SERVICE MANUAL

Transcription

SERVICE MANUAL

CDX-GT410U/GT414U
SERVICE MANUAL
AEP Model
UK Model
Ver. 1.1 2007.03
(Photo: CDX-GT410U)
• The tuner and CD sections have no adjustments.
Model Name Using Similar Mechanism
NEW
CD Drive Mechanism Type
MG-101U-188//Q
Optical Pick-up Name
DAX-25A
SPECIFICATIONS
CD player section
Signal-to-noise ratio
Frequency response
Wow and flutter
MW/LW
Tuning range
MW: 531 – 1,602 kHz
LW: 153 – 279 kHz
Antenna terminal
External antenna connector
Intermediate frequency 10.7 MHz/450 kHz
Sensitivity
MW: 30 µV, LW: 40 µV
120 dB
10 – 20,000 Hz
Below measurable limit
Tuner section
FM
Tuning range
87.5 – 108 MHz
Antenna terminal
External antenna connector
Intermediate frequency 10.7 MHz/450 kHz
Usable sensitivity
9 dBf
Selectivity
75 dB at 400 kHz
Signal-to-noise ratio
67 dB (stereo), 69 dB (mono)
Harmonic distortion at 1 kHz
0.5% (stereo), 0.3% (mono)
Separation
35 dB at 1 kHz
Frequency response
30 – 15,000 Hz
USB player section
Interface
USB (Full-speed)
Maximum current
500 mA
Power amplifier section
Outputs
Speaker outputs (sure seal connectors)
Speaker impedance
4 – 8 ohms
Maximum power output
50 W × 4 (at 4 ohms)
– Continued on next page –
FM/MW/LW COMPACT DISC PLAYER
9-887-452-02
2007C04-1
© 2007.03
Sony Corporation
eVehicle Division
Published by Sony Techno Create Corporation
CDX-GT410U/GT414U
General
Outputs
Inputs
Tone controls
Power requirements
Dimensions
Mounting dimensions
Mass
Supplied accessories
Audio outputs terminal (sub/rear switchable)
Power antenna relay control terminal
Power amplifier control terminal
Telephone ATT control terminal
BUS control input terminal
BUS audio input terminal
Antenna input terminal
AUX input jack (stereo mini jack)
Low: ±10 dB at 60 Hz (XPLOD)
Mid: ±10 dB at 1 kHz (XPLOD)
High: ±10 dB at 10 kHz (XPLOD)
12 V DC car battery (negative ground)
Approx. 178 × 50 × 179 mm
(7 1/8 × 2 × 7 1/8 in.) (w/h/d)
Approx. 182 × 53 × 162 mm
(7 1/4 × 2 1/8 × 6 1/2 in.) (w/h/d)
Approx. 1.2 kg (2 lb. 11 oz.)
Card remote commander: RM-X151
Parts for installation and connections (1 set)
USB cap
Design and specifications are subject to change without
notice.
Notes on Chip Component Replacement
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be damaged
by heat.
TEST DISCS
Please use the following test discs for the check on the CD section.
YDES-18 (Part No. 3-702-101-01)
PATD-012 (Part No. 4-225-203-01)
CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
radiation exposure.
If the optical pick-up block is defective, please replace the whole
optical pick-up block.
Never turn the semi-fixed resistor located at the side of optical pickup block.
US and foreign patents licensed from Dolby Laboratories.
optical pick-up
SERVICE NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pickup block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
2
semi-fixed resistor
CDX-GT410U/GT414U
This compact disc player is classified as a CLASS 1 LASER
product. The CLASS 1 LASER PRODUCT label is located on the
exterior.
SOLDER
• UNLEADED
Boards requiring use of unleaded solder are printed with the leadfree mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
This label is located on the bottom of the chassis.
• CD playback
You can play CD-DA (also containing CD TEXT*), CD-R/CDRW (MP3/WMA/AAC files also containing Multi Session) and
ATRAC CD (ATRAC3 and ATRAC3plus format).
Type of discs
Label on the disc
CD-DA
MP3
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
WMA
AAC
ATRAC CD
* A CD TEXT disc is a CD-DA that includes information such as
disc, artist and track name.
EXTENSION CABLE AND SERVICE POSITION
When repairing or servicing this set, connect the jig (extension cable)
as shown below.
• Connect the MAIN board (CN350) and the SERVO board (CN2)
with the extension cable (Part No. J-2502-076-1).
MAIN BOARD
CN350
J-2502-076-1
SERVO BOARD
CN2
3
CDX-GT410U/GT414U
Ver. 1.1
NOTE FOR REPLACEMENT OF THE SERVO BOARD
When repairing, the complete SERVO board (A-1177-201-A) should
be replaced since any parts in the SERVO board cannot be repaired.
TABLE OF CONTENTS
1.
GENERAL
Location of Controls ........................................................ 5
Connections ..................................................................... 6
NOTE FOR REPLACEMENT OF THE USB CONNECTOR
(CN902)
To replace the USB connector requires alignment.
1. Insert the USB connector into the front panel.
2. Place the KEY board on the front panel and align the terminals
of the USB connector with the holes in the KEY board.
3. Solder the four terminals of the connector.
2.
DISASSEMBLY
2-1.
2-2.
2-3.
2-4.
2-5.
2-6.
2-7.
Sub Panel (FL) Assy ........................................................
CD Mechanism Block .....................................................
Main Board ......................................................................
Servo Board .....................................................................
Chassis (T) Sub Assy .......................................................
Roller Arm Assy ..............................................................
Chassis (OP) Assy ...........................................................
3.
DIAGNOSIS FUNCTION ........................................ 13
4.
DIAGRAMS
4-1.
4-2.
4-3.
4-4.
4-5.
4-6.
4-7.
4-8.
Block Diagram –Main Section– ......................................
Block Diagram –Display Section– ..................................
Printed Wiring Board –Main Section– ............................
Schematic Diagram –Main Section (1/3)– ......................
Printed Wiring Board –Key Section– ..............................
Schematic Diagram –Key Section– .................................
5.
EXPLODED VIEWS
9
9
10
10
11
11
12
KEY board
USB (socket) connector
17
18
20
21
22
23
24
25
5-1. Main Section .................................................................... 31
5-2. Front Panel Section ......................................................... 32
5-3. CD Mechanism Section (MG-101U-188//Q) .................. 33
6.
front panel
NOTE FOR THE 24-PIN CONNECTOR (CN901)
Do not use alcohol to clean the 24-pin connector (CN901) connecting
the front panel with the main body.
Do not touch the connector directly with your bare hand. Poor contact
may be caused.
4
ELECTRICAL PARTS LIST .................................. 34
CDX-GT410U/GT414U
SECTION 1
GENERAL
This section is extracted
from instruction manual.
• LOCATION OF CONTROLS
Location of controls and basic operations
Main unit
12 3
4
5
6
7 8
OFF
PUSH SELECT
EQ3
SOURCE
SEEK
SEEK
L Receptor for the card remote
commander
MODE
PTY
GP/ALBM
DIM
1
DSPL
2
REP
SHUF
3
4
PAUSE
5
6
AUX
AF/TA
CDX-GT414U
9 q; qa qs qdqfqg
Card remote commander
RM-X151
1
4
ql
OFF
SOURCE
ATT
SEL
MODE
wa
ws
qd
+
wd
w;
SCRL
DSPL
1
2
3
4
5
6
+
VOL
–
qj qk CDX-GT410U
Refer to the pages listed for details. The
corresponding buttons on the card remote
commander control the same functions as those
on the unit.
A OFF button
To power off; stop the source.
B EQ3 (equalizer) button 11
To select an equalizer type (XPLOD,
VOCAL, EDGE, CRUISE, SPACE,
GRAVITY, CUSTOM or OFF).
wf
C Volume control dial/select button 11
To adjust volume (rotate); select setup items
(press and rotate).
wg
D SOURCE button
To power on; change the source (Radio/CD/
MD*1/USB/AUX).
–
qf
qh
M MODE button 8, 13
To select the radio band (FM/MW/LW);
select the unit*3; select the play mode*4.
N DSPL (display)/DIM (dimmer) button
8, 9
To change display items (press); change the
display brightness (press and hold).
wa ATT (attenuate) button
To attenuate the sound. To cancel, press
again.
ws SEL (select) button
The same as the select button on the unit.
wd M (+)/m (–) buttons
To control CD, the same as (1)/(2) (GP/
ALBM –/+) on the unit.
wg Number buttons
To receive stored stations (press); store
stations (press and hold).
R AUX input jack 12
To connect a portable audio device.
J
w; VOL (volume) +/– button
To adjust volume.
P Number buttons
CD/MD*1/USB*2:
(1)/(2): GP*5/ALBM*6 –/+
To skip albums (press); skip albums
continuously (press and hold)*7.
(3): REP 8
(4): SHUF 8
(6): PAUSE*8
To pause playback. To cancel, press
again.
Radio:
To receive stored stations (press); store
stations (press and hold).
F Display window
I PTY (Program Type) button 10
To select PTY in RDS.
ql < (.)/, (>) buttons
To control CD/radio/MD/USB, the same as
(SEEK) –/+ on the unit.
wf SCRL (scroll) button 8
To scroll the display item.
Q AF (Alternative Frequencies)/TA
(Traffic Announcement) button 9
To set AF and TA in RDS.
H Z (eject) button
To eject the disc.
The following buttons on the card remote
commander have also different buttons/functions
from the unit. Remove the insulation film before
use (page 4).
O RESET button (located behind the front
panel) 4
E Disc slot
Insert the disc (label side up), playback
starts.
G USB terminal
To connect to the USB device. 10
6
K SEEK –/+ buttons
CD/MD*1/USB*2:
To skip tracks (press); skip tracks
continuously (press, then press again within
about 1 second and hold); reverse/fastforward a track (press and hold).
Radio:
To tune in stations automatically (press); find
a station manually (press and hold).
When an MD changer is connected.
When a USB device is connected.
When a CD/MD changer is connected.
When an ATRAC Audio Device is connected.
When an ATRAC CD is played.
When an MP3/WMA/AAC is played.
If the changer/USB device is connected, the
operation is different, see page 10, 13.
*8 When playing back on this unit.
*1
*2
*3
*4
*5
*6
*7
Notes
• When ejecting/inserting a disc, keep any USB
devices disconnected to avoid damage to the disc.
• If the unit is turned off and the display disappears, it
cannot be operated with the card remote
commander unless (SOURCE) on the unit is
pressed, or a disc is inserted to activate the unit first.
Tip
For details on how to replace the battery, see
“Replacing the lithium battery of the card remote
commander” on page 16.
About USB cap
When not using the USB terminal (G), use the
supplied USB cap to prevent dust or dirt entering.
Keep the USB cap out of the reach of children to
prevent accidental swallowing.
(front panel release) button 5
7
5
CDX-GT410U/GT414U
• CONNECTIONS
Connection example
Notes (2-A)
• Be sure to connect the ground (earth) lead before connecting
the amplifier.
• The alarm will only sound if the built-in amplifier is used.
A
Tip (2-B- )
For connecting two or more CD/MD changers, the source
selector XA-C40 (not supplied) is necessary.
Anschlussbeispiel
AUDIO OUT REAR*
Hinweise (2-A)
• Schließen Sie unbedingt zuerst das Massekabel an, bevor Sie
den Verstärker anschließen.
• Der Warnton wird nur ausgegeben, wenn der integrierte
Verstärker verwendet wird.
Tipp (2-B- )
Zum Anschließen von zwei oder mehr CD/MD-Wechslern wird
der Signalquellenwähler XA-C40 (nicht mitgeliefert) benötigt.
* AUDIO OUT SUB/REAR
B
Exemple de raccordement
BUS AUDIO IN
Remarques (2-A)
• Raccordez d’abord le câble de mise à la masse avant de
raccorder l’amplificateur.
• L’alarme est émise uniquement lorsque l’amplificateur intégré
est utilisé.
Conseil (2-B- )
Dans le cas du raccordement de deux changeurs de CD/MD
ou plus, le sélecteur de source XA-C40 (non fourni) est
indispensable.
BUS CONTROL IN
Esempio di collegamento
Note (2-A)
• Assicurarsi di collegare il cavo di terra prima di collegare
l’apparecchio all’amplificatore.
• L’allarme viene emesso solo se è in uso l’amplificatore
incorporato.
BUS AUDIO IN
Suggerimento (2-B- )
Per collegare due o più cambia CD/MD, occorre utilizzare il
selettore di fonte XA-C40 (non in dotazione).
Source selector*
Signalquellenwähler*
Sélecteur de source*
