CASED AXIALS - JM AEROFOIL

17
CASED AXIALS - JM AEROFOIL
FEATURES
•
•
•
•
•
•
•
•
315 - 1000 mm diameter
Air flow up to 20.9 m3/s
Static pressures up to 1100 Pa
Fans tested to ISO5801 and BS848
High energy efficiency
Low installed noise levels
Motor protection IP55
Larger sizes available please enquire for more information
ELECTRICAL SUPPLY
220-240V/50Hz/1f
380-420V/50Hz/3f
TEMPERATURE RANGE
00ºC for 2 hours with 3 ph motors on one off emergency
2
operation only.
-40ºC to 50ºC as standard.
50ºC to 70ºC must be run at full speed only.
ErP
COMPLIANT
2015
SIZES
315, 355, 400, 450, 500, 560, 630, 710, 800, 900 and 1000 mm.
IMPELLERS
A unique high efficiency aerofoil section blade with a smoothed
hub and clamp plate for adjustable pitch angle availability.
The Fläkt Woods impellers are all high pressure die cast to
offer thin aerofoil sections for low generation of noise. Every
cast aluminium component is X-ray examined using Real Time
Radiography inspection prior to assembly. The maximum pitch
angles shown allow for speed control by frequency inverter
(3ph only).
MOTORS
All motors are totally enclosed air stream rated class F
insulation. Constructed from aluminium or cast iron as standard
with special ‘T’ slot, or pad mounted fixings. Single speed
motors are suitable for speed control by voltage regulation
where indicated. Three phase motors are suitable for use with
frequency inverters, suitable for turn down to 20% of maximum
speed. Two speed motors are available on request. Suitable
for horizontal or vertical shaft operation. Supplied IP55, with
removable drain plugs.
Sealed for life bearings lubricated with wide temperature range
grease. The BT and CT frames are fitted with overheat protection
thermostat as standard. 80-160 frame motors are fitted with
Thermistor OHP. These motors are suitable for inverter\speed
control down to 20% of full speed and where within scope
incorporate IE2 compliant motors.
Fläkt Woods
9513 GB 2015.08
CASINGS
JM Aerofoil fans are available in either a long cased form, complete
with an externally mounted pre-wired electrical terminal box, or
short cased for duct or plate installation. Casings are spun from
sheet steel with integral pre-drilled and radiused inlet flanges. The
galvanised finish gives a high resistance to corrosion and is ideal
for external as well as internal use.
PRODUCT CODE
63JM/20/4/6/36
•
•
•
•
•
•
63 - denotes the fan impeller diameter in centimetres
JM - denotes fan type
20 - denotes impeller hub diameter in centimetres
4 - denotes a nominal 4 pole speed
6 - denotes the number of blades
36 - denotes the pitch angle for the required duty
ACCESSORIES (Pages 77-82) - CONTROLLERS (Pages 219-267)
Damper
Guard
Bellmouth
Flange
Mounting Feet
Rubber AV’s
Spring AV’s
Flexible
Connector
Silencer
Controls
Transformer
Controls
Electronic
Controls
Inverter
Specifications are subject to alteration without notice
18
JM AEROFOIL PERFORMANCE AND ELECTRICAL DATA
ErP
220-240V/50HZ/1f - L TYPE
COMPLIANT
2015
JM Aerofoil (1 Phase)
PERFORMANCE CHART - 315-630MM
315 - 630 mm
500
400
Static Pressure (Pa)
8
300
7
6
5
200
4
2
100
0
3
1
0
2000
0
4000
0.5
6000
1
1.5
8000
2
10000
2.5
12000
3
14000
m 3/h
m 3/s
3.5
Volume Flow
PERFORMANCE TABLE - 315-630MM
Ref
m3/s @ Pa (Static)
Ref
0
50
1
31JM/16/4/5/34
0.59
0.48
100
150
200
2
35JM/16/4/5/22
0.63
0.53
0.37
3
40JM/16/4/5/40
1.5
1.31
1.07
4
45JM/16/4/5/30
1.82
1.62
1.4
5
50JM/20/4/6/20
1.84
1.68
1.52
1.3
6
50JM/20/4/6/32
2.61
2.41
2.19
1.94
1.62
7
56JM/20/4/6/30
3.64
3.41
3.16
2.89
2.57
8
63JM/20/4/6/16
3.17
3.01
2.82
2.61
2.38
250
300
1.99
1.33
1.12
PRODUCT AND ELECTRICAL DETAILS - 315-630MM
Product
Code
Product
Number
1
31JM/16/4/5/34
2
35JM/16/4/5/22
Ref
Pitch Angle (°)
Full Load
Current
(A)
Starting
Current
(A)
Wiring
Diagram
(CD)
Electronic
BT5
0.075
0.5
1.45
CD3038
ME1.1
TEID 1
1420
BT5
0.075
0.5
1.45
CD3038
ME1.1
TEID 1
Motor
34
1420
22
Max
EJ321460
28
EJ361460
18
Speed Controller
Rating
(kW)
Speed
rev/min
Min
Transformer
3
40JM/16/4/5/40
EJ411452
34
40
1420
BT9
0.25
1.6
3.45
CD3038
ME1.3
TEID 2.2
4
45JM/16/4/5/30
EJ461466
24
30
1420
BT9
0.32
2.2
5
CD3038
ME1.3
TEID 2.2
5
50JM/20/4/6/20
DX511455
16
20
1420
BT9
0.32
2.2
5
CD3038
ME1.3
TEID 2.2
6
50JM/20/4/6/32
EJ511466
32
32
1420
CT9
0.68
4.8
11
CD3038
ME1.6
TEID 5
7
56JM/20/4/6/30
DX571459
26
30
1420
CT9
0.97
6.9
13.5
CD3037
ME1.6
TEID 7.5A
8
63JM/20/4/6/16
DX641453
14
16
1420
CT9
0.97
6.9
13.5
CD3037
ME1.6
TEID 7.5A
For ErP efficiency ratings and grades please refer to our Fan Selector for more information. For speed controllers please see pages 219-267.
roducts in bold are available from our UK Distributors on next day delivery,
P
if ordered by 4pm. Please call to confirm availability on 01206 222 555.
Fläkt Woods
9513 GB 2015.08
Specifications are subject to alteration without notice
19
DRAWINGS - 315-355 MM
315 MM (EJ321460)
2 HOLES SUITABLE
FOR CM20 GLANDS
137
235
30
10 DIA HOLES
IN FOOT
FORM B
K CRS
GUARD OPTIONAL
(IMP. SIDE)
WEIGHT 1.2 kg
200
AIRFLOW
SIGHT PORT
175
FORM A
8 NO OF HOLES 10 DIA.
EQUISPACED ON 355PCD
(EACH END)
MOTOR SIDE
& B/MTH
GUARD
FOOT POSITION
FOR VERT.
MOUNTING
315 DIA. INSIDE
395 DIA. OVER FLANGES
AIRFLOW
C
265 CRS
315
MTG. FOOT
WEIGHT 0.8 kg
Size
Motor
Frame
C
K
Weight kg
Fan
315
BT5
330
245
21
355 MM (EJ361460)
2 HOLES SUITABLE
FOR CM20 GLANDS
8 NO OF HOLES 10 DIA.
EQUISPACED ON 395 PCD
(EACH END)
SIGHT PORT
256
FOOT
POSITION
FOR VERT.
MOUNTING
30
10 DIA HOLES
IN FOOT
225
AIRFLOW
MOTOR SIDE
& B/MTH
GUARD
200
FORM A
C
355 DIA. INSIDE
AIRFLOW
435 DIA. OVER FLANGES
137
FORM B
GUARD OPTIONAL
(IMP. SIDE)
WEIGHT 1.5 kg
K CRS
305 CRS
355
MTG. FOOT
WEIGHT 1.1 kg
Size
Motor
Frame
C
K
Weight kg
Fan
355
BT5
330
245
22
All dimensions in mm.
Fläkt Woods
9513 GB 2015.08
Specifications are subject to alteration without notice
20
DRAWINGS - 400-450 MM
400 MM (EJ411452)
2 HOLES SUITABLE
FOR CM20 GLANDS
137
SIGHT PORT
279
FOOT
POSITION
FOR VERT.
