Air Systems - Tuffy Manufacturing

Transcription

Air Systems
Air Compressors
Nitrogen Tire Filling Systems
Air Hose & Reels
Air Preparation Products
Couplers & Plugs
Dry Air Systems
Hose Fittings
2007 Buyers Guide
Air Systems
13
Air Compressors
COMPRESSOR SELECTION GUIDE
Air Systems
Terminology
Sizing an Air Compressor
GENERAL DEFINITIONS
Compressors are machines for compressing air or gas from an
initial intake pressure to a higher discharge pressure.
Single-Stage Compressors are those in which compression
from initial to final pressure is completed in a single step or stage.
Two-Stage Compressors are those in which compressions
from initial to final pressure is completed in two distinct steps or
stages.
Intercoolers are devices for removing the heat of compression
of the air or gas between consecutive states of multistage
compressors.
Load Factor is the ratio of average compressor output during a
period of actual use to the continuous rated output of the
machine.
Piston Displacement (PD) is determined by precisely
measuring a volume of air which has been raised to a specific
pressure and is expressed in conditions existing at the
compressor discharge. This flow rate is generally stated in terms
of actual cubic feet per minute (CFM).
ACCESSORIES
Magnetic Starters provide thermal overload protection for
motors and are recommended for 3 HP and larger motors.
Aftercoolers/Dryers remove moisture from the air line as air
cools from compressor.
Automatic Tank Drain automatically removes water that has
accumulated in the compressor tank as air cools.
Low Oil Switch prevents the air compressor from operating
when oil is low.
1. List the types of pneumatic devices/equipment to be used and how many
will be used at the same time.
2. Add total of air volume (SCFM) required by pneumatic tools being used.
Utilize the chart below.
3. Add additional 25% to compensate for air line leaks and pressure drops.
4. Identify the air compressor that will provide necessary SCFM. The following professional electric 2-stage compressors provide the listed SCFM:
SCFM
HP
SCFM
HP
5 HP
16 SCFM
15 HP
42 SCFM
7.5 HP
24 SCFM
25 HP
97 SCFM
10 HP
32 SCFM
30 HP
106 SCFM
5. Once the correct HP rating has been selected based on the air volume
requirements, you will need to know the type of available electric service
to determine the need for a single phase or three phase compressor.
Tools Being Used
Tire Changer
1/2” Impact Wrench
Hydraulic Lift
SUBTOTAL
TOTAL SCFM
EXAMPLE
SCFM
5.5 SCFM
3.5 SCFM
7.5 SCFM
6.0 SCFM
22.5 SCFM
X 1.25%
28.125 SCFM
ANSWER
Customer will need an air compressor that produces a minimum of 28.125
SCFM @ 175 PSI. Customer will need a 10 HP compressor or two 5 HP
compressors.
AIR REQUIREMENT ESTIMATING GUIDE
After listing all the air operated devices to be supplied by the air compressor, determine from the chart, pressure range and volume of
air required by each device. The air compressor must maintain a minimum pressure at least equal to the highest of the pressure
ranges. Always use free air (CFM) and pressure (psi) from the nameplate on device or from manufacturer. Free air figures in the table
are averages and should not be considered accurate for any specific brand.
Air Consumption Chart for Automotive Service Shops
PSI
Tool
PORTABLE TOOLS
70-100
70-100
70-100
70-100
70-100
90-100
70-100
70-90
70-90
70-90
70-90
70-90
70-90
70-90
90-100
90-100
90-100
90-100
14
Air Filter Cleaner
Body Polisher
Body Sander
Brake Tester
Carbon Remover
Dusting Gun (Blow Gun)
Panel Cutter
Drill 1/16” to 3/8”
1” Impact Wrench
Die Grinder
Vertical Disc Sander
Small File/Saw Machine
Large File/Saw Machine
Burring Tool
CFM
PSI
Tool
SPRAY GUNS
3
20
10
4
3
3
4
4
3
4
5
8
12
5
20
3
5
5
90-100
90-100
90-100
125-150
125-150
125-150
125-150
125-150
Engine Gun
Paint Gun- Production
Paint Gun- Touch Up
Rim Stripper
Tire Changer
Tire Inflation Line
Tire Spreader
Vacuum Cleaner
5
8
4
6
1
2
1
90-100
90-100
125-150
90-100
90-100
90-100
70-100
70-100
70-100
Air Hammer
Tire Hammer
Pneumatic Garage Door
Radiator Tester
Spark Plug Cleaner
Spark Plug Tester
Transmission/Differential Flusher
Fender Hammer
Car Washer
4
12
3
1
5
1
3
9
9
Air Systems
HAMMERS
2007 Buyers Guide
CFM
7
Air Compressors
INDUSTRIAL AIR COMPRESSORS
Quincy Air Master Air Compressors
Air Systems
Quincy Air Master air compressors are designed for maximum productivity and efficiency. Quincy Air Master leads the industry with
most CFM per brake horsepower, ensuring more air while consuming less energy in the production process. Quincy Air Master offers
a full line of reciprocating compressors up to 30 HP. Ask your Ascot
representative for details.
Standard Features
•
•
•
•
•
•
•
•
•
•
Heavy duty cast iron crankcase and cylinders
ODP motors
High-efficiency intercoolers
Splash lubrication
Oil sight glass (5, 7.5 and 10 HP)
Discharge line unloader on gasoline powered units
Kohler and Honda engines with low oil sentry
Dual control standard on 15 HP units and up
Factory fill of Quin-Cip lubricant
One year on-site warranty
101-21512
Options
•
•
•
•
•
•
•
•
•
•
5 HP combination pressure switch/starter
208/230/460 volt starters
TEFC motors
Filter/silencers
Factory installed air cooled aftercoolers
Pneumatic electronic tank drains or
Vibration isolators
Low oil level shutdown
Optional two-year warranty
Refrigerated air dryers and filters
Ascot
No.
101-24160
101-24180
101-24181
101-25180
101-25181
101-25380
101-25381
101-27180
101-27181
101-27120
101-27380
101-27381
101-27312
101-21080
101-21012
101-21380
101-21580
101-21512
Mfg. Model
No.
241C60VCAB
241C80HCAB
241C80VCAB
251C80HCAB
251C80VCAB
253D80HCAB
253D80VCAB
271C80HCAB
271C80VCAB
271C120VCAB
273D80HCAB
273D80VCAB
273D120VCAB
P2103D80HCAB
P2103D12HCAB
2103D80VCAB
2153D80HCA
2153D12HCA
2-Year Warranty Program
Industrial Reciprocating Products - QR-25, QT & PLT Services
2-Stage Compressor
A two-year warranty is available for the basic compressor by purchasing
warranty maintenance kits. The warranty maintenance kits contain lubricant, filter(s) and registration information for two years.
Your basic compressor will have the same coverage for the second year
as it had for the first. You simply follow the recommended maintenance
spelled out in the instruction manual. The two-year warranty only applies
when the maintenance kits is purchased and registered within thirty days
of compressor purchase.
HP
(Gal.)
5
5
5
5
5
5
5
7.5
7.5
7.5
7.5
7.5
7.5
10
10
10
15
15
Tank Size
Phase
60 Vertical
80 Horizontal
80 Vertical
80 Horizontal
80 Vertical
80 Horizontal
80 Vertical
80 Horizontal
80 Vertical
120 Vertical
80 Horizontal
80 Vertical
120 Vertical
80 Horizontal
120 Horizontal
80 Vertical
80 Horizontal
120 Horizontal
1
1
1
1
1
3
3
1
1
1
3
3
3
3
3
3
3
3
2007 Buyers Guide
Air Systems
CFM
175 Psi.
16.3
16.3
16.3
17.2
17.2
17.2
17.2
22.6
22.6
22.6
22.6
22.6
22.6
35.0
35.0
35.0
52.5
52.5
Max
Psi.
175
175
175
175
175
175
175
175
175
175
175
175
175
175
175
175
175
175
Wt.
(Lbs.)
500
540
580
540
580
540
580
560
580
700
560
580
700
800
850
1000
960
995
RPM
914
914
914
942
942
942
942
1034
1034
1034
1034
1034
1034
1000
1000
1000
950
950
15
Air Compressors
Quincy Air Master Complete Compressed Air System (CCAS)
Air Systems
Quincy Air Master Complete Air System (CCAS) is ideal when the
application requires cool, clean, dry air. The CCAS horizontal units are equipped
with the following standard features, pre-wired and/or pre-piped to the unit:
• Moisture separator
• Filter/silencer
• Magnetic starter
• Pneumatic drain
• Aftercooler
• Particulate prefilter
• Refrigerated air dryer
• Coalescing afterfilter
*Vibration isolators and oil & water separator are shipped loose (not wired or piped)
Ascot
No.
101-25183
101-25382
101-25383
101-25384
101-27182
101-27382
101-27383
101-27384
101-27322
101-27323
101-27324
101-21011
101-21031
101-21032
101-21046
101-21023
101-21026
101-21531
101-21532
101-21546
101-21520
101-21523
101-21536
Mfg. Model
No.
25180HATP23
25380HATP20
25380HATP23
25380HATP46
27180HATP23
27380HATP20
27380HATP23
27380HATP46
27312HATP20
273120HATP23
273120HATP46
2101120HATP23
2103120HATP20
2103120HATP23
2103120HATP46
2103200HATP23
2103200HATP46
2153120HATP20
2153120HATP23
2153120HATP46
2153200HATP20
2153200HATP23
2153200HATP46
HP
5
5
5
5
7.5
7.5
7.5
7.5
7.5
7.5
7.5
10
10
10
10
10
10
15
15
15
15
15
15
CFM @
175 psig
17.2
17.2
17.2
17.2
22.4
22.6
22.6
22.6
22.6
22.6
22.6
35.0
35.0
35.0
35.0
35.0
35.0
52.5
52.5
52.5
52.5
52.5
52.5
Phase
Single
Three
Three
Three
Single
Three
Three
Three
Three
Three
Three
Single
Three
Three
Three
Three
Three
Three
Three
Three
Three
Three
Three
Volt
(Gal.)
230
208
230
460
230
208
230
460
208
230
460
230
208
230
460
230
460
208
230
460
208
230
460
GAS-DRIVEN, TWO-STAGE INDUSTRIAL AIR COMPRESSORS
• Highly Efficient-Leading the industry with more CFM per brake hp
• Lasting Performance-Heavy duty, cast iron construction ensures
durability
• Enhanced Details-State-of-the-art design and virtually maintenance free
• Complete Confidence-Full, two-year warranty available
Pressure lubricated 11 HP and 13 HP models are available.
Ascot
No.
102-21130
102-21131
102-21230
102-21860
16
Mfg. Model
No.
G211K30HCD
G211H30HCB
G212K30HCD
G218K60HCA
HP
Engine
11
11
13
18
Kohler
Honda
Kohler
Kohler
Air Systems
Tank Size
(Gal.)
30
30
30
60
CFM @
175 psig
18.5
19.6
23.4
37.4
2007 Buyers Guide
Wt.
(Lbs.)
