Architectural Binder

Transcription

Table of Contents
General Information |
WELCOME TO SCRANTON PRODUCTS®
Table of Contents
General Information
Vanities
• Welcome to Scranton Products
• Care & Maintenance
• Warranty Information
• MSDS Information
Sustainability
• Are Scranton Products materials Sustainable?
• Greenguard Certified Products
• Leed Information
Accredited Classes
Architectural
Toilet Compartments & Screens
Hiny Hider Partitions
• Case Study
• Specifications & Drawings
• Floor Mounted Overhead Braced
- Specifications
- Drawings
• Floor to ceiling
- Specifications
- Drawings
• Ceiling Hung
- Specifications
- Drawings
• Hiny Hider Urinal Screens
- Specifications
- Drawings
• Hiny Hider Hardware
- Hinges
- Drawings
- Brackets
- Drawings
- Shoes
- Drawings
- Headrails
- Drawings
- Door hardware
- Drawings
• Hiny Hider fire rating information
Resistall Partitions
• Case study
• Specifications
• Specifications
• Drawings
Shower & Dressing Compartments
• Specifications
• Drawings
Lockers
Tufftec Lockers
• Case Study
• Specifications
• Drawings
Tufftec Benches
• Specifications
• Drawings
Duralife Lockers
• Case study
• Specifications
• Drawings
• Fire rating information
Contact Information
TM
General Information
Designed to be worry free
GENERAL INFORMATION
• Industry leader
• Maintenance free solutions
• American made
• Sustainable
Welcome to Scranton Products
WELCOME TO SCRANTON PRODUCTS®
Together the brands of Scranton Products® offer the most comprehensive
and trusted line of innovative products that add functional and aesthetic value,
superior performance, durability, minimal maintenance, lower life cycle cost
and sustainability.
For more than 30 years, our American made premium brands have led the
market, setting new benchmarks for the industry in quality and innovation.
Our well-known brands include; Hiny Hider® Toilet Partitions, Tufftec Lockers®,
Resistall® Partitions, and Duralife LockersTM. They won’t dent, rust or need
painting, and because they are color throughout, delamination is not factor.
Specify and install Scranton Products® brands with confidence – the most
recognized and trusted names in locker systems, bathroom partitions, counter
tops, shower stalls and more.
Please note that we will automatically send periodic updates to our
architectural binder. In order to guarantee that you receive them, we ask
that you submit any change to your contact information such as mailing
address and e-mail address by contacting us at [email protected].
You may also contact us through our website or toll-free number for more
comprehensive information on our product lines and specifications, or to
request a complete color sample kit at www.scrantonrpoducts.com,
or 800.445.5148.
TM
Scranton Products Limited Warranty
SCRANTON PRODUCTS® LIMITED WARRANTY
Scranton Products’ Hiny Hider® Partitions, Resistall Partitions®, Tufftec Lockers®, Tufftec™ benches, Duralife
Lockers™, Scranton Products® brand shower stalls, dressing compartments and vanities, including products
sold under the company names (Santana©, Comtec©, Capitol©) (hereinafter “warranted products”) are
warranted by the manufacturer to a corporation or other commercial entity which purchases the partitions and
lockers for use in the conduct of its business to be free from defects in material and workmanship that (i) occur
as a direct result of the manufacturing process; (ii) occur under normal use and service; (iii) occur during the
warranty period; and (iv) result in breakage or delamination. Limited warranty periods are as follows:
Lockers/Benches
Tufftec Lockers ® Tufftec TM Benches Duralife Lockers TM 25 years
25 years
15 years
Bathroom Partitions
Hiny Hiders ® Bathroom Partitions Resistall ® Bathroom Partitions 25 years
5 years
Shower Stalls/Vanities/Dressing Compartments
Scranton Products ® Shower Stalls Scranton Products ® Vanities Scranton Products ® Dressing Compartments 25 years
25 years
25 years
This limited warranty is subject to the following conditions:
1. The warranted products have been installed in accordance with the manufacturer’s written instructions and drawings (as contained in the instruction sheet supplied with the order).
2. The limited warranty is effective only with regard to the original installation of the warranted products and not to any subsequent installation that has altered the warranted product without the consent of
the manufacturer. 3. The limited warranty shall not be applicable if the defect in the warranted product has resulted from any failure or defect in the building or substructure to which the warranted product is attached (including but not limited to settling, shifting, distorting, or movement of the walls or foundation of the structure), extraordinary wear and tear, violent action of the elements (such as sunlight, lightening, hurricane, tornado, or hail), vandalism, misuse, neglect, or improper handling of the warranted product, during or after installation, or improper or insufficient ventilation of the building to which the warranted product is attached.
TM
SCRANTON PRODUCTS® LIMITED WARRANTY
Subject to the above conditions, in the event that the warranted product or any portion thereof, is found to be
defective in workmanship or materials within limited warranty period from the date of receipt by customer,
the Manufacturer will repair or replace the defective material, or will refund the original purchase price of
the defective material. The choice of remedy is in Manufacturer’s sole discretion. The Manufacturer will not
be liable for labor and/or removal costs connected with the claim. Replacement product will be provided as
close to the original color and design as possible, although it is not guaranteed to match completely. In the
event of repair or replacement, the original limited warranty shall apply to the repaired or replaced portion of
the warranted products and will extend for the balance of the warranty period in effect at the time the material
proved defective.
THE WARRANTY STATEMENTS CONTAINED IN THIS LIMITED WARRANTY SET FORTH THE ONLY
WARRANTIES EXTENDED BY SCRANTON PRODUCTS AND ARE IN LIEU OF ALL OTHER CONDITIONS
AND WARRANTIES, EITHER EXPRESSED OR IMPLIED, INCLUDING WITHOUT LIMITATION, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE PROVISIONS
OF THIS WARRANTY SHALL CONSTITUTE THE ENTIRE LIABILITY OF SCRANTON PRODUCTS AND THE
PURCHASER/PROPERTY OWNER’S EXCLUSIVE REMEDY FOR BREACH OF THIS WARRANTY. IN NO
EVENT SHALL SCRANTON PRODUCTS BE LIABLE TO THE PURCHASER/PROPERTY OWNER FOR SPECIAL,
INCIDENTAL, INDIRECT, CONSEQUENTIAL, OR PUNITIVE DAMAGES ARISING FROM THE USE OF THE
WARRANTED PRODUCTS OR THE BREACH OF ANY EXPRESS OR IMPLIED WARRANTY. The laws of some
states and provinces do not allow the exclusion, limitation or variation of certain conditions or warranties
implied by legislation so the above limitations or exclusions may not apply to you. This Limited Warranty gives
you specific legal rights and you may also have other rights that vary from state to state and province
to province.
Any claim under such warranties must be made during the applicable warranty period and shall be asserted
by contacting: Scranton Products®, (Santana/Comtec/Capitol) 801 E. Corey Street-Scranton, PA 18505-Phone#
800-445-5148-Fax# 800-551-6993.
TM
Care & Maintenance
WORRY FREE MAINTENANCE
Keeping your plastic lockers and partitions beautiful for years is easy!
Here’s how
DIRT and GRAFFITI
Your Scranton Products plastic products can be cleaned
satisfactorily by using water and a mild cleaner. Avoid using any abrasive cleaner, brush or other item that could
scratch the surface.
When the soiled areas are stubborn, the following cleaning
solutions are suggested:
- ½ cup of household detergent, 2/3 cup of
trisodium phosphate, and 1 gallon of water
- Any industrial strength cleaner (Non-abrasive)
- For glue that sticks from the masking use
Mineral spirits or Acetone. Avoid contact with
the hardware.
CUT and SCRATCHES
Repair cuts and scratches by burnishing the surface with a smooth round object, such as a spoon
or screwdriver handle. Using the smooth round object, apply light pressure to the cut or
scratched surface rubbing it until it begins to heal.
NOTE: Spray the surface of the panels and doors with silicone to give them a like new bright and
glossy appearance.
Material Safety Data Sheet
MATERIAL SAFETY DATA SHEET
PETROTHENE LM600700
1. Product and Company Identification
Product name: Petrothene LM60070
Number: 000000000000504270
Chemical characterization: Polyolefin
CAS-No.: 9002-88-4
Chemical name: Polyethylene Homopolymer
Synonyms: Polyethylene, PE, Polyolefin
Use category: Resins
Company Address:
Equistar Chemicals, LP
LyondellBasell Tower, Suite 700
1221 McKinney St.
P.O. Box 2583
Houston, TX 77252-2583 Company Telephone:
Customer Service
888 777-0232
Product Safety
800 700-0946
[email protected]
Emergency Telephone
CHEMTREC USA 800-424-9300
EQUISTAR 800-245-4532
2. Hazards Identification
Emergency Overview
This material is NOT HAZARDOUS by OSHA Hazard Communication definition. Trade secret chemical identities will be
revealed to treating physicians in an emergency, or to purchasers after execution of a secrecy agreement.
Signal Word
Caution
NFPA®
HMIS®
Physical State
Solid
Color
Translucent to white
Health
Flammability
Physical Hazard
1
0
0
1
0
0
Odor
Faint, mild hydrocarbon odor
Odor Threshold
No value available
TM
MATERIAL SAFETY DATA SHEET
PETROTHENE LM600700
3. Potential Health Effects
Routes of Exposure
Eye. Inhalation. Skin
• Polyethylene Homopolymer 9002-88-4
Hot material may cause thermal burns. At process temperature, irritating fumes may cause soreness in the nose and
throat; coughing may result. Mechanical irritation possible.
• Additives
No known acute health effects
Skin
Molten polymer may cause thermal burns.
Inhalation
At process temperatures irritating fumes may be produced. Inhalation of process fumes and vapors may cause soreness in
the nose and throat and coughing “Nuisance dust” such as polymer dust typically exhibit no significant health effect when
they are reasonably controlled. Exposure to high concentrations of dust may cause slight irritation by mechanical action.
Eyes
Mechanical irritation is possible
Ingestion
Ingestion not likely route of exposure
Chronic Effects
No known chronic health effects
• Polyethylene, Homopolymer 9002-88-4
No known chronic health effects.
• Additives
No known chronic health effects
TM
Sustainability
Recycle–Reclaim–Reuse
SUSTAINABILITY
• Made from recycled materials
• Contains 25-100%
pre-consumer content
• 100% recyclable
• 100% post consumer material
content available
Are Scranton Products Sustainable
RECYCLE • RECLAIM • REUSE
• Made from recycled materials • Contains 25-100% pre-consumer content
• Factory responsible recycling • 100% recyclable