MOUNTING
30
10 DIA HOLES
IN FOOT
FORM B
GUARD OPTIONAL
(IMP. SIDE)
WEIGHT 1.6 kg
250
AIRFLOW
8 NO OF HOLES 12 DIA.
EQUISPACED ON 450 PCD
(EACH END)
225
FORM A
MOTOR SIDE
& B/MTH
GUARD
400 DIA. INSIDE
480 DIA. OVER FLANGES
AIRFLOW
C
350 CRS
K CRS
400
MTG. FOOT
WEIGHT 1.2 kg
Size
Motor
Frame
C
K
Weight kg
Fan
400
BT9
375
290
25
450 MM (EJ461466)
137
2 HOLES SUITABLE
FOR CM20 GLANDS
C
8 NO OF HOLES 12 DIA.
EQUISPACED ON 500 PCD
(EACH END)
SIGHT PORT
450 DIA. INSIDE
MOTOR SIDE
& B/MTH
GUARD
255
30
AIRFLOW
280
530 DIA. OVER FLANGES
FORM A
306
FOOTPOSITION
FOR VERT.
MOUNTING
AIRFLOW
10 DIA HOLES
IN FOOT
FORM B
GUARD OPTIONAL
(IMP. SIDE)
WEIGHT 2.0 kg
K CRS
Size
Motor
Frame
C
K
Weight kg
Fan
450
BT9
330
245
26
400 CRS
450
MTG. FOOT
WEIGHT 1.5 kg
All dimensions in mm.
Fläkt Woods
9513 GB 2015.08
Specifications are subject to alteration without notice
21
DRAWINGS - 500-560 MM
500 MM (DX511455 & EJ511466)
2 HOLES SUITABLE
FOR CM20 GLANDS
137
12 NO OF HOLES 12 DIA.
EQUISPACED ON 560 PCD
(EACH END)
C
SIGHT PORT
30
FORM B
315
MOTOR SIDE
& B/MTH
GUARD
290
AIRFLOW
500 DIA. INSIDE
FORM A
594 DIA. OVER FLANGES
AIRFLOW
338
FOOTPOSITION
FOR VERT.
MOUNTING
10 DIA HOLES
IN FOOT
GUARD OPTIONAL
(IMP. SIDE)
WEIGHT 2.0 kg
450 CRS
K CRS
500
MTG. FOOT
WEIGHT 2.0 kg
Motor
Frame
Size
C
K
Weight kg
Fan
500
BT9
375
289
34
500
CT9
330
245
34
560 MM (DX571459)
2 HOLES SUITABLE
FOR CM20 GLANDS
137
12 NO OF HOLES 12 DIA.
EQUISPACED ON 620 PCD
(EACH END)
C
SIGHT PORT
368
50
355
MOTOR SIDE
& B/MTH
GUARD
330
AIRFLOW
FOOTPOSITION
FOR VERT.
MOUNTING
560 DIA. INSIDE
FORM A
654 DIA. OVER FLANGES
AIRFLOW
10 DIA HOLES
IN FOOT
FORM B
GUARD OPTIONAL
(IMP. SIDE)
WEIGHT 2.5 kg
K CRS
Size
Motor
Frame
C
K
Weight kg
Fan
560
CT9
375
290
38
510 CRS
560
MTG. FOOT
WEIGHT 2.3 kg
All dimensions in mm.
Fläkt Woods
9513 GB 2015.08
Specifications are subject to alteration without notice
22
DRAWING - 630 MM
630 MM (DX641453)
137
ALL GUARDS
OPTIONAL
C
BT, CT, 90, 100 FRAMES
2 HOLES SUITABLE FOR CM20 GLANDS
SIGHT PORT
12 HOLES 12 DIA.
EQUISPACED ON
690 PCD
(EACH END)
FOOT
POSITION
FOR VERT.
MOUNTING
630 DIA. INSIDE
50
400
375
724 DIA. OVER FLANGES
FORM A
D
AIRFLOW
AIRFLOW
FORM B
10 DIA
HOLES
IN FOOT
GUARD OPTIONAL
(IMP. SIDE)
WEIGHT 2.5 kg
K CRS
Size
Motor
Frame
C
D
K
Weight kg
Fan
630
CT9
375
403
290
52
MOTOR
& B/MTH
GUARD 1.4 kg
580 CRS
630
MTG. FOOT
WEIGHT 2.4kg
All dimensions in mm.
Fläkt Woods
9513 GB 2015.08
Specifications are subject to alteration without notice
23
JMv AEROFOIL PERFORMANCE AND ELECTRICAL DATA
ErP
380-420V/50HZ/3f - L TYPE
COMPLIANT
2015
PERFORMANCE CHART - 315MM, 2 POLE
400
1
350
JM
31
v/
6
2/
/
14
300
Static Pressure (Pa)
3
/3
250
200
150
100
50
0
1000
2000
0
3000
4000
0.5
5000
1
6000
m 3/h
7000
1.5
2
m 3/s
Volume Flow
As standard 3 phase JM Aerofoils are supplied at the maximum pitch angle, the envelope curve above illustrates the pitch angle range
available on request.
PERFORMANCE TABLE - 315 MM, 2 POLE
Ref
Product
Code
1
31JMv/14/2/6/33
m3/s @ Pa (Static)
0
50
100
150
200
250
300
1.26
1.22
1.17
1.12
1.06
0.99
0.92
PRODUCT AND ELECTRICAL DETAILS - 315 MM, 2 POLE
Product
Code
Product
Number
31JMv/14/2/6/33
JV346202
Ref
1
Pitch Angle (°)
Min
Max
25
33
Speed
rev/min
Motor
2760
BT9
Speed Controller
Rating
(kW)
Full Load
Current
(A)
Starting
Current
(A)
Wiring
Diagram
(CD)
Electronic
Transformer
Inverter
0.58
1.45
5.7
CD3020
N/A
N/A
IDDXF54 2.2
Sound
Levels
63
For ErP efficiency ratings and grades please refer to our Fan Selector for more information. Sound pressure levels quoted are at the inlet, and are average dBA at
3m distance over a sphere at the mid point at the highest angle given, under free field conditions. These are presented for comparative purposes only. For speed
controllers please see pages 219-267.
Non stocked JM Aerofoil are available in 3 working weeks, based on the parts availability. If a reduced lead time is required please contact the office.
roducts in bold are available from our UK Distributors on next day delivery,
P
if ordered by 4pm. Please call to confirm availability on 01206 222 555.
Fläkt Woods
9513 GB 2015.08
Specifications are subject to alteration without notice
24
JM AEROFOIL PERFORMANCE AND ELECTRICAL DATA
ErP
380-420V/50HZ/3f - L TYPE
COMPLIANT
2015
PERFORMANCE CHART - 315-355 MM, 4 POLE
JM Aerofoil
315 - 355 mm 4 Pole
150
2
100
1
Static Pressure (Pa)
31
JM
/1
6/
4/
5/
35
JM
/
16
/4
/5
/2
6
32
50
0
0
500
0
1000
0.1
0.2
1500
0.3
2000
0.4
0.5
2500
m 3/h
0.7
m 3/s
0.6
Volume Flow
As standard 3 phase JM Aerofoils are supplied at the maximum pitch angle, the envelope curve above illustrates the pitch angle range
available on request.
PERFORMANCE TABLE - 315-355 MM, 4 POLE
Ref
Product
Code
m3/s @ Pa (Static)
0
50
100
1
31JM/16/4/5/32
0.56
0.46
0.29
2
35JM/16/4/5/26
0.71
0.61
0.44
PRODUCT AND ELECTRICAL DETAILS - 315-355 MM, 4 POLE
Ref
Product
Code
Product
Number
Pitch Angle (°)
Min
Max
Speed
rev/min
Motor
Rating
(kW)
Full Load
Current
(A)
Starting
Current
(A)
Wiring
Diagram
(CD)
Speed Controller
Electronic
Transformer
Inverter
Sound
Levels
1
31JM/16/4/5/32
EJ341460
8
32
1420
BT4 (IE1)
0.087
0.35
1.12
CD2416
N/A
TDID 2.5A
IDDXF54-2.2
42
2
35JM/16/4/5/26
EJ381460
8
26
1420
BT4 (IE1)
0.1
0.36
1
CD2416
N/A
TDID 2.5A
IDDXF54-2.2
43
For ErP efficiency ratings and grades please refer to our Fan Selector for more information. Sound pressure levels quoted are at the inlet, and are average dBA at
3m distance over a sphere at the mid point at the highest angle given, under free field conditions. These are presented for comparative purposes only. For speed
controllers please see pages 219-267.
Non stocked JM Aerofoil are available in 3 working weeks, based on the parts availability. If a reduced lead time is required please contact the office.
roducts in bold are available from our UK Distributors on next day delivery,
P
if ordered by 4pm. Please call to confirm availability on 01206 222 555.