Selettore di fonte*
Bronkeuzeschakelaar*
XA-C40
Voorbeeldaansluitingen
BUS CONTROL IN
* not supplied
nicht mitgeliefert
non fourni
non in dotazione
niet bijgeleverd
Opmerkingen (2-A)
• Sluit eerst de aardingskabel aan voordat u de versterker
aansluit.
• U hoort de pieptoon alleen als de ingebouwde versterker wordt
gebruikt.
Tip (2-B- )
Om twee of meer CD/MD-wisselaars aan te sluiten, hebt u de
bronkeuzeschakelaar XA-C40 (niet bijgeleverd) nodig.
6
CDX-GT410U/GT414U
Supplied with XA-C40
Mit dem XA-C40 geliefert
Fourni avec le XA-C40
In dotazione con il modello XA-C40
Geleverd met de XA-C40
*1 Note for the antenna (aerial) connecting
If your car antenna (aerial) is an
ISO (International Organization for
Standardization) type, use the supplied
adaptor 2 to connect it. First connect
the car antenna (aerial) to the supplied
adaptor, then connect it to the antenna
(aerial) jack of the master unit.
2
* RCA pin cord (not supplied)
*3 AUDIO OUT can be switched SUB or
REAR. For details, see the supplied
Operating Instructions.
Supplied with the CD/MD changer
Mit dem CD/MD-Wechsler geliefert
Fourni avec le changeur de CD/MD
In dotazione con il cambia CD/MD
Geleverd met de CD/MD-wisselaar
2
L
von Autoantenne
de l’antenne de la voiture
dall’antenna dell’auto
van een auto-antenne
R
BUS AUDIO OUT
IN
REAR/SUB
Fuse (10 A)
Sicherung (10 A)
Fusible (10 A)
Fusibile (10 A)
Zekering (10 A)
BUS AUDIO IN
AUDIO OUT REAR*3
Max. supply current 0.3 A
max. Versorgungsstrom 0,3 A
Courant d’alimentation maximum 0,3 A
Alimentazione massima fornita 0,3 A
Max. voedingsstroom 0,3 A
AMP REM
ATT
Blue/white striped
Blauweiß gestreift
Rayé bleu/blanc
Rigato blu e bianco
Blauw/wit gestreept
BUS
CONTROL IN
3
5
1
4
See “Power connection diagram” on the reverse side for details.
4
Voir le « Schéma de raccordement d’alimentation » au verso pour
plus de détails.
Per ulteriori informazioni, vedere “Diagramma dei collegamenti di
alimentazione” che si trova sul retro.
Zie "Voedingsaansluitschema" op de achterkant voor meer details.
5
Yellow
Gelb
Jaune
Giallo
Geel
continuous power supply
permanente Stromversorgung
alimentation continue
alimentazione continua
continu voeding
7
Blue
Blau
Bleu
Blu
Blauw
power antenna (aerial) control
Motorantennensteuerung
antenne électrique
comando dell’antenna elettrica
elektrische antenne
8
2
8
Red
Rot
Rouge
Rosso
Rood
switched power supply
geschaltete Stromversorgung
alimentation commutée
alimentazione commutata
geschakelde voeding
3
Black
Schwarz
Noir
Nero
Zwart
ground (earth)
Masse
masse
terra
aarding
4
Positions 1, 2, 3, and 6 do not have pins.
An Position 1, 2, 3 und 6 be nden sich keine Stifte.
Les positions 1, 2, 3 et 6 ne comportent pas de broches.
Le posizioni 1, 2, 3 e 6 non hanno piedini.
De posities 1, 2, 3 en 6 hebben geen pins.
Connection diagram
This connection is only for amplifiers. Connecting any other
system may damage the unit.
B To the interface cable of a car telephone
Warning
If you have a power antenna (aerial) without a relay box,
connecting this unit with the supplied power connecting
lead 3 may damage the antenna (aerial).
Notes on the control and power suppy leads
• The power antenna (aerial) control lead (blue) supplies +12 V
DC when you turn on the tuner, or when you activate the AF
(Alternative Frequency) or TA (Traffic Announcement) function.
• When your car has built-in FM/MW/LW antenna (aerial) in the
rear/side glass, connect the power antenna (aerial) control
lead (blue) or the accessory power supply lead (red) to the
power terminal of the existing antenna (aerial) booster. For
details, consult your dealer.
• A power antenna (aerial) without a relay box cannot be used
with this unit.
Memory hold connection
When the yellow power supply lead is connected, power will
always be supplied to the memory circuit even when the ignition
switch is turned off.
Notes on speaker connection
• Before connecting the speakers, turn the unit off.
• Use speakers with an impedance of 4 to 8 ohms, and with
adequate power handling capacities to avoid its damage.
• Do not connect the speaker terminals to the car chassis, or
connect the terminals of the right speakers with those of the
left speaker.
• Do not connect the ground (earth) lead of this unit to the
negative (–) terminal of the speaker.
• Do not attempt to connect the speakers in parallel.
• Connect only passive speakers. Connecting active speakers
(with built-in amplifiers) to the speaker terminals may damage
the unit.
• To avoid a malfunction, do not use the built-in speaker leads
installed in your car if the unit shares a common negative (–)
lead for the right and left speakers.
• Do not connect the unit’s speaker leads to each other.
Note on connection
If speaker and amplifier are not connected correctly, “FAILURE”
appears in the display. In this case, make sure the speaker and
amplifier are connected correctly.
Anschlussdiagramm
A An AMP REMOTE IN des gesondert
erhältlichen Endverstärkers
Dieser Anschluss ist ausschließlich für Verstärker gedacht.
Schließen Sie nichts anderes daran an. Andernfalls kann
das Gerät beschädigt werden.
B An Schnittstellenkabel eines Autotelefons
Warnung
Wenn Sie eine Motorantenne ohne Relaiskästchen
verwenden, kann durch Anschließen dieses Geräts mit
dem mitgelieferten Stromversorgungskabel 3 die
Antenne beschädigt werden.
Hinweise zu den Steuer- und Stromversorgungsleitungen
• Die Motorantennen-Steuerleitung (blau) liefert +12 V
Gleichstrom, wenn Sie den Tuner einschalten oder die
AF- (Alternativfrequenzsuche) oder die TA-Funktion
(Verkehrsdurchsagen) aktivieren.
• Wenn das Fahrzeug mit einer in der Heck-/
Seitenfensterscheibe integrierten FM (UKW)/MW/LWAntenne ausgestattet ist, schließen Sie die MotorantennenSteuerleitung (blau) oder die Zubehörstromversorgungsleitung
(rot) an den Stromversorgungsanschluss des vorhandenen
Antennenverstärkers an. Näheres dazu erfahren Sie bei Ihrem
Händler.
• Es kann nur eine Motorantenne mit Relaiskästchen
angeschlossen werden.
Schémas de raccordement
A Au niveau du AMP REMOTE IN d’un
amplificateur de puissance facultatif
Speaker, Rear, Right
Lautsprecher hinten rechts
Haut-parleur, arrière, droit
Diffusore, posteriore, destro
Luidspreker, achter, rechts
5
Purple
Violett
Violet
Viola
Paars
–
Speaker, Rear, Right
Lautsprecher hinten rechts
Haut-parleur, arrière, droit
Diffusore, posteriore, destro
Luidspreker, achter, rechts
6
Gray
Grau
Gris
Grigio
Grijs
+
Speaker, Front, Right
Lautsprecher vorne rechts
Haut-parleur, avant, droit
Diffusore, anteriore, destro
Luidspreker, voor, rechts
7
–
Speaker, Front, Right
Lautsprecher vorne rechts
Haut-parleur, avant, droit
Diffusore, anteriore, destro
Luidspreker, voor, rechts
8
3
5
7
2
4
6
8
Schema di collegamento
A A AMP REMOTE IN di un amplificatore di
potenza opzionale
Ce raccordement existe seulement pour les amplificateurs.
Le raccordement à tout autre système peut endommager
l’appareil.
Questo collegamento è riservato esclusivamente agli
amplificatori. Non collegare un tipo di sistema diverso onde
evitare di causare danni all’apparecchio.
B Al cavo di interfaccia di un telefono per auto
Avertissement
Si vous disposez d’une antenne électrique sans boîtier
de relais, le branchement de cet appareil au moyen du
cordon d’alimentation fourni 3 risque d’endommager
l’antenne.
Remarques sur les câbles de commande et d’alimentation
• Le câble de commande (bleu) fournit du courant continu de
+12 V lorsque vous mettez le tuner sous tension ou lorsque
vous activez la fonction AF (fréquence alternative) ou TA
(messages de radioguidage).
• Lorsque votre voiture est équipée d’une antenne FM/MW
(GO)/LW (PO) intégrée dans la vitre arrière/latérale,
raccordez le câble de commande d’antenne (bleu) ou le
câble d’alimentation des accessoires (rouge) à la borne
d’alimentation de l’amplificateur d’antenne existant. Pour plus
de détails, consultez votre revendeur.
• Une antenne électrique sans boîtier de relais ne peut pas être
utilisée avec cet appareil.
Raccordement pour la conservation de la mémoire
Lorsque le câble d’alimentation jaune est connecté, le circuit
de la mémoire est alimenté en permanence même si la clé de
contact est en position d’arrêt.
Hinweise zum Lautsprecheranschluss
• Schalten Sie das Gerät aus, bevor Sie die Lautsprecher
anschließen.
• Verwenden Sie Lautsprecher mit einer Impedanz zwischen 4 und
8 Ohm und ausreichender Belastbarkeit. Ansonsten können die
Lautsprecher beschädigt werden.
• Verbinden Sie die Lautsprecheranschlüsse nicht mit dem
Wagenchassis und verbinden Sie auch nicht die Anschlüsse
des rechten mit denen des linken Lautsprechers.
• Verbinden Sie die Masseleitung dieses Geräts nicht mit dem
negativen (–) Lautsprecheranschluss.
• Versuchen Sie nicht, Lautsprecher parallel anzuschließen.
• An die Lautsprecheranschlüsse dieses Geräts dürfen nur
Passivlautsprecher angeschlossen werden. Schließen Sie
keine Aktivlautsprecher (Lautsprecher mit eingebauten
Verstärkern) an, da das Gerät sonst beschädigt werden
könnte.
• Um Fehlfunktionen zu vermeiden, verwenden Sie nicht die
im Fahrzeug installierten, integrierten Lautsprecherleitungen,
wenn am Ende eine gemeinsame negative (–) Leitung für den
rechten und den linken Lautsprecher verwendet wird.
• Verbinden Sie nicht die Lautsprecherkabel des Geräts
miteinander.
Remarques sur le raccordement des haut-parleurs
• Avant de raccorder les haut-parleurs, mettez l’appareil hors
tension.
• Utilisez des haut-parleurs ayant une impédance de 4 à 8 ohms
et une capacité adéquate sous peine de les endommager.
• Ne raccordez pas les bornes du système de haut-parleurs au
châssis de la voiture et ne pas connecter les bornes du hautparleur droit à celles du haut-parleur gauche.
• Ne raccordez pas le câble de mise à la masse de cet appareil
à la borne négative (–) du haut-parleur.
• Ne tentez pas de raccorder les haut-parleurs en parallèle.
• Connectez uniquement des haut-parleurs passifs. Le
raccordement de haut-parleurs actifs (avec des amplificateurs
intégrés) aux bornes des haut-parleurs pourrait endommager
l’appareil.
• Pour éviter tout problème de fonctionnement, n’utilisez pas les
câbles des haut-parleurs intégrés installés dans votre voiture
si l’appareil dispose d’un câble négatif commun (–) pour les
haut-parleurs droit et gauche.
• Ne raccordez pas entre eux les cordons des haut-parleurs de
l’appareil.
Remarque sur le raccordement
Si les haut-parleurs ne sont pas raccordés correctement, le
message « FAILURE » s’affiche. Dans ce cas, assurez-vous que
les haut-parleurs sont raccordés correctement.
White
Weifl
Blanc
Bianco
Wit
Green
Grün
Vert
Verde
Groen
+
Speaker, Front, Left
Lautsprecher vorne links
Haut-parleur, avant, gauche
Diffusore, anteriore, sinistro
Luidspreker, voor, links
–
Speaker, Front, Left
Lautsprecher vorne links
Haut-parleur, avant, gauche
Diffusore, anteriore, sinistro
Luidspreker, voor, links
+
Speaker, Rear, Left
Lautsprecher hinten links
Haut-parleur, arrière, gauche
Diffusore, posteriore, sinistro
Luidspreker, achter, links
–
Speaker, Rear, Left
Lautsprecher hinten links
Haut-parleur, arrière, gauche
Diffusore, posteriore, sinistro
Luidspreker, achter, links
Negative polarity positions 2, 4, 6, and 8 have striped leads.
An den negativ gepolten Positionen 2, 4, 6 und 8 befinden sich gestreifte Adern.
Les positions de polarité négative 2, 4, 6 et 8 sont dotées de cordons rayés.
Le posizioni a polarità negativa 2, 4, 6 e 8 hanno cavi rigati.
De posities voor negatieve polariteit (2, 4, 6 en 8) hebben gestreepte kabels.
B Vers le cordon de liaison d’un téléphone de
voiture
Stromversorgung des Speichers
Wenn die gelbe Stromversorgungsleitung angeschlossen ist,