SUSTAINABLE MATERIALS
When you choose Scranton Products sustainable materials for your restrooms, lockers
and other applications, you are supporting a healthier environment. Scranton Products
High Density Polyethylene (HDPE) reduces environmental impact and offers both initial
and long-term improvements to the indoor air quality of your projects:
• Made from recycled materials
• 100% recyclable
• Contains 25-100% pre-consumer content
• GREEN-GUARD Children and Schools Certified SM
• No painting means no VOC emissions
• Improved air quality
• Impermeable to moisture
• Resists mold, mildew and fungus
• Resistant to bacteria
• Power-washable and steam cleanable
• No need for harmful chemical cleaners
• Decreased noise pollution
• Factory responsible recycling
Incorporating Scranton Products HDPE sustainable materials can contribute points
toward LEED certification.
Greenguard Certified Products
The GREENGUARD Certification Program helps manufacturers create--and
helps buyers identify--interior products and materials that have low chemical
emissions, improving the quality of the air in which the products are used.
When you choose Scranton Products you are supporting a healthier environment and healthier kids, Greenguard Children and
Schools certified, Scranton Products meet strict criteria for products intended for use in schools and other environments where
children spend significant periods of time.
In addition, because they never need painting, they do not contribute to VOC emissions, improving both indoor and outdoor air
quality. They are also impermeable to moisture, resist mold and mildew, and can be power washed or steam cleaned, eliminating
the need for harmful chemical cleaners. Incorporating Scranton Products can contribute to points toward LEED certification.
Below are some facts about the program
For products intended for use in schools, daycares or other environments where children spend significant periods of time, the GREENGUARD
Children & Schools Certification ProgramSM offers stricter certification criteria . It is referenced by both The Collaborative for High Performance Schools (CHPS) and the Leadership in Energy and Environmental Design (LEED) Building Rating System. Products certified to this
standard are also suitable for use in environments where children and others work, play or reside.
Body Burden Correction Factor
Children are more sensitive to environmental exposures than adults. Their bodies are still developing including their brains. They breathe
faster than adults and in return receive a higher dose of indoor pollution per body weight. To account for inhalation exposure to young
children, a body burden correction factor has been applied to the current GREENGUARD Indoor Air Quality Certified ® allowable levels. To
achieve GREENGUARD Children & Schools Certification, these lower allowable emissions criteria must be met along with additional
chemical criteria as discussed below.
Chronic Reference Exposure Levels (CRELs)
The exposure to individual volatile organic compounds (VOCs), as detected in the C 6 - C16 mass spectrometric analysis screen, has been adjusted to allow no greater than 1/100 of the currently published ACGIH® Threshold Limit Values (TLVs) and no greater than one-half of the
California's Chronic Reference Exposure Levels (CRELs). In many cases, the 1/100 safety factor reduction of TLVs results in the most stringent requirements for an extensive range of VOCs. A total VOC or TVOC maximum allowable limit takes into account the complex mixture of all VOCs found to be emitting from a product, including those with and without TLVs or CRELs.
Limits on Phthalates
Limits on emissions of total phthalates, consisting of dibutyl (DBP), diethylhexyl (DEHP), diethyl (DEP), dimethyl (DMP), butylbenzyl (BBP) and
dioctyl (DOP) phthalates, have been added to the list of requirements for GREENGUARD Children & Schools Certification. Results from
recent research indicate that inhalation is an important route of exposure to phthalates and that these chemicals have been associated
with endocrine disorders, reproductive and developmental disorders, asthma and allergies.
Emission Controls for Educational and Healthcare Environments
This standard is designed to define low-emitting materials suitable for environments where people, particularly children and sensitive adults,
spend extended periods of time, in particular schools and healthcare facilities.
www.scrantonproducts.com — 800.445.5148 — [email protected]
Leed Information
Several years ago Scranton Products established programs to recycle production scrap and waste. Today Scranton Products is
pleased to join the efforts of the U. S. Green Building Council and LEED program to improve the environmental and economic
performance of commercial construction projects.
The LEED program certifies buildings that meet standards utilizing energy and environmental design. The use of Scranton
Products’ solid HDPE plastic products can contribute LEED points in specific categories.
Construction Waste Management-Salvage/Recycle 50% or 75%;
MR Credit 2.1 and 2.2; 1 – 2 points credit
Scranton Products offers a program by which all unwanted solid HDPE plastic products they manufacture could be returned
for recycling.
Recycled Content MR Credit 4.1 and 4.2 1 – 2 points credit
Scranton Products offers products of 100% *Post Consumer Recycled
HDPE solid plastic in a variety of colors, and standard HDPE solid plastic products of 25% - 75% *post industrial recycled
HDPE.
Local, Regional Material MR Credit 5.1 and 5.2 1 – 2 points credit
Scranton Products, fabricates products in Scranton, PA 18505
The standard color pallet for the 100% post consumer partition products includes: PC 00 Grey, PC 02 Desert Beige, PC 05
Midnight Black and PC BB01 Blueberry. Matching shoes and brackets are available for these color selections providing a uniform design presentation.
Scranton Products can also offer 100% *post consumer partitions in custom colors on projects of approximately 40 stalls or
more.
VOLATILE ORGANIC COMPOUNDS (VOCs)
Scranton Products solid toilet partitions and lockers do not emit volatile organic compounds (VOCs).
UREA FORMALDEHYDE
Scranton Products solid toilet partitions and lockers do not contain urea formaldehyde.
*Post-consumer material is defined as waste material generated by households or by commercial, industrial and institutional facilities in their role as end-users of the product,
which can no longer be used for its intended purpose.
*Pre-consumer material (also referred to as post-industrial material) is defined as material diverted from the waste stream during the manufacturing process. Reutilization of
materials (i.e., rework, regrind or scrap generated in a process
and capable of being reclaimed within the same process that generated it) is excluded.
www.scrantonproducts.com — 800.445.5148 — [email protected]
AIA Courses
Providing valuable continuing education credits
AIA COURSES
• Lunch & Learn programs
• Online programs
• Webinars
• Self administered programs
Toilet Compartments & Screens
The possiblities are limitless
TOILET COMPARTMENTS & SCREENS
• Maintenance Free
• Impact & Dent Resistant
• Graffiti Resistant
• Will never rust, corrode
or delaminate
Hiny Hiders Toilet Partitions
HINY HIDERS® TOILET PARTITIONS
One investment many benefits
• 1” solid plastic
• Wide array of colors & textures
• Customizable
• Most durable material choice
Hiny Hider Case Study
CASE STUDY
OKLAHOMA STATE UNIVERSITY
In a sports stadium, there are fewer high-traffic areas than the restroom facilities. Oklahoma State
University’s historic stadium was built in 1913 so the restroom facilities had suffered a great deal of wear
and tear from continued use over the years. So when the University planned to renovate and expand its
stadium, it was an opportunity to upgrade the restrooms with new bathroom partitions that would add
functional and aesthetic value, and endure the high volume of traffic.
Oklahoma State University Hiny
Hiders Bathroom Partitions
“Durability was of utmost importance when selecting a product for this application,” said
David Reed, Sparks Reed Architecture & Interiors, project architect for the OSU installation.
“But due to the nature of the application we also wanted a product that would be low maintenance, and resistant to abuse. It’s common knowledge that public bathroom facilities, particularly the stalls, are subjected to vandalism including scratches and dents and graffiti
from rival or rowdy fans. We did our research and specified Scranton Products’ Hiny Hiders® for the application.”
Hiny Hiders are made from premium, American-made one-inch thick solid HDPE. The solid
plastic partitions resist dents, scratches, corrosion, bacteria, graffiti, and mildew, and unlike traditional
metal partitions, they’ll never rust. With the number of partitions required in the installation it was a
challenge to find the material that would last. Solid plastic will not break, and it never needs to be painted.
www.scrantonproducts.com ● 800.445.5148 ● [email protected]
CASE STUDY
Hiny Hiders are made from premium, American-made one-inch thick
solid HDPE. The solid plastic partitions resist dents, scratches, corrosion,
bacteria, graffiti, and mildew, and unlike traditional metal partitions, they’ll never
rust. With the number of partitions required in the installation it was a challenge
to find the material that would last. Solid plastic will not break, and it never
needs to be painted.
Hiny Hiders are available in a multitude of colors and textures however
Reed took advantage of the product’s customization capabilities and specified
the bathroom partitions be designed in the university’s school colors. In
addition, to make the application even more unique, the door of each stall is
personalized with the OSU logo.
More than 500 partitions were installed in the new stadium. Today,
according to Donald Clark, facility manager, the Hiny Hiders partitions have
proven to be low“Routing the logo into each door shows the
maintenance. “Our metal
workability of HDPE,” said Reed. “We were able to
stalls rusted, needed
provide the university and the fans with a
painting and graffiti was
unique custom product for the new
often a problem. Since
the Hiny Hiders were
facility,” said Reed. “The color is bright
orange and the logo supports college spirit and fan installed we’ve had
virtually no maintenance
excitement.”
issues in any of the
restroom stalls. The most we’ve had to do is wash them down with a garden
hose.”
As Hiny Hiders are made with HDPE, they’ll have a long life cycle and
be a cost-effective component to the new stadium. This is key in a stadium that
has more than 40 restroom facilities. For OSU, such a large application, this is
an enormous benefit.