Fläkt Woods
9513 GB 2015.08
Specifications are subject to alteration without notice
25
DRAWINGS - 315-355 MM
315 MM (JV346202)
M NO. OF HOLES N DIA.
EQUISPACED ON F PCD
(EACH END)
A
C
FORM B
(Only)
D
L
AIRFLOW
B DIA. OVER FLANGES
A DIA. INSIDE
E
K DIA
HOLES
IN FOOT
G CRS
A
H CRS
J
Product
Code
Motor
frame
A
B
C
D
E
F
G
H
J
K
L
M
N
Weight
(KG)
315
BT4
315
395
375
229.5
3
355
285
265
315
10
200
8
10
23
315 MM (EJ341460)
2 HOLES SUITABLE
FOR CM20 GLANDS
SIGHT PORT
235
FOOT POSITION
FOR VERT.
MOUNTING
30
10 DIA HOLES
IN FOOT
FORM B
K CRS
GUARD OPTIONAL
(IMP. SIDE)
WEIGHT 1.2 kg
200
AIRFLOW
8 NO OF HOLES 10 DIA.
EQUISPACED ON 355PCD
(EACH END)
MOTOR SIDE
& B/MTH
GUARD
175
FORM A
C
315 DIA. INSIDE
AIRFLOW
395 DIA. OVER FLANGES
137
265 CRS
315
MTG. FOOT
WEIGHT 0.8 kg
Size
Motor
Frame
C
K
Weight kg
Fan
315
BT4
330
290
22
Size
Motor
Frame
C
K
Weight kg
Fan
355
BT9
330
245
34
355 MM (EJ381460)
2 HOLES SUITABLE
FOR CM20 GLANDS
8 NO OF HOLES 10 DIA.
EQUISPACED ON 395 PCD
(EACH END)
SIGHT PORT
256
FOOT
POSITION
FOR VERT.
MOUNTING
30
10 DIA HOLES
IN FOOT
225
AIRFLOW
MOTOR SIDE
& B/MTH
GUARD
200
FORM A
C
355 DIA. INSIDE
AIRFLOW
435 DIA. OVER FLANGES
137
FORM B
GUARD OPTIONAL
(IMP. SIDE)
WEIGHT 1.5 kg
K CRS
305 CRS
355
MTG. FOOT
WEIGHT 1.1 kg
All dimensions in mm.
Fläkt Woods
9513 GB 2015.08
Specifications are subject to alteration without notice
26
JM AEROFOIL PERFORMANCE AND ELECTRICAL DATA
ErP
380-420V/50HZ/3f - L TYPE
COMPLIANT
2015
PERFORMANCE CHART - 400-450 MM, 2 POLEJM Aerofoil
400 - 450 mm 2 Pole
1000
900
800
3
600
1
40
JM
/
20
/2
/6
/3
4
6/
2/
5/
32
/1
/1
JM
JM
45
500
45
2
20
5/
2/
6/
Static Pressure (Pa)
700
400
300
200
100
0
0
5000
0
0.5
1
10000
1.5
2
2.5
m 3/h
3
4 m 3/s
3.5
Volume Flow
As standard 3 phase JM Aerofoils are supplied at the maximum pitch angle, the envelope curve above illustrates the pitch angle range
available on request.
PERFORMANCE TABLE - 400-450 MM, 2 POLE
Ref
Product
Code
1
40JM/16/2/5/32
m3/s @ Pa (Static)
0
50
100
150
200
250
300
400
500
2.58
2.51
2.43
2.35
2.26
2.17
2.07
1.85
1.6
3
45JM/16/2/5/20
2.7
2.63
2.56
2.48
2.4
2.32
2.23
2.04
1.81
2
45JM/20/2/6/34
3.87
3.79
3.72
3.63
3.55
3.46
3.37
3.18
2.96
600
700
2.71
2.41
PRODUCT AND ELECTRICAL DETAILS - 400-450 MM, 2 POLE
Ref
Product
Code
Product
Number
Pitch Angle (°)
Min
Max
Speed
rev/min
Motor
Speed Controller
Rating
(kW)
Full Load
Current
(A)
Starting
Current
(A)
Wiring
Diagram
(CD)
Electronic
Transformer
Inverter
Sound
Levels
1
40JM/16/2/5/32
EJ431273
10
32
2840
80 (IE2)
1.73
3.59
18.3
CD2416
N/A
N/A
IDDXF54-3.7
61
2
45JM/16/2/5/20
EE481272
8
20
2840
80 (IE2)
1.73
3.59
18.3
CD2416
N/A
N/A
IDDXF54-3.7
66
3
45JM/20/2/6/34
EJ481275
10
34
2910
100L (IE2)
3.6
7.1
45.44
CD2416
N/A
N/A
IDDXF54-7.2
72
For ErP efficiency ratings and grades please refer to our Fan Selector for more information. Sound pressure levels quoted are at the inlet, and are average dBA at
3m distance over a sphere at the mid point at the highest angle given, under free field conditions. These are presented for comparative purposes only. For speed
controllers please see pages 219-267.
Non stocked JM Aerofoil are available in 3 working weeks, based on the parts availability. If a reduced lead time is required please contact the office.
roducts in bold are available from our UK Distributors on next day delivery,
P
if ordered by 4pm. Please call to confirm availability on 01206 222 555.
Fläkt Woods
9513 GB 2015.08
Specifications are subject to alteration without notice
27
JMv AEROFOIL PERFORMANCE AND ELECTRICAL DATA
ErP
JM Aerofoil
400 - 450 mm 4 Pole
380-420V/50HZ/3f - L TYPE
COMPLIANT
2015
PERFORMANCE CHART - 400-450 MM, 4 POLE
250
200
2
6/
4/
6/
35
v/1
0JM
1 4
Static Pressure (Pa)
1
v/
JM
45
150
100
/18
4/6
6/
50
0
0
1000
2000
0
3000
0.5
4000
1
5000
Volume Flow
6000
7000
1.5
3
9000 m /h
m 3/s
8000
2
2.5
As standard 3 phase JM Aerofoils are supplied at the maximum pitch angle, the envelope curve above illustrates the pitch angle range
available on request.
PERFORMANCE TABLE - 400-450 MM, 4 POLE
m3/s @ Pa (Static)
Ref
Product
Code
0
50
100
1
40JMv/16/4/6/18
0.99
0.90
0.78
2
45JMv/16/4/6/35
2.20
2.00
1.77
150
1.50
PRODUCT AND ELECTRICAL DETAILS - 400-450 MM, 4 POLE
Product
Code
Ref
Product
Number
Pitch Angle (°)
Min
Max
Speed
rev/min
Motor
Rating
(kW)
Full Load
Current
(A)
Starting
Current
(A)
Wiring
Diagram
(CD)
Speed Controller
Electronic
Transformer
Inverter
Sound
Levels
1
40JMv/16/4/6/18
JV436452
14
18
1400
80
0.14
0.40
2.00
CD3020
N/A
N/A
IDDXF54-2.2
51
2
45JMv/16/4/6/35
JV486460
23
35
1400
80
0.66
1.49
7.37
CD3020
N/A
N/A
IDDXF54-2.2
57
For ErP efficiency ratings and grades please refer to our Fan Selector for more information. Sound pressure levels quoted are at the inlet, and are average dBA at
3m distance over a sphere at the mid point at the highest angle given, under free field conditions. These are presented for comparative purposes only. For speed
controllers please see pages 219-267.
Non stocked JM Aerofoil are available in 3 working weeks, based on the parts availability. If a reduced lead time is required please contact the office.
roducts in bold are available from our UK Distributors on next day delivery,
P
if ordered by 4pm. Please call to confirm availability on 01206 222 555.
Fläkt Woods
9513 GB 2015.08
Specifications are subject to alteration without notice
28
DRAWINGS - 400-450 MM 2 POLE
400 MM (EJ431273)
2 HOLES SUITABLE
FOR CM20 GLANDS
137
279
10 DIA HOLES
IN FOOT
FORM B
GUARD OPTIONAL
(IMP. SIDE)
WEIGHT 1.6 kg
250
30
225
AIRFLOW
8 NO OF HOLES 12 DIA.
EQUISPACED ON 450 PCD
(EACH END)
FOOT
POSITION
FOR VERT.
