Wictec INTERNATIONAL_Mise en page 1

Transcription

Wictec INTERNATIONAL_Mise en page 1
Wictec INTERNATIONAL_Mise en page 1 30/11/12 11:01 Page1
WICTEC
Aluminium façade solutions
Wictec INTERNATIONAL_Mise en page 1 30/11/12 11:01 Page2
WICTEC aluminium
façade solutions
1I
WICTEC solutions are used to create large vertical façades:
grid, vertical and horizontal emphasis, structural sealant glazing,
beaded glazing, aluminium/wood plant-on systems, unitised
façades, high energy-performance façades, high-security
façades, and roof glazing, prisms, domes and pyramids.
the exterior. A wide choice of cap profiles and transoms can
be used to customise façades.
With its patented design, the WICTEC range offers the option
of flat or facetted construction. The vertical façade is mullion
drained, and the roof cascade-drained, to remove water to
With three levels of drainage, complex constructions integrating
vertical façades and roof glazing are possible.
The WICTEC systems are compatible with WICSOLAIRE
brise-soleil.
Wictec INTERNATIONAL_Mise en page 1 30/11/12 11:01 Page3
2I
Aluminium grid curtain wall façades
4-7
External appearance design
8-9
Vertical and horizontal emphasis
curtain wall façades
10-11
Structural sealant glazing (SSG) façades
12-13
Beaded glazing (BG) façades
14-15
High energy performance façades:
solutions for low-energy buildings
16-19
High-security façades:
burglar resistant and bullet-proof
20-21
Unitised façades
22-23
Mechanical structural glazing façades
24-25
Pyramids, domes and glass roofs
26-27
Mullions, transoms and cap profiles
28-29
Technology for Ideas
30-31
1 I Contemporary Arts Center
Architects: Mongiello and Plisson - Photo: Airshoot
2 I Auréalys
Architect: AABD Bruno Dumétier - Photo: Gilles Aymard
3 I Ferrari Restaurant
Architects: MDN Marco Visconti & Partners - Photo: Wicona Rights
4 I Larnaca airport
Architects: Pascall, Watson & J.A. Philippou - Photo: Wicona Rights
3I
4I
Wictec INTERNATIONAL_Mise en page 1 30/11/12 11:01 Page4
Aluminium grid
curtain wall façades
1I
Wictec INTERNATIONAL_Mise en page 1 30/11/12 11:01 Page5
Grid
WICTEC 50
Grid curtain wall
Grid curtain wall and roof glazing, on 50 mm-wide frame, depth
of mullions/transoms determined by required inertia values
• Mullion inertia reaches 3 000 cm4 and 11 000 cm4 (reinforced)
• Glazing infill: from 3 to 51 mm
• Architectural façades: variable angle up to 90° due to rotating gaskets
at mullions (WICONA patent) with an infill capacity of 3 to 33 mm.