Since the 2009 installation, the Hiny Hiders have endured the cheers
and jeers of sports fans. “The bathroom partitions have really shown their
durability while retaining their great looks,” said Clark. “Every hinge, every latch,
every hanger works as well today as it did three years ago,” he said.
For Oklahoma State University, the plan to renovate the stadium was to
transform a structure that was showing its age into a contemporary, state-of-theart facility. The goal was to create unrivaled facilities for football players and
fans alike. Boone Pickens Stadium can now be
considered one of America's top facilities from top to
bottom.
Hiny Hider Specifications & Drawings
SPECIFICATIONS & DRAWINGS
Hiny Hider Floor-Mounted Overhead-Braced
FLOOR-MOUNTED OVERHEAD-BRACED
Our strongest and most adaptable
layout type works with any
bathroom configuration.
Hiny Hider Floor Mounted Overhead Braced Specifications
Toilet Compartments & Screens | Hiny Hiders® Toilet Partitions | Specifications & Drawings |
Solid Plastic Toilet Compartments Specifications - Section 10 2116
PART 1 - GENERAL
1.1 SUMMARY
A. Section Includes:
1. Solid plastic [toilet compartments] [urinal screens] [privacy screens] [and] [entry partitions].
B. Related Sections:
1. Division 01: Administrative, procedural, and temporary work requirements.
1.2 REFERENCES
A. ASTM International (ASTM):
1. A167 - Standard Specification for Stainless and Heat-Resisting Chromium-Nickel Steel Plate, Sheet,
and Strip.
2. B221 - Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles,
and Tubes.
3. E84 - Standard Test Method for Surface Burning Characteristics of Building Materials.
B. National Fire Protection Association (NFPA) 286 - Standard Methods of Fire Tests for Evaluating Contribution
of Wall and Ceiling Interior Finish to Room Fire Growth.
1.3 SYSTEM DESCRIPTION
A. Compartment Configurations:
1. [Toilet partitions] [privacy screens] and [entry partitions]: Floor mounted, overhead braced.
2. Urinal screens: [Wall] [Floor] mounted.
1.4 SUBMITTALS
A. Submittals for Review:
1. Shop Drawings: Include dimensioned layout, elevations, trim, closures, and accessories.
2. Product Data: Manufacturer’s descriptive data for panels, hardware, and accessories.
3. Samples: [2 x 3] [__ x __] inch samples [showing available colors.] [in each color.]
B. Sustainable Design Submittals:
1. Recycled Content: Certify percentages of post-consumer and pre-consumer recycled content.
2. Regional Materials: Certify distance between manufacturer and Project and between manufacturer
and extraction or harvest point in miles.
1.5 QUALITY ASSURANCE
A. Manufacturer Qualifications: Minimum [5] [__] years experience in manufacture of solid plastic toilet
compartments with products in satisfactory use under similar service conditions.
B. Installer Qualifications: Minimum [5] [__] years experience in work of this Section.
1.6 WARRANTIES
A. Provide manufacturer’s 25 year warranty against breakage, corrosion, and delamination under
normal conditions.
PART 2 - PRODUCTS
2.1 MANUFACTURERS
A. Contract Documents are based on products by Scranton Products. (www.scrantonproducts.com)
B. Substitutions: [Under provisions of Division 01.] [Not permitted.]
2.2 MATERIALS
A. Doors, Panels and Pilasters:
1. Solid Plastic fabricated from polymer resins compounded under high pressure, forming single
thickness panel.
2. Waterproof and nonabsorbent, with self-lubricating surface, resistant to marks by pens, pencils,
markers, and other writing instruments.
3. 1 inch thick with edges rounded to 1/4 inch radius.
4. Recycled content: Minimum [25] [__] percent.
5. Fire hazard classification: Not required.
**** OR ****
6. Fire hazard classification: Class [A] [B] flame spread/smoke developed rating, tested to ASTM E84.
**** OR ****
7. Fire hazard classification: Pass NFPA 286.
8. Color: [____.] [To be selected from manufacturer’s full color range.]
B. Aluminum Extrusions: ASTM B221, 6463-T5 alloy and temper.
C. Stainless Steel: ASTM A167, Type 304.
2.3 HARDWARE
A. Hinges:
1. 8 inches long, fabricated from heavy-duty extruded aluminum with bright dip anodized finish, wraparound flanges, adjustable on 30-degree increments, through bolted to doors and pilasters
with stainless steel, Torx head sex bolts.
2. Hinges operate on field-adjustable nylon cams, field adjustable in 30 degree increments.
**** OR ****
B. Hinges: Stealth integral hinge from door and pilaster material with exposed metal parts on interior of stall.
**** OR ****
C. Hinges: Regal hinge fabricated from heavy-duty cast aluminum, wrap around flanges, adjustable on
30-degree increments, through bolted to doors and pilasters.
D. Door Strike and Keeper:
1. 6 inches long, fabricate from heavy-duty extruded aluminum with bright dip anodized finish, with
wrap-around flanges secured to pilasters with stainless steel tamper resistant Torx head sex bolts.
2. Bumper: Extruded black vinyl.
E. Latch and Housing:
1. Heavy-duty extruded aluminum.
2. Latch housing: Bright dip anodized finish.
3. Slide bolt and button: Black anodized finish.
**** OR ****
4. Slide latch and paddle.
F. Coat Hook/Bumper:
1. Combination type, chrome plated Zamak.
2. Equip outswing handicapped doors with second door pull and door stop.
G. Door Pulls: Chrome plated Zamak.
2.4 COMPONENTS
A. Doors and Dividing Panels: 55 inches high, mounted 14 inches above finished floor, [with aluminum heat-sinc
fastened to bottom edges.]
B. Pilasters: 82 inches high, fastened to pilaster sleeves with stainless steel tamper resistant Torx head sex bolt.
C. Pilaster Sleeves: 3 inches high, [one-piece molded HDPE,] [20 gage stainless steel,] secured to pilaster with
stainless steel tamper resistant Torx head sex bolt.
D. Wall Brackets: 54 inches long, [Extruded PVC,] [heavy-duty aluminum, bright dip anodized finish,] fastened to
pilasters and panels with stainless steel tamper resistant Torx head sex bolts.
E. Headrail: Heavy-duty extruded aluminum, anti-grip design, clear anodized finish, fastened to headrail
bracket with stainless steel tamper resistant Torx head sex bolt and at top of pilaster with stainless steel tamper
resistant Torx head screws.
F. Headrail Brackets: 20 gage stainless steel, satin finish, secured to wall with stainless steel tamper resistant Torx
head screws.
PART 3 EXECUTION
3.1 INSTALLATION
A. Install compartments in accordance with manufacturer’s instructions and approved Shop Drawings.
B. Install rigid, straight, plumb, and level.
C. Locate bottom edge of doors and panels 14 inches above finished floor.
D. Provide uniform, maximum 3/8 inch vertical clearance at doors.
E. Not Acceptable: Evidence of cutting, drilling, or patching.
3.2 ADJUSTING
A. Adjust doors and latches to operate correctly.
Hiny Hider Floor Mounted Overhead Braced Drawings
8” Aluminum Wrap-Around Hinge Continuous Aluminum Brackets
PLAN ELEVATION
FRONT ELEVATION
FLOOR MOUNT
SIDE ELEVATION
HEADRAIL BRACE
NOTE: Job-Specific Specifications for all orders are located on shop drawing layouts.
* HEATSINC: Heatsinc is to be placed on the bottom of the panels & doors. (If specified)
(Drawings are not to scale)
Drawing shown with 8” wrap-around hinge. Please see individual section for all hardware options.
Drawings for all configuration options are available at www. scrantonproducts.com
and on the memory stick attatched to the binder.
8” Aluminum Wrap-Around Hinge Stirrup Brackets
PLAN ELEVATION
SIDE ELEVATION
FRONT ELEVATION
FLOOR MOUNT
HEADRAIL BRACE
Floor-Mounted overhead-Braced
Regal Hinge Continuous Aluminum Brackets
PLAN ELEVATION
FRONT ELEVATION
Floor MOUNT
SIDE ELEVATION
Headrail BRACE
Regal Hinge Stirrup Brackets
PLAN ELEVATION
FRONT ELEVATION
Floor MOUNT
SIDE ELEVATION
Headrail BRACE
Stealth Integral Hinge Continuous Aluminum Brackets
PLAN ELEVATION
FRONT ELEVATION
Floor MOUNT
SIDE ELEVATION
Headrail BRACE
Stealth Integral Hinge Stirrup Brackets
PLAN ELEVATION
FRONT ELEVATION
Floor MOUNT
SIDE ELEVATION
Headrail BRACE
54” Stainless Steel Continuous Helix Hinge Continuous Aluminum Brackets
PLAN ELEVATION
FRONT ELEVATION
Floor MOUNT
SIDE ELEVATION
Headrail BRACE
54” Stainless Steel Continuous Helix Hinge Stirrup Brackets
PLAN ELEVATION
FRONT ELEVATION
Floor MOUNT
SIDE ELEVATION
Headrail BRACE
54” Stainless Steel Continuous Spring Hinge Continuous Aluminum Brackets
PLAN ELEVATION
FRONT ELEVATION
Floor MOUNT
SIDE ELEVATION
Headrail BRACE
54” Stainless Steel Continuous Spring Hinge Stirrup Brackets
PLAN ELEVATION
FRONT ELEVATION
Floor MOUNT
SIDE ELEVATION
Headrail BRACE
54” Surface Mounted Aluminum Continuous Hinge Continuous Aluminum Brackets
PLAN ELEVATION
FRONT ELEVATION
SIDE ELEVATION
Floor MOUNT
Headrail BRACE
54” Surface Mounted Aluminum Continuous Hinge Stirrup Brackets
PLAN ELEVATION
FRONT ELEVATION
Floor MOUNT
SIDE ELEVATION
Headrail BRACE
Hiny Hider Floor To Ceiling
FLOOR TO CEILING
Offers a unique aesthetic in which
pilasters run directly from floor to ceiling.
Hiny Hider Floor To Ceiling Specifications
FLOOR TO CEILING
PART 1 - GENERAL
1.1 SUMMARY
1.2 REFERENCES
and Strip.
and Tubes.
1. [Toilet partitions] [privacy screens] and [entry partitions]: Floor-to-ceiling
1.4 SUBMITTALS
1.6 WARRANTIES
normal conditions.
PART 2 - PRODUCTS
2.1 MANUFACTURERS
FLOOR TO CEILING
2.2 MATERIALS
thickness panel.
**** OR ****
**** OR ****
2.3 HARDWARE
A. Hinges:
**** OR ****
**** OR ****
**** OR ****
FLOOR TO CEILING
2.4 COMPONENTS
head screws.
PART 3 EXECUTION
3.1 INSTALLATION
3.2 ADJUSTING
Hiny Hider Floor To Ceiling Drawings
FLOOR to Ceiling
PLAN ELEVATION
SIDE ELEVATION
FRONT ELEVATION
FLOOR MOUNT
CEILING MOUNT
FLOOR to Ceiling
8” Aluminum Wrap-Around Hinge Stainless Steel Stirrup Brackets
PLAN ELEVATION
SIDE ELEVATION
FRONT ELEVATION
FLOOR MOUNT
CEILING MOUNT
Floor to Ceiling
PLAN ELEVATION
FRONT ELEVATION
Floor MOUNT
SIDE ELEVATION
Ceiling Mount
Floor to Ceiling
Regal Hinge Stirrup Brackets
PLAN ELEVATION
FRONT ELEVATION
Floor MOUNT
SIDE ELEVATION
Ceiling Mount
Floor to Ceiling
PLAN ELEVATION
FRONT ELEVATION
Floor MOUNT
SIDE ELEVATION
Ceiling Mount
Floor to Ceiling
Stealth Integral Hinge Stirrup Brackets
PLAN ELEVATION
FRONT ELEVATION
Floor MOUNT
SIDE ELEVATION
Ceiling Mount
Floor to Ceiling
PLAN ELEVATION
FRONT ELEVATION
Floor MOUNT
SIDE ELEVATION
Ceiling Mount
Floor to Ceiling
54” Stainless Steel Continuous Helix Hinge Stirrup Brackets
PLAN ELEVATION
FRONT ELEVATION
Floor MOUNT
SIDE ELEVATION
Ceiling Mount
Floor to Ceiling
54” Stainless Steel Spring Loaded Hinge Continuous Aluminum Brackets
PLAN ELEVATION
FRONT ELEVATION
Floor MOUNT
SIDE ELEVATION
Ceiling Mount
Floor to Ceiling
54” Stainless Steel Spring Loaded Hinge Stirrup Brackets
PLAN ELEVATION
FRONT ELEVATION
Floor MOUNT
SIDE ELEVATION
Ceiling Mount
Floor to Ceiling
54” Aluminum Continuous Hinge Continuous Aluminum Brackets
PLAN ELEVATION
FRONT ELEVATION
Floor MOUNT
SIDE ELEVATION
Ceiling Mount