MOUNTING
400 DIA. INSIDE
FORM A
MOTOR SIDE
& B/MTH
GUARD
SIGHT PORT
480 DIA. OVER FLANGES
AIRFLOW
C
350 CRS
K CRS
400
Size
Motor
Frame
C
K
Weight kg
Fan
400
80
375
290
35
MTG. FOOT
WEIGHT 1.2 kg
450 MM (EE481272 & EJ481275)
137
2 HOLES SUITABLE
FOR CM20 GLANDS
C
8 NO OF HOLES 12 DIA.
EQUISPACED ON 500 PCD
(EACH END)
SIGHT PORT
AIRFLOW
450 DIA. INSIDE
MOTOR SIDE
& B/MTH
GUARD
255
30
AIRFLOW
280
530 DIA. OVER FLANGES
FORM A
306
FOOTPOSITION
FOR VERT.
MOUNTING
10 DIA HOLES
IN FOOT
FORM B
GUARD OPTIONAL
(IMP. SIDE)
WEIGHT 2.0 kg
K CRS
400 CRS
450
MTG. FOOT
WEIGHT 1.5 kg
Size
Motor
Frame
C
K
Weight kg
Fan
450
80
375
290
37
450
100L
520
434
60
All dimensions in mm.
Fläkt Woods
9513 GB 2015.08
Specifications are subject to alteration without notice
29
DRAWINGS - 400-450 MM 4 POLE
400 MM (JV436452 & JV486460)
M NO. OF HOLES N DIA.
EQUISPACED ON F PCD
(EACH END)
A
C
FORM B
(Only)
L
AIRFLOW
D
B DIA. OVER FLANGES
A DIA. INSIDE
E
K DIA
HOLES
IN FOOT
G CRS
A
H CRS
J
Product
Code
Motor
frame
A
400
80
450
80
B
C
D
E
400
480
450
530
375
272
375
297
Weight
(KG)
F
G
H
J
K
L
M
N
3
450
285
350
400
10
250
8
10
35
3
500
275
400
450
10
280
8
12
36
All dimensions in mm.
Fläkt Woods
9513 GB 2015.08
Specifications are subject to alteration without notice
30
JM AEROFOIL PERFORMANCE AND ELECTRICAL DATA
ErP
380-420V/50HZ/3f - L TYPE
PERFORMANCE CHART - 500 MM, 2 POLE
COMPLIANT
2015
JM Aerofoil
500 mm 2 Pole
1000
900
1
800
50
JM
Static Pressure (Pa)
700
/2
0/
2/
6/
34
600
500
400
300
200
100
0
0
5000
0
10000
1
2
15000
3
20000
4
m 3/h
m 3/s
5
Volume Flow
As standard 3 phase JM Aerofoils are supplied at the maximum pitch angle, the envelope curve above illustrates the pitch angle range
available on request.
PERFORMANCE TABLE - 500 MM, 2 POLE
Ref
Product
Code
1
50JM/20/2/6/34
m3/s @ Pa (Static)
0
50
100
150
200
250
300
400
500
600
700
800
5.56
5.46
5.36
5.27
5.16
5.06
4.95
4.73
4.49
4.23
3.93
3.58
PRODUCT AND ELECTRICAL DETAILS - 500 MM, 2 POLE
Ref
1
Product
Code
Product
Number
50JM/20/2/6/34
EJ531274
Pitch Angle (°)
Min
Max
10
34
Speed
rev/min
Motor
2910
112M (IE2)
Speed Controller
Rating
(kW)
Full Load
Current
(A)
Starting
Current
(A)
Wiring
Diagram
(CD)
Electronic
Transformer
Inverter
6.2
11.7
77.2
CD2417
N/A
N/A
IDDXF54-12
Sound
Levels
75
For ErP efficiency ratings and grades please refer to our Fan Selector for more information. Sound pressure levels quoted are at the inlet, and are average dBA at
3m distance over a sphere at the mid point at the highest angle given, under free field conditions. These are presented for comparative purposes only. For speed
controllers please see pages 219-267.
Non stocked JM Aerofoil are available in 3 working weeks, based on the parts availability. If a reduced lead time is required please contact the office.
roducts in bold are available from our UK Distributors on next day delivery,
P
if ordered by 4pm. Please call to confirm availability on 01206 222 555.
Fläkt Woods
9513 GB 2015.08
Specifications are subject to alteration without notice
31
JM AEROFOIL PERFORMANCE AND ELECTRICAL DATA
ErP
380-420V/50HZ/3f - L TYPE
PERFORMANCE CHART - 500 MM, 4 POLE
COMPLIANT
2015
JM Aerofoil
500 mm 4 Pole IE2
300
200
Static Pressure (Pa)
1 50JM
/
20/4/
6/40
100
0
0
1000
0
2000
3000
0.5
4000
5000
1
6000
7000
1.5
8000
2
9000
10000
2.5
11000
m 3/h
3
m 3/s
Volume Flow
As standard 3 phase JM Aerofoils are supplied at the maximum pitch angle, the envelope curve above illustrates the pitch angle range
available on request.
PERFORMANCE TABLE - 500 MM, 4 POLE
Ref
Product
Code
1
50JM/20/4/6/40
m3/s @ Pa (Static)
0
50
100
150
2.96
2.76
2.52
2.21
PRODUCT AND ELECTRICAL DETAILS - 500 MM, 4 POLE
Product
Code
Product
Number
50JM/20/4/6/40
EJ531478
Ref
1
Pitch Angle (°)
Min
Max
12
40
Speed
rev/min
Motor
1420
80 (IE2)
Speed Controller
Rating
(kW)
Full Load
Current
(A)
Starting
Current
(A)
Wiring
Diagram
(CD)
Electronic
Transformer
Inverter
0.9
1.92
9.79
CD2416
N/A
N/A
IDDXF54-2.2
Sound
Levels
59
For ErP efficiency ratings and grades please refer to our Fan Selector for more information. Sound pressure levels quoted are at the inlet, and are average dBA at
3m distance over a sphere at the mid point at the highest angle given, under free field conditions. These are presented for comparative purposes only. For speed
controllers please see pages 219-267.
Non stocked JM Aerofoil are available in 3 working weeks, based on the parts availability. If a reduced lead time is required please contact the office.
roducts in bold are available from our UK Distributors on next day delivery,
P
if ordered by 4pm. Please call to confirm availability on 01206 222 555.
Fläkt Woods
9513 GB 2015.08
Specifications are subject to alteration without notice
32
DRAWINGS - 500 MM
500 MM (EJ531274 & EJ531478)
2 HOLES SUITABLE
FOR CM20 GLANDS
137
12 NO OF HOLES 12 DIA.
EQUISPACED ON 560 PCD
(EACH END)
C
SIGHT PORT
30
FORM B
10 DIA HOLES
IN FOOT
GUARD OPTIONAL
(IMP. SIDE)
WEIGHT 2.0 kg
Size
315
AIRFLOW
MOTOR SIDE
& B/MTH
GUARD
290
594 DIA. OVER FLANGES
FORM A
500 DIA. INSIDE
AIRFLOW
338
FOOTPOSITION
FOR VERT.
MOUNTING
Motor
Frame
K CRS
450 CRS
500
MTG. FOOT
WEIGHT 2.0 kg
C
K
Weight kg
Fan
500
80
375
290
39
500
112M
520
434
76
All dimensions in mm.
Fläkt Woods
9513 GB 2015.08
Specifications are subject to alteration without notice
33
JM AEROFOIL PERFORMANCE AND ELECTRICAL DATA
ErP
380-420V/50HZ/3f - L TYPE
PERFORMANCE CHART - 560 MM, 2 POLE
COMPLIANT
2015
JM Aerofoil
560 mm 2 Pole
1200
1100
1000
1
900
56
JM
/2
Static Pressure (Pa)
800
0/
2/
6/
22
700
600
500
400
300
200
100
0
0
5000
0
10000
1
2
15000
3
25000 m 3/h
m 3/s
20000
4
5
6
Volume Flow
As standard 3 phase JM Aerofoils are supplied at the maximum pitch angle, the envelope curve above illustrates the pitch angle range
available on request.
