Product catalog air regulation control equiPment

Transcription

®
A ir R egulation
C ontrol
E quipment
Product
C ata l o g
®
TABLE OF CONTENTS
UNIVERSAL STANDOFF REGULATORS............................................2
DURO-TWIST REGULATORS.............................................................2
STANDOFF REGULATORS.............................................................3-4
QUADLINE DAMPER QUADRANTS...............................................4-5
SPEC-SEAL™ UNIVERSAL DAMPER REGULATOR..........................5
UNIVERSAL REGULATOR.................................................................5
SPEC SEAL END BEARING SUPPORT KITS.......................................5
STAMPLINE REGULATORS...............................................................6
SPECLINE REGULATORS & DAMPER PARTS..............................7-8
END BEARINGS................................................................................9
JIFFY DAMPERS................................................................................9
HAMMER ON DAMPER HARDWARE & ACCESSORIES...............10
MULTI-BLADE DAMPER HARDWARE............................................11
BLADE EDGING..............................................................................12
SIDE SEALS....................................................................................12
MULTI-BLADE DAMPER PARTS...............................................12-13
ACCESS DOORS.............................................................................14
ACCESS DOOR LOCKING DEVICES...............................................15
GASKETING....................................................................................15
INSTRUMENT TEST PORT..............................................................16
HINGES...........................................................................................16
FIRE DAMPER HARDWARE..............................................................16
HANGING STRAP.............................................................................16
DYN-O-TIES......................................................................................17
DYN-O-TIE GUN...............................................................................17
STAINLESS STEEL DYNA-CLAMPS™............................................18
STAINLESS STEEL PARTS........................................................18-19
UNIVERSAL STANDOFF REGULATORS
The Universal Economy Standoff Regulator from Duro Dyne is a hand operated elevated regulator designed for use with 1/4” or 3/8” square
rod on externally insulated duct. The unique 10 degree foot allows the same regulator to be used on both square or round ductwork,
alleviating the need to stock multiple regulators. It is offered in four standoff heights: 1’’, 1-1/2’’, 2’’ & 3’’. The handle is locked in place with
a heavy duty high torque stamped wing nut and clearly shows damper position with embossed designations for open and closed. Reinforcing
gussets in four locations add to the rigidity of this regulator. An optional
UESO - UNIVERSAL ESO
score and Heto Notch allows the UESO to work for multiple damper fitting
ITEM#
CODE
SHAFT SIZE STAND HEIGHT
applications including Hetos.
Heavy duty, ergonomic
rolled handle
6369
6370
6371
6372
UESO-14-100
UESO-14-150
UESO-14-200
UESO-14-300
1/4” sq.
1/4” sq.
1/4” sq.
1/4” sq.
1”
1-1/2”
2”
3”
6373
6374
6375
6376
UESO-38-100
UESO-38-150
UESO-38-200
UESO-38-300
3/8” sq.
3/8” sq.
3/8” sq.
3/8” sq.
1”
1-1/2”
2”
3”
6377
UESO-12-100
6378
UESO-12-150
6379
UESO-12-200
6380
UESO-12-300
Seal Kits Sold Separately.
1/2” sq.
1/2” sq.
1/2” sq.
1/2” sq.
1”
1-1/2”
2”
3”
Gussets for strength & rigidity
Heto notch
10° universal bend for
square & round duct
Heto cut-away
score line
DURO-TWIST™ REGULATORS
The Duro-Twist is a hand operated elevated regulator designed for use with square rod on both square and round externally insulated duct.
It is offered in four standoff heights: 1’’, 1-1/2’’, 2’’ & 3’’. The Duro-Twist is engineered with a strong friction resistance so it stays set
without any need to lock it in place. The high visibility yellow handle allows it to be easily found in the field on wrapped duct. The handle
position illustrates damper blade position on the outside of the ductwork.
Manual operation
(no tools)
The wing nut has a locking feature molded into
the nut. This secure locked fit eliminates any
movement from duct system vibration.
DURO-TWIST
Four Sizes:
1’’, 1-1/2’’, 2’’, 3’’
10° angled stand to accomodates both
square and round duct
PAGE 2
ITEM#
CODE
SHAFT SIZE
STAND HEIGHT
7071
7072
7073
7075
DT38100B
DT38150B
DT38200B
DT38300B
3/8” sq.
3/8” sq.
3/8” sq.
3/8” sq.
1”
1-1/2”
2”
3”
AIR REGULATION CONTROL EQUIPMENT PRODUCT CATALOG
STANDOFF REGULATORS
STANDOFF WITH STAMPLINE REGULATOR
SRST SQUARE DUCT
1”
1"
1-1/2”
2”
SRST SQUARE DUCT
2-7/8"
2-7/8"
1-7/8"
1-7/8"
2"
1-1/2"
ITEM#
2"
S H
U
N
E
P
TM
OPEN
TM
SQUARE
5-7/8"
5-7/8"
2-7/8"
2-7/8"
1-7/8"
1-7/8"
S H
U
U
N
E
P
TM
TM
DURO DYNE CORP.
H
S
O
N
N
E
N
E
P
U
N
E
P
TM
DYNE
DURO
5-7/8"
1"
1-1/2"
2"
ESO38R-100
3-1/2" 3"
ESO38R-150
ESO38R-200
1/4” sq.
1/4” sq.
1/4” sq.
1”
1-1/2”
2”
3/8” sq.
3/8” sq.
3/8”45° sq.
1”
1-1/2”
2”
NEW YORK-CALIF.-CANADA
7214
1/2” sq.
ESO12R-100
7216
1/2” sq.
ESO12R-150
45°
7218
1/2”
sq.
ESO12R-200
Seal Kits Sold Separately. Packed 10 Per Carton.
"SPECLINE"
ESO ROUND DUCT
U
T
OPEN
S H
"SPECLINE"
3-1/2"
5-7/8"
ESO ROUND
DUCT DUCT
K2 SQUARE
2-7/8"
1"
1-7/8"
KR STANDARD ASSY
T
2-5/16"
1-1/2"
DURO DYNE CORP.
2"
O
P
SEAL FOR STANDOFF WITH ECONOMY HANDLE
U
1"
1-7/8"
1-1/2"
U
KR STANDARD
2-7/8"
T
2-5/16"
N
H
T
KR ROTATED 45° ASSY
S
U
P
O
2"
N
3"
ESO SEAL
FOR USE WITH STAND HEIGHT
7245
SESO-38-214
2-7/8"
Seal is 2-5/16"
always 1/4” larger for tighter seal.
P
E
N
U
T
2”
S
H
O
2-7/8"
CODE
E
S H
ITEM#
P
3-1/2"
DURO DYNE CORP.
2-7/8"
O
U
2-5/16"
T
ASSY
DURO DYNE CORP.
O
3"
S
T
S H
U
2-7/8"
H
K2 SQUARE DUCT
3-1/2"
1”
1-1/2”
2”
S
20°
H
TM
ROUND
E
K2 ROUND DUCT
O
SESO-38-214
DURO DYNE CORP.
1-1/2"
2"
N
1"
1-7/8" 2-7/8"
P
2-7/8"
E
CONCEALED REGULATOR
3-1/2"
2-7/8"
454
K2 ROUND DUCT
S H
2-7/8"
U
S
1"
T
3-1/2"
3"
1-1/2"
2"
CONCEALED REGULATOR
2-7/8"
3-1/2"
P
E
N
1-7/8"
O
S H
2-7/8"
PAGE 3
S
U
T
N
3-1/2"
E
454
U
P
4-3/8"
P
O
O
3"
20°
7208
7210
7212
4-3/8"
CLOSED
N
N
N
454
454
OPEN
ESO14R-100
3-1/2"
ESO14R-1503"
ESO14R-200
E
N
E
E
P
H
N
3"
1-7/8"
DYNE
7/8"2-7/8"
3-1/2" 7/8" 1-7/8"
DURO
1”
1-1/2"
1-1/2”
2"
2”
S H
2-7/8"
7202
7204
7206
CLOSED
1"
45°
ITEM#
SRST ROUND DUCT
T
45°
1-1/2"
ESO SERIES FOR ROUND DUCT
CODE
2"
5-7/8"
ESO SQUARE DUCT
3-3/4"
3-3/4"
1"
1-7/8"
N
S H
S
H
S
N
E
E
P
P
E
P
T
N
E
N
T
1-1/2"
1”
1-1/2”
2”
SRST ROUND DUCT
2-7/8"
2-7/8"
1-7/8"
1"
2"
1”
1-1/2”
2”
TM
5-7/8"
2-7/8"
2-7/8"
3"
3/8” sq.
3/8” sq.
3/8” sq.
"SPECLINE"
OPEN
ESO SQUARE DUCT
3"
1”
1-1/2”
2”
3-1/2"
3"
S
1/4” sq.
1/4” sq.
1/4” sq.
7213
ESO-12-100
1/2” sq.
7215
ESO-12-150
1/2” sq.
7217
ESO-12-200
1/2” sq.
Seal Kits Sold Separately. Packed 10 Per Carton.
4-3/8"
S
2"
DYNE
SQUARE
1"
1-1/2"
ESO-38-100
ESO-38-150
3-1/2" 3"
ESO-38-200
U
DURO
2"
U
S H
TM
CLOSED
CONCEALED REGULATOR
3-1/2"
3-1/2"
U
T
P
CONCEALED REGULATOR
1"
1-1/2"
1"
2"
1-1/2"
3-1/2"
3-1/2"
OPEN
4-3/8"
"SPECLINE"
O
2"
2-7/8"
1-7/8"
P
2-7/8"3-1/2"
3"
2-7/8"
1-1/2"
1-7/8"
7207
7209
7211
DURO DYNE CORP.
CLOSED
1"
K2 ROUND DUCT
P
N
E
DURO DYNE CORP.
O
2-7/8"
2-7/8"
1-7/8"
DYNE
T
ESO-14-100
3-1/2" 3"
ESO-14-150
ESO-14-200
S H
2-7/8"
DURO
U
2-7/8"
1-7/8"
SRST SQUARE DUCT
7201
7203
7205
T
O
2-5/16"
2-5/16"
K2 ROUND DUCT
ITEM#
P
1”
1-1/2”
2"
2”
T
U
1-1/2"
1-1/2"
2"
O
U S H
P
O
1"
3"
1”
1-1/2”
2”
ESO SERIES FOR SQUARE DUCT
CODE
DURO DYNE CORP.
2-7/8"
2-7/8"
3"
1”
1-1/2”
2”
1"
1-7/8"
S
H
2-5/16"
2-5/16"
1-1/2"
1"
2"
1-1/2"
2-7/8"
KR STANDARD ASSY
T
