSTALLED OPTIONS
A
3
Y0.1
Y0.0
03­A
REVISION
D
C
B
A
DESCRIPTION OF REVISION
COMPLETE HYDRAULIC UPDATE
ECN#
DATE
10/20/11
X
DISCHARGE
X
X
NAME
EBH
X
X
Y1.3 Y0.1
CHARGE
X
X
X
Y1.2
X
X
Y1.1
RIDGE RELIEF ON
ELEVATOR DN
ELEVATOR UP
DIGGER DOWN
DIGGER UP
Y1B
ORDR
CUST
APPR RJB
DATE
ORIG
MAIN VALVE BANK
LOGIC SETUP FOR MACHINES WITH HOLDING TANK
2
3
Y21
Y23
X
X
Y22
X
Y23
X
X
Y24
ALL­HARVESTERS­03­A
X
Y21
This drawing is the sole property of the above named. All rights of
the design and/or invention are reserved. No part of this document may be reproduced without prior written permission prior written permission
LESS STEEP DOWN
LESS STEEP UP
FAST FWD
SLOW FORWARD
SLOW BACKWARD
FOLD OVER DN
FOLD OVER UP
Y20
4 STATION VALVE BANK
LOGIC SETUP FOR MACHINES WITH HOLDING TANK
Y27
DOWN
REVERSE
X
Y26
3
TANK
PRESSURE
SHEET
OF 16
6
D
C
B
A
SPUDNIK EQUIPMENT COMPANY LLC
584W 100N
BLACKFOOT,ID,83221
www.spudnik.com
X
Y27
Y23
REVERSE
FWD
FWD
UP
UP
DOWN
Y24
Y22
Y20
Y26
5
FOLD OVER BOOM
4
BOOM SLOW
HOLDING TANK LESS STEEP
1
BOOM FAST
601338
601338
REVISION
D
C
B
601443
601370
602203
A
B
DESCRIPTION OF REVISION
B
A
A
602944
N/A
B
KIT #602434
602944
KIT #602708
OPTION RIDGE RELIEF
602321
602159
1
601323
602230
KIT #602267
602229
KIT #602435
KIT #602435
KIT #602267
602230
602229
601993
602755
2
KIT #602267
602228
KIT #602435
601338
4 ROW
601768
602228
602323
3 ROW
601338
602240
602232
B
601849
A
KIT #602335
A
601338
A
601817
RH COULTER
602229
KIT #602434
602241
KIT #602708
602231
N/A
ECN#
601338
KIT #602335
B
B
B
602228
LH COULTER
DATE
A
NAME
601338
ORDR
CUST
APPR
DATE
ORIG
4
B
B
BACK
BACK
601956
B
602617
2.5" X 14"
601956
2
601378
­Y0.9
601643
ALL­HARVESTERS­03­A
1
TOP
SIDE
SLAVE Y0.1
#602382 & #602383
HOLDING TANK ELEVATOR OPTION
LH
A
HOSE A
5
MAIN VALVE BANK
This drawing is the sole property of the above named. All rights of
the design and/or invention are reserved. No part of this document may be reproduced without prior written permission prior written permission
A
602617
2.5" X 14"
RH
A
601322
HOLDING TANK/DIGGER NOSE OPTION (6340)
601338
KIT #602335
602181
2 ROW
A
A
A
OUTER
BOOM
3
602181
B
HOSE A HOSE B HOSE C HOSE D HOSE E
B
B
601338
INNER BOOM
601323
A
6
3.00"x6"
601637
A
B
B
A
SHEET
OF 16
601390
601390
601389
601389
601389
601389
602133
4
601048
601048
D
C
B
A
SPUDNIK EQUIPMENT COMPANY LLC
584W 100N
BLACKFOOT,ID,83221
www.spudnik.com
601637
602181
HOSE E
601713
OPTION HOLDING TANK
B
A
2
HOSE C
601338
SLAVE Y1.2
SLAVE
Y1.1
HOSE B
MASTER Y1
601713
601957
601713
HOLDING TANK ELEVATOR OPTION
1
P
T
602618
601713
601338
602122
602122
ELEVATOR LIFT
REVISION
D
C
B
601323
601323
601322
601323
601323
HOSE C
HOSE B
A
LH
602617
2.5" X 14"
HOSE E
HOSE E
DESCRIPTION OF REVISION
­Y0.7
TOP
601643
SIDE
2
SLAVE Y0.1
1
ECN#
Note: Install #602519 to back of manifold
MAIN VALVE BANK
DATE
NAME
ORDR
CUST
APPR
DATE
ORIG
BACK
HOSE A
B
BACK
REAR BOTTOM 602519
601892
A
601332
1
B
B
602210
KIT #602436
602234
KIT #602269
603103
KIT #603145
603103
KIT #603111
602230
KIT #602337
603103
KIT #603144
602206
A
601323
A
B
B
2.00"x8"
602612
602232
KIT #602268
602232
KIT #602268
602232
KIT #602268
B
B
601323
602133
KIT #602269
602233
KIT #602436
602244
KIT #602337
LH/RH COULTER
ALL­HARVESTERS­03­A
A
602133
KIT #603111
601497
KIT #603145
This drawing is the sole property of the above named. All rights of
