user manual

Transcription

user manual

USER'S MANUAL
FLOOR & CEILING
SERIES
ASF-60AN
CONTENTS
3
It is not good for your health to expose your body to the
air flow for a long time.
PAGE
Do not insert fingers, rods or other objects into the air
inlet or outlet.
When the fan is rotating at high speed, it will cause injury.
IMPORTANT SAFETY INFORMATION........................................................1
INDOOR UNIT
TEMPORARY OPERATIONS.....................................................................2
AIR CONDITIONER OPERATIONS AND PERFORMANCE............................3
HINTS FOR ECONOMICAL OPERATION.....................................................4
1
ADJUSTING AIR FLOW DIRECTION..........................................................4
4
AU
TO
CO
OL
DR
AT
FOLLOWING SYMPTOMS ARE NOT AIR CONDITIONER
TROUBLES..........5
CLOC
K
SET
FAN
DE
HOU
R
SPEE
D
FAN
SPE
ED
SW
SW
AIR
RESE
T LOCK
ING
ING
C/H
DIRE
CTIO
TIM
TIM
OWNER'S
N
OK
ECO
CLO
TROUBLESHOOTING.................................................................................6
6
TEM
SE P
T
Y
HE
FAN
MO
M
MAINTENANCE.........................................................................................4
2
8
After a long use, check the unit stand and fitting for
damage.
If damaged, the unit may fall and result in injury.
Never put any objects into the air inlet or outlet.
Objects touching the fan at high speed can be dangerous.
To avoid oxygen deficiency, ventilate the room
sufficiently if equipment with burner is used together
with the air conditioner.
1. IMPORTANT SAFETY INFORMATION
To prevent injury to the user or other people and property
damage, the following instructions must be followed. Incorrect
operation due to ignoring of instructions may cause harm or
damage.
9
The safety precautions listed are divided into two categories. In either
case, important safety information is listed which must be read.
OR
Failure to observe a warning may result in death. The
appliance shall be installed in accordance with national
wiring regulations.
9
7
8
CAUTION
7
8
Failure to observe a caution may result in injury or damage
to the equipment.
9
WARNING
Ask your dealer for installation of the air conditioner.
Incomplete installation performed by yourself may result in a
water leakage, electric shock, and fire.
8
8
8
INDOOR UNIT
Fig.1
OUTDOOR UNIT
7
8
9
Air flow louver (at air outlet)
Air inlet (with air filter in it)
Installation part
Connecting pipe
Air inlet
Air outlet
Display panel
Ask your dealer for improvement, repair, and
maintenance.
Incomplete improvement, repair, and maintenance may result
in a water leakage, electric shock, and fire.
In order to avoid electric shock, fire or injury, or if you
detect any abnormality such as smell of fire, turn off the
power supply and call your dealer for instructions.
Never let the indoor unit or the remote controller get wet.
It may cause an electric shock or a fire.
Never press the button of the remote controller with a
hard, pointed object.
The remote controller may be damaged.
Remote controller
Drain pipe
NOTE
All the pictures in this manual are for explanation purpose only. They may be slightly different from the air
Never replace a fuse with that of wrong rated current or
other wires when a fuse blows out.
Use of wire or copper wire may cause the unit to break down
or cause a fire.
conditioner you purchased(depend on model). The actual shape shall prevail.
Symptom 2: Change into the fan mode during
cooling mode
Never use a damp cloth on the remote controller.
The air-in side should face up when using vacuum cleaner.
Do not use a chemically-treted duster for wiping or leave
such material on the unit for long.
it may damage or fade the surface of the unit.
The air-in side should face down when using water.
Do not use benzine, thinner, polishing powder, or similar
solvents for cleaning.
These may cause the plastic surface to crack or deform.
In order to prevent the indoor evaporator frosting, the system
will change into fan mode automatically, restore to the cooling
mode after soon.
(eg. at the beginning of the season)
Do not dry out the air filter under direct sunshine or with fire.
The refrigerant in the air conditioner is safe and normally
does not leak.
If the refrigerant leaks in the room, contact with a fire of a
burner, a heater or a cooker may result in a harmful gas.
The appliance is not intended for use by young children
or infirm persons without supervision.
CAUTION
Do not use the air conditioner for other purposes.
In order to avoid any quality deterioration, do not use the unit
for cooling precision instruments, food, plants, animals or
works of art.
Before cleaning, be sure to stop the operation, turn the
breaker off or pull out the supply cord.
Otherwise, an electric shock and injury may result.
Be sure the air conditioner is grounded.
In order to avoid electric shock, make sure that the unit is
grounded and that the earth wire is not connected to gas or
water pipe, lightning conductor or telephone earth wire.
Fig.6-1
3.2-10.5KW
Open the air intake with the screwdriver or something like
that .(Refer to Fig.6-1)
Take out the air filter.(Refer to Fig.6-2)
Clean the air cleaning filter with water or vacuum cleaer,then
dry it in cool place.
Re-install the air filter in the reverse order of Fig.6-2.
2
14-16KW
Directly pull out the air filter from air inlet as indicated in
Fig.6-3.
Clean the air cleaning filter with water or vacuum cleaner,
then dry it in cool place.
Indoor fan motor speed out of control
E8
2
In-Out door unit C OMM. C heck ing
channel is abnormal
E1
5
Pipe TEMP. Sens or check ing
channel is abnormal(T2B)
E4
6
EPPR OM malf unct ion
E7
A continuous low "shah" sound is heard when the system is in
cooling operation or at a stop.
When the drain pump (optional accessories) is in operation,this
noise is heard.
Fig.6-2
Water leaks from indoor unit.
Other malfunctions.
If the system does not properly operate except the above
mentioned cases or the above mentioned malfunctions is
evident, investigate the system according to the following
procedures. (See in Table 8-2)
8.2
Troubles and causes of remote controller
Before asking for serving or repairing, check the following
points.(See in Table 8-3)
7
Wat er-lev el alarm malf unct ion
EE
8
Out door malf unct ion
Ed
9
Indoor twins communication malfunction
F3
Other malfunction of twins
F4
10
11
Symptom 4.2: Indoor unit, outdoor unit
A continuous low hissing sound is heard when the system is in
operation.
This is the sound of refrigerant gas flowing through both indoor
and outdoor units.
A hissing sound which is heard at the start or immediately after
stopping operation or defrost operation.
This is the noise of refrigerant caused by flow stop or flow
change.
Fig.6-3
Symptom 4.3: Outdoor unit
When the tone of operating noise changes.
This noise is caused by the change of frequency.
7. FOLLOWING SYMPTOMS ARE NOT AIR
CONDITIONER TROUBLES
Symptom 5: Dust comes out of the unit
When the unit is used for the first time in a long time.
This is because dust has gotten into the unit.
Symptom 1: The system does not operate
The air conditioner does not start immediately after the ON/OFF
button on the romote controller is pressed.
If the operation lamp lights, the system is in normal condition.To
prevent overloading of the compressor motor, the air
conditioner starts 3 minutes after it is turned ON.
If the operation lamp and the "PRE-DEF indicator(cooling and
heating type) or fan only indicator(cooling only type)" light, it