STAND HEIGHT
SRST SQUARE DUCT
KR STANDARD ASSY
T
U
U
E
1"
T
E
3/8” sq.
3/8” sq.
3/8” sq.
STANDOFF WITH ECONOMY HANDLE
T
U
7350
SRST1R-388 w/SRHS-388
7351
SRST1 1/2R-388 w/SRHS-388
7352
Packed 10 Per Carton.
N
E
P
"SPECLINE"
"SPECLINE"
45°
ROUND
2"
S H
1/4” sq.
1/4” sq.
1/4” sq.
DYNE
5-7/8"
5-7/8"
SRST SERIES FOR ROUND DUCT
CODE
SHAFT SIZE
SRST1-1/2R-148 w/SRHS-148
DURO
45°
K2 SQUARE DUCT
S H
7353
7354
7355
3-1/2" 3"
3-1/2" 3"
DYNE
4-3/8"
4-3/8"
2-7/8"
2-7/8"
1-7/8"
ITEM#
DURO
OPEN
K2 SQUARE DUCT
1”
1-1/2”
2”
1"
1”
1-1/2”
2"
2”
T
OPEN
ESO ROUND DUCT
1”
1-1/2”
2”
1-1/2"
1"
2"
1-1/2"
T
S H
CLOSED
CLOSED
ESO ROUND DUCT
STAND HEIGHT
SRST ROUND DUCT
SRST ROUND DUCT
2-7/8"
2-7/8"
1-7/8"
1-7/8"
E
OPEN
ESO SQUARE DUCT
2-7/8"
2-7/8"
1-7/8"
1-7/8"
3/8” sq.
3/8” sq.
3/8” sq.
N
E
P
"SPECLINE"
"SPECLINE"
DYNE
DURO
4-3/8"
4-3/8"
ESO SQUARE DUCT
3" 3-1/2"
3" 3-1/2"
8019
SRST 1-388 w/SRHS-388
8020
SRST 1-1/2-388 w/SRHS-388
8021
DYNE
3-1/2"
3-1/2"
3"
1/4” sq.
1/4” sq.
1/4” sq.
DURO
CLOSED
CLOSED
3"
SRST 1-1/2-148 w/SRHS-148
3-1/2" 3"
3-1/2" 3"
T
2-7/8"
2-7/8"
1-7/8"
1-7/8"
8184
8318
8196
U
T
S H
SRST SERIES FOR SQUARE DUCT
CODE
SHAFT SIZE
1-1/2"
1"
3"
3-3/4"
2-7/8"
N
P
H
S
H
H
S
H
N
E
P
O
H
S
H
N
S
E
N
1/2"
H
2-7/16"
T
DURO DYNE CORP.
O
8304
KR3-1
2-5/16"
8310
KR3-150
2-7/8"
7360
KR3-2
2-7/8"
Packed 101-13/16"
Per Carton.
H
N
S
E
U
T
P
3/8” sq.
3/8” sq.
3/8” sq.
DURO DYNE CORP.
P
P
E
E
N
N
O
N
N
E
P
O
4-11/32"
4-11/32"
TM
TM
DU
TM
TM
QUADLINE DAMPER QUADRANTS
7/8"
"SPECLINE"
7/8"
4-11/32"
0
DURO
DYNE NEW YORK-CALIF.-CANADA
45°
"SPECLINE"
45°
4-11/32"
1”
0
1-1/2”
2”
2-7/8"
0
DURO
"SPECLINE"
DURO
2-7/16"
13/16"
1/2"
"SPECLINE"
2-7/8"
3/8” sq.
3/8”0 sq.
1/2"3/8” sq.
S
PE
P
E
PE
N
N
3"
DURO
3-3/4"
O
2-7/8"
3-3/4”
U
7361
KR3-1R
8366
KR3-150R
7359
KR3-2R
3-3/4"
3-3/4"
2-7/16"
T
3-1/2"
S
SH
T
U
2-9/16"
ITEM#
3"
U
T
ROUND
SH
Y
KR SERIES FOR ROUND DUCT
1-7/16"
2-3/64"
CODE
SHAFT SIZE
STAND 2-3/64"
HEIGHT
2-7/8"
3-1/2"
N
DU
T
2-9/16"
3-1/2"
S H
1-7/16"
2"
454
U
RO
CONCEALED REGULATOR
1-1/2"
NE
S H
3-1/2"
D
2"
1"
NE
1-7/8"
1"
1-1/2"
DY
1”
1-1/2”
2”
CONCEALED REGULATOR
1”
1-1/2”
2”
K2 ROUND DUCT
RO
454
2-7/8"
E
DUCT
P
3-3/4”
2-7/8"
K2 ROUND
1-13/16"
1-7/8"
2-7/16"
KR2-7/8"
SERIES FOR SQUARE DUCT
CODE
SHAFT SIZE
STAND HEIGHT
S
U
E
U
KR STANDARD ASSY
DURO DYNE CORP.
2-5/16"
ITEM#
4-1/16"
2-7/8"
DU
N
E
P
DU
N
E
P
O
N
S
E
P
S
U
S H
N
S H
2-1/2"
3-3/16"
S H
U
DURO-DYNE
N
454
E
N
U
E
E
P
E
N
T
P
S H
E
P
P
N
N
DURO-DYNE
E
454
7/8"
O
O
3-1/2"
DY
NE
NE
U
P
13/16"
2-7/8"3"
2-7/8"
RO
DURO DYNE CORP.
2-5/16"
2"
3"
T
1-13/16"
KR Series available
in stainless steel. See page 18.
2-7/8"
1-1/2"
T
1”
1-1/2”
2”
1-7/16"
7/8"
KR STANDARD ASSY
T
O
3-1/2"
SQUARE
2"
1"
1”
1-1/2”
2”
3-3/4"
U
2-5/16"
1-1/2"
O
3-1/2"
P
2-1/4"
1-7/8"
2-7/8"
TM
45°
1"
K2 SQUARE DUCT
2-7/8"
1/4” sq.
45°
1/4” sq.
1/4”45° sq.
TM
"SPECLINE"
3-3/4"
STANDOFF WITH 3/8’’ DIAL REGULATOR
(FOR DAMPERS UP TO 20”)
1-11/16"
1-5/8"
2-1/4"
2-7/8"
S
5/8"
2-7/8"
1-7/8"
3"
S
DURO
"SPECLINE"
1-5/16" 45°
ESO ROUND DUCT
K2 SQUARE DUCT
1/2"
DYNE
5-7/8"
2-7/8"
K2
SERIES FOR ROUND DUCT
3-1/2"
3-1/2"
CODE
SHAFT SIZE
STAND HEIGHT
DYNE
T
ESO ROUND DUCT
U
DURO
T
2-7/8"
20°
S H
3"
7362
K2-1R
1-13/16"
1"
K2-150R
4-3/8"8197
DY
7363
K2-2R
RO
3-3/4"
Packed 10 Per
Carton.
1-1/16"
5-7/8"
3"
2-7/8"
3-1/2"
3-1/2"
CONCEALED REGULATOR
4-3/8"
3"
U
3-1/2"
20°
U
ITEM#
2"
3-1/2"
S H
2"
1"
1-1/2"
3-1/2"
OPEN
2"
2"
S H
T
U
3-1/2"
1”
1-1/2”
2”
1-1/2"
T
S H
STAND HEIGHT
CONCEALED REGULATOR
1"
1”
1-1/2”
2”
1-1/2"
CLOSED
1-1/16"
1"
1-7/8"
DUCT
CLOSED
OPEN
3"
ROUND
DURO DYNE CORP.
K2 ROUND DUCT
2-7/8"
3-1/2"
1-7/8"
3"
1"
1-1/2"
SRST ROUND DUCT
5/8"
1-7/8"
O
2-7/8"
K2 ROUND
2-7/8"
1-7/8"
2-7/8"
2"
T
U
P
1"
7/8"
5-7/8"
1-7/8"
1-1/2"
1/4” sq.
1/4” sq.
1/4” sq.
SRST ROUND DUCT
O
2-3/8"
SHAFT SIZE
T
U
DURO DYNE CORP.
3/4" 2-7/8"
2"
CODE
2-7/8"
1-11/16"
7364
K2-1
2-5/16"
7365
K2-150
2-1/4"
2-7/8"
7366
K2-2
1-7/8"
2-5/16"
2-7/8"
Packed
10 Per Carton.
2-7/8"
ESO SQUARE DUCT
1-1/2"
1-5/16"
5/8"
K2 2-7/8"
SERIES FOR SQUARE DUCT
KR STANDARD ASSY
DURO DYNE CORP.
ITEM#
1/2"
5-7/8"
3"
ESO SQUARE DUCT
1"
2-5/16"
DURO DYNE CORP.
T
U
P
1-5/8"
2-1/4"
2-1/4"
2-7/8"
1"
O
SQUARE
OPEN
4-3/8"
2"
3"
T
O
2"
1-1/2"
3"
O
3-1/2"
1”
1-1/2”
2”
TM
3/4"
2-5/16"
4-3/8"
2"
1"
CLOSED
O
2-1/2"
T
3-1/2"
OPEN
1-1/2"
TM
3"
3-1/2"
CLOSED
"SPECLINE"
3"
1"
K2 SQUARE DUCT
2-7/8"
3-1/2"
1-7/8"
E
1-7/8"
DURO
"SPECLINE"
2"
3-1/2"
KR STANDARD ASSY
T
U
STANDOFF WITH 1/4’’ DIAL REGULATOR (FOR7/8"
DAMPERS UP TO 10”)
1-1/2"
3"
P
DYNE
N
DYNE
DURO
2-7/8"
1-7/8"
2-7/8"
3-1/2"
U
T
1"
45°
U
S H
E
(CONTINUED)
K2 SQUARE DUCT
2"
1-1/2"
2"
S H
T
2-7/8"
1-7/8"
1"
45°
2"
1"
TM
STANDOFF REGULATORS
1-1/2"
SRST SQUARE DUCT
TM
1-7/8"
5-7/8"
ESO ROUND DUCT
1-1/2"
K-CALIF.-CANADA
4-3/8" 2-7/8"
ESO ROUND DUCT
20°
PECLINE"
1-7/8"
5-7/8"
20°
2-7/8"
4-1/16"
SETS AND PARTS
These heavy gauge plated steel quadrants are designed with excellent handle action as well as quick wing nut adjustment and locking of
the damper. The frame is marked to show the exact position of the damper. For use on square or round ducts.
3/8” QUADRANT SETS (FOR DAMPERS UP TO 20”)
N
0
0
0
5"
A
1 /4
1/ 2
Stands Off Duct
1-1/8”
CODE
8050
KS38
2-3/16"
DUR
US
YNE
O-D
5"
4-5/32"
5-7/8"
1 /4
1/ 2
EN
U
OP
T
1 /4
1/ 2
CODE
80524-5/32"
KS12
Packed 1 Set PerU Carton
T
8060
K5 1/4
Packed 100 per Carton
Stands Off Duct
1-1/8”
PAGE 4
Y
E
2-3/16"
SET CONSISTS OF:
5-5/32" KP-10R round end
K-5 quadrant;
bearing; KP-10S square end bearing
SH
OP
T
SH
EN
A
SH
U
DU
R
1/2’’ QUADRANT SETS
ITEM#
/32"
SET CONSISTS OF:
0
1-5/8"
K-4 quadrant; KP-9R round end bearing;
KP-9S square end bearing
5-7/8"
8051 4-5/32"
KS385
K-4 quadrant; KP-7
spring loc bearing; 4-5/32"
4-11/32"
KP-9S long square end bearing
8049
KS385LU T K-4 quadrant; KP-7L
long spring loc bearOP
1 /4 ing; KP-9L long square end bearing
1/ 2
Packed 1 Set Per Carton
8059
K4
3/8” quadrant only
Packed 100 per Carton
1/2” QUADRANT SETS (FOR DAMPERS UP TO 30”)
2-3/16"
2-3/16"
0
P
O
1/2”
quadrant only
1/ 2
SH
OP
T
ITEM#
SH
SH
EN
TM
TM
TM
TM
U
"SPECLINE"
4-11/32"
DURO
US
YNE
O-D
"SPECLINE"
4-5/32"
4-11/32"
DUR
DURO
"SPECLINE"
DURO
"SPECLINE"
DURO
4-11/32"
2-3/64"
3/8’’
QUADRANT SETS
0
PE
N
T
T
PE
2-3/64"
2-3/16"
EN
2-3/64"
U
EN
SH
YNE
OD
2-9/16"
U
DUR
SH
N
2-9/16"
U
T
1 /4
"SPECLINE"
"SPECLINE"
4-11/32"
4-11/32"
TM
TM
SETS AND PARTS (CONTINUED)
1/2” SHAFT LOC QUADRANT SETS (FOR DAMPERS UP TO 30”)
“Shaft Loc” Quadrants are stamped of heavy gauge steel and clearly indicate the position of the damper. The quadrant handle (available
for either 1/2” square or round shafts) is unique in that it locks the shaft of the damper to it by means of a powerful friction holding device
strong enough to cut into the damper shaft eliminating damper rattle. The shaft is easily locked with 1/2” open end wrench. Available for
square or round
ducts.
2-3/16"
2-3/16"
1/2’’ SHAFT LOC QUADRANT SETS
SH
SH
U
U
OP
T
1 /4
1/ 2
ROUND
T
1 /4
SQUARE
1/ 2
CODE
SHAFT DESCRIPTION
8063
KL7
1/2” square Shaft loc quadrant
8064
KL7R
1/2” round Shaft loc quadrant
Packed 100 Per Carton
EN
4-5/32"
5-7/8"
E
DYN
4-5/32"
ITEM#
5-5/32"
OP
O
DUR
TM
QUADLINE DAMPER QUADRANTS
EN
"SPECLINE"
4-11/32"
Stands Off Duct
1-3/16”
SPEC-SEAL UNIVERSAL REGULATOR & SET
™
The Spec-Seal Universal Regulator Set utilizes a special rubber seal for applicaSelect items available in stainless steel. See page 18.
tions up to 500oF constant temperature. It eliminates leakage and rattle via the
Shaft Loc Mechanism in high pressure systems. The handle’s unique design
utilizes a highly-visible orange plastic cover showing the damper position. This
SPEC-SEAL™
unit, made of heavy-gauge, zinc-plated steel, acITEM#
CODE
BEARING TYPE
commodates four styles of end bearings: 3/8” and
8153
AL38
3/8’’ Square
