22 to .50 caliber laser bore sighter .22 to .50 caliber laser bore sighter

Su
®
.22 TO .50 CALIBER
LASER BORE SIGHTER
By projecting a laser from the center of the axis of the barrel of your
firearm, the LaserLyte Laser Bore Sighter allows you to instantly and
accurately set your sight or scope. The easy-to-use system works with
all .22-.50 caliber rifles and pistols.
Experience the confidence of an accurate sight or scope wherever
you are, by using the Laser Bore Sighter to quickly check alignment,
especially after a long trip to a hunting location.
pe
Br
.22 TO .50 CALIBER
LASER BORE SIGHTER
ig
ht
For Handguns and Rifles
Scopes and Sights
Easy to Use
SCOPE AND SIGHT ALIGNMENT HAS NEVER
BEEN EASIER OR MORE ACCURATE!
made in
U.S.A.
2.25
2.00
1.75
1.50
1.25
1.00
.75
.50
.25
NO MORE WASTED TIME!
NO MORE WASTED AMMO!
• < 5mw Class IIIa Laser
• 4 bore adjustable adapters to fit all .22-.50 caliber pistols and rifles
• One year limited warranty
PA R T S I N C L U D E D
Nylon Case
Laser Bore
4 Adjustable Adapters
*u
se
rif tar
le ge
or t t
ha o s
nd ite
gu in
n
w w w . l a s e rl y t e .c o m
r-
DANGER
LASER LIGHT
AVOID DIRECT EYE EXPOSURE
POWER OUTPUT <5mw
WAVELENGTH 630-670nm
CLASS IIIa PRODUCT
BAK-55NC-140
U.S. Patent No. 6, 421,947
®
Comes Complete—Ready to Use
w w w .l a s e r l y t e . c o m
Laser Accuracy to 4" at 100 yds.
LASER BORE
ALIGNMENT K I T
Operating the Laser Bore Alignment Tool
The unit comes packaged with batteries installed. To turn the laser on,
first make sure it is pointing away from your eyes or anyone else, rotate
the switch a half turn in either direction until you feel a click and the laser
is on. To turn the laser off, rotate the switch another half turn.
BAK-55NC-140
Each Universal Laser Bore Sighter comes with 4
bore adapters to fit any .22 to .50 caliber firearm.
This unit installs in the barrel of the firearm and
projects a laser beam from the center of the axis
of the bore. This allows the accurate bore alignment of scopes, iron sights or lasersights on
handgun or rifles.
.435 to .500 cal.
.350 to .434 cal.
DANGER
LASER LIGHT
The laser operates on (3) # A76 batteries which are very common
watch/calculator batteries. Many manufacturers make them under different numbers such as LR-44, AG13 etc. These 3 batteries will operate this
unit for over 1 hour continuos, however used for just a few minutes at a
time, many firearms may be bore sighted before replacement.
To replace batteries, turn the Switch/Battery Holder to the on position.
Push switch forward (toward the laser end) slightly and lift out from rear
(as shown below).
.280 to .349 cal.
AVOID DIRECT EYE EXPOSURE
POWER OUTPUT <5mw
WAVELENGTH 630-670nm
CLASS IIIa PRODUCT
Switch and
Battery Holder
.220 to .270 cal.
Laser Bore
Alignment Tool
Bore Adapters
NOTICE: DO NOT ADJUST THESE SCREWS!
These (4) screws are set at the factory when aligning.
Movement of them will void your warranty.
The intended use is for indoors or outdoors in subdued sunlight.
Use of the Laser BoreSighter
First install the 4 screws into the 4 adapters supplied (2 longer screws in
the larger adapters and 2 shorter screws in the 2 smaller adapters).
MAKE SURE FIREARM IS UNLOADED
BEFORE PROCEEDING!
Select the proper adapter for the caliber of the firearm and thread onto the
back of the Laser Bore Alignment Tool (as shown above). The adapter
expands larger as you turn it onto the Laser Bore Alignment Tool (as
shown below).
Each Adapter Expands To Fit Its Range Of Calibers
Aligning Your Sight
The laser light emitted form the Laser Bore Tool travels in a straight line
while the bullet fired follows a trajectory. Even though the use of this
device will get you very close, final adjustment should be made at the
range.
For Scoped Firearms:
If you have the ability to bore sight your scope at 50-100 yard, (indoor
shooting range, outside in subdued sunlight - evening or early morning)
then no compensation for the offset of the scope and barrel will be necessary, just adjust your crosshairs to correspond with the laser dot.
Shorter distances such as 25-50 feet will need to be compensated for by
measuring the approximate distance between the center of your barrel
and the center of your scope. Using the target on the front of this packaging, place the laser dot on the center of the target and adjust the
crosshairs to match that distance above the center of the target.
For Iron Sight Firearms:
Adjust the sights to place the projected laser dot on top of the front sight
blade. The distance for sighting-in iron sights is not near as critical, however the greater the distance the greater the accuracy.
For information on other great products from LaserLyte check out our web-site at
www.LaserLyteSights.com or call us at 928-649-3201.
Adjust the adapter for a snug fit into the barrel and slide in to the large
taper on the Laser Bore Alignment Tool. This has now aligned it with the
center of the axis of the bore.
101 Airpark Rd./ P.O. Box 126 - Cottonwood, AZ 86326
Phone 928-649-3201 - Fax 928-649-3970