430
430
430
825
Tank
80
80
80
80
80
80
80
80
120
120
120
120
120
120
120
200
200
120
120
120
200
200
200
Air Compressors
Two-Stage Gasoline Engine Driven
Ideal for fleet or field service applications with truck bed mounting design. Idle engine control
and electronic ignition for easier starting. Powder coat paint finish to protect against outdoor
elements. 30 gallon ASME receiver and OSHA fully enclosed belt guard for worker safety.
Model No.
102-24125 2475F12.5G
102-24115 2475F11.5GKA
102-24212 2475F13.GH
HP
Engine
12.5
11.5
11
Kohler
Kawasaki
Honda
ACFM@
175 PSIG
24
25
19
Tank
Air Systems
Ascot No.
30 Gallon Horizontal
Two-Stage Electric “Value Packages”
Priced right and designed for the most demanding applications where a dependable air supply
is required. Each package includes a two-stage cast iron compressor pump, ODP electric motor,
magnetic motor starter (mounted and wired), automatic start and stop pressure switch control,
mounted on an ASME rated receiver tank. Available voltages: 230/1/60 (5-7.5 HP), 200/3/60,
460/3/60. Pressure up to 175 PSIG. Oil sight glass included on 10-15 HP Packages.
Ascot No.
Model No.
HP
101-23451
101-24705
101-24751
101-25452
101-71150
2340L5
2475N5
2475N7.5
2545E10-V
7100E15-V
5
5
7.5
10
15
ACFM@
175 PSIG
15
16.8
24
35
50
Tank
60 Gallon Vertical
80 Gallon Vertical
80 Gallon Vertical
Two-Stage Electric “Fully Packaged”
Everything you need for a dependable air supply with minimal maintenance. Fully packaged
compressors include magnetic motor starter, air cooler and electric drain valve which removes
harmful moisture, plus, the added protection of a low oil level shutdown switch. Available
voltages: 230/1/60 (5-7.5 HP), 200/3/60, 460/3/60.
Ascot No.
Model No.
HP
101-27550
101-27551
101-27552
101-27553
101-71153
2475N-FP
2475N7.5-FP
2545K10-V
2545E10-V
7100E15-V
5
7.5
10
10
15
ACFM@
175 PSIG
16.8
24
35
35
50
Tank
80 Gallon Vertical
80 Gallon Vertical
120 Gallon Vertical
Ingersoll-Rand Start-Up Maintenance Kits
Ascot No.
106-24305
106-24710
106-30020
106-24712
All the parts needed to maintain your compressor for
a full year, plus the added protection of extended
warranty coverage are two very distinct advantages
you’ll gain with the All Season Select synthetic pump
lubricant and replacement air filter elements. Kits for
gasoline engine driven compressors also include
engine air filter, oil filter and engine oil.
2007 Buyers Guide
Air Systems
Model No.
32305880
32305898
32305906
32305872
Compressor HP
5 & 7.5
10 & 15
20, 25 & 30
12.5 (Kohler)
17
Air Compressors
ROTARY SCREW COMPRESSORS
Air Systems
Rotary Screw Compressors
• Engineered for high performance, efficiency and reliability, Chicago
Pneumatic’s new line of QRS rotary screw air compressors meet the
compressed air requirements of the most demanding shops, providing
a complete compressed air installation. The compressor and dryer,
when included, is tank mounted, prepiped, wired and tested. All air
connections have been optimized to minimize pressure drop and
reduce the potential for air leaks
• Low sound enclosure and innovative cooling fan, the CP QRS series
offers the lowest noise levels available, allowing you to install it
virtually anywhere in the shop
• Combined with efficient rotary screw technology and a high efficiency
TEFC (totally enclosed fan cooled) motor, the QRS offers low energy
consumption. Pulse free air is ideal for paint and body applications.
• Simple compression concept and continuous contact cooling, the
QRS rotary screw compressor can operate fully loaded- 24 hours a
day/7 days a week. All reciprocating compressors are designed to
cycle for intermittent operation
• Can easily be installed just about anywhere in the shop. Its integrated
design provides clean, cool, dry, quality air that protects your air tools,
shop equipment and body work from harmful moisture, dirt and heat.
The QRS oil cooling system, A-T-L starter, TEFC motor, optional air
dryer, low sound enclosure and receiver tank are all factory
assembled and tested
• No wearing parts, the CP QRS offers increased reliability, reduced
maintenance and trouble-free operation. No need to worry about
rings, valves, rod inserts, bushings and pistons. Extended
service intervals save time and money. Convenient service panel
allows easy access to all internal components
• QRS 3.0, 5.0 & 7.5 are available 1/60/220V
• All QRS are available with tri-voltage motors and starters for
3/60/208-230-460V
• QRS 20-30 are also available as base mounted (separate tank)
• HPD Model includes dryer
Ascot
No.
101-30000
101-50000
101-75000
101-10000
101-15000
101-20000
101-25000
101-30000
Mfg. Model
No.
QRS3.0
QRS5.0
QRS7.5
QRS10
QRS15
QRS20
QRS25
QRS30
HP or HPD
CFM@Max PSI
3
5
7.5
10
15
20
25
30
8.5
16.6
21.2
37/33
52/47
84/76
101/92
119/107
Max Pressure
(PSIG)
150
150
125/150
125/150
125/150
125/150
125/150
HP Model
HPD Model
Horizontal
Tank (GAL)
60
60
60
120
120
120
120
120
dbA Enclosed
Dimensions
61
62
64
66
68
72
73
74
56”x22”x50”
56”X22”X50”
56”X22”X50”
73”X24”X58”
73”X24”X58”
73”X24”X60”
73”X24”X60”
73”X24”X60”
*HPD Model includes dryer - Call For More Details!
18
Air Systems
2007 Buyers Guide
Net Wt. (LBS)
(w/or w/o Dryer)
463/485
463/485
468/490
775/845
815/885
1135/1201
1157/1223
1234/1300
NITROGEN TIRE FILLING SYSTEMS
How nitrogen works and what it does:
Nitrogen is a dry, inert gas used to inflate airplane tires, off-road truck tires, military vehicle tires and race car tires for improved performance. Oxygen in compressed air permeates through the wall of the tire reducing the tires inflation pressure. During its journey through the
tire wall, oxygen oxidizes the rubber compounds in the tire, causing under inflation and deteriorated rubber. Dry nitrogen will prevent rim
corrosion and helps the tire to run cooler.
Model TS24CTD
Model TS02RTD
Air Systems
(Floor Standing)
(Receiving tank and
prefilters not shown
but included)
Model TS06, TS12, TS18
(Wall Mount)
(Wall Mount)
Nitrogen Tire Filling System
• Produces high purity nitrogen from compressed air
• Requires simple wall mount installation (floor standing model also available)
• Allows inflation of up to 32 truck tires per hour
• Requires no storage of nitrogen
• Operates in the low pressure range up to 150 psig
• Inflates tires at the same rate as compressed air
• Includes two stages of high efficiency prefiltration and oil removal filtration
• Extends tire life by up to 25%
• Improves fuel efficiency by up to 3.3%
• Provides more consistent tire pressure
• Prevents auto-ignition of tires
• Eliminates rim corrosion
• Results in tires operating at lower temperature
• Includes 60 Gallon Tank (Larger Tanks Available)
Ascot
No.
Mfg. Model
No.
Nitrogen
Purity
Nitrogen
Capacity
Tire Inflation Capacity
Car / Truck
Compressed Air Generator
Pressure Req. Dimensions
Storage Tank
Dimensions
119-00200
TS02RTD
95%
1.75 SCFM
100-145 PSIG
32”x19”x5”
40”x18” Dia
119-00600
TS06RTD
95%
6 SCFM
145-189 PSIG
33”x10”x6”
40”x18” Dia
119-01200
TS12CTD
95%
12 SCFM
145-189 PSIG
33”x22”x6”
40”x18” Dia
119-01800
TS18CTD
95%
17.5 SCFM
145-189 PSIG
33”x22”x6”
40”x18” Dia
119-02400
TS24CTD
95%
34 SCFM
30 Tires/Hr (195/65R15)
N/A
90 Tires/Hr (195/65R15)
12 Tires/Hr (11R22.5)
24 Tires/Hr (11R22.5)
36 Tires/Hr (11R22.5)
68 Tires/Hr (11R22.5)
145-189 PSIG
69”x24”x20”
40”x18” Dia
*RTD includes retail tire dealer start-up kit
*CTD includes commercial tire dealer start-up kit
Maintenance Kits
Ascot No.
119-09000
119-90010
119-90011
119-90012
119-24000
Mfg. Model No.
MK-L9000
MK-L9001
MK-L9001
MK-L9001
MK-TS24CTD
Nitrogen Generator Model
TS02RTD
TS06RTD
TS12RTD
TS18CTD
TS24CTD
2007 Buyers Guide
Portable Nitrogen Units Available
Nitrogen Hose Reels, See pg 29
Nitrogen Caps See pg 120
Air Systems
19
Air Systems
NITROGEN TIRE FILLING SYSTEMS
RTI NTF-60 Plus Nitrogen Tire Filling System
RTI NTF-15 Nitrogen Tire Filling System
The NEW RTI NTF- 60 Plus generates nitrogen on demand and stores it on-board for
quick nitrogen tire service. The exclusive
RTI tire deflation and vacuum system
increases speed and ensures higher
nitrogen purity in tires. A purity tester quickly
checks nitrogen purity. The NTF-60 provides
your customers with better tire pressure,
increased safety, superior handling,
improved fuel economy and longer tire life!
Purity tester 436050 included.
The NEW RTI NTF-15 Nitrogen Tire Filling System
generates nitrogen on demand and stores
it on-board for quick nitrogen tire
service. The exclusive RTI tire deflation and vacuum system increases
speed and ensures higher nitrogen
purity in tires. A purity tester quickly
checks nitrogen purity. The NTF-15
provides your customers with better tire
pressure, increased safety, superior
handling, improved fuel economy and
longer tire life! Purity tester 436050 included.
• Service Time* – <4 minutes average
(per vehicle)
• Maximum Services* – 32 tires (8 vehicles) (per hour including
tank refill)
• Tank Size – 60 gallon (227 L)
Ascot No.
119-00015
119-00115
*Maintenance Kits Available, Call for Details
*average tire size for data: 225/60/R15
Ascot No.
119-00060
Mfg. No.
Nitrogen Capacity
NTF-15
2.1CFM
NTF-15 Plus 5.1CFM
Mfg. No.
Nitrogen Capacity
NTF-60 Plus 5.1CFM
Nitrogen Generator
• No extra filling time compared to compressed air
• No air consumption when not in operation, nitrogen created on demand
provided energy savings
• Can be connected directly to existing compressed air lines
• Delivers high quality nitrogen at the purity required for tire inflation
• Onboard nitrogen analyzer for easy testing
• Non-degrading membrane technology, 5 year standard warranty
• Compact design for minimum space requirements
• Minimum filter maintenance
• Quiet operation
• 24 X 7 customer support
• Configurable and Upgradeable product - can be upgraded while in use!