wird der Speicher stets (auch bei ausgeschalteter Zündung) mit
Strom versorgt.
Hinweis zum Anschließen
Wenn die Lautsprecher nicht richtig angeschlossen sind,
erscheint „FAILURE“ im Display. Vergewissern Sie sich in diesem
Fall, dass die Lautsprecher richtig angeschlossen sind.
+
7
from the car’s power connector
vom Stromanschluss des Fahrzeugs
du connecteur d’alimentation de la voiture
dal connettore di alimentazione dell’auto
van de autovoedingsaansluiting
Näheres dazu finden Sie im „Stromanschlussdiagramm“. Blättern
Sie dazu bitte um.
1
from the car’s speaker connector
vom Lautsprecheranschluss des Fahrzeugs
du connecteur de haut-parleur de la voiture
dal connettore dei diffusori dell’auto
van de autoluidsprekeraansluiting
Light blue
Hellblau
Bleu ciel
Azzurro
Lichtblauw
A To AMP REMOTE IN of an optional power
amplifier
*1 Remarque sur le raccordement de
*1 Opmerking bij de antenne-aansluiting
l’antenne
Indien uw auto is uitgerust met een
Si votre antenne de voiture est de type
antenne van het type ISO (International
ISO (Organisation internationale de
Organization for Standardization),
normalisation), utilisez l’adaptateur fourni
moet u die aansluiten met behulp
2 pour la raccorder. Raccordez d’abord
van de bijgeleverde adapter 2. Sluit
l’antenne de voiture à l’adaptateur fourni
eerst de auto-antenne aan op de
et, ensuite, à la prise d’antenne de
bijgeleverde adapter en vervolgens de
l’appareil principal.
antennestekker op het hoofdtoestel.
*2 Cordon à broche RCA (non fourni)
*2 Tulpstekkersnoer (niet bijgeleverd)
*3 AUDIO OUT peut être commuté sur SUB *3 AUDIO OUT kan worden ingesteld
ou REAR. Pour obtenir plus de détails,
op SUB of REAR. Raadpleeg de
reportez-vous au mode d’emploi.
gebruiksaanwijzing voor meer informatie.
*1 Hinweis zum Anschließen der Antenne
*1 Nota per il collegamento dell’antenna
Wenn Ihre Autoantenne der ISO-Norm
Se l’antenna dell’auto è di tipo
(Internationale Normungsgemeinschaft)
ISO (International Organization for
entspricht, schließen Sie sie mithilfe des
Standardization), utilizzare l’adattatore
mitgelieferten Adapters 2 an. Verbinden
Sie zuerst die Autoantenne mit dem
2 in dotazione per collegarla. Collegare
mitgelieferten Adapter und verbinden Sie
prima l’antenna della macchina
diesen dann mit der Antennenbuchse
all’adattatore in dotazione, quindi
des Hauptgeräts.
collegarla alla presa dell’antenna
dell’apparecchio principale.
*2 Cinchkabel (nicht mitgeliefert)
*2 Cavo a piedini RCA (non in dotazione)
*3 AUDIO OUT kann zwischen SUB
und REAR umgeschaltet werden.
*3 AUDIO OUT può essere impostato
Näheres hierzu finden Sie in der
su SUB o su REAR. Per ulteriori
Bedienungsanleitung.
informazioni, consultare il manuale di
istruzioni per l’uso.
XA-C40
*2
*1 from car antenna (aerial)
Source selector
(not supplied)
Signalquellenwähler
(nicht mitgeliefert)
Sélecteur de source
(non fourni)
Selettore di fonte
(non in dotazione)
Bronkeuzeschakelaar
(niet bijgeleverd)
Avvertenza
Quando si collega l’apparecchio con il cavo di
alimentazione in dotazione 3, si potrebbe danneggiare
l’antenna elettrica se questa non dispone di scatola a relè.
Note sui cavi di controllo e di alimentazione
• Il cavo (blu) di controllo dell’antenna elettrica fornisce
alimentazione pari a +12 V CC quando si attiva il
sintonizzatore oppure la funzione TA (notiziario sul traffico) o
AF (frequenza alternativa).
• Se l’automobile è dotata di antenna FM/MW/LW incorporata
nel vetro posteriore/laterale, collegare il cavo (blu) di
controllo dell’antenna elettrica o il cavo (rosso) di ingresso
dell’alimentazione ausiliaria al terminale di alimentazione
dell’amplificatore di potenza dell’antenna esistente. Per ulteriori
informazioni, consultare il proprio fornitore.
• Non è possibile usare un’antenna elettrica senza scatola a relè
con questo apparecchio.
Collegamento per la conservazione della memoria
Quando il cavo di alimentazione giallo è collegato, viene sempre
fornita alimentazione al circuito di memoria anche quando
l’interruttore di accensione è spento.
Note sul collegamento dei diffusori
• Prima di collegare i diffusori spegnere l’apparecchio.
• Usare diffusori di impedenza compresa tra 4 e 8 ohm e con
capacità di potenza adeguata, altrimenti i diffusori potrebbero
venire danneggiati.
• Non collegare i terminali del sistema diffusori al telaio dell’auto
e non collegare i terminali del diffusore destro a quelli del
diffusore sinistro.
• Non collegare il cavo di terra di questo apparecchio al
terminale negativo (–) del diffusore.
• Non collegare i diffusori in parallelo.
• Assicurarsi di collegare soltanto diffusori passivi, poiché
il collegamento di diffusori attivi, dotati di amplificatori
incorporati, ai terminali dei diffusori potrebbe danneggiare
l’apparecchio.
• Per evitare problemi di funzionamento, non utilizzare i cavi dei
diffusori incorporati installati nell’automobile se l’apparecchio
condivide un cavo comune negativo (–) per i diffusori destro e
sinistro.
• Non collegare fra loro i cavi dei diffusori dell’apparecchio.
Nota sui collegamenti
Se il diffusore non è collegato correttamente, “FAILURE” viene
visualizzato nel display. In tal caso, accertarsi che il diffusore sia
collegato correttamente.
Aansluitschema
A Naar AMP REMOTE IN van een optionele
versterker
Deze aansluiting is alleen bedoeld voor versterkers. Door
een ander systeem aan te sluiten kan het apparaat worden
beschadigd.
B Naar het interface-snoer van een
autotelefoon
Waarschuwing
Indien u een elektrische antenne hebt zonder relaiskast,
kan het aansluiten van dit apparaat met de bijgeleverde
voedingskabel 3 de antenne beschadigen.
Opmerkingen over de bedienings- en voedingskabels
• De bedieningskabel van de elektrische antenne (blauw) levert
+12 V gelijkstroom wanneer u de tuner inschakelt of de AF
(alternatieve frequenties) of TA (verkeersinformatie) functie
activeert.
• Wanneer uw auto is uitgerust met een FM/MW/LW-antenne
in de achterruit/zijruit, moet u de bedieningskabel van de
elektrische antenne (blauw) of de voedingskabel van de
accessoires (rood) aansluiten op de voedingsingang van de
bestaande antenneversterker. Raadpleeg uw dealer voor meer
details.
• Met dit apparaat is het niet mogelijk een elektrische antenne
zonder relaiskast te gebruiken.
Instandhouden van het geheugen
Zolang de gele voedingskabel is aangesloten, blijft de
stroomvoorziening van het geheugen intact, ook wanneer de
contactschakelaar van de auto wordt uitgeschakeld.
Opmerkingen betreffende het aansluiten van de luidsprekers
• Zorg dat het apparaat is uitgeschakeld, alvorens de
luidsprekers aan te sluiten.
• Gebruik luidsprekers met een impedantie van 4 tot 8 Ohm
en let op dat die het vermogen van de versterker kunnen
verwerken. Als u dit niet doet, kunnen de luidsprekers ernstig
beschadigd raken.
• Verbind in geen geval de aardingskabel van de luidsprekers
met het chassis van de auto en sluit de aansluitingen van de
rechter- en linkerluidspreker niet op elkaar aan.
• Verbind de aarddraad van dit apparaat niet met de negatieve
(–) aansluiting van de luidspreker.
• Probeer nooit de luidsprekers parallel aan te sluiten.
• Sluit geen actieve luidsprekers (met ingebouwde versterkers)
aan op de luidsprekeraansluiting van dit apparaat. Dit zal
leiden tot beschadiging van de actieve luidsprekers. Sluit dus
altijd uitsluitend luidsprekers zonder ingebouwde versterker
aan.
• Om defecten te vermijden mag u de bestaande
luidsprekerbedrading in uw auto niet gebruiken wanneer er een
gemeenschappelijke negatieve (–) kabel is voor de rechter- en
linkerluidsprekers.
• Verbind de luidsprekerkabels niet met elkaar.
Opmerking over aansluiten
Als de luidspreker en versterker niet goed zijn aangesloten,
wordt "FAILURE" in het display weergegeven. In dit geval moet u
zorgen dat de luidspreker en versterker correct zijn aangesloten.
7
CDX-GT410U/GT414U
Ver. 1.1
SECTION 2
DISASSEMBLY
Note: This set can be disassemble according to the following sequence.
SET
2-1.
SUB PANEL (FL-U) ASSY
(Page 9)
2-2.
CD MECHANISM BLOCK
(Page 9)
2-3.
MAIN BOARD
(Page 10)
2-4.
SERVO BOARD
(Page 10)
2-5.
CHASSIS (T) SUB ASSY
(Page 11)
2-6.
ROLLER ARM ASSY
(Page 11)
2-7.
CHASSIS (OP) ASSY
(Page 12)
1. CHUCKING ARM SUB ASSY
(SUPPLEMENT-1 Page 1)
2. SLED MOTOR ASSY
3. OPTICAL PICK-UP SECTION
4. OPTICAL PICK-UP
8
CDX-GT410U/GT414U
Note: Follow the disassembly procedure in the numerical order given.
2-1. SUB PANEL (FL) ASSY
3 two claws
2 two claws
1 two screws
(+PTT 2.6 × 6)
4 sub panel (FL-U) assy
2-2. CD MECHANISM BLOCK
8 CD mechanism block
7 bracket (CD)
6 two screws
(+PTT 2.6 × 4)
3
2 screw
(+PTT 2.6 × 6)
4 CN350
1 screw
(+PTT 2.6 × 6)
5 CN352 (3P)
9
CDX-GT410U/GT414U
2-3. MAIN BOARD
2 two screws
(+PTT 2.6 × 8)
4 two screws
(+PTT 2.6 × 10)
5 two screws
(+P 2.6 × 8)
1 three screws
(+BTT 2.6 × 5)
6 two screws
(+PTT 2.6 × 10)
7 screw
(+P 2.6 × 10)
8 screw
(+PTT 2.6 × 10)
9 heat sink
0 MAIN board
3
insulating sheet
2-4. SERVO BOARD
WHT
RED
BLK
WHT
RED
BLK
RED
ORG
BLU
YEL
GRY
2 toothed lock screw
(M 1.7 × 2.5)
SERVO board
3 toothed lock screw
(M 1.7 × 2.5)
5 SERVO board
1 Remove the eleven solders.
4 optical pick-up (16 core)
(CN1)
claw
claw
10
CDX-GT410U/GT414U
2-5. CHASSIS (T) SUB ASSY
2 two precision screws
(+P 1.7 × 2.2)
1 two precision screws
(+P 1.7 × 2.2)
4 chassis (T) sub assy
3 claw
2-6. ROLLER ARM ASSY
5 roller arm assy
4 gear (RA1)
1 spring (RAL)
3 washer
2 spring (RAR)
11
CDX-GT410U/GT414U
Ver. 1.1
2-7. CHASSIS (OP) ASSY
6 chassis (OP) assy
1 tension spring (KF)
5
7 coil spring (damper) (natural)
8 coil spring (damper) (green)
4 slider (R)
3 lever (D)
2 gear (LE1)
12
CDX-GT410U/GT414U
SECTION 3
DIAGNOSIS FUNCTION
Description of the Diagnostics function:
4. Contents of each display mode
4-1. Reset count display mode
1. Setting the Diag display mode
With the power off, press the [4] button, [5] button, and [4] button
on the set body or the remote control (for more than 2 seconds)
in turn.
2. Canceling the Diag display mode
During the Diag function mode, press the [OFF] button.
3. Initial display in the Diag display mode.
Just when the Diag mode is entered, “reset count” is displayed.
The display mode is switched by each rotation of
SEEK +/M > or SEEK – /. m keys.
01
XX
Reset count
(in hexadecimal format)
Diag code
01: Reset count
4-2. Reset count by watchdog timer display mode
02
XX
Reset count
Reset count display
01
Diag code
02: Number of resets by watchdog timer
XX
4-3. Number of connected units display mode
Reset count by watchdog timer display
031
02
Number of connected units display
031
XXX
XX
XXX
Show the number of connected units for
CD-C, MD-C and XM respectively from
the rightmost (in hexadecimal format).
Recency of information
1-3: 1 represents the latest.
Diag code
03: Number of connected unit.
Operating hours display
04
XXXX
The display mode is switched by each rotation of [2/GP/ALBM+] or
[1/GP/ALBM--] keys during the number of connected units display
mode.
CD error information display
No. of connected units history 1 (latest) display
051
XX
031
XXX
OFFSET/FAILURE error display
No. of connected units history 2 display
061XXXXX
032
XXX
USB error information display
No. of connected units history 3 display
071
XX
033
XXX
4-4. Operating hours display mode
04
XXXX
Operating hours
Diag code
04: Operating hours
13
CDX-GT410U/GT414U
4-5. CD error information display mode
4-5-1. Error description
4-6. OFFSET/FAILURE error display mode
061XXXXX
051
XX
Error information
Error description Indication
Description
(in hexadecimal
1X
SERVO ERROR
format)
3X
LOADING ERROR
4X
TRACK JUMP
5X
TEXT ERROR
Diag code
FX
MECHA
ERROR
05: CD error information
