KARCTUFOMNA Micro Remote Control UFO

Micro Remote Control UFO Quadcopter
KARCTUFOMNA
Quick Start Guide
Please read this guide carefully before use.
Product Layout
Battery Installation
To load the batteries:
Open the battery cover on the back of the
transmitter, then load 6 x AA batteries
correctly as shown by the polarity
markings.
CAUTION
•
•
•
Make sure the battery polarities are
correct. Do not load batteries upsidedown.
Please do not mix old and new
batteries.
Please do not mix batteries of different
types.
Charging Aircraft Battery
Please remove the lithium battery from the aircraft as shown, disconnecting the power
plug. Plug the USB charger into the power plug, and the LED lights will illuminate to
show that the battery is receiving charge. The LED lights should go out after approx. 45
minutes, at which point the battery is fully charged.
1
Lithium Battery Notes
•
•
•
In the event of misuse, the batteries may catch fire, leak or explode. The user
should be aware of the risks of using batteries. Kogan.com do not bear any
responsibility for accidents that occur through misuse or accidents.
If during use of during charging you notice smoke or a strange smell, unplug the
cord immediately.
Please follow these instructions.
Lithium Battery Charging
•
•
•
•
•
Please use the original supplied charger to ensure your safety.
Do not charge damaged or worn out batteries.
Do not overcharge your batteries. Once the charging LEDs go out, please unplug
the charging cord.
Do not charge the batteries next to flammable gases, liquids or objects.
If the batteries become hot to the touch during use or charging, immediately
stop charging or use.
Use and Storage
•
•
•
•
•
•
•
•
•
•
Do not insert or remove batteries while product is in use.
Do not use damaged batteries.
Do not expose the batteries to rain, excessive heat or sudden impacts.
Do not allow children or babies to play with the batteries.
Do not throw batteries into a fire.
Do not dismantle, drill or cut the batteries.
Do not clean charger with alcohol or any flammable solvents.
Do not attempt to short circuit the batteries or charger.
Please store product at room temperature.
Please remove the batteries from the unit if unit is not being used for an
extended period of time.
Disposal
•
At the end of it's useful life, do not dispose of the batteries with the household
waste. The batteries should be recycled as per your local municipal recycling
operations.
2
Use and Control
1.
The aircraft power cord and the battery cord
should be connected as shown on page 1. Correct
these together while the helicopter is sitting on flat
ground.
2. After about 6 seconds, the LED lights will be
flashing. To pair the controller and the helicopter,
push the throttle stick to the bottom, then turn the
power switch to ON. Immediately push the throttle
stick up to the maximum, then back down to the
bottom. Upon completion of these steps, the
aircraft can be operated.
IMPORTANT: The white blades should be on the front side of the copter, while the black
blades should be on the rear side.
Push the throttle up, and the
speed of the blades will
increase. The copter will begin
to ascend.
Pull the throttle back, and the
speed of the blades will
decrease. The copter will
begin to descend.
Push the rudder stick to the
left, and the copter will turn
left.
Push the rudder stick to the
right, and the copter will turn
right.
When the rudder stick is
pressed upward, the copter
will tilt and move forward.
When the rudder stick is
pulled back, the copter will
tilt back and reverse.
When the rudder is pressed
to the right, the copter will
fly to the right.
When the rudder is pressed
to the left, the copter will fly
to the left.
Push the controls slowly to ensure you have adequate control of the copter.
3
Note: once the copter ascends to a height of 30cm or above, it will suffer from the
"ground effect" and the performance will become unstable. With practice you will be
able to control this.
When the copter continually spins to the left, please
press the right trimming button until it stops spinning.
When the copter continually spins to the right, please
press the left trimming button until it stops spinning.
When the copter flies sideways
(towards the left) in the process
of hovering, please press the
right-hover trimming button
until it stops.
When the copter flies sideways
(towards the right) in the
process of hovering, please
press the left-hover trimming
button until it stops.
When the copter flies
backwards in the process of
hovering, please press the
forward-hover trimming button
until it stops.
When the copter flies forwards
in the process of hovering,
please press the backwardhovering trimming button until
it stops.
Press and hold the speed conversion button while turning
on the power switch. This will reset the trim settings.
4
If the copter is not easily controllable, this may require a
full reset of the controller so that it can be recalibrated.
Press both joysticks back and to the left, then press the
throttle lever. The lights on the copter will flash, at which
point you should release all of the controls. The
controller will then be recalibrated to the copter.
Flying Environment
•
•
•
•
Indoor flying: choose a wide, spacious location with no barriers, pets or people.
Outdoor flying: choose a warm, sunny and windless day.
Do not fly in extreme temperatures. Flying in extreme temperatures may affect
the performance and lead to damage to the product.
Do not fly in windy weather. The performance and control of the copter will be
affected by winds. Windy conditions may cause loss of control which will
damage the copter.
Flying Practice
To master the copter, please attempt the following practices before attempting any
skilled flight patterns.
Fixed-point revolving
Square pattern flight
Cross-action flight
Fixed-point landing
When you can perform a take-off, rotation and return landing to the point of take off,
you can then attempt square and cross pattern flight actions.
3D Flip Flying
Users can control the copter to perform some breathtaking operations when mastering
the basics. First, fly the copter up to a height of 3m. Then press the flip button and push
the right rudder to one direction, then release it. The copter will flip over.
5
Problems and Solutions
Problem
Transmitter not working
Control failure
Take-off failure
Landing too soon
Out of control
Cause
Solution
Transmitter is OFF
Turn transmitter ON
Batteries not installed correctly
Reinstall batteries, paying attention to
the polarity markings
Batteries are flat
Replace batteries
Transmitter is OFF
Turn transmitter ON
Copter battery is disconnected
Reconnect the battery cables
Wind is too strong
Do not fly the copter during extremely
windy weather
Rotation of blades is too slow
Push the throttle stick upwards
Copter battery is flat
Recharge the copter battery
Throttle stick was pulled back too fast
Pull the throttle stick back slowly to
perform a smooth landing
Beyond the effective control distance
Ensure that there are no other
transmitters within 30m that are using
the same frequency, and ensure you
are within 30m of the copter while
controlling it.
Precautions
•
•
•
•
The remote controlled distance will be shorter when the batteries in the copter
or the controller themselves are low.
It will be difficult to take off when the batteries are low.
If the copter is damaged, please stop using it immediately.
If you will not be using the transmitter for a long time, please remove the
batteries to avoid leakage.
6