Floor to Ceiling
54” Aluminum Continuous Hinge Stirrup Brackets
PLAN ELEVATION
FRONT ELEVATION
Floor MOUNT
SIDE ELEVATION
Ceiling Mount
Hiny Hider Ceiling Hung
CEILING HUNG
Ideal for installations requiring
no obstructions on floor for easier
maintenance.
Hiny Hider Ceiling Hung Specifications
CEILING HUNG
PART 1 - GENERAL
1.1 SUMMARY
1.2 REFERENCES
and Strip.
and Tubes.
1. [Toilet partitions] [privacy screens] and [entry partitions]: Ceiling hung
1.4 SUBMITTALS
1.6 WARRANTIES
normal conditions.
PART 2 - PRODUCTS
2.1 MANUFACTURERS
CEILING HUNG
2.2 MATERIALS
thickness panel.
**** OR ****
**** OR ****
2.3 HARDWARE
A. Hinges:
**** OR ****
**** OR ****
**** OR ****
CEILING HUNG
2.4 COMPONENTS
head screws.
PART 3 EXECUTION
3.1 INSTALLATION
3.2 ADJUSTING
Hiny Hider Ceiling Hung Drawings
Ceiling hung
PLAN ELEVATION
SIDE ELEVATION
FRONT ELEVATION
CEILING MOUNT
CROSSBRACE
Ceiling hung
CEILING BOLT DETAIL
Please note that the height to the top of the
steel can be no more than 2 3/4”higher from
the finished ceiling.
CEILING HUNG Ceiling Beam can only be structural steel.
No other types are recommended.
Only 6 1/2” threaded rods are recommended.
Ceiling Hung
PLAN ELEVATION
FRONT ELEVATION
Ceiling MOUNT
SIDE ELEVATION
CROSS BRACE
Ceiling Hung
CEILING BEAM
Attention (provide the following)
Floor to finished ceiling height: ___________
Please note that the height to the top of the steel can be no more than 2 3/4” higher from the finished ceiling.
(See the above detail)
Ceiling Beam can only be structural steel.
(Note: Unistrut is not considered structural steel and should not be used.)
Ceiling Hung
PLAN ELEVATION
FRONT ELEVATION
Ceiling MOUNT
SIDE ELEVATION
CROSS BRACE
Ceiling Hung
CEILING BEAM
Ceiling Hung
PLAN ELEVATION
FRONT ELEVATION
Ceiling MOUNT
SIDE ELEVATION
CROSS BRACE
Ceiling Hung
CEILING BEAM
Ceiling Hung
PLAN ELEVATION
FRONT ELEVATION
Ceiling MOUNT
SIDE ELEVATION
CROSS BRACE
Ceiling Hung
CEILING BEAM
Ceiling Hung
54” Surface Mounted Aluminum Hinge Continuous Aluminum Brackets
PLAN ELEVATION
FRONT ELEVATION
Ceiling MOUNT
SIDE ELEVATION
CROSS BRACE
Ceiling Hung
54” Surface Mounted Aluminum Hinge Continuous Aluminum Brackets
CEILING BEAM
Hiny Hider Screens
SCREENS
Hiny Hider Urinal Screens Specifications
SCREENS
PART 1 - GENERAL
1.1 SUBMITTALS
A. Plastic compartment work includes the following, where indicated:
1. Solid Plastic Privacy Screens
B. Furnish all labor and materials necessary for the completion of work in this section as shown on the contract
drawings and specified herein.
C. Work in this section shall include, but is not limited to:
1. Privacy screens
2. Hardware for privacy screens
3. Shop drawings and working drawings
4. Manufacturers guarantee
D. Related work specified elsewhere shall include accessories and anchorage/blocking for attachment of
privacy screens.
1.2 PRODUCT DATA
1. Submit six (6) sets of shop drawings and details for architect’s approval
2. Colors shall be selected from the manufacturer’s full range of colors.
3. Color samples and hardware samples shall be submitted for approval by the architect upon request.
B. Installer Qualifications: Minimum [5] [__] years experience in work of this Section
1.4 WARRANTIES
normal conditions.
PART 2 - PRODUCTS
2.1 MANUFACTURERS
2.2 MATERIALS
1. Privacy screens and optional pilasters shall be 1” thick constructed from solid plastic compounded
under high pressure.
**** OR ****
SCREENS
**** OR ****
2.3 HARDWARE
A. Overhead braced pilasters and floor supported pilasters (if required) shall have pilaster shoes 3” high and
made of one-piece molded plastic [Color to be selected from manufacturers full color range] OR pilaster shows
shall be 3” high (type 304, 20 gauge) stainless steel. Pilaster shoes shall be secured to the pilaster and secured
to the pilaster with a stainless steel tamper resistant torx head sex bold.
B. Floor to ceiling pilasters (if required) shall have a stainless steel angle bracket used to attached pilasters
at floor and ceiling in lieu of shoes. These angle brackets shall be attached to pilasters with ¾” stainless steel
tamper resistant torx head screws. Pilaster sleeves shall be 4” high stainless steel (type 304, 20 gauge) and
secured to pilasters with a stainless steel tamper resistant torx head sex bolt. Sleeves shall conceal the angle
brackets connections at the floor and ceiling.
C. Wall brackets shall be 41” or 54” long, made of extruded PVC plastic [Color to be selected from
manufacturers full color range]. These plastic brackets are fastened to the pilaster with stainless steel tamper
resistant torx head screws and fastened ot the panels with stainless steel tamper resistant torx head sex bolts.
OR, wall brackets shall be 1 ½” stirrup type made of heavy-duty aluminum (6463-T5 alloy) with a bright dip
anodized finish. Stirrup brackets shall be fastened to pilasters and panels with stainless steel tamper resistant
torx head sex bolts.
D. Headrail ((used with optional 82” pilasters only) shall be made of heavy-duty extruded aluminum (64630T4
alloy) with anti-grip design and integrated curtain track. The headrail shall have a clear anodized finish and shall
be fastened to the headrail bracket by a stainless steel tamper resistant torx head sex bolt, and fastened at the
top of the pilaster with stainless steel tamper resistant torx head screws.
E. Headrail brackets (required with headrail) shall be 20 gauge stainless steel with a sation finish and secured to
the wall with a stainless steel tamper resistant torx head screws.
2.4 CONSTRUCTION
A. Panels (and pilasters if required) shall be 1” thick with all edges rounded to a ¼” radius.
B. Panels shall be typically 42” or 55” high, mounted at 14” above the finished floor. An aluminum heat sinc may
be fastened to the bottom edges (optional)
C. Pilasters (if required) shall typically be 56”, 69” or 82” high and fastened into a 3” high pilaster show with
stainless steel angle bracket and sleeve.
PART 3 - EXECUTION
3.1 PREPARATION
A. Examine areas to receive screens for correct height and spacing of anchorage/blocking and plumbing
fixtures that may affect installation of screens. Report any discrepancies to the architect.
B. Take complete and accurate measurements of complete screen locations.
C. Start of work constitutes acceptance of job.
3.2 INSTALLATION
A. Install partitions rigid, straight, plumb, and level manor with plastic laid out as shown on shop drawings and
manufacturer’s installation instructions.
B. All panels shall typically be mounted at 14” above finished door
C. No evidence of cutting, drilling and/or patching shall be visible on the finished work
D. Finished surfaces shall be cleaned after installation and be left free of all imperfections.
Hiny Hider Urinal Screens Drawings
screens
18” x 42” Urinal Screen Elevations Stirrup Brackets
WALL HUNG
FLOOR SUPPORTED
FLOOR TO CEILING
HEADRAIL BRACED
NOTES:
NOTES:
1. Standard Screens sizes are 24” x 42”
and 18” x 42” although custom sizes are
available upon request.
2. Any screen over 30” is recommended to
have a floor supported pilaster.
screens
WALL HUNG
FLOOR SUPPORTED
FLOOR TO CEILING
HEADRAIL BRACED
NOTES:
NOTES:
screens
WALL HUNG
FLOOR SUPPORTED
FLOOR TO CEILING
HEADRAIL BRACED
NOTES:
NOTES:
screens
48” Urinal Screen Elevations Stirrup Brackets
WALL HUNG
FLOOR SUPPORTED
FLOOR TO CEILING
HEADRAIL BRACED
NOTES:
NOTES:
screens
55” Urinal Screen Elevations Stirrup Brackets
WALL HUNG
FLOOR SUPPORTED
FLOOR TO CEILING
HEADRAIL BRACED
NOTES:
NOTES:
Hiny Hider Hardware
HARDWARE
Continuous Brackets
Strikes
54” Plastic or Stainless Steel•; 54” or 68” Aluminum
6” Aluminum
Double Ear
Single Ear
54” or 71” Continuous
Aluminum•
Stirrup Brackets
Head Rail
Latches
Aluminum or Stainless Steel
Aluminum
Aluminum or Stainless Steel•†
Double Ear
Single Ear
Shoes
Plastic Pilaster††
3” Stainless Steel
emergency access
Hinges
Stainless Steel
8” Wrap Around
54”, 65”, 71”
Continuous
Aluminum•
54”, 65”, 71”
Continuous Stainless
Steel Helix•
Regal Hinge
•Optional hardware † Stainless steel option varies from aluminum hardware shown. †† Limited colors available.
54”, Continuous
Stainless Steel
Spring Loaded•
Stealth Integral
Hinge
Hiny Hider Hinges
HINGES
Hinges are offered in a variety of
different styles, no sight and continuous
options to meet any need.
Hiny Hider Hinges Drawings
hinges
8” Aluminum Wrap Around
NOTES:
Shown is the heavy duty extruded aluminum (6463-T5 alloy)
8” wrap around hinge as supplied by Scranton Products.
The hinge has a bright dipped anodized finish.
The top hinge (as shown) contains the cam mechanism
in it to insure that the door returns fully closed.
Hinges can be adjusted in the field for proper operation.
hinges
8” Aluminum Wrap Around - Surface Mount
NOTES:
8” surface mounted hinge as supplied by Scranton Products.
A 1/2” cardboard spacer is placed on the nylon pin between
the two parts of the bottom hinge, so that there is enough room
for the lower half of the bottom hinge to move up with the cam
action in the top hinge. (Note: This spacer cannot be removed
until after the hinges are installed.)
hinges
8” Surface Mount Hinge Solid Plastic Mount
PLAN ELEVATION - INSWING
STEP #1
PLAN ELEVATION - OUTSWING
STEP #2
STEP #3
Surface Mounted Hinge
Installation Instructions
1. Using the supplied 2 1/2” torx head screws attach panel to
wall at 14” above the finished floor standard.
2. See Installation Booklet for hinge attachment to the door.
3. Using Scranton Products Installation Instructions Booklet for
reference, attach the hinges to the surface mounted panel
using the 3/4” torx screws.
hinges
8” Surface Mount Hinge Direct Wall Mount
Use Scranton Products Installation Instructions Booklet
for attachment.
hinges
Regal Hinge System
Shown is the aluminum Regal hinge assembly.
The kit comes complete with (4) Regal hinges,
(2) Left hand plates, (2) Right hand plates, (4) Femal cam
bushings, (1) dummy pin, (1) Cam insert, and Fasteners.
Colors available: Smoke, Ember or Frost
Regal Hinge
Slider Latch
Regal & Slider Latch comes in three color options:
Ember, Smoke, and Frost.
hinges
Stealth Integral Hinge
Stealth “L” Brackets:
Are always to be mounted on the inside of
the toilet compartment and flush with door edge.
Stealth “L” Brackets:
Chrome Plated Steel
Note:
Stealth Integral Hinge
Shown is Scranton Products Stealth Integral hinge system.
The pilaster and door are manufactured to accept the nylon
Integral hinge.
hinges
54”, 65” or 71” Surface Mounted Aluminum Continuous Hinge
Note:
Shown is the 54”, 65” or 71” continuous heavy duty extruded
aluminum (6463-T5 alloy) hinge as supplied by Scranton Products.
Hinge can only be set to close position.
This hinge is spring loaded and is made to help the door close.
Note: All continuous hinges are NON-Handed and Not Adjustable.
hinges
54”, 65”, or 71” Aluminum Continuous Hinge - Surface Mounted