1/2” with both round or square bearing shafts. It
8154
AL38R
3/8’’ Round
is also available in stainless steel. Individual parts
available upon request.
8158
AL38L
3/8’’ Square Long
Each Set Consists of:
• Regulator
• 2 Rubber Seals
• 2 Metal Washers
• 2 End Bearings
• End Bearing Support
Patent #
7,472,699
Stands Off Duct 7/8”
8152
AL12R
1/2’’ Round
8333
ALN38
3/8’’ Square
8334
ALN38R
3/8’’ Round
8336
ALN12R
1/2’’ Round
Quantity per carton: 10 sets
*8333-8336 DO NOT INCLUDE END BEARINGS
1/ ’’ Round
2
3/ ’’ Square
8
3/ ’’ Round
8
UNIVERSAL REGULATOR
™
•Universal - one regulator for 3/8’’ and 1/2’’; round or square rods.
•Clamp on handle for snug and rattle free fit to bearing or rod.
•Unique “quick set up” handle allows shift from 1/2” to 3/8”
without disassembling the regulator.
•Shaft loc mechanism to eliminate rattle
•High visibility handle; shows damper direction.
•Heavy gauge, zinc plated steel.
•Optional Seal Kit - available for low leakage applications.
•Available in Stainless Steel-quotation upon request.
UNIVERSAL REGULATOR
ITEM#
CODE
DESCRIPTION
8270
MSR03812
3/8 & 1/2” Multisize Regulator Only
8155
SK38
8156
SK12
Quantity per carton: 10
MSRO 3/8” SEAL KIT
MSRO 1/2” SEAL KIT
Patent #
7,472,699
1/ ’’ Square
2
1/ ’’ Round
2
3/ ’’ Square
8
3/ ’’ Round
8
SPEC-SEAL END BEARING SUPPORT KITS
™
ITEM#
8163
8164
8160
8162
SPEC-SEAL™ END BEARING SUPPORT KITS
CODE
BEARING TYPE
EB38
EB38R
EB12
EB12R
3/8” Square Bearing Support Housing
3/8” Round Bearing Support Housing
1/2” Square Bearing Support Housing
1/2” Round Bearing Support Housing
PAGE 5
STAMPLINE REGULATORS
FOR CONTROLLING SMALL DAMPERS
1/4” “JIFFY” REGULATOR SETS (FOR DAMPERS UP TO 10”)
These efficient, low cost, heavy gauge, plated steel regulators install
in a “jiffy” by slipping the washer and handle over the threaded
square end bearing. The wing nut locks the damper in position. The
position of the handle indicates the position of the damper in the
duct. For use on round or square ducts.
Stands Off
Duct 3/4”
ITEM#
CODE
8039
KS7
1/4’’ “JIFFY” REGULATOR SETS
SET CONSISTS OF
KP5 1/4” threaded bearing, handle; KP-6 spring
loc bearing, bevelled wingnut & washer
8046
KS7L
KP5L 1/4” long threaded bearing, handle; KP-6L
long spring loc bearing, bevelled wingnut & washer
Packed 10 Per Carton; 10 cartons per box.
8102
JB1
KP5 1/4” threaded bearing, handle; wingnut &
washer
8220
JB1L
KP5L 1/4” long threaded bearing, handle; wingnut
& washer
8295
JB1XL
KP5XL 1/4” extra long threaded bearing, handle;
wingnut & washer
1/4” DIAL REGULATOR SETS AND BEARINGS (FOR DAMPERS UP TO 10”)
These heavy gauge plated steel regulators are among the most
popular on the market. They minimize air leakage and reduce
rattle. A wing nut locks the damper in position, yet permits quick
readjustment. The dial shows the damper position at a glance. The
regulator mounts easily on round or square ducts.
1/4’’ DIAL REGULATOR SETS
CODE
SET CONSISTS OF
ITEM#
8040
KS14
K-2 regulator; KP-8S square end bearing;
KP-8R round end bearing
8041
KS145
K-2 regulator; KP-6 spring loc bearing;
8047
KS145L
K-2 regulator; KP-6L long spring loc bearing;
KP-8L long square end bearing
7384
KS145XLS K-2 regulator; KP-6 spring loc bearing;
KP-8XL extra long square end bearing
Packed 10 Per Carton; 10 cartons per box.
8056
K2
1/4” regulator only
FOR CONTROLLING LARGER DAMPERS
3/8” DIAL REGULATOR SETS AND END BEARINGS (FOR DAMPERS UP TO 20”)
The following sets and parts are the same as the 1/4” size shown
above except designed for larger dampers. The 3/8” bearings and
regulator are suitable to use on round as well as square duct. Clear
markings on the regulator indicate the damper position which can
be locked securely by a wing nut. The regulator only is also available
in stainless steel - see page 18.
3/8” dial regulator available in stainless steel. See page 18.
3/8’’ DIAL REGULATOR SETS
CODE
SET CONSISTS OF
ITEM#
8044
KSR19
8045
KSR195
8139
KSR195L
7383
KSR195XLS
KR-3 regulator; KP-9R round end bearing;
KR-3 regulator; KP-7 spring loc bearing;
KR-3 regulator; KP-7L long spring loc bearing;
KR-3 regulator; KP-7 spring loc bearing;
KP-9XL extra long square end bearing
8058
KR3
3/8” dial regulator only
3/8” “WEDGE-LOC®” REGULATOR SETS (FOR DAMPERS UP TO 20”)
This attractive rectangular regulator features exclusive “Wedge Loc” action
which firmly locks the bearing to the regulator handle when the damper is
set – preventing rattling. Heavy construction, minimum air leakage and easy
adjustability make this ideal for large dampers in round or square ducts.
PAGE 6 ITEM#
8042
3/8’’ WEDGE ‘LOC’ REGULATOR SETS
CODE
SET CONSISTS OF
KS19
K-3 regulator; KP-9R round end bearing;
8043
KS195
K-3 regulator; KP-7 spring loc bearing;
8048
KS195L K-3 regulator; KP-7L long spring loc bearing;
8057
K3
3/8” wedge loc regulator only
3/8"
RO
DY
5/8"
® 2-1/4"
NE
DU
SPECLINE DAMPER
REGULATORS
1-7/16"
3/4"
MINIMUM LEAKAGE DAMPER REGULATORS
5/8"
1"
Specline Regulators are designed for minimum leakage applications. Each regulator
is comprised of a frame, an indicator handle, a serrated cast alloy core and a cast
alloy nut. Serrations on the cast alloy core mesh
with serrations in the frame to
1-5/16"
1-1/16"
firmly lock the regulator in position. A spring washer situated between the core1"
and
1/2"
5/8"
the cast frame allows for smooth non-binding adjustment. A wedge pin is used to
eliminate
rattle and take up slack between the regulator and the damper shaft.
1/2"
2-1/2"
1-11/16"
3/4"
2-7/16"
1-5/16"
1-1/16"
2-1/4"
5/8"
•All SR and SRH type regulators include a cast alloy frame and2-1/4"
a neoprene frame
2-1/2"
2"
3/4"3/4"
1/2" gasket.
1-11/16"
•The SRHS and SRS
utilize a stamped frame and include a neoprene frame gasket.
2-3/8"
2-1/4"
2" 5/8"
2-1/2"
3-3/16"
SPRING
WASHER
WEDGE
PIN
2-1/2"
3-3/16"
7/8"
NEOPRENE
FRAME
GASKET
SERRATED
CAST ALLOY
CORE
CAST
FRAME
INDICATOR
2-1/4"
3/4"HANDLE
CAST ALLOY
CAP NUT
2-3/8"
5/8"
1-5/8"
0
2-1/4"
0
13/16"
Y
E
2-7/16"
1/2"
1-5/8"
2-1/4"
1/2"
SR-Series
CODE
SHAFT SIZE & NUT
8010
SRH240
1/4” Hex Nut
8012
SRH280
3/8” Hex Nut
8014
SRH220
1-5/16"
1/2”
Hex Nut
8003
SR380
5/8"
3/8” Acorn Nut
8005
1-11/16" SR120
1/2” Acorn Nut
Packed
10 Per Carton
2-1/4"
1/2"
2-7/16"
TM
3-1/2"
HANDLE REGULATOR SET WITH HEX 1-13/16"
NUT AND ACORN NUT
2-3/64"
T
0
0
N
PE
0
1-5/8"
0
DURO
DU
R
E
Y
E
SR-Series
3-3/4"
4-11/32" 13/16"
3/8” Hex Nut
SR148
1/4” Acorn Nut
8002
2-7/16" SR388
8004
TM
2-7/8"
4-1/16"
8022
SRS148
8023
SRS3884-11/32"
3/8” Acorn Nut
8024
SRS128
YNE
OD
EN
E
DYN
0
1/2” Hex Nut
0
1/4” Acorn Nut
1/2” Acorn Nut
PAGE 7
0
TM
3/8” Hex Nut
SRHS128
0
"SPECLINE"
E
DURO
O
Y
OP
8018
4-11/32"
4-11/32"P
DU
R
DUR
EN
SRHS388
1/ 25-5/32"
O
DUR
N
8017
TM
1/ 2
8016
CODE
SHAFT SIZE & NUT
0
0
1-5/8"
2-3/64"
SRHS148
1/4” Hex Nut 2-3/64"
"SPECLINE"
TM
TM
1 /4
5-5/32"
DURO
T
TM
SH
U
"SPECLINE"
SRS-Series
4-11/32"
1 /4
PE
N
PE
N
PE
YNE
OD
DUN R
PE
T
DURO
TM
4-11/32"
4-5/32"
U
"SPECLINE"
U
0
T
SH
"SPECLINE"
"SPECLINE"
EN
SH
HANDLE2-3/64"
SET (STAMPED)
ITEM#
4-5/32" 2-9/16" 0
2-3/16"
DURO
U
DURO
4-11/32"
5-7/8"
1/ 2
OP
1/ 2
OP
DURO
SH
•Stamped Frame U
T
•Heavy Stamped Handle
1 /4
•Solid Die Cast Core
•Hex Nut
1/ 2
SH
0
T
1 /4
TM
TM
4-11/32"
4-5/32"
T
"SPECLINE"
EN
0
5-7/8"2-9/16"
OP
DURO
U
SRHS-Series
U
T
SH
"SPECLINE"
5"
SH
DURO
OP
U
4-5/32" T
2-3/16"
1 /4
Regulator Height2-3/64"
1-3/8”
2-3/64"
EN
SH
T
5"
2-9/16"
EN
Regulator Height 5/8”
2-9/16"
U
3/8” Acorn Nut
1/2"
1/2” Acorn Nut
SR128
Packed
10 Per Carton
2-7/16"
5-5/32"
4-5/32"
HANDLE
STYLE (STAMPED)
2-3/16" REGULATOR SET WITH HEX NUT & ACORN
2-3/16" NUT
SH
DY
SRH228 1-7/16"
1/2” Hex Nut
1/2"
8006
"SPECLINE"
2-3/16"
4-11/32"
TM
TM
2-7/8"
4-11/32"
•Cast
Alloy Body
4-1/16"
•Heavy Stamped Handle
•Hex Nut
•Solid Die Cast Core
0
TM
TM
"SPECLINE"
"SPECLINE"