means you choose the heating model, When just starting, if the
compressor has not started, the indoor unit appears "anti cold
wind" protection because of its overlow outlet temperature.
owner’s manual
5
Symptom 6: The units can give off odours
The unit can absorb the smell of rooms, furniture, cigarettes,
etc., and then emit it again.
Symptom 7: The outdoor unit fan does not
spin.
During operation. The speed of the fan is controlled in order to
optimize product operation.
owner’s manual
6
Flas hing at 2.5HZ
LED 2
TIMER
Unit does not start
Air flowing normally but
completely can't cooling
Units start or stop frequently
Low cooling effect
Flas hing at 0.5HZ
LED 3
DEF.FAN
LED 4
ALARM
D ISPLAY
DIGITAL TUBE
•
In-Outdoor unit COMM. Checking
channel is abnormal
•
Room temperature sensor checking channel
is abnormal
Pipe temperature sensor checking channel
is abnormal
E2
•
Outdoor TEMP. sensor checking channel is
abnormal
E4
•
Outdoor malfunction
E6
•
Pump temperature sensor malfunction
E5
•
EEPROM malfunction
E7
•
Water-level alarm malfunction
E8
•
Refrigerant leakage detection malfunction
EC
•
DC motor speed out of control
Eb
•
Outdoor unit low pressure error
Ed
•
Light
3
The air conditioner consists of the indoor unit, the outdoor unit,
the connecting pipe and the remote controller. (See Fig.1)
Function indicators on indoor unit display panel
MANUAL
OPERATION TIMER
DEF./FAN
TIMER
DEF./FAN
ALARM
NOTE:DEF indicator(cooling and heating type)
or FAN indicator(cooling only type)
Infrared signal receiver
Display panel　Fig. 2-1
Timer indicator
PRE-DEF indicator(cooling and heating
type)
or fan only indicator(cooling only type)
Temperature
OPERATION TIMER
DEF./FAN
Mode
ALARM
Alarm indicator
Temporary button
Temperature indecator
Cooling operation
Heating operation
(cooling only type without)
Operation lamp
Temperature
Cooling operation
MANUAL
Timer indicator
Alarm indicator
Alarm indicator
17°C ~ 32°C
( 62 °F ~ 90°F)
4. HINTS FOR ECONOMICAL OPERATION
-7°C ~ 24°C / 20 °F ~ 76°F 0°C ~ 30°C / 32 °F~86°F
Adjust the air flow direction properly to avoid winding toward
your body.
Room
temperature
0°C ~ 50°C / 32 °F~122°F
-15°C ~ 50°C / 5 °F~122°F
(for the models with low
temperature cooling system)
-15°C ~ 24°C / 5 °F~76°F
Drying operation
0°C ~ 50°C / 32 °F~122°F
1
2
For inverter type,this switch is used for after-sales service
purpose only,the user should not push it.
3
Solution
Power failure.
Power switch is off.
Fuse of power switch may have burned.
Batteries of remote controller exhausted
or other problem of controller.
Wait for the comeback of power.
Switch on the power.
Replace.
Replace the batterises or check the
controller.
Temperature is not set correctly.
Be in 3 minutes protection
compressor.
Set the temperature properly.
Wait.
of
Refrigerant is too little or too much.
Air or no concretingc gas in the
refrigerating circuit.
Compressor is malfunction.
Voltage is too high or too low.
System circuit is blocked.
Check leakage, and rightly recharge
refrigerant.
Vacuum and recharge refrigerant.
Maintenance or change compressor.
Install manostat.
Find reasons and solution.
Outdoor unit and indoor unit heat
exchanger is dirty.
The air filter is dirty.
Inlet/outlet of indoor/outdoor units is
blocked.
Doors and windows are open
Sunlight directly shine.
Too much heat resource.
Outdoor temp. is too high.
Leakage of refrigerant or lack of
refrigerant.
Clean the heat exchanger.
Clean the air filter.
Eliminate all dirties and make air
smooth.
Close doors and windows.
Make curtains in order to shelter from
sunshine.
Reduce heat source.
AC cooling capacity reduces (normal).
Check leakage and rightly recharge
refrigerant.
Outdoor temperature is lower than 7 C
Doors and windows not completely
closed.
Leakage of refrigerant or
lack of
refrigerant.
Use heating device.
refrigerant.
Fig. 5-2
When heating
Adjust the louver downwards. (vertically)
5.2
Adjust the Vertical louver
Auto-swing
Press SWING H button, the louver will swing left and right
automatically.
Adjust the room temperature properly to get a comfortable
situation and to avoid supercooling and superheat.
In cooling, close the curtains to avoid direct sunlight.
Fig. 5-4
To keep cool or warm air in the room, never open doors or
windows more often than necessary.
17°C ~ 32°C
( 62 °F ~ 90°F)
Set the timer for the desired operating time.
0°C ~ 30°C / 32 °F~86°F
Never put obstructions near the air outlet or the air inlet. Or it
will cause lower efficiency, even a sudden stop.
17°C ~ 32°C
( 62 °F ~ 90°F)
If you don't plan to use the unit for a long time, please disconnect power and remove the batteries from the remote controller. When the power switch is connected, some energy will be
consumed, even if the air conditioner isn't in operation. So
please disconnect the power to save energy. And please
switch the power on 12 hours before you restart the unit to
ensure a smooth operation.
NOTE
Causes
The following should be noticed to ensure an economical operation.
(Refer to corresponding chapterfor details)
17°C ~ 32°C
( 62 °F ~ 90°F)
Outdoor
temperature
Heating operation
Timer indicator
For some models, the machine is special designed with louver
angle memory function.Power failure during operation or
pressing the ON/OFF button on the remote controller will stop
the unit completely.When the power restores or pressing the
ON/OFF button on the remote controller again,the unit restarts
automatically with the previous open angle of the horizontal
louver by the memory function.So we strongly recommend that
the open angle of the horizontal louver should not be set too
small,in case the condensed water forms and drops from the
horizontal louver. Press the Manual control button and the open
angle of the horizontal louver will be restored to the standard
angle.
Fig. 5-3
18°C ~ 43°C / 64 °F~109°F
-7°C ~ 43°C / 20 °F~109°F
18°C ~ 52°C / 64 °F~126°F
(for special tropical models)
18°C ~ 52°C / 64 °F~126°F
Mode
type)
Louver Angle Memory Function(optional):
Table 3-2(for inverter type air conditioner)
Temporary button
When cooling
Adjust the louver horizontally.
,
With this new technology, the dipsplay area will appear EC (if
applicable) and the LED indication lamps continue flashing
when the outdoor unit detects refrigerant leakage.
Room
temperature
18°C ~ 43°C / 64 °F~109°F
Drying operation
type)
Operation lamp
,
Outdoor
temperature
Fig. 5-1
Refrigerant Leakage Detection(optional):
Table 3-1
MANUAL
Operation lamp
Disconnect the unit with the power and then connect the unit
with the power again. Push the ON/OFF button on the remote
controller to restart operation.
Use the system in the following temperature for safe and
effective operation. The Max operation temperature for
the air conditioner.(Cooling/Heating)
MANUAL
Manual Swing
Adjust the louver to achieve better cooling/heating effects
when cooling /heating.
Lighting or a car wireless telephone operating nearby
may cause the unit to malfunction.
3. AIR CONDITIONER OPERATIONS AND
PERFORMANCE
Adjust the horizontal louver
Auto-swing
Press SWING V button, the louver will swing up and down
automatically.
To restart operation, push the ON/OFF button on the
remote controller.
This manual does not include Remote Controller
Operations, see the<<Remote Controller Owner's
manual>> packed with the unit for details.
OPERATION
5.1
The OPERATION lamp on the indoor unit will start
flashing when power is restored.
NOTE
ALARM
5. ADJUSTING AIR FLOW DIRECTION
Power failure during operation will stop the unit completely.
MANUAL