the design and/or invention are reserved. No part of this document may be reproduced without prior written permission prior written permission
A
2.00"x8"
602612
KIT #603111
KIT #602267
KIT #602267
KIT #602267
2
601774
601497
601497
601774
603142
4 ROW
KIT #603145
601034
601036
601034
KIT #602435
601034
KIT #602435
KIT #602435
HOSE F
601704
601338
3 ROW
603100
KIT #603144
603100
KIT #603144
601032
KIT #602335
601032
KIT #602335
601662
KIT #602335
A
2 ROW
HOSE H
OPTION
POWER DOWN DIGGER NOSE
A
A
B
A
6
HOSE F HOSE G HOSE H HOSE I
601338
RH
601322
MASTER Y1
601048
601390
A
B
B
601659
602378
602426
601748
601750
601048
601659
602378
601637
602426
601748
601338
SLAVE Y1.2
HOSE D
A
INNER BOOM
601477
B
B
601338
B
601713
601713
OUTER
BOOM
HOSE A HOSE B HOSE C HOSE D HOSE E
LH COULTER
602617
2.5" X 14"
601338
B
5
601338
A
B
4
SHEET
OF 16
A
A
5
KIT #602268
602231
KIT #602268
602231
KIT #602268
602231
HOSE J
D
C
B
A
SPUDNIK EQUIPMENT COMPANY LLC
584W 100N
BLACKFOOT,ID,83221
www.spudnik.com
A
3
HOSE I
2
A
601338
RH COULTER
HOSE G
B
HOSE J
A
P
T
601338
B
1
601338
601390
03­A
REVISION
D
C
B
A
602414
602414
LH STEER
RH STEER
HOSE C
HOSE D
601325
B
A
3"x8" REPHASING
602628
601322
602266
KIT #602277
602203
KIT #602277
602266
KIT #602437
602203
602265
KIT #602437
602203
KIT #602277
602250
KIT #602437
602234
602210
KIT #602277
602203
KIT #602437
602203
602203
KIT #602277
602263
KIT #602437
602233
602244
KIT #602278
602231
KIT #602440
KIT #602278
602245
KIT #602440
602245
KIT #602346
602231
602231
602245
KIT #602346
A
B
KIT #602278
602251
KIT #602440
602234
KIT #602346
602207
HOSE I
602251
KIT #602278
602250
KIT #602440
602285
KIT #602346
602210
HOSE J
601323
601323
B
DESCRIPTION OF REVISION
ECN#
DATE
10/20/11
NAME
EBH
ORDR
CUST
APPR
DATE
ORIG
A
LH
602632
4.00"x8"
A
RH
602632
4.00"x8"
5
601713
A
601577
601577
LH LEVELING ONLY
ALL­HARVESTERS­03­A
B
601477
602133
602133
HOSE J
This drawing is the sole property of the above named. All rights of
the design and/or invention are reserved. No part of this document may be reproduced without prior written permission prior written permission
B
601477
B
602135
602800
*NO HOSE KIT HAS BEEN CREATED FOR 2 ROW MASTER SLAVE STEERING
KIT #602277
602265
KIT #602437
602265
602266
A
601323
602628
HOSE H
602135
HOSE A HOSE B HOSE C HOSE D HOSE E HOSE F HOSE G
COMPLETE HYDRAULIC UPDATE
4 ROW
3 ROW
2 ROW*
4"x6"
4"x6"
A
RH & LH LEVELING
HOSE H
5640 MASTER/SLAVE STEERING
HOSE I
4
HOSE G
OPTION MASTER SLAVE STEERING
601713
601713
A
B
3
602234
2
HOSE F
HOSE E
3"x8" REPHASING
602240
A
B
B
A
602135
602135
A
B
602146
601322
602146
HOSE B
HOSE A
B
602285
A
SHEET
OF 16
6
6
D
C
B
A
SPUDNIK EQUIPMENT COMPANY LLC
584W 100N
BLACKFOOT,ID,83221
www.spudnik.com
FA 4049
B
1
602632
601504
601338
B
HOSE B
602247
KIT #602272
602241
KIT #602272
602247
KIT #602272
602241
KIT #602434
602944
KIT #602708
602944
N/A
KIT #602434
602241
KIT #602708
602231
N/A
KIT #603184
602203
KIT #602271
602230
KIT #602271
602230
602230
KIT #603184
603067
KIT #602271
602240
KIT #602271
602240
602240
KIT #603184
602745
KIT #602271
602745
KIT #602271
602745
602745
KIT #603184
602255
KIT #602271
602239
KIT #602271
602239
602239
KIT #603184
602245
KIT #602271
602284
KIT #602271
602284
602284
KIT #603184
602255
KIT #602271
602239
KIT #602271
602239
602230
KIT #603184
602217
KIT #602271
602241
KIT #602271
602241