Ascot No.
119-20406
119-20808
119-21208
119-21612
Mfg. Model
No.
N20406-PG
N20808-PG
N21208-PG
N21612-PG
CFM N2
4
8
12
16
Outlet
Pressure (PSI)
130-145
130-145
130-145
130-145
N2 Purity
95%
95%
95%
95%
Receiving Tank
Capacity (Gal.)
60
80
80
120
Dimensions
25.75”x52.38”x35.12”
28.96”x51.89”37.55”
28.96”x51.89”x37.55”
28.96”x74.31”x37.52”
Nitrogen Purity Tester
Aluminum N2 Valve Caps
Convenient and reliable hand-held device.
Quickly and accurately tests nitrogen tank purity and
accurately tests tire purity. Provides your
customers with a professional display, validating your serice.
• High quality green stamped chrome N2
valve stem caps provide a great reminder
that tires are filled with nitrogen.
• 200 Per Box
Ascot No.
119-43605
Ascot No.
468-43607
20
Mfg. No.
436050
Air Systems
Mfg. No.
436075
Qty/Box
200
2007 Buyers Guide
BUILDING AN EFFICIENT AIR SYSTEM
Water and dirt cause more problems in compressed air lines than anything else. A typical 7.5 HP compressor brings in an average of
3 gallons of water from the atmosphere per day along with dust and dirt. It is important to eliminate water and dirt from your air system.
A good filtration system will extend the life of your tools and eliminate downtime and unnecessary service calls on your equipment.
Air Systems
5 Important Steps to a Work Station Drop
1. Main line filter and regulator should be placed at least 20 feet from the
compressor. The air will cool down, allowing much of the water vapor to
condense naturally for removal by filtration.
2. Main line piping should slope down from point of origin by 1/8” per foot. Any
water in the line will flow down to the lowest point for draining.
3. All line drops (work stations) should be taken from the top of the main line.
This prevents water which forms in the main line from flowing into branch
lines.
4. Galvanized pipe is recommended when building an air system.
5. Follow illustration when building a work station drop.
2007 Buyers Guide
Slope main line 1/8" per foot
away from compressor. Use
galvanized pipe.
Drop a 6" pipe
to drip leg.
Air Systems
Goose-neck all
work stations.
Place a "T" whereever filter goes.
Place a drain trap at low points to remove water.
Also utilize on main line at low points.
21
AIR PREPARATION ACCESSORIES
Automatic Drain
Air Systems
Electric Automatic Compressor Drain
• Automatically drains filters, compressor
tanks, drip legs, aftercoolers and receivers
• Opens and closes valve in 1 to 60 minute
cycle times and 1 to 30 second blow down
time
• 1/4” NPT connection
• Includes Y-strainer
Ascot No.
117-05702
Mfg. No.
5702S
Description
Electric Automatic Compressor Drain
• Automatically expels liquids
from piping network in
compressed air systems
• Use in low spots in an air system
where water accumulates
• Float type drain features a
protective stainless steel screen
with umbrella baffle, providing
large sump area for oil, sludge and
dirt
• 1/2” NPT top threaded port
Mini In-Line Disposable
Desiccant Dryer
Ascot No.
117-05304
• Point-of-use, patented, disposable,
mini in-line desiccant dryer
removes water vapor, oil vapor and dirt
• Point-of-use on blow guns or spray guns as final protection for
critical parts during blow off and paint spraying
• See-through housing shows desiccant bead color change from
blue to pink indicating dryer needs to be replaced
• 1/4” NPT connection
Ascot No. Mfg. No.
117-00010 DFD-10
Description
Disposable Desiccant Dryer
Qty.
2
Mfg. No.
T53-04W
Description
Automatic Drain
In-Line Air Tool Filter
• In-line filter protects air tools from dirt
and debris
• 1-9/16” length, 1/2 oz.
• 40 micron sintered bronze element
• Inlet can be attached directly to
pneumatic tools
• 1/4” male x 1/4” female NPT
Ascot No.
117-09132
Mfg. No.
9132
Description
In-Line Air Tool Filter
COMPRESSED AIR SYSTEM WATER FACTOR CHART
Follow the steps below to determine the gallons of water
EXAMPLE
accumulated by a compressed air system per 8 hours of
use:
25 HP air compressor delivers 100 scfm.
Ambient Temperature = 100° F
Relative Humidity = 60%
1
2
3
Determine the ambient temperature (outside
temperature surrounding the dryer) and relative
humidity.
Locate ambient temperature in first column of water
factor chart.
Follow the row over to percent of humidity. This
indicates the number of gallons accumulated by your
air compressor in an 8-hour period.
Water factor chart number is 31.2
COMPRESSED AIR SYSTEM ACCUMULATES 31.2
GALLONS OF WATER PER 8 HOURS OF USE.
Gallons of Water per 8 Hours @ 100 scfm
Ambient Air
Temperature
120° F
110° F
100° F
90° F
80° F
70° F
60° F
50° F
40° F
30° F
20° F
10° F
22
20%
Humidity
18.6
14.1
10.5
7.8
5.7
3.9
2.7
2.1
1.2
.9
.6
.3
30%
Humidity
27.9
21.0
15.6
11.4
8.4
6.0
4.2
3.0
2.1
1.2
.9
.5
40%
Humidity
37.2
27.9
20.7
15.3
11.1
7.8
5.7
3.9
2.7
1.8
1.2
.7
50%
Humidity
46.5
35.1
26.1
19.2
13.8
9.9
6.9
4.8
3.3
2.1
1.5
.8
Air Systems
60%
Humidity
55.8
42.0
31.2
23.1
16.8
12.0
8.4
6.0
3.9
2.7
1.7
1.0
70%
Humidity
65.1
48.9
36.6
26.7
19.5
13.8
9.9
6.9
4.8
3.0
1.9
1.2
80%
Humidity
74.4
55.8
41.7
30.6
22.2
15.9
11.1
7.8
5.4
3.6
2.1
1.4
2007 Buyers Guide
90%
Humidity
83.7
63.0
46.8
34.5
24.9
18.0
12.6
8.7
6.0
3.9
2.4
1.5
100%
Humidity
93.0
69.9
52.2
38.4
27.9
19.8
14.1
9.9
6.6
4.5
2.7
1.8
FILTERS, REGULATORS, LUBRICATORS
Filter/Regulator Combination Units
•
•
•
•
*NOTE: Gauge not included. Sold separately. Ascot part number indicated.
114-75301
Ascot
No.
114-75200
114-75201
114-75202
114-75203
114-75300
114-75301
114-75302
114-75303
114-00754
114-75400
114-75401
114-75402
114-75403
Model Pipe
No.
Size
B752T 1/4”
B752WT 1/4”
B752FW 1/4”
B752Z 1/4”
B753T 3/8”
B753WT 3/8”
B753FW 3/8”
B753Z 3/8”
B754GW 1/2”
B754T 1/2”
B754WT 1/2”
B754FW 1/2”
B754Z 1/2”
Adjustment
Type
T-Handle
T-Handle
Knob
Knob
T-Handle
T-Handle
Knob
Knob
Knob
T-Handle
T-Handle
Knob
Knob
Max. Flow
SCFM
50
50
50
50
80
80
80
80
100
100
100
100
100
Bowl
Capacity
5 oz.
6 oz.
6 oz.
5 oz.
5 oz.
6 oz.
6 oz.
5 oz.
6 oz
5 oz.
6 oz.
6 oz.
5 oz.
Bowl
Type
Poly
Metal
Metal
Poly
Poly
Metal
Metal
Poly
Metal
Poly
Metal
Metal
Poly
Gauge
Drain
Part No.
Manual
117-01481*
Manual
117-01481*
Float Auto 117-01481*
Piston Auto 117-01481*
Manual
117-01481*
Manual
117-01481*
Manual
Included
Manual
117-01481*
Manual
117-01481*
Operating
Temperature
40-125° F
40-175° F
40-125° F
40-125° F
40-125° F
40-175° F
40-125° F
40-125° F
40-175° F
40-125° F
40-175° F
40-125° F
40-125° F
Max.
Pressure
150 psig
250 psig
175 psig
150 psig
150 psig
250 psig
175 psig
150 psig
250 psig
150 psig
250 psig
175 psig
150 psig
Modular Units
• Units include a filter, regulator and lubricator and or filter,
regulator and oil removing filter
• Units equipped with or without OSHA safety lock-out valves
• Gauge included
• Screwdriver only tool needed to connect or disconnect units
• Insert interlocking feature allows simple installation in any location
114-03354
Ascot
No.
114-03352
114-13352
114-03353
114-13353
114-03354
114-13354
Model
Pipe
No.
C33352W 1/4”
VC33352W 1/4”
C33353W 3/8”
VC33353W 3/8”
C33354W 1/2”
VC33354W 1/2”
Max. Flow
Size
100
100
100
100
100
100
Bowl
SCFM
6 oz.
6 oz.
6 oz.
6 oz.
6 oz.
6 oz.
Bowl
Capacity
Metal
Metal
Metal
Metal
Metal
Metal
2007 Buyers Guide
Type
Manual
Manual
Manual
Manual
Manual
Manual
Lockout
Drain
Not Included
Included
Not Included
Included
Not Included
Included
Air Systems
Operating
Valve
40-175° F
40-175° F
40-175° F
40-175° F
40-175° F
40-175° F
Max.
Temperature
250 psig
250 psig
250 psig
250 psig
250 psig
250 psig
23
Air Systems
Combines filter and pressure regulator into one space saving unit
Output performance equal to an individual filter and regulator
Reduced pressure outputs of 0-125 psig
Features three position non-rising knob—push to lock, pull to adjust,
detach to make tamper resistant
• Available in metal bowl or polycarbonate bowl with metal bowl
guard
FILTERS
Air Systems
General Purpose Filters
• Removes harmful water condensate, pipe scale, dirt and rust from your
compressed air system
• Prevents corrosive damage to compressed
air equipment and finished products
• Protects components and air tools from premature failure
• Installed upstream of regulators to prevent valve failure
• Also used as pre-filters to oil removing and coalescing filters to ensure
high efficiency and long element life in applications such as paint
spraying, instrumentation and pharmaceuticals
• Porous sintered bronze element
Ascot
No.
111-30002
111-35200
111-35201
111-35202
111-35203
111-35300
111-35301
111-35302
111-35303
111-35400
111-35401
111-35402
111-35403
111-37600
111-37601
111-32908
Model
No.
F300-02
F352
F352W
F352Z
F352FW
F353
F353W
F353Z
F353FW
F354
F354W
F354Z
F354FW
F376W
F376FW
F329-08
Pipe
Size
1/4”
1/4”
1/4”
1/4”
1/4”
3/8”
3/8”
3/8”
3/8”
1/2”
1/2”
1/2”
1/2”
3/4”
3/4”
1”
Max. Flow
SCFM
27
48
48
48
48
75
75
75
75
100
100
100
100
230
230
300
Bowl
Capacity
1 oz.
5 oz.
6 oz.