Power failure
OFF
The OPERATION lamp goes off. The air conditioner is OFF
while the remote controller operation is enabled.
If air conditioner is used outside the above conditions, it may
cause the unit to function abnormally.
The phenomenon is normal that the surface of air
conditioning may condense water when the relative larger
humidity in room, please close the door and window.
Optimum performance will be achieved within these
operating temperature range.
Table 8-3
Symptoms
Table 8-1b
LED 1
OPERATION
3
Applicable to inverter air conditioner only
MALFU N C T ION & PROT EC T ION D EFIN E
A protection feature prevents the air conditioner from being
activated for approximately 3 minutes when it restarts immediately after operation.
FORCED COOL
The OPERATION lamp flashes, the air conditioner will turn to
FORCED AUTO after it is enforced to cool with a wind speed of
HIGH for 30 minutes. The remote controller operation is
disabled.
owner’s manual
Low heating effect
NO.
2
2
EC
Light
A "pishi-pishi" squeaking sound is heard when the system stops
after heating operation.
Expansion and contraction of plastic parts caused by
temperature change make this noise.
If the air conditioner is installed in a dust place, clean the
the air filter frequent.
1
1
E3
Obstacles and water enter the unit.
2. TEMPORARY OPERATIONS
Three-minute protection feature
1 FORCED AUTO
The OPERATION lamp is lit, and the air conditioner will run
under FORCED AUTO mode. The remote controller operation is
enabled to operate according to the received signal.
owner’s manual
D ISPLAY
DIGITAL TUBE
channel is abnormal(T2)
Symptom 4.1: Indoor unit
If the accumulated dust is too heavy to be cleaned, please
replace the filter with a new one(replaceable air filter is an
optional fitting).
LED 4
ALARM
4
(eg. at the end of the season)
The air filter can prevent the dust or other particulate from
going inside. In case of blockage of the filter, the working
efficiency of the air conditioner may greatly decrease.
Therefore, the filter must be cleaned once two weeks
during long time usage.
LED 3
DEF.FAN
A safety device such as a fuse, a breaker frequently actuates.
Sptom 4: Noise of air conditionerscooling
Cleaning the air filter
LED 2
TIMER
When the system is changed over to heating operation after
defrost operation Moisture generated by defrost becomes
steam and is exhausted.
Clean air filters and casings of indoor units. Refer to "
Cleaning the air filter" for details on how to proceed and
make sure to install cleaned air filters back in the same
position.
LED 1
OPERATION
E2
Maintenance before a long stop period
Let the indoor units run in fan only operation for about half
a day in order to dry the interior of the units.
ALARM
Table 8-2
R oom TEMP. s ens or check ing
channel is abnormal
Air filter
NO.
DEF./FAN
For fixed-frequency type,this function is used to operate the unit
temporarily in case you misplace the remote controller or its
batteries are exhausted. Two modes including FORCED
AUTO and FORCED COOL can be selected through the
TEMPORARY BUTTON on the air-in grill control box of the
indoor unit. Once you push this button, the air conditioner will
run in such order: FORCED AUTO, FORCED COOL, OFF,
and back to FORCED AUTO.
Children should be supervised to ensure that they do not
play with the appliance.
In order to avoid injury, do not remove the fan guard of
the outdoor unit.
3
When humidity is high during cooling operation If the interior of
an indoor unit is extremely contaminated, the temperature
distribution inside a room becomes uneven. It is necessary to
clean the interior of the indoor unit. Ask your dealer for details
on cleaning the unit. This operation requires a qualified service
erson
This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities,or lack of experience and knowledge,
unless they have been given supervision or instruction
concerning use of the appliance by a person
responsible for their safety.
In order to avoid electric shock or fire, make sure that an
earth leak detector is installed.
Remote controller receives malfunction or the button does not
work well.
Air Inlet
Turn on the power at least 12 hours before operating the
unit in order to ensure smoother operation. As soon as he
power is turned on, the remote controller displays appear.
The operation lamp is flashing rapidly (5Hz) This lamp is still
flashing rapidly after turn off the power and turn on again.　(See in Table 8-1a and Table 8-1b)
This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe way
and understand the hazards involved. Children shall not
play with the appliance.Cleaning and user maintenance
shall not be made by children without supervision.
TIMER
Do not install the air conditioner at any place where
flammable gas may leak out.
If the gas leaks out and stays around the air conditioner, a
fire may break out.
Table 8-1a
Troubles and causes of air conditioner
If one of the following malfunctions occur, stop operation, shut
off the power, and contact with your dealer.
Do not place appliances which produce open fire in
places exposed to the air flow from the unit or under the
indoor unit.
It may cause incomplete combustion or deformation of the
unit due to the heat.
Turn off any combustible heating devices, ventilate the
room, and contact the dealer where you purchased the
unit.
Do not use the air conditioner until a service person confirms
that the portion where the refrigerant leaks is repaired.
Symptom 3: White mist comes out of a unit
Check and remove everything that might be blocking inlet
and outlet vents of indoor units and outdoor units.
Clean air filters and casings of indoor units.
Refer to "Cleaning the air filter" for details on how to
proceed and make sure to install cleaned air filters back in
the same position.
8.1
When the room temperature drops to the set temperature, the
compressor goes off and the indoor unit changes to fan mode;
when the temperature rises up, the compressor starts again. It
is same in the heating mode.
CAUTION
Maintenance after a long stop period
8. TROUBLESHOOTING
Do not operate the air conditioner when using a room
fumigation - type insecticide.
Failure to observe could cause the chemicals to become
deposited in the unit, which could endanger the health of
those who are hypersensitive to chemicals.
OPERATION
Do not allow a child to mount on the outdoor unit or
avoid placing any object on it.
Falling or tumbling may result in injury.
To prevent refrigerant leak, contact your dealer.
When the system is installed and runs in a small room, it is
required to keep the concentration of the refrigerant, if by any
chance coming out, below the limit. Otherwise, oxygen in the
room may be affected, resulting in a serious accident.
MANUAL
Do not operate your air conditioner in a wet room such
as a bathroom or laundry room.
Never expose little children, plants or animals directly to
the air flow.
Adverse influence to little children, animals and plants may
result.
If electrical appliances are disposed of in landfills or
dumps, hazardous substances can leak into the
groundeater and get into the food chain, damaging your
health and well-being.
1
NOTE
Never touch the internal parts of the controller.
Do not remove the front panel. Some parts inside are
dangerous to touch, and a machine trouble may happen.
Do not dispose of electrical appliances as unsorted
municipal waste, use separate collection facilities.
Contact you local government for information regarding the
connection systems available.