PERFORMANCE TABLE - 560 MM, 2 POLE
Ref
Product
Code
1
56JM/20/2/6/22
m3/s @ Pa (Static)
0
50
100
150
200
250
300
400
500
600
700
800
900
5.95
5.86
5.77
5.68
5.58
5.48
5.38
5.16
4.93
4.68
4.4
4.08
3.72
PRODUCT AND ELECTRICAL DETAILS - 560 MM, 2 POLE
Product
Code
Product
Number
56JM/20/2/6/22
EE591271
Ref
1
Pitch Angle (°)
Min
Max
8
22
Speed
rev/min
Motor
2910
112M (IE2)
Speed Controller
Rating
(kW)
Full Load
Current
(A)
Starting
Current
(A)
Wiring
Diagram
(CD)
Electronic
Transformer
Inverter
6.2
11.7
77.2
CD2417
N/A
N/A
IDDXF54-12
Sound
Levels
72
For ErP efficiency ratings and grades please refer to our Fan Selector for more information. Sound pressure levels quoted are at the inlet, and are average dBA at
3m distance over a sphere at the mid point at the highest angle given, under free field conditions. These are presented for comparative purposes only. For speed
controllers please see pages 219-267.
Non stocked JM Aerofoil are available in 3 working weeks, based on the parts availability. If a reduced lead time is required please contact the office.
roducts in bold are available from our UK Distributors on next day delivery,
P
if ordered by 4pm. Please call to confirm availability on 01206 222 555.
Fläkt Woods
9513 GB 2015.08
Specifications are subject to alteration without notice
34
JM AEROFOIL PERFORMANCE AND ELECTRICAL DATA
ErP
380-420V/50HZ/3f - L TYPE
COMPLIANT
2015
PERFORMANCE CHART - 560 MM, 4 POLE
300
250
/2
JM
56
2
3
6/
4/
0/
v/
JM
56
150
6
/4
20
1
/2
/6
Static Pressure (Pa)
1
200
100
50
0
0
5000
0
0.5
1
10000
1.5
2
15000
2.5
3
3.5
m 3/h
m 3/s
4
Volume Flow
As standard 3 phase JM Aerofoils are supplied at the maximum pitch angle, the envelope curve above illustrates the pitch angle range
available on request.
PERFORMANCE TABLE - 560 MM, 4 POLE
m3/s @ Pa (Static)
Ref
Product
Code
0
50
100
150
200
1
56JM/20/4/6/36
4.08
3.83
3.56
3.26
2.9
2
56JMv/20/4/6/21
3.44
3.24
3.03
2.8
2.52
250
2.15
PRODUCT AND ELECTRICAL DETAILS - 560 MM, 4 POLE
Ref
Product
Code
Product
Number
Pitch Angle (°)
Min
Max
Speed
rev/min
Motor
Rating
(kW)
Full Load
Current
(A)
Starting
Current
(A)
Speed Controller
Wiring
Diagram
(CD)
Electronic
Transformer
Inverter
Sound
Levels
1
56JM/20/4/6/36
EJ591478
10
36
1420
90S (IE2)
1.32
2.84
15.6
CD2416
N/A
N/A
IDDXF54-3.7
62
2
56JMv/20/4/6/21
JV596458
10
21
1400
CT9
1.15
3.2
11
CD3020
N/A
TDID 4A
IDDXF54-3.7
60
For ErP efficiency ratings and grades please refer to our Fan Selector for more information. Sound pressure levels quoted are at the inlet, and are average dBA at
3m distance over a sphere at the mid point at the highest angle given, under free field conditions. These are presented for comparative purposes only. For speed
controllers please see pages 219-267.
Non stocked JM Aerofoil are available in 3 working weeks, based on the parts availability. If a reduced lead time is required please contact the office.
roducts in bold are available from our UK Distributors on next day delivery,
P
if ordered by 4pm. Please call to confirm availability on 01206 222 555.
Fläkt Woods
9513 GB 2015.08
Specifications are subject to alteration without notice
35
DRAWINGS - 560 MM
560 MM (EE591271 & EJ591478)
2 HOLES SUITABLE
FOR CM20 GLANDS
137
12 NO OF HOLES 12 DIA.
EQUISPACED ON 620 PCD
(EACH END)
C
SIGHT PORT
10 DIA HOLES
IN FOOT
FORM B
GUARD OPTIONAL
(IMP. SIDE)
WEIGHT 2.5 kg
510 CRS
K CRS
Motor
Frame
C
K
Weight kg
Fan
560
90S
520
434
55
560
112M
520
434
78
Size
368
50
355
AIRFLOW
MOTOR SIDE
& B/MTH
GUARD
330
FORM A
FOOTPOSITION
FOR VERT.
MOUNTING
560 DIA. INSIDE
654 DIA. OVER FLANGES
AIRFLOW
560
MTG. FOOT
WEIGHT 2.3 kg
560 MM (JV596458)
C
D
L
FORM B
(Only)
B DIA. OVER FLANGES
A DIA. INSIDE
E
AIRFLOW
M NO. OF HOLES N DIA.
EQUISPACED ON F PCD
(EACH END)
A
K DIA
HOLES
IN FOOT
G CRS
A
H CRS
J
Product
Code
Motor
frame
A
B
C
D
E
F
G
H
J
K
L
M
N
Weight
(KG)
560
CT9
560
654
520
352
3
620
420
510
560
10
355
12
12
54
All dimensions in mm.
Fläkt Woods
9513 GB 2015.08
Specifications are subject to alteration without notice
36
JM AEROFOIL PERFORMANCE AND ELECTRICAL DATA
380-420V/50HZ/3f - L TYPE
ErP
JM Aerofoil
630 mm All
PERFORMANCE CHART - 630 MM 4 POLE
COMPLIANT
2015
400
300
63
JM
/2
/
JM
36
6/
4/
0/
63
20
2
/2
/6
/4
Static Pressure (Pa)
2
1
200
100
0
0
5000
0
10000
1
15000
2
3
m 3/h
20000
4
5
6
m 3/s
Volume Flow
As standard 3 phase JM Aerofoils are supplied at the maximum pitch angle, the envelope curve above illustrates the pitch angle range
available on request.
PERFORMANCE TABLE - 630 MM 4 POLE
Ref
Product
Code
m3/s @ Pa (Static)
0
50
100
150
200
250
1
63JM/20/4/6/22
4.04
3.84
3.63
3.39
3.13
2.79
2
63JM/20/4/6/36
5.93
5.61
5.29
4.95
4.59
4.19
PRODUCT AND ELECTRICAL DETAILS - 630 MM 4 POLE
Pitch Angle (°)
Wiring
Diagram
(CD)
Speed Controller
1
63JM/20/4/6/22
EE661473
8
22
1420
90S (IE2)
1.32
2.84
15.6
CD2416
N/A
N/A
IDDXF54-3.7
60
2
63JM/20/4/6/36
EJ661474
12
36
1420
100L (IE2)
2.64
5.49
30.74
CD2416
N/A
N/A
IDDXF54-7.2
64
Max
Motor
Rating
(kW)
Starting
Current
(A)
Product
Number
Min
Speed
rev/min
Full Load
Current
(A)
Product
Code
Ref
Electronic Transformer
Inverter
Sound
Levels
For ErP efficiency ratings and grades please refer to our Fan Selector for more information. Sound pressure levels quoted are at the inlet, and are average dBA at
3m distance over a sphere at the mid point at the highest angle given, under free field conditions. These are presented for comparative purposes only. For speed
controllers please see pages 219-267.
Non stocked JM Aerofoil are available in 3 working weeks, based on the parts availability. If a reduced lead time is required please contact the office.
roducts in bold are available from our UK Distributors on next day delivery,
P
if ordered by 4pm. Please call to confirm availability on 01206 222 555.
Fläkt Woods
9513 GB 2015.08
Specifications are subject to alteration without notice
37
DRAWINGS - 630 MM
630 MM (EE661473 & EJ661474)
ALL GUARDS
OPTIONAL
137
C
BT, CT, 90, 100 FRAMES
2 HOLES SUITABLE FOR CM20 GLANDS
SIGHT PORT
12 HOLES 12 DIA.
EQUISPACED ON
690 PCD
(EACH END)
FOOT
POSITION
FOR VERT.
MOUNTING
630 DIA. INSIDE
50
400
375
724 DIA. OVER FLANGES
FORM A
D
AIRFLOW
AIRFLOW
FORM B
10 DIA
HOLES
IN FOOT
GUARD OPTIONAL
(IMP. SIDE)
WEIGHT 2.5 kg
K CRS
Motor
Frame
C
D
K
630
90S
520
403
434
61
630
100L
520
403
434
80
Size
MOTOR
& B/MTH
GUARD 1.4 kg
580 CRS
630
MTG. FOOT
WEIGHT 2.4kg
Weight kg
Fan
All dimensions in mm.