INSWING
OUTSWING
1. Using the supplied 2 1/2” torx head screws attach the 5” x 55”
panel to the wall at 14” above the finished floor, standard.
2. Using the 3/4” ST/ST torx screw attach the hinge to the panel.
3. Using the 3/4” ST/ST torx screw attach the door to the hinge
with an approx. 1/8” gap between the door and panel surface.
(fig. A or fig. B)
hinges
54” or 65” Continuous Stainless Steel Helix Hinge
54” or 65” Helix Hinge
The 54”, 65” helix hinge is made
from 14 gauge, #304 stainless
steel. The helix hinge contains
a 1/4” stainless steel pin that is
welded and ground. This hinge
comes with a brushed finish and
is pre-drilled.
Hinge has 2 options: in-swing or
out-swing. In-swing is set open
at 15 degrees open. Out-swing is
set in closed position.
or 65”
hinges
54” or 65” Stainless Steel Helix Hinge - Surface Mounted
INSWING
OUTSWING
(fig. A or fig. B)
hinges
54” Stainless Steel Spring Hinge
Note:
Shown is Scranton Products 54”
Stainless Steel spring loaded hinge.
The hinge is made from 16 gauge
#304 stainless steel and is pre-drilled.
hinges
54” Stainless Steel Spring Hinge - Surface Mounted
INSWING
OUTSWING
(fig. A or fig. B)
Hiny Hider Brackets
BRACKETS
Brackets are offered in continuous or
stirrup & are made from aluminum,
plastic or stainless adding strength to
any installation.
Hiny Hider Bracket Drawings
Brackets
Aluminum or Stainless Steel Single-Ear Stirrup Bracket
Note:
Shown is Scranton Products heavy duty extruded
aluminum (6463-T5 alloy) single ear stirrup bracket.
The bracket has a bright dipped anodized finish.
Brackets
Aluminum or Stainless Steel Double-Ear Stirrup Bracket
Note:
Shown is Scranton Products heavy duty extruded
aluminum (6463-T5 alloy) double ear stirrup bracket.
The bracket has a bright dipped anodized finish.
Brackets
41”, 54” or 68” Aluminum Continuous Single-Ear Bracket
Note:
Shown is the 54” heavy
duty extruded aluminum
(6463-T5 alloy) single ear
continuous wall bracket.
The bracket has a bright
dipped anodized finish.
Brackets
41”, 54” or 68” Aluminum Double Ear Continuous Bracket
Note:
Shown is the 54” heavy
duty extruded aluminum
(6463-T5 alloy) double ear
continuous wall bracket.
The bracket has a bright
dipped anodized finish.
Brackets
41” or 54” Plastic or Stainless Steel Single Ear Continuous Bracket
Note:
Shown is the 54” plastic
continuous bracket extruded
from pvc plastic.
This is standard hardware
supplied by Scranton products.
Brackets
41” or 54” Plastic or Stainless Steel Double Ear Continuous Bracket
Note:
Shown is the 54” plastic
continuous bracket extruded
from pvc plastic.
This is standard hardware
supplied by Scranton products.
Hiny Hider Shoes
SHOES
One piece construction pilaster shoes
are offered in durable stainless steel and
plastic options.
Hiny Hider Shoe Drawings
shoes
Plastic Pilaster Shoe
Note:
Shown is the plastic pilaster shoe, made from high density
polyethylene (HDPE) resins, which are injection molded into
shoes ranging in sizes from 3” up to 12” wide in 1” increments,
and 14” to 24” wide in even sizes only.
Details
shoes
Stainless Steel Pilaster Shoe
Note:
Shown is the stainless steel (type 201-20 gauge) pilaster shoe
ranging in lengths from 3” wide up to 24” wide in 1” increments,
and 14” wide to 24” wide in even sizes only.
The shoes have a satin finish on all exposed surfaces.
Details
SLEEVE
Stainless Steel Pilaster Sleeve
Note:
Shown is the stainless steel (type 201-20 gauge) pilaster sleeve
ranging in lengths from 3” wide up to 24” wide in 1” increments,
and 14” wide to 24” wide in even sizes only.
The sleeves have a satin finish on all exposed surfaces.
FLOOR MOUNT
CEILING MOUNT
Hiny Hider Headrails
HEADRAILS
An anti-grip profile deters unintended
use and maintains safety. Where
desired, an integrated shower curtain
track accomodates optional shower
curtain hooks.
Hiny Hider Headrail Drawings
headrails
1” Aluminum Headrail
Headrail Endcap
Note:
1” headrail with endcap as supplied by Scranton Products. The
headrail has a satin finish.
Integrated into the headrail is a curtain hook track, for which
Scranton Products can provide curtain hooks.
headrails
1” Stainless Steel Headrail Bracket
Note:
Shown is the 1” stainless steel (type 304 -20 gauge) headrail
bracket as supplied by Scranton Products. The bracket has a
satin finish on all exposed surfaces.
Hiny Hider Door Hardware
DOOR HARDWARE
Heavy duty hardware complements
any design option and is available in
anodized aluminum & stainless steel.
Hiny Hider Door Hardware Drawings
LATCH
Universal Emergency Aluminum Slide Latch
Right Hand In
Left Hand In
Note:
Note 1: Shown is the heavy-duty extruded aluminum (6463-T5 alloy) slide latch as supplied by Scranton Products.
The housing of the latch has a bright-dipped anodized finish. The slide bar and button have a black anodized finish.
Note 2: For emergency access on outswing doors, set the latch on the inside of the door at 44 5/8” to the center of the latch,
and approximately 5/8” away from the edge of the door.
STRIKE/KEEPER
6” Inswing Aluminum Strike/Keeper
Note:
Note 1: Shown is the heavy-duty extruded aluminum (6463-T5 alloy) 6” inswing strike/keeper as supplied by Scranton Products.
Note 2: The strike/keeper has a bright dipped anodized finish. The hard rubber bumper is installed in the strike/keeper at the factory.
STRIKE/KEEPER
6” Outswing Aluminum Strike/Keeper
Note:
Note 1: Shown is the heavy-duty extruded aluminum (6463-T5 alloy) 6” outswing strike/keeper as supplied by Scranton Products.
Note 2: The strike/keeper has a bright dipped anodized finish. The hard rubber bumper is installed in the strike/keeper at the factory.
STRIKE/KEEPER
54” & 71” Continuous Aluminum Strike/Keeper
54” Contiunuous Aluminum Strike/Keeper
71” Contiunuous Aluminum Strike/Keeper
LATCH/STRIKE/KEEPER
3” Stainless Steel Emergency Access
Stainless Steel Slide Latch
Stainless Steel In-Swing Strike
Stainless Steel Out-Swing Strike
Note:
Shown is the cast stainless steel (type 304) slide latch as supplied by
Scranton Products. The latch has a satin finish on all exposed surfaces.
door PULL
Chrome Plated Zamak Door Pull
Note:
Shown is the chrome plated zamak door pull as supplied by Scranton Products.
(2 door pulls provided in in-swing and out-swing standard door hardware kits)
COAT HOOK BUMPER
Chrome Plated Zamak Coat Hook Bumper
Note:
Shown is the chrome plated zamak coathook/door stop as supplied by Scranton Products.
WALL STOP
Chrome Plated Zamak Wall Stop
Note:
Shown is the chrome plated zamak wall stop as supplied by Scranton Products.
Hiny Hider Fire Rated Materials
FIRE RATED MATERIALS
Toilet Compartments & Screens | Hiny Hiders® Toilet Partitions |
FIRE RATED BATHROOM PARTITIONS
Scranton Products offers its full product line in a variety of fire rating options. To meet your fire rating need,
simply indicate what fire rating you desire when specifying or quoting the job and the correct fire rated
material will be used.
Scranton Products currently offers standard, Class B, Class A and NFPA286 complaint materials. These are
the relevant fire ratings for our classification of products.
For additional information, contact your Scranton Products representative.
TM
Toilet Compartments & Screens | Hiny Hiders® Toilet Partitions |
FIRE RATING INFORMATION
Hiny Hider Solid Plastic Toilet Partitions
Testing Requirements
FSI
SDI
Class A
<25
0-450
Class B
26-75
0-450
NOTE: NFPA 286 has a pass/fail rating based on established testing criteria and methodology.
Scranton Products Test Results
Flame Spread Index
Smoke Development
Classifications
Class B Solid Plastic Toilet Partitions
60
350
MEETS
CRITERIA
Class A Solid Plastic Toilet Partitions
15
100
MEETS
CRITERIA
NFPA 286 Solid Plastic
Toilet Partitions
PASS
TM
RESISTALL® PARTITIONS
As durable as it is affordable
• Engineered plastic
• Innovative non porous panel design
• Easy installation
• Highly impact resistant
Resistall Case Study
CASE STUDY
MID-SOUTH ICE HOUSE INSTALLS PARTITIONS TO
STAND UP TO HOCKEY, KIDS AND CROWDS
With its humid subtropical climate and the lack of wintry conditions including snow, hockey would seem
a remote interest for the nearly 700,000 residents of Memphis, Tennessee. However, deeply rooted in
this Southeastern city, which ranks as the 20th largest in the United States, is a profound interest in
hockey that extends beyond the Memphis River Kings minor league ice hockey team to the many adult
and junior leagues throughout the region.
Mid-South Ice House
“Several years of planning and research went into the design and construction of this arena,”
says Keith Saunders Sr., owner of Division 10, Inc., a leading provider of construction specialty
products and services throughout Tennessee, and the Southeastern region. “I’ve known one of the
owners personally for 20 years and truly understood his desire to construct a state-of-the-art,
professional skating experience for people who were already traveling to Little Rock or Nashville
to improve their games and forms or just enjoy a skate anytime of year.”
Residents were delighted when their desire to spend more time on the ice was met in September 2011
when the Mid-South Ice House opened to provide the Memphis Metro area with a year-round
opportunity to play hockey, figure skate, take lessons or just enjoy some leisurely ice time during the
city’s latest hot spell. Transformed from an empty warehouse to premier ice skating facility, the Ice
House also features numerous activities such as curling and broomball for all ages.
CASE STUDY
The Mid-South Ice House has continuous activity with minor league hockey,
private leagues and the general public, so Saunders said the facility had to be
built to last and take punishment on almost every level. “We specified the
strongest and most durable materials for use throughout the Ice House,”
explains Saunders. “That particularly included the restrooms, where we
installed Resistall™ Partitions from Scranton Products. We knew we needed
long-lasting toughness and based on my prior experience with the product line,
Resistall was the first and really only choice.”
A leading provider of unique and attractive interior partitions over the past 25
years, Scranton Products offers an assortment of HDPE products in variety of
colors, textures and ADA-compliant configurations. In addition, the company’s
Resistall Partitions are especially designed to never need painting. Unlike
metal partitions which
are subject to rust, they
“We specified the strongest and most
offer superior resistance
durable materials for use throughout the
to dents, scratches,
Ice House,” explains Saunders. “That
graffiti, corrosion, mildew
particularly included the restrooms,
and moisture. Another
where we installed Resistall™ Partitions
benefit is that they are
very easy to clean and
from Scranton Products.”
naturally resistant to
bacteria.