owner’s manual
A wet cloth may be used to clean the indoor unit if it is
very dirty.
Arrange the drain hose to ensure smooth drainage.
Incomplete drainage may cause wetting of the building,
furniture etc.
Do not dispose this product as unsorted municipal
waste. Collection of such waste separately for special
treatment is necessary.
WARNING
Thank you very much for purchasing our air conditioner,
Before using your air conditioner, please read this manual carefully and keep it for future reference.
Never touch the air outlet or the horizontal blades while
the swing flap is in operation.
Fingers may become caught or the unit may break down.
Never inspect or service the unit by yourself.
Ask a qualified service person to perform this work.
OUTDOOR UNIT
1
2
3
4
5
6
Do not place items which might be damaged by moisture
under the indoor unit.
Condensation may form if the humidity is above 80%, the
drain outlet is blocked or the filter is polluted.
CK
7
Ceiling And Floor Type
Never use a flammable spray such as hair spray, lacquer
or paint near the unit.
It may cause a fire.
E ON
8
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
Do not touch the heat exchanger fins.
These fins are sharp and could result in cutting injuries.
E OFF
5
MANUAL
Do not operate the air conditioner with a wet hand.
An electric shock may happen.
A clogged air filter will reduce cooling or heating efficiency,
please clean it once two weeks.
6. MAINTENANCE
CAUTION
Before you clean the air conditioner, be sure the power
supply is off.
Check if the wiring is not broken off or disconnected.
Use a dry cloth to wipe the indoor unit and remote
controller.
owner’s manual
4
QSDLU-002AEN
Symptoms
The fan speed can not be
changed.
Causes
Solution
Check whether the MODE
indicated on the display is
"AUTO"
When the automatic mode is
selected, the air conditioner will
automatically change the fan
speed.
"DRY"
When dry operation is selected,
the air conditioner automatically
change the fan speed. The fan
speed can be selected during
"COOL" , "FAN ONLY", and "HEAT".
The remote controller signal is
not transmitted even when
the ON/OFF button is pushed.
Check whether the batteries
in the remote controller are
exhausted.
The TEMP. indicator does
not come on.
FAN ONLY
The temperature cannot be set during
FAN mode.
Check whether the timer
operation has come to an
end when the TIMER OFF
is indicated on the display.
The air conditioner operation will
stop up to the set time.
operation is started when
the TIMER ON is indicated
on the display.
Up to the set time, the air conditioner
will automatically start and the
appropriate indicator will go off.
Check whether the signal
transmitter of the remote
controller is properly directed
to the infrared signal receiver
of the indoor unit when the
ON/OFF button is pressed.
Directly transmit the signal transmitter
of the remote controller to the infrared
signal receiver of the indoor unit, and
then repeatly push the ON/OFF button
twice.
The indication on the display
disappears after a lapse of
time.
The TIMER ON indicator
goes off after a lapse of
certain time.
No receiving tone sounds
from the indoor unit even
when the ON/OFF button is
pressed.
The power supply is off.
The design and specifications are subject to change without prior notice for product
improvement.Consult with the sales agency or manufacturer for details.
E1
E3
Flas hing at 5HZ
202000192523
20130925
Flas hing at 1HZ
Applicable to fixed-frequency air conditioner only
owner’s manual
7
owner’s manual
8
Original instructions
3
CONTENTS
INDOOR UNIT
inlet or outlet.
PAGE
1
TEMPORARY OPERATIONS........................................................................2
TO
OL
MAINTENANCE...............................................................................................4
6
TEM
SE P
T
Y
AT
2
4
AU
CO
DR
HE
FAN
CLOC
K
SET
FAN
MO
HINTS FOR ECONOMICAL OPERATION...................................................4
DE
HOU
R
SPEE
D
FAN
SPE
ED
SW
SW
AIR
RESE
T LOCK
ING
ING
C/H
DIRE
CTIO
N
OK
TIM
ECO
TIM
CLO
TROUBLES........................................................................................................5
CK
E ON
MANUAL
8
7
WARNING
OR
wiring regulations.
9
7
CAUTION
7
8
8
to the equipment.
9
WARNING
8
8
8
INDOOR UNIT
Fig.1
OUTDOOR UNIT
7
8
9
Installation part
Connecting pipe
Air inlet
Air outlet
Display panel
maintenance.
Remote controller
Drain pipe
NOTE
damage.
or cause a fire.
cooling mode
mode after soon.
does not leak.
CAUTION
works of art.
Fig.6-1
3.2-10.5KW
2
14-16KW
Fig.6-3.
E8
2
channel is abnormal
E1
5
E4
6
E7
noise is heard.
Fig.6-2
Other malfunctions.
8.2
7
EE
8
Ed
9
F3
F4
10
11
operation.
and outdoor units.
change.
Fig.6-3
owner’s manual
5
spin.
owner’s manual
6
Flas hing at 2.5HZ
LED 2
TIMER
Unit does not start
Low cooling effect
Flas hing at 0.5HZ
LED 3
DEF.FAN
LED 4
ALARM
D ISPLAY
DIGITAL TUBE
•
channel is abnormal
•
is abnormal
is abnormal
E2
•
abnormal
E4
•
Outdoor malfunction
E6
•
E5
•
EEPROM malfunction
E7
•
E8
•
EC
•
Eb
•
Ed
•
Light
3
MANUAL
OPERATION TIMER
DEF./FAN
TIMER
DEF./FAN
ALARM
Timer indicator
type)
Temperature
OPERATION TIMER
DEF./FAN
Mode
ALARM
Alarm indicator
Temporary button
Cooling operation
Heating operation
Operation lamp
Temperature
Cooling operation
MANUAL
Timer indicator
Alarm indicator
Alarm indicator
17°C ~ 32°C
( 62 °F ~ 90°F)
-7°C ~ 24°C / 20 °F ~ 76°F 0°C ~ 30°C / 32 °F~86°F
your body.
Room
temperature
0°C ~ 50°C / 32 °F~122°F
-15°C ~ 50°C / 5 °F~122°F
-15°C ~ 24°C / 5 °F~76°F
Drying operation
0°C ~ 50°C / 32 °F~122°F
1
2
3
Solution
Power failure.
Replace.
controller.
compressor.
Wait.
of
refrigerant.
Install manostat.
exchanger is dirty.
blocked.
refrigerant.
smooth.
sunshine.
Reduce heat source.
refrigerant.
closed.
lack of
refrigerant.
Use heating device.
refrigerant.
Fig. 5-2
When heating
5.2
Auto-swing
automatically.
Fig. 5-4
17°C ~ 32°C
( 62 °F ~ 90°F)
0°C ~ 30°C / 32 °F~86°F
17°C ~ 32°C
( 62 °F ~ 90°F)
NOTE
Causes
17°C ~ 32°C
( 62 °F ~ 90°F)
Outdoor
temperature
Heating operation
Timer indicator
angle.
Fig. 5-3
18°C ~ 43°C / 64 °F~109°F
-7°C ~ 43°C / 20 °F~109°F
18°C ~ 52°C / 64 °F~126°F
18°C ~ 52°C / 64 °F~126°F
Mode
type)
Temporary button
When cooling
,
Room
temperature
18°C ~ 43°C / 64 °F~109°F
Drying operation
type)
Operation lamp
,
Outdoor
temperature
Fig. 5-1
Table 3-1
MANUAL
Operation lamp
MANUAL
Manual Swing
PERFORMANCE
Auto-swing
automatically.
remote controller.
OPERATION
5.1
NOTE
ALARM
MANUAL
Power failure
OFF
Table 8-3
Symptoms
Table 8-1b
LED 1
OPERATION
3
FORCED COOL
disabled.
owner’s manual
Low heating effect
NO.
2
2
EC
Light
1
1
E3
1 FORCED AUTO
owner’s manual
D ISPLAY
DIGITAL TUBE
optional fitting).
LED 4
ALARM
4
LED 3
DEF.FAN
LED 2
TIMER
position.
LED 1
OPERATION
E2
ALARM
Table 8-2
channel is abnormal
Air filter
NO.
DEF./FAN
the outdoor unit.
3
erson
work well.
Air Inlet
TIMER
fire may break out.
Table 8-1a
indoor unit.
unit.
the same position.
8.1
CAUTION
8. TROUBLESHOOTING
OPERATION
MANUAL
the air flow.
result.
1
NOTE
owner’s manual
very dirty.
furniture etc.
damage.
9
OUTDOOR UNIT
1
2
3
4
5
6
TROUBLESHOOTING....................................................................................6
8
E OFF
5
AIR CONDITIONER OPERATIONS AND PERFORMANCE....................3
M
OWNER'S
6. MAINTENANCE
CAUTION
supply is off.
controller.
owner’s manual
4
QSDLU-002AEN
Symptoms
changed.
Causes
Solution
"AUTO"
speed.
"DRY"
exhausted.
not come on.
FAN ONLY
FAN mode.
on the display.
twice.
time.
certain time.
pressed.
E1
E3
Flas hing at 5HZ
202000192523
20130925