DURO
13/16"
0
2-7/16"
1/4” Hex Nut
SRH288
8015
N
4-11/32"
1/2"
4-11/32"
Y
SRH248
8013
NE
0
"SPECLINE"
0
DU
R
2-3/64"
DURO
"SPECLINE"
TM
DURO
SRH-Series
2-3/64"
DURO
3-3/4" 4-11/32"
T
1/32"
U
"SPECLINE"
SH
2-3/64"
DURO
2-9/16"
8011
1-5/8"
RO
0
DU
N
0
PE
0
N
0
HANDLE SET CAST
ITEM#
SHAFT SIZE & NUT
1-13/16"CODE 1-7/16"
1-7/16"
U
DY
RO
NE
DU
Regulator Height 1-3/8”
DY
3-1/2"
2-3/64"
RO
NE
SH
2-3/64"
DU
Regulator Height 5/8”
2-9/16"
1-13/16"
N
"SPECLINE"
DURO
DU
R
•Cast Alloy Frame and Body
•Heavy Mounting Gasket
2-7/16"
•Heavy Cast Indicator
Dial
4-11/32"
•Hex
Nut
1-7/16"1/2"
2-1/4"
1-5/8”
1-5/8"
0
ITEM#
1-1/16"
2-1/2"
3-3/16"
DU
DU
0
2-7/16"
SRH-Series
1-11/16"
1-7/16"1/2"
DURO-DYNE
DU
DURO-DYNE
NE
1/2"
1-7/16"
NE
RO
Regulator Height 1-3/8”
1-5/16"
1-13/16"
5/8"
7/8" R O D Y
2-3/64”
2-3/64"
DY
N
2-3/64"
13/16"
Cast Alloy
1-7/16" Gasket
Heavy Mounting
1-13/16"
1"
INDICATOR STYLE CAST
DY
RO
NE
Regulator7/8"
Height 5/8”
DY
RO
NE
DU
1-13/16"
INDICATOR STYLE1-13/16"
REGULATOR SET WITH HEX NUT AND
ACORN NUT
4-
2-3/8"
7/8"
5/8"
1-5/16"
SPECLINE DAMPER REGULATORS
®
DURO-DYNE
(CONTINUED)
1/2"
1-5/8"
90º ANGLE DRIVE DIE CAST MITRE GEAR ASSEMBLY
ITEM#
81355/8" AD38
3/4"
3-1/2"
Packed 5 Per Carton
2-1/4"
1-13/16"
5/8"
DU
DY
RO
NE
5/8"
1-7/16"
CONCEALED STYLE REGULATOR SET WITH HEX NUT
Attractive cast alloy housing with a
corrosion resistant plated cover
1"
1-7/16"
2-7/8"
1/2"
2-3/
N
PE
N
PE
N
PE
DU
N
EN
U
2-1/4"
1 /4
1 /4
1/ 2
OP
EN
1-7/16"
1-7/16"
T
1 /4
1/ 2
E
DYN
T
U
T
OP
1-13/1
DU
EN
EN
U
1/ 2
EN
1 /4
DU
DU
1-11/16"
Y
RO
1-1/16"
4-5/32"
1/ 2
E
DYN
EN
EN
2-1/2"
3-3/16"
DURO-DYNE
DURO-DYNE
EN
1/ 2
OP
T
1 /4
1-5/16"
5/8"
SH
EN
OP
1/ 2
5-7/8"
NE
OP
SH
1 /4
E
NE
DY
NE
RO
SH
1/ 2
1 /4
1"
1/2"
U
U
T
AIR REGULATION CONTROL
EQUIPMENT
CATALOG
1-7/16" PRODUCT
OP
P
UO
T
SH
1 /4
Y
T
BALL JOINT 2-3/16"
2-3/16"
Ball Joint
2-3/16" ITEM#
CODE
SHAFT SIZE
Damper
8032
SRP14
1/4”
Casting3-1/2"
5-5/32"
4-5/32"
8033
SRP516
5/16”
1-13/16"
5-7/8"
1-13/16"
5-5/32"
4-5/32"
Packed 25
Per Carton R O DY
D
4-5/32"
1-13/16"
5-7/8"
5"
A
T
5-7/8"
1-5/8"
0
SH
2-1/4"
1/4”
5/16”
US
YNE
O-D
U
1-5/8"
2-1/4"
1/ 2
3-1/2"
4-5/32"
Cast Alloy
TM
1-11/16"
SHAFT SIZE2-3/16"
DUR
A
OP
SH
US
YNE
RO-D
5"
PAGE 8
OP
SH
SRP40
8035
4-5/32" SRP50
0
5/8" DUR
4-11/32"
1-1/16"
A
8034
2-3/16"
E
"SPECLINE"
Y
7/8"
4-5/32"
5/8"
5"
US
YNE
O-D
CODE
0
1-5/8"
2-1/4"
TM
DUR
SH
ITEM#
0
TM
TM
TM
TM
SPLITTER DAMPER
4-5/32"
0
2-3/16"
1-5/16"
1/2"
U
1-5/8"
1-5/8”
T
2-1/4” 1 /
2-1/4"
4
2-3/64"
BALL JOINT DAMPER
U CASTING
4-11/32"
4-11/32"
1/ 2
4-11/32"
2-3/16"
3/4"
SH
DU
R
OP
1/4” sq.
EN
DU
N
DU
PE
DU
N
5"2-3/8"0
0
N
PE
1/2” sq.
0
TM
N
SB312
DURO
1 /4
"SPECLINE"
"SPECLINE"
TM
4-11/32"
Damper
4-11/32"
Bracket
"SPECLINE"
"SPECLINE"
T
Splitter
DURO
U
DURO
PE
8030
2-3/
DU
"SPECLINE"
3/8” sq.
A
SH
DURO
"SPECLINE"
"SPECLINE"
DURO
DURO
DURO
2-3/16"
0
5/8"0
0
US
YNE
O-D
0
7/8"
4-5/32"
SB338
4-11/32"
0
DURO
DUR
4-5/32"
T
T
T
0
4-11/32"
8028
2-1/2"
0
TM
U
"SPECLINE"
SH
2-3/8"
SPLITTER DAMPER HARDWARE
Steel Bracket, Brass Pivot
4-11/32"
4-11/32"
SB314
2-3/64"
2-3/64"
2"
2-3/64"
2-1/4"
2-3/64"
3/4"
DURO
TM
TM
2-9/16"
U
SPLITTER DAMPER BRACKET
8026
3/4"
T
SH
2-3/16"
sq.
2-3/64"
ITEM#
4-11/32"
0
CLOSED END
CODE
SHAFT SIZE
TM
SB112
3/4"
2-7/16"
0
"SPECLINE"
8029
0
0
2-3/64"
1/2"
1/2"
2-7/16"
0
4-11/32"
DURO
3/8” sq.
2-1/2"
1/2”
1/2"
DY
RO
TM
SB138
"SPECLINE"
8027
DURO
1/4” sq.
NE
SB114
2-3/64"
2-
1-7/16"
T
8025
4-11/32"
1-7/16"
4-11/32"
TM
2-7/16"
"SPECLINE"
SHAFT SIZE
1-7/16"
U
DURO
4-1/16"
CODE
U
4-11/32"
"SPECLINE"
"SPECLINE"
DURO
ITEM#
2-9/16"
Packed 25 Per
Carton
2-9/16"
2"
SH
U
SH
T
2-7/8"
OPEN END
16"
1/2"
U
13/16"
2-7/16"
13/16"
8"
2-9/16"
DY
RO
2-3/64"
1-13/16"
U
NE
NE
DURO
NE
2-9/16"
SH
T
DY
RO
1-13/16"
T
DY
2-9/16"
HU
PE
1-13/16" S
1-7/16"
/4"
2-7/16"
CLOSED END BEARING CAST ALLOY
2-9/16"
1-13/16" 4-1/16"
SH
1
2-7/16"
13/16"
OPEN END BEARING
3-1/2"CAST ALLOY
2-7/8"
3-3/4"
1
4-1/16"
3-3/4"
RO
DY
2-1/4"
2-1/4"
SPECLINE PARTS AND ACCESSORIES
2"
RO
Packed 5 Per Carton
1-11/16"
1-11/16"
2-1/2"
3-3/16"
8008
1/4” sq.
2-7/16" 3/8” sq.
SRC380
DU
8"
4"
13/16"
SHAFT SIZE1-13/16"
1/2"
N
DURO-DYNE
1/2"
1-5/8"
2-1/4"
5/8"
DY
RO
CODE
8007 1-1/16"
SRC140
NE
1/2"
1-1/16" 5/8"
1-5/16"
NE
DURO-DYNE
1-5/16"
ITEM#
1-13/16"
3-3/4"
2-1/2"
3-3/16"
7/8"
7/8"
1"
CONCEALED
DU
3-1/2"
1"
Mitre Gear
Assembly
URO
2-3/8"
1-11/16"
2-1/4"
1-5/8"
2-1/4"
3/4"
2-1/4"
2"
2-3/8"
1/2"
DU
DURO-DYNE
2-1/2"Will accommodate 3/8”
square rod from duct
3/4"
2-1/2"
1-11/16"
2-1/4"
90º ANGLE DRIVE
1-5/16"
1-1/16"
CODE
DESCRIPTION
2-1/4"
7/8"
5/8"
RO
END BEARINGS
(PACKED 100 PER CARTON)
Select items available in stainless steel. See page 19.
ITEM#
SPRING LOC
CODE
APPROX. DIM.
ITEM#
1/4” SQUARE THREADED
CODE
APPROX. DIM.
ITEM#
3/8” SQUARE
CODE
APPROX. DIM.
ITEM#
SPRING LOC LONG
CODE
APPROX. DIM.
ITEM#
1/4” SQUARE
CODE
APPROX. DIM.
ITEM#
1/2” SQUARE
CODE
APPROX. DIM.
ITEM#
ROUND
CODE
APPROX. DIM.
8065
8066
8241
8242
8067
8070
8073
KP6
KP7
KP6L
KP7L
KP8R
KP9R
KP10R
8075
8076
8079
1/4’’ x 2’’
3/8’’ x 2-11/16’’
8068
8069
8077
1/4’’ x 3-1/4’’
3/8’’ x 3-3/4’’
KP5
KP5L
KP5XL
KP8S
KP8L
KP8XL
1/4’’ x 1-1/8’’
1/4’’ x 2-1/8’’
1/4’’ x 3-1/8’’
Spring Loc Example
KP6 #8065:
A ITEM# APPROX. DIM.
1/4’’ x 1-1/8’’
3/8’’ x 1-1/8’’
1/2’’ x 1-1/4’’
8071
8072
8247
1/4’’ x 1-1/8’’
1/4’’ x 2-1/8’’
1/4’’ x 3-1/8’’
KP9S
KP9L
KP9XL
8074
8179
KP10S
KP10L
3-1/8”
2-5/8”
A ITEM# APPROX. DIM.
8065 1/4’’(A) x 2’’(B)
B
The “JDS” Series Jiffy Damper offers the contractor
a quality round damper at a cost lower than
most shop-made dampers. The Duro Dyne JDS
13/16”
series utilizes quality Rapit Spring and Rapit Solid
End Bearing sets. (Packed 10 per carton only.)
1-13/16”
JDS
2-7/8”
3-1/8”
2-5/8”
The “JD” Series Jiffy Damper offers added economy
in those applications where a supporting solid
tail bearing is not required on the damper. The
Duro Dyne JD Damper utilizes one Rapit Spring
End Bearing. (Packed 10 per carton only.)
JD
3-1/8”
2-5/8”
JDEH
HDJD
1/2’’ x 1-1/4’’
1/2’’ x 2-1/4’’
Square Example
KP8S #8068:
8068 1/4’’(A) x 1-1/8’’(B)
B
JIFFY DAMPERS
2-7/8”
3/8’’ x 1-1/8’’
3/8’’ x 2-1/8’’
3/8’’ x 3-1/8’’
The “JDEH & JDE” Series Jiffy Damper offers
an inexpensive alternative for low pressure
applications. The Duro Dyne Economy Damper
utilizes one threaded stud as a support
bearing. Available with handle (JDEH) or
without (JDE). (Packed 100 per carton only.)
The Heavy Duty Jiffy Damper (HDJD) offers
an economical alternative to in shop damper
fabrication. It is manufactured of 22 gauge
galvanized steel blades and comes preassembled. The 3/8’’ square rod extends
3 inches beyond the blade. The HDJD is
compatible with Duro Dyne’s ESO damper
regulator assembly. (Packed 10 per carton only.)
ITEM#
JIFFY DAMPERS
CODE FOR DUCT SIZE DIA.
8092
8093
8094
8095
8096
8097
8137
7153
JDS4
JDS5
JDS6
JDS7
JDS8
JDS9
JDS10
JDS12B
4”
5”
6”
7”
8”
9”
10”
12”
8098
8099
8100
8101
8146
8231
8140
JD4
JD5
JD6
JD7
JD8
JD9
JD10
4”
5”
6”
7”
8”
9”
10”
7111
*JDE6
6”
7120 **JDE6H
6”
*JDE and JDEH series dampers available
in other sizes
**JDEH series dampers contain handles
7077
HDJD4
4”
7078
HDJD5
5”
7163
HDJD6
6”
7164
HDJD7
7”
7165
HDJD8
8”
7166
HDJD9
9”
7167 HDJD10
10”
7168 HDJD12
12”
7169 HDJD14
14”
7170 HDJD16
16”
HDJD Dampers are also sold
unassembled
PAGE 9
HAMMER ON DAMPER HARDWARE & ACCESSORIES
‘RAPIT’® DAMPER REGULATOR
Note: Not recommended for use
in systems over 300 o F.
The RAPIT is an inexpensive, rattle-free regulator for quick installation on balance
or splitter dampers. It is formed from rust-resistant, heavy gauge, galvanized
steel and installs in seconds. The Rapit will penetrate and secure to round
or rectangular damper blades up to 24 gauge steel. It has a fully retractable
bearing of zinc alloy, threaded to accept a 5/16-18 wing nut and a handle that