• Aluminium/wood plant-on façade
• Vent and door integration • Brise-soleil integration
• Roof glazing and roof vents
• Choice of cap profiles and mullions with a variety of shapes
and sizes
•
Horizontal section
Performance
• Maximum infill weight per transom: 120 kg with connectors or 400 kg
with transom block
• Grid thermal performances with integrated concealed vent
- Ucw 100% glazed = 1.2 W/m2.K with glazing Ug = 0.6 W/m2.K
- Ucw 50% glazed = 1.0 W/m2.K with glazing Ug = 0.6 W/m2.K
and Up = 0.35 W/m2.K
• R
A,tr = 42 dB with 40 mm glazing on fixed light and vent
0 to 90° faceted
1 I Vichy Val d’Allier, Vichy
Architect: Daniel Rubin - Photo: Gilles Aymard
2 I Off Road Verlag, Ottobrunn
Architect: Buro Gruber und Simon - Photo: Wicona Rights
Horizontal section
2I
Applications
Grid
Fixed light
Vent
integration
Faceted
curtain wall
4
5
Wictec INTERNATIONAL_Mise en page 1 30/11/12 11:01 Page6
WICTEC 50
1I
Vent integration
• Grid façade
• Integration of S.S.G. open-out windows with concealed sashes
and WICLINE series windows
• Integration of concealed tilt and turn vent: identical thermal performance of fixed and opening section
• Integration of WICSTYLE series doors
• Integration of brise-soleil
- WICSOLAIRE fixed brise-soleil
- Adjustable brise-soleil, guided by slide integration into the cap
profile
Open-out concealed vent - grid
Horizontal section
Open-out concealed vent - grid
Vertical section
Wictec INTERNATIONAL_Mise en page 1 30/11/12 11:01 Page7
2I
Brise-soleil integration (BSO)
3I
BSO Integration
6
7
Horizontal section
1 I EON Bayern, Munich
Architect: HJ Horstmann - Photo: Wicona Rights
2 I Wicona rights
3 I Wicona rights
Wictec INTERNATIONAL_Mise en page 1 30/11/12 11:01 Page8
External appearance design
Options for unique designs
• Industrial design: mullions, transoms and caps, T or I shape
• S.S.G. appearance: integrated pressure plate cap
• B.G. appearance: integrated pressure plate cap with infill gasket
WICTEC 50
Industrial design
U-shaped integrated pressure plate cap/industrial mullion node horizontal section
Wictec INTERNATIONAL_Mise en page 1 30/11/12 11:01 Page9
Design
S.S.G. appearance
B.G. appearance
8
9
Horizontal section
Horizontal section
Integrated pressure plate cap - S.S.G. appearance
Integrated pressure plate cap - B.G. appearance
1 I WALZ, Ulm
Metal builder: Dobel Metalbau – Photo: Wicona Rights
2 I CPAM, Annecy
Architect: Van de Wyngaert – Photo: Gilles Aymard
1I
2I
Wictec INTERNATIONAL_Mise en page 1 30/11/12 11:01 Page10
Vertical and horizontal
emphasis curtain wall
façades
Wictec INTERNATIONAL_Mise en page 1 30/11/12 11:01 Page11
Horizontal emphasis
Vertical and horizontal emphasis
Horizontal emphasis
curtain wall
WICTEC 50
Vertical or horizontal emphasis curtain wall, on 50 mm-wide frame,
depth of mullions/transoms determined by required inertia values
• Variable appearance: the capping on the transoms and the mullions
is used to emphasise the façade’s horizontal or vertical lines
• Glazing infill: 26 and 32 mm for horizontal line and 30 mm for
vertical line
•
Appearance
Choice of cap profiles with a variety of sizes and shapes:
- aluminum and stainless steel rectangular
- U shape, industrial
- aerofoil shape or T shape
• Mullion design: rectangular and T or I shaped (“industrial” design)
S.S.G. open-out window vertical section
•
Vent integration
S.S.G. concealed open-out for horizontal line
Vertical emphasis
10
11
•
Performance
Maximum infill weight per transom: 120 kg with connectors or
400 kg with transom block for horizontal emphasis
• Horizontal emphasis thermal performances
- Ucw 100 % glazed = 1.6 W/m2.K with glazing Ug = 1.3 W/m2.K
- Ucw 50 % glazed = 1.2 W/m2.K with glazing Ug = 1.3 W/m2.K and
Up = 0.35 W/m2.K
Vertical emphasis
curtain wall
•
AVA, Clermont-Ferrand
Architect: André Jalicon - Photo: JL. Sarda
Applications
Horizontal emphasis
Fixed light
Vertical emphasis
Vent
integration
Fixed light
Fixed light horizontal section
Wictec INTERNATIONAL_Mise en page 1 30/11/12 11:01 Page12
S.S.G. curtain wall façades
1I
Wictec INTERNATIONAL_Mise en page 1 30/11/12 11:01 Page13
S.S.G.