“This arena is my passion,” says Al Austen, co-owner of the Mid-South Ice
House and a general contractor by trade. “I spent years developing this project
and was deeply involved in every aspect of its planning and construction. I’m
proud of what we accomplished and of the ability to provide our local Memphis
residents with an ideal, year-round venue for participating in hockey, figure
skating and all ice-related activities.” Austen adds, “We selected the partitions
from Scranton Products because they fit into this overall vision. They are easy
to maintain and extremely hard to dent as opposed to metal partitions. Plus,
the pricing fit our budget and they do look good. The gray Resistall Partitions
were used in 15 stalls and we haven’t had a problem yet. In fact, I would be
surprised if any arose since I installed several of them myself.”
Resistall Sell Sheet
Resistall™ Partitions
Hybrid
AS DURABLE AS IT
IS AFFORDABLE
(Photo shown with optional additional continuous strikes)
Resistall™ Partitions are fully power washable and steam cleanable,
eliminating the need for harmful chemical cleaners. Because they never
need painting, Resistall™ Partitions deliver no VOC emissions and are
GREENGUARD® Children and Schools Certified. What’s more, they resist
bacteria, odors, moisture and mildew.
NO MOLD GROWTH
Unlike metal partitions which have a cardboard core, Resistall™
Partitions are impermeable to moisture and does not support the
growth of mold and mildew.
NO PAINTING
Resistall™ Partitions are solid color throughout and will not chip so
they never require painting.
CLEANER, HEALTHIER BATHROOMS
When moisture comes in contact with metal, rust begins to form,
becoming a breeding ground for germs.
WE
CALL IT
R E S I S TA L L ™
FOR A
REASON
Hybrid
Resistall™ Partitions stand tough over time
with many features and benefits. Unlike metal
partitions, they are impermeable to moisture
and will never rust or need painting. In
addition, Resistall™ Partitions will not
delaminate and are built to resist mildew,
odors, corrosion and dents, saving you the
added costs of maintenance.
1 Paneled Design
2 Solid Pilasters
This unique aesthetic
style on the doors and
side panels deliver a
premium look and feel.
Front Design
Solid HDPE is used for
the pilasters to ensure
maximum strength at
the anchoring points.
Inside Design
3 Orange Peel Texture
Reduces signs of wear
and deters scratches,
keeping interiors looking
great for years to come.
4 Worry–Free Hardware
To complement any
interior, we offer an
array of great-looking
hardware options.
Color
Black
Grey
Beige
Color matching is limited by printing process.
Actual samples available and are recommended
prior to color selections. All swatches shown in Orange Peel.
801 E Corey Street Scranton, PA 18505 ● 800.445.5148 ● [email protected] ● www.scrantonproducts.com
Resistall Specifications
SPECIFICATIONS
Toilet Compartments & Screens | Resistall® Partitions | Specifications |
SPECIFICATIONS
Section 10 2116
PART 1 - GENERAL
1.1 SUMMARY
A.SectionIncludes:
1.Plastic[toiletcompartments][urinalscreens][privacyscreens][and][entrypartitions].
B.RelatedSections:
1.Division01:Administrative,procedural,andtemporaryworkrequirements.
1.2 REFERENCES
A.ASTMInternational(ASTM):
1.A167-StandardSpecificationforStainlessandHeat-ResistingChromium-NickelSteelPlate,Sheet, andStrip.
2.B221-StandardSpecificationforAluminumandAluminum-AlloyExtrudedBars,Rods,Wire,Profiles, andTubes.
A.CompartmentConfigurations:
1.[Toiletpartitions][privacyscreens]and[entrypartitions]:Floormounted,overheadbraced.
2.Urinalscreens:[Wall][Floor]mounted.
1.4 SUBMITTALS
A.SubmittalsforReview:
1.ShopDrawings:Includedimensionedlayout,elevations,trim,closures,andaccessories.
2.ProductData:Manufacturer’sdescriptivedataforpanels,hardware,andaccessories.
3.Samples:[2x3][__x__]inchsamples[showingavailablecolors.][ineachcolor.]
B.SustainableDesignSubmittals:
1.RecycledContent:Certifypercentagesofpost-consumerandpre-consumerrecycledcontent.
2.RegionalMaterials:CertifydistancebetweenmanufacturerandProjectandbetweenmanufacturer andextractionorharvestpointinmiles.
A.ManufacturerQualifications:Minimum[5][__]yearsexperienceinmanufactureofplastictoiletcompartments
withproductsinsatisfactoryuseundersimilarserviceconditions.
B.InstallerQualifications:Minimum[5][__]yearsexperienceinworkofthisSection.
1.6 WARRANTIES
A.Providemanufacturer’s5yearwarrantyagainstbreakage,corrosion,anddelaminationundernormal
conditions.
PART 2 - PRODUCTS
2.1 MANUFACTURERS
A.ContractDocumentsarebasedonResistallproductsbyScrantonProducts.(www.scrantonproducts.com)
B.Substitutions:[UnderprovisionsofDivision01.][Notpermitted.]
SPECIFICATIONS
Section 10 2116
2.2 MATERIALS
A.DoorsandPanels
1.Constructedoftwosheetsof1/8inchthickhighdensitypolyethylene(HDPE),thermoformedwith
touchpointsintosingleengineeredpanel,withstructuralinsertsontopadmiddlerails.
2.Waterproofandnonabsorbent,withself-lubricatingsurface,resistanttomarksbypens,pencils,
markers,andotherwritinginstruments.
3.Recycledcontent:Minimum[25][__]percent.
4.Color:[____.][Tobeselectedfrommanufacturer’sfullcolorrange.
B.Pilasters
1.SolidPlasticfabricatedfrompolymerresinscompoundedunderhighpressure,formingsingle
thicknesspanel.
2.Waterproofandnonabsorbent,withself-lubricatingsurface,resistanttomarksbypens,pencils,
markers,andotherwritinginstruments.
3.1inchthickwithedgesroundedto1/4inchradius.
C.AluminumExtrusions:ASTMB221,6463-T5alloyandtemper.
D.StainlessSteel:ASTMA167,Type304.
2.3 HARDWARE
A.Hinges:
1.8incheslong,fabricatedfromheavy-dutyextrudedaluminumwithbrightdipanodizedfinish,wrap- aroundflanges,throughboltedtodoorsandpilasterswithstainlesssteel,Torxheadsexbolts.
2.Hingesoperateonfield-adjustablenyloncams,fieldadjustablein30degreeincrements.
B.DoorStrikeandKeeper:
1.6incheslong,fabricatefromheavy-dutyextrudedaluminumwithbrightdipanodizedfinish,secured
topilasterswithstainlesssteeltamperresistantTorxheadsexbolts.
2.Bumper:Extrudedblackvinyl.
C.LatchandHousing:
1.Heavy-dutyextrudedaluminum.
2.Latchhousing:Brightdipanodizedfinish.
3.Slideboltandbutton:Blackanodizedfinish.
D.CoatHook/Bumper:
1.Combinationtype,chromeplatedZamak.
2.Equipoutswinghandicappeddoorswithseconddoorpullanddoorstop.
E.DoorPulls:ChromeplatedZamak.
2.4 COMPONENTS
A.DoorsandDividingPanels:55incheshigh,mounted14inchesabovefinishedfloor.
B.Pilasters:82incheshigh,fastenedto3inchhighpilastersleeveswithstainlesssteeltamperresistantTorxhead
sexbolt.
C.PilasterSleeves:3incheshigh,[one-piecemoldedHDPE,][20gagestainlesssteel,]securedtopilasterwith stainlesssteeltamperresistantTorxheadsexbolt.
D.WallBrackets:54incheslong,[ExtrudedPVC,][heavy-dutyaluminum,1-1/2inchstirruptype,brightdip
anodizedfinish,]fastenedtopilastersandpanelswithstainlesssteeltamperresistantTorxheadsexbolts.
E.Headrail:Heavy-dutyextrudedaluminum,anti-gripdesign,integratedcurtaintrack,clearanodizedfinish,
fastenedtoheadrailbracketwithstainlesssteeltamperresistantTorxheadsexboltandattopofpilaster
withstainlesssteeltamperresistantTorxheadscrews.
TM
SPECIFICATIONS
Section 10 2116
F.HeadrailBrackets:20gagestainlesssteel,satinfinish,securedtowallwithstainlesssteeltamperresistantTorx
headscrews.
PART 3 - EXECUTION
3.1 INSTALLATION
A.Installcompartmentsinaccordancewithmanufacturer’sinstructionsandapprovedShopDrawings.
B.Installrigid,straight,plumb,andlevel.
C.Locatebottomedgeofdoorsandpanels14inchesabovefinishedfloor.
D.Provideuniform,maximum3/8inchverticalclearanceatdoors.
E.NotAcceptable:Evidenceofcutting,drilling,orpatching.
3.2 ADJUSTING
A.Adjustdoorsandlatchestooperatecorrectly.
Vanities
Designed to be worry-free
VANITIES
• Color matched to partitions
• Impervious to moisture
• Never delaminates
• Fully power washable
Vanities Specifications & Drawings
Vanities Specifications
Vanities | Specifications & Drawings |
VANITIES
Solid Plastic Privacy Vanities Specifications - Section 06 6121
PART 1 - GENERAL
1.1 SUMMARY
1. Solid plastic vanities.
1. Division 01: Administrative, procedural, and temporary work requirements..
1.2 REFERENCES
A. ASTM International (ASTM) (www.astm.org):
and Tubes.
1.3 SUBMITTALS
Limiting submittals to only those actually required helps to minimize liability arising from the review of submittals.
Minimize submittals on smaller, less complex projects.
Include the following for submission of shop drawings, product data, and samples for the Architect’s review.
1. Shop Drawings: Include dimensioned layout, elevations, and cutouts for plumbing and accessories.
2. Product Data: Manufacturer’s descriptive data.
Include the following for submission of sustainable design submittals.
The following paragraphs specify minimum level of experience required of the parties performing the work of this
section. Retain if required, and edit to suit project requirements.
A. Manufacturer Qualifications: Minimum [5] [__] years experience in manufacture of solid plastic vanities with
products in satisfactory use under similar service conditions.
1.5 WARRANTIES
A. Provide manufacturer’s 25 year warranty against breakage, corrosion, and delamination under normal
conditions.
PART 2 - PRODUCTS
2.1 MANUFACTURERS
Edit the following to indicate whether or not substitutions will be permitted for the products in this section.
2.2 MATERIALS
A. Solid Plastic Panels:
1. Solid Plastic, fabricated from polymer resins compounded under high pressure, forming single
thickness panel.
VANITIES
Solid Plastic Privacy Vanities Specifications - Section 06 6121
Verify current recycled content with Scranton Products.
Edit the following to suit project requirements.
2.3 COMPONENTS
A. Tops, Splashes, Skirts, and End and Center Supports: 1 inch thick with edges radiused to 1/4 inch.
Edit the following to suit project requirements. Maximum vanity length for single piece is 120 inches.
B. Vanity Size: 24 inches deep x [[__] inches long.] [length indicated on Drawings.]
C. Shoes: 3 inches high, one piece molded HDPE.
D. Attachment Brackets: 16 inches long, heavy duty extruded aluminum with bright dip anodized finish.
PART 3 - EXECUTION
3.1 INSTALLATION
A. Install vanities in accordance with manufacturer’s instructions and approved Shop Drawings.
B. Set plumb, level, rigid, and aligned.
C. Attach vanities to supporting construction with anchors best suited to substrate conditions.
Vanities Drawings
VANITIES
Standard Vanity
FRONT ELEVATION
FRONT ELEVATION
CENTER SUPPORT
END SUPPORT
SIDE ELEVATION
NOTES:
IN CORNER RIGHT
ALL VANITIES ARE MADE OUT OF 1” THICK
MATERIAL (STD.)
NOTES:
1. If the vanity length exceeds 140” please specify where the vanity should be split. The split location is not specified will Scranton products provide a split in the best position to our knowledge.
2. Scranton Products recommends that supports be spaced no greater
than 36” O.C.
IN CORNER LEFT
BETWEEN WALL
FREE STANDING
VANITIES
Standard Vanity With Kickplate
FRONT ELEVATION