indicates the damper position. It’s as easy to use as 1-2-3.
1. Slip the bearing over the edge of the damper at the bearing line.
2. Lay the assembly on any firm surface and rap the prong with a hammer.
One blow drives the prong through the damper blade, holding it securely
to the damper.
3. When hit with a hammer, the prong will automatically form up tight by
the anvil, which is built into the bottom of the “Rapit” Bearing.
RAPIT REGULATOR SETS
ITEM#
CODE
8087
8086
8085
8233
RB56
RS156
RS256
RS356
CONSISTS OF:
1 RB-50 Rapit spring bearing; 1 RP-3 washer; 1 RP-2 wing nut
1 RB-50 Rapit spring bearing; 1 RP-3 washer; 1 RP-1 handle; 1 RP-2 wing nut
2 RB-50 Rapit spring bearings; 1 RP-3 washer; 1 RP-1 handle; 1 RP-2 wing nut
1 RB-50 Rapit spring bearing; 1 RB-25T threaded Rapit solid bearing; 1 RP-3 washer; 1 RP-1 handle; 1 RP-2 wing nut
SLIDE RAPIT EXTENSION
The Slide Rapit Extension provides a fast method for extending
the length of a rapit spring end bearing 2’’. There is no need for
tools; just twist the extension fork over the threaded bearing and
slip the sleeve over the joint. Slide Rapit Extensions can also be
combined to accommodate liner thicker than 2’’.
Patent #
8,356,796
SLIDE RAPIT EXTENSION
CODE
DESCRIPTION
ITEM#
7378
SRE516-516
5/16” Slide Rapit Extension
7308
SRE14-14
1/4” Slide Rapit Extension
RAPIT REGULATOR PARTS
RB50
Bearing
RP1
Handle
RP3
Washer
RP3-50NEO
RB25T
Bearing
RP1T
Handle
REC14
RP3-25NEO
ITEM#
ECONO-STUD - ECONOMY
DAMPER HARDWARE
RAPIT REGULATOR PARTS
CODE
DESCRIPTION
8088
RB50
Rapit spring bearing
8201
RB25T
Threaded Rapit solid bearing
8089
RP1
Rapit handle
8198
RP1T
Rapit handle for RB-25T threaded bearing
8090
RP2
Rapit wing nut
8091
RP3
Rapit washer
7190
RP3-50NEO
RB50 washer with neoprene
7191
RP3-25NEO
RB25 washer with neoprene
7388
REC14
1/4” Square Rapit Extension 2-3/4” long
8344
RP2S
5/16-18 Tapered Wing Nut
7349
RP2E
5/16-18 Stamped Wing Nut
Packed 100 per carton* (*7388 packed 10 per carton)
RP2
Wing Nut
PAGE 10
RP2E
Wing Nut
Two combined Slide
Rapit extensions
2” extension
Bulk packing also available
ECONOMY DAMPER HARDWARE
ITEM#
CODE
DESCRIPTION
7031
ES14
7033
ES14W
7035 ES14NW-NEO
8089
RP1
1/4”
Econo-Stud
1/4-20 Stamped
Wing Nut
1/4” Washer with
Neoprene
Rapit handle
MULTI-BLADE DAMPER HARDWARE
NEVA-BIND™ DURO BLADE KIT
FOR PARALLEL DAMPERS
Duro Dyne’s “NEVA-BIND” Linkage Bracket will always align itself to
assure smooth, non-binding operation even on the heaviest damper
blades. Above, or at unequal distance from the blade axis, it is
capable of adjusting itself all four ways, in-out, up-down, sideways
and rotation. Each carton contains all necessary hardware for one
blade of a parallel multi-blade damper.
PARALLEL
ITEM#
CODE
BEARING SIZE
2002
BK2
1/2” ID.
OPAX® BLADE KIT
OPPOSED
FOR OPPOSED ACTION DAMPERS
Opposed Action Dampers minimize turbulence and the control of
the air is more linear. Neva-Bind, 4 way self-adjustability which
Duro Dyne “OPAX” kits feature, automatically compensates for any
construction inaccuracies as well as maintaining linear operation
and critical dimensions between linkage points. “OPAX” provides
opposed action of damper blades and holds the blades rigidly in
position eliminating rattle or flutter. These linkage kits contain all
the necessary hardware for two opposed action damper blades.
ITEM#
CODE
BEARING SIZE
2003
BKO3
7/16” ID.
2004
BKO4
1/2” ID.
DAMPER ASSEMBLY UTILIZING SHOP MATERIALS
A. MAKING THE FRAME
(Same for both parallel and opposed dampers)
1. Cut a piece of channel for the frame 1/4” less
than the duct size, for clearance.
2. SIDE FRAME:
a. Mark off 5/16” from each end.
b. Divide the section inside these marks into as
many parts as there are blades required.
c. Mark for each pivot at the center of each
blade section (b).
d. Drill or punch a 5/8” hole at each pivot (c).
Insert self-oiling bushings (tap fit).
3. Weld the sides and bottoms of the frames. Be
sure to keep them square.
4. On large frames weld on corner braces to keep
the frame square. Place any braces on the side
of the frame which will not interfere with blade
movement. Attach top and bottom end stops, if
required. Cement felt, if required, with insulation
adhesive.
C. MOUNTING THE HARDWARE
“OPAX” HARDWARE
SIDE FRAME
a
3/16”
b
c
b
c
Attach the brackets as shown in drawing “B”. (Always drive a “lo” blade, never a “hi” blade.)
Bushing
7/16” I.D.– BKP-9
or
1/2” I.D.– BKP-10
DImension Distance
“B”
“C”
b
c
b
c
a
Hi
Lo
3/16”
CL
135O
”
1/2
1/2
”
END STOP
Distance C from center of “V” in
blade to center of mounting holes
on LO bracket. (Scribe mark on
bracket).
Blade
Felt
PARALLEL DAMPER
Corner Braces
1
1 or 2
2
2.CUT:
a. “WIDTH” dimension 3/16” less than the
inside of frame.
b. “HEIGHT” dimension: Allow for approximately 7/8” “shrinkage” due to forming; approximately 1/4” blade overlap; approximately
3/16” end clearance to frame.
1-1/4”
8”
1-5/16”
9”
1-3/8”
10”
1-3/8”
11”
1-7/16”
12’’
1-1/2”
Lean bracket
here, against
the edge of
the “V”
OPPOSED
DAMPER “B”
“lo”
DURO-BRACKET
D. ASSEMBLING THE DAMPER
1/4” less than duct
DAMPER BLADE
“Width”
3/16” less than
inside of frame
1/2”
Spaces
1/
2”
2”
1/
o
o
90
90
o
90
2”
1/
3.MARK:
Mark the blades as shown and bend on
the scribe lines.
Strap
BKP-13
2”
to 36’’
to 48’’
to 52’’
C Pin
7/16” x 2-1/2” x BKP-1
or
1/2” x 2-1/2” BKP-5
1/
Required per blade
1-3/16”
7”
“lo”
1/4” less than duct
20
16
12
Width
6”
DURO-BRACKET
Attach the brackets
at the center of
blade.
Channel
Same for both parallel and opposed dampers
1.Material: Gauge Blade Activating Brackets
1’’
PARALLEL HARDWARE
1/2” x 1/2” x 1-1/2” x 1/8”
or
1/2” x 1/2” x 1” x 1/8”
B. MAKING THE BLADES
5”
2”
1/
1/
2”
1. Lay the damper frame flat on the bench.
2. Place the blades inside the frame in the approximate required position (correct overlap, etc.)
3. Place 2 bearing pins in each center blade
groove.
4. Slide the pins under the straps (loosen the setscrews) and into the frame. Tighten the strap
set-screws.
5. Attach all linkage rods.
PAGE 11
BLADE EDGING
DAMPER BLADE EDGINGS
Stainless
Steel
Grey
Vinyl
White
Vinyl
ITEM#
CODE
DESCRIPTION
LENGTH
2151
BKDBE2
White Vinyl
6 ft.
2156
BKDBE3
Grey Vinyl
6 ft.
2153
BKDBE-SSE
Stainless Steel
12 ft.
ITEM#
CODE
SIDE SEALS
STAINLESS STEEL SIDE SEALS
BKSS
BKDSE-SSN
BKDSE-SSW
DESCRIPTION
2077
BKSS
Side Seal
2154
BKDSE-SSN
Side Edging 1-1/2”
2155
BKDSE-SSW
Side Edging 2.59”
*For large runs, custom punched designs available upon request
MULTI-BLADE DAMPER PARTS
(All steel parts are Zinc or Cadmium Plated)
ALL PACKED 100 PER CARTON UNLESS NOTED
BLADE BRACKETS
BUSHINGS
STRAPS
BKP13
BKPRB82
BKPRB81
Standard Bracket as
supplied in BK-1 and
BK-2 Parallel Kits.
STANDARD BRACKETS
ITEM#
CODE
ROD SIZE
2005
BKP814
1/4”
2006
BKP856
5/16”
2007
BKP838
3/8”
ITEM#
CODE
DESCRIPTION
2016
BKP13
Strap and set screws
ITEM#
2025
BKP22
HIGH BRACKETS
CODE
DESCRIPTION
2008
BKP22
High Bracket as supplied
in Opax Blade Kits BKO-3
and BKO-4
High Bracket (not NevaBind) with Brass Pivot
& Steel Set Screw (Not
Shown)
BKP23
2268
CODE
2009
2010
PAGE 12
CODE
2269
DESCRIPTION
BKPRB80
BKPRB81
BKPRB82
BKPRB83
1/4” Round ID rubber bushings
1/4” Square ID rubber bushings
3/8” Round ID rubber bushings
3/8” Square ID rubber bushings
DESCRIPTION
BKP71 Self-aligning strap and set
screws. “V” groove does
not deform blade.
BKP10
BKP81
BKP30P
BUSHINGS
ITEM# CODE
BKHS38
2012
HAT BRACKET
ITEM#
CODE
DESCRIPTION
2075
BKHS38
3/8” Hat Bracket 22ga
DYNA-LINK
LOW BRACKETS
ITEM#
2266
BKP82
ITEM#
BKP25
ITEM# CODE
2267
BKP71
SELF ALIGN & SET SCREW
2011
RUBBER BUSHINGS
STANDARD & SET SCREW
BKP814
BKP26
DESCRIPTION
BKP23 Low Bracket and Linkage
Rod as supplied in Opax
Blade Kits
BKP24 Low Bracket (not Neva-Bind)
with Brass Pivot & Steel Set