Fläkt Woods
9513 GB 2015.08
Specifications are subject to alteration without notice
38
JM AEROFOIL PERFORMANCE AND ELECTRICAL DATA
ErP
380-420V/50HZ/3f - L TYPE
COMPLIANT
2015
JM Aerofoil
710 mm
PERFORMANCE CHART - 710 MM, 4 POLE
600
500
2
1
71
JM
300
/2
71
JM
30
6/
4/
0/
Static Pressure (Pa)
400
/2
0/
4/
6/
36
200
100
0
0
5000
0
10000
1
2
15000
3
4
20000
5
25000
6
3
35000 m /h
m 3/s
30000
7
8
9
Volume Flow
As standard 3 phase JM Aerofoils are supplied at the maximum pitch angle, the envelope curve above illustrates the pitch angle range
available on request.
PERFORMANCE TABLE - 710 MM, 4 POLE
m3/s @ Pa (Static)
Ref
Product
Code
0
50
100
150
200
250
300
1
71JM/20/4/6/30
7.64
7.36
7.07
6.77
6.45
6.11
5.73
2
71JM/20/4/6/36
8.74
8.4
8.03
7.65
7.25
6.81
6.33
PRODUCT AND ELECTRICAL DETAILS - 710 MM, 4 POLE
Product
Code
Product
Number
1
71JM/20/4/6/30
2
71JM/20/4/6/36
Ref
Pitch Angle (°)
Speed
rev/min
Min
Max
EE741471
8
30
1440
EJ741474
10
36
1440
Speed Controller
Rating
(kW)
Full Load
Current
(A)
Starting
Current
(A)
Wiring
Diagram
(CD)
Electronic
Transformer
Inverter
100L (IE2)
3.6
7.29
40.09
CD2416
N/A
N/A
IDDXF54-9
67
112M (IE2)
4.8
9.7
49.4
CD2417
N/A
N/A
IDDXF54-9
69
Motor
Sound
Levels
For ErP efficiency ratings and grades please refer to our Fan Selector for more information. Sound pressure levels quoted are at the inlet, and are average dBA at
3m distance over a sphere at the mid point at the highest angle given, under free field conditions. These are presented for comparative purposes only. For speed
controllers please see pages 219-267.
Non stocked JM Aerofoil are available in 3 working weeks, based on the parts availability. If a reduced lead time is required please contact the office.
roducts in bold are available from our UK Distributors on next day delivery,
P
if ordered by 4pm. Please call to confirm availability on 01206 222 555.
Fläkt Woods
9513 GB 2015.08
Specifications are subject to alteration without notice
39
DRAWING - 710 MM
710 MM (EE741471 & EJ741474)
ALL GUARDS
OPTIONAL
137
C
CT, 90, 100, 112 FRAMES
2 HOLES SUITABLE FOR CM20 GLANDS
SIGHT PORT
16 HOLES 12 DIA.
EQUISPACED ON
770 PCD
FOOT
(EACH END)
POSITION
FOR VERT.
MOUNTING
AIRFLOW
B DIA. INSIDE
50
440
415
A DIA. OVER FLANGES
D
FORM A
AIRFLOW
FORM B
J DIA
HOLES
IN FOOT
GUARD OPTIONAL
(IMP. SIDE)
WEIGHT 3.2 kg
Size
Motor
Frame
MOTOR
& B/MTH
GUARD 1.4 kg
K CRS
A
B
C
D
J
K
660 CRS
710
MTG. FOOT
WEIGHT 4.5 kg
Weight kg
Fan
710
100L
804
710
520
443
10
434
84
710
112M
804
710
520
443
10
434
95
All dimensions in mm.
Fläkt Woods
9513 GB 2015.08
Specifications are subject to alteration without notice
40
JM AEROFOIL PERFORMANCE AND ELECTRICAL DATA
ErP
380-420V/50HZ/3f - L TYPE
PERFORMANCE CHART - 800 MM, 4 POLE
COMPLIANT
2015
JM Aerofoil
800 mm 4 Pole
700
600
500
Static Pressure (Pa)
2
80
400
JM
/2
5/
4/
9/
28
300
200
100
0
0
5000
10000
0
15000
2
20000
4
25000
30000
6
35000
8
40000
m 3/h
m 3/s
10
Volume Flow
As standard 3 phase JM Aerofoils are supplied at the maximum pitch angle, the envelope curve above illustrates the pitch angle range
available on request.
PERFORMANCE TABLE - 800 MM, 4 POLE
Ref
1
Product
Code
80JM/25/4/9/28
m3/s @ Pa (Static)
0
50
100
150
200
250
300
400
10.06
9.8
9.53
9.24
8.92
8.58
8.2
7.34
PRODUCT AND ELECTRICAL DETAILS - 800 MM, 4 POLE
Ref
1
Product
Code
Product
Number
80JM/25/4/9/28
EE831478
Pitch Angle (°)
Min
Max
8
28
Speed
rev/min
Motor
1455
132S (IE2)
Speed Controller
Rating
(kW)
Full Load
Current
(A)
Starting
Current
(A)
Wiring
Diagram
(CD)
Electronic
Transformer
Inverter
6.6
12.6
76.25
CD2417
N/A
N/A
IDDXF54-15.5
Sound
Levels
71
For ErP efficiency ratings and grades please refer to our Fan Selector for more information. Sound pressure levels quoted are at the inlet, and are average dBA at
3m distance over a sphere at the mid point at the highest angle given, under free field conditions. These are presented for comparative purposes only. For speed
controllers please see pages 219-267.
Non stocked JM Aerofoil are available in 3 working weeks, based on the parts availability. If a reduced lead time is required please contact the office.
roducts in bold are available from our UK Distributors on next day delivery,
P
if ordered by 4pm. Please call to confirm availability on 01206 222 555.
Fläkt Woods
9513 GB 2015.08
Specifications are subject to alteration without notice
41
DRAWING - 800 MM
800 MM (EE831478)
132-180 FRAMES
2 HOLES SUITABLE FOR CM32 GLANDS
137
ALL GUARDS
OPTIONAL
C
CT, 90, 112 FRAMES
2 HOLES SUITABLE FOR CM20 GLANDS
SIGHT PORT
16 HOLES 12. DIA.
EQUISPACED ON
860 PCD.
FOOT
(EACH END)
POSITION
FOR VERT.
MOUNTING
AIRFLOW
800 DIA. INSIDE
50
510
485
894 DIA. OVER FLANGES
D
FORM A
AIRFLOW
FORM B
GUARD
OPTIONAL
(EITHER END).
WEIGHT 3.5 kg
J DIA
HOLES
IN FOOT.
K CRS
Size
Motor
Frame
C
D
J
K
Weight kg
Fan
800
132S
520
480
12
434
166
MOTOR
AND B/MTH
GUARD 1.5 kg
700 CRS
800
MTG. FOOT
WEIGHT 5.8 kg
All dimensions in mm.
Fläkt Woods
9513 GB 2015.08
Specifications are subject to alteration without notice
42
JM AEROFOIL PERFORMANCE AND ELECTRICAL DATA
ErP
380-420V/50HZ/3f - L TYPE
PERFORMANCE CHART - 900 MM, 4 POLE
COMPLIANT
2015
JM Aerofoil
900 mm 4 Pole
800
700
600
1
2
/2
4
/2
/9
/4
34
9/
4/
5/
25
Static Pressure (Pa)
JM
/
JM
90
90
500
400
300
200
100
0
0
0
10000
20000
2
4
30000
6
40000
8
10
50000
12
m 3/h
60000
14
16
18
m 3/s
Volume Flow
As standard 3 phase JM Aerofoils are supplied at the maximum pitch angle, the envelope curve above illustrates the pitch angle range
available on request.
PERFORMANCE TABLE - 900 MM, 4 POLE
Ref
Product
Code
m3/s @ Pa (Static)
0
50
100
150
200
250
300
400
500
600
8.79
1
90JM/25/4/9/24
13.21
12.9
12.6
12.29
11.97
11.65
11.33
10.64
9.85
2
90JM/25/4/9/34
17.07
16.67
16.26
15.84
15.4
14.94
14.46
13.44
12.29
PRODUCT AND ELECTRICAL DETAILS - 900 MM, 4 POLE
Pitch Angle (°)
Product
Code
Product
Number
1
90JM/25/4/9/24
EE931473
8
24
1440
132M (IE2)
2
90JM/25/4/9/34
EJ931476
10
34
1440
160M (IE2)
Ref
Min
Max
Speed
rev/min
Motor
Speed Controller
Full Load
Current
(A)
Starting
Current
(A)
Wiring
Diagram
(CD)
Electronic
Transformer
Inverter
9
17.1
100.89
CD2417
N/A
N/A
IDDXF54-23
75
13.2
25.3
135.7
CD2417
N/A
N/A
IDDXF54-31
77
Rating
(kW)
Sound
Levels
For ErP efficiency ratings and grades please refer to our Fan Selector for more information. Sound pressure levels quoted are at the inlet, and are average dBA at
3m distance over a sphere at the mid point at the highest angle given, under free field conditions. These are presented for comparative purposes only. For speed
controllers please see pages 219-267.