5 oz.
6 oz.
5 oz.
5 oz.
6 oz.
6 oz.
5 oz.
6 oz.
5 oz.
6 oz.
10 oz.
10 oz.
29 oz.
Bowl
Type
Poly
Poly
Metal
Poly
Metal
Poly
Metal
Poly
Metal
Poly
Metal
Poly
Metal
Metal
Metal
Metal
111-30002
Operating
Drain
Manual
Manual
Manual
Piston Auto
Float Auto
Manual
Manual
Piston Auto
Float Auto
Manual
Manual
Piston Auto
Float Auto
Manual
Float Auto
Manual
111-35201
Max
Temperature
40°-125°F
40°-125°F
40°-160°F
40°-125°F
40°-120°F
40°-125°F
40°-160°F
40°-125°F
40°-120°F
40°-125°F
40°-160°F
40°-125°F
40°-120°F
40°-160°F
40°-120°F
40°-160°F
111-32908
Filter
Flow
150 psig
150 psig
250 psig
150 psig
175 psig
150 psig
250 psig
150 psig
175 psig
150 psig
250 psig
150 psig
175 psig
250 psig
175 psig
250 psig
115-55301
Coalescing/Oil Removing Filters
Element
20 micron
40 micron
40 micron
40 micron
40 micron
40 micron
40 micron
40 micron
40 micron
40 micron
40 micron
40 micron
40 micron
40 micron
40 micron
40 micron
115-57601
• Removes submicron particles, particularly oil
• Applications include paint spraying, pneumatic control instrumentation, printing and protection of air
bearings
• For maximum efficiency, a pre-filter needs be to installed upstream of oil-removing filter
• Bonded end seals eliminate aerosol leakage past the element
• Inner and outer support ribs are chemical resistant and strengthen element structure
• Drain layers allow filtered elements to drop to bottom of filter with barrier to prevent reentry of drops to
downstream air
Ascot
No.
115-55200
115-55201
115-55300
115-55301
115-55400
115-55401
115-57601
115-50508
115-50810
115-50812
24
Model
No.
F552FW
F552W
F553FW
F553W
F554FW
F554W
F576W
F508-08W
F508-10W
F508-12W
Pipe
Size
1/4”
1/4”
3/8”
3/8”
1/2”
1/2”
3/4”
1”
1-1/4”
1-1/2”
Max. Flow
SCFM
24
24
37
37
37
37
60
300
300
400
Bowl
Capacity
6 oz.
6 oz.
6 oz.
6 oz.
6 oz.
6 oz.
10 oz.
29 oz.
60 oz.
60 oz.
Bowl
Type
Metal
Metal
Metal
Metal
Metal
Metal
Metal
Metal
Metal
Metal
Air Systems
Drain
Float Auto
Manual
Float Auto
Manual
Float Auto
Manual
Manual
Manual
Manual
Manual
Operating
Temperature
40°-120°F
40°-160°F
40°-120°F
40°-160°F
40°-120°F
40°-160°F
40°-160°F
40°-160°F
40°-160°F
40°-160°F
2007 Buyers Guide
Max
Pressure
175 psig
250 psig
175 psig
250 psig
175 psig
250 psig
250 psig
250 psig
250 psig
250 psig
Filter
Element
.03 micron
.03 micron
.03 micron
.03 micron
.03 micron
.03 micron
.03 micron
.03 micron
.03 micron
.03 micron
REGULATORS & LUBRICATORS
Regulators
112-00262
Ascot
No.
112-00162
112-00262
112-00352
112-00353
112-00354
112-00376
112-00378
112-03910
112-03912
Model
No.
R162
R262**
R352
R353
R354T
R376T
R378T
R3910
R3912
112-00352*
Pipe
Size
1/4”
1/4”
1/4”
3/8”
1/2”
3/4”
1”
1-1/4”
1-1/2”
112-00378*
Max. Flow
SCFM
25
25
50
80
100
220
250
700
700
*NOTE: Gauge not included. Sold separately. Ascot part number indicated.
Adjustment
Type
Adjustment Knob
Adjustment Knob
Adjustment Knob
Adjustment Knob
T-handle
T-handle
T-Handle
T-Handle
T-Handle
Pressure
Gauge Part No.
117-01681*
117-01681*
117-01481*
117-01481*
117-01481*
117-01481*
117-01481*
117-01481*
117-01481*
Gauge
Port
1/8” NPT
1/8” NPT
(2) 1/4” NPT
(2) 1/4” NPT
(2) 1/4” NPT
(2) 1/4” NPT
(2) 1/4” NPT
(2) 1/4” NPT
(2) 1/4” NPT
Operating
Temperature
40°-120°F
40°-120°F
40°-120°F
40°-120°F
40°-120°F
40°-120°F
40°-120°F
40°-120°F
40°-120°F
Operating
Pressure
5 to 125 psig
5 to 125 psig
5 to 125 psig
5 to 125 psig
5 to 125 psig
5 to 125 psig
5 to 125 psig
5 to 125 psig
5 to 125 psig
Lubricators
113-00353
Ascot
No.
113-00352
113-01352
113-00353
113-01353
113-00354
113-01354
113-00376
• Injects a fine stream of oil into the air stream to automatically lubricate air operated
tools and other devices
• Extends life of downstream components
• Precise control of oil feed with needle valve adjustment knob
• Adds minimal pressure drop to the air system
• Features three position non-rising knob—push to lock, pull to adjust, detach to make
tamper resistant
• High air flow
• Precise visual adjustment control
• Low flow to establish drip rate
• W is with sight glass and metal bowl
113-01353
Model
No.
L352
L352W
L353
L353W
L354
L354W
L376W
Pipe
Size
1/4”
1/4”
3/8”
3/8”
1/2”
1/2”
3/4”
Max. Flow
SCFM
16
16
82
82
142
142
142
Bowl
Capacity
5 oz.
5 oz.
5 oz.
5 oz.
5 oz.
5 oz.
10 oz.
Bowl
Type
Poly
Metal
Poly
Metal
Poly
Metal
Metal
Operating
Temperature
40°-125°F
40°-175°F
40°-125°F
40°-175°F
40°-125°F
40°-175°F
40°-125°F
Max
Pressure
150 psig
200 psig
150 psig
200 psig
150 psig
200 psig
150 psig
Oil
Delivery
2 scfm
2 scfm
2 scfm
2 scfm
2 scfm
2 scfm
2 scfm
CALL FOR DETAILS ON REPLACEMENT PARTS ON ALL AIR PREPARATION PRODUCTS.
2007 Buyers Guide
Air Systems
25
Air Systems
• Specialized control valve reduces upstream supply pressure level to
a specified constant downstream pressure
• Regulates air pressure of the air line
• Self-relieving style units
• Available in T-handle or adjustment knob
• Adjustment knob features three position non-rising knob—push to
lock, pull to adjust, detach to make tamper resistant
• Reinforced diaphragm for repeated accuracy
Dry Air Systems
REFRIGERATED DRYERS
Air Systems
3-in-1 High Inlet Temperature Refrigerated Dryer
• Designed to handle inlet temperatures of 180°F versus 100°F on
a standard dryer system
• Eliminates the requirement of an aftercooler, separator and drain
• Handles compressed air DIRECTLY from the compressor receiver tank
• Removes moisture and filter contaminants and oil aerosols
• Vertical air hookups (in and out) and one electrical connection
• Dryers equipped with gauges
• External drain standard
Ascot
No.
117-35281
117-35282
117-35291
117-35292
117-35301
117-35302
117-35311
117-35312
117-35314
117-35322
117-35323
117-35324
117-35333
117-35334
117-35343
117-35344
117-35353
117-35354
117-35363
Model
No.
3528-1
3528-2
3529-1
3529-2
3530-1
3530-2
3531-1
3531-2
3531-4
3532-2
3532-3
3532-4
3533-3
3533-4
3534-3
3534-4
3535-3
3535-4
3536-3
Cap. 160°F
@ 100 Psig
21 SCFM
21 SCFM
30 SCFM
30 SCFM
50 SCFM
50 SCFM
70 SCFM
70 SCFM
70 SCFM
105 SCFM
105 SCFM
105 SCFM
135 SCFM
135 SCFM
220 SCFM
220 SCFM
300 SCFM
300 SCFM
400 SCFM
Cap. 160°F
@ 140 Psig
21.9 SCFM
21.9 SCFM
36.8 SCFM
36.8 SCFM
56 SCFM
56 SCFM
81 SCFM
81 SCFM
81 SCFM
130 SCFM
130 SCFM
130 SCFM
187 SCFM
187 SCFM
280 SCFM
280 SCFM
365 SCFM
365 SCFM
480 SCFM
Air Line Connect
In & Out
1” NPT
1” NPT
1” NPT
1” NPT
1” NPT
1” NPT
1” NPT
1” NPT
1” NPT
2” NPT
2” NPT
2” NPT
3” NPT
3” NPT
3” NPT
3” NPT
3” NPT
3” NPT
3” NPT
Sizing a 3-in-1 High Inlet Dryer
Follow the below steps to size your dryer:
1 Use the table that identifies your inlet temperature to your dryer.
2 In the chart select the inlet pressure that will be entering your dryer.
3 Determine SCFM.
RULE of THUMB CALCULATION
Rotary Screw Air Compressor
SCFM = Compressor HP x 4.5
Reciprocating Air Compressor
SCFM = Compressor HP x 4
4 Select the SCFM requirement for your dryer based on the SCFM
coming out the air compressor.
3528
3529
3530
3531
3532
3533
3534
3535
3536
26
100 PSIG 140 PSIG
21
30
50
70
105
135
220
300
400
21.9
36.8
56
81
130
187
280
365
480
Voltage
Phase
115V/1
208-230V/1
115V/1
208-230V/1
115V/1
208-230V/1
115V/1
208-230V/1
460V/3
208-230V/1
208-230V/3
460V/3
208-230V/3
460V/3
208-230V/3
460V/3
208-230V/3
460V/3
208-230V/3
175 PSIG
24
40
64
88
140
200
305
390
520
Dimensions (Inches)
Height Weight Length
27.5
20
30
27.5
20
30
27.5
20
30
27.5
20
30
27.5
20
30
27.5
20
30
31.5
27.5 34
31.5
27.5 34
31.5
27.5 34
42
29.5 40
42
29.5 40
42
29.5 40
49.5
38.5 44
49.5
38.5 44
49.5
38.5 44
49.5
38.5 44
63.5
38.5 52
63.5
38.5 52
63.5
38.5 52
Wt.
Lbs.
141
141
158
158
200
200
288
288
288
508
508
508
698
698
768
768
1113
1113
1190
KW
.40
.40
.51
.51
1.28
1.28
1.73
1.73
1.73
2.37
2.37
2.37
2.75
2.75
4.27
4.27
5.32
5.32
7.15
EXAMPLE: WHAT SIZE DRYER SHOULD BE USED?
Customer has a 20 HP reciprocating compressor. The inlet temperature to
the dryer is approximately 120° F. The pressure entering the dryer is 140 psi.