Flas hing at 1HZ
owner’s manual
7
owner’s manual
8
CONTENTS
3
INDOOR UNIT
PAGE
inlet or outlet.
1
4
AU
TO
CO
OL
DR
AT
K
HOU
R
SPEE
D
FAN
SPE
ED
SW
SW
AIR
RESE
T LOCK
ING
ING
C/H
DIRE
CTIO
TIM
TIM
OWNER'S
N
OK
ECO
CLO
6
CLOC
SET
FAN
DE
TROUBLES..........5
TEM
SE P
T
Y
HE
FAN
MO
M
MAINTENANCE.........................................................................................4
2
8
damage.
damage.
9
OR
wiring regulations.
9
7
8
CAUTION
7
8
to the equipment.
9
WARNING
8
8
8
INDOOR UNIT
Fig.1
OUTDOOR UNIT
7
8
9
Installation part
Connecting pipe
Air inlet
Air outlet
Display panel
maintenance.
Remote controller
Drain pipe
NOTE
or cause a fire.
cooling mode
mode after soon.
does not leak.
CAUTION
works of art.
Fig.6-1
3.2-10.5KW
2
14-16KW
Fig.6-3.
E8
2
channel is abnormal
E1
5
E4
6
E7
noise is heard.
Fig.6-2
Other malfunctions.
8.2
7
EE
8
Ed
9
F3
F4
10
11
operation.
and outdoor units.
change.
Fig.6-3
owner’s manual
5
spin.
owner’s manual
6
Flas hing at 2.5HZ
LED 2
TIMER
Unit does not start
Low cooling effect
Flas hing at 0.5HZ
LED 3
DEF.FAN
LED 4
ALARM
D ISPLAY
DIGITAL TUBE
•
channel is abnormal
•
is abnormal
is abnormal
E2
•
abnormal
E4
•
Outdoor malfunction
E6
•
E5
•
EEPROM malfunction
E7
•
E8
•
EC
•
Eb
•
Ed
•
Light
3
MANUAL
OPERATION TIMER
DEF./FAN
TIMER
DEF./FAN
ALARM
Timer indicator
type)
Temperature
OPERATION TIMER
DEF./FAN
Mode
ALARM
Alarm indicator
Temporary button
Cooling operation
Heating operation
Operation lamp
Temperature
Cooling operation
MANUAL
Timer indicator
Alarm indicator
Alarm indicator
17°C ~ 32°C
( 62 °F ~ 90°F)
-7°C ~ 24°C / 20 °F ~ 76°F 0°C ~ 30°C / 32 °F~86°F
your body.
Room
temperature
0°C ~ 50°C / 32 °F~122°F
-15°C ~ 50°C / 5 °F~122°F
-15°C ~ 24°C / 5 °F~76°F
Drying operation
0°C ~ 50°C / 32 °F~122°F
1
2
3
Solution
Power failure.
Replace.
controller.
compressor.
Wait.
of
refrigerant.
Install manostat.
exchanger is dirty.
blocked.
refrigerant.
smooth.
sunshine.
Reduce heat source.
refrigerant.
closed.
lack of
refrigerant.
Use heating device.
refrigerant.
Fig. 5-2
When heating
5.2
Auto-swing
automatically.
Fig. 5-4
17°C ~ 32°C
( 62 °F ~ 90°F)
0°C ~ 30°C / 32 °F~86°F
17°C ~ 32°C
( 62 °F ~ 90°F)
NOTE
Causes
17°C ~ 32°C
( 62 °F ~ 90°F)
Outdoor
temperature
Heating operation
Timer indicator
angle.
Fig. 5-3
18°C ~ 43°C / 64 °F~109°F
-7°C ~ 43°C / 20 °F~109°F
18°C ~ 52°C / 64 °F~126°F
18°C ~ 52°C / 64 °F~126°F
Mode
type)
Temporary button
When cooling
,
Room
temperature
18°C ~ 43°C / 64 °F~109°F
Drying operation
type)
Operation lamp
,
Outdoor
temperature
Fig. 5-1
Table 3-1
MANUAL
Operation lamp
MANUAL
Manual Swing
PERFORMANCE
Auto-swing
automatically.
remote controller.
OPERATION
5.1
NOTE
ALARM
MANUAL
Power failure
OFF
Table 8-3
Symptoms
Table 8-1b
LED 1
OPERATION
3
FORCED COOL
disabled.
owner’s manual
Low heating effect
NO.
2
2
EC
Light
1
1
E3
1 FORCED AUTO
owner’s manual
D ISPLAY
DIGITAL TUBE
optional fitting).
LED 4
ALARM
4
LED 3
DEF.FAN
LED 2
TIMER
position.
LED 1
OPERATION
E2
ALARM
Table 8-2
channel is abnormal
Air filter
NO.
DEF./FAN
the outdoor unit.
3
erson
work well.
Air Inlet
TIMER
fire may break out.
Table 8-1a
indoor unit.
unit.
the same position.
8.1
CAUTION
8. TROUBLESHOOTING
OPERATION
MANUAL
the air flow.
result.
1
NOTE
owner’s manual
very dirty.
furniture etc.
WARNING
OUTDOOR UNIT
1
2
3
4
5
6
CK
7
E ON
8
E OFF
5
MANUAL
6. MAINTENANCE
CAUTION
supply is off.
controller.
owner’s manual
4
QSDLU-002AEN
Symptoms
changed.
Causes
Solution
"AUTO"
speed.
"DRY"
exhausted.
not come on.
FAN ONLY
FAN mode.
on the display.
twice.
time.
certain time.
pressed.
E1
E3
Flas hing at 5HZ
202000192523
20130925
Flas hing at 1HZ
owner’s manual
7
owner’s manual
8
CONTENTS
3
INDOOR UNIT
PAGE
inlet or outlet.
1
4
AU
TO
CO
OL
DR
AT
TROUBLES..........5
CLOC
K
SET
FAN
DE
HOU
R
SPEE
D
FAN
SPE
ED
SW
SW
AIR
RESE
T LOCK
ING
ING
C/H
DIRE
CTIO
TIM
TIM
OWNER'S
N
OK
ECO
CLO
6
TEM
SE P
T
Y
HE
FAN
MO
M
MAINTENANCE.........................................................................................4
2
damage.
8
WARNING
OR
wiring regulations.
9
7
8
CAUTION
7
8
to the equipment.
9
WARNING
8
8
8
INDOOR UNIT
OUTDOOR UNIT
1
2
3
4
5
6
7
8
9
Installation part
Fig.1
Connecting pipe
Air inlet
Air outlet
Display panel
maintenance.
Remote controller
Drain pipe
NOTE
or cause a fire.
cooling mode
mode after soon.
does not leak.
CAUTION
Fig.6-1
3.2-10.5KW
2
14-16KW
Fig.6-3.
E8
2
channel is abnormal
E1
5
E4
6
E7
noise is heard.
Fig.6-2
Other malfunctions.
8.2
7
EE
8
Ed
9
F3
F4
10
11
operation.
and outdoor units.
change.
Fig.6-3
owner’s manual
5
spin.
owner’s manual
6
Flas hing at 2.5HZ
LED 2
TIMER
Unit does not start
Low cooling effect
Flas hing at 0.5HZ
LED 3
DEF.FAN
LED 4
ALARM
D ISPLAY
DIGITAL TUBE
•
channel is abnormal
•
is abnormal
is abnormal
E2
•
abnormal
E4
•
Outdoor malfunction
E6
•
E5
•
EEPROM malfunction
E7
•
E8
•
EC
•
Eb
•
Ed
•
Light
3
MANUAL
Power failure
DEF./FAN
TIMER
DEF./FAN
ALARM
,
Temperature
OPERATION TIMER
DEF./FAN
angle.
Table 3-1
Mode
ALARM
Outdoor
temperature
When cooling
,
MANUAL
Fig. 5-1
PERFORMANCE
Manual Swing
OPERATION
Auto-swing
automatically.
remote controller.
NOTE
ALARM
5.1
MANUAL
OPERATION TIMER
OFF
Room
temperature
Fig. 5-2
When heating
Fig. 5-3
18°C ~ 43°C
Timer indicator
type)
Cooling operation
MANUAL
Operation lamp
Alarm indicator
Temporary button
type)
Operation lamp
-7°C ~ 24°C
0°C ~ 30°C
Drying operation
18°C ~ 43°C
17°C ~ 32°C
1
2
MANUAL
Timer indicator
Alarm indicator
your body.
3
Alarm indicator
Power failure.
Replace.
controller.
compressor.
Wait.
of
refrigerant.
Install manostat.
exchanger is dirty.
blocked.
refrigerant.
smooth.
sunshine.
Reduce heat source.
refrigerant.
closed.
lack of
refrigerant.
Use heating device.
refrigerant.
Fig. 5-4
Solution
Auto-swing
automatically.
Causes
Timer indicator
5.2
NOTE
Operation lamp
17°C ~ 32°C
Heating operation
Temporary button
type)
-7°C ~ 43°C
Table 8-3
Symptoms
Table 8-1b
LED 1
OPERATION
3
FORCED COOL
disabled.
owner’s manual
Low heating effect
NO.
2
2
EC
Light
1
1
E3
1 FORCED AUTO
owner’s manual
D ISPLAY
DIGITAL TUBE
optional fitting).
LED 4
ALARM
4
LED 3
DEF.FAN
LED 2
TIMER
position.
LED 1
OPERATION
E2
ALARM
Table 8-2
channel is abnormal
Air filter
NO.
DEF./FAN
the outdoor unit.
3
erson
work well.
Air Inlet
works of art.
TIMER
fire may break out.
Table 8-1a
indoor unit.
unit.
the same position.
8.1
CAUTION
8. TROUBLESHOOTING
OPERATION
MANUAL
the air flow.
result.
1
NOTE
owner’s manual
very dirty.
furniture etc.
damage.
9
OUTDOOR UNIT
CK
7
E ON
8
E OFF
5
MANUAL
6. MAINTENANCE
CAUTION
supply is off.
controller.
owner’s manual
4
QSDLU-002AEN
Symptoms
changed.
Causes
Solution
"AUTO"
speed.
"DRY"
exhausted.
not come on.
FAN ONLY
FAN mode.
on the display.
twice.
time.
certain time.
pressed.
E1
E3
Flas hing at 5HZ
202000192523
20130925
Flas hing at 1HZ
owner’s manual
7
owner’s manual
8
CONTENTS
3
INDOOR UNIT
PAGE
inlet or outlet.
1
4
AU
TO
CO
OL
DR
AT
K
HOU
R
SPEE
D
FAN
SPE
ED
SW
SW
AIR
RESE
T LOCK
ING
ING
C/H
DIRE
CTIO
TIM
TIM
OWNER'S
N
OK
ECO
CLO
6
CLOC
SET
FAN
DE
TROUBLES..........5
TEM
SE P
T
Y
HE
FAN
MO
M
MAINTENANCE.........................................................................................4
2
8
damage.
damage.
9
OR
wiring regulations.
9
7
8
CAUTION
7
8
to the equipment.
9
WARNING
8
8
8
INDOOR UNIT
Fig.1
OUTDOOR UNIT
7
8
9
Installation part
Connecting pipe
Air inlet
Air outlet
Display panel
maintenance.
Remote controller
Drain pipe
NOTE
or cause a fire.
cooling mode
mode after soon.
does not leak.
CAUTION
works of art.
Fig.6-1
3.2-10.5KW
2
14-16KW
Fig.6-3.
E8
2
channel is abnormal
E1
5
E4
6
E7