Operating hours
Error description
(0: OFFSET, 1: FAILURE)
Diag code
06: OFFSET/FAILURE
[1/GP/ALBM--] keys during the OFFSET/FAILURE error display
mode.
4-5-2. Disc type and operating hours
051 XXXX
Disc type
Operating hours
Diag code
05: CD error information
Indication
0
1
2
3
8
F
OFFSET/FAILURE error history 1 (latest) display
Disc type
MP3
WMA
AAC
ATRAC
CD/DA
UNKNOWN
061XXXXX
OFFSET/FAILURE error history 2 display
062XXXXX
[1/GP/ALBM--] keys during the CD error information display mode.
OFFSET/FAILURE error history 3 display
063XXXXX
CD error info history 1 (latest)
Error description plus error details display
051
XX
CD error info history 1 (latest)
Disc type plus operating hours display
4-7. USB error information display mode
4-7-1. Error description
071
051 XXXX
CD error info history 2
052
XX
052 XXXX
053
XX
053 XXXX
14
XX
Error information
Error description
Indication
Description
(in hexadecimal
15
DEVICE ERROR
format)
FILE ERROR
17
(NO MUSIC)
1E
POWER ON ERROR
Diag code
1F
BOOT ERROR
07: USB error information
INVALID EJECT
3A
ERROR
43
READ ERROR
INVALID
44
FORMAT FILE
NOT SUPPORT
FA
DEVICE
HUB NOT
FB
SUPPORT
CDX-GT410U/GT414U
4-7-2. Disc type and operating hours
[1/GP/ALBM--] keys during the CD error information display mode.
071 XXXX
Operating hours
Diag code
07: USB error information
USB error info history 1 (latest)
071
XX
USB error info history 1 (latest)
071XXXXX
USB error info history 2
072
XX
072 XXXX
073
XX
073XXXXX
074
XX
074 XXXX
075
XX
075 XXXX
15
CDX-GT410U/GT414U
MEMO
16
CDX-GT410U/GT414U
SECTION 4
DIAGRAMS
4-1. BLOCK DIAGRAM — MAIN SECTION —
J652 (1/2)
L
BUS
AUDIO
IN
R
ELECTRONIC VOLUME
IC401
BUS-RCH
J652 (2/2)
BUS-RCH
2 BUS-LCH
1 BUS-RCH
CD-RCH
6 CD-LCH
5 CD-RCH
CD L
CD R
CD-RCH
A ATT
MUTE CONTROL
SWITCH
Q411,412
CD
MECHANISM
UNIT
(MG-101U)
(1/2)
9 AUX-LCH
7 AUX-RCH
TU-RCH
4 TU-LCH
3 TU-RCH
OUT-FL 25
11 IN RL
OUT-FR 26
OUT-RR 24
R-CH(FRONT)
R-CH(REAR)
MUTE
Q440
SCL
SDA
SCL 29
SDA 30
MUTE CONTROL
SWITCH
Q491,492
DR+6V
A+3.3V
4
FR+
12
FR–
3
RR+
11
RR–
R-CH
BATT
5
AMP-REM
6
ANT-REM
AMP REM 29
ANT REM 27
F901
MECHA+6V
BU+3.3V
BU+3.3V
16
VP 35
SYSTEM CONTROL
IC501 (1/2)
SERVO+3.3V
D+3.3V
CDMON
CDON
ZMUTE
WAKE UP
AUX R-CH
AUX
95
94
61
93
CDMON
CDON
Z MUTE
WAKE UP
TU1
(TUNER UNIT)
I2C SCK 33
I2C SIO 34
RL+
RL–
10
D491
MC RX
TXD
2
OUT RL+ 9
OUT RL– 7
MUTE
Q470
MC TX
RXD
J901
12 IN FL
AUDIO OUT
REAR/SUB
CN300
1
FL+
9
FL–
OUT FL+ 5
OUT FL– 3
MUTE 28
B/U CHECK
B/U CHECK
MUTE
Q432
OUT-RL 23
SYSRST
SYS RST
R
R-CH
I2C BUS CONTROLLED POWER AMP/
MULTIPLE VOLTAGE REGULATOR
IC300
AUX-RCH
WAKE UP
WAKE UP
R-CH
MUTE
Q401
CDON
CDMON
ZMUTE
CD ON
CDM ON
Z MUTE
L
SUBOUT-L 21
SUBOUT-R 22
BATT
BATT
SDA
SCL
2 SDA
4 SCL
SCL
SDA
16 BEEP
22 STB
25 DIAG
VOLATT 9
ATT 100
AUDIO+B
BU+B
SERVO3.3V
MECHA6V
PANEL+B
30
37
31
33
34
AUDIO+8.3V
BU+5V
SERVO+3.3V
MECHA+6V
PANEL+B
BEEP 7
L-CH 4
1 ANT R-CH 3
TUNER+5V
REG
Q3
E2PVDD 15
BU+3.3V
TU-SCL 13
TU-SDA 14
MC RX
MC TX
AUDIO+8.3V
VCC 10
VDD+5V 11
AMPSTB 8
TU-RCH
27 MC RX
28 MC TX
DIAG 5
AUDIO+8.3V
TELEPHONE ATTENATION
CHECK
Q701
TELATT 98
BU+3.3V
REG
IC681
BU+5V
39 VSM
12 TUATT
E2P SCL 16
E2P SDA 17
25 EEP CKO
24 EEP SIO
NOISE MASK
SWITCH
Q1
13 NSMASK
96
60
54
58
UNISO 59
12
11
10
8
9
BUSON
UNISCK
BUIN
UNISI
SYSRST 88
BUS IN
CLK IN
B/U-C
DATA OUT
DATA IN
BATT 3
BUS ON 1
38 QUALITY
53 TU ATTIN
B/U CHECK
SCL 11
SDA 12
SCL
SDA
16 MPX
INTN 15
VDDA 1
VDDD 7
TH400
D602
BATT
BATT
4
5
6
1
2
3
CNJ400
BUS
CONTROL IN
8
• R-CH is omitted due to same as L-CH.
• Signal Path
RESET
A
DISPLAY
SECTION
(Page 18)
56 DAVN
RDS+3.3V
SWITCH
Q50
BATTERY
CHECK
Q605
RST 2
RDS MODULATOR
IC50
9 XTI
TEST
7
CLK 4
DATA I/O 6
13 RST
D353
QUALITY 5
MUTE CON 8
X50
8.664MHz
TEL ATT
15
BUS INTERFACE
IC601
S-METER 6
TU MUTE 7
10 XTO
ACC
13
TESTIN 97
SCL
SDA
RDS OUT 9
7
ACCESSORY CHECK
Q702
ACCIN 99
SYSRST
J1
(ANTENNA)
: CD PLAY
: FM
: MW/LW
: AUX
BU+3.3V
26 RDS ON
CDX-GT410U/GT414U
17
17
CDX-GT410U/GT414U
4-2. BLOCK DIAGRAM — DISPLAY SECTION —
FL901
FLUORESCENT
INDICATOR TUBE
SYSTEM CONTROL
IC501 (2/2)
GRID1 20
41 KEYIN0
KEY MATRIX
LSW901,902
S901–904,906–915
40 KEYIN1
D503
KEY ACKNOWLEDGE
SWITCH
Q664
GRID2 19
FL SO 19
FL SCK 20
FL CS 18
14 DIO
12 CLK
10 CS
GRID3 16
17
3G •
18
52 KEYACK
FL VH+12V
6
2G •
42
48 AD ON
RE901
PUSH SELECT
FL DRIVE
Q883
ROTARY
ENCODER
31 RE-IN0
32 RE-IN1
LED DRIVE
Q991
Q1 40
LED DRIVE
Q992
Q2 39
RESET 15
VH 9
62 NOSESW
VDD(+3.3V) 5
LED841–847,
850–857,
861–864,
LSW901,902
LED941–947,
950–957,
961–963,
LSW901,902
FL DRIVE
Q881
1G 41
(VOLUME)
PANEL+B
FL DRIVE
Q882
PANEL+B
FL +12V
REG
IC801
BATT
VDD+3.3V
REG
IC972
PANEL+B
PANEL+B
XOUT 80
REMOTE CONTROL
SIGNAL RECEIVER
IC971
64 SIRCS
XIN 79
OSCOUT 83
MAIN
SECTION
OSCIN 82
A
X502
32.768kHz
1
F+ •
2
FL+3V
REG
IC802
D804
44
F– •
45
X501
18.432MHz
RESET
FL ON 89
(Page 17)
USB CONTROL
IC804
DC-DC CONVERTER
IC803
BU+3.3V
RESET
IC602
77 RESET
BATT
DD ON 90
S103
RESET
FSW OUT 75
1 VIN
SW 2
2
•
3
INV 5
4 /EN
5 /OC
7 EN
SHIFT
CONTROL
SWITCH
Q805
6 RT
IN
6
•
OUT 7
•
8
D801
FB 3
CN902
CD
MECHANISM
UNIT
(MG-101U)
(2/2)
FSW IN 10
USB ON 92
USB OVER 91
CDX-GT410U/GT414U
18
18
1 CN902
USB D–
USB D+
2
3
4
CDX-GT410U/GT414U
• NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
• Waveforms
— MAIN Board —
THIS NOTE IS COMMON FOR PRINTED WIRING
BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is
printed in each block.)
1
For schematic diagrams.
For printed wiring boards.
Note:
• All capacitors are in µF unless otherwise noted. (p: pF)
50 WV or less are not indicated except for electrolytics
and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
•
f
: internal component.
• C : panel designation.
Note:
• X : parts extracted from the component side.
• Y : parts extracted from the conductor side.
a
: Through hole.
•
: Pattern from the side which enables seeing.
•
(The other layers' patterns are not indicated.)
Note: The components identified by mark 0 or dotted line
with mark 0 are critical for safety.
Replace only with part number specified.
•
•
•
•
•
•
•
•
A : B+ Line.
B : B– Line.
H : adjustment for repair.
Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : FM
(
) : MW/LW
<
> : CD PLAY
∗ : Impossible to measure
Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production
tolerances.
Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production
tolerances.
Circled numbers refer to waveforms.
Signal path.
J : CD PLAY
F : FM
f : MW/LW
L : AUX
Caution:
Pattern face side:
(Side B)
Parts face side:
(Side A)
IC501 i; (XOUT)
0.8 Vp-p
32.768 kHz
0.2 V/DIV, 20 µsec/DIV
2
Parts on the pattern face side seen from the
pattern face are indicated.
Parts on the parts face side seen from the
parts face are indicated.
IC501 is (OSC IN)
1 Vp-p
C
Q
18.432 MHz
These are omitted
B E
0.5 V/DIV, 0.1 µsec/DIV
3
IC50 9 (XTI)
BE C
These are omitted
1.1 Vp-p
8.664 MHz
ECB
0.5 V/DIV, 0.1 µsec/DIV
These are omitted
CDX-GT410U/GT414U
19
19
CDX-GT410U/GT414U
4-3. PRINTED WIRING BOARD — MAIN SECTION —
2
1
: Uses unleaded solder.
3
4
5
6
7
8
9
10
11
12
13
14
J652
L
R
CNJ400
(BUS CONTROL IN)
-4
(CHASSIS)
D901
C329
R702
R709
R707
C705
C626
JC903
JW105
JW106
JC19
JW138
JC901
JC36
IC601
JW95
L403
JC33
R603
• Semiconductor Location
CN351
1
R615
JW110
C405
C412
C417
JW125
R563
C701
R708
C702
C703
JW65
C625
C316
JW127
JW126
R602
R601
JW122
L410
4
CD
MECHANISM
UNIT
CN101 (MG-101U)
C415
C801
C808
JC810
JW139
Q805
R891
C814
R820
7
1
IC802
5
D804
R591
C802
C804
1
IC801
5
C803
C951
JW118
C892
JC811
JW107
JW111
C819
R810
R809
C815
IC804
C816
R802
JW89
C806
L818
R912
S103
CN370
S103
RESET
X501
(Page 24)
CDX-GT410U/GT414U
20
R817
C811
JW113
IC803
R812
JW121
JW119
JC23
D105
R818
JW114
JW112
1
C807
JC909
JW86
JW120
R890
C812
JC906
JW104
JW115
R925
R816
C805
C402
JW92
JW91
R600
JW116
R803
R553
R924
JW136
JC912
JC17
JW84
JC910
JC914
C810
JW117
R351
C809
C891
L803
CN350
D353
JC913
R800
D802
R819
C401
X501
R917
JW94
JW93
R509
R526
C507
R910
C519
R815
C890
L406
D801
R814
R813
R811
JW81
JC907
R540
D503
L802
R401
R532 R533
R561
JW109
JW108
C419
R402
C921
J
TH400
D604
R611
R612
CN2
R926
R923
IC602
3
2
4
1
X502
R927
R519
R529
R517
R565
R616
JW123
JW7
L804
JW30
D102
R673
D602
R607
C601
R902
R903
R555
L409
L402
L411
L501
JW83
R913
Q664
R671
R503
C924
3
CN352
D502
JC24
R567
R504
R597
D106
R570
JC16
1
D606
C409
1
R672
R502
Q605
R606
JW100
50
R674
C512 C514
D110
D702
R706
D311
JW68
JW67
C314
JW128
JW80
R552
R592
R593
R557
IC
C515
C504 R510
R521
R522
C508
C501
D603
R604
D605
R901
L405
C510
C513
L300
JW103
JC902
JC905
C418
R403
R961
JW87
R534
JW22
C516
JC911
JW18
JW17
D107
D111
JC920
JW70
R536
C820
JC922
JW3
JC923
JW16
JW15
JC921
R952
C818
JW4
D101
C158
D156
D103
JW135
L805
C157
JW14
R595
JW13
JC928
JW134
JC924
D104
R596
D153
R152
R150
JW71
C502
R951
C159
JC926
JW72
JC38
BATT
D607
JW79
R551
R505
C704
D304
R568
JW73
R537
YEL
JW64
JW63
JW124
JW62
JW69
D308
D307
JW66
C313
C683
JW82
JC904
L401
C407
C509
R511
R598
D113
D112
JW5
D108
JC930
JC21
D707
L407
JW61
JW60
JW59
JW58
Q492
C491
Q491
R404
JW140
JC18
JW76
R916
JC935
JC932
JW11
JW12
JW19
JC929
R154
D151
D152
JW10
JW9
R58
JC927
R153
L151
R520
JC931
C57
R151
JW2
JW20
Q50
D109
C56
R523
R57
X50
JW8
R636 JW96
JC22
C403
R544
JC934
JW21
R155
C61
R558
IC50
L50
C54
JW78
JW77
JC938
JW85
JC936
R915
R559
R61
JC28
R914
R556
JW137
R60
R52
C55
JW56
C306
R411
JW25
JC933
L2
R54
D305
C623
C622
JW90
JC14
JW26
4
C600
C706
C707
R705
JW97
R710
R564
JW74
R573
JW28
JW29
JC12
C151
JW27
C152
C50
C52
JC29
C424
C303
C364
JC401
Q3
JW34
JW31
C153
L3
R53
JW57
R442
R462
C451
C431
C363
5
D706
JW99
JW75
JW88
C3
JC10
C953
R15
R55
JW1
Q401
JW35
L4
R7
C53
R531
R599
Q402
JW33
6
7
D303
JW98
C406
JW23
H
L1
1
JW102
JC705
Q701
D302
C315
JC1
Q411
JW32
C5
C51
R493
Q412
R6
C58
D491
R491
JW36
R10
R13
C624
JW42
C8
JW24
JC8
C493
C494
R918
C7
C2
R12
I
R485
JW133
R157
D2
C6
JC941
JC32
JW45
JW43
D312
IC681
C681
C471
JW44
R9
JC942
R451
C484
IC401
R156
R430
JC4
L901
JW46
R919
R8
JC940
C308
R470
2
D703
R703
D301
JC939
JW47
C461
R431
D704
R704
Q702
D309
D310
L902
R460
C454
R302
R440
JW41
R5 R3
JW40
JC5
JW39
Q1
R2
R4
JC9
R920
R452
R1
E
C485
C486
R354
C365
C905
R158
JW38
C1
C312
R701
JW55
R461
3
JW101
JW54
C473
R420
C361
C320
JW53
JW131
C362
JC943
D
F901
C301
8
C319
C472
R471
C304
IC300
JW52
C463
JW130
C305
CNJ400
C434
C318
C462
Q470
R355
C366
TU1
(TUNER UNIT)
R301
R447
C302
C421
JC11
Q432
Q452
R357
R472
JW132
R356
G
R421
Q460
JW48
C
C307
C441
R448
R358
F
C444
C426
CN300
C325 JW50
JW51
JW49 C309
C423
C452
C432
C445
Q420
B
C443
YEL
C330
C317
C413
C414
R449
Q440
R450
D306
-3
JC31
-2
JW129
R
-1
C682
L
JC30
J1
(ANTENNA)
A
AUDIO OUT
REAR/SUB
BUS
AUDIO IN
20
1-872-031-
11
Ref. No.
D2
D101
D102
D103
D104
D105
D106
D107
D108
D109
D110
D111
D112
D113
D151
D152
D153
D156
D301
D302
D303
D304
D305
D306
D307
D308
D309
D310
D311
D312
D353
D491
D502
D503
D602
D603
D604
D605
D606
D607
D702
Location
E-2
I-4
I-4
I-4
I-4
J-7
I-4
I-4
I-3
I-2
I-4
I-4
I-4
H-3
I-2
I-2
I-3
I-2
C-8
D-8
C-9
D-9
C-6
C-6
C-6
C-6
C-6
C-6
C-7
C-7
H-8
E-5
H-7
I-6
D-10
D-10
E-10
D-9
D-9
D-9
C-8
Ref. No.
D703
D704
D706
D707
D801
D802
D804
D901
Location
C-9
C-8
C-9
D-8
F-10
F-9
H-9
B-10
IC50
IC300
IC401
IC501
IC601
IC602
IC681
IC801
IC802
IC803
IC804
G-2
B-6
D-3
G-6
E-10
G-7
D-6
I-10
H-10
G-10
H-9
Q1
Q3
Q50
Q401
Q402
Q411
Q412
Q420
Q432
Q440
Q452
Q460
Q470
Q491
Q492
Q605
Q664
Q701
Q702
Q805
E-2
F-2
H-2
F-4
E-4
E-5
E-4
B-4
B-3
B-4
C-3
C-4
C-4
E-5
E-5
D-10
I-6
C-8
C-8
G-11
CDX-GT410U/GT414U
4-4. SCHEMATIC DIAGRAM — MAIN SECTION (1/3) — • Refer to page 26 for IC Block Diagrams.
C303
C302
JC939
L902
C325
C444
C424
JC940
C330
C306
JC29
JC30
C308
JC31
C301
C309
C304
IC B/D
C305
L901
C307
C317
IC300
R301
C319
C318
R302
C434
C320
C312
C313
C314
C707
C315
D707
D304
R701
D704
JC12
D302
D301
C454
C316
CN300
C706
D702
R705
R710
JC705
D706
R709