1. Identify the table that shows 120° F (in this example it would be table 3).
2. From the same table (table 3) select the inlet pressure of dryer. In this
example (140 psi).
3. Use Rule of Thumb Calculation to determine SCFM.
20 HP x 4 = 80 SCFM.
4. Locate 80 SCFM under 140 psi column. Follow across to dryer part
number.
ANSWER - Customer needs part number 3530.
TABLE 2 - 140° INLET
Model No.
Drain
Connect
3/8” OD
3/8” OD
3/8” OD
3/8” OD
3/8” OD
3/8” OD
3/8” OD
3/8” OD
3/8” OD
1/2” NPT
1/2” NPT
1/2” NPT
1/2” NPT
1/2” NPT
1/2” NPT
1/2” NPT
3/4” NPT
3/4” NPT
3/4” NPT
Model No.
100 PSIG 140 PSIG
175 PSIG
Model No.
100 PSIG 140 PSIG
175 PSIG
3528
3529
3530
3531
3532
3533
3534
3535
3536
24
44
70
85
148
228
332
420
555
29
53
83
102
178
272
396
502
665
3528
3529
3530
3531
3532
3533
3534
3535
3536
34
50
70
100
210
250
375
590
750
39
64
90
128
240
320
480
680
902
Air Systems
27
49
78
95
167
254
372
470
624
2007 Buyers Guide
37
58
81
115
229
290
435
640
860
Hose Reels
Low Pressure Hose Reels For
Air and Water
HOSE REELS
Ascot
No.
124-13500
124-15000
124-33500
125-35004
126-42500
126-43500
126-45000
126-52500
Mfg.
No.
P-LP-135
P-LP-150
P-LP-335
P-LP-350
P-LP-425
SH-N-435
SH-N-450
SH-N-525
Hose
ID
1/4”
1/4”
3/8”
3/8”
1/2”
1/2”
1/2”
3/4”
Hose
OD
1/2”
1/2”
21/32”
21/32”
27/32”
27/32”
27/32”
1-5/32”
Hose
Length
35’
50’
35’
50’
25’
35’
50’
25’
Hose
PSI
250
250
250
250
250
250
250
250
Safety Series Hose Reels
• Equipped with the EZ-COIL™ Rewind Safety System
• 80% Slower Retraction then that of conventional hose reels
• Controlled retraction reduces workplace
accidents
• EZ-COIL™ requires no electricity
• 0-1 ft./lbs. of impact at end of the recoil cycle
and 0-1 ft./lbs. “Whipping Radius”
• Auto-rewind for fast easy pay out and take up
• High-quality heavy duty steel construction
• Durable on-corrosive electrostatic powder
coat finish
• Adjustable hose stop
• Sturdy double supported solid steel 1” axle
• Multi-position arm guide adjusts for wall, ceiling or floor mounting
• Available in low, medium and high pressure
• “Safe-Replace” factory balanced cartridge style spring motor
• Multi-position locking ratchet secures hose at desired length
• Made in the U.S.A.
Ascot
No.
125-00325
125-00350
126-00425
126-00450
126-01450
Mfg.
No.
EZ-P-LP-325
EZ-P-LP-350
EZ--P-MP-425
EZ-MP-450
EZ-SH-450
Hose
ID
3/8”
3/8”
1/2”
1/2”
1/2”
Hose
Length
25’
50’
25’
50’
50’
Hose
PSI
300
300
2500
2500
250
Max.
Temp.
150° F
150° F
250° F
250° F
150° F
2007 Buyers Guide
Medium Pressure Hose Reels For
Air, Water & Oil
• High quality epoxy powder coated steel
construction
• Sturdy, double supported 1” solid steel axle
with 1” self-lubricated precision bearings
• 8-position locking ratchet secures hose at
desired length
• Multi-position guide arm adjusts to 10
different mounting positions
• 1/4” steel base plate and support post
• Self-retracting spring return reels
• Factory balanced cartridge-style spring motor
• Solid brass NPT swivel with stainless steel stud bolts to reel for
non-corrosive, long lasting strength and performance
Ascot
No.
125-32500
125-33502
125-35002
126-42501
126-43000
126-43501
126-45003
Mfg.
No.
P-MP-325
P-MP-335
MP-N-350
P-MP-425
P-MP-430
MP-N-435
MP-N-450
Hose
ID
3/8”
3/8”
3/8”
1/2”
1/2”
1/2”
1/2”
Hose
OD
5/8”
5/8”
5/8”
3/4”
3/4”
3/4”
3/4”
Hose
Length
25’
35’
50’
25’
30’
35’
50’
Hose
PSI
3000
3000
3000
2500
2500
2500
2500
High Pressure Hose Reels For Grease
• High quality steel construction
• Factory balanced cartridge-style spring
motor provide a safe, trouble-free
maintenance.
• 1/4” steel base plate and support post add
stiffness reducing vibration
• Sturdy, double supported 1” solid steel
axle with 1” self-lubricated precision bearings
• Detachable roller-guide harbors smooth
rollers that eliminate pinching and reduce
hose wear
• 10 different mounting positions
• 8-position locking ratchet
• Non-corrosive, stainless steel lock cam and
lock spring
Ascot
No.
124-12500
124-14000
124-15001
125-33000
125-33501
125-35003
Mfg.
No.
P-HP-125
HP-N-140
HP-N-150
P-HP-330
HP-N-335
HP-N-350
Air Systems
Hose
ID
1/4”
1/4”
1/4”
3/8”
3/8”
3/8”
Hose
OD
17/32”
17/32”
17/32”
43/64”
43/64”
43/64”
Hose
Length
25’
40’
50’
30’
35’
50’
Hose
PSI
5000
5000
5000
4000
4000
4000
27
Air Systems
• High quality epoxy powder coated
steel construction
• Sturdy 1” solid steel axle with 1”
self-lubricated precision bearings”
• Steel base plate and support post
add stiffness reducing vibration
• Multi-position guide arm adjusts to
10 different mounting positions
• 8-position locking ratchet secures
hose at desired length
• Self-retracting spring return reels
• Factory balanced cartridge-style spring motor provides safe main
tenance
• Solid brass NPT swivel with stainless steel stud bolts to reel
Hose Reels
HOSE REELS (continued)
Air Systems
B-Series Hose Reels
C-Series Low Pressure
Hose Reels
• For applications where shorter,
low volume hoses are used such
as auto-truck service garages
• For all air applications as well
as anti-freeze, motor oil, ATF and
grease
• Single set screw to access spring
casing
• Drive spring mechanism lubricated for life
• One piece combination latch, spring arbor, main
bearing and spool support for fewer moving parts
Ascot
No.
124-23500
124-20000
125-33500
125-30000
Mfg.
No.
LB-235
LB-200
LB-335
LB-300
Operating
Pressure
300 Psi
1000 Psi
300 Psi
1000 Psi
Hose
ID
1/4”
1/4”
3/8”
3/8”
Hose
Length
35
—
35
—
Ship
Weight
26 Lbs.
22 Lbs.
30 Lbs.
22 Lbs.
Unitract Series Hose Reels
Mfg.
No.
UTL250-OA
UTL350
UTL550
Operating
Pressure
300 Psi
300 Psi
300 Psi
Ascot
No.
125-35000
125-55000
Mfg.
No.
LC-350
LC-550
Operating
Pressure
300 Psi
300 Psi
Hose
ID
3/8”
1/2”
Hose
ID
1/4”
3/8”
1/2”
Hose
Length
50’ (twin)
50’
50’
Ship
Weight
44 Lbs.
41 Lbs.
45 Lbs.
Ascot
No.
126-54000
125-34000
Mfg.
No.
MC-540
HC-340
Operating
Pressure
2500 Psi
4000 Psi
Hose
ID
1/2”
3/8”
Lightweight, Durable, PVC Reels
•
•
•
•
•
• Lightweight, easy to handle
• Standard pivot bracket so the reel
can swing from side to side
• Made of corrosion proof, tough
polypropylene
• Design both protects the hose and allows
easy cleaning of both hose and reel
• Hose included
Compact Design
Substantial Support
Air/Water (OLP), Oil (OMP) or Grease (OHP)
All steel construction with engineered ribs/forms
Baked-on powder coat finish provides corrosion
resistance
28
Mfg.
No.
7650OLP
7670OLP
7850OLP
7650OMP
7850OMP
7450OHP
7650OHP
Hose
ID
3/8”
3/8”
1/2”
3/8”
1/2”
1/4”
3/8”
Hose
OD
.688
.688
.844
.690
.815
.590
.750
Ship
Weight
54 Lbs.
60 Lbs.
Hose
Length
40’
40’
Ship
Weight
56 Lbs.
62 Lbs.
• Medium pressure reel (MC-540) for
higher pressures for use with water
or heavier oils
• High pressure reel (HC-340) used
exclusively where grease is being
applied (i.e. off-road service, garage
lube system)
• Includes same features as C-Series Low
Pressure Hose Reel
Heavy Duty Industrial Reels
Ascot
No.
125-07650
125-07670
126-07850
125-07651
126-07851
124-07450
125-07652
Hose
Length
50’
50’
C-Series Medium & High Pressure
Hose Reels
• Weighs 10 lbs. less than standard
reels
• Unitized multi-functional hub arbor
• 8-position guide arm
• Minimal size envelope permits
installation where space is a factor
• Simple design incorporates fewer parts
• Single set screw to access latch area and
spring case
• Heavy gauge base with no welds
Ascot
No.
124-25014
125-35038
126-55012
• Reels ideally suited for plant
maintenance, service trucks or
other industrial functions
• Standard hose for air and water
• Single set screw to access spring
casing
• Drive spring mechanism lubricated for
life
• One piece combination latch, spring
arbor, main bearing and spool support for
fewer moving parts
• Brass swivel reduces corrosion potential
• Durable powder coated finish
Hose
PSI
300
300
300
2250
2000
5000
4000
Hose
Length
50’
70’
50’
50’
50’
50’
50’
Air Systems
Ascot
No.
125-03650
125-03665
126-03850
126-03851
126-03852
126-03853
Mfg.
No.
SGA3650OLP
SGA3665OLP
SGA3850OLP
SWA3850OLP
SHA3850OLP
SCA3850OLP
Hose
ID
3/8”
3/8”
1/2”
1/2”
1/2”
1/2”
2007 Buyers Guide
Hose
PSI
232
232
232
145
232
232
Hose Application
Length
50’ Air/Water
65’ Air/Water
50’ Air/Water
50’ Water
50’ Hot Water
50’ Chemical
Hose Reels
HOSE REELS (continued)
Cord Reels Open Style
Nitrogen Hose Reels
Ascot
No.
124-04500
125-06350
125-06500
126-08500
125-06501
126-08501
Mfg.
No.
RT450-OLP
RT635-OLP
RT650-OLP
RT850-OLP
RT650-OLPG
RT850-OLPG
Hose
ID
1/4”
3/8”
3/8”
1/2”
3/8”
1/2”
Hose
OD
.500
.640
.640
.781
.640
.781
Hose
Length
50’
35’
50’
50’
50’
50’
Hose
PSI
300
300
300
300
300
300
High Pressure Hose Reels
Mfg.