Non stocked JM Aerofoil are available in 3 working weeks, based on the parts availability. If a reduced lead time is required please contact the office.
roducts in bold are available from our UK Distributors on next day delivery,
P
if ordered by 4pm. Please call to confirm availability on 01206 222 555.
Fläkt Woods
9513 GB 2015.08
Specifications are subject to alteration without notice
43
DRAWING - 900 MM
900 MM (EE931473 & EJ931476)
112 FRAMES
2 HOLES SUITABLE FOR CM20 GLANDS
137
ALL GUARDS
OPTIONAL
C
132, 160 FRAMES
2 HOLES SUITABLE FOR CM32 GLANDS
SIGHT PORT
16 HOLES 15 DIA.
EQUISPACED ON
970 PCD (EACH END) FOOT
POSITION
FOR VERT.
MOUNTING
900 DIA. INSIDE
50
518
491
1006 DIA. OVER FLANGES
FORM A
D
AIRFLOW
AIRFLOW
FORM B
J DIA
HOLES
IN FOOT
GUARD OPTIONAL
(IMP. SIDE)
WEIGHT 4.2 kg
Size
Motor
Frame
C
MOTOR
& B/MTH
GUARD 1.7 kg
K CRS
D
J
K
850 CRS
900
MTG. FOOT
WEIGHT 5.3 kg
Weight kg
Fan
900
132M
520
575
12
440
179
900
160M
625
575
12
545
248
All dimensions in mm.
Fläkt Woods
9513 GB 2015.08
Specifications are subject to alteration without notice
44
JM AEROFOIL PERFORMANCE AND ELECTRICAL DATA
ErP
380-420V/50HZ/3f - L TYPE
PERFORMANCE CHART - 1000 MM, 4 POLE
COMPLIANT
2015
JM Aerofoil
1000 mm 4 Pole
1000
900
800
Static Pressure (Pa)
700
2
600
500
1
10
400
300
0J
M
/2
10
0J
M
/2
5/
4/
9/
28
5/
4/
6/
22
200
100
0
0
10000
20000
0
30000
5
40000
50000
60000
10
70000
15
m 3/h
80000
m 3/s
20
Volume Flow
As standard 3 phase JM Aerofoils are supplied at the maximum pitch angle, the envelope curve above illustrates the pitch angle range
available on request.
PERFORMANCE TABLE - 1000 MM, 4 POLE
Ref
Product
Code
m3/s @ Pa (Static)
0
50
100
150
200
250
300
400
500
1
100JM/25/4/6/22
16.46
15.91
15.35
14.78
14.21
13.62
13.01
11.68
10.04
2
100JM/25/4/9/28
20.96
20.52
20.07
19.61
19.12
18.63
18.11
16.99
15.75
600
14.33
PRODUCT AND ELECTRICAL DETAILS - 1000 MM, 4 POLE
Pitch Angle (°)
Product
Code
Product
Number
1
100JM/25/4/6/22
EE133472
8
2
100JM/25/4/9/28
EE131475
8
Ref
Min
Speed
rev/min
Motor
22
1440
132M (IE2)
28
1470
160L (IE2)
Max
Full Load
Current
(A)
Starting
Current
(A)
9
17.1
100.89
CD2417
18
34.2
177.81
CD2417
Rating
(kW)
Wiring
Diagram
(CD)
Speed Controller
Electronic
Sound
Levels
Transformer
Inverter
N/A
N/A
IDDXF54-23
79
N/A
N/A
IDDXF54-37
81
Sound pressure levels quoted are at the inlet, and are average dBA at 3m distance over a sphere at the mid point at the highest angle given, under free field For ErP
efficiency ratings and grades please refer to our Fan Selector for more information. These are presented for comparative purposes only. For speed controllers please
see pages 219-267.
Non stocked JM Aerofoil are available in 3 working weeks, based on the parts availability. If a reduced lead time is required please contact the office.
roducts in bold are available from our UK Distributors on next day delivery,
P
if ordered by 4pm. Please call to confirm availability on 01206 222 555.
Fläkt Woods
9513 GB 2015.08
Specifications are subject to alteration without notice
45
DRAWING 1000 MM
1000 MM (EE133472 & EE131475)
112 FRAMES
2 HOLES SUITABLE FOR CM20 GLANDS
137
C
132, 160 FRAMES
2 HOLES SUITABLE FOR CM32 GLANDS
ALL GUARDS
OPTIONAL
16 HOLES 15 DIA.
EQUISPACED ON
1070 PCD
(EACH END)
FOOT
POSITION
FOR VERT.
MOUNTING
SIGHT PORT
AIRFLOW
1000 DIA. INSIDE
574
50
AIRFLOW
547
1106 DIA. OVER FLANGES
D
FORM A
FORM B
J DIA
HOLES
IN FOOT
GUARD OPTIONAL
(IMP. SIDE)
MOTOR
& B/MTH
GUARD 2 kg
K CRS
WEIGHT 5 kg
Size
Motor
Frame
C
1000
132M
1000
160L
K
950 CRS
1000
MTG. FOOT
WEIGHT 6.2 kg
Weight kg
Fan
D
J
520
625
12
440
218
711
625
12
629
295
All dimensions in mm.
Fläkt Woods
9513 GB 2015.08
Specifications are subject to alteration without notice
46
WIRING DIAGRAMS - JM AEROFOIL
CD3038 - 315-500 JM 1 PHASE (WITHOUT AND WITH ME SPEED CONTROLLER)
FAN
TERMINAL
BLOCK
PE
K
K
UZ
U
Z
ALL
M.E SPEED
CONTROLLER
PE
L
N
UZ
U
Z
PE
L
N
P
U
BLACK
BLACK
BLACK
UZ
SINGLE PHASE FAN
WITH INTERNAL CAPACITOR
AND OVERHEAT PROTECTION
BLACK
BLACK
OVERHEAT
PROTECTION
A
FAN
TERMINAL
BLOCK
PE
K
K
PE
L
N
CAPACITOR
FITTED TO
MOTOR
P
P BLACK
UZ BLACK
BLACK
BLACK
OVERHEAT PROTECTION
U BLACK
A
B
UZ
Z
U
P
CAPACITOR
FITTED TO
MOTOR
230V/50Hz SINGLE
PHASE PROTECTED
SUPPLY
3-WIRE CONTROL
UZ (LIVE)
U (VARIABLE NEUTRAL)
Z (FULL NEUTRAL)
230V/50Hz SINGLE
PHASE PROTECTED
SUPPLY
FAN CONNECTED TO SUPPLY (FULL SPEED)
FAN CONNECTED TO SPEED CONTROLLER (VARIABLE SPEED)
CD3037 - 560-630 JM 1 PHASE (WITHOUT AND WITH ME SPEED CONTROLLER)
K
K
UZ
U
Z
ALL
M.E SPEED
CONTROLLER
PE
L
N
UZ
U
Z
P
BLACK
BLACK
U
PE
SINGLE PHASE FAN
WITH INTERNAL CAPACITOR
AND OVERHEAT PROTECTION
BLACK
FAN
TERMINAL
BLOCK
BLACK
UZ BLACK
OVERHEAT PROTECTION
BLACK
A
FAN
TERMINAL
BLOCK
PE
PE
K
L
K
N
230V/50Hz SINGLE
PHASE PROTECTED
SUPPLY
P BLACK
BLACK
BLACK
OVERHEAT PROTECTION
U
UZ BLACK
A
9513 GB 2015.08
CAPACITOR
FITTED TO
MOTOR
B
UZ
U
Z
P
CAPACITOR
FITTED TO
MOTOR
FOR OVER HEAT PROTECTION CONNECT THE
THERMAL CUT OUT TERMINALS 'K'
TO A RE-SETTABLE DEVICE WHEN
FLA EXCEEDS 6.3A (IF APPLICABLE REMOVE
LINK AAND CONNECT LIVE WIRE 'UZ'FROM
THE SPEED CONTROLLER TO TERMINAL 'UZ'
ON THE FAN TERMINAL BLOCK).