602241
HOSE P
ECN#
DATE
10/20/11
NAME
EBH
ORDR
CUST
APPR RJB
DATE
ORIG
*NO HOSE KIT HAS BEEN CREATED FOR 2 ROW, 42" FOLD OVER BOOM
KIT #603184
603183
KIT #602271
602211
KIT #602271
602211
602211
KIT #602272
602245
KIT #602272
602245
N/A
HOSE J HOSE K HOSE L HOSE M HOSE N HOSE O
KIT #602272
602240
KIT #602272
602240
N/A
DESCRIPTION OF REVISION
COMPLETE HYDRAULIC UPDATE
602266
KIT #603184
603182
KIT #603184
602211
KIT #602271
602206
KIT #602271
602211
KIT #602271
602206
KIT #602271
3 ROW
602211
602206
03­A
N/A
KIT #602272
N/A
2 ROW*
5640
601338
601504
B
602623
3.00"x24"
INNER BOOM
HOSE A HOSE B HOSE C HOSE D HOSE E HOSE F
HOSE G HOSE H HOSE I
4 ROW
3 ROW
4 ROW
A
A
B
36" BOOM 6300/6400­2004
2 ROW
A
601338
REVISION
D
C
B
A
A
HOSE A
B
601347
B
HOSE C
A
B
601504
B
601323
A
B
601395
601477
602133
602133
B
2.00"x10"
601338
A
A
B
HOSE K
603023
This drawing is the sole property of the above named. All rights of
the design and/or invention are reserved. No part of this document may be reproduced without prior written permission prior written permission
ALL­HARVESTERS­03­A
601713
P
A
B
601323
6
SHEET
OF 16
601956
601323
7
D
C
B
A
SPUDNIK EQUIPMENT COMPANY LLC
584W 100N
BLACKFOOT,ID,83221
www.spudnik.com
B
601338
601477
B A
602133
601477
602133
FOLD OVER SPEED
#981155 SPRING
#982257 CARIBIENER
2.00"x10"
3.00"x36"
3.00"x36"
602133
OPTION 42" FOLD OVER BOOM
NOTE: USE 3/8" HOSES ON 6640 INNER BOM
A
601323
HOSE J
602613
C
2.00"x10"
601323
HOSE D
601323
HOSE H
HOSE G
A
OUTER BOOM
601957
601347
601957
601956
601713
A
601347
OUTER BOOM
OUTER BOOM
602624
602624
601713
601446
5
601956
4
601713
601323
3
HOSE I
C 602613
C 602613
A
B
A
B
602130
INNER BOOM
INNER BOOM
A
B
A
B
2
601504
HOSE N
HOSE M
1
601347
602066
HOSE L
601504
601956
601347
602066
HOSE O
HOSE P
03­A
REVISION
D
C
601770
603113
603114
1
2
5640­ KIT #133407
601030
603114
DESCRIPTION OF REVISION
COMPLETE HYDRAULIC UPDATE
ECN#
602134
DATE
10/20/11
601323
A
HOSE A
601323
601338
601323
601770
#603122­ CAVITY PLUG (QTY. REQ. 2)
#603114­ FACTORY PRE­SET AT 300 PSI
USE 3/8" HOSE FOR BREAKAWAY FUNCTION
1
2
601770
B
601323
601030
601030
A
NAME
EBH
601956
4 ROW
3 ROW
B
ORDR
CUST
602239
KIT #603110
602255
KIT # 602442
APPR RJB
DATE
ORIG
601323
A
602610
2.00"x4"
A
601713
HOSE C
601323
B
602612
2.00"x8"
602233
KIT # TBD
602256
KIT # TBD
KIT #603110
602229
602232
KIT # 602442
KIT # TBD
602233
KIT # TBD
602229
602252
KIT # TBD
602252
KIT # TBD
602253
KIT # TBD
602253
KIT # TBD
KIT # TBD
602231
KIT # TBD
602231
HOSE A HOSE B HOSE C HOSE D HOSE E HOSE F HOSE G
HOSE B
B
OPTION 11
B
A 601338
2.00"x8"
602612
601338
602255
602612
2.00"x8"
A
601713
601323
5
B
ALL­HARVESTERS­03­A
This drawing is the sole property of the above named. All rights of
the design and/or invention are reserved. No part of this document may be reproduced without prior written permission prior written permission
601338
HOSE B
A
B
OPTION 9
A
B
B
601770
TABLE SPACING
A
OPTION 10
601338
A
601338
A
HOSE D
LH SHAKER
601323
601338
A
B
B
TABLE ANGLE
A
RH SHAKER
601323
602912
FOR FULL WIDTH M/S TABLE USE #602230 (17' HOSE)
601338
602624
4.00" x 36"
A
602912
ROLLERSTAR / MULTISEP TABLE
OPTION 8
OPTION SHAKER RAM
B
B
HOSE E
A
HOSE F
601338
A
A
B
SHEET
OF 16
8
A
D
C
B
A
SPUDNIK EQUIPMENT COMPANY LLC
584W 100N
BLACKFOOT,ID,83221
www.spudnik.com
602619
3.00"x8"
601713
6
601323