Screw (Not Shown)
DYNA-LINK
ITEM#
CODE
DESCRIPTION
2136
BKP26
Dyna-Link
DESCRIPTION
2241
Bronze Bushings 7/16” dia. ID. as
supplied in BK-1 Parallel Blade Kits
and BKO-3 Opax Kits.
BKP10 Bronze Bushings 1/2” dia. ID. as
supplied in BK-2 Parallel Blade
Kits and BKO-4 Opax Kits.
BKP80 Plastic Bushing 1/4” dia. ID. is
designed for use with KP6 & KP6L
Spring Loc Bearings Only.
BKP81 Plastic Bushing 1/4” sq. ID.
2242
BKP82
2243
BKP83
Plastic Bushing 3/8” dia. ID. is
designed for use with KP7 & KP7L
Spring Loc Bearings Only.
Plastic Bushing 3/8” sq. ID.
2079
BKP64
Plastic Bushing 1/2” dia. ID.
2244
BKP84
Plastic Bushing 1/2” sq. ID.
2014
BKP14
Ball Bearing Bushing 7/16” ID.
2261
BKP30P
2013
2240
BKP9
Closed flanged ball bearing
bushing 1/2” ID
MULTI-BLADE DAMPER PARTS
(All steel parts are Zinc or Cadmium Plated)
ALL PACKED 100 PER CARTON UNLESS NOTED
ROD COUPLING
(CONTINUED)
SLIDE PINS
BKP3812
17/32”
SRP10
2”
2-1/4”
3/4” dia
15/32”
ROD COUPLING
ITEM#
CODE
DESCRIPTION
8031
SRP10 3/8” Rod Coupling
Sold 12 Per Carton
3/8” Square to 1/2’’
2239 BKP3812 Round
Rod Coupling
Sold 50 Per Carton
With Duro Dyne’s complete line of Damper Slide
Pins, nearly every configuration requirement can
be satisfied. Duro Dyne’s Damper Blade Slide Pin
selection provides a low cost alternative to damper
hardware such as straps, set screws and solid
pins. Installation is as easy as 1-2-3.
1. Punch a hole in the Damper Blade
2. Position a Pin on the Blade
3. Lock the pin in position by tightening 1/4”
hex nut after sliding the pin into the damper
bushing.
Damper Blade
Carriage Bolt
Slip-In Blade Pin
Foam Gasket
Lock Washer
Nut
DBP1A
STANDARD PINS
PIVOT & SET SCREW
BKP36
BKP34
PIVOT
ITEM#
CODE
DESCRIPTION
2135
BKP36
1/4-28 Brass Pivot
Fully Tapped
BKP35
SET SCREW
ITEM#
CODE
DESCRIPTION
2134
BKP35
1/4-28x1/2” Set Screw
BKP1
STANDARD PINS
ITEM# CODE
ITEM#
DESCRIPTION
2094
2067
2017
BKP1
7/16” diameter pin 2-1/2” long
2019
BKP5
1/2” diameter pin 2-1/2” long
2020
BKP6
1/2” diameter pin 6” long
CODE
SLIDE PINS
APPROX. PIN SIZE
DBP1A 7/16” diameter and 1/2” diameter slide pin, 5/8” Length.
DBP1
Damper Blade Pin only
CRANK ARM
CAC212L
RDBP
CRANK ARM
MILLED & DRILLED PINS
BKP116
MILLED & DRILLED PINS
ITEM#
CODE
ITEM#
SLIDE PINS
CODE
APPROX. PIN SIZE
2221
RDBP100A 1/2” Round Pin 1” Long
2222
RDBP150A 1/2” Round Pin 1½” Long
2223
RDBP200A 1/2” Round Pin 2” Long
ITEM#
8185
CODE
CAC212L
DESCRIPTION
1/2” long shaft
CONTROL SWIVEL
DESCRIPTION
2076
BKP116 1/2” diameter, 6” long,
milled and drilled pin
Sold 50 Per Ctn.
2115 BKP113 1/2” diameter, 3 1/2”
long, milled and drilled pin
Sold 100 Per Ctn.
ROUND TO SQUARE PINS
SDBP
ITEM#
DSC516
SLIDE PINS
CODE
APPROX. PIN SIZE
2215 SDBP100A
2216 SDBP150A
2217 SDBP200A
3/8” Sq. Pin 1” Long
3/8” Sq. Pin 1½” Long
3/8” Sq. Pin 2” Long
ITEM#
8186
CONTROL SWIVEL
CODE
DESCRIPTION
DSC516
Fits 1/4’’ & 5/16’’ Rods
BKP7
ROUND TO SQUARE PINS
ITEM#
CODE
2022
BKP4
2023
BKP7
2024
BKP70
Sold 50 Per Ctn.
2063
BKP8
Sold 100 Per Ctn.
ROD CLIPS
KP25
DESCRIPTION
7/16” diameter to 1/2”
square, 6” long
square, 6” long
square, 6” long
square, 4” long
SIDE LINKAGE BRACKET
ROD CLIPS (U-BOLTS)
ITEM#
CODE
DESCRIPTION
8053
KP25
3/8” Damper Rod Clips
8054
KP26
8055
KP27
SDB2N
ITEM#
2116
LINKAGE BRACKET
CODE
DESCRIPTION
SDB2N
3/8” Side Linkage
Bracket Assembly
PAGE 13
ACCESS DOORS
Duro Dyne Access Doors provide convenient access to the inside of ductwork for testing and cleaning purposes. All doors are manufactured
with an integral frame for minimal leakage. They are offered in a variety of sizes and styles for multiple applications including high pressure,
ductboard applications and more.
INSULATED ACCESS DOORS TAB STYLE
The IAD Door has been designed to create an airtight seal utilizing a moisture, oil and grease
resistant neoprene gasketing between the door to the frame and the frame to the duct. The door
panel is constructed out of 24 gauge galvanized steel and is filled with a 1” 1-1/2 lb. fiberglass
insulation (K factor .26+.03@75°F). The frame is 24 gauge galvanized steel with punched steel
tabs along each side, which locks the frame into the ductwork. Smaller frame corner tabs make
installation easy. Double camlock latches are used on doors 14” and larger. 12” and smaller have
one camlock. Special sizes can be fabricated with multiple walls of steel or see-through panels
or Cam-Lock only style.
Standard Sizes: Installation Note: All holes
IAD
Duct Insulation - Outside
should be cut 1-1/8” smaller than the door.
IADC
Gasket
YELLOW LABEL INSULATED ACCESS DOORS TAB STYLE
The YIAD Access Door is similar in specifications to the standard Insulated Access Door but is
manufactured by industrial workers in the sheet metal union.
YIAD
YIADC
INSULATED ACCESS DOORS SELF STICK STYLE
Duro Dyne HSAD & CSAD access doors feature a self stick frame for easy application. Simply size and
cut the hole, peel the release paper off the frame, press the door onto the ductwork and secure with
screws. They are easy to position with no frame ‘dove tails’ to align and bend. Self Stick Access Doors
are manufactured of 24 ga galvanized steel and feature a one inch wide gasketed frame, 1’’ thick
fiberglass insulation. They have been tested to 10’’SP with minimal leakage when properly installed.
NCSAD
NHSAD
YELLOW LABEL INSULATED ACCESS DOORS SELF STICK STYLE
The Yellow Label Self Stick Access Door is similar in specifications to the standard Self Stick Insulated
Access Door, but is manufactured by industrial workers in the sheet metal union.
HSAD
CSAD
IADVP
IADCVP
VISION PANEL INSULATED ACCESS DOORS
Manufactured of 24 ga galvanized steel, a 1” 1-1/2 lb. fiberglass insulation and door to frame
and frame to door gasket Duro Dyne IADVP’s provide an airtight seal with the added convenience
of a vision panel. Square tabs make for an easier and safer installation process. A clear vision
panel allows visual duct inspection effortlessly!
DUCT BOARD ACCESS DOORS
Duro Dyne’s DBD Series Door is an insulated access door specifically designed for quick and easy installation
onto ductboard. Simply cut the appropriate size hole in the duct, remove the release paper from the adhesive
strip on the door, and press the door into position. Complete the installation by pushing the nails provided through
the eight holes in the frame and capping them with the speed nuts, also provided, on the inside of the duct.
DBD
INSULATED ACCESS
DOORS TAB STYLE
YELLOW LABEL
INSULATED ACCESS
DOORS TAB STYLE
INSULATED ACCESS
DOORS SELF STICK
STYLE
YELLOW LABEL
INSULATED
ACCESS DOORS
SELF STICK STYLE
VISION PANEL
INSULATED ACCESS
DOORS
Hinged
(IAD)
Hinged
(YIAD)
Hinged
(NHSAD)
Cam Only
(NCSAD)
Hinged
(HSAD)
Cam Only
(CSAD)
Hinged
(IADVP)
Cam Only
(IADCVP)
Cam Only
(IADC)
Cam Only
(YIADC)
DUCT BOARD
ACCESS
DOORS
(DBD)
6x6
8230
8385
7082
7091
7046
7056
7310
7320
6381
6390
•
8x8
8168
8386
7083
7092
7047
7057
7311
7321
6382
6391
36066
10x10
8169
8387
7084
7093
7048
7058
7312
7322
6383
6392
36067
12x12
8170
8388
7085
7094
7049
7059
7313
7323
6384
6393
•
14x10
8171
8390
•
•
•
•
•
•
•
•
•
14x14
8167
8389
7086
7095
7050
7060
7314
7324
6385
6394
•
16x16
8172
8391
7087
7096
7051
7061
7315
7325
6386
6395
•
18x12
•
•
•
•
7052
7062
7316
7326
•
•
•
18x18
8173
8392
7088
7097
7053
7063
7317
7327
6387
6396
•
20x20
8174
8393
7089
7098
7054
7064
7318
7328
6388
6397
•
24x24
8175
8394
7090
7099
7055
7065
7319
7329
6389
6398
•
Clamshell style access doors are available in the Dyn-O-Mate Catalog.
PAGE 14
ACCESS DOOR LOCKING DEVICES
ACCESS DOORS LOCKING DEVICES
ITEM#
SP-5
SP-10
SP-20
CAM-LOCK
SL-1
A1SF
Cam Lock available in stainless steel. See page 18.
CODE
SHAFT
LENGTH
SHAFT
SIZE
MAXIMUM DOOR
QTY.
THICKNESS
PER CTN.
8105
SP5
2’’
1/4” dia.
1 3/8’’
25
8106
SP10
3’’