S.S.G. top-hung window
WICTEC 50
Structural sealant glazing (S.S.G.) curtain walling, on 50 mmwide frame, depth of mullions/transoms determined by required
inertia values
• Glazing infill:
- from 28 to 34 mm and from 35 to 37 for fixed frames
- from 26 to 32 mm for top-hung window
• 40 mm-wide black anodised aluminium security pieces are provided
• Product subject to Technical Evaluation No. 2/02-981
•
Appearance
Glass bonded with an anodised aluminium strip
• 21 mm infill gasket
• Mullion design:
- rectangular
- T shape
- I shape (“industrial” design)
•
12
13
Horizontal section
Vent integration
Top-hung window
•
1 I MMA Headquarters, Le Mans
Architects: Boissesson, Dumas, Vilmorin et Associés - Photo: J. Pierre Lagarde
2 I Swiss Life, Marseille
Architects: Daniel Habasque - Photo: Serge Demailly
Vertical section
Applications
Fixed light
Vent
integration
2I
Wictec INTERNATIONAL_Mise en page 1 30/11/12 11:01 Page14
B.G. curtain wall façades
Wictec INTERNATIONAL_Mise en page 1 30/11/12 11:01 Page15
B.G.
Fixed light
WICTEC 50
Beaded glazing (B.G.) curtain walling, on 50mm-wide frame, depth
of mullions/transoms determined by required inertia values
• Glazing infill from 12 to 31 mm
•
Appearance
The infill volumes of top-hung vents or fixed lights are bordered
by an aluminium glazing bead with a sight line width of 28 mm.
• 21 mm infill gasket
• Mullion design:
- rectangular
- T shape
- I shape (“industrial” design)
•
Vertical section
Top-hung window integration
14
Vent integration
Top-hung window
15
•
Applications
Fixed light
Vent
integration
Horizontal section
Sanofi Laboratory, Toulouse
Architects: Larrouy et Sicre - Photo: Xavier Boymond
Vertical section
Wictec INTERNATIONAL_Mise en page 1 30/11/12 11:01 Page16
High energy-performance
façades: solutions for
low-energy buildings
Wictec INTERNATIONAL_Mise en page 1 30/11/12 11:02 Page17
High insulation
WICTEC 50HI
WICTEC 50 HI is a WICTEC 50 curtain wall variant used to improve
the thermal insulation of a façade and to meet low-energy building
requirements
• High thermal insulation spacer
• Glazing infill from 21 to 51 mm
• Burglar resistance classification WK 2 (NF EN 1627) with reinforced
pressure plate
•
Appearance
Choice of cap profiles and mullions with a variety of shapes
and sizes:
- rectangular in aluminium and stainless steel
- aerofoil or T shape, U shape, "industrial" design
- cap profile with guide to integrate movable brise-soleil
• Mullion design: rectangular, T or I shape, “industrial” design
•
Fixed light
16
17
Vent integration
Top-hung window
• WICLINE window integration
•
Performance
Maximum infill weight per transom: 120 kg with connectors or 400 kg
with transom block for horizontal emphasis
• Thermal performance
- Ucw 100 % glazed = 0.9 W/m2.K with glazing Ug = 0.6 W/m2.K
- Ucw 50 % glazed = 0.9 W/m2.K with glazing Ug = 0.6 W/m2.K
and Up = 0.54 W/m2.K
•
Kreissparkasse
Architects: Auer Weber and assozierte - Photo: Wicona rights
Applications
Fixed light
Vent
integration
Horizontal section
Wictec INTERNATIONAL_Mise en page 1 30/11/12 11:02 Page18
WICTEC 50CS
Façade with non-S.S.G. concealed vent
• Identical thermal performance between fixed and opening sections
• Design: non-S.S.G. concealed vent
• Glazing infill: 32 and 42 mm for double and triple glazing
WICTEC 50CS
WICTEC 50A
Performance
Thermal performance
- Ucw 100 % glazed = 1.2 W/m2.K with Ug = 0.6 W/m2.K
- Ucw 50 % glazed = 1.0 W/m2.K with Ug = 0.6 W/m2.K and
Up = 0.35 W/m2.K
•
Turn and Tilt concealed vent
Horizontal section
Wictec INTERNATIONAL_Mise en page 1 30/11/12 11:02 Page19
Aluminium/wood plant on
WICTEC 50A
Aluminium/wood plant on façade
• The WICTEC 50 grid curtain wall system is used to create composite
aluminium/timber façades, over 50 mm wide, with glazing infills of
up to 51 mm permitted
• Two mullion/transom solutions are available:
- a mullion profile and a transom profile allowing clip fixing to the
wood frame
- a mullion/transom profile allowing screw fixing to the wood frame
• The aluminium/wood façade allies the advantages of aluminium
and of wood to provide effective thermal insulation. This solution meets
low-energy building requirements - Ucw 100% glazed < 1.0 W/m2.K.