SUPPORT WHEEL
A
B
A
4
B
B
602134
OPTION 7
3
601338
OPTION SWING BOOM
2
B
B
HOSE G
601338
A
HOSE G
B
B
1
STEERING
601338
03­A
REVISION
D
C
602133
601323
601713
601323
601713 602137
DESCRIPTION OF REVISION
COMPLETE HYDRAULIC UPDATE
L/H
601713
601322
A
B
2" X 8"
602281
602234
602137
602257
602211
602285
A
B
602221
TERRA FLOAT
601338
B
601338
601322
601338
602256
602240
602610
2" X 4"
LH
602612
601713
602610
2" X 4"
RH
R/H
2" X 8"
B
602211
602284
A
B
A
602133
601338
602612
ECN#
A
602610
DATE
10/20/11
NAME
ORDR
CUST
APPR
DATE
ORIG
601338
B
601338
EBH
6X40 ONLY
SPACING FULL WIDTH R/S
601347
602133
602244
A
A
A
601713
601338
OPTION 11
B
A
602244
A
B
601323
601713
601338
602230
601338
601338
FA 7930
602612
2" X 8"
601323
B
601338
601338
601713
601338
601338
FA7606
602619
3.00 x 8"
ALL­HARVESTERS­03­A
A
602133
ROCKBOX
This drawing is the sole property of the above named. All rights of
the design and/or invention are reserved. No part of this document may be reproduced without prior written permission prior written permission
A
602133
B
A
602230
B
B
A
STRIPPER LIFT
6
601338
A
601323
SIMPLE SEP TABLE ANGLE
601338
B
602133
SHEET
OF 16
9
601338
602612
2.00 x 8"
D
C
B
A
SPUDNIK EQUIPMENT COMPANY LLC
584W 100N
BLACKFOOT,ID,83221
www.spudnik.com
601713
FULL WIDTH ROLLERSTAR
OPTION 9
601323
B
B
602229
A
602596
A
601338
A
B
A
601323
OPTION 8
602217
MULTISEP SCRAPER
B
B
5
A
4
A
A
B
3
B
B
602217
OPTION 7
2
A
1
B
B
B
B
A
OPTION 10
A
OPTION 6
03­A
REVISION
D
C
B
A
601749
601749
602367
601659
601390
601048
1
601486
601711
601744
602096
DESCRIPTION OF REVISION
602734
601378
PINCH ROLLER DRIVE
601370
602323
602734
2
ECN#
DATE
10/20/11
601049 601048
601745
601849
FA7034 MULTI­SEP DRIVE
601048 601049
601849
COMPLETE HYDRAULIC UPDATE
601390
601425
SEGMENT ROLL DRIVE
603129
601370
601390
SPREADER ROLL UNIT
601749
601749
601659
601724
NAME
EBH
601390
602248
602367
601390
601048
601744
602367
601425
ORDR
CUST
APPR RJB
DATE
ORIG
601749
601749
601749
601749
601849
601390
1
2
3
601443
SHAKER MOTOR
602507
602552
601048
602525
3
601443
601659
601390
601048
PRESSURE
601749
2
601575
601659
601390
601048
RETURN
601749
601637
601378
601659
601048
602426
602547
601390
RETURN
HYDRAULIC ROLLERSTAR DRIVE
SHEET
OF 16
602426
601637
601390
PRESSURE
6
10
FA6260 ROLLERSTAR DRIVE
REPLACED FA6689 ­ ROLLERSTAR ONLY D
C
B
A
SPUDNIK EQUIPMENT COMPANY LLC
584W 100N
BLACKFOOT,ID,83221
www.spudnik.com
601711
5
ALL­HARVESTERS­03­A
601849
1
FA4072 6400­2004 (PWM)
602767
4
This drawing is the sole property of the above named. All rights of
the design and/or invention are reserved. No part of this document may be reproduced without prior written permission prior written permission
602551
602525
SHAKER MOTOR
601390
601048
FA5782 (SHAKER ON/OFF)
OPTION SHAKER SPEED CONTROL FA7239
ROCKER SHAKER
601657
601749
ROCKER SHAKER
601657
601749
601637
601720
601425
SPREADER ROLLER
601048
601659
602214
601637
601656
ROLLERSTAR
03­A
STANDARD 36" BOOM DRIVE
FA8699­ 6640 FOLD OVER, 42" SWING BOOM DRIVE
ECN#
DATE
10/20/11
602426
602433
602547 RETURN
601390
601659
DESCRIPTION OF REVISION
602426
602426
601993
NAME
EBH
ORDR
CUST
601048
FA3581
TRASH CONVEYOR
601048
601390
601754
601424
STANDARD TIMING
PARKER/ WHITE
REAR VIEW
FLOW A to B
This drawing is the sole property of the above named. All rights of