D312
D311
D310
D309
D308
D307
D306
D305
D303
D703
F901
D607
C704
R703
R702
JC33
Q701
C705
R704
L300
R491
D491
R493
JC8
IC602
Q491
C701
Q492
Q702
R707
JC32
C625
C626
IC681
R961
R599
C491
R706
C702
R708
C703
R600
JC1
R604
R603
D603
D602
Q605
TH400
C600
CNJ400
R612
JC22
R611
JC21
R616
C601
R606
JC36
JC909
R602
R607
R601
JC905
JC910
D606
JC19
C329
D901
D605
D604
IC B/D
R615
C683 C682 C681
R531
IC601
(Page 23)
CDX-GT410U/GT414U
21
21
C622 C623 C624
(Page 22)
CDX-GT410U/GT414U
• Refer to page 19 for Waveforms.
4-5. SCHEMATIC DIAGRAM — MAIN SECTION (2/3) — • Refer to page 26 for IC Block Diagrams.
J652
TU1
J1
R12
C443
C432
C413
C414
C1
C426 C423
C463
C462
C473
C472
Q470
Q460
Q440
Q452
C3
C2
JC942
JC941
R358
L4
C5
R4
Q432
R357
JC10
R1
Q1
R6
C6
R5
C7
R2
C905
JC5
JC9
JC11
R462
R471
R461
C471
C461
R448
R7
R3
C362
R472
C8
R9
JC943
Q420
R13
R8
D2
C445
C452
R447
R449
R355
R450
R421
R442
R451
R431
C421
C441
C451
C431
R354
R10
R356
Q3
L1
C366
C361
C365
IC B/D
IC B/D
IC50
IC401
C953
C486
R55
C50
C58
R15
R60
C484
(Page 21)
R918
C485
C51
R919
C52
Q50
L2
C53
R53
C55
L50
R420
R920
JC4
R460
R558
R470
Q412
C493
C57
X50
C54
L3
C56
R61
R158
R157
R156
R430
C494
R411
C61
R58
R452
R54
R52
R57
R440
R485
R151
JC28
Q411
Q402
C407
C406
C151
R155
R153
C159
R154
C158
R403
R404
JC401
C364
C153
C363
C152
JC927
R152
Q401
JC923
L151
R150
C157
D156
D151
D152
CN370
L805
C818
JC930
JC928
L804
JC926
D106
D107
JC931
JC924
JC929
D109
R952
D108
R913
R951
D153
(Page 25)
D113
D111
JC921
D112
JC922
JC920
D110
D105
R912
D104
D102
CN352
D101
C924
D103
L818
C820
(Page 23)
CDX-GT410U/GT414U
22
22
C921
CDX-GT410U/GT414U
• Refer to page 19 for Waveforms.
• Refer to page 27 for IC Block Diagrams.
4-6. SCHEMATIC DIAGRAM — MAIN SECTION (3/3) — • Refer to page 28 for IC Pin Description of IC501.
(Page 21)
(Page 22)
CN351
JC901
JC902
R901
CN350
C405
C417
R902
C412
C403
R555 L402
L409
R903
L407
L403
C409 C415
JC906
R402
L401
L410
C419
R401
C418
D502
L411
JC17
C519
D353
L405
R533
R553
JC904
R532
JC903
JC914
C509
R568
R598
R597
JC934
JC936
JC935
JC938
S103
R519
JC913
C507
R674
X502
R570
C508
C401
R672
X501
R561
JC912
Q664
JC24
R529
C402
R591
L406
R351
R910
R517
R565
R567
R509
R917
L501
D503
C514
JC16
R540
R673
R526
R927
R926
C510
R671
C502
JC23
R503
IC B/D
IC B/D
IC501
R925
R502
C512
R592
R593
IC801
IC802
C501
R505
R504
C513
R923
R809
L802
R924
R811
R810
D804
R520
R812
R636
C802
C805
JC18
C803 C804
C951
JC811
C515
IC B/D
R563
R819
IC804
C891
C814
Q805
R891
R800
R815
D802
R816
JC810
R818
C890
C811
R813
JC907
L803
R890
C812
D801
R814
C810
C816
R817
C815
C819
R802
R803
C892
CDX-GT410U/GT414U
23
23
R511
C504
R510
R914
R915
R916
R559
R556
R544
R557
JC14
R534
JC38
R536
R573
R551
R537
R820
C808
C516
JC932
IC803
C809
R522
R523
R521
JC911
R564
C806 C807
R552
C801
JC933
R596
R595
CDX-GT410U/GT414U
4-7. PRINTED WIRING BOARD — KEY SECTION —
7
LED946
R961
8
9
10
11
12
13
LED841
LED941
S901
LED842,942
(CD INDICATOR)
LED841,941,
S901
LED842
LED942
LSW901
R947
R847
D
IC971
LED847,947,
S907
MODE
LED850,950,
S908
DSPL/DIM
LED851,951,
S909
1/GP/ALBM–
LED852,952,
S910
2/GP/ALBM+
S912
LED853,953,
S911
3/REP
LED854,954,
S912
4/SHUF
S913
LED855,955,
S913
5
S914
LED957
LED857
LED956
LED856
R854
R954
LED955
LED954
LED953
S911
LED855
S910
LED854
S909
LED853
LED950
S908
IC971
R909
LED952
LED852
S907
R977
LED851
C974
LED951
LED947
LE
LED864
R908
LED850
R906
R907
D9
D9
LE
LED945
LED845
S906
C
LED845,945,
S906
PTY
6
S903
62
63
SEEK–
61
LED863
LSW902
LSW902
R861
R862
S904
B
LED961 L E D
8
LED944
LED844
R903
R943
R904
5
LED846,946,S903
SOURCE
LSW901
M >
SEEK+
LED861–864,
LED961–963
(RING ILLUMINATION)
LED862
S902
LED844,944,
S904
EQ3
4
LED943
R843
LED843
LED843,943,
S902
OFF
R902
A
3
LED846
2
LED847
1
: Uses unleaded solder.
R853
S915
11
R953
LED856,956,
S914
6/PAUSE
1-872-032-
LED857,957,
S915
AF/TA
(11)
• Semiconductor Location
D-4
I-11
LED841
LED842
LED843
A-13
B-7
A-1
Location
B-2
C-2
B-4
C-4
D-5
D-6
D-7
D-8
D-8
D-9
D-10
D-11
B-3
B-2
Ref. No.
LED863
LED864
LED941
LED942
LED943
LED944
LED945
LED946
LED947
LED950
LED951
LED952
LED953
LED954
Location
B-3
C-3
A-13
B-7
A-2
B-2
C-2
B-4
C-4
D-5
D-6
D-7
D-7
D-8
Ref. No.
LED955
LED956
LED957
LED961
LED962
LED963
Location
D-9
D-10
D-11
B-3
C-3
C-2
Q881
Q882
Q883
Q991
Q992
I-8
I-8
I-9
I-6
I-6
11
1-872-033- (11)
ORG
RED
FB902
IC971
IC972
Ref. No.
LED844
LED845
LED846
LED847
LED850
LED851
LED852
LED853
LED854
LED855
LED856
LED857
LED861
LED862
FB901
F
Location
I-10
I-9
I-10
I-10
I-10
H-9
H-4
FB903
E
Ref. No.
D903
D904
D905
D906
D907
D908
D971
BRN
11
(Page 20)
1-872-033- (11)
MAIN BOARD CN370
G
J901
AUX
R952
R852
R913
R951
R851
R911
R912
R850
R950
R910
R976
D971
R949
A
CN901
J
RE901
PUSH SELECT
(VOLUME)
RED
1
CN902
BRN
IC972
C976
C982
LF901
D953
R978
C975
D951
FB907
D907
R995
R994
D905
R993
R983
D904
R984
C979
D903
R989
R881
R883
R885
R882
FB905 FB904
D906
Q883
R988
R981
R884
Q882
R886
R888
R887
C977
Q992
D908
Q881
FB906
C981
3
R846
Q991
R971
FL901
FLUORESCENT INDICATOR TUBE
R889
4
R845
R945
RE901
5
R946
C992
R982
C991
D955
R915
R863
R962
R864
R848
R948
I
R922
RB901
R944
R844
R905
R849
2
1
R914
R901
H
R975
R921
CN902
2
3
4
ORG
C905
R841
R942 R842
R941
11
1-872-032- (11)
CDX-GT410U/GT414U
24
24
CDX-GT410U/GT414U
4-8. SCHEMATIC DIAGRAM — KEY SECTION —
R975
R941
R841
LED946
R943
R949
LED846
R843
R947
R953
R849
R951
R847
R851
R978
IC972
LED861
R853
LED961
R976
LED863
R977
R981
IC971
R842
R945
LED944
LED844
R946
LED841
LED941
R845
LED950
LED957
LED850
LSW901(1/2)
R846
LED951
LED857
LED853
LED953
R954
LED851
C976
R861
R961
C977
R863
D971
R942
LED862
R854
R983
C975
C974
R944
LED842
LED942
LED945
LED943
R844
LED947
LED845
R948
R952
R848
R950
LED847
R852
R850
LED956
LED954
LSW902(1/2)
LED952
LED843
R962
LED962
LED855
LED963
R984
C979
R864
LED856
LED854
R982
R862
LED864
LED852
LED955
R993
R994
R995
C982
C991
R889
R886
R887
C992
Q991
R888
Q992
Q883
R988
CN901
R885
R971
C981
Q882
D908
FB905
D906
FB904
R883
R884
D907
Q881
R882
D904
D903
D905
R881
(Page 22)
RE901
R901
R922
R921
FL901
R905
R904
S903
S904
R907
R908
R909
S907
S908
S909
S906
S902
R906
LSW902(2/2)
FB906
D955
FB907
CN902
R903
D953
S901
D951
R902
RB901
R913
R914
R915
S914
S915
S911
R912
S913
R911
S912
R910
S910
C905
LSW901(2/2)
LF901
FB902
J901
FB901
FB903
CDX-GT410U/GT414U
25
25
R989
CDX-GT410U/GT414U
• IC BLOCK DIAGRAMS
IC300 TDA8588AJ/N2/R1/M5 (AEP, UK MODEL) (MAIN Board (1/3))
IC300 TDA8588AJ/N2/R1 (RUSSIA MODEL) (MAIN Board (1/3))
IC601 BA8271F-E2 (MAIN Board (1/3))
TAB 1
BUS ON 1
BUS ON
SWITCH
RST 2
RESET
SWITCH
BATT 3
BATTERY
SWITCH
14 VCC
2 SDA
OUT-FL- 3
I2C BUS
4 SCL
FL
OUT-FL+ 5
6 VP2
13
12
11
10
RESET
BUS ON
CLK IN
BU IN
OUT-RL- 7
RL
8 PGND3
OUT-RL+ 9
PROTECTION/
DIAGNOSTIC
IN-RR 15
12 IN-FL
9 DATA IN
GND 7
8 DATA OUT
14 IN-FR
MUTE
S-GND 13
10 SVR
MUTE
IN-RL 11
CLK 4
VREF 5
DATA 6
16 BEEP
VP
OUT-RR+ 17
RR
18 PGND2
OUT-RR- 19
20 VP1
OUT-FR+ 21
FR
OUT-FR- 23
STANDBY/
MUTE
CHIP DETECT/
DIAGNOSTIC
24 PGND1
BATTERY
DETECTION
DIAG 25
IC401 BD3442FS-E2 (MAIN Board (2/3))
22 STB
TEMPERATURE
PROTECTION
ENABLE
LOGIC
BUS-RCH 1
VCC2
32 F2L
100k
26 RST
31 GND
ANT-REM 27
BUS-LCH 2
SWITCH
100k
TU-RCH 3
28 CRES
AMP-REM 29
INPUT
SELECTOR
INPUT
GAIN
VOLUME1
/MUTE
TREBLE
/BASS
/MIDDLE
I2C
BUS
LOGIC
100k
SWITCH
TU-LCH 4
30 AUDIO8.3V
MECH6V 33
VCC
32 GND
27 VCC
CD-LCH 6
34 PANEL+B
FADER
26 OUT-FR
250k
FADER
25 OUT-FL
250k
FADER
24 OUT-RR
FADER
23 OUT-RL
100k
EFFECT
AUX-RCH 7
REFERENCE
VOLTAGE
36 CBU
LOADDUMP
PROTECTION
29 SCL
100k
VP 35
REGULATOR
30 SDA
28 MUTE
100k
CD-RCH 5
REGULATOR
SERVO5V 31
B.UP+B 37
VOLUME2
AUX-GND 8
BACK-UP
SWITCH
AUX-LCH 9
250k
DS3-L 10
22 SUBOUT-R
DS1-L 11
FADER
DS2-L 12
LPF
21 SUBOUT-L
EBIAS 13
FADER
20 ADJ
DS2-R 14
DS1-R 15
DS3-R 16
CDX-GT410U/GT414U
26
26
19 SAOUT
SPECTRUM
ANALYZER
18 SADA
17 SACLK
CDX-GT410U/GT414U
IC50 TDA7333013TR (MAIN Board (2/3))
3
INTERPOLATOR
BAND PASS
FILTER
SINC4
FILTER
MPX
REF3 2
REF2 3
VSS 5
16 MPX
15 INTN
SDAOUT
SDAIN
TEST LOGIC
SCK
I C/SPI
&
INTERFACE SPI
PIN MUX'S
TESTREG
RAM
RDS
RDSREG BUFFER
INTN DEMODULATOR &
&
SYNCHRONIZATION
CONTROL
LOGIC
REF1 4
SIGMA DELTA
CONVERTER
SINC4REG
VDDA 1
2
14
13
12
11
CSN
SA_DATAOUT
SDA_DATAIN
SCL_CLK
2
TM 6
10 XTO
OSCILLATOR
VDDD 7
9 XTI
RESETN 8
IC801 NJM2387ADL3 (MAIN Board (3/3))
IC802 NJM2387ADL3 (MAIN Board (3/3))
CURRENT
LIMIT
OVERVOLTAGE
PROTECTION
THERMAL
PROTECTION
BANDGAP
REFERENCE
1
2
3
4
5
VIN
CONTROL
VOUT
VADJ
GND
27
CDX-GT410U/GT414U
IC803 BD9778HFP (MAIN Board (3/3))
VIN
TSD
DRIVER
LATCH
RESET
CURRENT
LIMIT
PWM
COMPARATOR
VREF
OSC
ERROR
AMP
SOFT
START
VREF
ON/OFF
L:OFF
H:ON
1
VIN
28
2
SW
3
PB
4
GND
5
INV
6
RT
7
EN
CDX-GT410U/GT414U
• IC PIN DESCRIPTION
IC501 MB90F046PF-G-101E1 (SYSTEM CONTROL) (MAIN BOARD (3/3))
Pin No.
Pin Name
I/O
Pin Description
1
AREASEL0
I
Destination setting pin 0
2
AREASEL1
I
3
AREASEL2
I
4
B-OUTSEL
I
Black-out with/without discrimination signal input
5
DIAG
I
Status signal input from power amplifier
6
AAC SEL
I
AAC play setting signal input
“H”: Black-out
7
BEEP
O
Beep signal output to power amplifier
8
AMPSTB
O
Standby signal output to power amplifier
9
VOLATT
O
Electronic volume attenuate control signal output
10
FSW IN
I
D/D converter oscillator frequency count signal input
11
VSS
—
Ground pin
12
TUATT
O
Tuner mute control signal output
13
NSMASK
O
Noise mask signal output
14
ILLUMI SEL
I
Illumination voltage setting signal input
15
COL SEL
I
Two colors change setting signal input
16, 17
NCO
O
Not used. (Open)
18
FL CS
O
Fluorescent indicator tube chip select signal output
19
FL SO
O
Fluorescent indicator tube serial data signal output
20
FL SCK
O
Fluorescent indicator tube serial clock signal output
21, 22
NCO
O
Not used. (Open)
23
VCC5
—
Power supply pin (+3.3 V)
24
EEP SIO
I/O
EEPROM bus serial data signal input/output
25
EEP CKO
O
EEPROM bus serial clock signal output
26
RDS ON
O
RDS (Radio Data System) on signal output
27
MC RX
I
Mechanism microcomputer comunication signal input RX
28
MC TX
O
Mechanism microcomputer comunication signal output TX
29, 30
NCO
O
Not used. (Open)
31
RE IN0
I
Rotary encoder signal input 0
32
RE IN1
I
Rotary encoder signal input 1
33
I2C SCK
O
I2C bus serial clock signal output
34
I2C SIO
I/O
I2C bus serial data signal input/output
35
DAVDD
—
A/D converter power supply pin (+3.3 V)
36
AVRH
—
A/D converter external reference power supply pin (+3.3 V)
37
DAVSS
—
Ground pin
38
QUALITY
I
Noise detect signal input
39
VSM
I
S-meter voltage detect signal input
40
KEYIN1
I
Key signal input 1
41
KEYIN0
I
Key signal input 0
42
VSS
—
Tuner on: “L”
Ground pin
43
RCIN0
I
Rotary commander key signal input
44 to 47
NCO
O
Not used. (open)
Not used in this set.
48
AD ON
O
A/D converter power supply control signal output
49
MD0
I
Operation mode setting pin (Connect to VDD.)
50
MD1
I
Operation mode setting pin (Connect to VDD.)
51
MD2
I
Operation mode setting pin (Connect to VSS.)
52
KEYACK
I
Key acknowledgment detect signal input
53
TUATTIN
I
Tuner mute zero cross detect signal input
54
BUIN
I
Back-up power supply detect signal input
29
CDX-GT410U/GT414U
Pin No.
Pin Name
I/O
55
NCO
O
Not used. (Open)
Pin Description
56
DAVN
I
RDS (Radio Data System) data block synchronized detect signal input
57
NCO
O
Not used. (Open)
58
UNISI
I
SONY bus data signal input
59
UNISO
O
SONY bus data signal output
60
UNISCK
O
SONY bus clock signal output
61
Z MUTE
I
Mute signal input
62
NOSE SW
I
Front panel attachment detect signal input
63
FLASH W
I
Memory mode change signal input
Normally “H”: Single chip mode, after reset
“L”: flash write mode
64
SIRCS
I
Remote control signal input
65 to 70
NCO
O
Not used. (Open)
71
RC IN1
I
Rotary commander shift key signal input
72 to 74
NCO
O
30
“L”: With panel, “H”: Without panel
Not used in this set.
Not used. (Open)