noise is heard.
Fig.6-2
Other malfunctions.
8.2
7
EE
8
Ed
9
F3
F4
10
11
operation.
and outdoor units.
change.
Fig.6-3
owner’s manual
5
spin.
owner’s manual
6
Flas hing at 2.5HZ
LED 2
TIMER
Unit does not start
Low cooling effect
Flas hing at 0.5HZ
LED 3
DEF.FAN
LED 4
ALARM
D ISPLAY
DIGITAL TUBE
•
channel is abnormal
•
is abnormal
is abnormal
E2
•
abnormal
E4
•
Outdoor malfunction
E6
•
E5
•
EEPROM malfunction
E7
•
E8
•
EC
•
Eb
•
Ed
•
Light
3
MANUAL
OPERATION TIMER
DEF./FAN
TIMER
DEF./FAN
ALARM
Timer indicator
type)
Temperature
OPERATION TIMER
DEF./FAN
Mode
ALARM
Alarm indicator
Temporary button
Cooling operation
Heating operation
Operation lamp
Temperature
Cooling operation
MANUAL
Timer indicator
Alarm indicator
Alarm indicator
17°C ~ 32°C
( 62 °F ~ 90°F)
-7°C ~ 24°C / 20 °F ~ 76°F 0°C ~ 30°C / 32 °F~86°F
your body.
Room
temperature
0°C ~ 50°C / 32 °F~122°F
-15°C ~ 50°C / 5 °F~122°F
-15°C ~ 24°C / 5 °F~76°F
Drying operation
0°C ~ 50°C / 32 °F~122°F
1
2
3
Solution
Power failure.
Replace.
controller.
compressor.
Wait.
of
refrigerant.
Install manostat.
exchanger is dirty.
blocked.
refrigerant.
smooth.
sunshine.
Reduce heat source.
refrigerant.
closed.
lack of
refrigerant.
Use heating device.
refrigerant.
Fig. 5-2
When heating
5.2
Auto-swing
automatically.
Fig. 5-4
17°C ~ 32°C
( 62 °F ~ 90°F)
0°C ~ 30°C / 32 °F~86°F
17°C ~ 32°C
( 62 °F ~ 90°F)
NOTE
Causes
17°C ~ 32°C
( 62 °F ~ 90°F)
Outdoor
temperature
Heating operation
Timer indicator
angle.
Fig. 5-3
18°C ~ 43°C / 64 °F~109°F
-7°C ~ 43°C / 20 °F~109°F
18°C ~ 52°C / 64 °F~126°F
18°C ~ 52°C / 64 °F~126°F
Mode
type)
Temporary button
When cooling
,
Room
temperature
18°C ~ 43°C / 64 °F~109°F
Drying operation
type)
Operation lamp
,
Outdoor
temperature
Fig. 5-1
Table 3-1
MANUAL
Operation lamp
MANUAL
Manual Swing
PERFORMANCE
Auto-swing
automatically.
remote controller.
OPERATION
5.1
NOTE
ALARM
MANUAL
Power failure
OFF
Table 8-3
Symptoms
Table 8-1b
LED 1
OPERATION
3
FORCED COOL
disabled.
owner’s manual
Low heating effect
NO.
2
2
EC
Light
1
1
E3
1 FORCED AUTO
owner’s manual
D ISPLAY
DIGITAL TUBE
optional fitting).
LED 4
ALARM
4
LED 3
DEF.FAN
LED 2
TIMER
position.
LED 1
OPERATION
E2
ALARM
Table 8-2
channel is abnormal
Air filter
NO.
DEF./FAN
the outdoor unit.
3
erson
work well.
Air Inlet
TIMER
fire may break out.
Table 8-1a
indoor unit.
unit.
the same position.
8.1
CAUTION
8. TROUBLESHOOTING
OPERATION
MANUAL
the air flow.
result.
1
NOTE
owner’s manual
very dirty.
furniture etc.
WARNING
OUTDOOR UNIT
1
2
3
4
5
6
CK
7
E ON
8
E OFF
5
MANUAL
6. MAINTENANCE
CAUTION
supply is off.
controller.
owner’s manual
4
QSDLU-002AEN
Symptoms
changed.
Causes
Solution
"AUTO"
speed.
"DRY"
exhausted.
not come on.
FAN ONLY
FAN mode.
on the display.
twice.
time.
certain time.
pressed.
E1
E3
Flas hing at 5HZ
202000192523
20130925
Flas hing at 1HZ
owner’s manual
7
owner’s manual
8
CONTENTS
3
INDOOR UNIT
PAGE
inlet or outlet.
1
4
AU
TO
CO
OL
DR
AT
K
HOU
R
SPEE
D
FAN
SPE
ED
SW
SW
AIR
RESE
T LOCK
ING
ING
C/H
DIRE
CTIO
TIM
TIM
OWNER'S
N
OK
ECO
CLO
6
CLOC
SET
FAN
DE
TROUBLES..........5
TEM
SE P
T
Y
HE
FAN
MO
M
MAINTENANCE.........................................................................................4
2
8
damage.
damage.
9
OR
wiring regulations.
9
7
8
CAUTION
7
8
to the equipment.
9
WARNING
8
8
8
INDOOR UNIT
Fig.1
OUTDOOR UNIT
7
8
9
Installation part
Connecting pipe
Air inlet
Air outlet
Display panel
maintenance.
Remote controller
Drain pipe
NOTE
or cause a fire.
cooling mode
mode after soon.
does not leak.
CAUTION
works of art.
Fig.6-1
3.2-10.5KW
2
14-16KW
Fig.6-3.
E8
2
channel is abnormal
E1
5
E4
6
E7
noise is heard.
Fig.6-2
Other malfunctions.
8.2
7
EE
8
Ed
9
F3
F4
10
11
operation.
and outdoor units.
change.
Fig.6-3
owner’s manual
5
spin.
owner’s manual
6
Flas hing at 2.5HZ
LED 2
TIMER
Unit does not start
Low cooling effect
Flas hing at 0.5HZ
LED 3
DEF.FAN
LED 4
ALARM
D ISPLAY
DIGITAL TUBE
•
channel is abnormal
•
is abnormal
is abnormal
E2
•
abnormal
E4
•
Outdoor malfunction
E6
•
E5
•
EEPROM malfunction
E7
•
E8
•
EC
•
Eb
•
Ed
•
Light
3
MANUAL
OPERATION TIMER
DEF./FAN
TIMER
DEF./FAN
ALARM
Timer indicator
type)
Temperature
OPERATION TIMER
DEF./FAN
Mode
ALARM
Alarm indicator
Temporary button
Cooling operation
Heating operation
Operation lamp
Temperature
Cooling operation
MANUAL
Timer indicator
Alarm indicator
Alarm indicator
17°C ~ 32°C
( 62 °F ~ 90°F)
-7°C ~ 24°C / 20 °F ~ 76°F 0°C ~ 30°C / 32 °F~86°F
your body.
Room
temperature
0°C ~ 50°C / 32 °F~122°F
-15°C ~ 50°C / 5 °F~122°F
-15°C ~ 24°C / 5 °F~76°F
Drying operation
0°C ~ 50°C / 32 °F~122°F
1
2
3
Solution
Power failure.
Replace.
controller.
compressor.
Wait.
of
refrigerant.
Install manostat.
exchanger is dirty.
blocked.
refrigerant.
smooth.
sunshine.
Reduce heat source.
refrigerant.
closed.
lack of
refrigerant.
Use heating device.
refrigerant.
Fig. 5-2
When heating
5.2
Auto-swing
automatically.
Fig. 5-4
17°C ~ 32°C
( 62 °F ~ 90°F)
0°C ~ 30°C / 32 °F~86°F
17°C ~ 32°C
( 62 °F ~ 90°F)
NOTE
Causes
17°C ~ 32°C
( 62 °F ~ 90°F)
Outdoor
temperature
Heating operation
Timer indicator
angle.
Fig. 5-3
18°C ~ 43°C / 64 °F~109°F
-7°C ~ 43°C / 20 °F~109°F
18°C ~ 52°C / 64 °F~126°F
18°C ~ 52°C / 64 °F~126°F
Mode
type)
Temporary button
When cooling
,
Room
temperature
18°C ~ 43°C / 64 °F~109°F
Drying operation
type)
Operation lamp
,
Outdoor
temperature
Fig. 5-1
Table 3-1
MANUAL
Operation lamp
MANUAL
Manual Swing
PERFORMANCE
Auto-swing
automatically.
remote controller.
OPERATION
5.1
NOTE
ALARM
MANUAL
Power failure
OFF
Table 8-3
Symptoms
Table 8-1b
LED 1
OPERATION
3
FORCED COOL
disabled.
owner’s manual
Low heating effect
NO.
2
2
EC
Light
1
1
E3
1 FORCED AUTO
owner’s manual
D ISPLAY
DIGITAL TUBE
optional fitting).
LED 4
ALARM
4
LED 3
DEF.FAN
LED 2
TIMER
position.
LED 1
OPERATION
E2
ALARM
Table 8-2
channel is abnormal
Air filter
NO.
DEF./FAN
the outdoor unit.
3
erson
work well.
Air Inlet
TIMER
fire may break out.
Table 8-1a
indoor unit.
unit.
the same position.
8.1
CAUTION
8. TROUBLESHOOTING
OPERATION
MANUAL
the air flow.
result.
1
NOTE
owner’s manual
very dirty.
furniture etc.
WARNING
OUTDOOR UNIT
1
2
3
4
5
6
CK
7
E ON
8
E OFF
5
MANUAL
6. MAINTENANCE
CAUTION
supply is off.
controller.
owner’s manual
4
QSDLU-002AEN
Symptoms
changed.
Causes
Solution
"AUTO"
speed.
"DRY"
exhausted.
not come on.
FAN ONLY
FAN mode.
on the display.
twice.
time.
certain time.
pressed.
E1
E3
Flas hing at 5HZ
202000192523
20130925
Flas hing at 1HZ
owner’s manual
7
owner’s manual
8
CONTENTS
3
INDOOR UNIT
PAGE
inlet or outlet.
1
4
AU
TO
CO
OL
DR
AT
TROUBLES..........5
CLOC
K
SET
FAN
DE
HOU
R
SPEE
D
FAN
SPE
ED
SW
SW
AIR
RESE
T LOCK
ING
ING
C/H
DIRE
CTIO
TIM
TIM
OWNER'S
N
OK
ECO
CLO
6
TEM
SE P
T
Y
HE
FAN
MO
M
MAINTENANCE.........................................................................................4
2
8
damage.
damage.
9
OR
wiring regulations.
9
7
8
CAUTION
7
8
to the equipment.
9
WARNING
8
8
8
INDOOR UNIT
Fig.1
OUTDOOR UNIT
7
8
9
Installation part
Connecting pipe
Air inlet
Air outlet
Display panel
maintenance.
Remote controller
Drain pipe
NOTE
or cause a fire.
cooling mode
mode after soon.
does not leak.
CAUTION
works of art.
Fig.6-1
3.2-10.5KW
2
14-16KW
Fig.6-3.
E8
2
channel is abnormal
E1
5
E4
6
E7
noise is heard.
Fig.6-2
Other malfunctions.
8.2
7
EE
8
Ed
9
F3
F4
10
11
operation.
and outdoor units.
change.
Fig.6-3
owner’s manual
5
spin.
owner’s manual
6
Flas hing at 2.5HZ
LED 2
TIMER
Unit does not start
Low cooling effect
Flas hing at 0.5HZ
LED 3
DEF.FAN
LED 4
ALARM
D ISPLAY
DIGITAL TUBE
•
channel is abnormal
•
is abnormal
is abnormal
E2
•
abnormal