No.
4435OLP
4625OLP
5450OLP
5635OLP
5650OLP
A5850OLP
Hose
ID
1/4”
3/8”
1/4”
3/8”
3/8”
1/2”
Hose
OD
.500
.640
.500
.640
.640
.781
Hose
Length
35’
25’
50’
35’
50’
50’
Hose
PSI
300
300
300
300
300
300
• Flexible neoprene hose
• Rated at 300 psi
• Coupled 1/4” male NPT ball swivel at one end
and 1/4” female NPT fitting at the other end
• Used between quick coupler and air tool to protect coupler from
harmful impact
• Reduces kinking and twisting of air hose
Mfg. No.
596-6
597-6
598-2
599-2
597-2
Mfg.
No.
312-40351 L40351631
312-40501 L40501631
312-40352 L40351622
312-40502 L40501622
312-40353 L40351633
312-40503 L40501633
312-45453 L45451233
Wire Size No. of Cord
AWG
Wires Length Volts
Incandescent
16
3
35’
115
16
3
50’
115
Fluorescent
16
2
35’
115
16
2
50’
115
Single Outlet
16
3
35’
115
16
3
50’
115
12
3
45’
115
Max
Amps
13
13
0.3
0.3
13
13
25
• Full flow swivel and heavy guage
steel frame
• All-bolted unitized construction with no welds
to fatigue
• Hand Crank (CA) and 12VDC Electric Motor
(EA) driven
Whip Hose
Ascot No.
127-37240
127-37720
127-59820
127-59920
127-59720
Ascot
No.
General Industrial Air/Water
• Compact design allows reels to fit into
tight locations
• Corrosion resistant powder coated paint
• Exteded service life due to permanently
lubricated bearings and swivels
• Versatile applications include easy
mounts on wall, floor, ceiling or truck
• Air/Water hose included
Ascot
No.
124-04435
125-04625
125-05450
125-05635
125-05650
126-05850
• For indoor, non-weather-tight
applications only
• All models UL listed at 115 volt 60 hz
single phase; reels without cord suitable
for 220 volt
• Incandescent bulb 75 watt maximum
• Cord Included
Description
3/8” x 24” (1/4” x 1/4”) Lead-In
3/8” x 72” (1/4” x 1/4”) Lead-In
1/2” x 24” (1/2” x 3/8”) Lead-In
1/2” x 24” (1/2” x 1/2”) Lead-In
1/2” x 24” (1/2” x 1/4”) Lead-In
2007 Buyers Guide
Ascot
No.
126-21120
126-31120
126-31180
126-21121
126-31121
Mfg.
No.
CA32112L
CA33112L
CA33118L
EA32112L12D
EA33112L12D
Hose
ID
1/2”
3/4”
3/4”
1/2”
3/4”
Hose
OD
.845
1.188
1.188
.845
1.188
Hose
Length
200
100
175
200
100
Hose
PSI
1000
1000
1000
1000
1000
Nitro-Pro Nitrogen Reel
• EZ-Coil controlled retraction for
greater safety
• Special “Nitrogen green” proprietary “CPC”
powder-coated finish for long lasting durability
• Factory-matched lubricated containerized
spring motor for trouble free, enduring
performance
• 50’ of green 3/8” I.D. nitrogen hose &
adjustable hose stop
• Nitrogen quality seals in the full-flow brass
swivel inlet machined from solid
Ascot
Mfg.
No.
No.
127-05880 CP-0588
Air Systems
Hose
ID
3/8”
Hose
Length
50’
Hose
PSI
300
29
Air Systems
• Adjustable guide arm
locates to seven positions
• Oversized main shaft
increases support
• Long life drive spring
• Easy to mount due to slotted
mounting holes for safer and easier
installation
• Air/Water hose included
• Model RT650-OLPG specifically designed for dispensing nitrogen gas
Air Hose & Hose Reels
AIR HOSES (continued)
Hose Cutter
• Hand tool for straight, even,
clean cut on heater, air
conditioning and braided
rubber or plastic hose up to
1-1/8” diameter
Air Systems
SafeCoil Hoses
• Stretches and recoils
like a telephone cord
• Full 360° swivel at
each end
• Rated for working
pressures up to 300 psi
• Other sizes available, call for details
Ascot
No.
123-00412
123-00425
123-00450
123-00625
Mfg.
No.
4-12
4-25
4-50
6-25R
Hose
ID
1/4”
1/4”
1/4”
3/8”
Ascot No. Mfg. No.
137-10010 10010
137-10011 10011
Hose
Length
12’
25’
50’
25’
NPT
1/4”
1/4”
1/4”
3/8”
Std.
Pack
1
1
1
1
Heavy Duty Air Hose
• Smooth red rubber with NPT
fittings
• Lightweight and flexible
• Versatile and oil resistant
• Crimped ends
• Rated at 300 psi working
pressure
Ascot
No.
121-51225
121-51250
121-51210
121-51255
121-51450
121-55225
121-55250
121-55210
121-55525
121-55550
121-55510
121-51525
121-51550
121-51510
121-51500
Mfg.
No.
512-25
512-50
512-100
512-500
514-500
552-25
552-50A
552-100A
555-25*
555-50A*
555-100*
515-25
515-50
515-100
515-500
Hose
ID
1/4”
1/4”
1/4”
1/4”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
3/8”
1/2”
1/2”
1/2”
1/2”
NPT
1/4”
1/4”
1/4”
----1/4”
1/4”
1/4”
1/4”
1/4”
1/4”
1/2”
1/2”
1/2”
---
Hose
Length
25’
50’
100’
500’
500’
25’
50’
100’
25’
50’
100’
25’
50’
100’
500’
*Rubber hose with lock-on fittings.
*500ft. reels (bulk) do not have fittings.
30
Air Systems
Description
Hose Cutter
(2) High Grade Carbon Steel Replacement Blades
Premium Rubber Air Hose
• Smooth cover
• 300 PSI W.P. - 1,200 psi burst
pressure
• For heavy duty service
Ascot
No.
127-04425
127-04450
127-44100
127-06425
127-06450
127-64100
127-08425
127-08450
127-84100
Mfg.
No.
W44RJ25VSL
W44RJ50VSL
W44RJ100VSL
W64RJ25VSL
W64RJ50VSL
W64RJ100VSL
W84RJ25VSL
W84RJ50VSL
W84RJ100VSL
Hose
ID
1/4”
1/4”
1/4”
3/8”
3/8”
3/8”
1/2”
1/2”
1/2”
Hose
Length
25 ft.
50 ft.
100 ft.
25 ft.
50 ft.
100 ft.
25 ft.
50 ft.
100 ft.
NPT
1/4”
1/4”
1/4”
1/4”
1/4”
1/4”
1/2”
1/2”
1/2”
Weight
4 lbs.
8 lbs.
15 lbs.
5 lbs.
9 lbs.
17 lbs.
6 lbs.
12 lbs.
24 lbs.
Light Weight Premium PVC
Air Hose
• Smooth cover
• 300 PSI W.P. - 1,200 psi burst
pressure
• Applications: automotive, paint
body shop, construction general
industry
Ascot
No.
127-04625
127-04650
127-46100
127-06625
127-06650
127-66100
Mfg.
No.
W46DBLJ25VSL
W46DBLJ50VSL
W46DBL100VSL
W66TBLJ25VSL
W66TBLJ50VSL
W66TBLJ100VSL
Hose
ID
1/4”
1/4”
1/4”
3/8”
3/8”
3/8”
2007 Buyers Guide
Hose
Length
25 ft.
50 ft.
100 ft.
25 ft.
50 ft.
100 ft.
NPT
1/4”
1/4”
1/4”
1/4”
1/4”
1/4”
Weight
3 lbs.
6 lbs.
12 lbs.
4 lbs.
7 lbs.
13 lbs.
Air Hose
HOSE PRODUCTS, COUPLERS & PLUGS
Coiled Hoses
Hose Reels
• High-quality Polyurethane hose (Very
flexible and kink resistant)
• Hose guards at both ends (Long life)
• 360° Swivel at operator end
• Long straight section at operator end
• Pre-coated sealant on pipe threads
Mfg. No.
PUS64B
PUS64J
PUS68B
PUS68J
Connection
1/4" male NPT
1/4" male NPT
1/4" male NPT
1/4" male NPT
ID x Length
5/16" x 13 Ft
5/16" x 13 Ft
5/16" x 26 Ft
5/16" x 26 Ft
Ascot No.
124-01010
124-01015
Color
Blue
Yellow
Blue
Yellow
Mfg. No.
PUS64BIO
Ascot No.
128-72021
128-72022
128-72023
128-72024
128-72025
Description
Coiled Hose, Coupling, Blow Gun Assembly
Mfg. No.
27202OSH
27202SIL
27202PRE
27202ECR
27202MTL
Nozzle
Venturi
Silent
Standard
Air Shield
Metal
Regular Quick Couplings
Safety Quick Couplings
Plugs
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Easy push button release
Lightweight non-scratch composite body
Heavy-duty construction (long-lasting)
Easy, one-hand connection
Available in most common styles
Size
1/4
1/4
3/8
3/8
3/8
3/8
1/2
1/2
1/4
1/4
3/8
3/8
3/8
3/8
1/4
1/4
7.2
7.2
Body
Style
Ind'l Interchange
Ind'l Interchange
Ind'l Interchange
Ind'l Interchange
Ind'l Interchange
Ind'l Interchange
Ind'l Interchange
Ind'l Interchange
Truflate
Truflate
Truflate
Truflate
Truflate
Truflate
ARO
ARO
Highflow/European
Highflow/European
Connection
1/4" female NPT
1/4" male NPT
1/4" female NPT
3/8" female NPT
1/4" male NPT
3/8" male NPT
1/2" female NPT
1/2" male NPT
1/4" female NPT
1/4" male NPT
1/4" female NPT
3/8" female NPT
1/4" male NPT
3/8" male NPT
1/4" female NPT
1/4" male NPT
1/4" female NPT
1/4" male NPT
Safe two-stage release (No "hose-whip")
Easy push button release
Non-scratch composite body
Heavy-duty construction (long-lasting)
Easy, one-hand connection
Ascot
No.
131-61201
131-61251
131-81201
131-81202
131-81251
132-81252
133-11203
133-11353
131-11201
131-11251
131-18120
132-18121
131-18125
132-18122
131-21201
131-21251
131-71201
131-71251
ID x Length
3/8" x 33 Ft
3/8" x 50 Ft
• Non-restricted, full pressure
performance
• Sturdy, high-tech composite
material
• Light weight ergonomic design
• Variable air flow
128-72025
• 1/4” Female NPT
OSHA-compliant blowgun with booster nozzle
High-impact resistant push button coupler
Hardened steel male & female plugs
13 ft blue polyurethane kink-resistant
hose with hose guards & swivel end
Ascot No.
123-64000
Mfg. No.