18
19
Horizontal section
Vertical section
Mont-Cenis Academy, Herne
Architects: Jourda and Parraudin - Photo: Conné van d’Grachten
Wictec INTERNATIONAL_Mise en page 1 30/11/12 11:02 Page20
High-security façades:
burglar resistant and
bullet-proof
1I
Wictec INTERNATIONAL_Mise en page 1 30/11/12 11:02 Page21
2I
Protection
WICTEC 50 Burglar resistant
WICTEC 50 Bullet-resistant
WICTEC 50 Burglar resistant
• Based on the WICTEC 50 curtain wall principle, a burglar resistant
solution uses a special pressure plate and additional reinforcements
on the mullions and transoms
• Glazing infill up to 51 mm
WICTEC 50 Bullet-proof
• Based on the WICTEC 50 curtain wall, a bullet-proof solution
uses additional reinforcements on the mullions and transoms
• Glazing infill up to 57 mm
Appearance
• Rectangular mullions and cap profiles
Performance
• Maximum infill weight per transom: 120 kg with connectors or 400 kg
with transom block for horizontal emphasis
• Burglar resistant classification RC 2, RC 2N, and RC 3, DIN EN 1627
(2011)
Fixed light
Appearance
• Rectangular mullions and cap profiles
Performance
Maximum infill weight per transom: 120 kg with connectors or 400 kg
with transom block for horizontal emphasis
• Bullet-proof classification FB4, NF EN 1522
•
20
21
Fixed light
FB4
1 I Photo: Wicona Rights
2 I Photo: Wicona Rights
Horizontal section
Horizontal section
Applications
Burglar resistant
Applications
Bullet-proof
Fixed light
Fixed light
Wictec INTERNATIONAL_Mise en page 1 30/11/12 11:02 Page22
Unitised façade
The unitised system is fully manufactured, glazed and sealed in
factory controlled conditions before the complete units are moved
to site for fast and easy installation onto pre-prepared fixings. A
façade area greater than 350m2 can be installed per team per day.
Wictec INTERNATIONAL_Mise en page 1 30/11/12 11:02 Page23
Unitised
Applications
WICTEC 50EL
Fixed light
Solutions requiring less installation time on site
Units prefabricated and glazed in the workshop
• Hook-type anchoring of units using fixing lugs on, under or in front
of slab
• Slim lines and optimisation of the glass surface area due to lighter
aluminium weights (crossbars and transoms with a 65 mm inner
sight line)
• Glazing infills from 22 to 44 mm
• Maximum sizes: L 3 000 x H 3 500 mm with intermediate transoms
and mullions or 200 kg / frame
• Expansion adjustment: 5 mm horizontally and vertically
•
•
Appearance
Straight cap profiles
• Assemblies: 65 mm inner sight line on frame junctions and 50 mm
on intermediate mullions/transoms
•
65 mm vertical joint
Vent integration
Vent integration
• WICLINE top-hung window and tilt
& turn window
• WICSTYLE door
• Natural ventilation vents
Performance
Maximum sizes
- Unit with mullion and intermediate
transom: 3 000 x 3 500 m or 200 kg
/ frame
• Thermal performance
- Ucw 100 % glazed = 1.0 W/m2.K
with glazing Ug = 0.6 W/m2.K
- Ucw 50 % glazed = 0.9 W/m2.K
with glazing Ug = 0.6 W/m2.K and
Up = 0.35 W/m2.K
•
50 mm intermediate mullion
22
23
Opening vent
65 mm vertical joint
Unit maximum length = 3 meters
with intermediate mullion
Horizontal section
Tornado Tower
Architect: Robinson Pourroy - Photo: Wicona rights
Horizontal section
Horizontal section
Wictec INTERNATIONAL_Mise en page 1 30/11/12 11:02 Page24
Mechanical structural
glazing façades
Fully glazed façades have a firm place in contemporary
architecture and create impressive building elevations.