the design and/or invention are reserved. No part of this document may be reproduced without prior written permission prior written permission
ALL­HARVESTERS­03­A
IF ROCKER OR ROTARY SHAKER IS INSTALLED, THERE IS A 5th REMOTE VALVE ON THE TRACTOR REQUIRED FOR BRUSH OR TRASH CONVEYOR DRIVE
APPR RJB
DATE
ORIG
601048
601390
601390
602547
601390
601657
601048
602426
COMPLETE HYDRAULIC UPDATE
601719
602670
2
601390
601655
601048
601378
601749
601749
3
601390
ROTARY SHAKER
5
601048
FA4072 6400­2004
601048
601446
PRESSURE
601390
FA3675 36" 2004
REVISION
D
C
602767
601754
601700
601390
601659
601993
1
601378
BRUSH DRIVE
602547
601378
601390
601390
601390
601390
601048
601424
FA3582
B
4
6
601048
D
C
B
A
SPUDNIK EQUIPMENT COMPANY LLC
584W 100N
BLACKFOOT,ID,83221
www.spudnik.com
11
602264
SHEET
OF 16
602689
601577
601048
RETURN
601378
601749
601749
601577
601048
PRESSURE
602009
601390
601749
601238
601749
601048
601749
601749
601446
B
A
602553
A
3
3.00"x10"
602620
601749
601753
601749
2
602689
A
B
1
FA5787 HYD. JACK
602438
F
E
D
C
We reserve all rights in this document and in the informa­
tion contained therein. Reproduction, use or disclosure
to third parties without express authority is strictly
forbidden.
© SPUDNIK EQUIPMENT
Status
03­A
1
COMPLETE HYDRAULIC UPDATE
Change
602519
602519
602612
A
601323
602133
602381­
603007
B
602282
601477
B A
B2 B1 A2 A1
B
2
Date
10/20/11
Name
EBH
HOLDING TANK LESS STEEP
Date
User
602265
3
Proofed RJB
Standard
601713
T
601713
602133
602133
6300 MODEL (4 VALVE MANIFOLD #603007)
P
T
P
A
LESS STEEP
2" x 8"
602623
602282
A
B
603035
602239
601477
601956
602211
B2 B1 A2 A1
Origin
Repl. f
601713
601713
HLD TANK FOLD OVER BOOM
602381­
A
601956
601477
B
4 ROW
KIT #602434
4
602282
KIT #602434
KIT #602434
602223
KIT #602708
A
602061­
HOLD TANK SLOW FWD/REV
B2 B1 A2 A1
602381­
A
HOSE B
HOSE B
HOLDING TANK BOOM DRIVE
KIT #602434
602282
KIT #602708
602223
602367
602670
HOLD TANK
FAST FWD
B A
B2 B1 A2 A1
HOSE A
B
T
T
P
2.00"x10"
2.00"x10"
Repl. by
5
6
SPUDNIK EQUIPMENT COMPANY LLC
584 W. 100 N.
BLACKFOOT,ID,83221
www.spudnik.com
601323
601323
601323
A
B
7
602427
602427
6XXX­HARVESTERS­03­F
602797
602797
601659
602426
8
Sheet 12
of 16
8
602547
601390
602130
2.00"x10"
Print Date: 5/23/2012
602426
601390
B
STANDARD TIMING
PARKER/ WHITE
REAR VIEW
FLOW A to B
601659
A
601323
B
A
601323
CONNECTED TO MAIN VALVE BANK
A
B
601347
601323
601956
HOLDING TANK BOOM CYLINDERS
OUTER BOOM
INNER BOOM
6400 MODEL ONLY (4 VALVE MANIFOLD­CAP EXTRA VALVE PORTS, PARTS #601620 & #603035)
B
601724
602583
MUST BE NEAREST MANIFOLD
KIT #602434
602623
KIT #602708
602596
KIT #602708
3.00"x24"
602133
602133
FOLD OVER BOOM
602256
A
B
B
603035
602438
601749
601457
KIT #602708
601749
601457
602282
602596
602223
602438
3.00"x24"
601713
601477
601749
601749
601724
HOSE A
602583
601749
601457
C
602613
C
602613
INNER BOOM
3 ROW
602367
B
A
7
602241
HOSE A HOSE B HOSE C HOSE D HOSE E
6
601338
5
602247
4
601347
601338
HOSE D
HOSE E
A
B
Arrow
3
601749
602438
601457
HOSE C
601504
B
A
601504
ON MANIFOLD
601956
601338
2
601378
A
1
601338
601957
601338
601957
601446
601446
601957
601338
C 602613
OPTION HOLDING TANK BOOM
601048
601048
F
E
D
C
B
A
F
E
D
C
B
We reserve all rights in this document and in the informa­
tion contained therein. Reproduction, use or disclosure
to third parties without express authority is strictly
forbidden.