3/8” dia.
1 1/2’’
10
8107
SP20
4’’
1/2” dia.
2’’
8138
CAM-LOCK
100
8108
SL1
25
8397
SL2
50
8182
A1SF
100
10
THE DIMENSIONS SHOWN ARE NORMAL AND SUBJECT TO STANDARD MANUFACTURING TOLERANCES.
GASKETING
Wherever flanges are used in connecting parts of a duct system, the potential for air leakage exists. Besides contributing
to energy waste, leaks can also create noise. Sealing of ductwork can be accomplished with the use of gasket which
adheres to flanged surfaces. When this material is attached to a flange, which is then assembled to a second flange, the
material is compressed and fills gaps and irregularities creating a seal.
VINYL FOAM (PVC)
Vinyl Foam is a low density PVC Foam. When this material is attached to a
flange which is then assembled to a second flange, the material is compressed
and fills gaps and irregularities creating a seal.
ITEM#
VINYL FOAM (PVC)
CODE
DESCRIPTION
LENGTH
8123
8124
8125
PVC 1812
PVC 1434
PVC 3834
ITEM#
8126
8127
8128
CODE
UF 312
UF 1434
UF 3834
URETHANE
DESCRIPTION
LENGTH
ITEM#
CODE
NEOPRENE
DESCRIPTION
LENGTH
URETHANE
Urethane Gasket is a 2 lb. Polyester Urethane. When this material is attached to
a flange which is then assembled to a second flange, the material is compressed
and fills gaps and irregularities creating a seal.
NEOPRENE
Neoperene Gasket is a black, continuous, closed cell, medium density rubber
product that has excellent resistance to oil and fuel.
NEOPRENE UL LISTED
Neoperene Gasket is a black, continuous, closed cell, medium density rubber
product that has excellent resistance to oil and fuel. UL Listed #723
8129
8130
8131
8261
8151
8149
ITEM#
6339
6340
6341
6342
6343
6344
DOUBLE SIDED BLACK FOAM TAPE
BF2S18 is a 1/8” thick black closed cell, crosslinked polyethylene foam coated
on both sides with a high performance acrylic based adhesive with a white
kraft liner. Typical applications: circular duct connectors and rectangular duct
connectors.
ITEM#
7198
7197
7199
1/8” x 1/2”
1/4” x 3/4”
3/8” x 3/4”
BN 1812
BN 1434
BN 3834
BN 31634
BN 51634
BN3161
3/16” x 1/2
1/4” x 3/4”
3/8” x 3/4”
1/8” x 1/2”
1/4” x 3/4”
3/8” x 3/4”
3/16” x 3/4”
5/16”x 3/4”
3/16” x 1”
NEOPRENE UL LISTED
CODE
DESCRIPTION
BN1812UL723
BN1434UL723
BN3834UL723
BN31634UL723
BN51634UL723
BN3161UL723
1/8” x 1/2”
1/4” x 3/4”
3/8” x 3/4”
3/16” x 3/4”
5/16” x 3/4”
3/16” x 1”
50’/RL
50’/RL
50’/RL
50’/RL
50’/RL
25’/RL
50’/RL
50’/RL
25’/RL
50’/RL
50’/RL
50’/RL
LENGTH
50’/RL
50’/RL
25’/RL
50’/RL
50’/RL
50’/RL
DOUBLE SIDED BLACK FOAM TAPE
CODE
DESCRIPTION
LENGTH
BF2S18-34
BF2S18-100
BF2S18-112
1/8” x 3/4”
1/8” x 1”
1/8” x 1-1/2”
108’/CTN
108’/CTN
108’/CTN
PAGE 15
INSTRUMENT TEST PORT
/4"
INSTRUMENT TEST PORT
ITEM#
CODE
QTY PER
CARTON
The Instrument Test Port has a durable cast zinc alloy construction with a heavy gauge zinc plated cap.
Its Neoprene Expansion Plug can withstand up to 180°F and has resisted pressures up to 90 PSI when
installed. The TH-1 accommodates 1” of insulating materials and has an inside diameter of 1-1/16”. The
IP-2 accommodates 2” of insulation material and has an inside diameter of 1-1/8”. The IP-4 offers a 3/4’’
diameter access to the air stream. All are designed for high velocity systems. A flat neoprene mounting
gasket is supplied. However, for maximum protection against leakage, we recommend using Quad Seal.
2-1/2"
3/4"
TH-1
IP-2
1"
2-1/2"
3/4"
2"
2"
2-1/2"
3-3/16"
1-5/16"
1-1/16"
5/8"
TH1
IP2
IP4
IP-4
2-1/4"
3/4"
2-1/4"
3/4"
2-3/8"
5/8"
5/8"
PIANO HINGES
ITEM#
HPH116
HPH112
PIANO HINGES
SIZE
CODE
DESCRIPTION
RO
DY
NE
DU
ITEM#
1-7/16"
HH2
HH3
1/2"
1-5/8"
CODE
2-1/4"
1-5/8"
HH2
2-1/4"
DURO-DYNE
1-13/16"
DURO-DYNE
8120
HPH1167/8"
1-1/16” x 3’
8121
HPH112
1-1/2” x 3’
7/8"
Packed 25 Per Carton - Special sizes available upon request
BUTT HINGES
25
25
25
2-3/8"
HINGES
1-7/16"
8036
8398
8340
Piano hinge, with holes,
zinc plated
1/2"
1-11/16"
BUTT 1/2"
HINGES
1-11/16"
2-1/4" FINISH
SIZE
DESCRIPTION
2” x 1 - 9/16”
Light, narrow butt hinge,2-1/4"Zinc plated
8109
fast pin, w/ screw holes.
8110
HH3
3” X 2”
Packed 24 Per Carton - Special sizes available upon request
1-5/16"
5/8"1-5/16"
5/8"
Zinc plated
1/2"
FIRE DAMPER HARDWARE
2-7/16"
FLS39
FL43
FL41
FL42
temperature rating 165O
10 pound load
30 pound load
30 pound load
30 pound load
1-13/16"
1-13/16"
DIM.
A D Y DIM. B
RO
1” D 1-1/2”
Y
RO
1-3/4”
2-9/16”1-7/16"
1-3/4”
2-9/16”
1-7/16"
1-3/4”
2-9/16”
DU
2032
2033
2034
2035
FIRE DAMPER HARDWARE
DESCRIPTION
NE
B
All fusible links are listed by
2-3/64"
2-3/64"
Underwriter’s
Laboratories, Inc.
CODE
NE
A
ITEM#
DU
3-1/2"
3-1/2"
HANGING STRAP
1/2"
1/2"
3-3/4"
3-3/4"
1-5/8"
2-7/16"
13/16"
2-7/16"
13/16"
Duro Dyne provides Hanging Strap fabrics that are waterproof, grease, oil 2-7/8"
& acid resistant, and have low smoke & flame development.
-11/32"
4-11/32"
2-7/8"
4-1/16"
HANGING STRAP
Designed for hanging:
4-1/16"
ITEM#
CODE
DESCRIPTION
SIZE
• Flexible Duct
10190
VDS200
Vinyl Duro Strap
1-1/2” x 200’
• PVC Vent Duct
• Duct Board Systems
10179
SVDS300
Single Sided Vinyl Duro Strap
1-1/2” x 300’
• Light Weight Steel
10180
NS300
Nova Strap
1-3/4” x 300’
• Duct Applications
2-9/16"
2-9/16"
2-3/64"
2-9/16" S HU VINYL DURO STRAP2-9/16" S HU
NOVA2-3/64"
STRAP
0
0
0
Y
E
"SPECLINE"
DURO
DU
R
N
0
TM
N
PE
N
PE
N
PE
PE
N
EN
YNE
OD
EN
O
200 F
N/A
4-11/32"
4-11/32"
Black Woven Polypropylene
TM
Black vinyl coated polyester fill
4-11/32"
4-11/32"
.022” Approx.
.025” Approx.
QUANTITY PER CARTON:
10 rolls (Conveniently packaged in a dispenser box with cutting blade)
24 rolls per box
*Product Meets NFPA Class A and UBC Class 1 characteristics of
flame spread less than 25 and smoke development less than 50
when utilizing test method ASTM E-84.
Resistant to Grease, Oil,
Gasoline and Acid.
DUR
1/ 2
TOTAL FABRIC THICKNESS:
ADDITIONAL INFO:
PAGE 16
Fill-11 lbs./In
0
Warp-70 lbs./In.; Fill-70 lbs./In
"SPECLINE"
"SPECLINE"
FABRIC: OP
F
0
TM
DURO
DURO
1 /4
O
0
Less Than 25 / Less
Than0 50
U
TM
T
TM
U
Warp-70 lbs./In. Fill-70 lbs./In
4-11/32"200
Warp8 lbs./In.
4-11/32"
SH
"SPECLINE"
"SPECLINE"
SH
OP
NFPA Class A*
UBC Class 1*
TM
DURO
DURO
TEAR STRENGTH:
"SPECLINE"
"SPECLINE"
5-5/32"
HEAT RESISTANCE:
4-5/32"
TM
DURO
DURO
5-7/8"
U
T
TENSILE STRENGTH:
SH
T
SMOKE DEVELOPMENT:
T
T
2-3/16"FLAME SPREAD &
2-3/16"
2-3/16"
2-3/16"
2-3/16"
DYN-O-TIES
™
Whenever your job calls for securing round flexible duct to outlets, pipes or fittings, you can do the job better, faster, and at a lower cost using
DYN-O-TIES™, flexible duct ties.
No tapes, no screws, no clamps. Position the flexible duct and slip a DYN-O-TIE around the flexible duct over the joint. Draw the DYN-O-TIE
tight with our ratchet action hand tool. A push with the thumb completes the job by clipping off the excess nylon tab for the neatest and
most secure connection you could want. Duro Dyne UV DYN-O-TIES are made to resist Ultraviolet rays and adverse weather conditions
when used in outdoor applications.
DYN-O-TIES, when properly installed, provide secure, self-extinguishing joints when connecting certain types of flexible duct listed by Underwriters
Laboratories Inc., class 1.
NYLON
6/6 V2 – available in five sizes
Self-extinguishing
Fungus inert
o
o
Normal service temp. range: – 40 F to 185 F
Test Results*: Nylon -175 lbs.
NYLON DYN-O-TIES
DESCRIPTION
COLOR LENGTH MAX. DIA. PKG. PKG./CTN
ITEM #
CODE
8322
8312
8323
DN36
DNC36
DN48
7002
UVDN48
7003
UVDN36
8311
8305
7004
7005
DN36
DN48
DN36N
DN48N
Nylon - USA Made
Nylon - USA Made
Nylon - USA Made
UV Resistant Nylon
USA Made
UV Resistant Nylon
USA Made
Nylon - USA Made
Nylon - USA Made
Nylon - Imported
Nylon - Imported
Natural
Natural
Natural
36”
36”
48”
11”
11”
14”
50
100
50
10
5
10
Black
48”
14”
50
10
Black
36”
11”
50
10
Natural
Natural
Natural
Natural
36”
48”
36”
48”
11”