E4
•
Outdoor malfunction
E6
•
E5
•
EEPROM malfunction
E7
•
E8
•
EC
•
Eb
•
Ed
•
Light
3
MANUAL
OPERATION TIMER
DEF./FAN
TIMER
DEF./FAN
ALARM
Timer indicator
type)
Temperature
OPERATION TIMER
DEF./FAN
Mode
ALARM
Alarm indicator
Temporary button
Cooling operation
Heating operation
Operation lamp
Temperature
Cooling operation
MANUAL
Timer indicator
Alarm indicator
Alarm indicator
17°C ~ 32°C
( 62 °F ~ 90°F)
-7°C ~ 24°C / 20 °F ~ 76°F 0°C ~ 30°C / 32 °F~86°F
your body.
Room
temperature
0°C ~ 50°C / 32 °F~122°F
-15°C ~ 50°C / 5 °F~122°F
-15°C ~ 24°C / 5 °F~76°F
Drying operation
0°C ~ 50°C / 32 °F~122°F
1
2
3
Solution
Power failure.
Replace.
controller.
compressor.
Wait.
of
refrigerant.
Install manostat.
exchanger is dirty.
blocked.
refrigerant.
smooth.
sunshine.
Reduce heat source.
refrigerant.
closed.
lack of
refrigerant.
Use heating device.
refrigerant.
Fig. 5-2
When heating
5.2
Auto-swing
automatically.
Fig. 5-4
17°C ~ 32°C
( 62 °F ~ 90°F)
0°C ~ 30°C / 32 °F~86°F
17°C ~ 32°C
( 62 °F ~ 90°F)
NOTE
Causes
17°C ~ 32°C
( 62 °F ~ 90°F)
Outdoor
temperature
Heating operation
Timer indicator
angle.
Fig. 5-3
18°C ~ 43°C / 64 °F~109°F
-7°C ~ 43°C / 20 °F~109°F
18°C ~ 52°C / 64 °F~126°F
18°C ~ 52°C / 64 °F~126°F
Mode
type)
Temporary button
When cooling
,
Room
temperature
18°C ~ 43°C / 64 °F~109°F
Drying operation
type)
Operation lamp
,
Outdoor
temperature
Fig. 5-1
Table 3-1
MANUAL
Operation lamp
MANUAL
Manual Swing
PERFORMANCE
Auto-swing
automatically.
remote controller.
OPERATION
5.1
NOTE
ALARM
MANUAL
Power failure
OFF
Table 8-3
Symptoms
Table 8-1b
LED 1
OPERATION
3
FORCED COOL
disabled.
owner’s manual
Low heating effect
NO.
2
2
EC
Light
1
1
E3
1 FORCED AUTO
owner’s manual
D ISPLAY
DIGITAL TUBE
optional fitting).
LED 4
ALARM
4
LED 3
DEF.FAN
LED 2
TIMER
position.
LED 1
OPERATION
E2
ALARM
Table 8-2
channel is abnormal
Air filter
NO.
DEF./FAN
the outdoor unit.
3
erson
work well.
Air Inlet
flashing rapidly after turn off the power and turn on again.　(See in Table 8-1)
TIMER
fire may break out.
Table 8-1a
indoor unit.
unit.
the same position.
8.1
CAUTION
8. TROUBLESHOOTING
OPERATION
MANUAL
the air flow.
result.
1
NOTE
owner’s manual
very dirty.
furniture etc.
WARNING
OUTDOOR UNIT
1
2
3
4
5
6
CK
7
E ON
8
E OFF
5
MANUAL
6. MAINTENANCE
CAUTION
supply is off.
controller.
owner’s manual
4
QSDLU-002AEN
Symptoms
changed.
Causes
Solution
"AUTO"
speed.
"DRY"
exhausted.
not come on.
FAN ONLY
FAN mode.
on the display.
twice.
time.
certain time.
pressed.
E1
E3
Flas hing at 5HZ
202000192523
20130925
Flas hing at 1HZ
owner’s manual
7
owner’s manual
8
CONTENTS
3
INDOOR UNIT
PAGE
1
TO
OL
TROUBLES..........5
CLOC
K
SET
FAN
DE
HOU
R
SPEE
D
FAN
SPE
ED
SW
SW
AIR
RESE
T LOCK
ING
ING
C/H
DIRE
CTIO
TIM
TIM
OWNER'S
N
OK
ECO
CLO
6
TEM
SE P
T
Y
AT
2
4
AU
CO
DR
HE
FAN
MO
M
MAINTENANCE.........................................................................................4
damage.
WARNING
OR
wiring regulations.
9
7
8
CAUTION
7
8
to the equipment.
9
WARNING
8
8
8
INDOOR UNIT
maintenance.
Fig.1
OUTDOOR UNIT
7
8
9
Installation part
Connecting pipe
Air inlet
Air outlet
Display panel
Remote controller
Drain pipe
or cause a fire.
NOTE
cooling mode
mode after soon.
does not leak.
erson
Fig.6-1
Air filter
noise is heard.
Fig.6-2
unit.
CAUTION
works of art.
the outdoor unit.
2
14-16KW
Fig.6-3.
8.2
LED2
TIMER
LED 3
DEF.FAN
LED4
ALARM
•
•
•
is abnormal
is abnormal
•
Outdoor TEM P. sensor checking channel is
abnormal
E4
•
Outdoor malfunction
E6
•
E5
•
EEPROM malfunction
E7
MANUAL
•
EC
•
Eb
•
Ed
Flas hing at 5Hz
DEF./FAN
TIMER
DEF./FAN
ALARM
Timer indicator
type)
Alarm indicator
Temporary button
Temperature
OPERATION TIMER
DEF./FAN
Mode
ALARM
Cooling operation
Heating operation
Operation lamp
Temperature
Cooling operation
MANUAL
Timer indicator
Alarm indicator
Alarm indicator
your body.
Room
temperature
0°C ~ 50°C / 32 °F~122°F
-15°C ~ 50°C / 5 °F~122°F
Drying operation
0°C ~ 50°C / 32 °F~122°F
1
2
3
Unit does not start
Low cooling effect
Flas hing at 1Hz
Low heating effect
Power failure.
Replace.
controller.
compressor.
Wait.
of
refrigerant.
Install manostat.
exchanger is dirty.
blocked.
refrigerant.
smooth.
sunshine.
Reduce heat source.
refrigerant.
closed.
lack of
refrigerant.
Use heating device.
refrigerant.
5.2
Auto-swing
automatically.
Fig. 5-4
17°C ~ 32°C
( 62 °F ~ 90°F)
0°C ~ 30°C / 32 °F~86°F
17°C ~ 32°C
( 62 °F ~ 90°F)
Table 8-3
Solution
When heating
NOTE
Causes
17°C ~ 32°C
( 62 °F ~ 90°F)
Outdoor
temperature
-15°C ~ 24°C / 5 °F~76°F
Timer indicator
17°C ~ 32°C
( 62 °F ~ 90°F)
-7°C ~ 24°C / 20 °F ~ 76°F 0°C ~ 30°C / 32 °F~86°F
Heating operation
Fig. 5-2
Fig. 5-3
18°C ~ 43°C / 64 °F~109°F
-7°C ~ 43°C / 20 °F~109°F
18°C ~ 52°C / 64 °F~126°F
18°C ~ 52°C / 64 °F~126°F
Mode
type)
angle.
Temporary button
When cooling
,
Room
temperature
Outdoor
temperature
18°C ~ 43°C / 64 °F~109°F
Drying operation
type)
Operation lamp
,
Table 3-1
MANUAL
Fig. 5-1
MANUAL
Operation lamp
PERFORMANCE
Manual Swing
OPERATION
Auto-swing
automatically.
remote controller.
NOTE
ALARM
5.1
MANUAL
OPERATION TIMER
OFF
3
Symptoms
E3
E8
3
owner’s manual
E2
W ater-level alarm malfunction
Power failure
FORCED COOL
disabled.
2
E1
•
2
owner’s manual
DIS PLAY
DIGITAL TUBE
channel is abnormal
1 FORCED AUTO
Table 8-2
LED 1
MALFU N CT ION & PRO TE CT I ON D EF I N E OPERATION
ALARM
6. MAINTENANCE
CAUTION
supply is off.
controller.
owner’s manual
4
QSDLU-002AEN
Symptoms
changed.
Causes
Solution
"AUTO"
speed.
"DRY"
exhausted.
not come on.
FAN ONLY
FAN mode.
on the display.
twice.
time.
certain time.
pressed.
change.
Fig.6-3
optional fitting).
Other malfunctions.
NO.
DEF./FAN
operation.
and outdoor units.
3.2-10.5KW
1
TIMER
fire may break out.
position.
work well.
Air Inlet
indoor unit.
Table 8-1
the same position.
8.1
CAUTION
8. TROUBLESHOOTING
OPERATION
MANUAL
the air flow.
result.
1
NOTE
owner’s manual
very dirty.
furniture etc.
damage.
9
OUTDOOR UNIT
8
CK
7
1
2
3
4
5
6
inlet or outlet.
E ON
8
E OFF
5
MANUAL
owner’s manual
5
spin.
202000192523
20130925
owner’s manual
6
owner’s manual
7
owner’s manual
8
CONTENTS
3
INDOOR UNIT
PAGE
inlet or outlet.
1
4
AU
TO
CO
OL
DR
AT
K
HOU
R
SPEE
D
FAN
SPE
ED
SW
SW
AIR
RESE
T LOCK
ING
ING
C/H
DIRE
CTIO
TIM
TIM
OWNER'S
N
OK
ECO
CLO
6
CLOC
SET
FAN
DE
TROUBLES..........5
TEM
SE P
T
Y
HE
FAN
MO
M
MAINTENANCE.........................................................................................4
2
8
damage.
damage.
9
OR
wiring regulations.
9
7
8
CAUTION
7
8
to the equipment.
9
WARNING
8
8
8
INDOOR UNIT
Fig.1
OUTDOOR UNIT
7
8
9
Installation part
Connecting pipe
Air inlet
Air outlet
Display panel
maintenance.
Remote controller
Drain pipe
NOTE
or cause a fire.
cooling mode
mode after soon.
does not leak.
CAUTION
works of art.
Fig.6-1
3.2-10.5KW
2
14-16KW
Fig.6-3.
E8
2
channel is abnormal
E1
5
E4
6
E7
noise is heard.
Fig.6-2
Other malfunctions.
8.2
7
EE
8
Ed
9
F3
F4
10
11
operation.
and outdoor units.
change.
Fig.6-3
owner’s manual
5
spin.
owner’s manual
6
Flas hing at 2.5HZ
LED 2
TIMER
Unit does not start
Low cooling effect
Flas hing at 0.5HZ
LED 3
DEF.FAN
LED 4
ALARM
D ISPLAY
DIGITAL TUBE
•
channel is abnormal
•
is abnormal
is abnormal
E2
•
abnormal
E4
•
Outdoor malfunction
E6
•
E5
•
EEPROM malfunction
E7
•
E8
•
EC
•
Eb
•
Ed
•
Light
3
MANUAL
OPERATION TIMER
DEF./FAN
TIMER
DEF./FAN
ALARM
Timer indicator
type)
Temperature
OPERATION TIMER
DEF./FAN
Mode
ALARM
Alarm indicator
Temporary button
Cooling operation
Heating operation
Operation lamp
Temperature
Cooling operation
MANUAL
Timer indicator
Alarm indicator
Alarm indicator
17°C ~ 32°C