© SPUDNIK EQUIPMENT
Status
03­A
194068
Change
2
OP2
FUL
L S
KE
OP3
TRO
B
Name
EBH
Date
User
Proofed
Standard
194068
Suction2INC
731190
602577
602591
602701
602599
3
Origin
731130
194068
Suction2INC
Repl. f
731130
601687
4
601866
602598
602701
602701
194068
Suction2INC
Hose Kit 602759
PUMP MOUNTING BOLTS
#502656 QTY. REQ. 2
601994
B
C
HOSE CLAMP #981269
Date
10/20/11
C
1
2
A
601847
601467
HOSE CLAMP #981269
603077
LS
602569
602570
603078
731130
Suction2INC
602495
HP
RP
FA6137 Hyd MS­Drive w/Blower Drive Belt
COMPLETE HYDRAULIC UPDATE
1
194068
Sensor025INC
TEMP
NC
602524
LS
FA6157 Self Hydraulic Multi­Sep
602765
601389
601410
602239
1/2" HOSE
1
602334
A
601866
Repl. by
602721
601848
602009
601866
602701
601566
602009
602671
601376
601956
602678
194068
5
602207
601702
602755
602323
6
194068
Return125INC
731054
731171
602523
602506
602449
602598
731126
194068
Return075INC
601449
1/2" HOSE
602009
Drain05INC
7
731125
194068
602701
602883
602510
5PSI
8
Sheet 13
of 16
8
Print Date: 5/23/2012
3/4" HOSE
OPTION SIDE ELEVATOR DRIVE
6XXX­HARVESTERS­03­F
601373
602505
731054
SPUDNIK EQUIPMENT COMPANY LLC
584 W. 100 N.
BLACKFOOT,ID,83221
www.spudnik.com
601449
P1
P2
601715
A
602767
601993
7
SHUTTLE VALVE BODY #601714 QTY. REQ. 1
602449
PINCH ROLLER DRIVE
603008
601449
601449
SEGMENT DRIVE 602701
602760
731126
6
1/2" HOSE
602760
601847
Return075INC
602760
602722
601376
602720
601866
601866
602554
602701
602701
601713
Install plugs if NO hyd Blower Drive is configured
194068
Case075INC
5
601866 601848
601956
REV. VALVE MOUNTING BOLTS
#502727 QTY. REQ.4
601866
602767
B
1/4" HOSE
601338
3
2
1
4
601317
3
P
3
2
601713
2
603009
A
1
602589
A
B
A
T
602597
601866
601866
F
E
D
C
B
A
03­A
REVISION
D
C
B
A
602598
602889
602890
H
I
J
K
72
49
89
36
54
30
602689
602689
601776
601777
602693
602692
602598
602691
602603
602691
602758
601043
601043
601043
731142
DESCRIPTION OF REVISION
COMPLETE HYDRAULIC UPDATE
36
602689 168
602758
G
84
602689 168
602599
F
36
O
602691
E
40
86
N
602598
D
602432
601043
C
30
M
601043
B
32
(IN) 6400/6440
601486
601043
A
L
6200
601043
HOSE
168
168
78
94
54
102
36
84
72
84
54
36
86
74
N/A
(IN)
602495
LS
601467
ECN#
601417
2
DATE
10/20/11
602647
NAME
EBH
TEMP
NC
OP2
L S
KE
ORDR
CUST
B
3
602362
I
H
TRO
APPR RJB
DATE
FUL
OP3
602362
C
1
2
A
602053
ORIG
602877
602568
LS
602569
602570
602524
HP
RP
601819
1
OPTION
FA 5685
ELECTRIC SPEED CONTROL VALVE HYD BLOWER
INSTALL #602647 INSTEAD OF #602497
602671
601449
D
601756
731188
731053
731142
601681
601314
601314
731188
731188
A
B
601314
602683
191493
SUCTION­INT
602505
602506
602522
A
731142
601466
5PSI
602685
C
602548
731071
731142
731188
602505
602523
602506
G
5PSI602501
602504
30PSI
602499
B
4
3
601866
601993
L
602670
601637
602573
601848
F
602574
601851
602573
602496
601681
601314
601755
731144
SUCTION­INT
191493
731053
SHEET
OF 16
14
D
C
B
A
SPUDNIK EQUIPMENT COMPANY LLC
584W 100N
BLACKFOOT,ID,83221
www.spudnik.com
HP Port
RP Port
FUNCTION TEST
1) Lower Tractor RPM
­> Blower RPM should stay consistent above 600 PTO RPM
2) Increase Tractor RPM
3) Screw External Speed Control Valve out
­> Blower RPM should change
ALL­HARVESTERS­03­A
602510
1
2
A
4000 PSI
J
602574
601637
6
ADJUSTMENT PROCEDURE
1) Screw external Speed Control Valve complete in 2) Screw Pump Compensator out 3) Tractor PTO 800­1000RPM
4) Screw Pump Compensator in until Blower RPM reaches 1700 RPM, Maximum Pump Pressure is 3750 PSI.