D/D converter oscillator frequency shift control signal output
75
FSW OUT
O
76
NCO
O
Not used. (Open)
77
RESET
I
CPU reset signal input
78
NCO (OPEN REQ)
O
Not used. (Open)
79
XIN
I
Low speed operation clock signal input (32.768 kHz)
80
XOUT
O
Low speed operation clock signal output (32.768 kHz)
81
VSS1
—
Ground pin
“L”: 350 kHz, “H”: 415 kHz
82
OSCIN
I
High speed operation clock signal input (18.432 MHz)
83
OSCOUT
O
High speed operation clock signal output (18.432 MHz)
84
VCC3
—
Power supply pin (+3.3 V)
85
CYRIL SEL
I
Cyril correspondence discrimination signal input
86
DEMOSEL
I
DEMO select signal input
87
NCO
O
Not used. (Open)
88
SYSRST
O
System reset signal output
“L”: No correspondence
“H”: DEMO on, “L”: DEMO off
89
FL ON
O
Fluorescent indicator tube power on/off control signal output
90
DD ON
O
D/D converter power on/off control signal output
91
USB OVER
I
USB overcurrent detection signal input
92
USB ON
O
USB overcurrent detection IC control signal output
“H”: On, “L”: Off
93
WAKE UP
O
Mechanism microcomputer wake up signal output
“H”: Wake up, “L”: Sleep
“L”: Overcurrent detection
94
CDON
I
CD mechanism servo power supply control request signal input
95
CDMON
I
CD mechanism deck power supply control request signal input
96
BUSON
O
Bus on signal output
97
TESTIN
I
Test mode detect signal input
98
TELATT
I
Telephone attenuate detect signal input
99
ACC IN
I
Accessory power supply detect signal input
100
ATT
O
Audio mute control signal output
CDX-GT410U/GT414U
SECTION 5
EXPLODED VIEWS
NOTE:
• The mechanical parts with no reference
number in the exploded views are not supplied.
• Items marked “*” are not stocked since
they are seldom required for routine service.
Some delay should be anticipated
when ordering these items.
•
•
•
5-1.
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
-XX and -X mean standardized parts, so
they may have some difference from the
original one.
Color Indication of Appearance Parts
Example :
KNOB, BALANCE (WHITE) ... (RED)
R
R
Parts Color Cabinet’s Color
Accessories are given in the last of this parts list.
•
Abbreviation
RU: Russia model
MAIN SECTION
not supplied
A
MG-101U-188//Q
#2
7
#1
#3
B
A
#4
#5
F901
#4
not supplied
4
#3
#6
#4
not supplied
5
not supplied
3
6
#1
TU1
not supplied
B
2
#1
not supplied
#1
1
Ref. No.
Part No.
Description
1
2
3
4
5
X-2149-438-1
3-042-244-11
X-2108-670-1
2-050-124-01
A-1215-203-A
PANEL (FL-U) ASSY, SUB
SCREW (T)
LOCK ASSY (S)
SCREW +BTT 2.6X5
MAIN BOARD, COMPLETE (AEP,UK)
Remark
5
6
7
A-1221-474-A MAIN BOARD, COMPLETE (RU)
2-021-848-01 SHEET (TU), GROUND
1-831-838-11 CORD (WITH CONNECTOR) (ISO) (POWER)
Ref. No.
Part No.
Description
F901
TU1
#1
#2
#3
1-532-877-11
A-3220-961-B
7-685-792-09
7-685-790-01
7-685-793-09
FUSE (BLADE TYPE) (AUTO FUSE) 10A
TUNER UNIT (TUX-032)
SCREW +PTT 2.6X6 (S)
#4
#5
#6
7-685-794-09 SCREW +PTT 2.6X10 (S)
7-685-134-19 SCREW +P 2.6X8 TYPE2 NON-SLIT
7-621-284-40 SCREW +P 2.6X10
Remark
31
CDX-GT410U/GT414U
5-2.
FRONT PANEL SECTION
57
56
RE901
57
not supplied
not supplied
(KEY board)
58
59
FL901
CN902
55
not supplied
not supplied
52
54
not supplied
not supplied
53
not supplied
(AUX board)
51
61
Ref. No.
51
Part No.
60
Description
Remark
51
51
52
A-1215-205-A PANEL COMPLETE ASSY, FRONT
(GT410U:AEP,UK)
A-1215-215-A PANEL COMPLETE ASSY, FRONT
(GT414U:AEP,UK)
A-1226-240-A PANEL COMPLETE ASSY, FRONT (GT410U:RU)
A-1228-536-A PANEL COMPLETE ASSY, FRONT (GT414U:RU)
X-2149-754-1 BUTTON ASSY (S) (GT410U)
52
53
53
54
X-2149-755-1
X-2149-758-1
X-2149-759-1
X-2149-353-1
51
32
BUTTON ASSY (S) (GT414U)
PANEL (SV) ASSY, FRONT (GT410U)
PANEL (SV) ASSY, FRONT (GT414U)
KNOB (VOL) (SV) ASSY
Ref. No.
Part No.
Description
55
56
57
58
59
2-693-599-01
2-686-937-01
3-250-543-21
X-2149-228-2
2-686-941-01
SPRING (RELEASE)
PANEL (FL-U), BACK
SCREW (+B P-TITE M2)
CASE ASSY (for FRONT PANEL)
HOLDER (USB)
Remark
60
61
CN902
FL901
RE901
2-686-945-01
3-251-320-01
1-820-877-11
1-519-909-12
1-479-481-13
CAP (USB)
EMBLEM (NO. 2.5), SONY
CONNECTOR, USB (SOCKET) (USB)
INDICATOR TUBE, FLUORESCENT
ENCODER, ROTARY (PUSH SELECT,VOLUME)
CDX-GT410U/GT414U
Ver. 1.1
5-3.
CD MECHANISM SECTION
(MG-101U-188//Q)
NOTE: Refer to SUPPLEMENT-1 for disassembly of OPTICAL PICK-UP.
101
102
not supplied
not supplied
103
#6
#6
105
not supplied
not supplied
not supplied
not supplied
not supplied
104
not supplied
not supplied
not supplied
not supplied
107
not supplied
Ref. No.
Part No.
Description
101
102
0 103
104
A-1177-168-A
A-1177-169-A
X-2149-672-1
2-626-869-01
MECHANICAL BLOCK ASSY
DAXEV//Q
SERVICE ASSY, OP (DAX-25A)
SCREW (M2X3), SERRATION
106
Remark
106
Ref. No.
105
106
107
#7
Part No.
Description
3-348-998-31
3-352-758-31
A-1206-357-A
7-627-000-08
SCREW (M1.4X2.5), TAPPING, PAN
SCREW (M1.7X2.5), TOOTHED LOCK
SERVO BOARD, COMPLETE
SCREW, PRECISION +P 1.7X2.2 TYPE3
Remark
33
CDX-GT410U/GT414U
AUX
SECTION 6
ELECTRICAL PARTS LIST
KEY
NOTE:
• Due to standardization, replacements in
the parts list may be different from the
parts specified in the diagrams or the
components used on the set.
• -XX and -X mean standardized parts, so
they may have some difference from the
original one.
• RESISTORS
All resistors are in ohms.
METAL:Metal-film resistor.
METAL OXIDE: Metal oxide-film resistor.
F:nonflammable
Ref. No.
Part No.
•
•
•
•
Items marked “*” are not stocked since
they are seldom required for routine service.
Some delay should be anticipated
when ordering these items.
SEMICONDUCTORS
In each case, u : µ, for example:
uA.. : µA.. uPA.. : µPA..
uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD..
CAPACITORS
uF : µF
COILS
uH : µH
Description
Remark
Ref. No.
FB906
FB907
AUX BOARD
**********
Part No.
When indicating parts by reference
number, please include the board.
•
Abbreviation
RU: Russia model
Description
1-216-295-11 SHORT CHIP
1-216-295-11 SHORT CHIP
Remark
0
0
< FLUORESCENT INDICATOR TUBE >
< FERRITE BEAD >
FB901
FB902
FB903
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
FL901
1-414-595-11 INDUCTOR, FERRITE BEAD
1-519-909-12 INDICATOR TUBE, FLUORESCENT
< IC >
IC971
IC972
< JACK >
6-600-163-01 IC RS-770 (IR)
6-706-715-01 IC NJM2867F33(TE2)
J901
1-819-732-21 JACK (DIA. 3.5) (AUX)
*************************************************************
KEY BOARD
**********
< CAPACITOR >
C905
C974
C975
C976
C977
1-162-970-11
1-107-826-11
1-107-826-11
1-107-826-11
1-125-891-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.1uF
0.1uF
0.1uF
0.47uF
10%
10%
10%
10%
10%
25V
16V
16V
16V
10V
C979
C981
C982
C991
C992
1-127-715-11
1-107-826-11
1-107-826-11
1-162-970-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.22uF
0.1uF
0.1uF
0.01uF
0.01uF
10%
10%
10%
10%
10%
16V
16V
16V
25V
25V
< DIODE >
LED841
LED842
LED843
LED844
LED845
8-719-078-21
8-719-078-21
8-719-078-21
8-719-078-21
8-719-078-21
LED
LED
LED
LED
LED
SML-310PTT86 (Z)
SML-310PTT86 (CD INDICATOR)
SML-310PTT86 (OFF)
SML-310PTT86 (EQ3)
SML-310PTT86 (PTY)
LED846
LED847
LED850
LED851
LED852
8-719-078-21
8-719-078-21
8-719-078-21
8-719-078-21
8-719-078-21
LED
LED
LED
LED
LED
SML-310PTT86 (SOURCE)
SML-310PTT86 (MODE)
SML-310PTT86 (DSPL/DIM)
SML-310PTT86 (1/GP/ALBM–)
SML-310PTT86 (2/GP/ALBM+)
LED853
LED854
LED855
LED856
LED857
8-719-078-21
8-719-078-21
8-719-078-21
8-719-078-21
8-719-078-21
LED
LED
LED
LED
LED
SML-310PTT86 (3/REP)
SML-310PTT86 (4/SHUF)
SML-310PTT86 (5)
SML-310PTT86 (6/PAUSE)
SML-310PTT86 (AF/TA)
LED861
LED862
LED863
LED864
LED941
8-719-078-21
8-719-078-21
8-719-078-21
8-719-078-21
8-719-053-09
LED
LED
LED
LED
LED
SML-310PTT86 (RING ILLUMINATION)
SML-310VTT86 (Z)
LED942
LED943
LED944
LED945
LED946
8-719-053-09
8-719-053-09
8-719-053-09
8-719-053-09
8-719-053-09
LED
LED
LED
LED
LED
SML-310VTT86 (CD INDICATOR)
SML-310VTT86 (OFF)
SML-310VTT86 (EQ3)
SML-310VTT86 (PTY)
SML-310VTT86 (SOURCE)
LED947
LED950
LED951
LED952
LED953
8-719-053-09
8-719-053-09
8-719-053-09
8-719-053-09
8-719-053-09
LED
LED
LED
LED
LED
SML-310VTT86 (MODE)
SML-310VTT86 (DSPL/DIM)
SML-310VTT86 (1/GP/ALBM–)
SML-310VTT86 (2/GP/ALBM+)
SML-310VTT86 (3/REP)
< CONNECTOR >
CN901
1-820-620-11 PLUG, CONNECTOR 24P
< DIODE >
D903
D904
D905
D906
D907
8-719-057-80
8-719-057-80
8-719-977-12
8-719-977-12
8-719-977-12
DIODE
DIODE
DIODE
DIODE
DIODE
MA8180-M-TX
MA8180-M-TX
DTZ6.8B
DTZ6.8B
DTZ6.8B
D908
D951
D953
D955
D971
8-719-977-12
1-804-988-21
1-804-988-21
1-804-988-21
8-719-420-90
DIODE DTZ6.8B
VARISTOR, CHIP (1608)
DIODE MA8051-M
< FERRITE BEAD >
FB904
FB905
34
LED954 8-719-053-09 LED SML-310VTT86 (4/SHUF)
LED955 8-719-053-09 LED SML-310VTT86 (5)
LED956 8-719-053-09 LED SML-310VTT86 (6/PAUSE)
CDX-GT410U/GT414U
KEY
Ref. No.
LED957
LED961
LED962
LED963
Part No.
Description
8-719-053-09
8-719-053-09
8-719-053-09
8-719-053-09
LED
LED
LED
LED
Remark
Part No.
Description
R910
R911
R912
R913
R914
1-216-823-11
1-216-824-11
1-216-825-11
1-216-827-11
1-216-828-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1.5K
1.8K
2.2K
3.3K
3.9K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R915
R921
R922
R941
R942
1-216-830-11
1-216-295-11
1-216-295-11
1-216-813-11
1-216-813-11
METAL CHIP
SHORT CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
5.6K
0
0
220
220
5%
1/10W
5%
5%
1/10W
1/10W
< TRANSISTOR >
R943
R944
R945
R946
R947
1-216-812-11
1-216-811-11
1-216-812-11
1-216-811-11
1-216-812-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
180
150
180
150
180
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
R948
R949
R950
R951
R952
1-216-811-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
150
100
100
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R953
R954
R961
R962
R971
1-216-812-11
1-216-811-11
1-216-809-11
1-216-809-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
180
150
100
100
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R975
R976
R977
R978
R981
1-216-811-11
1-216-811-11
1-216-809-11
1-216-864-11
1-218-893-11
METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
150
150
100
0
82K
5%
5%
5%
1/10W
1/10W
1/10W
0.5%
1/10W
R982
R983
R984
R988
R989
1-216-841-11
1-216-801-11
1-216-801-11
1-216-864-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
47K
22
22
0
100K
5%
5%
5%
1/10W
1/10W
1/10W
5%
1/10W
R993
R994
R995
1-216-809-11 METAL CHIP
1-216-809-11 METAL CHIP
1-216-809-11 METAL CHIP
100
100
100
5%
5%
5%
1/10W
1/10W
1/10W
SML-310VTT86 (AF/TA)
SML-310VTT86 (RING ILLUMINATION)
Ref. No.
Remark
< COIL >
LF901
1-457-223-11 COIL, COMMON MODE CHOKE
< SWITCH >
LSW901 1-798-018-11 SWITCH, TACTILE (WITH LED)
(M > SEEK +)
LSW902 1-798-018-11 SWITCH, TACTILE (WITH LED)
(. m SEEK –)
Q881
Q882
Q883
Q991
Q992
8-729-600-22
8-729-600-22
8-729-600-22
6-550-752-01
6-550-752-01
2SA1235-F
2SA1235-F
2SA1235-F
DTC614TKT146
DTC614TKT146
< RESISTOR >
R841
R842
R843
R844
R845
1-216-810-11
1-216-810-11
1-216-811-11
1-216-810-11
1-216-811-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
120
120
150
120
150
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R846
R847
R848
R849
R850
1-216-810-11
1-216-811-11
1-216-810-11
1-216-807-11
1-216-807-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
120
150
120
68
68
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R851
R852
R853
R854
R861
1-216-807-11
1-216-807-11
1-216-811-11
1-216-810-11
1-216-811-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
68
68
150
120
150
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R862
R863
R864
R881
R882
1-216-810-11
1-216-811-11
1-216-810-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
120
150
120
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R883
R884
R885
R886
R887
1-216-821-11
1-216-833-11
1-216-833-11
1-216-833-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
10K
10K