Using WICONA systems, fine external structures with
narrow joints can be created.
Opening elements and glazed spandrel panels can
be incorporated. Based on an innovative mechanical
fixing, WICTEC 50SG opens up a new, simpler option
for the construction of flush glass façades.
1I
Designed as a traditional stick system, the glazing
unit is retained by a 'toggle' within the infill channel.
Although its appearance is identical to that of a
traditional S.S.G. façade, this technology is faster,
simpler and more economical to realise.
Wictec INTERNATIONAL_Mise en page 1 30/11/12 11:02 Page25
Structural glazing
WICTEC 50SG
Splendid views
• Outstanding appearance with extremely slim silicone joints
• Basic structure is the WICTEC 50 façade, with easy glazing on site,
without the requirement for special tools
• Simple and straightforward installation thanks to a special toggle
fastener
• Standard glass spacers can be used
2I
24
25
Horizontal section
Vertical section
1 I Photo: Wicona Rights
2 I Al Attiya Tower, Qatar
Architect: Arab Engineering Bureau - Photo: Wicona Rights
Wictec INTERNATIONAL_Mise en page 1 30/11/12 11:02 Page26
Aluminium pyramids,
domes and roof glazing
1I
Wictec INTERNATIONAL_Mise en page 1 30/11/12 11:02 Page27
Glass roofs
Glass roofs
WICTEC 50
Due to its element drainage and system sealing principles,
WICTEC 50 offers numerous different glass roof, dome and pyramid
designs
• Glazing infills from 3 to 51 mm
• Roof vent glazing infill from 26 to 32 mm
•
Upper transition
point vertical
section
1 I Vichy-Val d’Allier
Architect: Daniel Rubin - Photo: Gilles Aymard
2 I C.C. Quartier Libre, Pau
Architects: Wilmotte et associés - Photo: Wicona rights
3 I Stadtbibliothek, Ulm
Architect: Gotfried Bohm - Photo: Wicona rights
26
27
Vertical section
on transom
Lower transition point
vertical section
2I
3I
Applications
Sloped glazing
Roof frame connectors
Inward angle and hip
Outward angle and valley
Prism
Pyramid
Dome
Wictec INTERNATIONAL_Mise en page 1 30/11/12 11:02 Page28
Mullions, transoms
and cap profiles
Rectangular mullions and transoms
Max l =
2000 cm4
Max l =
3000 cm4
Depth: 32 to 206 mm
Depth: 226 mm
Max l with steel
reinforcement
piece =
11000 cm4
Depth: 106 to 206 mm
Depth: 261 mm
Depth: 66 to 206 mm
Max l =
1460 cm4
Max l =
733 cm4
Depth: 169 to 276 mm
Max l =
700 cm4
Max l with
steel
reinforcement
piece =
5538 cm4
Max l =
500 cm4
Transom
“Atrium”
mullion
Reinforced
mullions
Standard
variable angle
mullions
Reinforced
variable angle
mullion
Depth: 86 to 126 mm
Depth: 106 to 166 mm
Standard
mullions
Transom
Expansion
mullions
Half-mullions
Integration of "concealed"
Turn and Tilt
Corner
post
Steel and wood structure clip-on sections
Depth: 106 to 146 mm
Depth: 126 to 206 mm
Depth: 126 to 206 mm
Industrial design
Depth: 126 to 206 mm
“T” Transoms
T-shaped
mullions
“T” expansion
mullions
T-shaped
transom
Wictec INTERNATIONAL_Mise en page 1 30/11/12 11:02 Page29
Standard cap profiles
Stainless steel
cap profiles
28
Cap on request (consult us, minimum quantity and leadtime)
Variable angle cap profiles
29
Wictec INTERNATIONAL_Mise en page 1 30/11/12 11:02 Page30
Technology for your ideas
It is our aim that as a WICONA partner, you are able
to distinguish yourself very clearly in the market
and therefore achieve greater success than your
competitors.