Connection
DPF1010N 1/4" male NPT
DGF1015N 1/4" male NPT
Blow Guns
Coiled Hose, Coupling and Blow Gun Assembly
•
•
•
•
Heavy duty, epoxy-coated steel housing
Automatic hose locking system
Automatic winding feature
Protective Hose guard
Available with swivel mounting bracket
Regular
Couplng No.
IRC061201
IRC061251
IRC081201
IRC081202
IRC081251
IRC081252
ISG111203
ISG111353
URC061201
URC061251
URC081201
URC081202
URC081251
URC081252
ARC061201
ARC061251
ERC071201
ERC071251
2007 Buyers Guide
Ascot
No.
131-01201
131-01251
131-08120
132-08122
131-08125
132-08122
133-21023
—
131-10216
131-15216
131-10218
132-20218
131-15218
132-25218
131-20216
131-25216
131-10217
131-15217
Air Systems
128-72021 128-72023
Description
High-output, OSHA-Compliant
Quiet, OSHA-Compliant
Standard, Non-Scratch Nozzle
Unique Air Shield Nozzle
Durable Metal Nozzle
Available in most common styles
High Quality Steel
Carbon-nitrided (hardened) finish
Wide selection of connection
Safety
Coupling No.
ISC061201
ISC061251
ISC081201
ISC081202
ISC081251
ISC081252
ISG111203*
—
USC061201
USC061251
USC081201
USC081202
USC081251
USC081252
ASC061201
ASC061251
ESC071201
ESC071251
Ascot
No.
131-31201
131-31251
131-91201
132-91202
131-91251
132-91252
133-21123
133-21153
131-41201
131-41251
131-51201
132-51202
131-51251
132-51252
131-12070
131-12510
131-77120
131-77125
Plug
No.
IRP066201
IRP066251
IRP086201
IRP086202
IRP086251
IRP086252
IRP116203
IRP116253
URP066201
URP066251
URP086201
URP086202
URP086251
URP086252
ARP066201
ARP066251
ERP076201
ERP076251
31
Air Systems
Ascot No.
123-06401
123-06411
123-06801
123-06802
•
•
•
•
•
Air Line Couplers & Plugs
AIR LINE COUPLERS AND PLUGS
TYPE 1/4” Lincoln Long Nose
Air Systems
A
• Steel plated couplers with hardened steel balls and
stainless steel springs
• Plugs heat-treated to reduce wear on critical mating
surfaces
• Interchange with Lincoln “Long Nose Series” as well
as units produced by other manufacturers
Ascot
No.
Schrader
No.
131-61486 3527
131-61548 3528
Rema
Amflo
No.
No.
COUPLERS
2135
C27
2136
C28
131-61486
131-61548
Thread
NPT
Ascot
No.
Schrader
No.
Male
Female
1/4”
1/4”
131-61550
131-61551
3531
3532
Rema
Amflo
No.
No.
ADAPTER PLUGS
2235
CP27
2236
CP28
131-61550
Thread
NPT
Male
Female
1/4”
1/4”
TYPE 1/4” Aro Series
B
surfaces
• Interchange with Aro 210 series as well as units
produced by other manufacturers
• Maximum working pressure 300 psi.
Ascot
No.
Schrader
No.
131-61526
131-61527
131-08888
3526
3525
Dill 8888
Rema
Amflo
No.
No.
COUPLERS
2132
C38
2131
C37
Push- to-Connect
131-61526
131-61528
Thread
NPT
Ascot
No.
Schrader
No.
Female
Male
Female
1/4”
1/4”
1/4”
131-61529
131-61528
3530
3529
Rema
Amflo
No.
No.
ADAPTER PLUGS
2232
CP38
2231
CP37
Thread
NPT
Female
Male
1/4”
1/4”
TYPE 1/4” Automotive Standard (Tru-Flate)
C
Ascot
No.
surfaces
• Interchange with Tru-Flate 10 and 100 type series as
well as units produced by other manufacturers
Schrader
No.
131-61523 3504
131-61524 3503
32
Rema
Amflo
No.
No.
COUPLERS
2122
C2
2121
C1
131-61539
131-61524
131-61523
Thread
NPT
Ascot
No.
Female
Male
1/4”
1/4”
131-61539 3507
131-61538 3506
Air Systems
Schrader
No.
Rema
Amflo
No.
No.
ADAPTER PLUGS
2222
CP2
2221
CP1
2007 Buyers Guide
Thread
NPT
Female
Male
1/4”
1/4”
AIR LINE COUPLERS AND PLUGS
TYPE 1/4” Industrial Interchange Series
D
Ascot
No.
Schrader
No.
131-61573
131-61574
5142-12
5141-12
Rema
Amflo
No.
No.
COUPLERS
2140
C20
2139
C21
Thread
Female
Male
NPT
1/4”
1/4”
131-61573
Ascot
No.
131-61579
131-61578
131-61574
Schrader
No.
Rema
Amflo
No.
No.
ADAPTER PLUGS
5139-11
2240
CP20
5138-11
2239
CP21
131-61579
Thread
NPT
Female
Male
1/4”
1/4”
TYPE 1/2” Automotive Series
F
surfaces
Ascot
No.
Schrader
No.
133-61563
133-61564
3512
3511
Ascot No.
131-61471
Dill No.
D-17R
Rema
Amflo
No.
No.
COUPLERS
2156
C10
2155
C9
Description
Steel Coupler
w/ Sleeve Ring
Thread
Female
Male
Thread
Female
NPT
1/2”
1/2”
NPT
1/2”
131-61563
135-61471
Ascot
No.
Schrader
No.
133-61569
133-61568
133-61474
3514
3513
3537
Rema
Amflo
No.
No.
ADAPTER PLUGS
2256
CP10
2255
CP9
2257
CP9-03
131-61569
Thread
Female
Male
Male
NPT
1/2”
1/4”
3/8”
TYPE 3/8” Automotive Series
G
surfaces
131-61476
Ascot
No.
Schrader
No.
132-61476
132-61478
132-61553
132-61554
3521
NA
3516
3515
Rema
Amflo
No.
No.
COUPLERS
N/A
C8
N/A
C7
2162
C6
2161
C5
Thread
NPT
Female
Male
Female
Male
1/4”
1/4”
3/8”
3/8”
2007 Buyers Guide
131-61478
Ascot
No.
Schrader
No.
132-61481
132-61480
132-61559
132-61558
3520
3519
3518
3517
Air Systems
Rema
Amflo
No.
No.
ADAPTER PLUGS
N/A
CP8
N/A
CP7
2262
CP6
2261
CP5
131-61480
Thread
NPT
Female
Male
Female
Male
1/4”
1/4”
3/8”
3/8”
33
Air Systems
• Steel plated couplers with hardened steel balls
and stainless steel springs
• Plugs heat-treated to reduce wear on critical
mating surfaces
• Interchange with Aro, Foster, Milton as well as units
produced by other manufacturers
AIR LINE COUPLERS AND PLUGS (continued)
1/4” Retreader Series
Air Systems
134-61544
Ascot
No.
134-61544
134-61545
134-61487
134-61552
134-61543
Hansen Universal Auto-Flo
Couplings
134-61545
Description
Female 1/4” NPT Steel Plug
(.302-32 Std.)
Female 1/4” NPT Brass Coupler
With Sleeve
Female 1/4” NPT Steel Coupler
Female 1/4” NPT Plug
(.482 - 26-3/4”)
Male 1/4” NPT Plug
(.302-32 inner & outer thread)
134-61543
Schrader
No.
3508
Amflo
No.
CP12
N/A
C2RB
3505
3510
C2R
61-552
3533
CPI-302
Combo Coupler®
• One coupler fits 1/4”
Aro Style, 1/4” Automotive
Standard and 1/4” Industrial
Interchange plugs
135-61260
Ascot
No.
135-61240
135-61241
Description
1/4” Series, 1/4” NPT Female
1/4” Series, 1/4” NPT Male
Schrader
No.
—
—
Mfg.
No.
C60
C61
• High flow coupling designed for use
with compressed air
• First automatic universal
coupling designed to operate with
industrial, ARO 210 and Tru-Flate
Interchange plugs
Ascot No.
135-00023
135-00123
Description
Female 1/4” NPT Coupler
Male 1/4” NPT Coupler
Mfg. No.
B23AS-25F
B23AS-25M
Hi-Flo/HVLP Coupler
• Designed for air tools and
paint spray equipment
• Provides up to 50% more air
flow than conventional couplers
• Hi-Flo couplers/plugs for use
with sanders, grinders and high
air usage tools
• HVLP couplers for use with paint
spray guns
Ascot
No.
135-00900
135-00910
135-00980
135-00901
135-00911
Amflo
No.
C90
C91
C98
CP90
CP91
135-00910
135-00901
Description
1/4” FNPT Hi-Flo/HVLP Coupler-Brass
1/4” MNPT Hi-Flo/HVLP Coupler-Brass
1/4” FNPT Hi-Flo Coupler-Steel
1/4” FNPT Hi-Flo Plug-Steel
1/4” MNPT Hi-Flo Plug-Steel
Parker E-Z To Connect/Disconnect Coupling
•
•
•
•
E-Z-Mate is an exhaust type coupler designed to exhaust air pressure prior to disconnection
Valve sleeve acts as integral shut-off valve
Meets ISO 4414 requirements
Built-in sleeve-lok mechanically locks the valve sleeve
Female Couplers
Ascot No.
131-02514
131-02516
132-03716
132-03718
133-05018
133-05012
133-75112
133-75116
34
Part Number
EZ-251-4FP
EZ-251-6T
EZ-371-6T
EZ-371-8T
EZ-501-8T
EZ-501-12T
EZ-751-12T
EZ-751-16T
Body Size
1/4”
1/4”
3/8”
3/8”
1/2”
1/2”
3/4”
3/4”
Thread Size
1/4-18
3/4-18
3/8-18
1/2-14
1/2-14
3/4-14
3/4-14
1-11-1/2
Air Systems
Nipples
Ascot No.
