Scotch Advanced Tape Glider Operating Instructions
[email protected] Advanced Tape Glider Refill Rolls
Acid Free -lqinch x 36 yd
General Purpose -lqinchx 36 yd
Applies adhesive while removing/rewinding liner.
Press latch "A' and lift to open cover.
Hold rewind wheel "B", rotate diamond shaped
tape rewind cover "C" counterclockwise and lift
up to remove.
Place tape with liner tab at the bottom
pointing toward the roller "D", Place tape
roll on tape wheel and gently push down
and rotate back and forth until "E" locks
4. Press trigger and hold. Thread the plaid
leader over the ribbed roller "F", under the
smooth roller "G" and over the tape roll to
the rewind wheel hub. Refer to the arrows
in the applicator, Stop when plaid leader
reaches the back rewind wheel and thread
through slots in a "w" pattern. Continue
pressing trigger and rotate rewind wheel
clockwise to bring adhesive forward to the
front roller. Replace tape rewind cover and
5. Rub adhesive back and forlh on the front
roller "G" with thumb until adhesive breaks,
making sure you do not br:eak the liner.
6. To start application: Place (front) roller "H" 0n surlace,
press trigger, and pull glider toward you.
To end application: Keep applying roller on sufface, stop, release
trigger and continue to pull glider toward you to break tape.
To remove rewound liner, rotate and remove diamond shaped tape
rewind cover "J". Remove liner. To remove tape core, push hook
"K" and remove tape core.
Lubrication: All shafts should be periodically lubricated with white
cleaning: Disassemble as required. Remove excess tape from glider using
50/50 isopropyl alcohol and water solution.
Note: Follow the solvent manufacturer's precautions and directions for use
when using solvents.
Re-Loading in the middle of the roll
lf you need to thread a partially used tape roll, first remove approximately
10" 0f adhesive from the tape liner. Then continue to load the glider
according to directions.
U.S.A. ordering information
Replacement parts and part prices
available direct from:
3M Tape Dispenser Pafts
241 Venture Drive
Amery, Wl 54001 -1325
FAX # 71 5/268-81 53
U.S.A. repair service ship direct to:
Tape Equipment Repair Services
241 Venture Drive
Minimum billing on parls orders will be $25.00.
Replacement part prices available on request.
0.00 restocking charge per invoice on returned parts.
U.S.A. Replacement Parts
78-81 1 3-6693-5
78-81 1 3-6609-1
PRODUCT USE STATEMENT
During Warranty Period: Contact your nearest 3M representative or authorized [email protected] ATG Adhesive Applicator distributor.
Product Use: Many factors beyond 3M's control and uniquely within user's knowledge and control can affect the use and pedormance
of a 3M
product in a pafticular application. Given the variety of factors that can affect the use and performance
of a 3M product, user is solely responsible
for evaluating the 3M product and determining whether it is fit for a particular purpose and suitable for user's method of application.
wananty, limited Remedy, and Disclaimer: 3M warrants for g0 days from the date of purchase from a 3M authorized distributor,
[email protected] ATG Adhesive Applicator will be free from defects in material and manufacture. 3M MAKES N0 oTHER
WARRANTTES 0R coNDlTtoNS,
EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANry OR CONDITION
OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE OR ANY IMPLIED WARRANTY OR CONDITION ARISING OUT OF A COURSE OF DEALING,
CUSTOM OR USAGE OF TRADE. If thc
3M product does not conform to this warranty, then the sole and exclusive remedy is, at 3M's option, replacement of the 3M product
or refund of
the purchase price.
Limitation of Liability: Except where prohibited by law, 3M will not be liable for any loss or damage arising from the 3M product, whether direct,
indirect, special, incidental or consequential, regardless of the legal theory asserted, including warranty, contract, negligence or strict liability.
3M lndustrial Adhesives and Tapes Division
SL Paul, MN
3M and Scotch are trademarks of 3M Company.
Glider Made in China.
Tape Made in U.S.A. with Globally Sourced Materials.