1I
That is why we are continually working to develop our
products and why our innovations are setting new
standards within the sector. This is what we call
'Technology for ideas'.
Wictec INTERNATIONAL_Mise en page 1 30/11/12 11:02 Page31
Innovations
Double-skin façades – twice the protection
2I
Duowall is a façade concept that opens up new approaches based
on WICONA systems. Today’s building market is determined as much
by ecological standards as by technical, functional, aesthetic and
economic criteria.
The basic concept of a second, non-insulated layer of glass in front of
an internal heat-insulated façade with opening vents can be achieved
using combinations of WICONA systems. The individual form is tailored
to the specific building in each case. You can rely on the WICONA
team to support you throughout your project, with the benefit of our
extensive experience and know-how.
TEmotion – The intelligent façade concept
TEmotion is an intelligent façade concept that has been developed by
WICONA incorporating active and self-sustaining building technology.
The façade reacts to changes in outdoor and indoor conditions, such
as light or temperature, significantly improving the energy efficiency
of the building envelope and reducing the operating costs.
TEmotion not only incorporates technical components, but also
includes the relevant sensors and control systems. The intelligent
façade controls the integrated ventilation, air-conditioning and heating
technology, adjusts the sun protection and prevents the interior from
overheating.
Automatically opened vents allow for night venting, considerably
reducing the costs of active cooling. In contrast to conventional
façades, using TEmotion saves 40 to 50 per cent of the primary
energy otherwise used for heating, cooling, ventilation and illumination.
Solar shading systems
WICSOLAIRE represents a comprehensive solution when it comes to
providing external solar protection. As the system allows fixed or
adjustable louvre blade orientation, the solar shading can be adjusted
perfectly to the building. This individual adjustability not only improves
the energy balance of the building, but also increases user comfort.
1 I Hochschule, Albstadt - Sigmaringen
Architect: Glück & Partner GmbH - Photo: WIcona Rights
2 I Zeppelin University, Friedrichshafen
Architect: Fritz Hack - Photo: Wicona Rights
30
31
Wictec INTERNATIONAL_Mise en page 1 04/12/12 09:40 Page32
Headquarters
Hydro Building Systems S.a.r.l.
270 rue Léon Joulin - BP 63709
31037 Toulouse cedex 01 - France
Phone +33 5 61 31 26 26
www.wicona-int.com
China
Hydro Building Systems Co. Ltd
5C-15 LIANDO
International Industry Park
Maju Bridge
Tongzhou District, Beijing, PRC
101102
Phone +8610 6059 5686
www.wicona.cn
Middle East
Hydro Aluminium QSTP-B
Qatar Science & Technology Park
P.O. Box 210216
Doha - Qatar
Phone +974 44 91 25 52
www.wicona-int.com
United Kingdom
Hydro Building Systems Ltd.
Silkwood Park
Wakefield WF5 PTG
United Kingdom
Phone +44 845 602 8799
www.wicona.co.uk
408.1209
www.wiconafinder.com