10K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
RE901
R888
R889
R901
R902
R903
1-216-845-11
1-216-845-11
1-216-820-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
100K
820
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
S901
S902
S903
S904
S906
1-786-653-21
1-786-653-21
1-786-653-21
1-786-653-21
1-786-653-21
SWITCH, TACTILE (Z)
SWITCH, TACTILE (OFF)
SWITCH, TACTILE (SOURCE)
SWITCH, TACTILE (EQ3)
SWITCH, TACTILE (PTY)
R904
R905
R906
R907
R908
1-216-822-11
1-216-823-11
1-216-820-11
1-216-821-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1.2K
1.5K
820
1K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
S907
S908
S909
S910
S911
1-786-653-21
1-786-653-21
1-786-653-21
1-786-653-21
1-786-653-21
SWITCH, TACTILE (MODE)
SWITCH, TACTILE (DSPL/DIM)
SWITCH, TACTILE (1/GP/ALBM–)
SWITCH, TACTILE (2/GP/ALBM+)
SWITCH, TACTILE (3/REP)
R909
1-216-822-11 METAL CHIP
1.2K
5%
1/10W
S912
1-786-653-21 SWITCH, TACTILE (4/SHUF)
< NETWORK RESISTOR >
RB901
1-239-662-81 RESISTOR, NETWORK 10X2
< ROTARY ENCODER >
1-479-481-13 ENCODER, ROTARY (PUSH SELECT,VOLUME)
< SWITCH >
35
CDX-GT410U/GT414U
KEY
Ref. No.
MAIN
Part No.
Description
Remark
S913
1-786-653-21 SWITCH, TACTILE (5)
S914
1-786-653-21 SWITCH, TACTILE (6/PAUSE)
S915
1-786-653-21 SWITCH, TACTILE (AF/TA)
*************************************************************
A-1215-203-A MAIN BOARD, COMPLETE (AEP,UK)
A-1221-474-A MAIN BOARD, COMPLETE (RU)
*********************
7-621-284-40 SCREW +P 2.6X10
7-685-134-19 SCREW +P 2.6X8 TYPE2 NON-SLIT
7-685-794-09 SCREW +PTT 2.6X10 (S)
< CAPACITOR >
C1
C2
C3
C5
C6
1-126-963-11
1-126-947-11
1-162-970-11
1-124-589-11
1-162-970-11
ELECT
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
4.7uF
47uF
0.01uF
47uF
0.01uF
20%
20%
10%
20%
10%
50V
35V
25V
16V
25V
C7
C8
C50
C51
C52
1-162-970-11
1-162-970-11
1-107-826-11
1-107-826-11
1-107-826-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.01uF
0.1uF
0.1uF
0.1uF
10%
10%
10%
10%
10%
25V
25V
16V
16V
16V
C53
C54
C55
C56
C57
1-107-826-11
1-107-826-11
1-107-826-11
1-164-237-11
1-164-237-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.1uF
0.1uF
0.1uF
16PF
16PF
10%
10%
10%
5%
5%
16V
16V
16V
50V
50V
C58
C61
C151
C152
C153
1-162-959-11
1-126-947-11
1-126-960-11
1-126-960-11
1-126-961-11
CERAMIC CHIP
ELECT
ELECT
ELECT
ELECT
330PF
47uF
1uF
1uF
2.2uF
5%
20%
20%
20%
20%
50V
35V
50V
50V
50V
C157
C158
C159
C301
C302
1-163-009-11
1-163-017-00
1-163-017-00
1-115-340-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.0047uF
0.0047uF
0.22uF
0.01uF
10%
10%
10%
10%
10%
50V
50V
50V
25V
25V
C303
C304
C305
C306
C307
1-128-551-11
1-115-340-11
1-162-970-11
1-124-233-11
1-162-970-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
22uF
0.22uF
0.01uF
10uF
0.01uF
20%
10%
10%
20%
10%
63V
25V
25V
16V
25V
C308
C309
C312
C313
C314
1-124-233-11
1-115-340-11
1-115-340-11
1-162-970-11
1-124-233-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
10uF
0.22uF
0.22uF
0.01uF
10uF
20%
10%
10%
10%
20%
16V
25V
25V
25V
16V
C315
C316
C317
C318
C319
1-162-970-11
1-124-233-11
1-125-889-11
1-162-923-11
1-127-715-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
10uF
2.2uF
47PF
0.22uF
10%
20%
10%
5%
10%
25V
16V
10V
50V
16V
C320
C325
C329
C330
C361
1-162-970-11
1-115-340-11
1-107-826-11
1-115-340-11
1-127-715-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.22uF
0.1uF
0.22uF
0.22uF
10%
10%
10%
10%
10%
25V
25V
16V
25V
16V
36
Ref. No.
Part No.
Description
C362
C363
C364
C365
C366
1-127-715-11
1-126-160-11
1-126-160-11
1-126-960-11
1-126-960-11
CERAMIC CHIP
ELECT
ELECT
ELECT
ELECT
0.22uF
1uF
1uF
1uF
1uF
10%
20%
20%
20%
20%
16V
50V
50V
50V
50V
Remark
C401
C402
C403
C405
C406
1-124-234-00
1-162-970-11
1-124-584-00
1-124-234-00
1-124-257-00
ELECT
CERAMIC CHIP
ELECT
ELECT
ELECT
22uF
0.01uF
100uF
22uF
2.2uF
20%
10%
20%
20%
20%
16V
25V
10V
16V
50V
C407
C409
C412
C413
C414
1-124-257-00
1-124-233-11
1-162-970-11
1-163-251-11
1-163-251-11
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
2.2uF
10uF
0.01uF
100PF
100PF
20%
20%
10%
5%
5%
50V
16V
25V
50V
50V
C415
C417
C418
C419
C421
1-162-970-11
1-162-970-11
1-162-964-11
1-162-964-11
1-126-964-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
0.01uF
0.01uF
0.001uF
0.001uF
10uF
10%
10%
10%
10%
20%
25V
25V
50V
50V
50V
C423
C424
C426
C431
C432
1-165-908-11
1-162-927-11
1-165-908-11
1-126-964-11
1-163-251-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
1uF
100PF
1uF
10uF
100PF
10%
5%
10%
20%
5%
10V
50V
10V
50V
50V
C434
C441
C443
C444
C445
1-162-927-11
1-126-964-11
1-165-908-11
1-162-927-11
1-165-908-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
100PF
10uF
1uF
100PF
1uF
5%
20%
10%
5%
10%
50V
50V
10V
50V
10V
C451
C452
C454
C461
C462
1-126-964-11
1-163-251-11
1-162-927-11
1-126-964-11
1-165-908-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
10uF
100PF
100PF
10uF
1uF
20%
5%
5%
20%
10%
50V
50V
50V
50V
10V
C463
C471
C472
C473
C484
1-165-908-11
1-126-964-11
1-165-908-11
1-165-908-11
1-107-826-11
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
1uF
10uF
1uF
1uF
0.1uF
10%
20%
10%
10%
10%
10V
50V
10V
10V
16V
C485
C486
C491
C493
C494
1-126-933-11
1-126-964-11
1-124-589-11
1-162-967-11
1-162-967-11
ELECT
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
100uF
10uF
47uF
0.0033uF
0.0033uF
20%
20%
20%
10%
10%
16V
50V
16V
50V
50V
C501
C502
C504
C507
C508
1-162-970-11
1-162-964-11
1-162-970-11
1-162-917-11
1-162-917-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.001uF
0.01uF
15PF
15PF
10%
10%
10%
5%
5%
25V
50V
25V
50V
50V
C509
C510
C512
C513
C514
1-164-227-11
1-165-908-11
1-162-964-11
1-162-970-11
1-162-964-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.022uF
1uF
0.001uF
0.01uF
0.001uF
10%
10%
10%
10%
10%
25V
10V
50V
25V
50V
C515
C516
C519
1-162-970-11 CERAMIC CHIP
0.01uF
0.01uF
0.1uF
10%
10%
10%
25V
25V
16V
CDX-GT410U/GT414U
MAIN
Ref. No.
Part No.
Description
Part No.
Description
C600
C601
C622
C623
C624
1-126-935-11
1-162-970-11
1-126-924-11
1-126-916-11
1-124-584-00
ELECT
CERAMIC CHIP
ELECT
ELECT
ELECT
470uF
0.01uF
330uF
1000uF
100uF
20%
10%
20%
20%
20%
16V
25V
10V
6.3V
10V
Remark
Ref. No.
D106
D107
D108
D109
D110
8-719-977-12
8-719-977-12
8-719-977-12
8-719-977-12
8-719-977-12
DIODE
DIODE
DIODE
DIODE
DIODE
C625
C626
C681
C682
C683
1-124-584-00
1-124-584-00
1-162-970-11
1-162-970-11
1-124-584-00
ELECT
ELECT
CERAMIC CHIP
CERAMIC CHIP
ELECT
100uF
100uF
0.01uF
0.01uF
100uF
20%
20%
10%
10%
20%
10V
10V
25V
25V
10V
D111
D112
D113
D151
D152
8-719-977-12
8-719-977-12
8-719-977-12
1-805-043-11
1-805-043-11
DIODE DTZ6.8B
DIODE DTZ6.8B
DIODE DTZ6.8B
ABSORBER, CHIP SURGE
ABSORBER, CHIP SURGE
C701
C702
C703
C704
C705
1-131-868-81
1-164-005-11
1-164-005-11
1-115-340-11
1-115-340-11
ELECT
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
3300uF
0.47uF
0.47uF
0.22uF
0.22uF
20%
10%
10%
16V
25V
25V
25V
25V
D153
D156
D301
D302
D303
8-719-057-80
8-719-977-12
6-500-522-01
6-500-522-01
6-500-522-01
DIODE
DIODE
DIODE
DIODE
DIODE
MA8180-M-TX
DTZ6.8B
10EDB40-TA1B2
10EDB40-TA1B2
10EDB40-TA1B2
C706
C707
C801
C802
C803
1-163-009-11
1-163-009-11
1-126-933-11
1-107-826-11
1-124-589-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
ELECT
0.001uF
0.001uF
100uF
0.1uF
47uF
10%
10%
20%
10%
20%
50V
50V
16V
16V
16V
D304
D305
D306
D307
D308
6-500-522-01
6-500-522-01
6-500-522-01
6-500-522-01
6-500-522-01
DIODE
DIODE
DIODE
DIODE
DIODE
10EDB40-TA1B2
10EDB40-TA1B2
10EDB40-TA1B2
10EDB40-TA1B2
10EDB40-TA1B2
C804
C805
C806
C807
C808
1-162-970-11
1-107-826-11
1-124-589-11
1-162-970-11
1-162-970-11
CERAMIC CHIP
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
0.01uF
0.1uF
47uF
0.01uF
0.01uF
10%
10%
20%
10%
10%
25V
16V
16V
25V
25V
D309
D310
D311
D312
D353
6-500-522-01
6-500-522-01
6-500-522-01
6-500-522-01
6-501-013-01
DIODE
DIODE
DIODE
DIODE
DIODE
10EDB40-TA1B2
10EDB40-TA1B2
10EDB40-TA1B2
10EDB40-TA1B2
BAT54ALT1G
C809
C810
C811
C812
C814
1-126-933-11
1-162-970-11
1-124-584-00
1-162-969-11
1-107-826-11
ELECT
CERAMIC CHIP
ELECT
CERAMIC CHIP
CERAMIC CHIP
100uF
0.01uF
100uF
0.0068uF
0.1uF
20%
10%
20%
10%
10%
16V
25V
10V
25V
16V
D491
D502
D503
D602
D603
8-719-988-61
8-719-060-48
8-719-988-61
8-719-057-80
8-719-422-64
DIODE
DIODE
DIODE
DIODE
DIODE
1SS355TE-17
RB751V-40TE-17
1SS355TE-17
MA8180-M-TX
MA8062-M
C815
C816
C818
C819
C820
1-126-933-11
1-162-970-11
1-126-933-11
1-126-933-11
1-165-908-11
ELECT
CERAMIC CHIP
ELECT
ELECT
CERAMIC CHIP
100uF
0.01uF
100uF
100uF
1uF
20%
10%
20%
20%
10%
16V
25V
16V
16V
10V
D604
D605
D606
D607
D702
8-719-057-80
8-719-057-80
8-719-072-70
6-501-571-01
8-719-057-80
DIODE
DIODE
DIODE
DIODE
DIODE
MA8180-M-TX
MA8180-M-TX
MA2ZD14001S0
1N5404-C311-3
MA8180-M-TX
C890
C891
C892
C905
C921
1-162-964-11
1-162-964-11
1-165-908-11
1-162-964-11
1-165-908-11
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
CERAMIC CHIP
0.001uF
0.001uF
1uF
0.001uF
1uF
10%
10%
10%
10%
10%
50V
50V
10V
50V
10V
D703
D704
D706
D707
D801
8-719-977-12
8-719-057-80
8-719-057-80
8-719-057-80
8-719-420-90
DIODE
DIODE
DIODE
DIODE
DIODE
DTZ6.8B
MA8180-M-TX
MA8180-M-TX
MA8180-M-TX
MA8051-M
C924
C951
C953
1-216-864-11 SHORT CHIP
1uF
1uF
0
10%
10%
10V
10V
D802
D804
D901
6-501-657-01 DIODE MA24D5000BS0
6-500-522-01 DIODE 10EDB40-TA1B2
8-719-057-80 DIODE MA8180-M-TX
< CONNECTOR >
CN300
CN350
CN352
CN370
CNJ400
1-774-701-21
1-820-611-11
1-564-719-11
1-820-621-11
1-580-907-41
< IC >
PIN, CONNECTOR 16P
CONNECTOR, BOARD TO BOARD 28P
PIN, CONNECTOR (SMALL TYPE) 3P
SOCKET, CONNECTOR 24P
PLUG, CONNECTOR 8P (BUS CONTROL IN)
IC50
IC300
IC300
IC401
IC501
6-803-747-01
6-705-359-02
6-705-359-11
6-710-065-01
6-807-100-01
IC
IC
IC
IC
IC
TDA7333013TR
TDA8588AJ/N2/R1 (RU)
TDA8588AJ/N2/R1/M5 (AEP,UK)
BD3442FS-E2
MB90F046PF-G-101E1
< DIODE >
IC601
IC602
IC681
IC801
IC802
6-703-884-01
6-709-458-01
6-704-529-01
6-709-213-01
6-709-213-01
IC
IC
IC
IC
IC
BA8271F-E2
XC61CN2802NR
XC6206P332PR
NJM2387ADL3(TE2)
NJM2387ADL3(TE2)
IC803
IC804
6-707-911-01 IC BD9778HFP
6-710-624-01 IC TPS2051BDRG4
D2
D101
D102
D103
D104
8-719-977-03
8-719-988-61
8-719-988-61
8-719-977-12
8-719-977-12
DIODE
DIODE
DIODE
DIODE
DIODE
DTZ5.6B
1SS355TE-17
1SS355TE-17
DTZ6.8B
DTZ6.8B
D105
8-719-977-12 DIODE DTZ6.8B
Remark
DTZ6.8B
DTZ6.8B
DTZ6.8B
DTZ6.8B
DTZ6.8B
37
CDX-GT410U/GT414U
MAIN
Ref. No.
Part No.
Description
Remark
< JACK >
J1
J652
1-815-185-13 JACK (ANTENNA)
1-774-699-12 JACK, PIN 4P (BUS AUDIO IN,
AUDIO OUT REAR/SUB)
< JUMPER RESISTOR >
Ref. No.
Part No.
Description
JC929
JC930
JC931
JC932
JC933
1-216-296-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
Remark
JC934
JC935
JC936
JC938
JC939
1-216-296-11
1-216-296-11
1-216-296-11
1-216-296-11
1-216-296-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
JC940
JC941
JC942
JC943
1-216-296-11
1-216-864-11
1-216-864-11
1-216-296-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
JC1
JC4
JC5
JC8
JC9
1-216-864-11
1-216-296-11
1-216-296-11
1-216-296-11
1-216-864-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
JC10
JC11
JC12
JC14
JC16
1-216-296-11
1-216-864-11
1-216-296-11
1-216-296-11
1-216-296-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
JC17
JC18
JC19
JC21
JC22
1-216-864-11
1-216-864-11
1-216-296-11
1-216-296-11
1-216-296-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
JC23
JC24
JC28
JC29
JC30
1-216-296-11
1-216-864-11
1-216-864-11
1-216-296-11
1-216-296-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
JC31
JC32
JC33
JC36
JC38
1-216-296-11
1-216-296-11
1-216-296-11
1-216-864-11
1-216-296-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
JC401
JC705
JC810
JC811
JC901
1-216-296-11
1-216-296-11
1-216-296-11
1-216-296-11
1-216-864-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
JC902
JC903
JC904
JC905
JC906
1-216-296-11
1-216-296-11