601866
601866
601851
PRESSURIZED BREATHER
601314
602678
E
M
5
This drawing is the sole property of the above named. All rights of
the design and/or invention are reserved. No part of this document may be reproduced without prior written permission prior written permission
191493
Return
200.38748
B
C
602797
602500
C
601449
4000 PSI
K
4
602498
03­A
B
602376
A
Right Side
602679
Pressure Switch
602378
602376
A
B
602376
Left Side
602679
602003
602376
601457
602424
P
P
602677
3/4 x 348"
3/4 x 144"
602600
602323
601703­nut
601702
601847
601847
3/4 x 12"
602600
1/4 x 324"
602600
602755
DESCRIPTION OF REVISION
COMPLETE HYDRAULIC UPDATE
ECN#
DATE
10/20/11
601866
P
601866 B
A
T
601866
602688
NAME
EBH
SERVICE NOTE: ALWAYS RE­TORQUE WHEELS AFTER 2 HOURS OF OPERATION OR WHEELS WILL FALL OFF
P9 Pin 10­ N,C
Common­ Gnd
Resistor (12V (P9)­ P9 Pin 10)
REVISION
D
C
B
602467
1/2 x 354"
1/2 x 168"
602378
602467
602377
A
602924
602925
3/4 x 164"
602377
3/4 x324"
602263
3/4 x 12"
602671
602377
601457
602923
602926
2
601957
601340
ORDR
CUST
APPR
DATE
ORIG
A
601848
601848
3
X
601618
601618
601866
C
602377
2
1
602670
602377
601758
4
602757
3/4 x 126"
601880
3/4 x 240"
602757
3/4 x 126"
601880
602891
3/4 x 240"
602891
602891
3/4 x 240"
601880
5
602757
601866
602883
65 PSI check
602919
3/4 x 126"
This drawing is the sole property of the above named. All rights of
the design and/or invention are reserved. No part of this document may be reproduced without prior written permission prior written permission
ALL­HARVESTERS­03­A
601048
RETURN
SHEET
OF 16
15
PRESSURE
602810
602810
601048
D
C
B
A
SPUDNIK EQUIPMENT COMPANY LLC
584W 100N
BLACKFOOT,ID,83221
www.spudnik.com
­IF PRESSURE GOES TOO LOW, WHEEL DRIVE WILL AUTOMATICALLY ENTER "FREE­WHEELING" MODE.
603090
CASE DRAIN
602810
6
P7 Pin28
P1 Pin 27
P2 Pin 12
PRESSURE FWD COIL B REV COIL A CASE COIL C
RESULT
X
X
X
OUTPUT IS FWD PUSH
X
X
X
OUTPUT IS REV. PUSH
­SWITCH MUST BE PUSHED INTO FORWARD OR REVERSE AND HELD FOR
ONE SECOND TO ENGAGE WHEEL DRIVE.
ELEMENT#602330
602329
FILTER
601866
Y
602920
602467
601849
1
602701
602918
B
601457
602467 601892
F
E
D
C
B
We reserve all rights in this document and in the informa­
tion contained therein. Reproduction, use or disclosure
to third parties without express authority is strictly
forbidden.