131-17000
131-18000
133-17030
Part Number
CP17
CP18
CP1703
Body Size
1/2”
1/2”
1/2”
2007 Buyers Guide
NPT
1/2
1/2
3/8
Thread
Male
Male
Male
AIR LINE COUPLERS AND PLUGS (continued)
LINCOLN
ARO
Air Systems
TRUFLATE
MILTON
DIAMOND-U
IDENTIFICATION CHART
Schrader
Amflo
Camel
Dill
Milton
1/4” Tru-Flate Automotive Type
3503
3504C-D
3504
3505
3506
3507
3508
3510
3533
C1
—
C2
C2R
CP1
CP2
CP12
CP14
CP1-302
61-524
—
61-523
61-487
61-538
61-539
—
61-552
61-544
D-12
—
D-13
D-13R
D-2C
D-3C
D-6C
D-7CR
D-5C
786
—
785
787
783
784
779
781
—
1/4” ”ARO” Speed Series Type
3526
3529
3530
C38
CP37
CP38
61-526
61-528
61-529
8888
8891
8889
775
777
778
1/4” Industrial Interchange Type
5138-11
5138-12
5139-11
5139-12
5140-12
5141-12
5142-12
5142C-D
5223-11
5263-11
5263-12
CP21
—
CP20
—
C21-103
C21
C20
—
CP21-42
CP21-103
C20-23
61-578
—
61-579
—
—
61-574
61-573
61-572
—
61-535
—
110
—
109
—
—
103
102
—
—
115
—
727
—
728
—
719
716
715
711
736
733
718
2007 Buyers Guide
Schrader
Amflo
Camel
Dill
Milton
1/4” Lincoln Long Stem Type
3528
3531
3532
C28
CP27
CP28
3515
3516
3517
3518
3519
3520
3521
C5
C6
CP5
CP6
CP7
CP8
C8
61-548
61-550
61-551
123
126
125
790
791
792
3/8” Tru-Flate Type
61-554
61-553
61-558
61-559
61-480
61-481
61-476
—
D-15
D-2E
D-3E
D-0E
—
D-15C
1806
1805
1807
1808
1809
1810
1803
3/8” Industrial Interchange Type
3541
3542
3543
C26
CP25
CP26
3511
3512
—
3513
3514
3537
C9
C10
C10R
CP9
CP10
CP9-03
61-482
61-484
61-485
117
122
121
1835
1837
1838
1/2” Tru-Flate Type
Air Systems
61-564
61-563
61-471
61-568
61-569
61-474
D-16
D-17
D-17R
D-2F
D-3F
D-0F
1816
1815
—
1817
1818
1819
35
Air Line Accessories
AIR TANK, BLOW GUN & HOSE ADAPTERS
Air Systems
Air Tanks
• Patented built-in pressure
by-pass valve
• Easy to read pressure gauge
• Heavy-gauge steel
construction
• Maximum pressure up to
125 psi
• Portable design with easy
carrying handle
• 4 foot rubber hose
• Durable valve chuck
Ascot No.
129-01010
Mfg. No.
W-1010A
Brass In-Line Swivels
• Simple design is excellent to stop hoses
from kinking or for use in pneumatic
equipment applications
Ascot No.
136-02344
136-02366
Description
10-Gallon Air Tank
Shipping Wt.
26 Lbs.
• Rugged construction with
hang hook
• Accepts a full range of accessories
Ascot No.
128-20000
Ascot
No.
136-00403
136-00398
136-00401
136-00604
136-00406
136-00606
136-00806
136-00408
136-00608
136-00808
136-00813
136-00812
136-00818
• Excellent for running several air lines
from a common supply hose
NPT Thread
1/4”
3/8”
Solid Brass Female Tees
• Use to run two lines from a
common feed
Ascot No.
136-01344
136-01366
Mfg. No.
344T
366T
NPT Thread
1/4”
3/8”
Brass Angle Swivel
• Simple design is excellent to stop
hoses from kinking or for use in
pneumatic equipment applications
Ascot No.
136-34490
36
Mfg. No.
344R90
Mfg. No.
344U
NPT Thread
1/4” NPTF x 1/4” NPTM
• Select fitting to match hose ID
• Fittings must be secured to hose
with either a hose clamp or crimped-on
ferrule
Mfg. No.
200K
Mfg. No.
344X
366X
• Features a full 360° swivel to keep
hose from twisting when using air
operated tools and while paint spraying
Standard Male Hose
Barb Fittings
Solid Brass Female Crosses
Ascot No.
136-00344
136-00366
NPT Thread
1/4” Male/Female NPT
3/8” Male/Female NPT
Uniswivel
Ascot No.
136-03344
Standard Blow Gun
Mfg. No.
344R
366R
NPT Thread
1/4” Male/Female Swivel
Air Systems
NPT
Thread
1/4”
3/8” -24”
1/4”
3/8”
1/4”
3/8”
1/2”
1/4”
3/8”
1/2”
3/4”
1/2”
1”
Hose
ID
3/16”
1/4”
1/4’
1/4”
3/8”
3/8”
3/8”
1/2”
1/2”
1/2”
1/2”
3/4”
1”
Mfg.
No.
403
398
401
604
406
606
806
408
608
808
813
812
818
Call Us For Our Complete
Offering Of Hose Fittings
And Adapters.
2007 Buyers Guide
Air Line Accessories
AIR TANK, BLOW GUN & HOSE ADAPTERS
Male Pipe Couplings
• Solid brass NPT
REUSABLE HOSE REPAIR FITTINGS
Male Pipe Thread
Ascot No.
137-00418
137-00439
137-00419
137-00420
137-00520
137-00620
137-00621
137-00623
137-00624
137-00625
137-00828
Mfg. No.
418
439
419
420
520
620
621
623
624
625
828
Hose OD
1/2”
9/16”
19/32”
5/8”
5/8”
5/8”
21/32”
23/32”
21/32”
23/32”
7/8”
Hose ID
1/4”
1/4”
1/4”
1/4”
5/16”
3/8”
3/8”
3/8”
3/8”
3/8”
1/2”
NPT
1/4”
1/4”
1/4”
1/4”
1/4”
1/4”
1/4”
1/4”
3/8”
3/8”
1/2”
Female Pipe Thread
Ascot No.
137-00324
137-00344
137-00346
137-00366
137-00388
137-00389
Mfg. No.
324
344
346
366
388
389
Male NPT
1/8”
1/4”
3/8”
3/8”
1/2”
3/4”
Male NPT
1/4”
1/4”
1/4”
3/8”
1/2”
3/4”
Male NPT
1/4”
1/8”
3/8”
1/2”
1/4”
1/2”
3/4”
Female NPT
1/8”
1/4”
1/4”
1/4”
3/8”
3/8”
1/2”
Air Systems
• Makes air tight connection without using hose clamps
• Must closely match hose OD (outer diameter) and ID (inner
diameter) accurately before ordering
• Minimum order is box of ten
Bushings And Adapters
• Solid brass
Ascot No.
137-01324
137-01342
137-01346
137-01348
137-01364
137-01368
137-01389
Mfg. No.
324F
342F
346F
348F
364F
368F
389F
Pipe Coupling Female NPT
• Solid brass
Ascot No.
137-01418
137-01439
137-01520
137-01621
137-01623
137-01624
Mfg. No.
418F
439F
520F
621F
623F
624F
Hose OD
1/2”
9/16”
5/8”
21/32”
23/32”
21/32”
Hose ID
1/4”
1/4”
5/16”
3/8”
3/8”
3/8”
Mfg. No.
520S
621S
623S
Hose OD
5/8”
21/32”
23/32”
Hose ID
5/16”
3/8”
3/8”
NPT
1/4”
1/4”
1/4”
1/4”
1/4”
3/8”
Hose Splicers
Ascot No.
137-11520
137-11621
137-11623
2007 Buyers Guide
Ascot No.
137-01344
Mfg. No.
344F
Male NPT
1/4” x 1/4”
Standard Hose Crimper
• Provides production capability
and “big tool” crimping advan
tages at a much lower cost
• Heavy duty ductile iron casting and
hardened steel dies for long service life and
positive crimping
• With five dies for crimping 1/4” single braid to 3/8”
double braided hose
Ascot No.
137-08550
137-08551
Mfg. No.
855
855A
Air Systems
Description
Standard Hose Crimper
Same Tool As Crimper Above Except
Largest Die Is Replaced By 7/16” For
Crimping 3/16” Hose
37
Hose Fittings
HOSE ADAPTERS
Brass Ferrules
• For use with hose barb fittings
• Use with hose crimper (Ascot No. 137-08550)
• 50 per box
Hose Crimper Replacement Dies
Air Systems
• Replacement dies for Hose Crimper (Ascot No. 137-08550 and
Ascot No. 137-08851)
Ascot No.
137-08561
137-08532
137-08563
137-08564
137-08565
137-08567
137-08568
137-08569
137-85610
Amflo No.
856-1
856-2
856-3
856-4
856-5
856-7
856-8
856-9
856-10
Die Size
5/8”
37/64”
17/32”
31/64”
11/16”
7/16”
3/4”
13/16”
3/8”
Hose Crimper Kit
• Kit is complete
with standard
crimper ferrules,
hose barbs,
splicer & directions needed to make up hoses in the field
• Organized in a plastic tote
• Contents: Hose Barbs: 10; Hose Splicers: 10; Ferrules: 20;
Standard Crimper: 1
Ascot No.
137-00855
Ascot No.
137-73215
137-73225
137-73235
137-73255
137-73265
137-73275
137-73285
137-73295
137-73305
137-73315
137-73325
137-73335
137-73345
137-73355
137-39525
137-50291
137-72421
Amflo No.
7321-50
7322-50
7323-50
7325-50
7326-50
7327-50
7328-50
7329-50
7330-50
7331-50
7332-50
7333-50
7334-50
7335-50
3952-50
5029A-50
7242A-50
Ferrule I.D.
.478”
.500”
.527”
.562”
.593”
.625”
.656”
.687”
.718”
.750”
.781”
.812”
.825”
.850”
.875”
.900”
.937”
Oetiker 2-Ear Clamp
Service Kit
• Service kit contains the following
sizes: (15) 5/16”; (15) 7/16”; (15) 1/2”; (15) 9/16”; (12) 5/8”; (12)
3/4”; (12) 7/8”; (12) 15/16”; (12) 1”; and (1) pair straight jaw pincers
Mfg. No.
855K
Oetiker 2-Ear Clamps
• Especially suited for industrial or heavy
vibrating equipment
• Medium pressure clamp that is
used for maintenance and OEM applications
• Rubber hose, plastic tubing, coaxial
and electrical cable, rope are easily clamped
• For air, fluid, gas, steam line
Ascot
No.
316-00507
316-00709
316-00911
316-01113
316-01315
316-01518
316-01720
316-01922
316-02023
316-02225
316-02327
38
Mfg.
No.
507
709
911
1113
1315
1518
1720
1922
2023
2225
2327
Nominal
Size
1/4”
5/16”
7/16”
1/2”
9/16”
5/8”
3/4”
13/16”
7/8”
15/16”
1”
Ascot No.
316-91098
Inches
Closed-Open
.197-276”
.276-.354”
.355-.433”
.433-.512”
.512-.591”
.591-.708”
.669-.787”
.748-.866”
.787-.905”
.866-.984”
.905-1.063”
Air Systems
MM
Closed Open
5-7 mm
7-9 mm
9-11 mm
11-13 mm
13-15 mm
15-18 mm
17-20 mm
19-22 mm
20-23 mm
22-25 mm
23-27 mm
Mfg. No.
SK1098
Inner
Inches
.236”
.276”
.276”
.276”
.295”
.315’
.335”
.354”
.354
.394”
.394”
2007 Buyers Guide
Width
of Ear
6.0 mm
7.0 mm
7.0 mm
7.0 mm
7.5 mm
8.0 mm
8.5 mm
9.0 mm
9.0 mm
10.0 mm
10.0 mm

Air Systems - Tuffy Manufacturing

Transcription

Similar documents

GRINDING - Stellar Industrial Sales Ltd.