FAN CONNECTED TO SUPPLY (FULL SPEED)
Fläkt Woods
P
PE
L
N
230V/50Hz SINGLE
PHASE PROTECTED
SUPPLY
3-WIRE CONTROL
UZ (LIVE)
U (VARIABLE NEUTRAL)
Z (FULL NEUTRAL)
FOR OVER HEAT PROTECTION
CONNECT THE THERMAL
CUT OUT TERMINALS 'K'
TO A RE-SETTABLE DEVICE
WHEN FLA EXCEEDS 6.3A
(IF APPLICABLE REMOVE
LINK AAND CONNECT LIVE
WIRE 'UZ'FROM THE SPEED
CONTROLLER TO TERMINAL
'UZ' ON THE FAN TERMINAL BLOCK).
FAN CONNECTED TO SPEED CONTROLLER (VARIABLE SPEED)
Specifications are subject to alteration without notice
47
WIRING DIAGRAMS - JM AEROFOIL
CD3033 - JM 1 PHASE (CONNECTED TEID 1A)
JM CONNECTED TO TEID 1.5-2.2A TRANSFORMER SPEED CONTROLLER
JM CONNECTED TO TEID 1A TRANSFORMER SPEED CONTROLLER
FAN
TERMINAL
BLOCK
E
K
K
UZ
U
UZ
U
P
Z
P
TEID 1A SPEED CONTROLLER
L
N
PE
N1
L1
CD3035 - JM 1 PHASE (CONNECTED TEID 1.5-2.2A)
N
U
PE
FAN
TERMINAL
BLOCK
E
TEID 1.5-2.2A
SPEED
CONTROLLER
PE
K
L
L = 240 VOLT FUSED SUPPLY
N = NEUTRAL
L1/N1 = AN UNREGULATED OUTPUT,
USED FOR 240 VOLT OUTPUT
IN
230 VAC
CD3034 - JM 1 PHASE (CONNECTED TEID 3.5-5.5A)
K
N
UZ
U
UZ
U
P
Z
P
L1
N1
U
N
L = 240 VOLT FUSED SUPPLY
N = NEUTRAL
L1/N1 = AN UNREGULATED OUTPUT,
USED FOR 240 VOLT OUTPUT
IN
230 VAC
CD3034 - JM 1 PHASE (CONNECTED TEID 7.5-13A)
K
K
UZ
U
P
U
FUSE
TEID 3.5 - 5.5A SPEED CONTROLLER
L
N
N
L1
Z
IN
230 VAC
ATED OUTPUT,
0 VOLT OUTPUT
Fläkt Woods
E
K
K
UZ
U
TEID 7.5 - 13A SPEED CONTROLLER
L
N
N
L1
Z
P
FAN
TERMINAL
BLOCK
9513 GB 2015.08
L = 240 VOLT FUSED SUPPLY
N = NEUTRAL
L1= AN UNREGULATED OUTPUT,
USED FOR 240 VOLT OUTPUT
PE
IN
230 VAC
E
TEID 3.5 - 5.5A
L
U
PE
PE
SED SUPPLY
FAN
TERMINAL
BLOCK
CONNECTION OF EXTERNAL
SAFETY CIRCUIT TO 'K' 'K
CONNECT THERMAL CUT
OUT TERMINALS 'K' TO AN
EXTERNAL RE-SETTABLE
DEVICE.
CONNECT LIVE MOTOR
WIRE U ON SPEED
CONTROL TO 'UZ'
ON THE MOTOR
TERMINAL BLOCK.
FUSE
E
CONNECTION OF EXTERNAL
SAFETY CIRCUIT TO 'K' 'K
CONNECT THERMAL CUT
OUT TERMINALS 'K' TO AN
EXTERNAL RE-SETTABLE
DEVICE.
CONNECT LIVE MOTOR
WIRE U ON SPEED
CONTROL TO 'UZ'
ON THE MOTOR
TERMINAL BLOCK.
FUSE
A
FAN
TERMINAL
BLOCK
P
UZ
P
U
UZ
CONNECTION OF EXTERNAL
SAFETY CIRCUIT TO 'K' 'K
CONNECT THERMAL CUT
OUT TERMINALS 'K' TO AN
EXTERNAL RE-SETTABLE
DEVICE.
CONNECT LIVE MOTOR
WIRE U ON SPEED
CONTROL TO 'UZ'
ON THE MOTOR
TERMINAL BLOCK.
U
JM & MAXFAN CONNECTED TO TEID TRANSFORMER SPEED CONTROLLER
NTROLLER
L = 240 VOLT FUSED SUPPLY
N = NEUTRAL
L1= AN UNREGULATED OUTPUT,
USED FOR 240 VOLT OUTPUT
Specifications are subject to alteration without notice
48
WIRING DIAGRAMS - JMv AEROFOIL
CD3020
CONNECTION DIAGRAM FOR THREE PHASE DELTA FIXED SPEED
ACDE ROTATION
V
U
W
(L2)
(L1)
(L3)
U1
V1
W1
DELTA
U2
W2
RED
BLUE
V2
WHITE
GREY
ADDITIONAL
CIRCUITS WHEN FITTED:
THERMAL PROTECTION
SS- THERMISTOR
KK - THERMOSTAT
BLACK
PE
BROWN
TERMINATES
TO BOX
CASING
INCOMING MOTOR LEADS TO MATCH TERMINAL BLOCK LETTERING
CD3018
(L2)
(L1)
(L3)
U1
V1
W1
V2
U2
W2
BROWN
BLACK
GREY
WHITE
RED
BLUE
CONNECTION DIAGRAM FOR THREE PHASE DUAL VOLTAGE, STAR
ACDE ROTATION
V
U
W
STAR
TERMINATES
TO BOX
CASING
PE
ADDITIONAL
CIRCUITS WHEN FITTED:
THERMAL PROTECTION
SS- THERMISTOR
KK - THERMOSTAT
INCOMING MOTOR LEADS TO MATCH TERMINAL BLOCK LETTERING
Fläkt Woods
9513 GB 2015.08
Specifications are subject to alteration without notice
49
WIRING DIAGRAMS
- JM AEROFOIL
CD2416
CD2416
THREE PHASE JM
STAR CONNECTION
U1
V1
W1
INCOMING MOTOR LEADS
TO MATCH TERMINAL
BLOCK LETTERING.
K
K
U1
V1
W1
K
K
U
V
W
L1
L2
L3
ADDITIONAL
CIRCUITS WHEN FITTED:
THERMAL PROTECTION
SS - THERMISTOR
KK - THERMOSTAT
V2
U2
W2
PE
EARTH TO
TERMINAL
BODY CASE
THREE PHASE SUPPLY
TO REVERSE ROTATION SWAP
ANY 2 INCOMING PHASES
CD2417
CD2417
THREE PHASE JM
DELTA CONNECTION
INCOMING MOTOR LEADS
TO MATCH TERMINAL
BLOCK LETTERING.
K
K
U1
V1
W1
K
K
U
V
W
V2
L1
L2
L3
THREE PHASE SUPPLY
TO REVERSE ROTATION SWAP
ANY 2 INCOMING PHASES
9513 GB 2015.08
W2
FOR USE ON STAR/DELTA
PACK REMOVE LINKS
ADDITIONAL
CIRCUITS WHEN FITTED:
THERMAL PROTECTION
SS - THERMISTOR
KK - THERMOSTAT
Fläkt Woods
U2
PE
EARTH TO
TERMINAL
BODY CASE
Specifications are subject to alteration without notice
ALSO AVAILABLE FROM
THE WOODS RANGE
JMv
Aerofoil
MaXfan2
JM
Aerofoil
HT JM
Aerofoil
JM
Bifurcated
Series 33
Plate Fans
Cased &
Plate Axial
Tube Fans
Sabina EC
Box Fans
Daisho AC
Box Fans
Estoc EC
Estoc
Estoc Targe
Roof Units
Horizontal
Roof Units
Vertical
Fire
Dampers
Fire Valves
Valves
Supply KE
Valves
Extract KK
Nozzles DK
& DR
Louvres/
Cowls
EYMA and
DYMA
External
Louvres
USAV
Accessories
Daisho EC
Box Fans
Tube & Box
Accessories
Iris
Dampers
Valves
Exhaust
VEFS
Controllers
Selected products available from our UK Distributors on next day delivery,
if ordered by 4pm. Please call 01206 222 555 for more information.
Fläkt Woods
9513 GB 2015.08
Specifications are subject to alteration without notice