14”
11”
14”
25
25
50
50
20
20
10
10
Non-Metallic
Mechanical
Fastener
181B-C 13ER
MH19757
For use with UL nonmetallic
airducts and air connectors
ITEM #
*Test Method: Tie is secured at both ends forming a
loop. A weight is suspended from the bottom of loop to
determine tensile strength of DYN-O-TIE strap.
CODE
MINI DYN-O-TIES
DESCRIPTION
COLOR
LENGTH
MAX. DIA.
5”
5”
8”
8”
11”
11”
14”
14”
1.38”
1.38”
1.97”
1.97”
2.76”
2.76”
4.02”
4.02”
7043
7042
7018
7020
7022
7024
7026
7028
DNM05M
DNM05UVM
DNM08M
DNM08UVM
DNM11M
DNM11UVM
DNM14M
DNM14UVM
ITEM #
6367
CODE
DESCRIPTION
COLOR
LENGTH
MAX. DIA.
DNMH08M
Nylon
Natural
8”
1.97”
6368
DNMH08UVM
UV Resistant Nylon
Black
8”
1.97”
Nylon
UV Resistant Nylon
Nylon
UV Resistant Nylon
Nylon
UV Resistant Nylon
Nylon
UV Resistant Nylon
Natural
Black
Natural
Black
Natural
Black
Natural
Black
MINI DYN-O-TIES WITH MOUNTING HOLE
DYN-O-TIE GUN INSTALLATION TOOL
The DIT-2 gun is light weight and commonly used to install
most makes of nylon duct ties.
ITEM #
DIT-2
8229
DYN-O-TIE GUN
CODE
DESCRIPTION
DIT2
For use with nylon
PAGE 17
STAINLESS STEEL DYNA-CLAMPS
™
The Dyna-Clamp is an efficient way to secure flex or rigid round duct connections. The stainless steel band can withstand up to 60 PSI, as well
as extreme temperature conditions. The band is secured in place at the bridge by a slotted hex head screw. This zinc plated carbon steel screw
can be flipped up away from the band to offer a quick release when adjustments are needed. Dyna-Clamps are available in stock sizes ranging
from a 7’’ diameter to 20’’. Two or more clamps can also be connected together to accommodate duct diameters over 20’’.
SRST SQUARE DUCT
SRST SQUARE DUCT
2-7/8"
2-7/8"
1-7/8"
1-7/8"
DT7WD
DT8WD
4-3/8"
4-3/8"
Secured
at Bridge
DT10WD
DT12WD
DT15WD
DT16WD
DT18WD
DT20WD
OPEN
ESO SQUARE DUCT
ESO SQUARE DUCT
2-7/8"
2-7/8"
1-7/8"
1-7/8"
1"
1"
1-1/2"
1-1/2"
2"
2"
TM
1-7/8"
1-1/2"
2"
N
E
45°
45°
TM
5-7/8"
5-7/8"
T
3-1/2"
ESO ROUND DUCT
ESO ROUND DUCT
TM
U
20°
20°
3"
3"
"SPECLINE"
"SPECLINE"
STAINLESS STEEL HARDWARE
2-7/8"
1-7/8"
3-1/2"
3-1/2"
NEWNEW
YORK-CALIF.-CANADA
YORK-CALIF.-CANADA
4-3/8"
4-3/8"
S H
2"
2"
DYNE
DYNE
OPEN
OPEN
1"
1"
1-1/2"
1-1/2"
DURO
DURO
3-1/2"
3-1/2"
3"
3"
33”
40”
48.75”
52.5”
57.31”
63.58”
S H
S H U
U
1"
CLOSED
CLOSED
1.75”
1.75”
1.75”
1.75”
1.75”
1.75”
T T
2-7/8"
23.5”
28.25”
10”
SRST ROUND DUCT
SRST ROUND DUCT
2-7/8"
2-7/8"
1-7/8"
1-7/8"
SRST SQUARE DUCT
1.75”
1.75”
12”
15”
16”
18”
20”
N N
E E
P P
Quick Release
Feature
7008
7009
7010
5-7/8"
5-7/8"
7011
7013
7044
OPEN
TM
3-1/2"
3-1/2"
3"
3"
7”
8”
"SPECLINE"
"SPECLINE"
CLOSED
NEWNEW
YORK-CALIF.-CANADA
YORK-CALIF.-CANADA
CLOSED
OVERALL
LENGTH
3"
3"
N N
E E
P P
7012
7007
S H
S H U
U
DYNE
DYNE
2"
2"
CODE
DURO
DURO
1-1/2"
1-1/2"
ITEM #
2"
2"
DYNA-CLAMPS
MAXIMUM
MINIMUM
3-1/2"
3-1/2"
DIAMETER
DIAMETER
T T
2-7/8"
2-7/8"
1-7/8"
1-7/8"
1"
1"
1"
1"
1-1/2"
1-1/2"
3"
P
STANDOFF 3/8” DIAL REGULATOR (FOR DAMPERS UP TO 20”)
DYNE
DURO
KR STANDARD ASSY
KR STANDARD ASSY
300 SERIES FOR SQUARE DUCT
CODE
SHAFT SIZE
STAND HEIGHT
DURO DYNE CORP.
DURO DYNE CORP.
O O
P P
E
N
N
2-7/8"
7290
KR3SS-100
2-7/8"
7292
KR3SS-150
7294
KR3SS-200
2-5/16"
2-5/16"
Packed
10 Per Carton.
3"
3"
S S
H H
S S
H H
U U
T
U T
U
ITEM#
T
T
O O
N
E
P E N
P
SQUARE
3-1/2"
3-1/2"
2-5/16"
2-5/16"
1-1/2"
1-1/2"
TM
EN
1"
1"
1”
1-1/2”
2"
2"
2”
S S
H H
K2 SQUARE DUCT
K2 SQUARE DUCT
2-7/8"
2-7/8"
1-7/8"
1-7/8"
4-3/8"
E
"SPECLINE"
CLOSED
5-7/8"
T
U T
U
DURO DYNE CORP.
3/8” sq.
3/8” sq.
3/8” sq.
1”
1-1/2”
2”
DURO DYNE CORP.
N
N
1"
2-7/8"
2-7/8"
1-1/2"
K2 ROUND DUCT
K2 ROUND DUCT
2"
2-7/8"
2-7/8"
1-7/8"
1-7/8"
CONCEALED REGULATOR
CONCEALED REGULATOR
1"
1”
1"
1-1/2”
2”
2"
2"
1-1/2"
1-1/2"
S H
S H U
U
ITEM#
N
T T
3-1/2"
O
O
4-3/8"
S
2-7/8"
"SPECLINE"
2-7/8"
3-17/16”
2-7/8"
S
7291
KR3SS-100R 2-7/8"
7293
KR3SS-150R
7295
KR3SS-200R
3-3/4"
Packed 10 Per 3-3/4"
Carton.
3"
3"
DYNE
ROUND
3"
DURO
N N
E E P
P P
E
3-1/2"
3-1/2"
454
U
T
CLOSED
300 SERIES FOR ROUND DUCT
CODE
3-1/2"
3-1/2"
454
S H
E
1-7/8"
2-7/8"
1-7/8"
E
2-7/8"
2-7/8"
2-7/8"3-17/16”
O O
P P
SRST ROUND DUCT
SQUARE DUCT
45°
45°
3/8” sq.
3/8” sq.
3/8” sq.
1”
1-1/2”
2”
7/8"
7/8"
TM
45°
5-7/8"
ROUND DUCT
3/8” DIAL REGULATOR (FOR DAMPERS UP TO 20”)
1-1/2"
KR STANDARD ASSY
T
S
U
3-1/4”
2-5/16"
DURO DYNE CORP.
O
2"
ITEM#
CODE
8272
KR3SS
P
E
1"
H
SQUARE DUCT
3/8’’ DIAL REGULATOR
DESCRIPTION
3/8” Stainless Steel dial regulator only
N
2-7/8"
3-3/4”
3"
U
T
S
H
ACCESS DOORS LOCKING2-5/16"
DEVICE
DURO DYNE CORP.
O
P
ACCESS DOORS LOCKING DEVICES
E
N
8"
2-7/8"
2 ROUND DUCT
1-1/2"
PAGE 18
2"
CODE
DESCRIPTION
QTY. PER CTN.
8396
CMLK-SS
Stainless Steel Cam-Lock
100
CONCEALED REGULATOR
3-1/2"
454
1"
ITEM#
S
STAINLESS STEEL HARDWARE
(CONTINUED)
1/2” SPEC SEAL™ UNIVERSAL REGULATOR SET (FOR DAMPERS UP TO 30”)
The Spec-Seal Regulator Set utilizes a special rubber seal for
applications up to 500oF constant temperature. It eliminates
leakage and rattle via the Shaft Loc Mechanism in high pressure
systems. The handle’s unique design utilizes a highly-visible orange
plastic cover showing the damper position. This kit includes 1/2”
square bearing shafts. Individual parts available upon request.
SPEC-SEAL™
ITEM#
CODE
8301
AL12SS
Quantity per carton: 10 sets
BEARING TYPE
1/2’’ Square Stainless
Set Consists of:
• Regulator
• 2 Rubber Seals
• 2 Metal Washers
• 2 End Bearings
• End Bearing Support
Patent #
7,472,699
Stands Off Duct 7/8”
END BEARINGS
(PACKED 10 PER CARTON)
KP9XL-SS
KP10S-SS
3/8” SQUARE
CODE
APPROX. DIM.
ITEM#
7393
KP9XL-SS
3/8” x 3-1/8”
1/2” ROUND
CODE
APPROX. DIM.
7394
7395
KP10S-SS
Spring Loc Example
KP7LSS #7396:
1/2” x 1-1/4”
KP7LSS
KP10R-SS
ITEM#
1/2” SQUARE
CODE
APPROX. DIM.
ITEM#
KP10R-SS
1/2” x 1-1/4”
ITEM#
7396
Square Example
KP10S-SS #7395:
A
B
B
SPRING LOC
CODE
APPROX. DIM.
KP7LSS
A
ITEM# APPROX. DIM.
7396 3/8”(A) x 3-3/4’’(B)
ITEM# APPROX. DIM.
7395 1/2’’(A) x 1-1/4’’(B)
3/8” x 3-3/4”
MULTI-BLADE DAMPER KITS AND PARTS
BLADE KITS
BUSHINGS
BLADE BRACKETS
BKP49SS
BKP52SS
BKP61SS
BUSHINGS
HIGH BRACKETS
BLADE KITS
ITEM#
CODE
DESCRIPTION
2049
BKP52SS
Stainless BKP-22
Stainless BKP-25
ITEM#
CODE
DESCRIPTION
2047
BKP50SS
2057
BKP61SS
Stainless BK-2/Pivot/
Screw Not Neva Bind
2048
BKP51SS Stainless Hi Bracket Only
ITEM#
CODE
DESCRIPTION
2085
BKP49SS
Stainless 1/2” Bushing
STANDARD PINS
BKP63SS
STANDARD PINS
ITEM#
BKP62SS
BKP54SS
CODE
DESCRIPTION
2051 BKP55SS Stainless 1/2” diameter pin
2-1/2” long
2068 BKP63SS Stainless 1/2” diameter pin
6” long
LOW BRACKETS
STRAPS
BKP56SS
STRAP & SET SCREW
ITEM#
CODE
DESCRIPTION
2052
BKP56SS
Stainless Strap/Screw
ITEM#
CODE
DESCRIPTION
2058
BKP54SS
Stainless Low Bracket/
Pivot/Screw
2050
BKP53SS
Stainless Low Bracket
Only
2062
BKP62SS
ROD CLIPS
Stainless Low Bracket/
Pivot/Lollypop
KP25SS
ROD CLIPS (U-BOLTS)
ITEM#
CODE
DESCRIPTION
7397
KP25SS
3/8” Stainless Damper
Rod Clips w/ Nyloc Nut
PAGE 19
Please Visit Our Website
www.durodyne.com
for the most current product information.
®
© Duro Dyne Corp.
Printed in USA 10/12/16
BB008402
Duro Dyne East Division, Bay Shore, NY
631-249-9000 Fax: 631-249-8346
Duro Dyne Midwest Division, Hamilton, OH
513-870-6000 Fax: 513-870-6005
Duro Dyne West Division, Fontana, CA
562-926-1774 Fax: 562-926-5778
Duro Dyne Canada, Lachine, Quebec, Canada
514-422-9760 Fax: 514-636-0328
www.durodyne.com E-mail: [email protected]

Product catalog air regulation control equiPment

Transcription

Similar documents

Duro Dyne Duct Accesories Catalog

rd d4,/.rtr $,Wf*g

Die BUCHSTAVIER - Das Dosierte Leben

Inline-Skate Catalog

View UC

Product catalog air regulation control equiPment

Transcription

Similar documents

Duro Dyne Duct Accesories Catalog

rd d4,/.rtr *$,*Wf*g

Die BUCHSTAVIER - Das Dosierte Leben

Inline-Skate Catalog

View UC

rd d4,/.rtr $,Wf*g