( 62 °F ~ 90°F)
-7°C ~ 24°C / 20 °F ~ 76°F 0°C ~ 30°C / 32 °F~86°F
your body.
Room
temperature
0°C ~ 50°C / 32 °F~122°F
-15°C ~ 50°C / 5 °F~122°F
-15°C ~ 24°C / 5 °F~76°F
Drying operation
0°C ~ 50°C / 32 °F~122°F
1
2
3
Solution
Power failure.
Replace.
controller.
compressor.
Wait.
of
refrigerant.
Install manostat.
exchanger is dirty.
blocked.
refrigerant.
smooth.
sunshine.
Reduce heat source.
refrigerant.
closed.
lack of
refrigerant.
Use heating device.
refrigerant.
Fig. 5-2
When heating
5.2
Auto-swing
automatically.
Fig. 5-4
17°C ~ 32°C
( 62 °F ~ 90°F)
0°C ~ 30°C / 32 °F~86°F
17°C ~ 32°C
( 62 °F ~ 90°F)
NOTE
Causes
17°C ~ 32°C
( 62 °F ~ 90°F)
Outdoor
temperature
Heating operation
Timer indicator
angle.
Fig. 5-3
18°C ~ 43°C / 64 °F~109°F
-7°C ~ 43°C / 20 °F~109°F
18°C ~ 52°C / 64 °F~126°F
18°C ~ 52°C / 64 °F~126°F
Mode
type)
Temporary button
When cooling
,
Room
temperature
18°C ~ 43°C / 64 °F~109°F
Drying operation
type)
Operation lamp
,
Outdoor
temperature
Fig. 5-1
Table 3-1
MANUAL
Operation lamp
MANUAL
Manual Swing
PERFORMANCE
Auto-swing
automatically.
remote controller.
OPERATION
5.1
NOTE
ALARM
MANUAL
Power failure
OFF
Table 8-3
Symptoms
Table 8-1b
LED 1
OPERATION
3
FORCED COOL
disabled.
owner’s manual
Low heating effect
NO.
2
2
EC
Light
1
1
E3
1 FORCED AUTO
owner’s manual
D ISPLAY
DIGITAL TUBE
optional fitting).
LED 4
ALARM
4
LED 3
DEF.FAN
LED 2
TIMER
position.
LED 1
OPERATION
E2
ALARM
Table 8-2
channel is abnormal
Air filter
NO.
DEF./FAN
the outdoor unit.
3
erson
work well.
Air Inlet
TIMER
fire may break out.
Table 8-1a
indoor unit.
unit.
the same position.
8.1
CAUTION
8. TROUBLESHOOTING
OPERATION
MANUAL
the air flow.
result.
1
NOTE
owner’s manual
very dirty.
furniture etc.
WARNING
OUTDOOR UNIT
1
2
3
4
5
6
CK
7
E ON
8
E OFF
5
MANUAL
6. MAINTENANCE
CAUTION
supply is off.
controller.
owner’s manual
4
QSDLU-002AEN
Symptoms
changed.
Causes
Solution
"AUTO"
speed.
"DRY"
exhausted.
not come on.
FAN ONLY
FAN mode.
on the display.
twice.
time.
certain time.
pressed.
E1
E3
Flas hing at 5HZ
202000192523
20130925
Flas hing at 1HZ
owner’s manual
7
owner’s manual
8
CONTENTS
3
INDOOR UNIT
PAGE
inlet or outlet.
1
4
AU
TO
CO
OL
DR
AT
K
HOU
R
SPEE
D
FAN
SPE
ED
SW
SW
AIR
RESE
T LOCK
ING
ING
C/H
DIRE
CTIO
TIM
TIM
OWNER'S
N
OK
ECO
CLO
6
CLOC
SET
FAN
DE
TROUBLES..........5
TEM
SE P
T
Y
HE
FAN
MO
M
MAINTENANCE.........................................................................................4
2
8
damage.
damage.
9
OR
wiring regulations.
9
7
8
CAUTION
7
8
to the equipment.
9
WARNING
8
8
8
INDOOR UNIT
Fig.1
OUTDOOR UNIT
7
8
9
Installation part
Connecting pipe
Air inlet
Air outlet
Display panel
maintenance.
Remote controller
Drain pipe
NOTE
or cause a fire.
cooling mode
mode after soon.
does not leak.
CAUTION
works of art.
Fig.6-1
3.2-10.5KW
2
14-16KW
Fig.6-3.
E8
2
channel is abnormal
E1
5
E4
6
E7
noise is heard.
Fig.6-2
Other malfunctions.
8.2
7
EE
8
Ed
9
F3
F4
10
11
operation.
and outdoor units.
change.
Fig.6-3
owner’s manual
5
spin.
owner’s manual
6
Flas hing at 2.5HZ
LED 2
TIMER
Unit does not start
Low cooling effect
Flas hing at 0.5HZ
LED 3
DEF.FAN
LED 4
ALARM
D ISPLAY
DIGITAL TUBE
•
channel is abnormal
•
is abnormal
is abnormal
E2
•
abnormal
E4
•
Outdoor malfunction
E6
•
E5
•
EEPROM malfunction
E7
•
E8
•
EC
•
Eb
•
Ed
•
Light
3
MANUAL
OPERATION TIMER
DEF./FAN
TIMER
DEF./FAN
ALARM
Timer indicator
type)
Temperature
OPERATION TIMER
DEF./FAN
Mode
ALARM
Alarm indicator
Temporary button
Cooling operation
Heating operation
Operation lamp
Temperature
Cooling operation
MANUAL
Timer indicator
Alarm indicator
Alarm indicator
17°C ~ 32°C
( 62 °F ~ 90°F)
-7°C ~ 24°C / 20 °F ~ 76°F 0°C ~ 30°C / 32 °F~86°F
your body.
Room
temperature
0°C ~ 50°C / 32 °F~122°F
-15°C ~ 50°C / 5 °F~122°F
-15°C ~ 24°C / 5 °F~76°F
Drying operation
0°C ~ 50°C / 32 °F~122°F
1
2
3
Solution
Power failure.
Replace.
controller.
compressor.
Wait.
of
refrigerant.
Install manostat.
exchanger is dirty.
blocked.
refrigerant.
smooth.
sunshine.
Reduce heat source.
refrigerant.
closed.
lack of
refrigerant.
Use heating device.
refrigerant.
Fig. 5-2
When heating
5.2
Auto-swing
automatically.
Fig. 5-4
17°C ~ 32°C
( 62 °F ~ 90°F)
0°C ~ 30°C / 32 °F~86°F
17°C ~ 32°C
( 62 °F ~ 90°F)
NOTE
Causes
17°C ~ 32°C
( 62 °F ~ 90°F)
Outdoor
temperature
Heating operation
Timer indicator
angle.
Fig. 5-3
18°C ~ 43°C / 64 °F~109°F
-7°C ~ 43°C / 20 °F~109°F
18°C ~ 52°C / 64 °F~126°F
18°C ~ 52°C / 64 °F~126°F
Mode
type)
Temporary button
When cooling
,
Room
temperature
18°C ~ 43°C / 64 °F~109°F
Drying operation
type)
Operation lamp
,
Outdoor
temperature
Fig. 5-1
Table 3-1
MANUAL
Operation lamp
MANUAL
Manual Swing
PERFORMANCE
Auto-swing
automatically.
remote controller.
OPERATION
5.1
NOTE
ALARM
MANUAL
Power failure
OFF
Table 8-3
Symptoms
Table 8-1b
LED 1
OPERATION
3
FORCED COOL
disabled.
owner’s manual
Low heating effect
NO.
2
2
EC
Light
1
1
E3
1 FORCED AUTO
owner’s manual
D ISPLAY
DIGITAL TUBE
optional fitting).
LED 4
ALARM
4
LED 3
DEF.FAN
LED 2
TIMER
position.
LED 1
OPERATION
E2
ALARM
Table 8-2
channel is abnormal
Air filter
NO.
DEF./FAN
the outdoor unit.
3
erson
work well.
Air Inlet
TIMER
fire may break out.
Table 8-1a
indoor unit.
unit.
the same position.
8.1
CAUTION
8. TROUBLESHOOTING
OPERATION
MANUAL
the air flow.
result.
1
NOTE
owner’s manual
very dirty.
furniture etc.
WARNING
OUTDOOR UNIT
1
2
3
4
5
6
CK
7
E ON
8
E OFF
5
MANUAL
6. MAINTENANCE
CAUTION
supply is off.
controller.
owner’s manual
4
QSDLU-002AEN
Symptoms
changed.
Causes
Solution
"AUTO"
speed.
"DRY"
exhausted.
not come on.
FAN ONLY
FAN mode.
on the display.
twice.
time.
certain time.
pressed.
E1
E3
Flas hing at 5HZ
202000192523
20130925
Flas hing at 1HZ
owner’s manual
7
owner’s manual
8
NOTE CONCERNING PROTECTION OF ENVIRONMENT
This product must not be disposed of via normal household waste after its service life, but
must be taken to a collection station for the recycling of electrical and electronic devices. The
symbol on the product, the operating instructions or the packaging indicate such disposal
procedures. The materials are recyclable in accordance with their respective symbols. By
means of re-use, material recycling or any other form of recycling old appliances you are
making an important contribution to the protection of our environment. Please ask your local council where
your nearest disposal station is located.
INFORMATION CONCERNING USED REFRIGERANT MEDIUM
This unit is containing fluorinated gases included in the Kyoto protocol. The maintanance and the liquidation
must be carried out by qualified personel.
Type of refrigerant: R410A
The composition of the cooling medium R410A: (50% HFC-32, 50% HFC-125)
The quantity of the refrigerant: please see the unit label.
The value GWP: 2088
GWP = Global Warming Potential
In case of quality problem or other please contact your local supplier or authorized service center.
Emergency number: 112
PRODUCER
Producer: SINCLAIR CORPORATION Ltd., 1-4 Argyll St., London W1F 7LD, UK, www.sinclair-eu.com
This product was manufactured in China (Made in China).
REPRESENTATIVE AND TECHNICAL SUPPORT
NEPA spol. s r.o.
Purkyňova 45
612 00 Brno
Czech Republic
Tel.: +420 800 100 285
www.nepa.cz

user manual

Transcription

Similar documents

High Pressure Misting Fans

CLIMATIZADOR SPLIT MURAL AIR CONDITIONER SPLIT WALL

AF8000E AF10000E manual

case study - Adknowledge

Instruction Manual

Prelude 9x12 HS Cover

document - GeoComfort Geothermal Systems

0701-Climatouch INFO Sheets BMP+OUT.indd

Product catalogue teco cs 230

Compact Horizontal Packaged Unit