FRONT ELEVATION
CENTER SUPPORT
END SUPPORT
SIDE ELEVATION
NOTES:
IN CORNER RIGHT
ALL VANITIES ARE MADE OUT OF 1” THICK
MATERIAL (STD.)
NOTES:
1. If the vanity length exceeds 140” please specify where the vanity should be split. The split location is not specified Scranton Products will provide a split in the best position to our knowledge.
2. Scranton Products recommends that
supports be spaced no greater
than 36” O.C.
IN CORNER LEFT
BETWEEN WALL
FREE STANDING
Shower & Dressing Compartments
Designed to be worry-free
SHOWER & DRESSING COMPARTMENTS
• Impervious to moisture
• Maintenance free solutions
• Never delaminates
• Fully power washable
Shower & Dressing Compartments Specifications & Drawings
Shower & Dressing Compartments Specifications
Shower & Dressing Compartments | Specifications & Drawings |
Solid Plastic Shower & Dressing Compartments Specifications - Section 10 2119
PART 1 - GENERAL
1.1 SUMMARY
1. Solid plastic [shower] [and] [dressing] compartments.
1.2 REFERENCES
and Tubes.
B. National Fire Protection Association (NFPA) 286 - Standard Methods of Fire Tests for Evaluating Contribution of
Wall and Ceiling Interior Finish to Room Fire Growth.
1.3 SUBMITTALS
A. Manufacturer Qualifications: Minimum [5] [__] years experience in manufacture of solid plastic shower and
dressing compartments with products in satisfactory use under similar service conditions.
1.5 WARRANTIES
A. Provide manufacturer’s 25 year warranty against breakage, corrosion, and delamination under normal
conditions.
PART 2 - PRODUCTS
2.1 MANUFACTURERS
Solid Plastic Shower & Dressing Compartments Specifications - Section 10 2119
2.2 MATERIALS
thickness panel.
3. 1 inch thick with radiused edges.
**** OR ****
**** OR ****
C. Shower Curtains: Vinyl, 42 inches wide x 72 inches high, hung with aluminum curtain hooks with selflubricating Delrin slides.
2.3 COMPONENTS
A. Panels: 76 inches high, mounted to pilasters with continuous brackets and to panels with continuous extruded
aluminum brackets or continuous extruded aluminum shower corner brackets.
B. Pilasters: 82 inches high, fastened to panels with continuous brackets.
C. Headrail: Heavy-duty extruded aluminum, anti-grip design, clear anodized finish, fastened to headrail
brackets and top of pilaster using stainless steel tamper-resistant Torx head screws.
D. Headrail Brackets: 20 gage stainless steel, secured using stainless steel tamper-resistant Torx head screws.
E. Brackets: 76 inches long, extruded aluminum, clear anodized finish, attached using stainless steel tamperresistant Torx head screws.
PART 3 - EXECUTION
3.1 INSTALLATION
C. Not Acceptable: Evidence of cutting, drilling, or patching.
Shower & Dressing Compartments Drawings
8” Aluminum Wrap Around Hinge Continuous Aluminum Brackets With Door and Seat
STD FRONT ELEVATION
STD SIDE ELEVATION
Notes:
1. Upon approval of these drawings, this order shall be scheduled for fabrication.
2. where pilasters and panels meet there is a 1/2” space.
3. where pilasters and/or panels meet a wall there is a 1” space.
4. headrail shall be cut 2” longer than the overall dimension and cut to size in the field by the installer.
Continuous Aluminum Brackets Without Doors Shown With Seat
Notes:
• Headrail can be used as a shower curtain rod
• Shower Curtains will only be supplied if they were quoted
STD FRONT ELEVATION
STD SIDE ELEVATION
Notes:
Continuous Aluminum Brackets Shown Without Doors - Wide Pilaster
Notes:
STD FRONT ELEVATION
STD SIDE ELEVATION
Notes:
Continuous Aluminum Brackets Without Doors - Narrow Pilaster
Notes:
STD FRONT SHOWER ELEVATION
STD SIDE ELEVATION
Notes:
2. Where pilasters and panels meet there is a 1/2” space.
3. Where pilasters and/or panels meet a wall there is a 1” space.
4. headrail shall be cut 2” longer than the overall dimension,
and cut to size in the field by the installer.
FLOOR TO CEILING
8” Aluminum Wrap Around Hinge Continuous Aluminum Brackets With Door and Seat
Notes:
• FLOOR TO CEILING
• CONTINUOUS BRACKETS
• 8” ALUMINUM WRAP AROUND HINGE
STD FRONT ELEVATION
STD SIDE ELEVATION
Notes:
FLOOR TO CEILING
Continuous Aluminum Brackets Without Doors Shown With Seat
Notes:
• FLOOR TO CEILING
• CONTINUOUS BRACKETS
STD FRONT ELEVATION
STD SIDE ELEVATION
Notes:
FLOOR TO CEILING
Continuous Aluminum Brackets Without Doors - Wide Pilaster
Notes:
1. no shower hooks will supplied unless specified for all shower compartment openings. shower curtains will be supplied only when quoted with the order.
STD FRONT ELEVATION
STD SIDE ELEVATION
Notes:
FLOOR TO CEILING
Continuous Aluminum Brackets With Doors - Narrow Pilaster
Notes:
STD FRONT ELEVATION
STD SIDE ELEVATION
Notes:
SEATS
Seat Standard Configuration
PLAN ELEVATION
NOTES:
STD SHOWER SEAT ELEVATION
SEAT SUPPORT
1. Seats/Shelves are made of 1” plastic.
2. 4” L Brackets will be supplied for seat attachments.
3. Use 3/4” Torx screws at all plastic connections & 1 1/2” w/ anchors at wall
4. Shower seat/shelves length will be the exact clear dimension. If needed, cut in the field to fit & notch around brackets unless otherwise noted on shop drawing.
“L” BRACKET
SEATS
Seat With End Support
PLAN ELEVATION
NOTES:
STD SHOWER SEAT ELEVATION
SEAT SUPPORT
“L” BRACKET
SHELF
Shelf Standard Configuration
STD. SHOWER SHELF ELEVATION
PLASTIC SUPPORT
“L” BRACKET
NOTES:
NOTES:
1. Doors large than 30” are to be set to the closed position.
4. Headrail shall be cut 2” longer than the overall dimension, and cut to size in the field by the installer.
Lockers
Where solid construction meets rigid good looks
LOCKERS
• Maintenance Free
• Impact & Dent Resistant
• Graffiti Resistant
• Will never rust corrode
or delaminate
Tufftec Lockers
TUFFTEC LOCKERS®
Locker solutions for every place and purpose
• Customizable
• Solid classic construction
• Versatile configurations & storage solutions
• Industry leading 25 year warranty
Tufftec Lockers Case Study
CASE STUDY
Collins Sports & Fitness Center Installs Lockers
For A Tough Crowd
The Collins Perley Sports & Fitness Center in St. Albans, VT, is owned by the local public high school and
was built in the mid 1980s as their primary athletic and physical education facility. It is run as both a
school and community facility with more than 25 high school sports teams, 12 daily physical education
classes and a semi-pro soccer team. In the past few months, the center has been renovating its locker
room and restroom facilities, where the traditional metal was taking some abuse.
Most of the center’s public use is fee-based and is critical to the center’s financial stability, though keeping
costs low is also important to its community image. According to Dave Kimel, facility manager, the center
has been slowly renovating a few rooms at a time, as funds have allowed.
“We shopped hard for our locker and restroom products, comparing quality, price and reputation
for service and Scranton Products stood out above the rest,” said Kimel. “They were the most
highly recommended by the best installation company we could find in the state of Vermont.”
Collins Perley Sports & Fitness
Center Tufftec Hunter Green
Lockers
The center gets about 600,000 user visits to its facility each year, about 400,000 of which are unrelated to
school functions. “That's a lot of swinging and banging on toilet stall doors and slamming of locker room
doors, said Kimel, “so wear and tear is important.” He said most of the old metal lockers still worked but
they looked old and got absolutely no respect from the school kids. “We had constant problems with
scratching and graffiti,” said Kimel. “Since we put these new Tufftec® lockers in we have not had a single
incident of damage.”
www.scrantonproducts..com ● 800.445.5148 ● [email protected]
CASE STUDY
Considering the traffic Collins Perley endures, the lockers and stalls needed to
be high quality and extremely durable. “One of the key reasons for choosing
Scranton Products’ shower partition and locker products was the overall
value,” said Kimel. “We're a public high school and money is tight but a good
product is not the cheapest, it’s the best value and performance over time,” he
said. “The facility amenities also have to look great--the better they look the
more memberships we'll sell and the more our kids will respect and take care
of our facility.”
Kimel said another important feature for the locker rooms is sanitation, with
one locker having three or four different users per day. “In a public facility there
is nothing more important that cleanliness,” he explained. “These HDPE
lockers and partitions have no cracks, crevices, or edges to catch cleaning
cloths or trap mold, mildew, and other bacteria and they’re easy to clean.” He
also finds they pay off from a lifecycle perspective and after three years for
some of the shower and locker products, they all look as good as the day they
were installed. “Every
hinge, every latch, every
“These HDPE lockers and partitions
hanger works as well today
as it did three years ago,”
have no cracks, crevices, or edges to
he said, “so we’ll continue
catch cleaning cloths or trap mold,
to have more installed.”
mildew, and other bacteria and
they’re easy to clean,” said Kimel.
He noted that back in the
80s, gang showers were
fine for most high school
gym classes. But with the
multi-use facility, Kimel has seen that change with more demands for privacy.
“Scranton Products came up with a simple, clean, great looking, and
inexpensive way to convert one side of our gang showers to individual
showers at very low cost,” he said. “And my crew finds them very easy to
clean."
Along with serving as the home for numerous sports teams, the center has
seen a significant increase in paid memberships over the past three years.
“We attribute that in large part to the way our locker rooms now look and feel;
they are the customers' first and last impression of their visits here.” According
to Kimel, if you compare a sports and health facility to a house tour, the locker
room is as important as a kitchen or bathroom--the two most important rooms
when appraising value. “I can get by with an older model treadmill but I better
not have rusted lockers," he said.
Tufftec Lockers Specifications & Drawings
Tufftec Lockers Specifications
Tufftec Lockers® | Specifications & Drawings
TUFFTEC LOCKERS®
Solid Plastic Lockers Specifications - Section 10 5126
PART 1 - GENERAL
1.1
SUMMARY
1. Solid plastic lockers.
2. Locker benches.
1.2 SUBMITTALS
A. Manufacturer Qualifications: Minimum [5] [__] years experience in manufacture of solid plastic lockers with
1.4 WARRANTIES
normal conditions.
PART 2 - PRODUCTS
2.1 MANUFACTURERS
2.2 MATERIALS
1. Lockers:
a. Solid plastic formed under high pressure into solid plastic components with homogeneous
color throughout, with smooth orange peel finish.
b. Edges machined to accept assembly brackets.
2. Locker benches:
a. Solid plastic fabricated from polymer resins compounded under high pressure, forming
single thickness panel.
b. Waterproof and nonabsorbent, with self-lubricating surface, resistant to marks by pens,
pencils, markers, and other writing instruments.
TUFFTEC LOCKERS®
2.3 COMPONENTS - LOCKERS
A. Locker Doors and Frames: 1/2 inch thick.
B. Sides, Tops, Bottoms, Backs, and Shelves: 3/8 inch thick.
C. Latch: Continuous type, manufactured from HDPE, capable of accepting various locking mechanisms, fastened
to entire length of door.
D. Door Hinge: Heavy duty extruded aluminum, full length, assembled onto door and locker front.
E. Assembly Profile: Full height of lockers, PVC plastic, snap fit assembled onto locker sides.
F. Coat Hooks: Two-prong, high impact plastic, mounted to bottom of shelf or divider, one per door opening.
2.4 COMPONENTS - LOCKER BENCHES
A. Bench Tops: 1-1/2 inch thick with edges rounded to 1/4 inch radius, 9-1/2 inches wide x [[__] inches long.]
[lengths indicated.]
B. Pedestals: [Steel, 16-1/4 inches high,] [Aluminum, 16 inches high,] secured to tops with stainless steel tamper
resistant Torx head screws and to floor with lead expansion shields and 2 inch long stainless steel machine bolts.
2.5 FABRICATION
A. Fabricate locker components square and rigid, finish free from scratches and chips.
B. Fabricate locker components for snap-together assembly or slide-together dovetail conections providing solid
and secure, anti-racking construction.
C. Fabricate adjacent lockers with common side panel.
D. Fabricate locker units for assembly in maximum of three adjacent lockers.
E. Fabricate locker benches to sizes indicated in single lengths.
PART 3 EXECUTION
3.1 INSTALLATION
A. Install lockers in accordance with manufacturer’s instructions and approved Shop Drawings.
B. [Set lockers directly on floor.] [Set lockers on prepared locker base.]
C. Set plumb, level, rigid, and aligned.
D. Attach lockers to supporting construction with anchors best suited to substrate conditions.
E. Attach locker benches to floor.
3.2 ADJUSTING
TM
Tufftec Lockers Drawings
TIERS & DOORS OPTIONS
TIERS
1-6 Tiers
DOOR VENTING OPTIONS
Horizontal
Lattice Mesh Full Full
Lattice
Full
Full
Full
Mesh
Horizontal
Horizontal
Horizontal
Lattice Lattice
Mesh
Lattice
Mesh
Mesh
Lattice
Lattice
Lattice
Mesh
Mesh
Horizontal
Lattice
Mesh Mesh
Lattice
Mesh
1 - 6 Tier
NOTES:
1. Most lockers are available in banks
of 1, 2, and 3.
SPECIALTY STYLE OPTIONS
Z-Locker
Athletic
(open locker no door)
Z Locker
Utility
Cubbies
Custom Configurations are available.
FullFull
Lattice Full
Full
Full
Mesh Side
Lattice
Mesh
Lattice
Lattice
Mesh
Mesh
Lattice
Mesh
Venting
Side Venting
Side
Side
Venting
Venting
Side
Venting
SPECIALTY STYLE OPTIONS
Bases, Fillers, Hooks, Handles, Hinges, Locks and Tops
TOPS
Slope
LOCKER BASE
4” high black base, 1” thick.
Bases are assembled in the
field
Flat
HANDLE
FILLERS
LOCK OPTIONS
Ergonomic handle,
designed to
meet ADA code
compliance
4”, 8”, 12”, 18” widths
Tufftec Locker® systems
support a variety of locking
options, including:
72” height
Padlock
ENGRAVING
Key
Digi Lock In-Door
Combination
Lock
ADA COMPLIANCE PACKAGE
HOOKS
Metal j-hook
Coin Key
Double-prong
black coat hook
ADA compliant
conversion kits available
with ADA plaques,
adjustable shelves
and clips.
Custom engraving of
GarmentDouble
Bar Hook
Single Prong
Hook
Prong Hook Double Prong Hook
team logos
and otherSingle Prong
symbols available in
one-color or two-color
options.
PLASTIC BENCHES
HINGE
1 1/2” thick plastic
benches to match
color locker
selections.
Heavy duty extruded
aluminum with corrosionfree stainless steel pin for
years of superior corrosion
free performance.
Available in silver
and black.
TM
Tufftec Benches
TUFFTEC BENCHES
TM
Locker solutions for every place and purpose
• Built from 1 1/2” solid plastic
• Color matched to your lockers
• Versatile configurations
• Extremely durable
Tufftec Benches Specifications & Drawings
Tufftec Benches Specifications
TufftecTM Benches |
TUFFTEC LOCKERS® & BENCHES
PART 1 - GENERAL
1.1 SUMMARY
2. Locker benches.
1.2 SUBMITTALS
1.4 WARRANTIES
normal conditions.
PART 2 - PRODUCTS
2.1 MANUFACTURERS
2.2 MATERIALS
1. Lockers:
a. Solid plastic formed under high pressure into solid plastic components with homogeneous
color throughout, with smooth orange peel finish.
b. Edges machined to accept assembly brackets.
2. Locker benches:
a. Solid plastic fabricated from polymer resins compounded under high pressure, forming
single thickness panel.
b. Waterproof and nonabsorbent, with self-lubricating surface, resistant to marks by pens,
pencils, markers, and other writing instruments.
TufftecTM Benches |
TUFFTEC LOCKERS® & BENCHES
2.3 COMPONENTS - LOCKERS
A. Locker Doors and Frames: 1/2 inch thick.
D. Door Hinge: Heavy duty extruded aluminum, full length, assembled onto door and locker front.
E. Assembly Profile: Full height of lockers, PVC plastic, snap fit assembled onto locker sides.
2.4 COMPONENTS - LOCKER BENCHES
A. Bench Tops: 1-1/2 inch thick with edges rounded to 1/4 inch radius, 9-1/2 inches wide x [[__] inches long.]
[lengths indicated.]
B. Pedestals: [Steel, 16-1/4 inches high,] [Aluminum, 16 inches high,] secured to tops with stainless steel tamper
resistant Torx head screws and to floor with lead expansion shields and 2 inch long stainless steel machine bolts.
2.5 FABRICATION
E. Fabricate locker benches to sizes indicated in single lengths.
PART 3 - EXECUTION
3.1 INSTALLATION
E. Attach locker benches to floor.
3.2 ADJUSTING
TM
Tufftec Benches Drawings
TufftecTM Benches | Specifications & Drawings
TUFFTECTM DRAWINGS
Benches
PLAN VIEW
ELEVATION
ALUMINUM
STEEL
Duralife Lockers
DURALIFE LOCKERS
TM
Built for the long hall
• NFPA 286 fire rating compliant
• Competitively priced
• Recessed handle
• 15 Year Warranty
Duralife Lockers Case Study
CASE STUDY
Duralife Lockers Provided Solution for
Ocean City High School
PHOTO HERE
Located near the shore in Ocean City, NJ, Ocean City High School wanted to avoid all the maintenance issues
associates with corrosion, when building their new school. In the 7 years since the lockers were installed,
there have been no reports of locker break-ins, no doors have required replacements, there has been no
noticeable scratching, and graffiti can be quickly and easily wiped off.
Job Photo Here
Robert Gannon
Director of Facilities
at Ocean City High School
in New Jersey
“Maintaining metal lockers was a nightmare. With plastic lockers, we cut our maintenance
time from 3-4 weeks to just 2-3 days, and cleaning graffiti from days to minutes. I couldn’t
be happier,” said Robert Gannon, Director of Facilities at Ocean City High School in New Jersey.
Scranton Products premium brands have led the HDPE plastic market, setting new benchmarks for the
industry for quality and innovation. Together, the brands of Scranton Products offer the most comprehensive
and trusted line of products in the industry. Scranton Products boasts more than 28 years of experience in
designing products – lockers, bathroom partitions, shower stalls and dressing compartments. In comparison
to other locker options for hallway corridors, Duralife lockers have shown to be the most durable, lowmaintenance in the industry. These inventive options are designed to be worry-free and are built to last. Duralife lockers have proven to withstand the test of time – especially with school age children.
Duralife Lockers Specifications & Drawings
Duralife Lockers Specifications
Duralife LockersTM | Specifications & Drawings |
DURALIFE LOCKERSTM
PART 1 - GENERAL
1.1 SUMMARY
1.2 REFERENCES
A. National Fire Protection Association (NFPA) 286 - Standard Methods of Fire Tests for Evaluating Contribution of
Wall and Ceiling Interior Finish to Room Fire Growth.
1.3 SUBMITTALS
1.5 WARRANTIES
normal conditions.
PART 2 - PRODUCTS
2.1 MANUFACTURERS
2.2 MATERIALS
1. Sold Plastc formed under high pressure into solid plastic components with homogeneous color
throughout, with smooth orange peel finish.
2. Edges machined to accept assembly brackets.
TM
DURALIFE LOCKERSTM
2.3 COMPONENTS
A. Locker Doors: 1/2 inch thick.
D. Door Hinge: Heavy duty zinc-plated steel, full length, assembled onto door and locker front.
E. Assembly: Tongue-and-groove joint construction using 3/8 inch thick HDPE, full height of locker.
2.4 FABRICATION
PART 3 - EXECUTION
3.1 INSTALLATION
3.2 ADJUSTING
TM
Duralife Lockers Drawings
DESIGN OPTIONS
FLAT TOP
1 Continuous strike
Fully integrated ½” thick
HDPE 6-point strike for
improved locking
performance and security
2 Latch
6-point push-to-close
latch made of extremely
durable HDPE
3 Lock
Fully compatible with most
standard and recessed
combination locks
TRIM
4 Door
Full-height solid HDPE
door with standard
ventilation
SLOPE TOP
5
3
5 Frame
Solid HDPE tongue and
groove construction with
corrosion resistant
mechanical fasteners
2
1
4
6 Hinge
Full-height anodized steel
piano hinge
6
TM
STANDARD & OPTIONAL DESIGN OPTIONS
STANDARD OFFERINGS
VENTING
SHELF
COAT HOOK
HINGE
Arc venting for
improved styling
Plastic shelf
located 12” from
the top (standard
with 1 Tier locker)
Metal j-hook
Silver anodized steel
continuous hinge
TIERS
DIMENSIONS
One or Two
Width 12”, 15”
Depth 12”, 15”, 18”
Height 60”, 72”
Single Prong Hook
Double Prong H
NOTES:
1. Most lockers are available in banks
of 1, 2, and 3.
OPTIONAL OFFERINGS
LOCKS
TOPS & TRIM
FILLERS
LOCKER BASE
#1 Combo
Slope
4”, 8”, 12”, 18” widths
4” high black base, 1” thick.
Bases are assembled in the
field
Hasp
Flat
72” height
Trim
COAT HOOK
Double-prong
black coat hook
Double Prong Hook
TM
Duralife Lockers Fire Rated Materials
FIRE RATED MATERIALS
Duralife LockersTM | Fire Rated Materials |
FIRE RATED DURALIFE LOCKERSTM
Scranton Products offers its full product line in a variety of fire rating options. To meet your fire rating need,
simply indicate what fire rating you desire when specifying or quoting the job and the correct fire rated
material will be used.
Scranton Products currently offers standard, Class B, Class A and NFPA286 complaint materials. These are the
relevant fire ratings for our classification of products.
For additional information, contact your Scranton Products representative.
TM
Scranton Products Contact Information
General Information |
SCRANTON PRODUCTS®
Contact Information
Contact Information
801 E. Corey Street
Scranton, PA 18505
800.445.5148
Fax: 800.551.6993
[email protected]
scrantonproducts.com
TM

Architectural Binder

Transcription

Similar documents

hafeilobopartsmanual

Series 70 ePODs: Type-P

PERSPECTIVE VIEWS OF OBJECTS

From: Chris Arden [mailto:[email protected]

2 - Lakeland College

mis–architecture mis-architecture.co.uk

MASTER DRAWINGS Jason McCoy Gallery is pleased to present

AroundAboutTown.com Floorplan

2013 Summer Courses

Step Stool - The Exhibitors` Handbook