1-216-864-11
1-216-864-11
1-216-296-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
JC907
JC909
JC910
JC911
JC912
1-216-864-11
1-216-296-11
1-216-864-11
1-216-296-11
1-216-296-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
Q1
Q3
Q50
Q401
Q402
8-729-027-43
6-551-431-01
8-729-600-22
8-729-027-44
8-729-027-44
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC114EKA-T146
2SC6027T100-QR
2SA1235-F
DTC114TKA-T146
DTC114TKA-T146
JC913
JC914
JC920
JC921
JC922
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-864-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
Q411
Q412
Q420
Q432
Q440
8-729-027-43
8-729-027-23
8-729-027-44
6-550-752-01
8-729-027-44
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC114EKA-T146
DTA114EKA-T146
DTC114TKA-T146
DTC614TKT146
DTC114TKA-T146
JC923
JC924
JC926
JC927
JC928
1-216-864-11
1-216-296-11
1-216-296-11
1-216-864-11
1-216-296-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
0
0
0
0
0
Q452
Q460
Q470
Q491
Q492
6-550-752-01
8-729-027-44
8-729-027-44
8-729-027-23
8-729-027-43
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
DTC614TKT146
DTC114TKA-T146
DTC114TKA-T146
DTA114EKA-T146
DTC114EKA-T146
Q605
8-729-027-43 TRANSISTOR DTC114EKA-T146
38
< COIL >
L1
L2
L3
L4
L50
1-216-295-11
1-216-809-11
1-216-809-11
1-216-864-11
1-216-295-11
SHORT CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
SHORT CHIP
0
100
100
0
0
L151
L300
L401
L402
L403
1-500-245-11
1-456-617-11
1-216-864-11
1-216-295-11
1-216-295-11
INDUCTOR, FERRITE BEAD
COIL, CHOKE
SHORT CHIP
0
SHORT CHIP
0
SHORT CHIP
0
L405
L406
L407
L409
L410
1-469-876-11
1-500-245-11
1-216-864-11
1-469-844-11
1-216-864-11
SHORT CHIP
0
INDUCTOR
2.2uH
SHORT CHIP
0
L411
L501
L802
L803
L804
1-216-864-11
1-216-864-11
1-416-831-11
1-457-384-11
1-216-295-11
SHORT CHIP
SHORT CHIP
INDUCTOR
COIL, CHOKE
SHORT CHIP
0
0
100uH
47uH
0
L805
L818
L901
L902
1-216-295-11
1-457-383-11
1-216-295-11
1-469-844-11
SHORT CHIP
COIL, CHOKE
SHORT CHIP
INDUCTOR
0
100uH
0
2.2uH
5%
5%
< TRANSISTOR >
1/10W
1/10W
CDX-GT410U/GT414U
MAIN
Ref. No.
Q664
Q701
Q702
Q805
Part No.
Description
8-729-027-23
8-729-120-28
8-729-120-28
8-729-027-43
TRANSISTOR
TRANSISTOR
TRANSISTOR
TRANSISTOR
Remark
DTA114EKA-T146
2SC1623-L5L6
2SC1623-L5L6
DTC114EKA-T146
Ref. No.
Part No.
Description
R450
R451
R452
R460
R461
1-216-833-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
100
100
100
1K
5%
5%
5%
5%
5%
Remark
1/10W
1/10W
1/10W
1/10W
1/10W
R462
R470
R471
R472
R485
1-216-833-11
1-216-809-11
1-216-821-11
1-216-833-11
1-218-883-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
100
1K
10K
33K
5%
5%
5%
5%
0.5%
1/10W
1/10W
1/10W
1/10W
1/10W
R491
R493
R502
R503
R504
1-216-805-11
1-216-864-11
1-216-809-11
1-216-809-11
1-218-871-11
METAL CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
47
0
100
100
10K
5%
1/10W
5%
5%
0.5%
1/10W
1/10W
1/10W
R505
R509
R510
R511
R517
1-218-871-11
1-216-809-11
1-216-809-11
1-216-809-11
1-216-841-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
100
100
100
47K
0.5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R519
R520
R521
R522
R523
1-216-845-11
1-216-809-11
1-216-825-11
1-216-825-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
100
2.2K
2.2K
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R526
R529
R531
R532
R533
1-216-845-11
1-216-809-11
1-216-841-11
1-216-845-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
100
47K
100K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R534
R536
R537
R540
R544
1-216-833-11
1-216-845-11
1-216-845-11
1-216-845-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
100K
100K
100K
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R551
R552
R553
R555
R556
1-216-845-11
1-216-845-11
1-216-839-11
1-216-845-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
100K
33K
100K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R557
R558
R559
R561
R563
1-216-809-11
1-216-833-11
1-216-845-11
1-216-845-11
1-216-845-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
10K
100K
100K
100K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R564
R565
R567
R568
R570
1-216-845-11
1-216-845-11
1-216-845-11
1-216-849-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
100K
100K
220K
100
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R573
R591
R592
R593
R595
1-216-845-11
1-216-864-11
1-216-809-11
1-216-809-11
1-216-833-11
METAL CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100K
0
100
100
10K
5%
1/10W
5%
5%
5%
1/10W
1/10W
1/10W
R596
R597
R598
1-216-833-11 METAL CHIP
1-216-864-11 SHORT CHIP
1-216-864-11 SHORT CHIP
5%
1/10W
< RESISTOR >
R1
R2
R3
R4
R5
1-216-809-11
1-216-839-11
1-216-843-11
1-216-839-11
1-216-843-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
33K
68K
33K
68K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R6
R7
R8
R9
R10
1-216-809-11
1-216-809-11
1-216-839-11
1-216-843-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
33K
68K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R12
R13
R15
R52
R53
1-216-864-11
1-216-864-11
1-216-864-11
1-216-845-11
1-216-797-11
SHORT CHIP
SHORT CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
0
0
0
100K
10
R54
R55
R57
R58
R60
1-414-595-11
1-216-797-11
1-216-833-11
1-216-821-11
1-216-864-11
METAL CHIP
10
METAL CHIP
10K
METAL CHIP
1K
SHORT CHIP
0
R61
R150
R151
R152
R153
1-216-864-11
1-216-864-11
1-216-817-11
1-216-817-11
1-216-834-11
SHORT CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
0
470
470
12K
R154
R155
R156
R157
R158
1-216-834-11
1-216-825-11
1-216-864-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
R301
R302
R351
R354
R355
1-216-811-11
1-216-841-11
1-216-845-11
1-216-864-11
1-216-833-11
R356
R357
R358
R401
R402
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
5%
5%
5%
1/10W
1/10W
1/10W
12K
2.2K
0
0
0
5%
5%
1/10W
1/10W
METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
150
47K
100K
0
10K
5%
5%
5%
1/10W
1/10W
1/10W
5%
1/10W
1-216-833-11
1-216-821-11
1-216-821-11
1-216-817-11
1-216-817-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
1K
1K
470
470
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R403
R404
R411
R420
R421
1-216-837-11
1-216-837-11
1-216-864-11
1-216-809-11
1-216-821-11
METAL CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
22K
22K
0
100
1K
5%
5%
1/10W
1/10W
5%
5%
1/10W
1/10W
R430
R431
R440
R442
R447
1-216-809-11
1-216-809-11
1-216-809-11
1-216-821-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
100
100
1K
10K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R448
R449
1-216-833-11 METAL CHIP
1-216-833-11 METAL CHIP
10K
10K
5%
5%
1/10W
1/10W
10K
0
0
39
CDX-GT410U/GT414U
MAIN
Ref. No.
SERVO
Part No.
Description
R599
R600
R601
R602
R603
1-216-864-11
1-216-845-11
1-216-851-11
1-216-851-11
1-216-821-11
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
0
100K
330K
330K
1K
Remark
R604
R606
R607
R611
R612
1-216-835-11
1-216-821-11
1-216-821-11
1-216-864-11
1-216-809-11
METAL CHIP
METAL CHIP
METAL CHIP
SHORT CHIP
METAL CHIP
R615
R616
R636
R671
R672
1-216-809-11
1-216-864-11
1-216-845-11
1-216-809-11
1-216-809-11
R673
R674
R701
R702
R703
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
15K
1K
1K
0
100
5%
5%
5%
1/10W
1/10W
1/10W
5%
1/10W
METAL CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
100
0
100K
100
100
5%
1/10W
5%
5%
5%
1/10W
1/10W
1/10W
1-218-871-11
1-216-845-11
1-216-821-11
1-216-841-11
1-216-833-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
100K
1K
47K
10K
0.5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R704
R705
R706
R707
R708
1-216-833-11
1-249-425-11
1-216-841-11
1-216-841-11
1-216-829-11
METAL CHIP
CARBON
METAL CHIP
METAL CHIP
METAL CHIP
10K
4.7K
47K
47K
4.7K
5%
5%
5%
5%
5%
1/10W
1/4W
1/10W
1/10W
1/10W
R709
R710
R800
R802
R803
1-216-833-11
1-216-864-11
1-216-829-11
1-216-825-11
1-216-825-11
METAL CHIP
SHORT CHIP
METAL CHIP
METAL CHIP
METAL CHIP
10K
0
4.7K
2.2K
2.2K
5%
1/10W
5%
5%
5%
1/10W
1/10W
1/10W
R809
R810
R811
R812
R813
1-216-821-11
1-216-832-11
1-216-821-11
1-216-822-11
1-216-821-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1K
8.2K
1K
1.2K
1K
5%
5%
5%
5%
5%
1/10W
1/10W
1/10W
1/10W
1/10W
R814
R815
R816
R817
R818
1-216-823-11
1-216-829-11
1-218-883-11
1-218-869-11
1-218-878-11
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
METAL CHIP
1.5K
4.7K
33K
8.2K
20K
5%
5%
0.5%
0.5%
0.5%
1/10W
1/10W
1/10W
1/10W
1/10W
R819
R820
R890
R891
R901
1-216-844-11
1-216-851-11
1-216-864-11
1-216-864-11
1-216-809-11
METAL CHIP
METAL CHIP
SHORT CHIP
SHORT CHIP
METAL CHIP
82K
330K
0
0
100
5%
5%
1/10W
1/10W
5%
1/10W
R902
R903
R910
R912
R913
1-216-809-11
1-216-809-11
1-216-864-11
1-216-864-11
1-216-864-11
METAL CHIP
METAL CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
100
100
0
0
0
5%
5%
1/10W
1/10W
R914
R915
R916
R917
R918
1-216-190-00
1-216-190-00
1-216-190-00
1-216-845-11
1-216-864-11
RES-CHIP
RES-CHIP
RES-CHIP
METAL CHIP
SHORT CHIP
470
470
470
100K
0
5%
5%
5%
5%
1/8W
1/8W
1/8W
1/10W
R919
R920
R923
1-216-864-11 SHORT CHIP
1-216-864-11 SHORT CHIP
1-216-864-11 SHORT CHIP
Ref. No.
Part No.
Description
R924
R925
R926
R927
R951
1-216-845-11
1-216-864-11
1-216-864-11
1-216-864-11
1-216-797-11
METAL CHIP
SHORT CHIP
SHORT CHIP
SHORT CHIP
METAL CHIP
R952
R961
1-216-797-11 METAL CHIP
1-216-864-11 SHORT CHIP
Remark
100K
0
0
0
10
10
0
5%
1/10W
5%
1/10W
5%
1/10W
< SWITCH >
S103
1-786-826-11 SWITCH, TACTILE (RESET)
< THERMISTOR (POSITIVE) >
TH400
1-803-350-21 THERMISTOR, POSITIVE
< TUNER UNIT >
40
0
0
0
TU1
A-3220-961-B TUNER UNIT (TUX-032)
< VIBRATOR >
X50
1-813-173-11 VIBRATOR, CRYSTAL (8.664MHz)
X501
1-813-524-21 VIBRATOR, CERAMIC (18.432MHz)
X502
1-813-202-11 VIBRATOR, CRYSTAL (32.768kHz)
*************************************************************
A-1206-357-A SERVO BOARD, COMPLETE
**********************
*************************************************************
MISCELLANEOUS
***************
7
0 103
X-2149-672-1 SERVICE ASSY, OP (DAX-25A)
CN902 1-820-877-11 CONNECTOR, USB (SOCKET) (USB)
F901
1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) 10A
*************************************************************
ACCESSORIES
************
1-479-077-13 REMOTE COMMANDER (RM-X151)
2-548-729-01 LID, BATTERY CASE (for RM-X151)
2-890-967-31 MANUAL, INSTRUCTION (ENGLISH,GERMAN,
FRENCH,ITALIAN,DUTCH)
2-890-967-61 MANUAL, INSTRUCTION (RUSSIAN) (RU)
2-890-968-31 MANUAL, INSTRUCTION, INSTALL (ENGLISH,
GERMAN,FRENCH,ITALIAN,DUTCH)
2-890-968-61 MANUAL, INSTRUCTION, INSTALL (RUSSIAN)
(RU)
X-2149-228-2 CASE ASSY (for FRONT PANEL)
*************************************************************
CDX-GT410U/GT414U
Ref. No.
Part No.
Description
Remark
PARTS FOR INSTALLATION AND CONNECTIONS
***************************************
151
152
153
154
155
X-3382-647-1
2-686-803-01
3-246-471-01
X-3382-926-1
3-349-410-11
156
157
1-465-459-31 ADAPTOR, ANTENNA
151
FRAME ASSY, FITTING
COLLAR
KEY (FRAME)
SCREW ASSY (BS), FITTING
BUSHING
152
153
×2
154
156
155
157
41
CDX-GT410U/GT414U
MEMO
42
CDX-GT410U/GT414U
REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper on the revised page allows you to jump to the next revised page.
Ver.
Date
Description of Revision
1.0
2006.10
New
1.1
2007.03
Notes for removal of the OPTICAL PICK-UP added.
(SUPPLEMENT-1)
4
(ENG-07003)

SERVICE MANUAL

Transcription

Similar documents

CDX-F7710/F7710S/F7715X - Philips Parts and Accessories

Il mito e la realtà - The BSC Group of Company

c.Y B-003

La memoria del futuro

Duplo-Dinamico

Untitled - Ra Records

Slides - Agenda

scarica il catalogo pdf - Collezione PIERRE gioielli floreali

scarica una parte del libro in pdf

anno III numero 28/29

ricerca guasti nei circuiti microcontroller

modifiche utili baofeng uv-5r