© SPUDNIK EQUIPMENT
Status
03­A
4/4
3/4
B94.02240M
1/4 +12VDC(1)
1
COMPLETE HYDRAULIC UPDATE
Change
BLK
WHT
B94.02240M
1/4 +12VDC(1)
A
2
BLK
WHT
B94.02240M
1/4 +12VDC(1)
AUTO DEPTH
3/4
4/4
Date
10/20/11
SPEED SENSOR I
Name
EBH
BLK
WHT
B94.02240M
1/4 +12VDC(1)
RETURN TO
CENTER
11
10
9
8
7
6
5
4
NC
TABLE UP (3) CLTR UP
TABLE DN (3) CLTR DN
L COULTER UP
L COULTER DN
INNER BOOM UP
INNER BOOM DN
PWR DN MASTER UP [ROCK BOX]
3
Proofed RJB
Standard
User
Repl. f
ALL
12
MULTISEP REVERSE
Origin
13
ELEVATOR SLAVE [ROCK BOX SLAVE]
+12V
+12V
3
14
L LEVEL DN
HLT FAST FWD
15
L LEVEL UP
S1
S2
S3
S4
S5
GND
12V
12V
16
BLK
WHT
4
PRESSURE MULTISEP
Y1B DIGGER UP
1
17
NO(3)
18
NC(2)
Y1.2 DIGGER DN FLOAT BLK
WHT
602677
P
[HLT FOLD OVER DN]
4/4
Date 10/20/11
3/4
3/4
OPTION
Repl. by
P1
P2
P3
P4
­PCB­1
450233
P5
5
450234
SPUDNIK #402772
+12VDC
B94.01675
GND
4/4
OPTION
+12VDC
B94.01675
VIDEO
P10
CAM­1
GND
450116
WHT
31
R COULTER UP
R COULTER DN
OUTER BOOM UP
OUTER BOOM DN
STEER LEFT
STEER RIGHT
27
26
25
24
23
22
21
7
6XXX­HARVESTERS­03­F
1/4
3/4
+12V
+12V
TABLE IN
TABLE OUT
28
SHAKER DN
R LEVEL DN
OPEN CENTER
32
SHAKER UP
R LEVEL UP
33
29
SUPPORT WHEEL DN [­­SFWD]
34
30
[HLT FOLD OVER UP]
SUPPORT WHEEL UP [­­SBACK]
35
BLK
36
S6
S7
S8
S9
S10
2/4
6
1
Sheet 16
450195
2/3
3/3
1/3
B94.03482
OPTION
HOLDING TANK
SENSOR
8
OPTION
B94.02350
Return to Center
of 16
8
Print Date: 5/23/2012
450189
2/3
1/3
NC(2)
3/3
602524
GND
BLK
12V
4/4
12V
RED
P6
P7
P8
OPTION
R1.6K
SPEED SENSOR II
OPTION
B94.01675
4/4
+12V
+12V
TEMP HYDRAULIC BLOWER
TEMP
GRN
WHT
CAM­2
P9
GND
GND
SPUDNIK EQUIPMENT COMPANY LLC
584 W. 100 N.
BLACKFOOT,ID,83221
www.spudnik.com
+12V­BOX
OPTION
DATA­1
7
3/4
OPTION
DATA­2
B94.01675
6
B94.02240M
1/4 +12VDC(1)
5
SIG(3)
4
1­5V Out
REAR CROSS
SENSOR
REF­GND(2)
2/4
REF­GND(2)
2/4
REF­GND(2)
2/4
REF­GND(2)
2/4
3
+12VDC(1)
+12VDC(2)
B94.01675
2
GND­BOX
SIGNAL(2)
GND(1)
REF­GND(2)
2/4
8"­50"
0v
4..20mA
NC(4)
1
GND
UB
10­30V
GND(3)
F
E
D
C
B
A
Operator's Manual MODEL 5640
Spudnik Equipment Company, LLC.
584 W 100 N P.O. Box 1045
Blackfoot, ID 83221
(208) 785.0480 Fax (208) 785.1497
Delivery Declaration
Dear Spudnik Dealer,
The information below is required to activate the Spudnik warranty and to receive product updates.
Please fill out the letter below or email to [email protected] to register the recently sold machine.
Providing the customer name and address is optional and at your discretion. It will aid Spudnik in providing
product updates to your customer should the necessity arise. The serial number and date the machine was
delivered is mandatory.
Dealer Name_________________________Location____________________
Customer Name (or Business Name)
Street Address
City
State/Province
Serial Number
Post Code
Date of Delivery
Please mail to:
Spudnik Equipment Company, LLC
Attn: Warranty Administrator
PO Box 1045
Blackfoot, ID 83221
Or Fax to (208) 272-9853
If you have any questions, please call (208) 239-5791
Best Regards,
Spudnik Equipment Company, LLC.

Similar documents

model 6200 - Spudnik Digital Implements

model 6200 - Spudnik Digital Implements Welcome to the SPUDNIK line of potato handling equipment. We appreciate your decision to make our equipment a part of your operation, and look forward to a long term partnership. We strive to put t...

More information

Art.nr Beskrivning Pris ink.moms 02000 XZOTIC PAN ROCKR

Art.nr Beskrivning Pris ink.moms 02000 XZOTIC PAN ROCKR 2 163 kr 2 134 kr 898 kr 1 929 kr 331 kr 644 kr 1 837 kr 1 037 kr 8 100 kr 1 176 kr 310 kr 331 kr 662 kr 2 827 kr 835 kr 1 929 kr 1 732 kr 3 487 kr 5 906 kr 2 024 kr 2 587 kr 562 kr 1 687 kr 6 750 ...

More information